COMPONENT
#840276
6.0 AMP PORTABLE JIGSAW
INSTRUCTION MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM.
YOUR FEEDBACK IS VITAL TO US.
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
PARA EL SERVICIO
PARA EL CONSUMIDOR
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
1-800-590-3723
Printed in China
840276_6.0 AMP Portable Jigsaw_Rev 8/22/06
Download from Www.Somanuals.com. All Manuals Search And Download.
WORK AREA
CAUTION
indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
Keep your work area clean and well lit.
areas may cause accidents or injury.
Cluttered work benches and dark work
CAUTION
used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust.
the dust or fumes.
Power tools create sparks which may ignite
NOTE
provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
IMPORTANT SAFEGUARDS
ELECTRICAL SAFETY
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other.) This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a polarized outlett. Do not change the
WARNING:
Some dust created by power sanding, sawing, grinding, drilling and
plug in any way.
Double insulation eliminates the need for the three wire
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
grounded power cord and grounded power supply system.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges
Some examples of these chemicals are:
• Lead from lead-based paints.
and refrigerators
. There is an increased risk of electric shock if your body is
grounded.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Don’t expose power tools to rain or wet conditions.
tool will increase the risk of electric shock.
Water entering a power
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
Do not abuse the cord. Never use the cord to carry the tool or pull the plug
from an outlet. Keep the cord away from heat, oil, sharp edges, or moving
parts. Replace damaged cords immediately
. Damaged cords increase the risk
of electric shock.
WARNING:
Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
Wash hands after handling.
When operating thee tool outside, use an outdoor extension cord marked “W-
defects or other reproductive harm.
A” or “W. ”
tric shock.
These cords are rated for outdoor use and reduce the risk of elec-
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PERSONAL SAFETY
Store idle tools out of reach of children and other untrained persons.
are dangerous in the hands of untrained users.
Tools
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained
alcohol or medication.
A moment of inattention while operating power tools
tools with a sharp cutting edge are less likely to bind and are easier to control.
may result in serious personal injury.
Check for misalignment or binding of moving parts, breakage oof parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts.
jewelry or long hair can be caught in moving parts.
Loose clothes,
serviced before using.
Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model.
Avoid accidental starting. Be sure switch is off before plugging in
. Carrying tools with
Accessories that may be suitable for one tool may create a risk of injury
your finger on the switch or plugging in tools that have the switch on invites accidents.
when used on another tool.
Remove adjusting keys or wrenches before turning the power tool “ON”.
A wrench or a key that is left attached to a rotating part of the power tool may
result in personal injury.
Use the power tool, accessories and tool bits etc., in accordance with these instruc-
tions and in thhe manner intended for the particular type of power tool, taking into
account the working conditions and the work to be performed.
Use of the power tool
for operations different form intended could result in a hazardous situation.
Do not overreach. Keep proper footing and balance at all times.
Proper footing
and balance enables better control of the power tool in unexpected situations.
SERVICE
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety
Tool service must be performed only by qualified repair personnel.
maintenance by unqualified personnel could result in a risk of injury.
shoes, hard hat or hearing protection must be used for appropriate conditions.
Service or
If devices are provided for the connection of dust extraction and collection
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual.
facilities, ensure these are connected and properrly used.
devices can reduce dust related hazards.
Use of these
Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury.
TOOL USE AND CARE
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Hold tool by insulated gripping surfaces when perform-
Use clamps or other practical ways to secure and support the workpiece to a
stable platform.
ing an operation where the cutting tool may contact hidden wiring.
Contact
Holding the work by hand or against your body is unstable and
with a “live” wire will also make exposed metal parts of the tool “live” and shock
the operator.
may lead to loss of control.
Do not force tool. Use the correct tool for your application.
The correct tool
will do the job better and safer at the rate for which it is designed.
IMPORTANT SAFETY RULES FOR JIGSAWS
Do not use the tool if the power switch does not turn it “ON” or “OFF”.
Any tool
that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the power cord plug from the power source before making any
Always wear safety goggles or other approved eye protection when using this
tool. Always use an appropriate dust mask or respirator during operations
adjustments, changing accessories or storing the tool.
Such preventive
safety measures reduce the risk of starting the tool accidentally.
where dust can be generated.
To reduce exposure to these chemicals always
work in a well ventilated area. Use approved safety equipment and dust masks
that are specially manufactured to filter out microscopic particles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
IMPORTANT:
Some of the following symbols may be used on your tool. Please
Hold the Jigsaw by the insulated gripping surfaces when performing an oper-
ation where the blade may contact hidden wiring or the tool power cord.
Contact with a "live" electrical wire will make exposed metal parts of the jigsaw
"hot" and create a potential for electrical shock to the operator. Do not cut into
existing walls or other blind areas where existing electrical wires may be pres-
ent. If this situation is necessary, remove all fuses and/or turn all circuit break-
ers off in the work area. After cuts have been completed in the blind areas,
inspect to ensure that no electrical wire was cut or nicked before reinstalling
fuses and/or engaging circuit breakers.
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SYMBOL
NAME
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
V
A
Hz
W
Kg
Volts
Amperes
Hertz
Watt
Never leave the jigsaw with the trigger left in the locked "ON" position.
Before plugging in the jigsaw, inspect to make sure the trigger lock is in the
Kilograms
Alternating Current
Direct Current
Weight
Type of Current
Type of Current
"OFF" position.
Accidentally plugging the jigsaw in with the trigger lock
engaged can result in premature starting of the tool, which can cause damage
to the tool and/or serious injury to the operator.
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Seconds
Diameter
Grounding Terminal
Denotes Double Insulation
Time
Time
Size of Drill Bits,
Keep hands away from the cutting area. Do not reach under material being
cut while the jigsaw is running.
Serious injury could occur. Always turn the jig-
min
s
saw "OFF" before inspecting the cutting area.
Do not use dull or damaged blades with the jigsaw.
Bent or damaged blades
can break or cause a kickback resulting in serious injury to the operator. Dull
blades will cause the jigsaw to perform improperly and may damage the tool.
Grinding Wheels, etc.
No load speed
Revolutions per Minute
No-load Rotational Speed
Revolutions, Surface Speed,
Strokes, etc. per Minute
Before starting to cut with the jigsaw, turn it "ON" and allow the blade to
.../min
come to full speed.
The jigsaw can chatter or vibrate if the blade speed is too slow
at the start of the cut. This can cause the jigsaw to kickback and damage the work
area or cause injury.
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
Always secure working material before attempting to make a cut with the jig-
saw.
Never hold the material with your free hand or across your legs. Small or
thin material may flex or vibrate causing loss of control and possible injury.
Make sure all adjusting screws on the jigsaw are firmly tightened.
Failure to
tighten the adjustment screws can cause the blade to disengage from its hold-
er possibly damaging the jigsaw or causing injury to the operator.
Keep the shoe flat on the work piece.
When removing the blade or other accessories from the jigsaw, avoid con-
tact with the skin. Always wear protective gloves when hhandling the jigsaw
or any accessory.
burns.
The blade can become hot after prolonged use and will cause
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING THE BLADE
FUNCTIONAL DESCRIPTION
3
1
2
16
15
7
4
5
18
17
13
14
6
11
8
10
9
12
1. Firmly grip the plastic blade guard and slide it up to expose the blade clamp.
CONTROLS AND COMPONENTS:
1. Trigger
2. Trigger Lock
3. Speed Control Adjusting Switch
4. Gear Housing
5. Blade Guard
6. Blade Holder
7. Blade
8. Roller Guide
9. Stroke Adjustment Switch
2. Using a hex wrench (provided in a slot beneath the motor), loosen the two hex
socket-head screws on the blade clamp until it slides forward enough to open a
slot for the blade.
10. Bevel Markings
11. Bevel Plate
12. Base Plate
13. Hex Wrench Storage
14. Power Cord
15. Power Cord Strain Relief
16. Vacuum Attachment
17. Hex Wrench
3. Insert the blade into the blade clamp with the cutting edge facing to the front of
the jigsaw.
4. Using a hex wrench, securely tighten the two hex socket-head screws on the
blade clamp.
5. Using a hex wrench, loosen the two hex socket-head screws holding the bottom
board and the guide roller on the saw housing.
18. Rip Fence Guide
6. Slide the guide roller forward until the back of the blade fits loosely in the center
groove. Using a hex wrench, securely tighten the two hex socket-head screws hold-
ing the guide roller and bottom board to the saw housing.
ASSEMBLY
Disconnect plug from AC power source before
assembling parts, making adjustments, or changing bladess.
Failure to
remove electrical power could cause accidental starting of the jigsaw resulting
in serious injury to the operator and/or damage to the tool.
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE JIGSAW
PENDULUM STROKE ADJUSTMENT
Together with the electronic speed
Disconnect the power plug from the AC power source
before any assembly, adjustments, or adding/removiing accessories.
Following this preventative step reduces the risk of the saw coming on acciden-
tally and the risk of damage to the workpiece and injury to the operator.
regulation, the pendulum stroke
adjustment helps to set the best
combination of blade speed and
aggressiveness needed to achieve a
desired cut rate and fineness. The
pendular knob is used to make the
adjustment. The best pendulum
stroke setting for the particular work
to be carried out can be obtained
from the following table. When using
a knife blade, the pendulum setting
should be 0. We recommend the use
of appropriate lubrication for cutting
metal.
ADJUSTING SPEED
The operating speed of the jigsaw
can be varied by using the Speed
Control Switch located on the top of
the jigsaw. Turn the speed control
from 0 to 6 to set the speed. On
most cuts, such as wood and metal,
the faster speed works best. On
other materials, such as plastic or
laminants, a slower speed might be
necessary to reduce vibration and
make smoother cuts.
Sheet metal 0
Aluminium I-II Plastic
Plywood 0- I Wood
Steel
0- I
I-II
I-III
OPERATING THE ON/OFF SWITCH
SAW SHOE/ PLATE ADJUSTMENT
Plug the jigsaw into an approved 115
V AC outlet. This tool is double
insulated and equipped with a
polarized plug (one blade is wider
than the other). Double insulation
eliminates the need for a special
three-wire grounded power supply.
Holding the jigsaw by the insulated
handle, squeeze the trigger to turn
Disconnect the unit from the power
supply. Raise the safety guard and
loosen the hex screw on the shoe
plate with the hex wrench. Pull the
shoe plate backward and set the
desired angular adjustment according
to the scale or push the shoe plate
forward for fixed Locks at 0°, 15°, 30°
or 45°. Tighten the hex screws again.
Always replace the hex wrench in the
hex wrench holder on the shoe plate
immediately after use.
ON
the jigsaw
and release the trigger
OFF
to turn the jigsaw
. Allow the
blade to reach the maximum set
speed before bringing it in contact
with the workpiece.
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DUST EXTRACTION
POCKET CUTTING
The saw blade can be inserted
directly into a wood surface with-
out first drilling a pilot hole thus
eliminating the drilling operation.
First measure and clearly mark
the surface to be cut. Then tip the
saw forward so that the Rounded
tips of the shoe rest on the work
surface, but with the blade well
clear of it. Switch on and move
the saw in its tilted position until
the moving blade is exactly over
the chosen point of entry. Lower
the rear of the shoe to the shoe
Align your blade with your cutting line. In order to improve dust extraction from the
working surface, the saw has a sawdust blowing system, which clears dust from the
cutting line. In addition, a vacuum cleaner adapter can be used to connect to an
ordinary household vacuum cleaner. The adapter is fitted into the outlet at the rear
of the jig saw. The vacuum extraction system will work most effectively when the
safety guard is in the down position.
tips with the blade exactly on the
line. Do not move the saw forward along its cut until the saw blade has
completely entered the material and the shoe comes to rest flat on the surface.
Alternatively, drill a 12mm hole to start an enclosed pocket cut.
MAINTENANCE AND CLEANING
CUTTING TIPS
CLEANING: To avoid accidents, be sure to disconnect the
tool from the electrical power source before any cleaning or maintenance.
The tool can be cleaned by using compressed dry air. If compressed air is not
available, a soft natural bristle paint brush will work. Always wear safety gog-
gles when cleaning tools with compressed air.
Place the finish side of the workpiece down and clamp it to a workbench or table.
Draw cutting lines on the back side. Place the front edge of the saw baseplate on
the workpiece and line up the blade with the line to be cut. Press the jigsaw down
firmly on the workpiece and cut slowly along the guidelines. Build up cutting speed
as you progress. If you want to leave room for finish sanding, cut slightly to the out-
side of the drawn guidelines.
Avoid using certain cleaning agents and solvents.
Chemicals like gasoline, carbon tetrachloride, acetone, paint thinner or ammo-
nia products can damage the plastic parts of the tool.
Do not force the jigsaw into the workpiece.
This could
cause the blade teeth to wear down with-out cutting or even cause the blade to
break causing damage to the jigsaw or injury to the operator. Let the saw reach
full speed before engaging the workpiece.
This power tool normally requires no maintenance, however, lubricating the guide
roller from time to time with a drop of oil will extend the life of the roller.
When the brush is worn to a certain length, the tool may stop.
When this state is reached, both brushed should be changed.
To guarantee the safety and the dependability of the product, repairing or changing
the brushes or other maintenance should be carried out by qualified service person.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
If you must use an extension cord, be suree that the gauge is large enough to carry
the amount of current necessary for your power tool.
If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
Jigsaws
Circular Saws
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
Angle Grinders
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
Reciprocating Saws
Routers
18
16
14
14
-
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
14
12
12
12
12
12
-
SPECIFICATIONS
SPECIFICATIONS
Voltage
Rated Current
Strokes per minute
Stroke length
120V
6.0A
500-3000/min
23/32"
60 Hz
Max. Cutting Thickness Wood 3 1/8"
Steel 5/16"
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
3 YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ power tool and no one else all parts
of the product (except those parts referred to below which are specifically exclud-
ed from such warranty (see Exclusions)) to be free from defects in materials and
workmanship for a period of three years from original date of purchase, except that
such warranty with regard to the battery shall be for a period of two years from
original date of purchase, unless the tool is used for commercial or rental
purposes.
SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE:
The above
warranty for this Kawasaki™ power tool, including the battery, shall be effective for
only 90 days from the original date of purchase if this tool is used for any
COMMERCIAL OR RENTAL PURPOSE.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any
other product and/or component thereof manufactured or distributed by Alltrade,
and does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
Warranty Performance
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Disclaimers
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|