This Manual is Bookmarked
Operating Instructions and Parts Manual
Geared Head Horizontal Band Saw
Model HBS-814GH
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Part No. M-414466
Ph.: 800-274-6848
Revision A 6/05
Copyright © WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty and Service ..............................................................................................................................2
Table of Contents ....................................................................................................................................3
Warning...................................................................................................................................................4
Introduction..............................................................................................................................................6
Specifications ..........................................................................................................................................6
Unpacking ...............................................................................................................................................7
Contents of the Shipping Container ......................................................................................................7
Installation and Assembly ........................................................................................................................8
Installing Motor.....................................................................................................................................8
Wheels and Leveling Stands ................................................................................................................8
Stock Stop............................................................................................................................................8
Shut-Off Switch....................................................................................................................................9
Coolant Hose .......................................................................................................................................9
Grounding Instructions .........................................................................................................................9
Extension cords..................................................................................................................................10
Adjustments...........................................................................................................................................11
Vise....................................................................................................................................................11
Squaring Vise to Blade.......................................................................................................................11
Positioning the Vise............................................................................................................................11
Miter Cuts ..........................................................................................................................................12
Setting Downfeed Rate.......................................................................................................................12
Blade Tension....................................................................................................................................12
Blade Tracking...................................................................................................................................12
Setting Blade Speed...........................................................................................................................13
Blade Guides .....................................................................................................................................14
Blade Replacement............................................................................................................................15
Bow Stop ...........................................................................................................................................15
Operation...............................................................................................................................................16
Troubleshooting.....................................................................................................................................18
Replacement Parts ................................................................................................................................19
Base Assembly ..................................................................................................................................20
Bow Assembly....................................................................................................................................21
Parts List: HBS-814GH Band Saw......................................................................................................22
Gear Box Assembly............................................................................................................................26
Parts List: Gear Box Assembly ...........................................................................................................27
Electrical Control Box Assembly.........................................................................................................28
Parts List: Electrical Control Box Assembly.........................................................................................29
Electrical Connections ...........................................................................................................................30
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
1. Read and understand the entire owners manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This band saw is designed and intended for use by properly trained and experienced personnel only.
If you are not familiar with the proper and safe operation of a band saw, do not use until proper
training and knowledge have been obtained.
5. Do not use this band saw for other than its intended use. If used for other purposes, WMH Tool
Group disclaims any real or implied warranty and holds itself harmless from any injury that may result
from that use.
6. Always wear approved safety glasses/face shields while using this band saw. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this band saw, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips
are recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
•
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
17. Provide for adequate space surrounding work area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area. Keep children away.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
blahblahblah
20. Make your workshop child proof with padlocks, master switches or by removing starter keys.
21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
22. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other
moving parts. Do not overreach or use excessive force to perform any machine operation.
23. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
24. Use recommended accessories; improper accessories may be hazardous.
25. Maintain tools with care. Keep blades sharp and clean for the best and safest performance. Follow
instructions for lubricating and changing accessories.
26. Make sure the work piece is securely clamped in the vise. Never use your hand to hold the work
piece.
27. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do
not use your hands.
28. Check coolant level daily. Replace dirty or weak coolant.
29. Do not stand on the machine. Serious injury could occur if the machine tips over.
30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
31. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
- - SAVE THESE INSTRUCTIONS - -
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures
for a JET Model HBS-814GH Horizontal Band Saw. This manual contains instructions on installation,
safety precautions, general operating procedures, maintenance instructions and parts breakdown. This
machine has been designed and constructed to provide years of trouble free operation if used in
accordance with instructions set forth in this manual. If there are any questions or comments, please
contact either your local supplier or WMH Tool Group. WMH Tool Group can also be reached at our web
Specifications
Model Number....................................................................................................................... HBS-814GH
Stock Number................................................................................................................................ 414466
Round Capacity at 90° (in.)......................................................................................................................8
Round Capacity at 45° (in.)................................................................................................................6-1/2
Rectangle Capacity at 90° (W x H) (in.)............................................................................................ 14 x 8
Rectangle Capacity at 45° (W x H) (in.)........................................................................................ 6-1/2 x 6
Throat Depth (in.).....................................................................................................................................8
Vise Swivel (deg.)..................................................................................................................................45
Blade Wheel Diameter (in.)....................................................................................................................12
Blade Speeds (SFPM) ..........................................................................................................135, 197, 256
Bed Height (in.)......................................................................................................................................26
Motor.............................................................................................. 1HP, 1Ph, 110/220V (pre-wired 110V)
Overall Dimensions (L x W x H)(in.) ......................................................................51-1/2 x 18-1/8 x 44-7/8
Net Weight (lbs.)..................................................................................................................................287
Shipping Weight (lbs.)..........................................................................................................................342
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, WMH Tool Group reserves the right to change specifications at any time and
without prior notice, without incurring obligations.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of the Shipping Container
Unpacking
1
2
2
1
4
2
1
1
1
1
1
1
Band Saw
Open shipping container and accessory boxes,
and check for shipping damage. Report any
damage immediately to your distributor and
shipping agent. Do not discard any shipping
material until the Band Saw is assembled and
running properly.
Leveling Stands (with hex nuts)
Wheels
Axle
Flat Washers
Split Pins
Compare the contents of your container with the
following parts list to make sure all parts are
intact. Missing parts, if any, should be reported
to your distributor. Read the instruction manual
thoroughly for assembly, maintenance and
safety instructions.
Stock Stop
Stock Stop Rod
Can White Touch-Up Paint
Overload Fuse 10A
Owner's Manual
Warranty Card
Read and understand the entire contents of this manual before attempting set-up
or operation! Failure to comply may cause serious injury.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Assembly
Remove all crating and plastic from around the
band saw. Remove any lag screws or holding
straps which secure the band saw to the wood
pallet.
Unpainted areas of the machine have been
treated with a rust preventative. This should be
removed with a soft cloth and a mild solvent. Do
not use paint thinner, lacquer thinner, gasoline
or mineral spirits; these will damage painted and
plastic surfaces. Do not use an abrasive pad.
Installing Motor
Mount the motor to the gearbox using the four
M10 x 30 socket head cap screws and four M10
lock washers, through the holes in the motor’s
flange. See Figure 1. The key in the motor shaft
must line up with the keyway in the gearbox
opening.
Wheels and Leveling Stands
Figure 1
Figure 2
Figure 3
1. Slide the band saw at an angle so that the
edges hang over the sides of the pallet.
2. Insert the axle through the holes at the right
end of the band saw cabinet (opposite the
end where the lifting handle is mounted).
See Figure 2.
3. Install a wheel and two flat washers on each
end of the axle. Insert a split pin through the
hole in the axle and bend the ends of the
split pin to secure the wheel on the axle.
4. Install the two leveling stands at the left end
of the band saw (the end where the lifting
handle is mounted). See Figure 2. Screw
the leveling stand into the hole beneath the
band saw cabinet, and tighten the top hex
nut against the bottom of the cabinet.
5. The leveling stands can be later adjusted for
level by rotating the stand and re-tightening
the hex nut against the cabinet.
6. Roll the band saw off the pallet.
Stock Stop
1. Insert the stock stop rod into the hole at the
front of the base (Figure 3).
2. Secure the rod by tightening the hex cap
screw below the casting.
3. Slide the stock stop onto the rod, and
tighten the thumb screw. The stock stop can
be mounted so it faces either direction.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Shut-Off Switch
Remove the screw and hex nuts which held the
bow to the base during shipment. These should
be retained in case of future transportation of
the Band Saw.
The screw below the limit switch, shown in
Figure 4, has been pre-set at the factory so that
the switch will contact the screw and stop the
blade after each cutting operation.
Coolant Hose
Before operating, the coolant drain hose (Figure
5) must be connected to the coolant pan and the
other end of the hose placed into the filter cup in
the tank as shown.
Figure 4
The hose from the coolant pump is attached to a
valve which should be inserted into the hole on
the guide assembly (see Figure 17).
Grounding Instructions
Electrical connections must
be made by
a
qualified electrician in
compliance with all relevant codes. This
machine must be properly grounded to help
prevent electrical shock and possible fatal
injury.
This machine must be grounded. In the event of
a malfunction or breakdown, grounding provides
a path of least resistance for electric current to
reduce the risk of electric shock.
Figure 5
This band saw is pre-wired for 115 volt and is
equipped with an electric cord having an
equipment-grounding
conductor
and
a
grounding plug similar to that shown in Figure 6.
The plug must be inserted into a matching outlet
that is properly installed and grounded in
accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit
the outlet, have the proper outlet installed by a
qualified electrician.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. The conductor, with insulation
having an outer surface that is green with or
without yellow stripes, is the equipment-
grounding conductor. If repair or replacement of
the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a
live terminal.
Figure 6
Check with a qualified electrician or service
personnel if the grounding instructions are not
completely understood, or if in doubt as to
whether the machine is properly grounded.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
115 Volt Operation
As received from the factory, your band saw is
ready to operate at 115 volt power, using an
outlet and a plug that look similar to those
illustrated in Figure 6.
A temporary adapter, which looks like the
adapter illustrated in Figure 7, may be used to
connect this plug to a two-pole receptacle as
shown, if a properly grounded outlet is not
immediately available. The temporary adapter
Figure 7
should only be used until
a
properly
grounded outlet can be installed by a
qualified electrician.
The green colored rigid ear, lug or tab,
extending from the adapter must be connected
to a permanent ground such as a properly
grounded outlet box, as shown in Figure 7.
Make sure the voltage of your power supply
matches the specifications on the motor plate of
the Band Saw.
Conversion to 220 Volt
If 220 volt, single phase operation is desired, the
following instructions must be followed:
1. Disconnect machine from power source.
2. Open the electrical box and change the
position of the fuse from the 115V slot to the
220V slot. An electrical drawing is included
inside the electrical box, and is also shown
on page 31 of this manual.
3. The 115V attachment plug supplied with the
band saw must be replaced with a UL-listed
plug suitable for 220 volt operation. The
band saw must comply with all local and
national codes after the 220 volt plug is
installed. The band saw with a 220 volt plug
should only be connected to an outlet
having the same configuration (Figure 8).
No adapter is available or should be used
with the 220 volt plug.
Figure 8
Recommended Gauges (AWG) of Extension Cords
Extension Cord Length *
25
50
75
100 150 200
Amps
feet feet feet feet feet feet
Extension cords
< 5
16
16
14
12
10
10
16
16
14
12
10
NR
16
14
12
10
10
NR
14
12
12
10
12
If an extension cord is necessary, make sure the
cord rating is suitable for the amperage listed on
the machine’s motor plate. An undersize cord
will cause a drop in line voltage resulting in loss
of power and overheating. Use only three wire
extension cords that have three-prong
grounding plugs and three-pole receptacles that
accept the machine’s plug.
5 to 8
NR
NR
NR
NR
NR
8 to 12
12 to 15
15 to 20
21 to 30
10
NR
NR
NR
NR
10
NR
NR
Use the chart in Figure 9 as a general guide in
choosing the correct size cord. If in doubt, use
the next heavier gauge. The smaller the gauge
number, the heavier the cord.
*based on limiting the line voltage drop to 5V at 150% of the
rated amperes.
NR: Not Recommended.
Figure 9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
Vise
There are two sets of holes in the bed to mount
the right jaw. The inner hole and slot (A, Figure
10) are used for miter cuts. The outer hole and
slot (B, Figure 10) are used for square, or 90°
cuts. Figure 10 shows the vise located in the “A”
position for miter cuts.
Use only position “A” for miter cuts. If the “A”
position is used for square cuts, it leaves more
blade exposed to the right of the jaw.
Figure 10
Squaring Vise to Blade
(fixed jaw shown in “A” position for mitering)
1. To set up for square cutting, move the right
jaw to “B” position (Figure 10). Place a
machinist’s square on the bed against the
blade and the right vise jaw. The square
should lie along the entire length of the jaw
and blade without a gap.
2. If adjustment is necessary, slightly loosen
the front screw on the right jaw. Loosen the
hex nut at the center of the right jaw and
adjust jaw so the square lines up properly.
3. Re-tighten the hex nut and the front screw.
4. Loosen the handle (C, Figure 10) on the left
jaw. Move the left jaw until it contacts flush
with the right jaw.
Figure 11
5. Tighten the handle (C, Figure 10). The vise
is now set for square cuts.
Positioning the Vise
Keep hands away from blade
while adjusting the vise.
1. The workpiece is placed against the fixed
jaw, which has already been squared (see
“Squaring Vise to Blade”), or has been
locked at the appropriate angle (see “Miter
Cuts”).
2. The vise has a quick-release feature which
allows fast positioning of the movable jaw
against the workpiece and then a final
tightening with the handle. Lift up on the
quick release lever (D, Figure 11), then
push the movable jaw by hand until it
contacts the workpiece.
3. Push down the quick release lever (D,
Figure 11).
4. Turn the lead screw handle (E, Figure 11)
clockwise to continue the tightening process
of the movable jaw until the workpiece is
securely clamped.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The quick release function can also be used
to back off the movable jaw when the cut is
finished.
Miter Cuts
1. For miter cuts, move the fixed jaw to the
inner holes, or “A” position, as shown in
Figure 10.
2. Rotate the fixed jaw to the desired angle,
and tighten the center hex nut.
NOTE: There is an angle scale on the back
side of the bed. This is for reference only.
Check angles with a protractor if greater
precision is needed.
3. Adjust the movable jaw in the manner
described above, and tighten the handle (C,
Figure 10).
Setting Downfeed Rate
The downfeed rate of the blade is important to
band saw performance. Excessive pressure of
blade against the workpiece may break the
blade or stall the saw. In contrast, insufficient
pressure rapidly dulls the blade.
Turn
the
valve
lever
(Figure
12)
counterclockwise to lower the bow. The rate of
downfeed is controlled by the dial setting (Figure
12).
Blade Tension
Blade tension has been set at the factory. When
installing a new blade, use the tension handle
(Figure 13) to adjust blade tension (clockwise to
tighten). Tension is set properly when the
indicator moves into the “green” area on the
scale.
Figure 12
Blade Tracking
Tracking the blade requires
that the band saw be operating while the
back cover is removed. Use extreme caution.
Blade tracking has been tested at the factory.
Adjustment is rarely required when the blade is
used properly and if the blade is correctly
welded. If a tracking problem should occur,
adjust the machine as follows:
Figure 13
1. Raise the bow to its highest position. Make
sure the hydraulic cylinder valve is closed
so the bow remains in place.
2. The blade should be properly tensioned.
NOTE: Keep proper tension on the blade at
all times using the blade tension adjustment.
3. Open the back wheel cover.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
While
performing
the
following steps, keep the blade from rubbing
excessively on the shoulder of the wheel.
Excessive rubbing will damage the wheel
and/or the blade.
4. Start the saw. Turn the set screw (Figure
14) to tilt the idler wheel until the blade is
touching the shoulder of the idler wheel.
5. Turn the set screw (Figure 14) so the blade
starts to move away from the shoulder of
the wheel; then immediately turn the set
screw in the other direction so the blade
stops; then moves slowly towards the
shoulder. NOTE: This adjustment is
sensitive; do it gradually and in small
increments allowing the wheel to respond to
the changes.
Figure 14
Keep your fingers clear of
the blade and wheel to avoid injury.
6. Turn the set screw to stop the shifting of the
blade on the wheel as it gets closer to the
wheel shoulder. Put a six-inch length of
paper between the blade and the wheel.
See Figure 15. The paper should not be cut
as it passes between the wheel shoulder
and the blade.
7. Turn the set screw a small amount. Repeat
the insertion of the paper between the wheel
shoulder and the blade until the paper is cut
into two pieces.
Figure 15
NOTE: You may have to repeat the check
with the paper several times before the
blade and the shoulder cut the paper into
two pieces. Do not hurry the adjustment.
Patience and accuracy here will pay off with
better, more accurate, quieter cutting and
longer machine and blade life.
8. When the paper is cut, back off the set
screw slightly. This assures that the blade is
not touching the shoulder of the wheel.
IMPORTANT: If the blade is allowed to run
against the shoulder of the wheel, it will
wear off the shoulder.
Setting Blade Speed
Rotate the dial (see Figure 16) to the desired
setting – 135, 197 or 256 feet per minute.
Do not change blade speed
during a cutting operation.
Figure 16
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Material chips or shavings are the best indicator
of proper blade speed and downfeed rate. The
ideal chip is thin, tightly curled and warm to the
touch. Chips that range from golden brown to
black indicate excessive force. Blue chips
indicate extreme heat from too high a blade
speed, which will shorten blade life. Thin or
powdered chips indicate insufficient downfeed
rate.
Blade Guides
Loosen the handle (Figure 17) and slide the
guide assembly as close to the workpiece as
possible. This will prevent excessive exposure
of the blade during operation.
[NOTE: The handle (Figure 17) can be adjusted
out of the way. Lift up on the handle and rotate it
on the pin. Release the handle, making sure it
seats itself properly on the pin.]
The guide bearings and carbide guide blocks
come pre-adjusted from the factory, but should
be inspected frequently and adjustments made
as needed. For most efficient operation and
maximum accuracy, provide 0.001” clearance
between the blade and the guide bearings. The
bearings will still turn freely with this clearance.
If the clearance is incorrect, the blade may track
off the drive wheel.
Figure 17
1. Disconnect machine from power source.
2. Loosen the two socket head cap screws (A,
Figure 18) and move the guide seat (B,
Figure 18) up or down until the guide blocks
(D, Figure 18) are positioned adequately
across the width of the blade.
3. Loosen the socket head cap screws (C,
Figure 18) on the carbide guide blocks (D,
Figure 18) and shift both guide blocks until
they place a light pressure on the blade. Re-
tighten the socket head cap screws (C,
Figure 18).
4. The outer guide bearing (E, Figure 18) is
mounted to an eccentric bushing and is
adjustable. Loosen the hex nut (F, Figure
18) and rotate the bearing shaft (G, Figure
18) with a wrench until the bearing (E,
Figure 18
Figure
18)
clears
the
blade
by
approximately .001”. Do not pinch the blade.
5. Re-tighten hex nut (F, Figure 18).
6. Repeat these steps for the other blade
guide assembly.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Replacement
A general-use variable-tooth blade is provided
with this metal cutting band saw. Additional
blades can be used and are available from your
JET distributor.
The choice of blade pitch is governed by the
thickness of the work to be cut: the thinner the
workpiece, the more teeth advised. A minimum
of 3 teeth should engage the workpiece at all
times. If the teeth of the blade are so far apart
that they straddle the work, severe damage to
the workpiece and to the blade can result.
Figure 19
1. Disconnect machine from power source.
2. Loosen the handle (Figure 17) and move
the blade guides away from the wheel, as
shown in Figure 19.
3. Raise the bow, making sure the hydraulic
cylinder is closed so the bow will remain
stationary.
4. Open the back cover, by loosening the two
knobs and the four screws on the brackets.
5. Loosen tension on the blade.
6. Remove the blade from between the guides
and from around the wheels. (Use gloves
when handling sharp blades!).
7. Install new blade on wheels, making sure
the teeth point downward in the proper
cutting direction. See Figure 20; also notice
the blade direction arrow on the front of the
bow.
Figure 20
8. Increase blade tension just enough to hold
the blade on the wheels. Make sure back of
blade rests lightly against the shoulder of
both wheels.
9. Twist blade slightly to allow it to slip into the
guides.
10. The blade should be tensioned and tracked
properly before use. See “Blade Tension”
and “Blade Tracking” above.
Bow Stop
The stop screw (Figure 21) controls the depth of
fall of the bow to prevent the blade from hitting
the bed casting. The stop screw has been set at
the factory. If future adjustment is needed,
loosen the hex nut and rotate the screw, then re-
tighten the hex nut.
Figure 21
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Figure 22 shows the control panel functions.
The Emergency Stop shuts down all functions
on the band saw. The machine will not start if
the emergency stop is still engaged. To start the
machine, twist the emergency stop button until it
pops back out.
IMPORTANT: When cutting magnesium, never
use soluble oils or emulsions (oil-water mix) as
water will greatly intensify any accidental
magnesium chip fire. See your industrial coolant
supplier for specific coolant recommendations
when cutting magnesium.
Figure 22
General Operating Procedure:
1. Give machine an overall inspection. Verify
that all guards, covers, etc. are in place and
in working order, the blade is tensioned
properly and the tooth direction matches the
arrow on the bow. Check that the blade
guides are set correctly, and also the wire
brush.
2. Place workpiece in vise and tighten vise.
The workpiece should be fitted directly
between the jaws without adding other
objects.
When the workpiece to be cut is a profiled
section, flat piece or special shape, refer to
the examples shown in Figure 23 for proper
clamping positions. The top row shows
acceptable clamping positions, the bottom
row shows unacceptable positions.
If the thickness of the profiled section is very
thin, a piece which duplicates the profile
should be fitted inside the workpiece itself,
to prevent the workpiece being crushed
between the jaws.
Figure 23
Never hold a workpiece by
hand when cutting it – the workpiece should
be firmly secured in the vise. Do not reach
into the cutting area during cutting
operations.
3. Rotate the speed dial to the desired setting.
Do not rotate the speed dial during a
cutting operation.
4. Set a suitable downfeed rate for that
operation on the cylinder dial.
5. Push the start button to start the blade
circulating.
6. Turn on the coolant flow.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Open the valve on the hydraulic cylinder to
allow the bow to descend in a gradual and
controlled manner.
8. The machine will shut off at the completion
of the cut. Turn off the coolant flow, and
remove the workpiece.
9. Return the bow to vertical position for the
next cut.
Maintenance
Before doing maintenance
on the machine, disconnect it from the
electrical supply by pulling out the plug or
switching off the main switch. Failure to
comply may cause serious injury.
Clean the band saw regularly after each day’s
work. Clear metal shavings with the provided
brush, do not use your hands. Do not use
compressed air.
To prevent corrosion of machined surfaces
when a soluble oil is used as coolant, pay
particular attention to wiping dry the surfaces
where fluid accumulates and does not evaporate
quickly, such as between the machine bed and
vise.
If the power cord is worn, cut, or damaged in
any way, have it replaced immediately.
All ball bearings are permanently lubricated and
sealed. They require no further lubrication.
Grease the vise lead screw as needed.
Place a thin coat of oil on the bed surface on
which the vise jaw slides.
Maintain coolant level. Low coolant level can
cause foaming and high blade temperatures.
Replace dirty coolant; dirty or weak coolant can
clog the pump, cause crooked cuts, a low
cutting rate and/or permanent blade damage. To
fill the tank, remove the filter cup and pour
coolant into the hole. A “Hi/Lo” mark on the tank
indicates proper level (see Figure 5).
Maintain oil level in the gear box, using SAE No.
10. To check level of the gear box oil, place bow
in down position so that oil drains down. Check
level in sight glass on side of gear casing.
Correct level is the dot in the middle of the sight
glass. Figure 24 shows the locations of the fill
hole, sight glass and drain plug for the gear box.
Completely drain and refill the gear box oil once
a year.
Figure 24
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Trouble
Probable Cause
Remedy
Motor will not start.
No incoming power.
Check plug connection.
Replace fuses.
Blown electrical panel fuses.
Wait several minutes for overload to
reset itself.
Thermal overload has tripped.
Defective motor, switch, power cable, Qualified electrician/service personnel
or plug.
should inspect these items.
Check that motor air intakes are clear.
Reduce downfeed rate.
Overload trips
frequently.
Motor is overheating.
Downfeed rate too fast.
Motor should be inspected by
qualified electrician/service personnel.
Motor is faulty.
Band Saw vibrates
excessively.
Base on uneven surface.
Saw blade has cracks.
Adjust base for even support.
Replace blade immediately.
Reduce downfeed rate and blade
speed.
Too heavy a cut.
Miter cuts not
accurate.
Loosen the screws and adjust the
stops to correct positions. Use an
adjustable square or protractor to
check angle settings.
Setting of the miter stops is not
correct.
Blade is worn, cutting crooked.
Feed pressure too great.
Replace blade.
Cuts not square.
Decrease feed pressure.
Adjust stop until blade is square with
vise.
90° angle stop is not set correctly.
Check Machinist’s Handbook for
recommended blade type.
Incorrect blade toothing in relation to
workpiece.
Blade is worn, cutting crooked.
Replace blade.
Incorrect adjustment of bearing
guides and guide assembly.
Re-adjust these. See page 14.
Workpiece incorrectly positioned in
vise.
Check positioning and clamping in the
vise.
Poor blade tension.
Blade is dull.
Check and correct if needed.
Replace blade.
Finished surface of
workpiece is rough,
unsatisfactory.
Check Machinist’s Handbook for
blade recommendations.
Improper blade for cutting operation.
Downfeed rate too fast.
Blade tension too low.
Reduce downfeed rate.
Increase blade tension.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble
Probable Cause
Remedy
Excessive blade
breakage.
Incorrect blade tension.
Adjust accordingly (see page 12).
Adjust acccordingly.
Incorrect blade speed or downfeed
rate.
Workpiece loose in vise.
Clamp workpiece securely.
Adjust blade tracking.
Blade rubs on wheel shoulder.
Use appropriate blade for material
being cut.
Teeth too coarse for material.
Teeth in contact with workpiece
before saw is started.
Start motor before blade contacts
workpiece.
Blade guides are misaligned.
Adjust as needed. See page 14.
Use thinner blade.
Blade too thick for wheel diameter.
Cracking at weld; poor annealing of
blade.
Replace blade.
Premature Blade
Dulling.
Teeth too coarse.
Use finer tooth blade.
Blade speed too fast.
Inadequate downfeed rate.
Reduce speed.
Adjust cylinder dial setting as needed.
Scale: Reduce speed and increase
downfeed rate. Hard Spots: Increase
downfeed rate.
Hard spots or scale on material.
Work hardening of material
(especially stainless steel)
Increase downfeed rate.
Remove blade, twist inside-out and
re-install.
Blade installed backwards.
Insufficient blade tension.
Adjust as needed.
Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call
1-800-274-6848 between 7:30 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model
Number and Serial Number of your machine available when you call will allow us to serve you quickly and
accurately.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Base Assembly
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Bow Assembly
202
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: HBS-814GH Band Saw
Index No. Part No.
Description
Size
Qty
1...............HBS814GH-001 .............Base............................................................ ...................................1
2...............HBS814GH-002 .............Stand Complete Assembly........................... ...................................1
2-1............HBS814GH-002-1 ..........Coolant Pan ................................................ ...................................1
2-2............HBS814GH-002-2 ..........Leg (Right) .................................................. ...................................1
2-3............HBS814GH-002-3 ..........Leg (Left)..................................................... ...................................1
2-4............HBS814GH-002-4 ..........Panel........................................................... ...................................1
3...............HBS814GH-003 .............Vise Jaw Bracket (Front).............................. ...................................1
4...............HBS814GH-4.................Washer........................................................ 10 x 25 x 2..................2
5...............HBS814GH-005 .............Carriage Bolt ............................................... 1/2"-12 x 2”.................1
6...............TS-0209071 ...................Socket Head Cap Screw.............................. 3/8"-16 x 1-1/2"L.........1
7...............6290483.........................Hex Nut....................................................... 1/2”-12........................1
8...............HBS814GH-063 .............Washer........................................................ 12 x 28 x 2..................2
9...............HBS814GH-009 .............Hex Cap Screw ........................................... 1/2"-12 x 2"L...............1
10.............HBS814GH-010 .............Vise Jaw Bracket (Rear).............................. ...................................1
11.............HBS814GH-011 .............Miter Clamp Bolt.......................................... ...................................1
13.............HBS814GH-013 .............Handle......................................................... ...................................1
14.............HBS814GH-014 .............Crank .......................................................... ...................................1
15.............HBS814GH-015 .............Washer........................................................ 12 x 23 x 2..................1
16.............HBS814GH-016 .............Thrust Flange .............................................. ...................................1
17.............TS-0267051 ...................Socket Set Screw........................................ 1/4"-20 x 1/2"L............1
18.............HBS814GH-018 .............Acme Nut .................................................... ..................................1
19.............HBS814GH-019 .............Acme Screw................................................ ...................................1
20.............HBS814GH-020 .............Pin............................................................... 5 x 34L .......................2
21.............HBS814GH-021 .............Vise Cam .................................................... ...................................1
22.............TS-0051021 ...................Hex Cap Screw ........................................... 5/16"-18 x 5/8"L..........2
23.............HBS814GH-023 .............Washer........................................................ 8 x 25 x 3....................2
24.............HBS814GH-024 .............Shipping Bracket ......................................... ...................................1
25.............TS-0060081 ...................Hex Cap Screw ........................................... 3/8"-16 x 1-3/4"...........1
26.............TS-0060091 ...................Hex Cap Screw ........................................... 3/8"-16 x 2".................1
27.............HBS814GH-285 .............Washer........................................................ 10 x 20 x 2..................1
28.............TS-0561031 ...................Hex Nut....................................................... 3/8”-16........................2
29.............HBS814GH-029 .............Knob ........................................................... ...................................1
30.............HBS814GH-030 .............Shaft ........................................................... ...................................1
37.............HBS814GH-037 .............Fiber washer ............................................... ...................................8
40.............HBS814GH-040 .............Cover .......................................................... ...................................1
41.............TS-081C022...................Phillips Pan Head Machine Screw ............... #10-24 x 3/8"L ............2
50.............HBS814GH-050 .............Stop Block................................................... ...................................1
51.............HBS814GH-051 .............Thumb Screw.............................................. ...................................1
52.............HBS814GH-052 .............Stock Stop Rod ........................................... ...................................1
53.............TS-0051031 ...................Hex Cap Screw ........................................... 5/16"-18 x 3/4"L..........1
54.............TS-0267061 ...................Socket Set Screw........................................ 1/4"-20 x 5/8"L............1
55.............HBS814GH-055 .............Cylinder Lower Support ............................... ...................................1
56.............TS-0060061 ...................Hex Cap Screw ........................................... 3/8"-16 x 1-1/4"L.........2
57.............HBS814GH-285 .............Washer........................................................ 10 x 20 x 2..................2
58.............HBS814GH-058 .............Bearing........................................................ ...................................1
59.............HBS814GH-059 .............Washer........................................................ ...................................1
60.............HBS814GH-060 .............Spring.......................................................... ...................................1
61.............HBS814GH-061 .............Pivot Shaft................................................... ...................................1
62.............HBS814GH-062 .............Bushing....................................................... ...................................1
63.............HBS814GH-063 .............Washer........................................................ 12 x 28 x 2..................2
64.............6290483.........................Hex Nut....................................................... 1/2"-12........................2
69.............HBS814GH-069 .............Bracket........................................................ ...................................1
70.............TS-0060031 ...................Hex Cap Screw ........................................... 3/8"-16 x 3/4"L............1
71.............HBS814GH-071 .............Washer........................................................ 10 x 25 x 3..................1
76.............HBS814GH-076 .............Screen......................................................... ...................................1
77.............TS-0050011 ...................Hex Cap Screw ........................................... 1/4"-20 x 1/2"L............1
81.............TS-081C022...................Phillips Pan Head Machine Screw ............... #10-24 x 3/8"L ............2
22
Download from Www.Somanuals.com. All Manuals Search And Download.
82.............TS-069204 .....................Flat Washer................................................. #10.............................2
83.............HBS814GH-083 .............Scale........................................................... ...................................1
84.............HBS814GH-084 .............Spring.......................................................... ...................................1
85.............HBS814GH-085 .............Spring Adjusting Screw................................ ...................................1
86.............TS-0051031 ...................Hex Cap Screw ........................................... 5/16"-18 x 3/4"L..........1
87.............HBS814GH-087 .............Washer........................................................ 8 x 23 x 2....................1
88.............HBS814GH-088 .............Spring Handle Bracket................................. ...................................1
89.............HBS814GH-092 .............Washer........................................................ 10 x 23 x 2..................1
90.............TS-0561031 ...................Hex Nut....................................................... 3/8-16.........................1
92.............HBS814GH-092 .............Washer........................................................ 10 x 23 x 2..................3
93.............TS-0209061 ...................Socket Head Cap Screw.............................. 3/8"-16 x 1-1/4"L.........3
96.............HBS814GH-096 .............Rear Pivot Bracket....................................... ...................................1
98.............TS-0267051 ...................Socket Set Screw........................................ 1/4"-20 x 1/2"L............1
99.............HBS814GH-099 .............Cylinder Upper Support ............................... ...................................1
100...........HBS814GH-100 .............Shaft .......................................................... ...................................1
101...........TS-0060051 ...................Hex Cap Screw ........................................... 3/8"-16 x 1"L...............2
102...........HBS814GH-4.................Washer........................................................ 10 x 25 x 2..................2
103...........HBS814GH-103 .............Cylinder Complete Set................................. ...................................1
105...........HBS814GH-105 .............Cross Round Head Screw ........................... 1/4"-20 x 5/8"L............4
106...........HBS814GH-106 .............Washer........................................................ 6.3 x 19 x 1.5..............4
107...........HBS814GH-107 .............Pump..................................................1/8HP,110/220V, 1PH ............1
108...........HBS814GH-108 .............Close Nipple................................................ 3/8"PT ........................1
109...........HBS814GH-109 .............Hose ........................................................... OD12 x ID8 x 2000 .....1
110...........HBS814GH-110 .............Hose Clip .................................................... 5/8".............................3
111...........TS-081C022...................Phillips Pan Head Machine Screw ............... #10-24 x 3/8"L ............3
113...........HBS814GH-092 .............Washer........................................................ 10 x 23 x 2..................2
114...........TS-0209031 ...................Socket Head Cap Screw.............................. 3/8"-16 x 3/4"L............2
118...........HBS814GH-118 .............Hose ........................................................... OD16 x ID13 x 260 .....1
119...........HBS814GH-119 .............Coolant Tank............................................... ...................................1
126...........HBS814GH-126 .............Washer........................................................ 5/8" x 40 x 3" ..............4
127...........HBS814GH-127 .............Wheel.......................................................... ...................................2
128...........5519932.........................Cotter Pin.................................................... 3 x 25L .......................2
129...........HBS814GH-129 .............Wheel Rod .................................................. ...................................1
133...........6290483.........................Hex Nut....................................................... 1/”2-12........................2
134...........HBS814GH-134 .............Coaster of Stand ......................................... 1/2".............................2
137...........TS-0680041 ...................Washer........................................................ 3/8".............................8
138...........TS-0060051 ...................Hex Cap Screw ........................................... 3/8"-16 x 1"L...............8
139...........HBS814GH-139 .............Handle......................................................... ...................................1
140...........HBS814GH-140 .............Flat Cross Head Screw................................ M5-0.8 x 12L...............1
141...........TS-1523051 ...................Socket Set Screw........................................ M6-1 x 15L .................4
142...........HBS814GH-142 .............Door Clip Lower........................................... ...................................2
143...........HBS814GH-143 .............Washer........................................................ 6.3 x 16 x 1.5..............4
144...........TS-0050011 ...................Hex Cap Screw ........................................... 1/4"-20 x 1/2"L............4
146...........HBS814GH-146 .............Body Frame................................................. ...................................1
147...........TS-0720091 ...................Lock Washer ............................................... 3/8".............................4
148...........TS-0060061 ...................Hex Cap Screw ........................................... 3/8"-16 x 1-1/4"L.........4
152...........HBS814GH-152 .............Upper Bracket hold down............................. ...................................1
153...........HBS814GH-285 .............Washer........................................................ 10 x 20 x 2..................2
154...........TS-0060051 ...................Hex Cap Screw ........................................... 3/8"-16 x 1".................2
155...........HBS814GH-155 .............Blade.............................................0.032" x 3/4" x 2464L x 5-8T" ......1
156...........HBS814GH-156 .............Drive Wheel................................................. ...................................1
157...........TS-0267051 ...................Socket Set Screw........................................ 1/4"-20 x 1/2"L............1
158...........5519933.........................C-Retainer Ring........................................... S25.............................1
159...........HBS814GH-159 .............Blade Back Cover........................................ ...................................1
160...........HBS814GH-143 .............Washer........................................................ 6.3 x 16 x 1.5..............4
161...........HBS814GH-161 .............Knob ........................................................... ...................................4
163...........HBS814GH-163 .............Clamp Block Guide Arm .............................. ...................................1
164...........TS-1550071 ...................Flat Washer................................................. M10............................1
165...........HBS814GH-165 .............Grip............................................................. M10-1.5 x 52L.............1
166...........HBS814GH-166 .............Idler Wheel Assembly.................................. ...................................1
166-1........HBS814GH-166-1 ..........Idler Wheel.................................................. ...................................1
23
Download from Www.Somanuals.com. All Manuals Search And Download.
166-2........HBS814GH-166-2 ..........Bearing Cover ............................................. ...................................1
166-3........HBS814GH-211 .............Washer........................................................ 8 x 18 x 1.5.................1
166-4........TS-0051031 ...................Hex Cap Screw ........................................... 5/16"-18 x 3/4"L..........1
166-5........HBS814GH-166-5 ..........Phillips Flat Head Screw.............................. #10-24 x 3/8"L ............3
166-6........HBS814GH-166-6 ..........Bushing....................................................... ...................................1
166-8........BB-6202ZZ.....................Bearing........................................................ 6202ZZ.......................2
166-9........HBS814GH-166-9 ..........Bushing....................................................... ...................................1
173...........HBS814GH-173 .............Shaft Assembly ........................................... ...................................1
173-1........HBS814GH-173-1 ..........Sliding Plate Draw Block.............................. ...................................1
173-2........HBS814GH-173-2 ..........Blade Wheel Shaft....................................... ...................................1
173-3........HBS814GH-173-3 ..........Pin............................................................... 4 x 22L .......................1
174...........HBS814GH-174 .............Control Box Assembly ................................. ...................................1
174-1........HBS814GH-174-1 ..........Control Box ................................................. ...................................1
174-2........HBS814GH-174-2 ..........Control Plate ............................................... ...................................1
174-3........HBS814GH-174-3 ..........Label for Name Plate................................... ...................................1
174-4........TS-1533042 ...................Phillips Pan Head Machine Screw ............... M5-0.8P*12L...............4
174-5........TS-1550041 ...................Flat Washer................................................. M6..............................2
174-6........TS-1482031 ...................Hex Cap Screw ........................................... M6-1.0 x 15L...............2
175...........TS-0561031 ...................Hex Nut....................................................... 3/8-16.........................1
176...........HBS814GH-176 .............Sliding Plate ................................................ ...................................2
177...........HBS814GH-177 .............Blade Tension Slide Block ........................... ...................................1
178...........TS-0270071 ...................Socket Set Screw........................................ 5/16"-18 x 3/4"L..........1
179...........TS-0051071 ...................Hex Cap Screw ........................................... 5/16"-18 x 1-1/2"L.......2
180...........HBS814GH-180 .............Washer........................................................ 8 x 12 x 2....................2
181...........TS-0051031 ...................Hex Cap Screw ........................................... 5/16"-18 × 3/4"L..........4
182...........TS-0720081 ...................Lock Washer ............................................... 5/16"...........................4
186...........HBS814GH-200 .............Phillips Pan Head Machine Screw ............... 1/4"-20 x 3/8"L............1
187...........HBS814GH-187 .............Blade Guard................................................ ...................................1
190...........HBS814GH-190 .............Blade Guide Assembly ................................ ...................................1
190-1........HBS814GH-190-1 ..........Blade Guide ................................................ ...................................1
190-2........HBS814GH-190-2 ..........Adjustable Bracket (Front)........................... ...................................1
190-3........HBS814GH-211 .............Washer........................................................ 8 x 18 x 1.5.................2
190-4........TS-0720081 ...................Lock Washer ............................................... 5/16"...........................2
190-5........TS-0208071 ...................Socket Head Cap Screw.............................. 5/16"-18 x 1-1/4”L.......2
190-6........TS-1523031 ...................Socket Set Screw........................................ M6-1P*10L .................2
190-7........TS-1503041 ...................Socket Head Cap Screw.............................. M6-1 x 15L .................2
190-8........TS-1540071 ...................Hex Nut....................................................... M10-1.5 x P1..............2
190-9........TS-2361101 ...................Lock Washer ............................................... M10............................2
190-10......HBS814GH-190-10 ........Carbide Guide............................................. ...................................2
190-11......TS-0207041 ...................Socket Head Cap Screw.............................. 1/4"-20 x 3/4"L............2
190-12......HBS814GH-190-12 ........Top Guide Left............................................. ...................................1
190-13......TS-1503021 ...................Socket Head Cap Screw.............................. M6-1 x 10 ...................1
191...........HBS814GH-191 .............Eccentric shaft Assembly............................. ...................................2
191-1........HBS814GH-191-1 ..........Eccentric shaft............................................. ...................................2
191-2........BB-608ZZ ......................Bearing........................................................ 608ZZ.........................2
191-3........5515607.........................C-Retaining Ring......................................... S10.............................2
192...........HBS814GH-192 .............Bearing Shaft Assembly .............................. ...................................2
192-1........HBS814GH-192-1 ..........Bearing Shaft............................................... ...................................2
192-2........BB-608ZZ ......................Bearing........................................................ 608ZZ.........................2
192-3........5515607.........................C-Retaining Ring......................................... S10.............................2
198...........HBS814GH-198 .............Brush Assembly .......................................... ...................................1
198-1........HBS814GH-198-1 ..........Brush Support ............................................. ...................................1
198-2........HBS814GH-198-2 ..........Brush .......................................................... ...................................1
198-3........HBS814GH-198-3 ..........Bushing....................................................... ...................................1
198-4........HBS814GH-285 .............Washer........................................................ 10 x 20 x 2..................1
198-5........TS-1523031 ...................Socket Set Screw........................................ M6-1 x 10L .................1
198-6........HBS814GH-198-6 ..........Bushing....................................................... ...................................1
200...........HBS814GH-200 .............Phillips Pan Head Machine Screw ............... 1/4"-20 x 3/8"L............2
201...........TS-0680021 ...................Flat Washer................................................. 1/4".............................2
202...........HBS814GH-202 .............Blade Guide Assembly ................................ ...................................1
202-1........HBS814GH-202-1 ..........Blade Adjustable ......................................... ...................................1
24
Download from Www.Somanuals.com. All Manuals Search And Download.
202-5........TS-1540071 ...................Hex Nut....................................................... M10-1.5 x P1..............2
202-6........TS-2361101 ...................Lock Washer ............................................... M10............................2
202-13......HBS814GH-202-13 ........Carbide Guide............................................. ...................................2
202-14......TS-0207041 ...................Socket Head Cap Screw.............................. 1/4"-20 x 3/4"L............2
202-15......HBS814GH-202-15 ........Top Guide Right .......................................... ...................................1
211...........HBS814GH-211 .............Washer........................................................ 8 x 18 x 1.5.................2
212...........TS-0720081 ...................Lock Washer ............................................... 5/16"...........................2
213...........TS-0208121 ...................Socket Head Cap Screw.............................. 5/16"-18 x 2-1/2"L.......2
231...........HBS814GH-231 .............Handle Body................................................ ...................................1
232...........HBS814GH-232 .............Blade Tension Bar....................................... ...................................1
233...........HBS814GH-233 .............Knob ........................................................... ...................................2
234...........HBS814GH-234 .............Indicator plate.............................................. ...................................1
235...........HBS814GH-235 .............Thrust Rearing............................................. 10 x 25 x 2..................2
238...........HBS814GH-238 .............Sleeve......................................................... ...................................1
239...........HBS814GH-239 .............Spring.......................................................... 23 x 12.2 x 1.5t...........8
240...........HBS814GH-240 .............Scale........................................................... ...................................1
241...........HBS814GH-241 .............Rivet............................................................ Ø2 x 6.........................2
249...........HBS814GH-249 .............Spring.......................................................... ...................................1
271A.........HBS814GH-271A...........Electrical Control Box ................................. ...................................1
272...........HBS814GH-272 .............Cable Clamp ............................................... ...................................2
281...........TS-081F052...................Pan Head Phillips Screw.............................. 1/4"-20 x 3/4"L............8
282...........HBS814GH-143 .............Washer........................................................ 6.3 x 16 x 1.5............16
283...........TS-0570011 ...................Hex Nut....................................................... 1/4-20.........................8
284...........TS-0060051 ...................Hex Cap Screw ........................................... 3/8"-16 x 1"L...............8
285...........HBS814GH-285 .............Washer........................................................ 10 x 20 x 2................16
286...........TS-0561031 ...................Hex Nut....................................................... 3/8-16.........................8
287...........HBS814GH-287 .............Valve Assembly........................................... ...................................1
287-1........HBS814GH-287-1 ..........Micro Control Block ..................................... PT1/8" x 1/4"...............1
287-2........HBS814GH-287-2 ..........Valve........................................................... PT1/8" x 1/8"...............1
287-3........HBS814GH-287-3 ..........Jet Pipe....................................................... ...................................1
287-4........HBS814GH-287-4 ..........O-Ring......................................................... 8 x 4.5 x 1.9................1
290...........HBS814GH-105 .............Cross Socket Head Screw........................... 1/4"-20 x 5/8"L............2
291...........HBS814GH-143 .............Washer........................................................ 6.3 x 16 x 1.5..............2
292...........HBS814GH-292 .............Support Plate............................................... ...................................1
400...........HBS814GH-400 .............Limit Plate ................................................... ...................................1
401...........HBS814GH-143 .............Washer........................................................ 6 x 16 x 1.5mm...........2
402...........TS-0207031 ...................Socket Head Cap Screw.............................. 1/4”-20 x 5/8”..............2
403...........TS-0570011 ...................Nut .............................................................. 1/4”.............................1
404...........TS-0208071 ...................Socket Head Cap Screw.............................. 5/16”-18 x 1-1/4”.........1
405...........HBS814GH-405 .............Bracket........................................................ ...................................1
406...........TS-1550041 ...................Washer........................................................ M6..............................2
407...........TS-133032 .....................Pan Head Phillips Screw.............................. M5-0.8 x 10 ................2
408...........HBS814GH-408 .............Limit Switch................................................. ...................................1
409...........TS-1550021 ...................Washer........................................................ M4..............................2
410...........HBS814GH-410 .............Pan Head Phillips Screw.............................. M4-0.4 x 30L...............2
800...........HBS814GH-800 .............Gear Box Assembly..................................... ...................................1
801...........HBS814GH-801 .............Key.............................................................. 6 x 6 x 40L..................1
802...........HBS814GH-802 .............Motor.................................................1HP, 110/220V, 60HZ,1PH......1
803...........TS-1505041 ...................Socket Head Cap Screw.............................. M10-1.5 x 30L.............4
804...........TS-2361101 ...................Lock Washer ............................................... M10............................4
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Gear Box Assembly
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Gear Box Assembly
Index No. Part No.
Description
Size
Qty
..................HBS814GH-800............Gear Box Assembly..................................... ...................................1
800-1.........HBS814GH-800-1.........Gear Box Enclosure .................................... ...................................1
800-2.........HBS814GH-800-2.........Gear Box Cover........................................... ...................................1
800-3.........HBS814GH-800-3.........Speed-Changing Gear Shaft ....................... ...................................1
800-4.........HBS814GH-800-4.........Speed Lever................................................ ...................................1
800-5.........HBS814GH-800-5.........Spring.......................................................... ...................................1
800-6.........SB-8MM........................Steel Ball..................................................... 8.................................1
800-7.........HBS814GH-800-7......... Speed Indicator Dial ................................... ...................................1
800-8.........TS-1502071..................Socket Head Cap Screw.............................. M5-0.8 x 28L...............1
800-9.........HBS814GH-800-9.........Worm Shaft ................................................. ...................................1
800-10.......HBS814GH-800-10.......Speed-Changing Rod .................................. ...................................1
800-11.......HBS814GH-800-11.......Speed-Changing Key................................... ...................................1
800-12.......HBS814GH-800-12.......Torsion Spring............................................. ...................................1
800-13.......HBS814GH-800-13.......Pin............................................................... 3 x 10L .......................2
800-14.......HBS814GH-800-14.......Gear............................................................ ...................................1
800-15.......HBS814GH-800-15.......Gear............................................................ ...................................1
800-16.......HBS814GH-800-16.......Gear............................................................ ...................................1
800-17.......HBS814GH-800-17.......Washer........................................................ ...................................4
800-18.......HBS814GH-800-18.......Bushing Bracket .......................................... ...................................1
800-19.......PWBS14-123................C-Retainer Ring........................................... R35 ............................2
800-20.......TS-1523011..................Socket Set Screw........................................ M6-1 x 6L ...................2
800-21.......HBS814GH-800-29.......Bearing........................................................ 6003LLB.....................2
800-22.......HBS814GH-800-22.......Cover .......................................................... ...................................1
800-23.......HBS814GH-800-23.......Gear Shaft................................................... ...................................1
800-24.......HBS814GH-800-24.......Gear............................................................ ...................................1
800-25.......HBS814GH-800-25.......Gear............................................................ ...................................1
800-26.......HBS814GH-800-26.......Gear............................................................ ...................................1
800-27.......6291479........................Key.............................................................. 5 x 5 x 32L..................1
800-28.......5513018........................C-Retainer Ring........................................... S17.............................2
800-29.......HBS814GH-800-29.......Bearing........................................................ 6003LLB.....................1
800-30.......HBS814GH-800-30.......Bearing........................................................ 6007LLB.....................1
800-31.......HBS814GH-800-31.......C-Retainer Ring........................................... R62 ............................1
800-33.......HBS814GH-800-33.......Oil Seal ....................................................... 62 x 35 x 8..................1
800-37.......HBS814GH-800-37.......Drive Gear Shaft ......................................... ...................................1
800-38.......HBS814GH-800-38.......Worm Gear.................................................. ...................................1
800-39.......5519933........................C-Retainer Ring........................................... S25.............................2
800-40.......1020A-292 ....................Key.............................................................. 6 x 6 x 20L..................2
800-41.......HBS814GH-800-41.......Bearing........................................................ 60205LLB...................2
800-42.......HBS814GH-800-42.......Bearing Spacer............................................ ...................................1
800-43.......HBS814GH-800-43.......Cover .......................................................... ...................................1
800-44.......HBS814GH-800-44.......O-Ring......................................................... 35 x 29 x 3..................2
800-45.......TS-1533042..................Cross Round Head Screw ........................... M5-0.8 x 13L...............3
800-46.......HBS814GH-800-46.......Plug............................................................. PT3/8" ........................1
800-47.......TS-1503051..................Socket Head Cap Screw.............................. M6-1 x 20L .................4
800-48.......HBS814GH-800-48.......Vent Plug .................................................... ...................................1
800-49.......HBS814GH-800-49.......Scale........................................................... ...................................1
800-50.......HBS814GH-800-50.......Rivet............................................................ 2 x 4 ...........................2
800-51.......HBS814GH-800-51.......Bearing Cover ............................................. ...................................1
800-52.......TS-1533032..................Cross Round Head Screw ........................... M5-0.8 x 10L...............3
800-53.......HBS814GH-800-53.......Gear Box Gasket......................................... ...................................1
800-54.......HBS814GH-800-54.......Plug............................................................. PT1/4" ........................1
800-55.......HBS814GH-800-55.......Oil level gauge............................................. 19...............................1
800-56.......HBS814GH-800-56.......O- Ring........................................................ 15.8 x 2.4b..................1
800-57.......HBS814GH-800-57.......C-Retainer Ring........................................... R20 ............................1
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Control Box Assembly
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Electrical Control Box Assembly
Index No. Part No.
Description
Size
Qty
.................HBS814GH-271A...........Electrical Control Box Assembly .................. ...................................1
271-1........HBS814GH-271-1 ..........Relay........................................................... ...................................1
271-2........HBS814GH-271-2 ..........Magnetic Contactor ..................................... ...................................1
271-3........HBS814GH-271-3 ..........Push-Button Stop ........................................ ...................................1
271-4........HBS814GH-271-4 ..........Push-Button Switch ..................................... ...................................1
271-5........HBS814GH-271-5 ..........Selector Switch............................................ ...................................1
271-6........HBS814GH-271-6 ..........Emergency-Stop Switch .............................. ...................................1
271-7........HBS814GH-271-7 ..........Transformer................................................. ...................................1
271-8........HBS814GH-271-8 ..........End Clip Dinn .............................................. ...................................1
271-10......HBS814GH-271-10 ........Fuse-Base................................................... ...................................2
271-11......HBS814GH-271-11 ........Fuse-Lid...................................................... ...................................1
271-12......HBS814GH-271-12 ........Fuse............................................................ ...................................1
271-13......HBS814GH-271-13 ........Cover Electrical Enclosure........................... ...................................1
271-14......HBS814GH-271-14 ........Electrical Enclosure..................................... ...................................1
271-17......HBS814GH-271-17 ........Cord Grip (18/2 SJT) ................................... ...................................1
271-18......HBS814GH-271-18 ........Cord Grip (14/3 SJT) ................................... ...................................4
271-19......HBS814GH-271-18 ........Cord Grip (14/4 SJT) ................................... ...................................3
271-20......HBS814GH-271-20 ........Mount Grill................................................... ...................................1
271-21......HBS814GH-271-21 ........Din-Rails ..................................................... ...................................1
271-22......HBS814GH-271-22 ........Auto-Reset .................................................. ...................................1
271-23......HBS814GH-271-23 ........Auto-Reset .................................................. ...................................1
271-24......HBS814GH-271-24 ........Ground strip ................................................ ...................................1
271-25......HBS814GH-271-25 ........Power Cable................................................ ...................................1
271-26......HBS814GH-271-26 ........Motor Cable................................................. ...................................1
271-27......HBS814GH-271-27 ........Limit Cable.................................................. ...................................1
271-28......HBS814GH-271-28 ........Pump Cable ................................................ ...................................1
271-29......HBS814GH-271-29 ........Control Cable .............................................. ...................................1
271-33......TS-133032 .....................Phillips Pan Head Machine Screw ............... M5 × 8........................4
271-34......HBS814GH-271-34 ........Tap Screw................................................... M4 × 8......................16
271-35......TS-2284082 ...................Phillips Pan Head Machine Screw ............... M4 × 8........................5
271-36......TS-1532052 ...................Phillips Pan Head Machine Screw ............... M4 × 15......................4
271-37......TS-1550031 ...................Washer........................................................ M5..............................6
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
30
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
WMH Tool Group
2420 Vantage Drive
Elgin, Illinois 60123
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|