OWNER'S MANUAL
EHVS-80CS Edge Horizontal/Vertical Sander
JET EQUIPMENT & TOOLS, INC.
A WMH Company
P.O. BOX 1349
Auburn, WA 98071-1349
e-mail [email protected]
253-351-6000
Fax 253-939-8001
M-708448
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
12. Make certain the switch is in the OFF
position before connecting the machine to
the power supply.
1. Read and understand the entire
instruction manual before attempting
assembly or operation.
13. Give your work undivided attention.
Looking around, carrying on a conversation,
and "horse-play" are careless acts that can
result in serious injury.
2. This sander is designed and intended for
use by properly trained and experienced
personnel only. If you are not familiar
with the proper and safe operation of a
sander, do not use until proper training
and knowledge have been obtained.
14. Keep visitors a safe distance from the work
area.
3. Always wear approved safety glasses/face
shields while using this machine.
15. Use recommended accessories; improper
accessories may be hazardous.
4. Make certain the machine is properly
grounded.
16. Read and understand warnings posted on
the machine.
5. Before operating the machine, remove tie,
rings, watches, other jewelry, and roll up
sleeves above the elbows. Remove all
loose clothing and confine long hair. Do not
wear gloves.
17. Failure to comply with all of these warnings
may cause serious injury.
18. Some dust created by power sanding,
sawing, grinding, drilling and other
construction activities contains chemicals
known to cause cancer, birth defects or
other reproductive harm. Some examples
of these chemicals are:
6. Keep the floor around the machine clean
and free of scrap material, oil and grease.
7. Keep machine guards in place at all times
when the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately.
•
•
Lead from lead based paint
crystalline silica from bricks and cement
and other masonry products, and
8. Do not over reach. Maintain a balanced
stance at all times so that you do not fall or
lean against blades or other moving parts.
•
arsenic and chromium from chemically-
treated lumber.
19. Your risk from those exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are
specifically designed to filter out
9. Make all machine adjustments or
maintenance with the machine unplugged
from the power source.
10. Use the right tool. Don't force a tool or
attachment to do a job that it was not
designed for.
microscopic particles
11. Replace warning labels if they become
obscured or removed.
20. Do not operate tool while under the
influence of drugs, alcohol or any
medication.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
Caution: This tool must be grounded while in use to protect the operator from electric shock.
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The
conductor, with insulation having an outer surface that is green with or without yellow stripes, is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is properly grounded. Use only three wire extension
cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug.
Repair or replace a damaged or worn cord immediately.
115 Volt Operation
As received from the factory, your sander is ready to run at 115 volt operation. This sander, when wired
for 115 volt, is intended for use on a circuit that has an outlet and a plug that looks like the one illustrated
in (A). A temporary adapter, which looks like the adapter as illustrated in (B), may be used to connect
this plug to a two-pole receptacle, as shown in (B) if a properly grounded outlet is not available. The
temporary adapter should only be used until a properly grounded outlet can be installed by a qualified
electrician. This adapter is not applicable in Canada. The green colored rigid ear, lug, or tab,
extending from the adapter, must be connected to a permanent ground such as a properly grounded
outlet box, as shown in (B).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
230 Volt Operation
WARNING!
All electrical connections must be done by a qualified electrician!
Failure to comply may result in serious injury!
If 230V operation is desired, the following instructions must be followed:
1. Disconnect the machine from the power source.
2. This sander is supplied with four motor leads that are connected for 115V operation, as shown in
Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B.
3. The 115V attachment plug (A), supplied with the sander, must be replaced with a UL/CSA listed plug
suitable for 230V operation (D). Contact your local Authorized JET Service Center or qualified
electrician for proper procedures to install the plug. The sander must comply with all local and
national codes after the 230 volt plug is installed.
4. The sander with a 230 volt plug should only be connected to an outlet having the same configuration
(D). No adapter is available or should be used with the 230 volt plug.
Important: In all cases (115 or 230 volts), make certain the receptacle in question is properly grounded.
If you are not sure, have a registered electrician check the receptacle.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications:
EHVS-80CS
Stock Number................................................................................................................................ 708448
Fence ....................................................................................................................................... 4”H x 24”L
Abrasive Belt Size ................................................................................................................... 6”W x 89”L
Dust Chute Diameter ..............................................................................................................................4”
Extension Table Size........................................................................................................... 9-7/8 x 11-7/8
Table Size ............................................................................................................................... 32”L x 7”W
Table Tilt ..............................................................................................................................................90°
Motor (UL Listed).................................................................................................................1-1/2 HP,1 Ph
.............................................................................................................................115/230V, prewired 115
Belt Speed (SPFM)........................................................................................................................... 3,900
Overall Dimensions ................................................................................................. 51”L x 26.5”W x 20”H
Net Weight (approx.) .....................................................................................................................256 lbs.
Shipping Weight (approx.) .............................................................................................................262 lbs.
Table of Contents
Warranty .................................................................................................................................................2
Warning...................................................................................................................................................3
Grounding Instructions.............................................................................................................................4
115V Operation .......................................................................................................................................4
230V Operation .......................................................................................................................................5
Specifications..........................................................................................................................................6
Table of Contents ....................................................................................................................................6
Contents of the Shipping Container .........................................................................................................7
Tools Needed for Assembly.....................................................................................................................7
Assembly..............................................................................................................................................8-9
Horizontal Sanding ................................................................................................................................10
Vertical Sanding ....................................................................................................................................10
Contour Sanding....................................................................................................................................10
Sanding Platen Angle Adjustment..........................................................................................................10
Platen Lock Tension Adjustment............................................................................................................11
Changing the Sanding Belt ....................................................................................................................11
Belt Tracking Adjustment..................................................................................................................11-12
Motor Mount Tracking Adjustment .........................................................................................................12
Table Adjustment...................................................................................................................................13
Troubleshooting.....................................................................................................................................13
Parts Breakdowns and Parts Lists.....................................................................................................14-18
Wiring Diagram .....................................................................................................................................19
The specifications in this manual are given as general information and are not binding. JET Equipment
& Tools reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of the Shipping Container
1. Stand (front)
1. Stand (rear)
2. Stand (sides)
1. Extension Table Assembly
1. Extension Cover
1. Owner’s Manual
1. Warranty Card
1. Sanding Unit with Motor
1. Back Stop
1. Handle
1. Driver Wrench
1. Miter Gauge Assembly
1. Sanding Belt
1. Adjusting Wrench
1. Assembly Hardware:
Cabinet
1. Lock Knob (20mm Length)
2. Lock Knob (12mm Length)
1. Lock Knob (35mm Length)
4. Cabinet Pads
4. 5/16” x 5/8” Screws
22. 5/16” Flat Washers
12. 5/16” Hex Nuts
8. 5/16” x 5/8” Hex Cap Bolts
2. 5/16” x 1-1/4” Hex Cap Bolts
4. Larger O/D 5/16” Flat Washers
10. 5/16” Lock Washers
Extension Table
5. 1/4" x 5/8” Hex Cap Bolts
5. 1/4" Flat Washers
5. 1/4” Lock Washers
1. Bracket
1. 3mm Hex Wrench
Dust Chute
3. Pan Head Screws
Tools Needed for Assembly
2) 12mm Wrench or sockets
1) 10mm Wrench or sockets
1) Flat Head Screw Driver
1) Cross Point Screw Driver
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
1. Remove all contents from the shipping
container.
2. Clean all rust protected surfaces with a mild
solvent. Do not use paint or lacquer thinner,
gasoline, or mineral spirits; these will
damage painted surfaces.
3. Attach the four rubber pads (A, Fig. 1) to the
bottoms of the side panels with four 5/16” x
5/8” Screws, four 5/16” flat washers and four
5/16” hex nuts (B, Fig. 1). The hardware
can be found in the bag with the rubber
pads.
4. Attach the side panels (C, Fig. 1) to the front
panel (D, Fig. 1) with four 5/16” x 5/8” hex
cap bolts, eight 5/16” flat washers, four 5/16”
lock washers, and four 5/16” hex nuts (E,
Fig. 1). Hand tighten the hardware at this
point.
Note: Assemble the stand up side down to
make sure that the tops of the panels are
flush.
5. Mount the shelf (F, Fig. 1) to the inside of
the stand with two M5x10 pan head screws
and two M5 lock washers (G, Fig. 1).
6. Finish stand assembly by attaching rear
panel to side panels with four 5/16” x 5/8”
hex cap bolts, eight 5/16” flat washers, four
5/16” lock washers, and four 5/16” hex nuts.
7. Make sure stand is sitting evenly on a level
surface before tightening hardware.
WARNING
Main unit is heavy! Use great care and
adequate resources when lifting the unit up
onto the stand!
Failure to comply may cause serious injury
and/or damage to the sander and/or
property!
8. With the aid of another person, carefully lift
the main unit out of the shipping box, and
up onto the stand. Line up threaded holes
in sander base with holes in stand.
9. Through the door in the cabinet attach main
unit to stand with two 5/16” x 1-1/4” hex cap
bolts, two 5/16” lock washers and two 5/16”
flat washers.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Sanding platen is presently in a horizontal
position. Pull lock handle forward (A, Fig. 3)
to unlock platen assembly, tilt sanding
platen to the vertical position, and push lock
handle to lock platen assembly in place.
Note: do not turn lock handle. Turning or
rotating the lock handle will change the
tension of the locking assembly. This may
cause the locking assembly not to work;
making it necessary for adjustment before
using the machine.
21. Reinstall the guards and secure in place
with lock knobs.
22. Attach the extension cover (D, Fig. 6) with
three pan head screws and one lock knob.
11. Remove the belt guards by unscrewing two
lock knobs (A, Fig. 4). Take out sanding
belt and fence from behind the belt guard.
12. Place handle (B, Fig. 4) on belt tensioning
shaft. Take tension off the mechanism by
moving the handle to the left.
13. Make sure that direction arrow on belt
matches direction indicator on the belt
cover.
14. Place belt on both rollers so that the edge of
the belt is even with the edge of the rollers.
15. Tension the belt by moving the tension
handle lever (B, Fig. 4) to the right. Rotate
the belt by hand in the direction indicated by
the arrow on the belt guard. If belt tracking
needs adjustment, see “Belt Tracking
Adjustment” pages 11-12.
16. Attach the extension bracket (A, Fig. 5)
using three hex cap bolts, three lock
washers and three flat washers (B, Fig. 5).
The hardware can be found in the bag with
the 3mm Hex Wrench.
17. Fasten the extension table (C, Fig. 5) to the
support rod (D, Fig. 5) by tightening the hex
cap screw (E, Fig. 5) against the flat on the
support rod. Tighten the jam nut.
18. Raise the table to a good height and tighten
two set screws on the bracket.
19. Mount the small bracket between the
backside of the extension bracket and the
sander using two hex cap bolts, two lock
washers and two flat washers.
20. Connect the sander to the power source,
turn on the power to the machine just
enough to start the belt rotating and then
turn off. Do this several times and observe
belt tracking. The belt should not wander up
or down. It should be centered between the
two belt rollers. If adjust is necessary refer
to “Belt Tracking Adjustment” pages 11-12.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Removing the belt guard exposes more of
the sanding belt! Replace the belt guards
immediately after completing any sanding
that requires it’s removal!
Failure to comply may cause serious injury!
Horizontal Sanding
With the sanding platen locked in the horizontal
position, the removable fence (A, Fig. 6) may be
used. The fence can be secured in place by
screwing two lock knobs (B, Fig. 6) into the
guide blocks found in the miter slot. Adjust the
table so the fence is at a good height, see
“Table Adjustment” page 13..
The backstop (C, Fig. 6) can also be used by
removing the extension cover (D, Fig. 6) and
placing the backstop pin in the positioning hole
and securing in place with the lock knob. The
extension cover can be reinstalled.
Vertical Sanding
With the sanding platen locked in the vertical
position, the backstop (A, Fig. 7) and/or the
miter gauge (B, Fig. 7) may be used.
If you need to do precise 90° work use a square
between the table and sanding platen. Adjust
for square.
Contour Sanding
The use of extension table (C, Fig. 7) is optional
according to the particular function of the
sanding operation.
The end guard should
always be in place if the extension table is not
being used.
Sanding Platen Angle Adjustment
1. Disconnect the machine from the power
source.
2. Pull handle (A, Fig. 8) forward to release
tension.
3. Move sanding platen to desired position and
hold while locking handle.
4. Use a combination square between the
table and sanding platen to get precise
angles.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Platen Lock Tension Adjustment
1. Disconnect the machine from the power
source.
2. Loosen lock handle by pulling forward (A,
Fig. 9) and move motor and sanding table
toward the horizontal position. Do not lock.
3. Tension eccentric block by tightening the
nyloc nut (B, Fig. 9) with a 14mm wrench.
Turn the nut in ¼ turn increments and test
locking handle for proper tension. Locking
handle is properly tensioned when it
requires positive force to move the
eccentric block (attached to the locking
handle) from one side to the other. The
platen and motor assembly must stay in a
locked position without sliding once the
handle has been moved to the locked
position. Re-adjust as necessary.
Changing the Sanding Belt
1. Disconnect the machine from the power
source.
2. Lock sanding platen in the vertical position.
3. Release tension on the belt by pushing
handle (A, Fig. 10) to the left (as the
operator faces the machine).
4. Remove belt guards.
5. Carefully remove old belt.
Observe
direction arrow on inside of sanding belt.
Make sure that direction arrow on belt
matches direction indicator on the belt
cover. Install new belt over both rollers and
line up edge of belt with edge of rollers.
6. Tension belt by pushing handle to the right.
7. Reinstall the belt guards
Note: Belts stretch with wear. You may have to
adjust tracking with a new belt.
Belt Tracking Adjustment
1. Disconnect the machine from the power
source.
2. Push the belt by hand in the direction
indicated on the belt cover. Observe the
belt position on the rollers. Edge of belt
should remain even with the edge of the
rollers.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Insert the driver with the round shaft,
supplied with the machine into the micro
adjusting nut (A, Fig. 11) and turn away
from you to loosen.
4. Turn the micro adjusting screw (B, Fig. 11)
in ¼ turn increments until the belt tracks
evenly on the rollers when rotated by hand.
5. Tighten the micro adjusting nut (A, Fig. 11).
6. Connect the machine to power.
7. Turn on the power to the machine just
enough to start the belt rotating and then
turn off. Do this several times and observe
belt tracking. Adjust as necessary. If the
tracking cannot be corrected goto the next
section “Motor Mount Tracking Adjustment”.
Motor Mount Tracking Adjustment
The EHVS-80CS comes with tracking
adjustment bolts (A, Fig. 12) on the motor
plate. These are set at the factory and should
not require any further adjustment. If, however,
you are not able to track the belt using the belt
tracking adjustment assembly on the sanding
platen, the motor mount bolts will have to be
adjusted:
1. Disconnect the machine from the power
source.
2. Slightly loosen the four motor mount nuts
(B, Fig. 12) just enough so the tracking bolts
can make an adjustment.
3. Loosen both locking hex nuts.
4. Turn one bolt (A, Fig. 12) a ¼ turn and
rotate the sanding belt by hand to observe
which direction the belt is tracking. If it is
traveling in the direction needed to correctly
track the belt, tighten both locking nuts and
fine tune the tracking with the belt tracking
assembly on the platen.
5. If the belt starts to travel in the wrong
direction, back off a quarter turn and tighten
the other bolt a quarter turn. This should
start the belt in the proper direction.
Note: Use the motor mount bolts as a “major”
tracking adjustment.
Use the belt tracking
assembly on the sanding plates as a “fine”
tracking adjustment.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Adjustment
WARNING
Do not position table below sanding belt!
Keep an overlap of at least 1/16” between
table and sanding belt to avoid material
and/or fingers getting caught!
Failure to comply may cause serious injury!
1. Loosen two lock knobs (A, Fig. 13).
2. Raise or lower work table to desired level.
3. Tighten two lock knobs.
Troubleshooting
Trouble
Possible Cause
Solution
1. Sander unplugged from wall
or motor
1. Check all plug connections
2. Replace fuse or reset circuit
breaker
2. Fuse blown or circuit breaker
tripped
Sander will not start
3. Replace cord
3. Cord damaged
1. Replace with adequate size
and length cord
1. Extension cord too light or
too long
Sanding belt does not come
up to speed
2. Refer to motor junction cover
for proper wiring
2. Motor not wired for proper
voltage
3. Contact a qualified
electrician
3. Low current
1. Stand on uneven floor
2. Motor mounts are loose
1. Adjust stand so that it rests
evenly on the floor
Machine vibrates excessively
2. Tighten motor mount bolts
3. Repalce spring
3. Tension spring is worn or
broken
1. Arrow on the sanding belt
and machine should be
pointing in the same
direction.
1. Belt is running in the wrong
direction
Abrasive belt keeps tearing
Sanded edge not square
1. Table not square to sanding
platen
1. Use a square to adjust table
to sanding platen
1. Keep workpiece moving
2. Use coarser grit for stock
removal and fine grit for
finish sanding.
1. Work held still
2. Wrong grit sanding belt
3. Feed pressure too great
4. Sanding against the grain
Sanding marks on wood
3. Never force work into
sanding platen
4. Sand with the grain
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Table and Motor Assembly
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List For The EHVS-80CS Sander
Table and Motor Assembly
Index Part
No. No.
Description
Size
Qty.
1..........EHVS80CS-01 ................. Base.............................................................. .................................1
2..........994532............................. Switch (serial #: 9031435 and lower) ............. .................................1
............EHVS80-02N ................... Push Button Switch (serial #: 9031436 and higher) .........................1
3..........EHVS80-03-1................... Switch Panel (serial #: 9031435 and lower) ... .................................1
............EHVS80-03N ................... Switch Panel (serial #: 9031436 and higher) .. .................................1
3A........EHVS80-02B.................... Switch Box .................................................... .................................1
4..........EHVS80-04...................... Pan Head Screw............................................ 3/16”x1-1/2”..............3
5..........EHVS80-05A.................... External Tooth Lock Washer ......................... 3/16”.........................3
6..........EHVS80-06...................... Nut ................................................................ 3/16”.........................2
7..........EHVS80-07...................... Nylon Clamp.................................................. .................................2
8..........EHVS80-08...................... Work Table Bracket....................................... .................................1
9A........EHVS80-09A.................... Nut (serial#: 1023018 and higher).................. 3/8”...........................1
............EHVS80-09...................... Locking Collar (serial#: 1013017 and lower) .. .................................1
10A......TS-0561031 ..................... Hex Nut......................................................... 3/8”...........................1
10........EHVS80-10...................... Locking Block................................................ .................................1
11........EHVS80-11...................... Spring Pin ..................................................... M4............................1
12........EHVS80-12...................... Lock Handle .................................................. .................................1
13........10102023A....................... Knob.............................................................. .................................1
............EHVS80-12A.................... Lock Handle Assembly (#12,13) .................... .................................1
14........S0430525......................... Key................................................................ 5x5x25 .....................1
15........EHVS80-15...................... Hex Cap Bolt................................................. 1/4”x3/4”...................1
16........TS-0561011 ..................... Washer.......................................................... 1/4”...........................1
17........EHVS80-17...................... Table............................................................. .................................1
17A......EHVS80-17A.................... Hex Cap Bolt ................................................ 5/16”x5/8”.................4
18........EHVS80-18...................... Screw............................................................ M10..........................2
19........TS-1540073 ..................... Hex Nut......................................................... M10..........................2
19A......TS-0720091 ..................... Lock Washer ................................................. 3/8”...........................2
20........EHVS80-20...................... Guide Block................................................... .................................2
21........EHVS80-21...................... Fence............................................................ .................................1
22........EHVS80-22A.................... JETKnob (serial#: 1023018 and higher)......... M8x12mm ................3
............EHVS80-22B.................... Knob (serial#: 1013017 and lower)................. M8x12mm ................3
23........EHVS80-23...................... Motor Roller................................................... .................................1
24........EHVS80-24...................... Guide Bar...................................................... .................................1
25........S0310306......................... Pin................................................................. M3............................1
26........EHVS80-26...................... Set Screw...................................................... 1/4”x1/4”...................1
27........EHVS80-27...................... Location Plate ............................................... .................................1
28........EHVS80-28...................... Pointer........................................................... .................................1
28A......EHVS80-28A.................... Locating Block............................................... .................................1
29........see page 17 ..................... Sanding Belt.................................................. 6”x89”.......................1
30........10104046......................... Miter Gauage Body........................................ .................................1
............EHVS80-MG .................... Miter Gauge Assembly .................................. ...................................
31........S0030108......................... Round Head Screw........................................ 5/32”x5/8”.................3
32........EHVS80-32...................... Nut ................................................................ 5/32”.........................3
33........EHVS80-33...................... Knob.............................................................. .................................1
34........20101048......................... Platen............................................................ .................................1
34G .....EHVS80-34G ................... Graphite ........................................................ .................................1
34B......EHVS80-34B.................... Side Plate...................................................... .................................1
............TS-0051061 ..................... Hex Cap Bolt (motor plate – not shown) ........ 5/16”x1-1/4”..............2
............TS-0561021 ..................... Hex Nut (motor plate – not shown) ............... 5/16”.........................2
35........EHVS80-35...................... Tension Bar................................................... .................................1
36........EHVS80-36A.................... JET Knob ...................................................... M8x35mm ................1
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Index Part
No. No.
Description
Size
Qty.
37A......EHVS80-37A.................... Pin................................................................. M6x40mm ................1
38........EHVS80-38...................... Spring............................................................ .................................1
39........EHVS80-39A.................... Spacer........................................................... .................................1
40........EHVS80-40...................... Hex Cap Bolt................................................. 5/16”x5/16” ...............1
41........EHVS80-41...................... Roller Arm..................................................... .................................1
42........EHVS80-42...................... Shaft ............................................................. .................................1
43........EHVS80-43...................... Nut ................................................................ 1/4”...........................1
43B......TS-0267051 ..................... Set Screw...................................................... .................................1
44........BB-6004ZZ ...................... Ball Bearing................................................... 6004ZZ.....................2
45........EHVS80-45...................... Driven Roller ................................................. .................................1
46........EHVS80-46...................... Spring Ring ................................................... STW-19....................1
47........EHVS80-47...................... Mico-Adjusting Screw.................................... .................................1
47A......EHVS80-47A.................... Mico-Adjusting Nut ........................................ .................................1
48........EHVS80-48...................... Protective Cover ........................................... .................................1
49........S0030304......................... Round Head Screw........................................ 3/16”x3/8”.................4
50........EHVS80-50...................... Star Washer .................................................. 3/16”.......................15
51........EHVS80-51...................... Belt Tensioning Arm ...................................... .................................1
54........EHVS80-54...................... Handle........................................................... .................................1
55........TS-0051081 ..................... Hex Cap Bolt................................................. 5/16”X1-3/4”..............1
56........TS-0561021 ..................... Hex Nut......................................................... 5/16”.........................1
57........EHVS80-57...................... Tilt Scale....................................................... .................................1
58........EHVS80-58...................... Hex Socket Screw ........................................ 3/16”x3/8”.................1
59........EHVS80-59...................... Pointer........................................................... .................................1
60........EHVS80-60...................... Screw............................................................ 3/16”x1/4”.................1
61........EHVS80-61...................... Motor............................................................. .................................1
62........TS-0051061 ..................... Hex Cap Bolt................................................. 5/16”x1-1/4”..............2
63........TS-0680031 ..................... Washer.......................................................... 5/16”.......................26
64........TS-0720081 ..................... Lock Washer ................................................. 5/16”.........................8
65........TS-0561021 ..................... Hex Nut......................................................... 5/16”.........................6
67........EHVS80-67...................... Motor Cord .................................................... .................................1
68........EHVS80-68...................... Power Cord ................................................... .................................1
69........EHVS80-69...................... Belt Cover ..................................................... .................................1
69A......EHVS80-69A.................... Belt Cover (smaller) ...................................... .................................1
70........EHVS80-70A.................... Up-Down Plate .............................................. .................................2
71........EHVS80-71A.................... JET Knob ...................................................... M8x20mm ................4
72........EHVS80-72...................... Backstop ....................................................... .................................1
81........EHVS80-81...................... Driver Wrench............................................... .................................1
82........EHVS80-82...................... Flat Head Screw............................................ 3/16”x1/2”.................8
91........TS-0680021 ..................... Flat Washer................................................... 1/4”...........................6
92........TS-0720071 ..................... Lock Washer ................................................. 1/4”...........................6
93........EHVS80-93...................... Screw............................................................ M6x16mm ................1
94........EHVS80-94...................... Extension Table ............................................ .................................1
96........EHVS80-96...................... Supporting Rod ............................................. .................................1
97........EHVS80-97...................... Mounting Bracket .......................................... .................................1
98........EHVS80-98A.................... Bracket (serial#: 1023018 and higher) ........... .................................1
............EHVS80-98...................... Bracket (serial#: 1013017 and lower)............. .................................1
99........TS-0050031 ..................... Hex Cap Bolt................................................. 1/4”x3/4”...................5
103......EHVS80-103.................... Hex Wrench .................................................. 3mm.........................1
102......TS-0267041 ..................... Set Screw...................................................... 1/4”x3/8”...................2
105......EHVS80-57A.................... Scale Label ................................................... .................................1
106......EHVS80CS-106 ............... I.D Label........................................................ .................................1
107......EHVS80-107.................... Warning Label............................................... .................................1
108......EHVS80-108.................... Label ............................................................. .................................1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Index Part
No. No.
Description
Size
Qty.
109......EHVS80-109.................... Label ............................................................. .................................1
110......EHVS80-110.................... Pan Hand Screw ........................................... 3/16”x3/8”.................3
111......EHVS80-111.................... Extension Cover............................................ .................................1
112......EHVS80-112.................... Washer.......................................................... 1/4”...........................1
113......EHVS80CS-113 ............... Protecting Rubber.......................................... .................................2
114......TS-0680031 ..................... Washer.......................................................... 5/6”x23Dx2t..............2
120......EHVS80CS-120 ............... Fiber Washer................................................. 5/16”.........................1
............EHVS80-AT ..................... Adjusting Tool (not show) .............................. .................................1
............EHVS80-HK..................... Hardware Kit (not show) ................................ .................................1
............EHVS80-MG .................... Miter Gauge Assembly Complete ................. .................................1
Sanding Belts
40 Grit Open Coat ........................ 57422810
60 Grit Open Coat ........................ 57422910
80 Grit Open Coat ........................ 57423010
100 Grit Open Coat ...................... 57423110
120 Grit Open Coat ...................... 57423210
150 Grit Open Coat ...................... 57423310
180 Grit Open Coat ...................... 57423410
40 Grit Closed Coat ...................... 57618210
60 Grit Closed Coat ...................... 57618410
80 Grit Closed Coat ...................... 57618510
100 Grit Closed Coat .................... 57618610
120 Grit Closed Coat .................... 57618710
150 Grit Closed Coat .................... 57512410
180 Grit Closed Coat .................... 57512510
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Stand Assembly
Index Part
No. No.
Description
Size
Qty.
1..........TS-0680031 ..................... Flat Washer................................................... 5/16”.........................22
2..........TS-0720081 ..................... Lock Washer ................................................. 5/16”.........................10
3..........TS-0561021 ..................... Hex Nut......................................................... 5/16”...........................8
4..........EHVS80CS-S04............... Side Panel..................................................... ...................................2
5..........EHVS80CS-S05............... Pad ............................................................... ...................................4
6..........EHVS80CS-S06............... Screw............................................................ 5/16”x5/8”...................4
7..........EHVS80CS-S07............... Rear Panel .................................................... ...................................1
8..........TS-0561021 ..................... Hex Nut......................................................... 5/16”...........................4
9..........TS-0081031 ..................... Hex Cap Bolt................................................. 5/16”-3/4”..................10
10........EHVS80CS-S10............... Pan Head Screw............................................ M5x10 ........................2
11........EHVS80CS-S11............... Door .............................................................. ...................................1
12........EHVS80CS-S12............... Shelf.............................................................. ...................................1
13........EHVS80CS-S13............... Latch Assembly............................................. ...................................1
14........TS-1551031 ..................... Lock Washer ................................................. M5..............................2
15........EHVS80CS-S15............... Front Panel (w/door)...................................... ...................................1
16........EHVS80CS-S16............... Pan Head Screw............................................ ...................................2
17........EHVS80CS-S17............... JET Label...................................................... ...................................1
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|