Owner’s Manual
International
Bench
Customer Service
(888) 340-0482
4009 Distribution Drive
Suite 250
Garland, TX 75041
SERIAL TAG IS LOCATED ON THE FRAME
Model Name: ST-IB
Date of Purchase:
215-00219
08/07 Rev A
Serial Number:
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
Please read all instructions carefully before using this product.
SAFETY TIPS
Consult with your physician before engaging in any vigorous exercise. Know your heart rate
and/or pulse as well as your physician-recommended heart rate training zone. Proper medical
clearance is recommended for anyone beginning an exercise program especially if you are 35
years of age or older or suffer from heart respiratory problems.
- Warm-up before any exercise program with 8 minutes of aerobic-like activity followed
by stretching from head to toe.
- Wear comfortable clothes that allow freedom of movement and are not tight or
restricting.
- Wear comfortable shoes made with good support and non-slip soles.
- Breathe naturally, never holding your breath during an exercise.
- Perform exercises consistently with proper technique and pass through a full range of
motion.
- Increase resistance by adding heavier weights. Decrease resistance by using lighter
weights.
- Always use a spotter for safety.
- Avoid over-training. You should be able to carry on a conversation while exercising.
- After an exercise session. Cool down with slow stretching, cycling or walking.
EXERCISE DEFINITIONS:
Sets: A set is one complete routine of exercises. Complete 1-3 sets for each exercise.
Repetitions: (referred to as reps) Is the number of times you perform an exercise in a row.
We recommend beginning with 6 reps and increasing up to 12 reps as indicated below.
Novice: Start with one set of 8-12 reps. Once you can complete the entire set of 12 reps con-
secutively, progress to the intermediate level.
Intermediate: Complete 2 sets of 8-12 reps once you can complete two sets of 12 reps con-
secutively, progress to the advanced level.
Advanced: Complete 3 sets of 12 reps
DISCLAIMER:
Keys Fitness is not responsible for the misuse of any of its products or for any injury sustained
while using any Keys Fitness product. The consumer uses any or all of Keys Fitness products at
their own risk.
WARNING!
1) The max user weight limit for this unit is 300 pounds.
2) The max total weight limit for this unit is 600 pounds (user weight + lifting weight).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Thank you for purchasing the Strength Trainer International Bench! The quality product you
have chosen was designed to meet your needs for cardiovascular exercise. Before you start,
please read the Owner’s Manual and become familiar with the operation of your new unit.
Remember to take the time to perform stretching exercises, provided in this manual, to help
avoid injury.
Getting Started - The Strength Trainer International Bench will require some assembly.
Unpack the box in a clear area. Remove packing material. Do not dispose of packing mate-
rial until assembly is complete and unit is working properly. Place the unit on a clean level
surface for assembly. Before assembling, the unit should be placed as close as possible to its
final location. If you are missing any parts or hardware, please call Keys Fitness at 1-888-340-
0482. Tools have been provided to assist with product assembly. Keys Fitness recommends for
two people to assemble the unit. As you assemble the bench, make sure all parts are oriented
as shown in the drawings.
The included hex key, grease packet, and the following tools (not included) are recommended
for assembly.
Hex Key (Included)
Two Adjustable Wrenches
Rubber Mallet
Weight Rest
Flat Head Screwdriver
Phillips Head Screwdriver
Adjustable Tube
Safety Spotter
Arm Curl Pad
Leg Extension
Weight Plate Holder
w/ Curl Bar
Olympic Adapter
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Hardware Identifier
See the drawings below to identify the hardware used in the assembly. The number in paren-
theses is the reference number of the part.
Note: Some hardware may be pre-installed in some parts.
M6 x 20mm
Screw (41)
M8 x 60mm Bolt (59)
M8 x 10mm
Set Screw (60)
M6 x 40mm Screw (48)
M10 x 60mm Carriage Bolt (29)
M8 x 65mm Bolt (46)
M4 x 16mm
Screw (57)
M10 x 65mm Bolt (30)
M8 x 70mm Bolt (71)
M10 Washer (43)
M8 Washer (50)
M6 Washer (54)
M10 x 70mm Bolt (33)
M10 x 70mm Bolt Set (55)
M10 Nylon Locknut (58)
M8 Nylon Locknut (49)
M10 x 95mm Bolt (64)
M10 x 120mm Bolt (14)
M10 x 145mm Bolt (53)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 1
Insert four M10X60mm carriage bolts (29) up through the bottom of the right stabilizer (2).
Attach the right upright (4) to the right stabilizer (2) with indicated carriage bolts and nylon
locknuts (58).
Repeat to complete the assembly of the left stabilizer (1) and left upright (3).
Note: Make sure the recessed areas around the holes on stabilizers are on the bottom.
Figure 1
4
2
58
3
58
1
29
29
Recessed Areas
NOTE
:
Hand tighten bolts and nylon nuts until machine is fully assembled.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 2
Attach the crossbar (5) to the right upright (4) using two M10X120mm bolts (14), an upright
plate (15), and two M10 nylon locknuts (58).
Repeat to complete the assembly for the left upright (not shown).
Figure 2
4
58
1 4
15
5
14
Step 3
Attach the right rear support (7) to the right stabilizer (2) using the indicated M10X60mm car-
riage bolts (29), two washers (43), and two M10 nylon locknuts (58).
Secure the right rear support (7) to the right upright (4) using two M10X65mm bolts (30), two
M10 washers (43), and two M10 nylon locknuts (58).
Repeat to complete the assembly for the left side (not shown).
Figure 3
58
4
7
58
43
58
29
30
2
NOTE
:
Hand tighten bolts and nylon nuts until machine is fully assembled.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 4
Attach the front leg (12) to the front stabilizer (11) with two M10X95mm bolts (64) and two
M10 nylon locknuts (58).
Figure 4
12
58
64
11
Step 5
Position the frame (8) so that the hexagonal holes are on the bottom. Attach the frame (8)
to the crossbar (5) using three M10X70mm bolts (33), two M10 washers (43), and three M10
nylon locknuts (58).
Figure 5
43
58
3 3
43
33
5
58
33
8
Hexagonal
Holes
NOTE Hand tighten bolts and nylon nuts until machine is fully assembled.
:
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 6
Tighten the "T"-handle (45) into the seat carriage (42). Pull the "T"-handle (45) out as far as
it will go and slide the seat carriage (42) onto the frame (8).
Attach the front leg (12) to the frame (8) using two M8X60mm bolts (59), two M8X65mm bolts
(46), six M8 washers (50), and four M8 nylon locknuts (49).
Figure 6
59
50
49
50
45
8
12
50
42
50
46
49
Step 7
Set the pins on the adjustment tube (9) into a set of brackets located on the left and right
uprights (3 & 4).
Figure 7
Pin
4
9
Pin
3
NOTE
:
Hand tighten bolts and nylon nuts until machine is fully assembled.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 8
Attach the tether on the seat adjustment pin (40) to the seat frame (10) using an M4X16mm
screw (57).
Attach the seat pad (21) to the seat frame (10) with four M6X20mm screws (41).
21
Figure 8
57
40
1 0
41
41
Step 9
Attach the backrest pad (22) to the two backrest frames (17) with four M6X40mm screws (48)
and four M6 washers (54).
Note: Do not fully tighten the screws yet.
22
Figure 9
54
54
48
54
54
17
48
NOTE
:
Hand tighten bolts and nylon nuts until machine is fully assembled.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 10
Apply a small amount of grease (included) to an M10X145mm bolt (53). Attach the seat frame
(10) and the backrest frames (17) to the seat carriage (42) using the M10X145mm bolt (53),
two M10 washers (43), and an M10 nylon locknut (58).
Note: 1) The seat pad (21) has been removed from the drawing to clarify the installation to
the seat carriage (42). 2) Do not overtighten the nylon locknut, the seat and backrest frames
must pivot easily.
Insert the seat adjustment pin (40) through the seat frame (10) and tube located on the seat
carriage (42).
Tighten the four M6X40mm screws (48) that were installed in Step 9.
Figure 10
58
43
43
40
10
53
Grease
42
T ube
Step 11
Attach the weight tube (19) to the leg lever (18) using an M8X70mm bolt (71), two M8 wash-
ers (50), a 17mmX9mm spacer (61), and a M8 nylon locknut (49).
Place the 25mm round outer cap (62) onto the end of the weight tube (19).
Figure 11
1 8
62
50
49
5 0
61
7 1
19
NOTE
:
Hand tighten bolts and nylon nuts until machine is fully assembled.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 12
Apply grease to the barrel of the M10X70mm bolt set (55). Next, attach the leg lever (18) to
the front leg (12) and secure using the bolt set (55). Make sure the barrel of the bolt set (55)
is inserted through both sides of the bracket on the front leg (12).
Note: Do not overtighten the bolt set; the leg lever must pivot easily.
Figure 12
55
Grease
18
Bracket
12
Step 13
Insert a pad tube (24) into either hole on the front leg (12). Slide a foam pad (23) onto each
end of the pad tube (24).
Insert a pad tube (24) into a hole on the leg lever (18). Slide a foam pad (23) onto each end
of the pad tube (24). Press a pad cap (68) into each end of the tube.
Note: It is recommend you use a rubber mallet to gently hammer the caps into place.
Repeat for other pad tube (24).
Figure 13
23
23
18
68
24
24
12
23
68
NOTE
:
Hand tighten bolts and nylon nuts until machine is fully assembled.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 14
Insert a weight rest (39) into the right upright (4) and secure by engaging the locking bar
around the upright.
Insert a safety spotter (27) into the right upright (4) and secure by engaging the locking bar
around the upright.
Repeat for left side.
Figure 14
39
Locking
Bar
4
27
Step 15
Attach the curl pad (20) to the curl post (13) using two M6X20mm screws (41).
Figure 15
2 0
13
41
NOTE
:
Hand tighten bolts and nylon nuts until machine is fully assembled.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Step 16
Attach a curl bumper (66) to curl bar (31) using a M4X16mm screw (57).
Attach the curl bar (31) to the leg lever (18) and secure with the curl bar pin (28). Next,
attach the tether on the curl bar pin (28) to the leg lever (18) using a M4X16mm screw (57).
Figure 16
31
66
57
18
57
28
Step 17
Tighten all hardware from the previous steps using the appropriate tools.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
CONGRATULATIONS!
You have completed assembly of your Strength Trainer International Bench.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
Seat Adjustments
To move the seat (21), loosen the "T"-handle (45) and pull it out as far as it will go. Slide the
seat carriage (42) to the desired position and release the "T"-handle (45) back into the bench
frame (8). Retighten the "T"-handle (45). See Figure A
To adjust the angle of the seat (21), remove the seat adjustment pin (40). Insert the pin into
the other hole on the seat frame (10) and the tube on the seat carriage (42). See Figure B.
8
21
42
45
42
21
10
40
Figure A
Figure B
Backrest Adjustment
First, move the seat pad to the desired position (see the Seat Pad Adjustment section). Next,
move the adjustment tube (9) to the desired height. Make sure the pins on the adjustment
tube are inserted into the brackets on the left and right uprights (3 & 4). Finally, rest the
backrest on the adjustment tube.
22
9
Pin
4
3
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Attachments
Curl Bar Attachment
Attach the curl bar (31) to the leg lever (18) and secure by inserting the curl bar pin (28).
Note: You will need to remove the curl bar when using the leg extension.
18
31
28
Olympic Plate Adapter
To use olympic weights, press the 48mm round inner cap (38) into the olympic adapter (47).
Secure the olympic adapter (47) to the weight tube (19) using M8X10mm set screw (60).
Make sure the set screw (60) is on the bottom of the adapter. Secure the weight plates with
included large spring clip (not shown).
18
24
12
47
19
60
38
WARNING!
Do not place more than 150 pounds on the weight tube. Secure the weights with spring clips.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Attachments
Arm Curl Post
Remove the 64mm square inner cap (69) from front leg (12). Insert the curl post (13) into the
front leg (12) and align the holes. Secure the curl post (13) with the curl post knob (56).
Note: Make sure that the knob is fully tightened.
When performing exercises that do not require the curl pad (20), remove the curl post (13)
and store it on the storage tube on the right stabilizer (2). Reinsert the 64mm (69) square
inner cap into the front leg.
2
20
13
56
69
Weight Rests and Safety Spotters
To use a barbell (not included) with the weight bench, first move the weight rests (39) and
safety spotters (27) to the correct height for the exercise to be performed. Engage the locking
bars around the left and right uprights.
Note: The weight rests (39) and safety spotters (27) can be inserted onto the other side of the
left and right uprights for squat exercises.
39
Locking
Bar
27
4
Locking
Bar
WARNING!
Do not place more than 300 pounds (including barbell) on the weight rests or safety spotters.
WARNING!
Always place both weight rests (39) and safety spotters (27) at the same height. Make sure the
locking bars are securely wrapped around the uprights before setting a barbell on them.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
ST-IB PARTS LIST REV. A
REF # PARTS #
DESCRIPTION
223-01233 LEFT STABILIZER, ST-IB
223-01220 RIGHT STABILIZER, ST-IB
223-01230 LEFT UPRIGHT, ST-IB
223-01229 RIGHT UPRIGHT, ST-IB
223-01234 CROSSBAR, ST-IB
QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
4
2
2
2
1
1
1
1
1
6
3
2
2
2
1
8
4
1
2
3
3
2
4
6
1
2
1
6
1
4
2
1
2
2
1
4
5
8
1
1
1
4
1
1
13
22
22
2
1
1
1
1
2
2
1
6
4
1
2
1
1
1
2
3
4
5
6
7
8
223-01231 LEFT REAR SUPPORT, ST-IB
223-01226 RIGHT REAR SUPPORT, ST-IB
223-01223 FRAME, ST-IB
219-00636 ADJUSTMENT TUBE, ST-IB
223-01221 SEAT FRAME, ST-IB
223-01222 FRONT STABILIZER
223-01224 FRONT LEG, ST-IB
223-01225 ARM CURL POST, ST-IB
202-00172 HEX BOLT, M10*120
219-00626 UPRIGHT PLATE, ST-IB
219-00627 UPRIGHT COVER, ST-IB
223-01227 BACKREST FRAME, ST-IB
223-01228 LEG LEVER, ST-IB
219-00628 WEIGHT TUBE, ST-IB
228-00261 CURL PAD, ST-IB
228-00262 SEAT, ST-IB
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
46
47
48
49
50
51
52
53
54
55
56
57
58
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
228-00265 BACKREST, ST-IB
228-00263 FOAM PAD, ST-IB
219-00625 PAD TUBE, ST-IB
202-00775 19MM ROUND INNER CAP, ST-IB
206-00511 SQUARE BUSHING, ST-IB
219-00631 SAFETY SPOTTER, ST-IB
219-00632 Curl Bar Pin, ST-IB
202-00776 M10 x 60MM CARROAGE BOLT, ST-IB
202-00425 BOLT, M10X65
223-01232 CURL BAR, ST-IB
202-00773 25MM x 40MM INNER CAP, ST-IB
202-00294 HEX BOLT, M10X70
202-00777 57MM SQUARE INNER CAP, ST-IB
202-00791 25MM x 50MM INNER CAP, ST-IB
202-00778 25MM Square INNER CAP, ST-IB
202-00774 50MM x 100MM INNER CAP, ST-IB
202-00779 48MM ROUND INNER CAP, ST-IB
219-00633 WEIGHT REST, ST-IB
219-00630 SEAT ADJUSTMENT PIN, ST-IB
202-00780 M6X20MM SCREW, ST-IB
228-00264 SEAT CARRIAGE, ST-IB
202-00781 M10 WASHER, ST-IB
202-00786 25MM ROUND INNER CAP, ST-IB
202-00783 POP PIN, ST-IB
202-00181 HEX BOLTS M8*65
202-00181 HEX BOLTS M8*65
219-00629 OLYMPIC ADAPTOR, ST-IB
202-00784 M6x40MM SCREW, ST-IB
202-00485 NYLON NUT M8, AOLIN
202-00785 M8 WASHER, ST-IB
210-00626 SMALL SPRING CLIP, ST-IB
210-00625 LARGE SPRING CLIP, ST-IB
202-00787 M10x145MM BOLT, ST-IB
202-00445 WASHER M6, IRONMAN
202-00788 M10 x 70MM BOLT Set, ST-IB
210-00624 KNOB, ST-IB
202-00789 M4 x 16MM SCREW, ST-IB
202-00263 NYLON LOCKNUT M10
202-00263 NYLON LOCKNUT M10
202-00790 M8 x 60MM BOLT, ST-IB
202-00782 M8 x 10MM Set SCREW, ST-IB
202-00792 17MM x 9MM Spacer, ST-IB
202-00630 ROUND OUTER CAP, 25MM
202-00794 50MM SQUARE INNER CAP, ST-IB
202-00795 M10 x 95MM BOLT, ST-IB
219-00635 BUSHING, ST-IB
219-00634 BUMPER, ST-IB
202-00793 32MM ROUND INNER CAP, ST-IB
206-00510 PAD CAP, ST-IB
202-00797 64MM Square INNER CAP, ST-IB
202-00796 50MM x 75MM INNER CAP, ST-IB
202-00290 BOLT, M8X70
215-00219 OWNER'S MANUAL, ST-IB
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View
32
9
37
32
57
16
57
58
4
37
57
63
58
30
43
7
58
57
58
58
37
15
37
58
58
2
57
14
16
58
43
58
43
44
6
29
14
14
3
57
30
29
67
5
67
43
39
58
58
58
14
15
67
58
39
37
58
27
1
37
67
29
29
27
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View
36
54
23
25
22
24
25
68
48
23
23
68
17
17
58
21
24
54
48
43
23
23
23
36
43
68
24
53
57
40
35
35
10
68
20
41
45
41
67
26
42
31
13
26
33
67
59
66
57
33
41
49
50
65
69
8
34
50
50
50
65
18
49
56
55
58
33
50
61
62
50
46
55
12
64
50
49
71
34
34
58
28
57
47
19
70
44
70
51
60
52
11
38
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Information
Residential and Personal Use Limited Warranty
PLEASE READ THESE WARRANTY TERMS AND CONDITIONS FULLY AND CAREFULLY BEFORE USING YOUR KEYS FITNESS EQUIPMENT. BY
USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING TERMS AND CONDITIONS.
Frame: Lifetime
Limited Warranty
Parts: 90 days
Missing/Cosmetic Parts: 30 Days
Replacements and Returns
If after a reasonable number of attempts, a defect has not been repaired (or
the Product is deemed non-repairable by Keys technical service and support
staff), Keys, based on a case by case review, may opt to replace the Product,
or recommend an alternate resolution, such as a warranty buy-out (Product
cost, subject to deduction of a reasonable charge for usage) or a credit. Keys,
as a manufacturer, reserves the right to replace the Product with a
Factory-Reconditioned Product that meets or exceed standards comparable
to those of the replaced Product.
This Limited Warranty applies in the United States and Canada to
Products manufactured or distributed by Keys Fitness Products, L.P.
under the Keys Fitness (“Keys”) brand name (as used herein, the
“Product” or “Products”). The warranty period to the original
purchaser is listed above, and commences on the date of original
purchase of the product, unless otherwise authorized by Keys. Keys
warrants that the Product purchased from Keys or from an
authorized Keys Fitness reseller “dealer” (for residential or personal
use only, unless otherwise authorized by Keys in writing), is free
from defects in Materials and Workmanship relevant to the
functionality of the Product at initial startup, under normal use, and
during the applicable warranty period, unless otherwise determined
by Keys.
The warranty covering the replacement Product shall expire on the
date the original warranty for the replaced Product would have expired,
unless otherwise determined by Keys.
Conditions and Restrictions
This warranty excludes expendable parts if primary cause for
warranty claim is wear. Expendable parts pertain to components on
the Product that are prone to normal wear and tear. These items
vary by Product, and can include (but not limited to) hand grips, skid
pads, pedals, pedal straps, poly-v belts, console overlays, toggle
switch/button overlays, (luster free or dull) ekg plates, decals, and
any other items that are not essential to the operation of the Product,
unless otherwise determined by Keys.
This warranty DOES NOT (A) cover shipping and handling charges,
export taxes, custom duties and taxes, or any other charges associated
with transportation of the parts or Product, beyond the initial courtesy
period of 60 days from original date of purchase of the Product; (B)
extend to Products not purchased from Keys or from an authorized
Keys reseller; (C) extend to Products purchased from online auction
sites; (D) cover any extended, additional, or third party warranties if
not offered exclusively by Keys in writing; (E) cover Products installed
at fee based facilities/commercial environments (gyms, homes used as
wellness centers, etc.); (F) cover Products installed in light institutional
environments (non fee-based facilities include for example, and not be
way of limitation, fire houses, police departments, rehab centers,
hospitals, clinics, apartment complexes, club houses, etc.); (G) cover
service calls to correct installation, perform maintenance, or instruct
owners on how to use the equipment; or (H) cover a Product on which
the serial number has been purposefully or accidentally defaced or
removed and there is no proof of purchase available (if serial number is
applicable), unless authorized by Keys in writing or otherwise stated on
this warranty.
This warranty extends only to you, the original purchaser. It is not
transferable to anyone who subsequently purchases (or receives as a
gift) the Product from you. Your sales receipt, showing the
date/place of purchase and serial number (if applicable) of the
Product, is your proof of purchase, and may be required by Keys any
time a warranty parts (or service) claim is made or if no warranty
record exists for the product.
Exclusive Remedies
During the warranty period listed above, Keys will repair a Product
by correcting any minor issues (either by phone or online support)
that might be causing the Product failure. Should a technical service
and support representative be unable to correct the issue, Keys
may replace the parts (with new parts or at the option of Keys, with
serviceable used parts, that are equivalent to new parts in
performance) that become defective, malfunction, or otherwise fail
to conform to this Limited Warranty under normal use.
This Limited Warranty becomes void for Products that have been
damaged or rendered defective as a result of (a) accident, misuse, or
abuse (including but not limited to exceeding the Keys listed, maximum
weight limit); (b) use of parts not manufactured or sold by Keys; (c)
modification of the Product; (d) normal wear and tear; (e) operation on
incorrect power supplies; (f) ***failure to perform (or performing
improper) maintenance; (g) service by anyone other than Keys, or an
authorized Keys warranty service provider; (h) floods, fires,
earthquakes, lightning strikes, power surges, and other unavoidable
acts of nature; (j) residential mis-wires; or (k) incorrect setup,
installation, or assembly. Should any Product (submitted for warranty
parts replacement) be found ineligible under the terms outlined on this
warranty, an estimate for parts purchase (if available) can be furnished
at your request.
Replacement parts shall be warranted for 30 days from the shipment
reception date or through the end of the ‘replaced’ part warranty
period, whichever is longer. Any replacement parts, required past
the warranty period listed above, shall be subject to purchase at
retail price, plus any added shipping and handling charges associated
to the delivery of the part. Note that replacement parts may be
available only through the lifetime (as defined) of the Product. In
conforming to this warranty, Keys (as the manufacturer) reserves
the right to change manufacturers or vendors of any part to cover
the existing warranty.
*Parts is herein defined exclusively, for all intents and purposes, and
pertaining to this Limited Manufacturer Warranty, as components or
Materials essential to the functionality of the Product.
Keys may also provide service (if deemed necessary and if applicable)
at no charge to you during (and not to exceed) the service warranty
period listed above, in an attempt to repair the Product. Should the
Product require service at your request or out of the limited warranty
period, Keys can furnish contact information for local (to your area)
Keys authorized service providers. Service quotes, costs, and
scheduling will be strictly dependent on service provider rates and
mutual (consumer/provider) service agreements. Keys is not
responsible for any service repair costs accrued through the use of
authorized Keys service providers at your request or out of the
limited warranty period (without written consent from Keys), beyond
the limitations outlined on this warranty.
**Lifetime of a Product, is herein defined exclusively, for all intents and
purposes, and pertaining to this Limited Manufacturer Warranty, as the time
period 7 years beyond the end of production cycle of a Product in question.
Disclaimer and Release
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN
THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE
IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY.
NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW
LIMITATIONS ON IMPLIED WARRANTIES OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS LIMITED
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE
OTHER RIGHTS THAT MAY VARY FROM STATE TO STATE. THIS IS THE ONLY
EXPRESS WARRANTY APPLICABLE TO KEYS-BRANDED PRODUCTS. KEYS
NEITHER ASSUMES NOR AUTHORIZES ANYONE TO ASSUME FOR IT ANY
OTHER EXPRESS WARRANTY.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Service
(888) 340-0482
Keys Fitness Products
4009 Distribution Drive
Suite 250
Garland, TX 75041
Download from Www.Somanuals.com. All Manuals Search And Download.
|