Kenwood Car Satellite TV System KMD 870R User Manual

MD-RECEIVER

KMD-870R

INSTRUCTION MANUAL

00/2 1 99/12 11 10 9 8 7 6 5 4 3 2 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

IMPORTANT INFORMATION

2WARNING

2CAUTION

You cannot connect the unit directly to the

following CD automatic changers. For users

who want to use older changers with the

unit, follow the directions below according to

the type of changer you own:

To prevent injury and/or fire, take the

following precautions:

• Insert the unit all the way until it is fully

locked in place. Otherwise it may fly out of

place during collisions and other jolts.

To prevent damage to the machine,

take the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• KDC-C200 / KDC-C300 / KDC-C400

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not set the removed faceplate or the

faceplate case in areas exposed to direct

sunlight, excessive heat or humidity. Also

avoid places with too much dust or the

possibility of water splashing.

• To prevent deterioration, do not touch the

terminals of the unit or faceplate with your

fingers.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision equipment.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

• To prevent short circuits when replacing a

fuse, first disconnect the wiring harness.

• Do not place any object between the

faceplate and the unit.

Use the extension cable and the control box

attached to the CD changer, and the optional

CA-DS100 converter cable.

• KDC-C301 / KDC-C600 / KDC-C800 / KDC-

C601 / KDC-C401

Use the extension cable attached to the CD

changer, and the optional CA-DS100

converter cable.

• KDC-C100 / KDC-C302 / C205 / C705 /

non-Kenwood CD changers

• When extending the ignition, battery or

ground cables, make sure to use automotive-

grade cables or other cables with an area of

0.75mm (AWG18) or more to prevent cable

deterioration and damage to the cable

coating.

• To prevent short circuits, never put or leave

any metallic objects (e.g., coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• Be careful not to drop the unit or subject it to

strong shock.

The unit may break or crack because it

contains glass parts.

• Do not touch the liquid crystal fluid if the LCD

is damaged or broken due to shock. The

liquid crystal fluid may be dangerous to your

health or even fatal.

If the liquid crystal fluid from the LCD

contacts your body or clothing, wash it off

with soap immediately.

Cannot be used with this model.

2CAUTION

You can damage both your unit and

the CD changer if you connect them

incorrectly.

• During installation, do not use any screws

except for the ones provided. The use of

improper screws might result in damage to

the main unit.

— 3 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

Handling Mini discs

Lens Fogging

NOTE

• The MD shutter is designed so that it cannot

be opened. If forced open, the cartridge will

be damaged and use of the MD will no

longer be possible. If the shutter has been

opened due to some cause, be careful not to

touch the recording portion with a finger.

Doing so will cause the sound to skip.

In cold climates, there may be a period after

you turn on your vehicle's heater when the

lens that guides the laser beam used in your

MD player fogs up. If this happens, you

cannot play mini discs. Take out discs and

the fogging will disappear. If it does not

return to normal after several hours, contact

your Kenwood dealer.

• If you experience problems during

installation, consult your Kenwood dealer.

• If the unit does not seem to be working right,

try pressing the reset button first. If that does

not solve the problem, consult your Kenwood

dealer.

Egnlish

POWER

OFF

SRC

CLK

DISC

The marking of products using lasers

(Except for some areas)

PTY

NAME.S

TI VOL ADJ DISP

DISC

ATT

LOUD

SCAN

RDM

REP

D.SCN

M.RDM

AUD

CLASS 1

LASER PRODUCT

• Do not use an MD that has a peeling label.

Use of an MD that has a loose or peeling

label may cause problems, such as the label

coming off inside the player and the resultant

inability to eject the MD.

• Wipe away dirt or dust from the cartridge

surface with a dry cloth before use. Using an

oil-soiled cartridge in particular may result in

the disc not loading or being unable to eject

it. (At time of cleaning, be careful not to open

the shutter.)

Reset button

• Characters in the LCD may become difficult

to read in temperatures below 41 ˚F (5 ˚C).

The label is attached to the chassis/case and

says that the component uses laser beams

that have been classified as Class 1. It means

that the unit is utilizing laser beams that are

of a weaker class. There is no danger of

hazardous radiation outside the unit.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get

dirty, wipe them with a dry, soft cloth.

Cleaning the Unit

• Do not leave the MD in the unit for a

prolonged period. The ejected MD should be

placed in an MD case for storage.

If the front panel gets dirty, turn off the

power and wipe the panel with a dry silicon

cloth or soft cloth.

• Do not leave the MD in a place exposed to

direct sunlight (such as on a instrument

panel) or in other places that reach high

temperatures. The MD cartridge will become

misshapen and will no longer be usable.

• MDs designed for use with data cannot be

used. Please use MDs designed for music.

2CAUTION

Do not wipe the panel with a stiff cloth or a

cloth dampened by volatile solvents such as

paint thinner and alcohol. They can scratch

the surface of the panel and/or cause the

indicator letters to peel off.

US and foreign patents Iicensed from Dolby

Laboratories Licensing Corporation.

• Do not use lens cleaners. Doing so will lead

to breakdown.

— 4 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations

SRC /

PWR OFF

Power

Turning on the power:

POWER

OFF

SRC

Press the SRC button.

CLK

DISC

NOTE

PTY

Turn the power on before carrying out the following procedures.

NAME.S

TI VOL ADJ

DISP

DISC

ATT

LOUD

SCAN

RDM

REP

D.SCN

M.RDM

Turning off the power:

AUD

Hold down the PWR OFF button for one second or more.

ATT / LOUD

Switching Modes

Switching Modes:

Each time you press the SRC button, the mode switches as

follows:

▼

Tuner mode

▼

MD mode

▼

LOUD indicator

External disc control mode

▼

LOUD

ATT

AUX mode

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc control mode will differ depending on the unit

that is connected.

ATT indicator

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS82 or KDC-CX82) is connected to this unit.

During the AUX mode, "AUX" will show in the display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

— 5 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations

Volume

Menu System

To accommodate a greater number of functions, a menu

system has been employed for making settings. Press the

MENU button to enter the menu mode and then display the

function to make the setting. Details on each setting are

explained separately in the corresponding function page.

Increasing Volume:

Press the u button to turn up the volume.

Egnlish

Decreasing Volume:

Press the d button to turn down the volume.

Hold down the MENU button for one second or more.

"MENU" is displayed when the menu mode is entered.

The function that you can adjust is indicated with the current

settings displayed.

Attenuator

This function allows you to turn down the volume quickly.

Selecting function to set

Press the ¢ button to search through the functions until you

see the one you want to adjust in the display.

Press the 4 button to search through the functions

backward.

Example: If you want to switch the tuning mode from Auto1 to

manual, first search through the functions until you

see "Auto 1" in the display.

Turning Attenuator On/Off:

Press the ATT button to switch the attenuator on and off.

When the attenuator is on, the ATT indicator blinks.

When the attenuator is off, the volume returns to the original

level.

NOTE

Turning down the volume all the way turns off the attenuator

function.

Changing setting for currently displayed function

Press either the AM or FM button.

The setting will change for each function.

Example: The tuning mode will switch from Auto 1 to Auto 2.

Pressing the button again switches the setting to

manual, and "Manual" is displayed.

Loudness

This function amplifies low and high tones when the volume is

turned down.

The LOUD indicator lights up, when the loudness function is

on.

Auto 2

Manual

Turning Loudness On/Off:

Hold down the LOUD button for one second or more to switch

the loudness on and off.

Ending the menu mode

Press the MENU button.

The selection includes:

Touch Sensor Tone (Beep ON / OFF) ↔ Time Adjustment*

<Manual> (CLK ADJ* ) ↔ Automatic Time Adjustment*

(SYNC ON / OFF) ↔ Disabled System Indicator (DSI ON /

OFF) ↔ Selectable Illumination (COL GRN / AMB) ↔ Contrast

Adjustment (CONT ##) ↔ Dimmer (DIM ON / OFF) ↔

— 6 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

Switching Graphic Display(GRAP ON / OFF) ↔ News Bulletin

SRC

Function (NEWS OFF / ##M) ↔ Local seek* (LO.S OFF / ON)

↔ Selecting Tuning Mode* (Auto 1 / Auto 2 / Manual) ↔

POWER

OFF

SRC

Auto Memory Entry* (A-Memory (start)) ↔ AF Function* (AF

CLK

ON / OFF) ↔ Region Restrict Function* (REG ON / OFF) ↔

DISC

Auto TP Seek* (ATPS ON / OFF) ↔ Monaural Reception*

PTY

(MONO OFF / ON) ↔ Text Scroll* (SCL Manu / Auto) ↔

NAME.S

TI VOL ADJ

DISP

DISC

ATT

LOUD

SCAN

RDM

REP

D.SCN

M.RDM

Touch Sensor Tone

* When Automatic Time Adjustment is off

AUD

* Time adjustment mode entered

* In FM, MD, or External disc control mode

In Tuner mode

#1~6

DISP

In FM reception of Tuner mode

NOTE

• Make sure to end the menu mode when finished.

If you fail to end the menu mode, several functions may not

operate properly, including the Traffic Information function, the

News Bulletin function with PTY news timeout setting, and the

Alarm function.

• The News function turns on when the setting is made for the

news interruption interval. The "##M" display indicates the

setting selected for the news interruption timeout interval.

• The "##" display indicates the setting value.

STEREO indicator

Mode display

Frequency

STEREO

AUTO

III

Band display

AUTO indicator

Preset station number

— 7 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

NOTE

Selecting Tuning Mode

If the frequencies stored at the preset numbers receive

stations which were not originally memorized when traveling

long distances, the preset number is not displayed. In such

cases, pressing the 4/¢ button to use preset station seek

will receive channel 1.

You can choose from three tuning modes: auto seek, preset

station seek, and manual. The “AUTO 1” indicator lights up

when auto seek tuning is selected, and the “AUTO 2” indicator

lights when preset station seek tuning is selected.

Egnlish

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

• Manual Tuning

Press the ¢ button to increase the frequency by one step.

Press the 4 button to decrease the frequency by one step.

Press the ¢ button repeatedly until the tuning function

appears in the display.

NOTE

Press the 4 button to search in the other direction.

The tuning method is displayed as ”Auto 1“, ”Auto 2“, or

”Manual“ referring respectively to auto seek tuning, preset

station seek tuning, and manual tuning.

The STEREO indicator lights up when stereo broadcasts are being

received.

Switching settings

Press either the AM button or FM button to switch the tuning

mode.

Local Seek Function

With the local seek function turned on, auto seek tuning skips

stations with relatively poor reception.

The display and setting will change.

Press the MENU button to end the menu mode.

Turning Local Seek Function On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Tuning

Press the SRC button repeatedly until the tuner mode is

Press the ¢ button repeatedly until the local seek function

appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "LO.S ON" or "LO.S OFF" in

the display, indicating that the local seek function is on or off,

respectively.

obtained. "TUNER" is displayed only when the tuner mode is

selected.

Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2 and FM3.

Press the AM button to select the MW and LW bands.

Switching settings

Press either the AM button or FM button.

The display and setting will change.

• Auto Seek Tuning

Press the ¢ button to seek increasing frequencies.

Press the 4 button to seek decreasing frequencies.

• Preset station seek tuning

Press the MENU button to end the menu mode.

Press the ¢ button to move to the next preset station (i.e.,

the one with the next highest number), and the 4 button to

move to the last preset station (i.e., the one with the next

lowest number).

— 8 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Recalling a Preset Station:

Station Preset Memory

Store the frequency of the station currently being listened to.

You can then recall that station with a single touch of a button.

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

NOTE

Select the band/ station that you want to have stored.

• When the AF function is turned on whilst auto memory entry

takes place, only RDS stations (i.e., stations with RDS capability)

are stored. RDS stations that have been preset for FM1 cannot

also be preset in FM2 or FM3.

• When the local seek function is turned whilst auto memory

entry takes place, stations with poor reception are not stored.

• When the Traffic Information function is on , only the local traffic

information station frequency will be stored.

Hold down the button (#1-6) that you want to use for the

station, for two seconds or more.

The button number blinks once in the display to indicate that

the data has been stored.

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Cancelling Auto Memory Entry During Its Operation:

Press the MENU button whilst auto memory entry is taking

place to stop the process.

NOTE

You can store 6 stations in each of the FM1, FM2, FM3, and AM

(MW and LW) bands.

Auto Memory Entry

You can automatically store all the receivable frequencies in

the band currently being listened to, and then recall them with

the touch of a button later. This function is especially useful

when you are travelling and do not know what stations are

available. Up to 6 frequencies can be stored this way.

Select the band for auto memory entry.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until "A-Memory" appears in

the display.

Press the 4 button to search in the other direction.

Hold down either the AM button or FM button for two seconds

or more to start auto memory function.

The numbers of the preset station buttons showed in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

— 9 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

Monaural Reception

When poor stereo reception is experienced, this function will

reduce noise and improve listening conditions.

Preset station seek with Programme service

name

(Function of Remote)

You can search for the preset station with Programme Service

name.

Egnlish

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the DNPP button on the remote control.

“SNPP” will be displayed once the seek mode is entered.

The names of the stations preset in the band currently listened

to are displayed for 5 seconds each.

Press the ¢ button repeatedly until the monaural reception

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "MONO OFF" or "MONO

ON" in the display, indicating that monaural reception is on or

off, respectively.

The display band switches in the following order:

= FM1 Ô FM2 Ô FM3 Ô AM +

Each time you press the ¢ button, the station display

switches in the forward direction.

Switching settings

Press either the AM button or FM button.

The display and setting will change.

Each time you press the 4 button, the station display

switches in the reverse direction.

Stations which have no names will be displayed as frequencies.

Press the MENU button to end the menu mode.

NOTE

Changing the Displayed Band

Pressing the FM button switches between the FM1, FM2, FM3

and AM displays, in that order.

Pressing the AM button switches between the displays in the

reverse direction.

Once the name is displayed for the station you want to listen

Press the OK button.

Reception starts of the displayed station, and the seek mode

ends.

Cancelling mode during input:

Press the DNPP button.

The seek mode is cancelled.

— 10 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS features

38/PTY

RDS (Radio Data System)

RDS is a digital information system that lets you receive signals

besides those of regular radio programmes, such as network

information being transmitted from radio stations.

When listening to an RDS station (ie, a station with RDS

capability), the programme service name of the station is

displayed along with the frequency, advising you quickly which

station is being received.

POWER

OFF

SRC

CLK

DISC

PTY

NAME.S

TI VOL ADJ DISP

DISC

ATT

LOUD

SCAN

RDM

REP

D.SCN

M.RDM

AUD

RDS (Radio Data System) stations also transmit frequency data

for the same station. When you are making long trips, this

function automatically switches to the particular frequency with

the best reception for the particular network of stations that

you want to listen to. The data is automatically stored,

allowing you to switch quickly to another RDS stations,

broadcasting the same programme, that has better reception.

These include stations stored in the station preset memory that

you often listen to.

TI /

VOL ADJ

#1~6

DISP

EON (Enhanced Other Network)

NEWS indicator

Stations that offer EON also transmit information about other

RDS stations that have traffic information. When you are tuned

to a station that is not transmitting traffic information, but

another RDS station starts transmitting a traffic bulletin, the

tuner automatically switches to the other station for the

duration of the bulletin.

NEWS

TEXT

III

Band display

TI indicator

™ indicator

Alarm

When an emergency transmission (announcing disasters, etc.)

is sent, all current functions are interrupted to allow the

warning to be received.

— 11 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS features

Turning Region Restrict Function On/Off:

AF (Alternative Frequency) Function

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

When poor reception is experienced, automatically switch to

another frequency broadcasting the same programme in the

same RDS network with better reception.

The ™ indicator lights up when the AF function is turned

on.

Press the ¢ button repeatedly until the Region restrict

function appears in the display.

Egnlish

Press the 4 button to search in the other direction.

The function setting is indicated by "REG ON" or "REG OFF" in

the display, indicating that the function is on or off,

respectively.

Turning AF Function On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Switching settings

Press the ¢ button repeatedly until the AF function appears

in the display.

Press either the AM button or FM button.

The display and setting will change.

Press the 4 button to search in the other direction.

The function setting is indicated by "AF ON" or "AF OFF" in the

display, indicating that the AF function is on or off, respectively.

Press the MENU button to end the menu mode.

NOTE

Sometimes stations in the same network broadcast different

programmes or use different programme service names.

Switching settings

Press either the AM button or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

Displaying Frequencies:

Hold down the DISP button for one second or more.

The frequency for the RDS station will be displayed for five

seconds instead of the station name.

Traffic Information Function

You can listen to traffic information. If you are listening to

tapes or discs, they will continue playing until a traffic bulletin

is broadcast.

NOTE

When no other stations with stronger reception are available for

the same programme in the RDS network, you may hear the

incoming broadcast in bits and snatches. Turn off the AF function

in such a case.

Turning TI function On/Off:

Press the TI button to turn the function on and off.

When the function is on, the TI indicator is turned on.

When none is being received, the TI indicator will blink on and

off. When a traffic information station is being received, the TI

indicator will turn on.

When a traffic bulletin begins to be broadcast, "TRAFFIC" will

be displayed, and reception will begin at the preset volume.

If you are listening to a tape or disc when a traffic bulletin

begins, they will automatically be turned off. When the bulletin

ends or poor reception is experienced, the tape or disc will

begin playing again.

Restricting RDS Region (Region Restrict Function)

You can choose whether or not to restrict the RDS channels,

received with the AF function for a particular network, to a

specific region. When the Region Restrict Function is on, the

region is restricted.

— 12 —

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE

Switching settings

Pressing the TI button whilst in the MW/LW band automatically

switches reception to the FM band. However, the MW/LW band

is not returned to when the TI button is pressed again.

Press either the AM button or FM button.

The display and setting will change.

If the traffic information station you are tuned to experiences

poor reception, this function automatically seeks another TP

station.

Switching to a Different Traffic Information Station:

Use the 4 / ¢ buttons to make an auto seek of the TI

stations in a certain band.

Press the MENU button to end the menu mode.

NOTE

• When you are listening to a tape or disc, you cannot change to

another TI station.

• When the auto TP seek function is turned on and reception

starts to weaken, the tuner automatically seeks traffic

information stations with better reception.

Presetting Volume for Traffic Information/News

Preset the volume level to be used for traffic information and

news broadcasts.

• If you are tuned to a station that is not a traffic information

station itself but which provides EON services, you can still have

traffic information received.

• Holding the TI button down for one second or more when the TI

function is on in the disc control mode results in a change to the

frequency display of the traffic information station for five

seconds.

Tune into the station for which you want to set the volume.

Adjust the volume to the desired level.

Hold down the TI VOL ADJ button for two seconds or more.

The volume level blinks once in the display to indicate that the

data has been stored.

Future traffic information/news broadcasts are heard at the

preset level.

NOTE

Auto TP Seek Function

• The volume cannot be lowered by this function during tuner

reception. The volume is only set when it is louder than the

listening volume of the tuner.

• You can arrange only to listen to traffic information or news

bulletins with at preset volume with the volume set at

minimum.

When the TI function is on and poor reception conditions are

experienced when listening to a traffic information station,

another traffic information station with better reception will be

searched for automatically. This function is on, when unit is

first powered on.

Turning Auto TP Seek Function On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Auto TP Seek

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "ATPS ON" or "ATPS OFF" in

the display, indicating that the function is on or off,

respectively.

— 13 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS features

NOTE

News Bulletin Function

with PTY News Timeout Setting

• This function is only available if the desired station sends PTY-

code for news bulletin or belongs to EON-Network sending PTY-

code for news bulletin.

• If you turn on the news bulletin function in the MW/LW band,

the band is switched automatically to the FM band.

However, the MW/LW band is not returned to when you turn off

the function.

You can arrange to have news bulletins interrupt your current

listening source, including other radio stations. When the News

Bulletin function is on, the PTY News Timeout setting allows

you to set the interval during which further news interruption

cannot take place. You can adjust the PTY news interruption

period from 10 to 90 minutes for each journey.

Egnlish

Turning News Bulletin Function On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Programme Type (PTY) Function

Conduct auto seek tuning only on those stations with selected

kinds of programmes.

Press the ¢ button repeatedly until the News Bulletin

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "NEWS OFF" or "NEWS

##M" in the display, indicating that the function is on or off,

respectively.

Press the 38(PTY) button.

“PTY” is displayed, and the Programme Type Selection (PTY)

Mode entered.

NOTE

If you make no key input in 30 seconds, the mode will

automatically turn off.

Depending on the interval chosen, the "##M" in the display will

change when the function is turned on.

NOTE

You cannot use this function whilst the traffic information

function is turned on.

Changing the Function Setting

Press either the FM or AM button.

Each time you press the FM or AM button until the desired

setting is displayed.

NOTE

Changing the Display Language to French, German, or Swedish

In the PTY mode, hold down the 38(PTY) button for one second

or more to display the name of the language currently used.

If you want to change the language, press the preset button for

the desired language and then the 38(PTY) button.

Press the FM button to increase the interval, and the AM

button to decrease it.

OFF ↔ 00M ↔ 10M ↔ 20M ↔ 30M ↔ 40M ↔ 50M ↔ 60M

↔ 70M ↔ 80M ↔ 90M

(M= minutes)

English is #1, French is #2, German is #3, and Swedish is #4.

When you select the news interruption timeout interval, the

News function turns on and the NEWS indicator lights up.

When a news bulletin is received, "NEWS" will be displayed and

reception will begin at the preset volume.

Select the type of programme to be received

• Press either the FM or AM buttons repeatedly until the type

of programme you want to listen to.

The selection includes:

NOTE

Speech(Speech) ↔ 1.News (News) ↔ 2.Current Affairs

(Affairs) ↔ 3.Information (Info) ↔ 4.Sports (Sport) ↔

5.Education (Educate) ↔ 6.Drama (Drama) ↔ 7.Culture

(Culture) ↔ 8.Science (Science) ↔ 9.Varied (Varied) ↔

10.Pop Music (Pop M) ↔ 11.Rock Music (Rock M) ↔

If you choose the "20M" setting, further news bulletins will not be

received for 20 minutes once the first news bulletin is received.

Press the MENU button to end the menu mode.

— 14 —

Download from Www.Somanuals.com. All Manuals Search And Download.

12.Easy listening Music (Easy M) ↔ 13.Light Classical (Light

M) ↔ 14.Serious Classical (Classics) ↔ 15.Other Music

(Other M) ↔ 16.Weather (Weather) ↔ 17.Finance (Finance)

↔ 18.Children’s programmes (Children) ↔ 19.Social Affairs

(Social) ↔ 20.Religion (Religion) ↔ 21.Phone In (Phone In)

↔ 22.Travel (Travel) ↔ 23.Leisure (Leisure) ↔ 24.Jazz

Music (Jazz) ↔ 25.Country Music (Country) ↔ 26.National

Music (Nation M) ↔ 27.Oldies Music (Oldies) ↔ 28.Folk

Music (Folk M) ↔ 29.Documentary (Document) ↔ Music

(Music) ↔ Speech (Speech) ↔

Cancelling Programme Type Function During Its Operation:

Press the 38(PTY) button.

(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)

• You can select the type of programme directly by pressing a

preset button. The buttons are factory-set to the following

type of programmes:

1. Music

4. Other Music

2. Speech

5. Serious Classical

3. News

6. Varied

NOTE

Changing the Preset Button Settings for Programme Type

After selecting the type of programme to be stored in a certain

preset button, hold down that button for two seconds or more.

The previously stored data for that button are erased and the new

programme type is stored.

Seeking the selected programme type

Press the 4 or ¢ button to make a seek of frequencies

with your selected type of programme.

The display blinks and the seek starts.

If your selected type of programme is found, the name of the

station is displayed and the station is tuned into.

“PTY” blinks in the display for about 30 seconds.

If you make no key input in 30 seconds, the PTY selection

mode will turn off automatically.

NOTE

If no programme can be found, "NO PTY" is displayed.

If you want to select another type of programme, repeat steps 2

and 3 above.

Switching to Other Stations with the Same Type of Programme:

When “PTY” is blinking in the display, perform auto seek

tuning.

The tuner scans for another station with the same type of

programme.

— 15 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS features

Text Scroll

Radio Text

This function permits the text to be scrolled and the entire text

to be displayed. Switching between manual scrolling and

automatic scrolling is permitted. The factory default is manual

scrolling.

You can display textual information being transmitted by RDS

stations.

Egnlish

Turning on Radio Text Display Mode:

Pressing the DISP button switches the display as follows.

Select the Radio Text Display mode.

To scroll manually:

Press the DISP button to display the Radio Text.

Programme Service name

Radio text

Holding down the DISP button for one second or more results

in one scrolling display of the text.

Manual/Automatic scroll switching:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

NOTE

If the RDS station currently tuned to is transmitting no text whilst

the Radio Text Display mode is turned on, "NO TEXT" will appear

in the display. Whilst awaiting reception, "WAITING" will be

displayed.

Press the ¢ button repeatedly until the Text scroll function

appears in the display.

Pressing the 4 button results in the functions being switched

in the reverse order.

2WARNING

The text scroll function is displayed with "SCL Auto" or "SCL

Manu".

To prevent accidents, drivers should not look at the display whilst

on the road.

"SCL Manu" (Manual scrolling)

"SCL Auto" (Automatic scrolling)

Switching settings

Press either the AM or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

To scroll automatically:

Press the DISP button to display the Radio Text.

The text will be displayed in one scrolling display.

Holding down the DISP button for one second or more results

in one scrolling display of the text.

NOTE

The setting of the text scroll function is in common with Text

Scroll for disc control.

— 16 —

Download from Www.Somanuals.com. All Manuals Search And Download.

MD/External disc control features

Release button

■When a unit equipped with an O-N switch is to be connected,

please also see the instruction manual of this unit.

Set the O-N switch to "N". "N"-operation will be set.

■When a unit that is not equipped with an O-N switch, or the

changer switching unit "KCA-S200" is connected, "O"-

operation will be set.

FM/

DISC+

SRC

POWER

OFF

SRC

CLK

DISC

"N"-operation:

PTY

NAME.S

TI VOL ADJ DISP

• The disc title and track title of the CD text can be displayed.

• The disc name will be displayed when the name has been

registered to any connected unit with the Presetting Disc

Names function, or when the playing unit contains a disc to

which the disc title has been recorded.

ATT

LOUD

SCAN

RDM

REP

D.SCN

M.RDM

AUD

REP

M.RDM

SCAN

DISP/

NAME.S

AM/

DISC-

RDM

D.SCN

"O"-operation:

• CD text cannot be displayed.

• Regardless of the control unit, the characters that can be

registered with the Presetting Disc Names function are "A~Z

0~9 /, +, –, ∗, =, <, >, [ , ]".

• The disc name will be displayed when the name has been

registered to the playing unit with the Presetting Disc Names

function.

NOTE

Track time

The CD text, Presetting Disc Names, and Disc Name Preset Play

functions may not be operational depending on the unit.

III

Mode display

Disc number

(For disc changers)

Track number ¢ indicator

— 17 —

Download from Www.Somanuals.com. All Manuals Search And Download.

MD/External disc control features

• Do not apply excessive force to the open faceplate or place

objects on it. Doing so will cause damage or breakdown.

• Do not use the unit with the faceplate in the open condition.

Doing so will cause breakdown.

Playing MDs

Playing MDs:

A press of the release button causes the faceplate to drop to

the front, thereby exposing the MD slot.

Egnlish

Insert the MD in the proper orientation. The MD will start

playing. Push back on the right side of the faceplate with your

hand until it locks.

Playing Other Disc mode

The ¢ indicator will light when an MD has been inserted.

This function permits the connection of optional players and

the playing of discs other than the loaded MD (in the current

unit).

2CAUTION

When inserting an MD, make sure the MD has been completely

drawn in before pushing back the faceplate. Failing to do so might

deform the MD.

Playing Discs:

Press the SRC button repeatedly to select the external disc

control mode.

Playing MDs Already Inserted:

Press the SRC button repeatedly until the MD mode is

obtained.

The disc will start playing.

NOTE

"MD" is displayed when the MD mode has been selected.

The MD will start playing.

The external disc control mode will differ, depending on the unit

that is connected.

Mode Display Examples

• "CD"...when a CD player is connected

• "DISC"...when a disc changer is connected

• "DISC-1", "DISC-2"...when two disc changers are connected

Pausing and Restarting MD Play:

Press the 38 button to make the disc pause.

Press the same button again to start play again.

Eject:

Press the release button and drop open the faceplate.

Press the 0 button located near the MD slot.

The MD stops playing and ejects from the slot.

Push back on the right side of the faceplate with your hand until

it locks.

Pausing and Restarting Disc Play:

Press the 38 button to make the disc pause.

Press the same button again to start play again.

NOTE

• When one disc has finished playing its last track, the next disc in

the changer will start playing. When the last disc in the changer

has finished, the player will return to the first disc and start

playing it.

• Disc #10 is displayed as "0".

2CAUTION

• When the faceplate has been dropped open, it might interfere

with the shift lever or something else. If this happens, pay

attention to safety and move the shift lever or take an

appropriate action, then operate the unit.

Fast Forwarding and Reversing Disc Play

Fast Forwarding Disc Play:

— 18 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Hold down on the ¢ button.

Disc Search

Search forwards or backwards through the discs in a disc

changer until you reach the one that you want to listen to.

(Function of disc changers)

Release your finger to play the disc at that point.

Reversing Disc Play:

Hold down on the 4 button.

Release your finger to play the disc at the point.

Making a Reverse Disc Search:

Press the DISC– button to display the desired disc number.

Each time the button is pressed, the displayed disc number

decreases by one.

NOTE

You cannot use reverse play between tracks depending on the

model being connected. Instead, the reverse play function is

cancelled when it reaches the beginning of a track, at which point

normal play automatically resumes.

Play starts at the beginning of the displayed disc.

Making a Forward Disc Search:

Press the DISC+ button to display the desired disc number.

Each time the button is pressed, the displayed disc number

increases by one.

Play starts at the beginning of the displayed disc.

Track Search

NOTE

Search forwards or backwards through the tracks on the disc

until you reach the one that you want to listen to.

"LOAD" is displayed when discs are being exchanged on the disc

changer.

Making a Reverse Track Search:

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current track,

twice to search back to the beginning of the previous track, and

so forth.

Play starts at the beginning of the displayed track number.

NOTE

(For disc changers)

Pressing the 4 button whilst listening to track 1 only searches

back to the beginning of that track. The reverse search is not

"recycled" to the last track on the disc.

Making a Forward Track Search:

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

Play starts at the beginning of the displayed track number.

NOTE

(For disc changers)

You cannot make a forward track search when listening to the last

track on a disc.

— 19 —

Download from Www.Somanuals.com. All Manuals Search And Download.

MD/External disc control features

Track / Disc Repeat

Repeat playing the current track or disc.

Disc Scan

(Function of disc changers)

Successively play the beginning of each disc on a changer until

you find the one that you want to listen to.

Turning Repeat Play Function On/Off:

Press the REP button to switch the repeat play function on and

off as follows :

Egnlish

Starting the disc scan:

Press the D.SCN button. "DSCN ON" is displayed and the first

10 seconds of each disc are played, in the order in which they

are loaded on the changer.

▼

Track Repeat ON

The disc number currently being heard blinks in the display.

▼

Stopping to Listen to the Disc Being Scanned:

Press the 38 or D.SCN button again to stop the scan and keep

on listening to the disc normally.

Disc Repeat ON (Function of disc changers)

▼

Track/Disc Repeat OFF

NOTE

"TREP ON/REP ON" is displayed and the track number blinks in

the display when track repeat is on.

• The disc scan function is cancelled when you stop playing a

disc.

"DREP ON" is displayed and the disc number blinks in the

display when disc repeat is on.

• The disc scan function only scans each disc on the changer

once.

NOTE

• "LOAD" is displayed when discs are being exchanged on the disc

changer.

The repeat play function is cancelled when you stop playing the

disc.

Track Scan

Random Play

Play all the tracks on the current disc in random order.

Successively play the beginning of each track on a disc until

you find the track that you want to listen to.

Press the RDM button to switch the random play function on

and off.

Starting the Track Scan :

Press the SCAN button. "TSCN ON/SCN ON" is displayed and

the first 10 seconds of each track are played, and the tracks are

played in order.

"RDM ON" is displayed when random play is turned on.

The display of the track number changes continuously as the

next track is being selected.

The track number currently being heard blinks in the display.

When the track has been selected, play starts.

The selected track number blinks in the display as it is being

played.

Stopping to Listen to the Track Being Scanned:

Press the 38 or SCAN button again to stop the scan and keep

on listening to a track normally.

NOTE

(For disc changers)

NOTE

When all the tracks on a certain disc have been played using the

random play function, the next disc on the changer starts playing

(with the random play function still turned on).

• The track scan function is cancelled when you stop playing a

disc.

• The track scan function only scans each track on a disc once.

— 20 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Text / Title Scroll

To change the track being heard, press the ¢ button.

Another track is selected and played.

This function permits the text to be scrolled and the entire text

to be displayed. Switching between manual scrolling and

automatic scrolling is permitted. The factory default is manual

scrolling.

NOTE

The random play function is cancelled when you stop playing a

disc.

To scroll manually:

Press the DISP button to display the disc title or the track title.

Holding down the DISP button for one second or more results

in one scrolling display of the titles.

Manual/Automatic scroll switching:

Hold down the MENU button for one second or more.

Magazine Random Play

Play the tracks on all the discs in the disc changer in random

order.

(Function of disc changers)

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Text/title scroll

function appears in the display.

Pressing the 4 button results in the functions being switched

Press the M.RDM button to switch the magazine random play

in the reverse order.

function on and off.

The text/title scroll function is displayed with "SCL Auto" or

"SCL Manu".

"MRDM ON" is displayed when magazine random play is turned

on.

The display of the disc and track numbers change continuously

as the next track is being selected.

"SCL Manu" (Manual scrolling)

"SCL Auto" (Automatic scrolling)

When the disc/track has been selected, play starts.

The selected disc/track number blinks in the display as it is

being played.

Switching settings

Press either the AM or FM button.

The display and setting will change.

NOTE

Press the MENU button to end the menu mode.

This function is not available with the following models:

KDC-C200/C300/C400/C301/C401

To scroll automatically:

Press the DISP button to display the disc title or the track title.

The titles will be displayed in one scrolling display.

To change the track being heard, press the ¢ button.

Another disc/track is selected and played.

NOTE

When the disc or track to be played changes, the title is displayed

in one scrolling display.

• The magazine random play function is cancelled when you stop

playing a disc.

• The time needed for random selection depends on the number

of discs loaded in the disc magazine.

Holding down the DISP button for one second or more results

in one scrolling display of the titles.

NOTE

Only units with a CD text feature permit title display.

— 21 —

Download from Www.Somanuals.com. All Manuals Search And Download.

MD/External disc control features

NOTE

Presetting Disc Names

(Function of disc changers)

The operation and characters that can be entered may change

as listed below, depending on the unit that is connected.

A press of the 38 button exits the disc name preset mode.

Operations can be followed again from Step 2 at a time such

as this, and the characters to be input are selected using the

procedure described below.

Press the DISC+ or DISC– button to display the desired

character. Besides the alphabet (capital letters only) and

numbers, you can choose the following characters: /, +, –, *,

=, <, >, [ and ].

Store the names of discs to be displayed when played.

Play the disc whose name you want to preset.

Egnlish

NOTE

• This function is not available for disc changers that do not

feature the Disc Name Preset function.

• This procedure is not to be used to store the disc and track titles

for MDs that you record.

Hold down the NAME.S button for two seconds or more.

"NAME SET" is displayed and the disc name preset mode is

Continue steps 3 and 4 until all the characters are chosen for

the name.

entered.

The cursor blinks in the position where character input can be

made.

Press either the NAME.S button on the main unit or the OK

button on the remote control.

Press either the 4 or ¢ button to move the cursor to the

desired position.

The disc name is stored and the disc name preset mode is

cancelled.

The 4 button moves the cursor to the left, and the ¢

If you make no entry in a 10-second period, the name will be

stored with the characters input so far.

button to the right.

You can also move the cursor left or right by pressing the

^TRACK+ or TRACK– buttons, respectively, on the remote

control.

NOTE

• The number of characters and discs whose names can be

stored will differ depending on the disc changer that is

connected. Please see your disc changer manual for details.

• Discs are identified by their total length and number of tracks. If

another disc happens to have the same specifications as one

that you have already stored a name for, the name will be

displayed for it, too.

Each time the 38 button is pressed, the characters to be

entered change as listed below.

Press the DISC+ or DISC– button to display the desired

character.

Characters that can be displayed are as follows.

• If you want to change the name of a disc, repeat steps 1 and 2

to display the name, and then repeat steps 3 and 4 to input the

changes.

• Pressing the reset button does not erase the disc names stored

in a disc changer.

Alphabet (upper case): A ~ Z

Alphabet (lower case): a ~ z

Numerals and symbols: 1~9 0 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]

Disc Name Preset Play (DNPP)

Special characters: á

Function of remote control with DNPP button

›

If you have preset the name of a disc that you want to listen to

in the disc changer, you can look for it by name and start

playing it.

— 22 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Switching Display for Discs

Switch the display that appears whilst discs are playing.

Press the DNPP button on the remote control.

"DNPP" will appear in the display, and the disc name preset play

mode is entered.

The names of all the discs in the disc changer will appear

successively in the display for five seconds each.

Discs whose names have not been preset will appear as "NO

NAME" in the display.

Switching Display for Discs:

Each time you press the DISP button, the display during disc

play switches as follows.

Track time

NOTE

• This function can only be used in disc changers that were

manufactured or sold as of 1997. Also note that some units

cannot provide a display unless the disc name preset has been

made by the unit that is playing.

• Discs in the disc changer that have never been played before

will appear as "NO ACCES" when the disc names are displayed.

When you cannot identify a disc because of the "NO ACCES"

display after inserting a disc magazine, try playing it using the

disc scan or a similar function to display the disc name.

Also note that "NO DISC" will be displayed when a disc has not

been loaded.

Disc name (DNPS)

Disc title (Units featuring CD text/MD only)

Track title (Units featuring CD text/MD only)

NOTE

• You can give names to discs through the presetting disc name

function (see p.22).

Note that depending on the unit, display may not be possible.

• If you try to display the name of a disc that does not have one,

"NO NAME" is displayed instead.

• When an attempt is made to display the title of a disc for which

a disc title/track title has not been recorded, the CD will display

"NO TEXT", the MD player built into this unit will display "NO

TITLE", and an MD changer will display "NO NAME/NO TITLE".

• Depending on the type of characters of the CD Text, some

characters may not be displayable.

Rapid display (forward / reverse):

Press the DISC+ or DISC– button.

Pressing the DISC+ button will rapidly display the preset

names/disc titles in order.

Pressing the DISC– button will rapidly display the preset

names/disc titles in reverse order.

When the name appears for the disc you want to play

Press the OK button.

The disc whose name is displayed will be recalled, and the disc

name preset play (DNPP) mode will end.

To cancel DNPP mode:

Press the DNPP button.

The disc name preset play (DNPP) mode will be cancelled.

— 23 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Other features

Release button

Audio Control Setting

Adjust various parameters of sound quality.

SRC FM/CLK

POWER

OFF

SRC

Press the AUD button to enter the control mode.

Egnlish

CLK

DISC

Press either the FM or AM button.

PTY

Each time the button is pressed, the adjustment mode will

change as follows:

NAME.S

TI VOL ADJ DISP

DISC

ATT

LOUD

SCAN

RDM

REP

D.SCN

M.RDM

Pressing the FM button advances the display, and pressing the

AM button reverses it.

AUD

AUD / MENU AM

Fader

Bass

Treble

Balance

NOTE

Source tone memory

Each source (MD, FM, AM, and disc changer) has its own

memory in which to store the bass and treble tone settings.

The settings made for a particular source are then recalled

automatically whenever you use that source (e.g., FM mode uses

the tone settings made for FM, AM for AM, etc.).

Clock display/

Graphic display

Press the 4/¢ button.

Look at the table to adjust the mode being displayed.

Adjustment

mode

Operation of Audio control button

4 button

Bass decreased.

¢ button

(Display)

Bass ("BAS")

Treble("TRE")

Balance("BAL")

Fader ("FAD")

Bass increased.

Treble decreased.

Left channel emphasized.

Rear channel increased.

Treble increased.

Right channel emphasized.

Front channel increased.

Press the AUD button to end the control mode.

— 24 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Switching Graphic Display

This function permits the graphic display to be switched to one

that is linked with the volume level value or to display various

modes. The initial setting is ON (displaying various modes).

Graphic display

Track time (Only during disc play)

Track number (Only during disc play)

Clock

Turning the Graphic Display On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Switching Graphic

Display function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "GRAP ON" or "GRAP OFF"

in the display, indicating that the Graphic display is on or off,

respectively.

Dimmer

You can dim the display.

"GRAP ON" (The graphic display works.)

NOTE

"GRAP OFF" (The graphic display does not work.)

The dimmer function is not available for units if the dimmer cable

is not connected.

Switching settings

Press either the AM button or FM button.

The display and setting will change.

Turning Dimmer On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the MENU button to end the menu mode.

Press the ¢ button repeatedly until the Dimmer function

appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "DIM ON" or "DIM OFF" in

the display, indicated that the current dimmer setting is on or

off, respectively.

Switching settings

Switching Display

You can change the display in each mode.

Press either the AM or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

Changing the Display:

Each time you hold down the CLK button for one second or

more, the display changes as follows:

— 25 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Other features

Illumination function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "COL GRN" or "COL AMB" in

the display, indicating that the current colour is green or amber,

respectively.

Automatic Dimmer Function

The display dims when the car's lights are turned on.

NOTE

Egnlish

The dimmer function is not available for units if the dimmer cable

is not connected.

Switching settings

Press either the AM button or FM button.

The display and setting will change.

Press the MENU button to end the menu mode.

TEL Mute

Shut down the audio system temporarily whenever an

incoming call is received.

Touch Sensor Tone

NOTE

This function produces a beep sound that accompanies button

operation. It can be switched on or off.

The function will not work if a cable is not connected to the car

phone.

Turning the Beep On/Off:

When the telephone rings:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

When a call is received, "CALL" is displayed and all the unit

functions are temporarily interrupted.

Restoring Original Unit Source During Phone Call:

Press the SRC button.

Press the ¢ button repeatedly until the Touch Sensor Tone

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "Beep ON" or "Beep OFF" in

the display, indicating that the current beep setting is on or off,

respectively.

"CALL" disappears from the display, and the volume of the

original source is restored gradually.

Turning TEL Mute Function Off After Phone Call:

Hang the phone up.

"CALL" disappears from the display.

Switching settings

Press either the AM or FM button.

The display and setting will change.

The original source (i.e., the one used before the phone call) is

returned to automatically, and the volume restored gradually.

Press the MENU button to end the menu mode.

NOTE

Selectable Illumination

The beep sound is not output from the preout jacks.

You can switch the colour of the button illumination between

green and amber.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Navigation Mute Function

When the KENWOOD Navigation System is connected, an

interruption of the audio guide results in the temporary

lowering of the audio level.

Press the ¢ button repeatedly until the Selectable

— 26 —

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE

Release button

The Navigation mute function cannot be used unless a TEL mute

cable is connected to the KENWOOD Navigation System.

POWER

SRC

OFF

CLK

DISC

PTY

NAME.S

DISP

DISC

ATT

LOUD

SCAN

RDM

REP

D.SCN

M.RDM

AUD

Contrast Adjustment

This adjustment permits easy viewing of the display.

NOTE

• The faceplate is a precision piece of equipment and can be

damaged by shocks or jolts. For that reason, keep the faceplate

in its special storage case whilst detached.

• Do not expose the faceplate or its storage case to direct

sunlight or excessive heat or humidity. Also avoid places with

too much dust or the possibility of water splashing.

To adjust the contrast:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Contrast Adjustment

function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "CONT ##" in the display,

indicating that the Contrast Adjustment mode is on.

Reattaching Faceplate:

Hold the faceplate so that the operation face faces the front

toward you and press until it locks. The faceplate will be set

and the unit will be operational.

Switching settings

Press either the AM or FM button.

Press the FM button to change the setting values higher, and

press the AM button to change them lower. Settings may be

made from 0 to 10.

Press the MENU button to end the menu mode.

NOTE

The "##" display in the contrast adjustment mode will differ

depending on the setting. The initial setting value is "5".

NOTE

When there is difficulty in setting the faceplate, align the

depression on the left side of the faceplate with the shaft of the

unit, then lock.

Theft Deterrent Faceplate

The faceplate of the unit can be detached and taken with you,

helping to deter theft.

Removing Faceplate:

Press the release button and drop open the faceplate.

In its dropped condition, whilst drawing the faceplate to one

side, pull it to the front and remove it.

Shaft

Depression

— 27 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Other features

Adjusting Time

Hold down either the AM or FM button for two seconds or

more to enter the Time Adjustment mode.

The time display will blink.

With automatic time adjustment, you can set the clock time

automatically according to time data sent from RDS stations

(after receiving RDS signals for several minutes). You can also

set the time manually if the automatic time adjustment function

is turned off. The factory default is automatic time adjustment.

Egnlish

• Adjusting the hours

Press the FM button to advance the hours, or press the AM

button to make the hours go back.

• Adjusting the minutes

Adjusting Time Automatically:

Press the ¢ button to advance the minutes, or press the

Tune into an RDS station for 3 or 4 minutes.

The time adjusts automatically to the correct local time.

4 button to make the minutes go back.

NOTE

Press the MENU button to end the menu mode.

The time is not adjusted when the RDS station you are tuned to is

not transmitting a time signal. Choose another RDS station in

such a case.

Disabled System Indicator (DSI)

A red indicator blinks on the unit after the faceplate is removed,

warning potential thieves. The factory default for this function

is "ON".

Turning Automatic Time Adjustment On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Automatic Time

Adjustment function appears in the display.

Press the 4 button to search in the other direction.

The function setting is indicated by "SYNC ON" or "SYNC OFF"

in the display, indicating that the Automatic Time Adjustment is

on or off, respectively.

Turning Disabled System Indicator On/Off:

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the Disabled System

Indicator function appears in the display.

"SYNC ON" (Automatic time adjustment)

Press the 4 button to search in the other direction.

The function setting is indicated by "DSI ON" or "DSI OFF" in the

display, indicating that the disable system indicator is on or off,

respectively.

"SYNC OFF" (Manual time adjustment)

Switching settings

Press either the AM button or FM button.

The display and setting will change.

Switching settings

Press the MENU button to end the menu mode.

Press either the AM button or FM button.

The display and setting will change.

Adjusting Time Manually:

Press the MENU button to end the menu mode.

Turn off the Automatic Time Adjustment as mentioned above.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the ¢ button repeatedly until the "CLK ADJ" appears in

the display.

Press the 4 button to search in the other direction.

— 28 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

External view

Number of items

2CAUTION

• If your car is not prepared for this special connection-system,

consult your Kenwood dealer.

..........................................1

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

• Make sure that all cable connections are securely made by

inserting jacks until they lock completely.

..........................................2

..........................................1

• If your vehicle's ignition does not have an ACC position, or if

the ignition cable is connected to a power source with constant

voltage such as a battery cable, the power will not be linked

with the ignition (i.e., it will not turn on and off along with the

ignition). If you want to link the unit's power with the ignition,

connect the ignition cable to a power source that can be turned

on and off with the ignition key.

2CAUTION

• If the fuse blows, first make sure that the cables have not

caused a short circuit, then replace the old fuse with one with

the same rating.

• Do not let unconnected cables or terminals touch metal on the

car or anything else conducting electricity. To prevent short

circuits, also do not remove the caps on the ends of the

unconnected cables or the terminals.

• Connect the speaker cables correctly to the terminals to which

they correspond. The unit may receive damage or fail to work if

you share the - cables and/or ground them to any metal part in

the car.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• Insulate unconnected cables with vinyl tape or other similar

material.

The use of any accessories except for those provided might result

in damage to the unit. Make sure only to use the accessories

shipped with the unit, as shown above.

Installation Procedure

1. To prevent short circuits, remove the key from the ignition and

disconnect the -terminal of the battery.

2. Make the proper input and output cable connections for each unit.

3. Connect the cable on the wiring harness.

4. Take Connector B on the wiring harness and connect it to the

speaker connector in your vehicle.

5. Take Connector A on the wiring harness and connect it to the

external power connector on your vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

• Some disc changers need conversion cables for connection.

See the section on "Safety Precautions" for details.

• If the console has a lid, make sure to install the unit so that the

faceplate does not hit the lid when closing and opening.

• Mount the unit so that the mounting angle is 30° or less.

8. Reconnect the - terminal of the battery.

9. Press the reset button.

— 29 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Cables to Terminals

Antenna Conversion Adaptor (ISO–JASO) (Accessory3)

FM/AM antenna

input

Antenna Cord (ISO)

Rear left output

(White)

Egnlish

Connector Function Guide

Fuse (10A)

Front left

output (White)

Pin Numbers for

Cable Colour

Functions

ISO Connectors

External Power

Connector

Front right

output (Red)

A–4

A–5

A–6

A–7

A–8

Yellow

Blue/White

Orange/White Dimmer

Red

Battery

Power Control

KENWOOD disc

changer / DAB

control input

Rear right

output (Red)

Ignition (ACC)

Earth (Ground)

Connection

Black

NOTE

To connect the Disc changer

or DAB unit, consult each

manual.

Wiring harness

(Accessory1)

Speaker

Connector

B–1

Purple

Purple/Black

Gray

Gray/Black

White

White/Black

Green

Rear Right (+)

Rear Right (–)

Front Right (+)

Front Right (–)

Front Left (+)

Front Left (–)

Rear Left (+)

Rear Left (–)

Connect to the terminal that is

grounded when either the

telephone rings or during

conversation.

TEL MUTE

B–2

B–3

B–4

B–5

B–6

B–7

B–8

TEL mute cable (Brown)

NOTE

To connect the KENWOOD

navigation system, consult

your navigation manual.

Battery cable (Yellow)

Ignition cable (Red)

If no connections are made,

do not let the cable come

out from the tab.

Green/Black

Connect either to the power

control terminal when using the

optional power amplifier.

A–7 Pin (Red)

P.CONT

A–4 Pin (Yellow)

Power control cable

(Blue/White)

Connector A

Connector B

— 30 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

■

Installation

2WARNING

Connecting the ISO Connector (see p.30)

The pin arrangement for the ISO connectors depends on the type

of vehicle you drive. Make sure to make the proper connections to

prevent damage to the unit.

Firewall or metal support

The default connection for the wiring harness is described in 1

below. If the ISO connector pins are set as described in 2 or 3,

make the connection as illustrated.

Screw (M4X8)

(commercially

available)

1 (Default setting) The A-7 pin (red) of the vehicle's ISO

connector is linked with the ignition, and the A-4 pin (yellow) is

connected to the constant power supply.

Unit

Vehicle

A–7 Pin (Red)

Bend the tabs of the

mounting sleeve with

a screwdriver or

similar utensil and

attach it in place.

Ignition cable (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

Self-tapping

screw

(commercially

available)

Metal mounting

strap

(commercially

available)

2 The A-7 pin (red) of the vehicle's ISO connector is connected to

the constant power supply, and the A-4 pin (yellow) is linked to

the ignition.

NOTE

Unit

Vehicle

Make sure that the unit is installed securely in place. If the unit is

unstable, it may malfunction (eg, the sound may skip).

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

3 The A-7 pin (red) of the vehicle's ISO connector is not

connected to anything, whilst the A-4 pin (yellow) is connected

to the constant power supply (or both the A-7 (red) and A-4

(yellow) pins are connected to the constant power supply).

Unit

Vehicle

Connect to a power source that can be

turned on and off with the ignition key.

Ignition cable (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

— 31 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

■

Removing the hard rubber frame

Removing the Unit

Refer to the section “Removing the hard rubber frame” and

then remove the hard rubber frame.

Engage the catch pins on the removal tool and remove the two

locks on the lower level.

Lower the frame and pull it forward as shown in the figure.

Remove the screw (M4×8) on the back panel.

Egnlish

Insert the two removal tools deeply into the slots on each side,

as shown.

Catch

Lock

Catch facing up

Screw (M4X8)

(commercially

available)

Accessory2 Removal tool

When the lower level is removed, remove the upper two

locations.

Lower the removal tool

toward the bottom, and pull

out the unit halfway whilst

pressing towards the

inside.

2CAUTION

Be careful to avoid injury from the catch pins on the removal tool.

NOTE

Pull the unit all the way out

with your hands, being

careful not to drop it.

The frame can be removed from the top side in the same

manner.

— 32 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before

calling service, first check the following table for possible problems.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the cables, replace the

fuse with one having the same rating.

No ACC position on vehicle ignition.

The Attenuator function is turned on.

Connect the same cable to the ignition as the battery cable.

Turn off the Attenuator function.

No sound can be heard, or the

volume is low.

The fader and/or balance settings are set all the way to

one side.

Reset the fader and/or balance settings.

The input/output cables or wiring harness are connected

incorrectly.

Reconnect the input/output cables and/or the wiring harness

correctly. See the section on "Connecting Cables to

Terminals".

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

Press the reset button on the unit (see page 4).

A speaker cable may be pinched by a screw in the car.

The speakers are not wired correctly.

Check the speaker wiring.

The sound quality is poor or

distorted.

Reconnect the speaker cables so that each output terminal

is connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull out the antenna all the way.

The antenna control cable is not connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The memory is erased when

the ignition is turned off.

The battery cable has not been connected to the proper

terminal.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The ignition and battery cable are incorrectly connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The TEL mute function does

not work.

The TEL mute cable is not connected properly.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The TEL mute function turns on

even though the TEL mute

cable is not connected.

The TEL mute cable is touching a metal part of the car.

Pull the TEL mute cable away from the metal part of the car.

MD mode cannot be set.

The faceplate was closed whilst the MD was being

ejected.

Press the eject(0) button and reinsert the MD.

The MD cannot be inserted.

The MD does not load.

There is already an MD loaded.

Eject the currently loaded MD and then load the new one.

Insert the MD in the proper orientation.

The insertion orientation of the MD is incorrect or the MD

is upside down.

— 33 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

PROBLEM

POSSIBLE CAUSE

SOLUTION

The MD loads but soon comes

out again.

Nothing is recorded on the MD.

Replace the MD with one that is recorded.

The sound skips.

The mounting angle exceeds 30°.

The mounting is unstable.

Adjust to an angle of less than 30°.

Egnlish

Anchor the unit securely. When the sound skips at the same

portion even when the car is stopped, the problem lies with

the MD.

There is noise during playback.

A track will not play.

The MD is soiled with dust or dirt.

Random play has been selected.

If another MD is played back and there is no problem, then

the problem is due to the sound quality of the MD itself.

Turn off random play.

External disc control mode

PROBLEM

POSSIBLE CAUSE

SOLUTION

The disc control mode cannot

be selected.

No cable has been connected to the disc changer input

terminal on the unit.

Connect the cable to the disc changer input terminal on the

unit.

The specified disc does not

play, but another one plays

instead.

The specified CD is quite dirty.

Clean the CD.

The CD is upside-down.

Load the CD with the labeled side up.

The disc is loaded in a different slot from that specified.

Eject the disc magazine and check the number for the

specified disc.

The disc is severely scratched.

Try another disc instead.

The sound skips.

Something is touching the disc changer.

The CD is scratched or dirty.

Remove whatever is touching it.

If skipping happens at the same place when the car is

stopped, something with the CD is wrong. Clean the CD.

The computer chip in the unit is not functioning normally.

Random play or magazine random play has been selected.

Press the reset button on the unit (see p. 4).

The display shows that the

changer is being played, but no

sound can be heard.

The specified track will not

play.

Turn off random play or magazine random play.

If the following situations, consult your nearest service center:

• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered when switching modes.

— 34 —

Download from Www.Somanuals.com. All Manuals Search And Download.

The following messages are displayed when certain problems are occurring in your system. Take the recommended

actions.

No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.

EJECT

] Load the disc magazine properly.

No CD in the unit.

] Insert the CD.

No disc has been loaded in the disc magazine.

NO DISC

E-04

] Load a disc into the disc magazine.

No disc has been loaded in the disc magazine.

] Load a disc into the disc magazine.

The CD is very dirty. The CD is upside-down. The CD is scratched a lot.

] Clean the CD and load it correctly.

Nothing has been recorded on the MD.

BLANK

NO TRACK

NO PANEL

E-77

] The next MD is automatically played back

No tracks are recorded on the MD, although it has a title.

] The next MD is automatically played back.

The faceplate of the slave unit being connected to this unit has been removed.

] Replace it.

The unit is malfunctioning for some reason.

] Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.

Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.

] Check the disc magazine. And then, press the reset button on the unit.

If the "E- 99" code does not disappear, consult your nearest service center.

E-99

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F), stopping

HOLD

all operation.

] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the

disc starts playing again.

Nothing has been recorded on the MD you are trying to play.

] Replace this MD with one that has been recorded.

The MD player section is not operating properly.

] Reinsert the MD. If the MD cannot be ejected or the display continues to flash even when the MD has been properly

reinserted, please switch off the power and consult your nearest service centre.

— 35 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Specifications subject to change without notice.

FM tuner section

Audio section

Frequency range (50 kHz Space)...............87.5 MHz – 108.0 MHz

Usable sensitivity (S/N = 26dB)..................................0.7 µV/75 Ω

Quieting Sensitivity (S/N = 46dB) ...............................1.6 µV/75 Ω

Frequency response ( 3.0 dB) ..............................30 Hz – 15 kHz

Signal to Noise ratio (MONO) ..............................................65 dB

Selectivity (DIN) ( 400 kHz)............................................. ≥ 80 dB

Stereo separation (1 kHz).....................................................35 dB

Maximum output power .................................................44 W × 4

Output power (DIN 45324, +B=14.4 V) ..........................28 W × 4

Tone action

Egnlish

Bass: ...........................................................100 Hz 10 dB

Treble: .........................................................10 kHz 10 dB

Preout level / load...............................................1800 mV / 10 kΩ

Preout Impedance............................................................≤ 600 Ω

MW tuner section

General

Frequency range (9 kHz Space)......................531 kHz – 1611 kHz

Usable sensitivity (S/N = 20dB)............................................25 µV

Operating voltage..............................14.4 V (11 – 16 V allowable)

Current consumption.............................................................10 A

Installation size (W × H × D) ...........................182 × 53 × 160 mm

Weight...............................................................................1800 g

LW tuner section

Frequency range..............................................153 kHz – 281 kHz

Usable sensitivity (S/N = 20dB)............................................45 µV

MD player section

Laser diode...........................................GaAlAs (λ=760 – 800 nm)

Digital filter (D/A)......................................8 Times Over Sampling

D/A Converter .......................................................................1 Bit

Frequency response ( 2 dB) .................................20 Hz – 20 kHz

Total harmonic distortion (1 kHz) .........................................0.5 %

Signal to Noise ratio.................................................90 dB (1 kHz)

Dynamic range ....................................................................90 dB

Channel separation..............................................................85 dB

Spindle speed ........................................................400 – 800 rpm

Wow & Flutter........................................Below Measurable Limit

— 36 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Ironman Fitness Exercise Bike 100125 User Manual
Jabra Bluetooth Headset BT2046 User Manual
John Deere Compact Loader 160G LC User Manual
John Lewis Freezer JLFZW 1806 User Manual
JVC Car Stereo System GET0260 015A User Manual
JVC Projector 5700 User Manual
Kenmore Refrigerator 2205960 User Manual
KitchenAid Refrigerator W10213162A User Manual
Kodak Digital Camera Z1085 IS User Manual
Kolcraft Stroller S64 R4 2 12 User Manual