Kenwood CD Player Z919 User Manual

MULTI CONTROLCD-RECEIVER

Z919

INSTRUCTION MANUAL

Take the tim e to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the

best perform ance from your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on

the warranty card, and in the space provided below. Refer to the model and serial

numbers whenever you call upon your KENWOOD dealer for information or service on

the product.

Model Z919 Serial number

01/12 11 10 9 8 7 6 5 4 3 2 1 00/12 11 10 9 8 7 6 5 4

Download from Www.Somanuals.com. All Manuals Search And Download.

2Warning

Safety precautions

NOTE

2CAUTION

2WARNING

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

Use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous

radiation exposure.

In compliance with Federal Regulations,

following are reproductions of labels on, or

inside the product relating to laser product

safety.

To prevent injury or fire, take the

following precautions:

• Insert the unit all the way in until it is fully

locked in place. Otherwise it may fall out of

place when jolted.

reasonable protection against harmful

interference in a residential installation. This

equipment may cause harmful interference

to radio communications, if it is not installed

and used in accordance with the instructions.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

• When extending the ignition, battery, or

ground wires, make sure to use automotive-

grade wires or other wires with a 0.75mm

KENWOOD CORPORATION

2967-3, ISHIKAWA-CHO,

HACHIOJI-SHI

(AWG18) or more to prevent wire

deterioration and damage to the wire coating.

• To prevent a short circuit, never put or leave

any metallic objects (such as coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• Be careful not to drop the unit or subject it to

strong shock.

TOKYO, JAPAN

KENWOOD CORP. CERTIFIES THIS EQUIPMENT

CONFORMS TO DHHS REGULATIONS N0.21 CFR

1040. 10, CHAPTER 1, SUBCHAPTER J.

Location : Bottom Panel

FCC WARNING

This equipment may generate or use radio

frequency energy. Changes or modifications

to this equipment may cause harmful

interference unless the modifications are

expressly approved in the instruction manual.

The user could lose the authority to operate

this equipment if an unauthorized change or

modification is made.

The unit may break or crack because it

contains glass parts.

NOTE

This Class B digital apparatus complies with

Canadian ICES-003.

— 3 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

Cleaning the Unit

2CAUTION

NOTE

If the front panel gets dirty, turn off the

power and wipe the panel with a dry silicon

cloth or soft cloth.

• The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the display

in the illustrations may differ from what

appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

• If you experience problems during

installation, consult your Kenwood dealer.

• If the unit does not seem to be working right,

try pressing the reset button first. If that does

not solve the problem, consult your Kenwood

dealer.

To prevent damage to the machine,

take the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

2CAUTION

Do not wipe the panel with a hard cloth or a

cloth dampened by volatile solvents such as

paint thinner and alcohol. They can scratch

the surface of the panel and/or cause the

indicator letters to peel off.

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision equipment.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

Cleaning the CD Slot

As dust tends to accumulate in the CD slot,

clean it every once in a while. Your CDs can

get scratched if you put them in a dusty CD

slot.

• To prevent a short circuit when replacing a

fuse, first disconnect the wiring harness.

• Do not place any object between the

faceplate and the unit.

• Do not use your own screws. Use only the

screws provided. If you use the wrong

screws, you could damage the unit.

Reset button

Lens Fogging

• The functions that can be used and the

information that can be displayed will differ

depending on the external disc players being

connected.

Right after you turn on the car heater in cold

weather, dew or condensation may form on

the lens in the CD player of the unit. Called

lens fogging, CDs may be impossible to play.

In such a situation, remove the disc and wait

for the condensation to evaporate. If the unit

still does not operate normally after a while,

consult your Kenwood dealer.

— 4 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on playing MP3 files

This unit can play MP3 files.

Note, however, that the MP3 file recording media and

formats acceptable are limited.

When writing MP3 files, pay attention to the following

restrictions.

Entering file and folder names

When entering file and folder names, use alphanumeric characters

only. If entered with any other character, the file and folder names are

not displayed correctly. They may neither be displayed correctly

depending on the CD writer used.

Note that the unit cannot display ID tags even though they have been

embedded in MP3 files.

The unit recognizes and plays only those MP3 files which have the

MP3 filename extension (.MP3). MP3 files should therefore be saved

with the MP3 extension.

Acceptable media

The MP3 file recording media acceptable to this unit are CD-ROM,

CD-R, and CD-RW.

Acceptable medium formats

Writing files into a medium

The medium formats acceptable to this unit are ISO 9660 Level 1 and

Level 2 excluding the extended formats. When reading an MP3 file

written in a format other than ISO 9660 Level 1 or Level 2, the unit

may fail to play the file normally or display the file or folder name

correctly.

The major specifications of ISO 9660 Level 1 and Level 2 are as

follows:

When a medium containing MP3 data is loaded, the unit checks all

the files on the medium. If the medium contains a lot of folders or

non-MP3 files, therefore, it takes a long time until the unit starts

playing MP3 files.

In addition, it may take time for the unit to move to the next MP3 file

or a file search or folder search may not be performed smoothly.

You should not write non-MP3 files or unneeded folders along with

MP3 files on the medium.

• Maximum number of directory levels: 8

2CAUTION

• Maximum number of files and folders per directory level:

253 (files and folders in total)

When playing MP3 files on a medium which also contains non-

MP3 files or folders, observe the following precautions. Loading

such a medium may produce loud noise to break the speakers.

• Do no attempt to play a medium containing a non-MP3 file

with the MP3 extension.

• Characters available to file and folder names:

A - Z, 0 - 9, _(underscore)

• Maximum number of characters in file names:

Level 1 : 12 (including a separator "." and a 3-character extension)

Level 2 : 31 (including a separator "." and a 3-character extension)

Settings for your MP3 encoder and CD writer

The unit mistakes non-MP3 files for MP3 files as long as they

have the MP3 extension.

• Do not attempt to play a medium containing non MP3 file.

When you use your MP3 encoder to compress audio data to an MP3

file, set the transfer bit rate of the encoder to fixed 128 kbps.

When you use your CD writer to record MP3 files up to the maximum

disc capacity, disable additional writing. For recording on an empty

disk up to the maximum capacity at once, check Disc at Once.

— 5 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on playing MP3 files

MP3 file playing order

When a file search is executed with file

being played ...

When selected for play, folder search, file search, or for folder select,

files and folders are accessed in the order in which they were written

by the CD writer.

Because of this, the order in which they are to be recorded does not

match the order in which they are played. You may be able to set the

order in which MP3 files are to be played by writing them onto a

medium such as a CD-R with their file names beginning with play

sequence numbers such as "01" to "99", depending on your CD writer.

Operation ofthe button

Current

file num ber

¢ Button

4 Button

Beginning of

file

When a folder search is executed with file

being played ...

currently being

played, the unit selects folders as shown below, starting with

For example, a medium with the following folder/file hierarchy is

subject to folder search, file search, or folder select as shown below.

folder

Current

foldernum ber

Operation ofthe button

FM Button

AM Button

Folder

File

Root

Virtualfolder

Exam ple ofa m edium 'sfolder/file hierarchy M edium 'svirtualfolder/file hierarchy

fora folderselect

Fora file search orfoldersearch

When folder select is selected with file

move from folder to folder ...

being played to

During folder select, a virtual folder is created one hierarchical level

below each folder. The hierarchy is displayed as if the MP3 file

(1)

recorded in each folder were placed in that virtual folder.

(2)

When the unit enters the folder select mode with file

being

（4）

played, it selects folders as shown below, starting with folder

(virtual folder

(3)

(4)

Operation ofthe button

¢ Button AM Button

Current

foldernum ber

4 Button

FM Button

(5)

(6)

（4）

(7)

(8)

(9)

Level1 Level2 Level3 Level4 Level5

— 6 —

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE

• Each virtual folder is displayed with the original folder name

bounded by parentheses " ( ) ". For example, the virtual folder

below the folder named " 4 " is displayed with a name of " (4) ".

The file name of each virtual folder is displayed with up to 29

characters (in the ISO 9660 Level 2 format) or 10 characters (in

the ISO 9660 Level 1 format), excluding the binding

parentheses.

• The FM button is disabled in a folder because it has no

subordinate hierarchical level below. Immediately after

entering the folder select mode as in the above example,

therefore, the FM button cannot be used as there is no

（4）

hierarchical level below folder

Once you have moved to folder

using the folder select

function, for example, you can use the FM button to select

（1）

folder

one level below.

— 7 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Handling Compact discs

• Remove CDs from the unit when not

listening to them for a while, and put them

back in their cases. Do not pile up CDs that

are removed from their cases or prop them

against something.

Playing a CD that is dirty, scratched or

warped can cause the sound to skip

and the unit to operate incorrectly,

resulting in worsened sound quality.

Take the following precautions to

prevent your CDs from getting

scratched or damaged.

Removing the CD

Only remove the CD from the machine in a

horizontal direction, holding it flat. You may

damage the surface of the CD if you try

pulling it down as it ejects.

Cleaning CDs

If a CD has gotten dirty, wipe it off gently

using a commercially available cleaning cloth

or a soft cotton cloth, starting from the

center of the disc and moving outward. Do

not clean CDs with conventional record

cleaners, anti-static formulas, or chemicals

such as paint thinner or benzene.

Handling CDs

• Do not touch the recorded side of the CD

(the side opposite the label) when holding it.

Do Not Use Special Shape CDs

• Be sure to use round shape CDs only for this

unit and do not use any special shape CDs.

Use of special shape CDs may cause the

unit to malfunction.

• The reflective film on a CD-R or a CD-RW is

more fragile than that on an ordinary music

CD, and may peel off if scratched.

Fingerprints on a CD-R or CD-RW are also

more likely to cause skipping when the disc

is played. For these reasons, handle the disc

very carefully.

Detailed handling instructions will appear on

the CD-R or CD-RW package: read this

information carefully before using the disc.

Checking New CDs for Burrs

When playing a new CD for the first time,

check that there are not any burrs stuck to

the perimeter of the disc or in the central

hole. CDs with burrs stuck on them may not

load properly or may skip while playing.

Remove burrs using a ballpoint pen or a

similar utensil.

• Do not use any CD which does not bear one

of the following marks:

•CD-Rs and CD-RWs which have not

• Do not stick tape on either side of the CD.

undergone finalization processing cannot be

played. (For more information on finalization

processing, refer to the manual for your CD-

R/CD-RW writing software or CD-R/CD-RW

recorder.) Additionally, depending on the

recording status, it may prove impossible to

play certain CDs recorded on CD-R or CD-RW.

Burrs

Tape

Burrs

Storing CDs

• Do not store CDs in areas exposed to direct

sunlight (such as a car seat or the

dashboard) or other hot places. A CD-R or

CD-RW is more susceptible than a music CD

to damage from high temperatures and

humidity, and in some cases, may become

unusable if left in the car for long periods of

time.

Do Not Use CDs with Sticker on the

Labeled Side

Do not use the CD with the label sticker

stuck on it.

Using such a CD may cause the CD to be

deformed and the sticker to peel off,

resulting in malfunction of the unit.

Do Not Load CD Accessories

Do not use commercially available CD

accessories that can be loaded into the CD

slot, such as stabilizers, protective sheets, or

CD cleaning discs, since they can cause the

unit to malfunction.

— 8 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Power

AUD/

LOUD

Turning on the power:

ANG

Press the SRC (source) button.

NOTE

Turn the power on before carrying out the following procedures.

Turning off the power:

Press the PWR OFF button for at least one second.

Selecting standby mode:

Press the SRC button repeatedly and switch to "ALL OFF".

When "ALL OFF" is displayed, the standby mode is activated.

The standby mode turns all functions off while leaving the

power to the unit on. Use this mode when you want to have

the display illuminated but don't want to listen to anything.

S.A

SRC/

PWR OFF

S/S

#1 - 6

CLK/

ADJ

Switching Modes

Switching Modes:

Each time you press the SRC (source) button, the mode

switches as follows:

LOUD indicator

Setting display

Tuner mode

CD/MP3 mode

External disc control modeMM

External TV control modeMM

Clock display

Standby modeMM

Round sound level indicator

indicator

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc and TV control mode will differ depending on

the unit that is connected.

• MP3 files can be played only on this unit.

— 9 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

• When the front panel has been slid, it might interfere with the

shift lever or something else. If this happens, pay attention to

safety and move the shift lever or take an appropriate action,

then operate the unit.

Volume

Increasing Volume:

Press the u button to turn up the volume.

• Do not apply excessive force to the front panel after it slides.

Decreasing Volume:

NOTE

Press the d button to turn down the volume.

Protect function for the panel

The panel may move due to the protection mechanism, if any

buttons are pressed with excessive force while the panel angle is

adjusted to the slide position.

Loudness

This function amplifies low and high tones when the volume is

turned down.

The LOUD indicator lights up when the loudness function is on.

Clock Adjustment

Adjust the clock.

Turning Loudness On/Off:

Press the LOUD button for at least one second to switch the

loudness on and off.

Press the CLK button to select the clock mode.

Once the clock mode is selected, "CLOCK" will be displayed.

Adjusting the Clock:

Press the ADJ button for at least two seconds.

"CLOCK ADJ" is displayed, and then you can adjust the time.

Panel Angle Adjustment

You can adjust the front panel angle for easy viewing.

You can adjust hours with the FM/AM button, and minutes with

the 4/¢ button.

NOTE

Sliding the panel:

To set the minute to "00"

Each time you press the ANG button for at least one second,

the front panel will slide to three positions step by step.

Press the S/S button for at least one second to set the minute to

"00".

Pressing this button while the minute is below "30" rounds it off,

and while the minute is "30" or more rounds it up.

NOTE

If the power is turned off, the front panel will close automatically.

When you turn the power back on, the panel angle will return to

the adjusted angle position.

Press the CLK button to end the clock adjustment.

Adjusting the minute restarts the second counter from 00.

Closing the panel:

Press the ANG button for at least one second repeatedly until

the front panel closes.

2CAUTION

• Take care that your fingers and so on do not get caught during

the slide operation of the front panel.

— 10 —

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE

Stopwatch

You can use the clock as a stopwatch.

To set the time to "0:00"

Press the S/S button for at least one second to return the time to

"0:00".

Press the CLK button to select the stopwatch mode.

Once the stopwatch mode is selected, "STOP WATCH" will be

displayed.

When you enter the stopwatch mode, the round sound level

indicator changes its display to indicate the stopwatch mode.

Press the CLK button to end the time setting for timer.

To start the timer

Each time you press the S/S button, the timer will start and

stop.

When you start the timer, the indicator will light up and the

To start the measurement

time counting will start.

Press the S/S button.

NOTE

If you want to clear the setting time of the timer

To stop the measurement

Press the S/S button.

Press the S/S button for at least one second.

Then the setting time of the timer will return to the time set in the

step 3.

NOTE

If you want to clear the time

Press the S/S button for at least one second.

Then the time indication will return to "0:00'00"0".

When the time set in the step 3 has passed

The timer will beep for five seconds.

To restart the measurement

Press the S/S button to restart the measurement.

You can immediately stop the beep by pressing the S/S button,

or leave it without any action for about 5 seconds.

Timer

You can use the clock as a timer. Once you set a time, the timer

will beep when the set time has past.

Press the CLK button to select the timer mode.

Once the timer mode is selected, "TIMER" will be displayed.

When you enter the timer mode, the round sound level indicator

changes its display to indicate the timer mode.

Time Setting:

Press the ADJ button for at least two seconds.

"TIMER ADJ" is displayed, and then you can set a time for the

timer.

You can adjust hours with the FM/AM button, and minutes with

the 4/¢ button.

— 11 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Alarm

Display Font Setting

You can change the font used on the display.

You can use the clock as an alarm. The alarm will beep on the

time set.

Changing the display font:

Press the S.A button for at least one second to toggle between

the normal font and funky font.

Press the CLK button to select the alarm mode.

Once the alarm mode is selected, "ALARM" will be displayed.

Time Setting:

Press the ADJ button for at least two seconds.

"ALARM ADJ" is displayed, and you can set a time for the alarm.

You can adjust hours with the FM/AM button, and minutes with

the 4/¢ button.

Switching the Round Indicator for the Sound Level

You can change the display mode of the round sound level

NOTE

To set the minute to "00"

indicator to the left of the display.

Press the S/S button for at least one second to set the minute to

"00".

Changing the round sound level indicator:

Press the S.A button to cycle through the round sound level

indicator as shown below:

Pressing this button while the minute is below "30" rounds it off,

and while the minute is "30" or more rounds it up.

Press the CLK button to end the time setting for alarm.

ANDROMEDA

RIPPLE

To start the alarm

Press the S/S button to switch the alarm on and off.

When you turn the alarm on, the indicator will light up.

COSMOS

THE POLESTAR

PULSAR

When the time set in the step 3 has come

The alarm will beep for 15 seconds.

You can immediately stop the beep by pressing the S/S button,

or leave it without any action for about 15 seconds.

COMET

NOTE

• You cannot switch the round sound level indicator when Silent

display in the function set is on.

Automatic Dimmer Function

The display dims when the car's lights are turned on.

Set Silent display in the function set to off before you change

the round sound level indicator.

NOTE

• You cannot switch the round sound level indicator when the

clock display is in the stopwatch mode and the timer mode.

The dimmer function is not available for units if the dimmer wire

is not connected.

— 12 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Audio Control Setting

Adjust various parameters of sound quality.

"KEX.P." : Recalling the kenwood preset sound setting

Press the preset buttons (#1-6).

Setting values: #1;Flat, #2;Rock, #3;Top40, #4;Jazz, #5;Easy,

#6;Scan of #1-5

Press the AUD button repeatedly and switch the display to

“AUDIO CTRL” to enter the audio control mode.

Pressing the button cycles through Audio control mode,

Crossover control mode, and Control mode off.

NOTE

• This mode is available only when the Sound coordinate system

is on. (page 35)

• You can call the following settings with this function; bass

center frequency, bass level, bass quality factor, bass extension,

treble center frequency, and treble level setting.

Selecting mode

Press either the FM or AM button.

Each time the button is pressed, the adjustment mode will

change.

Please refer to the following for the contents of the adjustment

modes.

NOTE

Source tone memory

Each source ( CD, FM, AM and disc changer ) has its own

memory in which to store the KEX.P, bass center frequency, bass

level, bass quality factor, bass extension, treble center frequency,

and treble level settings.

The settings made for a particular source are recalled

automatically whenever you use that source ( for example, FM

mode uses the tone settings made for FM, AM for AM, etc.).

"BASS f" : Adjust the center frequency of the bass.

Setting values: 60 / 70 / 80 / 100 (Only when the bass quality

factor is set to 1.00, 1.25 or 1.50) / 150 (Only when the bass

quality factor is set to 2.00) Hz

NOTE

This mode is available only when the Sound coordinate system is

on. (page 35)

Adjust each mode

Press the 4/¢ button.

Please refer to the following for the adjusting values.

Press the AUD button twice to end the audio control mode.

"BASS" : Adjust the bass level.

Setting values: - 6 – + 6

"BASS Q" : Adjust the Bass quality factor.

Setting values: 1.00 / 1.25 / 1.50 / 2.00

NOTE

This mode is available only when the Sound coordinate system is

on. (page 35)

— 13 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

"BASS EXT" : Switch the Bass Extend mode on/off.

"N-F LV" : Adjust the Non-fading output level.

Setting values: ON / OFF

Setting values: - 35 – + 5

(When the bass extend mode is set to on, low

frequency response is extended by 20%.)

NOTE

This mode is available only when the Sound coordinate system is

on. (page 35)

"AMP CTRL" : Set the amplifier bass increment.

Setting values: OFF/1/2

NOTE

As of December 1998, the power amplifiers controllable by the

main unit are as follows:

KAC-X501F/PS501F/X401M/PS401M/X301T/PS301T/X201T/PS201T

"TRE f" : Adjust the center frequency of the treble.

Setting values: 10.0 / 12.5 / 15.0 / 17.5 kHz

NOTE

This mode is available only when the Sound coordinate system is

on. (page 35)

Storing your sound settings:

Press a preset button (#1-6) for at least two seconds except

during the bass center frequency, bass level, bass quality

factor, bass extension, treble center frequency, and treble level

adjust mode.

"TREBLE" : Adjust the treble level.

NOTE

Setting values: - 6 – + 6

• This mode is available only when the Sound coordinate system

is on. (page 35)

• The settings you can preset are, bass center frequency, bass

level, bass quality factor, bass extension, treble center

frequency, and treble level.

"BALANCE" : Adjust the balance level.

Setting values: Left 15 – Right 15

Recalling your sound settings:

Press a preset button (#1-6) except during the bass center

frequency, bass level, bass quality factor, bass extension,

treble center frequency, and treble level adjust mode.

"FADER : Adjust the fader level.

Setting values: Front 15 – Rear 15

NOTE

This mode is available only when the Sound coordinate system is

on. (page 35)

— 14 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Digital Crossover Network

Adjust various parameters of the Crossover network.

"HPF R" : Adjust the frequency of the High-pass filter for rear

output.

Setting values: THROU / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz /

150Hz / 180Hz / 220Hz

Press the AUD button repeatedly and switch the display to

“X’OVER CTRL” to enter the Crossover network control mode.

Pressing the button cycles through Audio control mode,

Crossover control mode, and Control mode off.

NOTE

You can separately set the high-pass filter for front and rear

output, including preouts. The high-pass filter does not affect the

non-fading preout.

Selecting mode

Press either the FM or AM button.

Each time the button is pressed, the adjustment mode will

change.

Please refer to the following for the contents of the adjustment

modes.

Adjust each mode

"LPF NF" : Adjust the frequency of the Low-pass filter for Non-

Fading output.

Press the 4/¢ button.

Please refer to the following for the adjusting values.

Setting values: 50 Hz / 80 Hz / 120 Hz / THROU

Press the AUD button once to end the Crossover network

control mode.

"PHASE : Adjust the phase for Non-Fading output.

Setting values: NOR (0°) / REV (180°)

"HPF F" : Adjust the frequency of the High-pass filter for front

output.

Setting values: THROU / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz /

150Hz / 180Hz / 220Hz

NOTE

Storing your settings of the Crossover network:

You can separately set the high-pass filter for front and rear

output,including preouts. The high-pass filter does not affect the

non-fading preout.

Press a preset button (#1-6) for at least two seconds.

Recalling your settings of the Crossover network:

Press a preset button (#1-6) for the desired Crossover network

setting.

— 15 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

Tuning

FM/

AME

Press the SRC (source) button repeatedly to select the tuner

mode. "TUNER" is displayed when the tuner mode has been

selected.

DISP/

NAME.S

Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2, and FM3.

Press the AM button to select the AM band.

• Auto Seek Tuning

Press the ¢ button for at least half a second to seek higher

frequencies.

Press the 4 button for at least half a second to seek lower

frequencies.

#1 - 6

AM/

CRSC

SRC

• Manual Tuning

Press the ¢ button to increase the frequency by one step.

Press the 4 button to decrease the frequency by one step.

NOTE

The ST indicator lights up when stereo broadcasts are being

received.

Preset station number

Frequency

Band display

indicator

Station Preset Memory

Store the frequency of a station. You can then recall that

station with a single touch of a button.

Select the band/station that you want to have stored.

Press the button (#1-6) that you want to use for the station, for

at least two seconds.

The button number blinks once in the display to indicate that

the data has been stored.

ST indicator

NOTE

You can store six stations in each of the FM1, FM2, FM3, and AM

bands.

— 16 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Memory Entry

Clean Reception System Circuit (CRSC)

Temporarily have reception switched from stereo to mono to

reduce multi-path noise when listening to the FM station.

The factory default for this function is ON.

You can automatically store all the receivable frequencies in

the band currently being listened to, and then recall them with

the touch of a button later. This function is especially useful

when you are travelling and do not know what stations are

available. Up to six frequencies can be stored this way.

Turning CRSC On/Off:

Press the CRSC button for at least one second to turn the

function on/off.

Select the band for auto memory entry.

When the CRSC is turned on, the

indicator lights off.

Press the AME button for at least two seconds to start auto

memory entry.

NOTE

The numbers of the preset station buttons are shown in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

Strong electrical fields (such as from power lines) may cause

unstable sound quality when CRSC is turned on. In such a

situation, turn it off.

Switching Display for Tuner

You can change the display used when listening to the radio.

Preset Tuning

You can recall a station being preset in preset station buttons

(#1-6).

Changing the Display:

Each time you press the DISP button, the display changes as

follows:

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Station frequency

SNPS name (only when being preset)

— 17 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

NOTE

Station Name Preset (SNPS)

You can assign names to radio stations with the Station Preset

Memory. Up to 30 stations can be assigned names.

Direct Alphabet Input (Function of remote)

You can directly input letters using the number/letter entry

buttons on the remote.

Example: Use the following table to enter the name "DANCE".

Adjust the frequency to the station whose name you want to

enter.

Button to press

# Times pressed

Character

“D”

“A”

“N”

“C”

“E”

Press the NAME.S button for at least two seconds.

“NAME SET” is displayed once the station name preset mode

is entered.

The cursor will blink in the position where letters are entered.

Press either the 4 or ¢ button to move the cursor to the

desired position.

The 4 button moves the cursor to the left, and the ¢

button to the right.

Continue steps 3 and 4 until all the characters are chosen for

the name.

You can also move the cursor left or right by pressing the 4

or ¢ buttons, respectively, on the remote.

NOTE

Each time the 38 button is pressed, the characters to be

entered change as listed below.

Press the FM or AM button to display the desired character.

Characters that can be displayed are as follows:

You can enter up to 12 characters for each name.

Assigning Names

Press the NAME.S button on the unit or the OK button on the

remote.

The name of the station is stored in memory, and the Station

Name Preset mode ends.

Alphabet(uppercase):A -Z 0 -9 !"# $ % & '()

＊ + , -. /:;< = > ? @ [¥ ]^「」・

Also, if you make no input for 10 seconds, the name will be

stored up to the point that you have entered, and the mode

ends.

Alphabet(lowercase):a -z 0 -9 !"# $ % & '()

＊ + , -. /:;< = > ? @ [¥ ]^「」・

NOTE

• You can assign names up to 30 FM/AM stations in all.

• Station names remain stored even if the reset button is pressed.

• If you want to change the name of a station, first display the

name of the station (following steps 1 and 2 above), then

change the letter(s) that you want by following steps 3 and 4.

• Removing this unit from the battery power supply erases station

names.

— 18 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Station Name Preset Play (SBF)

(Function of Remote)

(See page 35)

Direct Access Tuning

(Function of Remote)

(See page 35)

You can search for the station for any station if its name has

been preset using Station Name Preset.

Use the remote to select frequencies directly.

Select the band by pressing the FM or AM button.

Press the SBF button.

Press the DIRECT button.

“SBF MODE” will be displayed once the station name preset

play mode is entered.

In the display, "----" blinks for 10 seconds.

If you make no input in the 10-second period, direct access

tuning is automatically canceled.

The names of the stations stored in the band currently listened

to are displayed in the following order for five seconds each:

Enter the frequency of the desired station while the display is

blinking.

= FM1 Ô FM2 Ô FM3 Ô AM +

Each time you press the ¢ button, the station display

switches in the forward direction.

If you want to listen to an FM station at 92.1 MHz, for example,

press 9, 2, and 1.

Each time you press the 4 button, the station display

switches in the reverse direction.

If you want to listen to an AM station at 530 kHz, for example,

press 5, 3, and 0.

Stations whose names have not been stored will be displayed

as frequencies.

NOTE

You cannot enter frequencies above or below what a band can

receive.

NOTE

Changing the Displayed Band

Pressing the FM button switches between the FM1, FM2, and

Canceling Direct Access Tuning:

FM3 displays, in that order.

Press the DIRECT button again.

Pressing the AM button switches to the AM display.

Once the name is displayed for the station you want to listen

Press the OK button.

Reception starts of the displayed station, and the Station Name

Preset Play mode ends.

— 19 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/External disc control features

NOTE

DISP/

For playing MP3 files, see "MP3 features" (page 27).

NAME.S

FM/

DISC+

Playing CDs

Play:

Press the 0 button to slide open the front panel, showing the

CD (insertion) slot. Holding the CD with the labeled side facing

up, insert it in the slot.

The front panel will close, and the CD will start playing.

The

indicator will light up when a CD has been inserted.

AM/

DISC-

TIME

RDM

D.SCN

REP

SCN

SRC

M.RDM

Playing CDs Already Inserted:

Press the SRC button repeatedly to select the CD mode.

"CD" is displayed when the CD mode has been selected.

The CD will start playing.

Mode display

indicator

Pausing and Restarting CD Play:

Playing time

Track number

Press the 38 button to make the disc pause.

Press the same button again to start play again.

Eject:

Press the 0 button. The front panel will slide to eject the CD.

Press the 0 button to close the front panel.

2CAUTION

REP indicator

DISC indicator

RDM indicator

SCN indicator

• Do not attempt to insert a CD into the slot if another one is

already there.

• When the front panel has been slid, it might interfere with the

shift lever or something else. If this happens, pay attention to

safety and move the shift lever or take an appropriate action,

then operate the unit.

• Do not apply excessive force to the front panel after it slides.

• Do not use the unit with the front panel in the slid condition.

Doing so will cause breakdown.

— 20 —

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE

Fast Forwarding and Reversing Disc Play

When you load a CD and eject it right away, the next time you try

to insert the CD may not load. In such a situation, take the CD out

for a moment and then reinsert it.

Fast Forwarding Disc Play:

Hold down on the ¢ button.

Release your finger to play the disc at that point.

Reversing Disc Play:

Hold down on the 4 button.

Release your finger to play the disc at the point.

Playing Other Disc Mode

This function permits the connection of optional players and

the playing of discs other than the loaded CD (in the current

unit).

Track Search

Search forward or backward through the tracks on the disc until

you reach the one that you want to listen to.

Playing Discs:

Press the SRC button repeatedly to select the external disc

control mode.

The disc will start playing.

NOTE

Making a Backward Track Search:

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current track,

twice to search back to the beginning of the previous track, and

so forth.

The external disc control mode will differ, depending on the unit

that is connected.

Mode Display Examples

• "CD 2"...when a CD player is connected

• "CDCH"...when a disc changer is connected

• "CDCH 1", "CDCH 2"...when two disc changers are connected

Play starts at the beginning of the displayed track number.

NOTE

(For disc changers)

Pressing the 4 button while listening to track 1 will only search

back to the beginning of that track. The reverse search is not

"recycled" to the last track on the disc.

Pausing and Restarting Disc Play:

Press the 38 button to make the disc pause.

Press the same button again to start play again.

Making a Forward Track Search:

NOTE

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

(For disc changers)

When one disc has finished playing its last track, the next disc in

the changer will start playing. When the last disc in the changer

has finished, the player will return to the first disc and start

playing it.

Play starts at the beginning of the displayed track number.

NOTE

(For disc changers)

You cannot make a forward track search when listening to the last

track on a disc.

— 21 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/External disc control features

NOTE

Disc Search

(Function of disc changers)

Repeat play is canceled when you eject the disc.

Search forward or backward through the discs in a disc

changer.

Making a Backward Disc Search:

Track Scan

Press the DISC– button to display the desired disc number.

Each time the button is pressed, the displayed disc number

decreases by one.

Successively play the beginning of each track on a disc until

you find the track that you want to listen to.

Play starts at the beginning of the displayed disc.

Starting the Track Scan:

Making a Forward Disc Search:

Press the SCN button. The SCN indicator lights up and the first

10 seconds of each track will be played, in order.

The track number currently being heard blinks in the display.

Press the DISC+ button to display the desired disc number.

Each time the button is pressed, the displayed disc number

increases by one.

Stopping to Listen to the Track Being Scanned:

Press the 38 or SCN button again to stop the scan and keep

on listening to a track normally.

Play starts at the beginning of the displayed disc.

NOTE

"Load" is displayed when discs are being exchanged on the disc

changer.

NOTE

• The track scan function is canceled when you eject the disc.

• The track scan function only scans each track on a disc once.

Track Repeat

Repeat playing the track currently being listened to.

Disc Scan

(Function of disc changers)

Successively play the beginning of each disc on a changer until

you find the one that you want to listen to.

Turning Track Repeat Play On/Off:

Press the REP button to switch track repeat play on and off.

The REP indicator lights up when track repeat play is turned on.

Starting the disc scan:

Press the D.SCN button. The DISC SCN indicator lights up and

the first 10 seconds of each disc will be played, in the order

they are loaded on the changer.

NOTE

Repeat play is canceled when you eject the disc.

The disc number currently being heard blinks in the display.

Stopping to Listen to the Disc Being Scanned:

Press the 38 or D.SCN button again to stop the scan and keep

on listening to the disc normally.

Disc Repeat

Repeat playing the disc currently being listened to.

(Function of disc changers)

NOTE

• The disc scan function is canceled when you eject the disc.

Turning Disc Repeat Play On/Off:

Press the REP button for at least one second to switch disc

repeat play on and off.

• The disc scan function only scans each disc on the changer

once.

• "Load" is displayed when discs are being exchanged on the disc

The DISC REP indicator lights up when disc repeat play is

turned on.

changer.

— 22 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Random Play

Play all the tracks on the current disc in random order.

Text Scroll

This function permits the text to be scrolled and the entire text

to be displayed.

Press the RDM button to switch random play on and off.

The RDM indicator lights up when random play is turned on.

The track number will change over and over in the display as

the next track is being selected.

Turning the Text Scroll on/off :

Press the TIME button for at least one second to switch the

Text Scroll on and off.

When the track has been selected, play will begin.

When the Text Scroll is turned on:

The text display will be scrolled repeatedly.

NOTE

(For disc changers)

When all the tracks on a certain disc have been played using

random play, the next disc on the changer will start playing using

the same function.

When the Text Scroll is turned off:

The text display will be scrolled once each time when it is

switched over.

To change the track being heard, press the ¢ button.

Another track will be selected and played.

NOTE

Random play is canceled when you eject the disc.

Direct Track Search

(Function of Remote)

(See page 35)

Using the remote, directly input the track number that you want

to listen to.

Magazine Random Play

(Function of disc changers)

Play the tracks on all the discs in the disc changer in random

Using the number buttons on the remote, input the number of

the track that you want to listen to.

order.

The selected track number will blink in the display for 10

seconds.

Press the M.RDM button to switch magazine random play on

and off.

The DISC RDM indicator lights up when magazine random play

is turned on.

If you make no further input in the 10-second period, the

number entry mode will automatically be canceled.

Press either the 4 or ¢ button while the track number is

blinking.

The track starts playing.

The disc and track numbers will change over and over in the

display as the next track is being selected.

When the disc/track has been selected, play will begin.

Canceling Direct Track Search While It Is Operating:

To change the track being heard, press the ¢ button.

Another disc/track will be selected and played.

Press the 38 button.

NOTE

You cannot use the direct track search function while doing track

or disc scans or using random or magazine-random play.

• Magazine random play is canceled when you eject the disc.

• The time needed for random selection depends on the number

of discs loaded in the disc magazine.

— 23 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/External disc control features

Direct Disc Search (Function of disc changers with remote)

Each time the 38 button is pressed, the characters to be

entered change as listed below.

Press the FM or AM button to display the desired character.

Characters that can be displayed are as follows:

(See page 35)

Using the remote, directly input the disc number that you want

to listen to.

Using the number buttons on the remote, input the number of

the disc that you want to listen to.

Alphabet(uppercase):A -Z 0 -9 !"# $ % & '()

＊ + , -. /:;< = > ? @ [¥ ]^「」・

The selected disc number will blink in the display for 10

seconds.

Alphabet(lowercase):a -z 0 -9 !"# $ % & '()

＊ + , -. /:;< = > ? @ [¥ ]^「」・

If you make no further input in the 10-second period, the

number entry mode will automatically be canceled.

NOTE

Direct Alphabet Input (Function of remote)

• Input "0" to select disc 10.

• If you input more than two numbers all at once, a search will be

made only of the last number input.

You can directly input letters using the number/letter entry

buttons on the remote.

Example: Use the following table to enter the name "DANCE".

^{Press either the DISC}+ or DISC– button while the number

Button to press

# Times pressed

Character

inputted is blinking.

The disc starts playing.

“D”

“A”

“N”

“C”

“E”

Canceling Direct Disc Search While It Is Operating:

Press the 38 button.

Presetting Disc Names

Store the names of discs to be displayed when played.

Continue steps 3 and 4 until all the characters are chosen for

the name.

Play the disc whose name you want to preset.

Press the NAME.S button for at least two seconds.

NOTE

"NAME SET" is displayed and the disc name preset mode is

You can enter up to 12 characters for each name.

entered.

The cursor blinks in the position where character input can be

made.

Assigning Names

Press the NAME.S button on the unit or the OK button on the

remote.

Press either the 4 or ¢ button to move the cursor to the

desired position.

The disc name is stored and the disc name preset mode is

canceled.

The 4 button moves the cursor to the left, and the ¢ button

to the right.

If you make no entry in a 10-second period, the name will be

stored with the characters input so far.

You can also move the cursor left or right by pressing the 4

or ¢ buttons, respectively, on the remote.

— 24 —

Download from Www.Somanuals.com. All Manuals Search And Download.

• If you try to display the name of a disc that does not have one,

"NO NAME" is displayed instead.

NOTE

• You can register up to 10 disc names in this unit, up to 100 disc

names in the CD changer C907, up to 10 disc names in the

TV/CD player VZ907 respectively.

• Discs are identified by their total length and number of tracks. If

another disc happens to have the same specifications as one

that you have already stored a name for, the name will be

displayed for it, too.

• When there is an attempt to display the text of a disc for which

the disc text/track text has not been recorded, "NO TEXT" is

displayed.

• Depending on the type of characters of the CD text, some

characters may not be displayed.

• If you want to change the name of a disc, repeat steps 1 and 2

to display the name, and then repeat steps 3 and 4 to input the

changes.

• Disc names remain stored even if the reset button is pressed.

• Removing this unit from the battery power supply erases disc

names.

Switching Playing Time Display

Switch the playing time display that appears while the playing

time display is selected.

Switching Playing Time Display:

Each time you press the TIME button, the display during time

display switches as follows:

Switching Display for Discs

Switch the display that appears while discs are playing.

Track time (P-TIME)

Switching Display for Discs:

Total disc playing time (A-TIME)

Each time you press the DISP button, the display during disc

play switches as follows:

Disc remaining time (R-TIME)

Playing time display

Disc name (DNPS) (Only when being preset)

Disc text (Units featuring CD text only)

Track text (Units featuring CD text only)

NOTE

• The playing time display will differ, depending on the setting of

the switching playing time display function (see page 25).

• You can give names to discs through the presetting disc names

function (see page 24).

Note that depending on the unit, display may not be possible.

— 25 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/External disc control features

NOTE

Search on Initials (Function of disc changers with remote)

• If there is only one disc with the designated initial, the operation

of step 5 will be omitted and the disc will start playing

immediately.

• You can not search a disc in the disc changer with the Search on

Initials, if you have never played the disc before.

In this case, you must play all discs by using the disc scan etc.

before using the Search on Initials.

(See page 35)

You can search a disc in the unit and the CD player/changer

with the initials of disc names or disc texts.

Press the SBF button.

"INITIAL MODE" will appear in the display, and the Search on

Initials mode is entered.

Each time the 38 button is pressed, the characters change as

listed below.

Alphabet(uppercase):A -Z 0 -9 !"# $ % & '()

＊ + , -. /:;< = > ? @ [¥ ]^「」・

Alphabet(lowercase):a -z 0 -9 !"# $ % & '()

＊ + , -. /:;< = > ? @ [¥ ]^「」・

Press the FM or AM button to select an initial character.

NOTE

If you omit the above-mentioned step 2-3, all discs will be

subjects for search.

Press the SBF button to start the search.

The disc names or disc texts, which have the designated initial,

will be displayed one after other for five seconds each.

Rapid display (forward / reverse):

Press the 4 or ¢ button.

Pressing the ¢ button will rapidly display the preset

names/disc texts in order.

Pressing the 4 button will rapidly display the preset

names/disc texts in reverse order.

When the name appears for the disc you want to play

Press the OK button.

The disc whose name is displayed will be recalled, and the

Search on Initials mode will end.

— 26 —

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3 features

DISP

DISC+

#2 #3/

RDM

DISC-

SRC

REP

Mode display

Playing time

File number

CD-ROM indicator

indicator

— 27 —

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3 features

NOTE

Playing MP3 files

• When you load a media and eject it right away, the next time

you try to insert the media may not load. In such a situation,

take the media out for a moment and then reinsert it.

• The manual search is disabled when an MP3 file is being played.

• The MP3 media that this unit can play are CD-ROM, CD-R, and

CD-RW.

The medium formats must be ISO 9660 Level 1 or Level 2. The

methods and precautions to be followed for writing MP3 files

are covered in "Notes on playing MP3 files" (page 5). Check that

section before creating your MP3 media.

• It takes time for the unit to check each medium to see if it

contains any MP3 file before it starts playing the medium.

• When the unit is playing an MP3 file, the commercially available

TV monitor VZ907 may list the currently disabled buttons on the

Audio control display.

Play:

Press the 0 button to slide open the front panel, showing the

CD (insertion) slot. Holding the media with the labeled side

facing up, insert it in the slot. The front panel will close, and the

media will start playing.

The CD-ROM indicator will light when a media has been

inserted.

The

indicator lights up when the folder containing the MP3

file currently being played has another folder at the same

hierarchical level.

Playing Media Already Inserted:

Press the SRC button repeatedly to select the CD mode.

"CD" is displayed when the CD mode has been selected.

The media will start playing.

Pausing and Restarting Media Play:

Press the 38 button to make the media pause.

Press the same button again to start play again.

NOTE

File Search

MP3-related operations (such as a file search and folder search)

cannot be performed during a pause. Cancel the pause before you

can perform such operations.

Search forward or backward through the files on the media

until you reach the one that you want to listen to.

Eject:

Making a Backward File Search:

Press the 0 button.

Press the 4 button to display the desired file number.

Press once to search back to the beginning of the current file,

twice to search back to the beginning of the previous file, and

so forth.

The front panel will slide to eject the media .

Press the 0 button to close the front panel.

2CAUTION

Play starts at the beginning of the displayed file number.

• Do not attempt to insert a media into the slot if another one is

already there.

• When the front panel has been slid open, it might interfere with

the shift lever or something else. If this happens, pay attention

to safety and move the shift lever or take an appropriate action,

then operate the unit.

• Do not apply excessive force to the front panel after it slides.

• Do not use the unit with the front panel in the slid condition.

Doing so will cause breakdown.

Making a Forward File Search:

Press the ¢ button to display the desired file number.

Press once to fast forward to the next file, twice to fast

forward to the file after that, and so forth.

Play starts at the beginning of the displayed file number.

NOTE

It may take time for the file search depending on the number of

files and the state of the folder hierarchy.

— 28 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning Folder Repeat Play On/Off:

Press the REP button at least one second to switch folder

repeat play on and off.

Folder Search

Search forward or backward through the folders on the media.

-REP" is displayed when folder repeat play is turned on.

Making a Backward Folder Search:

NOTE

^{Press the DISC}– button.

Pressing the button moves back to the previous folder. The unit

plays the medium starts at the beginning of the selected folder.

If the selected folder contains no MP3 file, the unit

automatically plays the file nearest to that folder in the MP3 file

playing order.

Folder repeat play is canceled when you eject the media.

Random Play

Play all the files on the current folder in random order.

Making a Forward Folder Search:

^{Press the DISC}+ button.

Turning Random Play On/Off:

Pressing the button moves to the next folder. The unit plays

the medium starts at the beginning of the selected folder.

If the selected folder contains no MP3 file, the unit

automatically plays the file nearest to that folder in the MP3 file

playing order.

Press the RDM button to switch random play on and off.

-RDM" is displayed when random play is turned on.

When the file has been selected, play will begin.

To change the file being heard, press the ¢ button.

Another file will be selected and played.

NOTE

It may take time for the folder search depending on the number

of files and the state of the folder hierarchy.

NOTE

Random play is canceled when you eject the media.

File Repeat

Repeat playing the file currently being listened to.

Name Scroll for MP3

This function permits the folder/file name to be scrolled and the

Turning File Repeat Play On/Off:

entire name to be displayed.

Press the REP button to switch file repeat play on and off.

You can use this function in the same manner as with audio

CDs. See "Text scroll" (page 23) for details.

-REP" is displayed when file repeat play is turned on.

NOTE

File repeat play is canceled when you eject the media.

Presetting Disc Names (DNPS)

Store the name of the media to be displayed when played.

You can name MP3 recorded media in the same way as for

audio CDs. See "Presetting Disc Names" (page 24) for details. If

you assign a disc name to a MP3 file stored disc, the same

DNPS is displayed for all discs containing MP3 data.

Folder Repeat

Repeat playing the folder currently being listened to.

— 29 —

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3 features

NOTE

Direct File Search

(Function of Remote)

(See Page 35)

• You can give names to medium through the presetting disc

name function (see p.29).

Note that depending on the unit, display may not be possible.

• If you try to display the name of a media that does not have one,

"NO NAME" is displayed instead.

• Folder names and file names are not displayed correctly if the

loaded medium does not conform to ISO 9660 Level 1/2 or if

they contain any character unacceptable to your CD writer.

• The Playing time display may not match the actual playing time

depending on the MP3 file recording states.

Using the remote, directly input the file number that you want

to listen to.

Using the number buttons on the remote, input the number of

the file that you want to listen to.

The selected file number will blink in the display for 10

seconds.

If you make no further input in the 10-second period, the

number entry mode will automatically be canceled.

Press either the 4 or ¢ button while the file number is

blinking.

The file starts playing.

Canceling Direct File Search While It Is Operating:

Folder Select

You can use this function to select the folder containing the

sound file you want be played.

Press the 38 button.

NOTE

• You cannot use the direct file search function while using

random play.

• The only files that can be selected using Direct File Search, are

those in the folder containing the MP3 file currently playing.

Enter the Folder Select Mode

Press the #2 button. “SELECT MODE” is displayed and the

folder select mode is turned on.

The display reads as shown below.

＜Foldernam e display

＞

Displaysthe currentfoldernam e.

Switching Display for MP3

Switch the display that appears while MP3 files are playing.

Switching Display for MP3:

Each time you press the DISP button, the display during files

play switches as follows.

＜

Foldernum berdisplay＞

Displaysthe num berin the folder

belonging to the currentlyselected folder.

Playing time display (Track time only)

Disc name (DNPS) (Only when being preset)

Folder name

＜

Hierarchicalleveldisplay

＞

Displaysthe hierarchicallevelofthe currentfolder.

NOTE

File name

The unit cannot enter the folder select mode if the loaded

medium contains no folder recorded.

— 30 —

Download from Www.Somanuals.com. All Manuals Search And Download.

External TV control features

Selecting the desired folder

• You can move from folder to folder at the same hierarchical

level:

FM/

AME

Press the ¢ button to move to the next folder at the same

hierarchical level.

Press the 4 button to move to the previous folder at the same

hierarchical level.

• You can select the hierarchical level of the folder:

Press the FM button to move down one level in the folder

hierarchy.

Press the AM button to move up one level in the folder

hierarchy.

• You can return to the first hierarchical level (Root Jump):

Press the #3 button to return to the folder at the top hierarchical

level on the medium currently being played.

SRC

#1 - 6

NOTE

• The

folder belongs has another folder at the same hierarchical level.

The indicator blinks when that folder contains an MP3 file.

indicator blinks when the folder to which the current

• The methods for moving to other folders in the folder select

mode are different from those in the folder search mode.

See "Notes on playing MP3 files" (page 5) for details.

Preset station number

Channel number

Band display

When you have found a desired folder

Press the 38 button.

This ends the folder select mode and starts playing the first

MP3 file in the selected folder.

NOTE

If the folder selected after leaving the folder select mode contains

no MP3 file, the unit plays the MP3 file nearest to that folder in

the MP3 file playing order.

— 31 —

Download from Www.Somanuals.com. All Manuals Search And Download.

External TV control features

NOTE

Station Preset Memory

When the TV/CD player VZ907 is connected

When the TV/CD player VZ907 is connected, the TI button

appears on the Source control screen of the TV monitor.

Since the traffic information function is not installed in this unit,

you can not use the TI button on the TV monitor.

Store the channel of a TV station. You can then recall that

station with a single touch of a button.

Select the band/station that you want to have stored.

Press the button (#1-6) that you want to use for the station, for

at least two seconds.

The button number blinks once in the display to indicate that

the data has been stored.

Tuning

NOTE

Press the SRC (source) button repeatedly to select the external

You can store six stations in each of the TV1 and TV2 bands.

TV control mode.

"TV" is displayed when the external TV control mode has been

selected.

Selecting Bands and Video Inputs

Auto Memory Entry

Press the FM button to select the TV band.

Each time you press the FM button, the TV band switches

between the TV1,TV2,Video1, and Video2.

You can automatically store all the receivable channels in the

band currently being listened to, and then recall them with the

touch of a button later. This function is especially useful when

you are travelling and do not know what stations are available.

Up to six channels can be stored this way.

• Auto Seek Tuning (AUTO 1)

Press the ¢ button to seek increasing channels.

Press the 4 button to seek decreasing channels.

• Preset Station Seek Tuning (AUTO 2)

Select the band for auto memory entry.

Press the ¢ button to move to the next preset station (the

one with the next highest number), and the 4 button to

move to the last preset station (the one with the next lowest

number).

Press the AME button for at least two seconds to start auto

memory entry.

The numbers of the preset station buttons are shown in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

• Manual Tuning (MANUAL)

Press the ¢ button to increase the channel by one step.

Press the 4 button to decrease the channel by one step.

NOTE

You can select the Tuning mode of AUTO1, AUTO2, or MANUAL

at the television side. For details, please refer to the instruction

manual for the television.

Preset Tuning

You can recall a station being preset in preset station buttons

(#1-6).

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

— 32 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Function set system

Direct Access Tuning

(Function of Remote)

(See page 35)

Use the remote to select channels directly.

AUD

Select the TV band by pressing the FM button.

Press the DIRECT button.

In the display, "--" blinks for 10 seconds.

If you make no input in the 10-second period, direct access

tuning is automatically canceled.

Enter the channel of the desired station while the display is

blinking.

If you want to watch the channel 21 of the TV station, for

example, press 2 and 1.

SRC

NOTE

You cannot enter channnels above or below what a band can

receive.

Canceling Direct Access Tuning:

Press the DIRECT button again.

Setting display

— 33 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Function set system

Function Set System

Touch Sensor Tone

This function produces a beep sound that accompanies button

operation. It can be switched on or off.

To accommodate a greater number of functions, a function set

system has been employed for making settings. Press the AUD

button to enter the function set mode and then display the

function to make the setting.

Display and setting:

"BEEP ON" : Beep setting is on.

"BEEP OFF" : Beep setting is off.

Press the SRC button repeatedly and switch the display to

“ALL OFF” to enter the standby mode.

NOTE

Press the AUD button.

The beep sound is not output from the preout jacks.

"FUNCTION SET" is displayed when the function set mode is

entered.

The function that you can adjust is indicated with the current

settings displayed.

Dimmer

You can dim the display.

Selecting function to set

Press the FM button to search through the functions until you

see the one you want to adjust in the display.

Display and setting:

Press the AM button to search through the functions backward.

Example: If you want to switch the setting of the touch sensor

tone function from on to off, first search through the

functions until you see "BEEP ON"in the display.

"DIMMER LOW" : The dimmer setting is low.

"DIMMER MIDDLE" : The dimmer setting is middle.

"DIMMER HIGH" : The dimmer setting is high.

NOTE

The dimmer function is not available for units if the dimmer wire

is not connected.

Changing setting for currently displayed function

Press either the 4 or ¢ button.

The setting will change for each function.

Example: The setting of the touch sensor tone will switch from

on to off, and "BEEP OFF" is displayed.

Silent Display

If you feel that display amount on the screen is too much, you

can reduce the display amount.

Display and setting:

Ending the function set mode

Press the AUD button.

"SILENT ON" : The silent display function setting is on.

"SILENT OFF" : The silent display function setting is off.

— 34 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations of remote

KEX (Sound Coordinate system)

When this system is set to on, the sound coordinate factors

(KEX.P, Bass Frequency, Bass quality, Bass extension, and

Treble frequency) appear during the audio control mode.

Display and setting:

"KEX CTRL ON" : The sound coordinate factors appear and can

be adjusted.

"KEX CTRL OFF" : The sound coordinate factors are not

appeared.

SRC

TUNE -/4/TRACK -

^TUNE+/¢/TRACK +

^FM/DISC+

ATT

^AM/DISC-

SP (Speaker selector)

Using this function to set the diameter of the speaker optimizes

the sound quality to the speaker diameter.

SBF

DIRECT/OK

#0-9/A-Z

Display and setting:

"STANDARD": Speaker with a general diameter

"NARROW": Speaker with small diameter

"WIDE":

Woofer with a large diameter

"MIDDLE": Tweeter with a small diameter

NOTE

• This mode is available only when the Sound coordinate system

is on. (page 35)

• This function fine-tunes the settings for bass center frequency,

bass level, bass quality factor, bass extension, treble center

frequency, and treble level which are recalled by Sound preset

under Audio control.

— 35 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations of remote

2CAUTION

General features

Do not set the remote on hot places such as above the

dashboard.

• VOLUME buttons

^{Press the}+ button to turn the volume up.

Loading and Replacing the Batteries:

Use two “AAA”-size batteries.

Press the – button to turn the volume down.

• SRC button

Slide the cover while pressing downwards to remove it as

illustrated.

Each time you press the SRC button, the mode switches as

follows:

^{Insert the batteries with the}+ and – ^{poles aligned properly,}

following the illustration inside the case.

Tuner mode

CD/MP3 mode

External disc control modeMM

External TV control modeMM

Standby modeMM

NOTE

2WARNING

• The mode switches to the next mode from any mode which

cannot be used.

Store unused batteries out of the reach of children. Contact a

doctor immediately if the battery is accidentally swallowed.

NOTE

• The external disc and TV control mode will differ depending on

the unit that is connected.

• The provided batteries are intended for use in operation

checking, and their service life may be short.

• When the remote controllable distance becomes short, replace

both of the batteries with new ones.

• A portion of the operations may not be possible, depending on

the unit that is connected.

• MP3 files can be played only on this unit.

• ATT button

Turns down the volume quickly. To return the volume to its

original level, press the button again. Turning the volume up, or

turning it all the way down deactivates the attenuator function.

•

button

Each time you press this button, the front panel slides one step

at a time.

When the front panel has been slid down completely, press this

button to close the front panel.

— 36 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

CD/External disc/MP3 control features

• Number/letter entry buttons

Press buttons #1-6 to recall preset stations.

During direct access tuning, use these buttons to input the

frequency of the station.

Use to enter letters during the Search on Initials.

Used to specify the track (disc/file) number used in direct track

(disc/file) searches.

Use to enter letters (alphabetical) during station name preset.

Select a disc directly by inputting a disc number with this button

during the Direct Disc Search mode.

NOTE

• 4/¢ (TUNE) buttons

Press the 4 button to decrease the frequency.

Press the ¢ button to increase the frequency.

Use to move the cursor left or right during station name input.

Input "0" to select disc 10.

• 4/¢ buttons

• AM/FM button

Press the 4 button to search through the tracks and files

backward.

Press the AM button to select the AM band.

Press the FM button to select and switch between FM1, FM2,

and FM3 bands.

Press the ¢ button to search through the tracks and files

forward.

During station name input, selects digits and symbols.

Use to move the cursor while entering disc name.

• DIRECT/OK button

• DISC buttons (For disc changers and media containing MP3 files)

^{Press the DISC}– button to search through the discs and folders

backward.

Selects the direct access tuning mode, used to input frequencies

directly. Press this button again to cancel the mode while it is

operating.

^{Press the DISC}+ button to search through the discs and folders

During station name input, stores the already input data in

memory and ends the input mode.

During Station Name Preset Play mode, selects station.

forward.

Select numbers and symbols while entering disc name.

• 38 button

• SBF button

When a disc is playing, this button pauses the play.

Press the same button again to start play again.

Selects the type of characters at the time of entering the disc

name.

Enters the Station Name Preset Play mode.

During Station Name Preset Play mode, selects station.

• 38 button

Selects the type of characters at the time of entering the station

name.

• DIRECT/OK button

Press this button to select the Direct Disc Search mode.

Selects disc during the Search on Initials mode.

During disc name input, stores the already input data in memory

and ends the input mode.

• SBF button (for disc changers)

Enters the Search on Initials mode.

Selects disc during the Search on Initials mode.

— 37 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations of remote

External TV control features

• Number/letter entry buttons

Press buttons #1-6 to recall preset channels.

During direct access tuning, use these buttons to input the

channel of the station.

• 4/¢ (TUNE) buttons

Press the 4 button to make decreasing seeks.

Press the ¢ button to make increasing seeks.

• FM button

Each time you press the FM button, the TV band switches

between the TV1,TV2,Video1, and Video2.

• DIRECT button

Selects the direct access tuning mode, used to input a channel

directly. Press this button again to cancel the mode while it is

operating.

— 38 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Installation Procedure

1. To prevent a short circuit, remove the key from the ignition and

External view

.....Number of items

disconnect the - battery.

.....Number of items

2. Make the proper input and output wire connections for each unit.

3. Connect the speaker wires of the wiring harness.

4. Connect the wiring harness wires in the following order: ground,

battery, ignition.

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

........1

2CAUTION

15mm

20mm

• If your car's ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on and

off with the ignition key. If you connect the ignition wire to a

power source with a constant voltage supply, as with battery

wires, the battery may die.

• If the console has a lid, make sure to install the unit so that the

faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching to

cause a short circuit, then replace the old fuse with one with

the same rating.

• Do not let unconnected wires or terminals touch metal on the

car or anything else conducting electricity. To prevent a short

circuit, do not remove the caps on the ends of the unconnected

wires or the terminals.

........1

........2

........4

........2

• Connect the speaker wires correctly to the terminals to which

they correspond. The unit may be damaged or fail to work if you

share the - wires or ground them to any metal part in the car.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Insulate unconnected wires with vinyl tape or other similar

material.

• Mount the unit so that the mounting angle is 30° or less.

2CAUTION

The use of any accessories except for those provided might

result in damage to the unit. Make sure only to use the

accessories shipped with the unit, as shown above.

— 39 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Wires to Terminals

2WARNING

If you connect the ignition wire (red) and the battery

wire (yellow) to the car chassis (ground), you may

cause a short circuit, that in turn may start a fire.

Always connect those wires to the power source

running through the fuse box.

FM/AM antenna input

Front right output (Red)

Front left output (White)

2CAUTION

Rear right output (Red)

Rear left output (White)

When only two speakers are being connected to

the system, connect the connectors either to both

the front output terminals or to both the rear output

terminals (do not mix front and rear). For example, if

you connect the + connector of the left speaker to

a front output terminal, do not connect the -

connector to a rear output terminal.

BUS terminals

Non-fading right output (Red)

Non-fading left output (White)

Fuse (10A)

If no connections are made, do not let the wire come out from the tab.

Z919

When using the optional power amplifier,

Wiring harness

connect to its power control terminal.

P.CONT

Power control wire

(Accessory1)

(Blue/White)

Depending on what antenna you are using, connect

either to the control terminal of the motor antenna, or

to the power terminal for the booster amplifier of the

film-type antenna.

ANT

CONT

Motor antenna control wire

(Blue)

White/Black

To front

left speaker

FRONT

To car light control switch

ILLUMI

Dimmer control wire

(Orange)

White

Gray/Black

To "EXT.AMP.CONT." terminal of the amplifier

having the external amp control function.

EXT.CONT.

External amplifier control

wire

To front

right speaker

FRONT

(Pink / Black)

Ignition key

switch

ACC

Gray

Green/Black

Ignition wire (Red)

Car fuse box

To rear

left speaker

Car fuse

REAR

box

Battery wire (Yellow)

Green

Purple/Black

(Main

fuse)

To rear

right speaker

Ground wire (Black) - (To car chassis)

REAR

Purple

Battery

— 40 —

Download from Www.Somanuals.com. All Manuals Search And Download.

System Connection

Changer control cable

(Provided with C907)

NOTE

• Do not remove the protection caps of the

unused BUS terminals.

• Put the protection caps removed from the unit

into the unused terminals in the unit

connected.

Protection cap

— 41 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Assembly

NOTE

How to install the rubber bushes (Accessories8 and 9)

When installing, adjust the rubber bushes so that the position of

the main unit is aligned with the position of the radio.

Accessory2

Accessory 2

Cut off the end

using a cutter.

Accessory 4

Fit the projections on both

sides of the Accessories 4

into the slits on the

Accessory2.

Accessory 6

Accessory 7

(Used when there

are rubber bushes on

the rear panel of the

radio.)

Accessory5

(M5 × 6 mm)

Installation example

NOTE

Assemble the stepped screw (Accessory6), the joint nut

(Accessory7), the rubber bushes (Accessories8 and 9), and

secure them to the rear panel of the unit.

Accessories5 should be screwed in firmly.

If it is not properly secured, it may rub against

the mounting sleeve when the unit is removed,

making itself impossible to remove.

Accessory 6

2CAUTION

• Be sure to press the reset button after installation.

• During installation, do not use any screws except for those

provided. The use of different screws might result in damage

to the main unit.

• Damage may occur if a screwdriver or similar tool is used

with excessive force during the installations.

• When performing a check of the CD operation prior to

installation, place this unit in a hirizontal position and perform

a loading/eject of the CD.

Accessory 9

Accessory 8

Accessory 7

NOTE

• This installation method is a reference example.

• Make sure that the unit is installed securely in place. If the

unit is unstable, it may malfunction (for example, the sound

may skip).

— 42 —

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE

Installation

In the case of an Audi, a Volkswagen, or any other model where

rubber bushes (Accessories 8 and 9) are used, install the unit

so that the rubber bushes on the rear panel fit into the holes on

the car side.

Remove the factory-installed car stereo and install the unit that

was assembled in Assembly.

Install the mounting sleeve (Accessory3) on the car side with

the face labeled "UP" facing upwards.

Accessory89

Hole

Press in as far as this position.

Bend the tabs of the mounting sleeve(Accessory3) with a

screwdriver or similar utensil and attach it in place.

Installing in Japanese-Made Cars

Align the holes in the unit (two locations on each side) with the

vehicle mounting bracket and secure the unit with the

accessory screws.

Connect the wires from the car side, and then insert the

assembled unit into the mounting sleeve.

Accessory!

(M5X6mm)

Z919

Antenna

cable

— 43 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Removing the Unit

Screw the removal screws (Accessory0) away from you until

the lock is released.

Accessory0

Pull the unit all the way out with your hands, being careful

not to drop it.

— 44 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before

calling service, first check the following table for possible problems.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the wires, replace the

fuse with one with the same rating.

No sound can be heard, or the

volume is low.

Attenuator is turned on.

Turn off Attenuator.

The fader or balance settings are set all the way to one

side.

Reset the fader or balance settings.

The input/output wires or wiring harness are connected

incorrectly.

Reconnect the input/output wires or the wiring harness

correctly. See the section on "Connecting Wires to

Terminals".

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

Press the reset button on the unit (see p.4).

One of the speaker wires is being pinched by a screw in

the car.

Check the speaker wiring.

The sound quality is poor or

distorted.

The speakers are not wired correctly.

Reconnect the speaker wires so that each output terminal is

connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull the antenna out all the way.

The antenna control wire is not connected.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

The memory is erased when

the ignition is turned off.

The battery wire has not been connected to the proper

terminal.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

The ignition and battery wire are incorrectly connected.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

A CD ejects as soon as it is

loaded.

The CD is upside-down.

The CD is quite dirty.

Load the CD with the labeled side up.

Clean the CD, referring to the section on "Cleaning CDs" (see

p.8).

The sound skips on a CD.

The CD is scratched or dirty.

Clean the CD, referring to the section on "Cleaning CDs" (see

p.8).

A track will not play.

Random play has been selected.

The CD is soiled with dust or dirt.

Turn off random play.

There is noise during playback.

If another CD is played back and there is no problem, then

the problem is due to the sound quality of the CD itself.

— 45 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

PROBLEM

POSSIBLE CAUSE

SOLUTION

The sound skips.

The mounting angle exceeds 30°.

Adjust to an angle of less than 30°.

The mounting is unstable.

Anchor the unit securely. When the sound skips at the same

portion even when the car is stopped, the problem lies with

the CD.

Cannot play an MP3 file.

Not conforming to ISO 9660 Level 1/2.

The MP3 file has no or invalid filename extension.

The media is scratched or dirty.

Use a medium conforming to ISO 9660 Level 1/2.

Add the ".MP3" extension to the MP3 file name.

Clean the media, referring to the section on "Cleaning CDs"

(see p.8).

Noise or no sound generated

when an MP3 file is played.

The file has the MP3 filename extension while it is not an

MP3 file.

Do not use the ".MP3" extension in non-MP3 files.

Takes time before the unit

starts playing MP3 files.

The medium contains many folders, files, and hierarchical

levels.

The unit checks all files on the loaded medium first. If the

medium has many files recorded, it may take a long time for

the unit before it starts playing MP3 files.

Fails to play MP3 files in the

intended order.

The MP3 files were not written by the CD writer in the

order in which you wanted them to be played.

Depending on the CD writer, you may be able to set the

order in which MP3 files are to be played by writing them

onto a medium with their file names beginning with play

sequence numbers such as "01" to "99".

The sound skips when an MP3

file is being played.

The media is scratched or dirty.

Clean the media, referring to the section on "Cleaning CDs"

(see p.8).

The following messages are displayed when certain problems are occurring in your system. Take the recommended

actions.

No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.

] Load the disc magazine properly.

EJECT

No disc has been loaded in the disc magazine.

] Load a disc into the disc magazine.

NO DISC

— 46 —

Download from Www.Somanuals.com. All Manuals Search And Download.

•An attempt was made to display the name of the station being received but it was not set in memory.

•An attempt was made to display the name of the disc being played but it was not set in memory.

NO NAME

An attempt was made to display the track/disc title of the CD during play, but the CD has no texts.

NO TEXT

No disc has been loaded in the disc magazine.

] Load a disc into the disc magazine.

ERROR 04

The CD is quite dirty. The CD is upside-down. The CD is scratched a lot.

] Clean the CD and load it correctly.

The unit is malfunctioning for some reason.

ERROR 77

ERROR 99

] Press the reset button on the unit. If the "ERROR 77" code does not disappear, consult your nearest service center.

Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.

] Check the disc magazine. And then press the reset button on the unit. If the "ERROR 99" code does not disappear, consult

your nearest service center.

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),

HOLD

stopping all operation.

] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the

disc will start playing again.

The protective circuit in the unit activates when the temperature inside the unit exceeds 60°C (140°F), stopping all operation.

] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the

disc will start playing again.

H HOLD

The CD player is malfunctioning.

] Eject the CD and try inserting it again.

Contact the Kenwood dealer if this indicator continues blinking or the CD cannot be ejected.

More than two center units are connected.

BUS-E50

BUS-W02

The number switches of two disc changers connected are set to the same number.

] You can use without any problem, by setting a switch number of one disc changer to "1" and another to "2".

More than two TV monitors are connected at the BUS.

BUS-W08

READING

The unit is reading the data on the disc.

] Normal play will be performed after completion of reading the data on the disc.

The unit is replaying the data area on the CD-ROM.

] You can not hear sound during this indication appears.

CD-ROM AREA

The unit failed to read the MP3 folder name and file name.

Cannot display format

— 47 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Specifications subject to change without notice.

FM tuner section

Audio section

Frequency range (200 kHz space) .............87.9 MHz – 107.9 MHz

Usable sensitivity (S/N = 30dB).....................9.3dBf (0.8 µV/75 Ω)

Quieting Sensitivity (S/N = 50dB)................15.2dBf (1.6 µV/75 Ω)

Frequency response ( 3.0 dB) ..............................30 Hz – 15 kHz

Signal to Noise ratio (MONO) ..............................................75 dB

Selectivity ( 400 kHz).......................................................≥ 80 dB

Stereo separation (1 kHz).....................................................40 dB

Maximum output power .................................................45 W × 4

Full bandwidth power (at less than 1% THD)..................22 W × 4

Tone action

Bass: ...........................................................100 Hz 10 dB

Treble: .........................................................10 kHz 10 dB

Preout level / Load ...............................................1500 mV/10 kΩ

Preout impedance ...........................................................≤ 600 Ω

AM tuner section

General

Frequency range (10 kHz space)....................530 kHz – 1700 kHz

Usable sensitivity (S/N = 20dB) .............................28 dBµ (25 µV)

Operating voltage..............................14.4 V (11 – 16 V allowable)

Current consumption.............................................................10 A

Installation size (W × H × D) ...........................178 × 50 × 160 mm

(7 × 1-15/16 × 6-5/16 in.)

CD player section

Laser diode ....................................................GaAlAs (λ=780 nm)

Digital filter (D/A)......................................8 Times Over Sampling

D/A Converter ...............................................................8 level ∆Σ

Spindle speed...............................................200 – 500 rpm (CLV)

Wow & Flutter........................................Below Measurable Limit

Frequency response ( 1 dB) .................................10 Hz – 20 kHz

Total harmonic distortion (1 kHz) ......................................0.01 %

Signal to Noise ratio.................................................96 dB (1 kHz)

Dynamic range ....................................................................95 dB

Channel separation..............................................................90 dB

MP3 decoder ........................MPEG-1.0 Audio Layer-3 compliant

Weight ................................................................................1.6 kg

(3.5 Lbs)

— 48 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Indesit Freezer B 339 NF P User Manual
Invacare Mobility Aid 1110266 User Manual
IOGear Mouse 1600DPI User Manual
Jasco Satellite TV System TV24713 User Manual
Jet Tools Dust Collector DC 1200C User Manual
JVC Camcorder GR AX270 User Manual
JVC Speaker System TH D7 User Manual
JVC Stereo System 0409WMKMDWJMM User Manual
Kambrook Fan KFH500 User Manual
Kamera Werk Dresden Digital Camera PRO 150 User Manual