Kenwood CD Player KDC 5020 User Manual

CD-RECEIVER

KDC-MPV7020

KDC-6020

INSTRUCTION MANUAL

KDC-5020

KDC-5020R

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

IMPORTANT INFORMATION

About the disc changer/CD player to

be connected:

2WARNING

2CAUTION

To prevent injury or fire, take the

following precautions:

• Insert the unit all the way in until it is fully

locked in place. Otherwise it may fall out of

place when jolted.

• When extending the ignition, battery, or

ground wires, make sure to use automotive-

grade wires or other wires with a 0.75mm

(AWG18) or more to prevent wire

deterioration and damage to the wire

coating.

• To prevent a short circuit, never put or leave

any metallic objects (such as coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

To prevent damage to the machine,

take the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision

equipment.

To connect a disc changer having the "O-N"

switch to this unit, set the "O-N" switch to "N".

To connect a disc changer having no "O-N"

switch to this unit, the converter cord CA-

DS100 and/or switching adapter KCA-S210A

are required as options.

A disc changer doesn't work when it is

connected without using these options.

If a model with no "O-N" switch is connected,

some unavailable functions and information

that cannot be displayed are generated.

Note that none of the KDC-C100, KDC-C302,

C205, C705, and non-Kenwood CD changers

can be connected.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

You can damage both your unit and the CD

changer if you connect them incorrectly.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• Be careful not to drop the unit or subject it to

strong shock.

The unit may break or crack because it

contains glass parts.

• Do not touch the liquid crystal fluid if the

LCD is damaged or broken due to shock. The

liquid crystal fluid may be dangerous to your

health or even fatal.

• To prevent a short circuit when replacing a

fuse, first disconnect the wiring harness.

• Do not place any object between the

faceplate and the unit.

• Do not use your own screws. Use only the

screws provided. If you use the wrong

screws, you could damage the unit.

• Do not apply excessive force to the open

faceplate or place objects on it. Doing so will

cause damage or breakdown.

The marking of products using lasers

(Except for some areas)

CLASS 1

LASER PRODUCT

The label is attached to the chassis/case and

says that the component uses laser beams

that have been classified as Class 1. It

means that the unit is utilizing laser beams

that are of a weaker class. There is no

danger of hazardous radiation outside the

unit.

If the liquid crystal fluid from the LCD

contacts your body or clothing, wash it off

with soap immediately.

Do Not Load 3-in. CDs in the CD slot

If you try to load a 3 in. CD with its adapter

into the unit, the adapter might separate from

the CD and damage the unit.

— 3 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

About RDS

Lens Fogging

RDS (Radio Data System)

NOTE

Right after you turn on the car heater in cold

weather, dew or condensation may form on

the lens in the CD player of the unit. Called

lens fogging, CDs may be impossible to play.

In such a situation, remove the disc and wait

for the condensation to evaporate. If the unit

still does not operate normally after a while,

consult your Kenwood dealer.

When listening to an RDS station, the

programme service name of the station is

displayed, advising you quickly which station is

being received.

• If you experience problems during

installation, consult your Kenwood dealer.

• If the unit fails to operate properly, press the

Reset button. The unit returns to factory

settings when the Reset button is pressed.

If the unit still fails to operate properly after

the Reset button has been pressed, contact

your local KENWOOD dealer for assistance.

• Press the reset button if the disc auto

changer fails to operate correctly. Normal

operation should be restored.

RDS (Radio Data System) stations also

transmit frequency data for the same station.

When you are making long trips, this function

automatically alternative switches to the

particular frequency with the best reception

for the particular network of stations that you

want to listen to. The data is automatically

stored, allowing you to switch quickly to

another RDS stations, broadcasting the same

programme, that has better reception. These

include stations stored in the station preset

memory that you often listen to.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get

dirty, wipe them with a dry, soft cloth.

Cleaning the Unit

OFF

If the faceplate of this unit is stained, wipe it

with a dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the stain

off with a cloth moistened with neutral

cleaner, then wipe neutral detergent off.

DAB

PTY MENU

SCAN

RDM

REP

M.RDM

DISP NAME TI GSM

AUD

Enhanced Other Network

LOUD

Stations that offer <Enhanced Other

Network> also transmit information about

other RDS stations that have traffic

information. When you are tuned to a station

that is not transmitting traffic information, but

another RDS station starts transmitting a

traffic bulletin, the tuner automatically

switches to the other station for the duration

of the bulletin.

Applying spray cleaner directly to the unit may

affect its mechanical parts. Wiping the

faceplate with a hard cloth or using a volatile

liquid such as thinner or alcohol may scratch

the surface or erases characters.

Reset button

• We recommend the use of the Security

Code function (see p. 24) to prevent theft.

• Characters in the LCD may become difficult

to read in temperatures below 41 ˚F (5 ˚C).

• The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the display

in the illustrations may differ from what

appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

Cleaning the CD Slot

As dust tends to accumulate in the CD slot,

clean it every once in a while. Your CDs can

get scratched if you put them in a dusty CD

slot.

Alarm

When an emergency transmission (announcing

disasters, etc.) is sent, all current functions are

interrupted to allow the warning to be

received.

— 4 —

Download from Www.Somanuals.com. All Manuals Search And Download.

About CDs

Handling CDs

• Don’t touch the recording surface of the CD.

CD cleaning

Clean from the center of the disc and move

outward.

Removing CDs

When removing CDs from this unit pull them

• CD-R and CD-RW are easier to damage than

a normal music CD. Use a CD-R or a CD-RW

after reading the caution items on the

package etc.

• Don’t stick tape etc. on the CD.

Also, don’t use a CD with tape stuck on it.

out horizontally.

CDs that can’t be used

• CDs that aren’t round can’t be used.

When using a new CD

If the CD center hole or outside rim has burrs,

use it after removing them with a ball pen etc.

• CDs with coloring on the recording surface

or that are dirty can’t be used.

• Don’t use CDs without disc mark

Burrs

• A CD-R or CD-RW that hasn’t been finalized

can’t be played. (For the finalization process

refer to your CD-R/CD-RW writing software,

and your CD-R/CD-RW recorder instruction

manual.)

Burrs

CD storage

• Don’t place them in direct sunlight (On the

seat or dashboard etc.) and where the

temperature is high.

CD accessories

Don’t use disc type accessories.

• Store CDs in their cases.

— 5 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on playing MP3

This unit can play MP3(MPEG1, 2, 2.5 Audio Layer 3). Note,

however, that the MP3 recording media and formats acceptable

are limited. When writing MP3, pay attention to the following

restrictions.

Entering ID3 tag

The Displayable ID3 tag is ID3 version

1.x.

For the character code, refer to the

List of Codes.

Acceptable media

The MP3 recording media acceptable to this unit are CD-ROM, CD-R,

Entering file and folder names

and CD-RW.

The code list characters are the only

When using CD-RW, do full format not quick format to prevent

malfunction.

file names and folder names that can

be entered and displayed.

If you use any other character for

Acceptable medium formats

entry, the file and folder names are not displayed correctly. They may

neither be displayed correctly depending on the CD writer used.

The unit recognizes and plays only those MP3 which have the MP3

extension (.MP3).

The following formats are available for the media used in this unit. The

maximum number of characters used for file name including the

delimiter (".") and three-character extension are indicated in

parentheses.

• ISO 9660 Level 1 (12 characters)

• ISO 9660 Level 2 (31 characters)

A file with a name entered with characters not on the code list may not

play correctly.

• Joliet (64 characters)

• Romeo (128 characters)

Up to 200 characters can be displayed in the long file name format.

For a list of available characters, see the instruction manual of the

writing software and the section Entering file and folder names below.

The media reproducible on this unit has the following limitations:

• Maximum number of directory levels: 8

• Maximum number of files per folder: 255

• Maximum number of characters for folder name: 64

• Maximum number of folders: 50

Writing files into a medium

When a medium containing MP3 data is loaded, the unit checks all the

data on the medium. If the medium contains a lot of folders or non-

MP3 files, therefore, it takes a long time until the unit starts playing

MP3.

In addition, it may take time for the unit to move to the next MP3 file

or a Track Search or Album Search may not be performed smoothly.

Loading such a medium may produce loud noise to damage the speakers.

• Do no attempt to play a medium containing a non-MP3 file with the

MP3 extension.

MP3 written in the formats other than the above may not be

successfully played and their file names or folder names are not

properly displayed.

The unit mistakes non-MP3 files for MP3 data as long as they have

the MP3 extension.

• Do not attempt to play a medium containing non MP3.

Settings for your MP3 encoder and CD writer

When you use your CD writer to record MP3 up to the maximum disc

capacity, disable additional writing. For recording on an empty disc up

to the maximum capacity at once, check Disc at Once.

— 6 —

Download from Www.Somanuals.com. All Manuals Search And Download.

MP3 playing order

When a Track Search is executed with file ¡$ being played ...

When selected for play, Album Search, Track Search, or for Album

Select, files and folders are accessed in the order in which they were

written by the CD writer.

Operation of the button

¢ Button

Current

file number

4 Button

Beginning of file

Because of this, the order in which they are expected to be played

may not match the order in which they are actually played. You may be

able to set the order in which MP3 are to be played by writing them

onto a medium such as a CD-R with their file names beginning with

play sequence numbers such as "01" to "99", depending on your CD

writer.

When an Album Search is executed with file ¡$ being played ...

Operation of the button

Current

folder number

AM Button

FM Button

For example, a medium with the following folder/ file hierarchy is

subject to Album Search, Track Search, or Album Select as shown

below.

Example of a medium's folder/file hierarchy

When Album Select is selected with file ¡$ being played to move

from folder to folder ...

Operation of the button

Current

folder number

4 Button

¢ Button

AM Button

FM Button

Folder

File

Root

Level 1

Level 3

Level 2

Level 4

— 7 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Release button

u / d

SRC FM FM

Power

Turning ON the Power

OFF

DAB

Press the [SRC] button.

When the power is ON, the <Security Code> (page 24) is displayed

as "CODE ON" or "CODE OFF".

SCAN

RDM

REP

M.RDM

DISP NAME AUTO GSM

Turning OFF the Power

AUD

Press the [SRC] button for at least 1 second.

LOUD

AM /

ATT /

LOUD

AUD

DISP/NAME

Selecting the Source

Press the [SRC] button.

KDC-MPV7020/6020

Source required

Display

ATT indicator

Tuner

"TUNER"

"CD"

External disc

Auxiliary input

"DISC-CH"/"CD2"

"AUX"

Standby (Illumination only mode)

"ALL OFF"

For Auxiliary input one of the below optional accessories is

necessary.

- KCA-S210A

Speaker Setting indicator

- CA-C1AX

SYSTEM Q indicator

- CD changer with an Auxiliary input function installed.

KDC--5020/5020R

ATT indicator

Volume

Increasing Volume

Press the [u] button.

Decreasing Volume

Press the [d] button.

Speaker Setting indicator

SYSTEM Q indicator

Download from Www.Somanuals.com. All Manuals Search And Download.

— 8 —

• User memory: The values set on the <Audio control> (page 9).

• Each setting value is changed with the <Speaker setting> (page

10).

Attenuator

Turning the volume down quickly.

First, select the speaker type with the Speaker setting.

Press the [ATT] button.

Each time the button is pressed the Attenuator turns ON or OFF.

When it’s ON, the "ATT" indicator blinks.

Audio Control

1 Select the source for adjustment

Press the [SRC] button.

Loudness

Compensating for low and high tones during low volume.

2 Enter Audio Control mode

Press the [LOUD] button for at least 1 second.

Each time the button is pressed for at least 1 second the

Loudness turns ON or OFF.

Press the [AUD] button for at least 1 second.

3 Select the Audio item for adjustment

Press the [FM] or [AM] button.

When it's ON, "LOUD ON" is displayed.

Each time the button is pressed the items that can be adjusted

switch as shown below.

System Q

4 Adjust the Audio item

Press the [4] or [¢] button.

You can recall the best sound setting preset for different types of

the music.

Adjustment Item

Display

Range

1 Select the source to set

Bass level

Middle level

Treble level

Balance

Fader

Volume offset

"Bas"/"BAS"

"Mid"/"MID"

"Tre"/"TRE"

"Bal"/"BAL"

"Fad"/"FAD"

"V-OFF"

–8 — +8

Left 15 — Right 15

Rear 15 — Front 15

Press the [SRC] button.

2 Select the Sound type

Press the [Q] button.

Each time the button is pressed the sound setting switches.

Sound setting

–8 —

Display

Volume offset: Each source's volume can be set as a difference

from the basic volume.

Flat

User memory

Rock

Pops

Easy

"Flat"/ "FLAT"

"User"/ "USER"

"Rock"/ "ROCK"

"Pops"/ "POPS"

"Easy"/ "EASY"

"Top40"/ "TOP40"

"Jazz"/ "JAZZ"

5 Exit Audio Control mode

Press the [AUD] button.

Top 40

Jazz

— 9 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

The frequency is displayed during Program Service name

reception (KDC-5020R only)

Press the [DISP] button for at least 1 second.

The frequency for the RDS station will be displayed for 5

seconds instead of the Program Service name.

Speaker Setting

Fine-tuning so that the System Q value is optimal when setting

the speaker type.

1 Enter Standby

Press the [SRC] button.

Select the "ALL OFF" display.

In CD & External disc source

KDC-MPV7020/6020 :

2 Enter Speaker Setting mode

Press the [Q] button.

Information

Display

Track number

Disc name

3 Select the Speaker type

Press the [4] or [¢] button.

Each time the button is pressed the setting switches as shown

below.

"DNPS"

Disc title (In External disc source or

KDC-MPV7020 internal CD source)

"D-TITLE"

Track title (In External disc source or

KDC-MPV7020 internal CD source)

"T-TITLE"

Speaker type

Display

Track number & Track Time

Clock

OFF

"SP OFF"

"SP 5/4"

"SP 6*9/6"

"SP OEM"

For 5 & 4 in. speaker

For 6 & 6x9 in. speaker

For the OEM speaker

KDC-5020/5020R :

Information

Display

Track number & Track Time

Disc name

4 Exit Speaker Setting mode

Press the [Q] button.

"DNPS"

Disc title (In External disc source)

Track title (In External disc source)

Clock

"D-TITLE"

"T-TITLE"

Switching Display

Switching the information displayed.

In MP3 source

Press the [DISP] button.

Each time the button is pressed the display switches as shown

below.

Information

Display

Track number

Disc name

Folder name

"DNPS"

In Tuner source

"FOL NAME"

"FIL NAME"

"TITLE"

Information

Display

File name

Frequency (KDC-MPV7020/6020/5020 only)

Station name (KDC-MPV7020/6020/5020 only)

Program Service name or Frequency (KDC-5020R only)

Radio text (KDC-5020R only)

Clock

Song title & Artist name

Album name & Artist name

Track Time

"SNPS"

"ALBUM"

"R-TEXT"

Clock

— 10 —

Download from Www.Somanuals.com. All Manuals Search And Download.

"N"

"C"

"E"

[#6]

[#2]

[#3]

Station/Disc Naming (SNPS/DNPS)

Attaching a title to a Station (KDC-MPV7020/6020/5020 only) or

CD.

6 Repeat steps 3 through 5 and enter the name.

1 Receive/play the station/disc you want to attach a title to

7 Exit name set mode

Press the [NAME] button.

• A title can't be attached to a MD.

KDC-MPV7020/6020:

• Disc Naming can't be done during CD text display.

KDC-5020/5020R:

• Disc Naming can't be done during CD text or clock display.

• When operation stops for 10 seconds the name at that time is

registered, and Name Set mode closes.

• Memory numbers

- FM: 32 stations

2 Enter name set mode

- AM: 16 stations

- Internal CD player: 30 (KDC-MPV7020/6020)/

10 (KDC-5020/5020R) discs

- External CD changer/ player: Varies according to the CD changer/

player. Refer to the CD changer/ player manual.

• The title of station/CD can be changed by the same operation

used to name it.

Press the [NAME] button for at least 2 seconds.

"NAME SET" is displayed.

3 Move the cursor to the enter character position

Press the [4] or [¢] button.

4 Select the character type (KDC-MPV7020/6020 only)

Press the [38] button.

Each time the button is pressed the character type switches as

shown below.

Function of the KDC-5020R

TEL Mute

The audio system automatically mutes when a call comes in.

Character type

Alphabet upper case

Alphabet lower case

Numbers and symbols

Special characters (Accent characters)

When a call comes in

"CALL" is displayed.

The audio system pauses.

Listening to the audio during a call

5 Select the characters

Press the [FM] or [AM] button.

Press the [SRC] button.

The "CALL" display disappears and the audio system comes back

ON.

Characters can be entered by using a remote with a number

buttons.

Example: If "DANCE" is entered.

When the call ends

Hang up the phone.

The "CALL" display disappears and the audio system comes back

ON.

Character

Button

#Times pressed

"D"

"A"

[#3]

[#2]

— 11 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Auxiliary Input Display Setting

Theft Deterrent Faceplate

Selecting the display when this device is switched to Auxiliary

input source.

The faceplate of the unit can be detached and taken with you,

helping to deter theft.

1 Select Auxiliary input source

Press the [SRC] button.

Select the "AUX" display.

Removing the Faceplate

1 Press the Release button.

Drop open the faceplate.

2 Enter Auxiliary input display setting mode

Press the [DISP] button for at least 2 seconds.

The presently selected AUX Name is blinks.

2 Drawing the faceplate to left side pull it to the front and

remove it.

3 Select the Auxiliary input display

Press the [4] or [¢] button.

Each time the button is pressed it switches through the below

displays.

• "AUX"

• "TV"

• "VCP"

• The faceplate is a precision piece of equipment and can be

damaged by shocks or jolts. For that reason, keep the faceplate in

its special storage case while detached.

• Do not expose the faceplate or its storage case to direct sunlight

or excessive heat or humidity. Also avoid places with too much

dust or the possibility of water splashing.

• "GAME"

• "PORTABLE"

• "DVD"

4 Exit Auxiliary input display setting mode

Press the [DISP] button.

Reattaching the Faceplate

• When operation stops for 10 seconds, the name at that time is

selected, and Auxiliary input display setting mode closes.

KDC-5020/5020R:

1 Align the shaft on the unit with the depression on the

faceplate.

• This function doesn't work when CA-C1AX is used.

Function of the KDC-MPV7020/KDC-6020

Non-fading Output

Turning the Non-fading output ON or OFF.

2 Push the faceplate in until it clicks.

The faceplate is locked in place, allowing you to use the unit.

Press the [NF] button for at least 1 second.

Each time the button is pressed Non-fading output switches ON

or OFF.

When it’s ON, "NF ON" is displayed.

— 12 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

Function of the KDC-5020R

Tuning

Selecting the station.

SRC FM MENU

1 Select tuner source

Press the [SRC] button.

Select the "TUNER" display.

OFF

DAB

PTY MENU

2 Select the band

SCAN

RDM

REP

M.RDM

DISP NAME TI

Press the [FM] or [AM] button.

Each time the [FM] button is pressed it switches between the

FM1, FM2, and FM3 bands.

AUD

LOUD

3 Tune up or down band

Press the [4] or [¢] button.

#1 – 6

During reception of stereo stations the "ST" indicator is ON.

Direct Access Tuning (Function of remote)

Entering the frequency and tuning.

ST indicator

1 Select the band

Press the [FM] or [AM] button.

2 Enter Direct Access Tuning mode

Press the [DIRECT] button on the remote.

"– – – –" is displayed.

3 Enter the frequency

Press the number buttons on the remote.

Example:

Band display

Frequency display

Preset station number

Desired frequency

Press button

92.1 MHz (FM)

810 kHz (AM)

[#0], [#9], [#2], [#1]

[#0], [#8], [#1], [#0]

Canceling Direct Access Tuning

Press the [DIRECT] button on the remote.

— 13 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

Function of the KDC-5020R

• When Auto Memory Entry is done in the FM2 band, the RDS

stations preset in the FM1 band aren't put in the memory.

Likewise, when it is done in the FM3 band, RDS stations preset in

FM1 or FM2 aren't put in the memory.

Station Preset Memory

Putting the station in the memory.

1 Select the band

Press the [FM] or [AM] button.

2 Select the frequency to put in the memory

Press the [4] or [¢] button.

Preset Tuning

Calling up the stations in the memory.

3 Put the frequency in the memory

Press the [#1] — [#6] button for at least 2 seconds.

The preset number display blinks 1 time.

On each band, 1 station can be put in the memory on each [#1]

— [#6] button.

1 Select the band

Press the [FM] or [AM] button.

2 Call up the station

Press the [#1] — [#6] button.

Auto Memory Entry

Putting a station with good reception in the memory

automatically.

1 Select the band for Auto Memory Entry

Press the [FM] or [AM] button.

2 Enter Menu mode

Press the [MENU] button for at least 1 second.

"MENU" is displayed.

3 Select the Auto Memory Entry mode

Press the [FM] or [AM] button.

Select the "A-MEMORY" display.

4 Open Auto Memory Entry

Press the [4] or [¢] button for at least 2 seconds.

When 6 stations that can be received are put in the memory

Auto Memory Entry closes.

• When the <AF Function> (page 29) is ON, only RDS stations are

put in the memory.

— 14 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS features

Function of the KDC-5020R

Traffic Information

Switching to traffic information automatically when a traffic

bulletin starts even when you aren't listening to the radio.

FM PTY

Press the [TI] button.

OFF

DAB

Each time the button is pressed the Traffic Information function

turns ON or OFF.

PTY MENU

When it's ON, "TI" indicator is ON.

SCAN

RDM

REP

M.RDM

DISP NAME TI

When a traffic information station isn't being received the "TI"

indicator blinks.

AUD

LOUD

When a traffic bulletin starts, "TRAFFIC" is displayed it and it

switches to traffic information.

#1 – 6

DISP TI

• During reception of a AM station when the Traffic Information

function is turned ON, it switches to a FM station.

• During reception of traffic information the adjusted volume is

automatically remembered, and the next time it switches to traffic

information it's automatically the remembered volume.

Receiving other traffic information stations

Press the [4] or [¢] button.

Traffic information station switching can be done when listening to

the radio.

PTY indicator TI indicator

Radio Text Scroll

Scrolling the displayed radio text.

Press the [DISP] button for at least 1 second.

— 15 —

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS features

Function of the KDC-5020R

21. Social Affairs

22. Religion

23. Phone In

24. Travel

25. Leisure

26. Jazz Music

27. Country Music

28. National Music

29. Oldies Music

30. Folk Music

31. Documentary

"SOCIAL"

PTY (Program Type)

Selecting the Program Type and searching for a station.

"RELIGION"

"PHONE IN"

"TRAVEL"

"LEISURE"

"JAZZ"

"COUNTRY"

"NATION M"

"OLDIES"

"FOLK M"

"DOCUMENT"

1 Enter PTY mode

Press the [PTY] button.

During PTY mode the "PTY" indicator is ON.

This function can't be used during a traffic bulletin or AM reception.

2 Select the Program Type

Press the [FM] or [AM] button.

Each time the button is pressed the Program Type switches as

shown below.

• Speech and Music include the Program type shown below.

Music: No.12 — 17, 26 — 30

Speech: No.3 — 11, 18 — 25, 31

• The Program Type can be put in the [#1] — [#6] button memory

and called up quickly. Refer to the <Program Type preset> (page

16).

• The display language can be changed. Refer to <Changing

Language for PTY Function> (page 17).

No. Program Type

Display

Speech

Music

News

Current Affairs

Information

Sport

Education

Drama

"SPEECH"

"MUSIC"

"NEWS"

"AFFAIRS"

"INFO"

"SPORT"

"EDUCATE"

"DRAMA"

"CULTURE"

"SCIENCE"

"VARIED"

"POP M"

"ROCK M"

3 Search for the selected Program Type station

Press the [4] or [¢] button.

When you want to search for other stations press the [4] or

[¢] button again.

Culture

When the selected Program Type isn't found, "NO PTY" is displayed.

Select another Program Type.

10. Science

11. Varied

12. Pop Music

13. Rock Music

4 Exit PTY mode

Press the [PTY] button.

14. Easy Listening Music "EASY M"

15. Light Classical

16. Serious Classical

17. Other Music

18. Weather

19. Finance

20. Children's programs

"LIGHT M"

"CLASSICS"

"OTHER M"

"WEATHER"

"FINANCE"

"CHILDREN"

Program Type preset

Putting the Program Type in the Preset button memory and

calling it up quickly.

— 16 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

Function of the KDC-MPV7020/KDC-6020/KDC-5020

Presetting the Program Type

SRC FM MENU

1 Select the Program Type to preset

Refer to <PTY(Program Type)> (page 16).

OFF

DAB

2 Preset the Program Type

Press the [#1] — [#6] button for at least 2 seconds.

Calling up the preset Program Type

SCAN

RDM

REP

M.RDM

DISP NAME AUTO AME

AUD

1 Enter PTY mode

Refer to <PTY(Program Type)> (page 16).

LOUD

2 Call up the Program Type

Press the [#1] — [#6] button.

#1 – 6

AUTO/AME

KDC-MPV7020/6020

ST indicator

Preset station number

Changing Language for PTY Function

Selecting the Program Type display language.

1 Enter PTY mode

Refer to <PTY (Program Type)> (page 16).

2 Enter Changing Language mode

Press the [DISP] button.

Band display

Frequency display

3 Select the language

Press the [FM] or [AM] button.

Each time the button is pressed the language switches as shown

below.

KDC-5020

ST indicator

Language

Display

English

French

Swedish

German

"ENGLISH"

"FRENCH"

"SWEDISH"

"GERMAN"

4 Exit Changing Language mode

Press the [DISP] button.

Band display

Frequency display

Preset station number

— 17 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

Function of the KDC-MPV7020/KDC-6020/KDC-5020

Tuning Mode

Direct Access Tuning (Function of remote)

Choose the tuning mode.

Entering the frequency and tuning.

Press the [AUTO] button.

Each time the button is pressed the Tuning mode switches as

shown below.

1 Select the band

Press the [FM] or [AM] button.

2 Enter Direct Access Tuning mode

Press the [DIRECT] button on the remote.

"– – – –" is displayed.

Tuning mode

Display

Operation

Auto seek

"Auto 1"/

"AUTO 1"

Automatic search for a station.

Preset station

seek

Manual

"Auto 2"/

"AUTO 2"

"Manual"/

"MANUAL"

Search in order of the stations

in the Preset memory.

Normal manual tuning control.

3 Enter the frequency

Press the number buttons on the remote.

Example:

Desired frequency

Press button

92.1 MHz (FM)

810 kHz (AM)

[#0], [#9], [#2], [#1]

[#0], [#8], [#1], [#0]

Canceling Direct Access Tuning

Tuning

Selecting the station.

Press the [DIRECT] button on the remote.

1 Select tuner source

Press the [SRC] button.

Select the "TUNER" display.

Station Preset Memory

Putting the station in the memory.

2 Select the band

Press the [FM] or [AM] button.

Each time the [FM] button is pressed it switches between the

FM1, FM2, and FM3 bands.

1 Select the band

Press the [FM] or [AM] button.

2 Select the frequency to put in the memory

Press the [4] or [¢] button.

3 Tune up or down band

Press the [4] or [¢] button.

3 Put the frequency in the memory

Press the [#1] — [#6] button for at least 2 seconds.

The preset number display blinks 1 time.

On each band, 1 station can be put in the memory on each [#1]

— [#6] button.

During reception of stereo stations the "ST" indicator is ON.

— 18 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Function of the KDC-MPV7020/KDC-6020

Preset Tuning

Auto Memory Entry

Putting a station with good reception in the memory

automatically.

Calling up the stations in the memory.

1 Select the band

Press the [FM] or [AM] button.

1 Select the band for Auto Memory Entry

Press the [FM] or [AM] button.

2 Call up the station

Press the [#1] — [#6] button.

2 Enter Menu mode

Press the [MENU] button for at least 1 second.

"MENU" is displayed.

Frequency Step Setting

Changing the tuning frequency step.

The original setting is FM band 50 kHz, and AM band 9 kHz.

3 Select the Auto Memory Entry mode

Press the [FM] or [AM] button.

Select the "A-Memory" display.

While pressing the [#1] and [#5] button, press the Reset

button.

The frequency step changes to FM band 200 kHz, and AM band

10 kHz.

4 Open Auto Memory Entry

Press the [4] or [¢] button for at least 2 seconds.

When 6 stations that can be received are put in the memory

Auto Memory Entry closes.

When the frequency step is switched, the frequencies in the

memory are deleted.

Function of the KDC-5020

Auto Memory Entry

Putting stations with good reception in the memory

automatically.

1 Select the band for Auto Memory Entry

Press the [FM] or [AM] button.

2 Open Auto Memory Entry

Press the [AME] button for at least 2 seconds.

When 6 stations that can be received are put in the memory

Auto Memory Entry closes.

— 19 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/MP3/External disc control features

Release button

SRC FM

Playing CD & MP3

When there is no disc inserted

OFF

DAB

1 Drop open the faceplate

Press the Release button.

2 Insert a disc.

SCAN

RDM

REP

M.RDM

DISP NAME AUTO GSM

AUD

3 Press the faceplate on the right side, and return it to its

former position.

LOUD

• When the faceplate has been dropped open, it might interfere

with the shift lever or something else. If this happens, pay

attention to safety and move the shift lever or take an appropriate

action, then operate the unit.

• Do not use the unit with the faceplate in the open condition. If it's

used in the open position dust can enter the inside part and cause

damage.

SCAN RDM REP #5 M.RDM DISP

/ #3

KDC-MPV7020/6020

IN indicator

• The models that can play MP3 is shown below.

KDC-MPV7020

• When a disc is inserted, the "IN" indicator is ON.

When a disc is inserted

Press the [SRC] button.

Select the "CD" display.

Pause and play

Disc number

Track time

Track number

Press the [38] button.

Each time the button is pressed it pauses and plays.

KDC-5020/5020R

Eject the disc

IN indicator

1 Drop open the faceplate

Press the Release button.

2 Eject the disc

Press the [0] button.

Disc number

Download from Www.Somanuals.com. All Manuals Search And Download.

Track number

Track time

— 20 —

• Disc #10 is displayed as "0".

• The functions that can be used and the information that can be

displayed will differ depending on the external disc players being

connected.

Fast Forwarding and Reversing

Fast Forwarding

Hold down on the [¢] button.

Release your finger to play the disc at that point.

3 Press the faceplate on the right side, and return it to its

former position.

Reversing

Hold down on the [4] button.

Release your finger to play the disc at that point.

3 in. (8cm) disc can't be played. Using an adapter and inserting them

into this unit can cause damage.

The MP3 media that this unit can play are CD-ROM, CD-R, and CD-

RW.

The medium formats must be ISO 9660 Level 1, Level 2, Joliet, or

Romeo. The methods and precautions to be followed for writing

MP3 data are covered in <Notes on playing MP3> (page 6).

Check that section before creating your MP3 media.

Track Search

Selecting the song you want to hear.

Searching for a song on the disc or in the MP3 folder.

Press the [4] or [¢] button.

Playing External Disc

Album Search

Playing discs set in the optional accessory disc player connected

to this unit.

Selecting the disc set in the Disc changer or the folder recorded

on the MP3 media.

Press the [SRC] button.

Press the [FM] or [AM] button.

Select the display for the disc player you want.

Display examples:

Display

Disc player

"CD2"

CD player

"DISC-CH"

CD changer/ MD changer

Pause and play

Press the [38] button.

Each time the button is pressed it pauses and plays.

— 21 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/MP3/External disc control features

Repeat play

Display

Direct Track Search (Function of remote)

Doing Track Search by entering the track number.

Track Repeat (In CD/MD)

(In MP3)

"REP ON"/"T-REP ON"

"REP ON"

Album Repeat (In Disc Changer)

(In MP3 media)

OFF

"D-REP ON"

"F REP ON"

"REP OFF"

1 Enter the track number

Press the number buttons on the remote.

2 Do Track Search

Press the [4] or [¢] button.

Canceling Direct Track Search

Track Scan

Press the [38] button.

Playing the first part of each song on the disc or MP3 folder you

are listening to and searching for the song you want to listen to.

1 Start Track Scan

Direct Album Search

Press the [SCAN] button.

(Function of disc changers with remote)

"Scan ON"/ "SCAN ON"/ "SCN ON" is displayed.

Doing Disc Search by entering the disc number.

2 Release it when the song you want to listen to is played

Press the [SCAN] button.

1 Enter the disc number

Press the number buttons on the remote.

2 Do Album Search

Press the [DISC+] or [DISC–] button.

Random Play

Play all the songs on the disc or MP3 folder in random order.

Canceling Direct Album Search

Press the [38] button.

Press the [RDM] button.

Each time the button is pressed Random Play turns ON or OFF.

When it's ON, "RDM ON" is displayed.

Input "0" to select disc 10.

When the [¢] button is pressed, the next song select starts.

Track/Album Repeat

Replaying the song, disc in the Disc changer or MP3 folder

you're listening to.

Magazine Random Play

(Function of disc changer)

Press the [REP] button.

Each time the button is pressed the Repeat Play switches as

shown below.

Play the songs on all the discs in the disc changer in random

order.

— 22 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Press the [M.RDM] button.

Each time the button is pressed the Magazine Random Play turns

ON or OFF.

3 Decide the folder to play

Press the [38] button.

The Album Select mode releases, and the MP3 in the folder

being displayed is played.

When it's ON, "MRDM ON" is displayed.

The methods for moving to other folders in the album select mode

are different from those in the album search mode.

See <Notes on playing MP3> (page 6) for details.

When the [¢] button is pressed, the next song select starts.

Canceling the Album Select mode

Function of the KDC-MPV7020/KDC-6020

Album Select (Function of MP3)

Press the [#5] button.

Quickly selecting the folder you want to listen to.

Text/Title Scroll

Scrolling the displayed CD text, MP3 text, or MD title.

Press the [DISP] button for at least 1 second.

1 Enter Album Select mode

Press the [#5] button.

"SELECT MODE" is displayed.

During Select mode the folder information is displayed as shown

below.

DNPP (Disc Name Preset Play)

(Function of disc changers with remote)

Selecting the CD displayed in the DNPS of the CDs set in the

Disc changer.

Displays the current folder name.

1 Enter DNPP mode

Press the [DNPP] button on the remote.

When "DNPP" is displayed the DNPS display in order.

2 Select the folder level

Press the [FM] or [AM] button.

With the [FM] button you move 1 level down and with the [AM]

button 1 level up.

Forward / Reverse display

Press the [DISC–] or [DISC+] button.

2 When the disc you want is displayed

Press the [OK] button on the remote.

The disc being displayed is played.

Selecting a folder in the same level

Press the [4] or [¢] button.

With the [4] button you move to the previous folder, and with

the [¢] button to the next folder.

Canceling the DNPP mode

Press the [DNPP] button on the remote.

Returning to the top level

Press the [#3] button.

— 23 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu system

SRC FM MENU

Menu System

Setting during operation beep sound etc. functions.

The Menu system basic operation method is explained here. The

reference for the Menu items and their setting content is after

this operation explanation.

OFF

DAB

PTY MENU

SCAN

RDM

REP

M.RDM

DISP NAME TI GSM

1 Enter Menu mode

Press the [MENU] button for at least 1 second.

"MENU" is displayed.

AUD

LOUD

2 Select the menu item

Press the [FM] or [AM] button.

Example: When you want to set the beep sound select the

"Beep"/ "BEEP" display.

DISP

#1 – 6

KDC-MPV7020/6020

3 Set the menu item

Press the [4] or [¢] button.

Example: When "Beep"/ "BEEP" is selected, each time the button

is pressed it switches "Beep ON"/ "BEEP ON" or "Beep

OFF"/ "BEEP OFF". Select 1 of them as the setting.

You can continue by returning to step 2 and setting other items.

4 Exit Menu mode

Press the [MENU] button.

Menu display

When other items that are applicable to the basic operation method

above are displayed afterwards their setting content chart is

entered. (Normally the uppermost setting in the chart is the original

setting.)

Also, the explanation for items that aren't applicable (<Manual Clock

Adjustment>etc.) are entered step by step.

KDC-5020/5020R

NEWS indicator

(KDC-5020R)

RDS indicator

(KDC-5020R)

Security Code

Because authorization by the Security Code is required when it's

removed from the vehicle, personalizing this unit is by using the

Security Code is a help in preventing theft.

Menu display

— 24 —

Download from Www.Somanuals.com. All Manuals Search And Download.

"APPROVED" is displayed.

The unit can be used.

When the Security Code function is activated it can't be released.

Note, your Security Code is the 4 digit number entered in your "Car

Audio Passport" in this package.

If an incorrect code is input, "WAITING" is displayed, and the input

prohibited time shown below is generated.

After the input prohibited time lapses, "CODE" is displayed, and

input can be done.

1 Enter Standby

Press the [SRC] button.

Select the "ALL OFF" display.

Number of times

the incorrect code was input

Input prohibited time

2 Enter Menu mode

Press the [MENU] button for at least 1 second.

When "MENU" is displayed, "Security"/ "SECURITY" is displayed.

—

5 minutes

1 hour

24 hours

3 Enter Security Code mode

Press the [4] or [¢] button for at least 1 second.

When "ENTER" is displayed, "CODE" is displayed.

4 Select the digits to enter

Press the [4] or [¢] button.

Touch Sensor Tone

Setting the operation check sound (beep sound) ON/OFF.

5 Select the Security Code numbers

Press the [FM] or [AM] button.

6 Repeat steps 4 and 5, and complete the Security Code.

Display

Setting

"Beep ON"/ "BEEP ON"

"Beep OFF"/ "BEEP OFF"

Beep is heard.

Beep canceled.

7 Confirm the Security Code

Press the [¢] button for at least 3 seconds.

When "RE-ENTER" is displayed, "CODE" is displayed.

8 Do the step 4 through 7 step operation, and reenter the

security code.

"APPROVED" is displayed.

The Security Code function activates.

If you enter a Code different from your Security Code, you have to

start over from step 4.

Press the Reset button and when it's removed from the

battery power source

1 Turn the power ON.

2 Do the step 4 through 7 step operation, and reenter the

security code.

— 25 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu system

removed, warning potential thieves.

Manual Clock Adjustment

Display

Setting

This adjustment can be done when the <Synchronize Clock> (page

"DSI ON"

"DSI OFF"

LED flashes.

LED OFF.

26) is set as OFF.

1 Select Clock Adjustment mode

Press the [FM] or [AM] button.

Select the "CLK ADJ" display.

2 Enter Clock Adjust mode

Function of the KDC-MPV7020/KDC-6020/KDC-5020R

Press the [4] or [¢] button for at least 1 second.

The clock display blinks.

Selectable Illumination

Selecting the button illumination color as green or red.

3 Adjust the hours

Press the [FM] or [AM] button.

Display

Setting

"KEY GRN"

"KEY RED"

The illumination color is green.

The illumination color is red.

Adjust the minutes

Press the [4] or [¢] button.

4 Exit Clock adjustment mode

Press the [MENU] button.

Function of the KDC-5020/KDC-5020R

Switching Graphic Display

Setting the graphic part display ON/OFF.

Function of the KDC-5020R

Synchronize Clock

Display

Setting

"GRPH ON"

"GRPH OFF"

The graphic part is displayed.

The graphic part isn't displayed.

Synchronizing the RDS station time data and this unit's clock.

Display

Setting

"SYNC ON"

"SYNC OFF"

Synchronizes the time.

Adjust the time manually.

Function of the KDC-MPV7020/KDC-6020

It takes 3 to 4 minutes to synchronize the clock.

Switching Display Type

Setting the Display type.

Display

Setting

DSI (Disabled System Indicator)

A red indicator will blink on the unit after the faceplate is

"DisplayD"

"DisplayA"

Demonstration.

Circle Display is play time.

— 26 —

Download from Www.Somanuals.com. All Manuals Search And Download.

"DisplayB"

"DisplayC"

Circle Display is clock.

Silent display type.

Blue fine adjustment

Press the [#3] button for at least 2 seconds.

Press the [4] or [¢] button.

When the blue fine adjustment is completed, press the [#3]

button.

Function of the KDC-MPV7020

The set color memory

Illumination Color Setting

You can set the display to a desired color.

Press the [#5] button for at least 2 seconds.

When the setting in the memory is called up press the [#5]

button.

1 Select Illumination Color Setting Mode

Press the [FM] or [AM] button.

Select the "COL" display.

The blue fine adjustment setting cannot be stored in memory.

2 The color continues to change gradually

Continue pressing the [4] or [¢] button.

Release your finger at the color you want.

Function of the KDC-MPV7020/KDC-6020

Contrast Adjustment

Adjusting the display contrast.

Quick call up the preset color

Press the [#1] — [#4] button.

Button

Display and Setting

Color

"CONT 0"

[#1]

[#2]

[#3]

[#4]

Silky White

Red

Blue

"CONT 5" (Original setting)

"CONT 10"

Blue Green

Selecting the Color mode

Press the [#6] button.

Each time the button is pressed the Color mode switches as

shown below.

Function of the KDC-MPV7020/KDC-6020

Dimmer

Display

Color mode

Dimming this unit's display automatically when the vehicle light

switch is turned ON.

"Scan"

"SRC"

"Time"

The color changes in sequence.

The color changes according to the selected source.

The color changes every 6 hours.

Display

Setting

Keeps the presently set color.

"DIM ON"

"DIM OFF"

The display dims.

The display doesn't dim.

— 27 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu system

Function of the KDC-MPV7020/KDC-6020

Function of the KDC-5020R

Switching preout

Local Seek <In Tuner mode>

Switching the preout between the rear and non-fading. (In non-

fading it outputs without effect from the fader control.)

Only stations whose reception is good are searched for in auto

seek tuning.

Display

Setting

Display

Setting

"SWPRE R"

"SWPRE NF"

Rear preout.

Non-fading preout.

"LO.S OFF"

"LO.S ON"

The local seek function is OFF.

The local seek function is ON.

Function of the KDC-5020R

Tuning Mode <In Tuner mode>

News Bulletin with Timeout Setting

Sets the tuning mode.

It switches automatically when a news bulletin starts even if the

radio isn't being listened to. Also, the time interval when

interrupt is prohibited can be set.

Tuning mode

Display

Operation

Auto seek

Preset station seek "AUTO 2"

"AUTO 1"

Automatic search for a station.

Display and Setting

Search in order of the stations

in the Preset memory.

"MANUAL" Normal manual tuning control.

"NEWS OFF"

"NEWS 00M"

Manual

"NEWS 90M"

When "NEWS 00M" — "NEWS 90M" is set, the News Bulletin

Interrupt function is ON.

When it's ON, the "NEWS" indicator is ON.

When the news bulletin starts, "NEWS" is displayed, and it

switches to the news bulletin.

Function of the KDC-MPV7020/KDC-6020/KDC-5020R

Auto Memory Entry <In Tuner mode>

For the operation method refer to <Auto Memory Entry> (page

14/ 19).

• If you choose the "20M" setting, further news bulletins will not be

received for 20 minutes once the first news bulletin is received.

• The news bulletin volume is the same level that was set for traffic

information (page 15).

Function of the KDC-MPV7020/KDC-6020/KDC-5020

• This function is only available if the desired station sends PTY-code

for news bulletin or belongs to <Enhanced Other Network>-

Network sending PTY-code for news bulletin.

• When the News Bulletin Interrupt function is ON, it switches to an

FM station.

CRSC (Clean Reception System Circuit)

Temporarily have reception switched from stereo to mono to

reduce multi-path noise when listening to the FM station.

— 28 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Display

Setting

Sometimes stations in the same network broadcast different

programs or use different program service names.

"CRSC ON"

"CRSC OFF"

The CRSC is ON.

The CRSC is OFF.

Strong electrical fields (such as from power lines) may cause

unstable sound quality when CRSC is turned ON. In such a situation,

turn it OFF.

Function of the KDC-5020R

Auto TP Seek

When the TI function is ON and poor reception conditions are

experienced when listening to a traffic information station,

another traffic information station with better reception will be

searched for automatically.

Function of the KDC-5020R

AF (Alternative Frequency)

When poor reception is experienced, automatically switch to

another frequency broadcasting the same program in the same

RDS network with better reception.

Display

Setting

"ATPS ON"

"ATPS OFF"

The Auto TP Seek Function is ON.

The Auto TP Seek Function is OFF.

Display

Setting

"AF ON"

"AF OFF"

The AF function is ON.

The AF function is OFF.

Function of the KDC-5020R

When the AF function is ON, the "RDS" indicator is ON.

Monaural Reception <In FM reception>

Noise can be reduced when stereo broadcasts are received as

monaural.

When no other stations with stronger reception are available for the

same program in the RDS network, you may hear the incoming

broadcast in bits and snatches. Turn OFF the AF function in such a

case.

Display

Setting

"MONO OFF"

"MONO ON"

The monaural reception is OFF.

The monaural reception is ON.

Function of the KDC-5020R

Restricting RDS Region

(Region Restrict Function)

You can choose whether or not to restrict the RDS channels,

received with the AF function for a particular network, to a

specific region.

Display

Setting

"REG ON"

"REG OFF"

The Region Restrict Function is ON.

The Region Restrict Function is OFF.

— 29 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu system

Basic Operations of remote

Function of the KDC-MPV7020/KDC-6020/KDC-5020

Text Scroll

Setting the displayed text scroll.

Display

Setting

"SCL AUTO"

"SCL MANU"

Repeats scroll.

Scrolls when the display changes.

4/¢

The text scrolled is shown below.

• CD text

• Folder name/ File name/ Song title/ Artist name/ Album name

• MD title

FM/AM/DISC+/DISC–

[#0] — [#9]

Function of the KDC-5020R

Text Scroll

Setting the displayed text scroll.

DIRECT/OK

DNPP

Display

Setting

"SCL MANU"

"SCL AUTO"

Doesn't scroll.

Scrolls when the display changes.

ATT

VOL.

The text scrolled is shown below.

• CD text

• MD title

• Radio text

SRC

Function of the KDC-MPV7020/KDC-6020

Built-in Auxiliary input Setting

Set the Built-in Auxiliary Input function.

Display

Setting

"AUX OFF" When selecting the source there's no Auxiliary Input.

"AUX ON" When selecting the source there's Auxiliary Input.

— 30 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading and Replacing the battery

In Tuner source

Use one lithium battery (CR2025).

Insert the batteries with the + and – poles aligned properly,

following the illustration inside the case.

[FM]/ [AM] buttons

Select the band.

Each time the [FM] button is pressed it switches between the

FM1, FM2, and FM3 bands.

[4]/ [¢] buttons

Tune up or down band.

[#0] — [#9] buttons

Press buttons [#1] — [#6] to recall preset stations.

[DIRECT] button

Enters and cancels the <Direct Access Tuning> (page 13/ 18)

mode.

2WARNING

Store unused batteries out of the reach of children. Contact a doctor

immediately if the battery is accidentally swallowed.

[38] button (KDC-5020R only)

Enters and cancels the <PTY (Program Type)> (page 16) mode.

Do not set the remote on hot places such as above the dashboard.

In Disc source

Basic operations

[4]/ [¢] buttons

Doing track forward and backward.

[VOL.] buttons

Adjusting the volume.

[DISC+]/ [DISC–] buttons

Doing album forward and backward.

[SRC] button

Each time the button is pressed the source switches.

For the source switching order refer to <Selecting the Source>

(page 8).

[38] button

Each time the button is pressed the song pauses and plays.

[DNPP]/ [OK] button

[ATT] button

Enters and cancels the <DNPP (Disc Name Preset Play)> (page

23) mode.

Turning the volume down quickly.

When it is pressed again it returns to the previous level.

[#0] — [#9] buttons

When in <Direct Track Search> (page 22) and <Direct Album

Search> (page 22), enter the track/disc number.

— 31 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories (KDC-MPV7020/6020/5020)

External view

......... Number of items

External view

......... Number of items

2WARNING

If you connect the ignition wire (red) and the battery wire (yellow)

to the car chassis (ground), you may cause a short circuit, that in

turn may start a fire. Always connect those wires to the power

source running through the fuse box.

.........4

.........2

.........1

.........2

2CAUTION

• If your car's ignition does not have an ACC position, connect the

ignition wires to a power source that can be turned on and off

with the ignition key. If you connect the ignition wire to a power

source with a constant voltage supply, as with battery wires, the

battery may die.

• If the console has a lid, make sure to install the unit so that the

faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching to

cause a short circuit, then replace the old fuse with one with the

same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps on

the ends of the unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to which

they correspond. The unit may be damaged or fail to work if you

share the - wires or ground them to any metal part in the car.

• When only two speakers are being connected to the system,

connect the connectors either to both the front output terminals

or to both the rear output terminals (do not mix front and rear).

For example, if you connect the + connector of the left speaker

to a front output terminal, do not connect the - connector to a

rear output terminal

The use of any accessories except for those provided might result in

damage to the unit. Make sure only to use the accessories shipped with

the unit, as shown above.

Installation Procedure (KDC-MPV7020/6020/5020)

1. To prevent a short circuit, remove the key from the ignition and

disconnect the - battery.

2. Make the proper input and output wire connections for each unit.

3. Connect the speaker wires of the wiring harness.

4. Connect the wiring harness wires in the following order: ground,

battery, ignition.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

— 32 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Wires to Terminals (KDC-MPV7020/6020/5020)

11 Rear right output (Red)/

12 Non-fading right output (Red) (KDC-MPV7020/6020 only)

10 Rear left output (White)/

49 Non-fading left output (White) (KDC-MPV7020/6020 only)

AUX right input (Red) (KDC-MPV7020/6020 only)

AUX left input (White) (KDC-MPV7020/6020 only)

To KENWOOD disc changer/

DAB control input/KPA-SD100/

KPA-HD100/KPA-SS100 25

13 Front right output (Red)

To connect these leads,

refer to the relevant

instruction manuals. 26

14 Front left output (White)

FM/AM antenna input

If no connections are made, do not let the wire come out from the tab. 3

Fuse (10A) 27

Wiring harness

4 When using the optional power amplifier,

(Accessory1)22

connect to its power control terminal.

P.CONT

Power control wire (Blue/White)

5 Depending on what antenna you are using, connect

either to the control terminal of the motor antenna, or

to the power terminal for the booster amplifier of the

film-type antenna.

White/Black

ANT.

CONT

To front left

speaker 29

Motor antenna control wire (Blue)

FRONT • L

White

7 To car light control switch

ILLUMI

Gray/Black

Dimmer control wire (Orange / White)

(KDC-MPV7020/6020 only) 19

To front right

speaker 32

FRONT • R

Ignition key

switch 41

Gray

Green/Black

ACC 44

To rear left

REAR • L

Ignition wire (Red) 46

speaker 35

Green

Car fuse box

(Main fuse)

Purple/Black

Battery wire (Yellow)

Car fuse box 45

To rear right

speaker 38

Ground wire (Black) - (To car chassis) 48

REAR • R

–

Purple

Battery

— 33 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories (KDC-5020R)

External view

......... Number of items

2WARNING

......... Number of items

If you connect the ignition wire (red) and the battery wire (yellow)

to the car chassis (ground), you may cause a short circuit, that in

turn may start a fire. Always connect those wires to the power

source running through the fuse box.

.........4

.........2

.........1

2CAUTION

• If your car's ignition does not have an ACC position, connect the

ignition wires to a power source that can be turned on and off

with the ignition key. If you connect the ignition wire to a power

source with a constant voltage supply, as with battery wires, the

battery may die.

• If the console has a lid, make sure to install the unit so that the

faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching to

cause a short circuit, then replace the old fuse with one with the

same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps on

the ends of the unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to which

they correspond. The unit may be damaged or fail to work if you

share the - wires or ground them to any metal part in the car.

• When only two speakers are being connected to the system,

connect the connectors either to both the front output terminals

or to both the rear output terminals (do not mix front and rear).

For example, if you connect the + connector of the left speaker

to a front output terminal, do not connect the - connector to a

rear output terminal

.........2

.........4

The use of any accessories except for those provided might result in

damage to the unit. Make sure only to use the accessories shipped with

the unit, as shown above.

Installation Procedure (KDC-5020R)

1. To prevent a short circuit, remove the key from the ignition and

disconnect the - battery.

2. Make the proper input and output wire connections for each unit.

3. Connect the wire on the wiring harness.

4. Take Connector B on the wiring harness and connect it to the

speaker connector in your vehicle.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

5. Take Connector A on the wiring harness and connect it to the

external power connector on your vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

8. Reconnect the - battery.

9. Press the reset button.

— 34 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Wires to Terminals (KDC-5020R)

4 Rear right output (Red)

Connector Function Guide

Pin Numbers for

ISO Connectors

10 Rear left output (White)

Cable Colour

Functions

External Power

Connector

5 Front right output (Red)

A–4

A–5

A–7

A–8

Yellow

Blue/White

Red

Battery

Power Control

Ignition (ACC)

Earth (Ground)

Connection

12 Front left output (White)

FM/AM antenna input 3

Black

Antenna Cord (ISO) 1

Speaker

Connector

Antenna Conversion Adaptor (ISO–JASO) (Accessory6) 2

B–1

B–2

B–3

B–4

B–5

B–6

B–7

B–8

Purple

Purple/Black

Gray

Gray/Black

White

White/Black

Green

Rear Right (+)

Rear Right (–)

Front Right (+)

Front Right (–)

Front Left (+)

Front Left (–)

Rear Left (+)

Rear Left (–)

Fuse (10A) 13

Wiring harness

(Accessory1) 16

KENWOOD disc changer input 14

To connect the Disc changer, consult your

Disc changer manual. 15

Green/Black

TEL mute wire (Brown)

Connect to the terminal that is

grounded when either the telephone

rings or during conversation. 21

Battery wire (Yellow) 6

TEL MUTE

Ignition wire (Red) 7

Power control/ Motor antenna

A–7 Pin (Red) 8

A–4 Pin (Yellow) 9

Connector A

Connect either to the power control

terminal when using the optional

power amplifier, or to the antenna

control terminal in the vehicle. 23

control wire (Blue/White) 20

P.CONT

ANT.CONT.

If no connections are made, do not let the wire

come out from the tab. 18

Connector B

— 35 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Wires to Terminals (KDC-5020R)

When the connection is made as in 3 above, the unit's

power will not be linked to the ignition key. For that reason,

always make sure to turn off the unit's power when the

ignition is turned off.

To link the unit's power to the ignition, connect the ignition

cable (ACC...red) to a power source that can be turned on

and off with the ignition key.

2WARNING

Connecting the ISO Connector (see p.23)

The pin arrangement for the ISO connectors depends on the

type of vehicle you drive. Make sure to make the proper

connections to prevent damage to the unit.

The default connection for the wiring harness is described in 1

below. If the ISO connector pins are set as described in 2 or 3,

make the connection as illustrated.

1 (Default setting) The A-7 pin (red) of the vehicle's ISO

connector is linked with the ignition, and the A-4 pin (yellow) is

connected to the constant power supply.

Unit

Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

2 The A-7 pin (red) of the vehicle's ISO connector is connected

to the constant power supply, and the A-4 pin (yellow) is linked

to the ignition.

Unit

Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

3 The A-4 pin (yellow) of the vehicle's ISO connector is not

connected to anything, while the A-7 pin (red) is connected to

the constant power supply (or both the A-7 (red) and A-4

(yellow) pins are connected to the constant power supply).

Unit

Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

— 36 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

■ Installation

■ Installing in Japanese-Made Cars

1 Refer to the section "Removing the hard rubber frame" (page 38)

and then remove the hard rubber frame.

Firewall or metal support

2 Align the holes in the unit (two locations on each side) with the

vehicle mounting bracket and secure the unit with the accessory

screws.

Screw (M4X8)

(commercially

available)

8 mm

8mm

MAX.

T/N

ø5mm

Bend the tabs of the

mounting sleeve

with a screwdriver or

similar utensil and

attach it in place.

T: Toyota cars

N: Nissan cars

Accessory3...for Nissan car

Accessory4 ...for Toyota car

• During installation, do not use any screws except for those provided.

The use of different screws might result in damage to the main unit.

• Damage may occur if a screwdriver or similar tool is used with

excessive force during the installations.

Metal mounting strap

(commercially available)

Self-tapping screw

(commercially available)

Make sure that the unit is installed securely in place. If the unit is

unstable, it may malfunction (for example, the sound may skip).

■ Screwing the Faceplate on the Unit

If you want to fasten the

faceplate to the main unit so

that it does not fall off,

screw in the provided

Accessory5

Bottom panel

screws (ø4 X 16 mm) in the

holes shown below.

Never insert the taptite screw (ø4 × 16 mm) in any other screw hole

than the one specified. If you screw it in another hole, it will contact

and may cause damage to the mechanical parts inside the unit.

— 37 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

■ Removing the hard rubber frame

■ Removing the Unit

1 Refer to the section “Removing the hard rubber frame” and then

remove the hard rubber frame.

1 Engage the catch pins on the removal tool and remove the two

locks on the lower level.

Lower the frame and pull it forward as shown in the figure.

2 Remove the screw (M4 × 8) on the back panel.

3 Insert the two removal tools deeply into the slots on each side,

as shown.

Catch

Lock

Accessory2

Screw (M4X8)

Removal tool

(commercially

available)

Accessory2

Removal tool

2 When the lower level is removed, remove the upper two

locations.

4 Lower the removal tool

toward the bottom, and pull

out the unit halfway while

pressing towards the inside.

Be careful to avoid injury from

the catch pins on the removal

tool.

5 Pull the unit all the way out

with your hands, being

careful not to drop it.

The frame can be removed from the top side in the same manner.

— 38 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

What might seem to be a malfunction in your unit may

just be the result of slight misoperation or miswiring.

Before calling service, first check the following table

for possible problems.

? The TEL mute function does not work.15

✔

The TEL mute wire is not connected properly.

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

? The TEL mute function turns ON even though the TEL mute wire is

General

not connected.16

✔

The TEL mute wire is touching a metal part of the car.

? The power does not turn ON.01

☞ Pull the TEL mute wire away from the metal part of the car.

✔

The fuse has blown.

☞ After checking for short circuits in the wires, replace the fuse with

one with the same rating.

? Even if Loudness is turned ON, high-pitched tone isn't compensated

for. 17

✔

Tuner source is selected.

✔

No ACC position on vehicle ignition.02

☞ Connect the same wire to the ignition as the battery wire.

☞ High-pitched tone isn't compensated for when in Tuner source.

? No sound can be heard, or the volume is low.

? Nothing happens when the buttons are pressed.04

✔

The fader or balance settings are set all the way to one side.21

✔

The computer chip in the unit is not functioning normally.

☞ Center the fader and balance settings.

☞ Press the reset button on the unit (page 4).

✔

The input/output wires or wiring harness are connected incorrectly.22

☞ Reconnect the input/output wires or the wiring harness correctly.

See the section on <Connecting Wires to Terminals>.

? There’s a source you can’t switch.06

✔

There’s no CD inserted.

☞ Set the media you want to listen to. If there’s no media in this

unit, you can't switch to each source.

✔

The values of Volume offset are low.24

☞ Increase the values of Volume offset. (page 9)

✔

The Disc changer isn’t connected.08

☞ Connect the Disc changer. If the Disc changer isn’t connected to

it's input terminal, You can't switch to an external disc source.

? The sound quality is poor or distorted.25

✔

One of the speaker wires is being pinched by a screw in the car.

☞ Check the speaker wiring.

? The memory is erased when the ignition is turned OFF.10

✔

The speakers are not wired correctly.27

✔

The battery wire has not been connected to the proper terminal.

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

☞ Reconnect the speaker wires so that each output terminal is

connected to a different speaker.

✔

The ignition and battery wire are incorrectly connected.11

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

? ^{The Security Code item isn’t displayed in the Menu System.32}

✔

The Security Code function is already activated.

☞ When the Security Code function is activated it isn’t displayed in

the menu items.

? There’s no loudness effect.12

✔

You’re using Non-fading preout.

☞ Loudness has no effect in Non-fading preout.

? The Touch Sensor Tone doesn’t sound.34

✔

The preout jack is being used.

☞ The Touch Sensor Tone can’t be output from the preout jack.

? The Non-fading output can’t be turned ON or OFF.14

✔

The <Switching Preout> (page 28) is set is set on Rear preout.

☞ Change it to Non-fading preout.

— 39 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

? Even though Synchronize Clock is ON, the clock can’t be adjusted.35

? The specified disc does not play, but another one plays instead.52

✔

The received RDS station isn’t sending time data.

✔

The specified CD is quite dirty.

☞ Receive another RDS station.

☞ Clean the CD.

The CD is upside-down.53

☞ Load the CD with the labeled side up.

? The Dimmer function doesn’t work. 38-1

✔

The Dimmer wire isn’t connected correctly.

☞ Check the Dimmer wire connection.

The disc is loaded in a different slot from that specified.54

☞ Eject the disc magazine and check the number for the specified

disc.

? The display color changes subtly. 38-2

✔

This is because thetemperature is different than the temperature

when the setting was done.

✔

The disc is severely scratched.55

☞ Try another disc instead.

☞ The display color condition changes subtly according.to the

ambient temperature.

? The specified track will not play.58

✔

Random play or magazine random play has been selected.

☞ Turn off random play or magazine random play.

Tuner source

? Radio reception is poor.39

? Track repeat, disc repeat, track scan, random play, and magazine

✔

The car antenna is not extended.

random play start by themselves.59

☞ Pull the antenna out all the way.

✔

The setting is not canceled.

☞ The settings for these functions remain on until the setting to off

or the disc ejected, even if the power is turned off or the source

changed.

The antenna control wire is not connected.40

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

? Cannot play CD-R or CD-RW.60

? The desired frequency can’t be entered with the Direct Access

✔

Finalization processing is not being conducted for CD-R/CD-RW.

Tuning.41

☞ Conduct finalization processing with CD recorder.

✔

A station that can’t be received is being entered.

☞ Enter a station that can be received.

✔

A non-compatible CD changer is being used to play the CD-R/CD-

RW.61

☞ Use a CD changer compatible with CD-R/CD-RW to play.

✔

You’re trying to enter a frequency with a 0.01 MHz unit.42

☞ What can be designated in the FM band is to 0.1 MHz.

? A CD ejects as soon as it is loaded.62

? It isn't the set Traffic information sound volume. 43

✔

The CD is upside-down.

✔

The set sound volume is less than the tuner sound volume.

☞ If the tuner sound volume is louder than the set sound volume,the

tuner sound volume is used.

☞ Load the CD with the labeled side up.

✔

The CD is quite dirty.63

☞ Clean the CD, referring to the section on <CD cleaning> (page 5).

Disc source

? Can’t remove disc.64

✔

The cause is that more than 10 minutes has elapsed since the vehicle

? "AUX" is displayed without achieving External disc control mode.50

ACC switch was turned OFF.

✔

O-N switch is set to "O" side.

☞ The disc can only be removed within 10 minutes of the ACC

switch being turned OFF. If more than 10 minutes has elapsed,

turn the ACC switch ON again and press the Eject button.

☞ Set the switch to "N" side.

Unsupported disc changer is connected.51

☞ Connect the supported disc changer. (page 3)

— 40 —

Download from Www.Somanuals.com. All Manuals Search And Download.

? The disc won’t insert.65

? The sound skips when an MP3 is being played.73-1

✔

There’s already another disc inserted.

✔

The media is scratched or dirty.

☞ Press the [0] button and remove the disc.

☞ Clean the media, referring to the section on <CD cleaning> (page

5).

? Direct Track Search and Direct Album Search can’t be done.66-1

✔

The recording condition is bad.73-2

☞ Record the media again or use another media.

✔

Another function is ON.

☞ Turn Random Play or other functions OFF.

? Can't display the ID3 tag information correctly.75

? Track Search can't be done.66-2

✔

Record is not made in conformity with the ID 3 tag version1.x.

✔

For the albums first or last song.

☞ Record in conformity with the ID 3 tag version1.x.

☞ For each album, Track Search can't be done in the backward

direction for the first song or in the forward direction for the last

song.

? Can’t enter Album Select mode.76

✔

There’s no folder recorded in the MP3 media.

☞ Use a media with levels.

MP3 source

? The songs in the selected folder aren’t played in Album Select

? Cannot play an MP3.67

mode.77

✔

Not conforming to ISO 9660 Level 1/2, Joliet, and Romeo.

☞ Use a medium conforming to ISO 9660 Level 1/2, Joliet, and

Romeo.

✔

There are no MP3 in the selected folder.

☞ Make sure there’s recorded content in the MP3 media.

? The MP3 track/album search takes time.78

✔

The MP3 has no or invalid track name extension.68

✔

Many tracks are recorded on the media.

☞ When the media directory is complex, the track/album search can

take time.

☞ Add the ".MP3" extension to the MP3 track name.

The media is scratched or dirty.69

☞ Clean the media, referring to the section on <CD cleaning> (page

? The MP3 related text isn’t displayed correctly.79

5).

✔

A character is entered that this unit can't display.

☞ For the characters that can be used for MP3 text entry, refer to

<Notes on playing MP3> (page 6).

? ^{Noise or no sound generated when an MP3 is played.70}

✔

The track has the MP3 track name extension while it is not an MP3.

☞ Do not use the ".MP3" extension in non-MP3.

? The MP3 track time isn’t displayed correctly.80

☞ There are times when it isn’t displayed correctly according to the

MP3 recording conditions.

? Takes time before the unit starts playing MP3.71

✔

The medium contains many albums, tracks, and hierarchical levels.

☞ The unit checks all tracks on the loaded medium first. If the

medium has many tracks recorded, it may take a long time for the

unit before it starts playing MP3.

If the following situations, consult your nearest service

center:

• Even though the disc changer is connected, the Disc Changer source is

not ON, with "AUX" showing in the display during the Changer Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87,

KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the

Auxiliary input is entered when switching modes.

? Fails to play MP3 in the intended order.72

✔

The MP3 tracks were not written by the CD writer in the order in

which you wanted them to be played.

☞ Depending on the CD writer, you may be able to set the order in

which MP3 tracks are to be played by writing them onto a

medium with their track names beginning with play sequence

numbers such as "01" to "99".

— 41 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

MECHA ER: Something is wrong with the disc magazine. Or the

unit is malfunctioning for some reason.E99

The messages shown below display your systems

condition.

➪ Check the disc magazine. And then press the reset

button on the unit. If the "MECHA ER" code does

not disappear, consult your nearest service center.

EJECT:

No disc magazine has been loaded in the changer.

The disc magazine is not completely loaded.E01

➪ Load the disc magazine properly.

No CD in the unit.

HOLD ER:

The protective circuit in the unit activates when the

temperature inside the automatic disc changer

exceeds 60°C (140°F), stopping all operation.E0d

➪ Cool down the unit by opening the windows or

turning on the air conditioner. As the temperature

falls below 60°C (140°F), the disc will start playing

again.

➪ Insert the CD.

No Disc/NO DISC:

No disc has been loaded in the disc magazine.E02

➪ Load a disc into the disc magazine.

TOC ER:

No disc has been loaded in the disc magazine.E04

➪ Load a disc into the disc magazine.

The CD is quite dirty. The CD is upside-down. The CD

is scratched a lot.

NO NAME:

NO TITLE:

NO TEXT:

Attempted to display DNPS during the CD play having

no disc names preset.E51

Attempted to display the disc title or track title while

the MD having no MD title is being played.E53

➪ Clean the CD and load it correctly.

E-05:

The CD is upside-down.E05

➪ Load the CD correctly.

• Attempted to display the disc text or track text

while the CD having no CD text is being played.E54

• Attempted to display text during reception of the

station that isn't sending text data.E55

BLANK:

Nothing has been recorded on the MD.E10

NO TRACK: No tracks are recorded on the MD, although it has a

• Attempted to display the ID3 tag while the MP3

having no ID3 tag is being played.E52

title.E11

E-15:

Media was played that doesn’t have data recorded

that the unit can play. E15

WAITING:

LOAD:

Radio text data is being received.E56

➪ Use media that has data recorded that the unit can

play.

Discs are being exchanged in the Disc changer.E57

NO ACCESS: After setting it in the Disc Changer, DNPP was done

NO PANEL:

E-77:

The faceplate of the slave unit being connected to

this unit has been removed.E30

➪ Replace it.

without having it been played at least 1 time.E58

IN (Blink):

The CD player section is not operating properly.E59

➪ Reinsert the CD. If the CD cannot be ejected or the

display continues to flash even when the CD has

been properly reinserted, please switch off the

power and consult your nearest service center.

The unit is malfunctioning for some reason.E77

➪ Press the reset button on the unit. If the "E-77"

code does not disappear, consult your nearest

service center.

— 42 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Specifications subject to change without notice.

FM tuner section (KDC-MPV7020/6020/5020)

CD player section

Frequency range (50 kHz space) ..............87.5 MHz – 108.0 MHz

(200 kHz space) ............87.9 MHz – 107.9 MHz

Laser diode....................................................GaAlAs (λ=780 nm)

Digital filter (D/A)......................................8 Times Over Sampling

D/A Converter .......................................................................1 Bit

Spindle speed

Usable sensitivity (S/N = 30dB) ....................9.3dBf (0.8 µV/75 Ω)

Quieting Sensitivity (S/N = 50dB) ...............15.2dBf (1.6 µV/75 Ω)

Frequency response ( 3 dB).................................30 Hz – 15 kHz

Signal to Noise ratio (MONO)..............................................70 dB

Selectivity ( 400 kHz).......................................................≥ 80 dB

Stereo separation (1 kHz) ....................................................40 dB

KDC-MPV7020 ..................................1000 – 400 (CLV 2times)

KDC-6020/5020/5020R.............................500 – 200 rpm (CLV)

Wow & Flutter........................................Below Measurable Limit

Frequency response ( 1 dB).................................10 Hz – 20 kHz

Total harmonic distortion (1 kHz) ......................................0.01 %

Signal to Noise ratio (1 kHz)

AM tuner section (KDC-MPV7020/6020/5020)

Frequency range (9 kHz space) .....................531 kHz – 1611 kHz

(10 kHz space) ...................530 kHz – 1700 kHz

KDC-MPV7020..............................................................105 dB

KDC-6020/5020/5020R ...................................................93 dB

Dynamic range ....................................................................93 dB

Channel separation..............................................................85 dB

MP3 Decode (KDC-MPV7020)

Usable sensitivity (S/N = 20dB) .............................28 dBµ (25 µV)

FM tuner section (KDC-5020R)

Frequency range (50 kHz space) ..............87.5 MHz – 108.0 MHz

Usable sensitivity (S/N = 26dB) .................................0.7 µV/75 Ω

Quieting Sensitivity (S/N = 46dB) ..............................1.6 µV/75 Ω

Frequency response ( 3 dB).................................30 Hz – 15 kHz

Signal to Noise ratio (MONO)..............................................65 dB

Selectivity (DIN) ( 400 kHz)..............................................≥ 80 dB

Stereo separation (1 kHz) ....................................................35 dB

................Compliant with MPEG-1.0/2.0/2.5 Audio Layer-3

Audio section

Maximum output power.................................................50 W x 4

Full Bandwidth Power (at less than 1% THD) ...............22 W x 4

Tone action

Bass : ..............................................................100 Hz 10 dB

Middle : .............................................................1 kHz 10 dB

Treble : ............................................................10 kHz 10 dB

Preout level / Load (during disc play)....................1800 mV/10 kΩ

Preout impedance............................................................≤ 600 Ω

MW tuner section (KDC-5020R)

Frequency range (9 kHz space) .....................531 kHz – 1611 kHz

Usable sensitivity (S/N = 20dB) ...........................................25 µV

LW tuner section (KDC-5020R)

Frequency range .............................................153 kHz – 281 kHz

Usable sensitivity (S/N = 20dB) ...........................................45 µV

General

Operating voltage (11 – 16V allowable) .............................14.4 V

Current consumption.............................................................10 A

Installation Size (W x H x D) .........................182 x 53 x 155 mm

Weight ..............................................................................1.25 kg

— 43 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Indesit Refrigerator RA 24 L User Manual
Intel Computer Hardware BOXDB85FL User Manual
Intermec PDAs Smartphones CN2G User Manual
iOptron Microscope Magnifier ST 80 User Manual
JVC Battery Charger LYT0232 001B User Manual
JVC Camcorder Accessories ABDIONICPKG User Manual
Kenwood Cooktop CP665 User Manual
KitchenAid Blender 5 SPEED ULTRA POWER BLENDER User Manual
KitchenAid Dishwasher KUDE48FXBL0 User Manual
Kompernass Indoor Furnishings KH4102 03 08 V1 User Manual