Kawasaki Drill 840108 User Manual

COMPONENT

COMPOSANT

COMPONENTE

#840108

18V BATTERY-OPERATED DRILL

INSTRUCTION MANUAL

MANUEL D’INSTRUCTIONS POUR PERCEUSE

SANS FIL KAWASAKI 18 V

MANUAL DE INSTRUCCIONES PARA EL TALADRO

INALÁMBRICO DE 18V

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS

PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT

LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.

CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTES CONCERNANT LA SÉCURITÉ, LE FONCTIONNEMENT ET LE

REMISAGE DE CE PRODUIT. LIRE, ÉTUDIER ET VEILLER À BIEN COMPRENDRE TOUTES LES MISES EN GARDE ET INSTRUCTIONS

ET AUTOCOLLANTS APPOSÉS SUR LE PRODUIT AVANT DE L’UTILISER. NE PAS RESPECTER CES INSTRUCTIONS POURRAIT

ENTRAÎNER DES BLESSURES ET/OU DES DOMMAGES MATÉRIELS.

ESTE MANUAL CONTIENE INFORMACIÓN IMPORTANTE SOBRE LA SEGURIDAD, OPERACIÓN, MANTENIMIENTO Y ALMACE-

NAMIENTO DE ESTE PRODUCTO. ANTES DE USARLO, LEA Y COMPRENDA TODAS LAS PRECAUCIONES, ADVERTENCIAS,

INSTRUCCIONES Y ETIQUETAS DEL PRODUCTO. DE LO CONTRARIO PODRÍA SUFRIR LESIONES GRAVES O CAUSAR DAÑOS

MATERIALES.

IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS

PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,

HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE

REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR

COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM. YOUR FEEDBACK IS VITAL TO US.

87-1904-60957

KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™

MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR

DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE

DIRECTED TO:

POUR TOUTE QUESTION OU EN CAS DE PROBLÈME AVEC LE PRODUIT ALLTRADE, NE PAS LE RETOURNER AU MAGASIN OÙ IL

A ÉTÉ ACHETÉ. APPELER LE SERVICE APRÈS-VENTEAU 1-800-590-3723. AVANT D’APPELER, VEILLER À SE PROCURER LES

INFORMATIONS SUIVANTES : No. DE MODÈLE, DATE DE L’ACHAT ET ADRESSE DU MAGASIN. UN REPRÉSENTANT D’ALLTRADE

PEUT RÉSOUDRE VOTRE PROBLÈME PAR TÉLÉPHONE. POUR TOUT COMMENTAIRE OU SUGGESTION, N’HÉSITEZ PAS À NOUS

APPELER OU NOUS CONTACTER PAR COURRIEL À L’ADRESSE : INFO@ALLTRADETOOLS.COM. VOS COMMENTAIRES NOUS

SONT EXTRÊMEMENT PRÉCIEUX.

KAWASAKI™ EST UNE MARQUE DE COMMERCE DE KAWASAKI™

MOTORS CORP., U.S.A., QUI NE FABRIQUE PAS ET NE DISTRIBUE

PAS CE PRODUIT THIS PRODUCT. LES QUESTIONS DES CONSOM-

MATEURS DOIVENT ÊTRE ADRESSÉES À :

FOR CUSTOMER SERVICE

POUR LE SERVICE APRÉS VENTE

OU DU CONSOMMATEUR

KAWASAKI™ ES UNA MARCA REGISTRADA CON LICENCIA DE

KAWASAKI™ MOTORS CORP., E.U.A., QUE NO FABRICA NI

DISTRIBUYE ESTE PRODUCTO. LAS CONSULTAS DE LOS

CONSUMIDORES DEBEN DIRIGIRSE A:

PARA EL SERVICIO

PARA EL CONSUMIDOR

SI TIENE DUDAS O SURGEN PROBLEMAS CON SU PRODUCTO ALLTRADE, NO LO DEVUELVA A LA TIENDA LLAME A NUESTRO

DEPARTAMENTO DE SERVICIO AL CLIENTE AL 1-800-590-3723. ANTES DE LLAMAR, TENGA A MANO LA SIGUIENTE

INFORMACIÓN: No. DE MODELO, FECHA DE COMPRA Y DIRECCIÓN DE LA TIENDA. UN REPRESENTANTE DE ALLTRADE PUEDE

RESOLVER SU PROBLEMA POR TELÉFONO. SI DESEA HACER ALGUNA SUGERENCIA O COMENTARIO, LLÁMENOS O ENVÍENOS

UN MENSAJE DE CORREO ELECTRÓNICO A. INFO@ALLTRADETOOLS.COM. SUS COMENTARIOS SON FUNDAMENTALES PARA

NOSOTROS.

1-800-590-3723

Printed in China

Imprimé dans la Chine

Impreso en China

1431 VIA PLATA

LONG BEACH, CA 90810-1462 USA

840108 – 18V Black Cordless Drill, Perceuse sans fil noire, de 18 V,

Taladro inalámbrico negro de 18V_Rev 7/21/06

Download from Www.Somanuals.com. All Manuals Search And Download.

WORK AREA

WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

Keep your work area clean and well lit. Cluttered work benches and dark work

areas may cause accidents or injury.

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

Do not operate power tools in explosive areas, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite

the dust or fumes.

CAUTION used without the safety alert symbol

indicates a potentially hazardous situation which,

if not avoided, may result in property damage.

Keep bystanders, children and visitors away while operating a power tool.

Distractions can cause you to lose control.

NOTE provides additional information that is useful

for proper use and maintenance of this tool. If a

NOTE is indicated make sure it is fully understood.

ELECTRICAL SAFETY

IMPORTANT SAFEGUARDS

Do not abuse the cord. Never use the cord to carry the tool. Keep the cord

away from heat, oil, sharp edges, or moving parts. Replace damaged cords

immediately. Damaged cords may create a fire.

People with electronic devices, such as pacemakers, should consult their

physician(s) before using this product. Operation of electrical equipment in

close proximity to a heart pacemaker could cause interference or failure of

the pacemaker.

A battery operated tool with integral batteries or a separate battery pack

must be recharged only with the specified charger for the battery. A charger

that may be suitable for one type of battery may create a risk of fire when used with

another battery.

WARNING: Some dust created by power sanding, sawing, grinding, drilling and

other construction activities contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive harm.

Use battery operated tool only with specifically designated battery pack. Use of

any other batteries may create risk of fire.

Some examples of these chemicals are:

• Lead from lead-based paints.

PERSONAL SAFETY

• Crystalline silica from bricks and cement and other masonry products,

and arsenic and chromium from chemically-treated lumber.

Stay alert, watch what you are doing, and use common sense when operat-

ing a power tool. Do not use tool while tired or under the influence of drugs,

alcohol or medication. A moment of inattention while operating power tools

may result in serious personal injury.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such as dust masks that are

specially designed to filter out microscopic particles.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewelry or long hair can be caught in moving parts.

WARNING: Handling the power cord on corded products may expose you to

lead, a chemical known to the State of California to cause cancer and birth

defects or other reproductive harm. Wash hands after handling.

Avoid accidental starting. Be sure switch is in the locked or “ OFF” position

before inserting battery pack. Carrying power tools with your finger on the

switch or inserting battery pack into a tool with the power switch “ ON” invites

accidents.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE

Tool service must be performed only by qualified repair personnel. Service or

maintenance by unqualified personnel may result in a risk of injury.

Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a

key that is left attached to a rotating part of the tool may result in personal injury.

When servicing a tool, use only identical replacement parts. Follow instructions

in the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instructions may create a risk of shock or injury.

Do not overreach. Keep proper footing and balance at all times. Proper foot-

ing and balance enable better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safe-

ty shoes, hard hat, or hearing protection must be used for appropriate conditions

SPECIFIC SAFETY RULES AND/OR SYMBOLS

TOOL USE AND CARE

Hold tool by insulated gripping surfaces when perform-

ing an operation where the cutting tool may contact hidden wiring. Contact

with a “live” wire will also make exposed metal parts of the tool “live” and shock

the operator.

Use clamps or other practical ways to secure and support the workpiece to a

stable platform. Holding the work by hand or against your body is unstable and

may lead to loss of control.

SAFETY RULES FOR CORDLESS DRILL / DRIVERS

Do not force tool. Use the correct tool for your application. The correct tool

will do the job better and safer at the rate for which it is designed.

Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that

cannot be controlled with the switch is dangerous and must be repaired.

Always wear safety goggles or eye protection when using this tool. Use a dust

mask or respirator for applications which generate dust.

Disconnect battery pack from tool or place the switch in the locked or “OFF” posi-

tion before making any adjustments, changing accessories, or storing the tool.

Such preventative safety measures reduce the risk of starting the tool accidentally.

Do not grasp the tool or place your hands too close to the spinning chuck or

drill bit. Your hand may be lacerated or may cause injury.

Secure the material being worked on. Never hold it in your hand or across

your legs. Unstable support can cause loss of control and injury.

Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

Position yourself to avoid being caught between the tool or side handle and

walls or posts. Should the socket or bit become bound in the work, the reac-

tion torque of the tool could crush your hand or leg.

When battery pack is not in use, keep it away from other metal objects like:

paper clips, coins, keys, nails, screws, or other small metal objects that can

make a connection from one terminal to another. Shorting the battery termi-

nals together may cause sparks, burns or a fire.

Check to see that keys and adjusting wrenches are removed from the

Cordless Drill before switching the tool “ ON” . Keys or wrenches can fly away

at high velocity striking you or a bystander.

Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools with sharp cutting edge are less likely to bind and are easier to control.

When using the Cordless Drill, always maintain a firm grip on the tool with

both hands.

Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool’s operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

Hold tool by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring. Contact with a "live" wire

will also make exposed metal parts of the tool "live" and shock the operator.

Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may create a risk of injury

when used on another tool.

Keep the handle of the Cordless Drill dry, clean, and free from oil and grease.

Do not run the Cordless Drill while carrying it at your side. A spinning sock-

et or bit could become entangled with clothing and injury may result.

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTIONAL DESCRIPTION

Disconnect the plug or remove the battery pack from tool and place the switch

in the locked or “OFF” position before making any assembly adjustments,

changing accessories, performing any inspection, maintenance or cleaning

procedures. Such preventive safety measures reduce the risk of starting the

tool accidentally.

Do not use the Cordless Drill if it has been damaged, left outdoors in the

rain, snow, wet or damp environments, or immersed in liquid.

Maintain labels and nameplates on the Cordless Drill. These carry important

information. If unreadable or missing, contact Alltrade for a replacement.

SYMBOLS

IMPORTANT: Some of the following symbols may be used on your tool. Please

study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and safer.

CONTROLS AND COMPONENTS:

1. Battery Pack

2. Release Buttons on Each Side

3. 120V AC Adapter

4. Charger

5. LED Charging Indicators

6. 10mm (3/8") Keyless Chuck

7. 25 Adjustable Torque Settings

Control Ring

SYMBOL

NAME

EXPLANATION

8. Forward/Reversing and

Trigger Lock Lever

9. Variable Speed Controlled

Trigger Switch

10. Accessory/Bit Holder

11. Comfort Rubber Grip

ACCESSORIES:

Volts

Amperes

Hertz

Voltage (Potential)

Current

Frequency (Cycles per Second)

Power

Weight

Type of Current

Watt

Kilograms

Alternating Current

Direct Current

12. Double Ended Screwdriver Bits (2)

Alternating or Direct Current Type of Current

Earthing Terminal

Class II Construction

Minutes

Seconds

Diameter

Grounding Terminal

Denotes Double Insulation

Time

Size of Drill Bits,

COMPONENT

BATTERY PACK

120V AC ADAPTER

CHARGER

MODEL NUMBER

min

␾

690506

690074

690072

Grinding Wheels, etc.

No load speed

No-load Rotational Speed

10mm (3/8") KEYLESS CHUCK 690076

.../min

Revolutions per Minute

Revolutions, Surface Speed,

Strokes, etc. per Minute

1,2,3, …

Ring Selector Settings

Speed, Torque or Position Settings

Download from Www.Somanuals.com. All Manuals Search And Download.

BATTERY

REMOVING / ATTACHING BATTERY PACK

REMOVE BATTERY PACK:

1. Press both release buttons on either side of

the Cordless Drill to release the battery pack.

Before using battery pack, please read carefully all instruc-

tions and cautionary markings on battery pack, battery

charger and product using battery.

2. Pull battery pack free of Cordless Drill.

ATTACH BATTERY PACK:

Do not incinerate the battery pack even if it is severely dam-

1. Align the raised portion of the battery pack

with the groove in the battery compartment

of the Cordless Drill.

aged or is completely worn out. The battery pack can explode.

Do not carry battery packs in aprons, pockets, or tool

boxes, product kit boxes, drawers, etc. with loose metal objects. Battery

pack terminals could be short circuited causing damage to the battery pack,

severe burns or fire.

2. Press the battery pack into place. Make sure

the latches are securely fastened. Do not use

the Cordless Drill if the battery pack is not

seated properly.

The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic

material by the Environmental Protection Agency. Before disposing of damaged or

worn out Ni-Cad battery packs, check with your State Environmental Protection

Agency to find out about special restrictions on the disposal of these battery packs,

take them to your local recycling center for proper disposal, or call 1-800-822-8837.

RELEASE BUTTON

CHARGER

The battery is not fully charged. Before first use, the battery pack requires

8-10 hours charge time to be fully charged. Subsequent recharging needs 3-5

hours for the battery to be fully charged.

Before using battery charger, please read carefully all

instructions and cautionary markings on battery charger, battery pack and

product using battery.

Always switch to a fresh battery when tool performance begins to diminish.

Severe heat is most destructive to a battery; the more heat generated, the faster

the battery loses power. A battery that gets too hot can have a shortened life.

The charger will not automatically turn “ OFF” when the

battery pack is fully charged. The charging indicator light will remain “ ON”

until the charger is disconnected from the electrical outlet.

Never over-discharge a battery by using the tool even after tool performance

has decreased. Do not attempt to discharge a tool’s battery by continuing to

pull on the tool trigger. When tool performance begins to diminish, stop the tool

and recharge the battery for optimal performance.

Use only the charger which accompanied your product or direct replacement as

listed in this manual. Do not substitute any other charger. Use only Alltrade

approved chargers with your product.

Charge battery pack at ambient temperatures between 50° F – 104° F.

Store tool and battery pack in locations where temperatures will not exceed

120°F. This is important to prevent serious damage to the battery cells.

Do not disassemble charger.

Do not use charger if it has been damaged, left outdoors in the rain, snow, wet

or damp environments, or immersed in liquid.

The battery pack should always be recharged when the Cordless Drill begins to

run slowly.

The battery pack and charger heat during charging. Place the charger on a flat,

non-flammable surface away from flammable materials with at least four inches of

clearance to allow proper air circulation around the charger and battery pack.

When battery pack is not in use, keep it away from other metal objects such as

paper clips, coins, keys, nails, screws or other small metal objects that can

make a connection from one terminal to another. Shorting the battery terminals

together may cause sparks, burns, or fire.

When the battery pack requires recharging, a 3-5 hour charge allows the tool to

operate at full power. A charging indicator light on the charger will illuminate to

show that charging is taking place.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Hold the rear end of the chuck

in one hand and use the other

hand to rotate the front end in

a counterclockwise direction to

open the jaws of the chuck.

CHARGING BATTERY PACK

LOOSEN

TIGHTEN

CHARGE BATTERY PACK:

1. Make sure the trigger

on the Cordless Drill

is in the “ OFF” position

and remove the battery

pack from the Cordless

Drill.

BATTERY PACK

120V AC

ADAPTER

2. Insert the shank of the bit (or

other accessory) fully into the

keyless chuck, taking care to

keep the bit in the center of

the jaws of the chuck.

HOLD

2. Plug 120V AC Adapter

into household outlet

LED LIGHT

3. Turn the front end of the chuck clockwise to hold the bit in place.

and into side of battery

charger. Insert battery

4. Tighten securely by turning the front end of the chuck clockwise while holding

the rear end.

pack into battery charger.

When the battery is

placed in the charger, the

red LED indicator light will remain on.

BATTERY

CHARGER

OPERATING THE DRILL

3. When fully charged, reattach battery pack onto Cordless Drill,

making certain latches fasten securely. Cordless Drill will not

operate properly if the battery pack is not seated properly.

Never tape the trigger switch down to provide continu-

ous high speed. The tool may fail under such conditions causing fire or

personal injury.

ASSEMBLY

VARIABLE SPEED TRIGGER SWITCH

THIS TOOL IS CONTROLLED

BY A TRIGGER SWITCH:

Be aware that this tool is always in an operating condition

because it does not have to be plugged into an electrical outlet. Always turn

• The speed of the Cordless Drill depends

on the amount of pressure you put on the

the switch “ OFF” and remove the battery pack before changing bits.

trigger.

TRIGGER

SWITCH

INSTALLING DRIVE BIT INTO KEYLESS CHUCK

• The more pressure you apply, the faster

the Cordless Drill will go.

WARNING

• Release the pressure and the Cordless Drill

will slow down.

Before inserting a drill bit or other accessory, make sure the forward/reverse

and trigger lock lever is in the center “ OFF” position to prevent accidental starts

that may result in injury.

Do not attempt to tighten drill bits (or any other accessory) by gripping the

front of the chuck and turning the tool on. This may cause personal injury

and/or damage to the chuck.

When removing the bit from the tool, avoid contact with skin and use proper

protective gloves when grasping the bit or accessory. Accessories may be hot

after prolonged use.

Download from Www.Somanuals.com. All Manuals Search And Download.

FORWARD / REVERSE AND TRIGGER LOCK LEVER

SCREW DRIVING

WHEN DRIVING FASTENERS:

• Always start slowly and gradually increase the speed of the Drill.

Be sure the trigger is released when changing the position of the lever.

Always store the tool in the “ LOCKED/OFF” position.

• Release the trigger when you feel the clutch slip.

• Always keep the driver bit straight to prevent damage to the screw.

• Hold the Drill with both hands to ensure control if the bit should stick or slip.

Always check the direction of the Cordless Drill's rotation before use.

• To prevent wood from splitting, drill pilot holes into the wood before driving

in the screws.

TO SELECT THE DIRECTIONS

OF ROTATION:

• To select forward Cordless Drill

rotation, press the trigger lock

from left to right flat against the Cordless

DRILLING METAL

TRIGGER

LOCK

Drill body.

WHEN DRILLING HARD METALS:

• Apply a lubricant, such as cutting oil, to the tip of the bit.

• To select reverse, press the trigger lock lever

in the opposite direction.

• Start with a small hole then enlarge to the required size. Make sure the bit is

actually cutting and not spinning in the hole as this will dull the edges of the bit.

• The center position locks the tool.

• Keep enough pressure on the bit to keep it drilling through the material.

TORQUE SETTINGS

DRILLING MASONRY

WHEN DRILLING MASONRY:

To prevent damaging the tool or driving screw too deep

• Masonry can be brittle so be careful not to apply too much pressure and crack

the material.

into work piece, release the trigger when you feel the clutch slip.

• Apply enough pressure to keep the bit cutting and not spinning in the hole as this

will dull the edges of the bit.

THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE:

• For light duty work, use lower settings.

CONTROL RING

• Bricks and similar soft materials will require less pressure, concrete will require

much more.

• For heavy duty work, use higher settings.

PROPER SETTING FOR DRIVING SCREWS:

1. Set the ring on the lowest

setting to begin.

DRILLING WOOD

2. Try tightening the first screw.

If the drill drives smoothly,

proceed with the next screw.

Use twist bits to drill holes in wood. Make sure the bits are sharp. Pull the bits

out of the hole frequently to clear chips from the flutes as an overburdened bit

may overheat.

3. If the Drill’s clutch slips,

increase the torque setting

and try again until the Drill

drives the screw without incident.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use only mild soap and a damp cloth to clean the tool. Never let any liquid get

inside the casing. Never immerse any part of the tool in a liquid. Always keep the

ventilation openings clear.

HINTS FOR OPTIMUM USE

DRILLING:

• Keep the right amount of pressure in a straight line with the drill bit. Too little and

the bit will spin without cutting, too much and the motor may stall.

Always clean the battery pack using only a dry cloth. Do not use liquids.

Always unplug the charger before cleaning it.

• Just before the drill tip breaks though the other side of the work piece drill more

slowly and decrease pressure on the tool. This will prevent stalling and leave a

cleaner hole.

Regularly clean the ventilation slots in your tool and charger using only a soft

brush or dry cloth.

• Use a block of wood to back up work pieces that may splinter.

• Use spade bits when drilling large diameter holes in wood.

• Use HSS drill bits when drilling in metal.

Never open the Cordless Drill case, battery pack or charger. Do not attempt to

repair the Cordless Drill, battery pack or charger yourself. Opening any of these

parts will void your warranty.

• Use masonry bits when drilling in soft masonry.

ACCESSORIES

• Use a lubricant when drilling metals other than cast iron, aluminum, copper,

and brass.

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may become hazardous when used on

another tool.

• When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent

slipping at higher speeds.

Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.

• Never try to start a stalled Drill by clicking the trigger switch “ ON” and “ OFF” .

If you must use an extension cord, be sure that the gauge is large enough to carry

the amount of current necessary for your power tool. If not, your tool may experi-

ence a loss of power, excessive voltage drop or overheating. The smaller the gauge

number, the heavier the cord (see table on next page).

This may damage your tool.

• To reduce jamming, always keep the Drill running when pulling the bit out of a

finished hole.

SCREWDRIVING:

• Always use the correct type and size of screwdriver bit.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS

TOOL CURRENT RATING

CONDUCTOR SIZE IN A.W.G

• If screws are difficult to tighten, try applying a small amount of washing liquid or

soap as a lubricant.

AMPERE

3-6

10FT.

25FT.

50FT.

100FT.

• Always hold the tool and screwdriver bit in a straight line with the screw.

6-8

8-10

MAINTENANCE AND CLEANING

10-12

12-16

16-20

Always remove the battery pack before attempting

cleaning or maintenance.

This Cordless Drill is lubricated before it leaves the

factory. This lubrication should last for the life of the tool. No further

lubrication is required.

Download from Www.Somanuals.com. All Manuals Search And Download.

USE WARRANTY. This tool is made for home use in the execution of

projects and repairs in and around the home. Use of the tool for COMMERCIAL

PURPOSES OR ON A JOBSITE is not covered under this warranty.

SPECIFICATIONS

Voltage

18V

The date of purchase shall be the date of shipment to the original purchaser, or the

date the original purchaser took possession, custody or control of the product,

whichever occurred first. This warranty shall be null and void if the product or any

component thereof is modified, altered or used for any commercial purpose or on

a jobsite. This warranty does not apply to any other product and/or component

thereof manufactured or distributed by Alltrade, and does not apply to products

and/or components thereof designed, manufactured and/or assembled by others,

for which Alltrade makes no warranties whatsoever. THERE ARE NO WARRANTIES

WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.

Speed

0-600/min.

25 Drill

␾ 10mm (3/8")

120V

Approx. 3-5 hours

Ni-Cad

Torque Settings

Chuck Capacity (max)

Charger Input

Charging Time

Battery Type

60Hz

PROTECTING THE ENVIRONMENT

Warranty Performance

BATTERIES

By purchasing the product, purchaser expressly acknowledges and agrees that their

sole and exclusive remedy under this warranty shall be strictly limited to the repair

or replacement of any covered nonconforming items or parts thereof provided that

any such nonconforming item and/or part is promptly returned to Alltrade’s facility

postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,

1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)

within the applicable warranty period, with a written request by purchaser that

Alltrade repair and/or replace the nonconforming item and/or part. We recommend

that you keep the original product packaging in the event you need to ship the unit.

We suggest the package be insured against loss or in transit damage. When

sending your product include your name, address, phone number, dated proof

of purchase (or copy), and a statement about the nature of problem. Warranty

coverage is conditioned upon purchaser furnishing Alltrade with adequate written

proof that they are the original purchaser and of the original purchase date. Parts

returned, freight prepaid and insured, to Alltrade’s facility (see above address) will

be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if

found to be defective and subject to warranty. Alltrade retains the sole discretion

to determine whether any item or part is nonconforming and, if so, whether the

item and/or part will be repaired and/or replaced. If the unit is repaired, new or

reconditioned replacement parts may be used. If Alltrade chooses to replace

the product, it may replace it with a new or reconditioned one of the same or

comparable design. The repaired or replaced unit will be warranted under the terms

of the remainder of the warranty period. Typically, a defective product that is

returned within the first 30 days after the purchase date will be replaced; for items

returned after the first 30 days and within the warranty period, covered defective

parts not subject to normal wear and tear or other exclusions will be repaired or

replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-

ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-

conforming item and/or part thereof shall constitute fulfillment of all

Alltrade batteries can be recharged many times. At the end of their useful life,

recycle batteries with due care for our environment.

Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center

or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.

OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS

Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would

like further information on the following products, please contact Alltrade Customer

Service Department at 1-800-590-3723.

Cordless Drills/Screwdrivers

Impact Wrenches

Sanders

Angle Grinders

Reciprocating Saws

Routers

Jigsaws

Rotary Tools

Circular Saws

Corded and Cordless Multi-Purpose Tools

Wide Range of Accessories and more

2 YEAR LIMITED HOME USE WARRANTY

Express and Exclusive Limited Home Use Warranty to Original Retail Buyer

Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail

purchaser of the accompanying KAWASAKI™ portable power tool and no one else

all parts of the product (except those parts referred to below which are specifically

excluded from such warranty (see Exclusions)) to be free from defects in materials

and workmanship for a period of two years from original date of purchase.

SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS: This

Kawasaki™ portable power tool is offered as a home use tool and carries a HOME

Download from Www.Somanuals.com. All Manuals Search And Download.

obligations to the purchaser. Alltrade shall not be responsible or liable for any

expense, including freight charges, or repairs made outside Alltrade’s facility, unless

expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade

bear any responsibility for loss of the unit, loss of time or rental, inconvenience,

commercial loss or consequential damages.

EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE

WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR

IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE

AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,

PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT

THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,

GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY

OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF

ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING

BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY

EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.

PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH

WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING

THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE

REMEDY IS AS STATED ABOVE.

Exclusions

This warranty does not cover parts damaged due to normal wear, abnormal

conditions, misapplication, misuse, abuse, accidents, operation at other than

recommended pressures or temperatures, improper storage or freight damage.

Parts damaged or worn by operation in dusty environments are not warranted.

Failure to follow recommended operating and maintenance procedures also

voids warranty.

This limited warranty does not apply to accessory items such as drill bits,

screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding

sheets and other related items.

DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,

NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS

OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,

USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,

COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO

PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS

WARRANTY.

Limitation Of Liability

IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR

INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY

KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH

OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS

REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,

AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR

OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS

REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH

DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,

WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL

ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF

THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF

THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY

PERIODS SPECIFIED ABOVE.

Alltrade will not be liable for the following: labor charges, loss or damage resulting

from improper operation, maintenance or repairs made by other persons;

pre-delivery services such as assembly, oil or lubricants, and adjustment;

maintenance services that are normally required to maintain the product.

The use of other than genuine Alltrade Repair Parts will void warranty.

Warranty Disclaimers

EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,

GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY

PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR

REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING

THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE

PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF

WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,

WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY

ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE

BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE

AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY

WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR

CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S

SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.

Limitations on Warranty Disclaimers

Some states do not allow limitations on how long an implied warranty lasts

and some states do not allow the exclusion or limitation of the incidental or

consequential damages, so part or all of the above limitations or exclusions may not

apply to you. This warranty gives you specific legal rights, and you may also have

other rights which vary from state to state.

If your product is not covered by this warranty, please call our Customer Service

Department toll free at 1-800-590-3723 for general repair information and charges.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPONENT

#840108

18V BATTERY-OPERATED WORKLIGHT

INSTRUCTION MANUAL

FOR CUSTOMER SERVICE

POUR LE SERVICE APRÉS VENTE

OU DU CONSOMMATEUR

87-1904-60957

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS

PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT

LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.

PARA EL SERVICIO

PARA EL CONSUMIDOR

KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™

MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR

DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE

DIRECTED TO:

IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS

PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,

HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE

REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR

COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM. YOUR FEEDBACK IS VITAL TO US.

1-800-590-3723

Printed in China

Imprimé dans la Chine French

Impreso en China Spanish

1431 VIA PLATA

LONG BEACH, CA 90810-1462 USA

840108 – 18V Black Cordless Worklight

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

CONGRATULATIONS!

Thanks for choosing this product. At Alltrade, our aim is to provide you with quality

products at an affordable price, and we want you to be totally satisfied with your

product and our Customer Service. If any help and advice is needed, please

years of satisfaction.

CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INTENDED USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SECTION ONE

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . . . . . 2-3

IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SECTION TWO

INTENDED USE

SAFETY RULES FOR WORKLIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SECTION THREE

This tool is intended for consumer use only. Your charger and/or adapter has been

designed for charging batteries of the type approved and supplied with this tool.

BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

REMOVING / ATTACHING BATTERY PACK . . . . . . . . . . . . . . . . . . . 5

CHARGER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CHARGING BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SECTION FOUR

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to

follow all instructions listed below may result in electric shock, fire and/or

serious personal injury.

SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

OPERATING THE ON/OFF SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . 9

ADJUSTING THE WORKLIGHT BEAM . . . . . . . . . . . . . . . . . . . . . . 9

REPLACING THE LIGHT BULB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10

SECTION FIVE

The safety instructions provided in this manual are not intended to cover all possible

conditions and practices that may occur when operating, maintaining and cleaning

power tools.

Always use common sense and pay particular attention to all the DANGER,

WARNING, CAUTION and NOTE statements of this manual.

MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PROTECTING THE ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS . . . . . . . . . . . . . . 12

SECTION SIX

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

!DANGER indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

2 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-16

!WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY RULES FOR WORKLIGHT

!CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

Use battery operated tool only with specifically designated

battery pack. Use of any other batteries may create risk of fire.

CAUTION used without the safety alert symbol

indicates a potentially hazardous situation which,

if not avoided, may result in property damage.

Keep the handle of the Worklight dry, clean, and free from oil and grease.

Do not run the Worklight while carrying it at your side. The worklight heats up

immediately when in use and could result in burns.

NOTE provides additional information that is useful

for proper use and maintenance of this tool. If a

NOTE is indicated make sure it is fully understood.

Do not use the Worklight if it has been damaged, left outdoors in the rain, snow,

wet or damp environments, or immersed in liquid.

Maintain labels and nameplates on the Worklight. These carry important informa-

tion. If unreadable or missing, contact Alltrade for a replacement.

IMPORTANT SAFEGUARDS

Battery pack must be recharged only with the specified charger for the battery. A

charger that may be suitable for one type of battery may create a risk of fire when used

with another battery.

People with electronic devices, such as pacemakers, should consult their

physician(s) before using this product. Operation of electrical equipment in

close proximity to a heart pacemaker could cause interference or failure of

the pacemaker.

Do not use in a damp or wet environment.

Store out of reach of children and other untrained persons.

WARNING: Some dust created by power sanding, sawing, grinding, drilling and

other construction activities contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive harm.

BATTERY

Some examples of these chemicals are:

• Lead from lead-based paints.

Before using battery pack, please read carefully all instructions and cautionary

markings on battery pack, battery charger and product using battery.

• Crystalline silica from bricks and cement and other masonry products,

and arsenic and chromium from chemically-treated lumber.

Do not incinerate the battery pack even if it is severely damaged or is

completely worn out. The battery pack can explode.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such as dust masks that are

specially designed to filter out microscopic particles.

Do not carry battery packs in aprons, pockets, or tool boxes, product kit

boxes, drawers, etc. with loose metal objects. Battery pack terminals could

be short circuited causing damage to the battery pack, severe burns or fire.

The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic

material by the Environmental Protection Agency. Before disposing of dam-

aged or worn out Ni-Cad battery packs, check with your State Environmental

Protection Agency to find out about special restrictions on the disposal of these

battery packs, take them to your local recycling center for proper disposal, or

call 1-800-CLEANUP.

WARNING: Handling the power cord on this product may expose you to lead, a

chemical known to the State of California to cause cancer and birth defects or

other reproductive harm. Wash hands after handling.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Download from Www.Somanuals.com. All Manuals Search And Download.

CHARGER

The battery is not fully charged. Before first use, the battery pack requires

8-10 hours charge time to be fully charged. Subsequent recharging needs 3-5

hours for the battery to be fully charged.

Before using battery charger, please read carefully all

instructions and cautionary markings on battery charger, battery pack and

product using battery.

Always switch to a fresh battery when tool performance begins to diminish.

Severe heat is most destructive to a battery; the more heat generated, the faster

the battery loses power. A battery that gets too hot can have a shortened life.

The charger will not automatically turn “ OFF” when the

battery pack is fully charged. The charging indicator light will remain “ ON”

until the charger is disconnected from the electrical outlet.

Never over-discharge a battery by using the tool even after tool performance

has decreased. Do not attempt to discharge a tool’s battery by continuing to

pull on the tool trigger. When tool performance begins to diminish, stop the tool

and recharge the battery for optimal performance.

Use only the charger which accompanied your product or direct replacement as

listed in this manual. Do not substitute any other charger. Use only Alltrade

approved chargers with your product.

Charge battery pack at ambient temperatures between 50° F – 104° F.

Do not disassemble charger.

Store tool and battery pack in locations where temperatures will not exceed

120°F. This is important to prevent serious damage to the battery cells.

Do not use charger if it has been damaged, left outdoors in the rain, snow, wet

or damp environments, or immersed in liquid.

The battery pack should always be recharged when the Cordless Worklight

begins to dim.

The battery pack and charger heat during charging. Place the charger on a flat,

non-flammable surface away from flammable materials with at least four inches of

clearance to allow proper air circulation around the charger and battery pack.

When battery pack is not in use, keep it away from other metal objects such as

paper clips, coins, keys, nails, screws or other small metal objects that can

make a connection from one terminal to another. Shorting the battery terminals

together may cause sparks, burns, or fire.

When the battery pack requires recharging, a 3-5 hour charge allows the tool to

operate at full power. A charging indicator light on the charger will illuminate to

show that charging is taking place.

REMOVING / ATTACHING BATTERY PACK

REMOVE BATTERY PACK:

1. Press both release buttons on either side

of the Cordless Worklight to release the

battery pack.

2. Pull battery pack free of Cordless Worklight.

ATTACH BATTERY PACK:

1. Align the raised portion of the battery pack

with the groove in the battery compartment

of the Cordless Worklight.

2. Press the battery pack into place. Make

sure the latches are securely fastened.

Do not use the Cordless Worklight if the

battery pack is not seated properly.

RELEASE

BUTTON

Download from Www.Somanuals.com. All Manuals Search And Download.

CHARGING BATTERY PACK

SYMBOL

NAME

EXPLANATION

␾

Diameter

Size of Drill Bits,

Grinding Wheels, etc.

No-load Rotational Speed

Revolutions, Surface Speed,

Strokes, etc. per Minute

BATTERY PACK

CHARGE BATTERY PACK:

1. Make sure the trigger on

the Cordless Worklight

is in the “ OFF” position

and remove the battery

pack from the Cordless

Worklight.

No load speed

Revolutions per Minute

.../min

120V AC

ADAPTER

1,2,3, …

Ring Selector Settings

Speed, Torque or Position Settings

2. Plug the 120V AC adapter

into household outlet

OPERATING INSTRUCTIONS

Parts of this Worklight heat up almost immediately when

in use. To avoid burns, use caution when handling light bulb and metal reflector.

Never change a hot light bulb. Bulb must be cool to the touch before attempting

to remove or replace it.

LED LIGHT

and into side of battery

charger. Insert battery

pack into battery charger.

LED light will turn green

when battery pack is fully

charged (approx. 3 hours).

BATTERY

CHARGER

3. When fully charged, reattach battery pack onto Cordless Worklight, making

certain latches fasten securely. Cordless Worklight will not operate properly

if the battery pack is not seated properly.

SYMBOLS

IMPORTANT: Some of the following symbols may be used on your tool. Please

study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and safer.

SYMBOL

NAME

Volts

Amperes

Hertz

Watt

Kilograms

Alternating Current

Direct Current

EXPLANATION

Voltage (Potential)

Current

Frequency (Cycles per Second)

Power

Weight

Type of Current

CONTROLS AND COMPONENTS:

1. Battery Pack

2. Release Buttons on Each Side

3. 120V AC Adapter

6. ON/OFF Switch

7. Reflector Rim

ACCESSORIES:

4. Charger

8. Replacement Light bulb (inside unit)

Alternating or Direct Current Type of Current

5. LED Charging Indicators

Earthing Terminal

Class II Construction

Minutes

Grounding Terminal

Denotes Double Insulation

Time

COMPONENT

BATTERY PACK

120V ADAPTER

CHARGER

MODEL NUMBER

min

690506

690074

690072

Seconds

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Remove the battery pack from the

Worklight.

OPERATING THE ON / OFF SWITCH

REPLACEMENT

BULB

Press the “ ON/OFF” switch to turn the worklight “ ON” and “ OFF” .

2. Hold the top of the Worklight with

one hand while twisting the rim in a

counter-clockwise direction with the

other. Continue turning until the rim

comes loose.

ADJUSTING THE WORKLIGHT BEAM

Hold the handle of the Worklight securely in

one hand. With the other hand, swivel the

3. Remove the bulb by turning it

slightly and pulling it out of the bulb

fitting. Be careful not to damage the

delicate parts inside the case.

head of the Worklight counter-clockwise

until it is at the angle you desire. Swivel the

head of the Worklight clockwise to return it

to its original position.

4. Insert the new bulb, then carefully

put the rim back in place and turn

it clockwise to tighten it.

MAINTENANCE AND CLEANING

Always remove the battery pack before attempting

cleaning or maintenance.

REPLACING THE LIGHT BULB

Use only mild soap and a damp cloth to clean the tool. Never let any liquid get

inside the casing. Never immerse any part of the tool in a liquid. Always keep the

ventilation openings clear.

This Worklight uses a Krypton 18V, 0.6 A light bulb. Use of any other kind of

light bulb may cause damage or injury.

Always clean the battery pack using only a dry cloth. Do not use liquids.

Always unplug the charger before cleaning it.

Parts of this worklight heat up almost immediately when in use. To avoid

burns, use caution when handling light bulb and metal reflector. Never change

a hot light bulb. Bulb must be cool to the touch before attempting to remove or

replace it.

Regularly clean the ventilation slots in your tool and charger using only a soft

brush or dry cloth.

Never open the Worklight case, battery pack or charger. Do not attempt to repair

the Worklight, battery pack or charger yourself. Opening any of these parts will void

your warranty.

For your convenience, a spare light bulb is included

inside the unit. Unscrew the rim and carefully remove it from the light

assembly.

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

SERVICE

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may become hazardous when used on

another tool.

Use only authorized replacement parts for your tool.

Equipment service must be performed only by qualified repair personnel using

authorized replacement parts. Service or maintenance by unqualified personnel

could result in considerable risk of personal injury. Use of unauthorized parts or fail-

ure to follow maintenance instructions may create a risk of electric shock or injury.

Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.

If you must use an extension cord, be sure that the gauge is large enough to carry

the amount of current necessary for your power tool. If not, your tool may

experience a loss of power, excessive voltage drop or overheating. The smaller the

gauge number, the heavier the cord (see table below).

PROTECTING THE ENVIRONMENT

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS

BATTERIES

TOOL CURRENT RATING

CONDUCTOR SIZE IN A.W.G

Alltrade batteries can be recharged many times. At the end of their useful life, recy-

cle batteries with due care for our environment.

AMPERE

3-6

6-8

8-10

10-12

12-16

16-20

10FT.

25FT.

50FT.

100FT.

Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center

or call 1-800-CLEANUP. Collected batteries will be recycled or disposed of properly.

OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS

Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would

like further information on the following products, please contact Alltrade Customer

Service Department at 1-800-590-3723.

SPECIFICATIONS

Cordless Drills/Screwdrivers

Impact Wrenches

Sanders

SPECIFICATIONS

Voltage

Light Bulb Type

Charger Input

Charging Time

Battery Type

18V

Krypton 18V 0.6 A

120V 60Hz

Approx. 3-5 Hour