Kathrein Satellite TV System UFS 712si User Manual

Operating manual

DVB Satellite Receiver

UFS 712si/712sw

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT INFORMATION

The channels available on the satellites and transponders are subject to continual change. If changes

do occur, the new channels have to be set in the receiver because the factory preset programming

corresponds to the status on the date of manufacture. The information for these settings can be found on

the Internet or in relevant magazines.

Your receiver is factory ﬁtted with the latest software version. We are, however, constantly working on

adapting the software in response to the wishes of our customers and to developments in technology.

The “Software Update” section provides more information on this.

Please keep the original packaging in case you need to return the product at any time!

If the product is not properly packed, the warranty claim is invalidated.

Make a note of the receiver‘s basic settings, so as to be able to restore them if necessary!

DiSEqC™ is a trademark of Eutelsat.

UFO micro is a trademark of KATHREIN-Werke KG.

DISPOSAL INSTRUCTIONS

Electronic equipment is not domestic waste - in accordance with directive 2002/96/EC

OF THE EUROPEAN PARLIAMENT AND THE COUNCIL dated 27^thJanuary 2003 on used

electrical and electronic appliances, it must be disposed of properly.

At the end of its service life, take this unit for disposal to an appropriate ofﬁcial collection

point.

Used batteries are special waste!

Do not throw spent batteries into your domestic waste; take them to a collection point for

old batteries!

SWITCHING OFF THE RECEIVER AND UPDATING THE EPG

^{By pressing the}ꢀ^{button you can switch the receiver out of TV mode and into standby mode. Pressing any}

of the numeric buttons returns it from standby mode into operating mode.

Every night at 03:00 the receiver automatically starts to update the EPG data. This updates the EPG data

for the ﬁrst 25 channels of the overall channel list. This update happens however only if the receiver is in

standby mode. If the receiver is completely switched off (at the mains) or if it is in operation, the update will

be delayed. The receiver will update the EPG data when it is next switched from operating mode into standby

mode. After updating the data, the receiver automatically switches back to standby. You can however by

^{pressing the}ꢀ^{button break off the update before it is ﬁnished; the receiver then switches immediately into}

standby mode.

REFERENCE NOTE ON AUDIO MPEG INC. AND S.I.SV.EL, S.P.A:

This device employs legally protected technologies which are protected by patents in the USA as well as by

intangible property laws in other countries.

Audio MPEG Inc. and Societa‘ Italiana per lo sviluppo dell‘elettronica, S.I.SV.EL, S.P.A, have granted

KATHREIN-Werke KG rights of use which are subject to certain restrictions. These restrictions must also be

observed by you as a customer.

According to these, this device is only to be used by end customers for private, non-commercial purposes

and for licensed content. Use for commercial purposes is not authorised. Utilisation of products or proce-

dures sold or used with this device are not comprehended. With reference to licensed technologies, applica-

tion of reversible procedures as well as dismantling of the device are both not permitted.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

PREFACE ................................................................................................................................. 2

IMPORTANT INFORMATION...................................................................................................... 3

CONTENTS............................................................................................................................... 4

SAFETY INSTRUCTIONS - IMPORTANT NOTES ........................................................................ 6

RECEIVER FEATURES/SCOPE OF SUPPLY............................................................................... 7

CONTROLS, DISPLAYS AND CONNECTIONS............................................................................ 8

CONNECTION AND SET-UP ...................................................................................................... 9

REMOTE CONTROL................................................................................................................. 11

FIRST INSTALLATION............................................................................................................. 13

OPERATING INSTRUCTIONS .................................................................................................. 20

MENU CONCEPT .................................................................................................................. 20

MENU TREE ......................................................................................................................... 21

ALPHANUMERIC INPUTS...................................................................................................... 22

LANGUAGE SELECTION - OSD ............................................................................................. 22

ON-SCREEN DISPLAYS (OSD) ................................................................................................ 23

CHANNEL MESSAGES.......................................................................................................... 23

CHANNEL INFORMATION...................................................................................................... 23

OPTION SELECTION............................................................................................................. 23

ERROR SIGNALLING ............................................................................................................ 24

CHANNEL LIST - TV/RADIO ................................................................................................... 24

EPG - ELECTRONIC PROGRAMME GUIDE.............................................................................. 26

CALL UP EPG ....................................................................................................................... 26

“CURRENT” VIEW ................................................................................................................. 27

“COMING UP” VIEW (PROGRAMME LISTINGS) ...................................................................... 28

CATEGORIES VIEW .............................................................................................................. 29

SCAN FUNCTION.................................................................................................................. 30

ADDITIONAL INFORMATION (i-BUTTON)................................................................................ 31

RECORDING (TIMER)............................................................................................................ 32

RECORD ONCE................................................................................................................... 33

RECORD DAILY ................................................................................................................... 33

RECORD WEEKLY ............................................................................................................... 34

RECORD USER-DEFINED...................................................................................................... 34

SERIES RECORDING ........................................................................................................... 35

VIEW RECORDING SCHEDULE............................................................................................. 36

COMMON INTERFACE ............................................................................................................ 37

IMPORTANT INFORMATION .................................................................................................. 37

INSERTING THE SMARTCARD AND THE CA MODULE ........................................................... 37

VIDEOTEXT (TELETEXT)......................................................................................................... 39

EDIT CHANNEL LIST............................................................................................................... 40

SELECTION OF THE LIST/CHANNELS TO BE EDITED............................................................ 40

EDITING LISTS/CHANNELS................................................................................................... 41

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

“LAST FUNCTION” MEMORY.................................................................................................. 42

MOVE CHANNELS ............................................................................................................... 42

DELETE CHANNELS............................................................................................................. 42

SKIP CHANNELS ................................................................................................................. 42

LOCK CHANNELS ................................................................................................................ 43

COPY CHANNELS TO THE FAVOURITES LIST........................................................................... 43

START BLOCK HIGHLIGHTING (HIGHLIGHTING SEVEREAL CHANNELS) ....................................... 43

EDIT FAVOURITES LISTS ...................................................................................................... 44

REMOVE FROM THE FAVOURITES LIST .................................................................................. 44

LOCK CHANNELS ................................................................................................................ 45

RENAME FAVOURITE LIST .................................................................................................... 45

START BLOCK HIGHLIGHTING (HIGHLIGHTING SEVEREAL CHANNELS) ....................................... 45

CHANNEL SEARCH (CHANNEL SCAN) ................................................................................... 46

AUTOMATIC (CHANNEL) SCAN ............................................................................................. 46

MANUAL (CHANNEL) SCAN................................................................................................... 48

CHANNEL SCAN WITH SERVICE ID....................................................................................... 50

PARENTAL CONTROL............................................................................................................. 52

BLOCKING THE MAIN MENU................................................................................................. 52

BLOCKING THE RECEIVER................................................................................................... 52

SETTING A NEW CODE (PIN)................................................................................................. 53

SETTINGS .............................................................................................................................. 54

TV SETTINGS ....................................................................................................................... 55

CONFIGURING THE ON-SCREEN MENU ............................................................................... 56

DATE AND TIME.................................................................................................................... 58

COMMON INTERFACE .......................................................................................................... 58

ANTENNA CONFIGURATION ................................................................................................. 58

SERVICE MENU...................................................................................................................... 59

UPDATE SOFTWARE ............................................................................................................ 59

FACTORY DEFAULT .............................................................................................................. 61

CONNECTING UP THE VIDEO/PVR ......................................................................................... 62

RECORDING......................................................................................................................... 62

PLAYBACK............................................................................................................................ 62

USING THE FRONT PANEL ..................................................................................................... 63

TECHNICAL APPENDIX........................................................................................................... 64

TECHNICAL FEATURES ........................................................................................................ 64

SCART SOCKET ASSIGNMENT ............................................................................................. 66

VHS/S-VHS SWITCHING........................................................................................................ 66

CONNECTION EXAMPLE....................................................................................................... 67

SHORT TECHNICAL GUIDE .................................................................................................... 68

GLOSSARY........................................................................................................................... 70

TROUBLESHOOTING.............................................................................................................. 71

SERVICE .............................................................................................................................. 71

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY INSTRUCTIONS - IMPORTANT NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

RECEIVER FEATURES/SCOPE OF SUPPLY

The UFS 712si and UFS 712sw receivers are suitable for receiving FTA digital satellite TV and radio

channels.

The integral Common Interface offers capacity for two CA modules for further pay-TV channels.

In addition to providing high-quality pictures and sound, series 712 receivers also feature an attractive

design in a modern case.

Despite their small size, the receivers have a comprehensive range of features, such as electrical

and optical audio output for Dolby Digital (AC 3), videotext (Teletext) with memory for 800 pages,

a 16-character alphanumeric display for channel names, radio data and transmitter information.

PRODUCT PACKAGE

UFS 712si (silver) or UFS 712sw (black)

Remote control RC 660

Scart cable

2 batteries AAA 1.5 V

Power supply cable

Operating manual

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROLS, DISPLAYS AND CONNECTIONS

This section provides a brief description of all the controls, displays and connections.

VIEW OF FRONT PANEL (FLAP FOLDED DOWN)

ꢁ

ꢃ

ꢂ

VIEW OF REAR PANEL

ꢁ ꢂ ꢃ

ꢄ ꢉ

ꢅ

ꢆ

ꢇ

ꢁꢈ

Rear panel controls and displays

Front panel controls and displays

1. LNB input

1. On/Off switch (with mains disconnect)

2. Display (cover folded down)

3. Common Interface for two

2. Optical data stream output (SPDIF/

Sony Philips Digital Interface Format)

for Dolby Digital AC 3 audio

)

CA modules for Pay-TV cards *

3. LNB loop-through input

4. Ejection button for CA modules

4. Audio outputs (L/R) - cinch sockets

5. Video output (composite colour)

6. Electrical data stream output (SPDIF/

Sony Philips Digital Interface Format)

for Dolby Digital AC 3 audio

In addition there are three further

buttons on the front of the display

TV/R button for switching between

TV and radio mode

7. Scart socket for TV connection

Channel select buttons (▼▲)

8. Scart socket for VCR/AUX connection

9. RJ 11 data interface

10. Mains power cable

)

* CA modules and Pay TV cards (smart cards) are not included

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTION AND SET-UP

The following section is intended speciﬁcally for specialist dealers. You only need to pay attention to this

section if you are carrying out the installation yourself.

The “Connection examples” section provides a sample conﬁguration.

Do not connect the unit to the mains until all installation work has been properly carried out. Refer to the

information in the “Safety instructions” section.

CONNECTING THE UNIT (SAT-IF CONNECTIONS)

Connect the Sat IF inputs on the receiver to the satellite reception system. Use

a coaxial cable with a standard F connector.

If the F standard connectors are not yet ﬁtted on the cable, strip the insulation from

the cable as shown in the following illustration and carefully twist the F standard

connectors on to the ends of the cables until they are securely seated.

When ﬁtting the connector, make sure that no wires from the braid are touching

the inner conductor, so no short circuit can occur.

The quality of the reception signal depends on the connection!

RECEPTION REQUIREMENTS

Make sure that your own satellite antenna system is equipped at least with

a universal LNB for digital reception in the high-band range.

RECEPTION SYSTEM PRESETS

The presets for the control signals have been made for standard reception systems, i.e. 14/18 V for

polarity reversal and 22 kHz switching signal for low/high band changeover on multi-feed reception

systems.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTION AND SET-UP

TV AND VIDEO RECORDER CONNECTION

Connect the satellite receiver (TV Scart socket) to the TV set using a Scart cable (see “Connection

example”). If your TV has a stereo feature, you can receive the sound in stereo via the Scart connection.

Use a further Scart cable to connect the satellite receiver (VCR/Scart socket) to the video recorder/PVR.

For system reasons, the same video signals are to be found at the TV Scart socket as at the video cinch

output.

If you are recording using an external video recorder, remember not to operate the

receiver during recording, otherwise all the on-screen displays will appear on your

recording.

AUDIO CONNECTION

If you want to play the sound on your hi-ﬁ system, connect the audio cinch sockets to the input sockets

on the hi-ﬁ system, using an appropriate cable (see “Connection Example”).

OPTICAL/ELECTRICAL DIGITAL OUTPUT

The ﬁbre-optic output and the electrical digital output are intended for the connection of a Dolby Digital

system (see “Connection Example”).

INSERTING BATTERIES INTO THE REMOTE CONTROL

Remove the cover on the rear of the remote control.

Insert the two supplied batteries into the remote control. Ensure correct polarity of the batteries;

the + and – markings are indicated inside the battery compartment.

Slide the cover back into the housing until it locks in place.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL

ꢊ

ꢀ

Sound on/off

Stand-by

...

ꢑ

ꢈ ꢇ

Videotext (Teletext)

Switch on/input digits for

channels, timer etc.

(yellow)

Call up channel options

sound/subtitles selection

ꢋ

Call up the main menu,

exit the menu and return

to the TV picture

(blue)

Switch between TV/radio

(red)

Call up favourites selection

ꢒ

Call up channel messages

channel information

(green)

“Current” view in the EPG

ꢈ

AV mode

Volume

Channel selection

ꢌ

up/down

Exit menu

step by step

ꢓ

Input conﬁrmation

call up channel list

ꢍ

Changing channel in the

programme guide (EPG)

ꢔ ꢕ ꢖ ꢗ

Cursor buttons

ꢎ

Transparent videotext

ꢘ

Call up EPG

(programme guide)

ꢏ

Currently not used

ꢙ

(red)

ꢐ

Changing channel in the

Recording in EPG,

programme guide (EPG)

editing in channel list

ꢚ

Stop recording/

The button symbols shown here can also be found in the

description of the operating steps.

playback

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL

REMOTE CONTROL RC 660

The RC 660 remote control supports up to four devices (which are supplied with the RC 660 as standard)

as well as the receivers of the UFD 5xx (not UFD 552, 554, 558) and UFD 4xx families.

First switch all receivers off at the power switch.

To conﬁgure a receiver to an infrared code:

Switch on the relevant receiver.

On the remote control simultaneously press

^{Address 1 =}ꢌ ⁺ꢇ ⁺ꢁ^.

^{Then switch the receiver off again at the power switch and do the same for the other units (}ꢌ ⁺ꢇ ⁺ꢂ

^{for the second receiver;}ꢌ ⁺ꢇ ⁺ꢃ ^{for the third receiver and}ꢌ ⁺ꢇ ⁺

for the fourth receiver).

Make sure only one receiver is on at a time!

To switch the remote control to an infrared code:

When you have conﬁgured all receivers to their infrared code, to switch between units on the remote

control do the following:

^{For the ﬁrst receiver‘s remote (address 1) press}ꢌ ꢁ; for the second receiver ꢌ ꢂ;

^{for the third receiver}ꢌ ⁺ꢃ; and for the fourth receiver ꢌ ⁺

(red) = Kathrein UFD 5xx code for remote control RC 400

ꢌ ⁺

The RC 600 and RC 650 remote controls cannot be replaced!

Download from Www.Somanuals.com. All Manuals Search And Download.

FIRST INSTALLATION

Before using your unit for the ﬁrst time, read the “Safety Instructions” and “Connection

and Set-Up” sections.

The “Connection examples” section provides a sample conﬁguration.

Do not connect the unit to the mains until all installation work has been properly

carried out.

The guidance given in the “First Installation” section assumes that the receiver

has been properly connected, as per the “Safety Instructions” and “Connection

and Set-Up” sections.

First switch your TV set on and select the AV channel slot. Switch on your receiver at the power switch

on the rear of the unit. The following display appears:

Also pay attention to the bars

at the bottom of the on-screen

display! This provides hints on

what to do next.

Select the menu language you want using the

French, Italian, Spanish, Czech, Dutch and Turkish.

buttons. Available options: German, English,

ꢖꢕ

Press (green) to move to the next menu.

The following display appears:

Note:

If you are unsure whether you chose the right option from a previous menu, you can go

back a step at any time during the ﬁrst installation process by pressing the (red) button.

Download from Www.Somanuals.com. All Manuals Search And Download.

FIRST INSTALLATION

^{Use the}ꢕꢖꢔꢗ ^{buttons here to select the settings for your TV set.}

When doing this, refer to the operating instructions for your TV set!

TV format

Select the TV‘s picture format. Either

4:3 or

16:9

Screen display

Here you select the type of screen display, depending on the setting of your TV format:

TV format “4:3”: Pan & Scan or Letterbox

TV format “16:9”: Always 16:9 or automatic

TV Scart signal output

Select the type of video signal at the TV Scart socket here. Select the signal that your TV set can process.

CVBS – Colour Video Baseband Signal

RGB – Red/Green/Blue signal or

Y/C – S-Video signal (luminance/chrominance)

Press (green) to move to the next menu.

The following display appears:

Download from Www.Somanuals.com. All Manuals Search And Download.

FIRST INSTALLATION

When selecting the satellite(s),

make sure that your reception

position is aligned to the desired

satellite(s)!

DiSEqC™ Switch

Select the setting here to match your reception system using the

system is DiSEqC™-capable, select “ON” at the “DiSEqC™ switch” selection (allows switch-over from

receiving one satellite to receiving another one). If your reception system is DiSEqC™-capable, allow the

buttons. If your reception

ꢔꢗ

^{default setting “OFF” to remain. Press the}ꢖ ^{button to move to the next menu item.}

For ease of understanding, the further explanations of the ﬁrst installation are split into two columns.

The description on the left refers to installation of a non-DiSEqC™-capable system and on the

right to installation of a DiSEqC™-capable system.

Satellite and position

Use the buttons to select the desired

Number of satellites

ꢔꢗ

^{Press the}ꢗ ^{button to select the satellite to be}

satellite whose signal is to be received by the tuner.

received.

When you have selected your desired satellite, use

The following display appears:

^theꢕꢖ ^{buttons to switch to the selection of the}

“LNB type”.

Download from Www.Somanuals.com. All Manuals Search And Download.

FIRST INSTALLATION

Use the

buttons to select how many

LNB settings

ꢔꢗ

satellites (max. 4) you would like to receive with your

reception system. The following display appears

(example):

Here use the

type used in your system. The choice is between

buttons to select the LNB

ꢔꢗ

“Universal” and “User-deﬁned”.

Universal:

No further input required, since all necessary

frequency ranges are covered by a universal LNB.

User-deﬁned:

If you choose not to use a universal LNB, you must

here set the frequency ranges for which your LNB

has been conﬁgured.

Use the

buttons to select the frequency

ꢕꢖ

range to be changed (low, high or limit frequency).

^{Use the}ꢔꢗ ^{buttons or the digital input buttons}

to set the exact frequency for which your LNB was

conﬁgured.

Use the

buttons to select the ﬁrst

ꢕꢖ

satellite slot. Press

to access the menu

ꢓ

Test transponder

for the satellite settings. The following display

appears (example):

To check whether the settings that you have

made are correct, use the

to move to the “Test transponder” ﬁeld.

buttons

ꢕꢖ

Use the buttons to select the required

ꢔꢗ

transponder from the various ones listed. If your

settings are correct, you will see at the top right

of the screen the live signal of a channel for the

currently selected transponder.

If you are not receiving a signal, check your

settings again and if necessary call for expert

help.

Download from Www.Somanuals.com. All Manuals Search And Download.

FIRST INSTALLATION

Satellites and position

^{Use the}ꢔꢗ ^{buttons to set the desired satellite}

(selection from 17 pre-programmed options).

LNB settings

Here use the

type used in your system. The choice is between

buttons to select the LNB

ꢔꢗ

“Universal” and “User-deﬁned”.

Universal:

No further input required, since all necessary

frequency ranges are covered by a universal LNB.

User-deﬁned:

If you choose not to use a universal LNB, you must

here set the frequency ranges for which your LNB

was conﬁgured.

Use the

buttons to select the frequency

ꢕꢖ

range to be changed (low, high or limit frequency).

Use the buttons or the digital input

ꢔꢗ

buttons to set the exact frequency for which your

LNB was conﬁgured.

Test transponder

To check whether the settings that you have

made are correct, use the

to move to the “Test transponder” ﬁeld.

buttons

ꢕꢖ

Use the buttons to select the required

ꢔꢗ

transponder from the various ones listed. If your

settings are correct, you will see at the top right of the

screen the live signal of a channel for the currently

selected transponder.

If you are not receiving a signal, check your

settings again and if necessary call for expert

help.

You have now completed all settings for the ﬁrst

satellite. Press the

“Satellite Selection Menu” and perform the settings

in the same way for the remaining satellites.

button to return to the

ꢌ

The notes on ﬁrst installation are uniﬁed once again from this point!

When you have ﬁnished conﬁguring the satellite press (green) button. The receiver then automatically

calls up the selection menu for the channel search.

Download from Www.Somanuals.com. All Manuals Search And Download.

FIRST INSTALLATION

Perform channel scan

Use the buttons to select (yes or no) whether you wish to start a channel scan. It is not

ꢔꢗ

essential to start a channel scan, instead you can use the factory pre-programmed channels. However

the channels do change from time to time (e.g. their frequencies change), which the receiver does not

automatically detect, and can then be found only by performing a channel scan.

If you selected “NO”, you can press the

installation.

(green) button to skip directly to the next item of the ﬁrst

^{If you selected “YES”, you can press the}ꢖ ^{button to progress to the next selection item.}

Channel scan mode

^{Use the}ꢔꢗ ^{buttons to select whether you wish to scan “only free and encrypted”, “only free” or}

“only encrypted” channels.

To view encrypted channels you need the appropriate CA (Conditional Access) module and a

valid smart card together with a valid subscription to a Pay-TV provider.

^{Press the}ꢖ ^{button to move to the next selection item.}

Network search

If you set the network search to “Off”, only the factory stored transponders of the satellites you previously

selected will be scanned for new and as yet unlisted channels.

If you set the network search to “On”, the transponder network enables additional transponders that

have not yet been saved to be located. They are then stored and scanned for new channels in the same

way as the existing transponders.

Press the

(green) button to start the channel scan, or if you set channel scan to “Off” you are guided

straight to the next item in the ﬁrst installation process.

When the scan has been completed, you will see the following message (example):

Download from Www.Somanuals.com. All Manuals Search And Download.

FIRST INSTALLATION

^{Use the}ꢓ ^{button to move to the next step of the ﬁrst installation. The following display appears:}

Set Local Time

Use the

Germany +1 hour).

buttons to set the time zone variation from UTC (formerly GMT) (e.g. for

ꢔꢗ

Use the

buttons to switch to the “Automatic Time Setting” ﬁeld. Use the

buttons

ꢕꢖ

ꢔꢗ

to select whether the receiver should automatically change over to and from summer and

winter time. If “On” is selected, the receiver automatically sets itself to the right time. If “Off”

is selected, the ﬁeld for manual selection of summer and winter time is displayed below.

^{Use the}ꢔꢗ ^{buttons to perform the setting.}

Press the (green) button to close ﬁrst installation and return to the main menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING INSTRUCTIONS

MENU CONCEPT

The structure of the menu concept is based on logical operating sequences. The programme showing on

the current selected channel always appears in the top right-hand corner of the screen.

You will ﬁnd detailed descriptions of the selected menu items in the relevant sections of the

operating manual.

Note:

The selected menus, sub-menus and positions, as well as the parameters to be set, are

each highlighted in colour. The menus are self-explanatory.

Pay attention to the bar at the

bottom of the on-screen display! This

provides hints on what to do next.

^{Press the}ꢋ ^{button to access the main menu, and use the}ꢕꢖ ^{buttons to select the sub-menus.}

^{Press the}ꢓ ^{button to access the sub-menus. Use the}ꢕꢖ ^{buttons to select the sub-menu options.}

^{The settings under the various options are made either by pressing the}ꢔꢗ ^{buttons or using the}

numeric pad. You can exit the main menu and sub-menus, and the various options, step-by-step by

^{pressing the}ꢌ ^{button (the settings/changes you made are saved). Press}ꢋ ^{to return directly from}

one of the menus to the TV picture (the settings/changes you made are saved).

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING INSTRUCTIONS

MENU TREE

Main menu

^{Call up the menu by pressing the}ꢋ ^button

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING INSTRUCTIONS

ALPHANUMERIC INPUTS

Use the displayed keypad (see ﬁgure to the right) for

entry of favourites names or search terms by selecting

numerals for the desired letters/digits. You can write

button). Use the

numeric pad to select the desired character. About two

seconds after selection of the character, the cursor moves

^{with upper or lower case letters (}ꢋ

^{automatically to the next position. The}ꢔ ^{button allows}

you to delete your entry character by character.

^{When you have selected all the characters, press the}ꢓ

button to save your entry and start a scan to ﬁnd the desired

expression.

LANGUAGE SELECTION - OSD

The language for the on-screen display is set as follows:

ꢋ ^→ꢕꢖ ^{→ Language selection →}ꢓ ^→ꢕꢖ ^{→ German →}

ꢓ

Available options: German, English, Italian, French, Dutch, Spanish, Czech and Turkish.

^{After you have performed the settings, press the}ꢋ ^orꢌ ^{button to exit the main menu. You will then}

return to the TV picture.

Download from Www.Somanuals.com. All Manuals Search And Download.

ON-SCREEN DISPLAYS (OSD)

CHANNEL MESSAGES

TV CHANNEL MESSAGES

$ = Encrypted

channel

Channel

names

Videotext/Teletext

available

Selected

favourites list

Time

Channel

number from

the overall list

Number of

soundtracks

(yellow)

button

Time progression bar for

the current programme

Display of start time for current

and next programmes

Channel information is shown for a few seconds each time the channel is changed (this can be

^{changed under “Settings”, “Adjust Displays”) or displayed continuously by pressing the}ꢒ ^button.

RADIO CHANNEL MESSAGES

The information for the current radio channel has the same layout.

CHANNEL INFORMATION

^Pressꢒ ^{twice to view information on the current channel, if transmitted by the channel provider. Use the}

ꢕꢖ ^{buttons to scroll through the pages. By pressing the}ꢔꢗ ^{buttons you can obtain information on}

^{the next following programmes on the current channel. Press the}ꢒ ^orꢌ ^{button to exit the display.}

OPTION SELECTION

Press the

(yellow) button once to view further soundtrack selection options, if these are transmitted

^{by the channel provider. Use the}ꢕꢖ ^{buttons to scroll through the available selection options. Press}

the

^{(yellow) button again, or press the}ꢌ ^{button to exit this display again.}

Download from Www.Somanuals.com. All Manuals Search And Download.

ON-SCREEN DISPLAYS (OSD)

ERROR SIGNALLING

“Weak or no signal” indicates that an error has occurred in the reception system or in the receiver settings,

or that the transponder is not sending.

Check the Sat IF connection and the LNB conﬁguration. If you have changed settings, compare them

against the basic settings (provided you had made a note of them as suggested).

CHANNEL LIST - TV/RADIO

Also pay attention to the bars

at the bottom of the on-screen

display! This provides hints on

what to do next.

^{Press the}ꢓ ^{button to access the channel list.}

Calling this up displays the channel selection/sorting list from which you selected the last channel.

At the top right you will see the selected channel list (TV or radio channels) displayed.

Press the (blue) button to switch between the TV and radio channel lists.

To the right of it you see the current channel list sort order as selected by you.

Download from Www.Somanuals.com. All Manuals Search And Download.

ON-SCREEN DISPLAYS (OSD)

The channel list can show channels sorted by various selection and sorting criteria.

Selection and sorting options:

Press the

through the existing favourites lists.

^{(red) button to call up the favourites list selection. The}ꢍꢙ ^{buttons allow you to scroll}

Press the (green) button to return to the overall list (all satellites). Use the

to choose between the received satellites (display all channels from a satellite) and the list of

“New channels” (provided by channel scan).

buttons

ꢍꢙ

Press the

(yellow) button to see an alphabetic listing. This shows all the channels sorted

^{alphabetically, or the ones beginning with the selected initial letter. Use the}ꢍꢙ ^{buttons to make}

the selection.

Search function:

Press the

button to start the search. The numeric pad buttons allow you to input the

ꢑ

desired search expression for the channel that is sought (see also “Operating instructions”,

“Alphanumeric input”). Press the

example of a search result).

button to start the search (see screenshot below for an

ꢓ

^Pressꢒ ^{to view the following items of information on a channel (see screenshot on the right as an}

example):

Signal strength

Signal quality

Transmitting satellite

Frequency (MHz)

Polarisation

Symbol rate

^{The cursor buttons (}ꢕꢖꢔꢗ^{) are used to navigate within the respective channel list view to select}

^{the desired channel. The selection of the desired channel is conﬁrmed by pressing the}ꢓ ^{button. You}

will now hear and view the currently selected channel in the small window at the top right. To exit the

^{channel list and return to the TV picture, press the}ꢓ ^{button again, or press the}ꢌ ^button.

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

CALL UP EPG

^{The EPG is called up by pressing the}ꢘ ^{button. Each time the EPG is called up, you will automatically}

be shown the “Current” view, irrespective of which view you were shown the last time you exited the EPG.

The following display appears (example):

Today’s date

and time

Selected

EPG view

Current picture

on the selected

channel

Channel

number from

the overall list,

channel

name, current

programme

with progress

bar

Day of the

week and

period of time

in which the

highlighted

programme

is showing

Date and

time of the

highlighted

programme

with category,

duration and

picture format

At this place you will be shown the age

limitation of the highlighted programme, if

this is supplied by the channel provider

Note:

If you had selected a favourites list before calling up the EPG, you will see in the EPG

^{only the data for the channels that are included in your channel list. Press the}ꢘ ^button

a second time to view the EPG for all channels.

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

Selection options:

(red) button

Calls up the recording schedule (display of all pre-programmed

recordings)

Jump the “Current” view forwards by 15 minutes

ꢙ ^button

Call up a preview of the currently highlighted channel

(yellow) button

Call up the category selection (sorting the programmes by categories such as

movies, sport, series ...)

(blue) button

button

(P+) jump forwards 24 hours in the EPG, (P-) jump backwards 24 hours in

the EPG (e.g. into “Current” and into “Coming up”)

ꢓ ^button

^{Selects the currently highlighted channel in all views. Pressing the}ꢓ ^orꢌ

button again closes the EPG and the selected channel is shown again on

the TV screen

Adds a programme to the recording settings

ꢐ ^{(red dot) button}

ꢑ ^button

Search for a particular programme or programme content (input the search

expression using the numeric pad on the remote control, see also the section

“Operating instructions”, “Alphanumeric input”)

If present, shows further information on the selected programme

ꢒ ^button

^{Navigation within each view is always performed using the cursor buttons (}ꢕꢖꢔꢗ^).

The

buttons allow you to select individual channels/programmes, and the

buttons

ꢕꢖ

ꢔꢗ

allow you to scroll from page to page of the currently selected list.

^{Pressing the}ꢘ ^orꢌ ^{buttons exits the EPG again and returns to the TV picture.}

You see information on the current or next following programmes in the EPG only

if it is supplied by the channel provider. If no EPG data are available the receiver,

instead of showing information on the current programme, shows the message

“No data available”.

“CURRENT” VIEW

The “Current” view can be called up at any time in EPG by pressing the

automatically displayed every time the EPG is started (see screenshot “Calling up EPG”).

(green) button. This is then

In the “Current” view you see all channels displayed in the order of the overall channel list. Provided that

EPG data has been supplied by the channel provider, the receiver shows for each channel the current

programme being shown, with start time, ﬁnish time, and progression bar.

^{You can use the cursor buttons (}ꢕꢖꢔꢗ^{) or the keypad buttons to select the desired channel}

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

^{and if available you can use the}ꢒ ^{button to call up further information on the desired programme.}

^Theꢙ ^{button allows you to look ahead in 15 minute steps to future programmes for the channels}

^{(press the}ꢍ ^{button to return to the current time).}

If you wish to view the programme currently being shown on a channel, you need not exit the EPG,

^{just select the desired channel and press the}ꢓ ^{button. At the top right of the screen you will see the}

^{current TV picture for the selected channel. The picture however only appears once the}ꢓ ^{button has}

been pressed – previously what you saw was the picture of the old channel that had previously been

selected, even though the EPG was no longer set to that channel.

“COMING UP” VIEW (PROGRAMME LISTINGS)

The “Coming up” view (programme listings) can be called up at any time in EPG by pressing

the (yellow) button.

Also pay attention to the bars

at the bottom of the on-screen

display! This provides hints on

what to do next.

In the “Coming up” view you will see all the programmes that will be shown in the previous “Current” list

of selected channels. Provided that EPG data has been supplied by the channel provider, the receiver

shows the programmes that will be shown on the selected channel for several days in advance.

^{You can use the cursor buttons (}ꢕꢖꢔꢗ^{) to select the desired programme and if available you can}

^{use the}ꢒ ^{button to call up further information on the desired programme.}

^{You can use the}ꢍꢙ ^{buttons to scroll through the channels in the order of the overall channel list}

(the channels can also be selected by inputting digits with the keypad); you remain however in “Coming

up”.

The button allows you to scroll backwards and forwards a day at a time.

^{Using the red dot}ꢐ ^{button you can load the selected programme into the recording settings (see item}

“Recording”).

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

CATEGORIES VIEW

The “Categories” view can be called up at any time in EPG by pressing the (blue) button.

In the “Categories” view you can see all programmes sorted by category and starting time.

The following categories are available for selection: Movies, Series, Sport, Children’s programmes,

Chat shows, News, Magazines/Reportage, Art/Culture, Science/Education, Music, Leisure and Adult

programmes.

Programmes can be assigned to the above categories only if the EPG data has been supplied by the

channel provider.

^{Select the required category using the}ꢍꢙ ^{buttons. You can then use the cursor buttons (}ꢕꢖꢔꢗ⁾

^{to select the desired category and if available you can use the}ꢒ ^{button within each category to call up}

further information on the desired programme.

The button allows you to scroll backwards and forwards a day at a time.

^{Using the red dot}ꢐ ^{button you can load the selected programme into the recording settings (see item}

“Recording”).

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

SCAN FUNCTION

^{The scan function can be called up at any time in EPG by pressing the}ꢑ ^button.

The scan function allows you to search for programmes based on their additional information or their

name. Use the keypad to input the desired search expression (see also “Operating instructions”

“Alphanumeric input”).

^{When you have input the desired search expression, press the}ꢓ ^{button to start the scan.}

^{You can then use the cursor buttons (}ꢕꢖꢔꢗ^{) to select the desired programme from the search result}

^{and if available you can use the}ꢒ ^{button to call up further information on the desired programme.}

^{Using the red dot}ꢐ ^{button you can load the selected programme into the recording settings (see item}

“Recording”).

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

ADDITIONAL INFORMATION (i-BUTTON)

The additional information can always be called up by

pressing the button whenever the “i symbol” appears

ꢒ

in front of the program name (see screenshot on the right).

First however the channel must be selected. The following

display appears (example):

The additional information available for a programme is displayed in its own window. By pressing the

ꢖ ^{button, if available, you can call up further additional information on the selected programme.}

The

buttons enable you to display the additional information for the preceding or following

ꢔꢗ

programmes in the order of the previously selected list (see header). This always assumes that the

data has been supplied by the channel provider.

^{Using the red dot}ꢐ ^{button you can load the selected programme into the recording settings (see item}

“Recording”).

^{Press the}ꢒ ^orꢌ ^{button to exit the additional information.}

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

RECORDING (TIMER)

^{The red dot}ꢐ ^{button allows you to set up a programme at any time for recording on an external recorder.}

^{The programme to be recorded can be selected in any of the EPG views, provided the red dot}ꢐ ^button

appears at the bottom of the screen display.

Programme present in the EPG:

^{Select the desired programme and press the red dot}ꢐ ^{button. The following display appears (example):}

Programme not present in the EPG:

Select any programme on the channel on which the desired programme is to be transmitted at a later

^{time and press the red dot}ꢐ ^{button (starting and ﬁnishing times together with the recording date must}

be input manually). The following display appears (example):

Remember to program

your external recorder

in accordance with the

scheduled recordings

registered

receiver.

the

^{Use the}ꢔꢗ ^{buttons to select the desired recording mode. The recording mode options available are:}

Once: The recording will be performed once

Daily: The recording will be performed daily at a time speciﬁed by you

Weekly: The recording will be performed once a week on the same day and at the same time

User-deﬁned: The recording will be performed on days speciﬁed by you at times speciﬁed by you

Series recording: The selected programme will be set up by the EPG for recording every time it is

transmitted (may even be on different channels). This function does however require a daily update

of the EPG data (the data are updated automatically when switching off into stand-by mode).

^{Use the cursor buttons (}ꢕꢖꢔꢗ^{) to select the further items and use the keypad to complete}

^{the settings. When all settings have been made, press the}ꢓ ^{button to save the recording settings.}

You can view the scheduled recordings in the recording schedule view of the EPG (see item

“Recording schedule”).

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

RECORD ONCE

Use the

(timer)”).

buttons to select the recording mode “once” (see screenshot item “Recording

ꢔꢗ

^{Use the}ꢕꢖ ^{buttons to switch to the selection ﬁeld “date” and use the}ꢔꢗ ^{buttons to select the}

desired recording date.

^{Use the}ꢕꢖ ^{buttons to switch to the selection ﬁeld “Start” and use the}ꢔꢗ ^{buttons to select the}

desired recording starting time.

^{Use the}ꢕꢖ^{buttons to switch to the selection ﬁeld “End” and use the}ꢔꢗ^{buttons to select the desired}

recording ﬁnishing time.

^{When all settings have been made, press the}ꢓ ^{button to save the recording settings. You can view}

the scheduled recording in the recording schedule view of the EPG (see item “Recording schedule”).

RECORD DAILY

^{Use the}ꢔꢗ ^{buttons to select the recording mode “daily” (see screenshot below).}

^{Use the}ꢕꢖ ^{buttons to switch to the selection ﬁeld “Start” and use the}ꢔꢗ ^{buttons to select the}

desired recording starting time.

^{Use the}ꢕꢖ^{buttons to switch to the selection ﬁeld “End” and use the}ꢔꢗ^{buttons to select the desired}

recording ﬁnishing time.

^{When all settings have been made, press the}ꢓ ^{button to save the recording settings. You can view}

the scheduled recording in the recording schedule view of the EPG (see item “Recording schedule”).

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

RECORD WEEKLY

Remember that the day of the week for the desired programme is loaded in

the recording schedule and you can make no further manual corrections to it!

^{Therefore before pressing the red dot}ꢐ ^{button, select the programme on the day}

of the week that in future you will wish to make the weekly recording.

^{Use the}ꢔꢗ ^{buttons to select the recording mode “weekly” (see screenshot below).}

^{Use the}ꢕꢖ ^{buttons to switch to the selection ﬁeld “Start” and use the}ꢔꢗ ^{buttons to select the}

desired recording starting time.

^{Use the}ꢕꢖ^{buttons to switch to the selection ﬁeld “End” and use the}ꢔꢗ^{buttons to select the desired}

recording ﬁnishing time.

^{When all settings have been made, press the}ꢓ ^{button to save the recording settings. You can view}

the scheduled recording in the recording schedule view of the EPG (see item “Recording schedule”).

RECORD USER-DEFINED

^{Use the}ꢔꢗ ^{buttons to select the recording mode “user-deﬁned” (see screenshot below).}

^{Use the}ꢕꢖ ^{buttons to switch to the selection ﬁeld “Day” and use the}ꢔꢗ ^{buttons to select the}

^{desired recording day. Press the}ꢓ ^{button to ﬁx the selection (the day will be shown in red letters). If}

necessary the receiver will suggest some days to you; you can accept these suggestions or deactivate

^{them again using the cursor buttons and pressing the}ꢓ ^{button once.}

^{Use the}ꢕꢖ ^{buttons to switch to the selection ﬁeld “Start” and use the}ꢔꢗ ^{buttons to select the}

desired recording starting time.

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

Use the

buttons to switch to the selection ﬁeld “End” and use the

buttons to select

ꢕꢖ

ꢔꢗ

the desired recording ﬁnishing time.

^{When all settings have been made, press the}ꢓ ^{button to save the recording settings. You can view}

the scheduled recording in the recording schedule view of the EPG (see item “Recording schedule”).

SERIES RECORDING

Series recording depends on the EPG data being kept up to date at all times. The

receiver automatically updates the EPG data when the unit is switched off by pressing

^theꢀ ^{button. Updating is important because it enables the receiver to recognise}

for purposes of recording any changes to scheduled transmission times of the

series, provided these were incorporated in the EPG data supplied by the channel

provider in advance of the latest EPG update.

^{Use the}ꢔꢗ ^{buttons to select the recording mode “Series recording”.}

In series recording the start and ﬁnish of recording are taken automatically by the receiver from

the EPG data. You can only specify a lead-in and run-out time to be sure to record the complete

programme even if transmission times may vary slightly. The setting of lead-in and run-out time

^{is done using the}ꢔꢗ ^{buttons or the keypad.}

^{When all settings have been made, press the}ꢓ ^{button to save the recording settings. You can view}

the scheduled recordings in the recording schedule view of the EPG (see item “Recording schedule”).

Download from Www.Somanuals.com. All Manuals Search And Download.

EPG - ELECTRONIC PROGRAMME GUIDE

VIEW RECORDING SCHEDULE

The “Recording schedule” view can be called up at any time in EPG by pressing the (red) button.

The recording schedule view shows you all the recordings that are scheduled.

^Theꢍꢙ ^{buttons allow the recordings to be sorted into “One-off” or “Repeating” recordings.}

^{The cursor buttons (}ꢕꢖꢔꢗ^{) allow you to select a recording. The}ꢓ ^{button allows you to switch}

over the channels on which the recording is scheduled.

^{The red dot}ꢐ ^{button allows you to delete a recording that had been scheduled. If this is a series}

recording you will additionally be asked whether you wish to cancel the recording of only one episode or

whether you wish to record no further episodes of this series (see screenshot). Selection is performed

^{using the}ꢕꢖ ^{buttons and is conﬁrmed using the}ꢓ ^button.

The button allows you to skip backwards and forwards through the future scheduled recordings, a day

at a time.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMMON INTERFACE

IMPORTANT INFORMATION

Always follow the operating instructions from your Pay-TV provider and the instructions

supplied with the Smartcard and the CA module!

Smartcards and CA modules are not included with this product!

The cards and modules are issued by the respective Pay TV providers, and contain the

subscriber data and details of the channels for which the subscriber has paid. These

channels are always encrypted.

Contact the Pay TV provider if you are interested in subscribing to a particular Pay TV

channel.

You are responsible for the use of the Smartcard in the CA!

The Smartcard sold by the Pay TV provider, speciﬁc to a particular encryption

technology, is inserted into the CA module.

Store your card and PIN code securely when not in use!

INSERTING THE SMARTCARD AND THE CA MODULE

ꢃ

^{The Common Interface (CI)}ꢃ ^{on the UFS 712 is suitable for the use of two CA (Conditional Access)}

modules. These two CI slots are on the front right behind the display.

^{The CA module}ꢂ ^{receives Smartcard}ꢁ ^{(chip contacts pointing upwards and towards socket strip) and}

^{is then inserted into one of the two CI slots}ꢃ^.

The Smartcard should be inserted into the CA module without exerting too much force. This also applies to

inserting the CA module into the CI slot.

Do not force the card in; and follow the instructions supplied with the Smartcard and the CA module.

To remove the module, press the relevant eject button

Download from Www.Somanuals.com. All Manuals Search And Download.

COMMON INTERFACE

You can ﬁnd out which Conditional Access modules are in the CI slots on the UFS 712 and which Smartcard

is in which CA module from the “Main menu” under „Settings“, and the “Common Interface” menu.

^{Conﬁrmation is by pressing the}ꢓ ^button.

^{Use the}ꢕꢖ ^{buttons to select one of the two slots in which the CA module is located (“Module inserted”)}

^{and then press the}ꢓ ^{button. You will then see the menu generated by the CA module.}

The screenshots below depend on the speciﬁc module and card, and so are only intended as

examples:

From this menu, your card and your PIN code allow you to access various channels from your Pay-TV

provider.

“CryptoWorks” has been selected as an example here. The details can be different for each CA module.

Always follow the instructions supplied by your Pay-TV provider!

Note:

The module displays may be shown in English, even if you have selected German as

the menu language, because the menu is generated directly by the module!

Information for Conax, SECA, Viaccess and CryptoWorks users:

Note that with monthly activation intervals, the channel providers have different procedures

for activating Pay TV cards. Activation may therefore be a few days before or after the

beginning of a new month. During this activation period, the CA module and card must

be in the slot, and the receiver must be turned on a set to the booked Pay TV channel.

Follow the instructions from the Pay TV provider.

If your Pay TV card is then still not enabled, we recommend you brieﬂy withdraw the CA

module with the card out of the slot, with the receiver switched on, and then re-insert it.

This information has nothing to do with the properties of the unit; it is merely intended to

assist you.

^{The various items can be selected using the}ꢕꢖ ^{buttons and called up using the}ꢓ ^{button. Press}

^theꢌ ^{button to exit the menu again.}

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEOTEXT (TELETEXT)

This symbol

in the channel notiﬁcation shows you whether Videotext/Teletext is available for the

selected channel.

^{When you press the}ꢑ ^{button, the receiver processes the videotext/Teletext service data for your TV set}

to display, even when the signal is encrypted.

During the scan, the page which is being searched for is displayed in the top left-hand corner with

the time and date displayed at the top right.

When the scan is ﬁnished, the videotext/Teletext being broadcast by the relevant encrypted provider

appears.

You have several options for calling up the desired pages:

Input with number pad

^{Page-by-page using the}ꢕꢖ ^buttons

Selection using the options indicated by the coloured buttons

(red),

(green),

(yellow) and

(blue)

By pressing the

button you can double the size of the displayed text. Pressing the

button

ꢓ

once enlarges the upper part of the display, pressing it twice enlarges the lower part of the display

^{(pressing the}ꢓ ^{button again returns the display to normal size).}

^{Press the}ꢌ ^orꢑ ^{button to exit videotext/Teletext.}

Download from Www.Somanuals.com. All Manuals Search And Download.

EDIT CHANNEL LIST

^{Select the “Edit channel list” menu using the menu button}ꢋ^{, the}ꢕꢖ ^{buttons on the main menu}

^andꢓ^.

Also pay attention to the bars

at the bottom of the on-screen

display! This provides hints on

what to do next.

^{Press the}ꢓ ^{button to close the information display for editing channels and channel lists. When the}

menu is called up, the standard setting is for the receiver to show the “All Satellites” channel list with all

channels available on the satellites that are being received.

SELECTION OF THE LIST/CHANNELS TO BE EDITED

Press the (blue) button to switch between the TV and radio channel lists. Radio channels are edited in

the same way as TV channels.

Editing favourites lists is explained as a separate item.

Selection options:

Switch between radio and TV channels

(blue) button

(green) button

(yellow) button

Call up satellite channel lists

Call up the channel lists, sorted alphabetically

Search for a particular channel (input the search expression using the

numeric pad on the remote control, see also the section “Operating

instructions” “Alphanumeric input”)

ꢑ ^button

The channel list chosen is generally that sorted by categories (satellites, favourites and alphabetic) using

^theꢍꢙ ^{buttons (the standard list shown on calling up is the “All Satellites” channel list). Selection of}

^{channels in the list is performed using the cursor buttons (}ꢕꢖꢔꢗ^{). The}ꢕꢖ ^{buttons allow you to}

^{select individual channels, and the}ꢔꢗ ^{buttons allow you to scroll from page to page of the currently}

selected list.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDIT CHANNEL LIST

EDITING LISTS/CHANNELS

^{When you have selected the channel or channel list to be edited, press the red dot}ꢐ ^{button to call up}

the edit menu. You have the following edit options:

Move:

Channel can be moved within the current list to another channel slot

Delete:

Delete the channel from the current list

Skip:

Channel will be skipped when zapping through the channels

Lock:

Channel can be viewed only by inputting a PIN

Add to favourites list:

Channel can be assigned to any favourites list

Start block highlighting:

Several channels can be highlighted at the same time and edited together

As soon as you exit the menu under which you made the edit changes, you will

be asked if you wish to save the changes. Use the

buttons to select either

ꢕꢖ

^{“Yes, save changes” or “No, discard changes”. Conﬁrm your selection with the}ꢓ ^button.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDIT CHANNEL LIST

“LAST FUNCTION” MEMORY

^{The last editing action performed is saved on the}ꢚ ^{button, so by pressing the}ꢚ ^{button for other}

channels you will repeat the action without having to all up the edit menu again. As soon as you leave

the current display, this option lapses and becomes available again only after the edit menu has been

called up and an action selected.

MOVE CHANNELS

(green)

^{Use the}ꢕꢖ ^{buttons to select the channel to be moved from the current channel list (use the}

button to switch to the overall list, use the

(yellow) button to switch to the alphabetically sorted list).

^{Press the}ꢐ ^{button to call up the edit menu and use the}ꢕꢖ ^{buttons to select the “Move” function.}

^{Conﬁrm the command by pressing the}ꢓ ^button.

The channel you previously selected will now be shown inset slightly from the left. Now use the cursor

^{buttons (}ꢕꢖꢔꢗ^{) or the keypad to select the new desired position for the channel, and conﬁrm}

^{the new channel slot by pressing the}ꢓ ^button.

DELETE CHANNELS

^{Use the}ꢕꢖ ^{buttons to select the channel to be deleted from the current channel list. Press the}

ꢐ ^{button to call up the edit menu and use the}ꢕꢖ ^{buttons to select the “Delete” function. Conﬁrm}

^{the command by pressing the}ꢓ ^button.

A deleted channel can be rediscovered only by performed another channel scan

(see section “Channel scan”)!

The channel you previously selected will be deleted (from the favourites lists also!).

SKIP CHANNELS

^{Use the}ꢕꢖ ^{buttons to select the channel to be skipped from the current channel list. Press the}

ꢐ ^{button to call up the edit menu and use the}ꢕꢖ ^{buttons to select the “Skip” function. Conﬁrm}

^{the command by pressing the}ꢓ ^button.

The channel you previously selected is now shown in grey text. When zapping the channels this

^{channel will in future be skipped and no longer shown in the channel list (called up using the}ꢓ ^button).

This function can be restored again using the edit menu (select: “Unskip”).

Download from Www.Somanuals.com. All Manuals Search And Download.

EDIT CHANNEL LIST

LOCK CHANNELS

^{Use the}ꢕꢖ ^{buttons to select the channel to be blocked from the current channel list. Press the}

ꢐ ^{button to call up the edit menu and use the}ꢕꢖ ^{buttons to select the “Lock” function. Conﬁrm}

^{the command by pressing the}ꢓ ^{button; you are now prompted to enter the PIN code (factory default}

setting: 0000).

The channel you previously selected is now shown with a padlock to its right. In future this channel can

be viewed only by inputting the four-digit PIN code.

This function can be restored again using the edit menu (select: “Unlock”).

COPY CHANNELS TO THE FAVOURITES LIST

Use the

buttons to select the channel to be copied from the current channel list. Press the

ꢕꢖ

ꢐ ^{button to call up the edit menu and use the}ꢕꢖ ^{buttons to select the “Add to favourites list” function.}

^{Use the}ꢔꢗ ^{buttons to select the favourites list into which the channel is to be copied. The channel}

^{remains in the satellite channels list. Conﬁrm the command by pressing the}ꢓ ^button.

The channel you previously selected is now shown with an “F” and a yellow ﬁeld in the channels list.

The “F” shows that it is a favourite channel; the black dot in the yellow ﬁeld shows in which of the

eight favourites lists the channel can be found.

See the item “Editing favourites lists” for information on how to delete a channel from a favourites list.

START BLOCK HIGHLIGHTING (HIGHLIGHTING SEVEREAL CHANNELS)

^{Use the}ꢕꢖ ^{buttons to select the channel from which you want to highlight further channels. You can}

^{only select channels that are listed in succession in your selected channel list. Press the}ꢐ ^button

^{to call up the edit menu and use the}ꢕꢖ ^{buttons to select the “Block highlighting” function. Use the}

ꢕꢖ ^{buttons to highlight the desired channels, starting from the previously highlighted channel and}

working upwards or downwards. The highlighted channels will be highlighted in yellow and marked with

a tick at the left side.

^{When you have highlighted the channels that you wish to select, press the}ꢐ ^{button to call up the edit}

^{menu once again and use the}ꢕꢖ ^{buttons to select the desired function (“Move”, “Delete”, “Skip”, “Lock”}

or “Add to favourites list”).

The selected function can now be used in the same way as described for the respective items in this section

for a single channel.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDIT CHANNEL LIST

EDIT FAVOURITES LISTS

When you have selected the favourite list to be edited (called up using the

(red) button

and selected using the

You have the following edit options:

buttons), press the red dot

button to call up the edit menu.

ꢍꢙ

ꢐ

Remove from the Favourites List:

The channel will be removed from the Favourites List

Lock:

Channel can be viewed only by inputting a PIN

Rename Favourites List:

The Favourites List can be renamed

Start block highlighting:

Several channels can be highlighted at the same time and edited together

REMOVE FROM THE FAVOURITES LIST

^{Use the}ꢕꢖ ^{buttons to select the channel to be removed from the Favourites List you have selected.}

^{Press the}ꢐ ^{button to call up the edit menu and use the}ꢕꢖ ^{buttons to select the “Remove from}

^{Favourites List” function. Conﬁrm the command by pressing the}ꢓ ^button.

The channel you previously selected is now removed from the Favourites List (but not deleted from the

overall satellite list).

Download from Www.Somanuals.com. All Manuals Search And Download.

EDIT CHANNEL LIST

LOCK CHANNELS

^{Use the}ꢕꢖ ^{buttons to select the channel to be blocked in the Favourites List you have selected.}

^{Press the}ꢐ ^{button to call up the edit menu and use the}ꢕꢖ ^{buttons to select the “Lock” function.}

^{Conﬁrm the command by pressing the}ꢓ ^{button; you are now prompted to enter the PIN code (factory}

default setting: 0000).

The channel you previously selected is now shown with a padlock to its right. In future this channel can

be viewed only by inputting the four-digit PIN code.

The channel is also blocked on all other channel lists. You need not additionally block the channel in

the other channel lists.

This function can be restored again using the edit menu (select: “Unlock”).

RENAME FAVOURITE LIST

Use the

buttons to select the Favourites List to be renamed. Press the

button to call

ꢍꢙ

ꢐ

^{up the edit menu and use the}ꢕꢖ ^{buttons to select the “Rename Favourites List” function. Conﬁrm}

^{the command by pressing the}ꢓ ^{button. A keypad will now be displayed with which you can enter}

the desired name alphanumerically using the numeric pad on the remote control. See also the section

“Operating instructions”, “Alphanumeric input”).

START BLOCK HIGHLIGHTING (HIGHLIGHTING SEVEREAL CHANNELS)

^{Use the}ꢕꢖ ^{buttons to select the channel from which you want to highlight further channels. You can}

^{only select channels that are listed in succession in your selected Favourites List. Press the}ꢐ ^button

^{to call up the edit menu and use the}ꢕꢖ ^{buttons to select the “Block highlighting” function. Now use}

^theꢕꢖ ^{buttons to highlight the desired channels, starting from the previously highlighted channel}

and working upwards or downwards. The highlighted channels will be highlighted in yellow and marked

with a tick at the left side.

^{When you have highlighted the channels that you wish to select, press the}ꢐ ^{button to call up the}

^{edit menu once again and use the}ꢕꢖ ^{buttons to select the desired function (“Remove from the}

Favourites List”, or “Unlock”).

The selected function can now be used in the same way as described for the respective items in this

section for a single channel.

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANNEL SEARCH (CHANNEL SCAN)

^{Select the „Channel scan“ menu using the menu button}ꢋ^{, the}ꢕꢖ ^{buttons on the main menu and}ꢓ^.

Also pay attention to the bars at the

bottom of the on-screen display! This

provides hints on what to do next.

You have three options for a channel scan:

Automatic scan - all transponders for the satellite you selected will be scanned

Manual scan - only the selected transponder for the satellite you selected will be scanned

Channel scan with service ID -

Search for a speciﬁc channel using its service ID

^{Select the scan type you want to rename using the}ꢕꢖ ^{buttons and conﬁrm with}ꢓ^.

AUTOMATIC (CHANNEL) SCAN

^Theꢕꢖ ^{buttons allow you to select different sets of parameters for the scan.}

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANNEL SEARCH (CHANNEL SCAN)

Satellite

^{Select the satellite to be scanned, using the}ꢔꢗ ^{buttons. Make sure your reception system is aligned}

to the selected satellite. You can scan only one satellite at a time. If you have connected a multi-feed

reception system (e.g. reception of ASTRA 19.2° East and HOTBIRD 13° East), you must repeat this

procedure once for each satellite. You can however start the ﬁrst installation again, in the course of which

a channel scan of all the satellites you selected is performed.

^{Press the}ꢖ ^{button to move to the next selection item.}

Channel scan mode

Use the

or “only encrypted” channels.

buttons to select whether you wish to scan “only free and encrypted”, “only free”

ꢔꢗ

To view encrypted channels you need the appropriate CA (Conditional Access) module and a

valid smart card together with a valid subscription to the respective Pay-TV provider.

^{Press the}ꢖ ^{button to move to the next selection item.}

Network scan

^{Use the}ꢔꢗ ^{buttons (On/Off) to select whether a network scan should be performed. If you set the}

network scan to “Off”, only the factory stored transponders of the satellites you previously selected will

be scanned for new as yet unlisted channels.

If you set the network scan to “On”, the transponder network enables additional transponders that have

not yet been stored to be located. They are then stored and scanned for new channels in the same way

as the existing transponders.

^{When you have made your settings, use the}ꢕꢖ ^{buttons to select “Start Scan” and press the}ꢓ ^button

^{to start scanning. You can break off the scan prematurely at any time by pressing the}ꢌ ^{button. During}

the scan you will see the following message (example):

Radio channels

found

TV channels found

Satellite with

the transponder

currently being

scanned

Progression bar

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANNEL SEARCH (CHANNEL SCAN)

Newly found channels are identiﬁed with the designation “New” after the channel name. After completion

of the scan, you will see the following message (example):

^{Press the}ꢓ ^{button. You will be asked whether you wish to save the changes or not. Selection is}

^{performed using the}ꢕꢖ ^{buttons and is conﬁrmed using the}ꢓ ^{button. If you select “Yes, save}

^{changes”, the newly found channels will be added to the end of the channel list. Then press the}ꢌ

^{button to exit the menu. The channel list is called up on to the TV screen by pressing the}ꢓ ^button

(see also section “On-screen displays” “Channel list TV/Radio”).

After a scan (of whatever type) the receiver shows all newly found channels in

the channel list under the rubric “New Channels”. You will ﬁnd this rubric in

the Channel List at the end of the green satellite channel lists (selection using

^theꢍꢙ ^buttons).

MANUAL (CHANNEL) SCAN

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANNEL SEARCH (CHANNEL SCAN)

^Theꢕꢖ ^{buttons allow you to select different sets of parameters for the scan.}

Satellite

^{Use the}ꢔꢗ ^{buttons to select the satellite on which the transponder you wish to scan is located.}

Make sure your reception system is aligned to the selected satellite. You can scan only one transponder

at a time. If you wish to scan several transponders on a satellite, you should start an automatic scan

of the transmitting satellite.

^{Press the}ꢖ ^{button to move to the next selection item.}

Transponder frequency

Select the transponder to be scanned, using the

of the screen display, the receiver shows the current signal strength and signal quality of the selected

buttons or the keypad. At the bottom right

ꢔꢗ

^{transponder. Press the}ꢖ ^{button to move to the next selection item.}

Channel scan mode

^{Use the}ꢔꢗ ^{buttons to select whether you wish to scan “only free and encrypted”, “only free” or}

“only encrypted” channels.

To view encrypted channels you need the appropriate CA (Conditional Access) module and a

valid smart card together with a valid subscription to the respective Pay-TV provider.

^{Press the}ꢖ ^{button to move to the next selection item.}

Network scan

^{Use the}ꢔꢗ ^{buttons (On/Off) to select whether a network scan should be performed. If you set the}

network scan to “Off”, only the factory stored transponders of the satellites you previously selected will be

scanned for new as yet unlisted channels.

If you set the network scan to “On”, the transponder network enables additional transponders that have

not yet been stored to be located. They are then stored and scanned for new channels in the same way as

the existing transponders.

^{When you have made your settings, use the}ꢕꢖ ^{buttons to select “Start Scan” and press the}ꢓ ^button

^{to start scanning. You can break off the scan prematurely at any time by pressing the}ꢌ ^button.

During the scan you will see a display that shows you the progress of the scan and the channels

found so far. Newly found channels are identiﬁed with the designation “New” after the channel name.

After completion of the scan, you will see the following message (example):

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANNEL SEARCH (CHANNEL SCAN)

^{Press the}ꢓ^{button. You will be asked whether you wish to save the changes or not. Selection is performed}

^{using the}ꢕꢖ ^{buttons and is conﬁrmed using the}ꢓ ^{button. If you select “Yes, save changes”, the}

^{newly found channels will be added to the end of the channel list. Then press the}ꢌ ^{button to exit the}

^{menu. The channel list is called up on to the TV screen by pressing the}ꢓ ^{button (see also section}

“On-screen displays” “Channel list TV/Radio”).

CHANNEL SCAN WITH SERVICE ID

^Theꢕꢖ ^{buttons allow you to select different sets of parameters for the scan.}

Satellite

^{Use the}ꢔꢗ ^{buttons to select the satellite that is transmitting the channels to be scanned. Make sure}

your reception system is aligned to the selected satellite.

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANNEL SEARCH (CHANNEL SCAN)

^{Press the}ꢖ ^{button to move to the next selection item.}

Transponder frequency

^{Use the}ꢔꢗ ^{buttons or the keypad to select the transponder frequency on which the channel being}

sought is transmitted. At the bottom right of the screen display, the receiver shows the current signal

strength and signal quality of the selected transponder.

^{Press the}ꢖ ^{button to move to the next selection item.}

Service ID

^{Using the}ꢔꢗ ^{buttons or the keypad, enter here the service ID of the channel being sought.}

^{When you have made your settings, use the}ꢕꢖ ^{buttons to select “Start Scan” and press the}ꢓ ^button

^{to start scanning. You can break off the scan prematurely at any time by pressing the}ꢌ ^button.

During the scan you will see a display that shows you the progress of the scan.

After completion of the scan, you will see the following message (example):

^{Press the}ꢓ ^{button. You will be asked whether you wish to save the changes or not. Selection is}

^{performed using the}ꢕꢖ^{buttons and is conﬁrmed using the}ꢓ^{button. If you select “Yes, save changes”,}

^{the newly found channels will be added to the end of the channel list. Then press the}ꢌ ^{button to exit}

^{the menu. The channel list is called up on to the TV screen by pressing the}ꢓ ^{button (see also section}

“On-screen displays” “Channel list TV/Radio”).

Download from Www.Somanuals.com. All Manuals Search And Download.

PARENTAL CONTROL

^{Select the “Parental control” menu using the menu button}ꢋ^{, the}ꢕꢖ ^{buttons on the main menu}

^andꢓ^{. You are now prompted to enter the PIN code (factory default setting: 0000). After entering the}

PIN using the keypad you are shown the following display:

Also pay attention to the bars

at the bottom of the on-screen

display! This provides hints on

what to do next.

^{Select the parameters to be changed using the}ꢕꢖ ^buttons.

BLOCKING THE MAIN MENU

^{Use the}ꢔꢗ ^{buttons (On/Off) to select whether the main menu should be blocked. If the menu is}

blocked, changes can be made only by entering the four-digit PIN code.

BLOCKING THE RECEIVER

^{Use the}ꢔꢗ ^{buttons (On/Off) to select whether the receiver should be blocked. If the receiver is}

blocked, it can be operated only by entering the four-digit PIN code after it is switched on (factory

setting: 0000).

^{Press the}ꢌ ^{button to exit the menu again.}

Download from Www.Somanuals.com. All Manuals Search And Download.

PARENTAL CONTROL

SETTING A NEW CODE (PIN)

^Pressꢓ ^{to replace the old PIN with a new one. Enter the new (four-digit) PIN. For security you must}

repeat the new PIN code once again.

^{Conﬁrm the change of PIN code by pressing the}ꢓ ^button.

Keep your password in a safe place, so that you always have access to your channels

even if you might have forgotten it.

If you have forgotten your password, you must contact your dealer, who will be able

to unlock your receiver for you.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS

The selected menus, sub-menus and positions, as well as the parameters to be set, are each highlighted

in colour. The menus are self-explanatory to a great extent.

Pay attention to the bar at the

bottom of the on-screen display!

This provides hints on what to do

next.

^{Select the “Settings” menu using the menu button}ꢋ^{, the}ꢕꢖ ^{buttons on the main menu and}ꢓ^.

^Pressꢓ ^{to access the “TV, Video and Audio” menu. The following display appears (see next page):}

^{Use the}ꢕꢖ ^{buttons to select the further options. If there is another sub-menu layer, press the}

ꢓ

^{button to open it. If there are no more sub-menus, make the settings using the}ꢔꢗꢕꢖ ^{or number}

pad.

^{Press the}ꢌ ^{button to save your settings and return to the previous menu. Press the}ꢋ ^{button to}

return directly to the TV picture, the changes will also be saved.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS

TV SETTINGS

TV TYPE

^{Here you can use the}ꢔꢗ ^{buttons to select the picture format for your TV. Either}

4:3 or

16:9 format.

DISPLAY FORMAT

^{Use the}ꢔꢗ ^{buttons here to select the type of screen display:}

•

Pan & Scan

Letterbox

Automatic (only if the “16:9” TV format was selected)

Always 16:9 (only if the “16:9” TV format was selected)

TV SCART SIGNAL OUTPUT

^{Here you can use the}ꢔꢗ ^{buttons to select the type of video signal at the TV Scart socket. Select}

the signal that your TV set can process. When doing this, refer to the operating instructions for

your TV set!

•

FBAS – Composite baseband signal

(colour/picture/blanking/synchronous signal)

RGB – Red/Green/Blue signal or

Y/C – S-Video signal (luminance/chrominance)

•

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS

VCR SCART SIGNAL OUTPUT

^{Here you can use the}ꢔꢗ ^{buttons to select the type of video signal at the VCR Scart socket. Select}

the signal that your external recorder can process. When doing this, refer to the operating instructions for

your recorder!

•

FBAS – Composite baseband signal

(colour/picture/blanking/synchronous signal)

Y/C – S-Video signal (luminance/chrominance)

TELEVISION SYSTEM

^{Here, you can use the}ꢔꢗ ^{buttons to specify whether your TV set is a}

•

PAL or

NTSC set.

AUTOM. DOLBY DIGITAL OUTPUT

^{Here you can use the}ꢔꢗ ^{buttons to select whether the receiver should automatically output the}

Dolby Digital signal (if this is transmitted).

AUDIO DELAY

^{Here you can use the}ꢔꢗ ^{buttons to set a delay in milliseconds, if the sound output from your}

receiver is out of synch with the TV picture (lip synchronicity). The delay can be set in 10 millisecond

steps from 10 ms up to 200 ms.

CONFIGURING THE ON-SCREEN MENU

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS

FUNCTIONAL SCOPE

Here you can conﬁgure the functional scope of your receiver. You can choose between “High”, “Normal”

and “Low”. The following table shows which functions are available at each conﬁguration step.

(red) button

(yellow) button

(blue) button

TV/Radio

button

ꢈ

ꢓ

High

Low

Select favourites

Select options

Not assigned

Select options

AV changeover

Channel list

Not assigned

TV/Radio

Not assigned Programme Guide

Normal Select favourites

DISPLAY DURATION OF CHANNEL MESSAGE

^{Use the}ꢔꢗ ^{buttons to select the time after which you want the on-screen channel message display}

to be automatically cancelled. The selections available are “Off”, 1, 2, 3, 4, 5 or 6 seconds.

DISPLAY VOLUME BAR

^{Use the}ꢔꢗ ^{buttons (On/Off) to specify whether the volume bar is displayed when adjusting the}

volume.

RECEIVER FRONT DISPLAY BRIGHTNESS

^{Use the}ꢔꢗ ^{buttons to set the brightness of the receiver front display. Select the most comfortable}

setting for the ambient lighting.

RECEIVER FRONT DISPLAY IN STANDBY

Use the

stand-by mode (display of time).

buttons to set whether the receiver front display should be switched on or off in

ꢔꢗ

OSD POSITION ALIGNMENT

Press the

screen displays on the TV screen.

Now you can use the cursor buttons

button to align the on-

ꢓ

⁽ꢔꢗꢕꢖ^{) to determine the position}

of the on-screen display. When you have

achieved the desired position, press the

ꢓ ^{button to ﬁx the selected position.}

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS

DATE AND TIME

Set Local Time

Use the

Germany +1 hour).

buttons to set the time zone variation from UTC (formerly GMT) (e.g. for

ꢔꢗ

^{Use the}ꢕꢖ ^{buttons to switch to the “Automatic Time Setting” ﬁeld.}

Automatic time setting

^{Use the}ꢔꢗ ^{buttons to select whether the receiver should automatically change over to and from}

summer and winter time. If “On” is selected, the receiver automatically sets itself to the right time.

If “Off” is selected, the ﬁeld for manual selection of summer and winter time is displayed below.

^{Use the}ꢔꢗ ^{buttons to perform the setting.}

^{Press the}ꢌ ^{button to exit the menu again.}

COMMON INTERFACE

See “Common Interface” section

ANTENNA CONFIGURATION

See “First Installation” section, pages 15ff

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE MENU

^{Select the “Service” menu using the menu button}ꢋ^{, the}ꢕꢖ ^{buttons on the main menu and}ꢓ^.

The following display appears:

Current SW Version

Hardware version

Channel list status

Last update run

UPDATE SOFTWARE

As soon as the receiver is switched to stand-by, not only are the current SI data

for the channels for the EPG updated, but the receiver also checks whether new

software is available. If new software is ready for downloading to your receiver,

you will see the appropriate message when next you switch on.

You can also check manually whether new software is available.

^{Use the}ꢕꢖ ^{buttons to switch to “Update software” and to call it up press the}ꢓ ^{button. The following}

display appears:

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE MENU

Also pay attention to the bars

at the bottom of the on-screen

display! This provides hints on

what to do next.

UPDATE Software

^{Use the}ꢔꢗ ^{buttons (No/Yes) to select whether you wish to load the new software that is available.}

If you are unsure whether you wish to load the new software, you can initially set the reply to “No”.

If you do agree to the changes, you can then proceed to download the software.

Update the Channel List

Use the

buttons (No/Yes) to select whether you wish to update the channel list by loading

ꢔꢗ

the updated channel data or not. In the new channel list, changes to channel transmission slots are

recognised and new channels are added.

When you have made your settings, use the

buttons to select “Start Update” and press the

ꢕꢖ

ꢓ ^{button to start updating.}

The following display appears (see example on next page):

If you load a new channel list, your old channel list together with your personal

settings (such as sorting) will be overwritten. If you do not wish your settings to

be lost, you can also perform a manual scan of the satellites that you receive, as

described in the “Channel scan” section. This will detect all new channels and all

changes to channels.

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE MENU

FACTORY DEFAULT

^{You can select the “Service” menu using the}ꢋ ^{menu button, the}ꢕꢖ ^{buttons in the main menu}

^andꢓ^{. Use the}ꢕꢖ ^{buttons to switch to “Load factory default settings” and to call them up, press}

^theꢓ ^{button. The following display appears:}

Press the

unchanged.

button to load the factory default settings. The channels and favourites lists remain

ꢓ

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING UP THE VIDEO/PVR

For details of how to connect your external recorder to the receiver refer to the connection diagram

provided at the end of this manual and the instructions for the external recorder.

RECORDING

In order to make a VCR recording (Record), the satellite receiver must be switched on or the timers

must be pre-programmed (see “EPG” “Recording (timer)” section).

PLAYBACK

For VCR/PVR playback you must have previously set the UFS 712 Scart socket to “VCR mode” (Scart

^{changeover), using the}ꢈ ^{button, so that the signal path is set up from the VCR or PVR/AUX Scart socket}

to the TV Scart socket.

In this setting, the picture from the external recorder is switched through to the TV set during playback.

Pressing the

button again restores priority to the UFS 712 “Scart → Sat” signal. In the setting

ꢈ

“Scart → TV” (TV mode) the internal tuner of the TV set has priority and you cannot then see the signal

from the receiver on the screen if you switch the TV set to the AV channel.

The settings “VCR mode” and “TV mode” are shown in the display on the receiver.

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE FRONT PANEL

If you have misplaced your remote control, or if the batteries are empty, you can still operate your

receiver from the front panel.

BACKUP OPERATION

There are three buttons on the front of the receiver.

TV/R button:

Pressing the TV/R button switches the receiver from TV mode to radio mode. Pressing the TV/R button

a second time switches the receiver from radio mode back into TV mode.

▼ button:

The channel down button switches to the next channel down in the currently selected channel list.

▲ button:

The channel up button switches to the next channel up in the currently selected channel list.

Because there are no number buttons, no password/PIN-protected functions can

be displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL APPENDIX

TECHNICAL FEATURES

Reception of digital TV and Radio satellite programmes

4,000 channel memory positions

16-digit alphanumerical display shows programme names, radio data and transmitter information

)

Common interface for two CA modules ¹

)

Kathrein Convenience EPG ²

Suitable for downloading software via satellite and PC (available only in the next software version)

8 favourite channel lists for TV and 8 for radio

Automatic date and time generation via DVB data stream

On-screen display (OSD) in 8 languages (D, GB, F, I, E, CZ, NL, TR)

Timer; can also be programmed using the EPG (any number of timers can be programmed)

Language selection for multilingual broadcasts

Optical and electrical audio output for Dolby Digital data stream (AC 3)

Composite colour, Y/C and RGB signal output programmable via the Scart socket

Cinch sockets for AV signal

Videotext decoder with 800-page memory and videotext generation

Automatic 4:3 and 16:9 format recognition (choice of viewing format)

VPS signal evaluation via VCR Scart socket with control of switch-off time

Channel scan

Programme position sort function

DiSEqC™1.1, SCR single-cable system andUFO^®micro control signals (available only in a later

software version)

Infra-red remote control

Power switch

An additional IR sensor can be connected

¹⁾CA modules and Smartcards are not included with this product

²⁾Only displayed if this information is broadcast by the programme provider

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL APPENDIX

Type

UFS 712si

UFS 712sw

Order no./colour

RF properties

20210085/silver

20210086/black

Input frequency range

Input level range

Reception threshold (EB/NO)

TV system, Video

Modulation, FEC, demultiplexer

Video resolution

Input data rate

MHz

dBµV

950-2150

44-83

< 4.5

DVB-S standard

CCIR 601 (720 x 576 lines)

Msymbols/s

2-45

Video decoding

Bit rate

MPEG-1 and 2 compatible

Mbit/s

MHz

V_ss

1.5-15

0.02-5

Frequency range

Output voltage

S/N

> 53

TV system, Audio

Audio decoding

sampling rate

MPEG-1 and 2, layer 1 and 2

kHz

mV_ss

32/44.1/48

0.04-20

Type 770

> 65

Frequency range

Output voltage

S/N

Memory

Flash-RAM/SDRAM

Processor clock speed

Power supply

4/32

221

MHz

Mains voltage

VAC/Hz

230 ± 15 %/50

Power consumption (power/standby)

LNB supply vert./horiz.

Control signal

< 26/< 2.5

14/18/Max. 350

V/mA

kHz

22; DiSEqC^TM1.1; UFO^®micro/DiSEqC^TM; SCR single cable system

Connections

Sat IF input/output

TV/VCR output

2 x F socket

2 x Scart sockets

Cinch socket

2 x Cinch sockets

Cinch socket

Standard ﬁbre-optic

RJ 11 socket

Video output

Audio output (analogue)

Audio digital output (electrical)

Audio digital output (optical)

Data interface

Common Interface

General

Permissible Ambient temperature

Unit dimensions

Weight

°C

+5 to +40

280 x 49 x 190

< 2

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL APPENDIX

SCART SOCKET ASSIGNMENT

Signal

Pin no.

VCR/AUX

Right audio output

Right audio input

Left audio output

Audio earth

Blue earth

Audio left input

Blue signal

Switching voltage

Green earth

Data signal

Green signal

Data signal

Red earth

Data earth

Red signal (C)

Blanking signal

Video earth

Blanking signal earth

Video output (FBAS/Y)

Video input

Connector shield

VHS/S-VHS SWITCHING

The Scart sockets are switchable between VHS and S-VHS. The switch is made by selecting “Main

menu”, “Settings”, “TV picture and sound”.

VHS (RGB):

The red signal is connected to terminal 15, the composite colour output to terminal 19.

For S-VHS (C/Y): The Y output is connected to pin 19, the C output to pin 15.

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL APPENDIX

CONNECTION EXAMPLE

Dolby digital system

Digital audio AV 2

Digitalton AC 3

(electrical/optical)

optisch/elektrisch

Scart

LLWWLL

Scart

Infrarot-Empfänger

Infra-red receiver

(optional)

Hi-ﬁ system

Download from Www.Somanuals.com. All Manuals Search And Download.

SHORT TECHNICAL GUIDE

CHANNEL PACKAGE

The channel package for a digital transponder normally includes several TV and radio channels. Each

channel package has a ﬁxed assignment for the transponder transmission frequency, for polarisation

(horizontal or vertical), for the symbol rate and for the Viterbi rate or error rate.

DISEQC™

DiSEqC™ (Digital Satellite Equipment Control) is a communication system between a satellite receiver

(master) and the peripheral satellite components (slaves), such as LNBs, multi-switches, rotating antenna

systems.

It is a single master/multi-slave system, i.e. there is only ever one master in the satellite system. All activities

start from the master.

DISEQC™ COMPONENTS

If DiSEqC™ switching matrices are cascaded, the master receiver must transmit the DiSEqC™ signal

several times, so that all DiSEqC™ multi-switches in the cascade receive their commands.

These days, DiSEqC™ components (slaves) must be reverse compatible, i.e. respond to the analogue

switching criteria from receivers that are only equipped with H/V and 22 kHz control signals.

A DiSEqC™ switching matrix will work with analogue switching criteria until the DiSEqC™ command

from the master is received. All analogue switching criteria are then ignored.

DVB MPEG-2

DVB is the abbreviation for Digital Video Broadcasting. DVB-S refers to the transmission method

(S = satellite). MPEG is the abbreviation for Moving Picture Experts Group, a working group that

formulates internationally applicable standards for the digital compression of video and audio. MPEG-2

has established itself as the standard for compression of digital TV signals. MPEG-2 works up to a data

rate of 100 Mbit/s.

EB/NO RATIO

The Eb/No ratio is a measure of the signal to noise ratio of a digital signal. The value is not identical to

the C/N value familiar from analogue reception technology. At Eb/No values below 5 dB no reception is

normally possible.

FEC

FEC is the abbreviation for Forward Error Correction. The FEC error rate corresponds to the Viterbi rate.

Download from Www.Somanuals.com. All Manuals Search And Download.

SHORT TECHNICAL GUIDE

PID

The PID (Packet IDentiﬁcation) number is an identiﬁcation number for video signals and audio signals in

the digital data stream of DVB-MPEG-2 signals. The receiver uses the PID number to create a unique

assignment for the video and audio data transmission. The PCR PID is the identiﬁcation number

for the synchronisation signal. The PCR PID is normally identical to the video PID. For programmes

broadcast in multiple languages, the audio PD can be entered manually to assign a different

language to the TV programme. After the PID is entered, the digital receiver automatically selects the

audio data identiﬁed by the PID number from the data stream and assigns it to the video signal.

SYMBOL RATE

The symbol rate describes the quantity of data that is transmitted per second. The symbol rate is

measured in MSymbols/s and is equal to the number of symbols received per second.

TRANSPONDER

A transponder is a satellite channel which transmits TV and radio signals. A satellite has several

transponders.

Analogue transponders transmit only one TV channel and possibly multiple radio channels on the

transmission frequency.

Digital transponders simultaneously transmit several TV and several radio programmes at

transmission frequency. If a channel provider is broadcasting several TV channels via a digital

transponder, we refer to this as the provider‘s channel package. The terms “digital transponder” and

“channel package” have the same meaning.

VIDEO-BIT-RATE

The video bit rate describes the quantity of data from the digitised video signal that is transmitted

per second.

VITERBI RATE

The Viterbi rate (code rate, error rate) characterises the error protection used by the programme provider.

The DVB standard provides the following values: 1/2 - 2/3 - 3/4 - 5/6 - 7/8

Download from Www.Somanuals.com. All Manuals Search And Download.

SHORT TECHNICAL GUIDE

GLOSSARY

AC 3

Output for Dolby Digital signal

Sound output on the receiver

Audio output

AV programme pos. Preferred programme position on TV set for Scart input

Conditional Access (for decoding of encrypted programmes)

Internationally standardised interface for CA modules

Decoder for Pay TV

Decoder

DiSEqC™

DVB

Control system between receiver and LNB, multi-switch

Digital Video Broadcasting

Eb/No [dB]

Eb/No ratio

LED display

LNB

Power density per unit of information

Digital signal to noise ratio

Display on receiver

Low Noise Block Converter

Mute

Muting of sound

OSD

On Screen Display

PAL

Analogue TV standard

Pay TV

PCMCIA

PID

Television channels available on subscription (e.g. PREMIERE)

Standard for internal decoder interface for pay TV

See “Short technical guide”

Personal Identiﬁcation Number

Receiver

RGB

Satellite receiver

Video signal made up of three individual colour signals (red, green, blue)

Receiver input signal

Satellite IF signal

Scart cable

Smartcard

Stand-by

S-VHS

21-pin connecting cable (e.g. receiver/TV)

Card from Pay TV provider to decode its channels

Standby mode

Super Video Home System (video recorder standard)

Rate of data transmission of satellite signal

Symbol rate

Time-shift function Time-shifted playback

Timer function

Transponder

Clock function for pre-programmed switch on and off times

See “Short technical guide”

UFO micro and

Kathrein-speciﬁc satellite signal processing systems

UFO mini

VCR connection

Viterbi rate

Video recorder connection

See “Short technical guide”

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

In the event of a malfunction, ﬁrst check all the cable connections and operating states:

1. Receiver and TV set power plugs are connected to wall socket

2. Antenna cables on receiver input

3. Receiver and TV set correctly connected by a Scart or cinch cable

4. Audio connections are made to Hi-Fi or Dolby Digital system as appropriate

5. Receiver and TV set (Hi-Fi/Dolby Digital system) are switched on (check power indicators)

6. Receiver is responding to remote control

A selection of troubleshooting tips is offered below.

Problem

Cause

Remedy

Consult an antenna specialist

to have it checked and repaired

Antenna signal of satellite as necessary. On “Installation”

reception system missing or menu check LNB conﬁguration

faulty. Incorrect LNB frequencies for the satellite in question:

set in “Antenna Conﬁguration” High L.O. “10.600” GHz, Low L.O.

“Weak or no signal!” warning

appears on some or all channels

menu.

“9.750” GHz, and Limit frequency

L.O. “11.700 MHz”, and change

as necessary.

Set infrared code 1, as described

in operating manual under

“Remote Control RC 660”; check

batteries

Receiver or remote control

command set may have been

unintentionally changed

Remote control no longer

responding

On “Settings” - „Date and Time

Setup“ menu check „Summer

Time Enabled“ and change as

necessary Switch off receiver

at mains switch from current

channel, e.g. ARD or ZDF, wait

10 seconds and then switch back

“Summer Time” setting wrong.

An incorrect time was imported

from the reception signal

Wrong time being displayed

The following channels cut out DECT telephones operate on

or “Weak or no signal!” appears: the same frequency as these

PRO 7, SAT1, Cable 1, DSF, channels. Interference may occur Consult your antenna specialist

N 24, Tele 5, 9 Live, HSE 24 and due to inadequate level or poor

Sonnenklar TV

shielding of cable

Scart

deactivated

pressing the 0 button

connection

TV Keep pressing the 0 button until

Black or blue screen, no on-

screen displays

accidentally the TV picture reappears on-

screen

SERVICE

If, despite studying this operating manual, you still have questions about getting started with the unit or using

it correctly, or if unexpected problems occur, please contact your specialist dealer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Internet: http://www.kathrein.de

KATHREIN-Werke KG • Anton-Kathrein-Straße 1 - 3

P.O. Box 100 444 • 83004 Rosenheim GERMANY

Download from Www.Somanuals.com. All Manuals Search And Download.

Indesit Dishwasher D41 User Manual
Invacare High Chair 1108526 User Manual
Johnson Controls Furnace GG9SMP User Manual
Kenmore Washer 4174110 User Manual
Kenmore Water Heater 153320392 HT User Manual
Kenwood Car Video System DDX7029 User Manual
Kenwood CD Player 382md User Manual
Kenwood Speaker KFC 162MR User Manual
KitchenAid Convection Oven KEMI300V User Manual
Konica Minolta Scanner IC 401 User Manual