AUDIO VIDEO SURROUND RECEIVER
KRF-V7020
KRF-V6020
KRF-V5020
Pepration
INSTRUCTION MANUAL
KENWOOD CORPORATION
This instruction manual is for some models.
Model availability and features (functions) may differ depending on the country and sales area.
Operations
About the supplied remote control (RC-R0508) . . .
Compared to standard remote controls, the remote control supplied with this receiver has several
operation modes. These modes enable the remote control to control other audio/video components. In
order to effectively use the remote control it is important to read the operating instructions and obtain a
proper understanding of the remote control and how to switch its operation modes (etc.).
Using the remote control without completely understanding its design and how to switch the operation
modes may result in incorrect operations.
Other
RmeCntrol
B60-4155-00 02 MA (T,E2,Q) OC 9809
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
KRF-V7020/V6020/V5020 (En/T)
Contents
Caution : Read the pages marked
safe operation.
3
carefully to ensure
Getting started ................................... 2
Before applying the power .................................. 2
Safety precautions ............................................... 2
Unpacking ............................................................ 2
How to use this manual ........................................ 4
Special features ................................................... 4
Names and functions of parts ................. 5
Setting up the system ........................... 8
Connecting audio components ........................... 8
Connecting video components............................ 9
Connecting DVD 6-channel jack ......................... 9
Connecting the antennas ..................................... 9
Connecting the system control .......................... 10
Connecting the speakers ................................... 11
Preparing the remote control (RC-R0508)......... 12
Preparing the remote control (RC-R0710)......... 13
Preparing for surround sound ................ 13
Speaker settings ................................................ 13
Preparations
Peprations
Normal playback ................................ 14
Preparing for playback ...................................... 14
Listening to a source component ...................... 15
Adjusting the sound ........................................... 15
Recording ........................................ 16
Recording audio................................................. 16
Recording video ................................................. 16
Listening to radio broadcasts................. 17
Tuning (non-RDS) radio stations ....................... 17
Using RDS (Radio Data System) ....................... 17
Using the DISPLAY key...................................... 18
Presetting RDS stations
Operations
Operations
(RDS AUTO MEMORY) ...................................... 18
Presetting radio stations manually..................... 19
Receiving preset stations .................................. 19
Receiving preset stations in order (P.CALL) ..... 19
Tuning by program type (PTY search) .............. 20
Reserving the desired information..................... 20
Ambience effects ............................... 22
Surround modes................................................. 22
Surround play ..................................................... 23
DVD 6-channel playback ................................... 23
Convenient functions ......................................... 24
Other
In case of difficulty ............................. 25
Specifications ................................... 27
Other
Quick start guide ................................. 1
Getting the most from
your remote control ............................. 3
Setup code chart ................................. 7
In case of difficulty ............................. 13
Remote operation of other components .... 14
Remote
Control
(Separate
booklet)
(RC-R0508)
RmeCntrol
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
How to use this manual
Special features
KRF-V7020/V6020/V5020 (En/T)
The manual covers the KRF-V7020, KRF-V6020, and KRF-V5020.
Items such as functions, number of jacks, and remote control details
differ somewhat between these models. To confirm the functions
available on the model you have purchased, refer to the table below.
True home theater sound
This receiver incorporates a wide variety of surround modes to bring
you maximum enjoyment from your video software. Select a surround
mode according to your equipment or the software you are going to
4
play and enjoy!
™
Terminal
Preout
Remote
Control
Model name
KRF-V7020
Dolby Pro Logic & Dolby 3 Stereo
Speaker out
Front input
Equipped
This surround system reproduces theater-like surround sound from
RC-R0508 2 systems
(A, B)
CENTER,
SURROUND, (VIDEO 1)
video software marked
.
The PRO LOGIC mode uses the built-in adaptive matrix circuit to
steer the Left, Center, Right and Surround channel audio signals.
The 3 STEREO mode will redirect the Surround signal to the front left
and right speakers when only the front and center speakers are
used.
SUBWOOFER
KRF-V6020
KRF-V5020
RC-R0508 2 systems
(A, B)
CENTER,
SURROUND,
SUBWOOFER
Not equipped
Pperations
RC-R0710 1 system
SUBWOOFER Not equipped
New DSP surround modes
The DSP (Digital Signal Processor) used for this receiver incorpo-
rates a variety of high quality adjustable sound fields, like "LIVE" and
"HALL". It is compatible with almost any kind of program source.
This manual is divided in to four sections, Preparations, Operations,
Other, and Remote Control.
Preparations
DVD 6-channel input
Shows you how to connect your audio and video components to the
receiver and prepare the surround processor.
If you own a DVD player equipped with 6-channel output, this
receiver allows you to obtain the full surround sound impact of DVD
source material featuring multi-channel encoding. Since the source
signals are digital and each channel is input independently, the
resulting ambience is far superior to what can be achieved with
conventional surround sound systems.
We've tried to make setting up your system as easy as possible.
However, since this receiver works with all of your audio and video
components, connecting the system can be fairly complex.
Operations
Shows you how to operate the various functions available from the
receiver.
Universal IR (InfraRed) remote control (RC-R0508 only)
In addition to the basic receiver, the remote control supplied with this
receiver can also operate almost all of your remote controllable audio
and video components. Just follow the simple setup procedure to
register the components you have connected.
Other
Shows you additional information such as “In case of difficulty” (trouble-
shooting) and “Specifications.”
MACRO play (RC-R0508 only)
Remote Control (Separate booklet) (RC-R0508 only)
The MACRO function lets you perform a series of operations auto-
matically, like turning ON the power of the receiver and connected
components, switching the input selectors, and starting playback.
(Be sure to register your components before starting the macro set
up procedure.
Includes the “Quick Start Guide,” which shows you how to operate
other components using the remote control, as well as a detailed
explanation of all remote control operations. Once you have registered
your components with the proper setup codes, you’ll be able to operate
both this receiver and your other AV components (TV, VCR, LD player,
CD player, etc.) using the remote control supplied with this receiver.
RDS (Radio Data System) tuner
The receiver is equipped with a RDS tuner that provides several
convenient tuning functions: RDS Auto Memory, to automatically pre-
set up to 30 RDS stations broadcasting different programs; station
name display, to show you the name of the current broadcast station;
and PTY search to let you tune stations by program type.
PTY (Program TYpe) search
Lets you tune stations by specifying the type of program you want to
hear.
EON (Enhanced Other Networks) reservation
The EON function lets you monitor information on other stations so
you can receive traffic or news programs as soon as they are
broadcast, even they are broadcast on a station different from the
one you are currently listening to. When the broadcast ends, the
receiver returns to the original station. When listening to KENWOOD
source components connected with system control cords, the input
selector on the receiver automatically switches to the tuner when a
program you desire is broadcast.
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and functions of parts
KRF-V7020/V6020/V5020 (En/T)
Frequency display,
Input display,
5
PRO LOGIC
indicator
TI.VOL indicator
Preset channel display,
Surround mode display
Band indicators
S.DIRECT indicator
AUTO indicator
For KRF-V5020
SP
SP
FM
AUTO
Speaker indicator
MUTE indicator
B
TI.VOL
MUTE
A
L
C
R
MEMO. indicator
ST. indicator
MEMO.
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR ST.
kHz DOWNMIX
DSP TUNED
SW
RDS EON PTY
TP TA NEWS
LS
S
RS
*
*****;**
TUNED indicator
MONITOR indicator
DSP indicator
3 STEREO indicator
STEREO indicator
RDS indicator
Speaker selection indicators
Output channel indicators
Display
Pepration
2
8
9
3
4 5 6 7
1
AV SURROUND RECEIVER
VOLUME CONTROL
STANDBY
BAND
AUTO
MEMORY
PTY
TA/NEWS
DISPLAY
MULTI CONTROL
INPUT SELECTOR
ON
/
STANDBY
POWER
ON OFF
SPEAKERS
SOURCE
DIRECT
VIDEO 2/
MONITOR
A
LISTEN MODE
SOUND
SETUP
B
BASS BOOST
-
–
PHONES
DOWN
UP
VIDEO
1
FRONT
REAR
VIDEO
L—AUDIO—R
0
! @ # $ % ^ & *
(
)
¡
™
For KRF-V7020
SPEAKERS
MUTE
For KRF-V5020
8 MEMORY key
*
$ VIDEO 2 / MONITOR key
% SOURCE DIRECT key
^ LISTEN MODE key
8^
^
1 POWER key
Use to turn the main power ON/OFF.
2 ON/STANDBY ( ) key
$
Use to store radio stations in the preset
memory.
£
$
9 VOLUME CONTROL knob
0 PHONES jack
Use for headphone listening.
! SPEAKERS A key
%
^
Use to select the listening mode.
& SOUND key
Use to switch the power ON/STANDBY
when the POWER is turned ON.
STANDBY indicator
¢
Use to adjust the sound quality and ambi-
ence effects.
$
3 PTY key
Use to turn speaker system A on and off.
SPEAKERS key (KRF-V5020)
Use to turn the speakers on and off.
* SETUP key
Use to select the surround sound settings.
( MULTI CONTROL knob
#
Use to perform PTY search.
4 TA/NEWS key
5 DISPLAY key
$
)
*
@ SPEAKERS B key
$
Used to make a variety of settings.
Use to change the display indications when
receiving RDS broadcasts.
Use to turn speaker system B on and off.
MUTE key (KRF-V5020)
Use to temporarily mute the sound.
) INPUT SELECTOR knob
Use to select the input sources.
¡ VIDEO 1 input jacks
(For KRF-V7020)
%
^
6 BAND key
&
Use to select the broadcast band.
7 AUTO key
&
# BASS BOOST key
%
™ FRONT/REAR key
Use to select the auto tuning mode.
Use to select the maximum adjustment
setting for the low frequency range.
Use to select FRONT or REAR for the VIDEO 1
input.
About the STANDBY indicator
This unit has a STANDBY indicator. When the STANDBY indicator is lit, the unit consumes a small amount of power to preserve the memory. This is called
STANDBY mode. This mode also lets you turn the power ON using the remote control.
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and functions of parts
KRF-V7020/V6020/V5020 (En/T)
Remote control unit (RC-R0508)
6
1
POWER
MACRO
SHIFT
TV
0
2
3
AUDIO
VIDEO
!
@
Pperations
8
P. CALL
P. CALL
BAND
6
4
¢
4
7
REC
GUIDE
5
6
#
TUNING/SKIP
VOLUME
MUTE
$
%
LISTEN
MODE
SUBWOOFER
SOUND
SETUP
^
&
*
7
8
FUNCTION
SHIFT
There are some cases in which keys (or
knobs) that have the same function on
the receiver and on the remote control
have different names. In the instruc-
tions of this manual, if the names of
corresponding keys (or knobs) on the
receiver and remote control are differ-
ent, the name of the remote control key
is indicated in parentheses.
MENU
THEME
FAV
1
2
3
TV/SAT/VID
INFO
ALT AUD
4
5
6
+100
REPEAT
RANDOM
9
Page references such as “RC0” indi-
cate pages in the remote control operation
manual (Separate booklet).
7
8
9
DISPLAY
0
+10
ENT
1 POWER key
@
8 FUNCTION SHIFT key
RC$
@ AUDIO selector key
Use to turn the receiver on and off.
Use in combination with the numeric keys
to execute alternate commands.
Selects the audio inputs and sets the re-
mote control to operate the respective
KENWOOD audio component.
If you connect audio components from
KENWOOD and other makers to the MD/
TAPE or CD jacks, you can set the remote
control to operate these components by
registering the appropriate setup code at
the respective input.
Use in combination with the input selector
(AUDIO, VIDEO, or TV) keys and SHIFT
key to turn various components on and off.
9 Numeric keys
RC$
Provide functions identical to those of the
original remote control supplied with the
component you are controlling.
To access the functions printed above the
keys, press within 3 seconds of pressing
the FUNCTION SHIFT key. Function avail-
ability varies for each component.
2 MACRO key
RC5
Use in combination with the AUDIO, VIDEO,
or TV keys to execute a series of com-
mands automatically (MACRO PLAY).
3 VIDEO selector key
Selects the video inputs and sets the re-
mote control to operate the component
registered at the respective input.
# GUIDE key
RC%
0 SHIFT key
RC5
Use to activate the OSD menu functions of
registered components.
Use in combination with the AUDIO and
VIDEO keys to change the remote control
mode without changing the input selector
or in combination with the POWER key to
turn on and off components programmed
into the remote control.
4 Multi control keys
RC$
$ VOLUME key
Use to adjust the receiver volume.
% MUTE key
Use to temporarily mute the sound.
^ SOUND key
%
^
¢
Use to operate the selected component.
5 REC key
RC$
Use to operate the selected component.
6 TUNING/SKIP key
Use during the setup procedure to specify
various settings. Use to operate the tuner
or selected component.
! TV selector key
Use to adjust the sound quality and ambi-
ence effects.
Sets the remote control to operate a TV or
cable box. This key does not change the
input selector on the receiver.
& LISTEN MODE key
Use to select the listening mode.
* SETUP key
£
7 SUBWOOFER key
¢
Use in combination with the VOLUME +/–
keys to adjust the volume of the subwoofer.
#
Use to select the surround sound settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and functions of parts
KRF-V7020/V6020/V5020 (En/T)
Remote control unit (RC-R0710)
7
1
4
2
5
8
3
6
9
POWER
8
0
1
2
Pepration
7
+10
2
6
7
DISC SKIP
A/B +100
BAND
AUTO
4P.CALL ¢
1TUNING ¡
LISTEN
MODE
MULTI CONTROL
VOL.UP
S.DIRECT
MENU
3
4
9
0
TITLE
MUTE
ENTER
SOUND
SET UP
OSD
5
6
!
@
SUB TITLE
PTY
VOL.DOWN
TA/NEWS DISPLAY
MD/TAPE TUNER
CD
PHONO
DVD/
VIDEO 2/
MONITOR 6 CH INPUT
DVD CONT VIDEO 1
#
7
REMOTE CONTROL UNIT
RC-R0710
1 Numeric keys
AUTO (7)key
&
7 DVD CONT keys
If CD or MD is selected as the input source,
these keys function as numeric keys. If
tuner is selected as the input source, these
keys are used to call up station presets.
2 Component operation keys
Use these keys to operate other compo-
nents with system control connections to
the receiver.
If tuner is selected as the input source, this
key functions as the AUTO key.
Used to operate DVD player.
While holding this key depressed, press
any of the keys masked in gray in the
above illustration to operate the corre-
sponding function of a DVD player from
KENWOOD.
Keys 3, 4, 5, 9 and ! are given the
following functions during the DVD player
control operation.
If CD or MD is selected as the input source,
this key functions as the stop key.
TUNING (1 ¡) keys
If tuner is selected as the input source,
these keys function as tuning keys.
If CD or MD is selected as the input source,
these keys function as search keys.
&
2 key
If tape is selected as the input source, this
key functions as the play key for side B of
the cassette (the side facing away from
the front of the deck).
P.CALL (4 ¢) keys
(
3 :TITLE
4 :ENTER
5 :SUB TITLE
9 :MENU
If tuner is selected as the input source,
these keys function as P.CALL keys.
If CD or MD is selected as the input source,
these keys function as skip keys.
BAND (6) key
&
! :OSD
If tuner is selected as the input source, this
key functions as the band selector key.
If CD is selected as the input source, this
key functions as the play/pause key.
If MD is selected as the input source, this
key functions as the play key.
3 LISTEN MODE, TITLE key
Use to select the listening mode.
4 MUTE, ENTER key
Use to temporarily mute the sound.
5 SOUND key
Use to adjust the sound quality and ambi-
ence effects.
6 MULTI CONTROL key
£
^
¢
For details, refer to the instruction manual
of your DVD player.
8 POWER key
Use to switch the power ON/STANDBY
when the POWER is turned ON.
9 SOURCE DIRECT key
0 VOLUME CONTROL key
! SETUP key
#
^
DISC SKIP, A/B, +100 key
If CD is selected as the input source, this key
functions as the multi-CD player disc skip
key.
#
Used to make a variety of settings.
Use to select the surround sound settings.
@ RDS operation keys
If TAPE is selected as the input source,
this (A and B) of a double cassette deck.
Use to receive RDS broadcasts.
# Input selector keys
%
Use to select the receiver's input source.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
KRF-V7020/V6020/V5020 (En/T)
Make connections as shown below.
Connecting audio components
When connecting the related system components, be sure
to also refer to the instruction manuals supplied with the
components you are connecting.
8
Do not connect the power cord to a wall outlet until all
connections are completed.
Shape of AC outlets
For U.K.
Microcomputer malfunction
For other countries
If operation is not possible or an erroneous display appears, even
though all connections have been made properly, reset the micro-
computer referring to “In case of difficulty”.
Pperations
SYSTEM CONTROL
jacks
0
∞
To AC wall outlet
Caution regarding placement
To maintain proper ventilation, be sure to leave a space around the
unit (from the largest outer dimensions, including projections) equal
to, or greater than shown below:
Left and right panels: 10 cm, Rear panel: 10 cm, Top panel: 50 cm
VIDEO 2/MONITOR jacks
The receiver’s VIDEO 2/MONITOR jacks can be used in two different
ways. Make the appropriate setting for the component connected to
the jack when the receiver is turned on.
REC OUT PLAY IN REC OUT PLAY IN
L
Use as a VIDEO 2 jack
R
You can connect a video deck or the like to these jacks and perform
video playback and recording. The initial factory setting is “VIDEO
2”.
PHONO
CD
MD / TAPE
VIDEO 2 / MONITOR
Use as a MONITOR jack
You can connect a cassette deck or the like to these jacks and make
use of the deck’s monitoring function during recording. Alternately,
you can connect a graphic equalizer to these jacks to apply compen-
sation to the music signal.
To use the VIDEO 2/MONITOR jacks as MONITOR jacks, hold down
the VIDEO 2/MONITOR key of the main unit for more two seconds so
that the indication shown below appears.
OUT
IN
Cassette deck or
graphic equalizer
^
To use these jacks as MONITOR
jacks, you must change the
appropriate setting.
OUT
Cassette deck or
MD recorder
VIDEO 2/MONITOR
IN
FM AUTO SOUND DIGITAL AUTO
SP
B
A
L
R
SW
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
MUTE
7
6
4
1
¢
¡
kHz DOWNMIX
DSP TUNED
M
ONITO R
OUT
CD player
• Atthesametimethesettingisswitchedto“MONITOR,”theaudioinput
sourceswitchestotunerandthevideoinputsourceswitchestoVIDEO
1.
• To switch the setting back to “VIDEO 2,” once again hold down the
VIDEO 2/MONITOR key for two seconds or more.
• If you decide to use the VIDEO 2/MONITOR jacks as MONITOR jacks,
make sure to delete the “VIDEO 2 (VCR2)” input from the preset
OUT
remote control (RC-R0508).
RC6
Notes
Record player
1. Be sure to insert all connection cords securely. If their connections are
imperfect, the sound may not be produced or noise may interfere.
2. Be sure to remove the power cord from the AC outlet before plugging or
unplugging any connection cords. Plugging / unplugging connection
cordswithoutdisconnectingthepowercordcancausemalfunctionsand
may damage the unit.
To use the receiver for video recording, connect a video deck to
the VIDEO 2/MONITOR jacks.
3. Do not connect power cords from components whose power consump-
tion is larger than what is indicated on the AC outlet at the rear of this unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
KRF-V7020/V6020/V5020 (En/T)
Even if your DVD player does not
havethe6-channeloutputfacility,
youcanenjoythe6-channelaudio
by connecting a multi-channel
surround processor to your DVD
player.
Connecting video components
9
6CH. INPUT
VIDEO 1
SUB
WOOFER
VIDEO 2
CENTER
VIDEO 1
SUB
WOOFER
MONITOR
VIDEO 2
CENTER
MONITOR
REC OUT PLAY IN PLAY IN
Peprations
FRONT
SURROUND
VIDEO 2
DVD 6CH. INPUT
VIDEO OUT
VIDEO IN
FRONT
SURROUND
VIDEO 2
VIDEO 2 / MONITOR VIDEO 1
DVD 6CH. INPUT
VIDEO OUT
VIDEO IN
CENTER
FRONT
SUBWOOFER
VIDEO OUT
SURROUND
Monitor TV
Multi-channel surround
processor
Video Inputs
(Yellow RCA
pin cord)
DVD player
VIDEO IN
Connecting the antennas
DVD player or LD player
Video deck
OUT
OUT
OUT
IN
Antenna terminal connections
1 Push lever.
2 Insert cord.
3 Return lever.
OUT
IN
Video inputs and outputs
(Yellow RCA pin cords)
Audio inputs and outputs
(Red and white RCA pin cords)
AMloopantenna
The supplied loop antenna is for use indoors. Place it as far as possible from
thereceiver, TVset, speakercordsandpowercord, andadjustthedirection
for best reception.
Connecting DVD 6-channel jack
FMindoorantenna
The supplied indoor antenna is for temporary use only. For stable signal
reception we recommend using an outdoor antenna. Disconnect the indoor
antenna when you connect one outdoors.
FMoutdoorantenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna into the
room and connect it to the FM 75Ω terminal.
6CH. INPUT
VIDEO 1
SUB
WOOFER
VIDEO 2
CENTER
ANTENNA
AM loop
antenna
MONITOR
AM
FRONT
SURROUND
VIDEO 2
GND
DVD 6CH. INPUT
VIDEO OUT
VIDEO IN
FM
75Ω
FM indoor antenna
FM outdoor antenna
CENTER
SURROUND
FRONT
SUBWOOFER
VIDEO OUT
DVD player equipped with
six channel output jacks, etc.
Use an antenna adaptor
(Commercially available)
The sound input to DVD 6CH. INPUT is paired with the video signal
input to 6CH. INPUT.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
KRF-V7020/V6020/V5020 (En/T)
Connecting the system control
10
Connecting system control cords after connecting a KENWOOD
audio component system lets you take advantage of convenient
system control operations.
There are two KENWOOD system control modes. Make connec-
tions according to the groups of terminal symbols shown below.
Notes
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8]
equipment for system operations. If your equipment consists of this
kind of combination, please do not connect any system control
cords. Even without system control cords, normal operations can
be carried out without effecting performance.
2. Do not connect system control cords to any components other than
those specified by KENWOOD. It may cause a malfunction and
damage your equipment.
ƒ Mode : lets you combine f, ƒ, and Fterminals
Pperations
Mode : for
terminals only
This unit is compatible with both [XS8] and [SL16] modes. It comes
from the factory set to the [SL16] mode. To switch to the [XS8] mode,
follow the instructions in “SWITCHING FROM [SL16] TO [XS8]” below.
3. Be sure the system control plugs are inserted all the way in to the
system control terminals.
SYSTEM CONTROL
cord
SYSTEM CONTROL
cord
Do not connect a system control cord to a cassette deck con-
nected to the MONITOR jacks.
SYSTEM CONTROL
(ƒ)
(ƒ)
SYSTEM CONTROL OPERATIONS
SL16
(XS8)
SL16
(XS8)
SYSTEM CONTROL
Remote Control
Lets you operate this unit with the system remote supplied with the
receiver.
SYSTEM CONTROL
switch
SYSTEM CONTROL
switch
KRF-V5020
KRF-V7020, KRF-V6020
Automatic Operation (except [XR] equipment)
When you start playback from a source component, the input selector
on this unit switches to that component automatically.
EXAMPLE: [XS8] mode connections
The underlined portion represents the setting of the system control
mode.
Synchronized Recording (except [XR] equipment)
Lets you synchronize recording with the start of playback when
recording from CD, MD or analog discs.
Receiver
[SL16] [XS8]
[SL16]
MD recorder
SWITCHING FROM [SL16] TO [XS8]
You can easily change the system control mode by adjusting the
position of the SYSTEM CONTROL switch on the rear panel.
Do this operation after completing all connections.
SYSTEM
CONTROL
cord
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
[XS]
Cassette deck
CD player
Record player
For [SL16]
For [XS8]
For [SL16]
For [XS8]
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system control
mode.
SL16
(XS8)
SL16
(XS8)
KRF-V5020
KRF-V7020, KRF-V6020
• This operation will not effect items stored in the memory.
• After switching the system control mode, turn the power off and
unplug the power cord from the wall outlet, then plug it back.
[SL16] [XS8]
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
[XS]
Receiver
SYSTEM
CONTROL
cord
Cassette deck
or MD recorder
Registering setup codes for KENWOOD audio components
(RC-R0508only)
CD player
Record player
• Once you finish making the system connections, be sure to register the
appropriate setup code for each component.
RC3
• If you own remote controllable KENWOOD audio components that are
not compatible with system control (or cannot be combined with your
other system control components), registering the setup code enables
you to control those components using the remote control supplied
with this unit (without connecting system control cords). To register
setup codes for your remote controllable KENWOOD audio compo-
nents, see "Registering setup codes for other components".
RC3
• In order to take advantage of the system control operations, the
components must be connected to the correct jacks. To use a CD
player it must be connected to the CD jacks. To use a cassette deck
(or MD recorder) it must be connected to the MD/TAPE jacks. When
using more than one CD player (etc.) only the one connected to the
specified jacks may be connected for system control.
• Some CD players and cassette decks are not compatible with the
[SL16] system control mode. Be sure to use the [XS8] system
control mode when making system connections with equipment
that is not [SL16] compatible.
• Some MD players are not system control compatible. You cannot
make system control connections to this kind of equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
KRF-V7020/V6020/V5020 (En/T)
Connecting the speakers
11
1 Strip coating.
1 Strip coating.
3 Insert cord.
2 Loosen.
2 Push lever.
4 Return lever.
3 Insert.
4 Secure.
Peprations
• Never short circuit the + and – speaker cords.
• If the left and right speakers are connected inversely or the speaker
cords are connected with reversed polarity, the sound will be unnatural
with ambiguous acoustic imaging. Be sure to connect the speakers
correctly.
Front Speakers A
Right
Left
The KRF-V5020 is
equipped with one-touch
speaker terminals.
Speaker impedance
After confirming the speaker impedance indications printed on the
rear panel of the receiver, connect speakers with matching imped-
ance ratings. Using speakers with a rated impedance other than that
indicated on the rear panel of the receiver could result in malfunctions
or damage to the speakers or receiver.
They are arranged in the
same manner as the
speaker terminals of the
KRF-V7020/KRF-V6020.
Refer to the instructions
on making connections to
the KRF-V7020/KRF-
V6020 whenmakingcon-
nections to the KRF-
V5020.
Center Speaker
PRE OUT connections
This receiver has additional preout jacks. These can be used for
various purposes, but will need to be connected to an external power
amplifier as shown in the example below.
A
L
C
R
+
+
+
-
-
-
R
L
C
FRONT SPEAKERS CENTER SPEAKER
FRONT
CENTER
SPEAKERS SPEAKER
KRF-V7020, KRF-V6020
KRF-V5020
CENTER
L
Power amplifier
Surround
R
Speakers
SUB
WOOFER
SURROUND
PRE OUT
Powered
Subwoofer
CENTER
FRONT SPEAKERS
L
R
L
B
-
-
+
+
R
SUB
WOOFER
Center Speaker
SURROUND
PRE OUT
-
SURROUND SPEAKERS
-
+
+
L
Power amplifier
R
Use the FRONT
SPEAKERS B
terminals if you
want to connect a
second front
speaker system.
(KRF-V5020 is not
equipped with
SPEAKERS B
terminal.)
• Connecting a speaker cord directly to a PRE OUT jack will not
produce any sound from the speaker.
• To use the PRE OUT jacks, press the SPEAKERS A key to the on
position (the SPEAKERS key in the case of the KRF-V5020).
Powered
Left
Right
subwoofer
Surround Speakers
(Be sure to connect both
surround speakers)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
KRF-V7020/V6020/V5020 (En/T)
Preparingtheremotecontrol(RC-R0508)
12
Speaker placement
Loading the batteries
2 Insert the batteries.
1 Remove the cover.
Center speaker
Pperations
Subwoofer
3 Close the cover.
Front
speaker
Listening
position
Surround
speaker
Front speakers : Place to the front left and right of the listening
position. Front speakers are required for all surround modes.
Center speaker : Place front and center. This speaker stabilizes the
sound image and helps recreate sound motion. Be sure to connect
a center speaker when using the Dolby 3 Stereo mode.
• Insert four AAA-size (LR03) batteries as indicated by the polarity
markings.
Surround speakers : Place to the direct left and right, or slightly
behind, the listening position at even heights, approximately 1 meter
above the ears of the listeners. These speakers recreate sound
motion and atmosphere. Required for surround playback.
Subwoofer : Reproduces powerful deep bass sounds.
Operation
When the STANDBY indicator is lit, the power turns ON when you press
the POWER key on the remote control. When the power comes ON,
press the key you want to operate.
• Although the ideal surround system consists of all the speakers
listed above, if you don't have a center speaker or a subwoofer, you
can divide those signals between the available speakers in the
speaker settings to obtain the best possible surround reproduction
Operating range
from the speakers you have available.
#
(Approx.)
Remote sensor
10 m
6 m
30˚
30˚
Model: RC-R0508
Infrared ray system
• When pressing more than one remote control key successively,
press the keys securely by leaving an interval of 1 second or more
between keys.
Notes
1. The supplied batteries may have shorter lives than ordinary batteries
due to use during operation checks.
2. Replace all four batteries with new ones when you notice a shortening
of the distance from which the remote control will operate or if the
remote control blinks 5 times when you press a key. The remote control
is designed to retain set up codes in memory while you change
batteries.
3. Placing the remote sensor in direct sunlight, or in direct light from a
high frequency fluorescent lamp may cause a malfunction.
In such a case, change the location of the system installation to
prevent malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Preparing for surround sound
KRF-V7020/V6020/V5020 (En/T)
Preparingtheremotecontrol(RC-R0710)
Speakersettings
13
To enable you to obtain optimum enjoyment from the receiver’s
listening modes, make sure to complete the speaker settings as
described below.
Loading the batteries
2 Insert the batteries.
1 Remove the cover.
SETUP
MULTI CONTROL
3 Close the cover.
Peprations
VIDEO
MULTI CONTROL
TUNING/SKIP
SETUP
SETUP
• Insert two AA-size (R6) batteries as indicated by the polarity mark-
ings.
RC-R0508
RC-R0710
Turnonthereceiver.
$
1
Operation
2Selectaspeakersystem.
1 Press the SETUP key to make the subwoofer setting indica-
When the STANDBY indicator is lit, the power turns ON when you press
the POWER key on the remote control. When the power comes ON,
press the key you want to operate.
tion (SUBW) appear.
SP
A
L
R
SW
STEREO
s
UBW Y Es
Operating range
(Approx.)
Remote sensor
2 Use the MULTI CONTROL (TUNING/SKIP) to select the ap-
propriate subwoofer setting.
1 SUBW YES: A subwoofer is connected to the receiver.
2 SUBW NO: No subwoofer is connected to the receiver.
6 m
3 Press the SETUP key to accept the setting.
• The center speaker setting indication (CNTR) appears.
30˚
30˚
SP
A
L
R
SW
STEREO
C
NTR N ML
4 Use the MULTI CONTROL (TUNING/SKIP) to select the ap-
propriate center speaker setting.
Model: RC-R0710
Infrared ray system
1 CNTR NML (normal): An average size center speaker is
connected to the receiver.
2 CNTR LRG (large):
3 CNTR NO:
Alargecenterspeakerisconnected
to the receiver.
No center speaker is connected to
the receiver.
• When pressing more than one remote control key successively,
press the keys securely by leaving an interval of 1 second or more
between keys.
5 Press the SETUP key to accept the setting.
• The surround speaker setting indication (SURR) appears.
Notes
1. The supplied batteries may have shorter lives than ordinary batteries
due to use during operation checks.
2. When the remote-controllable distance gets shorter than before,
replace both batteries with new ones.
3. Placing the remote sensor in direct sunlight, or in direct light from a
high frequency fluorescent lamp may cause a malfunction.
In such a case, change the location of the system installation to
prevent malfunction.
6 Use the MULTI CONTROL (TUNING/SKIP) to select the ap-
propriate surround speaker setting.
1 SURR YES: Surround speakers are connected to the re-
ceiver.
2 SURR NO: No surround speakers are connected to the
receiver.
7 Press the SETUP key to accept the setting.
• The receiver enters the speaker volume level adjustment mode.
• In steps 3 and 4, indications appear only for the selected
channels of the speakers that require adjusting.
Continued to next page
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing for surround sound
Normal playback
KRF-V7020/V6020/V5020 (En/T)
Preparingforplayback
14
Some preparatory steps are needed before starting playback.
Adjustthevolumelevelsforthespeakers.
3
VIDEO 2/MONITOR
ON/STANDBY
Sit in your normal listening position and listen to the test tone. Adjust the
volume levels for the speakers until all speakers seem to be equally loud.
AUTO
1 Use the MULTI CONTROL (TUNING/SKIP) to adjust the volume
when the test tone is being output from the speaker channel to
be adjusted.
Pperations
The channel indication blinks while the test tone is being output.
SP
A
L
POWER
INPUT SELECTOR
SW
SPEAKERS A/B
SPEAKERS, MUTE (KRF-V5020)
L
ch 1+ dB
The test tone issues from the speakers for 2 seconds at a time
in the following sequence:
Lch =Cch =Rch = Sch =Lch
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
Turningonthereceiver
1 Turn on the power to the related components.
changed.
¢
• If the speaker setting selects are changed, the speaker level settings
are reset.
2 Turn on the power to this receiver by pressing POWER and ON/
STANDBY keys.
2 Press the SETUP key.
SelectingTAPE/MD
• The receiver enters the mode for inputting the distance to the
speakers.
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the
source name associated with the MD/TAPE jacks to “MD,” follow the
steps below:
Oeprations
4 Inputthedistancetothespeakers.
1 Use the INPUT SELECTOR knob to select “TAPE”.
1 Measure the distance from the listening position to each of the
speakers.
2 Hold down the AUTO key for more than two seconds.
• The source indication changes to “MD”.
• To return to the original indication, repeat the above procedure.
• You also will need to change the name input to the remote control
Jot down the distance to each of the speakers.
Distance to front speakers:
____ feet (meters)
____ feet (meters)
Distance to surround speakers:
(RC-0508) to “MD”.
RC3
2 Use the MULTI CONTROL (TUNING/SKIP) to select the dis-
Selectingthespeakersystem
tance to the front speakers.
The speaker indicator to be adjusted blinks.
Press the SPEAKERS A or B key to select the speaker system to be
used.
SP
A
L
R
A ON
B ON
: Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
: Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel.
1
)FT 3. )M
Indication in feet
Indication in meters
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
A+B ON : SoundfromboththespeakersconnectedtotheSPEAKERS
A and B terminals on the rear panel.
A+B OFF : No sound from the speakers. Use this setting when listening
with headphones for stereo sound in all playback modes.
3 Press the SETUP key.
4 Repeat steps 2 and 3 to input the distance for the surround
speaker.
• Activating a surround mode or selecting “DVD 6ch” as the input
source causes speaker system A to be selected automatically.
5 Setup is complete when the input indication reappears.
On the KRF-V5020, press the SPEAKERS key to switch the speak-
ers on and off.
L
R
SW
C
D
The indicator for the speakers
you want to use should be lit.
Display when all speakers have been selected.
Speaker indicator lights.
• The speakers you selected appear on the display. Confirm that all the
speakers have been correctly selected.
SP
B
SP
A
L
R
L
R
SW
SW
• If you used the remote control (RC-R0508) to perform the settings,
press the VIDEO key at this point to turn off the remote control’s own
adjustment mode. In this case, the input source is not switched.
Models other than KRF-V5020
KRF-V5020
Selecting VIDEO 2/MONITOR
Depending on the component connected to the VIDEO 2/MONITOR
jacks, select either the “VIDEO 2” setting or the “MONITOR” setting, as
appropriate.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal playback
KRF-V7020/V6020/V5020 (En/T)
Listening to a source component
Adjusting the sound
15
VOLUME CONTROL
INPUT SELECTOR
SOURCE DIRECT
BASS BOOST
VOLUME CONTROL
SOUND
MULTI CONTROL
PHONES
SPEAKERS A/B
SPEAKERS, MUTE (KRF-V5020)
VIDEO
AUDIO
VOLUME
VIDEO
VOLUME
VOLUME
MUTE
Input selector
keys
VOLUME
TUNING/SKIP
MUTE
SOUND
MULTI CONTROL
RC-R0508
RC-R0710
SOUND
RC-R0508
RC-R0710
Use the input selector (INPUT SELECTOR (AUDIO, VIDEO))
1to select the source you want to listen to.
Adjusting the tone
The input sources change as shown below:
The following adjustments are possible if the receiver is in the stereo
mode.
Selecting a source using the INPUT SELECTOR knob
1 TUNER
Operations
2 "CD" ("CD"*)
1 Press the SOUND key to select the tone mode to be adjusted.
3 "TAPE" or "MD" ("TAPE"*)
4 "PHONO"("PHONO"*)
5 "VIDEO1" ("VCR1"*)
6 "VIDEO2" ("VCR2"*)
7 "DVD 6ch"
BASS: Select this to adjust the low frequency range.
(Press the SOUND key once.)
TREB: Select this to adjust the high frequency range.
(Press the SOUND key twice.)
Selecting a source using the AUDIO key
on the remote control (RC-R0508)
AUTO
SP
A
L
R
SW
MEMO.
ST.
STEREO
TUNED
T
REB
+4
1 "CD" ("CD"*)
2 "TAPE" or "MD" ("TAPE"*)
3 TUNER
2 Use the MULTI CONTROL (TUNING/SKIP) to adjust the sound
4 "PHONO"("PHONO"*)
quality.
Selecting a source using the VIDEO key
on the remote control (RC-R0508)
• The bass and treble levels are adjustable from -10 to +10 in 2 step
increments.
1 "VIDEO1"("VCR1"*)
2 "VIDEO2"("VCR2"*)
3 "DVD 6ch"
• The adjustment item is displayed for approximately 8 seconds.
• If you used the remote control (RC-R0508) to perform the above
setting, press the VIDEO key at this point to turn off the remote
control’s own adjustment mode. In this case, the input source is not
switched.
• When selecting an input source by using the remote control (RC-
R0710), press the desired input selector key.
• “VIDEO 2” can be selected as an input source only if the VIDEO 2/
MONITOR setting is “VIDEO 2”.
8
Once-touchlowfrequencyemphasis(bassboost)
* Once setup codes are registered in the remote control (RC-R0508),
the input name display changes according to the name of the
registered component.
The following adjustments are possible if the receiver is in the stereo
mode.
Example: if you register a VCR at the VIDEO 1 jacks, "VCR" appears
Press the BASS BOOST key.
instead of "VIDEO 1".
RC2
• When using the remote control (RC-R0508) after initial setup, any
inputs that have not been registered with a setup code are deleted
• Press the key once to select the maximum (+10) low frequency
emphasis setting.
• This key does not function when the receiver is in the sound quality
or ambience effects mode.
from the cyclic list.
RC4
• The INPUT SELECTOR on the front panel of the receiver always
cycles through all inputs.
Switching back to the previous setting
2Start playback from the selected source.
Press the BASS BOOST key again.
Use the VOLUME CONTROL (VOLUME) to adjust the
volume.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Normal playback
KRF-V7020/V6020/V5020 (En/T)
Recording audio
16
VIDEO 2 / MONITOR
Muting the sound
MUTE lets you mute the sound of the speakers.
Press the MUTE key.
SP
A
L
R
SW
MUTE
C
D
Blinks
INPUT SELECTOR
• On the KRF-V5020, this selection can be made using the control on
the receiver as well.
Recording a music source
When recording a music source, switch the VIDEO2/MONITOR
To cancel
setting to “MONITOR”.
8
Press the MUTE key again so that the “MUTE” indicator goes off.
• Muting can also be cancelled by adjusting the volume.
1 Use the input selector to select the source (other than “TAPE”)
you want to record.
SOURCE DIRECT playback (analog sources only)
2 Set the cassette deck to record.
Use this function to pass the source material direct to the amplifier,
bypassing any audio processing.
3 Start playback, then start recording.
Press the SOURCE DIRECT key.
Copying tapes
AUTO SOUND
AUTO
S.DIRECT MEMO.
ST.
When copying tapes, switch the VIDEO2/MONITOR setting to
“MONITOR”.
8
TUNED
MONITOR = TAPE copying
Oeprations
1 Press the VIDEO 2/MONITOR
• Either press the LISTEN MODE, SOUND, and SETUP keys, or
switch to another input source to cancel SOURCE DIRECT play-
back.
AUTO SOUND
AUTO
MEMO.
key.
STEREO MONITOR ST.
TUNED
To cancel
2 Use the input selector to select a source other than “TAPE”.
Press again.
3 Start playback on the cassette deck connected to the VIDEO2/
MONITOR jacks and start recording on the cassette deck con-
nected to the MD/TAPE jacks.
• If SOURCE DIRECT playback was activated when using a sur-
round mode, cancelling it reactivates the previous surround mode.
TAPE = MONITOR copying
Listening with headphones
1 Use the input selector to select “TAPE”.
1 Use the SPEAKERS A or B key (or the SPEAKERS key) to turn
2 Start playback on the cassette deck connected to the MD/TAPE
jacks and start recording on the cassette deck connected to the
VIDEO2/MONITOR jacks.
off the speaker indicator.
Make sure the SPEAKERS
indicators are turned off.
Make sure the SPEAKERS
indicators are turned off.
• To copy tapes using a double cassette deck, refer to the instruc-
tion manual of the double cassette deck.
SP
A
A
SW
MONITORfunction
C
C
You can connect a cassette deck or graphic equalizer to the VIDEO2/
MONITOR jacks of the receiver. If a graphic equalizer is connected, the
VIDEO2/MONITOR key should be left in the on position. Alternately, if
a cassette deck equipped with a 3-head system is connected to the
VIDEO2/MONITOR jacks, you will be able to monitor the just-recorded
signal while making recordings on the cassette deck. By switching the
VIDEO2/MONITOR key on and off, you can compare the sound of the
source signal and the just-recorded signal. For more information, refer
to the instruction manual of the connected component.
Models other than KRF-V5020
KRF-V5020
• If you turn off all of the speakers when in the surround mode, the
mode is cancelled as well, resulting in stereo playback.
2 Connect headphones to the PHONES jack.
PHONES
To adjust the input level when the monitor function is turned on, use the
SOUND key and the MULTI CONTROL key.
¢
Recording video
3 Use the VOLUME CONTROL knob (VOLUME) to adjust the vol-
When recording video, switch the VIDEO2/MONITOR setting to
ume.
“VIDEO2”.
8
1 Use the input selector to select the video source (other than
“VIDEO2”) you want to record.
2 Set the video deck connected to VIDEO2/MONITOR to record.
3 Start playback, then start recording.
To adjust the balance
Use the test tone feature.
$ - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to radio broadcasts
KRF-V7020/V6020/V5020 (En/T)
Tuning (non-RDS) radio stations
Using RDS (Radio Data System)
17
Radio stations can be classified into RDS (Radio Data System) stations
and other stations. To listen to or store RDS stations in the preset
memory, see the section entitled, "Using RDS".
RDS is a system that transmits useful information (in the form of digital
data) for FM broadcasts along with the broadcast signal. Tuners and
receivers designed for RDS reception can extract the information from
the broadcast signal for use with various functions, such as automatic
display of the station name.
AUTO
BAND
RDS functions:
PTY (Program Type Identification) Search
)
Automatically tunes to a station that is currently broadcasting the
specified program type (genre).
EON (Enhanced Other Network) reservation
)
MULTI CONTROL
INPUT SELECTOR
Sets the tuner to automatically switch to stations broadcasting one of
two types of programs, even though you are listening to another
station. The tuner returns to the original station when the broadcast
of the selected program ends.
AUDIO
PS (Program Service Name) Display
Automatically displays the station name transmitted by the RDS
station.
AUTO
BAND
BAND
(AUTO)
MULTI CONTROL
RDS Auto Memory function
Automatically selects and stores up to 30 RDS stations in the preset
memory.
*
TUNING/SKIP
TUNER
If fewer than 30 RDS stations have been stored in the preset memory,
regular FM stations will be stored in the remaining places.
RC-R0508
RC-R0710
Radio text function
Use the input selector to select the tuner.
1
2
Displays the radio text data transmitted by some RDS stations when
you press the DISPLAY key. There is no display if no text data was
transmitted.
Operations
Use the BAND key to select the desired broadcast band.
Each press switches the band as follows:
The "RDS" indicator lights up when an RDS broadcast (signal) is
received.
"AM" or "FM" indicator
1 FM
2 AM
FM
AUTO
MEMO.
ST.
FM AUTO SOUND DIGITAL AUTO
MHz
STEREO
TI.VOL
MUTE
SP
B
A
L
R
SW
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
TUNED
78
.
5)
3Use the AUTO key to select the desired tuning method.
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
-
-
2.
9 5)
Each press switches the tuning method as follows:
1 AUTO lit (auto tuning)
Note
2 AUTO not lit (manual tuning)
Some functions and function names may differ for certain countries
and areas.
FM
AUTO
MEMO.
ST.
MHz
STEREO
TUNED
78.
5)
Before using a function utilizing the RDS, be sure to perform the RDS
Auto Memory operation by referring to the description in “Presetting
• Normally, set to "AUTO" (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
RDS stations (RDS AUTO MEMORY)”.
*
Use the MULTI CONTROL (TUNING/SKIP) to select the
station.
4
"TUNED" is displayed when a station is received
Lights when a broadcast is
being received in stereo.
FM
AUTO
MEMO.
ST.
SP
A
L
R
SW
MHz
STEREO
TUNED
-
-
9
.
8 ))
Frequency display
Auto tuning
:
The next station is tuned automatically.
Manual tuning : Turn the knob (press the key) to select the
desired station.
• You can also use the TUNING keys on the remote control (RC-
R0710) to make the selection.
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to radio broadcasts
KRF-V7020/V6020/V5020 (En/T)
Using the DISPLAY key
Presetting RDS stations (RDS AUTO MEMORY)
18
This function automatically stores up to 30 RDS stations in the preset
memory. In order to use the EON and PTY functions, the RDS stations
must be stored in the preset memory using the RDS AUTO MEMORY
function.
MEMORY
BAND
DISPLAY
INPUT SELECTOR
DISPLAY
1Use the input selector to select the tuner.
RC-R0710
Use the BAND key to set the broadcast band to “FM”.
2
Pressing the DISPLAY key changes the contents of the
display.
3Press and hold the MEMORY key for more than 2 seconds.
Each press switches the display mode as follows:
FM AUTO SOUND DIGITAL AUTO
SP
B
TI.VOL
MUTE
A
Oeprations
L
R
SW
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
RDS EON PTY
TP TA NEWS
1 PS (Program Service name) display
2 RT (Radio Text) display
3 Frequency display
kHz DOWNMIX
DSP TUNED
A
M
UTO
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
SP
B
TI.VOL
MUTE
A
L
R
SW
1 PS (Program Service name) display:
The station name is displayed automatically when an RDS broad-
cast is received,
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
EMORY
If no PS data was sent, “NO PS” is displayed.
• After a few minutes, up to 30 RDS stations are preset in order from
channel "01".
• Stations already stored in the preset memory may be replaced by
RDS stations. (i.e., If the RDS AUTO MEMORY function finds 15
RDS stations, the stations currently preset at numbers 01~15 are
replaced by the RDS stations.)
FM AUTO SOUND DIGITAL AUTO
SP
B
TI.VOL
MUTE
A
L
R
SW
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
B
BC 1 FM
2 RT (Radio Text) display:
Text data accompanying the RDS broadcast scrolls across the
display. “NO RT” or “RT----” is displayed if the current RDS station
does not provide RT data.
FM AUTO SOUND DIGITAL AUTO
SP
B
TI.VOL
MUTE
A
L
R
SW
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
A
BCDEF GH
3 Frequency display:
Displays the frequency of the current station.
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
SP
B
TI.VOL
MUTE
A
L
R
SW
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
-
-
12). 5)
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to radio broadcasts
KRF-V7020/V6020/V5020 (En/T)
Presetting radio stations manually
19
The RDS auto memory function assigns preset numbers to RDS
stations starting from preset number "1". Therefore, be sure to execute
the RDS auto memory function before using the following operations to
manually store AM stations and other FM stations, and RDS stations.
Enter the number of the preset you want to receive (up to
"30").
2
Press the numeric keys in the following order:
“Presetting RDS stations (RDS AUTO MEMORY)”.
*
For "15", press .......... 0,5
For "20", press .......... 0,0,)
MEMORY
• If you make a mistake entering a two digit number, press the +10
key several times to return to the original display and start again.
FM
AUTO
MEMO.
ST.
SP
A
L
R
SW
MHz
STEREO
TUNED
1
5
9.
8 ))
MULTI CONTROL
Tune to the station you want to store.
1
Receiving preset stations in order (P.CALL)
2Press the MEMORY key while receiving the station.
Proceed to step 3 within 5 seconds.
(If more than 5 seconds elapse, press the MEMORY key again).
AUDIO
P.CALL
P.CALL
• When storing radio stations manually, it may take a few seconds
before the "MEMORY" indicator appears in the display after pressing
the MEMORY key depending on receiving conditions.
TUNER
Blinks for 5 seconds
Lights for 5 seconds
Operations
FM
AUTO
MEMO.
ST.
SP
A
L
R
SW
MHz
STEREO
RC-R0508
RC-R0710
TUNED
0
1
9.
8 ))
1Use the remote control to select the tuner as the source.
• The remote control switches to the tuner operating mode.
Use the MULTI CONTROL to select one of the station
3presets (1 – 30).
4Press the MEMORY key to accept the setting.
Use the P.CALL key to select the desired station.
2
• Repeat steps 1, 2, 3 and 4 to store as many stations as
necessary.
• If you store a station at a previously used preset, the old station will
be replaced by the new one.
• Each time you press the key, another preset station is received in
order.
Pressing the P.CALL (%) key (¢) does the following:
01=02=03= ...... 28=29=30=01=02=03=
Pressing the P.CALL (fi) key (4) does the following:
01+02+03+ ...... 28+29+30+01+02+03+
Receiving preset stations
Holding down the key, lets you skip through the presets, receiv-
ing each for 0.5 seconds apiece.
AUDIO
1-0, +10
TUNER
1-0, +10
RC-R0508
RC-R0710
1Use the remote control to select the tuner as the source.
• The remote control switches to the tuner operating mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to radio broadcasts
KRF-V7020/V6020/V5020 (En/T)
Tuning by program type (PTY search)
20
This function lets you set the tuner to automatically search for stations
which are currently broadcasting the type of program (genre) you want
to listen to.
“NO PROG” is displayed if this operation is attempted before
performing the RDS Auto Memory operation.
Under certain receiving conditions, it may take more than 1
minute to complete the search.
Press the PTY key to start searching.
3
PTY
EXAMPLE: Searching for a Rock Music broadcast.
Display while searching
Blinks
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
SP
B
TI.VOL
MUTE
A
L
R
SW
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
R
OCK M
Program type name display
MULTI CONTROL
Display when a station is received.
Goes out
FM AUTO SOUND DIGITAL AUTO
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
SP
B
TI.VOL
MUTE
A
L
R
SW
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
B
BC 1 FM
Station name display
MULTI CONTROL
PTY
• No sound is heard while “PTY” is blinking.
Oeprations
• If the desired program type cannot be found, “NO PROG” is
displayed, then after several seconds the display returns to the
original display.
RC-R0710
To select another program type
Preparations
Repeat steps 1, 2 and 3.
• Execute the RDS auto memory procedure.
• Set the broadcast band to FM.
• Tune to an RDS station.
Reserving the desired information
Press the PTY key to activate the PTY search mode.
1
F
AM
AUTO SOUNDDIGITAL AUTO
SP
B
MUTE
TI.VOL
A
L
R
SW
PRO LOGICS.DIRECT MEMO.
STEREO MONITST.
When the receiver is tuned to a RDS EON station (a station at which the
EON indicator lights up), this function lets you set the receiver to
automatically switch stations to receive news or traffic programs as
they are broadcast. When the broadcast is over, the receiver returns to
the original station automatically.
MHz
kHz
RDS EON PTY
TP TA NEWS
DOWNMIX DSP
TUNED
N
EWs
When an RDS broadcast is received, the program type is shown on
the display. If no PTY data is available, or if the station is not an RDS
station, “NONE” is displayed.
TA/NEWS
While the “PTY” indicator is lit, use the MULTI CONTROL
to select the program type of your choice.
2
Program type table
Program Type Name
Pop Music
Display
POP M
Program Type Name
Weather
Finance
Children’s programmes
Social affairs
Religion
Display
WEATHER
FINANCE
CHILDREN
SOCIAL A
RELIGION
PHONE IN
TRAVEL
Rock Music
*M.O.R. Music
Light Classic Music
Serious Classic Music
Other Music
News
ROCK M
M.O.R. M
LIGHT M
CLASSICS
OTHER M
NEWS
VOLUME CONTROL
Phone in
Travel
Current Affairs
Information
Sport
Education
Drama
Cultures
Science
Varied Speech
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
Leisure
LEISURE
JAZZ
COUNTRY
NATION M
OLDIES
Jazz music
Country Music
National Music
Oldies Music
Folk Music
VOLUME
TA/NEWS
FOLK M
DOCUMENT
Documentary
*M.O.R. Music (Middle of the Road Music)
RC-R0710
Preparation
• Set the broadcast band to FM.
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to radio broadcasts
KRF-V7020/V6020/V5020 (En/T)
21
Complete steps 1~3 of "Presetting RDS stations (RDS
1
When waiting for information while listening to a RDS
station without the EON function
AUTO MEMORY)".
*
Skip this step if you have already completed the RDS AUTO
MEMORY procedure.
If the “EON” indicator does not light in steps 3 and 4 and the desired
kind of information has already been selected, the information from
only the station being received will be waited for.
• The EON function will not work if all 30 FM preset stations were stored
manually using the procedure shown in “Presetting radio stations
manually”. Be sure to use the RDS automatic memory function.
TP (Traffic Program) indication
Press the TA/NEWS key to select the information type
of your choice.
2
When the “TP” indicator is lit, this means that the presently-received
station or a station in the same network is transmitting traffic informa-
tion. When “TP” is displayed for the station being received, the traffic
information of this station can be received without EON reservation.
Display When "TA" is selected
FM AUTO SOUND DIGITAL AUTO
SP
B
TI.VOL
MUTE
A
L
R
SW
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
B
BC 1 FM
"TP" lights for stations where TP (Traffic Program) information
can be received.
To cancel EON reservation
Each press switches the reservation mode as follows:
Turn the “TA” and “NEWS” indicators off.
1 TA
2 NEWS
(Traffic Announcement)
(News)
3 TA, NEWS (Traffic Announcement and News)
4 off (EON off)
Setting the volume while receiving information (TI volume)
If you preset the volume level, you can listen to the information of your
choice at that volume level automatically. After the information has
been received, the volume returns to the previous level.
• If “TA” and “NEWS” can not be selected, carry out the RDS
automatic memory function again.
*
Tune to a preset RDS station.
3
1 Hold down the TA/NEWS key for more than two seconds so that
Operations
the “TI.VOL” indicator starts blinking.
Choose an RDS preset station that displays both the "RDS" and
"EON" indicators.
FM AUTO SOUND DIGITAL AUTO
SP
B
TI.VOL
MUTE
A
L
R
SW
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
Display When "TA" is selected
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
T
I
-)5 dB
FM AUTO SOUND DIGITAL AUTO
SP
B
TI.VOL
MUTE
A
L
R
SW
AM PRO LOGIC S.DIRECT MEMO.
MHz STEREO MONITOR ST.
Blinks
RDS EON PTY
TP TA NEWS
kHz DOWNMIX
DSP TUNED
B
BC 2 FM
2 Use the VOLUME CONTROL knob to select the desired volume
Be sure "EON" appears in the display
level.
• If you want to reserve TA, receive a station with which theTP indicator
lights.
• When “EON” does not light although an RDS station is received, that
station is not transmitting EON data. Please select a different station.
Proceed to next step within five seconds.
3 Press the TA/NEWS key to enter the new setting.
• The “TI.VOL” indicator stops blinking and remains lit.
Waitfortheinformationyouselectedwhilelisteningtothe
currentstation.
4
Canceling TI volume
The receiver will wait for the desired information to start as long as the
tuner is set to a preset RDS station that displays both the "EON" and
"RDS" indicators, and the power is turned ON.
Hold down the TA/NEWS key for more than two seconds so that
the “TI.VOL” indicator goes off.
When listening to the tuner:
Be sure to stay tuned to stations that display both the “EON” and
“RDS” indicators.
To listen sources other than the tuner:
1
Tune in a station which that displays both the “EON” and “RDS”
indicators, then use the INPUT SELECTOR to switch the input to
the source you desire.
2
Even when the INPUT SELECTOR is set to a source other than
tuner, it will automatically switch to tuner when the desired EON
programstartstobroadcast. Duringthisperiod, thesourceselected
in step 1 continues playing, but will not be heard.
3
When reception of the desired EON program is complete, the
INPUT SELECTOR returns to the previous input source.
• When the power is OFF, the EON function does not operate.
• If a reserved EON program starts to broadcast during analog record-
ing, the INPUT SELECTOR switches to the tuner and the station
broadcasting the EON program is recorded.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
KRF-V7020/V6020/V5020 (En/T)
This receiver is equipped with listening modes that allow
you to enjoy an enhanced sonic ambience with a variety of
video sources.
In order to obtain the optimum effect from the surround
modes, make sure to input the proper speaker settings
DSP mode
22
The DSP mode lets you add the atmosphere of a live concert or hall
to almost any type of program source. These modes are particularly
effective when used with stereo program sources, like CD, television,
and FM radio. You might enjoy trying the LIVE or HALL mode the next
time you watch a concert or sporting event!
beforehand.
#
Manufactured under license from Dolby Laboratories.
"DOLBY", the double-D symbol and "PRO LOGIC" are trademarks of
Dolby Laboratories.
Subwoofer
Surround modes
Front speaker
Surround speaker
Dolby Pro Logic
Dolby Pro Logic is a specially encoded 2 channel surround format
designed to provide theater-like surround sound from Dolby Sur-
round encoded sources (such as video and Laserdisc software
What's DSP?
marked
).
DSP stands for Digital Signal Processor.
The way a sound is heard in an actual environment depends on a
variety of different factors. One of the most important is reverberation
(the act of decaying elements of sound echoing in various places).
The DSP modes produce the feeling of presence by using the DSP
to create reverberation, without spoiling the sound quality of the
original signal.
This receiver is equipped with a Dolby Pro Logic surround decoder
to let you enjoy the wide variety of currently available Dolby Surround
home video software.
Oeprations
Center speaker
DVD 6-channel mode
Using a DVD player or the like equipped with six (5.1) output
channels and the receiver, you can enjoy multi-channel encoded
DVD source material in all its splendor. Since the source signals are
digital and each channel is input independently, the resulting sound
quality, sense of spaciousness, and dynamic range are superb.
Subwoofer
Front speaker
Surround speaker
Center speaker
Dolby 3 Stereo
Dolby 3 Stereo is available for systems that do not have surround
speakers. When in the Dolby 3 Stereo mode, the surround information
is redirected to the front left and right speakers. This mode is
designed for use with Dolby Surround program sources, but can also
improve sound field unity for programs that are not Dolby Surround
encoded. Dialog positioning and sound image definition, however,
may not be as accurate when used with programs that are not Dolby
Surround encoded.
Subwoofer
Front speaker
Surround speakers
Center speaker
Subwoofer
Front speaker
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
KRF-V7020/V6020/V5020 (En/T)
Surround Play
DVD 6-channel playback
23
DOLBY PRO LOGIC and DOLBY 3 STEREO can be used when playing
video, DVD, or LD software bearing the
modes can be used with any source.
Using a DVD player or the like equipped with six (5.1) output channels and
the receiver, you can enjoy surround sound playback.
mark. DSP
When you try to play a disc other than Dolby Digital (AC-3) such as DTS
CD, no sound is produced or, noise may be heard. To avoid this situation,
make sure that you connect the component to the receiver’s DVD 6CH.
INPUT jacks through a surround processor which can decode the
surround signal you wont to listen to.
Connecting a DVD player which can decode the surround signal itself is
also acceptable.
LISTEN MODE
INPUT SELECTOR
LISTEN MODE
LISTEN MODE
VIDEO
RC-R0508
RC-R0710
DVD/6CH INPUT
Operations
Preparations
RC-R0508
RC-R0710
• Turn ON related components.
• Complete "Preparing for surround sound".
#
• Set the INPUT SELECTOR to the component you wish to play back
with surround sound.
Preparations
• Connect your DVD player to the DVD 6ch jacks of the receiver.
• Turn on all other components that will be used.
1Start playing the video software.
• Complete “Preparing for surround sound”.
#
2Press the LISTEN MODE key to select the listening mode.
1Select “DVD 6ch” as the input source.
Listening mode settings are stored independently for each input.
• If speaker system B is on when “DVD 6ch” is selected as the input
source, it switches off and speaker system A turns on automatically
(models other than KRF-V5020).
Each press of the LISTEN MODE key switches the setting as
listed below.
Note that the only listening mode settings that can be used for
playback with the current speaker settings are available.
Start playback of the DVD software.
2
• DOLBY PRO LOGIC
• DOLBY 3 STEREO
• LIVE (DSP)
3Adjust the volume.
• HALL (DSP)
• It is not possible individually to adjust the volume level or sound quality
(SETUP,SOUND)oftheseparatechannelswhenthereceiverisinthe
DVD 6ch mode. Adjust the volume with the controls of the DVD player.
For the powered subwoofer, you can adjust the volume of the
subwoofer using the subwoofer’s own volume control.
• STEREO
Example with the DOLBY PRO LOGIC mode selected
The channels from which sound will issue are displayed.
• When in the DVD 6ch mode, you can still use the volume control,
mute, SPEAKERS (A) key, and dimmer functions.
AUTO SOUND
PRO LOGIC
AUTO
MEMO.
ST.
SP
B
A
L
C
R
SW
S
TUNED
P
RO OL GI
Adjust the volume.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
KRF-V7020/V6020/V5020 (En/T)
Convenient functions
24
DISPLAY
MULTI CONTROL
SUBWOOFERadjustment(RC-R0508only)
It is easy to adjust the volume of the subwoofer using the remote control
(RC-R0508).
1 Press the SUBWOOFER key so that “SW” is displayed.
AUTO SOUND DIGITAL AUTO
SP
B
A
L
C
R
PRO LOGIC
MEMO.
ST.
LFE SW
LS
S
RS
TUNED
s
W
)
dB
SOUND
2 Use the VOLUME key to adjust the volume.
• The adjustable range is -10 dB to +10 dB.
VOLUME
MULTI CONTROL
SOUND
Displaydimmeradjustment
TUNING/SKIP
SUBWOOFER
The dimmer function lets you select the brightness of the receiver's
display. You might find this useful if you darken your room to watch movies
or listen to music.
SOUND
Each time you hold down the DISPLAY key for more than two
seconds, the display brightness changes among the three avail-
able settings. Select the brightness level you find most pleas-
ing.
RC-R0508
RC-R0710
Adjusting the sound
You can make further adjustments to the sound while listening to
playback in the surround mode.
Oeprations
SP
SP
SP
B
B
B
A
A
A
L
L
L
C
R
SW
PRO LOGIC
PRO LOGIC
PRO LOGIC
S
1 Press the SOUND key to select the item you want to adjust.
V
V
V
IDEO1
IDEO1
IDEO1
Each press switches the selection as listed below.
Note that some items are not displayed in certain modes.
C
R
SW
S
BASS (low frequency range sound quality adjustment)
TREB (high frequency range sound quality adjustment)
Cch (center speaker level adjustment)
%
%
C
R
SW
Sch (surround speaker level adjustment)
SW (subwoofer level adjustment)
INPUT (input level adjustment)
S
• The adjustment item for input level is displayed only when the
monitor function is activated.
2 Use the MULTI CONTROL (TUNING/SKIP) to adjust the setting
as desired.
• The adjustment item is displayed for approximately 8 seconds.
• If you use the remote control (RC-R0508) to perform the above
setting, press the VIDEO key at this point to turn off the remote
control’s own adjustment mode. In this case, the input source is not
switched.
Input level adjustment (when using the monitor function)
If the input level while using the monitor function is too high, adjust the
input level as described below.
1 Turn on the monitor function.
^
2 PresstheSOUNDkeyseveraltimesuntilthe“INPUT”indication
appears.
3 Use the MULTI CONTROL (TUNING/SKIP) to adjust the input
level.
AUTO SOUND
AUTO
SP
B
A
L
R
SW
MEMO.
STEREO MONITOR ST.
TUNED
I
NPUT -6
• The adjustment mode is displayed for approximately 8 seconds.
• The input level may be adjusted to any one of two settings: 0 and -
6. (The initial setting is 0.)
4 Press the SOUND key to return to the input indication.
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of difficulty
KRF-V7020/V6020/V5020 (En/T)
Resetting the Microcomputer
25
If the microcomputer may malfunction (unit cannot be operated,
or shows an erroneous display) if the power cord is unplugged
while the power is ON, or due to some other external factor. If this
happens, execute the following procedure to reset the micro-
computer and return the unit to its normal operating condition.
With the power cord plugged in, turn the POWER key
OFF. Then, while holding down the ON/STANDBY key,
press POWER.
• Please note that resetting the microcomputer will clear the contents
of the memory and returns the unit to the state it was in when it left the
factory.
Amplifier
Cause
Symptom
Remedy
• The speaker cords are disconnected.
No sound from the speakers.
• Connect them properly referring to “Connect-
ing the speakers”
• Adjust the volume to a proper level.
• Turn OFF the MUTE.
!
• VOLUME is set to the minimum position.
• MUTE is ON.
• The SPEAKERS switches are set to OFF.
^
$
• Set the SPEAKERS switch(es) to ON.
• Speaker cords are short-circuited.
• The speaker cord is disconnected.
The standby indicator blinks and sound is
not output.
• Turn the power off, eliminate the short-circuit-
ing, then turn on the power again.
!
Soundisnotoutputfromoneofthespeakers.
• Connect it properly referring to “Connecting
the speakers”.
• The surround speaker cords and/or the center
speaker cord is disconnected.
• A surround mode has not been engaged.
• The surround and/or center volume controls
are set to the minimum level.
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very small.
• Connect it properly referring to “Connecting
the speakers”.
• Select a surround mode.
• Adjust the speaker levels using the test tone.
$
• The audio cord from the turntable is not con-
nected to the PHONO jacks.
A humming noise is generated when the
PHONO input selector is selected.
• Insert the audio cord plugs securely into the
PHONO jacks.
• The turntable is not grounded.
• Connect the grounding wire to the GND termi-
nal on the rear panel.
Tuner
Symptom
Cause
Remedy
Radio stations cannot be received.
• No antenna is connected.
• Connect an antenna.
• The broadcast band is not set properly.
• Set the broadcast band properly.
• The frequency of the desired station is not • Tune the frequency of the desired station.
tuned.
&
Interference.
• Noise due to ignition noise from an automo- • Install the outdoor antenna away from the
bile.
road.
Other
• Noise due to interference from an electric • Turn off the power to the appliance.
appliance.
• Noise due to a nearby TV set.
• Install the receiver farther away from the TV.
A station which was preset cannot be re- • The preset station belongs to a frequency that • Preset a station with a receivable frequency.
ceived by pressing the corresponding nu-
meric key.
cannot be received.
• The preset memory was cleared because the • Preset the station again.
power cord had been unplugged for a long
period of time.
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of difficulty
KRF-V7020/V6020/V5020 (En/T)
Remote control unit
26
Symptom
Cause
Remedy
• Replace with new batteries.
Remote control operation is not possible.
• Batteries are exhausted.
@#
• The remote control unit is too far away from the • Operate the remote control unit within the
main system, controlling angle is too large, or
there is an obstacle between the receiver and
the remote.
controllable range.
• The audio cords and system control cords are • Connect properly referring to “Setting up the
not connected properly. system”.
• No software is loaded in the source compo- • Place software in the source component you
nent. want to play.
8
• An attempt is made to play a tape which is • Wait until recording has completed.
being recorded in the cassette deck.
Ohter
Memory back up function
Please note that the following items will be deleted from the unit's
memory if the power cord is disconnected from the AC outlet or the
main power switch is turned off for approximately 3 days.
• Power mode.
• Input selector settings.
• Volume level.
• Broadcast band.
• Frequency setting.
• Preset stations.
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution : Read this page carefully to ensure safe
operation.
Specifications
KRF-V7020/V6020/V5020 (En/T)
VIDEO section
AUDIOsection
VIDEO inputs / outputs
Rated power output during STEREO operation
KRF-V7020
27
VIDEO (composite) ............................................ 1 Vp-p / 75 Ω
(DIN) 1 kHz, 0.7% at 4 Ω .......................................... 100 W + 100 W
KRF-V6020, KRF-V5020
(DIN) 1 kHz, 0.7% at 4 Ω ............................................... 80 W + 80 W
Effective power output during SURROUND operation
KRF-V7020
FMtunersection
Tuning frequency range ................................... 87.5 MHz ~ 108 MHz
Usable sensitivity (DIN, 75 Ω)
MONO .................... 1.2 µV / 13.2 dBf (40 kHz DEV., S/N 26 dB)
STEREO ..................45 µV / 44.2 dBf (46 kHz DEV., S/N 46 dB)
Total harmonic distortion (DIN, 1 kHz)
MONO .........................................................0.2% (65.2 dBf input)
STEREO......................................................0.8% (65.2 dBf input)
Signal to noise ratio (DIN weighted, 1 kHz)
MONO ................................65 dB (40 kHz DEV., 65.2 dBf input)
STEREO ............................60 dB (46 kHz DEV., 65.2 dBf input)
Stereo separation (DIN, 1 kHz)..................................................36 dB
Selectivity (DIN, ±300 kHz) ........................................................64 dB
Frequency response (30 Hz ~ 15kHz) .................. +0.5 dB, –3.0 dB
FRONT (1kHz, 0.7% T.H.D. at 4 Ω one channel driven)
.............................................................................. 100 W + 100 W
CENTER (1kHz, 0.7% T.H.D. at 4 Ω one channel driven)
............................................................................................. 100 W
SURROUND (1kHz, 0.7% T.H.D. at 4 Ω one channel driven)
.............................................................................. 100 W + 100 W
KRF-V6020, KRF-V5020
FRONT (1kHz, 0.7% T.H.D. at 4 Ω one channel driven)
.................................................................................. 80 W + 80 W
CENTER (1kHz, 0.7% T.H.D. at 4 Ω one channel driven)
............................................................................................... 80 W
SURROUND (1kHz, 0.7% T.H.D. at 4 Ω one channel driven)
.................................................................................. 80 W + 80 W
AMtunersection
Tuning frequency range....................................531 kHz ~ 1,602 kHz
Usable sensitivity (30% mod., S/N 20 dB)
........................................................................ 16 µV / (600 µV/m)
Signal to noise ratio (30% mod., 1 mV input) .......................... 50 dB
Total harmonic distortion ........................... 0.05% (1 kHz, 40W, 4 Ω)
Frequency response
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dB
Signal to noise ratio
PHONO (MM)......................................................... 75 dB (IHF'66)
CD .......................................................................... 93 dB (IHF'66)
Input sensitivity / impedance
PHONO (MM)......................................................... 2.5 mV / 27 kΩ
CD ......................................................................... 200 mV / 47 kΩ
DVD 6CH (SUBWOOFER) ................................... 200 mV / 10 kΩ
Output level / impedance
GENERAL
Power consumption .................................................................. 230 W
AC outlet
SWITCHED .................................................. 2 (total 150 W max.)
Dimensions....................................................................... W : 440 mm
H : 144 mm
KRF-V7020 ................................................................. D : 400 mm
KRF-V6020, KRF-V5020 ............................................ D : 390 mm
Weight (Net)
TAPE REC .......................................................... 200 mV / 2.2 kΩ
PRE OUT (CENTER, SURROUND)........................... 1 V / 2,2 kΩ
PRE OUT (SUBWOOFER) ......................................... 2 V / 2.2 kΩ
Tone control
KRF-V7020 .......................................................................... 9.2 kg
KRF-V6020 .......................................................................... 8.4 kg
KRF-V5020 .......................................................................... 8.2 kg
BASS............................................................... ±10 dB (at 100 Hz)
TREBLE .......................................................... ±10 dB (at 10 kHz)
Other
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
Download from Www.Somanuals.com. All Manuals Search And Download.
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below.
Refer to the model and serial numbers whenever you call upon your
dealer for information or service on this product.
Model __________________ Serial Number _______________________
Download from Www.Somanuals.com. All Manuals Search And Download.
|