Jwin Portable CD Player JX M89 User Manual

SPLASH PROOF AM/FM Radio with CD Player  
V10M10_IM_EN_08132007  
Splash-Proof AM / FM Radio with  
CD Player  
TEL: 516-626-7188  
FAX: 516-626-7105  
JX-M89  
INSTRUCTION MANUAL  
© 2007 jWIN Electronics Corp. All rights reserved. No portion of this printed material or product  
enclosed herewith including design, shape and graphics, may be reproduced or transmitted in  
any form without the expressed written consent of jWIN Electronics Corp. by any means,  
electronic or mechanical, including photocopying, recording or use of an information storage  
and retrieval system. Any unauthorized distribution or reproduction of this printed material or  
product, or any portion there of, will be prosecuted to the fullest possible extent of the law.  
Please read this manual carefully before operating and save it for future reference.  
HAVE A QUESTION? PLEASE VISIT WWW.jWIN.COM  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPLASH PROOF AM/FM Radio with CD Player  
V10M10_IM_EN_08132007  
SPLASH PROOF AM/FM Radio with CD Player  
V10M10_IM_EN_08132007  
OPERATIONAL INSTRUCTIONS  
USER SAFETY GUIDE  
IMPORTANT SAFETY INSTRUCTIONS – CONTINUED  
Tips for Getting Better Reception  
11. SERVICING - The user should not attempt to service the appliance beyond that described  
in the user's operating instructions. All other servicing should be referred to qualified  
service professional.  
1. This unit has the built-in AM/FM antennas. Thus, an external FM wire antenna isn’t required to  
be installed on this unit to receive the FM radio. However, if you reside in the poor reception  
area and want to enhance the FM radio reception more, you might attach the pigtail wire  
antenna at the external FM antenna terminal located on the back of the unit.  
2. To get better AM radio reception, be sure to place the unit horizontally and reposition it if there  
are noises on the AM station.  
12. BATTERY USAGE – To prevent battery leakage, which may result in bodily injury,  
property damage or damage to the unit, follow these instructions:  
a. Install all batteries correctly according to the polarity (+ -) as marked on the unit.  
b. Do not mix old and new batteries, carbon and alkaline, etc.  
Cleaning the Unit  
c. Remove batteries from the unit when the device will not be used for an  
extended period of time.  
1. To prevent fire or shock hazard, disconnect your unit from the AC power source when  
cleaning.  
13. LEAD AND MERCURY - This product may contain lead and/or mercury. Disposal of these  
materials may be regulated by your local authorities due to environmental considerations.  
For more detailed disposal or recycling information, please contact your local authorities or  
2. The finish on the unit may be cleaned with a dust cloth and cared for as other furniture,  
Use caution when cleaning and wiping the plastic parts.  
3. If the cabinets become dusty, wipe them with a soft dry dust cloth. Do not use any wax or  
polish sprays on the cabinets.  
4. If the front panel becomes dirty or smudged with fingerprints, it may be cleaned with a soft  
cloth slightly dampened with a mild soap and water solution. Never use abrasive cloths or  
polishes as these will damage the finish of your unit.  
IMPORTANT NOTES  
1. Do not attempt to clean the unit with chemical solvents as this might damage the finish.  
Use a clean, dry cloth.  
Caution: never allow any water or other liquids to get inside the unit while cleaning.  
2. Keep this manual in a safe place for future reference.  
Cleaning the Disc  
1. Treat the disc carefully. Handle the disc only by its edges. Never allow your fingers to  
contact with the shiny, unprinted side of the disc.  
You can help to protect the environment!  
Please remember to respect the local regulations: Hand in the non-working  
electrical equipment to an appropriate waste disposal center.  
2. Do not attach adhesive tape, stickers etc., to the disc label.  
3. Clean the disc periodically with soft, lint-free, dry cloth. Never use detergents or adhesive  
cleaners to clean the disc. If necessary, use a CD cleaning kit.  
4. If disc skips or gets stuck on a section of the disc, it is probably dirty or damaged  
(scratched).  
TO A USER IN USA  
This equipment has been tested and found to comply with the limits for a Radio Receiver,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. This equipment generates,  
uses, and can radiate radio frequency energy and, if not installed and used in accordance with  
the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
5. When cleaning the disc, wipe in straight lines from the centre of the disc to the edge of the  
disc. Never wipe in circular motions.  
6. To remove a disc from its storage case, press down on the centre of the case and lift the  
disc outs, holding it carefully by the edges.  
7. Fingerprints and dust should be carefully wiped off the disc's recorded surface with a soft  
cloth. Unlike conventional records. compact disc have no groove to collect dust and  
microscopic debris, so gently wiping with a soft cloth should remove most particles.  
-
-
-
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Note: Do not use solvents such as benzine petrol, thinner, commercially available cleaners or  
anti-static spray intended for analogue discs.  
-
If necessary, consult the dealer or an experienced radio / TV technician for additional  
suggestions.  
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPLASH PROOF AM/FM Radio with CD Player  
V10M10_IM_EN_08132007  
SPLASH PROOF AM/FM Radio with CD Player  
V10M10_IM_EN_08132007  
USER SAFETY GUIDE  
OPERATIONAL INSTRUCTIONS  
Repeat and Intro Functions-continued  
4. To play the audio tracks in the random order, press the P.MODE button until the indication  
RDM” appears on the LCD screen. The random function is disabled in the programmed  
play mode.  
COMPLIANCE OF FCC RULE  
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that  
this device does not cause harmful interference.  
Note: Changes or modifications not expressly approved by the party responsible for  
compliance could void the user’s authority to operate the equipment.  
Programmed Playback  
SPLASH RESISTANCE  
The PROGRAM function allows your favorite tracks to be played in a programmed sequence.  
This feature can be set in the stop mode or normal play mode.  
1. Press the PROGRAM button to start programming. The indication “PGM” and track  
number “01” start blinking on the LCD screen.  
This unit has been constructed to resist mild steam and light splashes from the shower or bath  
only. It should not be operated under running water and under no circumstances should it be  
fully immersed in water. This unit isn’t a water-resistant device.  
2. Use the SKIP (  
/
) buttons to select your desired track.  
3. After selecting the track, press the PROGRAM button to save the selected track in the  
memory. The indications “PGM” and “02” will appear on the screen and blink while waiting  
for the next input.  
Compatibility  
1. Disc Size: 12cm / 8cm  
AUDIO CD  
2. Disc Type: CD  
4. Repeat step 2 and 3 to program more tracks. You can program up to 20 tracks into the  
memory in any sequence order.  
DISC ERROR  
5. To check the programmed tracks, press the STOP button and then PROGRAM button.  
Each press of the PROGRAM button will show the programmed track accordingly on the  
LCD screen.  
This compact disc player has built-in error compensation circuits to correct for minor defects in  
a disc. There are limits, however, to the amount of correction available. In some cases, the CD  
player may skip some tracks, or parts of tracks, on a disc during disc play. This problem may be  
caused by defects (such as scratches) in the disc being played, which are too large for the error  
compensation circuits to handle. If you encounter this problem, try a new disc before having the  
unit serviced. If the CD player operates normally, the skipping problem is probably due to a  
defective disc.  
6. Press the PLAY / PAUSE ( ) button to start the programmed playback.  
7. To cancel the programmed play, press the STOP button twice.  
Listening to Radio  
1. Set the FUNCTION select switch to the "RADIO" position.  
2. Set the BAND select switch to either "AM" or “FM”.  
Note: Only the above types of discs can be played on this unit. Some CD-R, CD-RW discs cannot be  
3. Adjust the TUNING knob to obtain the desired radio station.  
4. Adjust the VOLUME control knob to obtain the desired sound level.  
5. To turn off the radio, set the FUNCTION select switch to the "CD" position.  
played depending on the condition of the player and the disc.  
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPLASH PROOF AM/FM Radio with CD Player  
V10M10_IM_EN_08132007  
SPLASH PROOF AM/FM Radio with CD Player  
V10M10_IM_EN_08132007  
OPERATIONAL INSTRUCTIONS  
GETTING STARTED  
Playing an audio CD  
Thank you for purchasing JX-M89. Unpack the package and make sure all the accessories and  
main unit are put aside so they will not be lost. We recommend that you retain the original  
carton and packaging materials for future use, should you transport or ship the unit in the future.  
1. Set the FUNCTION select switch to the "CD" position.  
2. Press the PUSH OPEN button to open the CD compartment cover.  
3. Load an audio CD with the label side facing out.  
Splash-proof AM / FM radio with CD Player  
4. Close the cover. Ensure that the cover is firmly locked.  
Circular mirror on the front  
5. Press the PLAY / PAUSE ( ) button. The indication “- -” will appear on the LCD screen.  
A few seconds later, the total number of audio tracks on the CD will briefly appear on the  
LCD screen and then automatically start playing from the first track.  
Completely self-contained for portable operation  
Variable CD play modes: Repeat 1, Repeat All, Random, Program, Intro  
Programmable memory for 19 audio tracks  
Round-shape Liquid Crystal Display (LCD)  
Integrated AM/FM tuner  
Built-in powerful speakers  
CD-R / CD-RW playback  
6. Adjust the VOLUME CONTROL knob to obtain the desired sound level from the speakers.  
7. To pause while playing, press the PLAY / PAUSE ( ) button. The  
track number will flash to indicate that the unit is in the pause mode.  
To resume the playback, press the PLAY / PAUSE ( ) button again.  
8. To stop the playback, press the STOP () button.  
What’s Included  
Audio CD player  
Instruction manual  
Warranty Card  
9. To turn off the player, press the STOP button in the stop mode. Or if  
the CD player is left in the stop mode for more than 30 seconds, it will  
automatically turn itself off to save the power.  
External FM antenna  
Skip and Search Functions  
1. Press the SKIP + ( ) button once to skip a track forward.  
2. Press and hold the SKIP + ( ) button to search a track forward.  
3. Press the SKIP – (  
) button twice consecutively to skip a track backward. If pressed  
once, it will skip to the beginning of the current track, not to the beginning of the previous  
track.  
4. Press and hold the SKIP – (  
) button to search a track backward.  
Repeat and Intro Functions  
1. To repeat the current track, press the P.MODE button until the indication “RPT1” appears  
on the LCD screen.  
2. To repeat the entire CD or all the programmed tracks, press the P.MODE button until the  
indication “RPT ALL” appears on the LCD screen.  
3. To start the INTRO playback, press the P.MODE button until the indication “INTRO”  
appears on the LCD screen. If the player is in the play mode when it is set to the INTRO  
mode, the indication “INTRO” will be shown but blinking. In this case, the INTRO function  
will be in effect with the next track. If the player is in the stop mode when it is set to the  
INTRO mode, the indication “INTRO” will be shown. Press the PLAY / PAUSE ( ) button  
to start the INTRO play. The first 10 seconds of each track will be played.  
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPLASH PROOF AM/FM Radio with CD Player  
V10M10_IM_EN_08132007  
SPLASH PROOF AM/FM Radio with CD Player  
V10M10_IM_EN_08132007  
GETTING STARTED  
GETTING STARTED  
Using an AC Adapter to Supply the Power to the Unit  
Location of Controls on the Main Unit  
Before connecting the AC adapter (not included), make sure that the input voltage of the AC  
adapter corresponds to your local AC outlet voltage. It is recommended to use an AC adapter,  
which outputs DC 9V / 600mA /  
, for this unit.  
1. Connect the plug of the AC adapter to the DC 9V socket of JXM89.  
2. Connect the other end of the AC adapter to the wall outlet.  
Important Note: To avoid the electric shock or fire, do not use the AC adapter where lots of  
water particles exist in the air. Use the AC adapter with caution.  
1.  
LCD screen (CD mode).  
Installing batteries for the portable use  
2. Circular mirror.  
3. TUNER dial pointer.  
4. PUSH OPEN button for CD compartment cover.  
5. CD compartment cover.  
6. RELEASE button for circular mirror.  
7. VOLUME CONTROL knob.  
8. TUNING knob (Radio mode).  
9. BAND select switch (Radio mode)  
Used to select the radio band (AM or FM).  
10. FUNCTION select switch.  
This unit operates on 6 “C” (or UM-2) batteries (not included) for the portable use.  
1. Open the BATTERY COMPARTMENT cover. The  
BATTERY COMPARTMENT is located on the back  
of the unit.  
2. Insert 6 “C” alkaline batteries, following the polarity  
as indicated in the BATTERY COMPARTMENT.  
3. Close the BATTERY COMPARTMENT cover.  
Important Note: Please protect the environment. Dispose of old batteries properly throw the  
Used to select the CD mode or the RADIO mode.  
11. PROGRAM. button (CD mode).  
according to your local regulations.  
Used to program audio tracks to play in a preferred playback order.  
12. P.MODE button (CD mode).  
Used to change to the specific playback mode (Repeat 1 / Repeat All / Intro / RDM).  
13. SKIP – (  
) button (CD mode).  
a. Used to skip to the previous audio track by pressing it while playing a CD.  
b. Used to search an audio track by pressing and holding it while playing a CD.  
14. SKIP + ( ) button (CD mode).  
a. Used to skip to the next audio track by pressing it while playing a CD.  
b. Used to search an audio track by pressing and holding it while playing a CD.  
15. STOP () button (CD mode).  
a. Used to stop the playback while playing.  
b. Used to power off the unit in the stop mode.  
16. PLAY / PAUSE ( ) button (CD mode).  
a. Used to start the playback or pause while playing.  
b. Used to power on the unit in the power-off mode.  
17. DC 9V socket.  
18. Terminal for the external FM radio antenna.  
19. LOCK for battery compartment cover.  
20. Hanging rope.  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  

Intel Computer Hardware 80C51FA User Manual
Intel Microscope Magnifier 80C196NU User Manual
IOGear Games GCE700 User Manual
Jabra Bluetooth Headset GN2100 User Manual
Jensen Lathe JHD1000 User Manual
John Deere Snow Blower st0524 User Manual
Kensington Tablet Accessory K72437 User Manual
KitchenAid Double Oven W10526086A User Manual
Kodak Film Camera EXR 500T User Manual
Kramer Electronics Camcorder SP 11 User Manual