MULTIPLE COMPACT DISC PLAYER
DPF-J9030
CD-4900M
INSTRUCTION MANUAL
KENWOOD CORPORATION
This unit is designed for home use only. If the unit is
used in a location other than at home, such as in a
shop (for commercial use), in a car or in a ship, etc.,
and is damaged, a service fee may be charged even
during the warranty period.
This instruction manual is used to describe multiple
models listed above.
Model availability and features (functions) may differ
depending on the country and sales area.
AP
B60-4465-08 00 (K, T)
9909
Download from Www.Somanuals.com. All Manuals Search And Download.
Your New Kenwood 200-Disc CD Changer
Welcome to your new Kenwood 200-Disc CD Changer.
3
CD-4900M is sold in USA. DPF-J9030 is sold in other countries.
This CD changer offers the following exciting features :
÷ 200-disc capacity
Chapter1
÷ 10-key remote and infrared remote keyboard
÷ Digital audio output
÷ CD Text, which displays text from encoded CDs on the unit’s display.
÷ Disc and Track Naming, which allows you to program your own names for discs and tracks.
÷ Music Type File, which lets you organize your discs into specific musical types (such as Classical, Jazz,
Rock), and then play them by type.
÷ Dual disc transport mechanisms (2 CD players)
÷ Continuous Single-Zone Playback, which uses both the changer’s players to play all discs or tracks
Chapter2
continually, without interruption.
÷ Simultaneous Dual-Zone Playback, which plays 2 different CDs in 2 rooms at once when used with a
Kenwood Dual-Zone/Dual-Source receiver.
Your new changer can play the following disc types :
÷ Standard 12 cm CDs
÷ CDV (Video) and CDG (Graphics), although it will not display the video portion
You may not play 8 cm CD “singles.”
Chapter3
Unpacking
Unpack your new CD changer carefully and make sure that all the accessories are present:
If any accessories are missing, or if the changer is damaged or fails to operate, notify your dealer immediately. If your
changer was shipped to you directly, notify your shipper immediately. Kenwood recommends that you retain the
original carton and packing materials in case you need to move or ship the changer in the future.
Chapter4
Keep this manual handy for future reference.
Accessories
System control cable ...... (1)
Audio cables.................... (2)
10-key Remote................ (1)
Communication cable ..... (1)
Batteries (R6/AA) ............ (4)
Chapter5
Infrared Remote Keyboard ...... (1)
REMOTE CNTROL UNIT RC-KB2
POWER
CONFIRM
BEST
SEL.
REPEAT
RANDOM
DISPLAY
TITLE
INPUT
USER
FILE
NAME
+10
+100
7
6
4
¢
1
¡
(
9
)
0
DELETE
!
1
@
2
#
3
$
4
%
5
^
6
&
7
✱
8
-
+
=
DISC
SEL
P
.MODE
CHECK
CLEAR
Q
A
W
E
R
T
Y
U
I
O
P
,
,,
,
ENTER
SET
MODE
:
;
S
D
F
G
H
J
K
L
SHIFT
<
,
>
.
SHIFT
Z
X
C
V
B
N
M
?
/
ROOM
B
CONT
PLA
SUB
OUT
SPACE
CURSOR
L
CURSOR
R
CHARAC.
SRCH
DOWN
CHARAC.
SRCH
UP
DISC
DISC
SKIP
UP
ROOM
B
Y
SKIP
MONIT
.
DOWN
Chapter6
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Caution : Read the pages marked
carefully to ensure safe operation.
4
Before applying power ............................................... 2
Safety precautions .....................................................2
Your New Kenwood 200-Disc CD Changer ................ 3
Chapter 1 : Setting Up Your New CD Changer ........... 5
Connecting to a Receiver or Amplifier ................................ 6
System Control Chaining ........................................................ 8
Setting Up the 10-Key Remote and Keyboard .................... 9
10-Key Remote ..........................................................9
Keyboard ....................................................................9
Chapter 4 : Specifying and Using Disc or Track Data .. 29
Registration of Title ............................................................... 30
AssigningTitle (TITLE INPUT mode) ....................30
To change or delete a title .....................................32
Listening to music by genre (MUSIC TYPE mode) .............. 33
Registration of music type (MUSIC TYPE SET mode)
...................................................................................33
Registration of user's disc file (USER FILE SET mode)
...................................................................................34
Playing the music type or user file
Cahpter1
Chapter 2 : Getting to know Your New CD Changer...... 10
Front Panel .............................................................................. 11
Front Panel Displays ...............................................12
10-Key Remote and Keyboard ............................................. 13
10-Key Remote ........................................................13
Keyboard ..................................................................14
Cahpter2
(MUSIC TYPE PLAY mode) (Player A only) ..........35
Disc search (DISC SEARCH mode) (Player A only) .................. 36
Searching a disc by the disc title
(CHARAC. SEARCH mode) .....................................36
Searching the music type or user file
Chapter 3 : Loading and Playing Discs ..................... 16
Preparation ............................................................................. 17
Loading discs in the carousel ................................17
Normal play (TRACK mode) ................................................. 19
Playing tracks in order from track No.1 ...............19
Playback from desired track ..................................21
Repeated playback (REPEAT mode)................................... 22
Playback in a random order (RANDOM mode) ............... 23
Programming tracks in desired order
(M.TYPE SEARCH mode) ........................................37
Listening to your favorite titles
(BEST SELECTION mode) (Player A only) ....................................... 38
Registration of best selection file .........................38
Playing the best selection file ...............................38
Cahpter3
Chapter 5 : Dual-Zone Capabilities........................ 40
Chapter 6 : In case of difficulty............................... 41
In case of difficulty................................................................ 41
Important items ...................................................................... 42
Cahpter4
(PGM mode) (Player A only) ...................................................24
Continuous playback ............................................................ 26
Timer operation (Player A only) .......................................... 27
Registration of DTS discs..................................................... 28
Chapter 7 : Warnings and Specifications............. 43
Warnings ................................................................................. 43
Specifications ........................................................................ 43
Cahpter5
Cahpter6
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 : Setting Up Your New CD Changer
5
Welcome to the Kenwood CD-4900M/DPF-J9030 Instruction manual.
The Instruction manual contains all the information you need to know to set up and operate your new CD changer safely and enjoy-
ably.
This chapter guides you through the connection and setup of your new CD changer and its remote.
Chapter1
Refer to the following pages for details on these issues :
÷ Connecting to a Receiver or Amplifier
÷ System Control Chaining
÷ Setting Up the 10-Key Remote and Keyboard
6
8
9
Your CD changer includes a standard remote and a remote keyboard (for easier text entry). You can use
either device to control the changer. For the sake of simplicity, this manual provides standard remote
instructions for all functions except text entry.
Chapter2
Before You Begin
Be sure to read the notes on this page before you begin setting up the changer.
NNootteess
Chapter3
1. All cables (except the digital optical cable) should have been supplied with your new CD changer.
see “Unpacking”
3
If you need to purchase additional or replacement cables, visit any home electronics store or the Kenwood USA Web site at
2. Do not plug in the CD changer’s power cord until you have finished making connections to your receiver or amplifier.
3. If you exposed your changer to a great difference in temperature (for example, if you purchased it in winter from a store with
an unheated warehouse) or if the humidity in the room changes, condensation may form inside the unit. If this occurs, connect
the unit, turn it on, and leave it on but unused for a few hours. This will evaporate the condensation and return your changer to
working order. Restart the changer before using it again.
Chapter4
4. Clean your CD changer with a soft, dry cloth. Avoid solvents of any kind, as they may damage the cabinet components.
5. Do not use CD accessories such as protection sheets or disc cleaners with your new CD changer.
6. Kenwood recommends having your CD changer’s precision optical pickup inspected periodically. Depending on the operation
environment (humidity, dust, smoke, etc.), this pickup should operate approximately 1,000 hours before requiring inspection. To
schedule inspection, consult the store where you purchased the changer or visit the Kenwood USA Web site’s Support area.
Chapter5
7. Only player A supports DTS playback.
8. Be sure to locate your changer on a level and stationary surface, or it will not be able to play discs properly.
9. Your CD changer continues to store the following information for at least 3 weeks after you unplug its power cord:
÷ Power status (on or off)
÷ Disc and track names
÷ Music Type assignments
÷ User File assignments
÷ Best Selection assignments
÷ DTS assignments
Chapter6
After that you must reset this information according to the instructions in this manual.
q
10. Once you have set up the changer and loaded discs, you should not move it without doing the following:
(1) Remove all the discs from the unit and close the disc door.
(2) Look at the display(s). “NO DISC” should appear steadily (i.e., it should not be flashing).
(3) Turn off the CD changer.
(4) A few seconds after the display appears, disconnect the CD changer from the receiver and unplug the CD changer from the
wall outlet or power strip.
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Receiver or Amplifier
Make connections as shown below.
DIGITAL OUT jack (OPTICAL)
Remove the protective cap before using the DIGITAL
When connecting the related system components, refer
also to the instruction manuals of the related components.
Do not plug in the power lead until all connections are com-
6
OUT jack.
DIGITAL
OUT
pleted.
Digital component (MD,DAT, etc.)
OPTICAL
TEXT
Remove the cap
DIGITAL INPUT (OPTICAL)
Optical digital cable
(Commercially-available)
Cahpter1
SYSTEM SL16
CONTROL TEXT
DIGITAL
OUT
OUTPUT
*1
L
OPTICAL
TEXT
R
A
B
*2
To wall AC
outlet
Cahpter2
Communica-
tion cable
System
control
cable
Optical digital cable
(Commercially-available)
Cahpter3
Audio
cable
SYSTEM
CONTROL
OPTICAL
TEXT
Audio
cable
Cahpter4
CD1
CD2
* 1
Cahpter5
OUTPUT A:
Analog output from Player A.
OUTPUT B:
Analog output from Player B.
Receiver or Amplifier, etc.
* 2
DTS Disclaimer clause
Note on the SL-16 TEXT jack
When playing DTS-encoded CDs, excessive noise will be ex-
hibited from the analog stereo outputs. To avoid possible
damage to the audio system, the consumer should take proper
precautions when the analog stereo outputs of the CD player
is connected to an amplification system.To enjoy DTS Digital
Surround™ playback, an external 5.1 channel DTS Digital Sur-
round™ decoder system must be connected to the digital out-
put (S/P DIF, AES/EBU, or TosLink) of the CD player.
When using a KENWOOD Receiver equipped with the SL-16 TEXT
jack, connect it to the Receiver using the communication cable
provided with this unit. This makes it possible to display the
disc and track titles on the LCD remote control unit (provided
with the Receiver).
Cahpter6
If your receiver has the SL16/XS8 mode select switch,
set the connected receiver to the [SL16] mode.
NNoottee
1. Connect all cables firmly. If connections are loose, there could be loss of sound or noise produced.
2. When plugging and unplugging connection cables, be sure to first remove the power cable from the AC outlet. Plugging/unplugging
connection cables without removal of the power cable can cause malfunctions or damage to the unit.
Cahpter7
NNootteess
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Receiver or Amplifier
7
To Connect the Changer to a Kenwood Receiver
1.Unplug the receiver from the wall outlet or power strip.
Chapter1
2.Connect the audio cable from output A on the CD changer to the receiver as shown to the left. If you are connecting
the CD changer to a receiver that supports Dual-Zone/Dual-Source listening (such as the VR-4900/KRF-V9993D
shown in the illustration), connect audio cables for both outputs A and B to the appropriate jacks on the receiver.
3.Connect an optional optical digital cable from the changer to the receiver as shown to the left. If your receiver does
not support digital output, skip this step.
If you do not connect a digital cable or if your receiver does not support digital output and DTS decoding, DTS discs
do not play on your changer.
Chapter2
4.Connect the system control cable from the changer to the receiver jack as shown to the left. If your receiver has the
SL16/XS8 mode select switch, set the connected receiver to the [SL16] mode. If you are connecting more than one
Kenwood device with a system control cable, see “What if I Have Several Kenwood Devices ?” for more information.
8
5.Connect the SL16 text cable (Communication cable) from the changer to the receiver’s jack as shown to the left.
6.Plug the changer’s power cable into a wall outlet or power strip.
Chapter3
7.Plug the receiver’s power cord back into a wall outlet or power strip.
To Connect the Changer to a Non-Kenwood Receiver or Preamplifier
1. Unplug the receiver or preamplifier from the wall outlet or power strip.
2. Connect the audio cable(s) from output A on the CD changer to the receiver or preamplifier as shown to the left.
3. Connect an optional optical digital cable from the changer to the receiver or preamplifier as shown to the left. If your
receiver does not support digital output and DTS decoding, skip this step. If you do not connect a digital cable or if your
receiver does not support digital output, DTS discs do not play on your changer.
Chapter4
4. Plug the changer’s power cable into a wall outlet or power strip.
5. Plug the receiver’s power cable back into a wall outlet or power strip.
To Connect the Digital Output Directly to a Digital Recorder (MD, DAT, etc.)
Chapter5
If your receiver does not support digital output, but you want to record discs to a digital format, you can connect the CD changer
directly to a digital recording device, such as an MD or DAT recorder.
1. Unplug the digital recorder from the wall outlet or power strip.
2. Connect the digital cable from the changer to the recorder.
3. Plug the changer’s power cable into a wall outlet or power strip.
4. Plug the recorder’s power cable back into a wall outlet or power strip.
Chapter6
Malfunction of microcomputer
If operation is not possible or erroneous display appears even though all connections have been made properly, reset the microcomputer
referring to “In case of difficulty”.
q
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
System Control Chaining
What if I Have Several Kenwood Devices ?
8
System control allows you to :
÷ control connected devices via the receiver’s remote control
÷ switch the receiver’s input automatically to a connected device when you start playback from that device
÷ synchronize recording a CD or MD automatically when you start playback from those connected devices
Receiver or Amplifier
SYSTEM
CONTROL
Cahpter1
This unit
SYSTEM
CONTROL
This unit is compatible only with the [SL16] mode. The system
control operation is not available if the unit is connected in the
[XS-8] connection mode.
÷You can connect the system control cord to either system control
Cassette deck or MD
Cahpter2
jack of the unit.
SYSTEM
CONTROL
÷If your component has the mode select switch, set the connected
components to the [SL16] mode.
(Ensure that the power plug is not connected.)
1. If your amplifier or receiver does not support system control, do not connect the system control cable to any device.
2. Some CD players and cassette decks do not support the SL16 system control mode. Do not include these devices in a set of SL16 chained
connections.
NNootteess
Cahpter3
3. Do not connect system control cables to any device not specified by Kenwood. Using system control functions with a device that does not
support them can damage the device.
4. Make sure system control plugs are firmly seated in the appropriate jacks.
Cahpter4
Cahpter5
Cahpter6
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the 10-key Remote and Keyboard
10-key Remote
9
To load Batteries
3Close the cover.
1Remove the cover.
2Insert two AA batteries.
Chapter1
÷Insert two AA-size (R6) batteries as
indicated by the polarity marking.
Chapter2
The 10-key remote operates in the following range:
Infrared Remote Sensor
Remote Operating Range
If you use the remote outside of this range, the remote will not
operate correctly. As you use the remote, be aware of the following:
PUSH OPEN
)
TIMER PLAY
OFF
ON
^
&
D
I
S
C
SKIP
STANDBY
÷The batteries that came with your new CD changer are intended to
be used for operation checks and setup. Therefore, they may not
last as long as ordinary batteries. Consider replacing them as soon
as you have verified that the remote operates correctly.
÷When the remote’s operating range gets shorter, replace both
batteries.
DISPLAY
RANDOM
CONFIRM
REPEAT
CONTINUOUS PLAY
DISPLAY
POWER
ON/STANDBY
$
›
6 m (20 ft.)
30°
30°
Chapter3
CONTINUOUS SUB OUT
÷Do not install the CD changer where direct sunlight or high-fre-
quency fluorescent lighting can shine directly into the remote
sensor. This can decrease the operating range of your remote.
÷When pressing more than one remote control key successively,
press the keys securely by leaving an interval of 1 second or more
between keys.
CONFIRM
A
PLAY
MONITOR
POWER
B
C
BEST
SELECTION. REPEAT
RANDOM
F
DISPLAY
G
Infrared Remote
transmitter
D
E
1
2
I
3
4
H
J
K
5
6
7
8
L
M
N
O
9
0
+10
R
+100
S
P
Q
–
T
.
/
'
W
U
V
DISC
SELECTOR.
(
)
MODE
SET
X
Y
Z
DELETE
/CLEAR
SPACE
/CHECK
CHARAC.
/P.MODE
DISC SKIP
DOWN
UP
ENTER
7
6
CURSOR
CHARACTER
UP
LEFT
RIGHT
DOWN
1
¡
4
¢
REMOTE CONTROL UNIT
RC-P0713
Chapter4
Keyboard
To load Batteries
1Remove the cover.
2Insert two AA batteries.
3Close the cover.
Chapter5
÷Insert two AA-size (R6) batteries as
indicated by the polarity marking.
Chapter6
The keyboard operates in the following range:
Infrared Remote Sensor
Keyboard Operating Range
If you use the remote outside of this range, the remote will not
operate correctly.
PUSH OPEN
)
As you use the remote, be aware of the following:
TIMER PLAY
÷The batteries that came with your new CD changer are intended to
be used for operation checks and setup. Therefore, they may not
last as long as ordinary batteries. Consider replacing them as soon
as you have verified that the keyboard operates correctly.
÷When the remote’s operating range gets shorter, replace both
batteries.
OFF
ON
^
&
D
I
S
C
SKIP
STANDBY
DISPLAY
RANDOM
CONFIRM
REPEAT
CONTINUOUS PLAY
DISPLAY
POWER
ON/STANDBY
$
›
3 m (10 ft.)
30°
30°
Chapter7
REMOTE CONTROL UNIT R-KB2
÷Do not install the CD changer where direct sunlight or high-fre-
quency fluorescent lighting can shine directly into the remote
sensor. This can decrease the operating range of your keyboard.
÷When pressing more than one remote control key successively,
press the keys securely by leaving an interval of 1 second or more
between keys.
Infrared Remote
keyboard
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 : Getting to know Your New CD Changer
Your new CD changer contains the following sophisticated features :
10
÷An easy-to-use front panel, remote and keyboard
See “Front Panel”
See “10-key Remote”
See “Keyboard”
!
#
$
÷Multiple front panel display format that allow you to view detailed information about the disc currently
Cahpter1
playing
See “Front Panel Displays”
@
Your CD changer includes a standard remote and a remote keyboard (for easier text entry).
You can use either device to control the changer. For the sake of simplicity, this manual provides stan-
dard remote instructions for all functions except text entry.
Cahpter2
Cahpter3
Cahpter4
Cahpter5
Cahpter6
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
11
(The displays given in this manual are approximations only. They may differ
from what actually appears on the display.)
Play indicator
Text information display
••• •• •• •••• •• ••
Chapter1
Pause indicator
DISPLAY
Chapter2
1
1
2
3
4
5
6
7 8 9 0 ! @
#
PUSH OPEN
)
TIMER PLAY
Chapter3
OFF
ON
DISPLAY
|
DISPLAY
A
|
^
&
DISC SKIP
B
STANDBY
STANDBY
POWER
OPERATION
CONFIRM
REPEAT
CONTINUOUS PLAY
DISPLAY
RANDOM
$
›
ON/STANDBY
ON/STANDBY
Chapter4
$
%
^ &
1 POWER button/STANDBY indicator (For U.S.A.)
0 REPEAT button
button/STANDBY indicator (For other countries)
! Play/Pause (6) button
@ Remote sensor
2 TIMER PLAY switch
3 Player B display
4 Disc door
Chapter5
# Stop (7) button
$ LCD remote transmitter
The disc and track title data are output to the LCD remote control
unit (provided with a KENWOOD Receiver or optional) through this
window.
5 RANDOM button
6 OPERATION A-B button
7 Player A display
% DISPLAY button
^ CONTINUOUS PLAY button
Chapter6
8 DISC SKIP knob
Used for disc selection. Characters are selected at the time of
character input.
& Track skip button (4, ¢)
Press to skip to the beginning of another track.
Characters are selected at the time of title registration.
9 CONFIRM button
Chapter7
Standby mode
While the standby indicator of the unit is lit, a small amount of current is flowing into the unit’s internal circuitry to back up the memory. This condition is
referred to as the standby mode of the unit. While the unit is in the standby mode, it can be turned ON from the remote control unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
FrontPanel
12
Front Panel Displays
Your CD changer’s front panel has one display for each player it contains. These displays show information about the disc or
track currently being played. Since some of the text information may be longer than can be displayed on one line, the text
information scrolls, if necessary.
Basic Info/Time Info
This display shows basic information like disc and track numbers as well as disc and track-specific time information (elapsed and remaining).
To change the display :
Cahpter1
1. Choose a player A or B.
*
2. Press the DISPLAY button on the front panel, remote, or the keyboard until the information you want appears.
The panel display shows the following:
1 Track title display (if the CD contains encoded title data or if you have entered title data)
CONCERTONINSDCT
2 Disc number/Track number display (the default if there is no title information)
DISC123 TRACK01
3 Disc title display (if the CD contains encoded title data or if you have entered title data)
Cahpter2
LOVEELOVEILOVET
4 Elapsed time of current track
Disc #
Track #
Time
During Stop
During Play
D123E100NIN2:37
5 Remaining time of current track
÷In the TRACK mode, MUSIC TYPE ÷In the TRACK mode, information is
C
mode, information is displayed in
displayed in order of 1, 2, 3, 4,
order of 3, 2 then 4.
5, 6 then 7.
Disc #
Track #
Time
÷In the PGM mode, information is ÷In the PGM mode, RANDOM
displayed in order of 1, 2, 3 then
4.
mode, MUSIC TYPE mode and
BEST SELECTION mode, infor-
mation is displayed in order of 1,
2, 3, 4 then 5.
D123E100NI-1:23
6 Elapsed time of current disc
Disc # Track #
Time
D123E100-36:25T
7 Remaining time of current disc
Cahpter4
Disc #
Track #
Time
D123E100-23:45T
Complete CD-Text Info (Player A only)
In the case of a CD-TEXT disc, the text information shown below is displayed automatically during normal play (TRACK mode).
To view complete text information :
1. Press MODE button on the remote or keyboard.
2. Use DISC SKIP (DOWN/UP) button on the remote or keyboard to select “ALL INFORMATION”.
Cahpter5
3. Press SET button on the remote or keyboard. The display cycles through the following:
1 Disc/Track Title
2 Disc/Track Artist
3 Disc/Track Songwriter
4 Disc/Track Composer
5 Disc/Track Arranger
6 Disc/Track Message (such as a message from a sponsor or artist)
7 ID INFO. (such as record company, release date, etc.)
8 Genre INFO.
Cahpter6
÷Items from 1 to 6 are displayed in the sequence of disc and track.
÷If there is no information for any given area, the panel displays “-----”. If the disc does not have factory-encoded CD Text disc or track information,
“NO CD TEXT” appears for 3 seconds.
To view the next or previous information item, use DISC SKIP (DOWN/UP) button on the remote or keyboard.
To skip tracks, use Skip (4,¢)(DOWN/UP) button on the remote or keyboard.
To stop viewing text information, press MODE button on the remote or keyboard.
Cahpter7
With a CD-TEXT disc, disc and track titles can be displayed without the limit on the number of characters when “ALL INFORMATION” is set.
The disc and track titles are also displayed without the limit on the number of characters during playback or loading of a CD-TEXT disc.
NNoottee
Download from Www.Somanuals.com. All Manuals Search And Download.
10-key Remote and Keyboard
All operations can be controlled from both the 10-Key Remote and Keyboard remote control units.
13
10-key Remote
The buttons with the same name as those on the main unit operate the same way as on the main unit.
The buttons marked * are provided only on the remote control unit. The remote control unit controls Player A regardless of whether the OPERATION A-
B indicator on the main unit is lit or not.
Chapter1
1POWER (
)
2Buttons for modes, display control and letters
÷CONFIRM
÷CONTINUOUS PLAY
CONTINUOUS SUB OUT
PLAY
MONITOR
CONFIRM
A
POWER
B
C
÷SUB OUT MONITOR *
1
2
BEST
SELECTION REPEAT
RANDOM
DISPLAY
G
Used to monitor the audio played on Player B.
D
E
F
÷BEST SELECTION *
Chapter2
1
2
I
3
4
H
J
K
Used for best selection registration and playback.
5
6
7
8
5
6
÷REPEAT
÷RANDOM
÷DISPLAY
L
M
N
O
9
0
+10
R
+100
S
P
Q
.
/
–
T
'
W
3
4
U
V
DISC
(
)
SELECTOR
MODE
SET
3Buttons for selecting discs and entering special characters
X
Y
Z
÷DISC SELECTOR *
DELETE
/CLEAR
SPACE
CHARAC.
P.MODE
/CHECK
Press to select a disc number.
DISC SKIP
Chapter3
DOWN
UP
ENTER
÷Letter/special character buttons *
7
6
Used for selection of disc numbers, as well as for character input.
CURSOR
CHARACTER
DOWN
LEFT
RIGHT
UP
1
4
¢
¡
4Buttons for basic operation
÷Stop (7)
REMOTE CONTROL UNIT
RC-P0713
÷ENTER/Play/Pause (6)
÷Search (1, ¡), CURSOR (LEFT/RIGHT) *
Press to move the played position of disc at high speed. Used as cursor buttons at the time
of character input.
Chapter4
÷Skip (4,¢), CHARACTER (DOWN/UP)
Model : RC-P0713
(Player A only)
Infrared ray system
5Buttons for entering numbers and letters *
Used for selection of disc numbers and track numbers, as well as for character input.
6Buttons for programming and data entry
÷MODE *
Chapter5
Press to switch the mode.
÷DELETE/CLEAR *
Usedtodeletetheenteredcontents. Atthetimeofcharacterinput, charactersaredeleted.
÷SPACE/CHECK *
Used to confirm the entered contents. Inserts a space at the time of character input.
÷CHARAC./P. MODE *
Used for playback mode switching. At the time of character input, this button switches
between capital letters/small letters/numbers and special characters.
÷SET *
Chapter6
Used for confirmation of mode settings. At the time of character input, one character is
confirmed and the cursor goes to the next digit.
÷DISC SKIP (DOWN/UP)
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
10-keyRemoteandKeyboard
14
Keyboard
The buttons with the same name as those on the main unit operate the same way as on the main unit.
The buttons marked * are provided only on the remote control unit.
Buttons masked with
are not used with this unit.
You can use the keyboard to control both players. To control Player A, press the keyboard buttons as normal.
To control Player B, hold down while ROOM B button pressing the keyboard buttons you need.
7
3
Cahpter1
2
4
REMOTE CONTROL UNIT RC-KB2
POWER
CONFIRM
BEST
SEL.
REPEAT
RANDOM
DISPLAY
TITLE
INPUT
USER
FILE
NAME
+10
+100
7
6
4
¢
1
¡
5
1
DELETE
(
9
)
0
!
1
@
2
#
3
$
4
%
5
^
6
&
7
✱
8
-
+
=
DISC
SEL.
CHECK
CLEAR
P.MODE
Q
A
W
E
R
T
Y
U
I
O
P
,
3
Adjust the keyboard
height as required.
,,
,
ENTER
SET
MODE
:
;
S
D
F
G
H
J
K
L
Cahpter2
6
SHIFT
SHIFT
<
,
>
.
?
Z
X
C
V
B
N
M
/
6
ROOM
B
CONT
PLAY
SUB
OUT
CURSOR
L
CURSOR
R
CHARAC.
SRCH
DOWN
CHARAC.
SRCH
UP
DISC
DISC
SKIP
UP
ROOM
B
SPACE
SKIP
MONIT.
DOWN
8
3
4
8
2
Model : RC-KB2
Infrared ray system
Cahpter3
Buttons inside
are those for use with ROOM B.
1Input buttons for numbers and letters *
Used for selection of disc numbers and track numbers, as well as
for character input.
5POWER (
)
6Buttons related to program and file registration
÷ 0~9 *
÷ MODE *
Press to switch the mode.
2Buttons related to playback mode and display
÷ SET *
Cahpter4
Used for confirmation of mode settings. At the time of character
input, one character is confirmed and the cursor goes to the next
digit.
÷ CONFIRM
÷ CONT PLAY
÷ SUB OUT MONIT. *
÷ ENTER *
Used to monitor the audio played on player B.
Used for title confirmation.
÷ BEST SEL. *
÷ SHIFT *
Used for best selection registration and playback.
(This button is provided only on the Keyboard.)
At the time of character input, this button switches between
capital letters/small letters/numbers and special characters.
÷ REPEAT
÷ RANDOM
÷ DISPLAY
Cahpter5
÷ P.MODE *
Used for playback mode switching.
÷ CHECK *
3Disc selection buttons
÷ +10 *
÷ +100 *
Used to confirm the entered contents.
÷ SPACE *
Inserts a space at the time of character input.
÷ DISC SEL. *
÷ DELETE *
Press to select a disc number.
At the time of character input, characters are deleted.
÷ DISC SKIP (DOWN/UP)
÷ CLEAR *
Cahpter6
Used to delete the entered contents.
4Buttons for basic operation and character input
÷ Stop (7)
÷ Play/Pause (6)
7Shortcut button to the TITLE INPUT mode
(This button is provided only on the Keyboard.)
÷ TITLE INPUT *
÷ Skip (4, ¢)
÷ Search (1, ¡) *
8ROOM B *
(This button is provided only on the Keyboard.)
Press when controlling Player B.
Press to move the played position of disc at high speed.
÷ CHARAC. SRCH UP/DOWN *
Characters are selected at the time of character input.
Cahpter7
÷ CURSOR (L/R) *
Used as cursor buttons at the time of character input.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Chapter1
Chapter2
Chapter3
Chapter4
Chapter5
Chapter6
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 : Loading and Playing Discs
Your new CD changer contains a disc carousel that can store and play up to 200 discs using any
of the following methods :
16
÷ Normal Play, where you play each disc in the order loaded
Normal play (TRACK mode), where the CD changer acts like a regular CD player, playing the next disc in the queue from start
to finish, then stopping.
See “Normal play (TRACK mode)”
(
÷ Repeat Play, which plays the tracks or discs over and over
Cahpter1
Repeat mode where the CD changer plays a particular disc or set of tracks over and over.
See “Repeated playback (REPEAT mode)”
™
÷ Random Play, which plays the tracks on the loaded CDs in random order
Random mode where the CD changer plays all tracks on all discs loaded in the carousel in random order, without repeating any
tracks.
See “Playback in a random order (RANDOM mode)”
£
÷ Programmed play order
See “Programming tracks in desired order (PGM mode)”
¢
Cahpter2
÷ Continuous Play, which lets your CD changer function as your own personal jukebox, providing continuous
music — a CD plays on one player while the next CD is queuing up on the other
Continuous mode where the CD changer uses both players to provide seamless continuous audio—while a disc plays on one
player, another is queued on the second player.
See “Continuous playback”
§
÷ Timed Play, where you use an optional audio timer to automatically begin playing all CDs or only specified
CDs
Cahpter3
See “Timer operation”
÷ Internal processing that recognizes and stores disc data such as DTS registration
See “Registration of DTS discs”
¶
•
Your CD changer includes a standard remote and a remote keyboard (for easier text entry).
You can use either device to control the changer. For the sake of simplicity, this manual provides stan-
dard remote instructions for all functions except text entry.
Cahpter4
The keyboard enables you to operate either player. To operate player A, press the keyboard buttons as
normal. To operate player B, hold down ROOM B button while pressing the appropriate keyboard but-
tons.
Cahpter5
Cahpter6
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Up to 200 CDs can be loaded in the carousel. Disc exchange
also is possible during playback.
17
Never let your hand or any object enter inside the unit.
Loading discs in the carousel
1Switch power ON.
Chapter1
Press the POWER (
) button.
Main unit
STANDBY
POWER
ON/STANDBY
Chapter2
2Open the disc door toward the front.
Press PUSH OPEN at the right top of
the disc door.
÷ Do not place any object on the open disc door.
Chapter3
3Load discs.
1Turn the DISC SKIP knob and bring the slot with
the disc to be placed to the front.
DISPLAY-A (or DISPLAY-B)
Chapter4
DISC001 E1:23•
The slot No. is displayed when the DISC SKIP knob is turned.
DISPLAY-B (or DISPLAY-A)
COCO OPENOUSECT
Carousel
Disc slot
2Insert the disc vertically.
Chapter5
Insert discs with the label on the right side. Playback is not
possible when a disc is inserted the other way round.
Insert CDs with the label side
facing toward your right.
NNoottee
÷Do not insert more than one disc in a slot.
÷ When a disc not corresponding to CD-TEXT is inserted, searching for
this disc will be facilitated when the title is registered at the time of disc
insertion.
Chapter6
“Registration of Title”
º
Insert one CD per slot all the way.
3Repeat 1 and 2 to insert discs.
4Close the disc door.
÷When a title has been registered and the disc door is closed, reading
operation is performed automatically.
Chapter7
DISPLAY-A : The display flashes.
DISCCDETECTIO 3
NN
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
18
Disc replacement
Discs can be replaced with the same procedure as “Loading discs
in the carousel”. In stopped condition, all discs can be exchanged.
However, when the disc door is opened while “DISC DETEC-
TION” is being displayed, it may not be possible to remove the
disc which had been played. Accordingly, wait for the “DISC
DETECTION” indication to go out before opening the disc door.
When the disc information has been read in at the time of regis-
tration of disc information like title, music type, etc., the disc
information can be recalled even when the disc insertion place
Cahpter1
is changed.
⁄
Selecting Player A or B
The audio played on Player A is output from OUTPUT-A and that
played on Player B is output from OUTPUT-B. This makes it pos-
sible to enjoy different music in different rooms.
Cahpter2
÷ Each press of the button switches Players A and B alternately and lights
the indicators accordingly.
Main unit
B
A
÷ After selecting the Player, operate the player.
÷ The OPERATION A-B button is set to A during continuous play mode.
It is not possible to switch the Player during it.
OPERATION
÷If a registered DTS disc is selected when the Player B is selected,
blinking “DTS DISC!“ is displayed and the DTS disc selection is
cancelled.
•
Cahpter3
In regard to ALL DATA READ mode (Player A only)
To display the title on a LCD remote control unit (provided
with a KENWOOD Receiver or optional), perform the all data
readoperationfirst, andoperatetheLCDremotecontrolunit
with the door left closed. For the operation of the LCD
remote control unit, refer to the instruction manual provided
with your receiver or LCD remote control unit.
The disc information for all discs will be read. It is convenient to
execute this mode before playback after discs have been exchanged.
Close the disc door before operation.
Each press switches the modes as follows:
1 Press the MODE button.
1 MUSIC TYPE
2 DISC SEARCH
Cahpter4
MODE
3 TITLE INPUT
4 ALL DATA READ
5 ALL INFORMATION
6 DTS DISC SKIP
2 Select “ALL DATA READ”.
DISPLAY-A
DISC SKIP
DOWN
UP
ALL DATA READ3
Search in progress or
Cahpter5
reading information
The display flashes.
DDISCCREADING3
3 Set the input.
When the disc is CD-TEXT
SET
D001:: CDATEXT3
÷ Repeat the above procedure so that the complete disc information is
read into the CD player.
Cahpter6
÷ In the case of a non-CD-TEXT disc, the “D001:NO CD TEXT” display
will appear for approx. 3 seconds.
÷ This operation is not available during the continuous play mode.
To quit ALL DATA READ mode
Press the 7 button.
1. Please remove all CDs from the carousel before moving the unit.
2. If blinking “PLEASE WAIT“ is displayed when the disc door is opened, do not attempt to change the disc.
NNootteess
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
(TRACK mode)
Normal play
19
The 10-key remote is not capable of controlling Player B. It should
be controlled from the keyboard. Be sure to hold the ROOM B
button when controlling Player B.
Preparation
÷Select the Player A or Player B.
*
Chapter1
Playing tracks in order from track No.1
Use the following procedure to play a CD in the original order of tracks from track No.1.
Chapter2
1Select the disc.
÷Each press of a button increases (or decreases) the disc number.
Holding the button depressed varies the disc numbers successively.
÷When the disc corresponds to CD-TEXT, or when the disc title has been
registered, the disc title will be displayed with scrolling. Discs can be
selected by the disc title.
DISC SKIP
DOWN UP
Chapter3
Next disc
Previous disc
“Registration of Title”
º
Display when disc No. 123 is selected
Go to step 2 within 8 sec.
D123
1:23
Chapter4
2Start playback.
÷When the disc corresponds to CD-TEXT, or when the track titles have
been registered, the track title is displayed.
ENTER
6
÷If the selected disc is being played on the other player, blinking
“DISCXXX BUSY!” is displayed and the disc will not be played.
For continuous playback
Press the CONTINUOUS PLAY button.
Chapter5
To pause playback
To stop playback
ENTER
7
6
Chapter6
÷Each press pauses and plays the CD alternately.
Press the SUB OUT MONITOR button to output the audio played
on Player B from OUTPUT-A. Each press of the button switches
this feature on and off alternately.
In regard to SUB OUT MONITOR
SUB OUT
MONITOR
Chapter7
C
DISPLAY-A
SUBOOUTNMONITOR
÷This operation is not available during the continuous play mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal play (TRACK mode)
Direct disc selection
20
1 Press the DISC SELECTOR button.
Press the numeric buttons in the following order...
Disc No. 63 : 6, 3
Disc No. 100 : 1, 0, 0
DISC
SELECTOR
X
÷If the selected disc is being played on Player B, blinking “DISCXXX
BUSY!” is displayed and the disc will not be played.
Within 8 seconds!
2 Input the disc number.
How to input numeric values
Cahpter1
1
2
3
J
4
K
H
I
The input method for this product is of two different types. One
can either use the traditional KENWOOD +10 button approach,
or direct numeric input.
5
L
6
7
8
M
N
O
SpecialinputmethodforCDplayerwith200-discchanger
To input 42 : 4, 2
To input 115 : 1, 1, 5
9
P
0
Q
+10
R
+100
S
To input 200 : 2, 0, 0
Cahpter2
Within 8 seconds!
Same input method as other KENWOOD products
To input 42 : +10, +10, +10, +10, 2
To input 115 : +100, +10, 5
3 Start playback.
ENTER
To input 200 : +100, +100
6
Cahpter3
What is the “normal play TRACK mode”?
To set the unit to the TRACK mode:
Playback is made from the first track. The normal playback mode
is called TRACK mode. Press the CONFIRM button to confirm the
present mode.
At the time of PGM mode:
Press the P.MODE button.
CHARAC.
/P.MODE
CONFIRM
A
Cahpter4
At the time of BEST SELECTION mode:
Press the 7button during playback.
TRACK mode
7
TRACK01D120:T02
At the time of MUSIC TYPE mode:
Press the MODE button.
MODE
PGM mode
Cahpter5
PGM0101D131:T02
BEST SELECTION mode
At the time of RANDOM mode:
Select “RANDOM OFF”.
BEST011D104:T03
MUSIC TYPE mode
RANDOM
F
M.TYPE1DRhythm2
RANDOM mode
Cahpter6
At the time of REPEAT mode:
Select “REPEAT OFF”.
ONE0DISC1RANDOM
REPEAT mode
REPEAT
E
PGREPEAT1ON:T02
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal play (TRACK mode)
21
The 10-key remote is not capable of controlling Player B. It should
be controlled from the keyboard. Be sure to hold the ROOM B
button when controlling Player B.
Preparation
÷Select the Player A or Player B.
*
Chapter1
Playback from desired track
1Select the disc.
Chapter2
1Select the disc number.
DISC SKIP
DOWN
UP
Display when disc No. 123 is selected
Previous disc
Next disc
D123
1:23
Within 8 seconds!
Chapter3
2Set the input.
÷The disc number can be selected directly by using the DISC SELECTOR
and numeric buttons in place of the DISC SKIP (DOWN/UP) buttons.
÷When the disc corresponds to CD-TEXT, or when the disc title has been
registered, the disc title will be displayed with scrolling. Discs can be
selected by the disc title.
SET
“Registration of Title”
÷Repeat step 1 when it is required to change the disc number.
º
Go to step 2 within 8 sec.
Chapter4
2Select the track number.
1Input the track number.
Press the numeric buttons in the following order...
Track No.8
: 8
Track No.14 : 1, 4
Track No.20 : 2, 0
1
H
2
I
3
J
4
K
Display when track No. 8 is selected
5
L
6
7
8
M
N
O
D123 08
1:23
9
P
0
Q
+10
R
+100
S
Chapter5
÷When the disc corresponds to CD-TEXT, or when the track titles have
been registered, the track title is displayed. Tracks can be selected by
the track title.
Within 8 seconds!
“Registration of Title”
º
2Set the input.
÷Playback starts.
SET
÷If the selected disc is being played on the other player, blinking
“DISCXXX BUSY!” is displayed and the disc will not be played.
÷Repeat step 2 when it is required to change the track number.
Chapter6
Skipping tracks
Searching
CURSOR
CHARACTER
UP
LEFT
RIGHT
DOWN
1
¡
4
¢
Backward search
Forward search
To skip backward
To skip forward
Chapter7
÷When the 4 button is pressed once during playback, the track being
played will be played from the beginning.
÷Playback starts from the position where the button is released.
Download from Www.Somanuals.com. All Manuals Search And Download.
(REPEAT mode)
Repeated playback
22
The 10-key remote is not capable of controlling Player B. It should
be controlled from the keyboard. Be sure to hold the ROOM B
button when controlling Player B.
Preparation
÷ Select the Player A or Player B.
*
Cahpter1
To repeat only the desired tracks (Player A only)
1Program the desired tracks by performing steps 1
to 3 of “Programming tracks in desired order”.
¢
÷Up to 32 tracks can be programmed by repeating steps 1.
Cahpter2
2Switch REPEAT ON.
PGREPEAT2ONDT03
REPEAT
E
÷The current status is displayed when the button is pressed once. When
it is pressed while the status is displayed, the repeat ON status can be
set to OFF (or vice versa).
3Start playback.
Cahpter3
÷All of the programmed tracks will be repeated.
÷If a track to be played is located in the disc played on Player B, that track
will be skipped.
ENTER
6
÷In case only one track is programmed, only that track will be repeated.
To cancel repeated playback
Press the REPEAT button twice. (REPEAT ON → OFF)
To repeat one selected disc
Cahpter4
1Check that the Player is in the normal play TRACK
mode.
)
2Select the disc number.
DISC SKIP
DOWN
UP
÷Thediscnumbercanbeselecteddirectlybyusingthe DISCSELECTOR
and numeric buttons in place of the DISC SKIP (DOWN/UP) buttons.
Previous disc
Within 8 seconds!
Next disc
Cahpter5
3Start playback.
÷If the selected disc is being played on the other Player, blinking
“DISCXXX BUSY!” is displayed and the disc will not be played.
ENTER
6
PGREPEAT2ONDT03
4Switch REPEAT ON.
÷The current status is displayed when the button is pressed once. When
it is pressed while the status is displayed, the repeat ON status can be
set to OFF (or vice versa).
REPEAT
E
Cahpter6
÷The operation is not available during the continuous play mode.
To cancel repeated playback
Press the REPEAT button twice. (REPEAT ON → OFF)
For random repetition
For music type or user file repetition
For best selection repetition
£
fi
°
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
(RANDOM mode)
Playback in a random order
Use the following procedure to activate random playback
which selects a track at random after every track. This fea-
ture may allow you to play CDs for long hours without
getting tired of.
23
The 10-key remote is not capable of controlling Player B. It should
be controlled from the keyboard. Be sure to hold the ROOM B
button when controlling Player B.
Preparation
÷ Select the Player A or Player B.
*
Chapter1
Chapter2
Check that the Player is in the normal play
TRACK mode.
1
)
2Select discs.
To select one disc
1Select the disc number.
÷Thediscnumbercanbeselecteddirectlybyusingthe DISCSELECTOR
and numeric buttons in place of the DISC SKIP (DOWN/UP) buttons.
DISC SKIP
DOWN UP
Chapter3
Next disc
Previous disc
÷If the selected disc is being played on the other Player, blinking
“DISCXXX BUSY!“ is displayed and the disc will not be played.
÷“ONE DISC RANDOM“ cannot be selected during the continuous play
mode.
Within 8 seconds!
2Start playback.
Each press switches the modes as follows:
ENTER
6
1 ONE DISC RANDOM
RANDOM
2 ALL DISC RANDOM
F
3 RANDOM OFF
Chapter4
3Select “ONE DISC RANDOM”.
<<<><E012 ><>>>
RANDOM
F
The number here changes.
÷Each time a track ends, the same operation as above is repeated,
and the track selected next is played.
÷Random play stops after all of the tunes have been played once.
÷If a track to be played is located in the disc played on the other Player,
that track will be skipped. (This track will not be selected later unless
the REPEAT mode is set.)
Chapter5
To select all discs
Select “ALL DISC RANDOM”.
For repeated playback
RANDOM
F
Press the REPEAT button to select “REPEAT ON”.
Chapter6
For continuous playback (ALL DISC RANDOM only)
Press the CONTINUOUS PLAY button.
To select another track in the middle of playing one
To cancel random playback
Select “RANDOM OFF”.
CHARACTER
DOWN
UP
RANDOM
4
¢
7
F
or
Chapter7
÷ Pressingthe4 buttononcereturnstothebeginningofthetrackbeing
played.
÷Press the 7 button to stop playback.
÷Normal playback will be performed when RANDOM OFF is selected.
For random music type or random user file
fi
Download from Www.Somanuals.com. All Manuals Search And Download.
(PGM mode)(Player A only)
Programming tracks in desired order
Use the following procedure to select desired tracks (up to
32 tracks) from different discs and program them in the
desired order.
24
Preparation
÷Set the Player A to stop mode.
Cahpter1
1Press so that the “PGM” indicator lights.
CHARAC.
DISPLAY-A
/P.MODE
Cahpter2
PGM3SELECT1DISC
2Select the disc.
1Select the disc number.
DISC SKIP
DOWN
UP
Cahpter3
Previous disc
Next disc
PGM01ED2001DISC
Within 8 seconds!
÷Thediscnumbercanbeselecteddirectlybyusingthe DISCSELECTOR
and numeric buttons in place of the DISC SKIP (DOWN/UP) buttons.
÷When the disc corresponds to CD-TEXT, or when the disc title has been
registered, the disc title will be displayed with scrolling. Discs can be
selected by the disc title.
2Set the input.
SET
“Registration of Title”
÷If you make a mistake, press the CLEAR button and enter the disc No.
from the beginning.
º
Cahpter4
Go to step 3 within 8 sec.
3Select the track number.
1Input the track number.
Press the numeric buttons in the following order...
1
H
2
I
3
J
4
K
Track No.8 : 8
Track No.14 : 1, 4
Track No.20 : 2, 0
5
L
6
7
8
Cahpter5
M
N
O
PGM01ED2001T--C
9
P
0
Q
+10
R
+100
S
÷ To program the entire disc, press the SET button without inputting the
track number. “ALL” will be displayed.
Within 8 seconds!
÷ When the disc corresponds to CD-TEXT, or when the track titles have
been registered, the track title is displayed. Tracks can be selected by
the track title.
2Set the input.
SET
“Registration of Title”
º
÷ Program other tracks in the desired order by repeating steps 2 and 3.
÷ Up to 32 tracks can be programmed. “FULL” is displayed when no
more tracks can be programmed.
Cahpter6
÷ If you make a mistake, press the CLEAR button and restart from step
2.
4Start playback.
÷Tracks will be played in the order they are programmed.
÷If a track to be played is located in the disc played on Player B, that track
will be skipped.
÷When the 4 or ¢ button is pressed during playback, the track will
be skipped in the direction of the pressed button.
ENTER
6
Cahpter7
For continuous playback
Press the CONTINUOUS PLAY button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming tracks in desired order (PGM mode) (Player A only)
25
Chapter1
To check the programmed tracks
Chapter2
DISPLAY-A
SPACE
/CHECK
PGM01EDD200DT03
÷ Each time the button is pressed, the program No. and the disc No. are
displayed.
÷ The previous display resumes in a few seconds.
Chapter3
To add a track to the program
1Set the Player A to stop mode.
÷ When a track No. is entered, the track will be added to the end of the
existing program.
2Perform steps 2 and 3 of “Programming tracks in
desired order”.
¢
Chapter4
To change a track in the program
1Set the Player A to stop mode.
2Press the CHECK button.
÷Press the CHECK button repeatedly until the program No, to be
changed is displayed.
SPACE
/CHECK
DISPLAY-A
Chapter5
PGM01EDD200DT03
Example
3Perform steps 2 and 3 of “Programming tracks in
≠
desired order”.
¢
÷Press it while the “PGM01” indicator blinks.
÷The track being played cannot be changed.
Chapter6
To clear tracks from the program
To clear tracks from the end
To clear all tracks
DELETE
/CLEAR
CHARAC.
/P.MODE
Chapter7
÷ Each time the button is pressed, the last track in the program is cleared.
÷ The tracks which are programmed earlier than the track being played
cannot be cleared.
÷ Whenthe P.MODEbuttonispressedduringplayback, playbackinorder
of tracks starts from the track being played.
Download from Www.Somanuals.com. All Manuals Search And Download.
Continuous playback
With this feature, the time required for disc change can be
minimized so even different discs can be played naturally
and almost continuously.The same audio signal is output
at both OUTPUT-A and OUTPUT-B.
26
Preparation
÷ Close the disc door.
÷ Set the Player B to stop mode.
&
Cahpter1
DISPLAY-B
Cahpter2
Initiate the continuous play mode.
CONTINUOUSUPLAY
CONTINUOUS
PLAY
÷ The OPERATION A-B button is set to A during continuous play mode.
÷ When the disc door is opened, the continuous play mode is released
and playback also stops.
B
÷ It is not possible to select a DTS disc during continuous play mode.
Cahpter3
To quit continuous play mode
Press the CONTINUOUS PLAY button.
For continuous playback in normal play mode
For continuous playback in PGM mode
(
¢
Cahpter4
For continuous playback in ALL DISC RANDOM mode
£
For continuous playback in MUSIC TYPE PLAY mode
fi
Cahpter5
For continuous playback in BEST SELECTION mode
°
Cahpter6
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
(Player A only)
Timer operation
Audio timer
As this unit incorporate the timer standby function, play-
back can be started at desired moment if a commercially
available audio timer is combined with this unit.
12:00
To AC outlet
27
Receiver or Amplifier
Preparation
÷Select the Player A.
*
÷Connect the system components so that
their power can be switched on by the timer.
÷Read the instruction manual of the timer
carefully.
Chapter1
Audio cable
This unit
Chapter2
Set the power switches of the system compo-
nents to the ON positions.
1
2Select the disc to be played.
1Select the disc number.
÷ ThediscnumbercanbeselecteddirectlybyusingtheDISCSELECTOR
and numeric keys in place of the DISC SKIP (DOWN/UP) buttons.
DISC SKIP
DOWN
UP
Chapter3
Previous disc
Next disc
Within 8 seconds!
2Play the disc.
Chapter4
ENTER
÷If the selected disc is being played on Player B, blinking "DISCXXX
BUSY!" is displayed. In this case, either stop Player B and select the
same disc again, or select another disc.
6
Chapter5
3Set the listening volume.
1Adjust the volume on the amplifier or receiver.
2Stop playback.
Chapter6
4Set the timer for the desired ON time.
5Set the TIMER PLAY switch to ON.
÷Read the instruction manual of the timer carefully.
Main unit
Chapter7
TIMER PLAY
÷When the set time comes, playback will start automatically.
÷The playback mode will be TRACK mode.
OFF
ON
Download from Www.Somanuals.com. All Manuals Search And Download.
Registration of DTS discs
When playing DTS-encoded discs, excessive noise will be exhibited from the analog stereo outputs. If DTS discs are regis-
tered beforehand, the audio signal from the Player B (analog OUTPUT-B) is skipped. Use the following procedure before
playing the DTS disc.
28
Preparation
÷ Load DTS discs into the carousel.
&
÷ Check that the Player A is in the normal play
TRACK mode.
)
Cahpter1
1Activate the dts disc skip mode.
1Press the MODE button.
÷ When the MODE button is pressed during DTS DISC SKIP mode, the
DTS DISC SKIP mode is cancelled.
MODE
Each press switches the modes as follows:
1 MUSIC TYPE
2Select “DTS DISC SKIP”.
Cahpter2
DISC SKIP
2 DISC SEARCH
DOWN
UP
SET
3 TITLE INPUT
4 ALL DATA READ
5 ALL INFORMATION
6 DTS DISC SKIP
\
2Select “SET DTS DISC“.
DISC SKIP
DOWN
Cahpter3
UP
Each press switches the modes as follows:
1 SET DTS DISC
SET
\
2 CANCEL DTS DISC
3Select the DTS disc.
÷ The disc number can be selected directly by using the numeric keys in
place of the DISC SKIP (DOWN/UP) buttons.
÷ To register another DTS disc, repeat the procedure from step 3.
Select the disc number.
Cahpter4
DISC SKIP
DOWN
UP
DISPLAY-A
SET
Previous disc
Next disc
\
D001IDTSUSET?AY
To quit DTS DISC SKIP mode
Press the MODE button.
To delete the DTS registration
Cahpter5
Use the following procedure before moving or changing a DTS disc, and register the disc again.
1Perform steps 1 of “Registration of DTS discs“.
2Select “CANCEL DTS DISC“.
Each press switches the modes as follows:
DISC SKIP
DOWN
SET
UP
1 SET DTS DISC
2 CANCEL DTS DISC
\
Cahpter6
DISPLAY-A
3Select the DTS disc to be deleted.
D001IDTSUCANC.?
DISC SKIP
DOWN
UP
SET
Previous disc
Next disc
\
To quit DTS DISC SKIP mode
Press the MODE button.
Cahpter7
When a DTS disc is played, the audio signal is not output at the analog OUTPUT A jacks.
NNoottee
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 : Specifying and Using Disc or Track Data
Thanks to sophisticated design and onboard memory storage, your CD changer can read and store additional
information about the discs you load, enabling you to choose discs by title information rather than just disc
position.
29
This memory feature means you don’t have to remember what disc is stored in which slot or spend time creating
a list of what you’ve loaded.
Chapter1
Here’s how it works: every CD has an unique ID code embedded in it.The changer reads this code and associates
with it any other information that it reads or that you enter for the disc. It stores the information internally so
that when you load or play the disc, the changer still contains the disc and track titles (among other things).
1. Your CD changer will recall information read in at the time of registration even when the disc insertion place is changed.
2. Your changer stores this information for up to 210 discs, which allows you to rotate discs between the changer and
NNootteess
another CD player (for example, in your car) without losing any information read.
Chapter2
The CD changer can :
÷ read data from discs containing encoded CD Text information
÷ store disc and title information you enter using the 10-key remote, keyboard and LCD remote*.
÷ allow you to use the read or entered data to select discs
Chapter3
÷ allow you to program disc play for custom listening order
* VR-4900, KRF-V9993D and VR-4700 (Model available may differ depending on the country and sales area.)
The remote control unit of these receiver models can also be used to input titles or display information such as the titles.
The changer reads any data you specify when you play the disc or when you instruct the changer to read all
data.
Your CD changer includes a standard remote and a remote keyboard.You can use either device to control
the changer. For the sake of simplicity, this manual provides standard remote instructions for all functions
except text entry
Chapter4
The keyboard enables you to operate either player. To operate player A, press the keyboard buttons as
normal.To operate player B, hold down ROOM B button while pressing the appropriate keyboard buttons.
You can use this internal processing to control various features, such as :
÷ Playing discs of a predefined or user-specified MusicType that you can assign to each CD
Chapter5
See “Listening to music by genre (MUSIC TYPE mode)”
‹
÷ Playing discs by selecting disc titles, either read from CDText encoding on the CD or entered using the remote
or keyboard
See “Disc search (DISC SEARCH mode)”
fl
÷ Assigning Best Selection status to your favorite tracks, then playing them at any time.
See “Listening to your favorite titles (BEST SELECTION mode)”
°
Chapter6
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Registration of Title
For discs not corresponding to CD-TEXT, a title can be given
to the disc (max. 25 characters). Up to 20 tracks titles can
be registered per disc. Operation is possible also when the
disc door is open. We recommend to register titles while
discs are being inserted.
30
Preparation
Although all operations can be controlled from both the
10-keyRemoteandKeyboardremotecontrolunits, donot
change the remote control unit in the middle of operation
suchascharacterinput. Otherwise, charactersmaynotbe
input correctly.
÷Set the Player A to stop mode.
÷Check that the Player A is in the normal play
TRACK mode.
)
Cahpter1
(TITLE INPUT mode)
Assigning Title
1Switch to title input mode.
10-Key Remote
÷ When the MODE button is pressed during TITLE INPUT mode, the title
input mode is cancelled.
10-key Remote
Keyboard
1Select “TITLE INPUT”.
Cahpter2
Keyboard
DISC SKIP
Press the TITLE INPUT
button.
DOWN
UP
MODE
÷ When the TITLE INPUT button is pressed during TITLE INPUT mode,
the title input mode is cancelled.
\
TITLE
INPUT
DISPLAY-A : The display flashes.
TITLEIINPUTNDOM
2Set the input.
SET
D---CT-- SELECT
÷To enter track titles without assigning the disc title, go to “To enter the
Cahpter3
track title“.
⁄
2Enter the title.
To enter the disc title
10-key Remote
Keyboard
÷ The disc number can be selected directly by using the numeric buttons
in place of the DISC SKIP(DOWN/UP) buttons.
÷ During playback, the disc only being played can be selected.
1Select the disc number.
4
DISC
SKIP
DISC
SKIP
UP
DISC SKIP
DOWN
DOWN
UP
Next disc
Next disc
Previous disc
Previous disc
2Set the input.
10-key Remote Main unit
÷ If a desired character is not provided on the remote control buttons,
input the character as follows. Press the CHARACTER (DOWN/UP)
buttons or rotating the DISC SKIP knob on the main unit (provided that
the OPERATION-A indicator is lit) until the desired character is dis-
played in the flashing cursor position. Then, press the SET button.
SET
SET
Cahpter5
3Enter the disc title.
CONTINUOUS SUB OUT
CONFIRM
A
PLAY
MONITOR
=
B
C
ZABC
>
BEST
(
9
)
0
!
1
@
2
#
3
$
4
%
5
^
6
&
7
✱
8
-
+
=
SELECTION REPEAT
RANDOM
F
DISPLAY
G
D
E
Q
W
E
R
T
Y
U
I
O
P
,
1
H
2
3
J
4
K
Flashing cursor
I
,,
,
:
;
A
S
D
F
G
H
J
K
L
5
L
6
M
7
N
8
O
÷One character is set and the cursor goes to the next digit.
÷Repeat this to enter the disc title.
<
,
>
.
?
/
Z
X
C
V
B
N
M
9
P
0
Q
+10
R
+100
S
Cahpter6
.
/
–
1. For discs corresponding to CD-TEXT, a new title can not be
'
T
U
V
W
registered.
NNootteess
DISC
SELECTOR
(
)
X
Y
Z
2. As the entered title and the CD-TEXT title information are
memorized, the information may be displayed even when a
disc has been removed.
4Store the disc title.
TITLEISTORE!!OM
÷To register the disc title of another disc, repeat the entire procedure of
ENTER
ENTER
6
Cahpter7
“To enter the disc title“.
Download from Www.Somanuals.com. All Manuals Search And Download.
Registration of Title
In regard to disc information reading
31
The entered title is read in to the disc with the following
timing.
÷ When the disc door is closed.
÷ With closed disc door, when title input mode is finished.
DISPLAY-A : The display flashes.
Chapter1
DDISCCREADING3
When there are discs for which the disc information already has been
read in, there may be no display.
Do not move or exchange discs until the disc information
has been read in.
Chapter2
To enter the track title
10-key Remote
Keyboard
1Select the track number.
DISPLAY-A
CHARACTER
UP
DOWN
4
¢
4
¢
D001CT07
N e x t
track
Previous
track
Previous
track
Next track
Chapter3
2Press the SET button.
SET
SET
10-key Remote
Main unit
3Enter the track title.
÷ If a desired character is not provided on the remote control buttons,
input the character as follows. Press the CHARACTER (DOWN/UP)
buttons or rotating the DISC SKIP knob on the main unit (provided that
the OPERATION-A indicator is lit) until the desired character is dis-
played in the flashing cursor position. Then, press the SET button.
CONTINUOUS SUB OUT
CONFIRM
A
PLAY
MONITOR
B
C
BEST
SELECTION REPEAT
RANDOM
F
DISPLAY
G
(
9
)
0
!
1
@
2
#
3
$
4
%
5
^
6
&
7
✱
-
+
=
D
E
Chapter4
8
1
H
2
3
J
4
K
Q
W
E
R
T
Y
U
I
O
P
,
I
,,
,
:
;
A
S
D
F
G
H
J
K
L
5
L
6
M
7
N
8
O
<
,
>
.
?
/
Z
X
C
V
B
N
M
9
P
0
Q
+10
R
+100
S
=
ZABC
>
.
/
–
'
T
U
V
W
DISC
SELECTOR
(
)
Flashing cursor
X
Y
Z
÷ One character is set and the cursor goes to the next digit.
÷ Repeat this to enter the track title.
Chapter5
4Store the track title.
TITLEISTORE!!OM
÷ To register another track titles in the same disc, repeat the entire
ENTER
ENTER
6
procedure of “To enter the track title“.
÷Up to 20 track titles can be registered per disc by repeating steps from
1 to 4 for each.
To quit TITLE INPUT mode
Press the MODE button.
Chapter6
To change the character type
10-key Remote
10-key Remote
Keyboard
÷ The type of characters which can be entered is switched each time the
CHARAC. button is pressed.
SHIFT
CHARAC.
/P.MODE
=
1
Capital letters : ABC.....XYZ.....
Small letters : abc.....xyz.....
zabc
>
ZABC
=
>
2
3
Chapter7
Numbers/symbols : 0 1 2 3.....7 8 9
Holding this button down,
press a character or
numeric button.
=
>
012
space ! " # $ % & ' () + , - . / : ; < = >
*
? @ ^ _ ` 0.....
Keyboard
÷ To input a small (lowercase) letter or a symbol, press and hold SHIFT
while press the desired character or numeric/symbol button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Registration of Title
32
Preparation
÷Close the disc door.
&
Cahpter1
To change or delete a title
÷ Call the disc or track to be changed.
1 2
of “Assigning Title”.
1Perform steps 1 and 2- ,
2Change or delete characters one by one.
÷ Deletion mode is cancelled when the MODE button is pressed.
º
Cahpter2
DISPLAY-A
Change
10-key Remote
Keyboard
=
ZABC
SONEBODYCT
+ Move with the CURSOR button =
>
1Move the cursor to the desired character (to be
changed).
CURSOR
L
CURSOR
R
CURSOR
LEFT
RIGHT
÷ If the title to be changed is too long to be displayed on the display
section, press the CURSOR button to scroll the display so that the
characters hidden until then appear.
1
¡
÷ No character can be changed if 25 characters have already been input.
In this case, delete unnecessary characters then enter the desired
correction characters.
Cahpter3
2Select a character.
CONTINUOUS SUB OUT
CONFIRM
PLAY
MONITOR
A
B
C
BEST
DISPLAY-A
SELECTION REPEAT
RANDOM
F
DISPLAY
G
(
9
)
0
!
1
@
2
#
3
$
4
%
5
^
6
&
7
✱
8
-
+
=
D
E
Q
W
E
R
F
T
Y
H
U
I
O
P
1
H
2
3
J
4
K
,
I
=
,,
,
:
;
SONEBODYCT
LMNO
>
A
S
D
G
J
K
L
5
L
6
M
7
N
8
O
<
,
>
.
?
/
Z
X
C
V
B
N
M
9
P
0
Q
+10
R
+100
S
Flashing cursor
.
/
–
'
10-key Remote
Main unit
T
U
V
W
DISC
SELECTOR
(
)
Cahpter4
X
Y
Z
÷ If a desired character is not provided on the remote control buttons,
input the character as follows. Press the CHARACTER (DOWN/UP)
button or rotating the DISC SKIP knob on the main unit (provided that
the OPERATION-A indicator is lit) until the desired character is dis-
played in the flashing cursor position. Then, press the SET button.
3Delete the unnecessary character.
(See “Deletion”.)
Deletion
10-key Remote
Keyboard
Cahpter5
1Move the cursor to the desired character (to be
To enter a space
10-key Remote
deleted).
CURSOR
L
CURSOR
R
Keyboard
CURSOR
LEFT
RIGHT
SPACE
/CHECK
SPACE
1
¡
2Press the DELETE button.
DELETE
DELETE
/CLEAR
÷ When a title is to be deleted, delete all characters one by one.
Cahpter6
3Execute title change or deletion.
10-key Remote
Keyboard
To quit TITLE INPUT mode
ENTER
ENTER
Press the MODE button.
6
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
(MUSIC TYPE mode)
Listening to music by genre
Discs can be registered separately by 26 types of music
genres.
33
Preparation
÷Close the disc door.
&
÷Check that the Player A is in the normal play
TRACK mode.
)
Chapter1
(MUSIC TYPE SET mode)
Registration of music type
1Activate the music type set mode.
Chapter2
÷ When the MODE button is pressed during MUSIC TYPE SET mode, the
MUSIC TYPE SET mode is cancelled.
1Press the MODE button.
MODE
Each press switches the modes as follows:
1 MUSIC TYPE
2Select “MUSIC TYPE”.
2 DISC SEARCH
DISC SKIP
3 TITLE INPUT
SET
DOWN
UP
Chapter3
4 ALL DATA READ
5 ALL INFORMATION
6 DTS DISC SKIP
DISPLAY-A : The display flashes.
3Select “MUSIC TYPE SET”.
MUSICITYPETNDOM
DISC SKIP
SET
DOWN
UP
DISPLAY-A : The display flashes.
Chapter4
MUSICITYPETSETM
2Select the music type.
Each press switches the modes as follows:
AdultContemporary→ AlternativeRock→ Children’sMusic→
Classical → Contemporary Christian → Country → Dance →
Easy Listening → Folk → Gospel → Hip Hop → Jazz → Latin →
Musical → New Age → Opera → Operetta → Pop Music → RAP
→ Reggae → Rock Music → Rhythm & Blues → Sound Effects
→ Sound Track → Spoken Word → World Music→Adult Con-
temporary → .....
Chapter5
DISC SKIP
SET
DOWN
UP
Previous type
Next type
DISPLAY-A : When “Rock Music” is selected
RockCMusicTNDOM
÷When the selected disc corresponds to CD-TEXT and contains a genre
code, that genre code is registered as the music type.
To confirm the genre code ...
Chapter6
“Complete CD-Text Info”
@
3Select the desired disc.
÷The disc number can be selected directly by using the numeric buttons
in place of the DISC SKIP(DOWN/UP) buttons.
÷Repeat step 3 if it is required to register another disc in the music type
selected above.
÷To register another music type, exit the MUSIC TYPE SET mode once
and restart from the beginning.
DISC SKIP
DOWN
UP
SET
Chapter7
Next disc
Previous disc
To quit MUSIC TYPE SET mode
Press the MODE button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to music by genre (MUSIC TYPE mode)
(USER FILE SET mode)
Registration of user's disc file
34
Eight user files are available for registering desired discs. This makes the user possible to create files registering the discs of
a favorite artist(s) or the user's favorite discs.
1Activate the user file set mode.
1Press the MODE button.
÷ When the MODE button is pressed during USER FILE SET mode, the
USER FILE SET mode is cancelled.
MODE
Cahpter1
Each press switches the modes as follows:
2Select “MUSIC TYPE”.
1 MUSIC TYPE
DISC SKIP
DOWN
2 DISC SEARCH
3 TITLE INPUT
SET
UP
4 ALL DATA READ
5 ALL INFORMATION
6 DTS DISC SKIP
Cahpter2
DISPLAY-A : The display flashes.
3Select “USER FILE SET”.
DISC SKIP
MUSICITYPETNDOM
DISPLAY-A : The display flashes.
SET
DOWN
UP
USERAFILEESETHM
2Select the desired user file.
Cahpter3
Each press switches the modes as follows:
USER FILE 1 → USER FILE 2→ USER FILE 3 → USER FILE 4 →
USER FILE 5 → USER FILE 6 → USER FILE 7 → USER FILE 8
→USER FILE 1 →.....
DISC SKIP
SET
DOWN
UP
Next file
Previous file
Cahpter4
3Select the desired disc.
÷The disc number can be selected directly by using the numeric buttons
in place of the DISC SKIP (DOWN/UP) buttons.
÷Repeat step 3 if it is required to register another disc in the user file
selected above.
÷To register another user file, exit the USER FILE SET mode once and
restart from the beginning.
÷The same disc can be registered in more than one user files.
÷If the CHECK button is pressed while the disc number is blinking, the
musictypeofthediscisdisplayedprovidedthatitsmusictypehasbeen
registered.
DISC SKIP
SET
DOWN
UP
Previous disc
Next disc
Cahpter5
To quit USER FILE SET mode
Press the MODE button.
To clear the music type or user file registered for a disc
Cahpter6
1Play the music type or user file.
fi
DISPLAY-A :
2PresstheCLEARbuttonduringplaybackofthedisc
to be deleted.
D122 TYPE CLEAR
DELETE
/CLEAR
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to music by genre (MUSIC TYPE mode)
When music types or user files have been registered for
the discs, it is possible to enjoy playback of discs of the
selected music type or user file. Random playback for a
selected music type or user file is also possible.
35
÷Close the disc door.
&
Preparation
÷Register music type or user file.
‹›
Chapter1
÷Check that the Player A is in the normal play
TRACK mode.
)
(MUSIC TYPE PLAY mode) (Player A only)
Playing the music type or user file
1Activate the music type play mode.
Chapter2
1Press the MODE button.
÷ When the MODE button is pressed during MUSIC TYPE PLAY mode,
the MUSIC TYPE PLAY mode is cancelled.
MODE
Each press switches the modes as follows:
1 MUSIC TYPE
2Select “MUSIC TYPE”.
2 DISC SEARCH
3 TITLE INPUT
DISC SKIP
DOWN
UP
SET
Chapter3
4 ALL DATA READ
5 ALL INFORMATION
6 DTS DISC SKIP
DISPLAY-A : The display flashes.
3Select “MUSIC TYPE PLAY”.
MUSICITYPETNDOM
DISC SKIP
DOWN
UP
SET
DISPLAY-A : The display flashes.
Chapter4
MUSICETYPERPLAY
2Select the music type or user file.
DISC SKIP
DOWN
UP
DISPLAY-A : When “USER FILE 1” is selected
Chapter5
USERCFILEE1PLAY
3Start playback.
÷Playback is performed in increasing order of the disc numbers they
were registered for the respective music type or user file. Skipping to
the next disc is done when the ¢ button is pressed.
÷If the disc to be played is being played in Player B, the disc will be
skipped.
÷Each time the CHECK button is pressed, the registered disc numbers
are displayed in increasing order of the disc numbers.
ENTER
6
Chapter6
For repeated playback
Press the REPEAT button to select “REPEAT ON”.
For random playback
Press the RANDOM button.
÷Select “RANDOM OFF” or press 7 button to quit random playback.
For continuous playback
Press the CONTINUOUS PLAY button.
Chapter7
To quit MUSIC TYPE PLAY mode
Press the MODE button.
DISPLAY-A
M.TYPETMODESOFF
Download from Www.Somanuals.com. All Manuals Search And Download.
(DISC SEARCH mode) (Player A only)
Disc search
Althoughalloperationscanbecontrolledfromboththe10-
key Remote and Keyboard remote control units, do not
change the remote control unit in the middle of operation
such as character input. Otherwise, characters may not be
input correctly.
Preparation
÷ Close the disc door.
&
º
36
÷ Input the title.
÷ Check that the Player A is in the normal play
TRACK mode.
)
(CHARAC. SEARCH mode)
By inputting the initial letter of the desired disc title, discs which have the disc titles beginning with that character can be
searched in sequence.
Searching a disc by the disc title
Cahpter1
1Activate the character search mode.
10-key Remote
Keyboard
1Press the MODE button.
÷ When the MODE button is pressed during CHARAC. SEARCH mode,
the CHARAC. SEARCH mode is cancelled.
MODE
MODE
Each press switches the modes as follows:
1 MUSIC TYPE
2Select “DISC SEARCH”.
2 DISC SEARCH
3 TITLE INPUT
Cahpter2
DISC SKIP
DISC
SKIP
DISC
SKIP
UP
DOWN
UP
DOWN
SET
4 ALL DATA READ
SET
5 ALL INFORMATION
6 DTS DISC SKIP
DISPLAY-A : The display flashes.
3Select “CHARAC. SEARCH”.
DISC SKIP
DISCCSEARCHNDOM
DISPLAY-A : The display flashes.
DISC
DISC
SKIP
UP
SKIP
DOWN
UP
DOWN
SET
SET
Cahpter3
CHARAC.ASEARCHM
Input the initial letter of the disc title to be
searched.
DISPLAY-A : When initial letter “A” is selected.
2
<AAR>ESEARCHC?M
÷ The initial letters of disc titles are searched insensitively to the upper-
10-key Remote
Keyboard
case and lowercase.
1Input the initial letter of the disc title
÷ Lowercase characters cannot be input in the CHARAC. SEARCH mode.
Cahpter4
to be searched.
Keyboard
CONTINUOUS SUB OUT
CONFIRM
A
PLAY
MONITOR
B
C
÷ To input a symbol, press and hold SHIFT while press the desired
BEST
(
9
)
0
!
1
@
2
#
3
$
4
%
5
^
6
&
7
✱
-
+
=
SELECTION REPEAT
RANDOM
F
DISPLAY
G
8
D
E
numeric/symbol button.
Q
W
E
R
T
Y
U
I
O
P
,
1
H
2
3
J
4
K
I
10-key Remote
Main unit
,,
,
:
;
A
S
D
F
G
H
J
K
L
5
L
6
M
7
N
8
O
÷ If a desired character is not provided on the remote control buttons,
input the character as follows. Press the CHARACTER (DOWN/UP)
buttons or rotating the DISC SKIP knob on the main unit (provided that
the OPERATION-A indicator is lit) until the desired character is dis-
played in the flashing cursor position. Then, press the SET button.
÷ The type of characters (capital letters or numbers/symbols) is switched
each time the CHARAC. button is pressed.
<
,
>
.
?
/
Z
X
C
V
B
N
M
9
P
0
Q
+10
R
+100
S
.
/
–
'
T
U
V
W
DISC
SELECTOR
(
)
Cahpter5
X
Y
Z
2Set the input.
÷The disc titles beginning the specified character will be scrolled in the
display.
SET
SET
÷If there is no disc title beginning with the specified character, “NO
ENTRY” will be displayed.
To quit CHARAC. SEARCH mode
Press the MODE button.
Cahpter6
To search the next disc
To play the searched disc
10-key Remote
Keyboard
10-key Remote
Keyboard
DISC
SKIP
DISC
SKIP
UP
DISC SKIP
SET
DOWN
SET
DOWN
UP
Cahpter7
If the selected disc is being played on Player-B, blinking “DISCXXX BUSY!” is displayed and the disc will not be played.
NNoottee
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc search (DISC SEARCH mode) (Player-A only)
37
Preparation
÷ Close the disc door.
÷ Register music type or user file.
&
‹›
÷ Check that the Player A is in the normal play
TRACK mode.
)
Chapter1
(M.TYPE SEARCH mode)
The discs registered in the specified music type or specified user file can be searched in sequence.
Searching the music type or user file
Chapter2
1Activate the M.TYPE SEARCH mode.
1Press the MODE button.
÷ When the MODE button is pressed during M.TYPE SEARCH mode, the
M.TYPE SEARCH mode is cancelled.
MODE
Each press switches the modes as follows:
1 MUSIC TYPE
2Select “DISC SEARCH”.
2 DISC SEARCH
3 TITLE INPUT
DISC SKIP
Chapter3
DOWN
UP
SET
4 ALL DATA READ
5 ALL INFORMATION
6 DTS DISC SKIP
DISPLAY-A : The display flashes.
3Select “M.TYPE SEARCH”.
DISC SKIP
DOWN
UP
DISCCSEARCHNDOM
DISPLAY-A : The display flashes.
SET
Chapter4
M.TYPE.SEARCH M
Select the music type or user file to be
searched.
2
Each press switches the modes as follows:
USER FILE 1 → USER FILE 2→ USER FILE 3 → USER FILE 4 →
USER FILE 5 → USER FILE 6 → USER FILE 7 → USER FILE 8 →
AdultContemporary→ AlternativeRock→ Children’sMusic→
Classical → Contemporary Christian → Country → Dance →
Easy Listening → Folk → Gospel → Hip Hop → Jazz → Latin →
Musical → New Age → Opera → Operetta → Pop Music → RAP
→ Reggae → Rock Music → Rhythm & Blues → Sound Effects
→ Sound Track → Spoken Word → World Music →
USER FILE 1 → .....
DISC SKIP
DOWN
UP
Chapter5
SET
÷Ifthereisnodiscregisteredinthespecifiedmusictypeoruserfile, “NO
ENTRY” will be displayed.
To quit M.TYPE SEARCH mode
Press the MODE button.
Chapter6
To search the next disc
To play the searched disc
DISC SKIP
DOWN
UP
SET
Chapter7
If the selected disc is being played on Player-B, blinking “DISCXXX BUSY!” is displayed and the disc will not be played.
NNoottee
Download from Www.Somanuals.com. All Manuals Search And Download.
(BEST SELECTION mode) (Player A only)
Listening to your favorite titles
You can select only your favorite titles and register them
as the best selection. Use the following procedure to reg-
ister favorite tracks in the best selection file while playing
a CD.
38
Registration of best selection file
1Play the track to be registered.
Cahpter1
ENTER
÷ Only the track being played can be registered.
6
2Register it in the best selection file.
BEST
Cahpter2
DISPLAY-A
SELECTION
D
BEST01YD104LT03
Register other favorite tracks by performing
steps 1 and 2 for each of them.
3
÷ Up to 32 tracks can be registered. “FULL” is displayed when no more
disc is acceptable.
Cahpter3
Playing the best selection file
÷Set the CD player to stop mode
Preparation
÷Check that the unit is in the normal play track
mode
)
Cahpter4
DISPLAY-A
Press the BEST SELECTION button.
BEST0SELECTION3
÷ The tracks are played in the order they are registered.
÷ If a track to be played is located in the disc played on Player-B, that track
will be skipped.
BEST
SELECTION
D
÷ Each time the CHECK button is pressed, the disc numbers and track
numbers are displayed in the order they are registered.
Cahpter5
For repeated playback
Press the REPEAT button to select “REPEAT ON”.
For continuous playback
Press the CONTINUOUS PLAY button.
To quit BEST SELECTION mode
Press the 7 button during playback.
÷ The recorded contents remain stored even when best selection mode
is quit.
Cahpter6
To delete the registered best selection file
÷ This is done during best selection mode.
1Play the track to be cleared.
2Press the CLEAR button.
DISPLAY-A
DELETE
/CLEAR
BEST02LCLEARN03
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Chapter1
Chapter2
Chapter3
Chapter4
Chapter5
Chapter6
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 : Dual-Zone Capabilities
The CD-4900M/DPF-J9030 offers dual-zone output and control, which enables you to use the changer (along
with a Kenwood Dual-Zone/Dual-Source compatible receiver) to play 2 discs simultaneously in 2 rooms (or zones).
The changer can do this because it includes 2 complete CD players that can each access the full carousel of
loaded discs. Each player has its own analog output jacks and cables, and the primary player (output “A”) also
has a digital output connection.
40
Not all playback features can be used by both players or zones. The following chart shows which playback
features are available for each player and/or zone.
÷ Multi-room playback when used with a Kenwood receiver that has Dual-Zone/Dual-Source capability.
Cahpter1
Zone A/
Player A
Zone B/
Player B
Feature
DTS playback
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
Normal Play/Track mode
Random mode
‡
‡
‡
Cahpter2
Repeat mode
Program mode
Continuous Play mode
Music Type mode
Best Selection mode
Timed Play
Cahpter3
Remote control
Infrared remote keyboard
‡*
*TooperatetheremotekeyboardinZoneB, holddownROOMBbuttonwhilepressing
the appropriate keyboard buttons for the task.
Cahpter4
Cahpter5
Cahpter6
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 : In case of difficulty
In case of difficulty
41
Operation to reset
To reset the registered contents
The microcomputer may malfunction (impossibility to operate,
erroneous display, etc.) when the connection cords are un-
plugged while power is ON or due to an external factor. In this
case, execute the following method to reset the microcomputer
and return it to normal condition.
The registered contents for title, music type, user file, best se-
lection and DTS disc can be reset by the following procedure.
Chapter1
Unplug the power cord from the power socket, and while
holding the 7 button depressed, plug the power cord into
the socket again.
Unplug the power cord from the power socket and plug the
power cord into the socket again.
Chapter2
Remote control unit
Symptom
Cause
Remedy
Remote control operation is not possible.
÷ Batteries are exhausted.
÷ Replace with new batteries.
9
÷ The remote control unit is too far away from ÷ Operate the remote control unit within the
themainsystem, controllingangleistoolarge,
or there is an obstacle in between.
controllable range.
9
CD Player
Chapter3
Symptom
Cause
Remedy
No power is applied with the POWER(
key ON.
)
÷ Power plug is loosely connected.
÷ With the power plug connected to the
switchedACoutletofanamplifier, thepower
of the amplifier is turned off.
÷Insert the power plug firmly to the AC outlet.
÷Insert the power plug to the wall AC outlet.
Sound is not heard with the 6 key on.
÷ Disc is loose.
÷Insert disc properly.
÷Leave the player for about 1 hour so that the
condensation is removed.
&
÷ Condensation occured on the optical lens
unit.
w
Chapter4
÷ Disc is too dirty.
÷Wipe off the dust on the disc surface referring
to “Disc handling precautions”.
÷Replace the disc with a new one.
÷Connect all connection cords firmly. 6
w
÷ Disc is cracked.
÷ The connection cords are inserted loosely.
Music is interrupted. (Sound is skipped.)
÷ Disc is too dirty.
÷Wipe off the dust on the disc surface referring
to “Disc handing precautions”.
w
÷ Disc is cracked.
÷ Oscillation is applied to this unit.
÷Replace the disc with a new one.
÷Try selecting a place where no strong vibra-
tions occur by changing the installation place,
etc.
Chapter5
Disc selection is not possible.
÷RANDOM or BEST SELECTION mode is se- ÷Press the 7 key to quit RANDOM,BEST SE-
lected.
LECTION mode.
÷Press the MODE button to quit MUSIC TYPE
PLAY mode.
£°
÷MUSIC TYPE PLAY mode is selected.
fi
Disc begins to play when power is switched
ON.
÷ The TIMER PLAY switch is set to ON.
÷Set the TIMER PLAY switch to OFF unless
timer playback is required.
¶
Chapter6
When “REMOVE DISC XXX” is displayed:
A CD is inserted in the slot with the same disc number as the CD being loaded.
It is not permitted to insert another disc in a slot from which the CD has been loaded. Remove the inserted disc and insert it in an idle slot.
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Important items
42
Discs which can be played with this unit
Disc handling precautions
CD (12 cm), and the audio part of CDV, CD-G, CD-EG and CD-EXTRA.
Use discs that comply with the IEC standard, for example a disc carrying
COMPACT
Handling
Hold the discs so that you do not touch the
the
marking on the label surface.
DIGITAL AUDIO
playing surface.
÷An 8 cm CD cannot be played back.
Label side
Playing side
Cahpter1
Never play a cracked or warped disc
During playback, the disc rotates at high speed in the player.
Therefore, to avoid danger, never use a cracked or deformed disc or a
disc repaired with tape or adhesive agent.
Sticker
Do not attach paper or tape to either the play-
ing side or the label side of the discs.
Please do not use discs which are not round because they may cause a
malfunction.
Sticky paste
Cahpter2
Cleaning
Disc accessories
If fingerprints or foreign matter become at-
tached to the disc, lightly wipe the disc with
a soft cotton cloth (or similar) from the cen-
ter of the disc outwards in a radial manner.
The disc accessories (stabilizer, protection sheet, protection ring, etc.)
which are marketed for improving the sound quality or protecting discs
as well as the disc cleaner should not be used with this system because
they may cause malfunction.
Storage
When a disc is not to be played for a long
period of time, remove it from the player and
store it in its case.
Cahpter3
Maintenance of the unit
In regard to contact cleaner
When the front panel or case becomes dirty, wipe with a soft, dry
cloth. Do not use thinner, benzine, alcohol, etc. for these agents may
cause discoloration.
Do not use contact cleaners because it could cause a malfunction.
Be specially careful not to use contact cleaners containing oil, for
they may deform the plastic component.
Cahpter4
Caution on condensation
Note related to transportation and movement
Condensation (of dew) may occur inside the unit when there is a great
difference in temperature between this unit and the outside.
This unit may not function properly if condensation occurs. In this case,
leave the unit for a few hours with the power left ON, and restart the
operation after the condensation has dride up.
Before transporting or moving this unit, carry out the following op-
eration:
1. Remove all discs from the carousel and close the disc door.
2. Confirm that the flashing“NO DISC” display has changed to steady
lighting, and then switch off the power.
Cahpter5
Be specially cautious against condensatin in a following circumsatance:
When this unit is carried from a place to another across a large
difference in temperature, when the humidity in the room where
this unit is installed increases, etc.
DISPLAY-A and DISPLAY-B
NO DISC
3. Wait a few seconds, then disconnect the power plug.
Memory backup function
Stored contents for at least Power status (ON or OFF),
3 weeks after power plug is Title registration contents
unplugged from theAC out- Music type registration contents
Cahpter6
let.
User file registration contents
Best selection registration contents
DTS registration contents
Cahpter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 : Warnings and Specifications
43
Warnings
For the U.S.A.
FCC WARNING
Chapter1
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
NOTE :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interfer-
ence to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– – Reorient or relocate the receiving antenna.
Chapter2
– – Increase the separation between the equipment and receiver.
– – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– – Consult the dealer or an experienced radio / TV technician for help.
For the U.S.A.
CAUTION :
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,HACHIOJI-SHI,
TOKYO, JAPAN
Use of controls or adjustments or performance of procedures other than
Chapter3
those specified herein may result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions
of labels on, or inside the product relating to laser product safety.
KENWOOD CORP. CERTIFIES THIS EQUIPMENT CON-
FORMS TO DHHS REGULATIONS NO. 21 CFR 1040.10,
CHAPTER 1, SUBCHAPTER J.
Location: Back Panel
Chapter4
Specifications
[Format]
[Laser]
System ......................................... Compact disc digital audio system
Laser .................................................................... Semiconductor laser
Wave length..................................................................... 760 ~ 800 nm
Laser power class ............................................................. Class 1 (IEC)
[D/A Convertors]
[General]
D/A Conversion .............................................................................. 1 Bit
Power consumption ..................................................................... 14 W
Chapter5
Oversampling ............................................................... 8 fs (352.8 kHz)
Dimensions
W : 481 mm (18-15/16")
H : 163 mm (6-7/16")
D : 484 mm (19-1/16")
[Audio]
Frequency response ........................................ 4 Hz ~ 20 kHz, 0.5 dB
Signal to noise ratio...................................................More than 97 dB
Dynamic range ...........................................................More than 94 dB
Total harmonic distortion + noise
Weight (Net) ................................................................... 11 kg (24.3 lb)
............................................................ Less than 0.005% (at 1 kHz)
Channel separation .................................. More than 92 dB (at 1 kHz)
Wow & flutter ...................................................... Unmeasurable Limit
Output level/impedance
Chapter6
Fixed............................................................................. 2.0V/0.9 kΩ
Digital output
Optical ......................–15 dBm ~ –21 dBm (Wave length 660 nm)
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
NNootteess
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
Cahpter1
Cahpter2
Cahpter3
Cahpter4
Cahpter5
Cahpter6
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer
to the model and serial numbers whenever you call upon your dealer for
information or service on this product.
Cahpter7
Model
Serial Number
Download from Www.Somanuals.com. All Manuals Search And Download.
|