Keys Fitness Treadmill 6200HR User Manual

TREADMILL  
MILESTONE 6200HR  
OWNER’S MANUAL  
KEYS Fitness Products, LP  
P.O. Box 551239  
Dallas, Texas 75239  
PART# 15-0108  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specification Sheet  
Horsepower (Continuous)  
2.5hp  
Display Type  
5 Window LED  
With green pace display  
Electronics  
One touch  
4
Pre-Set Programs  
Semi-Custom Programs  
User Programs  
Heart Rate Program  
Heart Rate Interactive  
Power Incline  
8
2
1
Yes  
12%  
Roller Diameter  
Cushioned Deck  
Speed Range  
2.5”  
Yes  
0-10mph  
20 x 60”  
Yes  
Belt Size  
Front Hand Rails  
Side Hand Rails  
Foot Print  
Yes  
29 x 71”  
10 Years  
2 Years  
1 Year  
Lifetime  
Warranty Motor  
Warranty Parts  
Warranty Labor  
Warranty Frame  
PAGE 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Information  
1) WARNING! Before using this treadmill or starting any exercise program, consult your physician. This is especially  
important for persons over the age of 35 and/or persons with pre-existing health problems. The manufacturer or distributor  
assumes no responsibility for personal injury or property damage sustained by or through the use of this product.  
2) WARNING! To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is  
important to review this manual and the following precautions before operation.  
SAFETY PRECAUTIONS AND TIPS  
It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar  
with warnings and safety precautions.  
This treadmill has a user maximum capacity of 350 pounds.  
The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not be  
placed in a garage, patio, or near water and should never be used while you are wet. KEYS recommends a treadmill  
mat be placed under the treadmill to protect floor or carpet and for easier cleaning.  
Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline  
wheels and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or  
frayed power cord.  
Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with  
bare feet, sandals, socks or stockings.  
Always straddle the belt and allow it to start moving before stepping onto the belt.  
Hold on to handrails when adjusting speed, incline, or other controls.  
Always examine your treadmill before using to ensure all parts are in working order.  
Allow the belt to fully stop before dismounting.  
Pets should never be allowed near or on the treadmill.  
Do not leave children unsupervised near or on the treadmill.  
Never operate the treadmill where oxygen is being administered, or where aerosol products are being used.  
Never insert any object or body parts into any opening.  
For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time.  
Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by  
an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow  
these instructions will void the treadmill warranty.  
Never leave the treadmill unattended while it is running.  
PAGE 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BeforeYou Start  
Thank you for purchasing a KEYS treadmill! This quality product you have chosen was designed to meet  
your needs for cardiovascular exercise.  
Before you start, please read the Owner’s Manual and become familiar with the operation of your new  
treadmill.  
Remember to take the time to perform the stretching exercises provided to avoid injury.  
Do not stand on the walking belt while pressing the Power button or Start/Stop button.  
Always adjust the speed of the treadmill in small increments as this treadmill is capable of high speeds.  
If you are taking medication, consult your physician to see if the medication will affect your exercise  
heart rate.  
If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the pre-set  
treadmill programs or start an exercise program without first contacting and receiving approval from your  
physician.  
To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console.  
KEYS recommends a sealed water bottle for beverages consumed while using the treadmill.  
Please review the following drawing below to familiarize yourself with the listed parts. This  
manual  
covers several treadmills, so the one pictured below may not be identical to your  
particular model.  
CONSOLE  
ELECTRONIC DISPLAY  
WATER BOTTLE HOLDER  
(WATER BOTTLE NOT INCLUDED)  
SIDE HAND RAILS  
MOTOR COVER  
WALKING BELT  
UPRIGHTS  
CIRCUIT BREAKER  
REAR ROLLER  
ADJUSTMENT BOLTS  
WHEEL  
FOOT RAILS  
PAGE 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warm Up Exercises  
EXERCISE GUIDELINES  
WARNING! Before beginning this or any exercise program, you should consult your physician. This is especially im-  
portant for individuals over the age of 35 or individuals with pre-existing health problems.  
Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the muscles and  
raising body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. The  
photos on this page show several forms of basic stretching you may perform before your workouts. In order to achieve  
an adequate warm-up, perform each stretch three times.  
TOE TOUCH STRETCH  
Stand bending your knees slightly and slowly bend for-  
ward from your hips. Allow your back and shoulders to  
relax as you reach down toward your toes as far as possi-  
ble. Hold for 15 counts, then relax. This will stretch your  
hamstrings, back of knees, and back.  
HAMSTRING STRETCH  
Sit with one leg extended. Bring the sole of the opposite  
foot toward you and rest it against the inner thigh of your  
extended leg. Reach toward your toes as far as possible.  
Hold for 15 counts, then relax. This will stretch your  
hamstrings, lower back, and groin.  
CALF/ACHILLES STRETCH  
With one leg in front of the other, reach forward and  
place your hands against a wall. Keep your back leg  
straight and your back foot flat on the floor. Bend your  
front leg, lean forward and move your hips toward the  
wall. Hold for 15 counts, then relax. To cause further  
stretching of the Achilles tendon, bend your back leg as  
well. This will stretch your calves, Achilles tendons, and  
ankles.  
QUADRICEPS STRETCH  
With one hand against a wall for balance, reach back and  
grasp one foot with your other hand. Bring your heel as  
close to your buttocks as possible. Hold for 15 counts,  
then relax. This will stretch your quadriceps and hip mus-  
cles.  
INNER THIGH STRETCH  
Sit with the soles of your feet together and your knees  
outward. Pull your feet toward your groin area as far as  
possible. Hold for 15 counts, then relax. This will  
stretch your quadriceps and hip muscles.  
PAGE 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly Instructions  
KEYS treadmills are shipped in one piece to make assembly easy. After opening the box,  
remove any packing materials from the treadmill. You should find a rear endcap (large  
plastic piece that fits over the rear roller area), and owner’s manual packet with bolts and  
screws for assembly. Do not throw away any packing materials until the unit is working  
properly. Place the base on a clean, level surface. Make sure the electrical cord will easily  
reach an electrical outlet.  
Figure 1 – Assembly for main uprights  
1) Have a second person raise the console to the upright position and hold.  
2) Insert 3/4” Button Head Bolt into upright bracket and tighten loosely. Repeat for  
opposite side.  
3) Insert the TUBE SPACER inside the upright frame and line up with the bottom  
hole. Hold tube spacer while inserting the 1 1/2” Button Head Bolt and lightly  
tighten. Repeat for opposite side.  
4) After completing opposite side, tighten all four assembled bolts and the two other  
button head bolts that were present before starting. Assembly is now complete.  
5) Be sure to insert the SAFETY KEY before turning the power on.  
Figure 2 – Assembly for rear end cap  
To attach the rear end cap:  
1) Place plastic rear end cap over exposed rear roller area.  
2) Align holes in plastic end cap with pre-drilled holes in frame.  
3) Loosely tighten each screw until all four screws are lined up.  
4) Tighten all four screws snugly.  
CAUTION: DO NOT OPERATE TREADMILL WITHOUT SECURING REAR  
ROLLER HOUSING!!!  
Be sure the treadmill is level to the floor. The rear feet can be adjusted to level the treadmill.  
Assembly is now complete!  
Figure 2  
Figure 1  
PAGE 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Power Requirements  
ARNG!  
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A  
RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF  
YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT  
MODIFY THE PLUG PROVIDED WITH THE PRODUCT IF IT WILL NOT FIT THE OUTLET. HAVE  
A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.  
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes,  
surges, and noise interference can result from weather conditions or from other appliances being turned on or off. To  
reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.  
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge  
protector with UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with UL suppressed voltage rating  
of 400V or less and an electrical rating of 120VAC, 15 amps.  
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance  
for electric current should the treadmill malfunction. This treadmill comes with an electrical cord with an equipment-  
grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge  
protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and  
ordinances.  
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in  
the drawing below.  
PAGE 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Console Functions and Descriptions  
There are five display windows on the control panel to provide feedback information.  
WORKOUT TIME/PACE WINDOW  
TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds)  
INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to  
0 seconds  
PACE: Indicates amount of time required to complete 1 mile at current speed.  
SPEED WINDOW  
SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments  
DISTANCE / CALORIES WINDOW  
DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at  
10.0  
CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and  
time  
INCLINE WINDOW  
INCLINE: Indicates incline in percent of grade 0-12% in 0.5 increments  
CENTER BRICKYARD WINDOW  
Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode, shows  
the change in speed profile across the interval range (1-10) and shows position with a blinking action.  
CALORIE/DISTANCE WINDOW  
CENTER BRICKYARD WINDOW  
TIME WINDOW  
INCLINE WINDOW  
SPEED WINDOW  
PAGE 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Program and Operating Instructions  
QUICK START / MANUAL MODE  
Plug into a surge protector outlet. Insert the Safety Key into the treadmill console.  
Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.  
Press POWER button. There will be an eight (8) second delay after pressing the POWER button before  
data can be entered. The TIME window will flash.  
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt  
starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease)  
button.  
To end your workout, press START/STOP button. Belt will gradually slow to zero.  
To pause your workout, press PAUSE.  
To re-start after pausing: Press the PAUSE button. WARNING: THE TREADMILL BELT WILL  
RESUME AT THE SPEED THE TREADMILL WAS MOVING BEFORE PAUSING.  
Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to getting  
started. After pressing the POWER button, the time window will blink. Use the SPEED/TIME + or –  
arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED/TIME  
window will now be flashing. Using the same + or – arrows, select the speed for your workout, then press  
ENTER PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or – arrows to  
set your workout incline, then press ENTER PROGRAM. To start, press the START/STOP button.  
ENTER  
POWER  
START/STOP  
PAUSE  
SPEED/TIME  
INCLINE  
PAGE 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Program and Operating Instructions  
PROGRAM MODE  
Plug treadmill into a surge protector outlet . Insert the Safety Key into the treadmill console.  
Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.  
Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME window  
will flash.  
There are four (4) pre-set and eight (8) semi-custom pre-set programs on the MS6200HR. The treadmill  
includes FAT BURN, CARDIO, WARM-UP, and CROSS TRAINING programs. Select the program by  
pressing the appropriate button.  
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts  
moving.  
CUSTOMIZING PROGRAMS in P1 and P2 Mode: Each pre-set program(Fat Burn, Cardio, Warm-up, Cross  
Training) can be customized in the P1 or P2 mode. After making the program selection, the Calorie window will  
read “OP”. The “OP” refers to “original program” and is preset. The program name you select will display in  
the diode light beside the program name. Press the same program button once more and the Calorie window will  
read P1. The “P1” mode is now accessed. You can now program the Time, Speed, and Incline in P1 mode,  
which will be saved for future workouts.  
1) The TIME window will blink. Use the SPEED/TIME + or – arrows to select your workout time. Press  
ENTER PROGRAM.  
2) The SPEED/TIME window will then blink. Use the same + or – arrows to select the speed for your workout.  
Press ENTER PROGRAM.  
3) The INCLINE window will then blink. Use the INCLINE + or – arrows to set your workout incline. Press  
ENTER PROGRAM.  
To start, press the START/STOP button. To access P2 mode, press the selected program button three times (once  
for OP, twice for P1, three times for P2). Follow the above steps 1-3 to customize P2 settings.  
TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed  
the P1 or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For  
instance to change to a new setting in P1-FAT BURN, press the FAT BURN button twice to access P1. Then  
press the PAUSE button to get the TIME window to flash. Follow the directions above to continue to change the  
program.  
DIODE PROGRAM LIGHTS  
FAT BURN  
POWER  
POWER  
CARDIO  
START/STOP  
WARM UP  
PAUSE  
USER PROGRAM  
ENTER PROGRAM  
IN-  
CROSS TRAINING  
SPEED  
PAGE 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Program Instructions Heart rate  
See page 13 for pictures and diagrams  
HEART RATE MONITOR MODE  
The treadmill may at any time be used in the Heart Rate Monitor Mode. If the signal from the chest  
strap is detected, heart rate BPM will be displayed in the INCLINE window. The incline will only be  
briefly displayed if manual or program changes are initiated. The Heart Rate program is designed to keep  
your heart at a desired amount of “beats per minute” by automatically adjusting the incline. For example,  
you have programmed in a desired heart rate of 125 BPM and your heart rate is only at 110 BPM. If you  
are wearing the Heart Rate Transmitter, correctly the incline will automatically increase to intensify the  
work load, causing your heart rate to slowly climb to 125 BPM. The treadmill will attempt to maintain  
your target heart rate through adjustments to the incline for the remainder of your workout. In the same re-  
spect, if your heart rate is above your programmed amount of BPM’s, the incline will automatically de-  
crease to lower your heart rate. You may at any time during the Heart Rate Program adjust/override the  
speed and/or the incline by simply pressing the correct corresponding button. You may also change your  
“Target Heart Rate” at any time by pressing the TARGET UP or TARGET DOWN button.  
HEART RATE PROGRAM OPERATION  
Plug treadmill into a surge protector outlet. Insert the Safety Key into the treadmill console.  
Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.  
Press POWER button. Place the Heart Rate Transmitter strap across your chest and connect ends.  
(Make sure your skin is moist and the strap is snug for accurate transmission). At this time, if the dis-  
play is receiving a signal from the chest strap, the incline window will begin to settle on your current  
heart rate.  
Press the HEART RATE CONTROL button to enter the electronics into the Heart Rate Program. The  
incline window will momentarily flash ‘125’, which is the default program target heart rate.  
The TIME window will blink. Use the SPEED/TIME + or – arrows to select your workout time. Press  
ENTER PROGRAM.  
The SPEED/TIME window will then blink. Use the same + or – arrows to select the speed for your  
workout. Press ENTER PROGRAM.  
The incline window (if receiving your heart rate accurately) will show current BPM, and the small red  
light labeled PULSE adjacent to the incline window, will be illuminated. (If the receiver is not receiv-  
ing an accurate reading, the incline window will be flashing - - - -).  
To adjust the pre-set target heart rate press the TARGET +/TARGET– button then press the ENTER  
PROGRAM button.  
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt  
starts moving.  
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt  
starts moving.  
The small light at the top of the console labeled TARGET will be illuminated if you are at your target.  
If you are not, the arrow shaped lights will illuminate and reflect if you are above or below your goal. If  
you are not within 25 BPM of your “Target heart rate” the program will not work. DO NOT STOP TO  
START OVER. Continue exercising and your heart rate will naturally increase. The program will continu-  
ally monitor your heart rate and periodically adjust the incline up or down to increase or decrease the resis-  
tance thereby keeping you at your target zone. At the conclusion of the programmed time the TIME win-  
dow will flash 00:00 and the CALORIES/DISTANCE window will continue to accumulate values. The  
treadmill will continue operation until the START/STOP button or the PAUSE button is pressed. Press the  
POWER button to turn off the treadmill.  
PAGE 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Program Instructions Heart rate Mode  
TARGET ARROWS  
TIME  
CALROIES/DISTANCE  
TARGET UP  
POWER  
TARGET DOWN  
POWER  
START/STOP  
PAUSE  
INCLINE WINDOW  
HEART RATE CONTROL  
ENTER PROGRAM  
PAGE 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Program Profiles  
SPEED  
SPEED  
12  
11  
12  
11  
10  
9
8
7
6
5
4
3
INCLINE  
INCLINE  
10  
9
8
7
6
5
4
3
2
1
2
1
1 2 3 4 5 6 7 8 9 10  
1 2 3 4 5 6 7 8 9 10  
The Cardio Program is designed to  
vary the treadmill Speed, while  
maintaining a constant Elevation.  
The Fat Burn Program is designed  
to vary the treadmill elevation, while  
maintaining a constant walking belt  
speed.  
SPEED  
SPEED  
12  
11  
10  
9
8
7
6
5
4
3
12  
11  
10  
INCLINE  
INCLINE  
9
8
7
6
5
4
3
2
1
2
1
1 2 3 4 5 6 7 8 9 10  
1 2 3 4 5 6 7 8 9 10  
The Warm Up Program is designed to  
gradually increase the treadmill Speed and  
Elevation in the first segment (warm up)  
and gradually decrease the treadmill Speed  
and Elevation in the last segment (cool  
down). This is also known as a  
The Cross Training Program is designed to  
control the walking belt speed and elevation  
inversely in alternating segments.  
Plateau program.  
PAGE 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Belt Adjustment and Tension  
WARNING! Do not overtighten rollers! This will cause  
premature roller bearing failure!  
Belt adjustment and tension performs two functions: adjustment for  
tension and centering. Your new treadmill comes pre-adjusted from  
the factory for tension and centering. Please follow the procedures  
below if the belt shifts to the left or right while walking:  
WALKING BELT IS SHIFTING TO THE LEFT (Diagram 1)  
First, turn treadmill on to run at 1 mph. Using the hex key provided,  
turn the left rear roller adjustment bolt ¼ turn in the clockwise  
direction. Next, run the treadmill at 2.5 mph. You should see the belt  
start to correct itself by moving back towards the center. Repeat the  
above procedure until the walking belt is centered. It may be  
necessary to set walking belt tension once you have completed this  
procedure if the belt feels like it is slipping while walking. Refer  
below to the “Walking Belt Slipping” instructions.  
WALKING BELT IS SHIFTING TO THE RIGHT (Diagram 2)  
First, turn the treadmill on to run at 1 mph. Using the hex key  
provided, turn the right rear roller adjustment bolt ¼ turn in the  
clockwise direction. Next, run the treadmill at 2.5 mph. You should  
see the belt start to correct itself, moving back towards the center.  
Repeat the above procedure until the walking belt is centered. It  
may be necessary to set walking belt tension once you have  
completed this procedure if the belt feels like it is slipping while  
walking. Refer below to the “Walking Belt Slipping” instructions.  
WALKING BELT IS SLIPPING DURING USE (Diagram 3)  
First, unplug the power cord from the surge protector. Using the  
hex key provided, turn both left and right rear roller adjustment bolts  
the same distance, usually a ¼ turn in the clockwise direction. Plug  
the power cord back into the surge protector and run the treadmill at  
2.5 mph. You should now walk on the belt to determine if the belt is  
still slipping. Repeat the above procedure until the walking belt is  
not slipping. The tension should be just tight enough not to slip.  
Turning the hex key counter clockwise brings the rear rollers  
and belt towards you.  
Turning the hex key clockwise pushes the rear roller and belt  
away form you.  
PAGE 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Change Miles per hour to Kilometers per hour  
Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). All  
treadmills are calibrated at the factory for British Units (miles per hour). To change the display to read in  
kilometers, follow the steps described here:  
1) Turn power OFF on the console. (Do not unplug treadmill) Attach the magnet safety key to the console.  
2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in the backside  
of the console (see diagram below).  
3) Depressing the calibration mode switch ONCE; CL11 should appear in the TIME window.  
4) Pressing the SPEED +/- button will activate your choice.  
5) To accept the setting, press the POWER button.  
Page 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Guide  
Treadmill will not start.  
1) Is the Safety Key inserted into the treadmill Console?  
2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged  
into a properly grounded outlet, and the surge protector is turned on. (Refer to “Power  
Requirements” on page 8)  
3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has  
tripped. Wait five minutes and then press the switch back in.  
4) Check the house electrical breaker box and the circuit breaker for the room where the  
treadmill is located. If it has tripped, reset or have an electrician replace the breaker in  
home.  
5) Have an electrician check for inadequate voltage at the outlet.  
Treadmill loses power during use.  
1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has  
tripped. Wait five minutes and then press the switch back in.  
2) Check the house electrical breaker box and the circuit breaker for the room where the  
treadmill is located. If it has tripped, reset or have an electrician replace the breaker in  
home.  
3) If the treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.  
Treadmill walking belt slows during use.  
1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector,  
rated at 15 amps, with a 14-gauge cord of five feet or less and the surge protector is securely  
plugged into the outlet.  
2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.  
Treadmill walking belt slips or is not centered on rear roller.  
1) Refer to “Belt Adjustment and Tension” section on page 15.  
2) Need help? Call Keys Technical Service at (888) 340-0482.  
Treadmill Error Messages.  
Your treadmill is equipped with a software package that enables error messages to be displayed  
when there is a problem. To avoid possible damage to the treadmill and the possibility of  
injury, do not operate the treadmill until the problem is corrected. Call Keys Technical  
Service at (888) 340-0482.  
Page 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts & Diagrams  
Part #  
Part #  
1
2
Left Side Extrusion Rail  
Right Side Extrusion Rail  
Treadmill Belt  
05-0031  
05-0031  
04-0020  
24-0174  
09-0020  
03-0015  
06-0143  
06-0143  
10-0006  
various  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
Front Wheel (2)  
Uprights for Console (2)  
Motor Hood Cover Top  
Motor Drive Belt  
Motor  
06-0039  
various  
06-0146  
04-0004  
12-0033  
12-0022  
24-0175  
08-0112  
various  
08-0027  
08-0115  
3
4
Front Roller Assembly  
Rear Roller  
5
6
Treadmill Deck  
Elevation Motor (acuator)  
Console Assembly  
Membrane  
7
Left End Cap  
8
Right End Cap  
9
Rear Adjustable Foot (2)  
Main Frame  
Handlebars  
10  
11  
Toggle switches (2)  
Bottom Motor Pan  
06-0145  
Lower Electronics M/  
Control P/Supply  
Page 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Milestone 6200HR Parts List  
PART #  
02-0004  
02-0005  
02-0006  
02-0007  
02-0008  
02-0009  
02-0013  
02-0014  
02-0015  
02-0016  
02-0017  
02-0018  
02-0020  
02-0021  
02-0022  
02-0024  
02-0027  
02-0031  
02-0033  
02-0036  
02-0038  
02-0040  
02-0042  
02-0050  
02-0053  
02-0054  
02-0068  
02-0082  
02-0092  
02-0099  
02-0103  
02-0105  
02-0113  
02-0123  
02-0133  
02-0136  
02-0137  
02-0140  
02-0141  
03-0015  
04-0004  
04-0020  
05-0031  
06-0014  
06-0016  
06-0145  
06-0021  
06-0024  
06-0039  
06-0058  
06-0071  
06-0084  
06-0117  
DESCRIPTION  
SCREW-8x5/8 PHIL PH AB BLACK  
SCREW-8x5/8 PPH HILO BLACK TPB  
BOLT-HEX 5/16-18x5 1/2 GRADE 5-ZP  
NUT 5/16-18 NYLOCKZP  
QTY PART #  
DESCRIPTION  
QTY PART #  
DESCRIPTION  
QTY  
2
24 08-0106  
LIMIT SWITCH  
1
1
1
2
1
1
1
1
1
2
1
2
8
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
1
1
7
2
2
2
2
1
1
1
19-0074  
19-0076  
19-0161  
20-0103  
20-0104  
20-0105  
20-0108  
21-0048  
21-0049  
21-0051  
21-0052  
21-0053  
22-0058  
22-0077  
22-0078  
22-0079  
23-0103  
23-0104  
23-0105  
24-0174  
24-0175  
26-0085  
15-0108  
16-0070  
07-0027  
19-0159  
BRKT-ACTUATOR MOUNTING  
BRKT-CONTROLLER  
8
1
3
3
3
8
9
4
1
2
2
2
2
4
2
8
1
1
1
2
1
1
1
2
1
2
2
7
1
4
2
1
1
08-0112  
08-0004  
08-0027  
08-0047  
08-0077  
08-0115  
09-0020  
09-0019  
10-0006  
10-0017  
10-0020  
10-0023  
10-0024  
11-0002  
11-0023  
12-0022  
12-0033  
13-0003  
13-0011  
13-0014  
13-0017  
13-0042  
13-0046  
14-0028  
14-0053  
14-0054  
14-0205  
14-0289  
14-0321  
14-0327  
14-0337  
14-0347  
14-0356  
17-0073  
17-0030  
17-0061  
17-0074  
17-0075  
17-0076  
17-0077  
17-0079  
17-0080  
18-0008  
MEBRANE LED FOR WEDGE CONSOLE  
BREAKER-CIRCIT-15AMP  
1
PLATE CONSOLE WEDGE  
PROC FRAME 17-0074  
1
SWITCH-REMOTE-W/HARNESS  
ENCODER-OPTICAL-ALEPH  
CORE-ERRITE  
1
BOLT-HEX 5/16-18x3/4 GRADE 2-ZP  
NUT-HEX 5/16 WIZ-FL-LK-ZP  
WASHER LOCK 1/4"  
PROC RT U/R 17-0061  
1
PROC LT U/R 17-0061  
1
CONTROLLER 08-0050 W/OUT SWITCH  
ROLLER REAR 2.5"x24.5" CONV/FOLD  
FROLLER FRONT 2.5x24.5" CONV  
TIP-CRUNCH 1" CNV  
PROC BENT H-BAR 17-0080  
ACTUATOR X-TB CORNERS CLIPPED  
STIFFNER-NOTCHED  
2
BOLT-HEX 1/4-20x2 1/2" GRADE 5 ZP  
WASHER SPRING  
1
1
BOLT-HEX 3/8-16x2 1/2" GRADE 5  
NUT-NYLOCK HEX 3/8-16  
FRAME BRACE PUNCHED  
INSIDE 90 DEGREE BEND CTRL BRKT  
INSIDE CT 17-0079  
1
TAPE-FOAM-1"X75ft  
1
NUT-PUSH 3/8 HAT BLACK 375012  
SCREW SHCS 1/4-20x2 1/2"  
WASHER 9/32 5/8 1/8THICK ZP  
NUT-NYLOCK HEX 10-24  
GRIP MOLDED ROUND  
1
BOARD ISOLAORS 17/32" SHORT  
TAPE-ADHESIVE 1'X108' ST567  
BUSHING-REAR ELEVAION  
FLYWHEEL 1.125 10MPH FOR 2.5 ROLLERS  
ACTUATOR 40LB-MAYTECH  
MOTOR MCM BLK CHROME 2.5HP  
HARNESS-ENCODE  
ELEVATION BRKT & ROD  
ACTUATOR X-TB SUB-ASSEMBY  
U/R SB ASSEMBLY  
2
1
1
CARRIAGE BOLT 5/16x1 GRADE 5 ZP  
NUT-T HF 14209H-DB  
DECK FRAME SUB-ASSEMBLY  
FRONT EVEL ASSEMBLY-CONV  
DECK FRM & REAR LEG ASSEMBLY  
U/R ASSEM W/STIFFNER TUBE WEDGE  
FRONT ROLLER ASSEMBLY  
CONSOLE ASSEMBLY MS6200HR  
INST PACKET MS6200HR  
1
1
BOLT-HEX 3/8-16x1 3/4" GRADE 5ZP  
WASHER-#10 EXTERNAL STAR  
SCREW-PPH 8x5/8 GREEN HEAD  
WRENCH-ALLEN 3/16 SHAFT ARM  
RETAINER-GUIDE TUBE  
1
1
CORD-POWER-90"  
1
WIRE-JUMPER 12"-220V-KEYS SERIES  
HARNESS-TELCO-HRC  
1
1
SCREW#8x5/8' SD BLACK  
HARNESS-KILL SWITCH SM9.3  
HARNESS CONTROLLER 80"  
DECAL-CIRCUIT BREAKER ALL  
DECAL-SINCLINE REMOTE  
DECAL-SPEED REMOTE  
INST MANUAL MS6200  
1
NUT-NYLOCK HEX 1/4-20  
BOX ASSEMBY MS6200  
1
SCREW-SHCS 1/4-20x3/4"  
ELECTRONICS-LCD-4 WIN-HOR-REV  
BRK MOTOR SUPPORT REVISED 19-0005  
1
SCREW-HWH MACH 8-32x3/8"  
WASHER-FLAT SAE 5/16  
2
SCREW-BUTTON HEAD 5/16-18x2 1/2'  
SCREW-PHTR #8x3/" AB BLACK  
WASHER -SFW 3/8X7/8X1/8" THICK  
BOLT-CARRIAGE 10-24x3/4'  
INDRTY-5/16-18 HEAVY WAL AVK  
SCREW-HWH SLOTTED 8-18x3/4' AB ZP  
WASHER-FENDER 1/4x1"  
DECAL DISCONNECT-MOTOR COVER  
STICKER HEART RATE ACUMEN  
DECAL-10YR MOTOR WARRANTY  
OVERLAY CONSOLE MS6200HR  
DECAL MOTOR COVER MS4200/6200  
DECAL OPERATION WEDGE CONSOLE  
STICKER 2.5HP  
NUT RIV 5/16-18 AVAKALS4-518-150  
TETHER KILL PIN  
RECT 1x2x12GAx24.5  
1
2
2
6
1
1
1
2
1
RECT 1x1x18GAx3 PUNCHED  
RECT 11/2x4x16GAx42 3/4"  
RECT 1x3x16GAx165  
PLUG PUSH-IN  
SCREW PPH#4x5/8' TYPE AB  
PUSH NUT BLACK.112 SHAFT  
WALKBOARD KORETRON 60"CONV  
BELT POLY V-190J8  
SQ 1x1x18GAx25.44  
RECT 1x2x14GAx25.44  
RECT 1x3x16GAx28.44  
WALKBELT 1PLY 19.75x122.75 CONV  
EXTRUSION LT&RT SIDE BRD CONV GRAY  
BUSHING-STRAIN RELIEF #1237  
TIES-WIRE  
RND 0.5x18GAx100(CUT 32PCS)  
RND 1.5x16GAx19H-BAR  
ROD 3/8x1 1/2"  
11 19-0184  
BRKT HEART RATE REC FOR WEDGE  
BRACKET-MOTOR COVER  
GUIDE BELT GLAVANIZED  
BRKT-UNIVERSAL  
PAN-END-BASE  
1
1
2
2
4
2
1
2
19-0015  
19-0019  
19-0023  
19-0177  
19-0106  
19-0134  
19-0147  
19-0187  
CLAMP WIRE 3367 7/16  
CLIP-ALLEN WRENCH  
WHEEL-KEYS SERIES-2.5"  
BRKT CHANNEL SUPPORTS  
BRK-LOWER ELEV GUSSET  
BRACKET-BASE ELEVATION  
BRKT FRONT ELEV-REWORK 19-0075  
BRKT FRONT ELEV REVISED  
SUPPORT PC BOARD-HRC  
FAN 5"-5/8" ID  
BAG-PLASTIC 12x12 3MIL-INST PACKET  
SWITC HOUSING ROUND GRAY  
06-0139  
06-0140  
06-0142  
06-0143  
06-0144  
06-0145  
06-0146  
07-0020  
07-0050  
07-0041  
TETHER HOUSING FOR WEDGE CONSLE  
INSERT LED FOR CONSOLE  
CONSOLE WEDGE GRAY  
END CAP DUAL GRAY  
PULLEY DRIVE 2.5" 8 GROOVE  
BOTTOM PAN CONV  
COVER FRO MOTOR CONV GRAY  
RECEIVER DISCRETE-LED-HRC  
ELECTRONICS 5 WIN LED GREEN  
CHEST STRAP NO LOGO ALL HR UNITS  
1
1
1
1
1
1
1
1
1
1
19-0105  
19-0159  
19-0007  
19-0073  
19-0077  
19-0079  
19-0143  
19-0144  
19-0155  
19-0156  
BRKT-REAR LEG COVER  
BRKT MTOR SUPPORT REVISED 19-0005  
BRKT-MTOR TENSION  
BRKT-ELEVATION PIVOT  
BRACE-CNTROLLER FRONT ELEVATION  
BRKT-BELT GUIDE  
BRKT-LEFT STRAIGHT U/R  
BRKT RIGHT STRAIGHT U/R  
BRKT FRON RLLER 2 1/2  
2
2
1
2
1
2
1
1
2
2
BRKT REAR OLLER 2 1/2  
Page 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Keys Milestone 6200HR Treadmill KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTY  
PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.  
This Limited Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the  
KEYS brand name. The warranty period on the MILESTONE 6200HR to the original purchaser is (lifetime) on the frame, (10) years on the motor, (2) years parts, and (1)  
year labor.  
Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller is free from defects in materials or workmanship  
under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your proof of the date of purchase. This warranty only extends to you, the original purchaser. It is not  
transferable to anyone who subsequently purchases the Product from you. It excludes expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Keys Fitness  
authorized dealer/technician unless otherwise authorized by Keys Fitness in writing (if anyone other than a Keys Fitness authorized dealer/technician assembles a Keys Fitness treadmill the warranty will be void unless  
accompanied by written authorization by Keys Fitness).  
During the warranty period Keys will at no additional charge, repair or replace (at Keys’ option) the product if it becomes defective, malfunctions, or otherwise fails to conform with this Limited Warranty  
under normal non-commercial, personal, family or household use. In repairing the Product, Keys may replace defective parts, or at the option of Keys, serviceable used parts that are equivalent to new parts in  
performance. All exchanged parts and Products replaced under this warranty will become the property of Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty.  
To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts determined to be defective must be returned to  
Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product. In addition, you are responsible  
for insuring any parts or Product shipped or returned. You assume the risk of loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of  
alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty.  
This warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does not extend to any Product that has been damaged or rendered  
defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or  
(e) as a result of service by anyone other than Keys, or an authorized Keys warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any  
Product be submitted for warranty service be found ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Keys’ receipt of payment or acceptable arrangements  
for payment.  
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED  
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL BE  
RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE  
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty  
gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to  
assume for it any other express warranty.  
PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR TREADMILL  
WITH KEYS FITNESS PRODUCTS, LP. MADE IN THE USA. Thank you for your business! PLEASE MAIL WARRANTY CARD TO:  
KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355.  
KEYS FITNESS TREADMILL WARRANTY REGISTRATION  
TELEPHONE  
LAST  
M.I.  
FIRST  
ADDRESS  
CITY  
APT. NO.  
ZIP  
STATE  
SERIAL NO.  
DATE OF PURCHASE  
MODEL NO.  
How important are each feature:  
Least  
Unique Features  
Horsepower  
Warranty  
Price  
Other Comments:  
_______________  
Where did you learn about treadmills?  
TV____ Radio____ Friend____  
Name of store or company where  
purchased:  
Most  
_______________  
_______________  
_______________  
In Store Display____ Salesperson___  
Print ad/flyer____ Internet______  
How do you plan to use the treadmill?  
Walk____ Run_____ Both_____  
Look/Design  
Folding Feature  
Who will use the treadmill?  
Male____ Female_____ Both_____  
Why did you purchase a treadmill?  
KEYS FITNESS respects the rights of your privacy. Our company  
will not sell or distribute to others the information above. This  
information is used to track our product quality and to contact you in  
the event of a product safety concern. It may be used to offer you  
future Keys products only through the mail. Please check here if wish  
not to receive any additional information on Keys products.  
Dr.’s Orders____ Loose Weight____  
In-home convenience____  
Improve Cardiovascular Fitness___  
Safety from outdoors____  
How many family members? _____  
AGE:  
15-24____ 25-34____  
35-44____ 45-54____  
55-64____ 65 +_____  
Other __________________________  
Page 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Infinity Vacuum Cleaner NV30CN User Manual
InFocus Pet Fence IN1110a User Manual
Insignia Car Amplifier NS A1000 User Manual
Intel Computer Hardware Motherboard User Manual
Invacare Mobility Aid 1038599 User Manual
JBL Car Speaker P 422 User Manual
JBL Home Theater System ATX100S User Manual
JVC Blu ray Player LT 42B300 User Manual
KitchenAid Coffee Grinder 4KPCG100PM0 User Manual
Kompernass Oven KH 1138 User Manual