JLWM1202
1200 spin washing machine
JLWM1403
1400 spin washing machine
Instruction manual
Wash time
1200
900
Prewash
30 Minute wash
Spin
Off
90°
Economy 60°
60°
Wash
Rinse
700
Drain
500
Rinse hold
Softeners
Rinse
Soak 30°
Cold
Economy 40°
40°
30°
None
Drain
Spin
Extra
rinse
Delay
start
Start/
Pause
Spin Prewash Intensive Stain
Quiet
Filter
End
Cold
30°
60°
40°
Economy 40°
40°
Delicates 30°
Delicates 40°
30°
JLWM1202
Cold
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Environmental Information
After unpacking please dispose of packaging with
due regard to safety and the environment.
●
For information on maintenance and cleaning your
●
●
●
washing machine see pages 23 - 24 of this
instruction manual.
Materials marked with the symbol
recyclable.
are
Service
●
This product should only be repaired or serviced by
Check with your local Council or Environmental
Health Office to see if there are facilities in your
area for re-cycling this appliance.
anauthorised Service Engineer and only genuine
approvedspare parts should be used.
WARNING:
Ecological hints
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
●
Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
●
The machine works more economically if it is fully
loaded.
●
With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
●
Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
For the User
For the Installer
Important Safety Information
Installation
Child safety feature
2-3
2
Installation
Technical Specifications
Unpacking
Positioning
Installation on a suspended floor
Plumbing in
Water inlet
6
6
7
7
7
7-8
8
2
Description of the Appliance
Door locked light
Detergent dispenser drawer
5
5
5
Water drainage
Levelling
8-9
9
The Control Panel
Programme information
11-14
15
In the interest of the environment
Electrical connection
Permanent connection
9-10
10
10
Using the washing machine
Load the laundry
Measure out the detergent
Measure out the fabric softener
Switch the machine on
Select the desired programme/temperature
Select the spin speed or the “None” option
Select the desired options
Select the “Delay start”
Start the programme
How to change an option or a programme
during its cycle
How to interrupt a programme
How to open the door during the cycle of
a programme
16-18
16
16
16
16
16
17
17
17
17
Maintenance and Cleaning
Descaling
After each wash
Maintenance Wash
External cleaning
Cleaning the dispenser drawer
Cleaning the drawer recess
Cleaning the pump
Cleaning the water inlet filter
The dangers of freezing
Emergency emptying out
23-24
23
23
23
23
23
23
17
18
23-24
24
24
24
18
18
End of programme
Something Not Working
Repairs - After Sales Service
25-26
26
Hints & Tips on Washing
Wash Care Symbols
19
20
Washing Programmes
21-22
Guide to use the Instruction Manual
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the Appliance
1 Detergent dispenser drawer
2 Control panel
1
2
3 Door locked light
4 Door opening handle
5 Drain pump
Wash time
1200
900
Prewash
30 Minute wash
Spin
Off
90°
Economy 60°
60°
Wash
Rinse
700
Drain
500
Rinse hold
Softeners
Rinse
Soak 30°
Cold
Economy 40°
40°
30°
None
Drain
Spin
Extra
rinse
Delay
start
Start/
Pause
Spin Prewash Intensive Stain
Quiet
Filter
End
Cold
30°
60°
40°
Economy 40°
40°
Delicates 30°
Delicates 40°
30°
JLWM1202
Cold
6 Adjustable feet
3
4
5
Door locked light
It stays on during the whole programme indicating that
the door is locked.
6
When the light goes out, the door can be opened.
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
C0110
Child safety feature
This machine incorporates a special child safety feature
to prevent small children from being trapped inside the
machine.
To activate this device, rotate the button (without
pressing it) inside the door clockwise until the groove is
horizontal. If necessary use a coin.
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise until
the groove is vertical.
P1131
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Technical Specifications
DIMENSIONS
Height
Width
Depth
85 cm
60 cm
61 cm
POWER SUPPLY VOLTAGE
TOTAL POWER ABSORBED
230-240 V/50 Hz
2050 W (10A)
WATER PRESSURE
Minimum
Maximum
0.05 MPa (0.5 bar)
0.80 MPa (8. bar)
MAXIMUM RECOMMENDED LOAD
Cotton, linen
Synthetics
Delicate fabrics
Wool/Hand wash/30 Minute wash
6.0 kg
3.0 kg
3.0.kg
2.0 kg
SPIN SPEED
MaximumZ 16 S
1200 rpm (JLWM 1202)
1400 rpm (JLWM 1403)
CONSUMPTION DATA FOR WASHING
6 KG NORMALLY SOILED COTTON
ITEMS WITH PROGRAMME
Energy
Water
1.02 kWh
49 litres
“ COTTONS ECONOMY 60° ”:
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
All transit bolts and packing must be removed
before using the appliance.
Keep all packaging away from children.
You are advised to keep all the transit bolts for re-use
in case the machine is to be transported again.
P1128
P0002
Using a spanner unscrew and remove the two rear
bottom screws. Slide out the two plastic pins.
Positioning
Lay the machine gently on its back, making sure that the
hoses are not squashed.
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen
units.
Never place cardboard, wood or similar materials
under the machine to compensate for any unevenness
in the floor.
If the floor is carpeted or covered with crumbly or soft
material, insert a rigid support base under the feet to
prevent noise, vibration or displacement. The base
should protrude a few centimetres beyond the edges of
the machine.
P0001
P1129
Remove the polystyrene block from the bottom of the
machine and release the two plastic bags.
Very carefully slide out the left polythene bag, removing
it towards the right and then downwards.
Warning
The machine should NOT be placed on deep pile
carpeting.
1
2
Installation on a Suspended
Floor
Suspended wooden floors are particularly susceptible
to vibration. To help prevent vibration we recommend
you place a waterproof wood panel, at least 15 mm
thick under the appliance, secured to at least 2 floor
beams with screws. If possible install the appliance in
one of the corners of the room, where the floor is
more stable.
3
P1124
P1126
Repeat the operation for the right polythene bag,
removing it towards the left and then upwards.
Note
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
P1127
Remove the polystyrene base.
Plumbing In
Set the machine upright and unscrew the remaining
rear screw. Slide out the relevant pin.
Fill all the holes with the plastic plugs supplied with the
instruction booklet.
Your new washing machine has been designed to be
permanently plumbed in to your home’s water supply
and drainage system. However, if this is not possible, it
may be connected to a suitable existing tap with the
drain hose discharging into a sink.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The appliance has an inlet hose, with female 3/4” BSP
thread connector. If this connection is not compatible
with the plumbing of the existing installation, a variety
of connectors are available from good hardware stores
and plumbers merchants to suit most domestic
plumbing. Any alteration to your existing plumbing
must be carried out by a competent person, or
qualified plumber.
Water drainage
This appliance is designed to be permanently plumbed
into your home's drainage system using one of the
following methods.
1. Into a drainage standpipe.
Firstly form a hook in the end of the drain hose using
the “U” piece” supplied.
Water inlet
Connect the hose to a tap with a 3/4” thread.
Always use the hose supplied with the appliance to
connect to the water supply.
Do not use previously used hoses for water
connection.
“U” piece
supplied
P1199
Place the drain hose into your standpipe, which should
have an internal diameter of approximately 38mm thus
ensuring there is an air break between the drain hose
and standpipe.
38 mm (11.2”)
standpipe
diameter
P1088
Installation should comply with local water authority
and building regulations’ requirements.
The appliance must be connected to a cold
water supply.
P1200
A minimum water pressure of 50 kPa (0.5 bar) is
required for safe operation of the appliance.
When discharging into a standpipe ensure that the top
of the standpipe is no more than 90cm (35.4'') and no
less than 60cm (23.6'') above floor level.
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.
There should be a minimum distance of 5.02m
(16.5 ft) between the appliance’s inlet and the bottom
of the water storage tank.
3 pin
Set the hose correctly by loosening the ring nut. After
positioning the inlet hose, be sure to tighten the ring
nut again to prevent leaks.
P1201
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece is
available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
P0021
If your drain hose looks like this (see below) you do
not require the “U” piece”. Just push the hose firmly
into the standpipe.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Levelling
Level the washing machine by raising or lowering the
feet. The feet may be tight to adjust as they incorporate
a self locking nut, but the machine MUST be level and
stable (check diagonally).
P1212
2. Onto a sink outlet spigot.
If the outlet spigot has not been used before, remove
any blanking plug that may be in place.
P1051
Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, (see note on
positioning), noise and displacement of the machine
during operation.
Some vibration is inevitable, especially if mounted on a
wooden floor.
P1197
Sprung wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.
Push the drain hose onto the spigot and secure with a
clip if required, ensure a loop is formed in the drain
hose (see diagram) to prevent waste from the sink
entering the washing machine.
In the interest of the environment
Washing machines and dishwashers should be
connected to the FOUL drainage system, the water will
then be taken to a sewage works for treatment before
being discharged safely into a river.
Loop
P1198
Important
●
Before connecting the machine to new pipework or
SHOWER
to pipework that has not been used for some time,
run off a reasonable amount of water to flush out
any debris that may have collected in the pipes.
SINK TOILET
BATH
BIDET
For a correct functioning of the machine the drain
●
WASHING
MACHINE
hose must be hooked on the proper support piece
situated on the top of the back side of the
appliance.
DISHWASHER
RAINWATER
'RUN-OFF'
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
UNTREATED
DISCHARGE
TREATED
DISCHARGE
RIVER
RIVER
P0987
9
Download from Www.Somanuals.com. All Manuals Search And Download.
It is essential that these appliances are not connected
to the surface water drainage system as this water is
discharged directly into a river or stream and may
cause pollution.
If you require any further advice please contact your
local water authority.
GREEN & YELLOW
E
L
N
BROWN
BLUE
CORD CLAMP
P1041
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
If you fit your own plug, the colours of the wires in
themains lead of your appliance may not correspond
with themarkings identifying the terminals in your
plug.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
Proceed as follows:
1.The wire coloured green and yellow must be
connected to the terminal marked with the letter
The manufacturer declines any liability
should this safety measure not be
observed.
«E» or by the earth symbol
and yellow.
or coloured green
Should the appliance power supply
cableneed to be replaced, this must be
carriedout by a Service Force agent (see
page 19).
2.The wire coloured blue must be connected to the
terminal marked «N» or coloured black.
3.The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
4.Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. The rating plate is located at the top of the
rim of the open door.
WARNING:
A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
P
r o
M
d
o
d
.
.
.
.
.
.
.
.
.
.
.
.
N
o
.
.
.
.
.
.
.
.
.
.
.
.
S e
r
.
N
o
.
.
.
.
.
.
.
.
.
.
The power supply cable must be easily
accessible after installing the appliance.
Mod. ..........
Prod. No. ...........
Ser. No. .........
P0042 BD
Permanent connection
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1363/A) fuse
must be used.
In the case of permanent connection it is necessary
that you install a double pole switch between the
appliance and the electricity supply (mains), with a
minimum gap of 3mm between the switch contacts and
of a type suitable for the required load in compliance
with the current electrical regulations.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires in the mains lead are coloured in accordance
with the following code:
The switch must not break the yellow and green earth
cable at any point.
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
10
Download from Www.Somanuals.com. All Manuals Search And Download.
The Control Panel
Wash time
1200
900
Prewash
30 Minute wash
Spin
Off
90°
Economy 60°
60°
Wash
700
Rinse
Drain
500
Rinse hold
Softeners
Rinse
Soak 30°
Cold
Economy 40°
40°
None
Drain
Spin
Extra
rinse
Delay
start
Start/
Pause
Spin Prewash Intensive Stain
Quiet
30°
Filter
End
Cold
30°
60°
40°
Economy 40°
40°
Delicates 30°
Delicates 40°
30°
JLWM1202
Cold
4
8
5 67
1
2
3
3 Spin button
1 Detergent dispenser drawer
2 Programme selector dial
Press this button repeatedly to change the spin speed
or to select position “None” (no spin), if you want
your laundry to be spun at a speed different from the
one proposed by the washing machine. The relevant
light will light up.
The programme selector dial is divided into the
following sections:
• Cottons,
• Synthetics,
• Delicates
Spin speed
The following speeds are available for the different
fabrics:
• Wool
Hand washing
• Cottons, linen:
500/700/900 max 1200 r.p.m. (for the model JLWM
1202) and 1400 r.p.m. (for the model JLWM 1403);
• Special programmes from “Soak 30°” to “30
Minute wash”
• Synthetics and wool:
500/700 max 900 r.p.m.;
• Reset/Off programme Off
• Delicates and
:
“30 Minute wash”
500 max 700 r.p.m.
30 Minute wash
Spin
Off
90°
Economy 60°
60°
Position “None”
Drain
Softeners
Rinse
Economy 40°
40°
By selecting the option “None” all the spinning
phases are cancelled.
If you select this option with programmes for cotton
and synthetics, the machine will perform some extra
rinses.
Soak 30°
Cold
30°
Cold
30°
60°
40°
Economy 40°
40°
Delicates 30°
Delicates 40°
30°
Cold
The selector dial can be turned either clockwise or
anticlockwise.
4 Option buttons
“Economy” position corresponds to an ENERGY
SAVING programme and “Cold” to a cold wash.
Before setting the dial to any position ensure that the
machine is turned to the “Off” position.
Depending on the programme, different functions can
be combined. These must be selected after choosing
the desired programme and before depressing the
“Start/Pause” button.
Important!
When these buttons are pressed, the corresponding
pilot lights illuminate. When they are pressed again, the
pilot lights go out.
At the end of the programme the selector dial
must be turned to position “Off”.
If an incorrect option is selected, the pilot lights flash for
about 2 seconds and the message “Err” is displayed.
Press these buttons to select the following options:
11
Download from Www.Somanuals.com. All Manuals Search And Download.
• “Prewash”: select this option if you wish your
laundry to be prewashed before the main wash
(not available for Wool and “30 Minute wash”).
The prewash ends with a short spin at 650 rpm in
programmes for cotton and synthetic fabrics,
whereas in the programme for delicate fabrics the
water is only drained. This option can be selected for
heavily soiled laundry but not together with “Stain”
option.
A blinking zero will appear on the display.
To empty out water there are 2 possibilities:
-Select Drain” programme :
“
the water is emptied out without spinning.
-Select the “Spin” programme. Select the spin speed
by means of the relevant button and then depress
the “Start/Pause” button . The water is emptied
out and the laundry is spun at the selected spin
speed.
• “Intensive”: this option can be selected for heavily
soiled cottons and synthetic. If you depress this
button the washing intensity will be increased and the
washing time will be prolonged by few minutes
depending on the selected temperature and type of
fabric.
Attention!
Before selecting Drain” programme or “Spin”
“
programme the selector dial must to be positioned on
“Off”.
This option is not available for “Economy”
programmes, Wool, Delicates and “30 Minute
wash” programmes.
5 Delay start button
This button makes it possible to delay the starting of
the programme from 30 min – 60 min – 90 min, 2
hours and then by 1 hour up to a maximum of 23
hours. The delay you have selected is shown on the
display for about 3 seconds; afterwards, the duration of
the programme reappears.
• “Stain”: select this button if you wish to add to the
washing of heavy soiled laundry a stain phase: at the
temperature of 40°C pour a stain removing
detergent into the compartment marked
.
This function is available in cotton and
synthetic programmes with a temperature of
40° or higher.
The washing time will be prolonged by few minutes.
The “Prewash” and the “Stain” options cannot be
selected together.
The Delay start cannot be selected with “Soak 30°”,
“Drain” and “Spin” programmes.
Selecting the delayed start
You must select this option after you have set the
programme and before you press the Start/Pause
button.
The machine starts its countdown. The programme will
start after the selected delay has expired.
• “Extra rinse”: this option can be selected with all
programmes, except the wool programmes and “30
Minute wash”. The machine will add 2 rinses to the
selected programme.
This option is recommended for people who are
allergic to detergents, and areas where the water is
very soft.
Cancelling the delayed start
If you have already pressed the Start/Pause button, and
you wish to cancel the delay time, proceed as follows:
• set the washing machine to Pause by pressing the
Start/Pause button;
• “Quiet”: when you choose this option, the machine
will not drain the water of the last rinse, this will
ensure the minimum of creasing to laundry.
As all spinning phases are cancelled, this washing cycle
is very quiet and it can be useful at night or in hours
with more economical power rate.
The machine will perform 3 additional rinses on
cottons and 1 additional rinse on synthetics
programmes.
At the end of the cycle, the light corresponding to
the option “Quiet” and the “Rinse hold” pilot
phase light are on, the “Start/Pause” button light
goes out, the door locked light is on and the door
cannot be opened to indicate that the water must be
drained.
• press the “Delay start” button until the display
0’
shows the symbole « ».
• press the “Start/Pause” button again.
Important!
The door will be locked throughout the delay time.
If you need to open the door, you must first set the
washing machine to Pause by pressing the Start/Pause
button. After you have closed the door, press the
Start/Pause button again.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
• The washing machine has stopped with water in
the tub, at the end of the “Soak 30°” or a
programme with the “Quiet” option: this is indicated
by a flashing zero.
6 Start/Pause button
This button has two functions:
• Start: after you have selected the desired programme
and options, press this button to start the washing
machine. The light above the button will stop flashing
and remain lit.
If you have selected a delay time, the countdown will
begin and will be shown on the display.
0
• Pause: when you press this button again, the
programme in progress is interrupted. The light above
the button will start flashing. To restart the
programme from the point at which it was
interrupted, press the button again.
When you PAUSE the cycle, and it becomes possible
to open the door, provided:
• Delay start, a time value indicated in hours and
selected by means of the relevant button.
• the washing machine is not in the heating phase;
• the level of the water is not high;
If all these requirements are met, the door locked light
goes off.
Important! You must set the washing machine to
Pause before you make any change in the programme
in progress.
7 Display
The delay time is displayed for 3 seconds, then the
duration of the selected programme reappears.
After you have pressed the Start/Pause button, the
countdown is updated every hour, and, for the last
two hours, every 30 minutes.
The following pieces of information are shown on the
display:
• Duration of washing programme in hours and
minutes, after you have selected a programme.
• An incorrect option selection has been made:
this is indicated by the message Err when a function
incompatible with the current programme is selected.
2.05
While the programme is running (after you have
pressed the Start/Pause button), the displayed time
value decreases by one unit every minute.
• The washing machine has completed the
programme: this is indicated by a flashing zero.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
• An alarm code indicates a fault in the machine
operation (see the relevant chapter).
The “End” pilot light flashes in the event of operating
problems. And the relative alarm code appears on the
display.
E 10
= the machine does not fill
E 2 0
E 40
= the machine does not empty
= the door has not been closed
E20
To eliminate the problem, see paragraph “Something
not working” (pages 25-26).
ATTENTION!
If you turn the programme selector dial to another
programme when the machine is working, all the lights
of the programme progress display will flash for about 2
seconds but the washing machine will not perform the
new selected programme.
8 Programme phase indicator
lights
When you select a programme, the lights relevant to
the phases that form the programme light up.
After you have started the programme, only the light
relevant to the phase that is currently being carried out
will remain lit.
When the programme has finished, the “End” light
comes on.
Prewash
Wash
Rinse
Rinse hold
Drain
Spin
Filter
End
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme information
Soak 30°
Drain
This is a special programme for heavily soiled laundry.
The machine performs a soak of about 30 minutes at
30°C. At the end of the soak time the machine will
stop automatically with water left in the tub. The
display will show a flashing zero.
For emptying out the water of the last rinse in
programmes with the “Quiet” option or “Soak 30°”
programme. Turn first the programme selector dial to
“Off”, then select the “Drain” programme and
depress the “Start/Pause” button.
Pour the detergent for the soak programme into the
compartment marked
Before starting a new washing phase, it is necessary to
empty the water by selecting the “Drain” programme.
.
Spin
Separate long spin at the max speed for hand washed
garments. The spin speed will automatically assume the
setting for cotton items. You can reduce the speed by
means of “Spin” button to adapt it to the fabrics to be
spun.
This function cannot be used with Wool programmes.
Rinse
With this programme it is possible to rinse and spin the
garments which have been washed by hand. The
machine performs 3 rinses, followed by a final long spin
at the maximum speed.
30 Minute wash
This is a complete programme that can be combined
with the following options:
“Spin” speed reduction, “Quiet” and “Delay start”.
To be used for laundry which is lightly soiled or which
needs freshening up.
Max. load 2 kg.
Washing temperature 30 C.
Important!
The spin speed will automatically assume the setting for
cotton items. If required, reduce the speed to the
desired level by depressing the "Spin" button.
Programme duration 30 minutes.
Final spin speed 700 rpm.
Softeners
Hand washed garments can be be starched or softened
with this programme.
The machine performs 1 rinse, followed by a final long
spin at the maximum speed which can be reduced by
depressing the “Spin” button.
Off = Reset / Switching the machine off
To reset a programme turn the selector dial to “Off”.
Now can a new programme be selected.
The final spin is foreseen only for cotton items as in the
spin programme.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the washing machine
Before the first wash, we recommend that you pour 2 litres
of water into the main wash compartment of the
Close the drawer gently.
detergent drawer in order to activate the ECO valve. Then
run a cotton cycle at 95°C, without any laundry in the
machine, to remove any manufacturing residue from the
drum and tub. Pour 1/2 a measure of detergent into the
dispenser drawer and start the machine.
4. Switch the machine on
Turn the selector dial to any programme to switch the
machine on. To switch the appliance off turn it to
“Off”.
WASHING 5 KG OF WHITE COTTON AT 90°C
Suppose you have 5 kg of laundry to wash. It is white
cotton and is suitable for high temperature washing.
30 Minute wash
Spin
Off
90°
Economy 60°
60°
Drain
Softeners
Rinse
Economy 40°
40°
Soak 30°
Cold
30°
Cold
30°
60°
1.Load the laundry
Open the door. Place the laundry in the drum, one
item at a time, shaking them out as much as possible.
Close the door.
40°
Economy 40°
40°
Delicates 30°
Delicates 40°
30°
Cold
5. Select the desired
programme/temperature
Turn the selector dial to the desired position (Cottons
90° in this case). The lights relevant to the phases that
form the programme will light up.
The display will show the duration of the selected
programme, calculated on the basis of the maximum
load for each type of fabric. The Start/Pause button
light will start flashing.
P0004
2.Measure out the detergent
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent required and pour it into
If the load of laundry to be washed is small, at the
beginning of the cycle the display will still indicate the
duration relevant to the maximum load. The duration
value will be gradually adjusted during the cycle.
the main wash compartment
.
If you wish to carry out the prewash, a soak programme
or a stain phase, pour detergent or stain remover into
the appropriate compartment marked
.
Prewash
Wash
Important!
Rinse
Do not use normal detergent for the “Stain” option,
always use a STAIN remover.
Rinse hold
Drain
2.05
Spin
Filter
End
3.Measure out the fabric softener
If required, pour fabric softener into the compartment
marked , without exceeding the «MAX» mark.
If your laundry needs a soak time, turn the programme
selector dial to “Soak 30°” and then, before starting a
washing cycle, drain the water as described in the
“Soak 30°” paragraph.
C0111
C0112
16
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Select the spin speed or the
“None” option
Press the “Spin” button repeatedly button if order to
select the desired spin speed or the “None” (no spin)
option.
9. Select the “Delay start”
Before you start the programme, if you wish the
start to be delayed, press the “Delay Start” button
repeatedly, or keep it pressed, to select the desired
delay. The selected delay time value (up to 23 hours)
will appear on the display for 3 seconds, then the
duration of the programme will appear again.
The relevant light will light up.
JLWM 1202
JLWM 1403
1200
900
1400
900
Delay
start
700
700
500
500
None
None
Spin
Spin
10. Start the programme
Press the “Start/Pause” button. The relevant light will
stop flashing, and only the light relevant to the phase
that is in progress will remain lit.
If you have chosen a delayed start, the washing machine
will begin the countdown.
The display will show the duration of the programme
or the selected delay.
7. Select the desired options
If your laundry is very dirty, it may be advisable to
select the “Prewash” option or the “Intensive”
option.
If your laundry has heavy stains and it is necessary to
prolong the washing time, select the “Stain” option.
The special detergent for stains (Stain remover) is
loaded from the compartment marked
.
If you wish the laundry to undergo an extra rinse,
select the “Extra Rinse” option.
If your laundry should not be creased, select the
“Quiet” option to leave the fabrics in the water of the
last rinse.
11. How to change an option
or a programme during its
cycle
It is possible to change any option before the
programme carries it out.
The relevant light illuminates.
Before you make any change, you must pause the
washing machine by pressing the “Start/Pause”
button.
Extra
rinse
Prewash Intensive Stain
Quiet
Changing a running programme is possible only by
resetting it.
Turn the programme selector dial to “Off” and then
to the new programme position. The washing water in
the tub will not emptied out .
Start the new programme by depressing the
“Start/Pause” button.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
12.How to interrupt a
programme
Depress the “Start/Pause” button to interrupt a
programme which is running, the corresponding light
starts to flash. Depress the button again to restart the
programme.
14. End of programme
At the end of the programme, the washing machine
stops automatically, the “End” light illuminates, the
“Start/Pause” button light goes off and the display
shows a flashing zero.
If you had selected the “Quiet” option, the door
locked light is on, the door is locked, the “Rinse
Hold” pilot light and the “Quiet” option light remain
lit to indicate that the water must be drained.
The display shows a flashing zero.
13. How to open the door
during the cycle of a
programme
You can open the door, after having set the washing
machine to Pause, provided the following conditions
exist:
To drain or to spin see paragraph “Quiet” on page
12.
Turn the programme selector dial to Reset “Off” to
switch the machine off.
Remove the laundry from the washing machine.
• the washing machine is not in the heating phase
beyond 55°C;
Check whether the drum is completely empty, by
rotating it with your hand. The purpose of this is to
prevent any items of laundry from remaining
accidentally in the drum, where they might get damaged
in a subsequent wash (e.g. by shrinking) or bleed colour
into another load of laundry.
• the level of the water is not high;
If these requirements are met, when you pause the
washing machine, the door locked light goes off and the
door can be opened.
Should it not be possible to open the door, and should
it be absolutely necessary to do so, switch the machine
off by turning the selector dial to “Off”.
We advise you to close the water supply tap and
disconnect the plug from the socket.
Leave the door ajar in order to air the washing
machine.
After approximately 3 minutes, you can open the door.
Pay attention to the level and temperature of
the water in the washing machine!
When you close the door to restart the programme
turn the dial to the previous programme repeating the
options previously selected and press START/PAUSE
button.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Hints & Tips on Washing
●
Do NOT overload the machine. Weigh the laundry the
When washing fabrics requiring different wash
first few times you use the appliance.
temperatures together, always select the lowest
temperature.
The average weights of the most common items are
listed below as a guide:
●
●
●
White items should not be washed with coloured
items.
1000g = 1 kg
Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.
Sheet
700-1000 g
100-200 g
400-500 g
50-100 g
Use a good quality detergent suitable for automatic
washing machines.
Pillow case
Tablecloth
●
●
Use the correct quantities of detergent.
Serviette
For wool, use gentle detergent only in small
quantities.
Tea towel
70-120 g
●
●
Bleach is very corrosive; it should be used with care
and kept out of reach of children.
Linen hand towel
Towelling hand towel
Towelling bath towel
Bath robe
100-150 g
150-250 g
700-1000 g
1000-1500 g
200-300 g
150-200 g
Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special pre-
soak product or biological detergent.
Man’s shirt
Apron
●
If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.
●
Load the laundry loosely alternating large items with
small ones.
●
●
●
Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.
●
Once you have finished using the machine, you are
advised to unplug it and turn off the water tap.
Avoid washing unhemmed or torn items as they
may unravel.
Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc). as these could damage the drain pump.
●
●
●
When washing curtains, remove the hooks.
Close poppers and zips and fasten loose buttons.
It is essential to wash new coloured items separately
when washing for the first time.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Care Symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
FABRIC
White Cotton or Linen
without Special Finishes
Normal (Maximum)
95
Cotton, Linen or Viscose
without Special Finishes
Colourfast at 60°C.
Normal (Maximum)
60
50
Nylon, Polyester/Cotton, Viscose
with Special Finishes,
Cotton/Acrylic Mix.
Reduced (Medium)
Normal (Maximum)
Reduced (Medium)
Cotton, Linen or Viscose
Colourfast at 40°C but not 60°C.
40
40
Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.
Much Reduced (Minimum)
Hand wash only
Wool, wool mixtures, Silks
Do not machine wash
40
BLEACHING
Chlorine bleach may be used
IRONING
Cotton, Linen, Viscose
Polyester mixtures, Wool
Acrylic, Nylon, Polyester
Hot iron
Warm iron
Cool iron
DRY CLEANING
TUMBLE DRYING
May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.
with high heat setting
with low heat setting
May be tumble dried
A cross through any symbol means «DO NOT»
X
fabric conditioner to avoid the conditioner entering the
machine prematurely.
When using liquid detergent and a prewash
programme, place the detergent into the correct
compartment in the dispenser drawer, after the
prewash has finished.
Important Notes
For best results, always use the dispenser drawer for
dispensing detergents and liquid additives.
Once the dispenser has been filled, close it by pushing
it in gently. This is particularly important if you are using
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing programmes
Consumptions*
Available
options
Programme/
temperature
Load
Fabrics
Type of laundry
Energy
Water
litres
Time
kWh
h/min.
Sheets, household
linen, towels,
tablecloths
Spin reduction/None
Prewash, Intensive
Stain, Extra rinse
Quiet
90°
White
6 Kg
2.1
57
1.39
2.35
cotton
Cottons
90°
Cottons
+
Sheets, household
linen, towels,
tablecloths
Spin reduction/None
Prewash, Stain,
White
cotton
2.3
1.02
1.2
57
6 Kg
6 Kg
6 Kg
INTENSIVE
option selected
Extra rinse, Quiet
Economy
60°
Sheets, household
linen, towels,
tablecloths
Spin reduction/None
Prewash, Stain
Extra rinse, Quiet
White
cotton
2.21
1.14
49
57
Cottons
Fast coloured and
non-fast items, for
example hand towels,
sheets, underwear,
tablecloths, shirts
60° - 40°-
30° - Cold
Spin reduction/None
Prewash, Intensive
Stain**, Extra rinse
Quiet
White and
coloured
cotton
Cottons
60°- 40°-
30° - Cold
Cottons +
INTENSIVE
option selected
Fast coloured items,
as hand towels,
sheets, underwear,
tablecloths, shirts
White and
coloured
cotton
Spin reduction/None
Prewash, Stain**
Extra rinse, Quiet
6 Kg
1.3
54
2.10
Economy
40°
Cottons
Spin reduction/None
Prewash
Coloured items, for
example underwear,
shirts, blouses
Coloured
cotton
1.14
0.8
49
42
2.20
1.06
6 Kg
3 Kg
Stain, Extra rinse
Quiet
60° - 40°-
30° - Cold
Spin reduction/None
Prewash, Intensive
Stain, Extra rinse
Quiet
Shirts, blouses,
underwear, mixed
fabrics
Synthetics
Synthetics
Synthetics
60°- 40°-
30° - Cold
Shirts, blouses,
underwear, mixed
fabrics
Spin reduction/None
Prewash, Stain
3 Kg
1.43
Synthetics +
INTENSIVE
option selected
0.95
55
Extra rinse, Quiet
Economy
40°
Shirts, blouses,
underwear, mixed
fabrics
Spin reduction/None
Prewash, Stain
Synthetics
Delicates
3 Kg
3 Kg
0.5
52
57
1.27
1.00
Extra rinse, Quiet
Synthetics
Acrylic, viscose,
polyester items,
curtains
Spin reduction/None
Prewash, Extra rinse
Quiet
40° - 30°
Delicates
0.55
Garments bearing the
“ Pure new wool,
non-shrink, machine
washable” or “Hand
wash” label
40° -
30° - Cold
Wool
Spin reduction/
None
Wool
2 kg
0.35
55
55
Quiet
The “Economy Cottons 60° ” is the reference programme for the data entered in the energy label, in compliance
with EEC 92/75 standards.
* This data is given purely as an indication: the consumption values may vary in relation to the quantity and type
of laundry, the temperature of the water supply and the ambient temperature. The data refers to the highest
temperature provided for each programme.
** Only at a temperature of 40°C or higher.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumptions*
Available
options
Programme
description
Load
Programme
Time
Energy
Water
litres
h/min.
kWh
Soak for 30 minutes
at 30°C
6 Kg
0.23
19
28
Soak 30°
Spin reduction/
None
Extra rinse
Quiet
3 rinses
Long spin at max.
speed
Rinse
6 Kg
6 Kg
45
0.06
-
59
1 rinse with liquid
additive
Long spin at max.
speed
Spin reduction/
None
Softeners
19
-
21
Quiet
Drain
For emptying out the last
rinse of the programmes
with option “Quiet” and
programme “Soak 30°”
6 Kg
6 Kg
-
-
2
Water draining
-
Drain and long spin at
max. speed**
Spin reduction
Spin
-
10
Spin reduction/
None
30 Minute wash
Short cycle for lightly
soiled fabrics
Wash at 30°C
2 rinses
Short spin
2 Kg
0.3
40
30
Quiet
For cancelling the
programme which is
running or to switch
the machine off
-
-
-
-
Off / Reset
** You can reduce the spin speed by means of the relevant button to adapt it to the fabrics to be spun.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
You must DISCONNECT the appliance from the
electricity supply, before you can carry out any
cleaning or maintenance work.
Descaling
The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in the
C0114
C0113
machine. Do this separately from any laundry washing,
and according to the softening powder manufacturer's
instructions. This will help to prevent the formation of
lime deposits.
Cleaning the drawer recess
Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.
After each wash
Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.
Maintenance wash
With the use of low temperature washes it is possible
to get a build up of residues inside the drum.
We recommend that a maintenance wash be
performed on a regular basis.
P0038
Cleaning the pump
The pump should be inspected if
To run a maintenance wash:
●
The drum should be empty of laundry.
●
Select the hottest cotton wash programme.
• the machine does not empty and/or spin
• the machine makes an unusual noise during draining
due to objects such as safety pins, coins etc. blocking
the pump.
●
Use a normal measure of detergent, must be a
powder (such as Ariel Futur).
Proceed as follows:
External cleaning
Clean the exterior cabinet of the appliance with soap
and water only, and then dry thoroughly.
• Disconnect the appliance.
• If necessary wait until the water has cooled down.
• Open the pump door.
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
Remove the drawer by pressing the catch downwards
and by pulling it out. Flush it out under a tap, to
remove any traces of accumulated powder.
To aid cleaning, the top part of the additive
compartment should be removed.
P1114
• Place a container close to the pump to collect any
spillage.
• Pull out the emergency emptying hose, place it in the
container and remove its cap.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
• When no more water comes out, unscrew the pump
cover and remove it. Always keep a rag nearby to dry
up spillage of water when removing the cover.
Tighten up the inlet hose.
P1090
P1115
The dangers of freezing
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
• Remove any objects from the pump impeller by
rotating it.
●
Turn off the water tap.
●
Unscrew the inlet hose.
●
Place the end of the emergency emptying hose and
that of the inlet hose in a bowl placed on the floor
and let water drain out.
●
Screw the water inlet hose back on and reposition
the emergency emptying hose after having put the
cap on again.
●
When you intend to start the machine up again,
make sure that the room temperature is above 0°C.
• Put the cap back on the emergency emptying hose
and place the latter back in its seat.
Important!
Every time you drain the water through the emergency
emptying hose you must pour 2 litres of water into the
main wash compartment of the detergent drawer and
then run the drain programme. This will activate the
ECO valve avoiding that part of the detergent remains
unused at next washing.
P1117
Emergency emptying out
If the water is not discharged, proceed as follows to
empty out the machine:
• Screw the pump cover fully in.
• Close the pump door.
Warning
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
When the appliance is in use and depending on the
programme selected there can be hot water in the
pump. Never remove the pump cover during a wash
cycle, always wait until the appliance has finished the
cycle, and is empty. When replacing the cover, ensure it
is securely retightened so as to stop leaks and young
children being able to remove it.
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove its
cap. The water should drain by gravity into the bowl.
When the bowl is full, put the cap back on the hose.
Empty the bowl. Repeat the procedure until water
stops flowing out;
Cleaning the water inlet filter
If your water is very hard or contains traces of lime
deposit, the water inlet filter may become clogged.
It is therefore a good idea to clean it from time to time.
Turn off the water tap. Unscrew the water inlet hose.
Clean the filter using a hard bristle brush.
• clean the pump if necessary as previously described;
• replace the emergency emptying hose in its seat after
having plugged it;
• screw the pump cover again and close the door.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Not Working
Please carry out the following checks before contacting your local Service Force agent.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by
incorrect use or installation, a charge will be made even if the appliance is under guarantee.
During machine operation it is possible that the “End” light flashes and one of the following alarm codes appears on
the display:
E 10
-
-
-
: problem with the water supply
: problem with water draining
: door open
E 2 0
E 40
Once the problem has been eliminated, press the “Start/Pause” button to restart the programme. If after all
checks, the problem persists, contact your local Service Force Centre.
Symptom
Solution
●
The machine does not start
E 40
The door has not been closed. (
)
●
The plug is not properly inserted in the power socket.
●
●
●
●
There is no supply at the socket.
The main fuse or the fuse in the plug has blown.
The “Start/Pause” button has not been depressed.
The “Delay start” option has been selected.
●
●
●
●
The machine does not fill
E 10
The water tap is closed. (
The filter in the inlet hose is blocked. (
The inlet hose may be squashed or kinked. (
)
E 10
)
E 10
)
E 40
The door has not been closed. (
)
●
●
●
The machine fills then empties
immediately
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
●
●
●
●
●
●
The machine does not empty
and/or does not spin
E 2 0
The drain hose may be squashed or kinked. (
The “Quiet” option has been selected.
)
E 2 0
The drain pump may be blocked. (
)
The “None” option has been selected
The drainage system pipes are blocked.
The programme “Soak 30°”, which ends with water left in the tub,
has been selected .
●
●
There is water on the floor
Too much detergent or unsuitable detergent has been used (creates
too much foam).
Check whether there are any leaks from the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see
if it is damp.
The drain hose may be damaged or not securely positioned.
The cap on the emergency emptying hose has not been replaced after
cleaning the filter.
●
●
●
Unsatisfactory washing results
Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.
●
●
●
Stubborn stains have not been treated prior to washing
The correct wash programme/temperature has not been selected.
Too much laundry has been placed in the drum.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Solution
●
The machine vibrates when
spinning
The internal packing has not been removed.
●
●
●
●
The machine is in contact with the wall or furniture.
The machine is not level and stable (check diagonally).
The washing load is badly distributed in the drum.
Maybe there is very little laundry in the drum.
●
●
●
The door will not open
The water level is above the bottom edge of the door.
The machine is heating the water.
The drum is turning.
In any case the door can be opened only when the door locked
light has gone out.
●
The electronic balance control device has cut in because the laundry is
Spinning starts late or the
machine does not spin
not evenly distributed in the drum. The laundry is redistributed by
reverse rotation of the drum. This may happen several times before
the unbalance disappears and normal spinning can resume. If, after few
minutes, the laundry is still not evenly distributed in the drum, the
machine will not spin. In this case, redistribute the load manually and
select the spin programme.
●
The machine makes an unusual
noise
The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor
ensures a softer start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of the machine.
●
No water is visible in the drum
Machines based on modern technology operate very economically
using very little water without affecting performance.
So that you always have these numbers to hand, we
recommend you to make a note of them here.
Repairs - After Sales Service
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact our
extended warranty administrators by telephoning:
Model..................................................................................................
PNC....................................................................................................
SN........................................................................................................
0870 01 07887
They will give you details for your local Service Force
Centre.
Service Force are the appointed national appliance
repair agents responsible for warranty repairs to this
appliance.
P
r o
M
d .
N
o
d
.
.
.
.
.
.
.
.
.
.
.
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working”.
o
. . . . . . . . . . .
.
S e
r
.
N
o
.
.
.
.
.
.
.
.
.
.
Mod. ..........
Prod. No. ...........
When you contact the Service Force Centre you will
need to give the following details:
Ser. No. .........
P0042 BD
1. Your name, address and post code
2. Your telephone number
Your washing machine is covered by a 3 year
parts and labour guarantee (see separate details
given at point of sale). Please retain your
purchase receipt safely for the service .
3. Clear and concise details of fault
4. The purchase date and found on your receipt.
Please note that a valid purchase receipt is
required for in-guarantee service calls.
5. The model and serial number of the appliance
(found on the rating plate - see picture)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
132 982 380
03/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|