COMPONENT
#840557
4 1/2" ANGLE GRINDER
INSTRUCTION MANUAL
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
87-1904-60957
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS
PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
PARA EL SERVICIO
PARA EL CONSUMIDOR
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS
PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,
HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR
COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM. YOUR FEEDBACK IS VITAL TO US.
1-800-590-3723
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
Printed in China
Imprimé dans la Chine
Impreso en China
840557 – 4-1/2" Corded Angle Grinder - Rev. 3/31/06
Download from Www.Somanuals.com. All Manuals Search And Download.
WORK AREA
CAUTION
used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Keep your work area clean and well lit.
areas may cause accidents or injury.
Cluttered work benches and dark work
NOTE
provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust.
the dust or fumes.
Power tools create sparks which may ignite
IMPORTANT SAFEGUARDS
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
WARNING:
Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
immediately.
Damaged cords may create a fire.
PERSONAL SAFETY
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
WARNING:
Handling the power cord on this product may expose you to lead, a
chemical known to the State of California to cause cancer and birth defects or
Wash hands after handling.
Keep your hair, clothing, and gloves away from moving parts.
jewelry or long hair can be caught in moving parts.
Loose clothes,
other reproductive harm.
Remove adjusting keys or wrenches before turning the power tool “ON”.
A wrench or a key that is left attached to a rotating part of the power tool may
result in personal injury.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Do not overreach. Keep proper footing and balance at all times.
Proper foot-
ing and balance enables better control of the power tool in unexpected situa-
tions.
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safe-
ty shoes, hard hat or hearing protection must be used for appropriate conditions.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOL USE AND CARE
SAFETY RULES FOR ANGLE GRINDERS
Never use this tool without the proper guard.
shatter during use. Make sure the guard covers the side of the wheel facing you.
The grinding wheel could
Use clamps or other practical ways to secure and support the workpiece to a
stable platform.
Holding the work by hand or against your body is unstable and
may lead to loss of control.
Never bounce the tool while grinding. This may crack the wheel.
Do not force tool. Use the correct tool for your application.
The correct tool
will do the job better and safer at the rate for which it is designed.
Grinding metal will cause sparks! Keep them directed
away from people and flammable materials. Always keep the guard
positioned so that as much of the exposed disc as possible is pointing away
from you.
Do not use the tool if the power switch does not turn it “ON” or “OFF”.
that cannot be controlled with the switch is dangerous and must be repaired.
A tool
Disconnect the power cord plug from the power source before making any
adjustments, changing accessories or storing the tool.
ty measures reduce the risk of starting the tool accidentally.
Such preventive safe-
Keep children and pregnant women away from the work area until the grinding
is completed and the area has been cleaned up.
Store idle tools out of reach of children and other untrained persons.
are dangerous in the hands of untrained users.
Tools
Always wear full eye, face and body protection.
Wire bristles may break off and fly
toward the user. Always wear ear protection when grinding in enclosed spaces. Noise
level may be amplified in such locations and may cause permanent hearing loss.
Maintain tools with care. Keep cutting tools sharp and clean.
tools with a sharp cutting edge are less likely to bind and are easier to control.
Properly maintained
Always wear an OSHA approved dusk mask or respirator when inside the work
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that mayy affect the tool’s operation. If damaged, have the tool
area.
Replace the filter daily. NOTE: Not all dust masks offer protection from lead
paint dust. Be sure to use the proper mask for the job.
serviced before using.
Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model.
Always have the guards in pplace and properly positioned when using grinding
wheels or wire cup brushes.
Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
Secure the material being grinded. Never hold it in your hand or across your
legs.
Do not use your legs or feet to stabilize the workpiece. Unstable support can
cause loss of control and could result in lacerations or injury.
SERVICE
Always make sure no one, including the user, is in line with the tool when starting
the motor.
Tool service must be performed only by qualified repair personnel.
maintenance by unqualified personnel may result in a risk of injury.
Service or
Always hold this tool by the insulated gripping surfaces.
accidentally cut across its own cord or hidden wiring, all exposed metal parts will
become live and could seriously shock the user.
If this tool should
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual.
follow Maintenance Instructions may create a risk of shock or injury.
Use of unauthorized parts or failure to
Do not run the Angle Grinder while carrying it at your side.
wheel or brush could cause lacerations or personal injury.
A moving grinding
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Keep the handle of the Angle Grinder dry, clean and free from oil and grease.
Hold tool by insulated gripping surfaces when perform-
Unplug Angle Grinder from power supply and place the switch in the locked or
“OFF” position before making any assembly adjustments, changing accessories
ing an operation where the cutting tool may contact hidden wiring.
Contact
with a “live” wire will also make exposed metal parts of the tool “live” and shock
the operator.
or performing any inspection, maintenance or cleaning procedures.
Such
preventive safety measures reduce the risk of starting the tool accidentally which
could cause serious personal injury.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
After replacing a wheel or brush, always let the tool run for one minute in a
well-protected area.
FUNCTIONAL DESCRIPTION
If the new accessory has an undetected flaw, it should break
apart in less than a minute.
4
Do not use the Angle Grinder if it has been damaged, left outdoors in the rain,
snow, wet or damp eenvironments, or immersed in liquid.
Maintain labels and nameplates on the Angle Grinder.
information. If unreadable or missing, contact Alltrade for a replacement.
These carry important
5
When using the Angle Grinder, always maintain a firm grip on the tool.
hands well away from the grinding wheel or brush. Never reach underneath the
Angle Grinder while the sanding disk is in motion.
Keep your
1
6
2
3
7
8
SYMBOLS
IMPORTANT:
Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
ACCESSORIES:
7. Grinding Wheel
8. Wrench
CONTROLS AND COMPONENTS:
1. ON/OFF Switch
2. Tool Body
3. Protective Guard
4. Anti Vibration Side Handle
5. Lock-on Switch Feature
for Continuous Use
SYMBOL
NAME
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
V
A
Hz
W
Kg
Volts
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
6. Replaceable Brush Cap
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Grounding Terminal
Denotes Double Insulation
Time
Time
COMPONENT
WRENCH
MODEL NUMBER
690157
min
s
Seconds
ASSEMBLY
Make sure you have full control of the tool when grinding
Diameter
Size of Drill Bits,
Grinding Wheels, etc.
No-load Rotational Speed
No load speed
into a corner as a sharp, sudden movement may occur when the wheel
contacts a secondary surface.
.../min
Revolutions per Minute
Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING AUXILIARY HANDLE
This tool comes with an auxiliary
ATTACHING WHEELS WITH DEPRESSED CENTERS
WARNING
Always check the tool warning label for the recommend-
ed speed rating on accessories.
handle which can be attached to
either side of the Angle Grinder,
depending on the preference of the
operator. This handle is necessary
to maintain complete control of
the tool and should be used at all
times. Make sure this handle is
always fastened securely.
Never run a wheel or brush over the rated
speed. Accessories exceeding the recommended speed may fly apart and cause
serious personal injury.
Hubbed wheels do not require mounting flanges.
ATTACHING WHEEL GUARD
Never brush or grind without the guard in place.
Brushes
are considered to be grinding wheels and must also be used with guards.
SPINDLE
LOCK
BUTTON
• Always unplug the tool before attempting to change the guard or accessories.
• Set the Angle Grinder on a flat surface with the spindle facing up.
• Place the spring washer of the guard over the spindle.
• Tighten the screw of the spring washer.
• Check to make sure that the guard is fitted properly. Put the inner flange on
the spindle.
• Put the grinding wheel on the spindle and the inner flange.
• When working with thin grinding wheels, fit the threaded outer flange with the
raised area facing toward the wheel.
• Make sure that the guard is securely tightened in place.
• When working with thick grinding wheels, fit the threaded outer flange with
the raised area facing away from the wheel.
• Push in the spindle lock button. Turn the outer flange until it locks into place.
• Once the spindle is locked, insert the enclosed wrench into the holes of the outer
flange to tighten the outer flange properly.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING WIRE BRUSHES
OPERATING THE ANGLE GRINDER
Wire cup brushes, not included, can be screwed directly on the spindle. No flanges are
necessary.
Always unplug the tool before attempting to change the
guard or accessories.
EDGE GRINDING
For best tool control, material removal and minimal
loading, keep the angle between the disc and the work surface at approximate-
ly 30° when grinding and 10°-15° when sanding.
WARNING
Do not use edge grinding wheels for cut-off work, deep
grinding or subject them to any side pressure as this may lead to breakage
and possible personal injury.
These wheels should be used for shallow cutting
and notching (less than 1/2" in depth). Keep the open side of the guard away
from the operator at all times.
OPERATING THE ON/OFF SWITCH
Edge grinding should only be done with wheels specifically designed for this purpose.
Never switch the Angle Grinder “ON” or “OFF” while
under load conditions.
REMOVING GUARD FOR SANDING OR USING FLAT WIRE BRUSHES
• Set the Angle Grinder on a flat surface with the spindle facing up.
Always allow the Angle Grinder to come up to full speed before touching any
surface.
• Remove the inner and outer flanges, unscrew spring washer and remove
the guard.
Always take the tool away from the workpiece before turning the tool “OFF”.
Let the tool come to a complete stop before setting it down.
• Store these parts carefully.
• Replace the guard after the job is finished.
This tool operates best under light pressure.
Exerting heavy pressure will not
speed up the work and may cause damage to the motor.
ATTACHING SANDING DISC
Press the “ON/OOFF” switch to start the tool.
LOCK-ON
BUTTON
• To remove the guard, see instructions given in the “Removing Guard for Sanding
or Using Flat Wire Brushes” Section above.
To stop, release the “ON/OFF” switch.
When continuous operation
is desired, press the
• Set the inner flange and outer flange on the spindle.
“ON/OFF”
switch forward
• Push in the spindle lock button. Turn the spindle until it locks into place.
• Once the spindle is locked, tighten the sanding disc by hand.
and depress the lock-on but-
ton. This locks the switch
ON/OFF
SWITCH
“ON”
until the lock-on but-
ton is released.
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND CLEANING
SPECIFICATIONS
SPECIFICATIONS
Always UNPLUG the tool from the power source before
cleaning or maintenance.
Voltage
120V
60 Hz
Rated Current
No-Load Speed
5.8 A
11000/min
Use compressed air to blow out any accumulated dust or grit.
•
•
Tiny
particles from metal grinding often accumulate inside your tool and could
create an electrical shock hazard.
Maximum Disc Diameter 115mm (4-1/2")
Never use solvents or harsh chemicals.
Use only mild soap and a damp cloth to
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
clean the tool. Never let any liquid get inside the casing. Never immerse any part of
the tool in a liquid. Always keep the ventilation openings clear.
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
• Regularly clean the ventilation slots in your tool using a soft brush or dry cloth.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Jigsaws
Circular Saws
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
Angle Grinders
If you must use an extension cord, be suree that the gauge is large enough to carry
the amount of current necessary for your power tool.
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
If not, your tool may experi-
Reciprocating Saws
Routers
Rotary Tools
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
50FT.
18
100FT.
18
16
14
14
-
18
18
18
18
16
14
14
12
12
12
12
12
-
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
3 YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ power tool and no one else all parts
of the product (except those parts referred to below which are specifically exclud-
ed from such warranty (see Exclusions)) to be free from defects in materials and
workmanship for a period of three years from original date of purchase, except that
such warranty with regard to the battery shall be for a period of two years from
original date of purchase, unless the tool is used for commercial or rental
purposes.
SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE:
The above
warranty for this Kawasaki™ power tool, including the battery, shall be effective for
only 90 days from the original date of purchase if this tool is used for any
COMMERCIAL OR RENTAL PURPOSE.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any
other product and/or component thereof manufactured or distributed by Alltrade,
and does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
Warranty Performance
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Disclaimers
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|