Kenwood CD Player KDC 416S User Manual

CD-RECEIVER

KDC-416S

KDC-316S

KDC-37MR

KDC-316V

KDC-216S

KDC-116S

INSTRUCTION MANUAL

AMPLI-TUNER-LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

RECEPTOR DE CD

MANUAL DE INSTRUÇÕES

Take the time to read through this instruction manual. Familiarity with installa-

tion and operation procedures will help you obtain the best performance from

your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on

the warranty card, and in the space provided below. Refer to the model and serial

numbers whenever you call upon your KENWOOD dealer for information or service on

the product.

COMPACT

Model KDC-416S/316S/37MR/316V/216S/116S Serial number

DIGITAL AUDIO

Download from Www.Somanuals.com. All Manuals Search And Download.

2Warning

NOTE

2CAUTION

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

Use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous

radiation exposure.

In compliance with Federal Regulations,

following are reproductions of labels on, or

inside the product relating to laser product

safety.

reasonable protection against harmful

interference in a residential installation. This

equipment may cause harmful interference

to radio communications, if it is not installed

and used in accordance with the instructions.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference

by one or more of the following measures:

KENWOOD CORPORATION

2967-3, ISHIKAWA-CHO,

HACHIOJI-SHI

TOKYO, JAPAN

KENWOOD CORP. CERTIFIES THIS EQUIPMENT

CONFORMS TO DHHS REGULATIONS N0.21 CFR

1040. 10, CHAPTER 1, SUBCHAPTER J.

Location : Bottom Panel

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

FCC WARNING

• Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

This equipment may generate or use radio

frequency energy. Changes or modifications

to this equipment may cause harmful

interference unless the modifications are

expressly approved in the instruction manual.

The user could lose the authority to operate

this equipment if an unauthorized change or

modification is made.

NOTE

This Class B digital apparatus complies with

Canadian ICES-003.

— 3 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

IMPORTANT INFORMATION

About the disc changer to be

connected:

To connect a disc changer having the "O-N"

switch to this unit, set the "O-N" switch to

"N".

To connect a disc changer having no "O-N"

switch to this unit, the converter cord CA-

DS100 and/or switching adapter KCA-S210A

are required as options.

If a model with no "O-N" switch is

connected, some unavailable functions and

information that cannot be displayed are

generated, such as the DNPS, DNPP,

Magazine random play, and CD Text display.

Note that none of the KDC-C100, KDC-C302,

C205, C705, and non-Kenwood CD changers

can be connected.

2WARNING

2CAUTION

To prevent injury or fire, take the

following precautions:

•Insert the unit all the way in until it is fully

locked in place. Otherwise it may fall out of

place when jolted.

•When extending the ignition, battery, or

ground wires, make sure to use automotive-

grade wires or other wires with a 0.75mm

(AWG18) or more to prevent wire

deterioration and damage to the wire

coating.

•To prevent a short circuit, never put or leave

any metallic objects (such as coins or metal

tools) inside the unit.

•If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

•Make sure not to get your fingers caught

between the faceplate and the unit.

•Be careful not to drop the unit or subject it

to strong shock.

The unit may break or crack because it

contains glass parts.

•Do not touch the liquid crystal fluid if the

LCD is damaged or broken due to shock.

The liquid crystal fluid may be dangerous to

your health or even fatal.

If the liquid crystal fluid from the LCD

contacts your body or clothing, wash it off

with soap immediately.

To prevent damage to the machine,

take the following precautions:

•Make sure to ground the unit to a negative

12V DC power supply.

•Do not open the top or bottom covers of the

unit.

•Do not install the unit in a spot exposed to

direct sunlight or excessive heat or

humidity. Also avoid places with too much

dust or the possibility of water splashing.

•Do not set the removed faceplate or the

faceplate case in areas exposed to direct

sunlight, excessive heat or humidity. Also

avoid places with too much dust or the

possibility of water splashing.

•To prevent deterioration, do not touch the

terminals of the unit or faceplate with your

fingers.

•Do not subject the faceplate to excessive

shock, as it is a piece of precision

equipment.

•When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

•To prevent a short circuit when replacing a

fuse, first disconnect the wiring harness.

2CAUTION

You can damage both your unit and

the CD changer if you connect them

incorrectly.

Do Not Load 3-in. CDs in the CD slot

If you try to load a 3 in. CD with its adapter

into the unit, the adapter might separate

from the CD and damage the unit.

•Do not place any object between the

faceplate and the unit.

•Do not use your own screws. Use only the

screws provided. If you use the wrong

screws, you could damage the unit.

— 4 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get

dirty, wipe them with a dry, soft cloth.

Cleaning the CD Slot

NOTE

As dust tends to accumulate in the CD slot,

clean it every once in a while. Your CDs can

get scratched if you put them in a dusty CD

slot.

•If you experience problems during

installation, consult your Kenwood dealer.

•If the unit does not seem to be working

right, try pressing the reset button first. If

that does not solve the problem, consult

your Kenwood dealer.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it

with a dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the

stain off with a cloth moistened with neutral

cleaner, then wipe neutral detergent off.

2CAUTION

Applying spray cleaner directly to the unit

may affect its mechanical parts. Wiping the

faceplate with a hard cloth or using a volatile

liquid such as thinner or alcohol may scratch

the surface or erases characters.

Lens Fogging

Reset button

Right after you turn on the car heater in cold

weather, dew or condensation may form on

the lens in the CD player of the unit. Called

lens fogging, CDs may be impossible to play.

In such a situation, remove the disc and wait

for the condensation to evaporate. If the unit

still does not operate normally after a while,

consult your Kenwood dealer.

•Characters in the LCD may become difficult

to read in temperatures below 41 ˚F (5 ˚C).

•The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the

display in the illustrations may differ from

what appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

•The functions that can be used and the

information that can be displayed will differ

depending on the external disc players

being connected.

— 5 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Handling Compact discs

Playing a CD that is dirty, scratched

or warped can cause the sound to

skip and the unit to operate

incorrectly, resulting in worsened

sound quality. Take the following

precautions to prevent your CDs from

getting scratched or damaged.

Storing CDs

Checking New CDs for Burrs

•Do not store CDs in areas exposed to direct

When playing a new CD for the first time,

check that there are not any burrs stuck to

the perimeter of the disc or in the central

hole. CDs with burrs stuck on them may not

load properly or may skip while playing.

Remove burrs using a ballpoint pen or a

similar utensil.

sunlight (such as a car seat or the

dashboard) or other hot places.

A CD-R or CD-RW is more susceptible than

a music CD to damage from high

temperatures and humidity, and in some

cases, may become unusable if left in the

car for long periods of time.

Handling CDs

•Do not touch the recorded side of the CD

(the side opposite the label) when holding

it.

•Remove CDs from the unit when not

listening to them for a while, and put them

back in their cases. Do not pile up CDs that

are removed from their cases or prop them

against something.

Burrs

Cleaning CDs

If a CD has gotten dirty, wipe it off gently

using a commercially available cleaning cloth

or a soft cotton cloth, starting from the

center of the disc and moving outward. Do

not clean CDs with conventional record

cleaners, anti-static formulas, or chemicals

such as paint thinner or benzene.

•The reflective film on a CD-R or a CD-RW is

more fragile than that on an ordinary music CD,

and may peel off if scratched. Fingerprints on a

CD-R or CD-RW are also more likely to cause

skipping when the disc is played. For these

reasons, handle the disc very carefully. Detailed

handling instructions will appear on the CD-R or

CD-RW package: read this information carefully

before using the disc.

•Do not stick tape on either side of the CD.

Tape

— 6 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Do Not Load CD Accessories

Do Not Use Special Shape CDs

Do Not Use CDs with Sticker on the

Labeled Side

Do not use the CD with the label sticker

stuck on it.

Using such a CD may cause the CD to be

deformed and the sticker to peel off,

resulting in malfunction of the unit.

Do not use commercially available CD

accessories that can be loaded into the CD

slot, such as stabilizers, protective sheets,

or CD cleaning discs, since they can cause

the unit to malfunction.

•Be sure to use round shape CDs only for

this unit and do not use any special shape

CDs. Use of special shape CDs may cause

the unit to malfunction.

Removing the CD

Only remove the CD from the machine in a

horizontal direction, holding it flat. You may

damage the surface of the CD if you try

pulling it down as it ejects.

•Be sure to use CDs with disc mark

only for this unit.

•CD-Rs and CD-RWs which have not

undergone finalization processing cannot be

played. (For more information on finalization

processing, refer to the manual for your

CD-R/CD-RW writing software or CD-R/CD-

RW recorder.) Additionally, depending on

the recording status, it may prove

impossible to play certain CDs recorded on

CD-R or CD-RW.

— 7 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Release button

Power

4/¢

Q/AUD

Turning on the power:

Press the SRC (source) button.

NOTE

Turn the power on before carrying out the following procedures.

Turning off the power:

Press the PWR OFF button for at least one second.

FM/

SRC/

PWR OFF

ATT/

LOUD

CLK/

ADJ

Volume

KDC-416S

Increasing Volume:

Press the u button to turn up the volume.

LOUD indicator

Decreasing Volume:

Press the d button to turn down the volume.

ATT indicator

SYSTEM Q indicator

KDC-316S/37MR/316V/216S

ATT indicator LOUD indicator

Attenuator

This function allows you to turn down the volume quickly.

Turning Attenuator On/Off:

Press the ATT button to switch the attenuator on and off.

When the attenuator is on, the ATT indicator blinks.

When the attenuator is off, the volume returns to the original

level.

Clock display

Clock indicator

NOTE

SYSTEM Q indicator

KDC-116S

Turning the volume up, or turning it all the way down deactivates

the attenuator function.

Clock display

LOUD indicator

ATT indicator

Clock indicator

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM Q indicator

— 8 —

Switching Modes

Loudness

This function amplifies low and high tones when the volume is

Switching Modes:

turned down.

Each time you press the SRC (source) button, the mode

switches as follows:

The LOUD indicator lights up when the loudness function is

on.

Turning Loudness On/Off:

Tuner mode

Press the LOUD button for at least one second to switch the

loudness on and off.

CD mode

External disc control mode 1(KDC-416S/316S/37MR/316V only)

External disc control mode 2 / AUX mode

(KDC-416S/316S/37MR /316V only)

Function of the KDC-316S/KDC-37MR/KDC-316V/KDC-216S/KDC-116S

Standby mode

Clock display

Selecting standby mode:

Changing the Clock Display:

Press the SRC button repeatedly and switch to "ALL OFF/OFF".

When "ALL OFF/OFF" is displayed, the standby mode is

activated.

Press the CLK button to switch the clock display on and off.

NOTE

The clock indicator lights while the clock is displayed.

The standby mode turns all functions off while leaving the

power to the unit on. Use this mode when you want to have

the display illuminated but don't want to listen to anything.

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc control mode will differ depending on the unit

that is connected.

• To enable the selection of External disc control mode 2/AUX

mode, you should connect optional switching adapter KCA-

S210A (which allows you to select both External disc control

mode 2 and AUX mode) or CD changer (KDC-CPS87, KDC-

CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) or

switching adapter CA-C1AX (which allows you to select AUX

mode only).

During the AUX mode, "AUX/AVin" will show in the display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

— 9 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Pressing the FM button advances the display, and pressing the

AM button reverses it.

System Q

You can recall the best audio setting preset for different types

of the music.

Fader

Bass

Switching the Preset Sound Setting:

Each time you press the Q button, the preset sound setting

switches as follows:

Middle

Treble

Balance

Scan of Flat – Easy ("SCAN/SCAn")

NOTE

Source tone memory

(Default setting)

Easy ("EASY/SQ-6")

Each source (CD, MD, FM, AM and disc changer) has its own

memory in which to store the bass, middle, and treble tone

settings.

The settings made for a particular source are recalled

automatically whenever you use that source (for example, FM

mode uses the tone settings made for FM, AM for AM, etc.).

Flat ("FLAT/SQ-1")

Jazz ("JAZZ/SQ-5")

Rock ("ROCK/SQ-2")

Pops ("POPS/SQ-4")

Top 40 ("TOP 40/SQ-3")

As you proceed, each indicator would go on.

NOTE

3 Adjust each mode

Press the 4/¢ button.

Look at the table to adjust the mode being displayed.

The System Q function changes the values of the following

sound quality parameters:

Adjustment

mode

Operation of Audio control button

Bass center frequency, bass level, bass quality factor, bass

extend, middle center frequency, middle level, middle quality

factor, treble center frequency, and treble level.

Note that some of these parameters cannot be controlled by the

audio control setting feature.

4 button

Bass decreased.

¢ button

(Display)

Bass ("BAS")

Middle("MID")

Treble("TRE")

Bass increased.

Middle decreased.

Treble decreased.

Left channel emphasized.

Middle increased.

Treble increased.

Their setting values are different depending on the setting of the

mobile preset plan mode.

Balance

Right channel emphasized.

("BAL/BL")

Fader

Rear channel increased.

Front channel increased.

("FAD/FD")

Audio Control Setting

Adjust various parameters of sound quality.

4 Press the AUD to end the control mode.

NOTE

1 Press the AUD button for at least one second to enter the

control mode.

Determining the parameters in the audio control setting would

clear all the adjustments made in the System Q and they are

replaced with the values in the audio control setting.

2 Selecting mode

Press either the FM or AM button.

Each time the button is pressed, the adjustment mode will

change as follows:

— 10 —

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE

Mobile Preset

• The faceplate is a precision piece of equipment and can be

damaged by shocks or jolts. For that reason, keep the faceplate

in its special storage case while detached.

• Do not expose the faceplate or its storage case to direct

sunlight or excessive heat or humidity. Also avoid places with

too much dust or the possibility of water splashing.

This function allows you to adjust the setting that is recalled

with the System Q, according to types of speakers.

1 Press the SRC button repeatedly to select the standby mode.

"ALL OFF/OFF" is displayed when the standby mode is

selected.

Reattaching the Faceplate:

2 Press the Q button to enter the mobile preset plan mode.

1 Align the projections on the unit with the grooves on the

3 Press either the 4 or ¢ button to select the type of

speaker. The setting switches as follows.

faceplate.

Off ("SP OFF/ SP-F") / For the OEM speaker ("SP OEM/ SP-O")

/ For 6/6x9 in. speaker ("SP 6/6x9/ SP-6") / For 5/4 in. speaker

("SP 5/4/ SP-5")

2 Push the faceplate in until it clicks.

The faceplate is locked in place, allowing you to use the unit.

4 Press the Q button to end the mobile preset plan mode.

NOTE

Operation of the KDC-316S/KDC-37MR/KDC-316V/KDC-216S/KDC-116S

Adjusting Time

When you change the setting of type of speaker, the bass,

middle, and treble tone settings are returned to original levels.

Adjust the time.

1 When the clock is not displayed, first press the CLK button to

display the clock.

2 Press the ADJ button for at least two seconds to enter the

Function of the KDC-416S/KDC-316S/KDC-37MR/KDC-316V/KDC-216S

clock adjustment mode. The clock display will blink.

Theft Deterrent Faceplate

The faceplate of the unit can be detached and taken with you,

helping to deter theft.

3 • Adjusting the hours

Press the FM button to advance the hours, or press the AM

button to make the hours go back.

• Adjusting the minutes

Press the ¢ button to advance the minutes, or press the

4 button to make the minutes go back.

Projections

Release button

4 Press the CLK button to end the clock adjustment mode.

NOTE

Grooves

For time adjustment with the KDC-416S, refer to the Manual

Time Adjustment page for the menu settings. (page 20)

Removing the Faceplate:

Press the release button.

The faceplate is unlocked, allowing you to detach it.

— 11 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

Tuner features

Operation of the KDC-316S/KDC-37MR/KDC-316V/KDC-216S

FM/

CRSC

Disabled System Indicator (DSI)

4/¢

A red indicator will blink on the unit after the faceplate is

removed, warning potential thieves. The factory default for

this function is ON.

Turning Disabled System Indicator On/Off:

1 Turn the power of the unit off.

2 While pressing buttons #1 and #3 at the same time, press the

SRC button.

#1-6

SRC

CLK/

Repeat steps 1 and 2 above to turn DSI back on.

NOTE

AUTO/

AME

KDC-416S

The KDC-416S has the equivalent function.

For details, refer to the Disabled System Indicator page for the

menu settings. (page 20)

Band display

Preset station number

Frequency

AUTO indicator

ST indicator

KDC-316S/37MR/316V/216S

ST indicator

Preset station number

CRSC indicator

Band display

AUTO indicator

Frequency

KDC-116S

Band display

Preset station number

CRSC indicator

ST indicator

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTO indicator

Frequency

— 12 —

NOTE

Tuning

The ST indicator lights up when stereo broadcasts are being

received.

You can choose from three tuning modes: auto seek, preset

station seek, and manual. The AUTO 1 indicator lights up

when auto seek tuning is selected, and the AUTO 2 indicator

lights when preset station seek tuning is selected.

Selecting Tuning Mode:

Press the AUTO button.

Station Preset Memory

Store the frequency of a station. You can then recall that

station with a single touch of a button.

Each time you press the AUTO button, the mode switches as

follows.

Auto 1 (Auto Seek Tuning)

1 Select the band/station that you want to have stored.

Auto 2 (Preset Station Seek Tuning)

2 Press the button (#1-6) that you want to use for the station, for

at least two seconds.

Manual (Manual Tuning)

The button number blinks once in the display to indicate that

the data has been stored.

Tuning:

Recalling a Preset Station:

1 Press the SRC (source) button repeatedly to select the tuner

mode. "TUNER/TUnE" is displayed when the tuner mode has

been selected.

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

NOTE

2 Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2 and FM3 (which are used for groups

of preset stations).

You can store six stations in each of the FM1, FM2, FM3, and

AM bands.

Press the AM button to select the AM band.

3 • Auto Seek Tuning

Press the ¢ button to seek higher frequencies.

Press the 4 button to seek lower frequencies.

• Preset station seek tuning

Press the ¢ button to move to the next preset station (i.e.,

the one with the next highest number), and the 4 button to

move to the last preset station (i.e., the one with the next

lowest number).

• Manual Tuning

Press the ¢ button to increase the frequency by one step.

Press the 4 button to decrease the frequency by one step.

— 13 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

The 4 button moves the cursor to the left, and the ¢

Auto Memory Entry

button to the right.

You can automatically store all the receivable frequencies in

the band currently being listened to, and then recall them with

the touch of a button later. This function is especially useful

when you are travelling and do not know what stations are

available. Up to six frequencies can be stored this way.

6 Press the FM or AM button to display the desired character.

Characters that can be displayed are as follows.

Alphabet : A ~ Z

Numerals and symbols : 0~9 @ " ‘ ` % & * + - = , . / \ < > [ ]

7 Continue steps 5 and 6 until all the characters are chosen for

1 Select the band for auto memory entry.

the name.

2 Press the AME button for at least two seconds to start auto

memory entry.

NOTE

You can enter up to eight characters for each name.

The numbers of the preset station buttons are shown in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

8 Assigning Names

Press the MENU button.

The name of the station is stored in memory, and the Station

Name Preset mode ends.

Recalling a Preset Station:

Also, if you make no input for 10 seconds, the name will be

stored up to the point that you have entered, and the mode

ends.

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

NOTE

• You can assign names to up to 18 FM stations and 16 AM

stations.

• All the station names will be erased if you press the Reset

button.

Function of the KDC-416S

Station Name Preset (SNPS)

You can assign names to radio stations with the Station Preset

Memory. Up to 18 FM stations and 16 AM stations can be

assigned names.

• If you want to change the name of a station, first display the

name of the station (following steps 1 to 4 above), then change

the letter(s) that you want by following steps 5 and 6.

1 Adjust the frequency to the station whose name you want to

enter.

2 Enter the menu mode

Press the MENU button for at least one second. "MENU" is

displayed when the menu mode is entered.

Function of the KDC-416S

Switching Display for Tuner

You can change the display used when listening to the radio.

3 Press the FM or AM button to select the display "NAME SET" .

4 Press either the 4 or ¢ button for at least two seconds to

enter the station name preset mode.

Changing the Display:

The cursor will blink in the position where letters are entered.

Each time you press the CLK button, the display changes as

follows:

5 Press either the 4 or ¢ button to move the cursor to the

desired position.

— 14 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/External disc control features

4/¢

Station frequency

SNPS name (only when being preset)

Clock

RDM

SCRL

M.RDM

FM/

SRC

CLK/

REP

SCAN

Operation of the KDC-316S/KDC-37MR/KDC-316V/KDC-216S/KDC-116S

KDC-416S

Clean Reception System Circuit (CRSC)

Track number

Temporarily have reception switched from stereo to mono to

reduce multi-path noise when listening to the FM station.

The factory default for this function is ON.

Turning CRSC On/Off:

Track time

Disc number

Press the CRSC button for at least one second to turn the

function on/off.

IN indicator

The CRSC indicator lights up when CRSC is on.

NOTE

KDC-316S/37MR/316V/216S

Track number

• Strong electrical fields (such as from power lines) may cause

unstable sound quality when CRSC is turned on. In such a

situation, turn it off.

• The KDC-416S has the equivalent function.

For details, refer to the Clean Reception System Circuit page

for the menu settings. (page 20)

SCN indicator

RDM indicator

Disc number

REP indicator

IN indicator

KDC-116S

Track time

Track number

IN indicator

RDM indicator

SCN indicator

REP indicator

Track time

— 15 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/External disc control features

NOTE

Playing CDs

The external disc control mode will differ, depending on the unit

that is connected.

Playing CDs:

If no CDs are inserted, insert one in the slot with the label

facing up.

Mode Display Examples

• "CD2" ...when a CD player is connected

• "DISC" ...when a disc changer is connected

• "DISC-1/CH-1" , "DISC-2/CH-2" ...when two disc changers are

connected

If a CD is already inserted, press the SRC button repeatedly to

select the CD mode.

"CD" is displayed when the CD mode has been selected.

The CD will start playing.

NOTE

The IN indicator lights up when a CD has been inserted.

• When one disc has finished playing its last track, the next disc

in the changer will start playing. When the last disc in the

changer has finished, the player will return to the first disc and

start playing it.

Stopping and Ejecting CDs:

Press the 0 button.

The CD stops playing and ejects from the slot.

2CAUTION

• Disc #10 is displayed as "0".

• Do not attempt to insert a CD into the slot if another one is

already there.

• The unit can only play 5 in. CDs. If you insert a 3 in. CD, it will

get stuck inside and can cause the unit to malfunction.

NOTE

Function of the KDC-416S

Switching Display for Discs

Switch the display that appears while discs are playing.

When you load a CD and eject it right away, the next time you try

to insert the CD may not load. In such a situation, take the CD

out for a moment and then reinsert it.

Switching Display for Discs:

Each time you press the CLK button, the display during disc

play switches as follows:

Function of the KDC-416S/KDC-316S/KDC-37MR/KDC-316V

Track time

Playing Other Disc mode

This function permits the connection of optional players and

the playing of discs other than the loaded CD (in the current

unit).

Disc name (DNPS) (only when being preset)

(Function of disc changers)

Disc title (Units featuring CD text/MD only)

(Function of disc changers)

Playing Discs:

Track title (Units featuring CD text/MD only)

(Function of disc changers)

Press the SRC button repeatedly to select the external disc

control mode.

Clock

The disc will start playing.

— 16 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Play starts at the beginning of the displayed track number.

NOTE

• You can give names to discs through the presetting disc name

function (page 19).

(For disc changers : KDC-416S/316S/37MR/316V only)

Pressing the 4 button while listening to track 1 will only search

back to the beginning of that track. The reverse search is not

"recycled" to the last track on the disc.

Note that depending on the unit, display may not be possible.

• If you try to display the name of a disc that does not have one,

"NO NAME" is displayed instead.

• When there is an attempt to display the title of a disc for which

the disc title/track title has not been recorded, "NO TEXT" is

displayed for CD and "NO TITLE/NO NAME" is displayed for

MD.

• Depending on the type of characters of the CD text, some

characters may not be displayed.

Making a Forward Track Search:

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

Play starts at the beginning of the displayed track number.

NOTE

(For disc changers : KDC-416S/316S/37MR/316V only)

You cannot make a forward track search when listening to the

last track on a disc.

Fast Forwarding and Reversing Disc Play

Fast Forwarding Disc Play:

Hold down on the ¢ button.

Function of the KDC-416S/KDC-316S/KDC-37MR/KDC-316V

Release your finger to play the disc at that point.

Disc Search

(Function of disc changers)

Reversing Disc Play:

Search forward or backward through the discs in a disc

changer.

Hold down on the 4 button.

Release your finger to play the disc at the point.

NOTE

Making a Reverse Disc Search:

You cannot use reverse play between tracks depending on the

model being connected. Instead, the reverse play function is

canceled when it reaches the beginning of a track, at which point

normal play will automatically resume.

Press the AM button to display the desired disc number.

Each time the button is pressed, the displayed disc number

decreases by one.

Play starts at the beginning of the displayed disc.

Making a Forward Disc Search:

Press the FM button to display the desired disc number.

Each time the button is pressed, the displayed disc number

increases by one.

Track Search

Search forward or backward through the tracks on the disc

until you reach the one that you want to listen to.

Play starts at the beginning of the displayed disc.

NOTE

Making a Reverse Track Search:

"LOAD/LOAd" is displayed when discs are being exchanged on

the disc changer.

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current

track, twice to search back to the beginning of the previous

track, and so forth.

— 17 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/External disc control features

Stopping to Listen to the Track Being Scanned:

Press the SCAN button again to stop the scan and keep on

listening to a track normally.

Track / Disc Repeat

Repeat playing the track or the disc currently being listened to.

NOTE

Turning Repeat Play On/Off:

Press the REP button to switch repeat track/disc play on and

off as follows:

• The track scan function is canceled when you eject the disc.

• The track scan function only scans each track on a disc once.

Track Repeat ON

Disc Repeat ON

Random Play

Play all the tracks on the current disc in random order.

(Function of disc changers : KDC-416S/316S/37MR/316V only)

Track/Disc Repeat OFF

1 Press the RDM button to switch random play on and off.

The RDM indicator lights up when random play is turned on.

(KDC-316S/37MR/316V/216S/116S)

The REP indicator lights up when repeat play is turned on.

(KDC-316S/37MR/316V/216S/116S)

The track number blinks in the display when track repeat is on.

The disc number blinks in the display when disc repeat is on.

(KDC-416S/316S/37MR/316V)

"TREP ON"/"REP ON" is displayed and the track number blinks

in the display when track repeat is on. (KDC-416S)

"DREP ON" is displayed and the disc number blinks in the

display when disc repeat is on. (KDC-416S)

"RDM ON" is displayed when random play is turned on. (KDC-

416S)

The track number will change over and over in the display as

the next track is being selected.

When the track has been selected, play will begin.

The selected track number blinks in the display as it is being

played.

NOTE

(For disc changers : KDC-416S/316S/37MR/316V only)

When all the tracks on a certain disc have been played using

random play, the next disc on the changer will start playing using

the same function.

Repeat play is canceled when you eject the disc.

2 To change the track being heard, press the ¢ button.

Another track will be selected and played.

Track Scan

NOTE

Successively play the beginning of each track on a disc until

you find the track that you want to listen to.

Random play is canceled when you eject the disc.

Starting the Track Scan:

Press the SCAN button. The SCN indicator lights up and the

first 10 seconds of each track will be played, in order. (KDC-

316S/37MR/316V/216S/116S)

"SCAN ON"/"TSCN ON" is displayed and the first 10 seconds of

each track will be played, in order. (KDC-416S)

The track number currently being heard blinks in the display.

Function of the KDC-416S/KDC-316S/KDC-37MR/KDC-316V

Magazine Random Play

(Function of disc changers)

Play the tracks on all the discs in the disc changer in random

order.

— 18 —

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Press the M.RDM button to switch magazine random play on

and off.

5 Press either the 4 or ¢ button to move the cursor to the

desired position.

The RDM indicator lights up when magazine random play is

turned on. (KDC-316S/37MR/316V)

The 4 button moves the cursor to the left, and the ¢

button to the right.

"MRDM ON" is displayed when magazine random play is

turned on. (KDC-416S)

The disc and track numbers will change over and over in the

display as the next track is being selected.

When the disc/track has been selected, play will begin.

The selected disc/track number blinks in the display as it is

being played.

6 Press the FM or AM button to display the desired character.

Characters that can be displayed are as follows.

Alphabet (capital letters) : A~Z

Numerals/characters : 0~9 @ " ‘ ` % & * + - = , . / \ < > [ ]

7 Continue steps 5 and 6 until all the characters are chosen for

the name.

NOTE

2 To change the track being heard, press the ¢ button.

Another disc/track will be selected and played.

You can enter up to 8 characters for each name.

NOTE

8 Assigning Names

• Magazine random play is canceled when you eject the disc.

• The time needed for random selection depends on the number

of discs loaded in the disc magazine.

Press the MENU button.

The disc name is stored and the Presetting Disc Names mode

ends.

If you make no entry in a 10-second period, the name will be

stored with the characters input so far.

NOTE

• The number of discs whose names can be stored will differ

depending on the disc changer that is connected. Please see

your disc changer manual for details.

• Discs are identified by their total length and number of tracks. If

another disc happens to have the same specifications as one

that you have already stored a name for, the name will be

displayed for it, too.

Function of the KDC-416S

Presetting Disc Names (DNPS)(Function of disc changers)

Store the names of discs to be displayed when played.

1 Play the disc whose name you want to preset.

NOTE

• If you want to change the name of a disc, repeat steps 1 to 4 to

display the name, and then repeat steps 5 and 6 to enter the

changes.

This function is not available for disc changers that do not feature

the Disc Name Preset function.

2 Enter the menu mode

Press the MENU button for at least one second. "MENU" is

displayed when the menu mode is entered.

3 Press the FM or AM button to select the display "NAME SET" .

4 Press either the 4 or ¢ button for at least two seconds to

enter the disc name preset mode.

The cursor blinks in the position where character input can be

made.

— 19 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu settings

CD/External disc control features

Function of the KDC-416S

4/¢

Text Scroll

(Function of disc changers)

This function permits the text to be scrolled and the entire text

to be displayed. The scrolling method differs depending on the

setting of scrolling in the menu.

To scroll automatically:

Press the CLK button to display the disc title or the track title.

The display of the text will be scrolled repeatedly.

To scroll manually:

1 Press the CLK button to display the disc title or the track title.

2 Pressing the SCRL button results in one scrolling display of the

FM/

titles.

NOTE

• Please see the menu settings (page 20) about switching

between manual scrolling and automatic scrolling.

• Only units with a CD text feature permit title display.

Menu display

— 20 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Display and setting:

Menu System

You can set the defaults for additional functions in the menu

mode. Make a setting for each function, referring to the

following operations.

"BEEP ON" : Beep setting is on. (Default setting)

"BEEP OFF" : Beep setting is off.

NOTE

The beep sound is not output from the preout jacks.

1 Enter the menu mode

Press the MENU button for at least one second.

"MENU" is displayed when the menu mode is entered.

The function that you can adjust is indicated with the current

settings displayed.

Manual Time Adjustment

Adjust the time manually.

2 Selecting function to set

Press the FM button to search through the functions until you

see the one you want to adjust in the display.

Press the AM button to search through the functions

backward.

Display and setting:

1 Select the display "CLK ADJ" during the selecting function in

the menu system.

Function items change in the order of features that follow in

the menu system.

Example: If you want to switch the setting of the touch sensor

tone function from on to off, first search through the

functions until you see "BEEP ON" in the display.

2 Press either the 4 or ¢ button for at least two seconds to

enter the Manual time adjustment mode.

The time display will blink.

3 • Adjusting the hours

Press the FM button to advance the hours, or press the AM

button to make the hours go back.

3 Changing setting for currently displayed function

Press either the 4 or ¢ button.

• Adjusting the minutes

The setting will change for each function.

Press the ¢ button to advance the minutes, or press the

4 button to make the minutes go back.

Example: The setting of the touch sensor tone will switch from

on to off, and "BEEP OFF" is displayed.

4 Press the MENU button to end the Manual Time Adjustment

4 Ending the menu mode

mode.

Press the MENU button.

Exiting the Manual Time Adjustment mode would start the

clock counting.

NOTE

Make sure to end the menu mode when finished.

Touch Sensor Tone

This function produces a beep sound that accompanies button

operation. It can be switched on or off.

— 21 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu settings

Function of the KDC-416S

Disabled System Indicator (DSI)

Name Preset

A red indicator will blink on the unit after the faceplate is

This function allows you to assign the name to be displayed

for the currently receiving radio station or currently playing

disc.

removed, warning potential thieves.

Display and setting:

See the next page for the name presetting method.

"DSI ON" : The disable system indicator is on. (Default setting)

"DSI OFF" : The disable system indicator is off.

Station Name Preset (SNPS) : page 14

Presetting Disc Names (DNPS) : page 19

Clean Reception System Circuit (CRSC)

Temporarily have reception switched from stereo to mono to

reduce multi-path noise when listening to the FM station.

Display and setting:

"CRSC ON" : The CRSC is on. (Default setting)

"CRSC OFF" : The CRSC is off.

NOTE

Strong electrical fields (such as from power lines) may cause

unstable sound quality when CRSC is turned on. In such a

situation, turn it off.

Text Scroll <In External disc control mode>

This function permits the CD text and MD title to be scrolled

and the entire text to be displayed. Switching between manual

scrolling and automatic scrolling is permitted.

Display and setting:

"SCL AUTO" : Automatic scrolling (Default setting)

"SCL MANU" : Manual scrolling

— 22 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations of remote

Accessory of the KDC-316V

NOTE

The supplied remote control unit is in its storage case.

2CAUTION

Do not set the remote on hot places such as above the

dashboard.

Loading and Replacing the Batteries:

Use two "AAA"-size batteries.

SRC

Slide the cover while pressing downwards to remove it as

illustrated.

TUNE /4/TRACK

^TUNE+/¢/TRACK +

FM/DISC +

^{Insert the batteries with the}+ and – ^{poles aligned properly,}

following the illustration inside the case.

ATT

AM/DISC

2WARNING

Store unused batteries out of the reach of children. Contact a

doctor immediately if the battery is accidentally swallowed.

NOTE

• The provided batteries are intended for use in operation

checking, and their service life may be short.

• When the remote controllable distance becomes short, replace

both of the batteries with new ones.

• A portion of the operations may not be possible, depending on

the unit that is connected.

— 23 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations of remote

Accessory of the KDC-316V

Basic operations

Tuner features

• VOLUME buttons

• 4/¢ (TUNE) buttons

Press the + button to turn the volume up.

Press the 4 button to decrease the frequency.

Press the ¢ button to increase the frequency.

Press the – ^{button to turn the volume down.}

• SRC button

• AM/FM buttons

Each time you press the SRC button, the mode switches as

follows:

Press the AM button to select the AM band.

Press the FM button to select and switch between FM1, FM2,

and FM3 bands.

Tuner mode

CD mode

External disc control mode 1

CD/External disc control features

External disc control mode 2 / AUX mode

• 4/¢ buttons

Press the 4 button to search through the tracks backward.

Press the ¢ button to search through the tracks forward.

Standby mode

NOTE

• DISC buttons (for disc changers)

^{Press the DISC}– button to search through the discs backward.

• The mode switches to the next mode from any mode which

cannot be used.

^{Press the DISC}+ button to search through the discs forward.

• The external disc control mode will differ depending on the unit

that is connected.

• 38 button

When a disc is playing, this button pauses the play.

Press the same button again to start play again.

• To enable the selection of External disc control mode 2/AUX

mode, you should connect optional switching adapter KCA-

S210A (which allows you to select both External disc control

mode 2 and AUX mode) or CD changer (KDC-CPS87, KDC-

CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) or

switching adapter CA-C1AX (which allows you to select AUX

mode only).

During the AUX mode, "AVin" will show in the display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

• ATT button

Turns down the volume quickly. To return the volume to its

original level, press the button again. Turning the volume up, or

turning it all the way down deactivates the attenuator function.

— 24 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Installation Procedure

1. To prevent a short circuit, remove the key from the ignition and

External view

Number of items

disconnect the - battery.

2. Make the proper input and output wire connections for each unit.

3. Connect the speaker wires of the wiring harness.

..........................................1

4. Connect the wiring harness wires in the following order: ground,

battery, ignition.

..........................................1

..........................................2

..........................................1

..........................................4

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

2CAUTION

• If your car's ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on and

off with the ignition key. If you connect the ignition wire to a

power source with a constant voltage supply, as with battery

wires, the battery may die.

• If the console has a lid, make sure to install the unit so that the

faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching to

cause a short circuit, then replace the old fuse with one with

the same rating.

• Do not let unconnected wires or terminals touch metal on the

car or anything else conducting electricity. To prevent a short

circuit, do not remove the caps on the ends of the

unconnected wires or the terminals.

..........................................1

• Connect the speaker wires correctly to the terminals to which

they correspond. The unit may be damaged or fail to work if

you share the - wires or ground them to any metal part in the

car.

7...KDC-416S/ 316S/ 316V/ 216S only

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Insulate unconnected wires with vinyl tape or other similar

material.

• Some disc changers need conversion cords for connection. See

the section on "Safety Precautions" for details.

2CAUTION

The use of any accessories except for those provided might

result in damage to the unit. Make sure only to use the

accessories shipped with the unit, as shown above.

• Mount the unit so that the mounting angle is 30° or less.

— 25 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Wires to Terminals

Front right output (Red)

(KDC-416S/316S only)

Front left output (White)

(KDC-416S/316S only)

Rear left output (White)

Rear right output (Red)

Fuse (10A)

FM/AM antenna input

If no connections are made, do not let the

wire come out from the tab.

Wiring harness

(Accessory1)

KENWOOD disc changer control input

(KDC-416S/316S/37MR/316V only)

NOTE

Connect either to the power control

terminal when using the optional

power amplifier, or to the antenna

control terminal in the vehicle.

P.CONT

To connect the Disc changer,

consult your Disc changer manual.

Power control/

Motor antenna control wire

(Blue/White)

ANT

CONT

–

White/Black

White

To front left

speaker

FRONT • L

FRONT • R

REAR • L

Ignition key

switch

Gray/Black

Gray

To front right

speaker

Ignition wire (Red)

ACC

Battery wire (Yellow)

Green/Black

Green

To rear left

speaker

Car fuse box

(Main fuse)

Car fuse box

Ground wire (Black) · (To car chassis)

–

Purple/Black

Purple

To rear right

speaker

–

REAR • R

Battery

2CAUTION

2WARNING

When only two speakers are being connected to the system, connect the

connectors either to both the front output terminals or to both the rear

output terminals (do not mix front and rear). For example, if you connect

the + connector of the left speaker to a front output terminal, do not

connect the - connector to a rear output terminal.

If you connect the ignition wire (red) and the battery

wire (yellow) to the car chassis (ground), you may cause

a short circuit, that in turn may start a fire. Always

connect those wires to the power source running

through the fuse box.

— 26 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Installing in Japanese-Made Cars

Installation

Firewall or metal support

Refer to the section “Removing the hard rubber frame (P. 28)”

and then remove the hard rubber frame.

Align the holes in the unit (two locations on each side) with

the vehicle mounting bracket and secure the unit with the

accessory screws.

Accessory4

8 mm

8mm

MAX.

T/N

ø5mm

Bend the tabs of the

mounting sleeve

with a screwdriver or

similar utensil and

attach it in place.

T: Toyota cars

N: Nissan cars

Accessory5...for Nissan car

Accessory6 ...for Toyota car

Self-tapping

screw

(commercially

available)

Accessory2

Metal mounting

strap

2CAUTION

• During installation, do not use any screws except for those

provided. The use of different screws might result in damage

to the main unit.

• Damage may occur if a screwdriver or similar tool is used with

excessive force during the installations.

NOTE

Make sure that the unit is installed securely in place. If the unit

is unstable, it may malfunction (for example, the sound may

skip).

— 27 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Removing the hard rubber frame

Removing the Unit

Refer to the section “Removing the hard rubber frame” and

Engage the catch pins on the removal tool and remove the

two locks on the lower level.

then remove the hard rubber frame.

Lower the frame and pull it forward as shown in the figure.

Remove the Hex-head screw with integral washer (M4×8) on

the back panel.

Insert the two removal tools deeply into the slots on each

side, as shown.

Catch

Lock

Accessory4

Catch facing up

Accessory3

Removal tool

When the lower level is removed, remove the upper two

locations.

Accessory3

Removal tool

Lower the removal tool

toward the bottom, and

pull out the unit halfway

whilst pressing towards the

inside.

2CAUTION

Be careful to avoid injury from the catch pins on the removal

tool.

NOTE

The frame can be removed from the top side in the same

manner.

Pull the unit all the way out

with your hands, being

careful not to drop it.

— 28 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Screwing the Faceplate on the Unit

Function of the KDC-416S/ 316S/ 316V/ 216S

If you want to fasten the faceplate to the main unit so that it

does not fall off, screw in the provided screw (ø4 × 16 mm) in

the hole shown below.

Accessory7

2CAUTION

Never insert the taptite screw (ø4 × 16 mm) in any other screw

hole than the one specified. If you screw it in another hole, it

will contact and may cause damage to the mechanical parts

inside the unit.

— 29 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring.

Before calling service, first check the following table for possible problems.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the wires, replace the

fuse with one with the same rating.

No sound can be heard, or the

volume is low.

Attenuator is turned on.

Turn off Attenuator.

The fader or balance settings are set all the way to one

side.

Reset the fader or balance settings.

The input/output wires or wiring harness are connected

incorrectly.

Reconnect the input/output wires or the wiring harness

correctly. See the section on "Connecting Wires to

Terminals".

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

Press the reset button on the unit (see p. 5).

One of the speaker wires is being pinched by a screw in

the car.

Check the speaker wiring.

The sound quality is poor or

distorted.

The speakers are not wired correctly.

Reconnect the speaker wires so that each output

terminal is connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull the antenna out all the way.

The antenna control wire is not connected.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

The memory is erased when

the ignition is turned off.

The battery wire has not been connected to the proper

terminal.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

The ignition and battery wire are incorrectly connected.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

A CD ejects as soon as it is

loaded.

The CD is upside-down.

The CD is quite dirty.

Load the CD with the labeled side up.

Clean the CD, referring to the section on "Cleaning CDs"

(see p. 6).

The sound skips on a CD.

A track will not play.

The CD is scratched or dirty.

Clean the CD, referring to the section on "Cleaning CDs"

(see p. 6).

Random play has been selected.

Turn off random play.

— 30 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

PROBLEM

POSSIBLE CAUSE

SOLUTION

Can’t remove disc.

The cause is that more than 10 minutes has elapsed

since the vehicle ACC switch was turned OFF.

The disc can only be removed within 10 minutes of the

ACC switch being turned OFF. If more than 10 minutes

has elapsed, turn the ACC switch ON again and press

the Eject button.

Free switching of the sound

quality.

The System Q function is set on Scan mode.

Refer to the “System Q” page and switch it to a

function other than Scan mode. (see p. 10)

CD/External disc control mode

The disc control mode cannot

be selected.

No wire has been connected to the disc changer input

terminal on the unit.

Connect the wire to the disc changer input terminal on

the unit.

The specified disc does not

play, but another one plays

instead.

The specified CD is quite dirty.

Clean the CD.

The CD is upside-down.

Load the CD with the labeled side up.

The disc is loaded in a different slot from that specified.

Eject the disc magazine and check the number for the

specified disc.

The disc is severely scratched.

Something is touching the disc changer.

The CD is scratched or dirty.

Try another disc instead.

The sound skips.

Remove whatever is touching it.

If skipping happens at the same place when the car is

stopped, something with the CD is wrong. Clean the CD.

The computer chip in the unit is not functioning normally.

Press the reset button on the unit (see p. 5).

The display shows that the

changer is being played, but no

sound can be heard.

The specified track will not

play.

Random play or magazine random play has been

selected.

Turn off random play or magazine random play.

Track repeat, disc repeat, track

scan, random play, and

magazine random play start by

themselves.

The setting is not canceled.

The settings for these functions remain on until the

setting to off or the disc ejected, even if the power is

turned off or the source changed.

Cannot play CD-R or CD-RW.

Finalization processing is not being conducted for CD-

R/CD-RW.

Conduct finalization processing with CD recorder.

A non-compatible CD changer is being used to play the

CD-R/CD-RW.

Use a CD changer compatible with CD-R/CD-RW to play.

— 31 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting Guide

The following messages are displayed when certain problems are occurring in your system. Take the

recommended actions.

No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.

EJECT/E-01

] Load the disc magazine properly.

No CD in the unit.

] Insert the CD.

No disc has been loaded in the disc magazine.

] Load a disc into the disc magazine.

NO DISC/

E-02

No disc has been loaded in the disc magazine.

] Load a disc into the disc magazine.

E-04

The CD is quite dirty. The CD is upside-down. The CD is scratched a lot.

] Clean the CD and load it correctly.

Nothing has been recorded on the MD.

BLANK/E-10

No tracks are recorded on the MD, although it has a title.

NO TRACK/

E-11

The faceplate of the slave unit being connected to this unit has been removed.

] Replace it.

NO PANEL/

E-30

The unit is malfunctioning for some reason.

] Press the reset button on the unit. If the "E- 77" code does not disappear, consult your nearest service center.

E-77

Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.

] Check the disc magazine. And then press the reset button on the unit. If the "E- 99" code does not disappear, consult your

nearest service center.

E-99

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),

stopping all operation.

] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F),

the disc will start playing again.

HOLD/E-0d

If this indicator blinks, the CD player is malfunctioning.

] Eject the CD and try inseting it again.

If the CD cannot be ejected, press the eject button and hold it in until the CD is ejected.

If the following situations, consult your nearest service center:

• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX/AVin" showing in the display during the Changer

Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX

Mode is entered when switching modes.

— 32 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Specifications subject to change without notice.

FM tuner section

Audio section

Frequency range (200 kHz space) ............87.9 MHz – 107.9 MHz

Usable sensitivity (S/N = 30dB) ....................9.3dBf (0.8 µV/75 Ω)

Quieting Sensitivity (S/N = 50dB) ...............15.2dBf (1.6 µV/75 Ω)

Frequency response ( 3.0 dB)..............................30 Hz – 15 kHz

Signal to Noise ratio (MONO)..............................................70 dB

Selectivity ( 400 kHz).......................................................≥ 80 dB

Stereo separation (1 kHz) ....................................................40 dB

Maximum output power.................................................45 W × 4

Full Bandwidth Power (at less than 1% THD) ................22 W × 4

Tone action

Bass : ..........................................................100 Hz 10 dB

Middle : .........................................................1 kHz 10 dB

Treble : ........................................................10 kHz 10 dB

Preout level / Load (during disc play)....................1800 mV/10 kΩ

Preout impedance............................................................≤ 600 Ω

AM tuner section

Frequency range (10 kHz space) ...................530 kHz – 1700 kHz

Usable sensitivity (S/N = 20dB) .............................28 dBµ (25 µV)

General

Operating voltage (11 – 16V allowable) ..............................14.4 V

Current consumption.............................................................10 A

Installation Size (W x H x D) ..........................182 × 53 × 157 mm

7-3/16 × 2-1/16 × 6-3/16 in.

CD player section

Laser diode ....................................................GaAlAs (λ=780 nm)

Digital filter (D/A) .....................................8 Times Over Sampling

D/A Converter .......................................................................1 Bit

Spindle speed ..............................................500 – 200 rpm (CLV)

Wow & Flutter........................................Below Measurable Limit

Frequency response ( 1 dB).................................10 Hz – 20 kHz

Total harmonic distortion (1 kHz) ......................................0.01 %

Signal to Noise ratio (1 kHz) ................................................96 dB

Dynamic range ....................................................................93 dB

Channel separation..............................................................85 dB

Weight.................................................................3.31 lbs (1.5 kg)

— 33 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Ingersoll Rand Heat Pump AF0646SXXXXXX XX X User Manual
Intel Computer Hardware SBC 370 User Manual
Intex Recreation Water Pump 638 User Manual
Invacare Mobility Aid Compass SPT User Manual
JVC Car Stereo System GET0364 002A NJ User Manual
Keating Of Chicago Fryer 24 TS User Manual
Kidco Safety Gate G15d User Manual
KitchenAid Burner KBZU242TSS User Manual
KitchenAid Range KERC500 User Manual
KitchenAid Trash Compactor 9871915B User Manual