moke larm
S A
Manual
For alarm models:
0915CA
0916CA
PE9CA
0918CA
SINGLE STATION
Download from Www.Somanuals.com. All Manuals Search And Download
SMOKE ALARM
Contents
Installation
Recommended Locations
Introduction . . . . . . . . . . . . . . . . . . . . . . . . 1
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . 11-14
Fire Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . 15-18
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20
• Locate the first alarm in the immediate area of the
bedrooms. Try to protect the exit path, as the
bedrooms are usually farthest from the exit. If more
than one sleeping area exists, locate additional alarms
in each sleeping area (Image 1A).
• Locate additional alarms to protect any stairway as
stairways act like chimneys for smoke and heat.
• Locate at least one alarm on every floor level (Image 1B).
• Locate an alarm in every bedroom.
130 Esna Park Drive, Markham ON L3R 1E3
Consumer Hotline: 1-800-880-6788
• Locate an alarm in every room where electrical
appliances are operated (i.e. portable heaters or
humidifiers).
Made in China. Patents Pending
• Locate an alarm in every room where someone sleeps
with the door closed. The closed door may prevent
the alarm from waking the sleeper.
Introduction
• Smoke, heat, and combustion products rise to the
ceiling and spread horizontally. Mounting the smoke
alarm on the ceiling in the center of the room places it
closest to all points in the room. Ceiling mounting is
preferred in ordinary residential construction.
Models
0915CA, 0916CA, PE9CA and 0918CA
Thank you for purchasing this smoke alarm. It is an
important part of your family’s home safety plan. You
can trust this product to provide the highest quality safety
protection. We know you expect nothing less when the
lives of your family are at stake.
• When mounting an alarm on the ceiling, locate it at a
minimum of 10 cm (4") from the side wall (Image 2A).
• When mounting the alarm on the wall, use an inside
wall with the top edge of the alarm at a minimum of
10 cm (4") and a maximum of 30.5 cm (12") below the
ceiling (Image 2A).
Please take a few minutes to thoroughly read this alarm
manual, and save it for future reference. Teach children
how to respond to the alarms, and that they should never
play with the unit.
• Put smoke alarms at both ends of a bedroom hallway
or large room if the hallway or room is more than
9.1 m (30') long.
If you have any questions about the operation or
installation of your alarm, please call our toll free
Consumer Hotline at 1-800-880-6788.
• For mobile home installation, select locations carefully
to avoid thermal barriers that may form at the ceiling.
For more details, see Mobile Homes.
Image 1C will help you determine the correct location of
safety products that will help make your home a safer place.
IMPORTANT: Read all instructions before installation and keep
this manual near the alarm for future reference.
WARNING: Battery door will not close unless battery is present.
Removal of battery will render the smoke alarm inoperative.
Do not try to repair the smoke alarm yourself. Refer to the
NOTE: Any statements referring to a battery, applies to both
batteries used with model 0918CA.
instructions in Warranty section for service.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Installation
Installation
Locations to Avoid
• Do not install within 0.9 m (3') of the following: The
door to a kitchen, or a bathroom that contains a tub or
shower, forced air ducts used for heating or cooling,
ceiling or whole house ventilating fans, or other high
air-flow areas.
• Do not place the alarm where drapes or other objects
will block the sensor. Smoke must be able to reach the
sensor to accurately detect conditions.
• Do not install in peaks of vaulted ceilings, “A” frame
ceilings or gabled roofs. (Less than 10 cm (4") from the
peak of an “A” frame type ceiling.)
• Install at least 30.5 cm (12") away from fluorescent
lights as electronic noise may cause nuisance alarms.
SINGLE FLOOR PLAN
IMAGE 1A
MULTIPLE FLOOR PLAN
IMAGE 1B
• Keep out of insect infested areas. Avoid excessively
dusty, dirty or greasy areas. Dust particles may cause
nuisance alarms or failure to alarm.
• Install smoke alarms on sloped, peaked or cathedral
ceilings at or within 0.9 m (3') of the highest point
(measured horizontally). NFPA Standard 72 states:
“Smoke alarms in rooms with ceiling slopes greater than
0.3 m in 2.4 m (1 foot in 8 feet) horizontally shall be
located on the high side of the room.” NFPA Standard
72 states: “A row of detectors shall be spaced and
located within 0.9 m (3') of the peak of the ceiling
measured horizontally” (Image 2B).
• Extreme temperatures may effect the sensitivity of the
alarm. Do not install in areas where the temperature is
colder than 4.4°C (40°F) or hotter than 37.8°C (100°F).
• Do not install in areas where the relative humidity (RH)
is greater than 85%. Very humid areas, with moisture or
steam, can cause nuisance alarms.
• Avoid placing ionization smoke alarms in kitchen areas.
Normal cooking may cause nuisance alarms. If a
kitchen alarm is desired, it should have an alarm silence
feature or be a photoelectric type.
• Do not place in the garage. Particles of combustion are
present when you start your automobile.
• Smoke alarms are not to be used with detector guard s
unless the combination (alarm and guard) has been
evaluated and found suitable for that purpose.
IMAGE 1C
TOTAL HOME PROTECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
4
3
Installation
Installation
Mounting
10 cm (4”)
MINIMUM
CAUTION: This unit is sealed. The cover is not removable!
CEILING
NOTE: Any statements referring to a battery, applies to both
batteries used with model 0918CA.
NOTE: Any statements referring to a battery reminder tab,
applies to both battery reminder tabs used with model 0918CA.
• Remove the mounting plate from the back of the alarm
by holding the plate and twisting the alarm in the
direction indicated by the “OFF” arrow on the alarm
cover.
NEVER HERE
BEST
PLACEMENT
• To ensure aesthetic alignment of the alarm with the
hall-way, or wall, the “A” line on the mounting plate
must be parallel with the hallway when ceiling-
mounted, or h o ri zontal when wall mounted (Image 3A).
ACCEPTABLE
PLACEMENT
• Secure the mounting plate to the wall or ceiling with
the anchors and screws provided (Image 3B).
SIDE WALL
• For aesthetic reasons, the suggested position for wall
mounting is with the button(s) facing down (Image 3C).
IMAGE 2A
• Press the battery reminder tab down into the battery
compartment while inserting the battery (Image 3E).
CAUTION: If the battery reminder tab is not held down in the
battery compartment by the battery, the battery door will not
close and the unit will not attach to the mounting plate.
NOT IN
THIS AREA
• Alignment marks are provided on the edge of the
mounting plate and the alarm. After installing the
mounting plate, place the alarm onto the mounting plate,
making sure the alignment marks are lined up. Twist the
alarm in the direction indicated by the “ON” arrow on
the alarm cover (Image 3D) until it locks in place.
10 cm (4”)
BEST
ANYWHERE IN
THIS AREA
0.9 m (3’)
0.9 m (3’)
HORIZONTAL DISTANCE FROM PEAK
IMAGE 2B
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Installation
Installation
Alarm Tamper Resist Feature
• To make the smoke alarm tamper-resistant, a locking
pin has been provided in the bag with the screws and
anchors. Using this pin will deter children and others
from removing the alarm from the mounting plate. To
use the pin, insert it into the hole in the side of the
alarm after the alarm has been installed on the
mounting plate (Image 3F).
NOTE: The tamper-resistant pin will have to be removed in
order to change the battery. Use long nose pliers to pull the pin
out of the hole. It is now possible to remove the alarm from the
mounting plate.
“A” LINE
ALIGNMENT MARKS
IMAGE 3A
IMAGE 3B
Mobile Homes
Mobile homes built in the past five to seven years have
been designed to be energy efficient. Install smoke alarms
as recommended in Recommended Locations and Image 2A.
In mobile homes that are not well insulated compared to
present standards, extreme heat or cold can be transferred
from the outside to the inside through poorly insulated
walls and roof. This may create a thermal barrier that can
prevent the smoke from reaching an alarm mounted on
the ceiling. In such units, install the smoke alarm on an
inside wall with the top edge of the alarm at a minimum
of 10 cm (4") and a maximum of 30.5 cm (12") below the
ceiling (Image 2A).
SUGGESTED WALL
ROTATE TO MOUNT OR
TO REMOVE
MOUNTING POSITION
IMAGE 3C
IMAGE 3D
If you are not sure about the insulation in your mobile
home, or if you notice that the outer walls and ceiling are
either hot or cold, install the alarm on an inside wall. For
minimum protection, install at least one alarm close to the
bedrooms. For additional protection, see Image 1A.
WARNING: Test your smoke alarm operation after R.V. or mobile
home vehicle has been in storage, before each trip and at least
once a week during use.
BATTERY
REMINDER TAB
TAMPER-RESIST
LOCKING PIN
IMAGE 3E
IMAGE 3F
Download from Www.Somanuals.com. All Manuals Search And Download.
7
8
Operation
Operation
®
Models 0915CA, 0916CA, and 0918CA are designed to
detect products of combustion using the ionization
technique. They contain 0.9 microcurie of Americium 241,
a radioactive material. Distributed under U.S. NRC License
No. 32-23858-01E. Manufactured in compliance with U.S.
NRC safety criteria in 10 CFR 32.27. The purchaser is
exempt from any regulatory requirements. Do not try to
repair the smoke alarm yourself. Refer to the instructions
in Warranty section for service.
HUSH Control Feature
Models 0916CA, and 0918CA:
®
The Hush button is extremely useful in a kitchen area or
other areas prone to false alarms.
®
The Hush feature has the capability of temporarily
desensitizing the smoke alarm circuit for about 7 minutes.
This feature is to be used only when a known alarm
condition, such as smoke from cooking, activates the
alarm.
CAUTION: Due to the loudness (85 decibels) of the alarm, always
stand an arms-length away from the unit when testing.
If the alarm does sound, check for fires first. If a fire is
discovered, get out and call the fire department. If no fire
is present, check to see if one of the reasons listed in
Locations to Avoid may have caused the alarm.
• After installation, test your alarm by depressing and
holding down the test button for a minimum of 2
seconds. This will sound the alarm if the electronic
circuitry, horn, and battery is working. If the alarm
does not sound, the unit has a defective battery or
another failure.
®
The smoke alarm is desensitized by pushing the Hush
button on the smoke alarm cover. If the smoke is not too
dense, the alarm will silence immediately and“chirp”every
30-40 seconds for approximately 7 minutes. This indicates
that the alarm is in a temporarily desensitized condition.
The smoke alarm will automatically reset after
The smoke alarm is operating once a fresh battery is installed
and testing is complete. When the smoke alarm ionization
sensor chamber senses products of combustion, the horn will
sound a loud (85db) alarm until the sensing chamber is
cleared of smoke particles.
approximately 7 minutes. If after this period particles of
combustion are still present, the alarm will sound again.
®
The Hush feature can be used repeatedly until the air
has been cleared of the condition causing the alarm.
®
Pushing the Test button on the alarm will end the Hush
False Alarms
period.
®
Smoke alarms are designed to minimize false alarms.
Cigarette smoke will not normally set off the alarm, unless
the smoke is blown directly into the alarm.
NOTE: Dense smoke will override the Hush control feature
and sound a continuous alarm.
®
CAUTION: Before using the alarm Hush feature, identify the
source of the smoke and be certain a safe condition exists.
Combustion particles from cooking may set off the alarm if
the alarm is located close to the cooking area. Large
quantities of combustible particles are generated from
spills or when broiling. Using the fan on a range hood
that vents to the outside (non-recirculating type) will also
help remove these combustible particles from the kitchen.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
10
Maintenance
Maintenance
Testing
Alarm Removal
CAUTION: Due to the loudness (85 decibels) of the alarm,
always stand an arms length away from the unit when testing.
If the smoke alarm tamper resist feature has been
activated, refer to the Alarm Tamper Resist Feature section
for removal instructions.
Test by pushing the Test button on the cover and hold it
down for a minimum of 2 seconds. This will sound the
alarm if all the electronic circuitry, horn and battery are
working. If the alarm does not sound, the unit has a
defective battery or some other failure. DO NOT use an
open flame to test your alarm, you could damage the
alarm or ignite combustible materials and start a fire.
To remove the alarm from the mounting plate, rotate the
alarm in the direction of the “OFF” arrow on the cover.
Battery Replacement
This alarm has a low/missing battery monitor circuit which
will cause the alarm to “chirp” approximately every 30-40
seconds for a minimum of seven (7) days when the battery
gets low. Replace the battery when this condition occurs.
Test the alarm weekly to ensure proper operation. Erratic
or low sound coming from your alarm may indicate a
defective alarm, and it should be returned for service (see
Warranty section).
Models 0915CA, 0916CA, PE9CA and 0918CA use a 9 V
carbon zinc battery (alkaline and lithium batteries may also
be used). A fresh battery should last for one year under
normal operating conditions. Model 0916CA supplied with
a long-life battery uses a lithium battery such as the
Ultralife U9VL-J.
This smoke alarm is equipped with a flashing red
indicator light. The red LED is located under the test
button and will flash every 45 seconds to indicate that the
smoke alarm is receiving power.
Use only the following 9 volt batteries for replacement:
When products of combustion are sensed, the unit sounds
a loud 85db pulsating alarm, and the red LED rapidly
flashes every 2 seconds, until the air is cleared.
Carbon-Zinc Type Eveready 216 or 1222
Gold Peak 1604P or 1604S
Safety light equipped model 918CA will illuminate while
the alarm sounds, until the sensing chamber is cleared of
smoke particles.
Alkaline Type
Energizer 522
Duracell MN1604 or MX1604
Gold Peak 1604A
Lithium Type
Ultralife U9VL-J
For photoelectric model PE9CA. This alarm will “chirp” if
any components in the smoke sensing chamber fail. This
chirp will occur between the flashes of the red LED
indicator. (If the chirp occurs at the same time as the red
LED flash see Battery Replacement section for low battery
information.)
These batteries can be purchased at your local retailer.
WARNING: Use only the batteries specified above. Use of
different batteries than the recommended ones, may have a
detrimental effect on the smoke alarm. A good safety measure is
to replace the battery at least once a year, or at the same time
you change your clocks for daylight saving time. Be sure to
follow the battery installation instructions printed on the back of
the alarm.
Alarms failing an alarm test, or not operating normally,
must be replaced with a new alarm. Similarly, alarms more
than 10 years old must be replaced.
NOTE: WEEKLY TESTING IS REQUIRED!
NOTE: If after battery replacement the unit continues to
®
chirp, wait for approximately 7 minutes. The Hush
feature may have been activated accidentally while
changing the battery(ies) and will reset automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
12
Maintenance
Maintenance
Cleaning the Alarm
Safety Light
The alarm should be cleaned at least once a year.
Model 0918CA
• To clean your alarm, remove it from the mounting plate
as outlined in previous sections. You can clean the
alarm by using compressed air or a vacuum cleaner
hose with a soft brush attachment. Blow or vacuum
around the perimeter of the alarm to remove dust and
dirt. The outside of the alarm can be wiped with a
damp cloth (do not use a wet cloth to avoid water
entering the unit).
NOTE: If the safety light appears dim during regular testing,
replace both batteries immediately.
Use only the following 9 volt batteries for powering the
safet light:
Alkaline Type
Energizer 522
Duracell MN1604 or MX1604
These batteries can be purchased at your local retailer.
• After cleaning, reinstall your alarm and test your alarm
by using the Test button. If cleaning does not restore
the alarm to normal operation, the alarm should be
replaced.
The safety light has a 6.3 V 250mA fuse lamp with an
average life of 50 hours. If the safety light fails to operate
with a fresh alkaline battery, then replace the lamp.
• Do not paint the unit. Paint will seal the vents and
interfere with the sensor’s ability to detect smoke.
Never attempt to disassemble the unit or clean inside.
This action will void your warranty.
To replace the lamp, remove the alarm from the mounting
bracket by rotating the alarm in the direction of the “OFF”
arrow on the cover (Image 3D, and Alarm Tamper Resist
Feature section if this feature has been activated).
Open the battery door and remove both batteries from the
unit. Grip the lamp holder handle with your thumb and
finger and pull out the lamp holder assembly. Slide the
old lamp out of the lamp holder and replace it with a new
lamp.
Replacing the Alarm
The National Fire Protection Association (NFPA) and Kidde
recommend replacing this alarm ten years from the date
code label (located on the back of the alarm).
Replace with the correct lamp type: Vanco #FTB 6
which is available at most radio/tv repair stores.
Reinstall the lamp holder. It will snap easily into the base.
Put working batteries back in the alarm and remount the
alarm on its mounting bracket.
CAUTION: Use only the lamp specified. Use of a different lamp
may have a detrimental effect on the smoke alarm or the safety
light operation.
NOTE: The safety light is not intended to satisfy the
requirements for approved illumination under various local
codes. Very thick and/or dense smoke may obscure the light.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
14
Fire Safety
Fire Safety
WARNING: Please read carefully and thoroughly.
• If the alarm is located outside the bedroom or on a
different floor, it may not wake up a sound sleeper.
• NFPA Standard 72 states: Life safety from fire in
residential occupancies is based primarily on early
notification to occupants of the need to escape,
followed by the appropriate egress actions by those
occupants. Fire warning systems for dwelling units are
capable of protecting about half of the occupants in
potentially fatal fires. Victims are often intimate with
the fire, too old or young, or physically or mentally
impaired such that they cannot escape even when
warned early enough that escape should be possible.
For these people, other strategies such as protection-in-
place or assisted escape or rescue are necessary.
• The use of alcohol or drugs may also impair one’s
ability to hear the smoke alarm. For maximum
protection, a smoke alarm should be installed in each
sleeping area on every level of a home.
• Although smoke alarms can help save lives by
providing an early warning of a fire, they are not a
substitute for an insurance policy. Home owners,
landlords and tenants should have adequate insurance
to protect their lives and property.
• Smoke alarms are devices that can provide early
warning of possible fires at a reasonable cost; however,
alarms have sensing limitations. Ionization type alarms
offer a broad range of fire sensing capabilities but are
better at detecting fast flaming fires than slow
smoldering fires. Photoelectric alarms sense smoldering
fires better than flaming fires. Home fires develop in
different ways and are often unpredictable. Neither
type of alarm (photoelectric or ionization) is always
best, and a given alarm may not always provide
warning of a fire.
Good Safety Habits
Develop and practice a plan of escape!
• Install and maintain Fire extinguishers on every level of
the home and in the kitchen, basement and garage.
Know how to use a fire extinguisher prior to an
emergency.
• Make a floor plan indicating all doors and windows and
at least two (2) escape routes from each room. Second
story windows may need an escape ladder.
• A battery powered alarm must have a battery of the
specified type, in good condition and installed properly.
• Have a family meeting and discuss your escape plan,
showing everyone what to do in case of fire.
• AC powered alarms (without battery backup) will not
operate if the AC power has been cut off, such as by an
electrical fire or an open fuse.
• Determine a place outside your home where you all
can meet if a fire occurs.
• Familiarize everyone with the sound of the smoke alarm
and train them to leave your home when they hear it.
• Smoke alarms must be tested regularly to make sure the
batteries and the alarm circuits are in good operating
condition.
• Practice a fire drill at least every six months, including
fire drills at night. Ensure that small children hear the
alarm and wake when it sounds. They must wake up in
order to execute the escape plan. Practice allows all
occupants to test your plan before an emergency. You
may not be able to reach your children. It is important
they know what to do.
• Smoke alarms cannot provide an alarm if smoke does
not reach the alarm. Therefore, smoke alarms may not
sense fires starting in chimneys, walls, on roofs, on the
other side of a closed door or on a different floor.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
16
Fire Safety
Fire Safety
Alarm Exit Procedure
Additional Recommendations
• Alert small children in the home.
The National Fire Protection Association’s Standard 72
provides the following information:
• Leave immediately by your escape plan. Every second
counts, so don’t waste time getting dressed or picking
up valuables.
Smoke alarms shall be installed outside each separate
sleeping area in the immediate vicinity of the bedrooms
and on each additional story of the family living unit,
including basements and excluding crawl spaces and
unfinished attics. In new construction, a smoke alarm also
shall be installed in each sleeping room.
• In leaving, don’t open any inside door without first
feeling its surface. If hot, or if you see smoke seeping
through cracks, don’t open that door! Instead, use your
alternate exit. If the inside of the door is cool, place
your shoulder against it, open it slightly and be ready to
slam it shut if heat and smoke rush in.
Smoke Detection - Are More Smoke Alarms Desirable?
Required number of smoke alarms (as shown in Image 1A
and Image 1B): The required number of smoke alarms
might not provide reliable early warning protection for
those areas separated by a door from the areas protected
by the required smoke alarms. For this reason, it is
recommended that the householder consider the use of
additional smoke alarms for those areas for increased
protection.
• Stay close to the floor if the air is smoky. If possible do
not breathe too deeply to avoid smoke inhalation.
Breathe through a cloth (preferably wet) if possible.
• Once outside, go to your selected meeting place and
make sure everyone is there.
• Call the fire department from your neighbor’s home -
not from yours!
The additional areas include the basement, bedrooms,
dining room, furnace room, utility room, and hallways not
protected by the required smoke alarms. The installation
of the smoke alarms in the kitchen, attic (finished or
unfinished), or garage is normally not recommended, as
these locations occasionally experience conditions that can
result in improper operation.
• Don’t return to your home until the fire officials say that
it is all right to do so.
• There are situations where a smoke alarm may not be
effective to protect against fire as stated in the NFPA
Standard 72. For instance:
- smoking in bed;
- leaving children unsupervised;
- cleaning with flammable liquids, such as gasoline.
Alarms should be installed in accordance with the National
Fire Protection Association’s Standard 72 (NFPA,
Batterymarch Park, Quincy, MA 02269).
Notify your local fire department and insurance company
of your smoke alarm installation.
NRC Information
Ionization type smoke alarms use a very small amount of
a radioactive element in the sensing chamber to enable
detection of visible and invisible combustion products.
The radioactive element is safely contained in the chamber
and requires no adjustments or maintenance. This smoke
alarm meets or exceeds all government standards. It is
manufactured and distributed under license from the U.S.
Nuclear Regulatory Commission.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
18
Warranty
Warranty
If after reviewing this manual you feel that your smoke
alarm is defective in any way, do not tamper with the unit.
In many cases, the quickest way to exchange your alarm
is to return it to the original place of purchase.
Alternatively, you may return it for servicing to Kidde.
If you have questions, call Kidde Customer Service at
1-800-880-6788.
Model 0916CA with Ultralife lithium battery:
10 Year Limited Warranty
Kidde warrants to the Purchaser that this enclosed smoke
alarm, and Ultralife Batteries Inc. warrants to the Purchaser
that the enclosed Ultralife 9 volt lithium battery when used
with this enclosed smoke alarm, will be free from defects in
material, workmanship or design under normal use and
service for a period of ten years from the date of purchase.
5 Year Limited Warranty
Kidde warrants to the original purchaser that this enclosed
smoke alarm (but not the battery) will be free from defects in
material and workmanship or design under normal use and
service for a period of five years from the date of purchase.
The obligation of Kidde under this warranty is limited to
repairing or replacing this smoke alarm, or any part which we
find to be defective in material, workmanship or design, free of
c h a rge to the customer.
The obligation of Kidde under this warranty is limited to
repairing or replacing this smoke alarm or any part which we
find to be defective in material, workmanship or design, free
of charge to the customer, upon sending this smoke alarm
with proof of date of purchase, postage and return postage
prepaid, to Kidde, Customer Service Department, 130 Esna
Park Drive, Markham, ON L3R 1E3. 1-800-880-6788.
To return a defective Ultralife battery, return the battery along
with proof of purchase and a note describing the nature of
difficulty to: Ultralife Batteries Inc., P.O. Box 622, 1350 Route
88 South, Newark, New York 14513. To return a defective
smoke alarm, return this alarm along with proof of date of
purchase, postage and return postage prepaid to: Kidde,
Customer Service Department, 130 Esna Park Drive, Markham
ON L3R 1E3. 1-800-880-6788.
This warranty shall not apply to this smoke alarm if it has
been damaged, modified, abused or altered after the date of
purchase or if it fails to operate due to improper maintenance
or inadequate AC or DC electrical power.
This warranty shall not apply to this smoke alarm if it has
been damaged, modified, abused or altered after the date of
purchase or if it fails to operate due to improper maintenance
or inadequate AC or DC electrical power.
The liability of Kidde or any of its parent or subsidiary corporations
arising from the sale of this smoke alarm or under the terms of this
limited warranty shall not in any case exceed the cost of
replacement of this smoke alarm and, in no case shall Kidde or
any of its parent or subsidiary corporations be liable for
consequential loss or damages resulting from the failure of this
smoke alarm or for breach of this or any other warranty, express
or implied, even if the loss or damage is caused by the company’s
negligence or fault.
The liability of Kidde or any of its parent or subsidiary corporations
arising from the sale of this smoke alarm or the enclosed Ultralife
battery under the terms of this limited warranty shall not in any
case exceed the cost of replacement of this smoke alarm or this
battery and in no case shall Kidde or any of its parent or subsidiary
corporations be liable for consequential loss or damages resulting
f rom the failure of this smoke alarm or for breach of this or any
other warranty, express or implied, even if the loss or damage is
caused by the company’s negligence or fault.
Since some provinces do not allow limitations on the duration
of an implied warranty or do not allow the exclusion or
limitation of incidental or consequential damages, the above
limitations or exclusions may not apply to you. While this
warranty gives you specific legal rights, you may also have
other rights which vary from province to province.
Since some provinces do not allow limitations on the duration
of an implied warranty or do not allow the exclusion or
limitation of incidental or consequential damages, the above
limitations or exclusions may not apply to you. While this
warranty gives you specific legal rights, you may also have
other rights which vary from province to province.
Also, Kidde makes no warranty, express or implied, written or
oral, including that of merchantability or fitness for any
particular purpose, with respect to the battery.
The above warranty may not be altered except in writing
signed by both parties hereto.
The above warranty may not be altered except in writing
signed by both parties hereto.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
20
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
21
|