Kenwood Car Stereo System DPX MP2090U User Manual

CD-RECEIVER  
DPX-MP2090U  
INSTRUCTION MANUAL  
© B64-3433-00/00 (MW)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety precautions  
About CD players/disc changers  
connected to this unit  
Kenwood disc changers/ CD players released in  
1998 or later can be connected to this unit.  
Refer to the catalog or consult your Kenwood  
dealer for connectable models of disc changers/  
CD players.  
2WARNING  
To prevent injury or fire, take the  
following precautions:  
• To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools)  
inside the unit.  
Note that any Kenwood disc changers/ CD players  
released in 1997 or earlier and disc changers made  
by other makers cannot be connected to this unit.  
Connecting unsupported disc changers/CD players  
to this unit may result in damage.  
Set the "O-N" Switch to the "N" position for the  
applicable Kenwood disc changers/ CD players.  
The functions you can use and the information  
that can be displayed may differ depending on the  
models being connected.  
• Mounting and wiring this product requires  
skills and experience. For safety’s sake, leave the  
mounting and wiring work to professionals.  
2CAUTION  
To prevent damage to the machine, take  
the following precautions:  
• Make sure to ground the unit to a negative 12V  
DC power supply.  
• Do not install the unit in a spot exposed to direct  
sunlight or excessive heat or humidity. Also avoid  
places with too much dust or the possibility of  
water splashing.  
You can damage both your unit and the CD changer if  
you connect them incorrectly.  
• Do not subject the faceplate to excessive shock,  
as it is a piece of precision equipment.  
• When replacing a fuse, only use a new fuse with  
the prescribed rating. Using a fuse with the wrong  
rating may cause your unit to malfunction.  
• Do not use your own screws. Use only the screws  
provided. If you use the wrong screws, you could  
damage the unit.  
Lens Fogging  
When you turn on the car heater in cold weather,  
dew or condensation may form on the lens in the  
CD player of the unit. Called lens fogging, this  
condensation on the lens may not allow CDs to  
play. In such a situation, remove the disc and wait  
for the condensation to evaporate. If the unit still  
does not operate normally after a while, consult  
your Kenwood dealer.  
Do Not Load 8 cm (3 in.) CDs in the CD  
slot  
If you try to load a 8 cm (3 in.) CD with its adapter  
into the unit, the adapter might separate from the  
CD and damage the unit.  
The "AAC" logo is trademark of Dolby  
Laboratories.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
3
Notes  
• No USB device comes with this unit. You need to  
purchase a commercially available USB device. For  
the types of available USB devices, refer to <About  
USB device> (page 7).  
• If you experience problems during installation,  
consult your Kenwood dealer.  
Cleaning the Unit  
If the faceplate of this unit is stained, wipe it with a  
dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the stain off  
with a cloth moistened with neutral cleaner, then  
wipe it again with a clean soft dry cloth.  
• When you purchase optional accessories, check  
with your Kenwood dealer to make sure that they  
work with your model and in your area.  
• We recommend the use of <Activating Security  
Code> (page 26) to prevent theft.  
Applying spray cleaner directly to the unit may affect its  
mechanical parts. Wiping the faceplate with a hard cloth  
or using a volatile liquid such as thinner or alcohol may  
scratch the surface or erases characters.  
• The characters which can be displayed by this  
unit are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ;  
^ - { } | ~ .  
• The illustrations of the display and the panel  
appearing in this manual are examples used to  
explain more clearly how the controls are used.  
Therefore, what appears on the display in the  
illustrations may differ from what appears on the  
display on the actual equipment, and some of the  
illustrations on the display may be inapplicable.  
About "Media Manager" of PC application  
attached to DPX-MP2090U  
• "Media Manager" is recorded in the CD-ROM  
attached to this unit.  
• Refer to the attached installation manual for the  
installation method of "Media Manager".  
• Refer to the user’s manual recorded in the  
installation CD-ROM and Help of "Media Manager"  
for the operation method of "Media Manager".  
• The unit can play CD/ USB device (hereafter called  
"ACDrive media") created by "Media Manager".  
• Refer to the following site for the updated  
information of "Media Manager".  
• Contact Kenwood for the function and operation  
of the "Media Manager".  
How to reset your unit  
• If the unit fails to operate properly, press the Reset  
button. The unit returns to factory settings when  
the Reset button is pressed.  
• Remove the USB device before pressing the Reset  
button. Pressing the Reset button with the USB  
device installed can damage the data contained  
in the USB device. For how to remove the USB  
device, refer to <Playing USB device> (page 18).  
• "Media Manager" is a product of PhatNoise.  
• Press the Reset button if the disc auto changer  
fails to operate correctly. Normal operation should  
be restored.  
Reset button  
|
4
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About DAB Tuner control  
Refer to A group on the Instruction manual of DAB  
Tuner KTC-9090DAB (optional accessory) for the  
control method of DAB Tuner function.  
However, the following control methods of the  
function for this unit may be differed from the  
Instruction manual; therefore, refer to the following  
supplemental instruction.  
<Auto Ensemble Memory Entry>  
1. Select the preset band for Auto Ensemble  
Memory Entry.  
2. Press the [AME] button for at least 2 seconds.  
Open Auto Ensemble Memory Entry.  
After memory storage is finished, the number of  
the pre-set buttons and the ensemble label are  
displayed.  
<Searching by programme type and language>  
and <Languages to be displayed> in  
<Programme Type (PTY) Function>  
At the operation to press [DISP] button, use [AUTO]  
button instead.  
<Automatic Switching DAB priority>  
This function cannot be used.  
The marking of products using lasers  
(Except for some areas)  
CLASS 1  
LASER PRODUCT  
The label is attached to the chassis/case and says  
that the component uses laser beams that have  
been classified as Class 1. This means that the unit  
is utilizing laser beams that are of a weaker class.  
There is no danger of hazardous radiation outside  
the unit  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
5
About CDs  
Handling CDs  
• Do not touch the recording surface of the CD.  
Removing CDs  
When removing CDs from this unit, pull them out  
horizontally.  
CDs that cannot be used  
• CDs that are not round cannot be used.  
• CD-R and CD-RW are easier to damage than a  
normal music CD. Use a CD-R or a CD-RW after  
reading the caution items on the package etc.  
• Do not stick tape etc. on the CD, or use a CD with  
tape stuck on it.  
• CDs with coloring on the recording surface or CDs  
that are dirty cannot be used.  
• This unit can only play the CDs with  
When using a new CD  
If the CD center hole or outside rim has burrs,  
use the CD only after removing the burrs with a  
ballpoint pen, etc.  
.
This unit may not correctly play discs which do  
not have the mark.  
• You cannot play a CD-R or CD-RW that has not  
been finalized. (For the finalization process refer to  
your CD-R/CD-RW writing software, and your CD-  
R/CD-RW recorder instruction manual.)  
Burrs  
Burrs  
CD storage  
• Do not place CDs in direct sunlight (On the seat  
or dashboard etc.) or where the temperature is  
high.  
• Store CDs in their cases.  
CD accessories  
Do not use disc type accessories.  
CD cleaning  
Clean from the center of the disc and move  
outward.  
|
6
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About USB device  
Notes on Use of the USB device  
This unit can play audio files stored in the flash  
memory and digital audio player that have a USB  
port (these devices are referred to as USB devices in  
this document).  
The following restrictions are placed on the types  
and usage of available USB devices:  
Install the USB device in the place where it will not  
prevent you from driving your vehicle properly.  
Do not leave the USB device in the vehicle for a long  
time. It can deform or damage due to direct sunlight,  
high temperature, etc.  
Take backups of the audio files used with this unit.  
The files can be erased depending on the operating  
conditions of the USB device.  
Available USB devices  
• USB devices belonging to the USB mass storage  
class.  
We shall have no compensation for any damage arising  
out of erasure of the stored data.  
Leave the cap on when not using an USB device.  
• USB devices whose maximum current  
consumption is 500 mA or less.  
For the supported formats and USB device types,  
About USB device Operation  
• USB device operation is the same as audio  
file operation unless otherwise some notice is  
indicated.  
• USB source is recognized as CD source on the  
connected unit.  
USB Mass Storage Class:  
USB devices that the PC can recognize as an external  
storage without using any special driver or application  
software.  
Contact the sales agent as to whether your USB device  
conforms to the USB mass storage class specs.  
Using an unsupported USB device can result in abnormal  
playback or display of the audio file.  
Even if you use the USB device conforming to the above  
specs, audio files cannot be played normally depending  
on the type or condition of the USB device.  
About the Connection of the USB device  
• Do not directly connect the USB device to the  
USB connector on the panel. Connect it using a  
cable.  
• When connecting the USB drive, usage of the  
supplied USB cable is recommended.  
Normal playback is not guaranteed when a cable  
other than the USB compatible cable is used.  
Connecting a cable whose total length is longer  
than 5 m can result in abnormal playback.  
You cannot connect a USB device via a USB hub.  
English  
|
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
About AAC, MP3 and WMA  
The playable AAC/MP3/WMA file (hereafter called  
Audio file) and the media format has the following  
limitation. The Audio file, which is not conforming  
to the specification, may not play normally, or the  
file and folder names may not display correctly.  
Playable CD-R/RW format  
• ISO 9660 Level 1/2  
• Joliet  
• Romeo  
• Long file name.  
Playable Audio file  
Playable file format of USB device  
• For the formats supported by USB devices, refer to  
AAC, MP3, WMA  
Attach the correct extension for the Audio file (AAC:  
".M4A", MP3: ".MP3", WMA: ".WMA")  
Do not attach the extensions to files other than the  
Audio file. If the extension is attached, the file, which is  
not the Audio file, will play and outputs a loud noise,  
causing damage to the speaker.  
The files with copy protection cannot be played.  
Audio files cannot be played depending on the encoding  
software setting, USB device type, and/or recording  
conditions.  
The unit may not be compatible with upgrade  
of compression format standard and additional  
specifications.  
The maximum number of characters for  
display (CD-R/RW)  
File/Folder name: 128 characters  
MP3 ID3 Tag/ WMA Contents property:  
30 characters  
AAC song information: 60 characters  
File/Folder name is the number of the characters  
including the extensions.  
This unit can display the following versions of MP3 ID3  
tag: version 1.0/ 1.1/ 2.3  
For details on the formats used for USB devices and  
restrictions, refer to http://www.kenwood.com/usb/.  
AAC ID3 Tag cannot be displayed.  
Limitation of structure for the file and the  
folder (CD-R/RW)  
• Maximum number of directory levels: 8  
• Maximum number of folders: 100  
Playable AAC file  
".m4a" file encoded by AAC-LC format.  
for the details.  
• Maximum number of files per folder: 4096  
Playable MP3 file  
• MPEG 1/2 Audio Layer 3 file  
• Transfer bit rate: 8-320 kbps  
• Sampling frequency: 16, 22.05, 24, 32, 44.1, 48 kHz  
About partition of the USB device  
• While using the USB device, virtual folders are  
created to control the partition in the USB device.  
These folders appear in the first level (root)  
directory as "#:". "#" is an alphabet to identify each  
partition.  
• Even when the USB device does not have  
partition, "A:" folder is created, and audio files are  
controlled inside this folder.  
Playable WMA file  
• The file in accordance with Windows Media Audio  
(Except for the file for Windows Media Player 9 or  
after which applies the new functions)  
• Transfer bit rate: 48-192 kbps  
• Sampling frequency: 32, 44.1, 48 kHz  
Playable Storage media  
• CD-ROM, CD-R, CD-RW  
• USB device  
CD-RW discs which are quick formatted by the writing  
software cannot be used.  
When recording to the maximum CD-R/RW media  
capacity at once, the writing software is set to "Disc at  
once".  
For details on the available USB devices, refer to <About  
USB device> (page 7).  
|
8
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playing order of the Audio file  
• The Audio file plays in the order which is written  
by CD writing software. You may be able to set  
the playing order by writing the play sequence  
numbers such as "01" to "99" at the beginning of  
the file name.  
• Audio files are played in the order the files are  
written. You can specify the order of playback by  
numbering files in a folder and writing them by  
folder. (USB device)  
Example  
^
¡
:
Folder  
F
CD  
(1)  
: A
Audio file  
¡!  
2
3
¡"  
¡#  
4
¡$  
5
¡%  
¡P  
• Playing order  
Playing order after ¡! play.  
¡", ¡#, ¡$, ¡%...  
• File search  
Forward file search during ¡" play.  
Push the Control knob towards [¢] ¡#  
• Folder search  
Forward folder search during ¡" play.  
Push the Control knob towards [FM] 4, 5...  
• File select  
When the selection is set to file ¡%.  
Push the Control knob towards [¢]  
¡%...P, %...  
• Folder select 1  
When the selection is set to directory 4, and you  
want to skip to the folder 2 at the same level.  
Push the Control knob towards [4] 2  
When the selection is set to directory 3, moves  
the level up by folder select.  
Push the Control knob towards [AM] 2  
• Folder select 2  
When the selection is set to directory 1, and you  
want to skip to the folder 4.  
Push the Control knob towards [¢] 3, 4...  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
9
General features  
DISP  
VOL  
ATT  
Control knob  
Q
SRC  
Clock display  
LOUD indicator  
ATT indicator  
Power  
*1 You can operate this function when <Built-in  
Auxiliary input Setting> (page 29) is set to "AUX ON".  
Turning ON the Power  
Press the [SRC] button.  
Turning OFF the Power  
Press the [SRC] button for at least 1 second.  
Volume  
Selecting the Source  
Increasing Volume  
Turn the [VOL] knob clockwise.  
Press the [SRC] button.  
Decreasing Volume  
Turn the [VOL] knob counterclockwise.  
Source required  
Tuner  
USB device  
Display  
"TUNER"  
"USB"  
CD  
"CD"  
TV (Optional accessory)  
External disc (Optional accessory)  
Auxiliary input *1  
"TV"  
"CD CH"  
"AUX"  
Attenuator  
Turning the volume down quickly.  
Press the [ATT] button.  
Each time you press the button, the Attenuator  
turns ON and OFF.  
Auxiliary input (Optional accessory)  
Standby (Illumination only mode)  
"AUX EXT"  
"STANDBY"  
When the Attenuator is ON, the "ATT" indicator  
blinks.  
|
10  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Q  
4 Adjust the Basic Audio item  
Turn the [VOL] knob.  
Selecting the best sound setting preset for  
different types of music.  
Adjustment Item Display  
Rear Volume *1  
"R-VOL"  
Subwoofer level*2,3 "SW L"  
Range  
0 — 35  
–15 — +15  
–8 — +8  
–8 — +8  
–8 — +8  
Left 15 — Right 15  
Rear 15 — Front 15  
1 Select the source to set  
Press the [SRC] button.  
Bass level*4  
Middle level*4  
Treble level*4  
Balance  
"BAS L"  
"MID L"  
"TRE L"  
"BAL"  
2 Select the Sound type  
Press the [Q] button.  
When you press the button once, the current  
sound setting is displayed.  
Each time you press the button, the sound  
setting alternates.  
Fader*3  
"FAD"  
Exit Audio Control mode (Volume control mode)  
Sound setting  
User memory  
Rock  
Pops  
Easy  
Top 40  
Jazz  
Natural  
Display  
"USER"  
"ROCK"  
"POPS"  
"EASY"  
"TOP 40"  
"JAZZ"  
*1 You can control this item when "2ZON" of <Audio  
Setup> (page 12) is set to "ON".  
*2 You can control this item when <Switching preout>  
(page 27) is set to "SWPRE SW".  
*2 You can control this item when <Subwoofer  
Output> (page 13) is set to "SW ON".  
*3 You can control this item when "2ZON" of <Audio  
Setup> (page 12) is set to "OFF".  
*4 You can adjust these items in detail. Refer to  
<Adjusting the detail of Audio Control>(Page12).  
*4 Source tone memory: Puts the set up value in the  
memory per source. (Detail Audio item is included)  
"NATURAL"  
User memory: The values set on the <Audio Control>  
(page 11).  
Change each setting value with the <Speaker  
Setting> (page 13).  
5 Exit Audio Control mode  
Press any button.  
Press a button other than the [VOL] knob and  
[ATT] button.  
First, select the speaker type with the Speaker setting.  
Audio Control  
1 Select the source to adjust  
Press the [SRC] button.  
2 Enter Audio Control mode  
Press the [VOL] knob.  
3 Select the Basic Audio item to adjust  
Press the [VOL] knob.  
Each time you press the knob, the item to be  
adjusted alternates between the items shown in  
the table below.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
11  
General features  
Adjusting the detail of Audio  
Control  
Audio Setup  
Setting the Sound system, such as Cross over  
Network.  
Among the Basic Audio items, you can adjust the  
Bass level, Middle level, and Treble level in detail.  
1 Select the source to adjust  
Press the [SRC] button.  
1 Select the Basic Audio item  
Select the desired item to be set in detail from  
followings;  
• Bass level  
• Middle level  
• Treble level  
For how to select Basic Audio items, see <Audio  
Control> (page 11).  
2 Enter Audio Setup mode  
Press the [VOL] knob for at least 1 second.  
3 Select the Audio Setup item to adjust  
Press the [VOL] knob.  
Each time you press the knob, the item to be  
adjusted alternates between the items shown in  
the table below.  
2 Enter Detail adjustment mode of Audio  
Control  
Press the [VOL] knob for at least 1 second.  
4 Setup the Audio item  
Turn the [VOL] knob.  
Adjustment Item Display  
Range  
Through/40/60/80/100/120/  
150/180/220 Hz  
3 Select the Detail Audio item to adjust  
Press the [VOL] knob.  
Each time you press the knob, the item to be  
adjusted alternates between the items shown in  
the table below.  
Front High Pass Filter*2 "HPF"  
Rear High Pass Filter*2 "HPR"  
Through/40/60/80/100/120/  
150/180/220 Hz  
Low Pass Filter*1,2  
"LPF"  
50/60/80/100/120/  
Through Hz  
Reverse (180°)/ Normal (0°)  
4 Adjust the Detail Audio item  
Turn the [VOL] knob.  
Subwoofer Phase*1,2,3 "PHAS"  
Volume offset  
Loudness  
Dual Zone System  
"V-OFF"  
"LOUD"  
"2ZON"  
–8 —  
OFF/ON  
OFF/ON  
0
Bass level  
Adjustment Item  
Bass Center Frequency "BAS F"  
Display  
Range  
40/50/60/70/80/100/  
120/150 Hz  
Bass Q Factor  
Bass Extend  
"BAS Q"  
"B EX"  
1.00/1.25/1.50/2.00  
OFF/ON  
Volume offset: Sets each source’s volume as a  
difference from the basic volume.  
Loudness: Compensates for low and high tones  
during low volume.  
*1 You can control this item when <Switching preout>  
(page 27) is set to "SWPRE SW".  
*1 You can control this item when <Subwoofer  
Output> (page 13) is set to "SW ON".  
*2 You can control this item when "2ZON" of <Audio  
Setup> (page 12) is set to "OFF".  
*3 You can control this item when Low Pass Filter is not  
set to Through.  
Middle level  
Adjustment Item  
Middle Center Frequency "MID F"  
Middle Q Factor  
Display  
Range  
0.5/1.0/1.5/2.0 kHz  
1.0/2.0  
"MID Q"  
Treble level  
Adjustment Item  
Treble Center Frequency "TRE"  
Display  
Range  
10.0/12.5/15.0/17.5 kHz  
Dual Zone System  
5 Exit the Detail Audio Control mode  
Press the [VOL] knob for at least 1 second.  
Main source and sub source (Auxiliary input) output  
Front channel and Rear channel separately.  
- Set up the channel of sub source by <Dual Zone  
System Setting> (page 28).  
- Select Main source by [SRC] button.  
- Adjust the volume of Front channel by [VOL] knob.  
- Adjust the volume of Rear channel by <Audio  
Control> (page 11).  
When you set the Bass Extend to ON, low frequency  
response is extended by 20%.  
You can exit the Audio Control mode at anytime  
by pressing any button except for [VOL] and [ATT]  
buttons.  
- The Audio Control has no effect on sub source.  
|
12  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
You can use the Dual Zone System with the internal  
auxiliary input.  
TEL Mute  
The audio system automatically mutes when a  
call comes in.  
5 Exit Audio Setup mode  
Press the [VOL] knob for at least 1 second.  
When a call comes in  
"CALL" is displayed.  
The audio system pauses.  
Listening to the audio during a call  
Press the [SRC] button.  
Speaker Setting  
The "CALL" display disappears and the audio  
system comes back ON.  
Fine-tuning so that the System Q value is optimal  
when setting the speaker type.  
When the call ends  
Hang up the phone.  
The "CALL" display disappears and the audio  
system comes back ON.  
1 Enter Standby  
Press the [SRC] button.  
Select the "STANDBY" display.  
2 Enter Speaker Setting mode  
Press the [VOL] knob.  
To use the TEL Mute feature, you need to hook up  
the MUTE wire to your telephone using a commercial  
telephone accessory. Refer to <Connecting Wires to  
Terminals> (page 35).  
3 Select the Speaker type  
Turn the [VOL] knob.  
Each time you turn the knob, the setting  
alternates between the settings shown in the  
table below.  
Speaker type  
OFF  
For 5 & 4 in. speaker  
For 6 & 6x9 in. speaker  
For the OEM speaker  
Display  
"SP OFF"  
"SP 5/4"  
"SP 6*9/6"  
"SP OEM"  
4 Exit Speaker Setting mode  
Press the [VOL] knob.  
Subwoofer Output  
Turning the Subwoofer output ON or OFF.  
Push the Control knob toward [AM] for at  
least 2 seconds.  
Each time you push the knob, Subwoofer output  
switches ON and OFF.  
When it is ON, "SW ON" is displayed.  
You can control this function when <Switching  
preout> (page 27) is set to "SWPRE SW".  
You can control this function when "2ZON" of <Audio  
Setup> (page 12) is set to "OFF".  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
13  
General features  
Switching Display  
Changing the information displayed.  
Press the [DISP] button.  
Each time the button is pressed, the display  
switches as shown below.  
In Tuner source  
Information  
Frequency  
Clock  
Display  
"FREQ"  
"CLOCK"  
In CD & External disc source  
Information  
Disc title  
Track title  
Track number & Play time  
Clock  
Display  
"D-TITLE"*  
"T-TITLE"*  
"P-TIME"  
"CLOCK"  
In Audio file source  
Information  
Display  
"TITLE"*  
"ALBUM"*  
"FOLDER"  
"FILE"  
Song title & Artist name  
Album name & Artist name  
Folder name  
File name  
Track number & Play time  
Clock  
"P-TIME"  
"CLOCK"  
In Standby/ Auxiliary input source  
Information  
Source name  
Clock  
Display  
"SRC NAME"  
"CLOCK"  
* If the contents of the information cannot be  
displayed, Play time is displayed.  
When LX-AMP is connected, the item setup by the  
Display mode of LX-AMP is displayed.  
Track number at Audio file displays the last 3 digits  
when it exceeds 1000 songs.  
When you select the clock display, the display setting  
of each source will be changed to the clock display.  
|
14  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tuner/TV control features  
Control knob  
SRC  
AUTO/AME  
1 - 6  
Band display  
Frequency display  
Preset station  
ST indicator  
number  
Tuning  
Tuning Mode  
Selecting the station.  
Choose the tuning mode.  
Press the [AUTO] button.  
1 Select tuner source  
Press the [SRC] button.  
Select the "TUNER" display.  
Each time you press the button, the Tuning  
mode alternates between the modes shown in  
the table below.  
2 Select the band  
Tuning mode  
Auto seek  
Preset station seek "AUTO 2"  
Display  
"AUTO 1"  
Operation  
Automatic search for a station.  
Search in order of the stations  
in the Preset memory.  
Push the Control knob towards [FM] or [AM].  
Each time you push the knob toward [FM], it  
switches between the FM1, FM2, and FM3 bands.  
Manual  
"MANUAL" Normal manual tuning control.  
3 Tune up or down band  
Push the Control knob towards [4] or  
[¢].  
During reception of stereo stations the "ST" indicator  
is ON.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
15  
Tuner/TV control features  
Function of remote control  
Auto Memory Entry  
Direct Access Tuning  
Putting stations with good reception in the  
memory automatically.  
Entering the frequency and tuning.  
1 Select the band for Auto Memory Entry  
Push the Control knob towards [FM] or [AM].  
1 Select the band  
Press the [FM] or [AM] button.  
2 Open Auto Memory Entry  
Press the [AME] button for at least 2 seconds.  
"A-MEMORY" is displayed.  
2 Enter Direct Access Tuning mode  
Press the [DIRECT] button on the remote  
control.  
When 6 stations that can be received are put in  
the memory, Auto Memory Entry closes.  
"– – – –" is displayed.  
3 Enter the frequency  
Press the number buttons on the remote  
control.  
Example:  
Desired frequency  
92.1 MHz (FM)  
810 kHz (AM)  
Press button  
[0], [9], [2], [1]  
[0], [8], [1], [0]  
Preset Tuning  
Recalling the stations in the memory.  
1 Select the band  
Cancelling Direct Access Tuning  
Press the [DIRECT] button on the remote  
control.  
Push the Control knob towards [FM] or [AM].  
2 Recall the station  
Press the desired [1] — [6] button.  
Station Preset Memory  
Frequency Step Setting  
Putting a station in the memory.  
Changing the tuning frequency step.  
The original setting is FM band 50 kHz, and AM  
band 9 kHz.  
1 Select the band  
Push the Control knob towards [FM] or [AM].  
2 Select the frequency to put in the memory  
Push the Control knob towards [4] or  
[¢].  
1 Turn the power OFF  
Press the [SRC] button for at least 1 second.  
2 Switch the frequency step  
While pressing the [1] and [5] buttons, press  
the [SRC] button.  
Release the [SRC] button first, after the display  
appears, release your fingers from the [1] and [5]  
buttons.  
3 Put the frequency in the memory  
Press the desired [1] — [6] button for at least  
2 seconds.  
The preset number display blinks 1 time.  
On each band, 1 station can be put in the  
memory on each [1] — [6] button.  
The frequency step changes to FM band 200 kHz,  
and AM band 10 kHz.  
When the same operation is repeated, the frequency  
step returns to the original setting.  
When the frequency step is changed, the frequencies  
in the memory are deleted.  
|
16  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function of LX BUS Television  
Function of remote control  
TV Tuning  
Direct TV Tuning  
Selecting the TV channel of a connected LX BUS  
Television (optional accessory).  
The action depends on the setting of the  
connected LX BUS Television. Refer to the user  
instruction of the LX BUS Television for details.  
Entering the TV channel and tuning.  
1 Select the TV band  
Press the [FM] button.  
2 Enter Direct TV Tuning mode  
Press the [DIRECT] button on the remote  
control.  
1 Select TV source  
Press the [SRC] button.  
Select the "TV" display.  
"– –" is displayed.  
3 Enter the TV channel  
2 Select the TV band and Video input  
Push the Control knob toward [FM].  
Each time you push the knob to [FM], TV bands  
and Video input alternate.  
Press the number buttons on the remote  
control.  
Example:  
Desired channel  
Press button  
3 Select the TV channel  
Push the Control knob towards [4] or  
[¢].  
8 ch  
[0], [8]  
Cancelling Direct TV Tuning  
Press the [DIRECT] button on the remote  
control.  
Function of LX BUS Television  
TV channel Preset Memory  
Putting the TV channels in the memory.  
1 Select the TV band  
Push the Control knob toward [FM].  
2 Select the TV channel to put in the memory  
Push the Control knob towards [4] or  
[¢].  
3 Put the TV channel in the memory  
Press the desired [1] — [6] button for at least  
2 seconds.  
The preset number display blinks 1 time.  
On each band, 1 TV channel can be put in the  
memory on each [1] — [6] button.  
Function of LX BUS Television  
Preset TV Tuning  
Recalling the TV channels in the memory.  
1 Select the TV band  
Push the Control knob toward [FM].  
2 Recall the TV channel  
Press the desired [1] [6] button.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
17  
CD/USB device/Audio file/External disc control features  
Control knob  
SRC  
S.MODE SCAN RDM/ REP F.SEL M.RDM  
A.RDM/3  
Track number  
Play time  
Disc number  
IN indicator  
Play mode  
Playing CD & Audio file  
Playing USB device  
When a disc is inserted  
Press the [SRC] button.  
Select the "CD" display.  
Playing USB device  
1 Select a source other than the USB device  
Press the [SRC] button.  
2 Connect the USB device.  
When a disc is inserted, the "IN" indicator is ON.  
3 Select USB source  
Press the [SRC] button.  
Select the "USB" display.  
Pause and play  
Press the Control knob.  
Each time you press the knob, the audio pauses  
or plays.  
For the types of available USB devices and how to  
connect USB devices, refer to <About USB device>  
(page 7).  
After you stopped playing a file contained in the USB  
device, you can restart playing the file from the point  
where you stopped its playback.  
Eject the disc  
Press the [0] button.  
You can cancel the announcement when selecting  
the folder by <Voice Index> (page 30) during the play  
of the ACDrive media.  
Even after removing the USB device, you can restart  
playing the file from the point where you stopped  
its playback as long as the files contained in the USB  
device are all the same.  
Be sure to insert the USB device connector as far as it  
will go.  
You can play the disc (ACDrive media) made by Media  
Manager by the same operation.  
|
18  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
You can cancel the announcement when selecting  
the folder by <Voice Index> (page 30) during the play  
of the ACDrive media.  
Fast Forwarding and Reversing  
Fast Forwarding  
Hold down toward [¢] with the Control  
knob.  
Release to resume the playback.  
Pause and play  
Press the Control knob.  
Each time you press the knob, the audio pauses  
or plays.  
Reversing  
Hold down toward [4] with the Control  
knob.  
Release to resume the playback.  
Removing the USB device  
1 Select a source other than the USB device  
Press the [SRC] button.  
2 Remove the USB device.  
There is no sound while the Audio file is being  
searched.  
You cannot fast Forwarding and Reversing depending  
on AAC file format.  
Removing the USB device with it selected as a source  
can damage the data stored in the USB device.  
You can remove the USB device safely with the unit  
power turned off.  
Track/File Search  
Playing External Disc  
Searching for a song on the disc or in the Audio  
file folder.  
Playing discs set in the optional accessory disc  
player connected to this unit.  
Push the Control knob towards [4] or  
[¢].  
Press the [SRC] button.  
Select the display for the disc player you want.  
Display examples:  
Function of disc changer/ Audio file  
Display  
"CD CH"  
"MD CH"  
Disc player  
CD changer  
MD changer  
Disc Search/Folder Search  
Selecting the disc set in the Disc changer or the  
folder recorded on the Audio file media.  
Pause and play  
Push the Control knob towards [FM] or [AM].  
Press the Control knob.  
Each time you press the knob, the audio pauses  
or plays.  
Disc 10 is displayed as "0".  
The functions that can be used and the information  
that can be displayed will differ depending on the  
external disc players being connected.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
19  
CD/USB device/Audio file/External disc control features  
Function of remote control  
Track/File/Disc/Folder Repeat  
Direct Track/File Search  
Replaying the song, disc in the Disc changer or  
Audio file folder you are listening to.  
Doing Track/File Search by entering the track/file  
number.  
Press the [REP] button.  
Each time you press the button, the Repeat Play  
alternates between the modes shown in the  
tables below.  
1 Enter the track/file number  
Press the number buttons on the remote  
control.  
In CD & External disc source  
Repeat play  
Track Repeat  
Disc Repeat (In Disc Changer)  
OFF  
Display  
You can select Direct File Search up to 999.  
"TRAC REP"  
"DISC REP"  
"REP OFF"  
2 Do Track/File Search  
Press the [4] or [¢] button.  
Cancelling Direct Track/File Search  
Press the [38] button.  
In Audio file source  
Repeat play  
File Repeat  
Folder Repeat  
OFF  
Display  
"FILE REP"  
"FOLD REP"  
"REP OFF"  
Function of disc changers with remote control  
Direct Disc Search  
Doing Disc Search by entering the disc number.  
Scan Play  
1 Enter the disc number  
Press the number buttons on the remote  
control.  
Playing the first part of each song on the disc  
or Audio file folder you are listening to and  
searching for the song you want to hear.  
2 Do Disc Search  
Press the [+] or [] button.  
1 Start Scan Play  
Press the [SCAN] button.  
"TRAC SCN"/ "FILE SCN"/ "SCAN ON" is displayed.  
Cancelling Direct Disc Search  
Press the [38] button.  
2 Release it when the song you want to listen  
to is played  
Input "0" to select disc 10.  
Press the [SCAN] button.  
Random Play  
Play all the songs on the disc or Audio file folder  
in random order.  
Press the [RDM] button.  
Each time you press the button, Random Play  
turns ON or OFF.  
When the Random mode is ON, "DISC RDM"/  
"FOLD RDM"/ "RDM ON" is displayed.  
When you push the Control knob toward [¢], the  
next random song starts.  
|
20  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function of disc changer  
Function of Audio file  
Magazine Random Play  
Select mode  
Play the songs on all the discs in the disc changer  
in random order.  
Quickly selecting the file or folder you want to  
hear.  
Press the [M.RDM] button.  
Each time you press the button, the Magazine  
Random Play turns ON or OFF.  
When the Magazine Random mode is ON,  
"MGZN RDM" is displayed.  
1 Select the Select mode  
Press the [F.SEL] button.  
Display  
"FILE SEL"*1  
Select mode  
Refer to <File Select mode> (page 22).  
"FLD SEL1"/ "FLD SEL" Refer to <Folder Select 1 mode> (page 22).  
"FLD SEL2" *2  
Refer to <Folder Select 2 mode> (page 23).  
When you push the Control knob toward [¢], the  
next random song starts.  
Exit the Select mode  
The Select mode does not function when <All  
Random Play> (page 21) is ON.  
*1 You cannot operate this function when <Random  
Play> (page 20) is set to "ON".  
*2 You cannot operate this function when <Switching  
the Play mode> (page 23) is set to other than  
"FOLDER" while playing ACDrive media.  
Function of Audio file  
All Random Play  
Playing randomly from all of the Audio files  
recorded in the media.  
Press the [A.RDM] button for at least 1  
second.  
When the random mode is ON, "ALL RDM" is  
displayed.  
2 Select the file/ folder  
Refer to the explanation of the procedure  
performed in each select mode.  
Scrolling the file/ folder name display  
Push the Control knob toward [FM] for at  
least 2 seconds.  
Cancelling the All Random Play  
Press the [A.RDM] button.  
When you push the Control knob toward [¢], the  
next random song starts.  
You can cancel the announcement when selecting  
the folder by <Voice Index> (page 30) during the play  
of the ACDrive media.  
In the File Select mode, the <Voice Index> (page 30)  
announcement is not made.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
21  
CD/USB device/Audio file/External disc control features  
Function of Audio file  
Function of Audio file  
File Select mode  
Folder Select 1 mode  
You can select an audio file in the folder currently  
being played by file name.  
Select the target folder by tracing the hierarchical  
levels of folders. This is convenient when  
managing audio files by folder.  
1 Enter File Select mode  
Press the [F.SEL] button.  
Select the "FILE SEL" display.  
Refer to <Select mode> (page 21).  
File name display  
1 Enter Folder Select 1 mode  
Press the [F.SEL] button.  
Select the "FLD SEL1"/ "FLD SEL" display.  
Refer to <Select mode> (page 21).  
Folder name display  
Displays the current file name.  
Displays the current folder name.  
2 Select the file  
Push the Control knob towards [4] or  
[¢].  
2 Select the folder level*  
Push the Control knob towards [FM] or [AM].  
With the [FM] button, you move 1 level down  
and with the [AM] button, 1 level up.  
Switching between files in units of 10 songs  
Push the Control knob towards [FM] or [AM].  
With the [FM] button, you move 10 songs up and  
with the [AM] button, 10 songs down.  
Selecting a folder in the same level  
Push the Control knob towards [4] or  
[¢].  
With the [4] of the Control knob, you move  
to the previous folder, and with the [¢] of the  
Control knob, to the next folder.  
You can select File Select mode up to 999.  
3 Decide the file to play  
Press the Control knob.  
The File Select mode releases, and the Audio file  
being displayed plays.  
Returning to the top level*  
Press the [3] button.  
* You cannot operate this function when <Switching  
the Play mode> (page 23) is set to other than  
"FOLDER" while playing ACDrive media.  
3 Decide the folder to play  
Press the Control knob.  
The Folder Select mode releases, and the Audio  
file in the folder being displayed plays.  
|
22  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Function of Audio file  
Function of ACDrive media  
Folder Select 2 mode  
Switching the Play mode  
Select the target folder within the folders  
containing audio files. The folder which contains  
playable audio files is only displayed.  
Arrange the playing orders of the songs by  
categories.  
Press the [S.MODE] button.  
Each time you press the button, the Play mode  
alternates between the modes shown in the  
table below.  
1 Enter Folder Select 2 mode  
Press the [F.SEL] button.  
Select the "FLD SEL2" display.  
Refer to <Select mode> (page 21).  
Folder name display  
The Play mode indicator is ON.  
Play mode  
"PLAYLIST"  
"GENRE"  
Category which is to be arranged  
Play list order.  
By genre.  
Displays the current folder name.  
"ARTIST"  
By artist.  
"ALBUM"  
"FOLDER"  
By album.  
By the folder recorded in media  
The category information of each song is the data  
registered in Media Manager when ACDrive media is  
being generated.  
You can cancel the announcement made when the  
mode is changed by <Voice Index> (page 30).  
You can select the advancement of the Play mode  
information by [AM] and [FM] knob.  
2 Select the folder  
Push the Control knob towards [4] or  
[¢].  
Each time you push the knob, the folders  
containing audio files are displayed one after  
another.  
Check the name of upper level folder  
Push the Control knob towards [FM] or [AM].  
With the [FM] button, the folder name in the  
upper level is displayed.  
With the [AM] button, the folder name in the  
lower level is displayed.  
"
" is displayed while the upper level folder is  
displayed.  
3 Decide the folder to play  
Press the Control knob.  
The Folder Select mode releases, and the Audio  
file in the folder being displayed plays.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
23  
CD/USB device/Audio file/External disc control features  
Function of ACDrive media  
Text/Title Scroll  
Letter Seek  
Scrolling the displayed CD text, Audio file text, or  
MD title.  
Push the Control knob toward [FM] for at  
least 2 seconds.  
You can search for the song, you want to play, by  
selecting the initial of Genre name, Artist name,  
or Album name.  
1 Enter the Letter Seek mode  
Press the [S.MODE] button for at least 1  
second.  
When the <Display Illumination Control> (page 27) is  
set to OFF, the display may black out while scrolling.  
This operation does not function when <All Random  
Play> (page 21) is ON.  
This function is available only when the Play mode is  
set Genre, Artist, or Album.  
Cancelling the Letter Seek  
Press the [S.MODE] button.  
2 Start the Letter Seek  
Push the Control knob towards [4] or  
[¢].  
The initial of Genre name, Artist name, or Album  
name is displayed and announced in order.  
The announcement of the initial can be canceled by  
<Voice Index> (page 30).  
When you push the Control knob to the reverse [4]  
or [¢] during Letter Seek, the initial is displayed and  
announced in the reversed order.  
Once Letter Seek starts, it cannot be cancelled.  
3 Select the song to play  
Press the Control knob when the initial of  
the song you are searching is displayed and  
announced.  
The selected initial group plays.  
|
24  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu system  
Control knob  
MENU  
SRC  
Menu display  
Example: When you select "BEEP", each time you  
push the knob it alternates between  
"BEEP ON" or "BEEP OFF". Select 1 of  
them as the setting.  
You can continue by returning to step 2 and  
setting other items.  
Menu System  
Setting beep sound during operation, etc.  
functions.  
The Menu system basic operation method is  
explained here. The reference for the Menu items  
and their setting content is after this operation  
explanation.  
4 Exit Menu mode  
Press the [MENU] button.  
1 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
When other items those applicable to the basic  
operation method above are displayed, their setting  
content chart is entered. (Normally the setting listed at  
the top of the chart is the original setting.)  
Also, the explanation for items that are not applicable  
(<Manual Clock Adjustment> etc.) are entered step  
by step.  
2 Select the menu item  
Push the Control knob towards [FM] or [AM].  
Example: When you want to set the beep sound  
select the "BEEP" display.  
3 Set the menu item  
Push the Control knob towards [4] or  
[¢].  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
25  
Menu system  
In Standby mode  
Activating Security Code  
If you enter the wrong code in steps 4 through 6,  
repeat from step 4.  
Activating the Security Code disables the usage  
of audio unit by someone else. Once the Security  
Code is activated, the entry of authorized Security  
Code is required to turn on the audio unit when  
it is removed from the vehicle. Indication of this  
Security Code activation prevents your precious  
audio unit from stealing.  
Resetting the Security Code function when  
the audio unit is first used after removed  
from the battery power source or the Reset  
button is pressed  
1 Turn the power ON.  
2 Do the step 4 through 7 operation, and enter  
the Security Code.  
"APPROVED" is displayed.  
You can set the Security Code with a 4 digit number of  
your choice.  
The Security Code cannot be displayed or referenced.  
Make a note of the Security Code and treasure it up.  
Now, you can use the unit.  
1 Enter Standby  
When the Security Code function is activated, "CODE  
SET" changes to "CODE CLR".  
To deactivate the Security Code function, see the next  
section <Deactivating Security Code>.  
Press the [SRC] button.  
Select the "STANDBY" display.  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
When "MENU" is displayed, "CODE SET" is also  
displayed.  
In Standby mode  
3 Enter Security Code mode  
Press the Control knob for at least 1 second.  
When "ENTER" is displayed, "CODE" is also  
displayed.  
Deactivating Security Code  
To deactivate the Security Code function.  
1 Select Security Code mode  
Push the Control knob towards [FM] or [AM].  
Select the "CODE CLR" display.  
4 Select the digits to enter  
Push the Control knob towards [4] or  
[¢].  
2 Enter Security Code mode  
Press the Control knob for at least 1 second.  
When "ENTER" is displayed, "CODE" is also  
displayed.  
5 Select the Security Code numbers  
Push the Control knob towards [FM] or [AM].  
6 Repeat steps 4 and 5, and complete the  
Security Code.  
3 Select the digits to enter  
Push the Control knob towards [4] or  
[¢].  
4 Select the Security Code numbers  
Push the Control knob towards [FM] or [AM].  
7 Confirm the Security Code  
Press the Control knob for at least 3 seconds.  
When "RE-ENTER" is displayed, "CODE" is also  
displayed.  
5 Repeat steps 3 and 4, and complete the  
Security Code.  
8 Do the step 4 through 7 operation, and  
reenter the Security Code.  
"APPROVED" is displayed.  
The Security Code function activates.  
6 Press the Control knob for at least 3 seconds.  
"CLEAR" is displayed.  
The Security Code function deactivates.  
9 Exit Security Code mode  
Press the [MENU] button.  
7 Exit Security Code mode  
Press the [MENU] button.  
|
26  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Display Illumination Control  
This function turns off the display when you  
perform no operation for 5 seconds. This function  
is effective when you are driving at night.  
If a wrong security code is entered, "ERROR" is  
displayed. Enter a correct security code.  
Display  
Setting  
"DISP ON"  
Keeps the display on.  
In Standby mode  
Turns off the display when you perform no  
operation for 5 seconds.  
"DISP OFF"  
Touch Sensor Tone  
Setting the operation check sound (beep sound)  
ON/OFF.  
When the display is off, pressing any key will turn on  
the display.  
When the display is off, you cannot perform any  
operation except for the following:  
Display  
Setting  
"BEEP ON"  
"BEEP OFF"  
Beep is heard.  
Beep canceled.  
Volume  
Attenuator  
Selecting the source  
Ejecting the disc  
Turning off the power  
In Standby mode  
Manual Clock Adjustment  
During function control, such as the Menu System, the  
display stays on.  
1 Select Clock Adjustment mode  
Push the Control knob towards [FM] or [AM].  
Select the "CLK ADJ" display.  
2 Enter Clock Adjust mode  
Press the Control knob for at least 1 second.  
The clock display blinks.  
In Standby mode  
Dimmer  
Dimming this unit’s display automatically when  
the vehicle light switch is turned ON.  
3 Adjust the hours  
Push the Control knob towards [FM] or [AM].  
Display  
"DIM ON"  
"DIM OFF"  
Setting  
The display dims.  
The display doesn’t dim.  
Adjust the minutes  
Push the Control knob towards [4] or  
[¢].  
4 Exit Clock adjustment mode  
Press the [MENU] button.  
In Standby mode  
Switching preout  
Alternating the preout between the rear and  
subwoofer. (With the subwoofer the sound  
outputs without being effected by fader control.)  
In Standby mode  
Indirect Lighting  
You can illuminate the area around the display  
with soft indirect lighting.  
Display  
"SWPRE R"  
"SWPRE SW"  
Setting  
Rear preout.  
Subwoofer preout.  
Display  
Setting  
"LGHT ON"  
"LGHT OFF"  
Turns indirect lighting on.  
Turns indirect lighting off.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
27  
Menu system  
In Standby mode  
Other than Standby mode  
Built-in Amp Setting  
B.M.S. Frequency Offset  
Controlling the built-in amplifier.  
Turning OFF this control enhances the preout  
quality.  
Setting the central frequency, boosted by B.M.S.  
Display  
Setting  
"BMSF NML"  
"BMSF LOW"  
Boost with the normal central frequency.  
Drop the normal central frequency 20%.  
Display  
Setting  
"AMP ON"  
"AMP OFF"  
The built-in amplifier activates.  
The built-in amplifier deactivates.  
When LX AMP unit connecting  
AMP Control  
Other than Standby mode/  
You can control the LX AMP connected to the  
unit.  
When the Dual Zone System is ON  
Dual Zone System Setting  
1 Select AMP Control mode  
Setting the Front channel and Rear channel  
sound in the Dual Zone System.  
Push the Control knob towards [FM] or [AM].  
Select the "AMP CTRL" display.  
Display  
Setting  
2 Enter AMP Control mode  
Press the Control knob for at least 1 second.  
"ZONE2 R"  
Sub source (Auxiliary input source) is to be rear  
channel.  
"ZONE2 F"  
Sub source (Auxiliary input source) is to be front  
channel.  
3 Select the AMP Control item for adjustment  
Push the Control knob towards [FM] or [AM].  
For the details on the AMP Control item, see the  
Instruction manual attached to the LX AMP.  
Other than Standby mode  
4 Adjust the AMP Control item  
Push the Control knob towards [4] or  
[¢].  
B.M.S. (Bass Management System)  
Adjust the bass boost level of the external  
amplifier using the main unit.  
5 Exit AMP Control mode  
Display  
Setting  
Bass boost level is flat.  
Bass boost level is low (+6dB).  
Bass boost level is mid (+12dB).  
Bass boost level is high (+18dB).  
Press the [MENU] button.  
"BMS FLT"  
"BMS +6"  
"BMS +12"  
"BMS +18"  
You cannot use the LX AMP operation during standby  
mode.  
Refer to the catalog or instruction manual for power  
In FM reception  
amplifiers that can be controlled from this unit.  
For amplifiers, there are the models you can set from  
Flat to +18 dB, and the models you can set from Flat  
to +12 dB.  
When an amplifier that can only be set to +12 is  
connected to the unit, "BMS +18" will not work  
correctly even if it is selected.  
CRSC (Clean Reception System  
Circuit)  
Temporarily have reception alternate from  
stereo to mono to reduce multi-path noise when  
listening to the FM station.  
Display  
Setting  
"CRSC ON"  
"CRSC OFF"  
The CRSC is ON.  
The CRSC is OFF.  
|
28  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Text Scroll  
Setting the displayed text scroll.  
Strong electrical fields (such as from power lines) may  
cause unstable sound quality when CRSC is turned  
ON. In such a situation, turn it OFF.  
Display  
Setting  
"SCL AUTO"  
"SCL MANU"  
Repeats scroll.  
Scrolls when the display changes.  
Auxiliary Input Display Setting  
The text scrolled is listed below.  
- CD text  
- Folder name/ File name/ Song title/ Artist name/  
Selecting the display when changing to Auxiliary  
input source.  
Album name  
- MD title  
1 Select Auxiliary input source  
Press the [SRC] button.  
Select the "AUX"/ "AUX EXT" display.  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
In Standby mode  
Built-in Auxiliary input Setting  
3 Select Auxiliary input display setting mode  
Push the Control knob towards [FM] or [AM].  
Select the "NAME SET" display.  
Set the Built-in Auxiliary Input function.  
Display  
"AUX OFF" When selecting the source there’s no Auxiliary Input.  
"AUX ON" When selecting the source there’s Auxiliary Input.  
Setting  
4 Enter Auxiliary input display setting mode  
Press the Control knob for at least 1 second.  
The presently selected Auxiliary input display is  
displayed.  
In Standby mode  
5 Select the Auxiliary input display  
Push the Control knob towards [4] or  
CD Read Setting  
[¢].  
When there is a problem with playing a CD with  
special format, this setting plays the CD by force.  
Each time you push the knob, the display  
alternates as listed below.  
• "AUX"/ "AUX EXT"  
• "DVD"  
• "PORTABLE"  
• "GAME"  
Display  
"CD READ 1"  
"CD READ 2"  
Setting  
Play CD and Audio file.  
Play CD by force.  
• "VIDEO"  
• "TV"  
Setting "CD READ 2" cannot play Audio file.  
Some music CDs may not play even in the "CD READ  
2" mode.  
6 Exit Menu mode  
Press the [MENU] button.  
When operation stops for 10 seconds, the name at  
that time is registered, and the Auxiliary input display  
setting mode closes.  
The Auxiliary Input Display can be set only when the  
built-in auxiliary input or the auxiliary input of optional  
KCA-S210A is used.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
29  
Menu system  
Function of ACDrive media  
Other than Standby mode  
Voice Index  
Audio Preset Memory  
Setting the announcement during the play of  
ACDrive media.  
Registering the value setup by Sound Control. The  
memory cannot be erased by the Reset button.  
Display  
"V-ID ON"  
"V-ID OFF"  
Setting  
Guide is announced.  
Not be announced.  
1 Setup Sound Control  
Refer to the following operations to setup the  
Sound Control.  
- <Audio Control> (page 11)  
- <Audio Setup> (page 12)  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
In CD/ USB mode  
ACDrive firmware version display  
3 Select Audio Preset mode  
Push the Control knob towards [FM] or [AM].  
Select the "A-PRESET" display.  
Displaying the firmware version with the ACDrive  
function.  
1 Select the firmware version display mode  
Push the Control knob towards [FM] or [AM].  
Select the "ACD VER" display.  
4 Enter Audio Preset mode  
Press the Control knob for at least 1 second.  
5 Select the Audio Preset Memory  
Push the Control knob towards [FM] or [AM].  
Select the "MEMORY" display.  
2 Display the ACDrive firmware version  
Push the Control knob towards [4] or  
[¢].  
6 Put the Audio Preset in the memory  
Press the Control knob for at least 2 seconds.  
The "MEMORY" display blinks 1 time.  
In CD/ USB mode  
7 Exit Audio Preset mode  
Press the [MENU] button.  
Unique ID display  
Displaying the serial number for each product.  
Register 1 pair of Audio Preset Memory. You cannot  
register by the source.  
When you press the Reset, all the sources will be the  
setting value which is registered.  
The following items cannot be registered.  
Volume, Balance, Fader, Loudness, Volume offset, Dual  
Zone System, Rear Volume  
1 Select the unique ID display mode  
Push the Control knob towards [FM] or [AM].  
Select the "ACD ID" display.  
2 Display the unique ID  
Push the Control knob towards [4] or  
[¢].  
|
30  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other than Standby mode  
Audio Preset Recall  
Recalling the sound setup registered by <Audio  
Preset Memory> (page 30).  
1 Select the source  
Press the [SRC] button.  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
3 Select Audio Preset mode  
Push the Control knob towards [FM] or [AM].  
Select the "A-PRESET" display.  
4 Enter Audio Preset mode  
Press the Control knob for at least 1 second.  
5 Select the Audio Preset Recall  
Push the Control knob towards [FM] or [AM].  
Select the "RECALL" display.  
6 Recall the Audio Preset  
Press the Control knob for at least 2 seconds.  
The "RECALL" display blinks 1 time.  
7 Exit Audio Preset mode  
Press the [MENU] button.  
The User memory of <System Q> (page 11) is  
changed to the value which was recalled.  
The source tone memory item of <Audio Control>  
(page 11) is changed to the value which was recalled  
by the selected source.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
31  
Basic Operations of remote control  
SRC  
ATT  
VOL  
SRC  
AT T  
VOL  
38  
AUD  
AUD  
38  
FM+  
4
¢
4/¢  
AM–  
2-ZONE  
ABC  
FM/AM/+/–  
Not Used  
2-ZONE  
DIRECT  
/OK  
DIRECT  
DEF  
MNO  
WXY  
GHI  
JKL  
[0] — [9]  
PRS  
TUV  
QZ  
R.VOL  
Loading and Replacing the battery  
Basic operations  
Use two "AA"/ "R6"-size batteries.  
Slide the cover while pressing downwards to  
remove it as illustrated.  
Insert the batteries with the + and – poles aligned  
properly, following the illustration inside the case.  
[VOL] buttons  
Adjusts the volume.  
[SRC] button  
Each time you press the button, the source  
alternates.  
For the source alternating order refer to  
<Selecting the Source> (page 10).  
[ATT] button  
Turns the volume down quickly.  
When the button is pressed again, the volume  
returns to the previous level.  
2WARNING  
Store unused batteries out of the reach of children.  
Contact a doctor immediately if the battery is  
accidentally swallowed.  
Do not set the remote control in hot places such as  
on the dashboard.  
|
32  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Control  
In Disc/USB source  
[AUD] button  
Selects the Audio item to be adjusted.  
[4]/ [¢] buttons  
Going forwards and backwards between track/  
files.  
[VOL] buttons  
Adjusts the Audio item.  
[+]/ [] buttons  
Going forwards and backwards between disc/  
folders.  
Refer to <Audio Control> (page 11) for the operation  
method, such as the procedures for Audio control and  
others operations.  
The remote control can only select and adjust the  
Basic Audio item. Selecting and adjusting of the Detail  
Audio item cannot be done.  
[38] button  
Each time you press the button, the song pauses  
or plays.  
[0] — [9] buttons  
When in <Direct Track/File Search> (page 20) and  
<Direct Disc Search> (page 20), enters the track/  
file/disc number.  
Dual Zone System  
[2-ZONE] button  
Each time you press the button, "2ZON" of  
<Audio Setup> (page 12) is turned ON or OFF.  
In TV source  
[5]/ [] buttons  
[FM] button  
Adjusts the volume of the rear channel.  
The rear channel activates while the Dual Zone  
System is ON.  
Selects the TV band and Video input.  
Each time you press the [FM] button, TV bands  
and Video input alternates.  
[4]/ [¢] buttons  
Selects the TV channel.  
In Tuner source  
[0] — [9] buttons  
Press buttons [1] — [6] to recall preset TV  
channels.  
[FM]/ [AM] buttons  
Selects the band.  
Each time you press the [FM] button, the band  
alternates between the FM1, FM2, and FM3  
bands.  
[DIRECT] button  
Enters and cancels the <Direct TV Tuning> (page  
17) mode.  
[4]/ [¢] buttons  
Tune up or down band.  
[0] — [9] buttons  
Press buttons [1] — [6] to recall preset stations.  
[DIRECT] button  
Enters and cancels the <Direct Access Tuning>  
(page 16) mode.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
33  
Accessories/ Installation Procedure  
Accessories  
2WARNING  
If you connect the ignition wire (red) and the battery wire  
(yellow) to the car chassis (ground), you may cause a short  
circuit, that in turn may start a fire. Always connect those  
wires to the power source running through the fuse box.  
1
..........1  
..........1  
..........6  
..........6  
..........1  
If the power is not turned ON (or it is ON, but will be OFF  
immediately), the speaker wire may have a short circuit  
or touched the chasis of the vehicle and the protection  
function may have been activated. Therefore, the speaker  
wire should be checked.  
If your car’s ignition does not have an ACC position,  
connect the ignition wires to a power source that can be  
turned on and off with the ignition key. If you connect  
the ignition wire to a power source with a constant  
voltage supply, as with battery wires, the battery may die.  
If the console has a lid, make sure to install the unit so  
that the faceplate will not hit the lid when closing and  
opening.  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with  
one with the same rating.  
Insulate unconnected wires with vinyl tape or other  
similar material. To prevent a short circuit, do not remove  
the caps on the ends of the unconnected wires or the  
terminals.  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail  
to work if you share the - wires or ground them to any  
metal part in the car.  
When only two speakers are being connected to the  
system, connect the connectors either to both the front  
output terminals or to both the rear output terminals  
(do not mix front and rear). For example, if you connect  
the + connector of the left speaker to a front output  
terminal, do not connect the - connector to a rear  
output terminal.  
2
3
4
5
Installation Procedure  
1. To prevent a short circuit, remove the key from  
the ignition and disconnect the - battery.  
2. Make the proper input and output wire  
connections for each unit.  
3. Connect the speaker wires of the wiring harness.  
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
4. Connect the wiring harness wires in the  
following order: ground, battery, ignition.  
5. Connect the wiring harness connector to the  
unit.  
6. Install the unit in your car.  
7. Reconnect the - battery.  
8. Press the reset button.  
|
34  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Wires to Terminals  
AUX left input (White)  
AUX right input (Red)  
To connect these leads, refer to the  
relevant instruction manuals.  
To Kenwood disc changer/  
External optional accessory  
FM/AM  
antenna input  
Fuse (10A)  
Front left output (White)  
Front right output (Red)  
Rear left output/ Sub Woofer left output (White)  
Rear right output/ Sub Woofer right output (Red)  
Wiring harness  
(Accessory1)  
If no connections are made, do not let the wire come out from the tab.  
Power control wire (Blue/White)  
When using the optional power amplifier, connect  
to its power control terminal.  
P.CONT  
Depending on what antenna you are using,  
connect either to the control terminal of the  
motor antenna, or to the power terminal for the  
booster amplifier of the film-type antenna.  
Motor antenna control wire (Blue)  
TEL mute wire (Brown)  
ANT. CONT  
MUTE  
Connect to the terminal that is grounded when  
either the telephone rings or during conversation.  
To connect the Kenwood navigation  
system, consult your navigation manual.  
External amplifier control wire  
(Pink/Black)  
To "EXT.AMP.CONT." terminal of the amplifier  
having the external amp control function.  
EXT. CONT  
ILLUMI  
Dimmer control wire (Orange / White)  
To car light control switch  
White/Black  
White  
To front left  
speaker  
FRONT  
FRONT  
L
Gray/Black  
Gray  
To front right  
speaker  
R
Green/Black  
Green  
To rear left  
speaker  
REAR  
REAR  
L
Purple/Black  
Purple  
To rear right  
speaker  
R
Ignition key  
switch  
Ignition wire (Red)  
Battery wire (Yellow)  
Ground wire (Black) - (To car chassis)  
ACC  
Car fuse box  
(Main fuse)  
Car fuse box  
+
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
35  
Installation  
USB Device Connection  
When performing a check of the CD operation prior  
to installation, place this unit in a horizontal position  
and perform a loading/eject of the CD.  
1 Remove the cap and connect the USB cable  
(Accessory5).  
Installation  
Install onto the car bracket using the supplied  
screws (M5 × 6 mm, M5 × 7 mm). The holes of the  
car bracket to use will differ depending on the car  
model.  
When a ground wire is included in the wiring kit (which  
is sold separately), fasten the ground wire with the  
binding screw located on the rear panel of this unit.  
Screw (M4× 8)  
(commercially available)  
2 Connect the USB device to the unit using the  
supplied cable.  
Accessory3  
(M5 × 6 mm)  
or Accessory4  
(M5 × 7 mm)  
Accessory2  
(Only for NISSAN car)  
During installation, do not use any screws except for  
those provided. The use of different screws might result  
in damage to the main unit.  
Damage may occur if a screwdriver or similar tool is used  
with excessive force during the installations.  
|
36  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Guide  
What might seem to be a malfunction in your unit  
may just be the result of slight misoperation or  
miswiring. Before calling service, first check the  
following table for possible problems.  
? Even if Loudness is turned ON, high-pitched tone  
isn’t compensated for.  
Tuner source is selected.  
High-pitched tone isn’t compensated for when  
in Tuner source.  
? No sound can be heard, or the volume is low.  
General  
The fader or balance settings are set all the way to  
one side.  
? The power does not turn ON.  
Center the fader and balance settings.  
The fuse has blown.  
The input/output wires or wiring harness are  
connected incorrectly.  
After checking for short circuits in the wires,  
replace the fuse with one with the same  
rating.  
Reconnect the input/output wires or the  
wiring harness correctly. See the section on  
<Connecting Wires to Terminals> (page 35).  
? There’s a source you can’t switch.  
There’s no media inserted.  
The values of Volume offset are low.  
Set the media you want to listen to. If there’s  
no media in this unit, you can’t switch to each  
source.  
Turn up the Volume offset, referring to the  
section on <Audio Setup> (page 12).  
The <Built-in Amp Setting> (page 28) is OFF.  
Turn it ON.  
The Disc changer isn’t connected.  
Connect the Disc changer. If the Disc changer  
isn’t connected to it’s input terminal, You can’t  
switch to an external disc source.  
? The sound quality is poor or distorted.  
One of the speaker wires is being pinched by a  
screw in the car.  
? The memory is erased when the ignition is  
turned OFF.  
Check the speaker wiring.  
The speakers are not wired correctly.  
The ignition and battery wire are incorrectly  
Reconnect the speaker wires so that each  
output terminal is connected to a different  
speaker.  
connected.  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>  
(page 35).  
? The Touch Sensor Tone doesn’t sound.  
The preout jack is being used.  
? There’s no loudness effect.  
You’re using Subwoofer preout.  
Loudness has no effect in Subwoofer preout.  
The Touch Sensor Tone can’t be output from  
the preout jack.  
The <Touch Sensor Tone> (page 27) is OFF.  
Turn it ON.  
? The TEL mute function does not work.  
The TEL mute wire is not connected properly.  
? The Dimmer function does not work.  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>  
(page 35).  
The Dimmer wire is not connected correctly.  
Check the Dimmer wire connection.  
The <Dimmer> (page 27) is OFF.  
Turn it ON.  
? The TEL mute function turns ON even though the  
TEL mute wire is not connected.  
? The sound is not output from Subwoofer or it  
outputs the different sound.  
The TEL mute wire is touching a metal part of the  
car.  
When "2ZON" of <Audio Setup> (page12) is set to  
Pull the TEL mute wire away from the metal  
part of the car.  
ON.  
Set "2ZON" of <Audio Setup> to OFF.  
? The display blacks out while scrolling.  
<Display Illumination Control> is set to OFF.  
Refer to <Display Illumination Control> (page  
27).  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
37  
Troubleshooting Guide  
Tuner source  
Disc source  
? Radio reception is poor.  
? "AUX EXT" is displayed without achieving  
The car antenna is not extended.  
External disc control mode.  
Pull the antenna out all the way.  
Unsupported disc changer is connected.  
The antenna control wire is not connected.  
Use the disc changer mentioned in the  
<About CD players/disc changers connected  
to this unit> (page 3) of the section on <Safety  
precautions>.  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>  
(page 35).  
? The desired frequency can’t be entered with the  
Direct Access Tuning.  
? The specified disc does not play, but another one  
plays instead.  
A station that can’t be received is being entered.  
The specified CD is quite dirty.  
Enter a station that can be received.  
Clean the CD.  
You’re trying to enter a frequency with a 0.01 MHz  
unit.  
The disc is loaded in a different slot from that  
specified.  
What can be designated in the FM band is to  
0.1 MHz.  
Eject the disc magazine and check the  
number for the specified disc.  
The disc is severely scratched.  
Try another disc instead.  
? A CD ejects as soon as it is loaded.  
The CD is quite dirty.  
Clean the CD, referring to the CD cleaning of  
the section on <About CDs> (page 6).  
? Can’t remove disc.  
The cause is that more than 10 minutes has  
elapsed since the vehicle ACC switch was turned  
OFF.  
The disc can only be removed within 10  
minutes of the ACC switch being turned OFF.  
If more than 10 minutes has elapsed, turn  
the ACC switch ON again and press the Eject  
button.  
? The disc won’t insert.  
There’s already another disc inserted.  
Press the [0] button and remove the disc.  
? Direct Search can’t be done.  
Another function is ON.  
Turn Random Play or other functions OFF.  
? Track Search can’t be done.  
For the discs/folders first or last song.  
For each disc/folder, Track Search can’t be  
done in the backward direction for the first  
song or in the forward direction for the last  
song.  
|
38  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio file source  
The messages shown below display your  
systems condition.  
? Cannot play an Audio file.  
The media is scratched or dirty.  
EJECT:  
No disc magazine has been loaded in  
the changer. The disc magazine is not  
completely loaded.  
Clean the media, referring to the CD cleaning  
of the section on <About CDs> (page 6).  
Load the disc magazine properly.  
No CD in the unit.  
Insert the CD.  
? The sound skips when an Audio file is being  
played.  
The media is scratched or dirty.  
Clean the media, referring to the CD cleaning  
of the section on <About CDs> (page 6).  
NO DISC:  
TOC ERR:  
No disc has been loaded in the disc  
magazine.  
Load a disc into the disc magazine.  
The recording condition is bad.  
Record the media again or use another media.  
No disc has been loaded in the disc  
magazine.  
Load a disc into the disc magazine.  
The CD is quite dirty. The CD is upside-  
down. The CD is scratched a lot.  
Clean the CD and load it correctly.  
? The Audio file track time isn’t displayed correctly.  
---  
There are times when it isn’t displayed  
correctly according to the Audio file recording  
conditions.  
READ ERR:  
• The number of files or folders which are  
stored in the connected USB device is  
above the limitation.  
• The file system of the connected USB  
device is broken.  
Copy the files and folders for the USB  
kenwood.com/usb/. If the error  
message is still displayed, initialize the  
USB device or use other USB devices.  
USB device source  
? The USB device is not detected.  
The USB connector is disconnected.  
Connect the connector of the USB device  
properly.  
? The USB device does not play its audio files.  
The USB connector is disconnected.  
Connect the connector of the USB device  
properly.  
E-05:  
The CD is upside-down.  
Load the CD correctly.  
BLANK:  
Nothing has been recorded on the MD.  
NO TRACK:  
No tracks are recorded on the MD,  
although it has a title.  
NO PANEL:  
E-77:  
The faceplate of the slave unit being  
connected to this unit has been removed.  
Replace it.  
The unit is malfunctioning for some reason.  
Press the reset button on the unit. If the  
"E-77" code does not disappear, consult  
your nearest service center.  
E-99:  
Something is wrong with the disc  
magazine. Or the unit is malfunctioning for  
some reason.  
Check the disc magazine. And then  
press the reset button on the unit. If the  
"E-99" code does not disappear, consult  
your nearest service center.  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
39  
Troubleshooting Guide  
HOLD:  
The protective circuit in the unit activates  
NO MUSIC:  
E-15:  
when the temperature inside the  
automatic disc changer exceeds 60°C  
(140°F), stopping all operation.  
Cool down the unit by opening  
the windows or turning on the air  
conditioner. As the temperature falls  
below 60°C (140°F), the disc will start  
playing again.  
• The connected USB device contains no  
playable audio file.  
• Media was played that doesn’t have data  
recorded that the unit can play.  
Use media that has data recorded that  
the unit can play.  
USB ERR:  
The connected USB device is rated a  
current capacity higher than the allowable  
limit.  
Check the USB device with reference to  
<About USB device> (page 7).  
Some trouble may have occurred to the  
connected USB device.  
Remove the USB device and then  
reconnect it. When the same message  
displays again, use another USB device.  
LOAD:  
Discs are being exchanged in the Disc  
changer.  
READING:  
IN (Blink):  
The unit is reading the data on the disc.  
The CD player section is not operating  
properly.  
Reinsert the CD. If the CD cannot be  
ejected or the display continues to flash  
even when the CD has been properly  
reinserted, please switch off the power  
and consult your nearest service center.  
PROTECT:  
The speaker wire has a short-circuit or  
touches the chassis of the vehicle, and  
then the protection function is activated.  
Wire or insulate the speaker cable  
properly and press the reset button.  
NA FILE:  
An Audio file is played with a format that  
this unit can’t support.  
----  
COPY PRO:  
NO DVICE:  
A copy-protected file is played.  
----  
The USB device is selected as a source  
although no USB device is connected.  
Change the source to any source other  
than USB. Connect an USB device, and  
change the source to USB again.  
NA DVICE:  
An unsupported USB device is connected.  
For the supported USB devices, refer to  
<About USB device> (page 7).  
|
40  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Specifications subject to change without notice.  
FM tuner section  
USB Interface  
Frequency range  
(50 kHz space) : 87.5 MHz – 108.0 MHz  
USB Standard  
: USB 1.1/ 2.0  
(200 kHz space): 87.9 MHz – 107.9 MHz  
Usable sensitivity (S/N = 30dB)  
: 9.3dBf (0.8 μV /75 Ω)  
Quieting Sensitivity (S/N = 50dB)  
: 15.2dBf (1.6 μV /75 Ω)  
Frequency response ( 3.0 dB)  
: 30 Hz – 15 kHz  
Signal to Noise ratio (MONO)  
: 70 dB  
Selectivity ( 400 kHz)  
: ≥ 80 dB  
Maximum Supply current  
: 500 mA  
File System  
: FAT16/ 32  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
AAC decode  
: AAC-LC ".m4a" files  
Stereo separation (1 kHz)  
: 40 dB  
Audio section  
Maximum output power  
: 50 W x 4  
Full Bandwidth Power (at less than 1% THD)  
: 22 W x 4  
Speaker impedance  
: 4 – 8 Ω  
Tone action  
Bass : 100 Hz 8 dB  
Middle : 1 kHz 8 dB  
Treble : 10 kHz 8 dB  
Preout level / Load (during disc play)  
: 2500 mV/10 kΩ  
Preout impedance  
: ≤ 600 Ω  
AM tuner section  
Frequency range  
(9 kHz space) : 531 kHz – 1611 kHz  
(10 kHz space): 530 kHz – 1700 kHz  
Usable sensitivity (S/N = 20dB)  
: 28 dBμ (25 μV)  
CD player section  
Laser diode  
: GaAlAs  
Digital filter (D/A)  
: 8 Times Over Sampling  
D/A Converter  
: 1 Bit  
Auxiliary input  
Spindle speed (Audio file)  
: 1000 – 400 rpm (CLV 2times)  
Frequency response ( 1 dB)  
: 20 Hz – 20 kHz  
Wow & Flutter  
: Below Measurable Limit  
Input Maximum Voltage  
: 1200 mV  
Frequency response ( 1 dB)  
: 10 Hz – 20 kHz  
Input Impedance  
: 100 kΩ  
Total harmonic distortion (1 kHz)  
: 0.008 %  
Signal to Noise ratio (1 kHz)  
: 105 dB  
Dynamic range  
: 93 dB  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
AAC decode  
: AAC-LC ".m4a" files  
General  
Operating voltage (11 – 16V allowable)  
: 14.4 V  
Current consumption  
: 10 A  
Installation Size (W x H x D)  
: 178 x 100 x 155 mm  
Weight  
: 1.60 kg  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
|
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Washer INDESIT Washing Machine User Manual
Intel Network Card LPCI 7200S User Manual
Invacare Camping Equipment BariatricBed User Manual
Jabra Automobile Accessories 81 00277 User Manual
Jenn Air Dishwasher W10208727A User Manual
JL Audio Car Speaker SB D CLGR 12W3V3 User Manual
JVC Laptop MP XP3210GB User Manual
Kenwood Cassette Player KRC 160 User Manual
Kodak Printer VT3000 User Manual
Kramer Electronics Stereo System RC 2C User Manual