Jøtul F 3 USA
Installation and Operating Instructions for the USA and Canada
Kindly save these instructions for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Installation and Operation Instructions for USA/Canada
Installation et fonctionnement pour Canada
Safety notice: If this solid fuel room heater is not properly installed, a house fire may result.
For your safety, follow the installation directions. Contact local building or fire officials about
restrictions and installation inspection requirements in your area. Save these instructions for
future reference.
Avis de sécurité:Une installation non appropriée de ce poêle de chauffage risque de provoquer
un incendie. Assurez votre sécurité en respectant les directives d’installation suivantes.
Consultez les autorités locales du bâtiment ou de la prévention des incendies au sujet des
restrictions et exigences relatives aux inspections d’installations dans votre région.
Tested and listed by ITS, Intertek Testing Services, Middleton, Wisconsin.
Tested to U.S. Standards: ANSI/UL 737 andANSI/UL 1482, Canadian Standards: CAN/ULC-S627-M93
Standards
Check Building Codes
The Jøtul F 3 woodstove has been tested and listed to:
U.S. Standards: ANSI/UL 737 and ANSI/UL 1482
Canada:CAN/ULC-S627-M93
When installing, operating and maintaining your Jøtul F
3 woodstove, follow the guidelines presented in these
instructions, and make them available to anyone using
or servicing the stove.
Tests performed by:
Your city, town, county or province may require a building
permit to install a solid fuel burning appliance.
ITS, Intertek Testing Services, Middleton, WI
Manufactured by:
In the U.S., the National Fire Protection Association’s
Code, NFPA 211, Standards for Chimneys, Fireplaces, Vents
and Solid Fuel Burning Appliances,or similar regulations,
may apply to the installation of a solid fuel burning
appliance in your area.
Jøtul AS., P.O. Box 1411, Fredrikstad, Norway
Distributed by: Jøtul North America, P.O. Box 1157
400 Riverside Street, Portland, ME 04104
This heater meets the U.S. Environment Protection
Agency’s Emissions limits for wood heaters
manufactured and sold after July 1, 1990.
In Canada, the guideline is established by the CSA
Standard,CAN/CSA-B365-M93, Installation Code for Solid-
Fuel-Burning Appliances and Equipment.
Under specific test conditions,this heater has shown heat
output at rates ranging from 11,500 to 43,500 BTU’s per
hour.
Always consult your local building inspector or authority
having jurisdiction to determine what regulations apply
in your area.
The Jøtul F 3 woodstove is only listed to burn wood. Do
not burn any other fuels.
Read this entire manual before you install and use your
new room heater.
Save these instructions and make them available to
anyone using or servicing the stove.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Notices
Reminder:
•
Be sure to read this entire manual before you install
Your local officials have final authority in determining if
a proposed installation is acceptable. Any requirement,
that is requested by the local authority having jurisdiction,
that is not specifically addressed in this manual, defaults
to NFPA 211, and local codes.
or use your new Jøtul F 3.
•
If this room heater is not properly installed, a house
fire may result. To reduce the risk of fire, follow the
installation instructions. Failure to follow these
instructions may result in property damage, bodily
injury, or even death.
In the U.S. or in Canada,CAN/CSA-B365-M and local codes.
Installing the venting
•
•
•
Jøtul recommends that you have your new Jøtul F 3
installed by a professional installer of solid fuel
burning appliances.
The Jøtul F 3 can be vented from the top, the rear or
from either the right or left side. Follow the instructions
below for the desired venting location.
Extremely hot while in operation! Keep children,
clothing and furniture away. Contact may cause skin
burns.
Top exit venting
When top exit venting is desired,use a 3mm allen wrench
to remove the two set screws that secure the top casting
to the sides of the stove and lift off the top casting. Lay
the top casting on a flat surface upside down and remove
the 10mm bolt from the traverse bar and remove the
smoke outlet cover.
Avoid creating a low pressure condition in the room
where the stove is operating. Operating an exhaust
fan or a clothes dryer could create a low pressure area,
causing poisonous gases to come out of the stove into
the room.
You can prevent low pressure conditions by providing
adequate combustion air within 24” but not closer
than 12”from the stove. Or,simply install the optional
outside air manifold system, which allows the direct
connection of air from outside the house to the stove.
Reinstall the top casting, be sure to secure with the two
set screws that were removed. See figure 1.
Fig. 1
Stove pipe stop
Upside down
•
•
Do not use chemicals or fluids to start the fire. Some
fuels will, during combustion, separate carbon
monoxide and generate it in the burn chamber.
Carbon monoxide is toxic, so please follow the
guidelines in this manual for proper operation of your
Jøtul F 3.
Top casting
If you for some reason experience smoke “roll-out”
from the stove, it may activate smoke detectors if
installed in the house.
Traverse bar securing
Stove pipe top
smoke outlet cover to top
casting
Do not connect this stove to any air distribution duct or
system.
Rear exit venting
When rear exit venting is desired it will be necessary to
“knock-out” the vent hole from the rear casting.
Installation
Remove the top casting of the stove by removing the two
3mm set screws that secures the top to the sides. The
set screws are located on the outside of the stove on the
top of each side panel.
If this solid fuel room heater is not properly installed a
house fire may result. For your safety, follow the
installation directions. Contact the local building or fire
officials about restrictions and installation inspection
requirements in your area.
Using a 10mm wrench remove the double rear
heatshields from the back of the stove.Remove the front
door to avoid damage to the glass. Reminder:Loss of the
door washer will result in improper door alignment when
reinstalling the door.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Insert the end of the adapter with the four holes into
the stove. These holes allow the adaptor to be attached
to the stove’s internal collar, using the nuts and bolts
provided with the stove. See figure 3.
Using a claw hammer or a small sledge hammer strike
the center of the 6”“knock-out”disc from the outside of
the stove. The “knock-out” disc will break into four
wedges and may need to be tapped out. Touch up any
remaining sharp edges with a file or hand grinder.
Fig. 3
Direction into the
Note: The ivory Jøtul F 3 ’s are rear vented from the
factory. It is not necessary to“knock-out”the rear casting
of the stove. However, if top exit is desired it is necessary
to install a smoke outlet cover on the rear outlet of the
stove.
stove
Reinstall the top casting and front door, remembering
the washer. The two rear heatshields must be reinstalled
on the stove. Remove the metal cover plates from the
heatshields and reinstall. Reminder: There is a small nut
used as a spacer between the two heatshields. See fig. 2.
The adaptor should be inserted into the stove until the
bead on the adapter is flush with the top, back or side
casting. Now the adaptor is ready to accept single or
double walled stove pipe. See figure 4.
Fig. 2
Each joint of chimney connector or stove pipe must be
secured with at least three sheet metal screws to ensure
that the sections do not separate.
Spacers
Adaptor bead should
be flush with stove
Fig. 4
Heatshield with listing
label should be installed
on the outside
Stove pipe - chimney connector
The chimney connector is a single walled pipe used to
connect the stove to the chimney. For use with the
Jøtul F3 the chimney connector must be 6” in diameter,
with a minimum thickness of 24 gauge black steel.
Side exit venting
If venting through the side is desired it will be necessary
to remove the top casting. Using a 3mm allen wrench
remove the two set screws that secure to the top to the
side panels. Remove the front door to avoid damage to
the glass. Reminder: Loss of the door washer will result
in improper door alignment when reinstalling the door.
Aluminum and galvanized steel pipe is not acceptable
for use with the Jøtul F3. These materials cannot
withstand the extreme temperatures of a wood fire and
can give off toxic fumes when heated.
Each chimney connector or stove pipe section must be
installed to the stove flue collar and to each other with
the male (crimped) end toward the stove. See figure 5.
Using a claw hammer or a small sledge hammer strike
the center of the 6”“knock-out” disc from the inside of
the stove. The “knock-out” disc will break into four
wedges and may need to be tapped out. Touch up any
remaining sharp edges with a file or hand grinder.
Reinstall the front door, remembering the washer and
the top casting.
Fig. 5
Crimped end installed
toward the stove
Installing the stove pipe adapter
After the appropriate flue outlet in the stove has been
established the stove pipe adapter (included with every
stove) must be installed so that standard stove pipe can
be installed onto the stove.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
This prevents any amount of condensed or liquid
creosote from running down the outside of the pipe or
the stove top. All joints, including the flue collar
connection must be secured with three sheet metal
screws to ensure that the sections do not separate.
many local codes differ from the national code to take
into account climate, altitude, or other factors. It is
important that you check with your local building
officials to find out what codes apply in your area before
installing your new Jøtul F3.
For the best performance the chimney connector should
be as short and direct as possible, with no more than
two 90° elbows. The maximum horizontal run is 36”and
a recommended total length of stove pipe should not
exceed 10 feet. Always slope horizontal runs upward ¼”
per foot toward the chimney.
Masonry chimneys
When installing the Jøtul F3 into a masonry chimney you
must conform to all of the following guidelines:
•
The masonry chimney must have a fireclay liner or
equivalent, with a minimum thickness of 5/8” and
must be installed with refractory mortar. There must
be at least 1/2” air space between the flue liner and
chimney wall.
No part of the chimney connector may pass through an
attic or roof space, closet or other concealed space, or
through a floor or ceiling. All sections of the chimney
connectors must be accessible for cleaning. Where
passage through a wall or partition of combustible
construction is desired, the installation must conform
with NFPA 211 or CAN/CSA-B365, and is also addressed in
this manual.
•
The fireclay flue liner must have a nominal size of 8”
x 8”, and should not be larger than 8”x 12”. If a round
fireclay liner is to be used it must have a minimum
inside diameter of 6” and not larger than 8” in
diameter. If a chimney with larger dimensions is to
be used,it should be relined with an appropriate liner
that is code approved.
Do not connect this unit to a chimney flue servicing
another appliance.
Do not use the connector pipe as a chimney.
•
The masonry wall of the chimney, if brick or modular
block, must be a minimum of 4” nominal thickness.
A mountain or rubble stone wall must be at least 12”
thick.
Chimney requirements
There are two types of chimneys suitable for the Jøtul
F3:
•
•
A newly-built chimney must conform to local codes
and in their absence must recognize national
regulations.
1. A code- approved masonry chimney with a flue liner.
2. A prefabricated chimney complying with the
requirements for type HT (2100°F) chimneys per UL
103 or ULC S629.
When using an existing chimney,it must be inspected
by a professional licensed chimney sweep,fire official,
or code officer, to ensure that the chimney is in proper
working order.
The chimney size should not be less than the cross-
sectional area of the flue collar,and not more than three
times greater than the cross-sectional area of the flue
collar.
•
•
No other appliance can be vented into the same flue.
An airtight clean-out door should be located at the
base of the chimney.
When selecting a chimney type and the location for the
ce of the chimney,as well as the proximity of surrounding
trees or buildings.
Prefabricated chimneys
As a result,a short masonry chimney on the exterior of a
house will give the poorest performance. This is because
it can be very difficult to warm the chimney thereby
creating inadequate draft. In extremely cold northern
areas it may be necessary to reline the chimney or extend
its height to help establish draft.
If a prefabricated metal chimney is to be used it must be
a chimney type that is tested and listed for use with solid
fuel burning appliances. High temperature (ht) chimney
standard UL103 for the U.S. And high temperature
standard ULC S-629 for Canada.
Oppositely, a tall masonry chimney inside the house is
easier to keep warm and will perform the best.
The manufacturer’s installation instructions must be
followed precisely. Always maintain the proper clearance
to combustibles as established by the pipe manufacturer.
This clearance is usually a minimum of 2”, although it
may vary by manufacturer or for certain chimney
components.
The following guidelines give the necessary chimney
requirements based on the national code (ANSI-NFPA 211
for the us. And CSA CAN-B365 for Canada). However,
6
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Common method
Chimney height
When passing through a combustible wall to a masonry
chimney this method requires the removal of all
combustible materials from at least 12” around the
chimney connectors proposed location.With a 6” round
liner the minimum area required would be 31” x 31”
square.
Whether a masonry chimney or prefabricated metal
chimney is used it must be the required height above
the roof line.
The requirement is:
The chimney must be at least 3 feet higher than the
highest point where it passes through the roof and at
least 2 feet higher than the highest part of the roof or
structure that is within 10 feet of the chimney,measured
horizontally. See figure 6.
The space is then filled with at least 12”of brick around a
fireclay liner. Remember, the liner must be ASTM C35 or
equivalent, with a minimum wall thickness of 5/8”.
It is important to remember to locate the pass-through
at least 18” from the ceiling for proper clearance to
combustibles.
Fig. 6
It will be necessary to cut wall studs,install headers, and
construct a sill frame to maintain the proper dimensions
and to support the weight of the brick.
The bricks must be solid brick with a minimum of 3 1/2"
thick (4” nominal).
Refractory mortar must be used at the junction of the
chimney and the pass-through liner. The pass-through
liner must not penetrate the chimney liner beyond the
inner surface of the chimney liner. Use extreme care
when constructing the hole in the chimney liner, the tiles
can shatter easily. See figure 7.
Chimneys shorter than 14 feet may not provide adequate
draft. This could result is smoke spilling into the room
from the stove when loading the stove,or when the door
is open. In addition, inadequate draft can cause back
puffing, which is a build up of gases inside the firebox.
Fig. 7
Wood Stud 2”
Clearance to
Chimney
Flue Liner
Header
Other times, chimney height can create excessive draft
which can cause high stove temperatures and short burn
times. Excessive drafts can be corrected by installing a
butterfly damper. If you suspect you have a draft
problem, consult your dealer.
12”
30.5 cm
Pass through
construction:
12” Brick from
thimble to
12”
combustibles
Thimble: 5/8”
Fireclay Liner or
equivalent
Wall pass-throughs
When your installation unavoidably requires the
chimney connector to pass through a combustible wall
to reach the chimney, always consult your local building
officials, and be sure any materials to be used have been
tested and listed for wall pass-throughs.
Sill / Support
In the U.S.
The national fire protection association’s publication,
NFPA 211, standard for chimneys, fireplaces, vents and
solid fuel burning appliances permits four methods for
passing through a combustible wall. Before proceeding
with any method be sure to consult with your local
building officials to discuss any local code requirements.
In Canada
In Canada the standard has been established by the
canadian standard association. The installation must
conform to CAN/CSA-B365,installation code for solid fuel
burning appliances and equipment. Before proceeding
be sure to consult your local building inspector.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Common method
Make sure the connector pipe or thimble sleeve does not
protrude into the flue liner, thereby restricting the area
the smoke has to flow through. This bottle-neck will have
a negative affect on the chimney system.
This method requires the removal of all combustible
materials from at least 18”(457mm) around the chimney
connector’s proposed location. With a 6”round liner the
minimum area required would be 43” x 43” square.
The chimney connector should be sealed at the thimble
with refractory cement and the stove pipe leading to the
stove should have a minimum of three screws.
It is important to remember to locate the pass-through
at least 25” from the ceiling to maintain the proper
clearance to combustibles.
Do not connect this stove to a chimney flue servicing
another appliance of any kind.
The space that is cleared of combustible materials must
then remain empty. Sheet metal panels can then be used
to cover the area. However, when using a panel on both
sides of the wall each cover must be installed on
noncombustible spacers at least 1”from the wall. If one
panel of sheet metal is to be used it may be installed
flush to the wall.
Hearth-mount into a masonry fireplace
The Jøtul F 3 may be installed into a masonry fireplace
provided the opening is a minimum of 28 1/2” high. The
short leg package reduces the stove’s height by 2 1/4”.
When installing the Jøtul F 3 into a masonry fireplace,
code requires that the fireplace damper plate be removed
or securely fixed in the open position. A connector pipe
must then extend from the stove’s flue exit through the
damper area of the fireplace and into the chimney tile
liner. See figure 9.
See section 5.3.1 and 5.3.2 of CAN/CSA - B365-m91.
Consult your local building inspector, authorized Jøtul
Dealer, NFPA 211 in the U.S. or CAN/CSA-B635 in Canada
for other approved wall pass-through methods.
Connecting to the chimney
Fig. 9
Masonry chimney
When installing a Jøtul F 3 into a masonry chimney
through a “thimble”(the opening through the chimney
wall to the flue), the thimble must be lined with ceramic
tile or metal and be securely cemented in place.
Tile liner
The chimney connector/stove pipe must slide completely
inside the thimble to the inner surface or the flue liner.
It may be necessary to make use of a thimble sleeve (a
pipe with a slightly smaller diameter than standard stove
pipe). This special pipe can be easily installed into a
thimble. See
Connector extends to first
flue tile
Figure 8.
Damper opening is sealed
with sheetmetal plate and
sealant
Fig. 8
Connector pipe must
be flush with the
inside of the flue tile
Chimney
Connector
Pipe
Flue Tile
Thimble
The inside area of the flue liner must not be less than
the area of the stove’s flue exit,and cannot be more than
three times greater than the cross sectional area of the
stove’s flue exit.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Clearances to combustibles
If the chimney liner is too large to accommodate the
stove, an approved relining system must be installed to
resize the flue.
Floor protection
Floor protection under the Jøtul F 3, must be one of the
A new sheet metal damper block-off plate must be
installed around the connector pipe at the damper frame
and sealed with the proper sealant (usually high-temp
silicone).
following:
1. Any non combustible material with an insulative
R value of 1.1.
2. Any UL, ULC or WH hearth board or prefrabricated
non-combustible material.
Fireplace installation must also observe the proper
clearances to surrounding trim and mantels (addressed
in clearance section of this manual).In addition,fireplace
installations must also adhere to the floor protection
guidelines specified in the following section.
The bottom heatshield (standard equipment) is required
in all installations.
Individual sections of floor protection must be mortared
together t,o prevent sparks from falling through to
combustible materials. Any carpeting must be removed
from under the floor protection.
Prefabricated chimneys
When installing the Jøtul F 3 to a prefabricated metal
chimney always follow the pipe manufacture’s
instructions and be sure to use the components that are
required. This usually includes some type of“smoke pipe
adapter” that is secured to the bottom section of the
metal chimney and allows the chimney pipe to be
secured to it with three sheet metal screws. See figures
10 and 11.
In the U.S.and Canada
The Jøtul F 3 must be installed on a non-combustible
surface extending a minimum of 16” for U.S. (46 cm for
Canada) in front of the stove and 8” (20 cm) on the
remaining sides of the stove (measured from side and
back panels).
This will result in a minimum floor protection of 39 cm
D x 39 cmW. for U.S.,and 104 cm D x 99 cmW for Canada.
See figure 12.
In a rear vent installation the floor protection must also
extend under the stove pipe a minimum of 2” (5 cm)
beyond either side of the pipe.
Fig. 10
Listed Cap
2”
Fig. 11
Storm Collar
Listed
Fig. 12
(5 cm)
Chimney Attic
Flashing
Insulation
Shield
Specified
A
clearance
A
A
39”U.S.
(104 cm Can)
Combustible
Ceiling Joists
Ceiling
to
Support
Stove
B
Chimney
Connector
39”
(99 cm Can)
Hearth Protection
Floor
Protector
A: 8” (20 cm)
B: 16” for U.S. (46 cm for Canada)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Clearances to walls and ceilings
Wall Shield for close clearance
The following clearances have been tested to UL and ULC
standards and are the minimum clearances specifically
established for the Jøtul F 3. (See next page)
Combustible wall
Wall shield
The following charts and diagrams give the required
clearances you must maintain when installing the
Jøtul F 3 near combustible surfaces.
A combustible surface is anything that can burn (i.e.
Sheet rock,wall paper,wood,fabrics etc.).These surfaces
are not limited to those that are visible and also include
materials that are behind non-combustible materials.
Must be 30” wide and centred behind the stove.
Must be 1” off the wall and 1” off the floor.
With standard legs, the shield must be 32” high.
With optional short legs, the shield must be 30” high.
If you are not sure of the combustible nature of a
material, consult your local fire officials.
Remember: “Fire resistant” materials are considered
combustible; they are difficult to ignite, but will burn.
Also “fire-rated” sheet rock is also considered
combustible.
Combustible wall
Wall shield
The wall shield must
Contact your local building officials about restrictions
and installation requirements in your area.
extend
a
min. of 4”
(102mm) past the side of
the stove.
Using shields to reduce clearances
The wall shield must
extend
a
min. of 4”
Pipe shields:When using listed pipe shields to reduce the
connector clearance to combustibles, it must start 1”
above the lowest exposed point of the connect pipe and
extend vertically a minimum of 25”above the top surface
of the stove.
(102mm) past the ash lip of
the stove.
Must be 1” off the wall and 1” off the floor.
With standard legs, the shield must be 40” high.
With optional short legs, the shield must be 38” high.
Both shields must extend and join in the corner.
Double wall pipe:Listed double wall pipe is an acceptable
alternative to connector pipe heatshields.
Wall-mounted protection: When reducing clearances
through the use of wall mounted protection:
Combustible wall
Wall shield
In the U.S. Refer to NFPA 211, standard for chimneys,
fireplaces, vents and solid fuel burning appliances, for
acceptable materials, proper sizing and construction
guidelines.
The wall shield must
extend a min. of 12” (305
mm) past the side of the
stove.
In Canada, refer to CAN/CSA-B365, installation code for
solid-fuel burning appliances and equipment, also for
acceptable materials, proper sizing and construction
guidelines.
The wall shield must
extend a min. of 12” (305
mm) past the ash lip of the
stove
Stove mounted rear heatshield is standard equipment
on all Jøtul F 3`s. No other stove mounted heat shield
may be used.
Must be 1” off the wall and 1” off the floor.
With standard legs, the shield must be 40” high.
With optional short legs, the shield must be 38” high.
Both shields must extend and join in the corner.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Jøtul F 3 Clearances
Stove Clearances
Top vent/vertical
Unprotected Surfaces
Protected Surfaces
per NFPA 211 or CAN/CSA-B365-M
Side
Rear Corner
Side Rear
Corner
Rear heatshield with
Single wall pipe
24"
25"
18"
10"
14"
10"
610mm 635mm 460mm
255mm 355mm
255mm
Rear heatshield with
18"
10"
14"
6" 6"
6"
Double wall pipe or shields
460mm 255mm 355mm
150mm 150mm
150mm
Stove Clearances
Unprotected Surfaces
Protected Surfaces
Rear Vent/Horizontal
per NFPA 211 or CAN/CSA-B365-M
Side
Rear Corner
Side Rear
Corner
18”
Rear heatshield with
Single wall pipe
24”
25”
20”
10”
25”
610mm 635mm 510mm
255mm 635mm
460mm
Rear heatshield with
18”
14”
17”
6”
6”
6”
Double wall pipe or shields
460mm 355mm 430mm
150mm 150mm
150mm
Connector
Clearances
Unprotected Surface
Protected Surface
per NFPA 211 or CAN/CSA-B365-M
Singlewall pipe -vertical installations
Double wall pipe-vertical installations
Single wall pipe -horizontal installations
18" (460mm)
6" (150mm)
pipe mfgr. listing
18”(460mm)
pipe mfgr. listing
9” (230mm)
Double wall pipe-horizontal installations pipe mfgr. listing
pipe mfgr. listing
Very important:
Top vent/vertical- assumes the connector pipe is exiting
off the top of the stove and traveling vertically. If top vented
to any horizontal runs –the stove’s position is dictated by
the connector pipe clearances.
Rear vent/horizontal- assumes the connector pipe is
existing out the rear of the stove and is traveling
horizontally to the chimney. If rear vented to vertical run –
the stove position is dictated by the connector pipe
clearances.
Dimensions in Inches represent U.S. requirements.
Dimensions in Millimeters represent Canadian
requirements.
A: Top to Mantel
B: Top to Top Trim
34”
20”
860 mm
510 mm
330 mm
610 mm
C: Side to Side trim 13”
D: Side to Side Wall 24”
Wall protection is discussed in further detail on page
10 of this manual.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Minimum protected alcove:
Notice
Assumes-
Accessories for woodstoves for clearance reduction have
been developed by many manufacturers.If not following
the methods of the installation codes, be sure that any
accessory you choose has been tested by an independent
laboratory and carries the laboratory’s testing mark.
Make sure to follow all of the manufacturer’s
instructions.
Top exit, double wall pipe, and stove’s rear heatshield.
Minimum alcove width =
Maximum alcove depth=
35” (890mm)
24” (610mm)
Height above the top of the stove= 40” (1015mm)
In a protected alcove installation both side walls and rear
wall must be protected per NFPA 211 or CAN/CSA-B365.
The wall protection must be elevated 1” from the floor
and at least 1” off the combustible wall to allow for an
air-flow.
Always contact your local building inspector or fire
officials about restriction and requirements in your area.
Reminder,it is the local officials who have final authority
in the installations approval.
Fig. 14
Alcove
The Jøtul F 3 is approved for installations in an
unprotected and protected alcove provided the
following guidelines are followed: Stoves must be
positioned as shown in figures 13 or 14.
Alcove floor protection must be:A UL/ULC or WHI listed
hearth board or a non combustible material with a
minimum r value of 1.1.
Minimum unprotected alcove:
Assumes-
Top exit, single wall pipe, and stove’s rear heatshield.
Rear exit alcove installations:
Minimum alcove width =
Maximum alcove depth =
71” (1805mm)
40” (1015mm)
Unprotected alcove:Assumes single wall pipe and stove’s
rear heatshield.
Height above the top of the stove = 68” (1730mm)
Top vent/vertical - assumes the connector pipe is exiting
off the top of the stove and traveling vertically. If top
vented to any horizontal runs – the stove’s position is
dictated by the connector pipe clearances.
Minimum alcove width =
71” (1805 mm)
40” (1015mm)
68” (1730mm)
Maximum alcove depth =
Alcove ceiling above top of stove =
Protected alcove: Assumes double wall pipe and stove’s
rear heatshield.
Fig. 13
Minimum alcove width =
35” (890mm)
30” (760mm)
40” (1015mm)
Maximum alcove depth =
Alcove ceiling above top of stove =
Warning:
Do not install in a bedroom/sleeping room. The structural
integrity of the mobile home’s floor, wall, ceiling/roof
must be maintained.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
When first starting a fire: The primary control lever
should be at the far right position, and the start-up air
lever should be in the far right position. This will allow
for the maximum amount of air to enter the stove and
assist in starting the fire quickly and most effectively.
Operation
Before building a fire in your new Jøtul F 3, please read
the following section carefully and completely.
Do not burn
Once the fire is established the start-up air lever should
be closed and the primary air lever should be adjusted
according to the amount of heat desired.
First this stove is designed to burn natural wood only,
wood that has been air-dried for a period of 6 to 14
months will provide the cleanest most efficient heat.
Remember: The more air entering the stove the hotter
the fire the shorter the burn time. Moving the primary
air lever to the left reduces the air-flow into the stove
which prolongs the fire at a lower heat output.See figure
15.
Do not burn:
*Coal
*treated or painted wood
*Garbage
*chemical chimney cleaners
*Cardboard *colored paper
*Solvents
*any synthetic fuel or logs
Breaking in your new stove
The burning of any of these materials can result in the
release of toxic fumes. Never use gasoline,gasoline-type
lantern fuel, kerosene, charcoal lighter fluid, or similar
liquids to start or“freshen-up”the fire. Always keep such
liquids away from the heater at all times.
Your new Jøtul F 3 is constructed of cast iron and stove
furnace cement. This type of construction requires the
stove to be“broken-in”gradually so that heat expansion
does not occur too quickly and cause damage.
Important
To monitor the stove’s temperature, Jøtul recommends
the use of a magnetic stove-top thermometer, placed
directly on the corner of the stove’s top plate.
Never build or allow the fire to rest directly on the glass.
The logs should always be spaced at least one inch from
the glass to allow for proper air flow within the stove.
Complete the following steps for the proper break-in
procedure for the Jøtul F 3:
Controls on the Jøtul F 3
1. Light a small fire, newspaper and kindling only, only
allow the stove to reach a maximum surface
temperature of 200°. Burn for approximately 1 hour.
2. Allow stove to cool to room temperature.
3. Light a second fire, allowing the stove to reach a
maximum temperature of 300° for 1 hour.
There are two air controls on the Jøtul F 3.
The primary air control lever (A) is located on the front
of the stove in the top right corner. The primary air lever
controls the amount of air that enters the stove for
combustion.
4. Cool the stove to room temperature.
5. Light a third fire and gradually allow the stove to
reach a surface temperature of 400°
The start-up air control lever (B) is located below the glass
in the center of the front door. This control is for“start -
up”air only and should not be used to freshen an existing
fire or during refueling. Never leave the stove
unattended while this control is open, overfiring could
result, which can damage the appliance. See figure 15.
6. Cool stove to room temperature. This completes the
“break-in”procedure.
Never allow the stove to exceed a 400° surface
temperature during any “break-in fire” with the
exception of the last “break-in” fire.
A
Fig. 15
Note: It is normal for a new painted stove to emit an
odor and even smoke during its first several fires. This is
caused by the seasoning of the high temperature paint
and will diminish with each fire and will eventually
disappear. Opening a window or door to provide
additional ventilation will reduce the odor as this process
takes its course.
B
13
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Never overfire the stove
Adding fuel
When reloading the stove while it is still hot and a bed
of hot embers still exist,follow this reloading procedure:
If any part of the stove or chimney glows, you are
overfiring, and a house fire or serious damage to the
stove or chimney could result. Immediately close down
the air control if you notice this condition.
•
•
Always wear gloves when tending to the stove.
Push the air control lever to the full open position
(far right).
•
•
Wait a few seconds before opening the door.
Use a stove tool or poker to distribute the hot embers
equally around the firebox.
Starting and maintaining a fire
•
•
•
Load the fuel, usually with smaller logs first.
Close the door, be sure to latch the door tightly.
Wait 5 – 10 minutes before adjusting the primary air
to the desired heat output setting.
Burn only solid wood directly on the bottom grate of the
stove, do not elevate the fire in any way.
The ash pan door on the stove must always be securely
closed when the stove is in operation.
(If you have at least a 2” thick ember bed when
reloading, it may be possible to close the door and
immediately adjust the air control setting).
Burning the stove with the ashpan open will over-fire
the stove and cause interior damage.
The formation of creosote
With the primary air control lever and the start-up air
control lever in the full open position (far right),start with
several sheets of crumbled newspaper placed directly on
the grate. On top of the newspaper,place several pieces
of small dry kindling (approx. 1”in diameter) with two to
three larger logs (approx. 3” to 5”in diameter) on top.
When wood is burned slowly and at low temperatures,
it produces tar and other organic vapors,which combine
with moisture to form creosote. The slow moving smoke
carries the creosote vapors,which condense in the cooler
chimney flues, and this creosote then sticks to the
chimney walls.
Light the fire and close the door, slowly building the fire
by adding larger and larger logs. Close the start-up air
control lever after the fire is established and new fuel
lights easily. Be sure to follow the break-in procedure
before creating a fire that will damage the stove.
The creosote that accumulates in the chimney is highly
flammable and is the fuel of chimney fires. To prevent
chimney fires it is important to have the chimney and
chimney connector pipe inspected and/or cleaned semi-
annually. A qualified chimney sweep or other authorized
service person can provide this service.
Once the stove has reached a surface temperature range
of between 400° and 600°,adjust the primary air control
lever as necessary to generate the heat output and burn
time desired.
It is also important to remember that chimney size,
temperature and height all affect draft which in turn
affects the formation of creosote. Be sure to follow the
installation and operation guidelines established in this
manual.
Jøtul recommends the use of a magnetic stove top
thermometer to monitor the surface temperature of the
stove. The optimum surface temperature range for the
most efficient burn is between 400° and 600°.
See figure 16 below for the optimum locations of a stove-
top thermometer.
Maintenance
Ash removal:Of course, for your protection always wear
Fig. 16
safety gloves when handling the ash pan.
Ash removal will be required periodically depending on
how frequently the stove is used. Conveniently, the
Jøtul F 3 is equipped with an ash pan assembly for easy
ash removal, without the need for opening the front
doors.
The ash pan door is located under the front ashlip of the
stove. To open the ash door rotate the door knob
Stove top thermometer
14
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
counterclockwise to unlatch the door and clockwise to
latch the door.
5. Apply a small bead of gasket/stove cement and the
new gasket. Do not overlap the ends of the gasket
rope.
Remove the ash pan. When the stove is in operation
always close the ash pan door before leaving to dispose
of the ashes.
6. Center the new glass panel over the gasket and
reinstall the glass clips. See figure 17.
Important: The side of the glass treated with an
infrared coating (marked on the perimeter) should
always be facing outward. It is extremely important
to tighten the glass clips slowly and in a repeating
pattern, like tightening the lugs on an automobile
wheel.
The ashes should be placed in a metal container
equipped with a tight sealing lid. The container should
be placed on a noncombustible floor or on the ground,
well away from all combustible materials, pending final
disposal. If the ashes are disposed of by burial in soil or
otherwise locally dispersed, they should be retained in
the closed container until all cinders have thoroughly
cooled.
7. It may be necessary to retighten the glass clips after
the stove has be burned and the gasketing has been
seated.
Fig. 17
Glass
Glass care
Glass clips
Gasket
Door
Cleaning: On occasion it will be necessary to clean the
carbon deposits and fly ash off of the glass. If the carbon
and fly ash are allowed to remain on the glass for an
extended period of time it could eventually cause the
glass to become etched and cloudy. Any creosote,which
might deposit on the glass, will burn off during the next
hot fire.
The proper cleaning procedure is as follows:
1. Glass needs to be completely cool.
2. Only use a cleaner that is specifically designed for this
purpose. The use of abrasives will damage the glass
and ultimately leave the glass frosted.
3. Rinse and dry glass completely, before burning your
stove.
General Maintenance
Like your car, regular maintenance prolongs the life of
your appliance. The following procedures do not take
long and are generally inexpensive, but when done
consistently, increase the life of your appliance and in
turn, increase your years of enjoyment.
Important:
Replace glass only with a ceramic glass panel specifically
designed for the Jøtul F 3. Do not use substitutes.
Replacement glass panels can be ordered through your
Jøtul dealer.
At least once a year you should perform the following
maintenance procedures:
•
Thoroughly clean the stove. Enamel surfaces should
be cleaned with soap and water.
Glass removal: Always operate the doors slowly and
cautiously to avoid cracking or breaking the glass. Never
use the door to push wood into the firebox. If the glass
becomes cracked or broken follow this procedure for
replacement:
•
Empty stove of all soot and ashes.Only use a vacuum
for this job if the vacuum is specifically designed for
ashes.
Never operate the stove with a cracked or broken glass
•
Inspect the stove; using a strong light inspect the
stove inside and out for cracks or leaks. Replace all
cracked parts and repair any cement leaks with
furnace cement.
panel.
1. Remove the door from the stove and place on a flat
surface.
2. Carefully remove all of the glass clips from the inside
of the door.
3. Gently remove all pieces of the glass panel and
Gaskets
gasketing.
Check door and window gaskets for tightness. To check
the seal of the front doors,close and latch the doors on a
dollar bill and slowly try to pull the dollar bill free. If it
4. Remove all remaining debris from the glass area using
a wire brush.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
can be easily removed then the seal is too loose. Check
several spots around the door,and repeat the procedure
on the ash pan door as well.
Accessories
Many accessories have been manufactured for use with
the Jøtul F 3. Only use accessories that are specifically
designed for the Jøtul F 3.
If gaskets need to be replaced, scrape out the old gasket
and cement and clean the area with a wire brush. Apply
a small bead of cement and push in the new gasket.After
closing and latching the doors wipe clean, any excessive
cement that has come from beneath the gasketing.
Firescreen (part # 350168)
The Jøtul F 3 has been approved for use as an open
fireplace, with front door open.This feature is especially
nice when the ambience of a fire is desired. Some care
should be taken when operating the stove as a fireplace.
Gasket list for the Jøtul F 3
Description
Order # Size
Length
Top plate gasket
100038
3/8” ld
6'
Ash housing gasket 128213
sheet gasket
•
•
•
Always have the firescreen in place, attached to the
stove front.
Ash door gasket
Glass gasket
Door gasket
200024 1/4” ld
200028 1/4” ld
200024 11/32” ld
3'
3’6”
5'
Never over load the stove, for the best appearance
burn in the traditional three log configuration.
Reminder,when burning the stove with the screen in
place,you are sacrificing efficiency for aesthetics,and
you will be consuming wood at a much faster rate.
Air manifold Gasket 200028 3/16”
16”
The Jøtul F 3 is designed to burn cleanly and efficiently
when used according to the guidelines expressed in
these operating instructions. However, to maintain the
proper performance, a yearly chimney inspection and
cleaning in necessary. Failure to keep the chimney
system free of creosote and build up could result in a
serious chimney fire.
Warning: Operate your Jøtul F 3 with the front door fully
open and the firescreen in place or fully closed. A partially
opened door may result in overfiring. Also, if the door is
left partly open, gas and flame may be drawn out of the
stove opening, creating risks from both fire and smoke.
Floor bracket kit (part #750304)
The optional floor bracket kit can be used in the event
the stove needs to be secured to the floor. Complete
installation instructions and diagrams are supplied with
each floor bracket kit.
Stove-top thermometer
(part # 5002)
Jøtul recommends the use of a magnetic stove-top
thermometer to monitor the surface temperature of the
stove. The optimum surface temperature range for the
most efficient, clean burn is between 400° and 600°.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Appendix A:
Alternate floor protection
All floor protection materials must be non-combustible ie.
Metal, brick, stone, mineral fiber boards). Any combustible
material may not be used.
The easiest means of determining if a proposed alternate floor
material meets requirements listed in this manual is to follow
this procedure.
R-value = thermal resistance
K-value = thermal conductivity
C-value = thermal conductance
1. Convert the specification to r-value;
a.
b.
If r-value is given, no conversion is needed.
If k-value is given with a required thickness (t) in
inches: R=1/k X T.
c.
If c-value is given: R=1/C.
2. Determine the r-value of the proposed alternate floor
protector.
a.
Use the formula in step 1 to convert values not
expressed as “R”.
b.
For multiple layers, add r-values of each layer to
determine overall r-value.
3. If the overall R-value of the sustem is greater than the
R-value of the specified floor protector, the alternate is
acceptable.
Example:
The specified floor protector should be 3/4”thick material with
a k-factor of 0.84. The proposed alternate is 4” brick with a c-
factor of 1.25 over 1/8” mineral board witha k-factor of 0.29.
Step A. Use formula above to convert specifications to
R-value. R=1/k x t= 1/.84 x .75 = .893
Step B. Calculate r of proposed system.
4” brick of c-1.25, therefore
R brick = 1/c = 1/1.25 = 0.80
1/8” mineral board of K = 0.29 therefore
R mineral board = 1/.29 x 0.125 = 0.431
Total R = R brick + R mineral board= 0.8 + 0.431=1.231
Step C. Compare proposed system R = 1.231 to specified R of
0.893. Since R is greater than required, the system
is acceptable.
Definitions:
Thermal conductance =
C = btu
=
W
(Hr)(ft2)(f)
(m2)(k)
Thermal conductivity =
K = btu
=
W
=
(btu)
(Hr)(ft2)(f)
(m2)(k)
(hr)(ft)(f)
Thermal resistance =
R = btu
(Hr)(ft2)(f)
=
(m2)(k) =
W
(btu)(inch)
(hr)(ft2)(f)
For the Jøtul F 3 requires floor protection with a minimum
insulating R-value of 1.1.
Alcove installation require a minimum R-value of 1.1. (If a UL/
ULC or whi listed hearth pad is not used.)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
USA/Canada
Part list for Jøtul F 3
No Description, Dim./Spec.
59 Burn plate left
1
Nut brass, M6x20 DIN 1587
Heat shield aluz. f/ivory en.
60 Insulation, Firemaster blanket (after X-607)
2
61 Screw , M8x25 st.8.8
2 b Heat shield
62 Cover/sec. air inlet,
3
Screw, M6x16 DIN 965
63 Screw sinkhead, M6x40 poz DIN 965
64 Gasket-flat
4
5
Nut , M6 DIN 934
Screw collar, M6x16 st.5.6 ubeh.
Cover smoke outlet rear
65 Ash house w\ heat shield and hinge (after 1998)
66 Hinge, ash house (before 1998)
69 Screw sh Pozid, M6x10 DIN 965 (before 1998)
70 Ash box, 1mm steel plate
71 Hinge pin, Ø6x100
6
7
Traverse bar to cover smoke outlet rear
Top plate compl. w/ cover smoke outlet
Gasket, LD 375-2 9.5x1800
8
9
10 Cover smoke outlet side
11 Baffle plate
72 Locking screw, M6x10 DIN915
73 Handle for ashdoor
12 Air distributor USA
13 Cover smoke outlet top
14 Traverse/cover smoke outlet top
15 Back plate
74 Handle stub
75 Spring
76 Door ashroom complete,
77 Gasket, LD 250-2 Ø6.4x730
78 Door latch
16 Screw, M6x35 st.5.6 ubeh
17 Gasket, LD 360 M/L Ø8.7x150
18 Gasket, LD 360 M/L Ø8.7x560
19 Gasket, LD 187-1 M/L Ø4.8x540
20 Cast iron washer
79 Gasket, LD 250 m\l Ø6,4x600
81 Hexagon nut, M8 DIN 934
82 Locking pin, M6x20 DIN 914
83 Fixing bracket
21 Screw, M8x20 st.8.8
22 Side plate
84 Air blocker (for USA)
85 Heat shield rear (for Germany)
86 Heat shield under (for Germany)
87 Extention nut for heat shield, rear (for Germany)
M6x18mm
23 Burn plate, back
24 Burn plate right
26 Air deflektor
27 Gasket, LD 187-1 M/L 4.8x410
28 Sliding vent
88 Distance sleeve for heatshield, under (for Germany)
Ø10xØ6,2x15mm
29 Front plate
89 Self closing mechanism (for Germany)
90 Nut , M10 DIN 934
30 Washer, Ø12x6x0.5
31 Log retainer.
91 Door latch, 3mm stainless steel
92 Spring Ø10 inside, 2mm stainless steel
93 latch bolt ash door, Steel
94 Wooden knob, Hard wood
95 Skrew, M6x60 DIN 84
32 Screw, M6x8 poz
33 Glass clip w\ gasket
34 Gasket, LD 360 Ø8.7x1480
35 Door compl. w/o glass
37 Hinge pin, Ø0,6x33
38 Ignition vent
1-1331-P18
39 Washer, D nr. 531241
40 Cover/ign. vent
41 Screw/collar, M6x12 st. 8.8 ubeh.
42 Handle compl., nickel-plated
43 Locking bar
44 Gasket, LD 187 m\l Ø4,8x1800
45 Glass , 358 x 233 mm
46 Spark screen
48 Spring
49 Knob, plastic, 0,30mm M6
50 Screw collar, M6x16 st. 5.6
51 Ash lip
52 Leg
53 Skrew M6x20 ST 8,8 ubeh.
54 Washer, Ø18x0,6, 4x1
55 Bottom plate,
57 Inner bottom plate
58 Screw sink head, M6x25 sortkrom.poz. (black-poz.)
Only use replacements parts provided through your
authorized Jøtul dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Jøtul pursue a policy of constant product development. Products supplied may therefore
differ in specification, colour and type of accessories from those illustrated and described
in the brochure.
Jøtul vise sans cesse à améliorer ses produits. C’est pourquoi, il se réserve le droit de
modifier les specifications, couleurs et équipements sans avis prélable.
Quality
Jøtul AS has a quality system that conforms to NS-EN ISO 9001 for product development,
manufacturing, and distribution of stoves and fireplaces. This policy gives our customers
quality and safety piece of mind as a result of Jøtul’s vast experience dating back to when
the company first started in 1853.
We appreciate your trust in welcoming our product into your home and invite your
comment and appraisal of our efforts to provide you with the finest in home hearth
products.
Qualité
Le système de contrôle de la qualité de Jøtul AS est conforme à la norme NS-EN ISO 9001
relative à la conception, à la fabrication et à la distribution de poêles, foyers et inserts.
Cette politique nous permet d’offrir à nos clients une qualité et une sécurité reposant sur
la vaste expérience accumulée par Jøtul depuis sa création en 1853.
Jøtul North America
400 Riverside Street
This product has been controlled by:
Ce produit a été contrôlé par :
Portland, Maine 04104
Jøtul AS,
P.o. box 1411
N-1602 Fredrikstad,
Norway
________________________ ___________________
Date:
Sign:
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|