WARNING:
IF THE INFORMATION IN THESE INSTRUCTIONS
ARE NOT FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
FOR YOUR SAFETY:
DO NOT STORE OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS AND LIQUIDS IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE.
INSTALLATION:
GF 3 BV
ALLAGASH
INSTALLATION AND SERVICE MUST BE
PERFORMED BY A QUALIFIED INSTALLER,
SERVICE AGENCY OR LICENSED GAS SUPPLIER.
WHAT TO DO IF YOU SMELL GAS:
B-Vent Gas Heater
• DO NOT TRY TO LIGHT ANY APPLIANCE.
• DO NOT TOUCH ANY ELECTRICAL
SWITCHES.
• DO NOT USE THE PHONE IN YOUR
BUILDING. IMMEDIATELY CALL YOUR GAS
SUPPLIER FROM A NEIGHBOR’S PHONE.
• FOLLOW YOUR GAS SUPPLIER’S
INSTRUCTIONS.
• IF YOU CANNOT REACH YOUR GAS
SUPPLIER, CALL THE FIRE DEPARTMENT.
AVERTISSEMENT:
ASSUREZ-VOUS DE BIEN SUIVRE LES
INSTRUCTIONS DANS CETTE NOTICE POUR
REDUIRE AU MINIMUM LE RISQUE D’INCENDIE
OU POUR EVITER TOUT DOMMAGE MATERIEL,
TOUTE BLESSURE OU MORTALIT’E.
NE PAS ENTREPOSER NI UTILISER D’ESSENCE
NI OU LIQUIDES INFLAMMABLES DANS LE
VOISINAGE DE CET APPAREIL OU DE TOUT
AUTRE APPAREIL.
L’INSTALLATION LE SERVICE DOIVENT ETRE
EXECUTES PAR UN INSTALLATEUR
QUALIFIE, AGENCE DE SERVICE OU LE
FOURNISSEUR DE GAZ.
Installation
and Operation
Instructions
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ.
• NE PAS TENTER D’ALLUMER L’APPAREIL
• NE TOUCHEZ A AUCUM NTERRUPTEUR.
• NE PAS VOUS SERVIR DES TELEPHONES SE
TROUVANT DANS LE BATIMENT OU VOUS
VOUS TROUVEZ.
• APPELEZIMMEDIATEMENTVOTRE
FOURNISSEUR DE GAZ CHEZ UN VOISIN. SUIVEZ
LESINSTRUCTIONSDUFOURNISSEUR.
Warnock Hersey
C
US
• SI VOUS NE POUVEZ REJOINDRE LE
FOURNISSEUR DE GAZ, APPELEZ LE SERVICE
DES INCENDIES.
Download from Www.Somanuals.com. All Manuals Search And Download.
WELCOME TO JØTUL:
Congratulations on the purchase of your new
Jøtul gas stove.
We at Jøtul are very happy you have made the
decision to warm your hearth with a Jøtul product.
Your new Jøtul Allagash has inherited the benefits
learned from more than 140 years of producing
stoves. Jøtul is the world’s largest manufacturer
of solid fuel burning appliances and has been
making cast iron wood and coal stoves since 1853.
28”
The Allagash incorporates the most advanced gas
technology with the warm traditional style of cast
iron. With proper care and operation, your new
Jøtul will last many, many years.
22 3/4”
The Jøtul Allagash gas stove is a gravity vented
gas fireplace heater. The Allagash B-Vent gas
stove can only be vented vertically directly to
the outside, using type B-vent pipe.
HEIGHT
OF TOP
EXIT IS
CENTER
OF REAR
EXIT IS
23”
27 1/2”
The Jøtul Allagash gas stove is designed to operate
on NATURAL GAS or PROPANE only. For
safe and efficient operation the stove is equipped
with a millivolt gas control valve with a piezo
ignitor. Electrical power is only required when
operating the OPTIONAL forced air blower, if
installed on the stove (part # 129161).
13 1/4”
Input Rates
The input rate on the Allagash gas stove is 24,000
BTU/hr maximum input on the high setting for
both natural gas and propane, adjusted down to
19,000 BTU/hr minimum on the low setting, for
both natural gas and propane.
4”
18 1/2”
Natural gas
24,000 BTU/hr. maximum input
19,000 BTU/hr. minimum input
Propane
24,000 BTU/hr. maximum input
19,000 BTU/hr. minimum input
22 3/4”
3
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARDS:
The installation must conform to local codes. Your
local Jøtul dealer can assist you in determining
what is required in your area for a safe and legal
installation. Some areas require a permit to install
a gas burning appliance. Always consult your local
building inspector or authority having jurisdiction
to determine what regulations apply in your area.
This appliance complies with National Safety
standards and is tested and listed by ITS,
Intertek Testing Services
Middleton, WI
In addition, the Allagash gas stove complies with REMEMBER Your local officials have final
and has been tested and listed as a gravity vented authority in determining if a proposed installation
gas fieplace heater and listed to:
is acceptable. Any requirement that is requested
by the local authority having jurisdiction, that is
not specifically addressed in THIS manual,
defaults to local code. In the absence of local
codes, the installation requirements must comply
ANSI Z21.88-1998(NFPA 54)
CSA 2.33-M98 for Canada.
DO NOT ATTEMPT TO ALTER OR with the current National codes. In the U.S. these
MODIFY THE CONSTRUCTION OF THE requirements are established in the National Fuel
APPLIANCE OR ITS COMPONENTS. ANY Code, ANSI Z223.1.(NFPA 54). In Canada, the
MODIFICATION OR ALTERATION WILL codes have been established in CAN/CGA B149
VOID THE WARRANTY, CERTIFICATION Fuel Installation Code.
AND LISTING OF THIS APPLIANCE.
Installer l’appareil selon les codes ou reglements
GENERAL INFORMATION:
locaux, ou, en l’absence de tels reglements, selon
les Codes d’installation CAN/CGA-B149.
THIS HEATER MUST BE INSTALLED
AND MAINTAINED BY A QUALIFIED DO NOT OPERATE THIS STOVE IF ANY
SERVICE AGENCY. PART HAS BEEN UNDER WATER.
The installation and repair of this appliance must Immediately call a qualified service technician
be done by a qualified service person. Failure to inspect the heater and to replace any part of
to properly install and maintain this heater could the control system and any gas control which has
result in an unsafe or hazardous installation, been under water.
which may result in a fire, explosion, property
damage, personal injury or loss of life.
Ne pas se servir de cet appareil s’il a ete’ plonge
dans l’eau, completement ou en partie. Appeler
This appliance should be inspected before use un technicien qualifie pour inspecter l’appareil et
and at least annually. More frequent cleaning remplacer toute partie du syste’me de controle et
may be required due to excessive lint from toute commande qui ont ete plonges dans l’eau.
carpeting, bedding material, etc. It is imperative
that control compartments, burners and Do not operate the Allagash gas stove with the
circulating air passageways of the appliance be glass front removed, cracked or broken.
kept clean.
Replacement of the glass should be done by a
licensed or qualified service person. Only remove
S’assurer que le bruleur et le compartiment des glass for routine service. Always handle glass
commandes sont propres. Voir les instructions carefully.
d’installation et d’utilisation qui accompagnent
l’appareil.
Pour utilisation avec les portes en verre cerifiers
aved l’appareil seulemend ou Ne pas utiliser avec
des portes on verre.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot Surfaces
THIS APPLIANCE MUST NOT BE
The Allagash gas stove will, during normal CONNECTED TO A CHIMNEY OR FLUE
operation, reach high surface temperatures SERVING ANY OTHER APPLIANCE OF
therefore:
ANY KIND.
·
·
Due to the high operating temperatures this LOCATION:
appliance should be located out of traffic
and away from furniture and draperies.
In selecting the location, the aesthetic and
Children and adults should be alerted to the functional use of the appliance are primary
hazards of high surface temperatures and concerns; However, proper venting systems and
should stay away to avoid burns or clothing access to the fuel supply are also important issues.
ignition.
Due to the high surface temperatures of the
·
·
·
·
·
·
Young children should be supervised while Allagash, always consider the proximity of traffic
they are in the same room as the Allagash ways, furniture, draperies, etc.
gas stove.
Clothing or other flammable materials This appliance may be located on or near
should not be placed ON or NEAR the conventional construction materials. HOWEVER,
Allagash gas stove.
always maintain the proper clearances to
Surveiller les enfants. Garder les vetements, combustibles, as this provides adequate
les meubles, l’essence ou autres liquides a ventilation air around the appliance.
vapeur inflammables loin de l’appareil.
NEVER store or use gasoline or any other The following clearances and hearth requirements
flammable vapors or liquids in the vicinity are the minimum requirements when installing
of the Allagash gas stove.
the Allagash gas stove near or on combustible
Never burn any other materials in your surfaces. Always provide adequate access around
Allagash gas stove, it is strictly designed for the appliance for servicing and proper operation.
use with natural gas or propane fuel ONLY.
Any safety screen, glass or guard removed A combustible surface is anything that can burn
for servicing the appliance must be replaced (i.e. sheet rock, wall paper, wood, fabrics etc.).
prior to operating the appliance.
These surfaces are not limited to those that are
visible and also include materials that are behind
non-combustibles.
Blower/Electrical Hazard
When the Allagash gas stove is installed with the
optional forced air Blower Kit (part #129161) the If you are not sure of the combustible nature of
stove must be electrically grounded in accordance a material, consult your local fire officials.
with local codes or, in the absence of local codes, Remember, “Fire Resistant” materials are
with the current NFPA 70- National Electrical considered combustible: they are difficult to
Code or CSA C22.1-Canadian Code.
ignite, but will burn. Also, “fire-rated” sheet rock
is considered combustible.
The Allagash Blower Kit is already supplied with
a three-prong (grounding) plug for protection The Allagsh B-Vent gas stove is not to be
against shock hazard and should be plugged connected or installed using any warm air duct
directly into a properly grounded three-prong system.
receptacle.
Always maintain the proper clearances to the
DO NOT CUT OR REMOVE THE appliance for the proper flow of combustion and
GROUNDING PRONG FROM THE PLUG.
Always unplug the Blower when performing
routine service to the Allagash gas stove.
ventilation air to the stove.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FLOOR PROTECTION:
PARALLEL INSTALLATION
The Allagash gas stove CANNOT be installed
directly on carpeting, vinyl flooring, linoleum or
Pergoã.
2” (50mm) from
draft hood
If it is desired to install this appliance on any
combustible material OTHER THAN WOOD,
a floor pad must be installed that is either metal,
wood or a listed hearth pad. This floor protection
must extend the full width and depth of the
appliance. It is not necessary to remove the
carpeting, vinyl or linoleum from underneath the
4”
(102 mm)
10”
(255mm)
left side
wall
right side
wall
floor protection.
Minimum hearth protection
under the Allagash B-Vent gas
stove:
CORNER INSTALLATION
22 3/4” wide X 18 3/4” deep
3”
76mm
Note: the hearth requirements are the same when
using the optional short leg package.
STOVE CLEARANCES:
3”
76mm
Minimum clearances for the Allagash B-Vent
gas stove are as follows:
Rear clearance =2”(50mm)
(measured from draft hood)
Ceiling =18”(460mm)
(measured from top of stove)
Corner clearance =3”(76mm)
(measured from rear corners)
MANTEL, CEILING AND TRIM
Right side clearance = 4”(102mm)
Left side clearance = 10” (255mm)
(for access to the lighting instructions)
MANTEL OR
TRIM DEPTH
19”or greater in depth
All venting components must be installed in
accordance with the terms of their listing and
manufacturer’s instructions. Refer to the pipe
manufacturer’s instructions for proper pipe
clearances. Any horizontal venting requires a
2” (50mm) top clearance off top of pipe.
6”- 18” in depth
2”- 5” in depth
A
B
C
1” trim only
ALCOVE
MINIMUM
CLEARANCES TO TOP
PLATE OF STOVE
Minimum Alcove Width = 41”(1042mm)
(minimum side clearance in an alcove becomes 8”
on right side of stove and 10” on left side of stove).
Maximum Alcove Depth = 24”(610mm)
Minimum Alcove Height (off stove)= 18”(460mm)
(minimum height off top casting of stove).
A = 18”
B = 12”
C = 5”
(460mm)
(305mm)
(127mm)
1” trim = 1” (25mm)
Pipe clearances =see manufacturer’s listing.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
• Any UNUSED flue or masonry enclosure can be
used as a passage way for venting the Allagash:
PROVIDED the flue is relined using Type B
4” vent or Listed Flexible Gas Liner.
VENTING REQUIREMENTS:
The Allagash is specifically designed to operate
using 4” Type B vent pipe components or a Listed
Flexible gas liner.
• The remaining space around the liner in a
masonry or zero-clearance flue CANNOT be
used to vent any other appliance.
FOLLOW THE GUIDELINES LISTED
BELOW FOR THE PROPER VENTING OF
THE ALLAGASH B-VENT STOVE!
• When terminating through the roof refer to the
Gas Vent Rule for proper vent termination
height. See Figure 1.
• All venting components must be installed in
accordance with the terms of their listing and
manufacturer’s instructions.
• The minimum height of a vertically terminated
system shall be no less than 7', and the
maximum height shall be no more than 35'.
See diagrams page 9.
• With steep roofs, nearby trees, and in
predominant windy conditions, poor draft or
down draft conditions can occur. In these cases,
increasing the height of the vent or high wind
termination caps may improve the situation.
• ELBOWS: If an offset or elbow is necessary
in the vertical rise, it is important to support
the vent pipe every three feet, to avoid excessive
stress on the offsets.
Figure 1
• Whenever possible use 45° elbows opposed to
90° elbows. This offers less restrictions for the
flow of flue gases.
• NO venting can terminate horizontally or
below roof eaves.
Maximum number of 90° elbows = three
Maximum number of 45° elbows = four
• Passage through combustibles (walls, ceilings)
must be with Type B venting and must
maintain listed clearances.
• TOTAL MAXIMUM HORIZONTAL
RUN ANYWHERE IN THE VENTING
CONFIGURATION IS 4 FEET. The distance
between any 45° elbows is considered a
horizontal run. See diagrams page 9.
• It is recommended that any horizontal runs
have an upward slope of 1/4” per foot toward
the termination cap.
• Any Type B vent passing through a roof must
have a flashing, storm collar, thimble and a
Type B cap is required. See diagrams page 9.
• When venting through a thimble into a
masonry flue any venting exposed in the room
must be Type B venting.
• Venting on the Allagash CANNOT be less than
• Listed Flexible Gas Liners may not be exposed
4” in diameter or greater than 4” in diameter.
in any living space.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
• When decorative 6” pipe is installed to cover
the venting any Listed Flexible Gas liner must
be connected directly to the stove’s draft hood.
Allagash B-Vent gas stove vented into a
masonry or prefabricated fireplace.
Listed termination
cap required
• Use of single wall connector pipe as a vent is
prohibited for use with theAllagash B-Vent stove.
Storm collar
required
• A firestop is required at every floor.
Top sealing
achor plate
• Any venting that is exposed above the first
floor, regardless of attic space or living space,
must be enclosed. Always maintain the
required clearance from all sides of the vertical
vent system according to manufacture.
Type B vent or
Listed Flexible
Gas Liner. On
outside chimneys
Jøtul recommends
the use of Type B
vent to help keep
the gases warm and
rising.
• Installation of any components not
manufactured or approved by Jøtul or failure
to meet all clearance requirements will void
all warranties and could result in property
damage, bodily injury, or serious fire.
• Never modify any venting component, or use
any damaged venting product.
max. height 35’
min. height 7’
• THE GAS APPLIANCE AND VENT
SYSTEM MUST BE VENTED DIRECTLY
TO THE OUTSIDE OF THE BUILDING,
Always maintain
the proper
clearance to mantel
and trim
AND NEVER ATTACHED TO
A
CHIMNEY SERVING A SOLID FUEL OR
GAS BURNING APPLIANCES.
Maximum
offset is 4’
• BE SURE TO MAINTAIN THE PROPER
CLEARANCES TO COMBUSTIBLES AS
DEFINED IN THIS MANUAL AND IN
THE INSTRUCTIONS PROVIDED WITH
EACH VENTING COMPONENT.
Recommended
damper sealing plate
to seal flue chamber
to prevent heat loss
• When installing at an altitude above 2000’ the
minimum vertical rise becomes 12’ from the
draft hood.
Allagash B-Vent gas
stove
• If more than two feet of venting is exposed to
the outside, the entire exterior vent system
must be enclosed in an insulated chase system.
WARNING: FAILURE TO POSITION THE PARTS IN
ACCORDANCE WITH THIS DIAGRAM OR FAILURE TO USE
ONLY PARTS SPECIFICALLY APPROVED WITH THIS
APPLIANCE MAY RESULT IN PROPERTY DAMAGE OR
PERSONAL INJURY.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING CONFIGURATIONS FOR THE
ALLAGASH B-VENT
Listed B-Vent
termination cap
required.
Listed B-Vent
termination cap
required.
Maximum total
horizontal
anywhere in
venting
configuration
is 4 feet.
Maximum
chimney height
off draft hood
= 35 feet.
45° or 90°
elbow
Minimum
NOTE:
When installing
at an altitude
above 2000’ the
minimum
vertical rise
becomes 12’
from the draft
hood.
chimney height
off draft hood
= 7 feet.
Minimum
chimney height
off draft hood
= 7 feet.
45° or 90°
elbow
NOTE:
When installing
at an altitude
above 2000’ the
minimum
vertical rise
becomes 12’
from the draft
hood.
Minimum chimney on the Allagash
B-Vent top vent or rear vent = 7 feet.
Maximum horizontal offset anywhere in
venting configuration; rear vent or top vent
directly on the stove or further up
45° or 90° elbows = 4 feet.
Maximum horizontal offset anywhere in
venting configuration; rear vent or top vent
directly on the stove or further up
45° or 90° elbows = 4 feet.
Maximum # of elbows;
90°= three
45°=four
Listed B-Vent termination cap always required.
Listed B-Vent
termination cap
required.
Listed B-Vent
Maximum total
termination cap
horizontal offset
required.
anywhere in
venting
configuration is
NOTE:
When installing
at an altitude
45° or 90°
elbow
4 feet.
above 2000’ the
minimum
vertical rise
becomes 12’
from the draft
hood.
Minimum
chimney height
off draft hood
= 7 feet.
45° or 90°
Minimum
elbow
chimney height
off draft hood
= 7 feet.
45° or 90°
elbow
45° or 90°
elbow
NOTE:
When installing
at an altitude
above 2000’ the
minimum
vertical rise
becomes 12’
from the draft
hood.
Maximum
horizontal
offset
anywhere in
venting
configuration
is 4 feet.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS CONVERSION:
Tools required:
1/4” Nut driver, 7/16” and 1/2” open end
The Allagash B-Vent gas stove is shipped from wrench or deep well socket, 4mm allen
the factory equipped as a NATURAL GAS unit; wrench, Torx t20 or slotted screwdriver.
However, the stove is shipped with the necessary
gas conversion kit to convert the stove to burn Included in the conversion kit:
PROPANE GAS. These kits contain all the 1 regulator tower labeled for propane
necessary components needed to complete the 3 regulator tower screws
task and ensure safe operation, including labeling 1 burner orifice (#54 LPG)
that must be affixed to the stove.
1 pilot orifice ( #30 for LPG, #51 for NG)
Label A - to be completed and adhered to the
back of the stove.
WARNING:
THE CONVERSION KIT IS TO BE INSTALLED BY
AN AUTHORIZED JØTUL SERVICE TECHNICIAN
Label B - to adhere to the stove’s rating plate.
IMPORTANT:
IN
ACCORDANCE
WITH
THE
If the forced air blower kit is installed, be sure
to unplug blower before proceeding with this
conversion. Any gas supply must be turned
off and disconnected from the valve.
MANUFACTURER’S INSTRUCTION AND ALL
CODES AND REQUIREMENTS OF THE
AUTHORITY HAVING JURISDICTION. FAILURE
TO FOLLOW THESE INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR PROPERTY
DAMAGE.
THE QUALIFIED AGENCY
Conversion instructions are also shipped in the
stove with the conversion kit.
PERFORMING THIS WORK ASSUMES
RESPONSIBILTY FOR THIS CONVERSION.
Gas Conversion Procedure
1. Turn off gas supply to the stove.
2. Lift off top plate (5).
IN CANADA:
THE CONVERSION SHALL BE CARRIED OUT IN
ACCORDANCE WITH THE REQUIREMENTS OF
THE PROVINCIAL AUTHORITIES HAVING
JURISDICTION AND IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN1-B149.1 AND
.2 INSTALLATION CODE.
3. Release the glass clips atop the stove and
slowly lift glass panel (10) up and out of track.
Cet equipement de conversion sera installe par
une agence qualifiee de service conformement aux
instructions du fabricant et toutes exigences et
codes applicables de l’autorises avoir la
juridiction. Si l’information dans cette Instruction
n’est pas suivie exactement, un fey, explosion ou
production de protoxyde de carbone peut resulter
blessure personnelle de vie. L’agence qualifiee
de service est esponsable de l’installation n’est
pas propre et complete jusqu’a l’operation de
l’appareil converti est cheque suivant les criteres
etablis dans les instructions de proprietaire
provisionnees avec l’equipement.
4. Remove the log set (12) using care not to
scratch or damage logs.
5. Lift out the log support (14). Remove the air
divider (15) by lifting the right side and slowly
rotating forward.
6. Remove burner tube (13): Using a ¼” nut
driver remove the two screws securing the
burner tube (13) to the stove bottom. Lift out
the burner tube.
7. Change the main burner orifice. Using a ½”
open end wrench or deep well socket remove
the burner orifice and replace with the
appropriate orifice, supplied in the kit.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Adjust the air shutter on the burner tube to allow 11. Change the variable regulator on the valve (Hi/
for the proper mixing of air and gas. See Figure 2.
The correct settings: natural 1/4” open
propane 1/4” open
Loknob). UsingaTorx t-20screwdriver,remove
the three specialty screws from the front of the
valve regulator. See Figure 4.
12. Remove the regulator tower and the gasket.
BE SURE TO REMOVE THE BLACK
RUBBER GASKETS FROM THE VALVE!!!
See Figure 4.
AIR SHUTTER
Figure 2
BURNER TUBE
13. Install the new variable regulator tower with
the new rubber gasket.
Thoroughly tighten new
regulator to valve body.
ATTENTION: Air shutter should never be
LESS than 1/8” open.
BESURETOREMOVE
THE BLACK RUBBER
GASKET FROM THE
VALVE!!!
WHENRE-INSTALLINGTHEBURNERTUBEBESURE
THAT THE TUBE IS PULLED FORWARD IN THE
MOUNTING HOLES, SECURE WITH THE TWO 1/4”
SCREWS.
9. Change the pilot orifice. FROM WITHIN
THE FIREBOX, PULL THE PILOT
HOOD OFF THE PILOT ASSEMBLY.
Using a 4mm allen wrench thread out the pilot
orifice (counter clockwise). Replace with the
appropriate orifice: See Figure 3.
Figure 4.
#51or natural gas
#30 for propane
Tighten orifice into the base of the pilot
assembly. Be sure the orifice is threaded tightly
and flush with the base.
14. Install the identification labels to the stove so
that they can be seen by any person that may be
servicing the stove.
15. Reassemble the stove, apply gas to the system
and check for gas leaks including all stove lines
before and after the valve.
10. Replace pilot hood onto pilot assembly.
NEVER USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
PILOT HOOD
ATTENTION!! ATTENTION!!
This is very important
Correct gas pressure is essential for efficient and
safe operation of the Allagash B-Vent gas stove.
It is important that the correct gas pressure be
established at the time of the installation. For
more details, see the Gas Pressure section of this
manual on page 13.
PILOT
ORIFICE
PILOT ORIFICE
SCREWS INTO
BASE
ALWAYS REFER TO THE LIGHTING
INSTRUCTIONS ON PAGE 23 OF THIS
MANUAL WHEN LIGHTING YOUR
ALLAGASH.
Figure 3.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAKING THE GAS CONNECTION:
Secure all joints tightly using appropriate tools
and sealing compounds (for propane units, be sure
to use compounds that are propane resistant).
Turn on gas supply and test for gas leaks using a
soapy water solution. Never use an open flame
to check for leaks.
NOTE: IF THE OPTIONAL FORCED BLOWER KIT
(PART # 129161) IS TO BE INSTALLED ON THE
STOVE AT THE TIME OF THE INSTALLATION
OR IN THE FUTURE, THE GAS SUPPLY LINE
SHOULD BE INSTALLED AS CLOSE TO THE
FLOOR AS POSSIBLE.
Leak test:
·
·
Mix a 50-50 solution of water and dish soap.
Light appliance- see lighting instructions on
page 23 of this manual or on the stove’s rating
plate.
USE OF A 90° ELBOW DIRECTLY OFF THE VALVE
WILL ALLOW FOR PROPER CLEARANCE FOR
THE BLOWER.
·
·
Brush or spray all joints and connections with
the soapy water solution.
If bubbles appear at any connection or seam
or a gas odor is detected, immediately turn
gas control knob to the OFF position.
The gas supply line connection is made to the valve
just inside the left rear leg. The Gas supply line
should be a minimum of 3/8" in diameter, or
the appropriate size to provide sufficient gas
pressure to the valve regardless of the input
setting.
Tighten or reconnect the leaking joint and retest
for any gas leaks.
The use of Flexible Gas Appliance Connectors is
acceptable in many areas in the U.S.; However,
Canadian methods vary depending on local code.
GAS PRESSURE:
Correct gas pressure is essential for efficient and
safe operation of the Allagash gas stove. It is
important that the correct pressure is established
at the time of the installation.
ALL INSTALLATIONS MUST COMPLY
WITH LOCAL CODE OR IN THE ABSENCE
OF LOCAL CODE, MUST COMPLY WITH
THE MOST RECENT EDITION OF THE
NATIONAL FUEL GAS CODE ANSI Z223.1/
NFPA 54 OR CAN-B149.
Proper gas pressure provides a consistent flow of
gas to the appliance and is instrumental in
checking for gas leaks.The gas control valve on
the stove is equipped with pressure test points
for gauge connections. The gauge connections
are located on the front of the valve under the
On/Off/Pilot- knob. Gauge connections are
identified by:
All codes require: a gas shut-off valve (gas cock)
and union, to be installed in the supply line, and
in the same room as the appliance. This allows
for the disconnection of the stove for servicing
and maintenance. See Figure 5.
E for inlet or supply pressure (the amount of
gas coming to the valve.)
A for manifold pressure (the amount of gas that
is coming out of the valve to the burner.)
Figure 5
E A
T-handle gas cocks are required in Massachusetts
in compliance with code 248CMR.
Pressure test point as located on the front of the valve.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The appliance must be isolated from the gas supply
line by closing its individual manual gas shut-off
valve (gas cock) during any pressure testing of
the gas supply piping system that is equal to or
exceeds pressures of 1/2 psig (3.5kPa).
HIGH ALTITUDE INSTALLATIONS:
When installing the Allagash in high altitude
(above 2000') situations it becomes necessary to
compensate for the thinner air (less volume of
air per cubic foot). Higher altitudes effect the
atmospheric pressure and heat value of gaseous
fuels. The lower oxygen content in the air and
the lower gas viscosity require the use of a
different orifice to achieve efficient, clean
combustion at the burner tube.
NECESSARY INLET GAS PRESSURES
(inches water column)
MIN
MAX
NATURAL GAS
PROPANE
5.0 WC
7.0 WC
11.0 WC 13.5 WC
In the U.S.
THE DERATING KIT MUST BE INSTALLED BY
AN AUTHORIZED SERVICE TECHNICIAN IN
ACCORDANCE WITH THE MANUFACTURER’S
INSTRUCTIONS AND ALL CODES AND
REQUIREMENTS OF THE AUTHORITY HAVING
JURISDICTION. THE INFORMATION STICKER
MUST BE FILLED OUT BY THE INSTALLER AND
ADHERED TO THE APPLIANCE AT THE TIME
OF THE CONVERSION. THE QUALIFIED SERVICE
AGENCY PERFORMING THIS WORK ASSUMES
RESPONSIBILITY FOR THIS DERATING.
NECESSARY MANIFOLD PRESSURES
(inches water column)
MIN
MAX
3.5 WC
10.0 WC
NATURAL GAS
PROPANE
2.2 WC
6.5 WC
ALWAYS TEST PRESSURES WITH VALVE
CONTROL KNOB SET ON HIGH
In Canada
THIS UNIT HAS BEEN TESTED FOR
INSTALLATION AT HIGH ALTITUDES IN
ACCORDANCE WITH CANADIAN TEST
STANDARD CAN/CGA-2.17.THE DERATING
SHALL BE CARRIED OUT IN ACCORDANCE
WITH THE REQUIREMENTS OF THE
Symptons of incorrect gas pressure include:
Insufficient gas pressure:
• Small pilot flame which can result in
insufficient millivolts.
• Little variation in flame picture between HI
and LO settings.
• Insufficient gas to support more than one
appliance causing nusance outages or gas
surges.
PROVINCIAL
AUTHORITIES
HAVING
JURISDICTION AND IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN1-B-149.1
AND .2 INSTALLATION CODE.
For installations from 2000ft.(610m) to
4500ft.(1370m) the orifice size for:
natural gas is a #42
propane gas is a #55
SEE THE HIGH ALTITUDE ORIFICE CHART
Excessive gas pressure:
• Permanent damage to valve causing complete
appliance shut down.
• Too large a pilot flame resulting in over heating
of the power generator causing shut down.
• Sooting due to impingement and/or incorrect
fuel to air mix.
on page 14.
For high altitude installations consult the local
gas distributor or the authority having jurisdiction
for proper rating methods. If the installer must
convert the unit to adjust for varying altitudes,
the information sticker must be filled out by the
installer and adhered to the appliance at the time
of the conversion. See Figure 6.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Derating procedure
AIR SHUTTER ADJUSTMENT/FLAME
APPEARANCE:
1.To derate this unit, install the appropriate ori-
fice per the High Altitude chart.
THE ALLAGASH B-VENT GAS STOVE IS
SHIPPED FROM THE FACTORY EQUIPPED
AS A NATURAL GAS STOVE; THERE-
FORE, IT WILL BE NECESSARY WHEN
USING THE STOVEWITH PROPANE GAS
TO ADJUST THE AIR SHUTTER ON THE
BURNER TUBE TO ACHIEVE THE PROPER
GAS TO AIR MIX. See Figure 6.
ORIFICE
SIZE
JØTUL
PART #
GAS TYPE
ELEVATION
NATURAL
GAS
0-2000'
(0-610m)
3/32
#54
#42
#55
129114
PROPANE
GAS
0-2000'
(0-610m)
3096145
NATURAL
GAS
2001'-4500'
(611-1170m)
154376
kit
The air shutter adjustment can also help achieve
the desired flame appearance. Generally, flame
appearance is a matter of preference, however
most consumers enjoy the warm yellowish flame.
PROPANE
GAS
2001'-4500'
(611-1170m)
750305P
kit
2.Remove the two ¼” hex head screws that hold
the burner tube/log support to the bottom of
the stove.
Closing the air shutter - will generate very long
yellow flames resulting in soot. Sooting produces
black deposits on the logs, on the inside walls of
the appliance, and potentially on the exterior
termination cap.
3.Remove the burner tube/log support to expose
the main burner orifice.
4.Remove the orifice and replace with the
appropriate one from the high altitude kit.
Sooting is caused by incomplete combustion in
the flames and lack of combustion air entering
the air shutter opening.
5.Be sure to attach the high altitude conversion
sticker provided with the kit to the rating plate
on the appliance.
Opening the air shutter - will generate a flame
that is blue and transparent, or an “anemic”
flame. This flame is generally more efficient but
not as pretty.
6. It may be necessary to adjust the air shutter
on the burner tube. See the AIR SHUTTER/
FLAME APPEARANCE section of this
manual for more details.
Jøtul recommends the following settings for the
Allagash B-Vent gas stove:
for use with propane 1/4” open
for use with natural 1/4” open
This sticker (shown below) is included in all high
altitude kits and must be adhered to the stove
whenever it is converted for high altitude
installations.
AIR SHUTTER
Figure 7
BURNER TUBE
ATTENTION: Air shutter should never be
LESS than 1/8” open.
REMEMBER: Run the stove for a minimum of
15 to 20 minutes for an accurate representation
of the flame appearance- this should be done
before and between any air shutter adjustment.
Figure 6
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust the air shutter
1.Remove the burner tube and using a phillips
head screwdriver loosen the screw at the air
shutter and adjust accordingly.
2.Be sure to retighten the screw that holds the
air shutter setting.
3.Reassemble the stove and close the door,
allow stove to burn 30 minutes on the HIGH
setting, observing the flame continuously.
4.If the flame appears weak, slow, or sooty,
repeat the process described above until the
flame is as desired.
Figure 8
WARNING:
INSTALLING
DECORATIVE
PIPE
AIR SHUTTER ADJUSTMENTS
SHOULD ONLY BE PERFORMED BY A
QUALIFIED PROFESSIONAL SERVICE
TECHNICIAN.
BRACKETS: (The use of decorative pipe is
optional and not included with the Allagash B-
Vent stove.)
To install the decorative pipe brackets on the
Allagash simply remove the four 1/4” hex head
screws holding the 4” flue collar on the stove.
See Figure 9.
INSTALLING THE LOG SET:
It is not neccessary to remove the flue collar.
Place the “L” shaped decorative pipe brackets
on the flue collar and align the holes on the
brackets, flue collar, and draft hood and secure
all three with the four 1/4” hex head screws.
The Allagash is equipped with a one piece log set
and is packaged in bubble wrap inside the firebox.
The log set must be removed from the packaging
and arranged in the unit prior to start up of the
gas stove. Do not handle the log set with your
bare hands. Always wear gloves to prevent skin
irritation from the ceramic fibers.
Black or enamel stove pipe can now rest on the
the draft hood of the appliance while the brackets
center the stove pipe over the draft hood.
To install the log set, remove the packaging and
place the log set inside the firebox, centered from
left to right and completely against the rear wall
of the stove. See Figure 8.
Reminder: single wall stove pipe can never be
used as the vent pipe on the Allagash B-Vent
stove.
Embers: the stove is shipped with a package of
glowing embers. These embers should be “pea
size” and individually spaced across the burner
tube screen. It is best to equally space these
embers for optimum flame appearance. NOTE:
YOU DO NOT HAVE TO USE ALL OF THE
EMBERS.
THE CERAMIC FIBER LOGS AND
GLOWING EMBERS CAN IRRITATE YOUR
SKIN. IF THIS HAPPENS, GENTLY WASH
HANDS WITH WARM SOAPY WATER.
Figure 9
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the blower wiring harness:
INSTALLING THE OPTIONAL
BLOWER:
1. Lift off the stove top plate.
2. Loosen (BUT DO NOT REMOVE) the 10mm bolt
holding the switch box to the side of the stove
(left rear corner of the stove), and lift out the
switch box.
3. Remove the “blank” switch from the box.
(Hint: break the retaining tabs holding the
switch in the box.)
IMPORTANT: IF THE OPTIONAL FORCED AIR
BLOWER KIT (part # 129161) IS TO BE INSTALLED
ON THE STOVE AT THE TIME OF THE
INSTALLATION OR IN THE FUTURE, THE GAS
SUPPLY LINE SHOULD BE INSTALLED AS
CLOSE TO THE FLOOR AS POSSIBLE. USE OF A
90° ELBOW DIRECTLY OFF THE VALVE WILL
ALLOW FOR PROPER CLEARANCE FOR THE
BLOWER.
4. Insert the new HI/OFF/LO switch into the
box.
5. Connect the insulated wires from the blower
to three leads on the HI/OFF/LO switch.
BLACK wire to the HI position, WHITE
wire to the OFF position, and the RED wire
to the LO position. See Figure 11.
6. Retighten the switch box to the side of the
stove. Be sure all wires are unobstructed.
7. Replace top plate.
Mounting the blower:
1. Locate the reflector sheild (28) on the back of
the stove. Remove the cover plate from the
reflector shield to allow the blower bracket to
slide under the stove.
2. Locate the two raised bosses on the bottom plate
(back) of the stove.
3. The blower is mounted to the stove using these
two threaded holes.
REMINDER:
The blower will ONLY come on when the
switch is in the Hi or Lo position and ONLY
when the sensor (thermodisc) is heated by the
stove.
(Approximately 10 - 20 minutes after the stove
has been running).
4. With the blower bracket and sensor facing upward
alignthetwomiddlemountingholesonthebracket
with the two threaded holes on the bottom of the
stove. See Figure 10.
5. Use the two 6mm bolts to attach the blower to
the stove.
6. Be sure to tighten the bolts so that the blower is
drawn upward and tight against the stove bottom.
7. The heat sensor (thermodisc), that is already
attached to the blower bracket, should be inserted
under the stove bottom and make contact with
the firebox! See Figure 10.
Sensor
(thermodisc)
Middle mounting holes.
Use these holes to mount
blower.
Direction
under the
stove.
Figure 11
Figure 10
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SPILL SWITCH:
INSTALLING THE OPTIONAL
WALL THERMOSTAT OR REMOTE:
The Allagash B-Vent gas stove is equipped with a
vent “SPILL SWITCH”. This switch stops gas flow
to the main burner in the event that the appliance
is not vented or if the venting is blocked.
When installing a wall mounted thermostat to
the Allagash, it must be a 750 millivolt DC two-
wire circut thermostat. The thermostat should
be placed in the same room as the heater, typically
5’ off the floor. Avoid drafty areas or any area
that may effect the accuracy of the thermostat.
The thermostat should be connected to the
Allagash using a minimum of 16 gauge wire with
a maximum length of 35 feet of wire.
The spill switch is an important safety device
located on the draft hood of the appliance and is
wired directly to the thermocouple (power source
for the stove). The “spill switch” is a bimetal
sensor that is heat sensitive. In the event that
the venting is not carrying the exhaust up and
out, the heat from the exhaust will trigger the
switch and stop the electrical current to the valve;
thereby stopping gas flow to the main burner.
Connect the two thermostat wire leads to the two
lower terminals on the terminal block located
directly above the ignitor button. Do not
overtighten the connections. IT IS NOT
NECESSARY TO DISCONNNECT ANY
OTHER WIRES. See Figure 12.
Spillage: Condition of flue gases failing to exit
the venting system properly and instead flowing
out of the relief opening of the draft hood and
into the dwelling. Condition calls for
immediate examination of the appliance and
For the thermostat to work the On/Off/T-Stat
switch on the back of the stove must be in the
T-stat position, and the pilot light must be running,
as it is the power source for the thermostat.
venting system and corrective action.
Source: HEARTH- Gas Training Manual
Spillage usually occurs due to incorrct vent size,
or incorrct installation. Be sure to read all of the
installation requirements addressed in this manual
for the proper and safe installation of your
Allagash B-Vent gas stove.
Unexplained outages can be the result of the “spill
switch”. If you experience unexplained outages,
contact your local Jøtul dealer for assistance.
ANY SERVICE TO THE SAFETY SPILL SWITCH
MUST BE DONE BY A QUALIFIED SERVICE
AGENCY.
Figure 12
CAUTION:
LABEL ALL WIRES PRIOR TO DISCONNECTION
WHEN SERVICING THE CONTROLS. WIRING
ERRORS CAN CAUSE IMPROPER AND
DANGEROUS OPERATION. ALWAYS VERIFY
PROPER OPERATION AFTER SERVICING THE
APPLIANCE.
At the thermostat, the two wires should be
connected to the two connections screws on the
thermostat base plate per the manufacturer’s
instructions.
Remote: When using a remote, the remote
receiver should be wired to the terminal block
the same way the thermostat would be. See the
instructions above.
ATTENTION:
AU
MOMENT
DE
L’ENTRETIENDES
COMMANDES, ETIQUETEZ TOUS LES FILS
AVANT LE DEBRANCHEMENT. DES ERREURS
DE CABLAGE PEUVENT ENTRAIUN
FONCTIONNEMENT
DAGEREUX.
INADEQUAT
ET
17
Download from Www.Somanuals.com. All Manuals Search And Download.
NO SMOKE OR SOOT SHOULD BE
PRESENT. CHECK LOG PLACEMENT IF
ANY SOOT OR SMOKE IS DETECTED. IF
SOOT OR SMOKE PERSIST, THE AIR
SHUTTER MAY NEED TO BE ADJUSTED.
CHECKING THE SYSTEM:
1. PURGING THE GAS LINE: When lighting
the appliance for the first time it will take a few
moments to clear the gas line of air. Once this
purge is complete, the appliance will operate as
described in the lighting instructions located on
the stove’s rating plate and the back cover of this
manual. All subsequent lightings of the stove
will not require such purging of the gas line.
See Air Shutter/Flame Appearance section of this
manual for proper air shutter settings and
adjustments (page 14). Note: the more offsets
on the vent system, the greater the need for an
air shutter adjustment.
2. PILOT FLAME: The pilot flame should be
steady, not lifting or floating. The flame should
be blue in color around the pilot hood, with traces
of yellow toward the outer edges.
CAUTION:
DO NOT ATTEMPT TO ALTER THE
FLAME APPEARANCE BY
POSITIONING THE GAS VALVE IN
ANY OTHER POSITION OTHER
THAN THE FULL “ON” POSITION.
It is imperative that the pilot flame engulf the
top 3/8” of the thermopile (power generator) and
the top 1/8” of the quick drop out thermocouple.
The pilot flame should project out of the pilot
hood 1” at all three ports. See Figure 13.
1”
(25mm)
Pilot Hood
Ignitor
3”- 4”
5”-6”
3/8”
(8mm)
Min.
1/8”
(3mm)
Min.
3”- 4”
Thermopile
Thermocouple
Figure 14
Flame appearance on the high setting after
approximately 15 to 20 minutes burning.
Figure 13.
3. BURNER ADJUSTMENT: The Jøtul
Allagash gas stove is equipped with a variable
gas control valve. This valve provides easy
adjustment of the flame height appearance and
heat output. To adjust the flame between the HI
and LO setting, rotate the HI/LO knob, located
in the center of the valve face. Flame height will
adjust approximately 1.0” to 1.5” between the
HI and LO settings. See Figure 14.
Air Inlet Shutter
Pilot Assembly
Burner Tube
WARNING:
AIR SHUTTER ADJUSTMENTS
SHOULD ONLY BE PERFORMED BY A
QUALIFIED PROFESSIONAL SERVICE
TECHNICIAN.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Clean the glass only when necessary. Wipe
surface with a clean, dampened, soft cloth.
Follow with a dry, soft towel as desired.
Take care not to scratch the glass surface.
OPERATION OF APPLIANCE:
1. The Allagash B-Vent gas stove is equipped
with an On/Off/T-stat rocker switch or can
be controlled using an optional wall-
mounted thermostat. A separate switch is
provided for the optional forced air blower
kit.
WARNING:
DO NOT USE ABRASIVE CLEANERS ON THE
GLASS. NEVER CLEAN THE GLASS WHEN IT
IS HOT.
2. When lit for the first time, the Allagash will
emit an odor for several hours. This odor is
MAINTENANCE:
the burn-off by-products of internal paints The Allagash B-Vent gas stove and its venting
and lubricants used in the manufacturing system should be inspected before use and at least
process.
annually by a qualified service technician.
IMPORTANT:
3. Condensation may occur on the glass upon
each lighting of the appliance. This “fog”
will disappear as the appliance heats up.
ALWAYS TURN OFF THE GAS SUPPLY TO THE
STOVE AND UNPLUG THE OPTIONAL FORCED
AIR BLOWER KIT IF INSTALLED, BEFORE ANY
SERVICE WORK IS PERFORMED ON THE
STOVE.
4. Keep the controls and the area under the
appliance free of debris, vacuum this area
frequently. Always keep the appliance area
clear and free from combustible materials,
gasoline and other flammable liquids.
General cleaning: The firebox should be
vacuumed out annually to remove any surface
build up. Be sure to vacuum or wipe off the pilot
assembly and burner orifice and burner tube. Also,
when vacuuming the log set, be sure to handle it
carefully as it is very fragile.
If and when a vacuum is used on any service
for the stove, ALWAYS be sure the stove is
cold and there are NO hot embers or sparks.
Gasket inspection: It is important that the glass
gasket be inspected at least annually. Examine
the rope gasket for signs of deterioration and make
sure the gasket has a positive seal. This is
important to prevent combustion gases from
escaping into the room. Replace the gasket if
necessary, refer to the replacement parts list on
page 21.
5. Remember, this appliance has a continuous
burning pilot flame. Exercise caution when
using products with combustible vapors.
6. CAUTION: DO NOT OPERATE THIS
APPLIANCE WITH THE GLASS
REMOVED CRACKED OR BROKEN.
REPLACEMENT OF THE GLASS
SHOULD BE DONE BY A LICENSED OR
QUALIFIED SERVICE PERSON. USE
To remove the glass panel or glass gasket:
1. Lift off the stove top.
ONLY
REPLACEMENT
GLASS
PROVIDED BY YOUR AUTHORIZED
JØTUL DEALER. NEVER USE ANY
SUBSTITUTE MATERIALS.
2. Release the glass clips atop the firebox.
3. Pull the glass frame assembly straight up and out
of the stove.
4. Lay the asssembly on a flat surface and lift the
metal tabs that secure the glass panel to the frame.
5. Install the new glass panel and gasket in the glass
frame and secure with metal tabs. Do not over
tighten tabs as this could break the glass.
WARNING:
OBSERVE CAUTION NEAR THE DOOR. THE
GLASS PANEL MAY SHATTER UNEXPECTEDLY
IF STRUCK WITH AN OBJECT. ALWAYS
HANDLE THEGLASSPANELWITHCARE. WHEN
SERVICING THE STOVE ALWAYS PULL THE
GLASS ASSEMBLY STRAIGHT UP FOR
REMOVAL.
ALWAYS USE JØTUL AUTHORIZED PARTS.
NEVER USE ANY SUBSTITUE PARTS.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Always replace any damaged or broken parts on
the Allagash with JØTUL AUTHORIZED
PARTS ONLY. These are available through your
Autorized Jøtul dealer. Never use any substitute
parts on your Allagash B-Vent gas stove.
SERVICE LOG:
First Year
Name of Technician__________________
Company Name______________________
Date of service_______________________
Work Performed______________________
__________________________________
The Allagash and its venting system should be
inspected annually or semi-annually by a qualified
service person or agency.
With proper care and maintenance, your appliance
will provide you with years of enjoyment. If you
experience any problem or inconsistency with
your Jøtul Allagash B-Vent gas stove, contact your
authorized Jøtul dealer for assistance.
To expedite the proper service for your appliance
the following information will help your dealer
determine what you will need for parts and service.
SERVICE LOG:
Two Year
RETAIN THIS MANUAL FOR REFERENCE
AND MAKE IT AVAILABLE TO ANYONE
USING OR SERVICING THE STOVE.
Name of Technician__________________
Company Name_____________________
Date of service______________________
Work Performed_____________________
____________________________________
MODEL NAME: Allagash B-Vent Stove
SERIAL NUMBER:__________________________
DATE OF PURCHASE:_______________________
AUTHORIZED DEALER:_____________________
NAME OF INSTALLER:______________________
TYPE OF FUEL:_____________________________
WAS STOVE CONVERTED?___________________
NOTES:
SERVICE LOG:
Third Year
Name of Technician___________________
Company Name______________________
Date of service_______________________
Work Performed______________________
___________________________________
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ALLAGASH B-VENT PARTS LIST
Cast Iron Parts / Enamel Colors
PART
MATTE
BLU/BLK
IVORY
GREEN
INDIGO
10390336
10390436
10390136
103128
1
2
3
4
5
6
7
Left Door
Right Door
Front Panel
Side Panel
Top
10390392 10390327 10390329 10390332
10390492 10390427 10390429 10390432
10390192 10390127 10390129 10390132
102967
102033
102246
10203232
10390292 10390227 10390229 10390232 10390236
Bottom Plate 10390092 10390027 10390029 10390032
10390036
103123
Legs Single
Short Leg Set 350074
Top Cover
10192592 101966
102251
350117
10192532
35007432 35007465
350075
*
10406592 10406527 10406529 10406532 10406536
9
Door Pins
125960
129135
154337
129113
129124 (6ft.)
129122
129121
129123
129132
129320
129109
129310
129180
129149
129313
129186
*
ON/OFFSwitch Only
Reflector Shield
Valance
129153
129175
129106
154319
154346 NG
129128
129152
129471
129116
129472
129473
129446
129447
3094527
129173
129114
3096145
3902573
3902576
154915
154916
129129
10
11
*
Glass Clips
28
29
*
Glass Assembly
Glass Panel only
Gasket only (7/16 tadpole)
Log Set
Wiring Harness -On/Off Switch
Spud Plate Assembly
Orifice Holder
*
30
*
12
13
*
Burner Tube
*
Jam Nut for holder
Pilot Assembly NG
Gasket Pilot assembly
Pilot Orifice NG
Pilot Orifice LP
Embers
*
14
15
16
17
18
*
Log Support
*
Air Divider
*
Air Deflector
*
Exhaust Baffle
Firebox
*
Pilot Line
*
*
Thermocouple
Latch Keeper
Heat Exchanger Gasket
Heat Exchanger
Thermopile
19
20
*
Electrode with wire
Burner Orifice- NG 3/32
Burner Orifice- LPG #54
Ignitor Button
*
*
21
22
23
24
25
26
*
*
*
*
Draft Hood, Lower
Draft Hood, Upper
Flue Starter Collar
Cover Plate Draft Hood
Rear Shroud
129184
129185
129189
129183
129179
129449
154350
154389
154374
129157
129148
*
*
Ignitor Bracket
*
B-Vent Valve NG
B-Vent Valve LP
Brass Elbow
*
Spill Switch
*
Wiring Harness -Spill Switch
Spill Switch Wire - 32 in.
Spill Switch Wire - 35 in.
Wire Tie
*
Main Gas Line (complete) 154372
Terminal Block 129154
*
* not illustrated
27
Box, On/Off/T-stat
Hardware
Accessories
Leg Bolts (m6x20)
117117
120004
117117
117117
120004
120004
117910
117130
117130
117917
117588
Conversion Kit to NG
Conversion Kit to LP
Wall Thermostat
Blower Kit w/Rheostat
Remote
154375
154348
750003
129161
750002
129174
750304
Washer for Leg Bolts
Bolt- Side Wall to Front (m6x20)
Bolt- Front to Base (m6x20)
Washer- Side to Front
Washer- Firebox to Base
Nut- Firebox to Base
Side Clips Bolts (m6x12)
Door Clip Bolts (m6x12)
Valance Screws (#10x1/2)
Door Washers
Screen
Floor Bracket Kit
Only use replacement parts from an Authorized Jotul Dealer.
For the name of the dealer nearest you, call 207 797-5912
or write to:
Jotul North America
400 Riverside Street
Portland, ME 04104
21
Download from Www.Somanuals.com. All Manuals Search And Download.
GF3 BV Allagash Illustrated Parts Breakdown
23
22
20
24
21
5
4
19
26
27
25
18
17
4
16
28
15
10
14
6
3
9
13
12
11
30
2
1
29
7
22
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTING INSTRUCTIONS
FOR YOUR SAFETY, READ BEFORE LIGHTING.
WARNING:
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY
RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.
A. This appliance has a pilot which must be lit
by hand. When lighting the pilot, follow these
instructions exactly.
B. BEFORE LIGHTING, smell all around the
appliance area for gas. Be sure to smell next
to the floor because some gas is heavier than
air and will settle to the floor.
• If your gas supplier cannot be reached, call the
fire department.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it.
Call a qualified technician. Force or attempted
repair may result in a fire or explosion.
WHAT TO DO IF YOU SMELL GAS:
• Extinguish any open flame.
• Open windows.
D. Do not use this appliance if any part has been
under water. Immediately call a qualified service
technician to inspect the appliance and to
replace any part of the control system and any
gas control which has been under water.
• Do not light any appliance.
• Do not touch any electrical switches.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone.
LIGHTING INSTRUCTIONS
1. STOP!Readthesafetyinformationabove.
2. Access the lower controls.
3. Turn the stove ON/OFF switch to “OFF”, or set the
thermostat to lowest setting (if used).
4. Confirm that the gas supply line shut-off valve is open.
5. Push in gas control knob slightly and turn clockwise
to “OFF”.
8. Push in control knob all the way and hold in.
Immediately light the pilot by triggering the spark
ignitor (push the red button repeatedly) until pilot
lights. Continue to hold the control knob in for
about one minute after the pilot lights. Release
knob and it should spring back. The pilot should
remain lit. If it goes out, repeat Steps 5 through 8.
• If knob does not
NOTE:Knobcannotbeturnedfrom“PILOT”to“OFF”
unless the knob is pushed in slightly. Do not force.
return when released,
stop and immediately
Control
Knob
call your service
technician or gas
supplier.
• If pilot will not stay
lit after several tries,
PILOT ASSEMBLY
turn the control knob
to OFF and call your service technician or gas
supplier.
9. Turn gas control knob counterclockwise
to “ON”.
10.Turn the stove ON/OFF switch to “ON”, or set
thermostat (if used) to desired temperature.
CONTROL VALVE
6. Wait five (5) minutes to clear out any gas. If you then
smell gas, STOP! Follow “B” in the safety information
above on this page. If you do not smell gas, go to the
next step.
7. Push in gas control knob slightly and turn counter-
clockwise
to“PILOT”.
TO TURN OFF GAS TO THE APPLIANCE:
1. Turn ON/OFF switch to” OFF”. The pilot will remain lit for
normalservice.
2. For complete shutdown, turn ON/OFF switch to “OFF”.
3. Access the lower controls.
4. Depress gas control knob slightly and turn clock-
wise
to “OFF”. Do not force.
Download from Www.Somanuals.com. All Manuals Search And Download.
Stoves and fireplaces must be installed to conform to local and national building regulations. Before preparing for the installation of
the appliance, it is important that the instructions issued with the unit are carefully read an strictly adhered to. Jøtul pursues a policy
of constant product development. Products supplied may therefore differ in specification, color and type of accessories for those
illustrated and described in the brochure.
Jøtul vise sans cesse a ameliorer ses produits. C’est pourquoi, il se reserve le droit de modifier les specifications, couleurs etequipement
sans avis prelable.
Jøtul ASA
P.O. Box 1411
N-1602 Fredrikstad, Norway
Jøtul North America
400 Riverside Street
Portland, ME 04104
December 2000.4
129450
Download from Www.Somanuals.com. All Manuals Search And Download.
|