Kenwood Car Stereo System DPX 3070 User Manual

DPX-MP4070

DPX-MP4070B

DPX-3070

DPX-3070B

DOUBLE DIN SIZED CD/CASSETTE RECEIVER

INSTRUCTION MANUAL

雙 DIN 規格 CD/ 錄音座接收機

使用說明書

더불�DIN�사이주 CD/ 카세트�리시버

조작�매뉴얼

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

2WARNING

2CAUTION

To prevent injury or fire, take the

following precautions:

• Insert the unit all the way in until it is fully locked

in place. Otherwise it may fall out of place when

jolted.

To prevent damage to the machine, take

the following precautions:

• Make sure to ground the unit to a negative 12V

DC power supply.

• Do not open the top or bottom covers of the unit.

• When extending the ignition, battery, or ground

wires, make sure to use automotive-grade wires

or other wires with a 0.75mm² (AWG18) or more

to prevent wire deterioration and damage to the

wire coating.

• To prevent a short circuit, never put or leave any

metallic objects (such as coins or metal tools)

inside the unit.

• If the unit starts to emit smoke or strange smells,

turn off the power immediately and consult your

Kenwood dealer.

• Make sure not to get your fingers caught between

the faceplate and the unit.

• Do not install the unit in a spot exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of

water splashing.

• When replacing a fuse, only use a new one with

the prescribed rating. Using a fuse with the wrong

rating may cause your unit to malfunction.

• To prevent a short circuit when replacing a fuse,

first disconnect the wiring harness.

• Do not use your own screws. Use only the screws

provided. If you use the wrong screws, you could

damage the unit.

• Be careful not to drop the unit or subject it to

strong shock.

The unit may break or crack because it contains

glass parts.

• Do not touch the liquid crystal fluid if the LCD

is damaged or broken due to shock. The liquid

crystal fluid may be dangerous to your health or

even fatal.

If the liquid crystal fluid from the LCD contacts

your body or clothing, wash it off with soap

immediately.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

About CD players/disc changers

connected to this unit

KENWOOD disc changers/ CD players released in

1998 or later can be connected to this unit.

Refer to the catalog or consult your Kenwood

dealer for connectable models of disc changers/

CD players.

Note that any KENWOOD disc changers/ CD players

released in 1997 or earlier and disc changers made

by other makers cannot be connected to this unit.

Unsupported connection may result in damage.

Setting the "O-N" Switch to the "N" position for the

applicable KENWOOD disc changers/ CD players.

The functions that can be used and the information

that can be displayed will differ depending on the

models being connected.

NOTE

• If you experience problems during installation,

consult your Kenwood dealer.

• If the unit fails to operate properly, press the Reset

button. The unit returns to factory settings when

the Reset button is pressed. If the unit still fails to

operate properly after the Reset button has been

pressed, contact your local KENWOOD dealer for

assistance.

• Press the reset button if the Disc auto changer

fails to operate correctly. Normal operation should

be restored.

•

You can damage both your unit and the CD changer if

you connect them incorrectly.

Reset button

• Characters in the LCD may become difficult to

read in temperatures below 41 ˚F (5 ˚C).

• The illustrations of the display and the panel

appearing in this manual are examples used to

explain more clearly how the controls are used.

Therefore, what appears on the display in the

illustrations may differ from what appears on

the display on the actual equipment, and some

of the illustrations on the display may represent

something impossible in actual operation.

Lens Fogging

Right after you turn on the car heater in cold

weather, dew or condensation may form on the

lens in the Disc player of the unit. Called lens

fogging, Discs may be impossible to play. In such

a situation, remove the disc and wait for the

condensation to evaporate. If the unit still does

not operate normally after a while, consult your

Kenwood dealer.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

About Cassette tape

Cleaning the Unit

Cleaning the tape head

If the faceplate of this unit is stained, wipe it with a

dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the stain off

with a cloth moistened with neutral cleaner, then

wipe neutral detergent off.

When there’s noise or the sound quality is bad

during tape play the tape head maybe dirty, clean

the tape head.

About Cassette tape

• If the tape is slack tighten it.

•

Applying spray cleaner directly to the unit may affect its

mechanical parts. Wiping the faceplate with a hard cloth

or using a volatile liquid such as thinner or alcohol may

scratch the surface or erases characters.

• If the cassette tape label is peeling off glue it on

again.

• Don’t use deformed cassette tape.

• Don’t place cassette tape on the dashboard etc.

where the temperature is high.

Cleaning the CD Slot

• Don’t use cassette tape that’s 100 minutes long or

longer.

As dust tends to accumulate in the CD slot, clean it

every once in a while. Your CDs can get scratched if

you put them in a dusty CD slot.

The marking of products using lasers

(Except for some areas)

CLASS 1

LASER PRODUCT

The label is attached to the chassis/case and says

that the component uses laser beams that have

been classified as Class 1. It means that the unit

is utilizing laser beams that are of a weaker class.

There is no danger of hazardous radiation outside

the unit.

WOW, SRS and

Labs, Inc.

symbol are trademarks of SRS

WOW technology is incorporated under license

from SRS Labs, Inc.

Manufactured under license from Dolby

Laboratories.

"Dolby" and the double-D symbol are trademarks of

Dolby Laboratories.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on playing MP3/WMA (DPX-MP4070/DPX-MP4070B)

Note, however, that the MP3/WMA recording

media and formats acceptable are limited. When

writing MP3/WMA, pay attention to the following

restrictions.

When you use your CD writer to record MP3/WMA

up to the maximum disc capacity, disable additional

writing. For recording on an empty disc up to the

maximum capacity at once, check Disc at Once.

Acceptable media

The MP3/WMA recording media acceptable to this

unit are CD-ROM, CD-R, and CD-RW.

When using CD-RW, do full format not quick format

to prevent malfunction.

•

Play mode may not be possible when portions of the

functions of Windows Media Player 9 or higher are used.

Entering ID3 tag

The Displayable ID3 tag is ID3 version 1.x.

For the character code, refer to the List of Codes.

Acceptable medium formats

The following formats are available for the media

used in this unit. The maximum number of

characters used for file and folder name including

the delimiter (".") and three-character extension are

indicated in parentheses.

• ISO 9660 Level 1 (12 characters)

• ISO 9660 Level 2 (31 characters)

• Joliet (64 character; Up to 32 characters are

displayed)

• Romeo (128 character; Up to 64 characters are

displayed)

• Long file name (200 characters; Up to 64

characters are displayed)

• Maximum number of characters for folder name:

64 (Joliet; Up to 32 characters are displayed)

For a list of available characters, see the instruction

manual of the writing software and the section

Entering file and folder names below.

The media reproducible on this unit has the

following limitations:

Entering file and folder names

The code list characters are the only file names and

folder names that can be entered and displayed.

If you use any other character for entry, the file and

folder names are not displayed correctly. They may

neither be displayed correctly depending on the CD

writer used.

The unit recognizes and plays only those MP3/WMA

which have the MP3/WMA extension (.MP3/.WMA).

• Maximum number of directory levels: 8

• Maximum number of files per folder: 255

• Maximum number of folders: 50

•

A file with a name entered with characters not on the

code list may not play correctly.

Writing files into a medium

• Maximum number of files and folders: 512

When a medium containing MP3/WMA data is

loaded, the unit checks all the data on the medium.

If the medium contains a lot of folders or non-MP3/

WMA files, therefore, it takes a long time until the

unit starts playing MP3/WMA.

MP3/WMA written in the formats other than the

above may not be successfully played and their file

names or folder names are not properly displayed.

Settings for your MP3/WMA encoder and

CD writer

Do the following setting when compressing

audio data in MP3/WMA data with the MP3/WMA

encoder.

In addition, it may take time for the unit to move

to the next MP3/WMA file or a File Search or Folder

Search may not be performed smoothly.

• Transfer bit rate: MP3: 8 —320 kbps

WMA: 48 —192 kbps

• Sampling frequency

MP3: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz

WMA: 32, 44.1, 48 kHz

Loading such a medium may produce loud noise to

damage the speakers.

•

Do no attempt to play a medium containing a non-MP3

file with the MP3 extension.

The unit mistakes non-MP3 files for MP3/WMA data as

long as they have the MP3 extension.

•

Do not attempt to play a medium containing non MP3.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3/WMA playing order

When selected for play, Folder Search, File Search,

or for Folder Select, files and folders are accessed

in the order in which they were written by the CD

writer.

Because of this, the order in which they are

expected to be played may not match the order in

which they are actually played. You may be able to

set the order in which MP3/WMA are to be played

by writing them onto a medium such as a CD-R

with their file names beginning with play sequence

numbers such as "01" to "99", depending on your

CD writer.

When a File Search is executed with file ¡$

being played ...

Operation of

(Current file: ¡$)

the button

4 Button

¢ Button

Beginning of file ¡$  ¡#

¡%  ¡&

When a Folder Search is executed with file ¡$

being played ...

Operation of

(Current folder: 4)

the button

For example, a medium with the following folder/

file hierarchy is subject to Folder Search, File Search,

or Folder Select as shown below.

AM Button

FM Button

3  2  1  8

5  6  7  8  1

Example of a medium’s folder/file hierarchy

��

When Folder Select is selected with file ¡$

��

being played to move from folder to folder ...

��

Operation of

(Current folder: 4)

the button

Button

AM Button

FM Button

��

English

Download from Www.Somanuals.com. All Manuals Search And Download.

About CDs

Handling CDs

• Don’t touch the recording surface of the CD.

Removing CDs

When removing CDs from this unit pull them out

horizontally.

CDs that can’t be used

• CDs that aren’t round can’t be used.

• CD-R and CD-RW are easier to damage than a

normal music CD. Use a CD-R or a CD-RW after

reading the caution items on the package etc.

• Don’t stick tape etc. on the CD.

Also, don’t use a CD with tape stuck on it.

CDs with coloring on the recording surface or that

are dirty can’t be used.

• This unit can only play the CDs with

When using a new CD

If the CD center hole or outside rim has burrs, use it

after removing them with a ball pen etc.

It may not correctly play discs which do not have

the mark.

• A CD-R or CD-RW that hasn’t been finalized can’t

be played. (For the finalization process refer to

your CD-R/CD-RW writing software, and your CD-

R/CD-RW recorder instruction manual.)

Burrs

CD storage

• Don’t place them in direct sunlight (On the seat

or dashboard etc.) and where the temperature is

high.

• Store CDs in their cases.

CD accessories

Don’t use disc type accessories.

CD cleaning

Clean from the center of the disc and move

outward.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

�

� � �

��

ATT indicator

Power

Volume

Turning ON the Power

Increasing Volume

Press the [SRC] button.

Press the [

] button.

Turning OFF the Power

Decreasing Volume

Press the [SRC] button for at least 1 second.

Press the [

∞

] button.

Attenuator

Selecting the Source

Turning the volume down quickly.

Press the [SRC] button.

Press the [ATT] button.

Each time the button is pressed the Attenuator

turns ON or OFF.

Source required

Tuner

Tape

Display

"TUNER"

"TAPE"

When it’s ON, the "ATT" indicator blinks.

"CD"

External disc (Optional accessory)

Auxiliary input

"CD CH"

"AUX"

Standby (Illumination only mode)

"STANDBY"

English

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Audio Control

TEL Mute

The audio system automatically mutes when a

call comes in.

1 Enter the Audio Control mode

Press the [AUD] button for at least 1 second.

"AUD mode" is displayed.

When a call comes in

"CALL" is displayed.

The audio system pauses.

Select the Audio item for adjustment

Press the [FM+] or [AM–] button.

Each time the button is pressed, the items that

can be adjusted switch as shown below.

Listening to the audio during a call

Press the [SRC] button.

The "CALL" display disappears and the audio

system comes back ON.

3 Adjust the Audio item

Press the [

] or [

] button.

When the call ends

Hang up the phone.

The "CALL" display disappears and the audio

system comes back ON.

Adjustment Item

Balance

Fader

Sub woofer level*¹

Bass boost level*²

Central frequency boost*²

"AmpF"

Display

"BAL"

"FAD"

"SubW"

"AmpB"

Range

Left 15 — Right 15

Rear 15 — Front 15

–15 — +15

Flat/+6/ +12/ +18 (dB)

Normal/ Low

Low Pass Filter*¹

Volume offset

"LPF"

"V-OFF"

Through/120/80/50 Hz

–8 — ±0

SRS WOW Select

You can play back adding gorgeous heavy bass to

the sound and making a 3D sound field.

•

*¹ You can control this item when 'Subwoofer Output'

(page 10) is set to "SubW On".

Volume offset: Each source’s volume can be set as a

difference from the basic volume.

*² - Refer to the catalog or instruction manual for

power amplifiers that can be controlled from this

unit.

- For amplifiers there are the model that can be set

from Flat to +18 dB, and the model that can be set

from Flat to +12 dB.

1 Enter the WOW Select mode

Press the [WOW] button.

"WOW SEL" is displayed.

Select the WOW item

Press the [WOW] button.

Each time the button is pressed, the SRS WOW

Select switch as shown below:

When an amplifier that can only be set to +12 is

connected to the unit, "AmpB +18" won't work

correctly even if it's selected.

SRS WOW

Display

Moves the sound image up a notch and adjusts

bass and the sound field.

"Low"

Exit the Audio Control mode

Press the [AUD] button.

Moves the sound image up two notches and

adjusts bass and the sound field.

"High"

Changes to the value set in 'SRS WOW Control'. "User"

Returns to the normal sound without SRS WOW. "Off"

Subwoofer Output

•

When operation stops for 3 seconds, the SRS WOW

Select closes.

WOW: TruBass, FOCUS and SRS 3D are all set to values

shown below.

Turning the Subwoofer output ON or OFF.

Press the [AM–] button for at least 1 second.

Each time the button is pressed Subwoofer

output switches ON or OFF.

SRS WOW

High

Low

SRS FOCUS SRS TruBass SRS 3D

When it’s ON, "SubW On" is displayed.

High

Low

Off

•

You can control this function when 'Switching preout'

(page 24) is set to "SWPRE SW".

English

Download from Www.Somanuals.com. All Manuals Search And Download.

SRS WOW Control

Soft

"Soft"

Sharp

Light

Natural

"Sharp"

"Light"

"Natural"

Adjusts each function of SRS WOW individually.

1 Enter the WOW Control mode

Press the [WOW] button for at least 1 second.

"WOW CTRL" is displayed.

•

"User" display: The values set on the 'Adjustment of

Equalizer type at PRO' (page 12).

A selected Equalizer type can be adjusted.

Select the WOW item for adjustment

Press the [FM+] or [AM–] button.

Each time the button is pressed, the items that

can be adjusted switch as shown below.

Adjustment items depend on the setting of 'Equalizer

mode' (page 24). Refer to 'Adjustment of Equalizer

type at EASY' (page 11) or 'Adjustment of Equalizer

type at PRO' (page 12) for details of adjustment.

Adjust the WOW item

Press the [

] or [

] button.

Exit the Equalizer Control mode

Adjustment Item

SRS FOCUS setting

SRS TruBass setting

SRS 3D setting

Display

"FOCUS"

"TB"

Range

0(Off)/1(Low)/2(High)

Off/On

Press the [EQ] button for at least 1 second.

When operation stops for 10 seconds, the

Equalizer type at that time is registered and the

Equalizer Control mode automatically closes.

"SRS"

Off/On

Exit the WOW Control mode

Press the [WOW] button.

Adjustment of Equalizer type at

EASY

•

TruBass: Assisting the playback for the super bass

sound.

FOCUS: Adjusts the sound image by changing the

vertical position of the speakers virtually and

increases or decreases the soundscape.

SRS 3D: Making a natural 3D sound field.

SRS 3D cannot be set in tuner source.

Adjusting the effect of an Equalizer type selected

in 'Equalizer Control' when 'Equalizer mode' is

"EASY".

•

1 Refer to 'Equalizer Control' (page 11) to

select the Equalizer type.

Adjust the effect

Press the [FM+] or [AM–] button.

Each time the button is pressed, the effects of

Equalizer switch as shown below:

Equalizer Control

You can recall the best sound setting preset for

different types of the music.

Setting of effect

High

Display

"Hi"

1 Enter the Equalizer Control mode

Press the [EQ] button.

"EQ EASY" or "EQ PRO" is displayed.

Middle

Low

"Mid"

"Lo"

Select the Equalizer type

Press the [EQ] button.

Each time the button is pressed, the Equalizer

type switches as shown below:

3 Exit the Equalizer Control mode

Press the [EQ] button for at least 1 second.

When operation stops for 10 seconds, the

Equalizer type at that time is registered and the

Equalizer Control mode automatically closes.

Equalizer type

Rock

Dance

Display

"Rock"

"Dance"

"Jazz"

Jazz

Pops

Heavy

"Pops"

"Heavy"

English

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Adjustment of Equalizer type at PRO Memory preset of adjustment of

Equalizer type

Adjusting the effect of an Equalizer type selected

in 'Equalizer Control' when 'Equalizer mode' is

"PRO".

The 'Adjustment of Equalizer type at PRO' can be

preset.

1 Refer to 'Equalizer Control' (page 11) to

select the Equalizer type.

1 Refer to 'Adjustment of Equalizer type at

PRO' (page 12) to adjust the Equalizer type.

Select the item for adjustment

Press the [FM+] or [AM–] button.

Each time the button is pressed, the items that

can be adjusted switch as shown below.

Preset the adjusted value

Press the [1] — [3] button for at least 1

second.

Recalling a setting value

Adjust the item

Press the [

] or [

] button.

1 Enter the Equalizer Control mode

Press the [EQ] button.

"EQ PRO" is displayed.

Adjustment Item

Bass Center Frequency

Bass level

Bass Q Factor

Bass Extend

Display

"BasF"

"BasLV"

"BasQ"

"EXT"

Range

60/70/80/100 or 150 Hz

–12 — +12

1.00/1.25/1.50/2.00

ON/OFF

•

If "EQ EASY" is displayed, refer to 'Equalizer mode'

(page 24) to set the mode to "EQ PRO".

Middle Center Frequency "MidF"

0.5/1.0/1.5/2.0 kHz

–12 — +12

1.0/2.0

2 Recall the setting value

Press the [1] — [3] button.

Middle level

"MidLV"

"MidQ"

Middle Q Factor

Treble Center Frequency "TreF"

Treble level "TreLV"

10.0/12.5/15.0/17.5 kHz

–12 — +12

Movie Select

Selecting the Movie display.

•

According to the Bass Q Factor setting value, the

frequencies that can be set in Bass Center Frequency

change as shown below.

1 Enter the Movie Select mode

Press the [MOVIE] button for at least 1

second.

Bass Q Factor

1.00/1.25/1.50

2.00

Bass Center Frequency

60/70/80/100

60/70/80/150

"Movie" is displayed.

2 Select the Movie

•

When the Bass Extend is set to ON, low frequency

response is extended by 20%.

Press the [MOVIE] button.

Each time the button is pressed, the Movie

switch as shown below:

Exit the Equalizer Control mode

Press the [EQ] button for at least 1 second.

When operation stops for 10 seconds, the

Equalizer type at that time is registered and the

Equalizer Control mode automatically closes.

Movie

Display

Scan of Movie

Movie 1

Movie 2

Movie 3

Movie 4

Movie 5

Movie 6

Movie 7

Movie 8

OFF

"MovieScn"

"Movie 1"

"Movie 2"

"Movie 3"

"Movie 4"

"Movie 5"

"Movie 6"

"Movie 7"

"Movie 8"

"MovieOff"

English

Download from Www.Somanuals.com. All Manuals Search And Download.

In Tape source

3 Exit the Movie Select mode

Press the [MOVIE] button for at least 1

second.

When operation stops for 10 seconds, Movie

at that time is registered and the Movie Select

mode automatically closes.

Information

Play side & Tape counter

Character

Clock

In Auxiliary input source

Information

Auxiliary input name

Character

Switching Display

Clock

Switching the information displayed.

In Standby mode

Press the [DISP] button.

Information

Character & Graphic

Clock & Graphic

Clock

Each time the button is pressed the display

switches as shown below.

In Tuner source

Information

Frequency

Display

Station name or Frequency

Character

Clock

"SNPS"

•

If the Disc title, Track title, Song title & Artist name, or

Album name & Artist name is selected when the disc

which does not have Disc title, Track title, Song title,

Album name, or Artist name is played, track number

and play time are displayed.

In CD & External disc source

Information

Play time & Track number

Disc name

Disc title

Track title

Display

"DNPS"

"D-Title"

"T-Title"

Character

Clock

In MP3/WMA source (DPX-MP4070/DPX-

MP4070B)

Information

Play time & Track number

Folder name

Display

"Folder"

"File"

File name

Song title & Artist name

Album name

Character

"Title"

"Album"

Clock

English

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Illumination Color Select

Select the Color for adjustment

Press the [

] or [

] button.

Setting the color of the display.

Each time the button is pressed, the colors that

can be adjusted switch as shown below:

1 Enter the Illumination Color Select mode

Press the [COL] button.

"Illumi" is displayed.

Adjustment Color

Display

Red

Green

Blue

"R" is blinks

"G" is blinks

"B" is blinks

Select the Illumination Color

Press the [COL] button.

Each time the button is pressed, the Illumination

Color switches as shown below:

Adjust the Color

Press the [FM+] or [AM–] button.

Each time the button is pressed, the intensity of

color changes as shown below:

Illumination Color

Scan of“Blue”to“Mint

Blue

Display

"V.Color"

"Blue"

Intensity of color

Turning off

Weak

Display

"X0"

"X1"

Mars Red

White

Lavender

Muscat

"Mars Red"

"White"

"Lavender"

"Muscat"

"Pink"

Dark

"X4"

Pink

Sky Blue

Lime

Violet

Aqua

Orange

"Sky Blue"

"Lime"

"Violet"

"Aqua"

"Orange"

"Mint"

4 Exit the Illumination Color Select mode

Press the [COL] button for at least 1 second.

When operation stops for 10 seconds, the

Illumination Color at that time is determined and

the Illumination Color Select mode automatically

closes.

Mint

User Color

"RX/GX/BX"

•

"User Color" enables the color set in 'User Illumination

Color Setting' (page 14) to be recalled.

Adjusting Clock

Exit the Illumination Color Select mode

Press the [COL] button for at least 1 second.

When operation stops for 10 seconds, the

Illumination Color at that time is registered and

the Illumination Color Select mode automatically

closes.

Select the clock display

Press the [DISP] button.

2 Enter clock adjustment mode

Press the [DISP] button for at least 1 second.

The ‡ indicator blinks.

3 Adjust the hours

Press the [FM+] or [AM–] button.

Adjust the minutes

Press the [

] or [

] button.

User Illumination Color Setting

The Illumination Color by the adjustment of RGB

can arbitrarily set.

Exit clock adjustment mode

Press the [DISP] button.

1 Enter the Illumination Color Select mode

Press the [COL] button.

"Illumi" is displayed.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

•

Memory numbers

- FM & AM: 30 stations

- Internal CD player: 10 discs

- External CD changer/ player: Varies according to the

CD changer/ player. Refer to the CD changer/ player

manual.

The title of station/CD can be changed by the same

operation used to name it.

Station/Disc Naming (SNPS/DNPS)

Attaching a title to a Station or CD.

1 Receive/play the station/disc you want to

attach a title to

•

Refer to the 'Switching Display' (page 13) and select

either "DNPS" or "SNPS". No name can be attached to

the source if "DNPS" or "SNPS" cannot be selected for

it.

Auxiliary Input Display Setting

Enter name set mode

Press the [NAME.S] button for at least 2

seconds.

Selecting the display when this device is switched

to Auxiliary input source.

"Name Set" is displayed.

1 Select Auxiliary input source

Press the [SRC] button.

Select the "AUX" display.

Move the cursor to the enter character

position

Press the [

] or [

] button.

Enter Auxiliary input display setting mode

Press the [NAME.S] button for at least 2

seconds.

4 Select the character type

Press the [38] button.

Each time the button is pressed the character

type switches as shown below.

"Name Set" is displayed

Select the Auxiliary input display

Character type

Alphabet upper case

Alphabet lower case

Display

"A"

"a"

Press the [

] or [

] button.

Each time the button is pressed it switches

through the below displays.

• "AUX"

• "TV"

• "VIDEO"

• "GAME"

• "PORTABLE"

• "DVD"

5 Select the characters

Press the [FM+] or [AM–] button.

•

Characters can be entered by using a remote with a

number buttons.

Example: If "DANCE" is entered.

4 Exit Auxiliary input display setting mode

Press the [NAME.S] button.

Character

"D"

Button

[3]

Times pressed

"A"

[2]

•

When operation stops for 10 seconds, the name

at that time is selected, and Auxiliary input display

setting mode closes.

The Auxiliary Input Display can be set only when the

built-in auxiliary input or the auxiliary input of optional

KCA-S210A is used.

"N"

[6]

"C"

[2]

"E"

[3]

6 Repeat steps 3 through 5 and enter the name.

If this unit is removed from the battery, the Auxiliary

Input name is returned to "AUX".

Exit name set mode

Press the [NAME.S] button.

•

When operation stops for 10 seconds the name at

that time is registered, and Name Set mode closes.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

��

� � �

��

�

Preset station number

AUTO indicator

Band display

ST indicator

Frequency display

Function of remote

Tuning

Direct Access Tuning

Selecting the station.

Entering the frequency and tuning.

1 Select tuner source

Press the [SRC] button.

Select the "TUNER" display.

Select the band

Press the [FM] or [AM] button.

Select the band

Enter Direct Access Tuning mode

Press the [DIRECT] button on the remote.

"– – – –" is displayed.

Press the [FM+] or [AM–] button.

Each time the [FM+] button is pressed it switches

between the FM1, FM2, and FM3 bands.

3 Enter the frequency

Press the number buttons on the remote.

Example:

Tune up or down band

Press the [

] or [

] button.

Desired frequency

92.1 MHz (FM)

810 kHz (AM)

Press button

[9], [2], [1]

[8], [1], [0]

•

During reception of stereo stations the "ST" indicator

is ON.

Canceling Direct Access Tuning

Press the [DIRECT] button on the remote.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Station Preset Memory

Preset Tuning

Putting the station in the memory.

Calling up the stations in the memory.

1 Select the band

Press the [FM+] or [AM–] button.

1 Select the band

Press the [FM+] or [AM–] button.

Select the frequency to put in the memory

Press the [

] or [

] button.

Call up the station

Press the desired [1] — [6] button.

Put the frequency in the memory

Press the desired [1] — [6] button for at least

2 seconds.

The preset number display blinks 1 time.

On each band, 1 station can be put in the

memory on each [1] — [6] button.

Frequency Step Setting

Changing the tuning frequency step.

The original setting is FM band 50 kHz, and AM

band 9 kHz.

Turn the power OFF

Press the [SRC] button for at least 1 second.

Auto Memory Entry

2 Switch the frequency step

While pressing the [1] and [5] button, press

the [SRC] button.

The frequency step changes to FM band 200 kHz,

and AM band 10 kHz.

Putting a station with good reception in the

memory automatically.

Select the band for Auto Memory Entry

Press the [FM+] or [AM–] button.

2 Enter Function mode

Press the [FNC] button for at least 1 second.

"Function" is displayed.

•

When the same operation is repeated, it returns to the

original setting.

When the frequency step is switched, the frequencies

in the memory are deleted.

3 Select the Auto Memory Entry mode

Press the [FM+] or [AM–] button.

Select the "A-Memory" display.

Open Auto Memory Entry

Press the [

] or [

] button for at least 2

seconds.

When 6 stations that can be received are put in

the memory Auto Memory Entry closes.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Cassette player features

�

� ��

��

�

��

ndicator

Repeat indicator

Blank Skip indicator

indicator

Dolby B NR indicator

MTL indicator

Tape counter display

Playing Cassette Tapes

Dolby B NR

Press the [B NR] button.

Each time the button is pressed the Dolby B NR

turns ON or OFF.

When the Cassette Tape is inserted

Press the [SRC] button.

Select the "TAPE" display.

When it’s ON, "B NR On" is displayed.

•

When there’s a Cassette Tape inserted, the

indicator is ON.

Selecting the Tape type

When you want to listen to the reverse side

Press the [

] button.

Press the [MTL] button.

Each time the button is pressed the Tape type

switches as shown below.

Eject the Cassette Tape

Press the [

] button.

Tape type

Display

CrO (Type II), FeCr (Type III), Metal (Type IV)

Normal (Type I)

"MTL On"

"MTL Off"

Fast Forwarding and Rewinding

Fast Forwarding

Press the [FM+] button.

When the [

] button is pressed it releases.

Rewinding

Press the [AM–] button.

When the [

] button is pressed it releases.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

DPSS (Direct Program Search

System)

Blank Skip

Fast forwarding automatically when an

unrecorded portion continues for at least 10

seconds.

Indicating the songs to skip, and Fast Forwarding

or Rewinding.

Press the [B.S] button.

Each time the button is pressed the Blank Skip

turns ON or OFF.

Skipping to a later song

Press the [

] button.

Each time the button is pressed the number of

songs skipped increases.

When it’s ON, "B.S On" is displayed.

Skipping to a previous song

Press the [

] button.

Index Scan

Each time the button is pressed the number of

songs skipped increases.

Playing the first part of each song on the tape you

are listening to and searching for the song you

want to listen to.

Canceling DPSS

Press the [

] button.

1 Start Index Scan

Press the [SCN] button.

"IDX SCAN" is displayed.

•

During the songs first 5 seconds the previous song

may be recognized as the current song.

As many as 9 songs can be skipped.

2 Release it when the song you want to listen

to is played

Press the [SCN] button.

DPSS with the Remote

Designating the song to be skipped with the

remote control number buttons.

Music Repeat

Repeating the present song.

Designate the song to skip

Press number buttons on the remote.

Press the [REP] button.

Each time the button is pressed the Music

Repeat turns ON or OFF.

When it’s ON, "Repeat" is displayed.

Skipping to a later song

Press the [

] button.

Skipping to a previous song

Press the [

] button.

Canceling DPSS

Press the [

] button.

•

During the songs first 5 seconds there may be a times

when the previous track is recognized as the current

track.

As many as 9 songs can be skipped.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/ MP3/ WMA/ External disc control features

�

��

�

��

RDM indicator

Track time

SCN indicator

Track number

REP/D.REP indicator

CH indicator

Disc number

indicator

WMA/MP3 indicator

Playing CD & MP3/WMA

•

The MP3/WMA media that this unit can play are CD-

ROM, CD-R, and CD-RW.

When a CD is inserted

Press the [SRC] button.

Select the "CD" display.

The medium formats must be ISO 9660 Level 1, Level

2, Joliet, or Romeo. The methods and precautions to

be followed for writing MP3/WMA data are covered in

'Notes on playing MP3/WMA' (page 6).

Check that section before creating your MP3/WMA

media.

•

When a CD is inserted, the

The models that can play MP3/WMA are shown

below.

indicator is ON.

KDC-MP4070/KDC-MP4070B

•

During MP3 is playing, the "MP3" indicator is ON.

During WMA is playing, the "WMA" indicator is ON.

Pause and play

Playing External Disc

Press the [

] button.

Each time the button is pressed it pauses and

plays.

Playing discs set in the optional accessory disc

player connected to this unit.

Press the [SRC] button.

Eject the CD

Select the display for the disc player you want.

Display examples:

Press the [

] button.

Display

"CD CH"

"MD CH"

Disc player

CD changer

MD changer

Do not attach an adapter to an 8cm (3 in.) CD.

Inserting an 8cm CD with an adapter into this unit

may cause damage.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Pause and play

Canceling Direct Track/File Search

Press the [

] button.

Each time the button is pressed it pauses and

plays.

Press the [

] button.

Function of disc changers with remote

•

Disc 10 is displayed as "0".

Direct Disc Search

The functions that can be used and the information

that can be displayed will differ depending on the

external disc players being connected.

Doing Disc Search by entering the disc number.

Enter the disc number

Press the number buttons on the remote.

2 Do Disc Search

Press the [DISC+] or [DISC–] button.

Fast Forwarding and Reversing

Fast Forwarding

Canceling Direct Disc Search

Hold down on the [

] button.

Release your finger to play the disc at that point.

Press the [

] button.

Reversing

•

Input "0" to select disc 10.

Hold down on the [

] button.

Release your finger to play the disc at that point.

Track/File/Disc/Folder Repeat

Replaying the song, disc in the Disc changer or

MP3/WMA folder you’re listening to.

Track/File Search

Searching for a song on the disc or in the MP3/

WMA folder.

Press the [REP] button.

Each time the button is pressed the Repeat Play

switches as shown below.

Press the [

] or [

] button.

In CD & External disc source

Repeat play

Track Repeat

Disc Repeat (In Disc Changer)

OFF

Display

"Repeat"

"D-Repeat"

Function of disc changer/ MP3/ WMA

Disc Search/Folder Search

Selecting the disc set in the Disc changer or the

folder recorded on the MP3/WMA media.

In MP3/WMA source

Press the [AM–] or [FM+] button.

Repeat play

File Repeat

Folder Repeat

OFF

Display

"File REP"

"Fold.REP"

Function of remote

Direct Track/File Search

Doing Track/File Search by entering the track/file

number.

Enter the track/file number

Press the number buttons on the remote.

Do Track/File Search

Press the [

] or [

] button.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/ MP3/ WMA/ External disc control features

Function of DPX-MP4070/DPX-MP4070B

Function of MP3/WMA

Scan Play

Playing the first part of each song on the disc

or MP3/WMA folder you are listening to and

searching for the song you want to listen to.

Folder Select

Quickly selecting the folder you want to listen to.

Enter Folder Select mode

Press the [F.SEL] button.

During Select mode the folder information is

displayed as shown below.

1 Start Scan Play

Press the [SCN] button.

"Scan" is displayed.

Release it when the song you want to listen

to is played

Press the [SCN] button.

Folder name display

Displays the current folder name.

KENWOOD

Random Play

Select the folder level

Press the [FM+] or [AM–] button.

With the [FM+] button you move 1 level down

and with the [AM–] button 1 level up.

Play all the songs on the disc or MP3/WMA folder

in random order.

Press the [RDM] button.

Selecting a folder in the same level

Press the [

] or [

] button.

With the [

] button you move to the previous

folder, and with the [

] button to the next

folder.

Each time the button is pressed Random Play

turns ON or OFF.

When it’s ON, "Random" is displayed.

•

When the [¢] button is pressed, the next song

select starts.

Returning to the top level

Press the [3] button.

Decide the folder to play

Press the [

] button.

The Folder Select mode releases, and the MP3/

WMA in the folder being displayed is played.

Function of disc changer

Magazine Random Play

Play the songs on all the discs in the disc changer

in random order.

•

The methods for moving to other folders in the folder

select mode are different from those in the folder

search mode.

Press the [M.RDM] button.

Each time the button is pressed the Magazine

Random Play turns ON or OFF.

See 'Notes on playing MP3/WMA' (page 6) for details.

When it’s ON, "M-Random" is displayed.

Canceling the Folder Select mode

Press the [F.SEL] button.

•

When the [

] button is pressed, the next song

select starts.

Text/Title Scroll

Scrolling the displayed CD text, MP3/WMA text,

or MD title.

Press the [SCRL] button.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Function Set

��

� � �

��

�

Function Set

4 Exit Function Set mode

Press the [FNC] button.

Setting during operation beep sound etc.

functions.

The Function Set basic operation method is

explained here. The reference for the Function

items and their setting content is after this

operation explanation.

•

When other items that are applicable to the basic

operation method above are displayed afterwards

their setting content chart is entered. (Normally the

uppermost setting in the chart is the original setting.)

Also, the explanation for items that aren’t applicable

are entered step by step.

1 Enter Function Set mode

Press the [FNC] button for at least 1 second.

"Function" is displayed.

Select the Function Set item

Press the [FM+] or [AM–] button.

Example: When you want to set the beep sound

select the "BEEP" display.

3 Set the Function Set item

Press the [

] or [

] button.

Example: When "BEEP" is selected, each time the

button is pressed it switches "BEEP On"

or "BEEP Off". Select 1 of them as the

setting.

You can continue by returning to step 2 and

setting other items.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Function Set

In Standby mode

Illumination Color Mode

Switching preout

Setting the Illumination Color Mode of your

display.

Switching the preout between the rear and

subwoofer. (In subwoofer it outputs without

effect from the fader control.)

Display

Setting

Display

"SWPRE R"

"SWPRE SW"

Setting

Rear preout.

Subwoofer preout.

The color of your display changes from one

color to another during volume adjustment

and during Attenuator being ON.

"COL Sync"

"COL Fix"

Fix the color set.

In Standby mode

Opening Demonstration

Contrast Adjustment

Setting the Demonstration when Power is turned

ON.

Adjusting the display contrast.

Display and Setting

"CONT 1"

Display

Setting

Demonstration is carried out when Power is

turned ON.

"Open On"

"CONT 6" (Original setting)

"CONT 11"

Demonstration is not carried out when Power

is turned ON.

"Open Off"

In Standby mode

Equalizer mode

In Standby mode

Setting the method of adjusting Equalizer types.

Touch Sensor Tone

Setting the operation check sound (beep sound)

ON/OFF.

Display

Setting

The effects of Equalizer type can be adjusted

among 3 levels.

"EQ EASY"

Display

Setting

Equalizer types can be adjusted by Bass,

Middle, and Treble.

"EQ PRO"

"BEEP On"

"BEEP Off"

Beep is heard.

Beep canceled.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

In Standby mode

Security Code

Navigation Mute

Because authorization by the Security Code is

required when it’s removed from the vehicle,

personalizing this unit is by using the Security

Code is a help in preventing theft.

Mute the audio sound during Voice Guidance of

navigation.

Display

Setting

"NavM Off"

"NavM On"

Does not mute the sound.

Mutes the sound.

•

When the Security Code function is activated, the code

can’t be changed and the function can’t be released.

Note, the Security Code can be set as the 4 digit number

of your choice.

In Standby mode

Select the Security Code mode

Press the [FM+] or [AM–] button.

Select the "CODESTBY" display.

TEL Mute

You can set to mute the sound when a call comes

in.

Enter Security Code mode

Press the [COL] button for at least 2 seconds.

When "WRITE" is displayed, "CODE ****" is

displayed.

Display

"TelM Off"

"TelM On"

Setting

Does not mute the sound.

Mutes the sound.

3 Enter the Security Code

Press the [1] — [4] button.

Example: If the Security Code is "3510".

In Standby mode

Step

Button

[1]

[2]

[3]

[4]

Times pressed

Display

"3"

"5"

"1"

"0"

Built-in Auxiliary input Setting

Set the Built-in Auxiliary Input function.

Display

Setting

"AUX Off"

"AUX On"

When selecting the source there’s no Auxiliary Input.

When selecting the source there’s Auxiliary Input.

Confirm the Security Code

Press the [COL] button.

When "WRITE" is displayed, "1 CODE **** " is

displayed.

In Standby mode

Do the steps 3 through 4, and reenter the

Security Code.

Built-in Amp Mute Setting

Toggles ON or OFF the mute control on the built-

The Security Code function activates.

in amplifier.

Turning ON this control enhances the preout

quality.

•

When a Code different from step 3 is entered, repeat

from step 3.

Display

"AmpM Off"

"AmpM On"

Setting

The built-in amplifier activates.

The built-in amplifier deactivates.

Press the Reset button and when it’s removed

from the battery power source

Turn the power ON.

Do the steps 3 through 4, and enter the

Security Code.

"CODE OK!" is displayed.

The unit can be used.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Function Set

In Standby mode

In Tuner mode

Security Indicator

Tuning Mode

A red indicator will blink on the unit after the ACC

is set to OFF, warning potential thieves.

Sets the tuning mode.

Tuning mode

Auto seek

Display

"Auto 1"

Operation

Automatic search for a station.

Search in order of the stations

in the Preset memory.

Display

"S.I Off"

"S.I On"

Setting

LED OFF.

LED flashes.

Preset station seek "Auto 2"

Manual

"Manual"

Normal manual tuning control.

Function of DPX-MP4070/DPX-MP4070B

In Standby mode

In FM reception

CD Read Setting

Monaural Reception

When there is a problem on playing a CD with

special format, this setting play the CD by force.

Noise can be reduced when stereo broadcasts are

received as monaural.

Display

Setting

Display

Setting

"CD READ1"

"CD READ2"

Play CD and MP3/WMA.

Play CD by force.

"MONO Off"

"MONO On"

The monaural reception is OFF.

The monaural reception is ON.

•

Setting "CD READ 2" cannot play MP3/WMA.

Some music CDs may not be played back even in the

"CD READ 2" mode.

In Tuner mode

Auto Memory Entry

For the operation method refer to 'Auto Memory

Entry' (page 17).

In CD/MP3/WMA/External disc control mode

Text Scroll

Setting the displayed text scroll.

Display

Setting

"SCL Auto"

"SCL Manu"

Repeats scroll.

Scrolls when the display changes.

•

The text scrolled is shown below.

- CD text

- Folder name/ File name/ Song title/ Artist name/

Album name

- MD title

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations of remote

��

�

��

Not Used

��

Loading and Replacing the battery

Basic operations

Use two "AA"-size batteries.

[VOL.] buttons

Slide the cover while pressing downwards to

remove it as illustrated.

Adjusting the volume.

[SRC] button

Each time the button is pressed the source

switches.

Insert the batteries with the + and – poles aligned

properly, following the illustration inside the case.

For the source switching order refer to 'Selecting

the Source' (page 9).

[ATT] button

Turning the volume down quickly.

When it is pressed again it returns to the previous

level.

2WARNING

•

Store unused batteries out of the reach of children.

Contact a doctor immediately if the battery is

accidentally swallowed.

Do not set the remote on hot places such as above

the dashboard.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations of remote

In Tuner source

In Disc source

[FM]/ [AM] buttons

Select the band.

[

]/ [

] buttons

Doing track/file forward and backward.

Each time the [FM] button is pressed it switches

between the FM1, FM2, and FM3 bands.

[DISC+]/ [DISC–] buttons

Doing disc/folder forward and backward.

[

]/ [

] buttons

[

] button

Each time the button is pressed the song pauses

and plays.

Tune up or down band.

[0] — [9] buttons

Press buttons [1] — [6] to recall preset stations.

[0] — [9] buttons

[DIRECT] button

Enters and cancels the 'Direct Access Tuning'

(page 16) mode.

When in 'Direct Track/File Search' (page 21) and

'Direct Disc Search' (page 21), enter the track/file/

disc number.

In Cassette tape source

[4]/ [¢] buttons

Do 'DPSS (Direct Program Search System)' (page

19).

[

] button

Plays the reverse side of the tape.

[FM ] button

Fast forwards the tape.

When the [

] button is pressed it releases.

[AM] button

Rewinds the tape.

When the [

] button is pressed it can be

released.

[0] — [9] buttons

When in 'DPSS with the Remote' (page 19) enter

the number of songs.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories/ Installation Procedure

Accessories

Installation Procedure

1. To prevent a short circuit, remove the key from

the ignition and disconnect the - battery.

2. Make the proper input and output wire

connections for each unit.

..........1

3. Connect the speaker wires of the wiring harness.

4. Connect the wiring harness wires in the

following order: ground, battery, ignition.

5. Connect the wiring harness connector to the

unit.

..........1

..........6

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

2WARNING

If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always connect those

wires to the power source running through the fuse box.

•

If your car’s ignition does not have an ACC position,

connect the ignition wires to a power source that can be

turned on and off with the ignition key. If you connect

the ignition wire to a power source with a constant

voltage supply, as with battery wires, the battery may die.

If the console has a lid, make sure to install the unit so

that the faceplate will not hit the lid when closing and

opening.

If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with

one with the same rating.

Insulate unconnected wires with vinyl tape or other

similar material. To prevent a short circuit, do not remove

the caps on the ends of the unconnected wires or the

terminals.

•

Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail

to work if you share the - wires or ground them to any

metal part in the car.

When only two speakers are being connected to the

system, connect the connectors either to both the front

output terminals or to both the rear output terminals

(do not mix front and rear). For example, if you connect

the + connector of the left speaker to a front output

terminal, do not connect the - connector to a rear

output terminal

•

After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

Mount the unit so that the mounting angle is 30° or less.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Wires to Terminals

AUX left input (White)

AUX right input (Red)

Rear left output (White)/

Subwoofer left output (White)

Front left output (White)

Front right output (Red)

Rear right output (Red)/

Subwoofer right output (Red)

M4�8mmMAX

FM/AM antenna input

KENWOOD disc changer control input

To connect the Disc changer, consult

your Disc changer manual.

Wiring harness

Fuse (10 A)

(Accessory1)

If no connections are made, do not

let the wire come out from the tab.

Depending on what antenna you are using, connect either to

the control terminal of the motor antenna, or to the power

terminal for the booster amplifier of the film-type antenna.

ANT. CONT

Motor antenna control wire (Blue)

When using the optional power amplifier, connect to its

power control terminal.

P.CONT

Power control wire (Blue/White)

Connect to the terminal that is grounded when either the

telephone rings or during conversation. To connect the

KENWOOD navigation system, consult your navigation

manual.

MUTE

TEL mute wire (Brown)

To car light control switch

ILLUMI

Dimmer control wire (Orange / White)

To "EXT.AMP.CONT." terminal of the amplifier having the

external amp control function.

EXT.CONT.

External amplifier control wire

(Pink / Black)

White/Black

White

To front left speaker

To front right speaker

Gray/Black

Gray

Green/Black

Green

To rear left speaker

Purple/Black

Purple

To rear right speaker

Ignition key

Car fuse box

switch

Ignition wire (Red)

ACC

Car fuse box

(Main fuse)

Battery wire (Yellow)

Ground wire (Black) - (To car chassis)

Battery

�

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

When performing a check of the CD operation prior

to installation, place this unit in a horizontal position

and perform a loading/eject of the CD.

Installation

Install onto the car bracket using the supplied

screws (M5 × 6 mm, M5 × 7 mm). The holes of the

car bracket to use will differ depending on the car

model.

When a ground wire is included in the wiring kit (which

is sold separately), fasten the ground wire with the

binding screw located on the rear panel of this unit.

Screw (M4× 8)

(commercially available)

Accessory3

(M5 × 6 mm)

or Accessory4

(M5 × 7 mm)

Accessory2

(Only for NISSAN car)

•

During installation, do not use any screws except for

those provided. The use of different screws might result

in damage to the main unit.

Damage may occur if a screwdriver or similar tool is used

with excessive force during the installations.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

What might seem to be a malfunction in your unit

may just be the result of slight misoperation or

miswiring. Before calling service, first check the

following table for possible problems.

? No sound can be heard, or the volume is low.



The fader or balance settings are set all the way to

one side.



Center the fader and balance settings.



The input/output wires or wiring harness are

connected incorrectly.



Reconnect the input/output wires or the

wiring harness correctly. See the section on

'Connecting Wires to Terminals'.

General

? The power does not turn ON.



The fuse has blown.



The cassette tape is bad.



After checking for short circuits in the wires,

replace the fuse with one with the same

rating.

Try playing another cassette tape. If works fine,

the first tape was bad.

The values of Volume offset are low.





Speaker cable touches on chassis etc.

Turn up the Volume offset, referring to the

section on 'Audio Control' (page 10).



Wire or insulate the speaker cable properly

and press the reset button.

The 'Built-in Amp Mute Setting' (page 25) is ON.

Turn it OFF.



There’s a source you can’t switch.



There’s no media inserted.

The sound quality is poor or distorted.



Set the media you want to listen to. If there’s

no media in this unit, you can’t switch to each

source.



One of the speaker wires is being pinched by a

screw in the car.



Check the speaker wiring.

The tape head is dirty.

Clean the tape head.

The speakers are not wired correctly.



The Disc changer isn’t connected.





Connect the Disc changer. If the Disc changer

isn’t connected to it’s input terminal, You can’t

switch to an external disc source.



Reconnect the speaker wires so that each

output terminal is connected to a different

speaker.

The memory is erased when the ignition is

turned OFF.



The ignition and battery wire are incorrectly

connected.

? The Touch Sensor Tone doesn’t sound.

The preout jack is being used.





Connect the wire correctly, referring to the

section on 'Connecting Wires to Terminals'.



The Touch Sensor Tone can’t be output from

the preout jack.

? The TEL mute function does not work.

? The Dimmer function doesn’t work.

The Dimmer wire isn’t connected correctly.

Check the Dimmer wire connection.



The TEL mute wire is not connected properly.





Connect the wire correctly, referring to the

section on 'Connecting Wires to Terminals'.





The 'TEL Mute' (page 25) is OFF.

Turn it ON.

Tuner source



? Radio reception is poor.

? The TEL mute function turns ON even though the

TEL mute wire is not connected.



The car antenna is not extended.



Pull the antenna out all the way.



The TEL mute wire is touching a metal part of the



The antenna control wire is not connected.

car.



Connect the wire correctly, referring to the

section on 'Connecting Wires to Terminals'.

Pull the TEL mute wire away from the metal

part of the car.

The desired frequency can’t be entered with the

Direct Access Tuning.



A station that can’t be received is being entered.



Enter a station that can be received.



You’re trying to enter a frequency with a 0.01 MHz

unit.



What can be designated in the FM band is to

0.1 MHz.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Cassette tape source

Disc source

Can’t remove tape.

"AUX EXT" is displayed without achieving



The cause is that more than 10 minutes has

elapsed since the vehicle ACC switch was turned

OFF.

External disc control mode.



Unsupported disc changer is connected.



Use the disc changer mentioned in the

'About CD players/disc changers connected

to this unit' (page 4) of the section on 'Safety

precautions'.



The tape can only be removed within 10

minutes of the ACC switch being turned OFF.

If more than 10 minutes has elapsed, turn

the ACC switch ON again and press the Eject

button.

? The specified disc does not play, but another one

plays instead.

? The DPSS, Tape Advance and Music Repeat don’t

operate correctly.



The specified CD is quite dirty.



Clean the CD.



The space between the songs on the tape can’t be



The disc is loaded in a different slot from that

specified.

recognized because it’s too short.



Have at least 4 seconds between songs.



Eject the disc magazine and check the

number for the specified disc.



The space between songs can’t be recognized

because there’s too much noise between songs.





The disc is severely scratched.

 Try another disc instead.

Reduce the noise between songs.

? The blank skip doesn’t work.

? A CD ejects as soon as it is loaded.

The CD is quite dirty.



Because noise is too loud, the non-recorded part

can’t be recognized.





Clean the CD, referring to the CD cleaning of

the section on 'About CDs' (page 8).



Reduce the noise between songs.

Blank Skip functions at places that are recorded.

Can’t remove disc.

The cause is that more than 10 minutes has



Because the recording level is low, it’s recognized

as not recorded.



elapsed since the vehicle ACC switch was turned

OFF.



Turn Blank Skip OFF.



The disc can only be removed within 10

minutes of the ACC switch being turned OFF.

If more than 10 minutes has elapsed, turn

the ACC switch ON again and press the Eject

button.

? 'Music Repeat' (page 19) is cancelled arbitrarily.



The power was turned OFF or a source selection

or other operation was performed.



Music repeat is cancelled when the power

is turned OFF or a source selection or other

operation is performed.

? The disc won’t insert.

There’s already another disc inserted.

Press the [0] button and remove the disc.





? Direct Search can’t be done.

Another function is ON.

Turn Random Play or other functions OFF.





Track Search can’t be done.

For the discs/folders first or last song.





For each disc/folder, Track Search can’t be

done in the backward direction for the first

song or in the forward direction for the last

song.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

MP3/WMA source

The messages shown below display your

systems condition.

Cannot play an MP3/WMA.



The media is scratched or dirty.

EJECT:

No disc magazine has been loaded in

the changer. The disc magazine is not

completely loaded.



Clean the media, referring to the CD cleaning

of the section on 'About CDs' (page 8).

 Load the disc magazine properly.

No CD in the unit.

 Insert the CD.

? The sound skips when an MP3/WMA is being

played.



The media is scratched or dirty.



Clean the media, referring to the CD cleaning

of the section on 'About CDs' (page 8).

No Disc:

Error 04:

Error 05:

No disc has been loaded in the disc

magazine.

 Load a disc into the disc magazine.



The recording condition is bad.

Record the media again or use another media.



The CD is quite dirty. The CD is upside-

down. The CD is scratched a lot.

 Clean the CD and load it correctly.

? The MP3/WMA track time isn’t displayed

correctly.



---



The CD is upside-down.

 Load the CD correctly.

There are times when it isn’t displayed

correctly according to the MP3/WMA

recording conditions.

Blank:

Nothing has been recorded on the MD.

If the following situations, consult your

nearest service center:

No Track:

No tracks are recorded on the MD,

although it has a title.

Even though the disc changer is connected, the

Disc Changer source is not ON, with "AUX EXT"

showing in the display during the Changer Mode.

Error 77:

Error 99:

The unit is malfunctioning for some reason.

 Press the reset button on the unit. If

the "Error-77" code does not disappear,

consult your nearest service center.

Something is wrong with the disc

magazine. Or the unit is malfunctioning for

some reason.

 Check the disc magazine. And then

press the reset button on the unit. If

the "Error 99" code does not disappear,

consult your nearest service center.

Hold:

The protective circuit in the unit activates

when the temperature inside the

automatic disc changer exceeds 60°C

(140°F), stopping all operation.

 Cool down the unit by opening

the windows or turning on the air

conditioner. As the temperature falls

below 60°C (140°F), the disc will start

playing again.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

No Name:

Load:

Attempted to display DNPS during the CD

play having no disc names preset.

Discs are being exchanged in the Disc

changer.

Reading:

The unit is reading the data on the disc.

(Blink):

The CD player section is not operating

properly.

 Reinsert the CD. If the CD cannot be

ejected or the display continues to flash

even when the CD has been properly

reinserted, please switch off the power

and consult your nearest service center.

(Blink):

The tape player section is not operating

properly.

 Reinsert the Tape. If the tape cannot be

ejected or the display continues to flash

even when the tape has been properly

reinserted, please switch off the power

and consult your nearest service center.

N/A File:

A MP3/WMA is played with a format that

this unit can’t support.



----

Protect:

A copy-protected file is played.



----

English

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Specifications subject to change without notice.

FM tuner section

Frequency range

50 kHz space : 87.5 MHz – 108.0 MHz

200 kHz space : 87.9 MHz – 107.9 MHz

Usable sensitivity (S/N = 30dB)

: 9.3dBf (0.8 µV/75 Ω)

Quieting Sensitivity (S/N = 50dB)

: 15.2dBf (1.6 µV/75 Ω)

Frequency response (±3.0 dB)

: 30 Hz – 15 kHz

Signal to Noise ratio (MONO)

: 70 dB

Selectivity (±400 kHz)

: ≥ 80 dB

Total harmonic distortion (1 kHz)

: 0.01 %

Signal to Noise ratio

: 100 dB (1 kHz)

Dynamic range

: 93 dB

Channel separation

: 85 dB

MP3 Decode (KDC-MP4070/KDC-MP4070B)

: Compliant with MPEG-1/2 Audio Layer-3

WMA decode (KDC-MP4070/KDC-MP4070B)

: Compliant with Windows Media Audio

Audio section

Maximum output power

: 50 W × 4

Stereo separation (1 kHz)

: 30 dB

Full bandwidth power (at less than 1% THD)

AM tuner section

Frequency range

9 kHz space : 531 kHz – 1611 kHz

10 kHz space : 530 kHz – 1700 kHz

Usable sensitivity (S/N = 20dB)

: 28 dBµV (25 µV)

: 22 W × 4

Preout level / Load

: 1800mV/10kΩ

Preout impedance

: ≤ 600 Ω

Auxiliary input

Frequency response (±1 dB)

: 20 Hz – 20 kHz

Input Maximum Voltage

: 1200 mV

Cassette player section

Tape speed

: 4.76 cm/sec.

Wow & Flutter (WRMS)

: 0.1 %

Frequency response (70 µs)

: 40 Hz – 20 kHz (±3 dB)

Input Impedance

: 100 kΩ

Separation (1 kHz)

: 35 dB

General

Operating voltage (11 – 16V allowable)

: 14.4 V

Signal to Noise ratio

Dolby NR Off : 50 dB

Current consumption

: 10 A

Dolby B NR On : 60 dB

Installation Size (W x H x D)

: 178 × 100 × 155 mm

Weight

: 2.3 kg

CD player section

Laser diode

: GaAlAs

Digital filter (D/A)

: 8 Times Over Sampling

D/A Converter

: 1 Bit

Spindle speed

: 500 – 200 rpm (CLV)

Wow & Flutter

: Below Measurable Limit

Frequency response (±1 dB)

: 10 Hz – 20 kHz

English

Download from Www.Somanuals.com. All Manuals Search And Download.

安全注意事項

CD/�MP3/�WMA/�外部光盤控制特性

警告

注意

註

播放�CD�和�MP3/WMA

播放外部光盤

快進和快退

音軌 / 檔案搜索

光盤搜索 / 檔案夾搜索

直接音軌 / 檔案搜索

直接光盤搜索

音軌 / 檔案 / 光盤 / 檔案夾反復

掃描播放

隨機播放

換片機隨機播放

檔案夾選擇

註

關於磁帶

關於播放�MP3/WMA�的注意事項

關於�CD

總體特性

文本 / 標題滾動

電源

選擇音源

功能設定

音量

功能設定

衰減器

音響控制

照明顏色模式

對比度調節

按鍵音調

切換預輸出

開機演示

低音揚聲器輸出

電話消音

SRS�WOW 選擇

SRS�WOW 控制

均衡器控制

均衡器模式

保安代碼

均衡器類型的 EASY （簡便）調整

均衡器類型的 PRO （專門）調整

均衡器類型調整的預設記憶

電影選擇

切換顯示

照明顏色選擇

用戶照明顏色設定

調節時鐘

電台 / 光盤命名（SNPS/DNPS）

輔助輸入顯示設定

導航靜音

電話消音

內置輔助輸入設定

內置放大器消音設定

防盜警告燈

CD�讀取設定

調諧模式

單聲道接收

自動記憶輸入

文本滾動

調諧器特性

遙控器的基本操作

附件 / 安裝程序

連接

調諧

直接調諧

電台預設記憶

自動記憶輸入

預設調諧

安裝

頻率間距設定

錄音座特性

故障檢修

規格

播放磁帶

快進和快退

Dolby�B�NR

選擇磁帶型式

DPSS （Direct�Program�Search�System）

遙控器的�DPSS

空白跳越

索引掃描

音樂反復

38 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

安全注意事項

2 警告

2 注意

為了防止受傷和火災請遵守下列注意事項：

．

請將面板切實按入裝置直至鎖住為止，以免遇到

碰撞等衝擊時飛出。

為了防止裝置發生故障，請遵守下列注意事項，

正確操作和使用：

．

請以�-�接地線的�12V�電源向本裝置供電。

．

請勿打開頂部和底部的蓋子。

．當延長點火線、蓄電池導線和接地導線時，請使

用車輛用導線或�0.75mm²（AWG18）以上的導線，

以防止導線劣化和被覆面的損傷。

．

請勿將本裝置安裝在曝露於直射陽光、高溫或高

濕、水可能飛濺的或有灰塵的地方。

．

為了防止短路等事故，請勿將金屬物品（硬幣、

工具等）掉落在裝置中。

．

更換保險絲時，請更換規定容量相同的保險絲，

如使用不同容量的保險絲，可能會造成裝置的故

障。

．

萬一裝置冒煙或有異味時，請立即關閉電源，並

與�KENWOOD�經銷商洽談。

．

更換保險絲時，為了防止短路事故，請先拔下電

源線束來再進行更換。

．

請注意不要使手指夾在面板和裝置之間。

．

請不要使裝置掉落、或受到強烈碰撞。

．

安裝時，請務必使用所附的螺絲。如使用其他的

螺絲，可能會造成裝置的故障。

由於本產品使用了玻璃零部件，如破碎將有造成

受傷的危險。

．

如因碰撞等液晶破損時，請不要觸摸液晶液，以

免發生生命危險。

液晶液如沾附在身體或衣服上時，請立即以肥皂

等清洗乾淨。

中文 39

Download from Www.Somanuals.com. All Manuals Search And Download.

安全注意事項

關於與本機連接的�CD�播放機 / 光盤換片機

本機可以連接於� 1998� 年或者以後製造的�

KENWOOD�光盤換片機 /CD�播放機。

註

．

安裝有困難時，請與�KENWOOD�經銷商洽談。

．

如果本機發生誤運轉時，請先按下復位按鈕。如

按下復位按鈕，裝置即復原為初始狀態。如果仍

不能恢復正常時，請與�KENWOOD�經銷商洽談。

有關可以連接的光盤換片機 /CD� 播放機的型號，請

參照產品樣本，或者與當地的� KENWOOD� 經銷商

洽詢。

．

當光盤換片機發生誤運轉時，請按下複位按鈕。

即復原為正常操作狀態。

請注意，於�1997�年或者以前製造的�KENWOOD�光

盤換片機 /CD� 播放機、以及由其他廠家製造的光盤

換片機無法與本機連接。

連接不兼容的裝置可能造成損壞。

對於適用的� KENWOOD� 光盤換片機 /CD� 播放機，

請將�O-N�開關設定為�"N"。

根據所連接的裝置型號，可以使用的功能和能夠顯

示的資訊將有所不同。

如不遵守上述注意事項，會造成本機、 CD� 換片機的故

障。

復位按鈕

．

當溫度低於�41 ℉ （5℃）時， LCD�顯示的字母

將難以辨認。

．

出現在本說明書中的顯示屏幕和操作盤的插圖是

用於更清楚地說明如何進行控制的說明例子，因

此，出現在插圖中的顯示屏幕可能與實際出現在

裝置上的顯示不同，並且有些顯示屏幕的插圖可

能在實際操作中無法實現。

結露

因天寒冷使用取暖器等之後，有時裝置內部會結露

（水滴）。在這種情況下，不能播放光盤，應將光

盤取出，放置以去除露水。如果經過幾個小時仍不

能正常運轉�，請與�KENWOOD�經銷商洽談。

40 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

註

關於磁帶

裝置的保養

如果本機的面板被弄髒，請使用硅布等乾燥的軟布

擦拭清潔。

清潔磁頭

由於磁頭不清潔，當在播放磁帶時產生雜音，或者

音質變差時，請清潔磁頭。

如果面板很髒，請蘸中性清潔劑擦拭污垢，然後擦

去清潔劑。

關於磁帶

．對本機直接噴洒清潔劑將可能使得機械部件受到影響。

使用硬質的布或者使用諸如稀釋劑或酒精等揮發性溶劑

擦拭面板將劃傷表面或者將字符擦掉。

．請捲緊磁帶，消除鬆弛。

．磁帶的標籤鬆動時，請重新粘貼。

．請不要使用變形的磁帶。

．請不要將磁帶放在儀錶板上等高溫位置。

．請不要使用 100 分鐘以上的磁帶。

CD�槽的保養

CD� 槽易於沾附灰塵，請經常清理。如在沾附灰塵

的情況下插入�CD，會使�CD�受到損傷。

使用激光的產品標誌

（部分地區除外）

CLASS 1

LASER PRODUCT

貼附在機架或外盒上的標記，是表示該產品使用了

分類為� CLASS1� 激光的標誌，表明本裝置利用了最

弱級的激光束，並無向裝置外輻射的危險。

WOW、 SRS�及

商標。

�標誌是�SRS�Labs,�Inc.�的註冊

本產品已獲�SRS�Labs,�Inc.�授權使用�WOW�技術。

經杜比實驗室授權生產。

" 杜比 "，"Dolby"�和雙 D 標志是杜比實驗室的商標。

中文 41

Download from Www.Somanuals.com. All Manuals Search And Download.

．

檔案夾名稱的最多字符數量：64 （Joliet；最多

可顯示�32�個字符）

．

傳送位元率為�

．

取樣頻率

MP3：8�—320�kbps

WMA：48�—192�kbps

．

Joliet （64�字符；最多可顯示�32�個字符）

關於播放�MP3/WMA�的注意事項�(DPX-MP4070/DPX-MP4070B)

但是可以使用的記錄� MP3/WMA� 檔案的媒體以及格

式具有若干限制。記錄� MP3/WMA� 檔案時，請注

意以下事項。

輸入�ID3�標籤

可顯示的�ID3�標簽為�ID3�的版本�1.x.。有關字符代

碼，請參照代碼表。

可以使用的媒體

本機可以使用的記錄� MP3/WMA� 檔案的媒體為

CD-ROM、 CD-R�以及�CD-RW。

使用� CD-RW� 時，請採用全格式化而不是快速格式

化，避免發生故障。

可以使用的媒體格式

本機可以使用以下媒體格式。用於檔案和檔案夾名

稱的最多字符數量（包括定義符� "."� 和� 3� 個擴展名

字符）標明在括號中。

．

ISO�9660�1 級（12�字符）

．

ISO�9660�2 級（31�字符）

輸入檔案名稱和檔案夾名稱

可以輸入和顯示的檔案名稱和檔案夾名稱僅限代碼

表中的字符。如果輸入了其他字符，檔案名稱和檔

案夾名稱將無法正確顯示。由於使用不同的� CD� 記

錄器，也可能均無法正確顯示。

本機僅能夠識別和播放具備� MP3/WMA� 擴展名

（.MP3/.WMA）的�MP3/WMA�檔案。

．

Romeo （128�字符；最多可顯示�64�個字符）

．長檔案名稱（200�字符；最多可顯示�64�個字符）

有關可顯示字符一覽表，請參照記錄軟體使用說明

書以及以下的�' 輸入檔案名稱和檔案夾名稱 '�部分。

．對於使用代碼表以外的字符輸入名稱的檔案，有時可能

無法正常播放。

本機可以重新製作的媒體具有下列限制：

．

目錄的最多階層數量：8

．

每個檔案夾的最多檔案數量：255�

．

檔案夾的最多數量：50�

向媒體記錄檔案

放入了記錄有�MP3/WMA�資料的媒體時，本機將檢

查該媒體內的所有檔案。因此，如果該媒體含有較

多的檔案夾或者非� MP3/WMA� 檔案，到開始播放�

MP3/WMA�為止將花費較長的時間。

．

檔案和檔案夾的最多合計數量：512�

使用除了上述以外的格式進行� MP3/WMA� 記錄可能

無法正常播放，並且其檔案名稱或者檔案夾名稱無

法正確顯示。

此外，當本機移動至下一個�MP3/WMA 檔案時，可

能需要花費一些時間，或者檔案搜索以及檔案夾搜

索可能無法順利完成。

MP3/WMA�編碼器和�CD�記錄器的設定

使用�WMA�編碼器將音頻資料壓縮成為�WMA�資料

時，請按照以下設定。

播放這種媒體可能產生巨大噪音損壞揚聲器。

請不要試圖以附加� MP3/WMA� 擴展名的方法播放非�

MP3/WMA�檔案。

如果附加了� MP3/WMA� 擴展名，本機將對於非�

MP3/WMA�檔案錯誤地識別為�MP3/WMA�資料。

不得試圖播放含有非�MP3/WMA�檔案的媒體。

MP3：8,�11.025,�12,�16,�22.05,�24,�32,�44.1,�48�kHz

WMA：32,�44.1,�48�kHz

當使用�CD�記錄器記錄�MP3/WMA�至最大光盤容量

時，請進行禁止追加的設定。當對空光盤一次記錄

至最大容量時，請進行�"Disc�at�Once"�的設定。

．如果使用�Windows�Media�Player�9�以上版本的部分功能，

有時可能無法正常播放。

42 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3/WMA�的播放順序

在當前播放檔案 ¡$、進行檔案搜索時…

當選擇進行播放、檔案夾搜索、檔案搜索、或者檔

案夾選擇時，檔案和檔案夾按照由� CD� 記錄器記錄

的順序存取。

（當前的檔案：¡$）

按鈕的操作

因此，有時預期的播放順序與實際播放的順序不一

致。

檔案的開始 ¡$  ¡#

¡%  ¡&

按鈕

雖然根據� CD� 記錄器而有所不同，但是可以向諸如�

CD-R�的媒體使用以類似�"01"�至�"99"�的播放順序號

碼開始的檔案名稱，或許能夠設定播放 MP3/WMA�

的順序。

在當前播放檔案 ¡$、進行檔案夾搜索時…

（當前的檔案：4）

按鈕的操作

例如，具有下列檔案夾 / 檔案分層結構的媒體將按

照如下所示的檔案夾搜索、檔案搜索或者檔案夾選

擇進行。

AM�按鈕

FM�按鈕

3  2  1  8

5  6  7  8  1

媒體的檔案夾 / 檔案分層結構例

在當前播放檔案� ¡$、選擇了檔案夾選擇來進行

檔案夾之間移動時…

檔案夾

�

檔案

（當前的檔案：4）

按鈕的操作

根

��

�按鈕

AM�按鈕

FM�按鈕

階層�5

階層�1

階層�3

�

階層�4

階層�2

中文 43

Download from Www.Somanuals.com. All Manuals Search And Download.

關於�CD

CD�的使用

．

手持�CD�時，請不要觸摸�CD�的記錄面。

取出�CD�的方法

將�CD�從本機中取出時，請向水平方向拉出。

無法使用的�CD

．

無法使用圓形以外的�CD。

．

CD-R�以及�CD-RW�與通常的音樂�CD�相比，是

容易受到損傷的媒體。請在使用之前，閱讀在�

CD-R�以及�CD-RW�包裝上等說明的注意事項。

無法使用記錄面著色的�CD�以及骯髒的�CD。

．

請勿向�CD�粘貼膠帶等。

．

本機僅能夠播放具備下列標誌�

CD。

�的�

並且請不要使用粘貼了膠帶的�CD。

對於沒有這些標誌的 CD，可能無法正常播放。

使用新的�CD�時

當� CD� 的中心孔以及外側圓周部位有� " 毛刺 "� 時，

請使用圓珠筆等將毛刺去除，然後再使用。

．

沒有進行過最終處理的�CD-R�以及�CD-RW�無法

播放。（有關最終處理的詳細內容，請參照所使

用的�CD-R/CD-RW�記錄器的使用說明書。）

CD�的保管

．

請勿將�CD�放置在日光直射之處（座位以及儀錶

板上）等溫度較高的地方。

毛刺

．

請將�CD�放入盒內保管。

毛刺

關於�CD�用附件

請不要使用光盤用附件。

CD�的保養

請從�CD�的中心向外側擦拭。

44 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

總體特性

�

� � �

��

ATT�指示燈

電源

音量

接通電源

按下�[SRC]�按鈕。

昇高音量

按下�[

]�按鈕。

降低音量

按下�[

∞

]�按鈕。

切斷電源

按下�[SRC]�按鈕�1 秒鐘以上。

衰減器

選擇音源

快速降低音量。

按下�[SRC]�按鈕。

按下�[ATT]�按鈕。

所需的音源

顯示

每次按下按鈕，衰減器切換成為接通或者切斷。

接通時， "ATT"�指示燈閃爍。

調諧器

"TUNER"

"TAPE"

"CD"

磁帶

外部光盤（可選附件）

輔助輸入

"CD�CH"

"AUX"

待機（僅有照明模式）

"STANDBY"

中文 45

Download from Www.Somanuals.com. All Manuals Search And Download.

SRS�WOW

顯示

． *

²�

- 有的放大器型號可以設定為從平坦至＋

��18dB，有的型號可以設定為從平坦至＋ 12dB。

� 當連接了衹能設定至＋ 12dB 的放大器時，即

��使選擇了�"Amp�Bass�+18"，放大器也無法正常

��運行。

． WOW：

． *

¹�

當� ' 低音揚聲器輸出 ' （第 46 頁）設定為�

"SubW�On"�時，可以控制該項目。

．音量偏置：對各個音源的音量可以進行與基本音

總體特性

音響控制

電話消音

當電話打入時，音響系統將自動消音。

^{進入音響控制模式}

按下�[AUD]�按鈕�1�秒鐘以上。

顯示�"AUD�mode"。

當電話打入時

顯示�"CALL"。

音響系統暫停。

^{選擇需要調節的音響項目}

按下�[FM+]�或者�[AM ]�按鈕。

每次按下按鈕，可調節的項目按照以下切換。

在打電話時播放音響

按下�[SRC]�按鈕。

"CALL"�顯示消失，音響系統恢復接通。

3 ^{調節音響項目}

按下�[

]�或者�[

]�按鈕。

電話結束時

掛斷電話。

調節項目

平衡

顯示

範圍

"CALL"�顯示消失，音響系統恢復接通。

"BAL"

"FAD"

"SubW"

左側�15�─�右側�15

後側�15�─�前側�15

15�—�＋ 15

音量控制器

低音揚聲器

音量 *¹

SRS�WOW 選擇

"AmpB"

平坦 /�+6/�+12/�+18

（dB）

低音提昇電平 *²

可以在播放時增加雄厚的重低音，形成三維音場。

中央頻率提昇 *²"AmpF"

通常 /�低

1^{�進入 WOW 選擇模式}

按下�[WOW]�按鈕。

顯示�"WOW�SEL"。

低音揚聲器

"LPF"

通過 /120/80/50�Hz

低通濾波器 *¹

音量偏置

"V-OFF"

8�—�±0

2^{�選擇 WOW 項目}

按下�[WOW]�按鈕。

每次按下該按鈕，SRS�WOW 選擇按照以下變換：

量不同的設定。

- 有關可以由本機控制的功率放大器，請參照樣

本或者使用說明書。

將音像提高一級，調節低音和音場。 "Low"

將音像提高二級，調節低音和音場。 "High"

變換至�'SRS�WOW 控制 '�的設定值。 "User"

恢復至無 SRS�WOW 的普通音響。

"Off"

．如果停止操作 3 秒鐘， SRS�WOW 選擇關閉。

接通� TruBass� 和� SRS� 3D� 的數值，將

FOCUS�的數值設定為高。

^{退出音響控制模式}

按下�[AUD]�按鈕。

SRS�WOW SRS�FOCUS SRS�TruBass SRS�3D

High

Low

Off

High

Low

Off

低音揚聲器輸出

接通或切斷低音揚聲器輸出。

按下�[AM ]�按鈕�1 秒鐘以上。

每次按下按鈕，低音揚聲器輸出切換成接通或切

斷。

接通時，顯示�"SubW�On"。

．當�' 切換預輸出 ' （第 60 頁）設定為�"SWPRE�

SW"�時，可以控制該項目。

46 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

SRS�WOW 控制

． "User"（用戶）�顯示：在�' 均衡器類型的 PRO （專

門）調整 '�設定的數值（第

48 頁）。

分別調節各 SRS�WOW 功能。

1^{�進入 WOW 控制模式}

按下�[WOW]�按鈕�1�秒鐘以上。

顯示�"WOW�CTRL"。

．可以調整選擇的均衡器類型。

調整項目取決於�' 均衡器模式 '�設定（第 60 頁）。

有關調整的詳細內容，請參照� ' 均衡器類型的

EASY （簡便）調整 ' （第 47 頁）或� ' 均衡器類

型的 PRO （專門）調整 ' （第 48 頁）。

2^{�選擇需要調節的 WOW 項目}

按下�[FM+]�或�[AM� ]�按鈕。

每次按下按鈕，可調節的項目按照以下切換。

3 ^{退出均衡器控制模式}

^{�調節 WOW 項目}

按下�[EQ] 按鈕 1 秒鐘以上。

按下�[4 ]�或者�[¢]�按鈕。

如果停止操作 10 秒鐘，這時的均衡器類型即被註

卌，均衡器控制模式自動關閉。

調節項目

顯示

範圍

0(Off)/1(Low)/

2(High)

SRS�FOCUS�設定 "FOCUS"

SRS�TruBass�設定 "TB"

Off/On

SRS�3D 設定

"SRS"

均衡器類型的 EASY （簡便）調整

^{�退出 WOW 控制模式}

按下�[WOW]�按鈕。

當�' 均衡器模式 '�為�"EASY"�時，調整在�' 均衡器控

制 '�中選擇的均衡器類型的效果。

^{參照�' 均衡器控制（' 第 47 頁），選擇均衡器類型。}

． TruBass：對播放加重低音進行補償。

． FOCUS：變化揚聲器的垂直虛擬位置，調節音響

效果，增強或降低音響範圍。

^調整效果

按下�[FM+]�或�[AM ]�按鈕。

每次按下按鈕，均衡器的效果即按照以下切換：

． SRS�3D：產生自然的立體音場。

．在使用調諧器音源時無法設定�SRS�3D。

設定效果

顯示

"Hi"

高

中

低

"Mid"

"Lo"

均衡器控制

^{退出均衡器控制模式}

按下�[EQ] 按鈕 1 秒鐘以上。

對於不同形式的音樂，可以呼出最佳音響預設。

如果停止操作 10 秒鐘，這時的均衡器類型即被註

卌，均衡器控制模式自動關閉。

^{進入均衡器控制模式}

按下�[EQ]�按鈕。

顯示�"EQ�EASY"�或�"EQ�PRO"。

^{選擇均衡器類型}

按下�[EQ]�按鈕。

每次按下按鈕，均衡器類型即按照以下切換：

均衡器類型

搖滾樂

舞曲

顯示

"Rock"

"Dance"

"Jazz"

爵士樂

流行音樂

莊重音樂

輕音樂

"Pops"

"Heavy"

"Soft"

高調音樂

輕音樂

"Sharp"

"Light"

"Natural"

自然

中文 47

Download from Www.Somanuals.com. All Manuals Search And Download.

總體特性

均衡器類型的 PRO （專門）調整

均衡器類型調整的預設記憶

當�' 均衡器模式 '�為�"PRO"�時，調整在�' 均衡器控

制 '�中選擇的均衡器類型的效果。

可以預設�' 均衡器類型的 PRO （專門）調整 '。

1 ^{參照�'均衡器類型的PRO（專門）調整（' 第48頁），}

調整均衡器類型。

^{參照�' 均衡器控制（' 第 47 頁），選擇均衡器類型。}

^{選擇調整項目}

按下�[FM+]�或�[AM ]�按鈕。

每次按下按鈕，可調節的項目按照以下切換。

^{預設調整數值}

按下�[1]�－�[3]�按鈕 1 秒鐘以上。

呼出設定數值

3 ^{調整該項目}

按下�[

]�或�[

]�按鈕。

^{進入均衡器控制模式}

按下�[EQ]�按鈕。

顯示�"EQ�PRO"。

調節項目

顯示

範圍

60/70/80/100 或者 150

低音中心頻率 "BasF"

．如果顯示�"EQ�EASY"，請參照�' 均衡器模式 '�（第

60 頁），將模式設定為�"EQ�PRO"。

低音音量

低音 Q 係數 "BasQ"

低音擴展 "EXT"

中音中央頻率 "MidF"

中音音量 "MidLV"

"BasLV"

12�—�+12

1.00/1.25/1.50/2.00

接通 / 切斷

2 ^{呼出設定數值。}

按下�[1]�－�[3]�按鈕。

0.5/1.0/1.5/2.0�kHz

12�—�+12

中音 Q 係繫數 "MidQ"

高音中央頻率 "TreF"

1.0/2.0

10.0/12.5/15.0/17.5�kHz

12�—�+12

高音音量

"TreLV"

電影選擇

選擇電影顯示。

．對應低音 Q 係數設定值，低音中央頻率中可以設

定的頻率按照以下改變。

進入電影選擇模式

按下�[MOVIE]�按鈕 1 秒鐘以上。

顯示��"Movie"。

低音 Q 係數

1.00/1.25/1.50

2.00

低音中央頻率

60/70/80/100

60/70/80/150

2 ^選擇電影

按下�[MOVIE]�按鈕。

每次按下按鈕，電影按照以下切換：

．當低音擴展設定為接通時，低音頻率響應擴展

20%。

3 ^{退出均衡器控制模式}

電影

顯示

按下�[EQ] 按鈕 1 秒鐘以上。

電影掃描

電影 1

電影 2

電影 3

電影 4

電影 5

電影 6

電影 7

電影 8

切斷

"MovieScn"

"Movie�1"

"Movie�2"

"Movie�3"

"Movie�4"

"Movie�5"

"Movie�6"

"Movie�7"

"Movie�8"

"MovieOff"

如果停止操作 10 秒鐘，這時的均衡器類型即被註

卌，均衡器控制模式自動關閉。

3 ^{退出電影選擇模式}

按下�[MOVIE]�按鈕 1 秒鐘以上。

如果停止操作 10 秒鐘，此時的電影被登錄，並

且自動關閉電影選擇模式。

48 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

切換顯示

．在播放無光盤標題、音軌標題、歌曲標題、歌曲

集名稱或者演員姓名的光盤時，如果選擇了光盤

標題、音軌標題、歌曲標題�&�演員姓名、或者歌

曲集名稱� &� 演員姓名，將顯示音軌號碼和播放時

間。

切換顯示的資訊。

按下�[DISP]�按鈕。

每次按下按鈕，顯示按照以下切換。

調諧器音源

資訊

顯示

頻率

電台名稱或者頻率

形象符號

時鐘

"SNPS"

CD�和外部光盤音源

資訊

顯示

音軌號碼�＆�播放時間

光盤名稱

光盤標題

音軌標題

形象符號

時鐘

"DNPS"

"D-Title"

"T-Title"

MP3/WMA�音源 (DPX-MP4070/DPX-MP4070B)

資訊

顯示

音軌號碼�＆�播放時間

檔案夾名稱

"Folder"

"File"

檔案名稱

歌曲標題�＆�演員姓名

歌曲集名稱�＆�演員姓名

形象符號

"Title"

"Album"

時鐘

磁帶音源

資訊

播放面�＆�磁帶計數

形象符號

時鐘

輔助輸入音源

資訊

輔助輸入名稱

形象符號

時鐘

待機模式

資訊

形象符號＆圖形

時鐘＆圖形

時鐘

中文 49

Download from Www.Somanuals.com. All Manuals Search And Download.

總體特性

照明顏色選擇

用戶照明顏色設定

設定顯示顏色。

使用 RGB 調整的照明顏色可以專門設定。

1 ^{進入照明顏色選擇模式}

按下�[COL]�按鈕。

顯示 “Illumi”。

1 ^{進入照明顏色選擇模式}

按下�[COL]�按鈕。

顯示 “Illumi”。

2 ^{選擇照明顏色}

2 ^{選擇調整的顏色}

按下�[

]�或者�[

]�按鈕。

每次按下按鈕，可以調整的顏色即按照以下切換：

按下�[COL]�按鈕。

每次按下按鈕，照明顏色即按照以下切換：

照明顏色

顯示

調整顏色

紅色

顯示

從 “藍色” 至 “薄荷色” 掃描。 "V.Color"

"R"�閃爍

"G"�閃爍

"B"�閃爍

藍色

"Blue"

綠色

火星紅色

白色

"Mars�Red"

"White"

藍色

3 ^調整顏色

按下�[FM+]�或�[AM ]�按鈕。

每次按下按鈕，顏色的濃度即按照以下改變：

淡紫色

麝香葡萄色

粉紅色

天藍色

檸檬色

紫色

"Lavender"

"Muscat"

"Pink"

"Sky�Blue"

"Lime"

顏色的濃度

關閉

顯示

"X0"

"X1"

"Violet"

淡

淺綠色

橙色

"Aqua"

"Orange"

"Mint"

濃

"X4"

薄荷色

用戶顏色

^{退出照明顏色選擇模式}

按下�[COL]�按鈕 1 秒鐘以上。

"RX/GX/BX"

如果停止操作10 秒鐘，這時的照明顏色即被決定，

照明顏色選擇模式自動關閉。

． “用戶顏色”可以呼出在 ' 用戶照明顏色設定 '（第

50 頁）中設定的顏色。

3 ^{退出照明顏色選擇模式}

按下�[COL]�按鈕 1 秒鐘以上。

調節時鐘

如果停止操作10秒鐘，這時的照明顏色即被註卌，

照明顏色選擇模式自動關閉。

^{選擇時鐘顯示}

按下�[DISP]�按鈕。

^{進入時鐘調節模式}

按下�[DISP]�按鈕�1�秒鐘以上。

‡ 指示燈閃爍。

^調節時間

按下�[FM+]�或者�[AM ]�按鈕。

調節分鐘

按下�[4 ]�或者�[¢]�按鈕。

4 ^{退出時鐘調節模式}

按下�[DISP]�按鈕。

50 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

電台 / 光盤命名（SNPS/DNPS）

輔助輸入顯示設定

對電台或者�CD�附加標題。

選擇當該裝置切換到內部輔助輸入音源時的顯示。

1 ^{接收 / 播放需要附加名稱的電台 / 光盤}

1 ^{選擇輔助輸入音源}

按下�[SRC]�按鈕。

選擇�"AUX"�顯示。

．請參照� ' 切換顯示 ' （第 49 頁），選擇� "DNPS"�

或者� "SNPS"� 顯示。如果不選擇� "DNPS"� 或

"SNPS"，則無法對音源附加名稱。

2 ^{進入輔助輸入顯示設定模式}

按下�[NAME.S]�按鈕�2�秒鐘以上。

顯示�"Name�Set"。

2 ^{進入名稱設置模式}

按下�[NAME.S]�按鈕�2�秒鐘以上。

顯示�"Name�Set"。

^{選擇輔助輸入顯示}

按下�[4 ]�或者�[¢]�按鈕。

每次按下按鈕，即按照以下顯示切換。

． "AUX"

^{將光標移動到輸入字符的位置}

按下�[4 ]�或者�[¢]�按鈕。

． "TV"

． "VIDEO"

4 ^{選擇字符類型}

． "GAME"

． "PORTABLE"

． "DVD"

按下�[

]�按鈕。

每次按下按鈕，字符類型按照以下切換。

字符類型

大寫字母

小寫字母

顯示

"A"

^{退出輔助輸入顯示設定模式}

按下�[NAME.S]�按鈕。

"a"

5 ^選擇字符

按下�[FM+]�或者�[AM ]�按鈕。

．如果操作停止�10�秒鐘，則選擇當時的名稱，並且

輔助輸入顯示設定模式關閉。

．衹有當使用內置的輔助輸入或選購的� KCA-S210A�

輔助輸入時，纔能夠設定輔助輸入顯示。

．將本機的電池取出後，輔助輸入名稱將恢復到�

"AUX"。

．可以使用帶數字按鈕的遙控器輸入字符。

例：如果輸入�"DANCE"。

字符

"D"

"A"

按鈕

[3]

按下的次數

[2]

"N"

"C"

"E"

[6]

[2]

[3]

^{重複操作步驟�3�至步驟�5，輸入名稱。}

7 ^{退出名稱設定模式}

按下�[NAME.S]�按鈕。

．如果操作停止�10�秒鐘，則當時的名稱被記憶，並

且名稱設定模式關閉。

．記憶體號碼

�-�FM�&�AM：30�個電台

�-�內部�CD�播放機：10�片光盤

�-�

外部�CD�換片機 / 播放機：根據�CD�換片機 /�

播放機而有所不同。請參照�CD�換片機 / 播放

機使用說明書。

．使用與命名相同的操作方法可以更改電台 /CD� 的

名稱。

中文 51

Download from Www.Somanuals.com. All Manuals Search And Download.

調諧器特性

��

� � �

�

��

�

預設電台號

波段顯示

頻率顯示

AUTO�指示燈

ST�指示燈

遙控器的功能

直接調諧

調諧

選擇電台。

輸入頻率進行調諧。

1 ^{選擇調諧器音源}

按下�[SRC]�按鈕。

選擇�"TUNER"�顯示。

1 ^選擇波段

按下�[FM]�或者�[AM]�按鈕。

^{進入直接調諧模式}

2 ^選擇波段

按下遙控器上的�[DIRECT]�按鈕。

顯示�"-�-�-�-"。

按下�[FM+]�或者�[AM ]�按鈕。

每次按下�[FM+]�按鈕，波段即在�FM1、 FM2�和

FM3�之間切換。

3 ^輸入頻率

按下遙控器上的數字按鈕。

例：

3 ^{上昇或者下降調諧波段}

按下�[

]�或者�[

]�按鈕。

所需頻率

按鈕

92.1�MHz （FM）

810�kHz （AM）

[9],�[2],�[1]

[8],�[1],�[0]

．接收立體聲電台時， "ST"�指示燈點亮。

取消直接調諧�

按下遙控器上的�[DIRECT]�按鈕。

52 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

電台預設記憶

預設調諧

向記憶體輸入電台。

呼出記憶體中的電台。

1 ^選擇波段

按下�[FM+]�或者�[AM ]�按鈕。

1 ^選擇波段

按下�[FM+]�或者�[AM ]�按鈕。

^{選擇向記憶體輸入的頻率}

按下�[

]�或者�[

]�按鈕。

^呼出電台

在�[1]�－�[6]�中按下需要的按鈕。

^{將頻率輸入記憶體}

在�[1]�－�[6]�中按下需要的按鈕�2�秒鐘以上。

預設號碼顯示閃爍�1�次。

頻率間距設定

在每個波段上， [1]�－�[6]�按鈕分別可以記憶�1�個

電台。

改變調諧頻率間距。初始設定為�FM�波段�50�kHz，

AM�波段�9�kHz。

^切斷電源

按下�[SRC]�按鈕�1�秒鐘以上。

自動記憶輸入

2 ^{切換頻率間距}

將接收良好的電台自動輸入記憶體。

在按下�[1]�和�[5]�按鈕的同時，按下�[SRC]�按鈕。

頻率間隔改變到�FM�波段�200�kHz�和�AM�波段�

10�kHz。

^{選擇自動記憶輸入的波段}

按下�[FM+]�或者�[AM ]�按鈕。

2 ^{進入選單模式}

按下�[FNC]�按鈕�1�秒鐘以上。

顯示�"Function"。

．重複相同的操作，恢復到初始設定。

．切換頻率間距時，在記憶體中的頻率被刪除。

^{選擇自動記憶輸入模式}

按下�[FM+]�或者�[AM ]�按鈕。

選擇�"A-Memory"�顯示。

^{開啟自動記憶輸入}

按下�[

]�或者�[

]�按鈕�2�秒鐘以上。

當向記憶體輸入了可以接收的� 6� 個電台時，自動

記憶輸入關閉。

中文 53

Download from Www.Somanuals.com. All Manuals Search And Download.

錄音座特性

�

� ��

��

�

��

指示燈

重複播放指示燈

空白跳躍指示燈

�指示燈

Dolby�B�NR 指示燈

MTL�指示燈

磁帶計數顯示

播放磁帶

Dolby�B�NR

按下�[B�NR]�按鈕。

當插入磁帶時

每次按下按鈕， Dolby�B�NR 切換成為接通或者切

斷。

按下�[SRC]�按鈕。

選擇�"TAPE"�顯示。

接通時， "B�NR�On"�指示燈點亮。

2 ^{插入磁帶。}

．插入磁帶時，�

�指示燈點亮。

選擇磁帶型式

需要播放相反一側時

同時按下�[

]�按鈕。

彈出磁帶

按下�[MTL]�按鈕。

每次按下按鈕，磁帶型式按照以下切換。

按下�[

]�按鈕。

磁帶型式

顯示

CrO²（Type�II）， FeCr

金屬（Type�IV）

（Type�III）， "MTL�On"

普通（Type�I）

"MTL�Off"

快進和快退

快進

按下�[FM+]�按鈕。

按下�[

]�按鈕時釋放。

快退

按下�[AM ]�按鈕。

按下�[38 ]�按鈕時釋放。

54 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

DPSS （Direct�Program�Search�System）

空白跳越

顯示跳越的歌曲，並且快進或者快退。

當未錄音的部分持續�10�秒鐘以上時，自動快進。

按下�[B.S]�按鈕。

跳越後面的歌曲

每次按下按鈕，空白跳越切換成為接通或者切斷。

接通時，顯示�"B.S�On"。

按下�[

]�按鈕。

每次按下按鈕，跳越的歌曲號碼增加。

跳越至前面的歌曲

按下�[

]�按鈕。

每次按下按鈕，跳越的歌曲號碼增加。

索引掃描

取消 DPSS

按下�[38 ]�按鈕。

播放正在欣賞的磁帶中每首歌曲的開頭部分，尋找

需要欣賞的歌曲。

在歌曲開始的前� 5� 秒鐘，有時可能將前一首歌曲

作為當前的歌曲。

．最多可以跳越�9�首歌曲。

1^{�開始索引掃描}

按下�[SCN]�按鈕。

顯示�"IDX�SCAN"。

2^{�當播放需要欣賞的歌曲時鬆開}

按下�[SCN]�按鈕。

遙控器的�DPSS

使用遙控器的控制號碼按鈕，指定需要跳越的歌曲。

音樂反復

^{指定跳越的歌曲}

按下遙控器上的號碼按鈕。

反復播放當前的歌曲。

按下�[REP]�按鈕。

2 ^{跳越後面的歌曲}

每次按下按鈕，音樂反復切換成為接通或者切斷。

接通時，顯示�"Repeat"。

按下�[

]�按鈕。

跳越至前面的歌曲

按下�[

]�按鈕。

取消�DPSS

按下�[38 ]�按鈕。

．在歌曲開始的前� 5� 秒鐘，有時可能將前一首歌曲

作為當前的歌曲。

．最多可以跳越�9�首歌曲。

中文 55

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/�MP3/�WMA/�外部光盤控制特性

�

��

�

��

M.RDM�指示燈

音軌時間

音軌號

SCN�指示燈

REP/D.REP�指示燈

CH�指示燈

光盤號

�指示燈

WMA/MP3�指示燈

播放�CD�和�MP3/WMA

．本機可以播放的� MP3/WMA� 媒體為� CD-ROM、

CD-R�和�CD-RW。

插入�CD�時

按下�[SRC]�按鈕。

選擇�"CD"�顯示。

媒體的格式必須是� ISO� 9660� Level� 1、 Level� 2、

Joliet� 或者� Romeo。有關記錄� MP3/WMA� 資料

的方法和應遵守的注意事項，請參照� ' 關於播放�

MP3/WMA�的注意事項 ' （第 42 頁）。

在製作�MP3/WMA�媒體之前，請閱讀該部分的內

容。

．插入�CD�時，�

．可以播放�MP3/WMA�的機型如下所示。�

KDC-MP4070/KDC-MP4070B

�指示燈點亮。

．播放 MP3 時， "MP3"�指示燈點亮。

．播放 WMA 時， "WMA"�指示燈點亮。

暫停和播放

按下�[38 ]�按鈕。

播放外部光盤

每次按下按鈕，切換成為暫停或者播放。

播放放置在與本機連接的可選附件光盤播放機中的

光盤。

彈出�CD

按下�[

]�按鈕。

按下�[SRC]�按鈕。

選擇所需光盤播放機的顯示。

顯示例：

．不得利用適當配器使用 8cm （3 英寸） CD。利用

適配器將 8cm�CD 插入本機可能造成損壞。

顯示

光盤播放機

CD�換片機

MD�換片機

"CD�CH"

"MD�CH"

56 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

帶遙控器的光盤換片機的功能

直接光盤搜索

暫停和播放

按下�[

]�按鈕。

每次按下按鈕，切換成為暫停或者播放。

輸入光盤號碼，進行光盤搜索。

1 ^{輸入光盤號碼}

． 10 光盤顯示為 “0”。

．根據外接的光盤播放機，可使用的功能和可顯示

的資訊有所不同。

按下遙控器上的號碼按鈕。

^{進行光盤搜索}

按下�[DISC+]�或者�[DISC-]�按鈕。

取消直接光盤搜索

按下�[38 ]�按鈕。

快進和快退

快進

．選擇光盤 10 時輸入“0”。

按住�[

]�按鈕。

鬆開手指，在該處播放光盤。

快退

按住�[4 ]�按鈕。

鬆開手指，在該處播放光盤。

音軌 / 檔案 / 光盤 / 檔案夾反復

重複播放您所欣賞的光盤換片機或者�MP3/WMA�檔

案夾中的歌曲、光盤。

按下�[REP]�按鈕。

每次按下按鈕，反復播放按照以下切換。

音軌 / 檔案搜索

CD�和外部光盤音源

在光盤或者�MP3/WMA�檔案夾中選擇歌曲。

按下�[

]�或者�[

]�按鈕。

反復播放

顯示

音軌反復

"Repeat"

"D-Repeat"

光盤反復

（在光盤換片機中）

光盤換片機 /MP3/WMA�的功能

光盤搜索 / 檔案夾搜索

切斷

MP3/WMA�音源

選擇放入光盤換片機的光盤或者在�MP3/WMA�媒體

中記錄的檔案夾。

反復播放

檔案反復

檔案夾反復

切斷

顯示

"File�REP"

"Fold.REP"

按下�[AM ]�或者�[FM+]�按鈕。

遙控器的功能

直接音軌 / 檔案搜索

輸入音軌 / 檔案號碼，進行音軌 / 檔案搜索。

1 ^{輸入音軌 / 檔案號碼}

按下遙控器上的號碼按鈕。

^{進行音軌 / 檔案搜索}

按下�[

]�或者�[

]�按鈕。

取消直接音軌 / 檔按搜索

按下�[38 ]�按鈕。

中文 57

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/�MP3/�WMA/�外部光盤控制特性

DPX-MP4070/DPX-MP4070B�的功能

MP3/WMA�的功能

檔案夾選擇

掃描播放

播放您所欣賞的光盤或者�MP3/WMA�檔案夾中各首歌

曲的最初部分，搜索您需要的歌曲。

盡快選擇你所欣賞的檔案夾。

^{開始掃描播放}

按下�[SCN]�按鈕。

顯示�"Scan"。

1 ^{進入檔案夾選擇模式}

按下�[F.SEL]�按鈕。

在選擇模式狀態下，檔案夾資訊顯示如下。

檔案夾名稱顯示

^{當播放需要的歌曲時鬆開}

按下�[SCN]�按鈕。

顯示當前的檔案夾名稱。

KENWOOD

隨機播放

2 ^{選擇檔案夾等級}

按下�[FM+]�或者�[AM ]�按鈕。

使用� [FM+]� 按鈕可向下移動� 1� 級，使用� [AM ]

按鈕可向上移動 1 級。

按照隨機的順序，播放光盤或者�MP3/WMA�檔案夾

中的所有歌曲。

按下�[RDM]�按鈕。

每次按下按鈕，隨機播放切換成為接通或者切

在相同等級選擇檔案夾

斷。

按下�[

]�或者�[

]�按鈕。

使用�[4 ]�可移動到前一個檔案夾，使用�[¢]

按鈕可移動到下一個檔案夾。

接通時，顯示�"Random"。

．按下�[

]�按鈕時，開始下一首歌曲選擇。

返回最高級

按下�[3]�按鈕。

^{決定播放的檔案夾}

按下�[38 ]�按鈕。

光盤換片機的功能

換片機隨機播放

檔案夾選擇模式解除，播放在播放的檔案夾中的

MP3/WMA。

按照隨機的順序，播放光盤換片機中所有光盤的歌

曲。

．在檔案夾選擇模式中移動到其他檔案夾的方法與

在檔案夾搜索模式中的方法不同。

按下�[M.RDM]�按鈕。

每次按下按鈕，換片機隨機播放切換成為接通或

者切斷。

有關詳細內容，請參照� ' 關於播放� MP3/WMA� 的

注意事項 ' （第 42 頁）。

接通時，顯示�"M-Random"。

取消檔案夾選擇模式

按下�[F.SEL]�按鈕。

．按下�[¢]�按鈕時，開始下一首歌曲選擇。

文本 / 標題滾動

滾動顯示的�CD�文本、 MP3/WMA�文本或者�MD�標題。

按下�[SCRL]�按鈕。

58 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

功能設定

��

� � �

��

�

功能設定

．當隨後其他適用於上述基本操作方法的項目顯示

時，即進入該設定內容表。（通常在表中的最上

層設定為初始設定。）

設定在操作中發出的提示音等功能。

以下說明功能設定的基本操作方法。有關功能項目

和設定內容的參考，將在本操作說明之後介紹。

同時，對於不適用的說明依次進入。

1 ^{進入功能設定模式}

按下�[FNC]�按鈕 1 秒鐘以上。

顯示�"Function"。

2 ^{選擇功能設定項目}

按下�[FM+]�或�[AM ]�按鈕。

例：如果需要設定提示音，請選擇�"BEEP"�顯示。

3 ^{設定功能設定項目}

按下�[4 ]�或�[¢]�按鈕。

例：

當選擇了�"BEEP"�時，每次按下按鈕，即切

換成為�"BEEP�On"�或者�"BEEP�Off"。如設

定選單 1。

可以返回到步驟 2 繼續進行，設定其他項目。

4 ^{退出功能設定模式}

按下�[FNC]�按鈕。

中文 59

Download from Www.Somanuals.com. All Manuals Search And Download.

功能設定

待機模式

照明顏色模式

待機模式

切換預輸出

設定所需顯示的照明顏色模式。

在後側和低音揚聲器之間切換預輸出。（低音揚聲

器時，輸出無衰減控制效果的輸出。）

顯示

設定

顯示

設定

在調節音量時和衰減器接通

時，顯示從一種顏色改變到

另外一種顏色。

"COL�Sync"

"SWPRE�R"

"SWPRE�SW"

後側預輸出。

低音揚聲器預輸出。

"COL�Fix"

固定顏色設定。

待機模式

開機演示

待機模式

對比度調節

設定接通電源時的演示。

調節顯示的對比度。

顯示

設定

"Open�On"

"Open�Off"

電源接通時進行演示。

電源接通時不進行演示。

顯示和設定

"CONT�1"

"CONT�6"�( 初始設定 )

"CONT�11"

待機模式

均衡器模式

設定調整均衡器類型的方法。

顯示

設定

按鍵音調

均衡器類型的效果可以分 3 級

進行調整。

"EQ�EASY"

設定操作核對音（提示音）的接通 / 切斷。

均衡器類型可以按照低音，中

音和高音調整。

"EQ�PRO"

顯示

設定

"BEEP�On"

"BEEP�Off"

可以聽到提示音。

取消提示音。

60 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

待機模式

保安代碼

待機模式

導航靜音

因為從汽車上取下時需要保安代碼的許可操作，使

用保安代碼對本機進行特殊設定將有助於防盜。

在導航語音導向時對音響靜音。

顯示

設定

"NavM�Off"

"NavM�On"

音響不靜音

音響靜音

．當保安代碼功能開啟時，代碼無法更改，同時本功

能也無法解除。

注意，保安代碼可以設定為您所選擇的�4�位數字。

1 ^{選擇安全編碼模式}

按下�[FM+]�或�[AM ]�按鈕。

選擇�"CODESTBY"�顯示。

待機模式

電話消音

2 ^{進入安全編碼模式}

按下�[COL]�按鈕 2 秒鐘以上。

顯示�"WRITE"，並且顯示�"CODE�****"。

可以設定當電話打入時對音響靜音。

顯示

設定

^{輸入保安代碼}

按下�[1]�－�[4]�按鈕。

例：如果保安代碼為�"3510"。

"TelM�Off"

"TelM�On"

音響不靜音

音響靜音

步驟

按鈕

[1]

按下的次數

顯示

"3"

[2]

"5"

待機模式

內置輔助輸入設定

[3]

"1"

[4]

"0"

設定內置輔助輸入功能。

4 ^{確認保安代碼}

按下�[COL]�按鈕。

顯示

設定

顯示�"WRITE"，並且顯示�"1�CODE�****�"。

"AUX�Off"

"AUX�On"

選擇音源時不出現輔助輸入。

選擇音源時出現輔助輸入。

5 ^{進行步驟� 3� 至步驟� 4� 的操作，重新輸入保安代}

碼。

保安代碼功能開啟。

．如果輸入與步驟 3 不同的代碼，請從步驟 3 重新

操作。

待機模式

內置放大器消音設定

當從電池電源拆下時，按下復位按鈕

切換內置放大器消音控制的接通和切斷。接通該控

制可提高預輸出音質。

1 ^{接通電源。}

^{進行步驟�3�至步驟�4�的操作，輸入保安代碼。}

顯示

設定

顯示�"CODE�OK!"。

"AmpM�Off"

"AmpM�On"

開啟內置放大器。

關閉內置放大器。

本機可以使用。

中文 61

Download from Www.Somanuals.com. All Manuals Search And Download.

功能設定

調諧器模式

調諧模式

防盜警告燈

當關閉 ACC 後，本机上的紅色指示燈將發出閃爍，

對盜賊發出警告。

設定調諧模式。

調諧模式顯示

操作

顯示

設定

自動搜索 "Auto�1"

自動搜索電台。

"S.I�Off"

"S.I�On"

LED 切斷。

LED 閃爍。

預設電台

搜索

按照預設在記憶體中

的電台順序搜索。

"Auto�2"

手動

"Manual"

通常的手動調諧控制。

DPX-MP4070/DPX-MP4070B�的功能

待機模式

CD�讀取設定

FM�接收

單聲道接收

當在播放特殊格式的�CD�時，可以使用本設定進行

強制播放。

當立體聲廣播作為單聲道接收時，可以減少噪音。

顯示

設定

顯示

設定

"CD�READ�1"

"CD�READ�2"

播放�CD�以及�MP3/WMA。

強制播放�CD。

"MONO�Off"

"MONO�On"

單聲道接收切斷。

單聲道接收接通。

．如果設定為�"CD�READ�2"，則無法播放�

MP3/WMA。

調諧器模式

自動記憶輸入�

即使使用� "CD� READ� 2"� 模式，某些音樂� CD� 也

無法播放。

有關操作方法，請參照�' 自動記憶輸入' （第 53 頁）。

CD/MP3/WMA�和外部光盤音源

文本滾動

設定顯示的文本滾動。

顯示

設定

"SCL�Auto"

"SCL�Manu"

重複滾動。

當顯示更換時滾動。

．文本滾動如下所示。

�-�CD�文本

�-�

檔案夾名稱 / 檔案名稱 / 歌曲標題 / 音源姓名 /

歌曲集名稱

�-�MD�標題

62 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

遙控器的基本操作

��

�

��

不使用

��

安裝和更換電池

基本操作

使用兩節�"AA"�電池。

[VOL.]�按鈕

按圖示按住蓋使之滑動。

調節音量。

按照電池盒內的圖示，對准正極和負極插入電池。

[SRC]�按鈕

每次按下按鈕，音源進行切換。

有關音源的切換順序，請參照�' 選擇音源 ' （第�

45�頁）。

[ATT]�按鈕

快速降低音量。

再次按下時，恢復到前一等級。

2 警告

．將未使用的電池遠離兒童保存。如果萬一吞咽了

電池，應立即與醫生聯繫。

．不得將遙控器放在諸如儀錶板上側等較熱的位

置。

中文 63

Download from Www.Somanuals.com. All Manuals Search And Download.

遙控器的基本操作

調諧器音源

光盤音源

[FM]/�[AM]�按鈕

[

]/�[

]�按鈕

選擇波段。

執行音軌的前進和後退。

每次按下� [FM]� 按鈕，波段即在� FM1、 FM2� 和

FM3�之間切換。

[DISC+]/�[DISC ]�按鈕

執行光盤的前進和後退。

[

]/�[

]�按鈕

[

]�按鈕

向上或者向下調諧波段。

每次按下按鈕，歌曲暫停或者播放。

[0]�－�[9]�按鈕

按下按鈕�[1]�－�[6]�呼出預設電台。

在� ' 直接音軌 / 檔案搜索 ' （第 57 頁）和� ' 直接

光盤搜索 ' （第 57 頁）時，輸入音軌 / 光盤號碼。

[DIRECT]�按鈕

進入或者取消�' 直接調諧 ' （第 52 頁）模式。

磁帶音源

[

]/�[

]�按鈕

進行�'DPSS （Direct�Program�Search�System） ' （第

55 頁）。

[

]�按鈕

播放磁帶的另外一面。

[FM]�按鈕

磁帶快進。

按下�[

]�按鈕時釋放。

[AM]�按鈕

磁帶快退。

按下�[38 ]�按鈕時釋放。

[0]�－�[9]�按鈕

使用�' 遙控器的�DPSS' （第 55 頁）輸入歌曲的號

碼。

64 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

附件/安裝程序

附件

安裝程序

1. 為了防止短路事故，請拔下點火開關鑰匙，取下

蓄電池的

極端子。

2. 連接各裝置的輸入和輸出導線。

3. 連接電線束的揚聲器導線。

4. 按照接地導線、蓄電池導線和點火導線的順序連

接電線束。

..........�1

..........�6

5. 將電線束的連接器連接到裝置上。

6. 將裝置安裝到汽車中。

7. 連接步驟�1�所卸下的蓄電池� 極端子。

8. 按下復位按鈕。

2 警告

點火導線（紅色）、蓄電池導線（黃色）如果接觸汽車的

底盤（接地），會引起短路，導致火災，因此請連接通過

汽車保險絲盒的電源。

如果汽車的點火沒有�ACC�位置時，請以點火開關鑰匙將

點火導線連接在可� ON/OFF� 的電源上。將點火導線連接

到與蓄電池導線同時供給一般電壓的電源時，蓄電池將

會出現過負荷現象。

儀表板有蓋子時，請認真安裝，使擋板開閉操作時不要

碰撞蓋子。

保險絲燒斷時，應檢查導線等有無短路，然後更換規定

容量相同的保險絲。

部分光盤換片機需要連接用軟線。另外，為了防止短路

事故，請不要拆卸附在未連接的導線和端子上的外罩。

請將揚聲器導線分別連接相應的揚聲器端子上。共用揚

聲器負極導線、或接地導線接觸汽車金屬部位等，都有

可造成裝置的故障。

．系統僅連接兩個揚聲器時，請切實將兩極的連接器都僅

連接在前置輸出或後置輸出的其中一面。請不要採取將

在揚聲器的�+�連接器連接前置輸出、將�-�連接器連接

後置輸出那樣的方式。

．安裝結束後，請確認汽車制動器燈、方向指示燈和刮水

器等是否正常動作。

．本機安裝角度為�30�度以下為宜。

中文 65

Download from Www.Somanuals.com. All Manuals Search And Download.

連接

AUX�左路輸入（白色）

AUX 右路輸入（紅色）

前置左輸出（白色）

後置左輸出（白色）/

低音揚聲器左輸出（白色）

前置右輸出（紅色）

後置右輸出（紅色）/

低音揚聲器右輸出（紅色）

M4�8mmMAX

FM/AM�天線輸入

KENWOOD光盤換片機控制輸入

要連接光盤換片機時，請參照光

盤換片機的使用說明書。

保險絲（10A）

電線束（附件1）

不連接時，請不要將導線

從接頭中拉出。

請向電動天線的控制端子和玻璃印刷天線的增幅

放大器的電源連接。�

ANT. CONT

P.CONT

MUTE

電動天線控制導線（藍色）

連接另售的功率放大器時，向功率放大器的功率

控制端子連接。

功率控制導線（藍色/白色）

電話消音導線（茶色）

電話鈴響或通話時將連接接地端子。

有關KENWOOD導航系統的連接，請參照該導航系

統的使用說明書。

至汽車燈控制開關�

ILLUMI

減光控制導線（橙色/白色）

至具備外部放大器控制功能的放大器的

"EXT.AMP.CONT."�端子。

EXT.CONT.

外部放大器控制線（粉紅色/黑色）

白色 / 黑色

向前置左揚聲器

向前置右揚聲器

向後置左揚聲器

向後置右揚聲器

白色

灰色 / 黑色

灰色

綠色 / 黑色

綠色

紫色 / 黑色

紫色

汽車保險

絲盒

點火開關

鑰匙

ACC

點火導線（紅色）

蓄電池導線（黃色）

汽車保險絲盒�

（主保險絲）

接地導線（黑色）-（至汽車底盤）

�

蓄電池�

66 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

安裝

在安裝之前，應該檢查 CD 的操作，將本機放置水

平位置，操作 CD 的裝入 / 退出。

安裝

使用附件螺絲（M5×6mm， M5×7mm）固定在車

托架上。根據車型，車托架的安裝孔將有所不同。

當配線套件中包括接地線時（另行出售），使用位於裝

置後板上的固定螺絲固定。

螺絲（M4×8）

（選購）

附件3

（M5×6mm）

或�附件4

（M5×7mm）

附件2

（僅限於日產牌轎車）

．安裝時請務必使用所附的螺絲。使用附件以外的螺絲，

可能會造成本裝置的故障。

．請勿使用緊固力過強的電動螺絲刀等，以免底盤破損。

中文 67

Download from Www.Somanuals.com. All Manuals Search And Download.

故障檢修

無聲或小聲。

有時被認為是故障的現象，其實是因微小的操作或

配線失誤而造成。在要求維修之前，請參照下表稍

事檢查為盼。

音量控制器或者平衡調節設定在一端。





將音量控制器或者平衡調節設定在中央位

置。�

輸入 / 輸出導線或電線束沒有正確連接。



正確連接輸入 / 輸出導線或者電線束。參照

' 連接 '，正確進行連接。�

共同

電源不通。



卡帶有問題。

如使用其他卡帶而無異常，則是原使用卡帶

的問題。

音量偏置值過低。

保險絲燒斷。



確認導線等有無短路之後，更換規定容量相

同的保險絲。

揚聲器導線與汽車底盤等接觸。





請參照�' 音響控制 '（第�46�頁）部分的內容，

提高音量偏置。



正確連接導線、或對揚聲器導線妥善絕緣，

然後按下復位按鈕。

' 內置放大器消音設定 ' （第�61�頁）接通。�

設定為切斷。



有一種音源無法切換。

沒有插入媒體。



音質差（失真）。



設置您希望欣賞的媒體。如果本機中沒有媒

體，則無法切換到各個音源。

沒有連接換片機。

揚聲器導線被汽車兩側的螺絲壓住。

 檢查揚聲器導線。�

磁頭髒污。

 清潔磁頭。





連接換片機。如果換片機沒有與本機的輸入

端子連接，則無法切換到外部光盤音源。

揚聲器導線被共用。



將揚聲器輸出端子分別連接在各揚聲器端子

上。�

點火開關置於 OFF 時，存儲內容消失。



沒有正確連接蓄電池導線及點火導線。

 參照�' 連接 '，正確連接。

無觸摸音。�



使用了預輸出插孔。

 無法從預輸出插孔輸出觸摸音。

TEL 消音功能無效。

沒有正確連接 TEL 消音導線。





參照�' 連接 '，正確連接。

' 電話消音 ' （第�61�頁）接通。�

設定為切斷。

調光功能無效。�



沒有正確連接調光器導線。

 檢查調光器導線。



未連接�TEL�消音導線， TEL�消音功能卻有。



TEL�消音導線接觸汽車的金屬部位。

 將�TEL�消音導線與汽車金屬部位分開。

68 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

調諧器音源

光盤音源

收音機接收品質差。

沒有伸展汽車天線。

顯示�"AUX�EXT"，但無法進入外部光盤控制模式。

連接了不兼容的換片機。





伸展天線。

沒有連接天線控制導線。

參照�' 連接 '，正確連接。



請使用在�' 安全注意事項 '�的�' 關於與本機連

接的�CD�播放機 / 光盤換片機 ' （第�40�頁）

訊部分說明的光盤換片機。





使用直接調諧（Direct�Access�Tuning）功能無法輸入

所需頻率。

不播放指定光盤，而播放其他光盤。

指定光盤異常髒污。



輸入了無法接收的電台。





請進行光盤清理。

指定光盤號與光盤的放入位置不同。

排出光盤盒，確認指定光盤號。

光盤有較大損傷。

請使用其他光盤。



輸入可以接收的電台。

您試圖以�0.01�MHz�的單位輸入頻率。�

在�FM�波段可以指定的單位為�0.1�MHz。





磁帶音源

光盤裝入後立即退出。

光盤過於髒污。



無法取出磁帶。





參照�' 關於�CD' （第�44�頁）的清潔�CD�部

分的內容，對�CD�進行清潔。

由於切斷汽車�ACC�開關的時間已經超過了�10�

分鐘。

磁帶祗能在切斷汽車�ACC�開關後的�10�分鐘



無法取出光盤。

由於切斷汽車�ACC�開關的時間已經超過了�10�

分鐘。

之內取出。如果超過了�10�分鐘，請再次接

通�ACC�開關，然後按下彈出按鈕。





光盤祗能在切斷汽車�ACC�開關後的�10�分鐘

之內取出。如果超過了�10�分鐘，請再次接

通�ACC�開關，然後按下彈出按鈕。�

DPSS、磁帶前進和音樂反復功能的工作不正常。

樂曲之間的間隔過小，無法被識別。





樂曲之間至少應間隔�4�秒鐘。

樂曲之間的噪音過多，無法被識別。�

減少樂曲之間的噪音。



無法放入光盤。

已經放入了其他光盤。







按下�[0]�按鈕，取出光盤。

空白跳越無法工作。



由於噪音過大，無法識別未錄音部分。

 減少樂曲之間的噪音。

無法完成直接搜索。�



其他功能接通。

 將隨機播放或者其他功能切斷。

空白跳越功能在錄音的部分動作。



由於錄音電平過低，因此被識別為未錄音部分。

 切斷空白跳越功能。

音軌搜索功能無法工作。�

關於光盤 / 檔案夾的第一首或者最後一首樂曲。





對於各光盤 / 檔案夾，無法在反方向進行第

一首樂曲的音軌搜索，並且無法在正方向進

行最後一首樂曲的音軌搜索。

' 音樂反復 ' （第 55 頁）被強行解除。

進行了切斷電源以及音源選擇等操作。





進行了切斷電源以及音源選擇等操作後�，

音樂反復將被強行解除。

中文 69

Download from Www.Somanuals.com. All Manuals Search And Download.

故障檢修

MP3/WMA�音源

下列資訊表示系統的狀態。

無法播放�MP3/WMA。

媒體擦傷或者骯髒。

EJECT:�

光盤盒未放入換片機內。光盤盒未完全

放入。

 請將光盤盒切實放入。

本機中沒有�CD。

 放入�CD。





參照�' 關於�CD' （第�44�頁）的清潔�CD�部

分的內容，對媒體進行清潔。

播放�MP3/WMA�時發生跑音。

媒體擦傷或者骯髒。



No�Disc:�

Error�04:

光盤盒沒有光盤。

 請將光盤放光盤盒內。



參照�' 關於�CD' （第�44�頁）的清潔�CD�部

分的內容，對媒體進行清潔。

光盤過於髒污。�光盤異常髒污。光盤裝

入方向不對（反面）。光盤上擦傷多。

 將光盤弄乾淨，正確裝入。

錄音條件不良。

重新錄音，或者使用其他媒體。





MP3/WMA�音軌時間無法正確顯示。



Error�05:�

光盤裝入方向不對（反面）。

 正确裝入光盤。



根據�MP3/WMA�的錄音條件，有時無法正

常顯示。

Blank:�

MD�無錄音內容。

發生了下述情況時，請與就近的服務中心

聯繫：

No�Track:�

Error�77:

MD�上雖無存儲音軌內容，但有光盤名。

因故不能正常運轉。

即使連接了換片機，但換片模式無法接通，並

且在換片機模式狀態下顯示�"AUX�EXT"。

 按下本機的復位按鈕。如�"Error�77"�

顯示仍不消失時�，請與附近的服務中

心洽談。

Error�99:�

光盤盒發生了故障。或者本機由於某種原

因發生了故障。

 檢查光盤盒。然後按本機的復位按鈕。

如�"Error�99"�顯示仍不消失時，請與附

近的服務中心洽談。

70 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

Hold:

由於光盤自動換片機內部溫度達�60℃�以

上，保護線路開始運轉。

 降低光盤自動換片機安裝處的溫度。

溫度下降後，光盤自動換片機即開始

播放。

No�Name:�

在播放沒有預設光盤名稱的�CD�時，試圖

顯示�DNPS。

Load:�

CD�換片機更換光盤時。

Reading:�

本機正在讀取光盤上的資料。

�(閃爍):� CD�播放部分沒有正常運行。

 重新插入�CD。如果�CD�無法彈出、或

者即使正確地重新插入�CD�也依然閃

爍，請切斷電源，與附近的服務中心洽

談。

�(閃爍):� 磁帶播放部分沒有正常運行。

 重新插入磁帶。如果磁帶無法彈出、或

者即使正確地重新插入磁帶也依然閃

爍，請切斷電源，與附近的服務中心洽

談。

N/A�File:

Protect:

播放的�MP3/WMA�格式本機無法使用。



播放了防止複製的檔案。



----

中文 71

Download from Www.Somanuals.com. All Manuals Search And Download.

87.5�MHz�—�108.0�MHz

200�kHz�間隔�:�87.9�MHz�—�107.9�MHz

:�

全帶寬功率（THD�1�％以下）�

:�22�W�×�4

預輸出電模平/負載

:�1800�mV/10�kΩ

50�W�×�4

9�kHz�間隔�:�

531�kHz�—�1611�kHz

530�kHz�—�1700�kHz

可用靈敏度（S/N�=�20dB）

:�28�dB（µ 25�µV）

10�kHz�間隔�:�

:�

最大輸入電壓

:�1200�mV

輸入阻抗

:�100�kΩ

20�Hz�—�20�kHz

:�

抖晃度�(WRMS)

:�0.1�％

頻率響應�(70�μS)

:�40�Hz�—�20�kHz�(±3�dB)

分隔度�(1�kHz)

:�35�dB

4.76�cm�/�秒

:�

數字濾波器（數/模）

:�8倍取樣

數/模轉換器

:�1�Bit

心軸速度

GaAlAs

:�

500�—�200�rpm（CLV）�

無法測量極限

:�

10�Hz�—�20�kHz

規格

規格可能會變更，恕不另行通知。

總諧波失真（1�kHz）�

:�0.01�%

信噪比（1�kHz）

:�100�dB

動態範圍

:�93�dB

通道分離

:�85�dB

MP3�解碼�(KDC-MP-4070/KDC-MP4070B)

:�MPEG-1/2�Audio�Layer-3�標準

WMA�解碼�(KDC-MP-4070/KDC-MP4070B)

:�Windows�Media�Audio�標準

調頻調諧器部

頻率範圍

50�kHz�間隔�:�

可用靈敏度（S/N�=�30dB）

:�9.3dBf（0.8�µV/75�Ω）

靜噪靈敏度（S/N�=�50dB）

:�15.2dBf（1.6�µV/75�Ω）

頻率響應（±3.0�dB）

:�30�Hz�—�15�kHz

信噪比（單聲道）

:�70�dB

選擇性（±400�kHz)

:��

≥

�80�dB

音頻部

最大輸出功率

立體聲分隔度（1�kHz）

:�30�dB

調幅調諧器部

頻率範圍

預輸出阻抗

:�≤�600�Ω

輔助輸入

頻率響應（±1�dB）

卡式錄音座部

磁帶速度

共同

工作電壓（允許11-16�V）�

:�14.4�V

電流消耗

:�10�A

安裝尺寸（寬×高×深）�

:�178×100×155�mm

重量

:�2.3�kg

信噪比

杜比NR�OFF�:�50�dB

杜比B�NR�ON�:�60�dB

CD�播放機部

激光二極管

抖晃度

:�

頻率響應（±1�dB）

72 中文

Download from Www.Somanuals.com. All Manuals Search And Download.

차례

리모콘을�이용한�DPSS

블랭크의�건너뛰기

색인�스캔

안전상의�주의

경고

주의

주

음악의�반복

CD/MD/MP3/WMA 외부�디스크�

주

컨트롤�기능

CD�&�MP3/WMA�재생

외부�디스크의�재생

빨리�감기와�되감기

트랙�/�화일�검색

디스크�검색 / 폴더�검색

다이렉트�트랙�/�파일�검색

다이렉트�디스크�검색

트랙�/�디스크�/�폴더�/�화일�반복

트랙�스캔

랜덤�재생

매거진�랜덤�재생

폴더�선택

텍스트�/�타이틀�화면�이동�(scroll)

카세트�테이프

MP3/WMA�재생의�주의점

CD 에�관해서

일반�기능

전원

소스의�선택

볼륨

소음기

오디오�컨트롤

서브�우퍼�출력

TEL�뮤트

SRS�WOW 선택

SRS�WOW�컨트롤

이퀼라이저�컨트롤

EASY 에서�이퀼라이저�타입의�변경

PRO 에서�이퀄라이저�타입의�변경

기능�설정

일류미네이션�컬러�모드

콘트라스트 ( 대비 )�조정

터치�센서�톤�(tone)

사전�출력의�변환

데모의�시작

이퀄라이저�모드

안전�코드

네비게이션�뮤트

TEL�뮤트

내장�보조입력�설정

내장�앰프�설정

보안장치�표시

CD�읽기�설정

튜닝�모드

이퀄라이저�타입�변경의�메모리�사전�설

정

영화�선택

디스플레이의�변환

일류미네이션�컬러�선택

이용자�일류미네이션�컬러�설정

시간�조정

방송국�/�디스크의�이름�붙이기�(SNPS�/�

DNPS)

보조입력원�설정

튜너�기능

튜닝

다이렉트�액세스�튜닝

방송국�사전�설정�메모리

자동�메모리�등록

사전�설정�튜닝

모노럴�수신�

자동�메모리�등록

텍스트�스크롤

리모콘의�기본�조작

부속품 /�설치�순서

와이어를�단자에�접속

설치

101

102

103

104

108

주파수�스텝�설정

카세트�플레이어�기능

카세트�테잎의�재생

빨리�감기와�되감기

돌비�B�NR

테잎�타입의�선택

DPSS�( 다이렉트�프로그램�검색�시스템 )

트러블�처치�가이드

사양

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

안전상의�주의

2 경고

2 주의

고장�또는�화재를�방지하기�위해�다음의�주의

사항을�준수해�주십시오 :

• 본�기기가�소정의�위치에�꼭�고정될�때까지�단단

히�삽입해�주십시오 .�꼭�끝까지�삽입하지�않으면�

충격이�가해졌을�때�빠지는�일이�있습니다 .

기기의� 고장을� 방지하기� 위해� 다음의� 주의사

항을�준수해�주십시오 :

• 본�기기가�마이너스�12V�DC�전원�어스를�연결

하고�있는지�확인해�주십시오 .

• 본�기기의�상하�커버를�열지�마십시오 .

• 인입�코드，배터리�또는�어스선을�확장할�경

우는�반드시�자동차급�와이어�또는�0.75mm²

（AWG18 �이상의�와이어를�사용하고�와이어의�

열화 �피복의�손상이�일어나지�않도록�해�주십시

오 .

• 단락을�방지하기�위해�본�기기�내부에�금속물�(코

인�또는�금속제�공구�등 ) 을�절대로�넣지�마십시

오 .

• 본�기기를�직사�광선 �고온 �습기가�많은�곳에�놓

지��마십시오 .�또��먼지가�많은�곳이나�물이�튈�

가능성이�있는�곳에�설치하지�마십시오 .

• 퓨즈를�교환할�경우에는�규격의�신품만을�사용해�

주십시오 .�규격�이외의�퓨즈를�사용하면�오작동

이�발생하는�경우가�있습니다 .

• 퓨즈�교환시의�단락을�방지하기�위해�우선�와이어�

하네스를�빼�주십시오 .

• 본�기기에서�연기�또는�이상한�냄새가�나기�시작

하면�즉시�전원을�끄고�Kenwood�판매점에�상의

해�주십시오 .

• 페이스�플레이트와�기기�사이에�손가락이�끼어있

지�않은�것을�확인해��주십시오 .

• 표준�기기의�나사만을�사용하고�다른�나사를�사용

하지��마십시오 . 적당하지�않은�나사를�사용하면�

본�기기가�고장나는�경우가�있습니다．

• 본�기기를�떨어뜨리는�등�강한�충격을�주지�않도

록�주의해�주십시오 .

• 충격으로인해�LCD 가�손상되거나�망가졌을�경우

에는�액정�표시�액체를�만지지�마십시오 .��액정�

표시�액체는�건강에�좋지않거나�치명적일�수도�있

습니다 .

LCD 로부터의�액정�표시�액체가�몸이나�옷에�뭍

었을�경우에는�비누로�즉시�씻어내�주십시오 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

안전상의�주의

이�제품에�연결된�CD�플레이어 / 디스크�체인

저�정보

1998 년� 이후에� 출시된� KENWOOD� 디스크� 체인

저 /CD�플레이어는�이�제품에�연결할�수�있습니다 .

주

• 설치중에�문제가�발생할�경우에는�KENWOOD�

판매점에�상의해�주십시오 .

• 장치가�정상적으로�작동하지�않으면�재설정�단추

를�누릅니다 .�재설정�단추를�누르면�장치는�공장�

출하�시�기본�설정으로�돌아갑니다 .��재설정�단

추를�눌러도�장치가�정상적으로�작동하지�않으면�

해당�지역�KENWOOD�대리점에�문의하십시오 .

• 디스크�오디오�체인저가�제대로�작동되지�않으면�

리셋�버튼을�누르십시오 .��정상적인�작동으로�되

돌아옵니다 .

연결하여�사용할�수�있는�디스크�체인저/CD�플레이

어를� 확인하려면� 카탈로그를� 참조하거나� Kenwood�

판매업체에�문의하십시오 .

1997 년� 이전에� 출시된� KENWOOD� 디스크� 체인

저 /CD� 플레이어� 및� 다른� 제조업체에서� 만든� 디스

크�체인저는�이�제품에�연결할�수�없습니다 .�연결하

려고�하면�장치가�손상될�수�있습니다 .

연결�가능한�KENWOOD�디스크�체인저 /CD�플레

이어의�경우“O-N”스위치를“N”위치로�설정합니다 .

사용할�수�있는�기능�및�표시할�수�있는�정보는�연

결되는�제품�모델에�따라�다릅니다 .

• 잘못�연결했을�경우에는�본�기기와�CD�모두가�상할�

수�있습니다 .

리셋�버튼

• LCD 의�문자는�화씨�41 도�( 섭씨�5 도 )�이하에

서는�읽기�어려울�수도�있습니다 .�

• 본�취급설명서에�기재되어�있는�디스플레이부�및�

패널의�표기는�조작설명을�원활하게�하기�위한�표

시예입니다 .�따라서�실제의�기기와�다른�경우�및�

실제로는�있을�수�없는�표시�패턴이�기재되어�있

는�경우가�있습니다 .

렌즈의�흐림

추운� 동절기에� 자동차의� 히터를� 켜면� 본� 기기� CD�

플레이어의� � 렌즈에� � 결로가� 발생하여� 흐려지는� 경

우가�있습니다 . 이것을�렌즈의�흐림이라고�하며�CD

를� 재생할� 수� 없게� 되는� 경우가� 있습니다 . 이런� 경

우에는�디스크를�빼고�흐림이�사라질�때까지�기다려

주십시오 . 시간이� 조금� 지나도� 정상으로� � 작동하지�

않을� 경우에는� KENWOOD� 판매점에� 상의해� 주십

시오 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

주

카세트�테이프

기기의�손질

본�기기의�앞면�플레이트가�더러워졌을�때는�실리콘�

천과�같은�부드러운�마른�천으로�닦아�주십시오 .�

만약�앞면�플레이트의�오염물질이�떨어지지�않을�때

는�중성세제를�묻힌�천으로�오염물질을�닦아낸�후에�

마른�천으로�중성세제를�완전히�닦아내�주십시오 .

테이프�헤드의�청소

테이프가� 재생되어질� 때에� 노이즈가� 생기거나� 사운

드의�질이�떨어질�경우에는 ,�테이프�헤드의�오염이�

그�원인이�될�수�있으니 ,�테이프�헤드를�청소하십시

오 .

카세트�테이프

• 테이프가�느슨해�있을�경우에는�단단히�조이십시

오 .

• 카세트�테이프의�라벨이�떨어졌을�경우에는�라벨

을�다시�붙여주십시오 .

• 변형된�카셋트�테이프를�사용하지�마십시오 .

• 스프레이� 크리너를� 본� 기기에� 직접� 분사하여� 사용하

면�부품에�영향을�미칠�수�있습니다 . 거친�천�및�시너

나� 벤진� 등과� 같은� 휘발성� 액체를� 사용하여� 앞면� 플

레이트를� 닦으면� 표면에� 긁힘이� 생기거나� 인쇄된� 문

자가�지워지는�경우가�있습니다 .

• 카세트�테이프를�계기판�등�고열의�장소에�놓아두

지�마십시오 .

• 100 분�이상의�카세트�테이프를�사용하지�마십시

오 .

CD�슬롯의�손질

먼지가�CD�슬롯에�쌓이기�쉬우므로�가끔�청소를�해

주십시오 . 먼지가� � 부착된� CD� 슬롯에� CD 를� 넣으

면�CD 가�손상되는�경우가�있습니다 .

레이저에�의한�제품�마킹

（일부�지역을�제외）

CLASS 1

LASER PRODUCT

상기의� 라벨이� 샤시 / 케이스에� 붙어� 있으며，이� 구

성�부분은�레이저�광선을�사용하고�있고�클래스 1 로

구분� 되어� 있음을� 가리키고� 있습니다．다시� 말하면�

본� 기기는� 약한� 수준의� 레이저� 광선을� 사용하고� 있

기�때문에�기기�밖에서는�방사선의�위험성이�없습니

다 .

WOW,�SRS 와�

록상표입니다 .

표시는�SRS�Labs,Inc. 의�듬

WOW�기술은�SRS�Labs,Inc. 의�라이센스하에�있

습니다 .

Dolby�Laboratories 의�허가를�받고�제조되었습니

다 .

돌

비 ,� "Dolby" 와� 더 블 D� 기

호

는� Dolby�

Laboratories�의�등록상표입니다 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3/WMA�재생의�주의점�(DPX-MP4070/DPX-MP4070B)

그러나� 사용� 가능한� MP3� 레코딩� 메디아와� 포맷은�

제한되어져�있음을�명시해�주십시오 .�MP3 를�녹음

• 윈도우즈�미디어�플레이어�9�또는�그�이상의�기

할� 경우에는� 다음과� 같은� 제한점에� 주의를� 기울여

능의�일부를�사용하는�경우�재생�모드를�사용할�

주십시오 .

수�없는�경우도�있습니다 .

사용�가능한�메디아

본� 기기에� 사용� 가능한� MP3� 레코딩� 메디아는

CD-ROM,�CD-R,�CD-RW 입니다 .

CD-RW 를�사용하실�경우에는�기능�부전을�방지하

화일과�폴더�이름의�입력

표시�가능한�ID3�태그는�ID3�버젼�1.x 입니다 .

문자�코드는�코드�리스트를�참조해�주십시오 .

기�위해�퀵�포맷�방식이�아닌 ,�풀�포맷을�이용하십

시오 .

사용�가능한�메디아�포맷

본� 기기에� 사용� 가능한� 메디아� 포맷은� 다음과� 같습

니다 .��점�(“.”) 과�3 문자의�확장자를�포함한�화

일� 이름으로� 사용할� 수� 있는� 최대� 문자수는� 괄호안

의�숫자와�같습니다 .�

• ISO�9660�레벨�1�(12�문자 )

• ISO�9660�레벨�2�(31�문자 )

• Joliet�(64�문자 ;�최대�32 자가�표시됩니다 )

• Romeo�(128�문자 ;�최대�64 자가�표시됩니다 )

• 긴�화일명�(200�문자 ;�64 문자까지�표시됩니다 )

• 폴더명에�사용할�수�있는�최대�문자수 :�64�

(Joliet;32 문자까지�표시됩니다 )

사용�가능한�문자의�리스트는�라이팅�소프트의�설명

서와� 아래의� 화일과� 폴더� 이름� 입력� 섹션을� 참고해�

주십시오 .�

화일과�폴더�이름의�입력

코드�리스트의�문자는�입력과�출력이�가능한�화일과

폴더의�이름뿐입니다 .�

이외의� 다른� 문자를� 기입한� 경우에는� 화일과� 폴더

이름이�바르게�표시되어지지�않습니다 .��그리고 ,�그�

이름들은�사용중인�CD�라이터에�따라�바르게�표시

되어지지�않을�경우도�있습니다 .��

본�기기에서�만들�수�있는�미디어는�다음과�같은�한

도를�갖습니다 :

기기는� MP3/WMA� 확장자 (.MP3/.WMA) 를� 가

진�MP3/WMA 만을�인식하고 ,�재생합니다 .�

• 디렉토리�레벨의�최대�수�:�8

• 폴더당�화일의�최대�수�:�255

• 폴더의�최대�수�:�50

• 코드� 리스트에� 수록되어져� 있지� 않는� 문자로� 입력된�

화일� 이름은� 가진� 화일은� 바르게� 재생되어지지� 않을�

경우도�있습니다 .�

• 화일과�폴더의�최대�수 :�512�

위의�포맷�이외의�것으로�쓰여진�MP3/WMA 는�잘�

재생되어지지�않고 ,�그�화일�이름과�폴더�이름이�적

절하게�표시되어지지�않을�가능성이�있습니다 .��

메디아에�화일을�쓰기

MP3/WMA� 데이터가� 들어있는� 메디아가� 로딩되

어질� 경우에는� 기기가� 메디아에� 있는� 모든� 데이터

를� 체크합니다 .� � 만약� 메디아에� 많은� 폴더 ,� 혹은

MP3/WMA 가� 아닌� 화일이� 많이� 들어있으면� 재생

하기까지�시간이�많이�걸립니다 .�

MP3/WMA�인코더�및�CD�작성기�설정

MP3�인코더를�사용하여�MP3�데이터의�오디오�데

이터를�압축할�때는�다음과�같이�설정하십시오 .

또한 ,�다음�MP3/WMA�화일로�이동하는데�시간이�

많이�걸릴�수도�있고 ,�화일�/�폴더�검색이�부드럽게

수행되지�않을�경우도�있습니다 .��

•비트�전송률 :

MP3:�8�–�320�kbps

WMA:�48�–�192�kbps

•표본�주파수 :

MP3:�

8,�11.025,�12,�16,�22.05,�24,�32,�

44.1,�48�kHz

이러한�메디아를�로딩하면 ,�스피커가�손상을�입어�시끄

러운�노이즈가�생길�수도�있습니다 .�

• MP3/WMA� 확장자를� 가진� 비� MP3/WMA� 화일

이� 포함되어져� 있는� 메디아를� 재생시키지� 마십시오 .�

WMA:�32,�44.1,�48�kHz

CD�작성기를�사용하여�최대�디스크�용량까지�MP3

를�녹음하는�경우�추가�쓰기�기능을�비활성화하십시

오 .�한�번에�빈�디스크의�최대�용량까지�녹음하려면

“디스크�단위”를�선택하십시오 .

MP3/WMA� 확 장 자 를� 가 지 고� 있 으 면 ,�

비

MP3/WMA 도�MP3/WMA�화일로�인식되어집니다 .�

• 비�MP3/WMA�화일이�포함되어져�있는�메디아를�재

생시키지�마십시오 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3/WMA�재생�순서

화일�검색�(File�Search)�이�재생중인�화일

¡$ 를�실행하고�있을�경우⋯⋯

재생 ,�폴더�검색 (Folder�Search),�화일�검색 (File�

Search),�폴터�선택 (Folder�Select) 을�각각�선택

했을�경우의�화일과�폴더는�CD�라이터에�의해�쓰여

진�순서대로�접근되어집니다 .

버튼의�조작 (현재의�화일�번호:¡$)

그렇기� 때문에� 실제로� 재생되어지는� 순서와� 예상

했던� 재생순서가� 일치하지� 않을� 경우도� 있습니다 .�

CD� 라이터에� 따라서는� 화일� 이름의� 처음부분에

“01”에서“99”사이의�재생�연속�번호가�들어있는�

CD-R 과� 같은� 메디아에� MP3/WMA 를� 넣어서� 재

생되는� MP3/WMA 의� 순서를� 설정할� 수도� 있습니

다 .

예를�들어�다음과�같은�폴더�/�화일�체계를�갖는�메

디아는�다음과�같이�폴더�검색 ,�화일�검색 ,�또는�폴

더�선택에�종속되어집니다 .

�버튼

¡$�화일의�처음  ¡#

¡%  ¡&

폴더�검색�(Folder�Search)�이�재생중인�화

일 ¡$ 를�실행하고�있을�경우⋯⋯

버튼의�조작 (현재의�폴더�번호:4)

AM�버튼

FM�버튼

3  2  1  8

메디아의�폴더�/�화일�체계의�예

5  6  7  8  1

폴더

��

화일

루트

폴더�선택�(Folder�Select)�이�폴더에서�폴

더로� 이동하기� 위해서� 재생중인� 화일 ¡$ 로

선택되어져�있을�경우⋯⋯

�

버튼의�조작 (현재의�폴더�번호:4)

�버튼

AM�버튼

FM�버튼

레벨�1

레벨�3

레벨�5

�

레벨�2

레벨�4

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

CD에�관해서

CD�손질

CDs 의�제거

본� 기기에서� 디스크를� 뺄때에는� 수평으로� 당기십시

오 .

• CD 의�레코딩�표면을�만지지마십시오 .

사용할�수�없는�디스크

•원형이�아닌�디스크는�사용할�수�없습니다 .

• CD-R�과�CD-RW 는�일반�음악�CD 보다�손상되

기�쉽습니다 .�각각의�페키지의�주의�사항을�읽은�

후에�CD-R�과�CD-RW 를�사용해주십시오 .

• CD 에�테이프�등을�붙이지�마십시오 .�또한�테이

프가�붙어있는�디스크를�사용하지�마십시오 .

크는�사용할�수�없습니다 .

새�CD�사용시

디스크� 중앙의� 구멍� 혹은� 원� 둘레에� 흉터가� 있으면�

볼펜�등으로�제거한�후에�사용하십시오 .

•이�제품은�

할�수�있습니다 .

이�표시가�없는�디스크는�제대로�재생되지�않을�

수�있습니다 .

표시가�있는�CD 만�재생

•미완성의�CD-R�이나�CD-RW 는�재생할�수�없

습니다 .�( 완성�과정에�대해서는 CD-R/CD-RW�

라이팅�소프트와�CD-R/CD-RW�레코더�설명서

를�참조하십시오 .)

거스

러미

거스러미

디스크�저장

•직사광선이�비추는�곳�( 시트�혹은�계기판 ) 이나�

온도가�높은�곳에�보관하지�마십시오 .

•케이스에�넣어서�보관하십시오 .

CD�악세사리

디스크�타입의�악세사리를�사용하지�마십시오 .

CD�청소

디스크� 중앙의� 구멍� 혹은� 원� 둘레에� 흉터가� 있으면�

볼펜�등으로�제거한�후에�사용하십시오 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

일반�기능

�

� � �

��

ATT�표시기

전원

볼륨

전원�켜기

[SRC]�버튼을�누르십시오 .

볼륨을�크게�하기

[

]�버튼을�누르십시오 .

전원�끄기

[SRC]�버튼을�1 초�이상�누르십시오 .

볼륨을�줄이기

[

∞

]�버튼을�누르십시오 .

소스의�선택

소음기

[SRC]�버튼을�누르십시오 .

볼륨을�빨리�줄이기 .

소스

튜너

테이프

표시

[ATT]�버튼을�누르십시오 .

버튼을�누를때마다�소음기는�꺼졌다�켜졌다�합니

다 .

소음기가� 켜져있을� 경우에는� "ATT" 표시기가� 깜

박거립니다 .

"TUNER"

"TAPE"

"CD"

"CD�CH"

"AUX"

외부�디스크�(옵션�부속품)

보조�입력

스탠바이�(

일루미네이션�모드

)

"STANDBY"

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

• *

²�

- 본�기기로부터�제어가�가능한�파워�앰프의�카

탈로그나�사용설명서를�참조해�주십시오 .��

- 앰프들�중에는�플랫에서�+18�dB 까

��품과�연결하면�비록“

Amp�Bass�+18”이�

• *

¹�

이�모드는�< 서브�우퍼�출력 >(82�페이지 ) 이�

일반�기능

오디오�컨트롤

• < 사전�출력의�변환 >(96 페이지 ) 가�"SWPRE�

SW" 로�설정된�경우�이�기능을�컨트롤할�수�있습

니다 .

오디어�컨트롤�모드로�들어갑니다

[AUD]�버튼을�1 초이상�누르십시오 .

“AUD�mode”표시되어집니다 .

변경하기�위해�오디오�항목을�선택합니다

[FM+]�혹은�[AM ]�버튼을�누르십시오.

버튼을� 누를� 때마다� 변경되어질� 수� 있는� 항목이

아래와�같이�변환되어집니다 .

TEL�뮤트

전화가�걸려오면�오디오�시스템이�자동으로�

뮤트�됩니다 .

3 오디오�항목을�변경합니다

전화가�걸려오면

“CALL”표시되어집니다 .�

[

]�혹은�[

]�버튼을�누르십시오 .

변경�항목

밸런스

페이더

표시

"BAL"

"FAD"

범위

오디오�시스템이�일시정지합니다 .

좌�15�—�우�15

후�15�—�전�15

–15�—�+15

통화하는�동안�오디오�듣기

[SRC]�버튼을�누르십시오 .

“CALL”표시가� 사라지고� 오디오� 시스템이� ON

으로�돌아옵니다 .

서브�우퍼�레벨*¹"SubW"

베이스�부스트�레 "AmpB"

벨*²

플랫/+6/+12/

+18(dB)

통화가�끝날�때

전화를�끊습니다 .

"CALL" 표시가� 사라지고� 오디오� 시스템이� ON

으로�되돌아�옵니다 .

중심�주파수�끌어 "AmpF"

올리기*²

정상�/�낮음

로�패스�필터*¹

"LPF"

Through/120/

80/50�Hz

볼륨�오프셋

"V-OFF"

–8�—�±0

SRS�WOW 선택

“SubW�On”으로�설정된�때에만�이용�가능합

니다 .

• 볼륨�오프셋 :�각�소스의�볼륨은�기본�볼륨과�다르

게�설정할�수�있습니다 .

화려한�중저음을�사운드에�추가해서�재생하고

3D 사운드�영역을�만들수�있습니다 .

WOW 선택�모드를�입력합니다 .

[WOW]�버튼을�누르십시오 .

“WOW�SEL”표시되어집니다 .�

��지�설정�가능한�제품과�플랫에서�+12�

��dB 까지만�설정�가능한�제품이�있습니다 .

��만약�플랫에서�+12 까지만�설정이�가능한�제

2 WOW 항목을�선택합니다 .

[WOW]�버튼을�누르십시오 .

버튼을�누를�때마다 ,�SRS�WOW 선택이�아래와�

같이�변경됩니다 :

��설정되어도�작동하지�않습니다 .

SRS�WOW

사운드�이미지를�한�단계�올리고�베이 "Low"

스와�사운드�영역을�조정합니다.

표시

4 오디오�컨트롤�모드에서�나옵니다

[AUD]�버튼을�누르십시오 .

사운드�이미지를�두�단계�올리고�베이 "High"

스와�사운드�영역을�조정합니다.

<SRS�WOW�컨트롤>�에서의�설정값 "User"

으로�변경합니다.

서브�우퍼�출력

서브�우퍼�출력�ON�또는�OFF 로�하기 .

SRS�WOW가�없는�일반�사운드로�되 "Off"

돌아�갑니다.

[AM ]�버튼을�1 초�이상�누르십시오 .

버튼을� 누를� 때마다� 서브� 우퍼� 출력이� ON� 또는

OFF 로�바뀝니다 .

• 3 초�동안�조작을�중지하면 ,�SRS�WOW 선택이�

닫힙니다 .

ON 일�때 ,�"SubW�On" 이�표시됩니다 .

• WOW:�TruBass,�FOCUS�그리고�SRS�3D 는�

모두�아래에�보여지는�값으로�설정됩니다 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

“EQ�EASY �혹은

다 .

“EQ�PRO”가�표시되어집니

< 이퀼라이저�모드 > 가“EASY �일�경우 ,�< 이

퀼라이저�컨트롤 > 에�선택되어져�있는�이퀼라

이저�타입의�효과를�변경 .

SRS�WOW SRS�FOCUS

SRS�TruBass SRS�3D

이퀼라이저�타입

락

댄스

재즈

표시

High

Low

Off

High

Low

Off

"Rock"

"Dance"

"Jazz"

팝

"Pops"

"Heavy"

"Soft"

"Sharp"

"Light"

"Natural"

헤비메털

소프트

샤프

라이트

내츄럴

SRS�WOW�컨트롤

SRS�WOW 의�각�기능을�개별적으로�조정합

니다 .

WOW 컨트롤�모드를�입력합니다 .

[WOW]�버튼을�1 초�이상�누르십시오 .

“WOW�CTRL”표시되어집니다 .�

•

“User”( 이용자 )�표시�: 값은�<PRO 에서�이퀼라

이저�타입의�변경>�(84�페이지)�에서�설정됩니다.

• 선택되어진�이퀼라이저�타입은�변경할�수�있습니

다 .

변경�항목은�< 이퀼라이저�모드 >�설정에�따라�다

릅니다 .�(96 페이지 ).�변경에�관한�상세한�내용

은�<EASY 에서�이퀼라이저�타입의�변경 >�(83 페

이지 )�혹은�<PRO 에서�이퀼라이저�타입의�변경 >�

(84�페이지 ) 을�참조하십시오 .�

2 조정할�WOW 항목을�선택합니다 .

[FM+]�혹은�[AM ]�버튼을�누르십시오.

버튼을�누를�때마다 ,�아래에�보여지는�것처럼�조

정할�수�있습니다 .

WOW 항목을�조정합니다 .

[

]�혹은�[

]�버튼을�누르십시오 .

이퀼라이저�컨트롤�모드에서�나오기

1 초�이상�[EQ]�버튼을�누르십시오 .

10 초� 동안� 작동이� 멈추면 ,� 그때� 이퀼라이저� 타

입이�저장되어고�이퀼라이저�컨트롤�모드가�자동

으로�커집니다 .

변경�항목

SRS�FOCUS설정 "FOCUS"

표시

범위

0(Off)/1(Low)/

2(High)

SRS�TruBass설정 "TB"

SRS�3D설정

Off/On

"SRS"

4 WOW 컨트롤�모드로부터�나갑니다 .

[WOW]�버튼을�누르십시오 .

EASY 에서�이퀼라이저�타입의�변경

• TruBass: 수퍼�베이스�사운드에대한�재생을�지원

합니다 .

• FOCUS:�가상으로�스피커의�수직�비율을�변경하

거나�사운드스케이프를�늘리거나�줄여서�사운드�

이미지를�조정합니다 .

1 이퀼라이저�타입을�선택하시려면�< 이퀼라이

저�컨트롤 >�(83 페이지 ) 을�참조하십시오 .

• SRS�3D:�내츄럴 3D 사운드�영역을�만듭니다 .

• SRS�3D 은�튜너�모드에서�설정할�수�없습니다 .

효과의�변경

[FM+]�혹은�[AM ]�버튼을�누르십시오.

버튼을� 누를때마다� 이퀼라이저의� 효과는� 다음과�

같이�변환되어집니다 .

이퀼라이저�컨트롤

음악의�타입에�따라�최상의�사운드�사전�설정�

셋팅을�기억시킬�수�있습니다 .

이퀼라이저�타입

표시

"Hi"

"Mid"

"Lo"

높게

중간

낮게

1 이퀼라이저�컨트롤�모드로�들어가기

[EQ]�버튼을�누르십시오 .

3 이퀼라이저�컨트롤�모드에서�나오기

1 초�이상�[EQ]�버튼을�누르십시오 .

10 초� 동안� 작동이� 멈추면 ,� 그때� 이퀼라이저� 타

입이�저장되어고�이퀼라이저�컨트롤�모드가�자동

으로�커집니다 .

2 이퀼라이저�타입을�선택하기

[EQ]�버튼을�누르십시오 .

버튼을�누를때마다�이퀼라이저�타입은�다음과�같

이�변환되어집니다 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

• 만약“

모드 >�(96�페이지 ) 를�참고해“

로�변환하십시오 .�

EQ�EASY”표시되어지면 ,�< 이퀄라이저�

EQ�PRO”모드

< 이퀄라이저�모드 > 가“PRO”경우 ,�< 이퀄

일반�기능

PRO 에서�이퀄라이저�타입의�변경

이퀄라이저�타입�변경의�메모리�사전�

설정

라이저�컨트롤 > 에�선택되어져�있는�이퀄라이

저�타입�효과의�변경 .

<PRO 에서�이퀄라이저�타입의�변경 > 은�사전

에�설정할�수�있습니다 .

이퀄라이저�타입을�선택하기�위해서는�< 이

1 이퀄라이저�타입을�변경하려면�<PRO 에서�

퀄라이저�컨트롤 >(83�페이지 ) 을�참고해�

이퀄라이저�타입의�변경 >(84�페이지 ) 을�

주십시오 .

참고하십시오 .

2 변경�항목을�선택합니다

변경치의�사전�설정

[FM+]�혹은�[AM ]�버튼을�누르십시오.

버튼을� 누를� 때마다� 변경� 가능한� 항목이� 다음과

같이�변환되어집니다 .

1 초�이상�[1]—[3]�버튼을�누르십시오 .

셋팅�치를�불러오기

1 이퀼라이저�컨트롤�모드로�들어갑니다

[EQ]�버튼을�누르십시오 .

“EQ�PRO”표시되어집니다 .

3 항목을�변경합니다

[

]�혹은�[

]�버튼을�누르십시오 .

변경�항목

표시

범위

베이스�센터�주 "BasF"

파수

60/70/80/100

혹은�150�Hz

베이스�레벨

"BasLV"

"BasQ"

–12�—�+12

1.00/1.25/

1.50/2.00

베이스�Q�인자

셋팅�치를�불러옵니다

[1]—[3]�버튼을�누르십시오 .

베이스�익스

텐드

"EXT"

ON/OFF

미들�센터�주

파수

"MidF"

0.5/1.0/1.5/

2.0�kHz

미들�레벨

미들�Q�인자

"MidLV"

"MidQ"

–12�—�+12

1.0/2.0

영화�선택

영화�표시�선택하기 .

트레블�센터�주 "TreF"

파수

10.0/12.5/

15.0/17.5�kHz

1 영화�선택�모드를�입력하십시오

[MOVIE]�버튼을�1 초�이상�누르십시오 .

“Movie”표시되어집니다 .

트레블�레벨

"TreLV"

–12�—�+12

• 베이스�Q�인자�셋팅�치에�따라서�베이스�센터�주

파수에�설정되어질�수�있는�주파수는�다음과�같이�

변환됩니다 .

영화를�선택하십시오

[MOVIE]�버튼을�누르십시오 .

버튼을� 누를� 때마다 ,� 아래와같이� 영화가� 변경됩

니다 :

베이스�Q�인자

1.00/1.25/1.50

2.00

베이스�센터�주파수

60/70/80/100

60/70/80/150

영화

표시

영화의�스캔

영화1

영화2

영화3

영화4

영화5

영화6

영화7

영화8

OFF

"MovieScn"

"Movie�1"

"Movie�2"

"Movie�3"

"Movie�4"

"Movie�5"

"Movie�6"

"Movie�7"

"Movie�8"

"MovieOff"

• 베이스�익스텐드가�ON 으로�설정되어져�있을�경

우에는 ,�저�주파수�반응은�20% 까지�확장되어집

니다 .

4 이퀼라이저�컨트롤�모드에서�나오기

1 초�이상�[EQ]�버튼을�누르십시오 .

10 초� 동안� 작동이� 멈추면 ,� 그때� 이퀼라이저� 타

입이�저장되어고�이퀼라이저�컨트롤�모드가�자동

으로�커집니다 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

보조�입력�소스에서

3 영화�선택�모드에서�나옵니다

[MOVIE]�버튼을�1 초�이상�누르십시오 .

조작을� 10 초동안� 중단하면 ,� 그� 때의� 영화가� 등

록되고�영화�선택�모드가�자동으로�닫힙니다 .

정보

보조�입력명

문자

시간

In�Standby�mode

디스플레이의�변환

정보

문자�&�그래픽

시간�&�그래픽

시간

표시되어지는�정보의�변환 .

[DISP]�버튼을�누르십시오 .

버튼을�누를�때마다�디스플레이는�다음과�같이�변

환되어집니다 .

• 디스크�타이틀 ,�트랙�타이틀 ,�노래�타이틀 ,�앨범

명 ,�또는�아티스트명이�없는�디스크를�재생중에�

디스크�타이틀 ,�트랙�타이틀 ,�노래�타이틀�&�아

티스트명 ,�또는�앨범명�&�아티스트명을�선택하면�

트랙�넘버와�재생�시간이�표시됩니다 .

튜너�소스에서

정보

주파수

방송국�이름�혹은�주파수

표시

"SNPS"

문자

시간

CD�&�외부�디스크�소스에서

정보

표시

트랙�번호�&�트랙�시간

디스크�이름

디스크�타이틀

트랙�타이틀

문자

"DNPS"

"D-Title"

"T-Title"

시간

MP3/WMA�소스에서�(DPX-MP4070/

DPX-MP4070B)

정보

표시

트랙�번호�&�트랙�시간

폴더�이름

화일�이름

"Folder"

"File"

노래�타이틀�&�아티스트�이름 "Title"

앨범�이름

문자

"Album"

시간

테이프�소스에서

정보

재생�사이드�&�테이프�카운터

문자

시간

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

일반�기능

일류미네이션�컬러�선택

이용자�일류미네이션�컬러�설정

디스플레이�컬러의�설정 .

RGB 를�조정함으로�일류미네이션�컬러를�임

의적으로�설정할�수�있습니다 .

일류미네이션�컬러�선택�모드로�들어갑니다

[COL]�버튼을�누르십시오 .

일류미네이션�컬러�선택�모드로�들어갑니다

[COL]�버튼을�누르십시오 .

“llumi”가�표시되어집니다 .

일류미네이션�컬러를�선택합니다

[COL]�버튼을�누르십시오 .

버튼을�누를�때마다�일류미네이션�컬러는�다음과�

변경�컬러를�선택합니다

[

]�혹은�[

]�버튼을�누르십시오 .

버튼을�누를�때마다�변경되어지는�컬러는�다음과�

같이�변환되어집니다 :

일류미네이션

표시

“Blue”“Mint”의�스캔 "V.Color"

변경�컬러

빨강

그린

표시

블루

"Blue"

“R”깜박거립니다.

“G”깜박거립니다.

“B”깜박거립니다.

마스�레드

화이트

라벤다

머스컷

핑크

"Mars�Red"

"White"

"Lavender"

"Muscat"

"Pink"

블루

컬러를�변경합니다

[FM+]�혹은�[AM ]�버튼을�누르십시오.

버튼을� 누를� 때마다� 컬러의� 강도가� 다음과� 같이

변환되어집니다 :

하늘색

라임

"Sky�Blue"

"Lime"

보라색

물색

"Violet"

"Aqua"

컬러의�강도

끔

표시

“X-0”

오렌지

민트

"Orange"

"Mint"

약하게

“X-1”

��

사용자�컬러

"RX/GX/BX"

어둡게

“X-4"

3 일류미네이션�컬러�선택�모드에서�나옵니다

[COL]�버튼을�1 초�이상�누르십시오 .

10 초� 이상� 작동이� 멈추면� 그때의� 일류미네이션

컬러로� 확정되어지고 ,� 일류미네이션� 컬러� 선택

모드가�자동으로�꺼집니다 .

•“User�Color”는�< 이용자�일류미네이션�컬러�설

정 >�(86�페이지 )�의�컬러�셋트를�불러내서�사용

하실�수�있습니다 .��

3 일류미네이션�컬러�선택�모드에서�나옵니다

[COL]�버튼을�1 초이상�누르십시오 .

10 초� 이상� 작동이� 멈추면� 그때의� 일류미네이션

컬러가� 등록되어지고 ,� 일류미네이션� 컬러� 선택

모드가�자동으로�꺼집니다 .

시간�조정

시간�표시를�선택합니다

[DISP]�버튼을�누르십시오 .

2 시간�조정�모드로�들어갑니다

[DISP]�버튼을�1 초�이상�누르십시오 .

‡ 표시기가�깜박거립니다 .

3 시간을�조정합니다

[FM+]�혹은�[AM ]�버튼을�누르십시오.

분을�조정합니다

[

]�혹은�[

]�버튼을�누르십시오 .

4 시간�조정�모드에서�나옵니다

[DISP]�버튼을�누르십시오 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

• 메모리�번호

-�FM�&�AM�:�30�방송국

-�내부�CD�플레이어�:�10�디스크

방송국�/�디스크의�이름�붙이기�

(SNPS�/�DNPS)

-�

외부�CD�체인저�/�플레이어�:�CD�체인저�/�플

레이어에�따라�다양합니다 .��CD�체인저�/�플레

이어�메뉴얼을�참고해주십시오 .

방송국 ,�혹은�CD 에�타이틀�붙이기 .

1 타이틀을�붙이고자�하는�방송국�/�CD 를�

• 방송국�/�CD 의�타이틀은�이전에�이름을�붙였던�

똑같은�작동으로�변경할�수�있습니다 .�

청취�/�재생합니다

• < 디스플레이의�변환 >(85 페이지 ) 을�참조해서�

“DNPS”또는“SNPS”를�선택합니다 .�

보조입력원�설정

이름�설정�모드로�들어갑니다

[NAME.S]�버튼을�2 초�이상�누르십시오 .

“Name�Set”표시되어집니다 .

본�기기가�보조입력원�모드일�때�설정하여�주

십시오 .

3 커서를�문자�입력�위치로�옮김니다

[4]�혹은�[¢]�버튼을�누르십시오 .

1 보조입력원�선택하기

[SRC]�버튼을�누르십시오 .

“AUX”표시를�선택합니다 .

문자�타입을�선택합니다

[

]�버튼을�누르십시오 .

버튼을�누를�때마다�문자�타입은�다음과�같이�변

환되어집니다 .�

2 보조입력원�지정�모드로�들어가기

[NAME.S]�버튼을�2 초�이상�누르십시오 .

“Name�Set”표시되어집니다 .

표시

"A"

"a"

문자�타입

알파벳�오름�순

알파벳�내림�순

3 보조입력원�선택하기

[

]�혹은�[

]�버튼을�누르십시오 .

버튼을�누르면�아래에�나온�순서대로�입력원의�이

름이�표시됩니다 .

•“AUX”

•“TV”

5 문자를�선택합니다

[FM]�혹은�[AM]�버튼을�누르십시오 .

•“VIDEO”

•“GAME”

•“PORTABLE”

•“DVD”

• 번호�버튼이�달린�리모콘을�이용해서�문자를�입력

할�수�있습니다 .

예�:“DANCE”입력하고�싶으면

문자

"D"

"A"

"N"

"C"

"E"

버튼

[3]

[2]

[6]

[2]

[3]

누르는�횟수

4 보조입력원�지정�모드�끝내기

[NAME.S]�버튼을�누르십시오 .

• 작업이�10�초간�중단되면�현재�표시된�이름이�선

택되고�보조입력원�지정�모드를�종료합니다 .��

• 보조�입력�디스플레이는�내장의�보조�입력�또는�광

학�KCA-S210A 의�보조�입력을�사용할�때에만�설

정할�수�있습니다 .

스텝�3 에서�5 를�반복해서�이름을�입력합

니다 .

• 배터리로부터�본�유닛을�떼어내면 ,�보조�입력�이

름은“AUX”돌아갑니다 .

7 이름�설정�모드에서�나옵니다

[NAME.S]�버튼을�누르십시오 .

• 10 초�동안�작동이�멈추면 ,�그때의�이름이�등록되

어지고 ,�이름�설정�모드가�끝납니다 .��

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

튜너�기능

��

� � �

�

��

�

사전설정�방송국�번호

AUTO�표시기

밴드�디스플레이

주파수�표시

ST�표시기

리모트�기능

다이렉트�액세스�튜닝

튜닝

방송국의�선택 .

주파수와�튜닝의�입력 .

튜너�소스를�선택합니다

[SRC]�버튼을�누르십시오 .

“TUNER”표시를�선택합니다 .

밴드를�선택합니다

[FM]�혹은�[AM]�버튼을�누르십시오 .

2 다이렉트�액세스�튜닝�모드로�들어갑니다

리모콘으로�[DIRECT] 를�누르십시오 .

“-�-�-�-”가�표시되어집니다 .

밴드를�선택합니다

[FM+]�혹은�[AM ]�버튼을�누르십시오.

[FM+]�버튼을�누를때마다�밴드는�FM1,�FM2,�

FM3�밴드�사이에서�변환되어집니다 .

주파수를�입력합니다

리모콘으로�번호�버튼을�누르십시오 .

예�:

밴드를�위아래로�조정합니다

[

]�혹은�[

]�버튼을�누르십시오 .

원하는�주파수

92.1�MHz�(FM)

810�kHz�(AM)

누르는�버튼

[9],�[2],�[1]

[8],�[1],�[0]

• 스테레오�방송국의�청취중에는“ST”표시기가�켜

집니다 .

다이렉트�액세스�튜닝의�취소

리모콘으로�[DIRECT]�버튼을�누르십시오.

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

방송국�사전�설정�메모리

사전�설정�튜닝

메모리에�방송국을�등록 .

메모리로부터�방송국을�호출 .

밴드를�선택합니다

[FM+]�혹은�[AM ]�버튼을�누르십시오.

2 메모리에�넣을�주파수를�선택합니다

[

]�혹은�[

]�버튼을�누르십시오 .

2 방송국을�호출합니다

[1]—[6]�버튼을�누르십시오 .

3 메모리에�주파수를�넣습니다

2 초이상�[1]—[6] 버튼을�누르십시오 .

사전�설정�표시가�한번�깜박거립니다 .

각각의� 밴드에서� 메모리에� 한� 개의� 방송국이�

[1]—[6]�버튼으로�입력되어�질�수�있습니다 .�

주파수�스텝�설정

튜닝�주파수�스텝의�변경 .

오리지널�설정은�FM�밴드�50kHz 와�AM�밴

드�9kHz 입니다 .

1 전원을�끕니다

자동�메모리�등록

[SRC]�버튼을�1 초�이상�누르십시오 .

청취가�잘�되는�방송국을�메모리에�자동적으

로�등록 .

2 주파수�스텝을�변환합니다

[1] 과�[5]�버튼을�누르면서�[SRC]�버튼

을�누르십시오 .

주파수� 스텝은 FM� 밴드� 200kHz 와� AM� 밴드

1 자동�메모리�등록을�위한�밴드를�선택합니

다

10kHz 으로�변환되어집니다 .

[FM+]�혹은�[AM ]�버튼을�누르십시오.

2 메뉴�모드로�들어갑니다

[FNC]�버튼을�1 초�이상�누르십시오 .

“Function”가�표시되어집니다 .

• 같은�작동이�반복되어질�경우에는�오리지널의�설

정으로�되돌아갑니다 .

• 주파수�스텝이�변경되어질�경우에는�메모리에�있

는�주파수는�삭제되어집니다 .

3 자동�메모리�등록�모드를�선택합니다

[FM+]�혹은�[AM ]�버튼을�누르십시오.

“A-Memory”표시를�선택하십시오 .

자동�메모리�등록을�엽니다

[

]�혹은�[

]�버튼을�2 초�이상�누르

십시오 .

청취� 가능한� 6 개의� 방송국이� 메모리에� 등록되어

지면 ,�자동�메모리�등록은�자동으로�꺼집니다 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

카세트�플레이어�기능

�

� ��

��

�

��

�표시기

반복�표시기

블랭크�스킵�표시기

�표시기

돌비�B�NR�표시기

MTL�표시기

테이프�카운터�표시

카세트�테잎의�재생

돌비�B�NR

[B�NR]�버튼을�누르십시오 .

버튼을� 누를� 때마다� 돌비� B� NR 가� 켜졌다� 커졌

다�합니다 .

돌비� B� NR 가� 켜져있을� 경우에는“B� NR� On”

표시되어집니다 .

카세트�테잎이�들어있는�경우

[SRC]�버튼을�누르십시오 .

“TAPE”표시를�선택하십시오 .

• 카셋트�테잎이�들어있는�경우에는

켜집니다 .

�표시기가�

반대편을�듣고�싶을�경우

[

]�버튼을�누르십시오 .

테잎�타입의�선택

[MTL]�버튼을�누르십시오 .

버튼을�누를�때마다�테잎�타입이�다음과�같이�변

환되어집니다 .

카셋트를�빼십시오

[

]�버튼을�누르십시오 .

표시

테잎�타입

CrO₂�(타입�II),�FeCr�(타입� "MTL�On"

III),�Metal�(타입�IV)

빨리�감기와�되감기

Normal�(타입�I)

"MTL�Off"

빨리�감기

[FM+]�버튼을�누르십시오 .

[

]�버튼을�누르면�빨리�감기가�끝납니다 .

되감기

[AM ]�버튼을�누르십시오 .

[

]�버튼을�누르면�빨리�감기가�끝납니다 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

DPSS�( 다이렉트�프로그램�검색�시스

템 )

블랭크의�건너뛰기

녹음되어�있지�않은�부분이�10 초�이상�계속�

되어지면 ,�자동으로�빨리�감기가�됩니다 .

건너뛰기 ,�빨리�감기 ,�혹은�되감기하는�노래

의�표시 .

[B.S]�버튼을�누르십시오 .

버튼을�누를�때마다�블랭크�건너뛰기가�켜졌다�꺼

졌다�합니다 .

다음�노래로�건너뜀

[

�버튼을�누르십시오 .

]

블랭크� 건너뛰기가� 켜져� 있을� 경우에는“B.S�

On”표시되어집니다 .

버튼을�누를�때마다�건너뛰어지는�노래의�수가�늘

어납니다 .

전의�노래로�건너뜀

[

]�버튼을�누르십시오 .

버튼을�누를�때마다�건너뛰어지는�노래의�수가�늘

어납니다 .

색인�스캔

듣고�있는�테잎의�각곡의�처음�부분의�재생과�

듣고�싶은�노래의�검색 .

DPSS 의�취소

[

]�버튼을�누르십시오 .

색인�스캔을�시작합니다

[SCN]�버튼을�누르십시오 .

“IDX�SCAN”표시되어집니다 .

• 곡의�처음�5 초�동안에는�이전의�노래가�현재의�곡

으로�인식되어지는�경우도�있을�수�있습니다 .��

• 아홉�곡까지�건너뛸�수�있습니다 .

2 듣고�싶은�노래가�재생되어지면�이것을�놓

으십시오

[SCN]�버튼을�누르십시오 .

리모콘을�이용한�DPSS

음악의�반복

리모콘의�번호�버튼을�이용해서�건너뛸�수�있

는�노래의�지정 .

현재�듣고�있는�노래의�반복 .

[REP]�버튼을�누르십시오 .

버튼을�누를�때마다�음악�반복�(Music�Repeat)

가�켜졌다�꺼졌다�합니다 .

본�작동이�켜져�있을�때는“Repeat”표시되어집

니다 .

1 건너뛸�노래를�지정합니다

리모콘의�번호�버튼을�누르십시오 .

2 다음�노래로�건너뜁니다

[

�버튼을�누르십시오 .

]

전의�노래로�건너뜁니다

[

]�버튼을�누르십시오 .

DPSS 의�취소

[

]�버튼을�누르십시오 .

• 곡의�처음�5 초�동안에는�이전의�노래가�현재의�곡

으로�인식되어지는�경우도�있을�수�있습니다 .��

• 아홉�곡까지�건너뛸�수�있습니다 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/MD/MP3/WMA외부�디스크�컨트롤�기능

�

��

�

��

/M.RDM�표시기

트랙�시간

트랙�번호

SCN�표시기

REP/D.REP�표시기

CH�표시기

디스크�번호

�표시기

WMA/MP3�표시기

CD�&�MP3/WMA�재생

• 8cm�(3 인치 )�CD 에�어댑터를�부착하지�마십시

오 .�8cm�CD 를�어댑터로�본�기기에�삽입하면�손

상을�줄�수�있습니다 .

디스크가�들어있는�경우

[SRC]�버튼을�누르십시오 .

“CD”표시를�선택하십시오 .

• 본�기기에서�재생�가능한�MP3/WMA�메디아는�

CD-ROM,�CD-R,�CD-RW 입니다 .

• 디스크가�들어있는�경우에는

다 .

• MP3/WMA 를�재생할�수�있는�모델은�다음과�같

습니다 .

DPX-MP4070/DPX-MP4070B

• MP3 가�재생되어지는�동안에는“MP3”표시기가�

켜집니다 .�

�표시기가�켜집니

메디아의�포멧은�반드시�ISO9660�레벨�1,�레

벨�2,�Joliet,�혹은�Romeo�이어야합니다 .�

MP3/WMA�데이터�입력에�대한�방법과�사전�주

의�사항은�<MP3/WMA�재생의�주의점 >�(78 페

이지 ) 에�실려져있습니다 .�MP3/WMA�메디아를�

만드시기�전에�그�부분을�꼭�체크해�주십시오 .

• WMA 가�재생되어지는�동안에는“WMA”표시기

가�켜집니다 .�

일시�정지와�재생

외부�디스크의�재생

[

]�버튼을�누르십시오 .

버튼을�누를�때마다�일시�정지되었다�재생되었다�

합니다 .

본�기기에�접속되어져�있는�옵션�악세사리�디

스크�플레이어에서의�디스크�셋트의�재생 .

[SRC]�버튼을�누르십시오 .

디스크의�제거

[

]�버튼을�누르십시오 .

원하시는� 디스크� 플레이어용� 표시를� 선택하십시

오 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

표시�예�:

리모트의�기능

다이렉트�트랙�/�파일�검색

표시

"CD�CH"

디스크�플레이어

CD�체인저

트랙�번호�입력으로�트랙�/�파일�검색 .

"MD�CH"

MD�체인저

트랙�번호를�입력합니다

일시�정지와�재생

리모콘의�번호�버튼을�누르십시오 .

[

]�버튼을�누르십시오 .

버튼을� 누를때마다� 일시� 정지되었다� 재생되었다�

합니다 .

2 트랙�/�파일�검색을�합니다

[

]�혹은�[

]�버튼을�누르십시오 .

다이렉트�트랙�/�파일�검색의�취소

[

]�버튼을�누르십시오 .

• 디스크�#10 은“0”으로�표시되어집니다 .

• 사용할�수�있는�기능과�표시되어질�수�있는�정보는�

연결되어져�있는�외부�디스크�플레이어에�따라�달

라집니다

리모콘이�있는�디스크�체인저의�기능

다이렉트�디스크�검색

디스크�번호�입력으로�데스크�검색 .

빨리�감기와�되감기

1 디스크�번호를�입력합니다

리모큰의�번호�버튼을�누르십시오 .

빨리�감기

[

]�버튼을�계속�누르십시오 .

디스크를� 연주하는� 시점에서� 손가락을� 놓으십시

오 .

디스크�검색을�합니다

[DISC ]�혹은�[DISC+]�버튼을�누르십

시오 .

되감기

다이렉트�디스크�검색의�취소

[

]�버튼을�누르십시오 .

[

]�버튼을�계속�누르십시오 .

디스크를� 연주하는� 시점에서� 손가락을� 놓으십시

오 .

• 디스크�10 을�선택하시려면“0”입력하십시오 .

트랙�/�디스크�/�폴더�/�화일�반복

트랙�/�화일�검색

듣고�있는�디스크�체인저�혹은 MP3/WMA�

폴더에�있는�노래와�디스크의�재재생 .

MP3/WMA�폴더 ,�혹은�디스크에서의�노래�

선택 .

[REP]�버튼을�누르십시오 .

버튼을�누를�때마다�반복�재생은�다음과�같이�변

환되어집니다 .

[

]�혹은�[

]�버튼을�누르십시오 .

CD�/MD�재생�중�

디스트�체인저 /�MP3/�WMA 의�기능

디스크�검색 / 폴더�검색

반복�재생

트랙�반복

표시

"Repeat"

디스크�반복(디스크� "D-Repeat"

체인저의�기능)

MP3/WMA 메디아에�녹음된�폴더�또는�디스

크�체인저에서의�디스크�설정�선택하기

OFF

[AM ]�혹은�[FM+]�버튼을�누르십시오.

MP3/WMA 재생�중

반복�재생

화일�반복

폴더�반복

OFF

표시

"File�REP"

"Fold.REP"

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

• 폴더�선택�모드에서�다른�폴더로�이동하는�방

법은�폴더�검색�모드에서의�방법과�다릅니다 .�

<MP3/WMA�재생의�주의점 >�(78�페이지 )�을�참

고해주십시오 .

• [¢]�버튼을�누르면�다음�선택�곡이�시작됩니다 .�

• [¢]�버튼을�누르면�다음�선택�곡이�시작됩니다 .

CD/MD/MP3/WMA외부�디스크�컨트롤�기능

DPX-MP4070/DPX-MP4070B�기능

트랙�스캔

MP3/WMA�기능

듣고�있는�디스크 ,�혹은�MP3/WMA 의�각

곡의�처음�부분의�재생과�듣고자�하는�노래의�

검색 .

폴더�선택

듣고자�하는�폴더의�빠른�선택 .

폴더�선택�모드로�들어갑니다

[F.SEL]�버튼을�누르십시오 .

선택 (select)� 모드에서는� 폴더의� 정보가� 다음과�

같이�표시되어집니다 .

트랙�스켄을�시작합니다

[SCN]�버튼을�누르십시오 .

“Scan”표시되어집니다 .

폴더�이름�표시

현재의�폴더�이름의�표시

듣고자�하는�노래가�재생되어지면�이것을�

놓습니다

[SCN]�버튼을�누르십시오 .

KENWOOD

폴더�레벨을�선택합니다

랜덤�재생

[FM+]�혹은�[AM ]�버튼을�누르십시오.

[FM+]�버튼으로�1 레벨�아래로�내리고 ,��

[AM ]�버튼으로�1�레벨�위로�올리십시오 .

디스크�혹은�MP3/WMA�폴더에�있는�모든�

노래를�랜덤으로�재생 .

[RDM]�버튼을�누르십시오 .

버튼을� 누를� 때마다� 랜덤� 재생이� 켜졌다� 꺼졌다

합니다 .

랜덤� 재생이� 켜져� 있을� 경우에는“Random”표

시되어집니다 .

같은�레벨에서�폴더의�선택합니다

[

]�혹은�[

]�버튼을�누르십시오 .

[

]�버튼으로�앞의�폴더로�이동하고 ,�[

]�

버튼으로�다음�폴더로�이동하십시오 .

톱�레벨로�돌아옵니다

[3]�버튼을�누르십시오 .

재생할�폴더를�결정합니다

[

]�버튼을�누르십시오 .

폴더�선택�모드에서�나오면 ,�표시되어진�폴더�내

에�있는�MP3/WMA 가�재생되어집니다 .

디스크�체인저의�기능

매거진�랜덤�재생

디스크�체인저에�있는�모든�디스크의�노래를�

랜덤으로�재생 .

[M.RDM]�버튼을�누르십시오 .

버튼을� 누를� 때마다� 매거진� 랜덤� 재생이� 켜졌다

꺼졌다�합니다 .

폴더�선택�모드의�취소

매 거 진� 랜 덤� 재 생 이� 켜 져� 있 을� 경 우 에 는

“M-Random”표시되어집니다 .

[F.SEL]�버튼을�누르십시오 .

텍스트�/�타이틀�화면�이동�(scroll)

표시되어진�CD�텍스트 ,�MP3/WMA�텍스

트 ,�혹은�MD�타이틀의�화면�이동 .

[SCRL]�버튼을�누르십시오 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

기능�설정

��

� � �

��

�

기능�설정

4 기능�설정�모드에서�나옵니다

[FNC]�버튼을�누르십시오 .

빕�(beep)�사운드�등의�기능이�작동�중�일�경

우의�설정 .

• 위의�기본�작동�방법에�적용할�수�있는�다

른�항목이�표시될�경우에는�설정�내용�차트

가�뒤에�입력되어집니다 .�( 일반적으로�차트

의�가장�위에�있는�설정이�오리지널입니다 .)

또한 ,�적용되지�못하는�항목에�대한�설명은�단계

별로�입력되어집니다 .

기능�설정의�기본적인�작동�방법은�이곳에�설

명되어져�있습니다 .�기능�항목과�설정�내용에�

관한�내용은�본�작동의�설명�후에�나옵니다 .

기능�설정�모드로�들어갑니다

[FNC]�버튼을�1 초�이상�누르십시오 .

“Function”이�표시되어집니다 .

기능�설정�항목을�선택합니다

[FM+]�혹은�[AM ]�버튼을�누르십시오.

예� : 빕� 사운드로� 설정하고자� 할� 경우에는�

“BEEP”표시를�선택하십시오 .

3 기능�설정�항목을�설정합니다

[

]�혹은�[

]�버튼을�누르십시오 .

예� :“BEEP”선택되어져� 있을� 경우에는� 버튼

을�누를�때마다“

BEEP�On”혹은“BEEP�

Off”변환되어집니다 .� 이� 둘� 중의� 하나로�

설정하십시오 .

스텝� 2 로� 돌아가서� 다른� 항목을� 설정하실� 수도�

있습니다 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

기능�설정

스탠바이�모드에서

일류미네이션�컬러�모드

사전�출력의�변환

디스플레이의�일류미네이션�컬러�모드의�셋

팅 .

후면과�서브�우퍼�사이의�프리아웃�변환하기 .�

( 서브�우퍼에서�페이더�컨트롤로부터의�효과

없이�출력합니다 .)�

표시

설정

표시

"SWPRE�R"

"SWPRE�SW"

설정

후반�사전�출력

서브�우퍼�프리아웃.

"COL�Sync"

볼륨�조절과�어테뉴에이터가�

On일�경우에�디스플레이의

컬러가�한가지�컬러에서�다른�

컬러로�변환됩니다.

"COL�Fix"

컬러�설정를�고정시킵니다.

스탠바이�모드에서

데모의�시작

스탠바이�모드에서

콘트라스트 ( 대비 )�조정

전원이�켜져�있을�경우의�데모의�설정 .

표시 설정

"Open�On" 전원이�켜져�있을�경우에�데모가�수

행되어집니다.�

디스플레이의�콘트라스트의�조정 .

표시와�설정

"CONT�1"

"Open�Off" 전원이�켜져�있을�경우에�데모가�수

행되어지지�않습니다.

"CONT�6"�(오리지널�설정)

��

"CONT�11"

스탠바이�모드에서

이퀄라이저�모드

이퀄라이저�타입�변경�방법의�설정 .

스탠바이�모드에서

터치�센서�톤�(tone)

표시

"EQ�EASY"

설정

이퀄라이저�타입의�효과가�3�레

벨�사이에서�변경�가능합니다.

작동�체크�사운드�( 빕�사운드 ) 의�ON/OFF�

설정 .

"EQ�PRO"

이퀄라이저�타입은�베이스,�미

들,�트레블에�의해�변경되어질�

수�있습니다.�

표시

"BEEP�On"

설정

빕이�들립니다.

"BEEP�Off"

빕이�취소되었습니다.

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

• 코드가�3 과�다르게�입력되어지면 ,�스텝�3 부터�다

시�반복하십시오 .

• 안전�코드�기능이�작동하고�있을�경우에는�코드가�

변환되어질�수�없고 ,�그�기능이�해제되어질�수도�

없습니다 .

스탠바이�모드에서

안전�코드

네비게이션�뮤트

이것이�매체로부터�제거되어질�때에�안전�코

드에�의한�공인이�요구되어지므로 ,�안전�코드

를�사용해�본�기기를�개인화하는�것은�데이터

의�도난을�방지하는데�도움이�됩니다 .

네비게이션�음성�안내�중�오디오�사운드를�음

소거합니다 .

표시

설정

"NavM�Off"

사운드를�음소거합니다.

"NavM�On"

사운드를�음소거하지�않습니다.

안전�코드는�원하시는�4 자리의�숫자로�설정할�수�

있습니다 .

스탠바이�모드에서

TEL�뮤트

안전�코드�모드를�선택합니다

[FM+]�혹은�[AM ]�버튼을�누르십시오.

“CODESTBY”표시를�선택하십시오 .

전화가�걸려오면�사운드를�뮤트로�설정할�수�

있습니다 .

안전�코드�모드로�들어갑니다

[COL]�버튼을�2 초�이상�누르십시오 .

“WRITE”표시되어진� 후에“CODE� ****”표시

되어집니다 .

표시

설정

"TelM�Off"

사운드를�음소거합니다.

안전�코드를�입력합니다

"TelM�On"

사운드를�음소거하지�않습니다.

[1]—[4]�버튼을�누르십시오 .

예�:�안전�코드가“3510”인�경우 .

스텝

버튼

[1]

[2]

[3]

[4]

#�누르는�횟수

표시

"3"

"5"

"1"

"0"

스탠바이�모드에서

내장�보조입력�설정

내장�보조입력�기능�설정하기 .

안전�코드를�확인합니다

표시

설정

[COL]�버튼을�누르십시오 .

"AUX�Off" 보조입력이�없는�소스를�선택했을�때.

"AUX�On" 보조입력이�있는�소스를�선택했을�때.

“WRITE”표시되어진�후에“1�CODE�****”표

시되어집니다 .

5 3 과�4�스텝의�작동을�한�후에�안전�코드를�

재입력합니다 .

안전�코드가�효력을�발휘합니다 .

스탠바이�모드에서

내장�앰프�설정

내장�앰프의�ON/OFF�설정 .�이�기능을�

OFF�하면�프리아웃의�질이�향상됩니다 .

재설정�버튼을�누르면�배터리�전원�소스로부

터�이것이�제거되어집니다

표시

"AmpM�Off"

설정

내장�앰프가�작동�중�입

니다.

전원을�켭니다 .

2 3 와�4�스텝을�밟아서�안전�코드를�입력합

"AmpM�On"

내장�앰프의�작동이�중단�되

었습니다.

니다 .

“CODE�OK!”가�표시되어집니다 .

기기가�사용되어질�수�있습니다 .

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

기능�설정

스탠바이�모드에서

튜너�모드에서

보안장치�표시

튜닝�모드

도난방지를�위해서�ACC�가�OFF�된�후에는�

기기상의�붉은�표시�등이�깜빡거립니다 .

튜닝�모드를�설정합니다 .

튜닝�모드 표시

작동

표시

"S.I�Off"

설정

LED�꺼짐.

자동�검색

"Auto�1"

방송국의�자동�검색

"S.I�On"

LED�깜빡임.

사전�설정�방 "Auto�2"

송국�검색

사전�설정�메모리의�

방송국�순으로의�검색

메뉴얼

"Manual" 일반�메뉴얼�튜닝�컨

트롤

DPX-MP4070/DPX-MP4070B�기능

스탠바이�모드에서

CD�읽기�설정

특수한�포멧으로�CD 를�재생하는�데에�문제

가�있는�경우 ,�이�설정은�CD 를�강제적으로�

재생합니다 .

FM�수신

모노럴�수신�

스테레오�방송이�모노럴로�수신되어질�경우에

는�노이즈가�생길�수도�있습니다 .

표시

설정

"CD�READ�1" CD와�MP3/WMA를�재생합

니다.

표시

"MONO�Off"

"MONO�On"

설정

모노럴�수신이�OFF

모노럴�수신이�ON

"CD�READ�2" CD를�강제적으로�재생합니다.

•

“CD�READ�2”로�설정하면�MP3/WMA 는�재생

할�수�없습니다 .

일부�음악�CD 은�"CD�READ�2" 모드에서도�재생

할�수�없을�수도�있습니다 .

튜너�모드에서

자동�메모리�등록

작동�방법은�< 자동�메모리�등록 >�(89�페이

지 ) 을�참고해�주십시오 .

CD/MP3/WMA 외부�디스크�컨트롤�모드에

서

텍스트�스크롤

표시된�텍스트�스크롤의�설정 .

표시

"SCL�Auto"

설정

스크롤의�반복

"SCL�Manu"

표시가�바뀌었을�때의�스크롤

• 스크롤�되어진�텍스트는�다음과�같이�보여집니다 .

-CD�텍스트

-�폴더�이름�/�파일�이름�/�곡명�/�아티스트�이름�/�

앨범�이름

-MD�타이틀

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

리모콘의�기본�조작

��

빈�공간

��

�

��

배터리의�삽입�및�교환

기본�작동

두개의�"AA"�사이즈�배터리를�사용합니다．

[VOL.]�버튼

그림과�같이�거버를�아래로�누르면서�밀어서�

커버를�엽니다．

볼륨을�조절합니다 .

[SRC]�버튼

그림과�같이�배터리의�＋극과�－극의�방향을�

확인하여�케이스�안으로��삽입합니다．

버튼을�누를�때마다�소스가�바뀝니다 .

소스� 변환� 순서에� 관해서는� < 소스의� 선택 >� (81

페이지 ) 를�참조해�주십시오 .

[ATT]�버튼

볼륨을�빨리�줄입니다 .

이�버튼을�다시�누르면 ,�볼륨은�이전의�상태로�돌

아옵니다 .

2 경고

• 사용하지�않은�배터리는�어린이의�손이�닿는�곳에�

보관하지�마십시오．잘못하여�배터리를�삼킨�경우

에는�즉시�의사의�진료를�받아�주십시오．

• 리모콘을�대시보드�등�온도가�높아지는�곳에�놓지�

마십시오．

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

리모콘의�기본�조작

튜너�소스에서

디스크�소스에서

[FM]/�[AM]�버튼

[

]/�[

]�버튼

밴드를�선택합니다 .

MP3/WMA� 폴더 ,� 혹은� 디스크에서의� 노래� 선

택 .

[FM]� 버튼을� 누를� 때마다� FM1,� FM2,� FM3�

밴드로�바뀝니다 .

[DISC+]/�[DISC-]�버튼

디스크�/�폴더를�앞뒤로�합니다 .

[

]/�[

]�버튼

밴드를�위�아래로�조절합니다 .

[

]�버튼

버튼을�누를�때마다�노래는�일시�정지되었다가�재

생되었다�합니다 .

[0]—[9]�버튼

사전� 설정� 방송국을� 불러오기� 위해서� [1]—[6]

버튼을�누릅니다 .

[0]—[9]�버튼

< 다이렉트�트랙�/�파일�검색 >�(93�페이지 ) 과�<

다이렉트�디스크�검색 >�(93�페이지 ) 에서�트랙�/�

디스크�번호를�입력합니다 .

[DIRECT]�버튼

< 다이렉트�액세스�튜닝 >(88�페이지 )�모드로�들

어가고 ,�그�모드를�취소합니다 .

카세트�테이프�소스에서

[

]/�[

]�버튼

<DPSS�( 다이렉트�프로그램�검색�시스템 )>�(91

페이지 )

[

]�버튼

테이프의�반대편을�재생합니다 .

[FM]�버튼

테이프를�빨리�감습니다 .

[

]�버튼을�누르면�빨리�감기가�끝납니다 .

[AM]�버튼

테이프를�되감습니다 .

[38]�버튼을�누르면�빨리�감기가�끝납니다 .

[0]—[9]�버튼

< 리모콘을� 이용한 DPSS>� (91� 페이지 ) 에서� 노

래의�번호를�입력합니다 .

100

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

부속품/�설치�순서

부속품

설치�순서

1.단락을�방지하기�위해�이그니션에서�키를�

빼고 -�배터리를�차단합니다．

2.각�기기의�입출력�와이어를�바르게�접속합

니다．

3.와이어링�하네스와�스피커�와이어를�접속합

니다．

4.어스，배터리，이그니션의�순서로�와이어링�

하네스의�와이어를�접속합니다．

5.와이어링�하네스�커넥터를�본�기기에�접속

합니다．

6.자동차에�본�기기를�설치합니다．

7.-�배터리를�다시�접속합니다．

8.리세트�버튼을�누릅니다．

..........1

..........6

2 경고

이그니션� 와이어� ( 빨강 ) 와� 배터리� 와이어� ( 노랑 )

를�차대�( 접지 ) 에�연결할�때에�전기�누전을�일으켜�

발화할�수도�있습니다 .�이들�와이어는�항상�휴즈�박

스를�관통하는�전원�소스에�연결하십시오 .

• 자동차의�이그니션에�ACC�위치가�없는�경우에는��이

그니션��키를��사용하여�ON/OFF 로�할�수�있는�전

원에� 이그니션� 와이어를� � 접속합니다 � 배터리� � 와이

어�처럼�일정�전압의�전원에�이그니션�와이어를�접속

하면�배터리가�움직이지�않습니다．

•콘솔에� 뚜껑이� 있는� 경우에는� 개폐시에� 보호� 덮개가

뚜겅에�접촉하지�않도록�장치를�설치하십시오 .

• 퓨즈가� 끊어졌을� 경우에는� 단락의� 원인이� 되므로� 와

이어가� � 접촉하고� 있지� 않음을� 확인하고� 나서� 같은

규격의�새�퓨즈로�교환해�주십시오．

• 연결되지�않은�와이어는�비닐�테이프�등으로�절연시키

십시오．누전을�방지하기�위해서�연결되지�않은�와이

어 ,�혹은�단자의�끝에�있는�캡을�제거하지�마십시오．

• 스피커�와이어를�해당�단자에�바르게�접속합니다 �-

와이어를�공유하거나�자동차의�금속부분에�어스를�연

결하면�본�기기가�고장이�나거나�오작동할�수도�있습

니다．

• 두개의�스피커가�시스템에�연결되어져�있을�경우에는�

출력�단자의�앞의�양쪽 ,�혹은�출력�단자의�후반의�양

쪽에�커넥터를�연결하십시오 �( 앞쪽과�후반부를�섞어

서�연결하지�마십시오．)�예를�들어 ,�왼쪽�스피커의�

+�커넥터를�앞쪽의�출력�단자에�연결했다면 , -�커

넥터를�후반�출력�단자에�연결하면�안됩니다．

• 본� 기기를� 설치한� 후에� 자동차의� 브레이크� 램프 � 점

멸기 �와이퍼가�정삭으로�작동하고�있는지�확인해�주

십시오．

• 설치� 각도가� 30 도� 이하로� 되도록� 본� 기기를� 설치해�

주십시오．

한글

101

Download from Www.Somanuals.com. All Manuals Search And Download.

와이어를�단자에�접속

AUX�좌�(left)�입력�( 흰색 )

AUX�우�(right)�입력�( 빨간색 )

앞�왼쪽�출력�( 흰색 )

뒤�왼쪽�출력�( 흰색 )/

서브�우퍼�왼쪽�출력 ( 흰색 )

앞�오른쪽�출력�

( 빨간색 )

뒤�오른쪽�출력�( 빨간색 )/

서브�우퍼�오른쪽�출력 ( 빨간색 )

M4�8mmMAX

FM/AM�안테나�입력

KENWOOD�디스크�체인저�컨트롤�입력

디스크�체인저�접속시에는�디스크�체인

저�매뉴얼을�참조

와이어링�하네스

( 부속품 1)

퓨즈�(10A)

만약�연결되지�않았으면�선이�탭으로부

터�삐져�나오지�않게�해�주십시오 .

사용하고�있는�안테나에�따라�모터�안테나�컨트롤단

자�또는�필름�타입��안테나의�부스터�증폭용�전원단

자에�접속한다 .

ANT. CONT

P.CONT

MUTE

모터�안테나�컨트롤�와이어�( 청색 )

전원�컨트롤�와이어 ( 청색 / 흰색 )

TEL�뮤트�와이어 ( 갈색 )

옵션의�앰프를�사용할�경우에�전원�컨트롤�단자에�

접속한다 .

전화가�오거나�통화�중일�때는�접지된�단자에�연결합니

다 .�KENWOOD�네비게이션�시스템에�연결하려면�네

비게이션�매뉴얼을�참고하십시오 .

자동차�라이트�컨트롤�스위치에

ILLUMI

조광기�컨트롤�와이어�

( 오랜지 / 흰색 )

외부�앰프�컨트롤�기능을�가지는�앰프의�

“EXT.AMP.CONT. �터미널에 .

EXT.CONT.

외부�앰프�컨트롤�와이어

( 핑크 / 검은색 )

흰색 / 검은색

흰색

앞�왼쪽�스피커

앞�오른쪽�스피커

뒤�왼쪽�스피커

회색 / 검은색

회색

녹색 / 검은색

녹색

보라색 / 검은색

보라색

뒤�오른쪽�스피커

자동차의

퓨즈�복스

이그니션�키�

스위치

이그니션�와이어�( 빨간색 )

배터리�와이어�( 황색 )

ACC

자동차의�퓨즈�복스�

( 메인�퓨즈 )

지선 ( 검은색 ) -�( 자동차의�새시에 )

배터리

�

102

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

설치

설치전에�CD 의�조작을�확인할�경우는�본�기기를�수

평으로�놓고�CD 의��삽입 / 꺼내기를�실행합니다．

설치

부속의�나사 (M5×6mm,�M5×7mm) 를�사용하여

블라켓에�설치합니다．사용하는�블라켓의�구멍은�자

동차�모델에�따라�다릅니다．

지선이�와이어링�킷트에�들어가�있을�경우（별도�판

매）는�본�기기의��뒷패널에�있는�접속공구를�사용하

여�지선을�단단히�조여�주십시오．

나사�(M4×8)

( 상용 )

부속 3

(M5×6mm)

또는�부속 4

(M5×7mm)

부속 2

( 닛산�자동차에�한함 )

• 설치할�때는�제공된�나사만�사용하십시오 .�다른�나사

를�사용하면�본체가�손상될�수�있습니다 .

• 설치할� 때� 스크류� 드라이버나� 유사한� 공구로� 심하게�

힘을�주면�손상될�수�있습니다 .

한글

103

Download from Www.Somanuals.com. All Manuals Search And Download.

트러블�처치�가이드

소리가�들리지�않습니다 .��/��음량이�너무�작습

니다 .

사소한�조작�실수나�배전�실수로�인하여�

기기가�기능하지�않는�경우가�있습니다．

서비스를�의뢰하기�전에�생각되는�문제

에�대하여�아래�표를�참조하여��확인해�

주십시오．



페이더 ,�혹은�밸런스�설정이�한쪽이�최고로�

설정되어져�있습니다 .



페이더 ,�혹은�밸런스�설정을�중앙으로�옮

기십시오 .



입력�/�출력 ,�혹은�와이어링�하네스가�적절

하게�접속되어져�있지�않습니다 .

일반



입력�/�출력 ,�혹은�와이어링�하네스를�바

르게�재접속하십시오 .�< 단자에�와이어를�

연결하기 >�를�참고해�주십시오 .

전원이�들어오지�않습니다 .



휴즈가�끊어져�있습니다 .



카세트�테이프이�좋지�않습니다 .�



와이어의�누전을�체크한�후에�같은�규격

의�새�휴즈로�교환하십시오 .



다른�카세트�테이프를�넣어보십시오 .��만

약 ,�잘�작동한다면�처음의�테이프가�좋지�

않은�것입니다 .



스피커�케이블이�섀시에�닿습니다 .



스피커�케이블�배선을�손보거나�절연한�

다음�재설정�단추를�누릅니다 .



볼륨�오프셋의�값이�낮습니다 .



< 오디오�컨트롤 >(82 페이지 )�섹션을�참

조해서�볼륨�오프셋을�올리십시오 .

변환할�수�없는�소스가�있습니다 .�



테잎이�들어있지�않습니다 .

< 내장�앰프�설정 >�( 페이지�97) 이�ON�상태

입니다 .



듣고자�하는�미디어를�셋트�시키십시오 .�

본�기기에�미디어가�들어있지�않으면�각�

소스로�변환할�수�없습니다 .



OFF�으로�전환 .

음질이�좋지�않습니다 .�/�음질에�이상이�있습니

다 .



디스크�체인저가�연결되어져�있지�않습니다 .



디스크�체인저를�연결하십시오 .�디스크�

체인저가�입력�단자에�연결되어�있지�않

으면 ,�외부�디스크�소스로�변환할�수�없

습니다 .



차량의�스피커�와이어가�나사로�조여져�있습

니다 .



스피커�와이어링을�체크하십시오 .

테이프의�헤드가�더러워져�있습니다 .

테이프의�헤드를�청소하십시오 .

스피커가�바르게�배선되어져�있지�않습니다 .



이그니션�장치가�꺼질�때�메모리가�삭제되어집니

다 .





이그니션�장치와�배터리�와이어가�바르게�연

결되어져�있지�않습니다 .



각�출력�단자가�다른�스피커에�접속되도

록�스피커를��재접속하십시오 .



< 단자에�와이어를�연결하기 >�를�참고해

서�와이어를�바르게�연결하십시오 .

터치�센서�톤 (tone) 이�소리가�나지�않습니다 .



사전�출력�잭이�사용되어지고�있습니다 .

TEL 뮤트�기능이�작동하지�않습니다 .



터치�센서�톤은�사전�출력�잭에서는�출력

되어지지�않습니다 .



TEL 뮤트�배선이�올바르게�연결되지�않았습

니다 .

디머�기능이�작동하지�않습니다 .



< 터미널에�접속�배선�연결하기 >�섹션을�

참조해서�배선을�올바르게�연결하십시오 .



디머�배선이�올바르게�연결되어�있지�않습니

다 .



<TEL�뮤트 >�( 페이지�97) 이�OFF�상태입

니다 .



디머�배선�연결을�확인하십시오 .



ON�으로�전환 .

TEL 뮤트�배선이�연결되지�않았더라도�TEL 뮤

트�기능은�ON 으로�됩니다 .



TEL 뮤트�배선이�자동차의�금속�부분에�접촉

하고�있습니다 .



TEL 뮤트�배선을�자동차의�금속�부분으

로부터�떼어내�주십시오 .

104

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

튜너�소스

디스크�소스

라디오의�수신이�좋지않습니다 .

외부�디스크�컨트롤�모드가�수행되어지지�않은채

“AUX�EXT”가�표시되어집니다 .



차의�안테나가�뽑혀져�있지�않습니다 .

안테나를�끝까지�빼주십시오 .





지원되지�않는�디스크�체인저가�연결되어져�

있습니다 .



안테나�컨트롤�와이어가�접속되어져�있지�않

습니다 .



< 안전상의�주의 >�섹션의�< 이�제품에�연

결된�CD 플레이어 / 디스크�체인저�정보 >

(76 페이지 ) 에�언급된�디스크�체인저를�

사용하십시오 .



< 단자에�와이어를�연결하기 >�(102�페이

지 ) 를�참고해 ,�와이어를�바르게�연결하

십시오 .

어떤�디스크는�재생되어지고 ,�또�어떤�디스크는�

재생되어지지�않습니다 .

다이렉트�액세스�튜닝을�이용해�원하는�주파수가�

입력되어지지�않습니다 .



재생되어지지�않는�어떤�CD 는�더러워져�있

습니다 .



수신�불가능한�방송국이�입력되어졌습니다 .

수신�가능한�방송국을�입력해�주십시오 .

0.01MHz�기기로�주파수를�입력하고�있습니



CD 를�청소하십시오 .



다 .



재생되어지지�않는�디스켓이�다른�슬롯에�들

어있습니다 .�



FM�밴드에�지정할�수�있는�것은�0.1�

MHz 입니다 .



디스크�매거진을�빼서�그�디스크의�번호

를�확인해주십시오 .



디스크가�심하게�긁혀있습니다 .

다른�디스크를�사용하십시오 .

카세트�테이프�소스



테이프을�뺄�수�없습니다 .

CD 를�넣으면�바로�나옵니다 .



ACC�스위치가�꺼지고�10 분�이상이�경과했

습니다 .

CD 가�상당히�더러워져�있습니다 .



<CD 에�관해서 > 를�참조해서�CD 를�청소

하십시오 .�(80�페이지 )



테이프은�ACC�스위치가�꺼지고�10 분�이

내에만�꺼낼�수�있습니다 .�10 분�이상이�

경과하면 ,�ACC�스위치를�다시�켜서�이

젝트�(Eject)�버튼을�누르십시오 .

디스크를�뺄�수�없습니다 .



ACC�스위치가�꺼지고�10 분�이상이�경과했

습니다 .

DPSS,�테이프�어드밴스 ,�음악�반복이�제대로�

작동되어지지�않습니다 .



테이프은�ACC�스위치가�꺼지고�10 분�이

내에만�꺼낼�수�있습니다 .�10 분�이상이�

경과하면 ,�ACC�스위치를�다시�켜서�이

젝트 (Eject)�버튼을�누르십시오 .



테이프에�들어�있는�노래�사이들의�스페이스

가�너무�짧아서�스페이스가�인식되어지지�않

습니다 .



노래의�사이에는�최소�4 초간의�간격을�두

디스크가�들어가지�않습니다 .

십시오 .



이미�다른�디스크가�들어�있습니다 .



노래�사이의�스페이스에�노이즈가�많이�들어�

있기�때문에�스페이스로�인식되어지지�않습

니다 .



[

]�버튼을�눌러서�디스크를�꺼내십시

오 .

다이렉트�트랙�검색과�다이렉트�디스크�검색이�

작동되어지지�않습니다 .�



노래�사이의�노이즈를�제거하십시오 .

블랭크�건너뛰기가�작동하지�않습니다 .



다른�기능이�작동�중입니다 .

랜덤�재생 ,�혹은�다른�기능을�끄십시오 .



노이즈가�너무�크기�때문에�레코드�되어지지�

않은�부분이�인식되어지지�않습니다 .



트랙�검색이�작동되어지지�않습니다 .�

처음과�마지막�노래 .

노래�사이의�노이즈를�제거하십시오 .



레코드�되어져�있는�부분에서�블랭크�건너뛰기�

기능이�작동합니다 .



모든�디스크는�처음�노래에�있어서�뒷부

분으로의�트랙�검색 ,�마지막�노래에�있어

서의�앞부분으로의�트랙�검색이�되지�않

습니다 .



레코딩�소리가�너무�작아서�그�부분이�레코딩�

되어지지�않은�것으로�인식되어졌습니다 .



블랭크�건너뛰기를�끄십시오 .

< 음악의�반복 >(91 페이지 ) 가�임의로�취소되었

습니다 .



전원이�OFF 로�되었거나 ,�소스�선택�또는�

다른�조작이�실행중입니다 .



전원이�OFF 또는�소스�선택�또는�기타�

조작이�실행중에�음악�반복이�취소되었습

니다 .

한글

105

Download from Www.Somanuals.com. All Manuals Search And Download.



트러블�처치�가이드

MP3/WMA�소스

아래의�메시지는�여러분의�시스템�컨디

션을�나타냅니다 .

MP3/WMA�파일이�재생되지�않는다 .



매체가�긁혔거나�더럽다 .

80 페이지의〈CD 에�관해서 �를�참조해

서�매체를�청소한다 .

EJECT:

체인저에�디스크�매거진이�삽입되어�

있지�않습니다．디스크�매거진이��완

전히�삽입되어�있지�않습니다 �

 디스크�매거진을�바르게�삽입해�주

십시오．

MP3/WMA�파일의�재생�도중�음이�튄다 .



매체가�긁혔거나�더럽다 .

80 페이지의〈CD 에�관해서 �를�참조해

서�매체를�청소한다 .

레코딩�컨디션이�좋지않습니다 .

기기에�CD 가�없습니다 .

 CD 를�넣으십시오 .



No�Disc:

디스크�매거진에�디스크가�들어있지�

않습니다 .�



메디아를�다시�기록하거나�다른�메디아를�

사용하십시오 .

 디스크�매거진에�디스크를�넣으십

시오 .

MP3/WMA�화일�시간이�바르게�표시되어지지�

않습니다 .�

Error�04: CD 가�상당히�더러워져�있습니다．

CD 가�반대로�되어�있습니다．

 CD 의�손질을�하고�바르게�삽입해�

주십시오．



---



MP3�레코딩�컨디션에�따라�MP3�시간이�

정확히�표시되어지지�않을�경우가�있습니

다 .

Error�05: CD 의�앞뒷면이�반대로�되어져�있습

니다 .

 CD 를�바르게�넣으십시오 .

만약�다음과�같은�상황이�발생하면�가까

Blank:

MD 에�아무것도�녹음되어�있지�않습

니다．

운�서비스센터에�상담해�주십시오 :

디스크� 체인저가� 접속되어� 있는데도� 디스크� 체인저�

모드가� � 작동하지� � 않고� 체인저� 모드중에� 디스플레

이에�"AUX�EXT" 가�표시될�때．

No�Track: 타이틀은�있지만�MD 의�트랙에�녹음

되어�있지�않습니다 �

Error�77: 무엇인가의�이유로�기기가�작동하지�

않습니다 �

 기기의�리세트�버튼을�누릅니다．

그래도�"Error�77" 코드가��꺼지지��

않을�경우는�가까운�서비스센터로�

연락해�주십시오．

Error�99:

디스크�체인저에�불량이�있습니다．무

엇인가의�이유로�기기가�작동하지��않

습니다．

 디스크�매거진을�조사합니다．그

리고�기기의�리세트�버튼을�누릅니

다．그래도�"Error�99" 코드가�꺼

지지�않을�경우는�가까운�서비스센

터로�연락해�주십시오．

106

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

Hold:

자동�디스크�체인저내의�온도가�60℃

(140F) 를�넘을�경우�장치내의�보호

회로가�작동하여�모든�조직이�정지합

니다 �

 창문을�열거나�에어컨을�켜서�기기

를��냉각시킵니다．온도가��60℃

(140F) 미만으로�되면�디스크는�다

시�재생을�시작합니다．

No�Name: 사전�설정되어진�이름이�없는�CD 가�

재생되어지는�중에�DNPS 를�표시하

려고�했습니다 .�

Load:

디스크�체인저에�디스크가�교환되어지

고�있습니다 .

Reading:

기기가�디스크의�데이터를�읽고�있습

니다 .�

�( 깜박거립니다 ):

CD�플레이어�섹션이�바르게�작동되어

지고�있지않습니다 .

 CD 를�다시�넣으십시오 .�만일 ,�

CD 를�잘�넣었는데도�불구하고�계

속�깜박거리거나�CD 가�나오지�않

는다면 ,�스위치를�끄고 ,�가까운�서

비스�센터에�문의하십시오 .

�( 깜박거립니다 ):

테이프�플레이어��섹션이�바르게�작동

되어지고�있지않습니다 .�

 테이프을�다시�넣으십시오 .�만일 ,�

테이프을�잘�넣었는데도�불구하고�

계속�깜박거리거나�테이프이�나오

지�않는다면 ,�스위치를�끄고 ,�가까

운�서비스�센터에�문의하십시오 .

N/A�File: 본�기기가�지원하지�않는�포멧으로�

MP3/WMA 가�재생되어집니다 .



----

Protect:

복사방지�파일�실행�중 .



----

한글

107

Download from Www.Somanuals.com. All Manuals Search And Download.

:�

100�dB�(1�kHz)

:�

MPEG-1/2�오디오�레이어 -3�준수

:�

윈도우�미디어�오디오�과�호환

:�

50�W×4

:�22�W×4

:�

1800�mV�/�10�kΩ

:�

20�Hz�—�20�kHz

:�1200�mV

:�

100�kΩ

:�

14.4�V�(11�—�16�V�허용 )

:�

500�—�200�rpm�(CLV)

:�

측정한계�이하

사양

사양은�사전�예고없이�변경되는�경우도�있습니다．

주파수�응답�(±1�dB)

:�10�Hz�—�20�kHz

토털�하모니�찌그러짐�(1�kHz)

:�0.01�％

FM�튜너

주파수�범위

50�kHz�스페이스 :

87.5�MHz�—�108.0�MHz

신호대�잡음비

200�kHz�스페이스 :�

87.9�MHz�—�107.9�MHz

다이내믹�범위

:�93�dB

채널�분리

:�85�dB

사용�가능�감도�(S/N�=�30�dB)

:�9.3�dBf�(0.8�μV�/�75�Ω)

소음�감도�(S/N�=�50�dB)

:�15.2�dBf�(1.6�μV�/�75�Ω)

주파수�응답�(±3.0�dB)

:�30�Hz�—�15�kHz

신호대�잡음비�(MONO)

:�70�dB

선택률�(±400�kHz)

:�≥�80�dB

스테레오�분리�(1�kHz)

:�30�dB

MP3�디코더

WMA�디코딩

오디오

최대�출력�

전대역폭�(1％�THD�미만에서 )

AM�튜너

주파수�범위�

9�kHz�스페이스 :�

프리아웃�레벨

프리아웃�인피던스�

:�≤�600�Ω

531�MHz�—�1611�MHz

10�kHz�스페이스 :

530�MHz�—�1700�MHz

사용�가능�감도�(S/N 〓 20�dB)

:�28�dBμV�(25�μV)

보조�입력

주파수�응답

카세트�플레이어

테이프�속도�

:�4.76�cm�/�sec.

Wow�&�플루터�(WRMS)

:�0.1�％

주파수�응답�(70�μs)

:�40�Hz�—�20�kHz�(±3�dB)

분리�(1�kHz)

:�35�dB

최대�입력�전압

입력�인피던스

일반

조작�전원�

신호대�잡음비

돌비�NR�OFF�:�50�dB

돌비�B�NR�ON�:�60�dB

소비�전류

:�10.0�A

크기�(W×H×D)

:�178×100×155�mm

무게

:�2.3�kg�

CD�플레이어

레이저�다이오드

:�GaAIAs�

디지털�필터�(D/A)

:�샘플링에서는�8 회

D/A�컨버터

:�1�Bit

회전�속도

Wow�&�플루터

108

한글

Download from Www.Somanuals.com. All Manuals Search And Download.

Inova Computer Hardware ICP PII User Manual
Intellinet Network Solutions Network Router 523615 User Manual
Invacare Mobility Aid P7ETM User Manual
Jet Tools Saw JWBS 14DX User Manual
JL Audio Car Speaker C2 650x User Manual
JVC Camcorder GR AX920 User Manual
JVC MP3 Player RV NB10B User Manual
Kidde Smoke Alarm TM0098 User Manual
Konica Minolta GPS Receiver NS NAV02R GPS User Manual
Konica Minolta Marine Radio CS 2000 User Manual