GPS NAVIGATION SYSTEM
DNX SERIES
DNX5360 DNX5360M
MONITOR WITH DVD RECEIVER
DDX SERIES
DDX5036 DDX5036M
INSTALLATION MANUAL
© B54-4766-10/01 (MW/M2W/XW)
Download from Www.Somanuals.com. All Manuals Search And Download.
•
This unit has the cooling fan to decrease the internal
temperature. Do not mount the unit in a place where the
cooling fan of the unit are blocked. Blocking these openings
will inhibit the cooling of the internal temperature and
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
result in malfunction.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
Cooling fan
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
•
•
•
If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
•
•
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
•
•
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
•
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
Do not press hard on the panel surface when installing the
unit to the vehicle. Otherwise scars, damage, or failure may
result.
•
•
•
¤ CAUTION
Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during and
shortly after the use of the unit. Metal part such as
the heat sink and enclosure become hot.
|
English
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
If you connect the ignition wire (red) and the battery
wire (yellow) to the car chassis (ground), you may
cause a short circuit, that in turn may start a fire. Always
connect those wires to the power source running
through the fuse box.
¤
Ignition key
switch
ACC
A
B
Ignition wire (Red)
A
Car fuse box
Battery wire (Yellow)
Car fuse box
(Main fuse)
B
FM/AM
antenna input
Antenna Cord
Ground wire (Black) -
(To car chassis)
C
C
Battery
Connect to the vehicle's parking brake
detection switch harness.
⁄
Parking sensor wire (Light Green)
PRK SW
For the sake of safety, be sure to connect the parking sensor.
Reveres sensor wire (Purple/White)
Connect to vehicle's reverse lamp harness when
using the optional rear view camera.
Steering remote control wire (Light Blue/Yellow)
To steering remote
To use the steering wheel remote control feature, you need to
an exclusive remote adapter (not supplied) matches your car is
required. When this terminal is not in use, leave its cap on.
⁄
Dimmer control wire (Orange/White)
Mute control wire (Brown)
To car light control switch
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
To connect the Kenwood navigation system,
consult your navigation manual.
⁄
Depending on what antenna you are using,
Motor antenna control wire (Blue)
Power control wire (Blue/White)
connect either to the control terminal of the motor antenna, or to the
power terminal for the booster amplifier of the film-type antenna.
When using the optional power amplifier,
connect to its power control terminal.
If no connections are made, do not let the cable come out from the tab.
⁄
|
4
DNX SERIES/ DDX SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS Antenna (Accessory 2)
(see page 8)
FUSE ( 15A )
Accessory 1
REVERSE
STEERING WHEEL
REMOTE INPUT
REMOTE CONT
White/Black
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
+
+
+
+
White
Gray/Black
ILLUMI
MUTE
Gray
Green/Black
Green
Purple/Black
ANT. CONT
P CONT
Purple
|
English
5
Download from Www.Somanuals.com. All Manuals Search And Download.
System Connection
USB device
(commercially available)
USB terminal
Rear View Camera input
• Visual input (Yellow)
Audio/Visual output
• Visual output (Yellow)
• Audio left output (White)
• Audio right output (Red)
Visual input (iPod/AV input 2 switchable)
Resistance-free mini plug (3.5φ)
Audio input (iPod/AV input 2 switchable)
Resistance-free stereo type mini plug (3.5φ)
Rear Preout
• Audio left output (White)
• Audio right output (Red)
Front Preout
• Audio left output (White)
• Audio right output (Red)
Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
|
6
DNX SERIES/ DDX SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessory Connection
iPod
(commercially available)
KCA-iP301V
(Optional Accessory)
Audio Output (Black)
Visual Output (Yellow)
(DDX5036/ DDX5036M only)
USB terminal
Navigation System
(Optional Accessory)
KCA-BT200 (Optional Accessory) input
TV Tuner (Optional Accessory)
Connection cable
(Included in the
Navigation System)
T V A N T E N N A I N P U T
Navigation units that can be connected
⁄
to this unit. (As of December, 2009):
・ KNA-G630
R O U N I T
M O O T N I T
・ KNA-G630CN
For latest information, access the
Connection cable
(Included in the TV tuner)
|
English
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the GPS Antenna
(DNX SERIES only)
GPS antenna is installed inside of the car. It should
be installed as horizontally as possible to allow easy
reception of the GPS satellite signals.
To mount the GPS antenna inside your vehicle:
1. Clean your dashboard or other surface.
2. Peel the backing off of the adhesive on the bottom
of the metal plate (accessory 3).
3. Press the metal plate (accessory 3) down firmly on
your dashboard or other mounting surface. You can
bend the metal plate (accessory 3) to conform to
a curved surface, if necessary.
4. Place the GPS antenna (accessory 2) on top of the
metal plate (accessory 3).
Accessory 2
Accessory 3
¤
•
Depending on the type of car, reception of the GPS satellite
signals might not be possible with an inside installation.
The GPS antenna should be installed at a position that is
spaced at least 12 inch (30 cm) from cellular phone or other
transmitting antennas. Signals from the GPS satellite may be
interfered with by these types of communication.
Painting the GPS antenna with (metallic) paint may cause a
drop in performance.
•
•
|
8
DNX SERIES/ DDX SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Escutcheon
Installing the Escutcheon
For Toyota/Scion
1. Cut out accessory 5 as illustrated.
Cutting line
1. Attach accessory 4 to the unit.
Accessory 5
Accessory 4
2. Fold double-sided adhesive (accessory 6) along
the slit and attach it to accessory 5 cut-out
against the center rib as illustrated. Use 2 pieces of
accessory 6 for 1 accessory 5 cut-out.
For General Motors
1. Cut out accessory 5 to meet the shape of the
opening of the center console.
2. Attach accessory 5 to the unit.
3. Attach accessory 5 cut-out to the unit.
Cut out to meet the shape of
the opening in the vehicle.
Accessory 6
Accessory 5
|
English
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation for Monitor/Player Unit
Installation on Toyota, Nissan or Mitsubishi Car using Brackets
Accessory 7 (M5x6mm)
or Accessory 8 (M5x7mm)
Car Bracket
Accessory 7 (M5x6mm)
or Accessory 8 (M5x7mm)
|
10
DNX SERIES/ DDX SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
|
English
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|