COMPACT Hi-Fi COMPONENT SYSTEM
M-707i
INSTRUCTION MANUAL
Declaration of Conformity with regard to the EMC Directive
2004/108/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
EU Representative's:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
© B60-5763-08/00 (E, X)
Download from Www.Somanuals.com. All Manuals Search And Download.
I
6. Power Sources – This product should be operated
only from the type of power source indicated on the
product. If you are not sure of the type of power supply
to your home, consult your product dealer or local power
company.
14.Replacement Parts – When replacement parts
are required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
7.
– Polarization – This product may
CAUTION
be equipped with a polarized alternating-current line
plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This
is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose
of the polarized plug.
15.Safety Check – Upon completion of any service
or repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
16.Wall or Ceiling Mounting – This product should
be mounted to a wall or ceiling only as recommended
by the manufacturer.
17.Heat – This product should be situated away from
heat sources such as radiators, heat registers, stoves,
or other products that produce heat. Do not place a
flaming object, such as a candle or lantern, or near the
product.
8. Power Cord Protection – Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit
from the product.
18.Power Lines – An outside antenna system should
not be located in the vicinity of overhead power lines
or other electric light or power circuits, or where it can
fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken
to keep from touching such power lines or circuits as
contact with them might be fatal.
9. Lightning – For added protection for this product
during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to
lightning and power-line surges.
19.Outdoor Antenna Grounding – If an outside
antenna or cable system is connected to the product, be
sure the antenna or cable system is grounded so as to
provide some protection against voltage surges and built-
up static charges. Article 810 of the National Electrical
Code, ANSI/NFPA 70, provides information with regard to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-
discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
10.Overloading – Do not overload wall outlets,
extension cords, or integral convenience receptacles as
this can result in a risk of fire or electric shock.
11.Object and Liquid Entry – Never push objects of
any kind into this product through openings as they
may touch dangerous voltage points or short-out parts
that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
12.Servicing – Do not attempt to service this product
yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
13.Damage Requiring Service – Unplug this product
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen
into the product,
GROUND CLAMPS
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
GROUNDING CONDUCTORS
EQUIPMENT
(NEC SECTION 810-21)
GROUND CLAMP
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by
following the operating instructions.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
e) If the product has been dropped or damaged in
any way, and
Notes:
f) When the product exhibits a distinct change in
performance – this indicates a need for service.
g) If an abnormal smell or smoke is detected.
1. Item 7 is not required except for grounded or
polarized equipment.
2. Item 19 complies with UL in the U.S.A.
English
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Using the cassette.........................................19
Playing a cassette tape..........................................................19
Recording on a cassette tape...........................................19
Contents
Caution : Read the pages marked
ensure safe operation.
carefully to
¤
Clock/timer operation..................................20
Clock setting................................................................................20
Timer setting...............................................................................20
To activate/deactivate the timer.....................................21
Sleep timer setting..................................................................21
Before applying power...................................2
Safety precautions......................................................................2
IMPORTANT SAFETY INSTRUCTIONS ............2
Before use .......................................................4
Contents ...........................................................................................4
Unpacking .......................................................................................4
Description of the button name in this manual......5
Preparing the remote control unit ...................................5
In case of difficulty........................................22
General information.....................................23
Maintenance...............................................................................23
Specifications................................................24
Main unit........................................................................................24
Speakers.........................................................................................24
iPod dock.......................................................................................24
Connections ....................................................6
About MP3 and WMA .....................................8
About USB device ...........................................9
Supported iPod...............................................9
Handling discs.................................................9
Names and functions of parts .....................10
Basic function ...............................................12
Demonstration mode............................................................12
Switching the system on.....................................................12
Switching the system to standby mode....................12
Volume control..........................................................................12
Sound control.............................................................................12
Headphones................................................................................12
Unpacking
Unpack the unit carefully and make sure that all
accessories are present.
FM indoor antenna..............................................................................(1)
AM loop antenna..................................................................................(1)
iPod dock...................................................................................................(1)
iPod dock adapter................................................................................(5)
Remote control unit
with a built-in button battery.............................................(1)
Using the CD/USB device .............................13
Preparation...................................................................................13
Playing a CD/ audio file........................................................13
Selecting a desired file by file name
If any accessories are missing, or if the unit is damaged of
falls to operate, notify your dealer immediately. If your unit
was shipped to you directly, notify your shipper immediately.
Kenwood recommends that you retain the original carton and
packing materials in case you need to move or ship the unit in
the future.
(For audio file only) .........................................................14
Programming tracks/files....................................................14
Random play...............................................................................15
Repeat play...................................................................................15
Intro scan (For CD only)........................................................15
Recording on a USB device (For CD only).................15
Program recording (For CD only) ...................................16
Changing the display of the disc/USB device
Keep this manual handy for future reference.
information..........................................................................16
Using the iPod...............................................16
Playing an iPod ..........................................................................16
Repeat play...................................................................................16
Random play...............................................................................16
Using the radio .............................................17
Tuning in radio stations........................................................17
Storing preset.............................................................................17
Tuning to a preset radio station......................................17
Using RDS (Radio Data System).......................................17
Changing the RDS display information......................18
Tuning by Program Type (PTY search).........................18
4
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the button name in this
manual
Most of the functions are designed to be able to
operate from the remote control unit. Therefore, in
this manual, the button names are described using
the names on the remote control unit first, followed
by names on the main unit put in parenthesis.
⁄
•
•
•
The supplied battery may have shorter live than ordinary
battery due to use during operation checks.
When the remote-controllable distance gets shorter than
before, replace the battery with a new one.
Placing the remote sensor in direct sunlight, or in direct
light from a high frequency fluorescent lamp may cause a
malfunction.
In such a case, change the location of the system installation
to prevent malfunction.
Example:
X-BASS [X-bass] button
Changing the battery of the remote control
unit
Use a commercially available button battery
Button on the main unit
Button on the remote control unit
(CR2025).
1
2
Insert something narrow like a paperclip into
the hole 1 and pull out the battery tray.
Preparing the remote control unit
Pull the battery sheet out from the
remote control unit to the direction of
the arrow.
Keep on slide
Operation
Pull out
When the power cord is plugged in, standby
indicator is lit. The power turns ON by pressing
button on the remote control unit pointing at the
remote sensor. When the power comes on, press the
button you want to operate.
Replace the old battery with a new one.
CR2025(+side)
Remote sensor
Approx. 6 m
30°
30°
SLEEP
USB O.T.E
TIMER
TAPE REC
RDS
DISPLA
TIMER
SET
TIME
Y
PTY
ON
/
OFF
DISPLA
Y
S
T
E
R
E
O
/
M
O
N
O
T
U
N
E
R
b
a
n
d
CD
/
USB
TAPE mode
iPod
RVS PLAY
FWD PLAY
SEARCH
/
TUNING
ALBUM
ENTER
CLEAR
P.CALL
/
VOLUME
P.MODE
ABC
JKL
DEF
MUTE
EQ
RANDOM
GHI
MNO
¤
CAUTION
REPEA
T
PQRS
TUV
WXYZ
X-BASS
INTRO
FILE SEARCH
•
Lithium battery.
REMOTE CONTROL UNIT
RC-F0713E
Danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type.
•
•
The battery pack or batteries shall not be exposed to
excessive heat such sunshine, fire or the like.
Keep battery out of reach of children and in original
package until ready to use. Dispose of used batteries
promptly. If swallowed contact physician immediately.
English
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
iPod dock
VIDEO
FM indoor antenna
AM loop antenna
Video cord
To TV with video (composite)
input terminal
iPod
Stereo
Audio In
FM ANT.
AM ANT.
75Ω
L
™
L
˜
~
AC IN
SPEAKER
IMPEDANCE
6
Ω
™
R
˜
R
Right speaker
Left speaker
To AC wall outlet
•
Insert the plug firmly all the way
into the AC wall outlet.
¤
CAUTION
Be sure to adhere to the following, or proper
ventilation will be blocked causing damage or
fire hazard.
¤
CAUTION
The power in this equipment will not be completely cut off
from the wall outlet when the standby switch is turned off.
Install the equipment so that the wall outlet is easily
accessible and, in case of emergency, immediately unplug
the power plug from the wall outlet.
Mains plug is used as the disconnect device, It shall remain
readily operable and should not be obstructed during
intended use.
•
Do not place any objects impairing heat radiation onto
the top of the unit.
•
Leave some space around the unit (from the largest
outside dimension including projection) equal to or
greater than, shown below.
Top panel : 50 cm Back panel : 10 cm
6
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the FM antenna
Connecting the iPod adapter
Compatibility of iPod adapter
1
Connect the lead to the [FM ANT. 75Ω]
terminal.
iPod description
iPod mini
4G iPod & U2 iPod
4G iPod
Capacity
4 GB & 6 GB
20 GB
Adapter number
ANT.
75
2
Find the location that gives the best
reception.
Ω
3
4
5
6
6
7
7
3
•
Secure the antenna as high up as possible.
40 GB
iPod photo & Color U2 iPod 20 GB & 30 GB
The antenna supplied with the system is a basic antenna
for indoor use. For stable signal reception, the use of an
iPod with color display
20 GB
60 GB
outdoor antenna (commercially available) is recommended.
Disconnect the indoor antenna first before connecting an
outdoor antenna.
iPod photo
40 GB & 60 GB
•
•
If your iPod is supplied with a dock adapter, use the supplied
dock adapter.
See page 9 for the supported iPod models.
Connecting the AM antenna
1
Connect the AM antenna cord to the [AM ANT.] and [H]
terminals.
1
2
Choose the iPod adapter that fits your iPod.
Insert the iPod adapter into unit.
iPod adapter
2
Setup the antenna in the position and the direction to be
able to receive AM broadcast.
7
Adapter number
iPod dock
•
The antenna supplied with the system is for indoor use. Place
it as far away as possible from the system, your TV set, the
speaker cords, AC adapter and the power cord, and point it in
the direction that provides the best reception.
3
Connect your iPod.
Connecting the speakers
1
Connect the right speaker to terminal marked“R”, with the
red wire to + and the black wire to –.
2
Connect the left speaker to terminal marked“L”, with the red
wire to + and the black wire to –.
Insert this portion.
To remove iPod adapter
•
Insert a thin object such as the tip of a flat-blade screwdriver
into the slit on the dock adapter and lift it to remove.
•
•
For optimal sound performance, it is recommended to use
the supplied speakers.
Do not connect more than one speaker to any one pair of
+/– speaker terminals.
English
7
Download from Www.Somanuals.com. All Manuals Search And Download.
About MP3 and WMA
The playable MP3/WMA file (hereafter called Audio
file) and the media format have the following
limitation. The Audio file, which is not conforming to
the specification, may not play normally.
Playable file format of USB device
•
For the formats supported by USB devices, refer to <About
USB device> (page 9).
The maximum number of characters for
display
Playable Audio file
Playable MP3 file
•
•
File/Folder name: 30/30 characters
MP3 ID3 Tag/ WMA Contents property:
32 characters
•
•
•
•
File formats: MPEG 1/2 Audio Layer 3 file
Extension: .mp3
Transfer bit rate: 8 kbps – 320 kbps
Sampling frequency: 48/ 44.1/ 32/ 24/ 22.05/ 16/ 12/
11.025/ 8 kHz
(The information which can be displayed with this unit:
title, artist name, and album name)
⁄
Playable WMA file
•
File/Folder name is the number of the characters including
•
•
•
•
•
File format: Windows Media™ Audio compliant
Extension: .wma
Transfer bit rate: 32 kbps – 320 kbps
Sampling frequency: 48/ 44.1/ 32 kHz
Files created using functions in Windows Media™ Player 9 or
later cannot be played.
the extensions.
•
This unit can display the following versions of MP3 ID3 tag:
version 1.0/ 1.1/ 2.2/ 2.3
Limitation of structure for the file and the
folder
- WMA Professional
- WMA Lossless
- WMA Voice
•
•
Maximum number of folders: 255 (including root folder)
Maximum number of files per folder: 900 (including the
number of folders)
⁄
Playing order of the audio file
•
Do not attach the extensions to files other than the Audio file.
•
Audio files are played in the order the files are written. You can
specify the order of playback by numbering files in a folder
and writing them by folder.
If the extension is attached, the file, which is not the Audio
file, will play and outputs a loud noise, causing damage to the
speaker.
Example
•
•
The files with copy protection cannot be played.
Audio files cannot be played depending on the encoding
software setting, USB device type, and/or recording
conditions.
^
¡
:
Folder
CD
(1)
: A
Audio file
¡!
2
•
•
The unit may not be compatible with upgrade of
compression format standard and additional specifications.
Audio files encoded using VBR (Variable Bit Rate) may use bit
rates that fall outside the supported range. Audio fi les with
bit rates outside the supported range cannot be played.
3
¡"
¡#
4
¡$
5
¡%
¡P
Playable storage media
•
•
CD-ROM, CD-R, CD-RW
USB device (USB version 1.1/2.0)
• Playing order
Playing order after
⁄
•
•
•
CD-RW discs which are quick formatted by the writing
play:
¡!
software cannot be used.
➡ ¡", ¡#, ¡$, ¡%...
When recording to the maximum CD-R/RW media capacity at
once, the writing software is set to“Disc at once”.
For details on the available USB devices, refer to <About USB
device> (page 9).
Playable CD-R/RW format
•
•
ISO 9660 Level 1/2
Joliet
8
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
About USB device
Handling discs
Notes on use of the USB device
Handling precautions
Hold a CD taking care not to touch the played surface. (The side
without the printed label is the playback side.)
This unit can play audio files stored in the flash
memory and digital audio player that have a USB port
(these devices are referred to as USB devices in this
document).
Discs playable on the system
This system can play back a CD (12 cm, 8 cm), CD-ROM, CD-R,
CD-RW or the audio part of a CD-EXTRA disc.
The following restrictions are placed on the types and
usage of available USB devices:
Notes on CD-ROM/CD-R/CD-RW discs
If the CD-ROM, CD-R or CD-RW disc in use has a printable label
surface, the disc may be unable to be taken out of the system
due to sticking of the label surface. To prevent malfunction of
the system, do not use such a disc.
Available USB devices
•
•
USB devices belonging to the USB mass storage class.
USB devices whose maximum current consumption is 500
mA or less.
•
Supported formats and USB device types : FAT 16/ 32
Cautions on CD discs
Always use a CD carrying the
marking.
⁄
•
A disc without this marking may be unable to be played back
correctly.
USB Mass Storage Class : USB devices that the PC can
recognize as an external storage without using any special
driver or application software.
The disc rotates at a high speed during playback. Never use a
cracked, chipped or greatly warped disc. Otherwise, damage or
malfunction of the player may result.
Also, do not use a disc with a non-circular shape as this may
result in malfunction.
•
•
Contact the sales agent as to whether your USB device
conforms to the USB mass storage class specs.
Using an unsupported USB device can result in abnormal
playback or display of the audio file.
Even if you use the USB device conforming to the above
specs, audio files cannot be played normally depending on
the type or condition of the USB device.
Supported iPod
iPod description
iPod mini
4G iPod & U2 iPod
4G iPod
iPod photo & Color U2 iPod
iPod with color display
iPod photo
iPod nano
5G iPod (with video)
U2 iPod with video
iPod classic
iPod nano (2nd generation)
iPod nano (3rd generation)
iPod touch
⁄
•
Be sure to update the software of your iPod to the latest
version. The latest iPod software updater can be downloaded
from the Apple website.
•
The iPod cannot be connected together with its accessories
such as the cover or case. Be sure to remove any accessories
before connecting the iPod.
•
•
Video output setting of iPod needs to be set on your iPod.
When the iPod is detached from the iPod dock, the TV Out
setting of the iPod may sometimes be set to On. Check this
setting if the iPod cannot display video.
English
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and functions of parts
USB connector
Remote sensor
CD tray
28
27
1
2
SLEEP
USB O.T.E.
TAPE REC
26
RDS
TIMER
SET
TIMER
TIME
15
14
1
2
DISPLAY
PTY
ON / OFF
DISPLAY
25
24
3
4
STEREO/MONO TUNER band
CD / USB
TAPE mode
FWD PLAY
iPod
5
23
13
12
RVS PLAY
6
7
22
21
SEARCH / TUNING
ENTER
CLEAR
8
3
11
VOLUME
P.CALL / ALBUM
20
9
4
5
19
18
P.MODE
ABC
DEF
MUTE
EQ
10
11
12
RANDOM
GHI
JKL
TUV
MNO
6
10
9
17
16
15
7
8
REPEAT
INTRO
PQRS
WXYZ
X-BASS
FILE SEARCH
13
14
REMOTE CONTROL UNIT
RC-F0713E
Cassette tape door
Phones jack
10
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
16
17
9
6
TIMER SET button
To set the clock.
To set the timer.
X-BASS [X-bass] button
To switch on/off bass enhancement.
EQ [EQ] button
To select the desired sound effect : POP, CLASSIC,
ROCK, JAZZ, or FLAT (off).
1
2
[
] button
To switch the system on or to standby mode.
18
19
[standby] indicator
RDS DISPLAY button
To change the display for RDS.
MUTE button
To interrupt and resume sound reproduction.
3
4
5
CLEAR button
To delete the track/file number entered during
track/file search.
PTY button
To carry out PTY search.
To delete the file name entered during file search.
STEREO/MONO button
To switch between stereo mode and mono mode (on
FM band only) for TUNER.
20
21
11
VOLUME 5 / ∞ buttons [volume knob]
To increase or decrease the volume.
ENTER button
To confirm the selection in track/file search mode for
CD and audio file.
6
8
FWD PLAY 3/8 [3/8] button
To start or interrupt playback for CD, audio file, iPod
and TAPE.
22
23
10
3
To start or interrupt recording for TAPE.
7 [7 stop] button
To stop playback for CD, audio file and TAPE.
To stop program playback and recording for CD and
audio file.
7
8
7
5
RVS PLAY 2/8 [2/8] button
To start or interrupt playback for TAPE.
To start or interrupt recording for TAPE.
To stop recording for USB and TAPE.
SEARCH/TUNING 4 / ¢ [4 / ¢
search + / –] buttons
To search forward/backward to next/previous track
for CD.
Source buttons
To select the source you want, or to turn the system on
to the selected source.
24
25
TIMER ON/OFF button
To switch the timer on/off.
To skip tracks for CD.
To search forward/backward or to skip to the next/
previous files for audio files and iPod.
To fast forward or rewind a tape.
To tune to higher/lower radio frequency or search
radio stations for TUNER.
TIME DISPLAY button
To change the time display for CD.
To change the information display for audio files.
26
13
12
TAPE REC [TAPE rec] button
To start recording from TUNER, CD, audio file or iPod to
a cassette tape.
9
4
P.CALL/ALBUM 5 / ∞ [p.call/album up /
down] buttons
To select a preset radio station for TUNER.
To select an album (folder) of audio files and iPod.
27
28
USB O.T.E. [USB O.T.E.] button
To record from CD to a USB device.
10
11
12
P.MODE button
To program tracks/files for CD and audio file.
To program preset radio stations for TUNER.
SLEEP button
To select the sleep time.
14
15
[demo] button
To activate/deactivate the demonstration in power
on mode.
RANDOM button
To playback in random order for CD, audio file and
iPod.
[0] button
REPEAT button
To repeat one track/file or all tracks/files for CD, audio
file and iPod.
To open or close the CD tray.
13
14
INTRO button
Standby mode
To play first several seconds for each track of CD.
While the standby indicator is lit, a small amount of power is
supplied to the system to back up the memory. This is called
standby mode. Under the condition, the system can be turned
ON by the remote control unit.
digit 0 – 9/ A – Z buttons
To select a track/file number for CD and audio file.
To select a preset radio station for TUNER.
To enter file names in file search mode for audio files.
15
FILE SEARCH button
To select a desired file in audio files.
English
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic function
Demonstration mode
Volume control
The system is equipped with a demonstration
function (only display). When the power cable is
plugged in and button is pressed to turn the
system on for the first time, the demonstration
automatically starts. The demonstration consists of
sequential change of display and indicators showing
the operations, but the audio itself does not change.
The demonstration function can be cancelled as
follows.
Press VOLUME 5 (turn [volume] knob to the right)
button to increase, or press VOLUME ∞ (turn
[volume] knob to the left) to decrease the volume
level.
“VOL XX”is displayed. “VOL XX”denotes the volume
level.
To switch off the volume temporarily
Press MUTE button.
Playback continues without sound, and“MUTE”is
displayed.
To deactivate the demonstration
Press [demo] button on the main unit during
demonstration.
⁄
•
To restore the volume, press MUTE button again or adjust the
volume.
To activate the demonstration
After turning the power on, press [demo] button on
the main unit.
Sound control
The sound control system feature enables you to
enjoy special sound effects; preset equalizer settings
and bass enhancement, providing the best music
reproduction.
⁄
•
The demonstration operates automatically when; a power has
failed and then recovered, or the plug of the power cable has
been pulled out while the power was on and then plugged
back in.
To switch on preset equalizer settings
Press EQ [EQ] button to select the desired sound
effect: POP, CLASSIC, ROCK, JAZZ or FLAT (off).
Switching the system on
When an effect other than FLAT is selected, the“EQ”
icon appears on the display.
Press
[
], CD/USB [CD/USB], TUNER band
[TUNER band], TAPE mode [TAPE mode], iPod [iPod]
button.
To switch on the bass enhancement
Press X-BASS [X-bass] button.
The [standby] LED will go out.
The system will switch to the last selected source or
the selected source.
The icon“X-BASS”appears on the display.
⁄
Switching the system to standby mode
•
To switch off X-BASS, press X-BASS [X-bass] button. The icon
“X-BASS”disappears.
Press
[
] button.
•
EQ and X-BASS functions are not applied to the recording
sound.
[standby] indicator is lit.
Headphones
To listen to your stereo with headphones (separately
available), use the 3.5 mm phones jack on the main
unit.
¤
•
Excessive sound pressure from earphones and headphones
can cause hearing loss.
12
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD/USB device
Preparation
device.
•
•
The icon“MP3”appears only when an MP3-file is played.
The icon“WMA”appears only when an WMA-file is played.
When playing or recording from/to the USB device, removing
it or turning the power off may corrupt the sound source and
get it unplayable.
Loading a disc
1
Press CD/USB [CD/USB] button to select CD
mode.
2
3
Press [0] button to open the CD tray.
Playing a CD/ audio file
Press FWD PLAY 6 [6] button to start playback.
Place a disc into the tray with the label facing
up.
The track/file number and elapsed playing time of
the current track/file appear on the display.
4
Press [0] button to close the CD tray.
For a CD, the total playtime and total number of
tracks will appear in the display.
For an audio file-CD, the total album number and
total file number will appear on the display.
Basic opertions
Operation type
To stop playback
To interrupt
playback
To search for a
Operation
Press 7 [7 stop] button.
Press FWD PLAY 6 [6] button.
Press again to resume playback.
Press and hold SEARCH/TUNING 4 or
Removing a disc
particular passage ¢ [4 or ¢ search +/–] button for
during playback
1
Press [0] button, grasp the disc by its edges,
and carefully pull it out.
more than 2 seconds.
Press the FWD PLAY 6 [6] button
when the desired passage is located.
To select a track/ file Press SEARCH/TUNING 4 or ¢ [4
or ¢ search +/–] button in play or
pause mode.
2
Press [0] button to close the CD tray.
Inserting a USB device
To select a album
(For audio file only) album up or down] button in play or
Press P.CALL/ALBUM 5 or ∞ [p.call/
1
2
3
Press the
mode.
[
] button to select standby
pause mode.
Insert a USB device to the USB connector on the
front panel.
⁄
•
For audio file;“DIR:xxx TRK:xxx”appears on the display. “DIR:
xxx”indicates album number and“TRK:xxx”indicates the file
number.
Press CD/USB [CD/USB] button to select USB
mode.
•
The digit buttons, 0–9 on the remote control unit can also be
used to select a track/file.
Press the CD/USB [CD/USB] button in the CD
mode.
The total album number and total file number will
appear on the display.
Press the digit buttons as shown below:
CD
Audio file
To select track/file 2 2 and ENTER
To select track/file 23 2 and 3
To select file 120
2 and ENTER
2, 3 and ENTER
1, 2 and 0
Removing the USB device
—
1
Press the
mode.
[
] button to select standby
If the ENTER button is not pressed, the search for the selected
track/file will start in 5 seconds.
2
Remove the USB device.
⁄
•
•
•
•
To ensure good system performance; wait until the unit
completely reads the disc/USB device before proceeding.
If the disc compartment is not loaded with a disc, “NO DISC”is
displayed. If the disc is unreadable, “CHECK DISC”is displayed.
If the disc is unreadable or there is no playable audio file in
the USB device, “NO DATA”is displayed.
For audio files, reading time may exceed 10 seconds due
to the large number of songs compiled into one disc/USB
English
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD/USB device
Selecting a desired file by file name
(For audio file only)
4
Repeat steps 2 to 3 to select and store other
desired tracks/files in this way.
The icon“PGM”appears on the display.
1
2
3
In stop mode, press FILE SEARCH button.
5
Press FWD PLAY 6 [6] button to play the
programmed tracks/files.
The icon“F-SEARCH”appears on the display.
Press the digit buttons A-Z to input the first
character of the file name you want to search.
⁄
•
“PROG ITEM FULL”appears on the display, if you attempt to
program more than 60 tracks/files.
Press ENTER button.
•
•
Audio files can only be programmed within the same source.
To modify a program, press the ENTER button in stop mode.
Press the ENTER button to select the desired program
number.
“_”appears and flashes on the next of the first
character.
4
5
6
7
Repeat step 2 and 3 to enter the characters
until the one before the last character.
Now enter the new track/file number with either method
below.
For the last character, press the digit buttons
A-Z to input.
– Press the P.CALL/ALBUM 5 or ∞ [p.call/album up or
down] button to select the desired track/file.
– Press the CLEAR button to clear the track/file number
programmed. Select the new track/file number using digit
buttons“0” to “9”on the remote control unit.
If you press REPEAT button during programmed playback,
the current track or all programmed tracks/files is/are played
repeatedly.
The icon“REP.”or“REP. ALL”and the icon“PGM”appear on the
display.
Only for CD: If you press the INTRO button during
programmed playback, the first 10 seconds of every track/file
in the program will be played in sequence.
The icon“INTRO”and the icon“PGM”appear on the display.
Press FILE SEARCH button.
“SEARCHING”appears on the display.
•
•
Press FWD PLAY 6 [6] button to start
playback.
⁄
•
If the unit finds an appropriate file, the route name and the
file name will be scrolled on the display. Press TIME DISPLAY
button. Then the album number and track number will be
displayed.
•
If there is no appropriate file, “NO FILE”is displayed.
To clear the program
Press 7 [7 stop] button once in stop mode, and
twice during program playback.
Programming tracks/files
Programming tracks/files of a CD/audio file is possible
when playback is stopped. Up to 60 tracks can be
stored in the memory in any order.
The icon“PGM”disappears from the display.
⁄
•
•
“P”represents PROGRAM.
The program is automatically cleared as soon as the CD tray is
1
In stop mode, press P.MODE button to enter
program setting.
opened.
•
The function of program setting cannot be used in PLAY/
PAUSE mode.
The icon“PGM”and“– – P–01”/“– – – P–01”
appears on the display.
“– –”indicates track number of the CD.
“– – –”indicates file number of the audio file.
“P–01”indicates program number.
The icon“PGM”starts flashing.
2
3
Press P.CALL/ALBUM 5 or ∞ [p.call/album up or
down] button, or digit buttons 0–9 to select the
desired track/file.
Press ENTER button to store the selected track/
file.
The track/file number returns to“– –”/“– – –” and
the next program number appears on the display.
14
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
Random play
You can play all the tracks/files in random order.
Recording on a USB device (For CD
only)
Records songs in the CD to the USB device in MP3
format.
1
2
During playing, pause or stop mode, press
RANDOM button to enable random play mode.
The icon“RDM”appears on the display.
1
2
Insert a USB device to the USB connector on the
front panel.
To exit random mode, press RANDOM button
again.
To record all the tracks:
Stop playback.
The icon“RDM”disappears from the display.
To record a single track:
Play the track to be recorded.
Repeat play
You can play the current track/file/album or the
whole disc/USB device repeatedly.
3
Press USB O.T.E. [USB O.T.E.] button to begin
recording.
The icon“SYNC USB REC”appears on the display.
Press REPEAT button in play or pause mode.
Every time the button is pressed, the repeat play
changes in the following order:
4
To end recording, press 7 [7 stop] button.
⁄
For CD :
Repeat mode
Repeat a single track
Repeat all the tracks *1
Repeat off
•
•
During recording, it is not possible to listen to another source.
The recorded music files and folders accommodating them
are numbered automatically. These number can later be
modified.
Icon
“REP.”
“REP. ALL”
—
– Numbers assigned to folders: AL_A01…AL_A99…AL_Z99
– Numbers assigned to music files: A01_001.mp3, A01_002.
mp3…/ A99_001.mp3…/ Z99_001.mp3…
– Example
For audio file :
Repeat mode
Repeat a single file
Repeat one album *2
Repeat all the files *1
Repeat off
Icon
“REP.”
“REP. ALB.”
“REP. ALL”
—
;
KWD
;AL_A01
vA01_001.mp3
CD-1
vꢀ
v.
vA01_010.mp3
;AL_A02
vA02_001.mp3
⁄
•
•
CD-2
*1 All tracks/files are repeated continuously.
*2 This function cannot be used in program mode.
vꢁ
•
•
Music is encoded according to specification below.
– Format: MP3
– Transfer bit rate: 192 kbps
– Sampling frequency: 44.1 kHz
Recordable USB device
Intro scan (For CD only)
This function let you listen to the first 10 seconds of
each track throughout the CD.
– USB standard: USB 1.1/2.0
– File system: FAT 16/32
Press INTRO button to start scanning.
The icon“INTRO”appears on the display.
To stop the intro scan
Press INTRO button again.
The unit enters normal play mode and starts
playing from where you stop the scanning.
English
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD/USB device
Using the iPod
Inserting an iPod
Program recording (For CD only)
1
Connect a iPod to the iPod dock.
Desired CD tracks can be programmed in the desired
sequence and recorded onto a USB device.
2
Press iPod [iPod] button.
1
2
3
Insert a USB device to the USB connector on the
front panel.
The icon“iPod”appears on the display.
Playing an iPod
Press FWD PLAY 6 [6] button to start playback.
Program the desired sequence of CD tracks.
See page 14 for programming procedure.
Press USB O.T.E. [USB O.T.E.] button to begin
recording.
Basic opertions
Operation type
To interrupt
playback
Operation
The icon“SYNC USB REC”appears on the display.
Press FWD PLAY 6 [6] button.
Press again to resume playback.
Press and hold SEARCH/TUNING 4 or
⁄
To search for a
•
To end recording, press 7 [7 stop] button.
particular passage ¢ [4 or ¢ search +/–] button.
during playback
To select a song
Release to resume the playback.
Press SEARCH/TUNING 4 or ¢ [4
or ¢ search +/–] button.
Changing the display of the disc/USB
device information
To select a album *1 Press P.CALL/ALBUM 5 or ∞ [p.call/
album up or down] button.
Press TIME DISPLAY button in play or pause mode.
Every time the button is pressed, the display
changes in the following order:
For CD :
⁄
•
*1 The operation varies depending on the model of iPod.
Model other than iPod touch iPod touch
Information
Icon
The operation is available when one The album is switched to the next
of the following items is selected.
Browse item
Artists, Composers
Albums, Compilations All Songs
Genres All Artists
Status display
—
album found by following the
The current track elapsed time.
The current track remaining time.
The whole disc elapsed time.
The whole disc remaining time.
The whole CD time.
—
“REMAIN”
“TOTAL”
“TOTAL REMAIN”
—
alphabetical order of track names.
Selection
All Albums
– Example Track-A1...... Album-A
Track-B1 ...... Album-B
Track-B2 ...... Album-B
Track-C1 ...... Album-C
For audio file :
Information
Status display
Album name and file name.
Tag information (Track, album title and
artist name).
Repeat play
You can play the current song or the all songs
repeatedly.
Icon
—
—
—
Press REPEAT button.
Album number and track number.
—
Every time the button is pressed, the repeat play
changes in the following order:
Repeat mode
Repeat a single song
Repeat all songs
Repeat off
Icon
—
—
—
Random play
You can play all the album in random order.
Press RANDOM button.
Each time you press the button, Random Play turns
ON or OFF.
⁄
•
The displayed icon may not match the actual operation with
certain iPod models.
16
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the radio
Tuning in radio stations
⁄
•
During program, if no button is pressed within 20 seconds,
the system will exit program mode automatically.
1
Press TUNER band [TUNER band] button to
select the desired waveband: FM or AM.
2
Press and hold SEARCH/TUNING 4 or ¢
[4 or ¢ search +/–] button to tune in to the
desired frequency.
Tuning to a preset radio station
Press P.CALL/ALBUM 5 or ∞ [p.call/album up or
down], or digit buttons 0–9 to select the desired
preset number.
⁄
The preset number and radio frequency appear on
the display.
•
To tune to a weak station, briefly press SEARCH/TUNING
4 or ¢ [4 or ¢ search +/–] button repeatedly until
the display shows the desired frequency or when the best
reception has been obtained.
⁄
•
Press the digit buttons as shown below:
STEREO/MONO
Press the STEREO/MONO button to select mono or
stereo mode.
FM
AM
1 and ENTER
2
3
To select 1
To select 2
To select 3
To select 10
1 and ENTER
2 and ENTER
3
When stereo mode is selected, the icon“STEREO”
appears on the display (if current station is FM
stereo).
1 and 0
1 and 0
Using RDS (Radio Data System)
⁄
RDS is a system that transmits useful information (in
the form of digital data) for FM broadcasts along with
the broadcast signal. Tuners and receivers designed
for RDS reception can extract the information from
the broadcast signal for use with various functions,
such as automatic display of the station name.
•
You are able to select stereo or mono mode in FM band only.
Storing preset
You can store up to 20 for FM and 10 for AM radio
stations in the memory. When a preset radio stations
selected, the preset number appears on the display.
RDS functions
PTY (Program TYpe Identification) Search:
1
2
Press TUNER band [TUNER band] button to
select the desired waveband: FM or AM.
Automatically tunes to a station that is currently broadcasting
the specified program type (genre).
Press SEARCH/TUNING 4 or ¢ [4 or ¢
search +/–] button to tune in to the desired
frequency.
PS (Program Service Name) Display:
Automatically displays the station name transmitted by the RDS
station.
Radio Text function:
3
4
Press P.MODE button so that “P – –” appears on
the display.
Displays the radio text data transmitted by some RDS stations
when you press the RDS DISPLAY button. There is“NO TEXT”
display if no text data is transmitted.
If you want to store the radio station to another
preset number, press P.CALL/ALBUM 5 or ∞
[p.call/album up or down] to select the desired
preset number.
⁄
•
Some functions and function names may differ in certain
countries and areas.
5
6
Press ENTER button again to store the radio
station.
Repeat steps 2 to 5 to store other preset radio
stations.
English
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the radio
Oldies Music
Folk Music
Documentary
“OLDIES”
“FOLK M”
“DOCUMENT”
Changing the RDS display information
While receiving a RDS station, pressing the RDS
DISPLAY button changes the contents of the display.
Every time the button is pressed, the display
changes in the following order:
Information
4
Press PTY button to start searching.
⁄
PS (Program Service name) display
PTY (Program TYpe) display
RT (Radio Text) display
•
Under certain receiving conditions, it may take more than 1
minute to complete the search.
Frequency display and preset number display
•
If the desired program type cannot be found, “PTY NO MATCH”
is displayed, then after several seconds the display returns to
the original display.
Tuning by Program Type (PTY search)
This function lets you set the tuner to automatically
search for stations which are currently broadcasting
the type of program (genre) you want to listen to.
1
2
Press TUNER band [TUNER band] button to
select FM.
Press PTY button.
If the current station is with RDS, the program type
of the station is displayed.
3
Press SEARCH/TUNING 4 or ¢ [4 or
¢ search +/–] button to select your desired
program type.
Program type table
Program Type Name
News
Display
“NEWS”
Current Affairs
Information
Sport
“AFFAIRS”
“INFO”
“SPORT”
Education
Drama
Culture
Science
Varied Speech
Pop Music
“EDUCATE”
“DRAMA”
“CULTURE”
“SCIENCE”
“VARIED”
“POP M”
Rock Music
Easy Music
Light Classical Music
Serious Classical Music
Other Music
Weather
“ROCK M”
“EASY M”
“LIGHT M”
“CLASSICS”
“OTHER M”
“WEATHER”
“FINANCE”
“CHILDREN”
“SOCIAL”
Finance
Children’s Program
Social Affairs
Religion
Phone In
Travel
“RELIGION”
“PHONE IN”
“TRAVEL”
Leisure
“LEISURE”
“JAZZ”
“COUNTRY”
“NATION M”
Jazz Music
Country Music
National Music
18
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the cassette
Recording from a CD/ audio file
Playing a cassette tape
1
2
3
Insert a disc or a USB device.
1
2
Press TAPE mode [TAPE mode] button to TAPE.
Insert a blank cassette tape into the tape deck.
Press the area marked [push open] to open the
cassette tape door.
Press the desired source button to select the
source you want to record from.
3
Insert cassette tape into the compartment with
the open edge facing down.
For CD/ audio file-CD : Press CD/USB [CD/USB]
button to select CD input.
For USB device : Press CD/USB [CD/USB] button to
select USB input.
4
5
Close the door securely.
Press TAPE mode [TAPE mode] button to select
the desired reverse mode.
4
To record all the tracks/files:
Stop playback.
icon : plays both sides and stops.
icon : plays both sides endlessly.
icon : plays only one side of the tape and
stops.
To record a single track/file:
Play the track/file to be recorded.
5
Press TAPE REC [TAPE rec] button to set the unit
into recording standby mode.
6
7
Press SEARCH/TUNING 4 or ¢ [4 or ¢
search +/–] button to move tape to the desired
starting point.
The icon“TAPE REC”appears on the display.
6
Press FWD PLAY 3/8 [3/8] or RVS PLAY 2/8
[2/8] button to begin recording.
The icon“SYNC”appears on the display.
Press FWD PLAY 3/8 [3/8] or RVS PLAY 2/8
[2/8] button to begin playing the tape.
⁄
Recording on a cassette tape
You can record from a radio, a CD, a audio file, or a
iPod.
•
To ensure good system performance, wait until the unit
completely reads the disc/USB device before recording.
To temporarily pause the recording, press FWD PLAY 3/8
[3/8] or RVS PLAY 2/8 [2/8] button. Press it again to
resume recording.
•
For the best recording, use a normal bias tape (Type
1 only).
•
•
To end recording, press 7 [7 stop] button.
During recording, it is not possible to listen to another source.
Recording from a radio
Program recording from a CD/ audio file
Desired CD tracks/ audio file can be programmed in
the desired sequence and recorded onto a tape.
1
2
3
Insert a cassette tape into the tape
compartment and close the door.
Press TUNER band [TUNER band] button to
TUNER and select a radio station.
1
2
3
Insert a disc or a USB device.
Press TAPE REC [TAPE rec] button to set the unit
into recording standby mode.
Insert a blank cassette tape into the tape deck.
Press the desired source button to select the
source you want to record from.
The icon“TAPE REC”appears on the display.
4
Press FWD PLAY 3/8 [3/8] or RVS PLAY 2/8
[2/8] button to begin recording.
For CD/ audio file-CD : Press CD/USB [CD/USB]
button to select CD input.
For USB device : Press CD/USB [CD/USB] button to
select USB input.
⁄
•
•
To end recording, press 7 [7 stop] button.
To temporarily pause the recording, press FWD PLAY 3/8
[3/8] or RVS PLAY 2/8 [2/8] button. Press it again to
resume recording.
4
Make sure that the unit is in stop mode.
continued to next page
English
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the cassette
Clock/timer operation
Clock setting
5
Program the desired sequence of CD tracks/
audio file.
1
Press and hold TIMER SET button for more than
1 second.
See page 14 for programming procedure.
6
Press TAPE REC [TAPE rec] button to set the unit
into recording standby mode.
“CLOCK SETTING”appears on the display.
2
3
4
Press ENTER button.
The icon“TAPE REC”appears on the display.
The hour indication will start flashing.
7
Press FWD PLAY 3/8 [3/8] or RVS PLAY 2/8
[2/8] button to begin recording.
The icon“SYNC”appears on the display.
Press P.CALL/ALBUM 5 or ∞ [p.call/album up or
down] button to set the hours.
Press ENTER button to enter the minute setting
mode.
⁄
•
To end recording, press 7 [7 stop] button.
The minute indication starts flashing.
5
Press P.CALL/ALBUM 5 or ∞ [p.call/album up or
Recording from a iPod
down] button to set the minutes.
1
2
3
4
5
Connect a iPod to the iPod dock.
6
Press ENTER button to set the minutes.
Insert a blank cassette tape into the tape deck.
Press iPod [iPod] button.
⁄
•
•
•
The clock setting will be erased when the power cord is
disconnected or a power failure occurred.
Play the equipment connected to this unit.
The SEARCH/TUNING 4 or ¢ [4 or ¢ search +/-]
button can be used to move across the setting items.
Pressing the TIMER SET button for more than 1 second will
display the current time for about 20 seconds.
Press TAPE REC [TAPE rec] button to set the unit
into recording standby mode.
The icon“TAPE REC.”appears on the display.
6
Press FWD PLAY 3/8 [3/8] or RVS PLAY 2/8
[2/8] button to begin recording.
Timer setting
The system can switch on to CD, USB, TUNER, iPod or
TAPE mode automatically at a preset time, serving as
an alarm to wake you up.
⁄
•
To end recording, press 7 [7 stop] button.
The timer recording of radio programs onto a cassette
tape is also possible.
Important!
Before setting the timer, ensure that the clock is
set correctly.
When setting the timer (playback or recording) for
TUNER, be sure to select the station you wish to
tune in beforehand.
1
2
Press TIMER SET button.
The hour indication starts flashing.
Set the time to start playback.
Press P.CALL/ALBUM 5 or ∞ [p.call/album up or
down] button to set timer start hours and press
ENTER button to store the setting. Repeat the
same procedure to set the minutes.
20
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
Sleep timer setting
If the sleep timer is activated, the system will switch
to standby mode after the selected time has expired.
3
4
5
Press ENTER button.
The icon“TIMER OFF”starts flashing.
Repeat the step 2 to set the time to stop the
timer (off time).
Each press of the SLEEP button decreases the timer
period by 10 minutes. The sleep timer can be set up
to 90 minutes.
Press ENTER button.
The icon“TIMER”flashes and the source display
appears.
The icon“SLEEP”appears on the display.
The display will change to sleep time display and
change as follows:
90 min = 80 min = 70 min = 60 min = 50 min
= 40 min = 30 min = 20 min = 10 min = OFF
= …
6
Press P.CALL/ALBUM 5 or ∞ [p.call/album up or
down] button to select the desired source and
press ENTER button to store the setting.
The source switches as follows :
“CD”=“USB”=“TUNER”=“iPod” =“TAPE”=“REC
While sleep mode is in active:
To deactivate the sleep timer
TU”(recording tuner on tape) = …
7
Press P.CALL/ALBUM 5 or ∞ [p.call/album up
or down] button to set volume level and press
ENTER button to store the setting.
Press SLEEP button or press
the power off.
[
] button to turn
The icon“TIMER”changes from flashing to steadily
lit.
⁄
•
The timer is now set.
If timer off and the sleep off are all activated, the system will
switch to standby mode by the earlier timer set.
8
Switch the system to standby mode.
⁄
•
When reached the preset timer, the selected source will play
or switch to standby mode after the timer has been activated.
The SEARCH/TUNING 4 or ¢ [4 or ¢ search +/-]
button can be used to move across the setting items.
•
To activate/deactivate the timer
Press TIMER ON/OFF button.
If activated, the icon“TIMER”appears on the display.
⁄
•
The timer off will not be activated if the starting and stopping
time are the same.
•
During timer setting, if no button is pressed within
20 seconds, the system will exit timer setting mode
automatically.
English
21
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of difficulty
Resetting the Microcomputer
USB operation
“NO USB” is displayed.
The microcomputer may malfunction (unit cannot be
operated, or shows an erroneous display) if the power
cord is unplugged while the power is ON, or due to
some other external factor. If this happens, execute
the following procedure to reset the microcomputer
and return the unit to its normal operating condition.
\ Insert the USB device properly.
Cannot play.
\ The USB device is removed during playing or
recording. Record songs again after formatting
the USB device.
When the power is off (standby mode), press and
hold down the [7 stop] button on the main unit
for more than 2 seconds.
Unplug the AC cord and plug it back in if
“FACTORY RESET FINISHED” is appears.
iPod operation
“NO iPod” is displayed.
\ Insert the iPod properly.
“AUTH FAIL” is displayed.
\ Disconnect the iPod and connect it again.
•
Please note that resetting the microcomputer will clear the
contents of the memory and return the unit to the state it
was in when it left the factory.
\ Check the software version of the iPod. If it is
not the latest one, update it.
Radio reception
Noise in radio.
Check that following guide for problem resolution.
General
\ Tune to a correct frequency.
\ Adjust the direction of the FM antenna.
No sound.
\ Plug in AC cord securely.
\ Set the VOLUME control to proper sound level.
\ Adjust the position and direction of the AM
antenna.
\ Increase the distance between the system and
\ Make sure the source is set to the source you
TV or VCR.
want to operate.
\ Pull out the headphones plug from the
Cassette deck operation
headphones jack.
Cannot record.
The left and right sound outputs are reverse.
\ Replace the tape or cover tabs with adhesive
tape.
\ Clean the head.
\ Check the speaker connections and location.
The system displays features automatically.
\ Switch off the demo operation.
The system does not operate by pressing any
buttons.
\ Use only NORMAL (IEC I) tape.
\ Do not use a cassette with more than 90-
minute recording time, for the tape used in
such a cassette is very thin and tends to cause
problem such as entanglement around the
pinch roller or could be easily cut off.
\ Unplug the AC cord and plug it back in.
CD player operation
“NO DISC” is displayed.
Remote control unit
\ Insert a disc correctly (label side up).
\ Clean the disc.
\ Use a new or readable disc.
Does not function properly.
\ Replace the batteries.
\ Remove the obstacles.
\ Move closer to the system when using the
remote control and make sure that you are
pointing at unit’s remote sensor.
\ Wait until the moisture condensation at the
lens has cleared.
22
M-707i
Download from Www.Somanuals.com. All Manuals Search And Download.
General information
Maintenance
Cleaning the cabinet
•
Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution containing alcohol, spirits,
ammonia or abrasive.
Cleaning discs
•
When a disc becomes dirty, clean it with a cleaning cloth,
wipe the disc from the center out. Do not wipe in circular
motion.
•
Do not use solvents such as benzene, thinner commercially
available cleaners, or antistatic spray intended for analogue
records.
Cleaning the heads and tape path
•
To ensure good recording and playback quality, clean the
heads, the capstans and pressure rollers after every 50 hours
of tape operation.
•
•
Use a cotton swab slight moistened with cleaning fluid.
You also can clean the heads by playing a cleaning tape once.
Caution on condensation
Condensation (of dew) may occur inside the unit
when there is a great difference in temperature
between this unit and the outside. This unit may
not function properly if condensation occurs. In this
case, leave the unit for a few hours and restart the
operation after the condensation has dried up.
iPod are trademarks of Apple Inc., registered in the U.S. and
other countries.
Be specially cautious against condensation in the
following circumstances:
Windows Media is a trademark of Microsoft Corporation
registered in the U.S. and other countries.
When this unit is carried from one place to another
across a large difference in temperature, when the
humidity in the room where this unit is installed
increases, etc.
Information on Disposal of Old Electrical and
Electronic Equipment and Batteries (applicable
for EU countries that have adopted separate
waste collection systems)
Warning notice
In most cases it is an infringement of copyright to
make copies of tapes or discs without the permission
of the copyright owners. Anyone wishing to copy
commercially available tapes or disc should contact
the mechanical copyright protection society limited
or the performing rights society limited.
Products and batteries with the symbol
(crossed-out wheeled bin) cannot be disposed
as household waste.
Old electrical and electronic equipment and
batteries should be recycled at a facility capable
of handling these items and their waste
byproducts.
Contact your local authority for details in
locating a recycle facility nearest to you.
Proper recycling and waste disposal will help
conserve resources whilst preventing
detrimental effects on our health and the
environment.
Notice: The sign“Pb”below the symbol for
batteries indicates that this battery
contains lead.
English
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Main unit
Speakers
Enclosure ..................................................................... Bass-reflex type
Speaker configuration
Amplifier section
Rated output power
Woofer........................................................ 100 mm, cone type
Tweeter.........................................................35 mm, cone type
Impedance .............................................................................................6 Ω
Maximum input level................................................................... 50 W
Dimensions ...................................................W : 160 mm (6-5/16”)
H : 268 mm (10-9/16”)
..............................45 W + 45 W (1 kHz, 10% T.H.D., at 6 Ω)
Tuner section
FM tuner section
Tuning frequency range
..................................................................87.5 MHz ~ 108.0 MHz
AM tuner section
D : 218 mm (8-9/16”)
Weight (net)................................................2.2 kg (4.9 lb) (1 piece)
Tuning frequency range
.......................................................................531 kHz ~ 1,602 kHz
CD player section
iPod dock
Laser.....................................................................Semiconductor laser
Over sampling............................................................8 fs (352.8 kHz)
Laser wave length......................................................760 ~ 800 nm
Laser power class.............................................................Class 1 (IEC)
D/A conversion..................................................................................1 Bit
Video output format.......................................................... NTSC/PAL
Composite video output level .............................1 Vp-p (75 Ω)
Dimensions ...................................................W : 103 mm (4-1/16”)
H : 31 mm (1-1/4”)
D : 65 mm (2-9/16”)
USB interface
Weight (net)...............................................................0.16 kg (0.35 lb)
USB standard.......................................................................USB 1.1/2.0
Maximum supply current....................................................500 mA
File system............................................................................... FAT 16/ 32
MP3 decode
........................ Compliant with MPEG-1/2 Audio Layer-3
WMA decode
........................ Compliant with Windows Media Audio 9
Recording format..................................MP3, 192 kbps/44.1 kHz
Cassette deck section
Memory back up function
Track........................................................... 4-track, 2-channel stereo
Please note that the following items will be deleted from the
unit's memory if the power cord is disconnected from the
AC outlet.
General
Power consumption..................................................................... 75 W
Dimensions ....................................................W : 160 mm (6-5/16”)
H : 269 mm (10-9/16”)
•
•
•
•
Input selector settings
Volume level
Sound control (preset equalizer, bass enhancement)
Tuner setting
D : 345 mm (13-15/16”)
Weight (net)..................................................................5.5 kg (12.1 lb)
Notes:
•
Kenwood follows a policy of continuous advancements in
development. For this reason specifications may be changed
without notice.
•
Sufficient performance may not be exhibited at extremely
cold locations (where water freezes).
For your records
Record the serial number, found on the back of the unit,
in the spaces designated on the warranty card, and in the
space provided below. Refer to the model and serial numbers
whenever you call upon your dealer for information or service
on this product.
Model
Serial Number
Download from Www.Somanuals.com. All Manuals Search And Download.
|