Hair Clipper Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
KHC10B
Issue 1/01
Do not use the hair clipper with a
damaged or broken comb nor with teeth
missing from the blades, to avoid injury.
the extension cord or power board
should be positioned so that is not subject
to splashing or contact with moisture.
Use this hair clipper only as described
in this instruction book.The use of
attachments not recommended by the
manufacturer may cause a hazard.
The installation of a residual current
(RCD) is recommended to provide
additional safety protection when using
electrical appliances, It is also advisable
that a RCD with a rated residual
operating current not exceeding 30mA be
installed in the electrical circuit supplying
the bathroom. See your electrician for
professional advice.
Keep blades regularly oiled and clean
blades after each use.
If the appliance is connected to an
extension cord or power board then
Features OfYour Kambrook Hair Clipper
Adjustable blade
control lever for
close trimming and
finishing off
Blade guard – protects
blade when not in use
particularly around
the neck and ears.
Barber’s scissors – quality
stainless steel blades
On/Off switch
Easy hold clipper
Barber’s comb – for
precision cutting control
#4
#3
#2
#1
Blade brush – for cleaning
the cutting blades after use
Trim guide # 1 – for short hair
Trim guide # 2 – for medium hair
Lubricating oil – to keep
blades in peak condition
Trim guide # 3 – for medium – long hair
Trim guide # 4 – for longer hair
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the hair clipper, make sure
the blades are clean and well oiled.
Unwind the cord to its full length, ensure
that the on/off switch is off ‘O’ and plug
the cord into a 230 /240V power outlet,
then turn the power on.
Gently lift the tab at the other end of the
attachment comb and push down until a
click is heard.
Operate the hair clipper with the
ON/OFF switch.
NOTE: For uniform cutting, never push or force the
hair clipper through the hair at a fast speed.The
hair clipper works most efficiently when it works at
its own speed.
Adjustable Lever
Attachment Comb #1 – leaves hair
approx. 3mm (1/8") in length
Attachment Comb #2 – leaves hair
approx. 6mm (1/4") in length
Attachment Comb #3 – leaves hair
approx. 9mm (3/8") in length
Attachment Comb #4 – leaves hair
approx. 12mm (1/2") in length
The adjustable lever adds versatility to
your hair clipper by allowing you to
gradually change the closeness of your cut
without using an attachment comb.
Initially cut only a small amount of hair
until you become accustomed to the
length each attachment comb leaves the
hair.
When the lever is in the uppermost
position, the blade will give you the
closest cut.To increase the cutting length,
push the lever downward gradually.
It is suggested to try the longest
attachment comb on the hair clipper first,
then use the shorter one if a shorter
length is desired.
The lever extends the variety of lengths
that can be achieved with each attachment
comb, by using the varying cutting edges
with each attachment comb.
Attachment Combs
Attachment combs should be fitted to
hair clipper by placing the top edge (comb
edge) of the attachment comb over the
top of the cutting blades.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
UsingYour Kambrook Hair
Clipper
4. If you desire shorter hair, either change
to a lower number attachment comb or
apply more pressure and less lift away
from head with the present attachment
comb.
1. Place a towel around the neck of the
person to prevent hair from falling down
inside the collar.
2. Position the person in a chair so that
his/her head is at your eye level.
5. For the top of the head, you will give a
fairly short cut if you use the #4
attachment comb.With the teeth flat
against the head, slowly start trimming
from the front to the back. (Diagram A-4)
3. Comb the hair to remove all the
tangles, hold the clipper in a relaxed,
comfortable grip to help you maintain
accurate cutting control.
4. Before using the clipper ensure that the
blades are free of any hair clippings and
the blades are well oiled. (See Maintaining
Your Kambrook Clipper on page 6)
Note:The entire procedure requires practice, and it
is always better to leave the hair longer in the first
few haircuts.
Outlining
Medium to Long Cut
(with attachment combs)
B-1
B-2
A-1
A-2
A-3
A-4
1. Outlining requires no attachment comb.
Take the hair clipper and push the
lever up to the close – cut position
1. Start by combing the hair in its natural
direction.
2. Place the largest attachment comb
onto the hair clipper and start by
trimming the sides from the bottom
upwards. Hold the hair clipper lightly
against the hair with the teeth of the
attachment comb pointing up but flat
against the head. Slowly lift the hair
clipper up and outward through the hair,
cutting only a small amount at a time.
(Diagram A-1)
(see “adjustable lever”).
2. Comb hair into the style. Position hair
clipper between the side burns and the
ear. (Diagram B-1)
3. Make sure the corner edge of the blade
is up against the hairline.With the outline
of the hair as your guide, slowly move the
hair clipper over, around and behind the
ears. (Diagram B-2)
4. For the back of the neck and side
burns, hold the clipper up side down, and
holding it against the skin at the length
desired, move downwards.
3. Repeat around sides and back of head.
(Diagram A–2 & A–3)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Short Cuts to Perfect FlatTops,
Crew Cuts
MaintainingYour Kambrook
Hair Clipper
Cleaning
After you have finished using your hair
clipper rapidly move the adjustable lever
up and down a couple of times while the
hair clipper is still running, to remove any
hair that may be caught in between the
blades.Then switch off the appliance and
power outlet.Then unplug your hair
clipper and clean the blades with the
brush supplied.
C-1
C-2
C-3
Oiling
To maintain the hair clipper in peak
condition, the blades should be regularly
oiled before, during and after every
haircut.A substitute/replacement for the
clipper oil supplied in the kit is household
sewing machine oil.
C-4
1.Always cut from the back of the neck to
the crown, using the longest attachment
comb. Holding it flat against the head,
slowly move the hair clipper up through
the hair. (Diagram C-1)
NOTE: Do not use hair oil, grease, oil mixed with
kerosene or solvent, as the solvent will evaporate
and leave the thick oil, which may slow down the
blade motion.
2. Use the same technique for the sides,
cutting from the bottom to the upper side
of the head.
To oil the blades, gently squeeze a few
drops of oil between the blade teeth and
turn the clipper on, checking that the
clipper is running smoothly.
3. From the front to the crown, cut the
hair against the direction in which it
grows.Then even it up with the sides.
(Diagram C-2)
4. For a flat top, use a normal flat comb
and cut hair on top of the head over it.
5.To taper hair down to the neckline, use
closer cutting attachment combs. Comb
hair and check for uneven spots and
outline sideburns and neckline. (Diagram
C-3)
If the blades are dulled and have stopped
cutting, replace them with new blades
from your nearest Kambrook service
centre.
6. If a short tapered cut on the sides and
back is desired, follow the diagram below
and change attachments as illustrated.
(Diagram C-4)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
KAMBROOK
12 MONTH
REPLACEMENT WARRANTY
If the product includes one or a number of
accessories only the defective accessory
or product will be replaced.
KAMBROOK warrants the purchaser
against defects in workmanship and
material, for a period of 12 months from
the date of purchase (3 months
commercial use).
In the event of KAMBROOK choosing to
replace the appliance, the guarantee will
expire at the original date, ie. 12 months
from the original purchase date.
Guarantee and purchase receipt for this
product are to be retained as proof of
purchase and must be presented if making
a claim under the terms of the
In Australia, this KAMBROOK Guarantee
is additional to the conditions and
guarantees which are mandatory as
implied by the Trade Practises Act 1974
and State Territory legislation.
KAMBROOK guarantee.
KAMBROOK reserves the right to
replace or repair the appliance within
the warranty period.
For service, spare parts or product
information in Australia, please call
KAMBROOK on the customer Service
Line (free call) 1800 800 634.
Warranty does not apply to any defect,
deterioration, loss or injury or damage
occasioned by, or as a result of the misuse
or abuse, negligent handling or if the product
has not been used in accordance with the
instructions.The guarantee excludes
breakages and consumable.
For service, spare parts or product
information in New Zealand, please
call KAMBROOK New Zealand, Mono
Place, Ellerslie,Auckland.
Phone 0800 253 007, FAX 0800 263 001.
This warranty is void if there is evidence
of the product being tampered with by
unauthorised persons.
If claiming under this guarantee the product
must be returned to freight prepaid.
YOUR PURCHASE RECORD (Please complete)
Attach purchase receipt here.
DATE OF PURCHASE______________________________________________________
MODEL NUMBER ________________________________________________________
SERIAL NUMBER (If applicable) ______________________________________________
Please don’t return purchase record
unless you are making a claim
PURCHASED FROM ___________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Issue 1/01
Kambrook 4 Kingston Town Close Oakleigh,Victoria 3166,Australia
Customer Service Line (free call) 1800 800 634 Customer Service Fax 1800 621 337
Kambrook (New Zealand) Mono Place Ellerslie,Auckland, New Zealand
Customer Service Line/Spare Parts 0800 253 007 Customer Service Fax 0800 263 001
Due to continual improvement in design or otherwise, the product you purchase may differ slightly from the one illustrated in this book. Issue 1/01
Download from Www.Somanuals.com. All Manuals Search And Download.
|