DUAL DIN SIZED CD RECEIVER
DPX-MP5110U
DPX-MP4110
DPX-MP3110
INSTRUCTION MANUAL
© B64-4186-00/00 (MW)
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• The characters which can be displayed by this unit
are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ; ^ - { } |
~ .
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
2WARNING
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
<Demonstration mode Setting> (page 16).
How to reset your unit
• If this unit or the connected unit (disc auto changer,
etc.) fails to operate properly, press the Reset button.
The unit returns to factory settings when the Reset
button is pressed.
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
Reset button
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
CDs that cannot be used
• CDs that are not round cannot be used.
¤
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not been
finalized. (For the finalization process refer to your
CD-R/CD-RW writing software, and your CD-R/CD-
RW recorder instruction manual.)
English
|
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
DSI indicator Display
Disc slot
DPX-MP5110U
ꢂ
[
]
[SRC]
[SE]
[M.JOG]
[COL]
ꢀꢁ
[
]
USB Terminal
Auxiliary input
[1] [2] [3] [4] [5] [6]
[ATT]
Control knob
Muting volume upon reception of phone call
When there is a call, “CALL” is displayed and the audio
system is paused.
When the call ends, “CALL” disappears and the audio
system comes back on.
The audio system comes back on when [SRC] is
pressed during a call.
General functions
Power/Source Select button
Turns on the power.
[SRC]
When the power is on, the source switches between
Tuner (“TUNER”) , Tape** (“TAPE“) , USB* (“USB”),
CD (“CD”) , Auxiliary input (“AUX”), and Standby
(“STANDBY”) each time this button is pressed.
Press at least 1 second to turn off the power.
Subwoofer output
Control knob
Switches between ON (“SW On”) and OFF (“SW
Off”) each time pushing toward down for at least 2
seconds.
* Function of DPX-MP5110U.
** Function of DPX-MP4110.
⁄
•
•
•
When the power is ON, the <Security Code> (page 14) is
displayed as “Code On” or “Code Off”.
Tuner functions
For whether USB devices can be connected, refer to <About
Audio file> (page 18).
When an optional accessory is connected, the source name
for each device appears.
Band select
Control knob
Switches between FM1, FM2, and FM3 each time
pushing toward up.
Switches to AM when pushing toward down.
Volume control
Control knob
Turn the knob to adjust the volume.
Tuning
Control knob
Changes the frequency when pushing toward left or
right.
Attenuator
Turning the volume down quickly.
[ATT]
⁄
Auxiliary input
Connect a portable audio device with mini-plug cable
(3.5 ø).
Auxiliary input
•
During reception of stereo stations the “ST” indicator is ON.
Preset memory
[1] - [6]
Memorize the station selected when pressing for at
least 2 seconds.
⁄
•
Use the mini-plug cable which is stereo type and does not
have any resistance.
Preset tuning
[1] - [6]
Recalls the memorized station.
|
4
DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
: Indicates the button etc. to operate.
Disc & Audio file play functions
Folder search
Control knob
Changes the folder containing the audio file when
pushing toward up or down.
Disc play
Starts playing when a disc is inserted.
Disc slot
When a CD is inserted, the
indicator is ON.
Select mode
[M.JOG]
After pressing this button, you can quickly search
songs with the control knob. See <List Select> (page
12) for details.
⁄
•
3 inch (8 cm) CD cannot be used. Attempt to insert using
an adapter can cause malfunction.
Track/ File/ Folder repeat play
[4]
USB device play
USB Terminal
Switches between Track Repeat (“TRAC REP”) and OFF
(“REP Off”) when pressed while playing a CD.
Switches between File Repeat (“File REP”), Folder
Repeat (“FOLD REP”), and OFF (“REP Off”) when
pressed while playing an audio file.
Scan play
[2]
Successively plays the intro of the music in the disc or
folder.
When Scan Play is turned on, “TRAC SCN”/ “File SCN” is
displayed.
Random play
[3]
Connect the USB device to the USB cable (optional
accessory) which is connected to the USB terminal.
Randomly plays the music in the disc or folder.
When Random Play is turned on, “Disc RDM”/ “FOLD
RDM” is displayed.
When the USB device is connected, the
is ON.
indicator
Text/Title scroll
Control knob
⁄
Scrolls the CD and audio file text display when
pushing toward up for at least 2 seconds.
•
For the playable audio file, media, and devices, refer to
<About Audio file> (page 18).
Pause and play
Switches between pause and play each time this
button is pressed.
[38]
Disc ejection
[0]
⁄
•
You can eject the disc for 10 minutes after switching off the
engine.
USB device removing
[0]
Press this button for 2 seconds and longer to select
the remove mode, and the remove the USB device.
During the remove mode, “Remove” is displayed.
Music search
Control knob
Changes the music when pushing toward left or right.
Fast reverses or forwards the music while keeping
pushing toward left or right. (No sound is output
while playing audio file.)
Next page 3
English
|
5
Download from Www.Somanuals.com. All Manuals Search And Download.
: Indicates the button etc. to operate.
Basic Operation
Cassette tape slot
DSI indicator Display Disc slot
ꢂ
DPX-MP4110
[
]
[SRC]
[COL]
[SE]
[M.JOG]
ꢀꢁ
[
]
Tape ꢂ
[
]
[1] [2] [3] [4] [5] [6] Auxiliary input
[ATT]
Control knob
Cassette play functions
Dolby B NR
[1]
When Dolby B NR is ON, “B NR”indicator is ON.
Cassette play
Starts playing when a cassette tape is inserted.
When a Cassette is inserted, the indicator is ON.
Cassette tape slot
Scan play
[2]
Successively plays the intro of the music in the tape.
When Scan Play is turned on, “SCN” indicator is ON.
Direction
[38]
When you want to listen to the reverse side.
Blank Skip
[3]
Cassette tape ejection
Tape[0]
Fast forwarding automatically when an unrecorded
portion continues for at least 10 seconds.
Fast Forwarding and Rewinding
knob
Control
When the Blank Skip is turned on, “B.S”indicator is ON.
Fast Forwarding: Push the Control knob toward up.
Rewinding: Push the Control knob toward down.
Music repeat play
When Music repeat play is turned on, “REP” indicator is
ON.
[4]
DPSS (Direct Program Search System)
Control knob
Indicating the music to skip, and Fast Forwarding or
Rewinding.
Skipping to a later music: Push the Control knob
toward right.
Skipping to a previous music: Push the Control knob
toward left.
Selecting the Tape type
[6]
Display
Tape type
CrO2 (Type II), FeCr (Type III), Metal (Type IV) “MTL On”
Normal (Type I) “MTL Off”
When MTL is turned on, “MTL” indicator is ON.
⁄
•
Space between music and the first 5 seconds of the music
are recognized as the previous music.
•
As many as 9 music can be skipped.
|
6
DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
General Operation
Audio Control
Adjusting the detail of Audio Control
You can adjust following Audio Control items ;
Among the Basic Audio items, you can adjust the
Bass level, Middle level, and Treble level in detail.
Adjustment Item Display
Range
Bass level
Rear volume
Subwoofer level
System Q
“R-VOL”
“SW L”
0 — 35
–15 — +15
Adjustment Item
Display
Range
“User”/“Rock”/ User setting/Rock/Pops/Easy/
“Pops”/“Easy”/ Top 40/Jazz/Natural
“Top40”/“Jazz”/ (The indicator turns on
“Natural”
“BasLV”
“MidLV”
“TreLV”
“BAL”
Bass Center Frequency
”BasF”
40/50/60/70/80/100/
120/150 Hz
Bass Q Factor
Bass Extend
”BasQ”
”B EX”
1.00/1.25/1.50/2.00
Off/On
according to the setting.)
–8 — +8
–8 — +8
–8 — +8
Left 15 — Right 15
Rear 15 — Front 15
Bass level*
Middle level*
Treble level*
Balance
Middle level
Adjustment Item
Display
Range
Middle Center Frequency ”MidF”
0.5/1.0/1.5/2.0 kHz
1.0/2.0
Fader
“FAD”
Middle Q Factor
”MidQ”
Exit Audio Control mode (Volume control mode)
Treble level
Adjustment Item
Treble Center Frequency "TreF"
⁄
Display
Range
10.0/12.5/15.0/17.5 kHz
•
“USER”: The customized Bass, Middle, and Treble levels
are effective. This item can be selected at any time.
* You can adjust these items in detail. Refer to <Adjusting
the detail of Audio Control> (Page 7).
* Source tone memory: Puts the set up value in the
memory per source. (Detail Audio item is included)
⁄
•
When you set the Bass Extend to ON, low frequency
response is extended by 20%.
•
You can exit the Audio Control mode at anytime by
pressing any button except for Control knob and [ATT]
button.
1 Select the source to adjust
Press the [SRC] button.
1 Select the Basic Audio item
Select the desired item to be set in detail from
followings;
• Bass level
• Middle level
2 Enter Audio Control mode
Press the Control knob.
3 Select the Audio item to adjust
Press the Control knob.
• Treble level
For how to select Basic Audio items, see <Audio
Control> (page 7).
4 Adjust the Audio item
Turn the Control knob.
5 Exit Audio Control mode
Press any button.
Press a button other than the Control knob.
2 Enter Detail adjustment mode of Audio
Control
Press the Control knob for at least 1 second.
3 Select the Detail Audio item to adjust
Press the Control knob.
4 Adjust the Detail Audio item
Turn the Control knob.
5 Exit the Detail Audio Control mode
Press the Control knob for at least 1 second.
English
|
7
Download from Www.Somanuals.com. All Manuals Search And Download.
General Operation
Audio Setup
Speaker Setting
You can set Sound system, such as follows;
Fine-tuning so that the System Q value is optimal
when setting the speaker type as follows;
Adjustment Item
Display
Range
Front High Pass Filter “HPF”
Through/40/60/80/100/120/
Speaker type
OFF
For 5 & 4 in. speaker
For 6 & 6x9 in. speaker
For the OEM speaker
Display
“SP Off”
“SP 5/4”
“SP 6*9/6”
“SP OEM”
150/180/220 Hz
Rear High Pass Filter “HPR”
Through/40/60/80/100/120/
150/180/220 Hz
50/60/80/100/120/Through Hz
Reverse (180°)/ Normal (0°)
–8 — 0 (AUX: -8— +8)
Off/On
Low Pass Filter
Subwoofer Phase
Volume offset
Loudness
“LPF”
“PHAS”
“V-Off”
“LOUD”
“2ZON”
1 Enter Standby
Press the [SRC] button.
Dual Zone System
Off/On
Select the “STANDBY” display.
2 Enter Speaker Setting mode
Press the Control knob.
“SP SEL” is displayed.
⁄
•
Volume offset: Sets each source’s volume as a difference
from the basic volume.
•
Loudness: Compensates for low and high tones during
low volume. (Only the low tone is compensated for
when the tuner is selected as a source.)
Dual Zone System
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
- Set up the channel of sub source by “Zone2” of <Menu
System> (page 14).
3 Select the Speaker type
Turn the Control knob.
•
4 Exit Speaker Setting mode
Press the Control knob.
- Select Main source by [SRC] button.
Sound Enhancer Select
You can play back adding gorgeous heavy bass to
the sound.
- Adjust the volume of Front channel by Control knob.
- Adjust the volume of Rear channel by <Audio Control>
(page 7).
- The Audio Control has no effect on sub source.
1 Enter the Sound Effect mode
Press the [SE] button.
1 Select the source to adjust
Press the [SRC] button.
"SE SEL" is displayed.
2 Enter Audio Setup mode
2 Select the Sound effect item
Press the Control knob for at least 1 second.
Turn the Control knob.
3 Select the Audio Setup item to adjust
Sound effect
Returns to the normal sound without Sound effect.
Moves the sound image up a notch and adjusts bass.
Moves the sound image up two notches and adjusts “SE High“
bass.
Display
“SE Off“
“SE Low”
Press the Control knob.
4 Adjust the Audio setup item
Turn the Control knob.
5 Exit Audio Setup mode
Changes to the value set in <Sound Enhancer
Control>(page 9).
“SE User“
Press the Control knob for at least 1 second.
When the Sound effect is ON, the “SE“ indicator is
ON.
3 Exit the Sound Effect mode
Press the [SE] button.
|
8
DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Enhancer Control
Adjusts each function of Sound effect individually.
⁄
•
Scan of Spectrum Analyzer:
The items from “PeakHold” to “Jump” are displayed in
sequence.
1 Enter the Sound Effect Control mode
Press the [SE] button for at least 1 second.
“SE CTRL” is displayed.
2 Select the Sound effect item for adjustment
Illumination Color Select
Select the illumination color for display, buttons
and control knob.
Push the Control knob towards right or left.
3 Adjust the Sound effect item
Push the Control knob towards up or down.
1 Enter the Illumination color Select mode
Press the [COL] button.
“Color” is displayed.
Adjustment Item
Bass setting
LV setting
Display
“Bas”
“LV”
Range
Off/Low/High
Off/Low/High
2 Select the setting item
4 Exit the Sound Effect Control mode
Push the Control knob towards right or left.
Press the [SE] button.
Display
“All”
“Display”
“Key”
Setting item
Sets the same color for all of items.
Sets the display color.
⁄
•
•
Bass: Assisting the playback for the super bass sound.
LV: Adjusts the sound image by changing the vertical
position of the speakers virtually and increases or
decreases the soundscape.
Sets the button color.
“Rotary”
Sets the control knob color.
3 Change the color
Turn the Control knob.
Color setting
Scan of Color 1-10
Color 1
Display
”V.Scan”
”Color 1”
”Color 2”
Spectrum Analyzer Select
Selecting the Spectrum Analyzer display.
Color 2
Spectrum Analyzer
Scan of Spectrum Analyzer
Peak Hold
Display
“S.A Scan“
“PeakHold“
“Flash“
“Meter“
“Gravity“
“Tension“
“Hana-Bi“
“Laser”
Color 10
User color
”Color 10”
”User”
Spectrum Analyzer 1
Spectrum Analyzer 2
Spectrum Analyzer 3
Spectrum Analyzer 4
Spectrum Analyzer 5
Spectrum Analyzer 6
Spectrum Analyzer 7
Spectrum Analyzer 8
Spectrum Analyzer 9
Spectrum Analyzer off
4 Exit the Illumination color Select mode
Press the [COL] button.
⁄
•
•
•
You can adjust the illumination color to your taste using
RGB setting. See <User Color Setting> (page10) for detail.
When illumination effect (I-EFCT) setting (page 14) is “2“,
you can not set color.
When illumination effect (I-EFCT) setting (page 14) is “3“,
you can select “ALL“ and set “color1” to “10”.
“Dance“
“Warp“
“Jump“
“S.A Off“
1 Enter the Spectrum Analyzer Select mode
Press the [COL] button for at least 1 second.
“SPEANA” is displayed.
2 Select the Spectrum Analyzer
Turn the Control knob.
3 Exit the Spectrum Analyzer Select mode
Press the [COL] button.
English
|
9
Download from Www.Somanuals.com. All Manuals Search And Download.
General Operation
In Tape source
User Color Setting
Information
Play time (Tape counter)
Clock
Display
“Counter”
“Clock”
Adjust the illumination color with R(Red), G(Green),
B(Blue) setting. Adjusted set value is memorized in
the <Illumination color Select> of User setting area.
Graphic
“Graphic”
1 Select the item to adjust and select “USER”
See step1 to step3 of <Illumination Color Select>
(page 9) for detail.
In Standby/ Auxiliary input source
Information
Source name
Clock
Display
“SRC Name”
“Clock”
2 Enter the RGB adjusting mode
Press the Control knob for at least 1 second.
Graphic
“Graphic”
3 Select the color to adjust
Push the Control knob towards right or left.
Adjust the blinking color.
1 Enter Switching Display mode
Press the [38] button for at least 1 second.
4 Adjust the RGB Color
“DISP SEL” is displayed.
Turn the Control knob.
2 Select the Display item
5 Exit the RGB adjusting mode
Push the Control knob towards up or down.
Press the Control knob.
3 Exit Switching Display mode
Press the [38] button.
⁄
•
When you select the clock display, the display setting of
each source will be changed to the clock display.
If the selected display item does not have any
information, alternative information is displayed.
Display Switching
Changing displayed information on each source
following;
•
In Tuner source
Information
Frequency
Clock
Display
“FREQ”
“Clock”
Graphic
“Graphic”
In CD & External disc source
Information
Disc title
Track title (In External disc source)
Play time & Track number
Display
“D-Title”
“T-Title”
“P-Time”
“Clock”
Clock
Graphic
“Graphic”
In Audio file source
Information
Display
“Title”
“Album”
“Folder”
“File”
Music title & Artist name
Album name & Artist name
Folder name
File name
Play time & Music number
Clock
Graphic
“P-Time”
“Clock”
“Graphic”
|
10 DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner Operation
Auto Memory Entry
Frequency Step Setting
Putting stations with good reception in the memory
automatically.
Changing the tuning frequency step.
The original setting is FM band 50 kHz, and AM
band 9 kHz.
1 Select the band for Auto Memory Entry
Push the Control knob towards up or down.
1 Turn the power OFF
Press the [SRC] button for at least 1 second.
2 Enter Menu mode
Press the [M.JOG] button for at least 1 second.
“Menu” is displayed.
2 Switch the frequency step
While pressing the [1] and [5] buttons, press the
[SRC] button.
Release your fingers from the button after the
display appears.
3 Select the Auto Memory Entry mode
Push the Control knob towards up or down.
Select the “A-Memory” display.
The frequency step changes to FM band 200 kHz,
and AM band 10 kHz.
4 Open Auto Memory Entry
Press the Control knob for at least 1 second.
When 6 stations that can be received are put in the
memory, Auto Memory Entry closes.
⁄
•
When the same operation is repeated, the frequency
step returns to the original setting.
•
When the frequency step is changed, the frequencies in
the memory are deleted.
Function of remote control
Direct Access Tuning
Entering the frequency and tuning.
1 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
“– – – –” is displayed.
2 Enter the frequency
Press the number buttons on the remote
control.
Example:
Desired frequency
92.1 MHz (FM)
810 kHz (AM)
Press button
[0], [9], [2], [1]
[0], [8], [1], [0]
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
⁄
•
You can enter the FM band frequency in steps of a
minimum of 0.1 MHz.
•
If you make no button operation for 10 seconds, this
function is automatically canceled.
English
|
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Music disc/Audio file Operation
Function of disc changers with remote control
Play Functions of Disc Changer
While a disc in the disc changer is being played, the
following play functions can be used.
Direct Disc Search
Doing Disc Search by entering the disc number.
Playing the Current Song or Disc Repeatedly.
(Repeat play)
Press the [4] button.
1 Enter the disc number
Press the number buttons on the remote
control.
Pressing the button repeatedly selects Track Repeat
play on (“TRAC REP”), Disc Repeat play on (“Disc
REP”), and Repeat play off (“REP Off”) sequentially.
2 Do Disc Search
Press the [FM] or [AM] button.
Cancelling Direct Disc Search
Press the [38] button.
⁄
Randomly plays the music in the disc changer.
(Magazine random play)
Press the [6] button.
Pressing the button toggles the setting between
Magazine random play on (“MGZN RDM”) and off
(“RDM Off”).
•
•
Input “0” to select disc 10.
Direct Disc Search cannot be performed during playing
of Random play or scan play.
Function of USB/CD of Audio file
Function of remote control
List Select
Search for the song you want to listen to by tracing
the media file structure.
Direct Music Search
Doing Music Search by entering the music number.
1 Enter the music number
Press the number buttons on the remote
control.
1 Enter Multi Jog Select mode
Press the [M.JOG] button.
“M. Jog On” is displayed.
2 Do music Search
Displays the current Audio file name.
Press the [4] or [¢] button.
2 Searching for and playing a song
Cancelling Direct Music Search
Press the [38] button.
Operation type
Movement between
folders/files
Operation
Turn the Control knob.
⁄
Selection of folder/flie
Press the Control knob.
•
Direct Music Search cannot be performed during
Random play or scan play.
Return to previous folder Push the Control knob towards left.
Return to root folder
Push the Control knob towards left for at
least 1 second.
•
If you make no button operation for 10 seconds, this
function is automatically canceled.
Cancelling the Multi Jog Select mode
Press the [M.JOG] button.
⁄
•
List Select cannot be performed during Random play or
scan play.
|
12 DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
Cassette Operation
Function of Music CD
DPSS with the Remote control
Designating the music to be skipped with the
remote control number buttons.
Track Select
Select the song you want to listen to by turning the
control knob.
1 Designate the music to skip
Press number buttons on the remote.
1 Enter Multi Jog Select mode
Press the [M.JOG] button.
“M. Jog On” is displayed.
2 Skipping to a later music
Press the [¢] button.
Displays the current music No.
Skipping to a previous music
Press the [4] button.
2 Select the music
Turn the Control knob.
Cancelling DPSS
Press the [38] button.
3 Play the selected song
Press the Control knob.
⁄
The Multi Jog Select mode is canceled and the
selected song is played.
•
If you make no button operation for 10 seconds, this
function is automatically canceled.
Cancelling the Multi Jog Select mode
Press the [M.JOG] button.
⁄
•
Track Select is available only during playing of the built-
in CD player.
•
Track Select cannot be performed during Random play
or scan play.
English
|
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operation
Menu System
Set up the following functions;
: Can be set during Tuner reception.
: Can be set while accessing AUX source.
: Can be set during all sources.
—
Display
“Code Set” Refer to
page 14
Setting Setting overview
Source
1 Enter Menu mode
Sets security code.
Press the [M.JOG] button for at least 1 second.
“Menu” is displayed.
—
“I-EFCT”
0/1/2/3
Set the illumination color effect.
(page 19)
2 Select the Menu item
Push the Control knob towards up or down.
“Beep”
On*/Off
Setting the operation check
sound (beep sound) ON/OFF.
3 Set the Menu item
“CLK ADJ” Refer to
page 15
“DSI”
Sets the clock.
Push the Control knob towards right or left.
4 Exit Menu mode
On*/Off
A red indicator will blink on the
unit after the ACC is set to OFF,
warning potential thieves.
Press the [M.JOG] button.
⁄
“CONT“
1— 5*— Adjusting the display contrast.
11
•
•
•
•
Refer to the respective page for information on how to
set the items with reference page number.
”Zone2” is displayed when ”2ZON” in <Audio Setup>
(page 8) is set to ”ON.
Refer to the <Appendix> (page 18) for the details of the
menu items.
Strong electrical fields (such as from power lines) may
cause unstable sound quality when CRSC is turned ON.
In such a situation, turn it OFF.
“SWPRE”
“Zone2”
R*/SW
Sets the preout output.
R*/F
Specifies the destination of AUX
input sound when the Dual Zone
function is turned on.
“AMP”
“SPRM”
“Auto”
On*/Off
On*/Off
Turns on/off the built-in
amplifier.
Turns ON/OFF the Supreme
function.
Auto1*/ Selects the tuning mode of
Security Code
When Security Code is set, possibility of theft
is reduced because input of Security Code is
prompted to turn on the unit once it is turned off.
Auto2/
Manual
the radio.
“A-Memory” Refer to
page 11
Putting stations with good
reception in the memory
automatically.
“CRSC”
Off/On*
Switches to Monaural to decrease
noise when reception is poor.
Sets the display when switched
to AUX source.
⁄
•
When you activate the Security Code function, it cannot be
released.
“Name Set” Refer to
page 15
Note, your Security Code is the 4 digit number entered in
your “Car Audio Passport” in this package.
—
—
“SCL”
Auto*/
MANU
Off/On*
Specifies whether the text is
scrolled automatically.
Sets whether to display AUX
during source selection.
1 Select Security Code item during Menu mode
Select the “Code Set” display.
For how to select menu items, refer to <Menu
System>(page 14).
“AUX”
“CD Read” 1*/2
Sets the CD read mode.
2 Enter Security Code mode
“DEMO”
Refer to
page 16
Specifies whether to enable
demonstration.
Press the Control knob for at least 1 second.
When “Enter” is displayed, “Code” is also displayed.
*Factory setting
Displayed item is depending on currently selected source.
The mark in Source column shows the source to which the
item is displayed.
3 Select the digits to enter
Push the Control knob towards right or left.
4 Select the Security Code numbers
: Can be set in other than standby state.
: Can be set in standby state.
Push the Control knob towards up or down.
: Can be set while Audio file source of CD/USB.
: Can be set during FM reception.
5 Repeat step 3 and 4, and complete the Security
Code.
|
14 DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Confirm the Security Code
Press the Control knob for at least 3 seconds.
When “RE-Enter” is displayed, “Code” is also
displayed.
3 Adjust the time
Push the control knob towards up or down to
adjust the hours and right or left to adjust the
minutes.
7 Do the step 3 through 6 step operation, and
reenter the security code.
“Approved” is displayed.
4 Exit Clock adjustment mode
Press the [M.JOG] button.
The Security Code function activates.
⁄
Auxiliary Input Display Setting
Selecting the display below when changing to
Auxiliary input source;
•
If you enter a Code different from your Security Code,
you have to start over from step 3.
8 Exit Security Code mode
Press the [M.JOG] button.
• “AUX”
• “DVD”
Entering Security Code
• “PORTABLE”
• “GAME”
• “VIDEO”
• “TV”
The Security Code is required to use the audio unit
when the unit is first used after removed from the
battery power source or the Reset button is pressed.
1 Turn the power ON.
1 Select Auxiliary input display setting item
during Menu mode
Select the “Name Set” display.
For how to select menu items, refer to <Menu
System>(page 14).
2 Do the step 3 through 6 step operation, and
reenter the security code.
“Approved” is displayed.
⁄
•
If an incorrect code is entered, “Waiting” is displayed, and
the input prohibition periods shown in the table below
is generated.
2 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The presently selected Auxiliary input display is
displayed.
After the input prohibition time lapses, “Code” is
displayed, and you can reenter the code.
3 Select the Auxiliary input display
Number of times the
incorrect code was input
Input prohibited time
Push the Control knob towards up or down.
1
2
3
4
—
5 minutes
1 hour
4 Exit Auxiliary input display setting mode
Press the [M.JOG] button.
⁄
24 hours
•
When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.
•
The Auxiliary input display can be set only when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used. On the KCA-S220A, “AUX EXT” is
displayed by default.
Manual Clock Adjustment
1 Select Clock Adjustment item during Menu
mode
Select the “CLK ADJ” display.
For how to select menu items, refer to <Menu
System>(page 14).
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second.
The clock display blinks.
English
|
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operation
Basic Operations of remote control
Demonstration mode Setting
Turning the demonstration mode ON/OFF.
SRC
VOL
ATT
1 Select Demonstration item during Menu mode
Select the “DEMO” display.
AUD
For how to select menu items, refer to <Menu
System>(page 14).
FM/AM/+/–
2 Set the Demonstration mode
Press the Control knob for at least 2 second.
Pressing this button for 2 seconds or longer toggles
the setting between ”On” and ”Off”.
DIRECT
2-ZONE
0 — 9
3 Exit Demonstration mode
Press the [M.JOG] button.
General control
Volume control
Source select
Volume reduce
[VOL]
[SRC]
[ATT]
When the button is pressed again, the volume returns
to the previous level. When the volume is reduced,
the "ATT" indicator flashes.
In Audio control
Audio item select
[AUD]
[VOL]
Adjusts the Audio item
⁄
•
Refer to <Audio Control> (page 7) for the operation
method, such as the procedures for Audio control and
others operations.
•
The remote control can only select and adjust the Basic
Audio item. Selecting and adjusting of the Detail Audio
item cannot be done.
|
16 DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
Dual Zone control
⁄
About [
]
This button is used when Bluetooth HANDS FREE
BOX is connected. For more information, refer to the
instruction manual of Bluetooth HANDS FREE BOX.
Dual zone system on and off
Rear channel volume control
[2-ZONE]
[5]/ [∞]
¤
In Tuner source
• Do not set the remote control in hot places such as
on the dashboard.
Band select
[FM]/[AM]
Loading and Replacing the battery
Use two “AA”/ “R6”-size batteries.
Slide the cover while pressing downwards to remove
it as illustrated.
Insert the batteries with the + and – poles aligned
properly, following the illustration inside the case.
Station select
[4]/[¢]
Recall preset stations
[1] — [6]
In CD/USB source
Music select
[4]/[¢]
[FM]/[AM]
Folder/Disc select
Pause/Play
[38]
In Cassette tape source
DPSS
[4]/[¢]
Fast forwards/Rewinds
[FM]/[AM]
Direction
[38]
DPSS
[0] — [9]
⁄
When in <DPSS with the Remote control> (page
13), enter the number of music.
English
|
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
About Audio file
About USB device
•
•
•
•
•
Playable Audio file
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
USB device Playable Model
DPX-MP5110U
Playable USB device
USB mass storage class
Playable USB device file system
FAT16, FAT32
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
• When connecting the USB device, usage of the CA-
U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
•
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
<
v
:
FFolldderr
Audiofile
CD
(ꢂ)
:
vꢀ
ꢁ
About Cassette tape
Cleaning the tape head
ꢃ
When there’s noise or the sound quality is bad during
tape play the tape head maybe dirty, clean the tape
head.
vꢆ
vꢇ
ꢅ
vꢄ
ꢈ
vꢉ
v.
About Cassette tape
• If the tape is slack tighten it.
• If the cassette tape label is peeling off glue it on
again.
• Don’t use deformed cassette tape.
• Don’t place cassette tape on the dashboard etc.
where the temperature is high.
• Don’t use cassette tape that’s 100 minutes long or
longer.
An online manual about audio files is put on the
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
⁄
•
In this manual, the word "USB device" is used for flash
memories and digital audio players which have USB
terminals.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says
that the component uses laser beams that have
been classified as Class 1. This means that the unit is
utilizing laser beams that are of a weaker class. There
is no danger of hazardous radiation outside the unit.
|
18 DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Glossary
For operating KCA-BT100
•
SWPRE (Switching Preout)
To control KCA-BT100, operate as follows;
Switches the preout between rear output (“R”) and
subwoofer output (“SW”).
SUPREME
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range
that is cut off when encoding at low bit rate (less
than 128Kbps, Sampling frequency is 44.1kHz).
Supplementing is optimized by compression
format (AAC, MP3 or WMA) and processed
according to bit rate.
To make setting for <Selecting the Dialing Mode>,
select <Menu System> (page 14). Pressing the [ATT]
button at least 1 second after selecting the “DIALING
MODE” item allows you to enter the dialing method
selection mode. To exit from dialing method selection
mode, press [ATT] button at least 1 second.
To make <Disconnecting a Call>, <Clearing the
Disconnection Message>, and <Rejecting an
Incoming call>, press [ATT] button for at least 1
second.
•
The effect is negligible with music that is encoded
at high bit rate, variable bit rate or has minimal high
frequency range.
CD READ
Sets the method for reading CD.
When unable to play special format CD, set this
function to “2” to force playing. Note that some
music CD may be unplayable even when set to “2”.
In addition, audio files cannot be played when set
to “2”. Normally, keep this set to “1”.
1 : Automatically distinguishes between audio file
disc and music CD when playing disc.
2 : Forces playing as music CD.
Moreover, some displays are different from the
description of KCA-BT100 Instruction Manual.
Displays of KCA-BT100 Instruction Actual displays on this unit
Manual
•
“DISCONCT”
“CONNECT”
“PHN-DEL”
“P-STATUS”
“BT-CON Y”
“BT-CON N”
“HF D-CON”
“HF CON”
“DVC-DEL”
“D-Status”
“HF-CON Y”
“HF-CON N”
: Displays the bluetooth connection status.
This indicator turns on when a cell-phone is
connected to this unit.
: Displays the signal strength of cell-phone.
: Displays the battery level of cell-phone.
•
•
•
ZONE2 (Dual Zone)
Set the destination (front speaker “F” or rear speaker
“R”) of the sub source (AUX IN) when the Dual Zone
function is turned on.
AMP
Selecting “Off” turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
AUTO (Tuning mode select)
Select a tuning mode of the radio.
Tuning mode
Auto seek
Display Operation
“Auto1” Automatic search for a station.
Preset station seek “Auto2”
Search in order of the stations in the
Preset memory.
Manual
“Manual” Normal manual tuning control.
•
I-EFCT (Illumination effect)
Set the illumination color effect.
Illumination effect mode
Display
Mode off
“0”
Illumination color will change to variable, each time this “1”
unit is operated.
Illumination color will be mono-color and then
illumination color will change variable with the playback
tone of sound.
“2”
Illumination color will be mono-color and then
illumination brightness will change with the playback
tone of sound.
“3”
English
|
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories/ Installation Procedure
•
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“Protect” is displayed), the
speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
Accessories
•
1
..........1
•
2
..........1
•
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
•
3
•
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
..........6
•
4
..........6
•
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
•
•
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
About CD players/disc changers connected
to this unit
Kenwood disc changers/ CD players released in 1998
or later can be connected to this unit.
Refer to the catalog or consult your Kenwood dealer
for connectable models of disc changers/ CD players.
Note that any Kenwood disc changers/ CD players
released in 1997 or earlier and disc changers made by
other makers cannot be connected to this unit.
Connecting unsupported disc changers/CD players to
this unit may result in damage.
Set the “O-N” Switch to the “N” position for the
applicable Kenwood disc changers/ CD players.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
|
20 DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Wires to Terminals
Steering remote control (Light Blue/Yellow)
REMO.CONT
To use the steering wheel remote control feature, you need to an exclusive
remote adapter (not supplied) matches your car is required.
When this terminal is not in use, leave its cap on.
FM/AM antenna input
Front preout
Rear/SubWoofer preout
Fuse (10A)
To Kenwood disc changer/
External optional accessory
Wiring harness
(Accessory1)
If no connections are made, do not let the wire come out from the tab.
Power control/Motor antenna control wire
(Blue/White)
Connect either to the power control terminal when using
the optional power amplifier, or to the antenna control
terminal in the vehicle.
P.CONT
TEL mute wire (Brown)
Connect to the terminal that is grounded when either the
telephone rings or during conversation.
MUTE
⁄
To connect the Kenwood navigation system, consult
your navigation manual.
Motor antenna control wire (Blue)
Depending on what antenna you are using, connect either
to the control terminal of the motor antenna, or to the
power terminal for the booster amplifier of the film-type
antenna.
ANT.
CONT
Dimmer control wire (Orange / White)
To car light control switch
ILLUMI
White/Black
To front left speaker
White
Gray/Black
To front right speaker
Gray
Green/Black
To rear left speaker
Green
Purple/Black
Ignition key switch
To rear right speaker
Purple
Car fuse box
ACC
Ignition wire (Red)
Battery wire (Yellow)
Car fuse box
(Main fuse)
Ground wire (Black) - (To car chassis)
+
–
Battery
English
|
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
Install onto the car bracket using the supplied screws
(M5 × 6 mm, M5 × 7 mm). The holes of the car
bracket to use will differ depending on the car model.
Car Bracket
Accessory3 (M5 × 7 mm)
or Accessory4(M5 × 6 mm)
Accessory2
(Only for NISSAN car)
|
22 DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
Audio file source
? The sound skips when an Audio file is being
played.
!
• Cannot set up the subwoofer.
• Cannot set up the High Pass Filter.
• Cannot set up the Fader.
✔
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 3).
• No Audio control effect on AUX.
• Preout is not set to subwoofer. ☞ “SWPRE” of
<Menu System> (page 14)
• “Subwoofer output” of <Baisc Operatiom> (page 4)
is not set to On.
The recording condition is bad.
Record the media again or use another media.
☞
? Noise is heard when carrying out Folder Search.
✔
Noise may be produced if folders without audio files
exist continuously in the playing media.
• The Dual zone function is enabled. ☞ <Audio
Setup> (page 8)
☞
Do not make folders without audio files.
Cassette tape source
!
!
• Cannot set up the subwoofer phase.
The Low Pass Filter is set to Through. ☞ <Audio
Setup> (page 8)
? The sound quality is poor or distorted.
✔
The tape head is dirty.
☞
Clean the tape head.
• Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
The Dual zone function is disabled. ☞ <Audio
Setup> (page 8)
? The DPSS, Tape Advance and Music Repeat don’t
operate correctly.
✔
The space between the songs on the tape can’t be
recognized because it’s too short.
☞
Have at least 5 seconds between songs.
✔
The space between songs can’t be recognized
because there’s too much noise between songs.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
☞
Reduce the noise between songs.
? The blank skip doesn’t work.
✔
Because noise is too loud, the non-recorded part
can’t be recognized.
☞
Reduce the noise between songs.
Tuner source
? Blank Skip functions at places that are recorded.
? Radio reception is poor.
✔
Because the recording level is low, it’s recognized as
not recorded.
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
☞
Turn Blank Skip OFF.
Disc source
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
Clean the CD.
The disc is loaded in a different slot from that
specified.
☞
☞
Eject the disc magazine and check the number
for the specified disc.
✔
The disc is severely scratched.
Try another disc instead.
☞
English
|
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
NA File:
An Audio file is played with a format that this
unit can’t support.
The messages shown below display your
systems condition.
Copy PRO:
Reading:
Hold:
A copy-protected file is played.
Eject:
• No disc magazine has been loaded in
the changer. The disc magazine is not
completely loaded.
The unit is reading the data on the disc.
• No CD in the unit.
The protective circuit in the unit activates
when the temperature inside the automatic
disc changer exceeds 60°C (140°F), stopping
all operation.
➪ Cool down the unit by opening the
windows or turning on the air conditioner.
As the temperature falls below 60°C
(140°F), the disc will start playing again.
No Disc:
TOC ERR:
No disc has been loaded in the disc
magazine.
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
READ Error:
The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
E-05:
E-77:
The disc is unreadable.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the “E-
77” code does not disappear, consult your
nearest service center.
No Device:
NA Device:
The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
E-99:
Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
➪ Check the disc magazine. And then press
the reset button on the unit. If the “E-99”
code does not disappear, consult your
nearest service center.
An unsupported USB device is connected.
➪ Remove the USB device without entering
the remove mode.
(Blink):
The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
No Music/E-15: • The connected USB device contains no
playable audio file.
• Media was played that doesn’t have data
recorded that the unit can play.
USB ERR/
(Blink):
Some trouble may have occurred to the
connected USB device.
➪ Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
(Blink):
The tape player section is not operating
properly.
➪ Reinsert the Tape. If the tape cannot be
ejected or the display continues to flash
even when the tape has been properly
reinserted, please switch off the power
and consult your nearest service center.
Remove:
The Remove mode has been selected for the
USB device. You can remove the USB device
safely.
Protect:
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
|
24 DPX-MP5110U/DPX-MP4110/DPX-MP3110
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
MP3 decode
FM tuner section
Frequency range
200 kHz space : 87.9 MHz – 107.9 MHz
50 kHz space : 87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 30dB)
: 9.3dBf (0.8 μV/75 Ω)
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC ".m4a" files
Quieting Sensitivity (S/N = 50dB)
: 15.2dBf (1.6 μV/75 Ω)
Frequency response ( 3 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
: 70 dB
Selectivity ( 400 kHz)
: ≥ 80 dB
Cassette player section (DPX-MP4110)
Tape speed
: 4.76 cm/sec.
Wow & Flutter (WRMS)
: 0.1 %
Frequency response (70 μs)
: 40 Hz – 20 kHz ( 3 dB)
Separation (1 kHz)
: 35 dB
Stereo separation (1 kHz)
: 40 dB
Signal to Noise ratio
Dolby NR Off : 50 dB
Dolby B NR On : 60 dB
AM tuner section
Frequency range
10 kHz space : 530 kHz – 1700 kHz
9 kHz space : 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB)
: 28 dBμ (25 μV)
Audio section
Maximum output power
: 50 W x 4
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
CD player section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Speaker Impedance
: 4 – 8 Ω
Tone action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout level / Load (CD)
: 2500 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
Frequency response ( 1 dB)
Auxiliary input
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
: 0.008 %
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
Signal to Noise ratio (1 kHz)
: 105 dB
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
General
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC ".m4a" files
Operating voltage (11 – 16V allowable)
: 14.4 V
Current consumption
: 10 A
Installation Size (W x H x D)
USB Interface (DPX-MP5110U)
USB Standard
: USB1.1/ 2.0
: 178 x 100 x 155 mm
Weight
: 1.60 kg (DPX-MP5110U)
: 1.95 kg (DPX-MP4110)
: 1.55 kg (DPX-MP3110)
Maximum Supply current
: 500 mA
File System
: FAT16/ 32
Specifications subject to change without notice.
English
|
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|