Patent:
5,890,320
KidCo is a member of:
User Guide
HearthGate Model G70
Made in Denmark for:
KidCo, Inc.
300 Terrace Drive
Mundelein, IL 60060
For hearths 6’ wide by 2’ deep
Phone
Fax
847-970-9100
847-970-9109
Optional 8” section (G70-8) or 24” section (G70-24)
available for larger areas.
Patents pending
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Assembly
Unpack your folded HearthGate™ on a
Removing or adding sections:
1.
2.
3.
4.
5.
6.
7.
8.
stable surface, making sure handle is on top.
Each corner is connected by plastic, inter-
locking hinges.
Note: Always begin separating gate from
either end. At the juncture of every section is
a removable, vertical bar.
How to adjust the sections:
To remove vertical bar, lift up on bar (5), while
sliding it out of lower hinge groove (6a.). Pull
bar down and out of cone (6.).
2. 1.
6a.
3.
A spring is fitted in all cones which delib-
erately creates tension when adjusting.
At corner, lift up slightly on section with hinge
teeth facing down (1) while gently pressing
down on connected section (2). Rotate sec-
tions to desired position. (3). Release to lock
into place.
2a.
Hinge
Lift
Down
Note: Each hinge adjusts from 0˚ to 270˚ in
10˚ increments.
Lift off end section. If gate is now appropriate
length, go to step 8.
Removable cone
Cones
Cones
Removable cone
If additional section/s are required, go to
steps 11 & 12.
Removable cap
Removable cap
Position HearthGate™ to desired shape,
taking into account recommended 20” mini-
mum distance described in ”Important
Notes” on page 2. It may be necessary to
remove or add section/s to gate to fit your
application.
Depending on number of sections removed,
you will end up with one of two configurati-
ons at the end of gate (diagram 8 or 9).
G
H
Remove hinge cap (H) from bottom of original
end section. A screwdriver may be used to
help pry it off. Place cap over top hinge on
what is now the end piece.
If making no changes, see ”Installation” steps
13 to 23.
If removing sections, see ”Assembly” steps 5
to 10.
Place spare hinge cover (G) over bottom
hinge. Go to step 10.
I
If adding sections, see ”Assembly” steps 5 to
7.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Installation
Remove hinge cap (H) from bottom of original
Installing the wall mountings:
9.
13.
14.
15.
16.
end section. A screwdriver may be needed to
pry it off. Place under bottom hinge. Remove
plastic cone from under top hinge of original
end section. Install cone (I) under top hinge
of new end section.
Fold wall cover (A) around vertical bar at end
of gate.
A
H
I
Insert lock fitting (B).
Reinstall a removable, vertical bar. Insert bar
by pressing it into upper hinge cone, while
sliding bar into groove of lower hinge. Spring
in cone will make bar lock in place.
10.
11.
12.
A
10a.
Proceed to ”Installation” steps 13 to 23.
B
Insert 3 wall cover screws (E) through oblong
holes in top, middle and bottom of assembly.
Adding optional section/s:
Remove vertical bar from optional section
(steps 5 & 6).
F
Note: Loosely screw on nuts (F), but do not
tighten at this time.
Position optional section with cone hinge at
top. Align cone hinge underneath top hinge
on end section. When the center of both hin-
ges are aligned, top and bottom, they will fall
together.
Insert removable bar (see step 10).
If adding more than one section, repeat the
process.
E
Reattaching end sections:
Align top cone corner of one section with the
top hinge of the end section. When the cen-
ter of both hinges are aligned, top and bott-
om, they will fall together.
Fasten wall plate (C) onto assembly. See
steps 17. a, b and c.
Insert removable bar.
Proceed to ”Installation” steps 13 to 23.
C
Note: The HearthGate™ cannot be com-
pletely folded when optional section/s have
been added.
Relocating the walk through door section:
The walk through door section can be repo-
sitioned in the configuration as long as it is
interchanged with a section that has
matching top and bottom hinges (refer to
diagram 3).
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
Center buttons of assembly with wall plate
Remove wall plate (C) from assembly by
17.
21.
22.
23.
24.
21a.
holes (17. a). When aligned, push buttons
through holes and slide down to lock (17. b
& c).
pressing locking tab (21a.) and lifting it off.
a
b
c
Buttons
C
Note: Screws provided are for mounting
directly into wood. If mounting into brick,
drywall or other surfaces, use appropriate
hardware.
Now it should look like this.
18.
19.
20.
D
Hold wall plate (C) inside outline and screw in
3 wood screws (D). Space screws evenly.
There are multiple holes in wall plate giving
many screw location options.
C
Reattach assembly to wall plate (see 17. a, b
and c).
Move HearthGate™ to desired location.
Tighten 3 sets of assembly screws and nuts.
Warning: A distance of a minimum of 20”
from source of heat/fire to gate is recom-
mended (see ”Important Notes” page 2). If
this is not possible with sections included,
optional 24” sections are available from your
HearthGate™ dealer or KidCo.
min. 20”
Slide the assembly as close to cone as pos-
sible (20a.). With a pencil, outline assembly
on mounting surface.
Now you are ready to mount other end of
HearthGate™. Follow steps 13 to 23.
20a.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
KIDCO LIMITED WARRANTY
Operation
Your KidCo product is warranted to be free from manufacturing defects for a period of one
year from date of purchase under normal non commercial use and in compliance with the
operating instructions. This warranty extends only to the original retail purchaser and is only
valid when supplied with proof of purchase.
Opening the walk through door:
25.
26.
27.
Squeeze handle up as much as possible (1).
The locking bar should release from bottom
frame (2).
KidCo will either repair, or at our option replace, free of charge, any parts necessary to correct
defects in material or workmanship during the warranty period. This warranty is complete and
exclusive. The warranty expressly disclaims liability for incidental, special and consequential
damages of any nature. Any implied warranty arising by operation of law shall be limited in
operation to the terms of this warranty. Some states do not allow the exclusion or limitation of
incidental or consequential damages or limitations on how long an implied warranty lasts, so
the above may not apply to you. This warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
Door can now swing open in either direction.
1.
Closing and locking the walk through
door:
SHOULD REPAIR OR PARTS BE NECESSARY
Should a repair be needed during the warranty period, ship the gate in the original carton or
similar protective container (check any retail store or purchase from UPS) and send freight
prepaid (we suggest UPS) to: KidCo, Inc., 300 Terrace Drive, Mundelein, IL 60060-3836.
While closing door, squeeze handle up as
much as possible (25.1.) and align bottom of
door with gate frame (25.2.).
Release handle and door should lock.
Gate should always be in the locked posi-
tion.
Include a note with your return address, day-time telephone number, and specify what is
wrong with the product. Repairs can normally be made within 48 hours after receipt at KidCo.
For additional information CALL our customer service department at (847) 970-9100.
PARTS PRICE LIST
CONFIGUREGATE - G80
Price
$7
Wall cover (1)
Door will be properly locked when handle
hook and bottom locking bar have engaged.
Test to ensure door is locked.
$7
$7
$1
$1
$1
$2
$2
$2
$7
Lock fittings (1)
Wall plates (1)
Wood screws (6)
Wall cover screws (6)
Wall cover nuts (6)
Hinge covers (1)
Hinge caps (1)
Cones (1)
Removable Verticle bar (1)
Gate Care
SHIPPING AND HANDLING
CHARGES
METHOD OF PAYMENT Please do not send cash.
Check/Money Order enclosed (Payable to: KidCo, Inc.)
If order includes wall covers,
lock fittings or wall plates add
$8.00
•
•
No part of the this gate requires lubri-
cation.
•
Do not use abrasive cleaners or bleach.
VISA (13 or 16 Digits)
Mastercard (16 Digits)
Mo.
Yr.
•
If using out doors, and to help prevent
rust, treat all exposed metal on the gate
with a rust inhibitor. Some rusting may still
occur.
Clean using warm soapy water, or a damp
cloth.
Credit card account number
Signature of cardholder
Please print name of cardholder
Name
Expiration date (required)
Date
All others add $5.00
Day time phone no.
Order amount
Shipping & handling
Total
$
$
$
Street Address
Unit
Zip
City
State
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|