Kicker Portable Speaker RS562 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.  
Features  
CIMP(Curvilinear Injection-Molded Polypropylene  
Woofer Cones) is a high performance composite, which  
remains rigid, minimizes cone flex and lowers harmonic  
distortion. The CIMPconsists of a one-piece, injection-  
molded polypropylene material that moves as a piston,  
exhibiting power and control.  
Spring-Loaded Nickel Plated Terminals flawlessly  
connect medium to heavy gauge speaker wire to the sleeved  
high-power tinsel lead wires.  
TeteronElliptical Dome Tweeter with Neodymium  
Magnet provides a smooth high frequency response with  
quick, detailed and spatially-correct imaging. The elliptical  
dome shape optimizes both off-axis (door panel mount) and  
on-axis response. It has a wide dispersion with increased  
efficiency.  
New Enhanced BAM (Basket and Motor) Assembly  
utilizes a high-dampening strength cast aluminum basket,  
features a low-profile open design, and provides a solid  
foundation for the precision-aligned motor assembly.  
High-Temp Polyimide Film Voice Coil Former  
improves sonic and conductive properties, and prevents  
thermal-electrical meltdown.  
Optimized Composite Rubber Surround Radius allows  
extended cone excursion for additional bass output and higher  
SPL. Composite rubber surround offers enhanced acoustical  
dampening and UV protection, and gives the RS-Series  
System Components cone maximum EXmax(effective  
excursion) potential.  
Ferro-Fluidcooled tweeter voice-coil extends the high  
frequency transducer’s life span.  
Kicker Marine Ready models come with water resistant  
mounting hardware. This enables the RS56.2 to replace stock  
boat speakers without rusting your ship.  
Flexible Mounting of the RS56.2, which includes an 6” x 8”  
(15.2 cm x 20.3 cm) mounting adapter, and the RS65.2 and  
RS56.2, which have coaxial mounts for the tweeters, enable  
the RS-Series System Components to accommodate most  
installations.  
Newly Designed Passive Crossover Network allows a  
seamless transition between the midrange and tweeter drivers.  
The Zobel circuitry keeps the tweeters’ impedance linear and  
the mylar by-pass capacitors extend the frequency response.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-Series System Components  
3
Performance  
Model:  
RS56.2  
RS65.2  
Speaker Design  
2 - Way  
2 - Way  
4
Rated Impedance, ohm  
DC Resistance, ohm  
4
3
3
Sensitivity [SPLo], dB @ 1W, 1m  
Power Range, Watts RMS  
Peak Power Handling, Watts  
Effective Frequency Range, Hz  
Top-Mount Depth, in (cm)  
Bottom-Mount Depth, in (cm)  
Mounting Hole Diameter, in (cm)  
Woofer Size, in (cm)  
87  
87  
6-90  
6-100  
180  
200  
50-21k  
40-21k  
2 9/16 (6.5)  
2 13/16 (7.1)  
5 (12.7)  
2 3/4 (7.0)  
3 (7.62)  
5 7/16 (13.8)  
6 (15.2)  
5 1/4 (13.3)  
Polypropylene  
Cast Aluminum  
Composite Rubber  
1 (2.54)  
Woofer Cone Material  
Polypropylene  
Cast Aluminum  
Composite Rubber  
1 (2.54)  
Woofer Basket Material  
Woofer Surround Material  
Tweeter Size, in (cm)  
Tweeter Design  
Elliptical Dome  
Teteron  
Neodymium  
Yes  
Elliptical Dome  
Teteron  
Neodymium  
Yes  
Tweeter Diaphragm Material  
Tweeter Magnet Material  
Outboard Crossover  
Speaker Wire  
Included  
18, 3500  
12, 3500  
Yes  
Included  
18, 3500  
12, 3500  
Yes  
High Pass, dB, at Frequency, Hz  
Low Pass, dB, at Frequency, Hz  
Grills Included  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KS-Series System Components  
4
Installation  
Your Kicker RS-Series System Component drivers are specifically designed for mounting in free-air applications. The speakers do  
not require a sealed enclosure for optimum performance. It is important to isolate the sound coming off the front of the driver from the  
sound radiating from the back of the driver. This isolation is usually accomplished by using the correct size driver in a factory speaker  
location.  
Mounting  
Use caution when mounting speakers through the rear deck or package tray of a vehicle. Please be aware of wiring harnesses,  
trunk springs, hinges, and folding seat mechanisms that may interfere with the operation of the car or speaker system. When running  
the speaker wires, be careful not to damage them with seat bolts or door screws.  
Note: To get the best performance from your Kicker RS-Series System Components,  
we recommend using genuine Kicker Accessories and Wiring.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
RS-Series System Components  
Installation  
If custom door mounting locations for the RS-Series System Components are desired, be careful to avoid interference from the  
window and door lock mechanisms. The first step is to find a location on the door panel that will accept the dimensions of the  
speaker. Then remove the door panel from the door, and check for operational clearance of the window. Cycle the window all the way  
down and up. If metal must be cut to mount the speakers, avoid structural metal and braces. An optional reinforcing panel (thin piece  
of wood or Medium Density Fiberboard) may be necessary if the door panel cannot support the weight of the speaker. Mount the  
speaker to the door panel and door body as outlined in Figure 1.  
If the factory door speaker wiring is not available, it will be necessary to run the supplied wire through the door jamb. The speaker  
wire should be kept away from sharp edges and avoid the possibility of getting pinched by the door. An existing grommet in the door  
jamb is the ideal place to run the speaker wire. If the factory hole and grommet do not exist or are inaccessible, you must drill a hole  
to run the speaker wire through the door jam. Be careful not to drill into other wiring or existing door mechanisms. Any time a wire is  
run through a hole, it is necessary to insert a rubber or plastic grommet to protect the wire from damage as outlined in Figure 2.  
Figure 1  
Figure 2  
(Optional)  
Stagger Holes  
For Wiring &  
Use Grommets  
(When Factory Holes and  
Grommets are not Available)  
Door Panel  
To Crossover  
Kick Panel  
Push Grill into place and  
snap onto Speaker  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-Series System Components  
6
Installation  
Tweeter Mounting  
The tweeter can be mounted one of four ways: flush, surface, angled and coaxial mounting. For flush mounting applications, please  
refer to the illustration in Figure 3. Mount the tweeter as high up on the door and as far forward as possible without interference from  
the dashboard. Choose a flat location on the door with space behind the panel to allow room for the mounting nut.  
After checking the clearances, cut a 2” (5.1 cm) hole in the door panel. Place the mounting nut behind the door panel. Feed the  
wire through the door and body panels. Mount the tweeter by screwing the tweeter onto the mounting nut.  
For surface mounting applications, remove the tweeter face plate by screwing it off and install the supplied smaller face plate. Use  
the surface mount cup as a template and drill a 7/64” (2.8 mm) hole in the center for attaching the cup to the door and a 5/16”  
(7.9 mm) hole for the wires. A #8 flathead sheet metal screw is supplied to attach the surface mount cup to the door panel. Position  
the tweeter over the surface mount cup and press it into position.  
Figure 3 (Flush Mount)  
Clearance Hole 2.5"  
Mounting Nut  
Door Body  
Tweeter  
Door Panel  
2" Hole  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
RS-Series System Components  
Installation  
Tweeter Mounting continued  
The tweeter can be mounted in the center of the midrange. This creates a high quality coaxial speaker. Remove the tweeter face  
plate by screwing it off and install the supplied smaller face plate. Remove the magnet boot from the midrange.  
Then install the tweeter back plate by securing the supplied phillips-head machine screw to the plate, as outlined in Step 1, in  
Figure 4. Unscrew the bullet shaped phase plug from the center of the midrange, Step 2. Feed the wires through the included pole  
mount, Step 3. Then, screw the assembly into the middle of the midrange, Step 4. Run the wire through the clip on the side of the  
basket and mount the speaker in the desired location, Step 5.  
Please use caution to run the wire through the channel on the back plate before clipping the wire on the basket and placing the  
magnet boot back on the midrange, this prevents damage to the speaker wire in shallow mounting depth installations.  
Figure 4  
Step 1  
Step 2  
Step 3  
Step 4  
Step 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-Series System Components  
8
Wiring Options  
There are three sets of wires supplied with the Kicker RS-Series System Components. One set is designed to plug on to the  
terminal of the midrange. The other end of this wire goes to the midrange output on the supplied crossover.  
The other two sets of wires do not have any connectors on either end. One set goes from the tweeter output of the crossover to the  
short wire coming out of the tweeter; join these wire with the supplied butt connectors. The last set of wires are used to join the inputs  
of the crossover to the outputs of your source unit or amplifier. Please see Figure 5.  
Figure 5  
If you have any questions about the installation of your Kicker  
RS-Series System Component Speakers, see the Authorized  
Tweeter  
Kicker Dealer where you made your purchase. For more advice  
on installation, click on the SUPPORT tab on the Kicker  
homepage, www.kicker.com. Choose the Technical Support tab,  
choose subject you are interested in, and then download or view  
the corresponding information. Please E-mail  
Butt  
Connecctors  
+
_
[email protected] or call Technical Services (405) 624-8583  
for specific or unanswered questions.  
Midrange  
SOURCE UNIT or AMPLIFIER  
_
_
107.5 FM THE END  
+
+
+
_
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-Series System Components  
9
Wiring Options  
Wiring two RS-Series System Components to a single channel  
Modern high performance system components have a lower DC Resistance than what used to be available. The Kicker RS-Series  
System Components are rated at four ohms and work with any source unit or amplifier designed to operate at a four ohm load. If you  
want to use two RS-Series System Components on each channel of your source unit or amplifier wire the system components in  
series--at the connection between the crossover and source unit or amplifier, as shown below in Figure 6. This will improve the sound  
quality, lower the total harmonic distortion and lessen the thermal load at the source unit or amplifier. This may prevent an amplifier  
from shutting down, due to over-current protection circuitry.  
Figure 6  
CROSSOVER  
to Tweeter  
to Tweeter  
CROSSOVER  
to Woofer  
to Woofer  
SOURCE UNIT or AMPLIFIER  
to Tweeter  
to Tweeter  
CROSSOVER  
CROSSOVER  
to Woofer  
to Woofer  
All specifications and performance figures are subject to change. Please visit kicker.com for the most current information.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
RS-Series System Components  
WHAT IS NOT COVERED?  
Acoustics LIMITED WARRANTY  
This warranty is valid only if the product is used for the purpose for which it was  
designed.  
It does not cover:  
Kicker warrants this product to be free from defects in material and workmanship  
under normal use for a period of THREE (3) MONTHS from date of original  
purchase with receipt. When purchased from an Authorized KICKER Dealer it is  
warranted for ONE (1) YEAR from date of original purchase with receipt. In all cases  
you must have the original receipt! Should service be necessary under this  
warranty for any reason due to manufacturing defect or malfunction during the  
warranty period, Kicker will repair or replace (at its discretion) the defective  
merchandise with equivalent merchandise at no charge. Warranty replacements  
may have cosmetic scratches and blemishes. Discontinued products may be  
replaced with more current equivalent products.  
Damage due to improper installation.  
Subsequent damage to other components.  
Damage caused by exposure to moisture, excessive heat, chemical cleaners,  
and/or UV radiation.  
Damage through negligence, misuse, accident or abuse. Repeated returns for  
the same damage may be considered abuse.  
Any cost or expense related to the removal or reinstallation of product.  
Speakers damaged due to amplifier clipping or distortion.  
Items previously repaired or modified by any unauthorized repair facility.  
Return shipping on non-defective items.  
Products with tampered or missing bar code labels.  
Products returned without a Return Authorization (RMA) number.  
Freight Damage.  
This warranty is valid only for the ORIGINAL PURCHASER and is not extended  
to owners of the product subsequent to the original purchaser. Any applicable  
implied warranties are limited in duration to a period of the express warranty as pro-  
vided herein beginning with the date of the original purchase at retail, and no war-  
ranties, whether express or implied, shall apply to this product thereafter. Some  
states do not allow limitations on implied warranties, therefore these exclusions may  
not apply to you. This warranty gives you specific legal rights; however you may  
have other rights that vary from state to state..  
The cost of shipping product to Kicker.  
Service performed by anyone other than Kicker.  
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE  
Defective merchandise should be returned to your local Authorized Stillwater  
Designs (Kicker) Dealer for warranty. Assistance in locating an Authorized Dealer  
can be obtained by writing, calling, or by visiting kicker.com. You can confirm that a  
dealer is authorized by asking to see a current authorized dealer window decal.  
HOW LONG WILL IT TAKE?  
Kicker strives to maintain a goal of 24-hour service for all acoustics (subwoofers,  
midrange drivers, tweeters, crossovers, etc) returns. Delays may be incurred if lack  
of replacement inventory or parts is encountered.  
If it becomes necessary for you to return defective merchandise directly to  
Stillwater Designs (Kicker), call the Kicker Customer Service Department at  
(405) 624-8510 for a Return Authorization (RMA) number. Package all defective  
items in the original container or in a package that will prevent shipping damage,  
and return to:  
INTERNATIONAL WARRANTY  
Contact your International Kicker dealer or distributor concerning specific  
procedures for your country’s warranty and service policies.  
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075  
The RMA number must be clearly marked on the outside of the package. Please  
return only defective components (tweeter, crossover, plug, etc.). The return of  
functioning items increases your return freight charges. Non-defective items  
received will be returned freight collect.  
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • (405) 624-8510  
KICKER drivers are capable of producing sound levels  
that can permanently damage your hearing! Turning up a  
system to a level that has audible distortion is more  
damaging to your ears than listening to an undistorted  
system at the same volume level. The threshold of pain  
Include a copy of the original receipt with the purchase date clearly visible, and a  
“proof-of-purchase” statement listing the Customer’s name, Dealer’s name and  
invoice number, and product purchased. Warranty expiration on items without proof-  
of-purchase will be determined from type of sale and the manufacturing date code.  
Freight must be prepaid; items sent freight collect, or COD, will be refused.  
is always an indicator that the sound level is too loud and  
WARNING:  
may permanently damage your hearing.  
Failure to follow these steps may void your warranty. Any questions can be  
directed to the Kicker Customer Service Department at (405) 624-8510.  
Please use common sense when controlling volume!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03162005+05RS  
11  
RS-Series System Components  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ingersoll Rand Impact Driver 772 User Manual
Jabra Headphones GN1200 User Manual
JVC GPS Receiver KW NT300 User Manual
JVC MP3 Player HR DVS2U User Manual
Kalorik Grinder SUK PPG 26914 User Manual
Kenmore Gas Grill 1221613411 User Manual
Kenwood Speaker KFC 1271 User Manual
KitchenAid Dishwasher KUDD01DPPA User Manual
KitchenAid Double Oven 122 User Manual
KitchenAid Mixer K45SSAC 0 User Manual