ESP100 series
Download from Www.Somanuals.com. All Manuals Search And Download.
ባ
ቢ
ቤ
ብ
ቦ
ቯ
ቮ
ቭ
ቧ
ቨ
ቩ
ቪ
ቫ
ᕡ
ᕢ
ᕣ
ᕥ
ᕦ
ᕤ
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
before using your Kenwood appliance
Read these instructions carefully and retain for future reference.
Remove all packaging and any labels.
before using for the first time
1 Wash the parts see ‘cleaning’.
2 Flush the coffee maker through with cold fresh filtered water following steps ‘to
make coffee’. Make sure you fit the pod filter holder insert and one of the pod
filters but do not use any coffee pods.
●
●
safety
●
Never attempt to remove the pod filter holder whilst coffee is brewing.
to make coffee
●
Don’t get burnt by:
●
hot parts, including the steam/hot water nozzle, pod filter holder, and coffee
outlet.
steam or hot water coming out of the steam/hot water nozzle or coffee outlet.
1 Lift the tank lid and then lift out the tank and fill with cold fresh filtered water.
Never fill above the MAX level marked. Alternatively lift the lid and fill the tank
whilst in position on the coffeemaker.
●
●
●
Keep children away from the machine. And never let the cord hang down where a
We recommend using filtered water from a Kenwood water filter as it produces
child could grab it.
better coffee and reduces limescale. Never use fizzy water.
2 Re fit the tank. Make sure that it is correctly located and apply light pressure if
necessary to ensure the valve at the bottom of the tank connects with the
bottom of the machine.
3 Note it is normal for water to remain in the compartment under the tank. This
can be dried using a sponge.
●
●
Never use a damaged machine. Get it checked or repaired: see ‘service’.
Never put the machine in water or let the cord or plug get wet – you could get
an electric shock.
Unplug
●
●
before filling with water
●
before cleaning
important
●
after use
Never operate the machine without water in the tank. Top up as
soon as the level gets low.
●
●
●
●
●
Never leave the machine on unattended
Don’t let the cord touch hot parts
Only use the pod filter and the pod filter holder supplied with this machine.
Never use ground coffee or teabags in the pod filter.
If the machine runs out of water during brewing, the OK and
steam indicator lights will flash alternately and the coffee maker
will bleep. Refill the tank and the flashing and bleeping will stop.
4 Make sure that the function lever is in the ‘0’ position.
5 Plug the coffee maker into the power supply.
6 Press the power on button and its light will glow and the OK indicator light will
flash until the correct temperature is reached (see Fig. A page ii).
7 Select the pod filter required. Three filters are available each differently coloured.
The one which is coloured black ᕡ is to be used with an espresso E.S.E. pod
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Only use the appliance for its intended domestic use. Kenwood will not accept
any liability if the appliance is subject to improper use, or failure to comply with
these instructions.
●
●
(
), the grey one ᕢ is for use with a single ‘soft’ type pod to make a single cup
of café crema ( ) and the dark red one ᕣ is for use with two ‘soft’ type pods
which are stacked one on top of the other to make 2 cups of café crema
before plugging in
Make sure your electricity supply is the same as the one shown on the
underside of the machine.
(
).
8 Place the desired pod filter into the pod filter holder. Make sure that it is fitted
correctly. The tab with the text should face the front of the unit and be held
firmly in place.
Important – UK only
9 Fit the pod(s), then push the pod filter holder into the coffee maker. The holder
will be magnetically held in place during operation.
●
The wires in the cord are coloured as follows:
Green and Yellow = Earth,
Blue = Neutral,
●
Always follow the manufacturers instructions on the positioning of the pod in the
pod filter.
Brown = Live.
●
Press the espresso pods firmly into the cavity.
Never use ground coffee.
●
●
The appliance must be protected by a 13A approved (BS1362) fuse.
WARNING: THIS APPLIANCE MUST BE EARTHED.
●
important
It is important that the correct pod is used with the correct pod filter as the
coffee maker senses what drink is required and as a result doses the right
amount of water at the correct pressure to produce the perfect drink.
10 Place a cup or cups under the coffee outlet ᕤ.
hint
Note:
●
For non-rewireable plugs the fuse cover MUST be refitted when replacing the
fuse. If the fuse cover is lost then the plug must not be used until a replacement
can be obtained. The correct fuse cover is identified by colour and a
replacement may be obtained from your Kenwood Authorised Repairer (see
Service).
●
For optimum coffee we recommend priming your machine every time it is
switched on. Fit the espresso pod filter into the pod filter holder (without a pod)
and dispense one cup of water.
The coffee outlet nozzle can be raised or lowered to fit closer to the cup or mug
on the cup stand. Simply pull down or push up ᕥ.
11 When the OK indicator light stops flashing and glows continuously, turn the
●
●
If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY. An
electric shock hazard may arise if an unwanted non-rewireable plug is
inadvertently inserted into a 13A socket outlet.
This machine complies with European Economic Community Directive
89/336/EEC.
●
(
)
function lever to the upper coffee position
coffee will dispense from the coffee outlet
and a pre-determined quantity of
(see Fig. B page ii)
key
.
12 Once all the coffee has dispensed, the coffee maker will bleep. Return the
function lever to the middle ( ) position. The OK light will flash for a couple of
seconds until the pod filter holder can be removed and emptied (see Fig. C
page ii).
ቢ
ባ
ቤ
ብ
ቦ
ቧ
ቨ
ቩ
ቪ
ቫ
ቭ
ቮ
ቯ
tank lid
cup storage
pod filter (3 supplied )
pod filter holder
coffee outlet
power on button/indicator light
OK indicator light
steam button/indicator light
drip tray cover
drip tray
steam/hot water nozzle
function lever
important
Never attempt to remove the pod filter holder with force. Always wait a few
seconds after making coffee as it will be held in place until it is safe to remove.
13 If you want to make further cups of coffee wait for the flashing OK indicator light
to glow again continuously. Wait a few seconds then pull out the pod filter
holder and fit a new coffee pod or change the pod filter if an alternative type of
coffee is desired. Continue as above.
Note: when making an espresso the coffee maker will make a pumping noise
which will cease part way through the operation but will resume again before all
the drink is dispensed. This ensures that the best coffee flavour is extracted.
After each coffee is dispensed, excess water from the brewing process will be
discharged into the drip tray.
water tank
important
When selecting the power on and steam buttons always press them firmly.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
Press the Steam button for three seconds. This will activate a descaling
program and the 3 indicator lights (On/Off, OK and Steam) will flash in
succession indicating the descaling cycle is in operation. (During this time the
pump will operate 30 seconds On followed by 2 minutes Off). Allow the entire
descaling agent to flow out from the steam/hot water nozzle. The machine will
bleep when the tank is empty.
When the tank is empty return the function lever to the middle ( ) position. (The
indicator lights will continue to flash).
Rinse the tank and fill with fresh water.
Turn the function lever to the lower steam position ( ) and allow all the fresh
water to flow out from the steam/hot water nozzle. (During this cycle the pump
will operate continuously until the tank has emptied and the coffee maker will
bleep.)
to produce steam to froth milk after having brewed
coffee
1 Ensure that the pod filter holder with a pod holder is fitted to the coffee maker.
2 Press the steam button and its light will flash (see Fig. D page ii). When the
steam indicator light glows continuously the unit is ready to produce steam
(see Fig. E page ii).
3 Place an empty jug under the steam/hot water nozzle and move the function
lever to the lower steam position ( ) to remove excess water from the system.
Return the function lever to the middle ( ) position and discard the water.
4 Part fill a jug with milk – the milk may increase up to three times in volume so
select a suitably sized jug.
8
9
●
Fresh cold semi skimmed milk gives the best results.
10 Turn the function lever to the middle ( ) position
11 Hold down the steam button for 3 seconds to reset the descale cycle and the
indicator lights will stop flashing.
5 Position the jug under the steam/hot water nozzle
6 Place the nozzle into the milk and move the function lever to the lower steam
position ( ). The milk will begin to increase in volume and appear frothy ᕦ. To
obtain a creamier froth, rotate the jug with slow movements from the bottom
upwards.
7 Once the desired temperature and froth are obtained, stop the steam by
returning the lever back to the middle ( ) position.
12 The coffee maker is now ready for use.
cleaning
1 Before cleaning, unplug and let everything cool.
2 Never immerse the appliance in water
3 Don’t wash parts in the dishwasher.
●
Never allow the milk to boil as this will spoil the flavour of the coffee.
8 Pour the frothed milk into the cups containing the espresso coffee to make a
cappuccino.
tank, pod filter, pod filter holder
Wash, rinse and allow to dry
9 Switch off the steam button in order to make further cups of coffee.
Note: After having used the steam function. The OK indicator light will flash
●
1
steam/hot water nozzle
Prior to cleaning allow some hot water to flow out of the nozzle (see ‘to
produce hot water for other drinks’ ) then unplug and allow to cool before
proceeding.
Unscrew the nozzle by turning anti-clockwise, then wash thoroughly. Check
that the hole in the nozzle is not blocked. If necessary unblock with a pin.
Clean the steam/hot water delivery tube. Make sure the end is not blocked .
Screw the nozzle back onto the delivery tube.
quickly (once per ⁄4 second) for a short period to indicate the high temperature
●
(see Fig. F page ii) during which period of time the machine is not ready for
brewing coffee. Wait until the OK indicator light glows continuously (see Fig. G
page ii) otherwise the temperature will be too high and will burn the coffee.
hint
●
●
After frothing milk, dispense hot water from the steam/hot water nozzle (see
●
below) which will help clean the nozzle and help the boiler to cool down more
quickly.
●
drip tray/drip tray cover
●
to produce hot water for other drinks, eg tea, fruit
drinks
Empty the drip tray regularly.
1 Wash then dry thoroughly.
1 Ensure that the pod filter holder with a pod holder is fitted to the coffee maker.
2 Press the power on button and its light will glow and the OK indicator light will
flash.
3 When the OK indicator light stops flashing and glows continuously, place a cup
under the steam/hot water nozzle and move the function lever to the lower
steam position
service and customer care
●
If the cord is damaged it must, for safety reasons, be replaced by Kenwood or
an authorised Kenwood repairer.
UK
If you need help with:
●
using your machine or
(
). Hot water will dispense from the nozzle.
●
servicing, spare parts or repairs (in or out of guarantee)
4 Switch off and unplug after use.
●
టcall Kenwood customer care on 023 9239 2333. Have your model
Never use teabags in the pod filter.
number ready – it’s on the underside of the coffee maker.
●
spares and attachments
setting the dispensing volume
టcall 0870 2413653.
●
The coffee maker has been programmed to dispense a pre selected quantity of
liquid which is 40ml for Espresso, 125ml for a single café crema and 250ml for
a double café crema. These volumes can only be changed by carrying out the
following procedure ensuring that the appropriate coffee pod and pod filter are
fitted.
other countries
Contact the shop where you bought your machine.
guarantee (uk only)
If your coffee maker goes wrong within one year from the date you bought it, we
will repair it (or replace it if necessary) free of charge provided:
you have not misused, neglected or damaged it;
it has not been modified (unless by Kenwood);
it is not second-hand;
it has not been used commercially;
you have not fitted a plug incorrectly; and
you supply your receipt to show when you bought it.
1 Place the required cups(s) under the coffee nozzle.
●
2 Press and hold the Steam button for 5 seconds during brewing and the OK and
steam indicator lights will flash simultaneously. When the coffee volume in the cup
reaches the required level, release the button and the water volume will be stored in
the memory. This can be re-programmed at any time following the above
procedure.
●
●
●
●
●
descaling
This guarantee does not affect your statutory rights.
When the power on indicator light starts flashing the machine needs to be
descaled and it will continue to flash until the unit is descaled.
1
2
With the machine switched off, place a jug under the steam/hot water nozzle.
(This may need to be emptied during the descaling process.)
Fill the water tank to the Max level with a liquid descaling agent (follow the
manufacturers guidelines).
3
4
Fit the pod filter holder (with pod filter fitted) to the coffee maker.
Press the power on button. Both the power on and OK indicator lights will
flash.
5
When the OK indicator light stops flashing, turn the function lever to the lower
steam position ( ).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
trouble shooting guide
symbol
warning signs
possible cause
solution
OK and steam indicator
flash alternately
Lack of water
Refill the water tank
The steam indicator light flashes
quickly
The memory is corrupted
The coffee maker needs repairing
see ‘service and customer care’.
The coffee maker can still be used
but the dispensing volumes will
default to factory settings and
cannot be adjusted. Also the
descaling mode will be lost.
Descale the machine.
The power indicator flashes
The machine needs to
be descaled.
The power indicator and
OK indicator flash alternately
The pod filter holder
is missing
Fit the filter into the filter
holder
The power, OK and
steam indicator
lights flash
The temperature of the
boiler is too high
Switch off the machine for a
period of time and re-start it
again. If the problem persists
return the appliance to a
Kenwood authorised repairer.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Kenwood Limited, New Lane, Havant, Hampshire PO9 2NH, UK
57773/2
Download from Www.Somanuals.com. All Manuals Search And Download.
|