COMPONENT
#691202
4 1/2" ANGLE GRINDER
INSTRUCTION MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
YOUR FEEDBACK IS VITAL TO US.
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
PARA EL SERVICIO
PARA EL CONSUMIDOR
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
1-800-590-3723
Printed in China
691202 – 4 1/2" Corded Angle Grinder-Rev 8/26/06
Download from Www.Somanuals.com. All Manuals Search And Download.
WORK AREA
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Keep your work area clean and well lit. Cluttered work benches and dark work
areas may cause accidents or injury.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
IMPORTANT SAFEGUARDS
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other.) This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a polarized outlet. Do not change the
plug in any way. Double insulation eliminates the need for the three wire
grounded power cord and grounded power supply system.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord to carry the tool or pull the plug
from an outlet. Keep the cord away from heat, oil, sharp edges, or moving
parts. Replace damaged cords immediately. Damaged cords increase the risk
of electric shock.
WARNING: Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands after handling.
When operating the tool outside, use an outdoor extension cord marked “W-
A” or “W.”These cords are rated for outdoor use and reduce the risk of elec-
tric shock.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PERSONAL SAFETY
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with a sharp cutting edge are less likely to bind and are easier to control.
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry or long hair can be caught in moving parts.
Avoid accidental starting. Be sure the switch is off before plugging in.
Carrying tools with your finger on the switch or plugging in tools that have the
switch on invites accidents.
SERVICE
Tool service must be performed only by qualified repair personnel. Service or
maintenance by unqualified personnel may result in a risk of injury.
Remove adjusting keys or wrenches before turning the power tool “ON”.
A wrench or a key that is left attached to a rotating part of the power tool may
result in personal injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury.
Do not overreach. Keep proper footing and balance at all times. Proper foot-
ing and balance enables better control of the power tool in unexpected situa-
tions.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Use safety equipment. Always wear eye protection. Dust mask, non-skid safe-
ty shoes, hard hat or hearing protection must be used for appropriate conditions.
Hold tool by insulated gripping surfaces when perform-
ing an operation where the cutting tool may contact hidden wiring. Contact
with a “live” wire will also make exposed metal parts of the tool “live” and shock
the operator.
TOOL USE AND CARE
SAFETY RULES FOR ANGLE GRINDERS
Use clamps or other practical ways to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
Never use this tool without the proper guard. The grinding wheel could shat-
ter during use. Make sure the guard covers the side of the wheel facing you.
Do not force tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
Never bounce the tool while grinding. This may crack the wheel.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that
cannot be controlled with the switch is dangerous and must be repaired.
Grinding metal will cause sparks! Keep them directed away from people and
flammable materials. Always keep the guard positioned so that as much of
the exposed disc as possible is pointing away from you.
Disconnect the power cord plug from the power source before making any
adjustments, changing accessories or storing the tool. Such preventive safe-
ty measures reduce the risk of starting the tool accidentally.
Keep children and pregnant women away from the work area until the grind-
ing is completed and the area has been cleaned up.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Always wear full eye, face and body protection. Wire bristles may break off and fly
toward the user. Always wear ear protection when grinding in enclosed spaces. Noise
level may be amplified in such locations and may cause permanent hearing loss.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Unplug Angle Grinder from power supply and place the switch in the locked
or “OFF” position before making any assembly adjustments, changing
accessories or performing any inspection, maintenance or cleaning proce-
dures. Such preventive safety measures reduce the risk of starting the tool acci-
dentally which could cause serious personal injury.
Only use grinding and cutting wheels that are approved for a maximum
speed of 13,000 rpm or greater.
After replacing a wheel or brush, always let the tool run for one minute in a
well-protected area. If the new accessory has an undetected flaw, it should
break apart in less than a minute.
Do not use the Angle Grinder if it has been damaged, left outdoors in the
rain, snow, wet or damp environments, or immersed in liquid.
Always wear an OSHA approved dusk mask or respirator when inside the
work area. Replace the filter daily. NOTE: Not all dust masks offer protection
from lead paint dust. Be sure to use the proper mask for the job.
Before connecting the tool to the power supply follow the safety instructions
for installing the grinding or cutting wheels. Do not lock the wheels too tight
or cracks may occur.
Only use grinding or cutting wheels with the correct bore size for the spindle
of the grinder.
Use standard parts. Do not use coolant or water and do not use as a fixed grinder.
Do not start the tool when the grinding or cutting wheels are touching the work area.
Keep the power cord well away from the cutting area during use. Always position
the cord so that it will not be caught in the workpiece when the grinder is in use.
Maintain labels and nameplates on the Angle Grinder. These carry important
information. If unreadable or missing, contact Alltrade for a replacement.
Always have the guards in place and properly positioned when using grind-
ing wheels or wire cup brushes.
SYMBOLS
Secure the material being grinded. Never hold it in your hand or across your
legs. Do not use your legs or feet to stabilize the workpiece. Unstable support
can cause loss of control and could result in lacerations or injury.
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
Always make sure no one, including the user, is in line with the tool when
starting the motor.
SYMBOL
NAME
Volts
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
V
A
Hz
W
Kg
Always use both hands when operating the Angle Grinder.
Always hold this tool by the insulated gripping surfaces. If this tool should
accidentally cut across its own cord or hidden wiring, all exposed metal parts
will become live and could seriously shock the user.
When using the Angle Grinder, always maintain a firm grip on the tool. Keep
your hands well away from the grinding wheel or brush. Never reach under-
neath the Angle Grinder while the sanding disk is in motion.
When the Angle Grinder is in operation, keep hands away from the cutting or
grinding area.
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Grounding Terminal
Denotes Double Insulation
Time
Time
Do not run the Angle Grinder while carrying it at your side. A moving grind-
ing wheel or brush could cause lacerations or personal injury.
min
s
The disc will not stop immediately when the Angle Grinder is turned off.
Seconds
Exercise caution.
Diameter
Size of Drill Bits,
Grinding Wheels, etc.
No-load Rotational Speed
Do not set the Angle Grinder down after use until the grinding or cutting
wheels have come to a complete stop.
No load speed
.../min
Revolutions per Minute
Revolutions, Surface Speed,
Strokes, etc. per Minute
Keep the handle of the Angle Grinder dry, clean and free from oil and grease.
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL DESCRIPTION
ATTACHING AUXILIARY HANDLE
This tool comes with an auxiliary
6
9
2
handle which can be attached to
different sides of the Angle Grinder,
depending on the preference of the
operator. This handle is necessary to
maintain complete control of the
tool and should be used at all times.
Make sure this handle is always
fastened securely.
5
1
8
7
4
3
ACCESSORIES:
8. Side Handle
CONTROLS AND COMPONENTS:
1. ON/OFF Switch
ATTACHING WHEEL GUARD
9. Pin Spanner
2. Tool Body
3. Protective Guard
4. Grinding Wheel
5. Lock-on Switch Feature
for Continuous Use
Never brush or grind without the guard in place. Brushes
are considered to be grinding wheels and must also be used with guards.
• Always unplug the tool before attempt-
ing to change the guard or accessories.
6. Spindle Lock Button
7. Power Cord
• Set the Angle Grinder on a flat surface
with the spindle facing up.
• Place the spring washer of the guard
over the spindle.
COMPONENT
Pin Spanner
MODEL NUMBER
690157
• Tighten the screw of the spring washer.
• Make sure that the guard is securely
tightened in place.
ASSEMBLY
Make sure you have full control of the tool when grinding
into a corner as a sharp, sudden movement may occur when the wheel
contacts a secondary surface.
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING WHEELS WITH DEPRESSED CENTERS
EDGE GRINDING
WARNING
WARNING
Always check the tool warning label for the recommend-
ed speed rating on accessories. Never run a wheel or brush over the rated
speed. Accessories exceeding the recommended speed may fly apart and cause
serious personal injury.
Do not use edge grinding wheels for cut-off work, deep
grinding or subject them to any side pressure as this may lead to breakage
and possible personal injury. These wheels should be used for shallow cutting
and notching (less than 1/2" in depth). Keep the open side of the guard away
from the operator at all times.
Hubbed wheels do not require mounting flanges.
Edge grinding should only be done with wheels specifically designed for this purpose.
REMOVING GUARD FOR SANDING OR USING FLAT WIRE BRUSHES
• Place the backing washer over the
spindle making sure the fit is tight.
• Set the Angle Grinder on a flat surface with the spindle facing up.
• Remove the inner and outer flanges, unscrew spring washer and remove
the guard.
• Place the grinding or cutting disc on the
top of the backing washer ensuring the
bore fits into the step of the flange.
• Store these parts carefully.
• Mount the concave recess side of the
locking nut over the spindle.
• Replace the guard after the job is finished.
ATTACHING SANDING DISC
• To remove the guard, see instructions given in the “Removing Guard for
Sanding or Using Flat Wire Brushes” Section above.
• Set the inner flange and outer flange on the spindle.
• Press the spindle lock firm and
insure there is no movement in the
spindle. Then while the spindle lock
is depressed tighten the locking nut
in a clockwise direction using the
• Push in the spindle lock button. Turn the spindle until it locks into place.
• Once the spindle is locked, tighten the sanding disc by hand.
OPERATING THE ANGLE GRINDER
pin spanner.
SPINDLE
• Allow the Angle Grinder to run in
idle for at least a minute with the
grinding or cutting disc correctly
assembled.
LOCK
Always unplug the tool before attempting to change the
guard or accessories.
BUTTON
OPERATING THE ON/OFF SWITCH
ATTACHING WIRE BRUSHES
Never switch the Angle Grinder “ON” or “OFF” while
under load conditions.
Wire cup brushes, not included, can be screwed directly on the spindle. No flanges are
necessary.
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
• Guide back and forth over the work piece in a steady motion.
• When cutting avoid tilting the Angle Grinder in the cutting plane. Ensure the cut-
ting wheel has a clean cutting edge.
Always allow the Angle Grinder to come up to full speed before touching any
surface.
• To cut hard stone a diamond cutting wheel is recommended.
• Do nut use cutting wheel for rough grinding.
Always take the tool away from the workpiece before turning the tool “OFF”.
Let the tool come to a complete stop before setting it down.
This tool operates best under light pressure. Exerting heavy pressure will not
speed up the work and may cause damage to the motor.
MAINTENANCE AND CLEANING
Always UNPLUG the tool from the power source before
cleaning or maintenance.
LOCK-ON
BUTTON
• The armature and motor are the heart of the power tool. Exercise care to ensure
they do not become damaged or effected by oil or water.
• Inspect the carbon brushes regularly and replace them when they are worn.
(about 1/3 of the way up)
• Regularly inspect all mountings and screws and ensure they are properly tight-
ened. Failure to do so may result in serious damage.
ON/OFF
SWITCH
• Consult an authorized maintenance service agent in event of damage.
• Clean and dust the Angle Grinder after each use.
• When starting hold the Angle Grinder firmly with both hands. One hand on the
rear handle or the motor housing and the other hand on the side handle.
• The switch can be locked in the “ON” position, a convenience for long grinding
• Use compressed air to blow out any accumulated dust or grit. Tiny
particles from metal grinding often accumulate inside your tool and could
create an electrical shock hazard.
operations.
• Never use solvents or harsh chemicals. Use only mild soap and a damp cloth to
clean the tool. Never let any liquid get inside the casing. Never immerse any
part of the tool in a liquid. Always keep the ventilation openings clear.
• To turn the Angle Grinder “ON” without locking it, apply pressure to the switch
button. When pressure is released, the switch button snaps to the “OFF” position.
• To lock th switch “ON”, press the switch button forward and press the lock button.
• To unlock the switch, simply press and release the lock button. Switch is spring
loaded and will snap back automatically.
• Regularly clean the ventilation slots in your tool using a soft brush or dry cloth.
ACCESSORIES
USING THE ANGLE GRINDER:
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
For best tool control, material removal and minimal
loading, keep the angle between the disc and the work surface at approxi-
mately 30° when grinding and 10°-15° when sanding.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table on next page).
• Do not cover exhaust vents when the Angle Grinder is in use. This may cause
damage to the motor and reduce efficiency.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE: The above
warranty for this Kawasaki™ power tool, including the battery, shall be effective for
only 90 days from the original date of purchase if this tool is used for any
COMMERCIAL OR RENTAL PURPOSE.
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any
other product and/or component thereof manufactured or distributed by Alltrade,
and does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
14
12
12
12
12
12
-
SPECIFICATIONS
SPECIFICATIONS
120V
Voltage
60 Hz
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
Rated Current
No-Load Speed
Maximum Disc Diameter 115mm (4-1/2")
8.0 A
11000/min
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
Angle Grinders
3 YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ power tool and no one else all parts
of the product (except those parts referred to below which are specifically exclud-
ed from such warranty (see Exclusions)) to be free from defects in materials and
workmanship for a period of three years from original date of purchase, except that
such warranty with regard to the battery shall be for a period of two years from
original date of purchase, unless the tool is used for commercial or rental
purposes.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|