CD-RECEIVER
KDC-X991
INSTRUCTION MANUAL
HD
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the
warranty card, and in the space provided below. Refer to the model and serial numbers
whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-X991 Serial number
US Residence Only
Register Online
Register your Kenwood product at
© B64-3767-00/00 (KW)
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
• Use only the screws provided or specified for
installation. If you use wrong screws, you could
damage the unit.
2 WARNING
To prevent injury while using this
product, take the following safety
precautions:
Attach the panel while you are on the
vehicle
• To prevent a short circuit and possible fire, never
put any metallic objects (such as coins or metal
tools) inside the product.
The panel lock arm appears when the panel is
removed. Therefore, the panel must be attached while
the electrical system of the car is operating.
• If you are the driver and your vehicle is moving,
do not watch the product’s display or use its
controls for an extended period.
• Do not use this product in any way that prevents
you from driving safely.
Do Not Load 3-in. CDs in the CD slot
If you try to load a 3 in. CD with its adapter into the
unit, the adapter might separate from the CD and
damage the unit.
• Follow all driving laws and use common sense
when using this product.
About CD players/disc changers connected
to this unit
NOTE:
• Like your vehicle’s speedometer, G-Analyzer is
no more than a measuring function. The HP
or G value measured by this unit may not be
completely accurate due to its simplified method of
measurement. The G-Analyzer is only for reference
and should not be used to confirm the horsepower
specifications of your vehicle.
Kenwood disc changers/ CD players released in 1998
or later can be connected to this unit.
Refer to the catalog or consult your Kenwood dealer
for connectable models of disc changers/ CD players.
Note that any Kenwood disc changers/ CD players
released in 1997 or earlier and disc changers made by
other makers cannot be connected to this unit.
Connecting unsupported disc changers/CD players to
this unit may result in damage.
Set the "O-N" Switch to the "N" position for the
applicable Kenwood disc changers/ CD players.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting
and wiring work to professionals.
2CAUTION
To prevent damage to the machine, take
the following precautions:
¤
• Make sure to ground the unit to a negative 12V DC
power supply.
•
You can damage both your unit and the CD changer if you
connect them incorrectly.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not place the faceplate (and the faceplate case)
in areas exposed to direct sunlight, excessive heat or
humidity. Also avoid places with too much dust or
the possibility of water splashing.
• To prevent deterioration, do not touch the terminals
of the unit or faceplate with your fingers.
• Do not subject the faceplate to excessive shock, as it
is a piece of precision equipment.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
• When replacing a fuse, only use a new fuse with
the prescribed rating. Using a fuse with the wrong
rating may cause your unit to malfunction.
• Do not apply excessive force to the open faceplate
or place objects on it. Doing so will cause damage
or breakdown.
English
|
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• We recommend the use of <Activating Security
Code> (page 45) to prevent theft.
• The characters conforming to ISO 8859-1 character
set can be displayed.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
• The RDS feature won’t work where the service is not
supported by any broadcasting station.
• In this document, the description indicator will light
means a status is displayed. Refer to <Display Type
Selection> (page 16) for the details of the status
display.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe
them with a clean soft dry cloth.
• The illustrations of the display, the function icon and
the panel appearing in this manual are examples
used to explain more clearly how the controls are
used. Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
<Demonstration mode Setting> (page 53).
About KENWOOD "Music Editor" of PC
application attached to KDC-X991
• "Music Editor" is recorded in the CD-ROM attached
to this unit.
• Refer to the attached installation manual for the
installation method of "Music Editor".
• Refer to the user’s manual recorded in the
installation CD-ROM and Help of "Music Editor" for
the operation method of "Music Editor".
• The unit can play CD/ USB device created by "Music
Editor".
How to reset your unit
• If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when the
Reset button is pressed.
• Remove the USB device before pressing the Reset
button. Pressing the Reset button with the USB
device installed can damage the data contained in
the USB device. For how to remove the USB device,
refer to <Playing USB (iPod) device> (page 31).
• Stop recording and copying before pressing the
reset button. If the reset button is pressed while
writing to the internal memory such as when
recording or copying, the data in the internal
memory may be damaged. Refer to <Recording
music CD> (page 36) and <Copying from USB
device> (page 38) for information on canceling
recording or copying.
• Information about "Music Editor" upgrade is put on
• Press the reset button if the disc auto changer fails
to operate correctly. Normal operation should be
restored.
Reset button
|
4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
About Audio file
About USB device
•
Playable Audio file
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma),
WAV (.wav)
• You cannot connect a USB device via a USB hub.
•
•
•
•
Playable disc media
CD-R/RW/ROM
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
• For how to play the audio files recorded in a USB
device, see <CD/Audio file (USB/iPod/Internal
Memory) control features> (page 30).
• When connecting the USB device, usage of the CA-
U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Playable USB device
USB mass storage class, iPod with KCA-iP200
Playable USB device file system
FAT16, FAT32
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
<
v
:
:
Follder
Audiofile
CD
(ꢂ)
About ODD (Offset Dual Differential) D/A
System
vꢀ
ꢁ
The high quality sound play is to be done by ODD
D/A System. Dual D/A converters are built-in the ODD
D/A System, and the digital processing is isolated and
controlled separately for front channel so the channel
separation is improved sharply.
ꢃ
vꢆ
vꢇ
ꢅ
vꢄ
ꢈ
vꢉ
v.
Also, the ODD D/A System produces the data by
which the sound data is offset on the minus side and
converts the two signals (original and offset data) to
the analog signal, which has less noise and distortion,
by the synthetic process.
However, ODD D/A System will be disabled if the
following settings are selected.
An online manual about audio files is put on the
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
- When "2 ZONE" of <Audio Setup> (page 10) is "ON".
⁄
•
In this manual, the word "USB device" is used for flash
memories and digital audio players which have USB
terminals.
•
The word "iPod" appearing in this manual indicates the iPod
connected with the KCA-iP200 (optional accessory). The
iPod connected with the KCA-iP200 can be controlled from
this unit. iPods that can be connected with the KCA-iP200
are the iPod nano and the iPod with video. When an iPod
is connected using a commercially available USB cable, it is
handled as a mass-storage-class device.
•
For the supported formats and types of USB device, refer to
English
|
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
About Bluetooth Hands free control
Refer to the instruction manual of the Bluetooth
Hands Free Box KCA-BT100 (optional accessory).
However, the following control methods of the
function for this unit may be different from the
Instruction manual; therefore, refer to the following
supplemental instruction.
<Dialing by Using the Quick Dialing Function>
1. Press the Control knob. Select the "DIAL" display.
2. Press the [FNC] button.
3. Select the number to recall by turning the Control
knob.
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
4. Press the Control knob.
<Registering to the Preset Dial Number List>
1. Operation is the same. Refer to the instruction
manual of KCA-BT100.
CDs that cannot be used
• CDs that are not round cannot be used.
2. Press the [FNC] button.
3. Select the number to memory by turning the
Control knob.
4. Press the Control knob for at least 1 second.
<Deleting a Registered Cell-Phone>
1–3. Operation is the same. Refer to the instruction
manual of KCA-BT100.
4. Press the Control knob.
5. Select "YES" using the Control knob.
6. Press the Control knob.
7. Press the [FNC] button.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not been
finalized. (For the finalization process refer to your
CD-R/CD-RW writing software, and your CD-R/CD-
RW recorder instruction manual.)
About Menu operation
For how to operate Menu, refer to <Menu System>
in this instruction manual. For the items to be set
up, refer to the instruction of Hands Free Box.
About display of Cell-Phone Status
Cell-Phone Status is displayed in the status display
of this unit. For the information about the displayed
icons, refer to the instruction manual of Hands
Free Box. Bluetooth connection status cannot be
displayed.
|
6
English
Download from Www.Somanuals.com. All Manuals Search And Download.
2CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
In compliance with Federal Regulations, following
are reproductions of labels on, or inside the product
relating to laser product safety.
Kenwood Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER 1, SUBCHAPTER J.
Location : Bottom Panel
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless
the modifications are expressly approved in the
instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change
or modification is made.
NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment may cause harmful interference to radio
communications, if it is not installed and used in
accordance with the instructions. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
WOW HD, SRS and
symbol are
trademarks of SRS Labs, Inc.
WOW HD technology is incorporated under
license from SRS Labs, Inc.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
iPod is a trademark of Apple, Inc., registered in
the U.S. and other countries.
The "AAC" logo is trademark of Dolby
Laboratories.
• Consult the dealer or an experienced radio/TV
technician for help.
English
|
7
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
ATT
VOL
ꢀ
Control knob
Release button
FNC
SRC
ATT indicator
Function icon
Power
Source required
Display
"SAT"
Satellite radio (Optional accessory)
Tuner or HD Radio (Optional accessory)
USB device (iPod)
Internal Memory
CD
Turning ON the Power
Press the [SRC] button.
"TUNER" or "HD Radio"
"USB" ("iPod")
"Internal Memory"
"Compact Disc"
"CD Changer"
"AUX"
Turning OFF the Power
Press the [SRC] button for at least 1 second.
External disc (Optional accessory)
Auxiliary input
Auxiliary input (Optional accessory)
Standby (Illumination only mode)
"AUX EXT"
"STANDBY"
Selecting the Source
There are two types of source selection methods
depending on the setting.
⁄
•
When connection of the iPod is recognized, the source
display changes from "USB" to "iPod".
SRC Select mode 1:
•
•
Switch between SRC Select mode 1 and 2 in <Source
Select mode> (page 46).
USB (iPod) or Internal Memory source is recognized as
CD source on the connected unit.
1 Press the [SRC] button.
2 Turn the Control knob or push it towards left or
right.
3 Press the Control knob.
SRC Select mode 2:
Press the [SRC] button.
|
8
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume
Audio Control
Increasing Volume
Turn the [VOL] knob clockwise.
1 Select the source to adjust
Press the [SRC] button.
Refer to <Selecting the Source> (page 8).
Decreasing Volume
Turn the [VOL] knob counterclockwise.
2 Enter Audio Control mode
Press the [VOL] knob.
3 Select the Audio item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
Attenuator
Turning the volume down quickly.
Press the [ATT] button.
Each time you press the button, the Attenuator
turns ON and OFF.
When the Attenuator is ON, the "ATT" indicator
blinks.
4 Adjust the Audio item
Turn the [VOL] knob.
Adjustment Item Display
Range
0 — 35
Rear Volume
Subwoofer level
Balance
"REAR VOLUME"
"SUBWOOFER LEVEL" –15 — +15
"BALANCE"
"FADER"
Left 15 — Right 15
Rear 15 — Front 15
Fader
Loudness
Compensating for low and high tones during low
volume. (Only the low tone is compensated for
when the tuner is selected as a source.)
Exit Audio Control mode (Volume control mode)
5 Exit Audio Control mode
Press any button.
Press a button other than the [VOL] knob, [0] and
[ATT] button.
1 Enter Loudness mode
Using the Control knob, select "DSP" > "SND
CONT" > "LOUD".
For the operation method, refer to <Function
Control mode> (page 11).
2 Select the Loudness
Turn the Control knob.
Each time you push the knob, the Loudness turns
ON and OFF.
3 Exit Loudness mode
Press the Control knob.
English
|
9
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Audio Setup
Subwoofer Output
Setting the Sound system, such as Volume offset
and Dual Zone.
Turning the Subwoofer output ON or OFF.
Push the Control knob toward down for at least
2 seconds.
Each time you push the knob, Subwoofer output
switches ON and OFF.
When it is ON, "SUBWOOFER ON" is displayed.
1 Select the source to adjust
Press the [SRC] button.
Refer to <Selecting the Source> (page 8).
2 Enter Audio Setup mode
Press the [VOL] knob for at least 1 second.
3 Select the Audio Setup item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
In Audio file source
Supreme Setting
When AAC, MP3 or WMA files encoded at a low
bit rate (less than 128kbps (fs=44.1k, 48kHz)) are
played, this function restores their high frequency
region to approach the sound quality of equivalents
of these files encoded at a high bit rate. Processing
is optimized for the compression format used (AAC,
MP3, or WMA), and adjustment is made for the bit
rate used.
4 Setup the Audio item
Turn the [VOL] knob.
Adjustment Item Display
Range
"VOLUME OFFSET" –8 — 0 (AUX: -8— +8)
"2 ZONE" ON/OFF
Volume offset
Dual Zone System
⁄
1 Enter Supreme Setting mode
Using the Control knob, select "DSP" > "SND
CONT" > "Supreme".
For the operation method, refer to <Function
Control mode> (page 11).
•
Volume offset: Sets each source’s volume as a difference
from the basic volume.
Dual Zone System
•
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
- Set up the channel of sub source by <Dual Zone
System Setting> (page 48).
2 Select the Supreme
Turn the Control knob or push it towards left
or right.
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by [VOL] knob.
- Adjust the volume of Rear channel by <Audio Control>
(page 9).
Display
Setting
"Supreme ON"
Plays sound using the Supreme function.
- The DSP Control will be disabled.
"Supreme OFF"
Plays the original sound stored in the audio file.
•
You can use the Dual Zone System only when you have
set the rear speaker to any mode other than "None" in
the <Sound Management system> (page 12).
3 Exit Supreme Setting mode
Press the Control knob.
5 Exit Audio Setup mode
⁄
•
Press the [VOL] knob for at least 1 second.
The sound effect may be imperceptible depending
on the relationship between the audio file format and
setting.
•
This function is not available on iPod.
|
10
English
Download from Www.Somanuals.com. All Manuals Search And Download.
TEL Mute
Function Control mode
The audio system automatically mutes when a call
comes in.
To set up various functions of this unit, select tree-
structured function items.
When a call comes in
"CALL" is displayed.
1 Enter Function Control mode
Press the [FNC] button.
The audio system pauses.
2 Select your desired setup item
Listening to the audio during a call
Press the [SRC] button.
The "CALL" display disappears and the audio system
Select a setup item using the Control knob.
Operation type
Operation
Movement between items Turn the Control knob.
comes back ON.
Selection of item
Return to previous item
Press the Control knob.
Press the [FNC] button.
When the call ends
Hang up the phone.
The "CALL" display disappears and the audio system
Functions of items are as follows:
comes back ON.
Display
Icon
Function of setup item
"Menu"
"MENU"
Allows you to set up the environment.
Refer to <Menu system> (page 44).
Sets the DSP function. Refer to page 12
to page 16.
⁄
•
To use the TEL Mute feature, you need to hook up
the MUTE wire to your telephone using a commercial
telephone accessory. Refer to <Connecting Wires to
Terminals> (page 57).
"DSP"
"DSP"
"Display Select" "DISPLAY" Allows you to set up the display. Refer
to page 16 to page 23.
"Angle Adjust" "ANGLE"
Allows you to set the panel angle. Refer
to <Angle Control> (page 24).
"Preset Memory" "P.MEMORY" Allows you to put stations in the
memory. Refer to <Station Preset
Memory> (page 27).
"File Scan" etc. "SCAN" etc. Allows you to set how to play the CD
and audio file. Refer to <Play function
of CD and Audio file> (page 33).
"Return"
Returns to the previous item.
"
"
3 Select an option for the selected item
Refer to the related pages for the operation of
each option.
4 Exit Function Control mode
Press the [FNC] button for at least 1 second.
English
|
11
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
1 Set reference point so that the front/rear positions and
height are at the position of the ears of the person
sitting in the front seat and the left/right position is at
the center of the cabin.
2 Measure the distance from the reference point to the
speaker.
3 Calculate the difference in distance with reference to
the farthest speaker.
"X'OVER" (Crossover Network Setup)
You can manually set a crossover frequency for the
speakers.
Sound Management system
1 Enter Sound Management mode
Using the Control knob, select "DSP" > "S.M.S".
For the operation method, refer to <Function
Control mode> (page 11).
2 Select the Sound Management item to adjust
Turn the Control knob or push it towards left
or right.
•
Press the Control knob.
3 Adjust the Sound Management item
Turn the Control knob or push it towards left
or right.
Each time you push the knob, the setting alternates
between the settings shown in the table below.
Icon
"CABIN"
Sound Management Item
Cabin Setting
"SPEAKER">"FRONT" >"LOCATION" Speaker Location Front
>"SIZE"
Speaker Size Front
>"TWEETER" Speaker Select Tweeter
>"REAR" >"LOCATION" Speaker Location Rear
"CABIN"
>"SIZE"
Speaker Size Rear
Sound Management Item Range
Cabin Setting
>"SUB-W" >"SIZE"
Speaker Size Subwoofer
OFF/ Compact/ Full Size Car/ Wagon/
Minivan/ SUV/ Minivan(Long)
"DTA"
>"FRONT"
>"REAR"
>"SUB-W"
DTA Front
DTA Rear
DTA Subwoofer
"SPEAKER"
"X'OVER"* >"FRONT"
>"REAR"
Front High Pass Filter
Rear High Pass Filter
Subwoofer Low Pass Filter
Sound Management Item Range
Speaker Location Front
Speaker Size Front
>"SUB-W"
Door/ On Dash/ Under Dash
6½/ 6¾/ 7/ 4×6/ 5×7/ 6×8/ 6×9/
7×10/ O.E.M./ 4/ 5 (inch)
* The following adjustment items can be selected by up or
down knob for "X'OVER".
Speaker Size Tweeter
Speaker Location Rear
None/ Use
• Door/ Rear Deck
• 2nd Row/ 3rd Row (Minivan/
Minivan(Long))
6½/ 6¾/ 7/ 4×6/ 5×7/ 6×8/ 6×9/
7×10/ None/ O.E.M./ 4/ 5 (inch)
Icon
>"FRONT" "fc"
"Slope"
>"REAR" "fc"
"Slope"
>"SUB-W" "fc"
"Slope"
"Phase"
Display
Sound Management Item
Front High Pass Filter Cut off Frequency
Front High Pass Filter Slope
Rear High Pass Filter Cut off Frequency
Rear High Pass Filter Slope
Subwoofer Low Pass Filter Cut off Frequency
Subwoofer Low Pass Filter Slope
Subwoofer Low Pass Filter Phase
Speaker Size Rear
Speaker Size Subwoofer
10/ 12/ 15 Over/ None/ 6½/ 8 (inch)
"DTA"
Sound Management Item Range
⁄
"CABIN"
DTA Front/
0.00 — 9.67 (feet)
•
DTA Rear/
Set the type of vehicle for the sound position setting of
the DSP.
DTA Subwoofer
•
•
"SPEAKER"
"X'OVER"
Sound Management Item
Front High Pass Filter Cut off Frequency/ Through/ 30 — 100/ 120/
Rear High Pass Filter Cut off Frequency
Front High Pass Filter Slope/
Rear High Pass Filter Slope/
Subwoofer Low Pass Filter Slope
Sets the size and location of the speakers.
"DTA" (Digital Time Alignment).
Fine tune the difference in
distance between speakers
set with Cabin Setting. Use
together with <Position
Range
150/ 180/ 220/ 250 (Hz)
-12/ -18/ -24 dB/Oct
Control> (page 13)
Subwoofer Low Pass Filter Cut off
Frequency
30 — 100/ 120/ 150/ 180/
220/ 250 (Hz)/ Through
Subwoofer Low Pass Filter Phase
Normal/ Reverse
|
12
English
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Exit Sound Management mode
Range
0.00 — 3.33 (feet)
Press the [FNC] button.
5 Exit Position mode
Press the [FNC] button.
Position Control
⁄
•
About the position setting
1 Enter Position mode
First, set the using environment with “DTA” in <Sound
Management system> (page 12).
Preset position setting is for selecting the actual listening
position.
Using the Control knob, select "DSP" > "SND
CONT" > "POSITION".
For the operation method, refer to <Function
Control mode> (page 11).
Manual position setting is for further adjustment of the
position selected in preset position setting. This setting
value can be memorized for each preset position.
When using the Subwoofer Left and Subwoofer Right as
a single sub woofer, set the left side and right side to the
same value.
2 Select the Position item to adjust
Turn the Control knob or push it towards left
or right.
•
•
Icon
"PRESET"
"MANUAL"
Position Item
Preset Position
Manual Position
Preset Position initial settings
Preset Position
Front
Rear
Subwoofer
Left Right Left Right Left Right
ALL
0
0
1.17
0
0
1.17
0
0
0
1.17
0
1.17
0
0
0
0
0
0
0
0
0
3 Enter the Position item
Front-Left
Front-Right
Front
Press the Control knob.
4 Adjust the Position item
0
3.33 3.33
Preset Position Setting
Push the Control knob towards right or left.
Each time you push the knob, the setting alternates
between the settings shown in the table below.
Range
All/ Front-Left/ Front-Right/ Front
Manual Position Setting
1 Select the items to adjust for Position.
Push the Control knob towards up or down.
Display
Position Item
Front Left
Rear Left
Subwoofer Left
Front Right
Rear Right
"L" "FRONT"
"L" "REAR"
"L" "SW"
"FRONT" "R"
"REAR" "R"
"SW" "R"
Subwoofer Right
2 Adjust the Position.
Turn the Control knob or push it towards left
or right.
Each time you push the knob, the setting
alternates between the settings shown in the
table below.
English
|
13
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Each time you push the knob, the item to be
adjusted alternates between the items shown in
the table below.
Equalizer Control
1 Select the source to adjust
Press the [SRC] button.
3 Adjust the Equalizer.
Turn the Control knob or push it towards left
or right.
Each time you push the knob, the setting
alternates between the settings shown in the
table below.
Refer to <Selecting the Source> (page 8).
2 Enter Equalizer Control mode
Using the Control knob, select "DSP" > "SND
CONT" > "EQ".
For the operation method, refer to <Function
Display Equalizer adjustment item
Range
Control mode> (page 11).
"F0"
Equalizer Front Center Frequency/ Refer to the
3 Select the Equalizer Control item to adjust
Turn the Control knob or push it towards left
or right.
Equalizer Rear Center Frequency
followings.
"Q"
Equalizer Front Quality/
Equalizer Rear Quality
0.25/ 0.50/ 1.00/
2.00
"Gain" Equalizer Front Level/
Equalizer Rear Level
–9/ -7/ -5/ -3/ -2/
-1/ 0/ +1/ +2/ +3/
+5/ +7/ +9
Icon
Equalizer Control Item
System Q Setting
Equalizer Front Setting
Equalizer Rear Setting
"PRESET"
"FRONT"
"REAR"
"Effect" Equalizer Front Effect/
Equalizer Rear Effect
OFF/ ON
(BAND1 only)
4 Enter the Equalizer Control item
Press the Control knob.
⁄
•
The frequency which can be selected by each Frequency
band is shown below.
5 Adjust the Equalizer control item
System Q Setting
Turn the Control knob or push it towards left
or right.
Each time you push the knob, the setting alternates
between the settings shown in the table below.
Band
Band1
Band2
Band3
Band4
Frequency
60/ 80/ 100/ 120/ 160/ 200 Hz
250/ 315/ 400/ 500/ 630/ 800/ 1k Hz
1.25/ 1.6/ 2/ 2.5/ 3.15/ 4 kHz
5/ 6.3/ 8/ 10/ 12.5/ 16 kHz
Display
Sound setting
•
"Effect"
"User"/ "Natural"/ "Rock"/ "Pops"/ User/ Natural/ Rock/ Pops/ Easy/
"Easy"/ "Top40"/ "Jazz"
Amplifies the range lower than the center frequency as
well as the low center frequency.
Top 40/ Jazz
4 Exit frequency band.
Press the Control knob.
⁄
•
•
User memory:
The values set on the <Equalizer Front Setting/ Equalizer
Rear Setting>.
To get the best sound, first go through <Sound
Management system> (page 12).
6 Exit Equalizer Control mode
Press the [FNC] button.
Equalizer Front Setting/
Equalizer Rear Setting
WOW HD Control
1 Select a frequency band you wish to adjust.
Turn the Control knob or push it towards left
or right.
Each time you push the knob, the band alternates
between "1" (Band 1) and "4" (Band 4).
2 Select the items to adjust for Equalizer.
Push the Control knob towards up or down.
1 Select the source to adjust
Press the [SRC] button.
Refer to <Selecting the Source> (page 8).
2 Enter WOW HD Control mode
Using the Control knob, select "DSP" > "SND
CONT" > "WOW HD".
For the operation method, refer to <Function
Control mode> (page 11).
|
14
English
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Select the WOW HD Control item to adjust
Turn the Control knob or push it towards left
or right.
Memory mode
Storing the values of DSP in memory.
Press the Control knob.
1 Adjust the item you wish to put in memory
By referring to <Sound Management system>
(page 12), <Position Control> (page 13), and
<Equalizer Control> (page 14), adjust the item you
wish to put in the memory.
Icon
WOW HD Control Item
"PRESET"
Preset WOW HD
"FRONT" >"FOCUS" FOCUS
>"TruBass" TruBass Front
>"Space" SRS 3D Space Control
>"Center" SRS 3D Center Control
>"Defini" Definition Front
2 Enter Memory mode
Using the Control knob, select "DSP" > "PRESET"
> "MEMORY".
"REAR" >"TruBass" TruBass Rear
>"Defini" Definition Rear
For the operation method, refer to <Function
Control mode> (page 11).
4 Adjust the WOW HD control item
Turn the Control knob or push it towards left
or right.
Each time you push the knob, the setting alternates
between the settings shown in the table below.
3 Select the number to put in the memory
Turn the Control knob.
4 Determine whether to put the Audio Preset in
the memory
Press the Control knob.
WOW HD Control Item
Preset WOW HD
FOCUS
Range
"Memory?" is displayed.
Middle/ High/ User/ Through/ Low
OFF/ 1 — 9
5 Put the Audio Preset in the memory
Select "YES" using the Control knob.
"Memory Completed" is displayed.
TruBass Front/
TruBass Rear
OFF/ 1 — 9
SRS 3D Space Control
SRS 3D Center Control
Definition Front/
Definition Rear
OFF/ 1 — 9
-4 — Neutral — 4
OFF/ 1 — 9
6 Exit Memory mode
Press the [FNC] button.
⁄
•
•
•
"Memory 1": When you press the Reset, all the sources
will be the setting value which is registered.
"Memory 1", "Memory 2":
⁄
•
•
Preset WOW HD:
FOCUS, TruBass, 3D Space Control, 3D Center Control
and Definition are all set.
FOCUS: Adjusts the vertical position of the front speaker
and sound image by virtual adjustment.
TruBass: Assists the playback for the super bass sound.
SRS 3D Space Control: Adjusts the soundscape.
SRS 3D Center Control:
The memory cannot be erased by the Reset button.
The following items cannot be registered.
System Q Setting
•
•
•
Adjusts the center image such as vocal part in music.
Definition:
•
Improves sound quality in high range and creates clear
sound.
5 Exit WOW HD Control mode
Press the [FNC] button.
⁄
•
To get the best sound, first go through <Sound
Management system> (page 12).
English
|
15
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Memory Recall mode
Display Type Selection
Recall the value in the memory by the memory
mode.
Changing the display mode.
1 Enter Display Type Selection mode
Using the Control knob, select "DISPLAY" >
"TYPE".
1 Select the source to adjust
Press the [SRC] button.
For the operation method, refer to <Function
Control mode> (page 11).
2 Enter recall mode
Using the Control knob, select "DSP" > "PRESET"
> "RECALL".
2 Select the Display Type
Turn the Control knob.
For the operation method, refer to <Function
Control mode> (page 11).
Select from the following display types:
Display
"TYPE SELECT [A]"
Display Type
3 Select the recall item
Select the recall number using the Control
knob.
9
!
Press the Control knob.
Recall the value put by <Memory mode> (page
15).
1
"TYPE SELECT [B]"
"TYPE SELECT [C]"
"TYPE SELECT [D]"
"TYPE SELECT [E]"
9
2
"Recall?" is displayed.
3
3
4 Recall the Audio Preset
Select "YES" using the Control knob.
"Recall Completed" is displayed.
9
0
2
3
3
5 Exit Memory Recall mode
Press the [FNC] button.
9
7
7
8
@
3 Exit Display Type Selection mode
Press the Control knob.
4 Enter Display Mode Selection mode (Display
Type B/ Display Type C only)
Using the Control knob, select "DISPLAY" >
"MODE".
|
16
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Type A
5 Select the Display Mode
Turn the Control knob.
Select from the following display mode:
Status Setting
Determine whether the On and Off statuses of
various functions are to be displayed on the Display
Type A.
Mode
B-1/
C-1
"TYPE SELECT [B]"
9
"TYPE SELECT [C]"
9
2
0
0
0
2
1 Enter Status Setting mode
Using the Control knob, select "DISPLAY" >
"STATUS".
For the operation method, refer to <Function
Control mode> (page 11).
3
3
3
3
B-2/
C-2
9
4
5
5
5
9
9
4
5
5
5
2 Select the Status display
B-3/
C-3
9
6
6
Turn the Control knob.
3 Exit Status Setting mode
Press the Control knob.
6 Exit Display Mode Selection mode
Press the Control knob.
Display Type A
⁄
• 1, 2, 3, 4, 5, 6, 7, 8 Text display part
9 Status display
Graphic Display Selection
Changing the graphic Display.
0 Icon display part
! Graphic display part
@ G-Analyzer display part
To change the information by the Display Type, refer
to the page on the following table for the methods to
alternate by the Display Type.
1 Enter Graphic Display Selection mode
Using the Control knob, select "DISPLAY" >
"GRAPHIC".
•
For the operation method, refer to <Function
Control mode> (page 11).
Display Type
Text 1
A
B-1 B-2 B-3 C-1 C-2 C-3
D
E
18
—
18
18
—
18
—
—
—
—
18
—
18
18
—
18
—
—
—
—
18
—
—
—
—
—
18
—
—
—
—
—
—
—
—
—
—
—
—
—
20
2 Select the graphic display
Turn the Control knob or push it towards left
or right.
Text 3
—
—
—
—
—
17
—
17
—
Text 4
—
—
—
—
—
—
—
—
—
—
—
—
—
Text 5
18
18
Select from the following displays:
Text 6
—
—
—
—
—
—
—
—
—
Graphic display
Movie 1 – 2
Spectrum analyzer 1 – 8
Wallpaper 1 – 12
Downloaded Wallpaper*
Wallpaper scan
Display
Text 7
—
—
—
—
—
—
—
20 20 20
Status 9
Icon 0
Graphic !
G-Analyzer @
—
—
—
—
—
—
"SCAN"
•
•
•
With Display type D, text is displayed between the top
and bottom rows when blank is set in the top or bottom
row.
For the Satellite radio source, the text display part 6 is
divided between top row and bottom low for B-3 mode
or C-3 display mode.
* For Download Wall Paper, refer to <Picture downloading>
(page 52).
3 Exit Graphic Display Selection mode
Press the Control knob.
⁄
Text display part 6
•
During standby, Spectrum analyzer cannot be selected.
If whole information cannot be displayed within four
rows, hold down on [FM] of the Control knob for at
least 1 second to display the remaining portion of the
information.
English
|
17
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Display Type A/ Display Type B/ Display Type C/
Display Type D
The text display
Text Display Selection
In Tuner source
Information
Station name preset
Title & Artist name* (FM)
Station name* (FM)
Radio text plus* (FM)
Radio text (FM)
Frequency
Spectrum Analyzer & Clock
Clock
Date
Display
"SNPS"
Condition
134
Changing the text display.
1 Enter Text Display Selection mode
Using the Control knob, select "DISPLAY" >
"TEXT".
For the operation method, refer to <Function
Control mode> (page 11).
134567
134567
134567
134567
"Title/Artist"
"Station Name"
"Radio Text Plus"
"Radio Text"
"Frequency"
"Speana/Clock"
"Clock"
1
4
345
2 Select the text
1
7
7
7
Turn the Control knob or push it towards left
or right.
1345
1345
"Date"
"Blank"
Blank
See <The text display> (page 18).
* Information of Radio text plus is displayed.
Select the row (only for display type with
multiple rows)
In CD & External disc source
Push the Control knob towards up or down.
The cursor (‰) moves to the selected text display
part.
Information
Disc title
Track title
Track number & Play time
Disc name preset
Spectrum Analyzer & Clock
Clock
Display
Condition
134567
"Disc Title"
"Track Title"
"P-Time"
"DNPS"
"Speana/Clock"
"Clock"
134567
1
4
3 Exit Text Display Selection mode
1345
345
1
7
Press the Control knob.
7
7
7
⁄
1345
1345
Date
Blank
"Date"
"Blank"
•
When LX-AMP is connected, the item setup by the
Display mode of LX-AMP is displayed. (Other than B-3 or
C-3 display mode)
•
•
•
When the music number exceeds 1000, only the last 3
digits of its number are displayed.
Music title, Artist name, and Album name cannot be
displayed in WAV file.
When playing music from iPod or music edited by "Music
Editor", the folder name display may show something
different such as playlist or artist name depending on
the music selection procedure.
Same information cannot be displayed in text display
part. However, the blank display is able to have multiple
selections.
In Audio file source
Information
Display
Condition
134567
134567
134567
134567
Music title & Artist name
Album name & Artist name
Folder name
"Title/Artist"
"Album/Artist"
"Folder Name"
"File Name"
"P-Time"
"Speana/Clock"
"Clock"
"Date"
File name
1
4
Play time & Music number
Spectrum Analyzer & Clock
Clock
Date
Blank
345
•
•
1
7
7
7
1345
1345
If the selected display item does not have any
information, alternative information is displayed. May be
blank depending on the displayed row.
"Blank"
In Standby
Information
Standby
Clock
Date
Blank
Display
"Source Name"
"Clock"
"Date"
"Blank"
Condition
1
4
1345
1345
1345
7
7
7
|
18
English
Download from Www.Somanuals.com. All Manuals Search And Download.
In Auxiliary input source
Display Type A/ Display Type B/ Display Type C
Font Color Selection
Selecting the display font color.
Information
Auxiliary input name
Spectrum Analyzer & Clock
Clock
Date
Display
Condition
1
4
"Source Name"
"Speana/Clock"
"Clock"
"Date"
"Blank"
345
1
7
7
7
1 Enter Font Color Selection mode
Using the Control knob, select "DISPLAY" >
"COLOR".
1345
1345
Blank
For the operation method, refer to <Function
Control mode> (page 11).
In HD Radio source
Information
Station name
Title
Frequency
Spectrum Analyzer & Clock
Clock
Date
Display
"Station Name"
"Title"
"Frequency"
"Speana/Clock"
"Clock"
"Date"
"Blank"
Condition
134
2 Select the text display part
Select the character color/ outline color
(Display Type A only)
134567
1
4
345
Push the Control knob towards up or down.
1
7
7
7
Display
Setting
1345
1345
"FILL-IN"
"OUTLINE"
The color of the text fill.
The color of the text outline.
Blank
In Satellite radio source
Select the row (only for display type with
multiple rows)
Push the Control knob towards up or down.
The cursor (‰) moves to the selected text display
part.
Information
Channel Name
Music Title
Display
Condition
134567
134567
134567
134567
134567
134567
134567
"Channel Name"
"Song Title"
"Artist Name"
"Composer Name"
"Category Name"
"Label Name"
"Comment"
"Channel Number"
"Speana/Clock"
"Clock"
Artist Name
Composer name
Category Name
Label Name
3 Select the Font Color
Basic color (12 colors)
Push the Control knob towards right or left.
Comment
1
4
Band & Channel Number
Spectrum Analyzer & Clock
Clock
345
Detail color (115 colors)
Turn the Control knob.
1
7
7
7
1345
1345
Date
"Date"
4 Exit Font Color Selection mode
Blank
"Blank"
Press the Control knob.
⁄
•
See <Display Type Selection> (page 16) for the display
position of "Condition".
English
|
19
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Display Type C
2 Select the G-Analyzer display
Turn the Control knob.
Select from the following displays.
Icon Display Switching
Changing the Icon Display.
G-Force Sensor display
1 Enter Icon select mode
Using the Control knob, select "DISPLAY" >
"SIDE".
G- Graphic display
G-Counter display
2 Switch the Icon display
Turn the Control knob or push it towards left
or right.
Select from the following displays:
⁄
Icon display
Source graphic
Text label
Display
"Source"
"Text"
•
•
•
G-Graphic display
- Graphic: Displays the condition of G in horizontal
direction (e.g; when turning the curve) by the graphic.
- Text: The maximum value of acceleration G, right
direction G, and left direction G is displayed by the
numerical value. The value of G is only the reference, so
is different from the actual value.
Album art (iPod or "Music Editor" media)
"Photograph"
3 Exit Icon select mode
Press the Control knob.
G-Counter display
⁄
Adds the point of the acceleration level. The point is
determined after a lapse of 1 hr drive or at power off
(ACC Off), and then it will be displayed by the graph.
Furthermore, the G-Counter displays the average of the
past data by the line. (The scale of graph is determined
along with the largest point among the past 10 data.)
The value of G-Meter display and G-Counter display can
be reset by <G-Analyzer Reset> (page 22).
•
•
•
The Album art display function is not used to display the
image corresponding to the tag recorded in the Audio
file.
If Album art display is selected during playback of an
iPod or "Music Editor" media on which no album art is
recorded, a source icon is displayed.
During Album art downloading, "Down-loading" is
displayed. Downloading requires a maximum of 30
seconds.
3 Exit G-Analyzer display selection mode
Press the Control knob.
Display Type E
Display Type E
G-Analyzer display Selection
Changing the G-Analyzer display.
G-Analyzer Stop Watch
The control of stop watch can be started by G-
Analyzer function.
⁄
•
Before alternating G-Analyzer display, you are required to
setup <G-Counter Level setting> (page 22), <G-Analyzer
Calibration setup> (page 22), <G-Analyzer vehicle weight
setup> (page 23) and <G-Analyzer vehicle class setup>
(page 23).
¤
•
Do not use G-Analyzer stop watch on the Public roads.
1 Enter G-Analyzer Stop Watch mode
Using the Control knob, select "DISPLAY" >
"GMA" > "S.WATCH".
For the operation method, refer to <Function
Control mode> (page 11).
1 Enter G-Analyzer display selection mode
Using the Control knob, select "DISPLAY" > "G-
MENU".
For the operation method, refer to <Function
Control mode> (page 11).
"STOP WATCH" is displayed.
2 Make the counter ready
Press the Control knob.
"Ready" is displayed.
|
20
English
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Start Count
1 Enter G-Analyzer Horsepower Analysis mode
Using the Control knob, select "DISPLAY" >
"GMA" > "HP".
When G in the vertical direction is detected during
the travel, the count automatically starts.
"Running" is displayed.
For the operation method, refer to <Function
Control mode> (page 11).
"HORSEPOWER" is displayed.
Previous max power and record are displayed.
⁄
•
You can also start the counter by pressing the Control
knob.
2 Begin measurement
Press the Control knob.
"Ready" is displayed.
4 Stop Count
Press the Control knob.
"Stop" is displayed.
3 Start the car
⁄
"Measure" is displayed.
•
The control will start again when you accelerate or press
the Control knob.
After 15 seconds of measurement, the result is
displayed.
Do the operation after step 2.
Display the result
The graph shows the variation in horsepower
between 0.1 to 15.0 seconds. The maximum power
is displayed in red and the markings provided at
intervals of 5 seconds are displayed in blue.
When you Reset the Count
(While "Stop" is displayed)
Press the Control knob for at least 1 second.
⁄
¤
•
You can reset of count when the count is stopped.
•
Pressing the Control knob also begins the measurement.
To prevent danger, push the control knob before starting
the car.
5 Exit G-Analyzer Stop Watch mode
Press the [FNC] button.
4 To display the maximum power in the section
Push the Control knob towards right or left.
Each time you push the Control knob, the
⁄
•
When Power off (ex; ACC OFF) while counting, the value
of 1 second or less will be "00".
maximum power in the section is displayed.
5 Exit G-Analyzer Horsepower Analysis mode
Press the [FNC] button.
Display Type E
⁄
G-Analyzer Horsepower Analysis
This measures the horsepower and displays graph
and max power. It automatically saves the highest
record.
•
Like your vehicle’s speedometer, G-Analyzer is no more
than a measuring function. The HP or G value measured
by this unit may not be completely accurate due to its
simplified method of measurement. The G-Analyzer is
only for reference and should not be used to confirm the
horsepower specifications of your vehicle.
Measuring after starting the car lowers the accuracy.
The record will not be renewed if the measurement is
discontinued.
¤
•
•
•
Do not use G-Analyzer Horsepower Analysis on the
Public roads.
Do not use this product in any way that prevents you
from driving safely.
Follow all driving laws and use common sense when
using this product.
•
•
•
•
The graph’s scale adjusts automatically to the
horsepower value.
The value of max power and record can be reset by <G-
Analyzer Reset> (page 22).
⁄
•
Before alternating G-Analyzer Horsepower Analysis, you
are required to setup <G-Analyzer vehicle weight setup>
(page 23) and <G-Analyzer vehicle class setup> (page
23).
English
|
21
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Display Type E
3 Exit G-Counter Level setting mode
Press the Control knob.
G-Analyzer Reset
⁄
Resets the value of G-Meter, G-Counter and G-
Analyzer Horsepower Analysis.
•
In the case of driving situations calling for few
accelerations, set the G-Point up to "Level 1". In the case
of frequent accelerations, set it up to "Level 3".
1 Enter G-Analyzer Reset mode
Using the Control knob, select "DISPLAY" >
"GMA" > "RESET".
For the operation method, refer to <Function
Control mode> (page 11).
"G-RESET" is displayed.
In Standby mode
Display Type E
G-Analyzer Calibration setup
G-Analyzer requires calibration for horizontal
acceleration and braking.
2 Select the Reset item
Turn the Control knob.
Display
Setting
⁄
"Meter Reset"
"Power Reset"
Reset the value of G-Meter.
Reset the value of G-Analyzer Horsepower
Analysis.
•
To ensure accurate calibration, go through the following
steps at a level place where you can move the vehicle
straight ahead.
"Counter Reset"
Reset the value of G-Counter.
1 Park the vehicle in a horizontal location
2 Enter G-Analyzer Calibration setup mode
Using the Control knob, select "DISPLAY" >
"GMA" > "CALIB".
For the operation method, refer to <Function
Control mode> (page 11).
3 Determine the item you want to reset
Press the Control knob.
4 Reset the value
Select "YES" using the Control knob.
"Reset OK" is displayed.
"G-CALIBRATION" is displayed.
5 Exit G-Analyzer Reset mode
Press the [FNC] button.
3 Start Calibration of horizontal direction
Press the Control knob.
Once "Move Forward" appears on the display, the
vehicle must be advanced.
Display Type E
4 Start Calibration of straight direction
Start moving the vehicle ahead.
Calibration of straight direction automatically starts.
When the Calibration is finished, "Calibration OK" is
displayed.
G-Counter Level setting
Calibrating G-Point. Setting the level according to
the kinds of vehicles.
1 Enter G-Counter Level setting mode
Using the Control knob, select "DISPLAY" >
"GMA" > "LEVEL".
⁄
•
If you fail to complete the calibration, "No Calibration" is
displayed. In such a case, repeat steps 1 through 4.
For the operation method, refer to <Function
Control mode> (page 11).
"G-COUNTER LEVEL" is displayed.
5 Exit G-Analyzer Calibration setup mode
Press the [FNC] button.
2 Select the G-Counter Level
Turn the Control knob.
Display
"Level 1"
"Level 2"
"Level 3"
Setting
Counter is easy to go up.
Counter is hard to go up.
|
22
English
Download from Www.Somanuals.com. All Manuals Search And Download.
In Standby mode
Display Type E
Display
"Mid Size"
"Full Size"
"SUV"
"Van/ Mini-Van"
"Pickup Truck"
"Sporty"
G-Analyzer vehicle weight setup
Enter vehicle weight to calculate horsepower.
1 Enter G-Analyzer vehicle weight setup mode
Using the Control knob, select "DISPLAY" >
"GMA" > "GAUGE" > "WEIGHT".
"Compact"
For the operation method, refer to <Function
Control mode> (page 11).
"WEIGHT INPUT" is displayed.
3 Exit G-Analyzer vehicle class setup mode
Press the Control knob.
2 Select the weight numbers
Turn the Control knob.
⁄
•
The weight input range is between 1000-9999 lbs.
3 Select the digits to enter
Push the Control knob towards right or left.
4 Repeat steps 2 and 3, and complete the weight
input.
5 Exit G-Analyzer vehicle weight setup mode
Press the Control knob.
In Standby mode
Display Type E
G-Analyzer vehicle class setup
Enter vehicle class to calculate horsepower.
1 Enter G-Analyzer vehicle class setup mode
Using the Control knob, select "DISPLAY" >
"GMA" > "GAUGE" > "CLASS".
For the operation method, refer to <Function
Control mode> (page 11).
"CLASS SELECT" is displayed.
2 Select vehicle class
Turn the Control knob.
Each time you push the knob, the vehicle class
alternates between the modes shown in the table
below.
English
|
23
Download from Www.Somanuals.com. All Manuals Search And Download.
General features
Station/Disc Naming (SNPS/DNPS)
Attaching a title to a Station or CD.
9 Exit Menu mode
Press the [FNC] button.
⁄
1 Receive/play the station/disc you want to
attach a title to
•
When operation stops for 10 seconds the name at that
time is registered, and Name Set mode closes.
Memory numbers
•
⁄
- FM/AM: 30 stations
- Internal CD player: 10 discs
•
A title cannot be attached to MD or Audio file media.
- External CD changer/ player: Varies according to the
CD changer/ player. Refer to the CD changer/ player
manual.
Change the title of station/CD by the same operation
used to name it.
2 Enter Menu mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 11).
•
3 Select Name set mode
Turn the Control knob.
Select the "Name Set" display.
Angle Control
Setting the panel angle.
4 Enter Name set mode
Press the Control knob for at least 1 second.
1 Enter Angle Control mode
5 Move the cursor to the enter character
position
Push the Control knob towards right or left.
Using the Control knob, select "ANGLE".
For the operation method, refer to <Function
Control mode> (page 11).
6 Select the character type
Press the Control knob.
Each time you press the knob, the character type
alternates between the types shown in the table
below.
2 Set the panel angle
Turn the Control knob to right or push it
towards right.
Each time you turn the Control knob, the panel
angle is changed in four levels.
Character type
Alphabet upper case
Alphabet lower case
3 Exit Angle Control mode
Press the Control knob.
Numbers and symbols
Special characters (Accent characters)
7 Select the characters
Turn the Control knob or push it towards up or
down.
⁄
•
Enter characters by using a remote control with numbers
buttons.
Example: If you are entering "DANCE".
Character
"D"
"A"
"N"
"C"
Button
[3]
[2]
[6]
[2]
Times pressed
1
1
2
3
2
"E"
[3]
8 Repeat steps 5 through 7 and enter the name.
|
24
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Theft Deterrent Faceplate
The faceplate of the unit can be detached and taken
with you, helping to deter theft.
Removing the Faceplate
Press the Release button.
The faceplate is unlocked, allowing you to detach it.
¤
•
The faceplate is a precision piece of equipment and can
be damaged by shocks or jolts.
•
•
Keep the faceplate in its faceplate case while detached.
Do not expose the faceplate (and the faceplate case) to
direct sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
Reattaching the Faceplate
1 Align the shaft on the unit with the depression
on the faceplate.
2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to use
the unit.
English
|
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner features
Control knob
FM
ꢁ
D
AM
FNC
SRC AUTO/AME
ST indicator
Band display
Preset station number
Frequency display
Function icon
Tuning
Tuning Mode
Selecting the station.
Choose the tuning mode.
Press the [AUTO] button.
1 Select tuner source
Each time you press the button, the Tuning mode
alternates between the modes shown in the table
below.
Press the [SRC] button.
Select the "TUNER" display.
Refer to <Selecting the Source> (page 8).
Tuning mode
Display
Operation
2 Select the band
Auto seek
"Seek Mode: Automatic search for a station.
Auto1"
Push the Control knob towards [FM] or [AM].
Each time you push the knob toward [FM], it
switches between the FM1, FM2, and FM3 bands.
Preset station seek "Seek Mode: Search in order of the stations in
Auto2" the Preset memory.
Manual
"Seek Mode: Normal manual tuning control.
Manual"
3 Tune up or down band
Push the Control knob towards [4] or [¢].
⁄
•
During reception of stereo stations the "ST" indicator is
ON.
|
26
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of remote control
Auto Memory Entry
Putting stations with good reception in the memory
automatically.
Direct Access Tuning
Entering the frequency and tuning.
1 Select the band for Auto Memory Entry
1 Select the band
Push the Control knob towards [FM] or [AM].
Press the [FM] or [AM] button.
2 Open Auto Memory Entry
2 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
Press the [AME] button for at least 2 seconds.
When 6 stations that can be received are put in the
memory Auto Memory Entry closes.
"– – – –" is displayed.
3 Enter the frequency
Press the number buttons on the remote
control.
Example:
Preset Tuning
Recalling the stations in the memory.
Desired frequency
92.1 MHz (FM)
810 kHz (AM)
Press button
[0], [9], [2], [1]
[0], [8], [1], [0]
1 Select the band
Push the Control knob towards [FM] or [AM].
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
2 Enter Preset Tuning Select mode
Turn the Control knob.
3 Select a desired station in the memory
Turn the Control knob.
4 Recall the station
Station Preset Memory
Press the Control knob.
Putting a station in the memory.
Cancelling Preset Tuning
Press the [FNC] button.
1 Select the band
Push the Control knob towards [FM] or [AM].
2 Select the frequency to put in the memory
Push the Control knob towards [4] or [¢].
3 Enter Preset Memory mode
Using the Control knob, select "P.MEMORY".
For the operation method, refer to <Function
Control mode> (page 11).
4 Select the number to put in the memory
Turn the Control knob.
5 Determine the number to put in the memory
Press the Control knob.
6 Allow the determined number to take effect
Press the Control knob.
Cancelling the Preset Memory mode
Press the [FNC] button.
English
|
27
Download from Www.Somanuals.com. All Manuals Search And Download.
RDS features
Control knob
FM
ꢁ
D
AM
FNC
SRC
AUTO
Radio text
Function icon
PTY (Program Type)
Selecting the Program Type and searching for a
station.
9.
Adult Hits
Soft Rock
Top 40
Country
Oldies
Soft
Nostalgia
Jazz
Classical
R & B
Soft R & B
Language
Religious Music
Religious Talk
Personality
Public
"Adult Hits"
"Soft Rock"
"Top 40"
"Country"
"Oldies"
"Soft"
"Nostalgia"
"Jazz"
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
1 Enter PTY mode
Press the Control knob.
"PTY SELECT" is displayed.
⁄
"Classical"
•
The PTY function cannot be used during a traffic bulletin
"Rhythm & Blues"
"Soft R & B"
"Foreign Language"
"Religious Music"
"Religious Talk"
"Personality"
"Public"
or AM reception.
2 Select the Program Type
Turn the Control knob or push it towards up or
down.
No.
1.
Program Type
Speech
Display
"All Speech"
"All Music"
"News"
College
Weather
"College"
"Weather"
2.
Music
3.
News
4.
5.
6.
Information
Sports
Talk
"Information"
"Sports"
"Talk"
⁄
•
Speech and Music include the Program type below.
Music: No.7 — 19, 21
Speech: No.3 — 6, 20, 22 — 26
7.
8.
Rock
Classic Rock
"Rock"
"Classic Rock"
|
28
English
Download from Www.Somanuals.com. All Manuals Search And Download.
•
The Program Type can be put in the preset memory and
recalled quickly. Refer to the <Program Type preset>
(page 29).
4 Preset the Program Type
Press the Control knob for at least 1 second.
5 Exit Program Type preset mode
3 Search for the selected Program Type station
Push the Control knob towards [4] or [¢].
When you want to search for other stations, push
toward [4] or [¢] of the Control knob again.
Press the [FNC] button.
Recalling the preset Program Type
1 Enter PTY mode
Refer to <PTY (Program Type)> (page 28).
⁄
•
When selected Program Type is not found, "No PTY" is
displayed. Select another Program Type.
2 Enter Program Type preset mode
Press the [FNC] button.
4 Exit PTY mode
3 Select the number you want to recall from the
Press the Control knob.
memory
Turn the Control knob or push it towards left
or right.
Registration of a station as a PTY
Registering a Program Type for stations with no PTY
data.
4 Recall the Program Type
Press the Control knob.
5 Exit Program Type preset mode
Press the [FNC] button.
1 Receive the station you want to register
2 Select the Program Type to register
Refer to <PTY (Program Type)> (page 28).
Radio Text Scroll
Scrolling the displayed Radio text, Title/Artist name,
Station name or Radio text plus.
3 Register the Program Type
Press the [AUTO] button for at least 2 seconds.
Confirming the Program Type
Press the [AUTO] button.
The Program Type is displayed for 5 seconds.
Push the Control knob toward up for at least 2
seconds.
⁄
4 Exit PTY mode
•
When the <Display Illumination Control> (page 47) is set
to OFF, the display may black out while scrolling.
Press the Control knob.
Program Type preset
Putting the Program Type in the Preset button
memory and quick recall.
Presetting the Program Type
1 Select the Program Type to preset
Refer to <PTY (Program Type)> (page 28).
2 Enter Program Type preset mode
Press the [FNC] button.
3 Select the number you want to put in the
memory
Turn the Control knob or push it towards left
or right.
English
|
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/Audio file (USB/iPod/Internal Memory) control features
Control knob
ꢀ
ꢁ
D
FNC
SRC
IN indicator
Folder number
File number
Play time
Function icon
Eject the disc
1 Eject the disc
Press the [0] button.
Playing CD & Audio file
When there is no disc inserted
1 Open the panel
2 Return the panel to the original position
Press the [0] button.
Press the [0] button.
2 Insert a disc.
¤
⁄
•
You can eject the disc for 10 minutes after switching off
the engine.
•
When the faceplate slides open, it might interfere with
the shift lever or other vehicle function. If this happens,
pay attention to safety and move the shift lever or take
an appropriate action to remove the obstacle, then
operate the unit.
•
Insert the disc horizontal to the slot. If you insert the Disc
as you push down on the Disc, it may scratch the Disc.
⁄
•
For the audio files and discs you can play with this unit,
refer to <About Audio file> (page 5).
•
When a disc is inserted the "IN" indicator is ON.
When a disc is inserted
Press the [SRC] button.
Select the "Compact Disc" display.
Refer to <Selecting the Source> (page 8).
|
30
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing USB (iPod) device
Playing Internal Memory
Press the [SRC] button.
Select the "Internal Memory" display.
When the USB device is not connected
Connect the USB device
Playback of the file contained in the USB device
starts.
Refer to <Selecting the Source> (page 8).
When the USB device is connected
Playing External Disc
Playing discs set in the optional accessory disc
player connected to this unit.
Select USB source
Press the [SRC] button.
Select the "USB" (or "iPod") display.
Refer to <Selecting the Source> (page 8).
Press the [SRC] button.
Select the display for the disc player you want.
Refer to <Selecting the Source> (page 8).
Display examples:
⁄
•
•
•
For the audio files that can be played with this unit and
the devices that can be connected to this unit, refer to
<About Audio file> (page 5).
Display
"CD Changer"
"MD Changer"
Disc player
CD changer
MD changer
The word "iPod" appearing in this manual indicates the
iPod connected with the KCA-iP200 (optional accessory).
Refer to <About Audio file> (page 5).
If you start playback after connecting the iPod, the music
that has been played by the iPod is played first.
In this case, "RESUMING" is displayed without displaying
a folder name, etc. Changing the browse item will
display a correct title, etc.
⁄
•
The functions that can be used and the information that
can be displayed will differ depending on the external
disc players being connected.
•
When the iPod is connected to this unit, "KENWOOD" or
"✓" is displayed on the iPod to indicate that you cannot
operate the iPod.
Pause and play
Press the Control knob.
Each time you press the knob, the audio pauses or
plays.
•
•
•
When the USB device is connected to this unit, it can be
charged up provided that this unit is powered.
When the Multi Card Reader is used, refer to <Drive
Search> (page 32).
After you stopped playing a file contained in the USB
device, you can restart playing the file from the point
where you stopped its playback.
Even after removing the USB device, you can restart
playing the file from the point where you stopped its
playback as long as the files contained in the USB device
are all the same.
•
Be sure to insert the USB device connector as far as it will
go.
Removing the USB device
1 Set the remove mode as the USB source
Press the [0] button for at least 2 seconds.
"USB REMOVE" display blinks.
2 Remove the USB device.
English
|
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/Audio file (USB/iPod/Internal Memory) control features
Function of disc changer/ Audio file
Drive Search
Selecting the device inserted in the Multi Card
Disc Search/Folder/Album Search
Reader.
Switching between folders/albums contained in the
disc changer, media, or device being played now.
1 Put the playback to pause
Push the Control knob towards up or down.
Press the Control knob.
⁄
2 Select a device
•
Disabled when "RESUMING" is displayed on the iPod.
Push the Control knob towards up or down.
3 Restart playback
Press the Control knob.
Function of remote control
⁄
Direct Music Search
Doing Music Search by entering the music number.
•
This unit is compliant with Multi Card Readers with a
maximum of 4 slots.
•
If a device is inserted during connection of the Multi
Card Reader, it is not recognized. Select the Remove
mode with reference to <Playing USB (iPod) device>
(page 31), remove the Card Reader, and then insert the
memory.
1 Enter the music number
Press the number buttons on the remote
control.
⁄
•
You can select Direct music Search up to 999.
2 Do music Search
Fast Forwarding and Reversing
Press the [4] or [¢] button.
Cancelling Direct Music Search
Press the [38] button.
Fast Forwarding
Hold down toward [¢] with the Control knob.
Release to resume the playback.
⁄
•
This function is not available on iPod and the music
edited by "Music Editor".
Reversing
Hold down toward [4] with the Control knob.
Release to resume the playback.
⁄
•
There is no sound while the Audio file is being searched.
Function of disc changers with remote control
Direct Disc Search
Doing Disc Search by entering the disc number.
Music Search
1 Enter the disc number
Press the number buttons on the remote
control.
Switching between music contained in the disc or
folder being played now.
Push the Control knob towards [4] or [¢].
2 Do Disc Search
Press the [FM+] or [AM–] button.
Cancelling Direct Disc Search
Press the [38] button.
|
32
English
Download from Www.Somanuals.com. All Manuals Search And Download.
•
During random play, turn the control knob right to
randomly select the next song.
Play function of CD and Audio file
Setting up the Repeat Play and Scan Play.
1 Set up the play function
Using the Control knob, set your desired setup
item to On/Off.
Function of Audio file
File Select
For the operation method, refer to <Function
Selecting the music you want to listen to from the
device or media being played now.
Control mode> (page 11).
When the play function is turned on, “ON” is
displayed.
1 Enter File Select mode
Display
Icon
Function
Turn the Control knob.
"File Scan"
"SCAN"
Successively plays the audio files in the
current folder or genre.
2 Search for music
Select the category item using the Control
knob.
"Folder RDM" "RANDOM" Plays the audio files in the current folder
or genre at random.
"All Random" "ALL RDM" Plays the audio files in the current disc,
USB device or Internal Memory at random.
Operation system for iPod
Operation type
Movement between items Turn the Control knob.
Selection of item Press the Control knob.
Return to previous item Push the Control knob towards up.
Operation
"File Repeat" "FILE REP" Plays the current audio file repeatedly.
"Folder Repeat" "FOLDER Plays the audio files in the current folder
REP"
or genre repeatedly.
"(Track) Scan" "SCAN"
Plays the beginnings of the music on the
current CD/MD one after another for 10
seconds each.
Return to first item
Push the Control knob towards up for at least
1 second.
"Disc Random" "RANDOM" Plays the music on the current CD/MD
at random.
"Magazine RDM""M.RDM" Plays the music in the disc changer at
random.
"(Track) Repeat" "TRACK REP"Plays the current music on the current
CD/MD repeatedly.
Operation system for other than iPod
Operation type Operation
Movement between items Turn the Control knob.
Selection of item
Push the Control knob towards right.
Return to previous item Push the Control knob towards left.
"Disc Repeat" "DISC REP" Plays the music on the current CD/MD
repeatedly.
Return to first item
Push the Control knob towards left for at least
1 second.
2 Select an option for the selected item
Press the Control knob.
Pressing the Control knob switches between
The "2" or "3" symbol shown beside the displayed
item indicates that the item is preceded or followed
by another item.
options.
Selecting a music will play it from the beginning.
3 Exit Play Function Set mode
Cancelling File Select
Press the [FNC] button.
Press the [FNC] button.
⁄
⁄
•
Only the icons available to the current source are
displayed.
•
Even when the iPod is connected, you can change the
operation method from <Operation method for iPod> to
<Operation method for other than iPod>. Refer to <iPod
mode Setting> (page 46).
•
Location played with "File Scan"
- Audio file: First 10 seconds
- Music Editor media: First 10 seconds or the part picked
by Intro Skip (30 seconds)
During Intro Skip, turn the control knob left or right to
change the song.
The scan method depends on the Music Editor setting.
See the Music Editor help for details.
English
|
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/Audio file (USB/iPod/Internal Memory) control features
Text/Title Scroll
Scrolling the displayed CD text, Audio file text, or
MD title.
Push the Control knob toward up for at least 2
seconds.
⁄
•
When the <Display Illumination Control> (page 47) is set
to OFF, the display may black out while scrolling.
|
34
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording & Downloading
Control knob
ꢀ
FNC
Memory size
Function icon
•
Do not press the reset button or remove the battery
while recording, copying, or erasing. Otherwise, the
audio file in the internal memory may be lost.
The audio file in the internal memory cannot be copied
to another media.
Only the following controls can be used while recording,
copying, or erasing:
- Volume
About Internal Memory
Audio files can be stored in internal memory. The
stored audio files can be played in the same manner
as CDs.
•
•
Audio files can be stored by recording a music CD or
copying from a USB device.
To play the stored audio file, refer to <CD/Audio file
(USB/iPod/Internal Memory) control features> (page
32).
- Attenuator
- Power off
When recording or copying is interrupted
If ACC is turned off while recording or copying, a
screen to confirm whether to continue recording
or copying appears next time ACC is turned on
(Resume function).
1 When "Checking the condition..." is displayed,
"Continue Ripping?" or "Continue USB Copy?" is
also displayed.
2 Turn on the engine and then select "YES".
3 Press the Control knob.
Recording or copying resumes.
•
Built-in flash memory
512 MB
Max. recording time/ tracks
Approx. 16 hours/ Approx. 240 tracks
(Assuming that each tracks is in the 64 kbps WMA
format with playback time of about 4 min.)
•
⁄ Notes on recording, copying, and erasing
•
Kenwood will not be responsible for the loss or damage
to the music or sound data in case recording fails due to
machine fault or failure.
•
•
Audio files may be lost if the engine is started while
recording or copying.
Record or copy with the engine running.
Next page 3
English
|
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording music CD
Music CD can be compressed and stored in internal
memory.
⁄
•
Resume is canceled if "CANCEL" or "NO" is selected.
- "CANCEL": Press the Control knob.
- "NO": Select "NO" using the Control knob. Press the
Control knob.
CD
(;Int Mem)
•
The resume function may be disabled depending the
condition of the vehicle or battery. The audio file may be
lost if the resume function is disabled.
vꢀ
vꢆ
vꢇ
vCD000_001
;CD001
Record or copy while the engine is running.
vCD001_003
v.
vCD001_010
⁄
When music CD is inserted
•
Read <About Internal Memory> (page 35) before
starting copy.
Setting the recordable time
Set the recordable time for recording music CD.
•
Music CD can be recorded only from the internal CD.
Recording is performed at x1 speed.
1 Enter Mode setting
1 Insert a CD-DA
Using the Control knob, select "IMPORT CD" >
"MODE SET".
Insert the music CD to record.
Refer to <Playing CD & Audio file> (page 30).
For the operation method, refer to <Function
Control mode> (page 11).
2 Change to import mode
Using the Control knob, select "IMPORT CD" >
"IMPORT".
2 Set the recordable time
Turn the Control knob.
For the operation method, refer to <Function
Control mode> (page 11).
Display
"Standard"
"Long Play"
Setting
Standard recording
Max. recording time*
Approx. 8 hours
Approx. 12 hours
3 Select record mode
Push the Control knob towards right or left.
Multiple song record mode is set when the control
knob is turned right and single song record mode
is set when it is turned left.
"Super Long Play" Extended time recording Approx. 16 hours
3 Exit Mode setting
Press the Control knob.
4 Select the song to record
Turn the Control knob or push it towards up or
down.
⁄
•
* The maximum recordable time is obtained when there
is no other file. The actual recording time depends on
the song.
Record mode
Single song
Multi song
Operation
Selects a single song.
Selects all songs or from specified song to
the last song.
•
The sound quality for Extended recording is lower than
for Standard recording.
5 Confirm the song
Press the Control knob.
6 Name the target file or folder
Using the Control knob, select "NAME SET".
Recording starts if "SKIP" is selected.
7 Enter Name set mode
Press the Control knob.
|
36
English
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Enter the name
Operation type
Move the cursor to the enter
character position
Select the character type*
Select the characters
⁄
•
Recording is possible only from music CD and not from
Operation
Push the Control knob towards right
or left.
Press the Control knob.
Turn the Control knob or push it
towards up or down.
CD containing audio files. Copy audio files from USB
device.
•
Sound may skip due to vibration when the vehicle is in
motion. The song will be recorded together with the
skip.
•
•
•
Normal recording or playback may not be possible with
some CDs.
DSP cannot be enabled while recording, but it can be
enabled during playback.
When a song is selected, the remaining recording time is
decreased by the length of the recording. The remaining
recording time is a rough estimate. It may increase of
decrease when recording is completed.
If recording is canceled or if space runs out while
recording, the recorded songs will remain.
There is no tag (song information) on the recorded file.
File name or folder name may contain up to 16
characters.
* Each time you press the knob, the character type
alternates between the types shown in the table below.
Character type
Alphabet upper case
Alphabet lower case
Numbers and symbols
Special characters (Accent characters)
•
⁄
•
Enter characters by using a remote control with numbers
buttons.
•
•
Example: If you are entering "DANCE".
•
•
•
If a folder name is specified when recording multiple
songs, the file name will be "foldername_tracknumber".
If there is a file or folder with the same name, a number
is added as "Name_001".
If file name or folder name is not specified:
- Single song recording: Files are named sequentially
starting from "CD000_001.wma".
Character
Button
Times pressed
"D" "A"
"N" "C"
"E"
[3]
2
[3]
1
[2]
1
[6]
2
[2]
3
9 Confirm the name
Using the Control knob, select "ENTER".
- Multi song recording: Folders are named sequentially
starting from "CD001".
- File and folder name are incremented successively
from the last number even if files in the middle are
deleted. The number returns to 001 when 999 is
reached.
10 Start recording
Press the Control knob.
Recording track no. and remaining time
- Setting file name and folder name is recommended.
"Completed" is displayed when recording
completes.
Canceling recording
1 Cancel recording
Press the [FNC] button.
Exits Import Mode when pressed by step 4.
2 Select "YES"
Select "YES" using the Control knob.
11 Exit Record mode
Select "EXIT" using the Control knob.
Returns to step 3 if "NEXT" is selected.
English
|
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording & Downloading
Copying from USB device
Copy audio files and folders from USB device to
internal memory.
5 Exit Copy mode
Select "EXIT" using the Control knob.
Returns to step 3 if "NEXT" is selected.
⁄
USB
(
;
)
(
;
Int Mem)
vFile1
Folder4
•
If a folder is selected, the files in the folder are copied.
Sub folders are not copied.
vFile1
<
•
If there is a file or folder with the same name, a message
is displayed. If you select "OK", a number is added as
"Name_001".
;
;
v
v
v
;
Folder4
•
If there is not enough space for the selected file or folder,
"OVER" is displayed. Reduce the number of files to copy
or erase unnecessary files in the USB memory.
If copying is canceled or if space runs out while copying,
the files copied up to that point remain.
The displayed space is a rough estimate. The actual size
may be smaller or greater.
Audio files with DRM can be copied, but cannot be
played.
Files cannot be copied from an iPod.
Depending on the digital audio player, it may not be
possible to copy files.
When files are copied from Music Editor media, the
copied audio files are played as normal audio file. Song
selection using the Music Editor media function is not
possible.
An empty folder cannot be
copied.
v
;
<
:
v
•
•
•
⁄
•
Read <About Internal Memory> (page 35) before
starting copy.
1 Connect the USB device to copy.
•
•
2 Enter Copy mode
Using the Control knob, select "COPY".
For the operation method, refer to <Function
Control mode> (page 11).
•
3 Select a file/folder to copy
Select the audio file or folder using the Control
knob.
Operation type
Operation
Movement between Turn the Control knob or push it towards up
items
or down.
Selection of item
Push the Control knob towards right.
Return to previous item Push the Control knob towards left.
Return to first item
Push the Control knob towards left for at least
1 second.
Confirm item
Press the Control knob.
4 Start copy
Select "OK" using the Control knob.
Number of files copied
"Completed" is displayed when copying completes.
Cancelling copy
1 Cancel copy
Press the [FNC] button.
Exits Copy mode if pressed by step 3.
2 Select "YES"
Select "YES" using the Control knob.
|
38
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting files in memory
Deleting audio files in memory.
⁄
•
Read <About Internal Memory> (page 35) before
starting to delete.
•
•
Deleted files and folder cannot be restored.
Use Format to delete all songs. Refer to <Internal
Memory Format> (page 53).
1 Select Internal Memory source
Press the [SRC] button.
Select the "Internal Memory" display.
Refer to <Selecting the Source> (page 8).
2 Enter Delete mode
Using the Control knob, select "DELETE".
For the operation method, refer to <Function
Control mode> (page 11).
3 Select a file/folder to delete
Select the audio file or folder using the Control
knob.
Operation type
Operation
Movement between Turn the Control knob or push it towards up
items
or down.
Selection of item
Push the Control knob towards right.
Return to previous item Push the Control knob towards left.
Return to first item
Push the Control knob towards left for at least
1 second.
Confirm item
Press the Control knob.
4 Start deleting
Select "OK" using the Control knob.
Number of files deleted
"Completed" is displayed when deleting completes.
Canceling delete
1 Cancel delete
Press the [FNC] button.
Exits Delete mode when pressed by step 3.
2 Select "YES"
Select "YES" using the Control knob.
5 Exit Delete mode.
Select "EXIT" using the Control knob.
Returns to step 3 if "NEXT" is selected.
English
|
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite Radio tuner control features
Control knob
FM
ꢁ
D
AM
FNC
SRC
AUTO
Band display
Channel number
Function icon
Select Satellite Radio Mode
Switching Seek Mode
Selecting the Satellite Radio Tuner (optional
accessory) connected to this unit.
Sets the seeking mode.
Press the [AUTO] button.
Each time you press the button, the Seek mode
alternates between the operations shown in the
table below.
Selecting Satellite Radio Mode
Press the [SRC] button.
Select the "SAT" display.
Display
"Seek : Channel"
"Seek : Preset"
Operation
Normal manual seeking control.
Search in order of the channels in the Preset
memory.
⁄
•
You need to register to the service provider to receive
the service by Satellite Radio. Consult the service
provider if "CALL TO SUBSCRIBE" appears.
•
•
The radio may take a little time to start receiving after
you select the Satellite Radio source.
If the signal reception fails, "Acquiring Signal" appears.
Select the channel
Selecting the channel.
Push the Control knob towards [4] or [¢].
|
40
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Category and Channel Search
Selecting the Preset Band
Selecting the channel and category you want to
receive.
Push the Control knob toward [FM].
Each time you push the knob, the preset band
alternates between the SR1, SR2, SR3 and SR4.
1 Enter Category and Channel Search mode
Press the Control knob.
2 Select the Category
Channel Preset Memory
Push the Control knob towards up or down.
⁄
Putting the channel in the memory.
•
It is the item when the category of 2nd text display part
is selected.
1 Select the preset band
Push the Control knob toward [FM].
3 Select the Channel
2 Select the channel to put in the memory
Push the Control knob towards [4] or [¢].
Push the Control knob towards [4] or [¢].
⁄
3 Enter Preset Memory mode
•
You cannot Channel search until the category
information is acquired.
Using the Control knob, select "P.MEMORY".
For the operation method, refer to <Function
Control mode> (page 11).
Cancelling Category and Channel Search mode
Press the Control knob.
4 Select the number to put in the memory
Turn the Control knob.
5 Determine the number to put in the memory
Function of remote control
Press the Control knob.
Direct Access Tuning
Entering the channel and tuning.
6 Allow the determined number to take effect
Press the Control knob.
1 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
Cancelling the Preset Memory mode
Press the [FNC] button.
⁄
2 Enter the channel
•
Only the channel number is stored. Category information
is not stored.
Press the number buttons.
3 Do Channel Search
Push the Control knob towards [4] or [¢].
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
⁄
•
If you make no button operation for 10 seconds, the
Direct Access Tuning mode is automatically canceled.
If you cannot receive any signal in the input Channel due
to bad conditions on radio wave or other such problems,
"Acquiring Signal" appears.
•
English
|
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite Radio tuner control features
Preset Tuning
Recalling the channels in the memory.
1 Select the preset band
Push the Control knob toward [FM].
2 Enter Preset Tuning Select mode
Turn the Control knob.
3 Select a desired station in the memory
Turn the Control knob.
4 Recall the station
Press the Control knob.
Cancelling Preset Tuning
Press the [FNC] button.
Channel Scan
Checks every receivable Channel for 10 seconds.
1 Start Channel Scan
Press the [AUTO] button for at least 2 seconds.
The channel number display blinks.
2 Release the button when the music you want
to hear is received
Press the [AUTO] button for at least 2 seconds.
Text Scroll for Satellite Radio source
Scrolls the displayed channel name and other items.
Push the Control knob toward up for at least 2
seconds.
⁄
•
When the <Display Illumination Control> (page 47) is set
to OFF, the display may black out while scrolling.
|
42
English
Download from Www.Somanuals.com. All Manuals Search And Download.
HD Radio control features
Control knob
FM
ꢁ
D
AM
FNC
SRC AUTO/AME
ST indicator
Band display
Preset station number
Frequency display
Function icon
About HD Radio
Tuning
Selecting the station.
•
When you connect an HD Radio, Tuner features
of the unit are disabled and changed to HD Radio
tuner features. A portion of the setting methods
including the Tuning Mode will change.
1 Select HD Radio source
Press the [SRC] button.
Select the "HD Radio" display.
•
With the HD Radio tuner, you can use the similar
functions to <Station Preset Memory>, <Auto
Memory Entry>, and <Preset Tuning> of Tuner
features. Refer to Tuner features for how to use
the functions.
2 Select the HD FM band
Push the Control knob toward [FM].
Each time you push the knob to [FM], the band
alternates between the HF1, HF2, and HF3 bands.
Select the HD AM band
Push the Control knob toward [AM].
3 Tune up or down band
Push the Control knob towards [4] or [¢].
English
|
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu system
Control knob
FNC
SRC
Function icon
You can continue by returning to step 2 and
setting other items.
Menu System
Setting beep sound during operation, etc.
functions.
The Menu system basic operation method is
explained here. The reference for the Menu items
and their setting content is after this operation
explanation.
4 Exit Menu mode
Press the [FNC] button.
⁄
•
When other items those applicable to the basic
operation method above are displayed, their setting
content chart is entered. (Normally the setting listed at
the top of the chart is the original setting.)
Also, the explanation for items that are not applicable
(<Manual Clock Adjustment> etc.) are entered step by
step.
1 Enter Menu mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 11).
2 Select the menu item
Turn the Control knob or push it towards up or
down.
Example: When you want to set the beep sound
select the "Beep" display.
3 Set the menu item
Push the Control knob towards right or left.
Example: When you select "Beep", each time you
push the knob it alternates between
"Beep : ON" or "Beep : OFF". Select 1 of
them as the setting.
|
44
English
Download from Www.Somanuals.com. All Manuals Search And Download.
In Standby mode
9 Exit Security Code mode
Press the [FNC] button.
Activating Security Code
Resetting the Security Code function when the
audio unit is first used after removed from the
battery power source or the Reset button is
pressed
Activating the Security Code disables the usage
of audio unit by someone else. Once the Security
Code is activated, the entry of authorized Security
Code is required to turn on the audio unit when it is
removed from the vehicle. Indication of this Security
Code activation prevents your precious audio unit
from stealing.
1 Turn the power ON.
2 Do the step 4 through 7 operation, and enter
the Security Code.
"Approved" is displayed.
Now, you can use the unit.
⁄
•
You can set the Security Code with a 4 digit number of your
choice.
⁄
•
The Security Code cannot be displayed or referenced. Make
a note of the Security Code and treasure it up.
•
When the Security Code function is activated, "Security
Set" changes to "Security Clear".
•
To deactivate the Security Code function, see the next
section <Deactivating Security Code>.
1 Enter Standby
Press the [SRC] button.
Select the "STANDBY" display.
Refer to <Selecting the Source> (page 8).
2 Enter Menu mode
In Standby mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 11).
Deactivating Security Code
To deactivate the Security Code function.
"Security Set" is displayed.
1 Select Security Code mode
Turn the Control knob.
Select the "Security Clear" display.
3 Enter Security Code mode
Press the Control knob for at least 1 second.
When "Enter" is displayed, "SECURITY SET" is also
displayed.
2 Enter Security Code mode
Press the Control knob for at least 1 second.
When "Enter" is displayed, "SECURITY CLEAR" is also
displayed.
4 Select the digits to enter
Push the Control knob towards right or left.
3 Select the digits to enter
5 Select the Security Code numbers
Turn the Control knob or push it towards up or
down.
Push the Control knob towards right or left.
4 Select the Security Code numbers
Turn the Control knob or push it towards up or
down.
6 Repeat steps 4 and 5, and complete the
Security Code.
5 Repeat steps 3 and 4, and complete the
7 Confirm the Security Code
Security Code.
Press the Control knob for at least 3 seconds.
When "Re-Enter" is displayed, "SECURITY SET" is also
displayed.
6 Press the Control knob for at least 3 seconds.
"Clear" is displayed.
The Security Code function deactivates.
8 Do the step 4 through 7 operation, and reenter
the Security Code.
"Approved" is displayed.
7 Exit Security Code mode
Press the [FNC] button.
The Security Code function activates.
⁄
⁄
•
If a wrong security code is entered, "Error" is displayed.
Enter a correct security code.
•
If you enter the wrong Code in steps 4 through 6, repeat
from step 4.
English
|
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu system
In Standby mode
3 Selecting the item (hours or minutes) to adjust
Push the Control knob towards right or left.
The items that are blinking are items that you can
adjust.
Source Select Mode
Setting up the Source Select mode.
Display
"SRC Select : 1"
"SRC Select : 2"
Setting
4 Adjust each item
Displays source icons for your choice.
Allows you to select sources one after another.
Turn the Control knob or push it towards up or
down.
5 Exit Clock adjustment mode
Press the [FNC] button.
In USB mode with iPod connected
iPod mode setting
In Standby mode
Setting up the iPod operation method in File Select.
Date Adjustment
Display
Setting
"iPod Mode : ON"
Uses the operation method similar to that of
iPod.
Uses the operation method different from that
of iPod.
1 Select Date Adjust mode
Turn the Control knob.
Select the "Date Adjust" display.
"iPod Mode : OFF"
2 Enter Date Adjust mode
Press the Control knob for at least 1 second.
The date display blinks.
In Standby mode
3 Selecting the item (day, month, or year) to
adjust
Touch Sensor Tone
Push the Control knob towards right or left.
The items that are blinking are items that you can
adjust.
Setting the operation check sound (beep sound)
ON/OFF.
Display
Setting
4 Adjust each item
"Beep : ON"
"Beep : OFF"
Beep is heard.
Beep canceled.
Turn the Control knob or push it towards up or
down.
5 Repeat step 3 and 4 operation and adjust the
date.
In Standby mode
6 Exit Date adjustment mode
Manual Clock Adjustment
Press the [FNC] button.
⁄
•
You can do this adjustment when the <Synchronize
Clock> (page 47) is set as OFF.
1 Select Clock Adjustment mode
Turn the Control knob.
Select the "Clock Adjust" display.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second.
The clock display blinks.
|
46
English
Download from Www.Somanuals.com. All Manuals Search And Download.
In Standby mode
Display Illumination Control
This function turns off the display when you
perform no operation for 5 seconds. This function is
effective when you are driving at night.
Date Mode
Setting the date format.
1 Select Date Mode
Display
Setting
Turn the Control knob.
Select the "Date Mode" display.
"Display : ON"
"Display : OFF"
Keeps the display on.
Turns off the display when you perform no
operation for 5 seconds.
2 Enter Date mode
Press the Control knob for at least 1 second.
⁄
3 Select the date format
Turn the Control knob or push it towards up or
down.
•
•
•
Set the Display Illumination Control when the
<Demonstration mode Setting> (page 53) is set to OFF.
When the display is off, pressing any key will turn on the
display.
When the display is off, you cannot perform any
operation except for the following:
4 Exit Date mode
Press the [FNC] button.
•
•
•
•
•
•
Volume
Attenuator
Selecting the source
Ejecting the disc
Turning off the power
USB remove mode
In Standby mode
Synchronize Clock
Synchronizing the RDS station time data and this
unit’s clock.
•
During function control, such as the Menu System, the
display stays on.
Display
"SYNC : OFF"
Setting
Adjust the time manually.
"SYNC : ON"
Synchronizes the time.
⁄
In Standby mode
•
It takes 3 to 4 minutes to synchronize the clock.
Dimmer
Dimming this unit’s display automatically when the
vehicle light switch is turned ON.
In Standby mode
DSI (Disabled System Indicator)
A red indicator will blink on the unit after the
faceplate is removed, warning potential thieves.
Display
Setting
"Dimmer : ON"
"Dimmer : OFF"
The display dims.
The display does not dim.
Display
Setting
"DSI : ON"
"DSI : OFF"
LED flashes.
LED OFF.
English
|
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu system
In Standby mode
Other than Standby mode/
When the Dual Zone System is ON
Contrast Adjustment
Adjusting the display contrast.
Dual Zone System Setting
Setting the Front channel and Rear channel sound
in the Dual Zone System.
Display and Setting
"Contrast : 1"
Display
Setting
"Zone 2 : Rear" Sub source (Auxiliary input source) is to be rear
channel.
"Contrast : 4" (Original setting)
"Zone 2 : Front" Sub source (Auxiliary input source) is to be front
channel.
In Standby mode
Display-reversing Setting
Other than Standby mode
If no operation is performed for a predetermined
period of time, switching between negative and
positive display modes takes place automatically.
Display-reversing maintains the initial brightness of
the display for a long period of time.
B.M.S. (Bass Management System)
Adjust the bass boost level of the external amplifier
using the main unit.
Display
Setting
Bass boost level is flat.
Bass boost level is low (+6dB).
Bass boost level is mid (+12dB).
Bass boost level is high (+18dB).
Display
"Display N/P : Auto"
"Display N/P : POSI"
Setting
Auto reverse display
Positive display only
"AMP Bass : Flat"
"AMP Bass : +6"
"AMP Bass : +12"
"AMP Bass : +18"
⁄
•
Switching between negative and positive display may
⁄
not take place depending on the displayed mode.
•
Refer to the catalog or instruction manual for power
amplifiers that can be controlled from this unit.
For amplifiers, there are the models you can set from Flat
to +18 dB, and the models you can set from Flat to +12
dB.
When an amplifier that can only be set to +12 is
connected to the unit, "AMP Bass : +18" will not work
correctly even if it is selected.
•
In Standby mode
Built-in Amp Setting
Controlling the built-in amplifier.
Turning OFF this control enhances the preout
quality.
Display
"AMP : ON"
"AMP : OFF"
Setting
The built-in amplifier activates.
The built-in amplifier deactivates.
Other than Standby mode
B.M.S. Frequency Offset
Setting the central frequency, boosted by B.M.S.
Display
Setting
"AMP FREQ : Normal"
"AMP FREQ : Low"
Boost with the normal central frequency.
Drop the normal central frequency 20%.
|
48
English
Download from Www.Somanuals.com. All Manuals Search And Download.
When LX AMP unit connecting
Other than Standby mode
AMP Control
Traffic Information
You can control the LX AMP connected to the unit.
Switching to traffic information automatically
when a traffic bulletin starts even when you are not
listening to the radio.
1 Select AMP Control mode
Turn the Control knob.
Select the "AMS Control" display.
Display
"TI : OFF"
"TI : ON"
Setting
The Traffic Information function is OFF.
The Traffic Information function is ON.
2 Enter AMP Control mode
Press the Control knob for at least 1 second.
When a traffic bulletin starts, "Traffic INFO" is
displayed it and it switches to traffic information.
3 Select the AMP Control item for adjustment
Push the Control knob towards up or down.
⁄
⁄
•
During reception of an AM station when the Traffic
Information function is turned ON, it switches to an FM
station.
•
For the details on the AMP Control item, see the
Instruction manual attached to the LX AMP.
•
During reception of traffic information the adjusted
volume is automatically remembered, and the next time
it switches to traffic information it’s automatically the
remembered volume.
4 Adjust the AMP Control item
Push the Control knob towards right or left.
5 Exit AMP Control mode
Press the [FNC] button.
Receiving other traffic information stations (In
tuner source)
Push the Control knob towards [4] or [¢].
⁄
•
⁄
•
You cannot use the LX AMP operation during standby
mode.
You can change the traffic information station when
listening to the radio.
In FM reception
CRSC (Clean Reception System Circuit)
Temporarily have reception alternate from stereo to
mono to reduce multi-path noise when listening to
the FM station.
Display
Setting
"CRSC : ON"
"CRSC : OFF"
The CRSC is ON.
The CRSC is OFF.
⁄
•
Strong electrical fields (such as from power lines) may
cause unstable sound quality when CRSC is turned ON.
In such a situation, turn it OFF.
English
|
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu system
In HD Radio mode
Auxiliary Input Display Setting &
Station/Disc Naming
Receive mode Setting
Sets the receive mode.
Selecting the display when changing to Auxiliary
input source. For the Station/Disc Naming refer to
the <Station/Disc Naming (SNPS/DNPS)> (page 24).
1 Select the Receive mode
Push the Control knob towards up or down.
Select the "Receive Mode" display.
1 Select Auxiliary input source
Press the [SRC] button.
Select the "AUX"/"AUX EXT" display.
2 Enter Receive mode
Press the Control knob for at least 1 second.
Refer to <Selecting the Source> (page 8).
3 Set the Receive mode
2 Enter Menu mode
Push the Control knob towards up or down.
Each time you push the knob, the Receive mode
alternates between the modes shown in the table
below.
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 11).
3 Select Auxiliary input display setting mode
Turn the Control knob.
Select the "Name Set" display.
Receive mode Display
Operation
Auto mode
"Auto"
Analog broadcasts and digital
broadcasts will be switched
automatically.
When both are being transmitted,
the digital broadcast will have
priority.
4 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The presently selected Auxiliary input display is
displayed.
Digital
Analog
"Digital"
"Analog"
Digital broadcasts only.
Analog broadcasts only.
5 Select the Auxiliary input display
Turn the Control knob or push it towards up or
4 Exit Receive mode
down.
Press the [FNC] button.
Each time you push the knob, the display alternates
⁄
as listed below.
• "AUX"/"AUX EXT"
• "DVD"
• "PORTABLE"
• "GAME"
•
Even if the Receive mode is set to "Auto", when the Ball
game mode program (non-delayed broadcast program)
is received, the Receive mode will automatically switch
to Analog broadcast only.
• "VIDEO"
• "TV"
In Satellite radio source
Electronic Serial Number (ESN)
display
6 Exit Auxiliary input display setting mode
Press the [FNC] button.
⁄
•
When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.
Displaying the Electronic Serial Number.
Display
"ESN=************"
•
The Auxiliary input display can be set only when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used.
⁄
•
Electronic Serial Number (ESN)
It is important to retain the unit serial number and the
electronic Satellite radio Identification number for service
activation and potential service changes.
|
50
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Text Scroll
Setting the displayed text scroll.
Display
Setting
"Scroll : Auto"
"Scroll : Manual"
Repeats scroll.
Scrolls when the display changes.
⁄
•
The text scrolled is listed below.
- CD text
- Folder name/ File name/ Music title/ Artist name/
Album name
- MD title
- Radio text
- Text for the Satellite radio source, HD Radio source,
including Channel name, etc.
In Standby mode
Built-in Auxiliary input Setting
Set the Built-in Auxiliary Input function.
Display
Setting
"Built in AUX : OFF" When selecting the source there’s no Auxiliary Input.
"Built in AUX : ON" When selecting the source there’s Auxiliary Input.
In Standby mode
CD Read Setting
When there is a problem with playing a CD with
special format, this setting plays the CD by force.
Display
Setting
"CD Read : 1"
"CD Read : 2"
Play CD and Audio file.
Play CD by force.
⁄
•
Some music CDs may not play even in the "CD Read : 2"
mode.
English
|
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu system
In Standby mode
Cancelling Downloading
Press the [FNC] button.
Picture downloading
8 Exit the downloading mode
Downloading wallpapers. You can use downloaded
pictures for the display of this unit.
Press the [FNC] button.
⁄
1 Connected the USB device or Insert a CD-R/
CD-RW
Connect the USB device containing the files to be
•
•
•
Do not operate this unit while downloading to prevent
data from being damaged.
The number of files that can be downloaded.
- Wallpaper: 1 file
downloaded into this unit.
Or with the USB device removed, insert a CD-R/CD-
RW containing files to be downloaded into this
unit.
Refer to <Playing CD & Audio file> (page 30) for
details.
When a new wallpaper is downloaded, it is overwritten
to the currently downloaded wallpaper.
There is no way to delete the downloaded pictures.
The downloaded pictures can be used for display.
<Graphic Display Selection> (page 17)
When you cannot download the pictures to this unit,
there may be a problem with the CD-R/CD-RW/USB
device write method.
•
•
⁄
•
how to make CD-R/CD-RW/USB device.
2 Enter Standby
PICTURE ENGINE
Press the [SRC] button.
Picture Engine is an application software
distributed from Kenwood's official website.
Utilizing this software, you can create an original
still image file. As for the download of application,
please browse "http://www.kenwood.net-disp.
com/" for directions.
Select the "STANDBY" display.
Refer to <Selecting the Source> (page 8).
3 Enter Menu mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 11).
4 Select the picture downloading
Turn the Control knob.
Select the "DISP Data DL" display.
5 Enter the downloading mode
Press the Control knob for at least 1 second.
"File Check!!" display blinks.
6 Select files to be downloaded
Turn the Control knob or push it towards up or
down.
Press the Control knob.
7 Start downloading
Select "YES" using the Control knob.
When the downloading finishes, "Finished" is
displayed.
⁄
•
Picture downloading may take as long as 20 minutes.
Quantity
|
52
English
Download from Www.Somanuals.com. All Manuals Search And Download.
In Standby mode
In Standby mode
Firmware version display
Demonstration mode setting
Displaying the firmware version with the unit.
Sets the demonstration mode.
Turn the Control knob.
Select the "F/W Version : " display.
1 Select the Demonstration mode
Turn the Control knob.
Select the "DEMO Mode" display.
2 Set the Demonstration mode
In Internal Memory source
Press the Control knob for at least 2 seconds.
Each time you press the knob at least 2 seconds,
the Demonstration mode alternates between the
settings shown in the table below.
Internal Memory Format
Perform format to delete all audio files stored in
internal memory.
Display
Setting
⁄
"DEMO Mode : ON"
The Demonstration mode function is ON.
•
The content of formatted memory cannot be restored.
Be careful when formatting.
"DEMO Mode : OFF" Exit Demonstration mode (Normal mode).
1 Enter Internal Memory
Press the [SRC] button.
Select the "Internal Memory" display.
2 Enter Menu mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 11).
3 Select the Internal Memory Format
Turn the Control knob.
Select the "INT.MEM.Format" display.
4 Enter the Formatting mode
Press the Control knob for at least 1 second.
"Format?" is displayed.
5 Start format
Select "YES" using the Control knob.
"Format..." display blinks.
When the formatting finishes, "Completed" is
displayed.
6 Exit Formatting mode
Press the [FNC] button.
English
|
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations of remote control
SRC
ATT
VOL
SRC
AT T
VOL
AUD
AUD
FM/AM/+/–
2-ZONE
DIRECT
[0] — [9]
: This button is used when Kenwood Bluetooth
HANDS FREE BOX is connected. For more
information, refer to the instruction manual of
Bluetooth HANDS FREE BOX.
Loading and Replacing the battery
Basic operations
Use two "AA"/ "R6"-size batteries.
Slide the cover while pressing downwards to
remove it as illustrated.
Insert the batteries with the + and – poles aligned
properly, following the illustration inside the case.
[VOL] buttons
Adjusts the volume.
[SRC] button
Each time you press the button, the source
alternates.
For the source alternating order refer to <Selecting
the Source> (page 8).
[ATT] button
Turns the volume down quickly.
When the button is pressed again, the volume
returns to the previous level.
2WARNING
•
Store unused batteries out of the reach of children.
Contact a doctor immediately if the battery is
accidentally swallowed.
¤
•
Do not set the remote control in hot places such as on
the dashboard.
|
54
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Control
In Disc/USB (iPod)/Internal Memory
source
[AUD] button
Selects the Audio item to be adjusted.
[4]/ [¢] buttons
Going forwards and backwards between music.
[VOL] buttons
Adjusts the Audio item.
[+]/ [–] buttons
Going forwards and backwards between disc/
folders.
⁄
•
Refer to <Audio Control> (page 9) for the operation
method, such as the procedures for Audio control and
others operations.
[38] button
Each time you press the button, the music is played
or paused.
[0] — [9] buttons
Dual Zone System
When in <Direct Music Search> (page 32) and
<Direct Disc Search> (page 32), enters the music/
disc number.
[2-ZONE] button
Each time you press the button, "2 ZONE" of
<Audio Setup> (page 10) is turned ON or OFF.
[5]/ [∞] buttons
In Satellite radio source
Adjusts the volume of the rear channel.
The rear channel activates while the Dual Zone
System is ON.
[FM] button
Selects the preset band.
[4]/ [¢] buttons
Searches up or down channels.
[0] — [9] buttons
Press buttons [1] — [6] to recall preset channels.
In Tuner source
[FM]/ [AM] buttons
Selects the band.
Each time you press the [FM] button, the band
alternates between the FM1, FM2, and FM3 bands.
[DIRECT] button
Enters and cancels the <Direct Access Tuning>
(page 41) mode.
[4]/ [¢] buttons
Tune up or down band.
In HD Radio source
[0] — [9] buttons
Press buttons [1] — [6] to recall preset stations.
[FM] button
Selects the HD FM band.
Each time you press the [FM] button, the band
alternates between the HF1, HF2, and HF3 bands.
[DIRECT] button
Enters and cancels the <Direct Access Tuning>
(page 27) mode.
[AM] button
Selects the HD AM band.
[38] button
Enters and cancels the <PTY (Program Type)>
(page 28) mode.
[4]/ [¢] buttons
Tunes up or down bands.
[0] — [9] buttons
Press buttons [1] — [6] to recall preset stations.
English
|
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories/ Installation Procedure
Accessories
¤
•
If the power is not turned ON ("Protect" is displayed), the
speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
1
..........1
•
2
•
•
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
..........2
3
•
•
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
..........4
4
..........4
•
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
5
..........1
•
•
Installation Procedure
If You Want to Connect iPod
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
iPod
AUDIO OUT
KCA-iP200 (Optional accessory)
•
•
No other optional accessory can be connected because
the USB connector and the AUX input are used for iPod
connection.
8. Press the reset button.
Dual Zone System in <Audio Setup> (page 10) will become
unavailable.
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
|
56
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Wires to Terminals
Tape
Front right output (Red)
Front left output (White)
FRONT
REAR
To USB device
Rear right output (Red)
Rear left output (White)
USB connector (1 m)
To use the steering wheel
⁄
remote control feature,
you need to an exclusive
remote adapter (not
supplied) matches your car
is required.
• Do not remove the cap when you
do not use the USB cable. The
connector will cause the unit to
malfunction if it gets in touch with
any metallic part of the vehicle.
• Fasten the connector with the
tape so that the cable will not
come off.
Sub Woofer right output (Red)
Sub Woofer left output (White)
SUB
WOOFER
FM/AM antenna input
REMO.CONT
Steering remote control
(Light Blue/Yellow)
To Kenwood disc changer/ External optional accessory
To connect these leads, refer to the relevant
⁄
instruction manuals.
AUX input (Stereo)
Use the mini-plug which is stereo type and does not
have any resistance.
Fuse (10A)
Wiring harness (Accessory1)
White/Black
White
To front left speaker
Gray/Black
To front right speaker
To rear left speaker
To rear right speaker
Gray
Green/Black
Green
Purple/Black
Purple
If no connections are made, do not let the wire come out from the tab.
When using the optional power amplifier, connect to its power control
terminal.
P.CONT
Power control wire (Blue/White)
Motor antenna control wire (Blue)
Depending on what antenna you are using, connect either to the
control terminal of the motor antenna, or to the power terminal for the
booster amplifier of the film-type antenna.
ANT.
CONT
Connect to the terminal that is grounded when either the telephone
rings or during conversation.
MUTE
TEL mute wire (Brown)
To connect the Kenwood navigation system, consult your
navigation manual.
⁄
To "EXT.AMP.CONT." terminal of the amplifier having the external amp
control function.
External amplifier control wire
(Pink/Black)
To car light control switch
Dimmer control wire (Orange / White)
Ignition key switch
Car fuse box
ACC
Ignition wire (Red)
Car fuse box (Main fuse)
Battery
Battery wire (Yellow)
Ground wire (Black) - (To car chassis)
+
–
|
English
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
non-Japanese cars
Japanese cars
1 Refer to the section <Removing the hard rubber
Metal mounting strap
(commercially available)
frame> and then remove the hard rubber frame.
2 Align the holes in the unit (two locations on each
side) with the vehicle mounting bracket and secure
the unit with the accessory screws.
Firewall or metal support
T
N
T/N
T
N
T: Toyota cars
N: Nissan cars
Bend the tabs of the
mounting sleeve with a
screwdriver or similar utensil
and attach it in place.
8 mm
MAX.
8 mm
MAX.
Self-tapping screw
(commercially available)
3
4
M5mm
M5mm
Accessory3...for Nissan car
Accessory4...for Toyota car
Screw (M4X8)
(commercially available)
¤
⁄
•
During installation, do not use any screws except for
those provided. The use of different screws might result in
damage to the main unit.
•
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
•
Damage may occur if a screwdriver or similar tool is used
with excessive force during the installations.
|
58
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the hard rubber frame
Screwing the Faceplate on the Unit
If you want to fasten the faceplate to the main unit
so that it does not fall off, screw in the provided
screws in the holes shown below.
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
Bottom panel
Lock
Accessory5
Catch
Accessory2
Removal tool
2 When the upper level is removed, remove the
lower two locations.
¤
•
⁄
Never insert the screw in any other screw hole than the one
specified. If you screw them in another hole, it will contact
and may cause damage to the mechanical parts inside the
unit.
•
The frame can be removed from the bottom side in the
same manner.
Removing the Unit
1 Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
2 Remove the screw (M4 × 8) on the back panel.
3 Insert the two removal tools deeply into the slots
on each side, as shown.
4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
Screw (M4X8)
(commercially available)
Accessory2
¤
•
Be careful to avoid injury from the catch pins on the
removal tool.
5 Pull the unit all the way out with your hands, being
careful not to drop it.
|
English
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
!
!
Cannot set up the Dual zone function.
In the speaker select option, None is selected for
the rear speakers. ☞ <Sound Management system>
(page 12)
!
Cannot switch to Aux source.
• AUX is not turned on. ☞ <Built-in Auxiliary input
Setting> (page 51)
• Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
The Dual zone function is disabled. ☞ <Audio
Setup> (page 10)
• AUX cannot be used when the KCA-iP200 is
connected.
!
!
• Cannot set up the Fader.
• No Audio control effect on AUX.
The Dual zone function is enabled. ☞ <Audio
Setup> (page 10)
!
• Cannot register a security code.
• Cannot set up Display Illumination Control.
<Demonstration mode Setting> (page 53) is not
turned off.
• Cannot set up the equalizer.
• Cannot set up WOW HD.
!
!
Cannot play audio files.
<CD Read Setting> (page 51) is set to "2".
• Cannot set up the crossover network.
• Cannot set up Digital Time Alignment.
• Cannot preset the sound system.
• The Dual zone function is enabled. ☞ <Audio
Setup> (page 10)
• In the speaker select option, None is selected for
the related speakers. ☞ <Sound Management
system> (page 12)
• Cannot File select.
• Cannot direct music search.
The Random play function is enabled.
!
• The Traffic Information setting is ineffective.
• The Synchronize Clock setting is ineffective.
HD Radio is in use.
!
!
• Cannot set up the subwoofer.
• Cannot set up subwoofer phase.
• No output from the subwoofer.
• In the speaker select option, None is selected for
the related speakers. ☞ <Sound Management
system> (page 12)
• <Subwoofer Output> (page 10) is not set to On.
• The Dual zone function is enabled. ☞ <Audio
Setup> (page 10)
• Cannot set up the sound management system.
• Cannot set up the position.
The Dual zone function is enabled. ☞ <Audio
Setup> (page 10)
!
!
Cannot set up SRS 3D Space Control or SRS 3D
Center Control.
The tuner or HD Radio source is in use.
Cannot set up the SRS 3D Center Control.
SRS 3D Space control is set to OFF. ☞ <WOW HD
Control> (page 14)
|
60
English
Download from Www.Somanuals.com. All Manuals Search And Download.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
HD Radio source
? No sound can be heard, or the volume is low.
✔
The preset broadcast station is not transmitting in
the mode that was set with <Receive mode Setting>
(page 50).
☞
Please set <Receive mode Setting> to "Auto".
General
✔
In digital AM broadcasting, receive mode switches
between stereo and monaural too often.
☞
? The Touch Sensor Tone does not sound.
Receiving condition is bad or unstable. Stereo is
chosen when receiving condition is good, and
it switches to monaural when the condition
becomes bad.
✔
The preout jack is being used.
☞
The Touch Sensor Tone cannot be output from
the preout jack.
? Switching between negative and positive display
modes takes place automatically.
✔
HD Radio tuner is connected to KCA-S220A or other
units.
☞
✔
Switching between negative and positive display
modes takes place automatically to maintain the
initial brightness of the display for a long period of
time.
Connect the HD Radio tuner directly to this unit.
USB device source
☞
You can select "Display N/P: POSI" as mentioned
in <Display-reversing Setting> (page 48).
? The USB device is not detected.
✔
The USB connector is disconnected.
☞
Connect the connector of the USB device
properly.
Tuner source
? The USB device does not play its audio files.
The USB connector is disconnected.
? Radio reception is poor.
✔
✔
✔
The car antenna is not extended.
☞
Connect the connector of the USB device
properly.
☞
Pull the antenna out all the way.
The antenna control wire is not connected.
☞
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>.
? Cannot USB remove mode.
Downloading picture.
✔
☞
USB remove mode is disabled while
downloading picture.
Disc source
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
Clean the CD.
The disc is loaded in a different slot from that
specified.
☞
☞
Eject the disc magazine and check the number
for the specified disc.
✔
The disc is severely scratched.
Try another disc instead.
☞
? Cannot remove disc.
Downloading picture.
Eject is disabled while downloading picture.
✔
☞
Audio file source
? The sound skips when an Audio file is being
played.
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 6).
✔
✔
The audio file is broken or not supported.
Damaged and unsupported files are skipped.
The recording condition is bad.
Record the media again or use another media.
☞
☞
|
English
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Hold Error:
The protective circuit in the unit activates
when the temperature inside the automatic
disc changer exceeds 60°C (140°F), stopping
all operation.
➪ Cool down the unit by opening the
windows or turning on the air conditioner.
As the temperature falls below 60°C
(140°F), the disc will start playing again.
The messages shown below display your
systems condition.
Eject:
• No disc magazine has been loaded in
the changer. The disc magazine is not
completely loaded.
• No CD in the unit.
No Disc:
No disc has been loaded in the disc
magazine.
No Name:
Waiting:
Attempted to display DNPS during the CD
play having no disc names preset.
TOC Error:
• No disc has been loaded in the disc
magazine.
• Radio text data is being received. Radio text
plus requires more time to load than radio
text.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
• Text for the Satellite Radio tuner source is
being received.
Read Error:
• The number of files or folders which are
stored in the connected USB device is above
the limitation.
• The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
kenwood.com/usb/. If the error message is
still displayed, initialize the USB device or
use other USB devices.
Load:
Discs are being exchanged in the Disc
changer.
Checking:
Reading:
The unit is reading the data on the disc, USB
device or Internal Memory.
IN (Blink):
Protect:
The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
Error 05:
The disc is unreadable.
Blank Disc:
No Track:
Nothing has been recorded on the MD.
No tracks are recorded on the MD, although it
has a title.
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable properly
and press the reset button. If the "Protect"
code does not disappear, consult your
nearest service center.
No Panel:
Error 77:
The faceplate of the slave unit being
connected to this unit has been removed.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
"Error 77" code does not disappear, consult
your nearest service center.
Unsupported File:
An Audio file is played with a format that this
Mecha Error: Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
➪ Check the disc magazine. And then press
the reset button on the unit. If the "Mecha
Error" code does not disappear, consult
unit cannot support.
Copy Protection:
A copy-protected file is played.
your nearest service center.
DEMO MODE: The Demonstration mode has been selected.
➪ The <Demonstration mode Setting> (page
53) is ON. Turn it OFF.
|
62
English
Download from Www.Somanuals.com. All Manuals Search And Download.
No Device:
N/A Device:
The USB device is selected as a source
although no USB device is connected.
Can’t Download:
Download Error:
This unit does not work properly for some
reason.
➪ Press the reset button to download it
again. If this error is still displayed, consult
a local Kenwood dealer.
➪ Try all over again from the start. If this error
is still displayed, consult a local Kenwood
dealer.
An unsupported USB device is connected.
➪ For the supported USB devices, refer to
<http://www.kenwood.com/usb/>.
No Music Data/ Error 15:
• The connected USB device contains no
playable audio file.
• The Internal Memory source contains no
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
No Display File:
No file that can be downloaded is contained
in the CD-R/ CD-RW/ USB device.
➪ Make sure that a files created with
disp.com> is contained in the CD-R/ CD-
RW/ USB device.
USB ERROR:
The connected USB device is rated a current
capacity higher than the allowable limit.
➪ Check the USB device with reference to
<http://www.kenwood.com/usb/>.
Some trouble may have occurred to the
connected USB device.
Do not delete the extension (.kbm)
created when the file was created.
➪ Change the source to any source other
than USB. Remove the USB device.
Incorrect File: The file selected to be downloaded has a
format that this unit cannot read.
➪ Recreate the file.
iPod Error:
Connection to the iPod has failed.
➪ Remove the USB device and then
reconnect it.
➪ Confirm that the software for the iPod is
the latest version.
Writing Error: Writing failed while the file was downloaded.
➪ Try the downloading again.
USB REMOVE: The Remove mode has been selected for the
USB device. You can remove the USB device
safely.
Over Capacity: Recording or copying was canceled because
internal memory space ran out while
recording from music CD or copying from
USB device.
➪ Delete unnecessary files and record or
copy once more.
Name Exists. Raname... :
Name Exists. Auto Rename? :
The name entered while recording CD
already exists. Or a file or folder with the same
name already exists while copying from USB
device.
➪ Change the name or delete the existing
file and record or copy once more.
Import Error: Recording is canceled because there is a
scratch on the CD and it cannot be played.
Copy Error:
• An incompatible digital audio player was
used.
• Cannot copy because the USB device is not
firmly inserted.
Delete Error:
Format Error: Abnormal condition detected while deleting
or formatting.
➪ Repeat the operation once more. This may
take some time. If the message recurs,
contact your nearest Kenwood dealer.
|
English
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications subject to change without notice.
FM tuner section
USB Interface
Frequency range (200 kHz space)
: 87.9 MHz – 107.9 MHz
USB Standard
: USB 1.1/ 2.0
Usable sensitivity (S/N = 30dB)
: 9.3dBf (0.8 μV/75 Ω)
Quieting Sensitivity (S/N = 50dB)
: 15.2dBf (1.6 μV/75 Ω)
Maximum Supply current
: 500 mA
File System
: FAT16/ 32
Frequency response ( 3 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
: 70 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
Selectivity ( 400 kHz)
: ≥ 80 dB
Stereo separation (1 kHz)
: 40 dB
AAC decode
: AAC-LC ".m4a" files
WAV decode
: Linear-PCM
AM tuner section
Audio section
Frequency range (10 kHz space)
: 530 kHz – 1700 kHz
Maximum output power
: 50 W x 4
Usable sensitivity (S/N = 20dB)
: 28 dBμ (25 μV)
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
Speaker Impedance
: 4 – 8 Ω
CD player section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 1 Bit
Spindle speed (Audio file)
: 1000 – 400 rpm (CLV 2times)
Wow & Flutter
: Below Measurable Limit
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
: 0.008 %
Tone action
Band 1 : 60 – 200 Hz 9 dB
Band 2 : 250 – 1k Hz 9 dB
Band 3 : 1.25k – 4k Hz 9 dB
Band 4 : 5k – 16k Hz 9 dB
Preout level / Load (during disc play)
: 5000 mV/10 kΩ
Preout impedance
: ≤ 80 Ω
Auxiliary input
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 100 kΩ
Signal to Noise ratio (1 kHz)
: 110 dB
Dynamic range
: 93 dB
MP3 decode
General
: Compliant with MPEG-1/2 Audio Layer-3
Operating voltage (11 – 16V allowable)
: 14.4 V
Current consumption
: 10 A
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC ".m4a" files
WAV decode
: Linear-PCM
Installation Size (W x H x D)
: 182 x 53 x 155 mm
7-3/16 x 2-1/16 x 6-1/8 inch
Weight
: 3.31 lbs (1.5 kg)
|
64
English
Download from Www.Somanuals.com. All Manuals Search And Download.
|