Download from Www.Somanuals.com. All Manuals Search And Download.
Installation in a vehicle
Note: Do not put Here2Anywhere in the docking station until you have completed the installation.
Installation in a vehicle (continued)
1. Determine where you want to mount 2. The leaves on the base can be bent to con-
5. Plug the cigarette lighter adapter
into the back of the cradle, as
shown. Don’t plug the adapter into
the cigarette lighter until the instal-
lation is completed.
6A. Plug the cassette adapter
6B. If your car stereo has an aux input,
plug the supplied audio cable into
the back of the cradle instead of the
cassette adapter. Plug the audio
cable’s white (L ch,) and red (R ch.)
connectors into your car stereo.
4. Using the provided screw,
assemble the docking station
cradle to the base.
Here2Anywhere.
form to curved mounting surfaces.
into the back of the cradle,
as shown.
• Do not install Here2Anywhere
where it may obstruct your view
through the windshield or your view
of your vehicle’s indicator displays.
• Do not install Here2Anywhere
where it will hinder your access to
the vehicle’s controls.
• Do not install Here2Anywhere
where it may hinder the function of
safety devices such as an airbag.
Doing so may prevent the air-bag
from functioning properly in the
event of an accident.
• Find a location that provides good
visibility of and access to
Here2Anywhere’s front panel.
3. Peel the covering away from the adhesive on
the bottom of the base and adhere it to the
mounting surface. Use the provided screws
to securely attach the base to the surface.
• If using screws, be sure that you do not
damage wiring or other systems on the
other side of the mounting surface.
• Kenwood strongly recommends
that you mount Here2Anywhere in a
location where the base can be
attached with the provided screws.
4
5
KPA-H2C Installation Guide
KPA-H2C Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation in a vehicle: Mounting the antenna
Installation in a vehicle: Routing the cable
Note: If you’re using the Kenwood CX-SR10 SIRIUS antenna, you’ll need to remove the plastic
8. Route the cable from the antenna to the vehicle’s interior by
tucking it underneath the rubber molding around rear window,
as shown below.
9. Route the cable from the lowest point of the rear win-
dow into the trunk. Take advantage of any existing
cable channels or wiring conduits.
• For SUVs, minvans & 5-door vehicles, bring the
cable into the vehicle under the rubber molding for
the tailgate, and continue under the interior trim
1. Temporarily plug the antenna
into the “1-Sat/Terr (Main)
connector on the back of the
cradle until it is firmly seated,
as shown.
housings from the antenna connectors—we recommend labeling the wires with their respective
colors. (See pg. 9, figure 16 of the CX-SR10 Installation Manual for details). Once you’ve
removed the housings, connect the wire that had the yellow connector to the connector on the
cradle labeled “1-Sat/Terr (Main)”, and connect the other one to the connector labeled “2-Terr”.
2. Find an antenna location on a metal surface at least 12” x 12”, and at least 6” from a window.
• Best reception is achieved with the antenna mounted on the roof; mounting on the trunk lid
will work for convertibles.
10. From the trunk, route the cable around the passenger
compartment and to the back of the cradle.
• If the vehicle has a roof rack or skid ribs, it may be necessary to mount the antenna off-center.
3.The antenna’s powerful magnet will secure it to the metal surface.
• Before routing the antenna cable, confirm that the antenna is mounted in a good location:
4. Temporarily plug the cigarette lighter adapter into the cigarette lighter.
5. Slide Here2Anywhere all the way into the cradle so that the connector at the rear of the unit
makes proper contact in the cradle. Press the POWER button to turn Here2Anywhere on.
6. Aim the remote control at Here2Anywhere, press the DIRECT button, then enter the number
“1-8-4”, and press the SELECT button. If your Here2Anywhere has been properly connected and
the antenna is receiving the SIRIUS signal you will hear audio. If you do not hear audio, the dis-
play will read “Acquiring Signal”. Re-orient the antenna until you hear audio. (See Antenna
Signal, on page 25 to use the ANTENNA SIGNAL screen to aim the antenna.)
• Keep the wire away from areas where it could
become tangled in driver’s and passenger’s feet.
11. Plug the antenna into the back of the cradle
(see pg. 6, Step 1).
12. Plug the cigarette lighter adapter into the cigarette
lighter.
• KENWOOD RECOMMENDS UNPLUGGING THE
CIGARETTE LIGHTER ADAPTER AFTER YOU TURN
THE VEHICLE’S IGNITION OFF. (In some vehicles,
the cigarette lighter remains active after the
ignition has been turned off, and leaving
Here2Anywhere’s cigarette lighter adapter
plugged-into the cigarette lighter could drain the
vehicle’s battery.)
• Make sure the vehicle is not in garage, or somewhere the satellite signal could be blocked
7. Turn Here2Anywhere’s power off and remove it from the cradle; unplug the cigarette lighter
adapter from the cigarette lighter; unplug the antenna from the cradle.
6
7
KPA-H2C Installation Guide
KPA-H2C Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|