This Manual is Bookmarked
Operating Instructions
ZX Series Lathes
Models GH-1440ZX/1460ZX
GH-1640ZX/1660ZX
GH-1840ZX/1860ZX/1880ZX
GH-2280ZX
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Ph.: 800-274-6848
Part No. M-321910
Revision G 11/05
Copyright © WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty and Service ..............................................................................................................................2
Table of Contents ....................................................................................................................................3
Warning...................................................................................................................................................4
Specifications ..........................................................................................................................................6
Specifications ..........................................................................................................................................7
Specifications ..........................................................................................................................................8
Specifications ..........................................................................................................................................9
Unpacking .............................................................................................................................................10
Contents of the Shipping Container ....................................................................................................10
Uncrating and Cleanup ..........................................................................................................................11
Chuck Preparation (Three Jaw)..........................................................................................................11
Lubrication .........................................................................................................................................12
Coolant Preparation ...........................................................................................................................13
Electrical Connections ...........................................................................................................................13
Conversion to 460 Volt Operation.......................................................................................................14
General Description...............................................................................................................................14
Lathe Bed ..........................................................................................................................................14
Headstock..........................................................................................................................................14
Carriage.............................................................................................................................................15
Four Way Tool Post............................................................................................................................15
Apron.................................................................................................................................................15
Tailstock.............................................................................................................................................15
Leadscrew and Feed Rod...................................................................................................................15
Feed Gearbox ....................................................................................................................................15
Steady Rest .......................................................................................................................................15
Follow Rest ........................................................................................................................................16
Controls.................................................................................................................................................16
Operation...............................................................................................................................................19
Feed and Thread Selection ................................................................................................................19
Thread Cutting ...................................................................................................................................19
Gib Adjustments.................................................................................................................................19
Tailstock Off-Set.................................................................................................................................19
Removing Gap Section.......................................................................................................................20
Installing Removable Gap Section......................................................................................................20
Belt Replacement and Adjustment......................................................................................................20
Aligning Tailstock to Headstock..........................................................................................................20
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
1. Read and understand the entire owners manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This lathe is designed and intended for use by properly trained and experienced personnel only. If
you are not familiar with the proper and safe operation of a lathe, do not use until proper training and
knowledge have been obtained.
5. Do not use this lathe for other than its intended use. If used for other purposes, WMH Tool Group
disclaims any real or implied warranty and holds itself harmless from any injury that may result from
that use.
6. Always wear approved safety glasses/face shields while using this lathe. Everyday eyeglasses only
have impact resistant lenses; they are not safety glasses.
7. Before operating this lathe, remove tie, rings, watches and other jewelry, and roll sleeves up past the
elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are
recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
•
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
17. Provide for adequate space surrounding work area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area. Keep children away.
20. Make your workshop child proof with padlocks, master switches or by removing starter keys.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
22. Maintain a balanced stance at all times so that you do not fall or lean against moving parts. Do not
overreach or use excessive force to perform any machine operation. Never force the cutting action.
23. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
24. Use recommended accessories; improper accessories may be hazardous.
25. Maintain tools with care. Keep cutting tools sharp and clean for the best and safest performance.
Follow instructions for lubricating and changing accessories.
26. Do not attempt to adjust or remove tools during operation.
27. Turn off the machine and disconnect from power before cleaning. Use a brush to remove shavings or
debris — do not use your hands.
28. Do not stand on the machine. Serious injury could occur if the machine tips over.
29. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
30. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
- - SAVE THESE INSTRUCTIONS - -
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The following specifications were current at the time this manual was published, but because of our policy
of continuous improvement, WMH Tool Group reserves the right to change specifications at any time and
without prior notice, without incurring obligations.
Specifications
Model Number...................................................................... GH-1440ZX .............................. GH-1460ZX
Stock Number.............................................................................. 321910 ..................................... 321920
Capacities:
Swing over Bed (in.).............................................................................14 .............................................14
Swing over Cross Slide (in.).............................................................7-5/8 .........................................7-5/8
Swing Through Gap (in.)................................................................23-5/8 .......................................23-5/8
Length of Gap (in.).........................................................................12-1/4 .......................................12-1/4
Distance between Centers (in.)............................................................40 .............................................60
Headstock:
Spindle Bore (in.).............................................................................3-1/8 .........................................3-1/8
Spindle Mount.................................................................................. D1-8 ......................................... D1-8
Spindle Taper with Sleeve .................................................... MT-7(MT-5) .............................. MT-7(MT-5)
Number of Spindle Speeds ..................................................................12 .............................................12
Range of Spindle Speeds (RPM) ............................................ 42 to 1800 ................................ 42 to 1800
Gearbox:
Number of Longitudinal and Cross Feeds ..........................................122 ...........................................122
Range of Longitudinal Feeds (in./rev.)............................0.0015 to 0.0913 .......................0.0015 to 0.0913
Range of Cross Feeds (in./rev.) .....................................0.0006 to 0.0365 .......................0.0006 to 0.0365
Number of Inch Threads ......................................................................61 .............................................61
Range of Inch Threads (in.)..................................................... 1-5/8 to 72 ................................ 1-5/8 to 72
Number of Metric Threads ...................................................................24 .............................................24
Range of Metric Threads (mm)................................................. 0.05 to 20 ................................. 0.05 to 20
Compound and Carriage:
Maximum Tool Size (in.) .................................................................. 1 x 1 ......................................... 1 x 1
Maximum Compound Slide Travel (in.).............................................5-1/8 .........................................5-1/8
Maximum Cross Slide Travel (in.) ..........................................................9 ...............................................9
Carriage Travel (in.).............................................................................35 .............................................55
Tailstock:
Tailstock Spindle Travel (in.)..................................................................5 ...............................................5
Tailstock Taper................................................................................MT-4 .........................................MT-4
Steady Rest Capacity (in.) ..................................................... 1/2 to 3-1/2 ............................... 1/2 to 3-1/2
Follow Rest Capacity (in.) ............................................................ 3/8 to 7 ..................................... 3/8 to 7
Width of Bed (in.)...........................................................................13-3/8 .......................................13-3/8
Overall Dimensions (in.)(LxWxH) ..............................97-1/2 x 40 x 46-7/8 ................116-1/2 x 40 x 46-7/8
Motor................................................................7-1/2HP, 3Ph, 230/460V* ..........7-1/2HP, 3Ph, 230/460V*
Approximate Net Weight (lbs.) .........................................................5187 ......................................... 5380
*pre-wired 230V
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model Number...................................................................... GH-1640ZX .............................. GH-1660ZX
Stock Number.............................................................................. 321930 ..................................... 321940
Capacities:
Swing over Bed (in.).............................................................................16 .............................................16
Swing over Cross Slide (in.).................................................................10 .............................................10
Swing Through Gap (in.)................................................................25-7/8 .......................................25-7/8
Length of Gap (in.).........................................................................12-1/4 .......................................12-1/4
Distance between Centers (in.)............................................................40 .............................................60
Headstock:
Spindle Bore (in.).............................................................................3-1/8 .........................................3-1/8
Spindle Mount.................................................................................. D1-8 ......................................... D1-8
Spindle Taper with Sleeve .................................................... MT-7(MT-5) .............................. MT-7(MT-5)
Number of Spindle Speeds ..................................................................12 .............................................12
Range of Spindle Speeds (RPM) ............................................ 25 to 1800 ................................ 25 to 1800
Gearbox:
Number of Longitudinal and Cross Feeds ..........................................122 ...........................................122
Range of Longitudinal Feeds (in./rev.)............................0.0015 to 0.0913 .......................0.0015 to 0.0913
Range of Cross Feeds (in./rev.) .....................................0.0006 to 0.0365 .......................0.0006 to 0.0365
Number of Inch Threads ......................................................................61 .............................................61
Range of Inch Threads (in.)..................................................... 1-5/8 to 72 ................................ 1-5/8 to 72
Number of Metric Threads ...................................................................24 .............................................24
Range of Metric Threads (mm)................................................. 0.05 to 20 ................................. 0.05 to 20
Compound and Carriage:
Maximum Tool Size (in.) .................................................................. 1 x 1 ......................................... 1 x 1
Maximum Compound Slide Travel (in.).............................................5-1/8 .........................................5-1/8
Maximum Cross Slide Travel (in.) ..........................................................9 ...............................................9
Carriage Travel (in.).............................................................................35 .............................................55
Tailstock:
Tailstock Spindle Travel (in.)..................................................................5 ...............................................5
Tailstock Taper................................................................................MT-4 .........................................MT-4
Steady Rest Capacity (in.) ..................................................... 1/2 to 3-1/2 ............................... 1/2 to 3-1/2
Follow Rest Capacity (in.) ............................................................ 3/8 to 7 ..................................... 3/8 to 7
Width of Bed (in.)...........................................................................13-3/8 .......................................13-3/8
Overall Dimensions (in.)(LxWxH) ....................................97-1/2 x 40 x 48 ......................116-1/2 x 40 x 48
Motor................................................................7-1/2HP, 3Ph, 230/460V* ..........7-1/2HP, 3Ph, 230/460V*
Approximate Net Weight (lbs.) .........................................................5475 ......................................... 5795
*pre-wired 230V
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model Number....................................................GH-1840ZX...............GH-1860ZX............... GH-1880ZX
Stock Number........................................................... 321950 ......................321960...................... 321970
Capacities:
Swing over Bed (in.).......................................................... 18..............................18..............................18
Swing over Cross Slide (in.).............................................. 11..............................11..............................11
Swing Through Gap (in.)............................................. 27-1/2........................27-1/2........................27-1/2
Length of Gap (in.)...................................................... 12-1/4........................12-1/4........................12-1/4
Distance between Centers (in.)......................................... 40..............................60..............................80
Headstock:
Spindle Bore (in.).......................................................... 3-1/8..........................3-1/8..........................3-1/8
Spindle Mount................................................................D1-8..........................D1-8.......................... D1-8
Spindle Taper with Sleeve ..................................MT-7(MT-5)...............MT-7(MT-5)............... MT-7(MT-5)
Number of Spindle Speeds ............................................... 12..............................12..............................12
Range of Spindle Speeds (RPM) ..........................25 to 1800.................25 to 1800................. 25 to 1800
Gearbox:
Number of Longitudinal and Cross Feeds ....................... 122............................122............................ 122
Range of Longitudinal Feeds (in./rev.).........0.0015 to 0.0913....... 0.0015 to 0.0913........0.0015 to 0.0913
Range of Cross Feeds (in./rev.) ..................0.0006 to 0.0365....... 0.0006 to 0.0365........0.0006 to 0.0365
Number of Inch Threads ................................................... 61..............................61..............................61
Range of Inch Threads (in.).................................. 1-5/8 to 72.................1-5/8 to 72................. 1-5/8 to 72
Number of Metric Threads ................................................ 24..............................24..............................24
Range of Metric Threads (mm)...............................0.05 to 20..................0.05 to 20.................. 0.05 to 20
Compound and Carriage:
Maximum Tool Size (in.) ................................................1 x 1..........................1 x 1.......................... 1 x 1
Maximum Compound Slide Travel (in.).......................... 5-1/8..........................5-1/8..........................5-1/8
Maximum Cross Slide Travel (in.) ....................................... 9................................9................................9
Carriage Travel (in.).......................................................... 35..............................55..............................75
Tailstock:
Tailstock Spindle Travel (in.)............................................... 5................................5................................5
Tailstock Taper.............................................................MT-5......................... MT-5..........................MT-5
Steady Rest Capacity (in.) .................................. 1/2 to 3-1/2................1/2 to 3-1/2................ 1/2 to 3-1/2
Follow Rest Capacity (in.) ......................................... 3/8 to 7......................3/8 to 7...................... 3/8 to 7
Width of Bed (in.)........................................................ 13-3/8........................13-3/8........................13-3/8
Overall Dimensions (in.)(LxWxH) ...............97-1/2x40x48-7/8.....116-1/2x40x48-7/8.....136-1/8x40x48-7/8
Motor............................................................... 7-1/2HP, 3Ph.............7-1/2HP, 3Ph.............7-1/2HP, 3Ph
.............................................................................230/460V* ................. 230/460V*..................230/460V*
Approximate Net Weight (lbs.) ...................................... 5980 ..........................6245.......................... 6590
*pre-wired 230V
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model Number........................................................................................................................ GH-2280ZX
Stock Number................................................................................................................................ 321980
Capacities:
Swing over Bed (in.)...............................................................................................................................22
Swing over Cross Slide (in.)...................................................................................................................11
Swing Through Gap (in.)..................................................................................................................27-1/2
Length of Gap (in.)...........................................................................................................................12-1/4
Distance between Centers (in.)..............................................................................................................80
Headstock:
Spindle Bore (in.)...............................................................................................................................3-1/8
Spindle Mount.................................................................................................................................... D1-8
Spindle Taper with Sleeve ...................................................................................................... MT-7(MT-5)
Number of Spindle Speeds ....................................................................................................................12
Range of Spindle Speeds (RPM) .............................................................................................. 25 to 1800
Gearbox:
Number of Longitudinal and Cross Feeds ............................................................................................122
Range of Longitudinal Feeds (in./rev.)..............................................................................0.0015 to 0.0913
Range of Cross Feeds (in./rev.) .......................................................................................0.0006 to 0.0365
Number of Inch Threads ........................................................................................................................61
Range of Inch Threads (in.)....................................................................................................... 1-5/8 to 72
Number of Metric Threads .....................................................................................................................24
Range of Metric Threads (mm)................................................................................................... 0.05 to 20
Compound and Carriage:
Maximum Tool Size (in.) .................................................................................................................... 1 x 1
Maximum Compound Slide Travel (in.)...............................................................................................5-1/8
Maximum Cross Slide Travel (in.) ............................................................................................................9
Carriage Travel (in.)...............................................................................................................................75
Tailstock:
Tailstock Spindle Travel (in.)....................................................................................................................5
Tailstock Taper..................................................................................................................................MT-5
Steady Rest Capacity (in.) ....................................................................................................... 1/2 to 3-1/2
Follow Rest Capacity (in.) .............................................................................................................. 3/8 to 7
Width of Bed (in.).............................................................................................................................13-3/8
Overall Dimensions (in.)(LxWxH) ..............................................................................136-1/8 x 40 x 48-7/8
Motor......................................................................................... 10HP, 3PH, 230V/460V (pre-wired 230V)
Approximate Net Weight (lbs.) ........................................................................................................... 7400
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Tool Box containing:
Unpacking
1
1
1
1
6
6
1
1
1
1
1
1
1
1
2
1
Box Wrench Set
Hex Wrench Set
Spindle Sleeve
Open shipping container and check for shipping
damage. Report any damage immediately to
your distributor and shipping agent. Do not
discard any shipping material until the Lathe is
assembled and running properly.
Center
Leveling Bolts
Leveling Pads
Compare the contents of your container with the
following parts list to make sure all parts are
intact. Missing parts, if any, should be reported
to your distributor. Read the instruction manual
thoroughly for assembly, maintenance and
safety instructions.
Flat Blade Screwdriver
Cross Point Screwdriver
Chuck Wrench
Tool Post Wrench
Light Bulb
Adjustable Wrench
Oil Gun
Contents of the Shipping Container
1
1
1
1
1
1
Lathe
Cross Feed Handle
Shear Pins
Steady Rest (mounted on Lathe)
Follow Rest (mounted on Lathe)
10” Three Jaw Chuck (mounted on Lathe)
12” Four Jaw Chuck
Live Center (MT4 for 14” & 16” lathes;
MT5 for 18” & 22” lathes)
Operating Manual
Parts List Manual
Warranty Card
1
1
1
Face Plate (12” Face Plate for 14” & 16”
lathes; 16” Face Plate for 18” & 22” lathes)
contents of Tool Box
Read and understand the entire contents of this manual before attempting set-up
or operation! Failure to comply may cause serious injury.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Uncrating and Cleanup
1. Finish removing the wooden crate from
around the lathe.
2. Unbolt the lathe from the shipping crate
bottom.
3. Choose a location for the lathe that is dry,
has good lighting, and has enough room to
allow servicing the lathe on all four sides.
4. Sling the lathe as shown in Figure 1, using
steel rods or pipes of sufficient strength
inserted through the holes in the bed
casting. Do not lift lathe by the spindle.
With adequate lifting equipment, slowly
raise the lathe off the shipping crate bottom.
Make sure lathe is balanced before moving.
Figure 1
5. To avoid twisting the bed, the lathe’s
location must be absolutely flat and level.
Check for
a
level condition using
a
machinist’s precision level on the bedways
both front to back and side to side. The
leveling pads included in the tool box and
the leveling screws in the lathe base will
help you to reach a level condition. The
lathe must be level to be accurate.
6. Clean all rust protected surfaces using a
mild commercial solvent, kerosene or diesel
fuel. Do not use paint thinner, gasoline, or
lacquer thinner. These will damage painted
surfaces. Cover all cleaned surfaces with a
light film of 20W machine oil.
7. Open the end gear cover. Clean all
components of the end gear assembly and
coat all gears with a heavy, non-slinging
grease. Close the end gear cover.
Chuck Preparation (Three Jaw)
Read and understand all
directions for chuck preparation. Failure to
comply may cause serious injury and/or
damage to the lathe.
NOTE: Before removing the chuck from the
spindle, place a flat piece of wood (plywood,
etc.) across the bedways under the chuck to
prevent damage to the bedways should the
chuck fall from your hands.
To remove the chuck:
1. Support the chuck while turning six
camlocks 1/4 turn counterclockwise with the
chuck wrench from the tool box.
2. Carefully remove the chuck from the spindle
and place on an adequate work surface.
Figure 2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Inspect the camlock studs. Make sure they
have not become cracked or broken during
transit. Clean all parts thoroughly with
solvent. Also clean the spindle and
camlocks.
4. Cover all chuck jaws and scroll inside the
chuck with #2 lithium tube grease. Cover the
spindle, camlocks, and chuck body with a
light film of 20W oil.
5. Lift the chuck up to the spindle nose and
press onto the spindle. Tighten in place by
turning the camlocks 1/4 turn clockwise. The
index mark (A, Figure 3) on the camlock
should be between the two indicator arrows
when tight (B, Figure 3). If the index mark is
not between the two arrows, remove the
chuck and adjust the camlock studs by
either turning out one full turn (if cams will
not engage) or turning in one full turn (if
cams turn beyond indicator marks.)
Figure 3
6. Install chuck and tighten in place.
Lubrication
Lathe must be serviced at all
lubrication points and all reservoirs filled to
operating level before the lathe is put into
service. Failure to comply may cause serious
damage to the lathe.
1. Headstock – Oil must be up to indicator
mark in oil sight glass (A, Figure 4). Top off
with Mobil DTE® Oil Heavy Medium. Fill by
removing the plug on top of the headstock.
To drain, remove drain plug on the left side
of the headstock at the lower rear corner.
Drain oil completely and clean out all metal
shavings. Refill after the first month of
operation. Then change the oil in the
headstock every two months.
Figure 4
2. Gearbox – Oil must be up to indicator mark
in oil sight glass (B, Figure 4). Top off with
Mobil DTE® Oil Heavy Medium. To add oil
to the gearbox, remove two screws on the
top cover and remove cover. To drain,
remove drain plug (C, Figure 4) on the left
side of the gearbox. Drain oil completely
and refill after the first three months of
operation. Then change oil in the gearbox
every six months.
3. Apron – Oil must be between indicator
marks in the oil sight glass (A, Figure 5).
Top off with Mobil DTE® Oil Heavy Medium.
Remove oil plug (B, Figure 5) to fill. To
drain, remove drain plug on bottom of
apron.
Figure 5
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Drain oil completely and refill after the first
three months of operation. Then, change oil
in the apron annually. Pull knob (C, Figure
5) on the one-shot lube system and hold for
several seconds to allow oil to fill the pump.
When the knob is released, oil will flow
through various oil lines to lubricate the
ways and cross slide surface. Perform this
twice daily or as needed. When the oil level
is below the indicator mark, oil must be
added.
4. Leadscrew and Feed Rod – Lubricate two
ball oilers on the right side bracket (A,
Figure 6) with 30W machine oil daily.
5. Saddle – Daily lubricate ball oiler (A, Figure
7) on handwheel shaft with Mobil DTE® Oil
Heavy Medium.
Figure 6
6. Compound Rest – Daily lubricate two ball
oilers (B, Figure 7) on top of compound slide
with Mobil DTE® Oil Heavy Medium.
7. Cross Slide – Daily lubricate one ball oiler
(C, Figure 7) with Mobil DTE® Oil Heavy
Medium.
8. Tailstock – Daily lubricate one ball oiler (A,
Figure 8) on top of tailstock with Mobil
DTE® Oil Heavy Medium.
Coolant Preparation
Follow
coolant
manu-
facturer’s recommendations for use, care
and disposal.
1. Remove access cover on tailstock end at
the rear base of the lathe. Make sure
coolant pump has not shifted during
transport.
Figure 7
2. Pour four gallons (approximate) of coolant
mix into the chip pan.
3. After machine has been connected to
power, turn on coolant pump and check to
see that coolant is cycling properly.
4. Replace access cover.
Electrical Connections
Figure 8
Electrical connections must
be made by
a
qualified electrician in
compliance with all relevant codes. This
machine must be properly grounded while in
use to help protect the operator from
electrical shock and possible fatal injury.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The main motor is rated at 7-1/2 HP (or 10HP
for model 2280ZX), 230/460V and comes from
the factory prewired at 230V. Confirm that power
available at the lathe’s location is the same
rating as the lathe.
Power is connected properly when rotating the
forward-reverse knob (E, Figure 12) to the left
position causes the spindle to rotate
counterclockwise as viewed from the tailstock. If
the chuck rotates in the clockwise direction,
disconnect the lathe from the power source,
switch any two of the three power leads (not the
green ground wire), and re-connect the lathe to
the power source.
Conversion to 460 Volt Operation
Disconnect machine from
power source. Failure to do so may cause
serious injury.
Main Motor: Change the wires according to the
diagram on the outside of the motor junction
box.
Figure 9
Transformer: Open electrical panel on rear of
machine on the headstock side. Switch wire
from 230V terminal to 460V terminal as outlined
on the transformer.
Coolant Pump: Open access panel on the base
at the tailstock end. Change wires in coolant
pump junction box according to diagram on the
outside of the junction box cover.
Main Power Switch (A, Figure 9): Turns power
to machine on and off.
Power Source Cable Receiver (B, Figure 9).
Make sure the lathe is properly grounded.
General Description
Lathe Bed
Figure 10
The lathe bed (A, Figure 10) is made of cast iron
with low vibration and high rigidity. Two
precision ground v-slideways, reinforced by
induction hardening and grinding, are an
accurate guide for the carriage and headstock.
The main drive motor is mounted in the stand
below the the headstock.
Headstock
The headstock (B, Figure 10) is cast from high
grade, low vibration cast iron. It is bolted to the
bed by four hex socket cap bolts. In the head,
the spindle is mounted on precision taper roller
bearings.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Carriage
The carriage (C, Figure 10) is made from high
quality cast iron. The cross-slide (E, Figure 10)
is mounted on the carriage and moves on a
dovetailed slide which can be adjusted for play
by means of the gibs.
The compound slide (D, Figure 10) which is T-
slotted, and mounted on the cross slide (E,
Figure 10) can be rotated 360°. The compound
slide and the cross slide travel in a dovetailed
slide and have adjustable gibs.
Four Way Tool Post
The four way tool post (F, Figure 10) is mounted
on the compound slide and allows a maximum
of four tools to be mounted at the same time.
Remember to use a minimum of two clamping
screws when installing a cutting tool.
Apron
The apron (G, Figure 10) is mounted to the
carriage. Quick travel of the apron is
accomplished by means of a bed-mounted rack
and pinion, operated by the handwheel on the
front of the apron.
Tailstock
The tailstock (H, Figure 11) slides on a v-way
and can be locked at any location by a clamping
lever. The tailstock has a heavy duty quill with a
Morse Taper #4, or Morse Taper #5 (18” and
22” models).
Figure 11
Leadscrew and Feed Rod
The leadscrew (J, Figure 11) and feed rod (K,
Figure 11) are mounted on the front of the
machine bed. They are connected to the
gearbox at the left and are supported by
bearings on both ends. Both are equipped with
shear pins.
Feed Gearbox
The gearbox (L, Figure 11) is made from high
quality cast iron and is mounted to the left side
of the machine bed.
Steady Rest
The steady rest (M, Figure 11) serves as a
support for shafts on the free tailstock end. The
steady rest is mounted on the bedway and
secured from below with a bolt, nut and locking
plate. The sliding fingers require continuous
lubrication at the contact points with the
workpiece to prevent them from premature
wear.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the steady rest:
1. Loosen three hex socket cap screws.
2. Loosen knurled screw and open sliding
fingers until the steady rest can be moved
with its fingers around the workpiece.
Secure the steady rest in position.
3. Set the fingers snugly to the workpiece and
secure by tightening three hex socket cap
screws. Fingers should be snug but not
overly tight. Lubricate sliding points with
lead-based grease.
Follow Rest
The traveling follow rest (N, Figure 11) is
mounted on the saddle and follows the
movement of the turning tool. Only two fingers
are required as the place of the third is taken by
the turning tool. The follow rest is used for
turning operations on long, slender workpieces.
It prevents the workpiece from flexing under the
pressure of the cutting tool.
Figure 11 (repeated)
The sliding fingers are set similar to the steady
rest, free of play, but not binding. Always
lubricate adequately with lead-based grease
before operating.
Controls
1. Control Panel: located on front of
headstock.
• Coolant On-Off Switch (A, Figure 12)
turns coolant pump on and off.
• Power Indicator Light (D, Figure 12) is lit
whenever lathe is receiving power.
• Emergency Stop Switch (C, Figure 12)
stops all machine functions (Caution:
Lathe will still have power). Twist
clockwise to re-set.
• Jog Switch (B, Figure 12). Quickly press
and release to rotate the spindle.
2. Headstock Gear Change Levers (F, Figure
12): Located on front of headstock. Move
levers left or right to desired spindle speed.
3. Leadscrew/Feed Rod Directional Lever
(E, Figure 12): Located on front of
headstock at lower left. Changing knob
changes direction of feed.
Figure 12
Do not move knob while
machine is running.
4. Feed/Lead Selector Lever (H, Figure 12):
Located on front of headstock. Used when
setting up for threading or feeding.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Compound Slide (L, Figure 13) is located
on top of the cross slide and can be rotated
360°. There are calibrations in degrees (M,
Figure 13) below the rest to assist in
placement of the compound slide to the
desired angle.
6. Compound Lock (not shown): Lever
located on back of compound slide. Turn
clockwise to lock and counterclockwise to
unlock.
7. Cross Slide Lock (A, Figure 13): Lever
located on left side of cross slide. Turn
clockwise to lock and counterclockwise to
unlock.
8. Carriage Lock (B, Figure 13): Located on
top right of carriage. Turn clockwise to lock,
counterclockwise to unlock.
Carriage lock must be
loose before moving carriage or damage
to lathe may occur.
9. Longitudinal Traverse Handwheel (C,
Figure 13): Located on the apron assembly.
Rotate handwheel clockwise to move the
apron assembly toward the tailstock (right).
Rotate the wheel counterclockwise to move
the apron assembly toward the headstock
(left).
Figure 13
10. Longitudinal/Cross Feed Selector Lever
(E, Figure 13): Can be pushed to upper,
middle and lower three positions. Push the
lever up, cross feed is effected. Push the
lever down, longitudinal feed is effected.
When the lever is in the middle position,
screws can be cut by engaging the half nut.
11. Half Nut Lever (D, Figure 13): Located on
the front of the apron assembly. Used for
threading.
12. Feed Engage Lever (G, Figure 13):
Located in the front of the apron assembly.
Pull lever up to engage. Push lever down to
disengage.
13. Adjustable Feed Clutch (F, Figure 13):
When the machine is overloaded, it can slip.
Then cutting rate must be reduced. Note:
This setting has been calibrated at the
factory and should not need adjustment. If
adjustment ever becomes necessary, follow
the diagram on the front of the apron.
14. Cross Traverse Handwheel (H, Figure 13):
Located above the apron assembly.
Clockwise rotation moves the cross slide
toward the rear of machine.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Compound Rest Traverse Handle (J,
Figure 13): Located on the end of the
compound slide. Rotate clockwise or
counterclockwise to position.
16. Tool Post Clamping Lever (K, Figure 13):
Located on top of the tool post. Rotate
counterclockwise to loosen and clockwise to
tighten.
17. Tailstock Quill Clamping Lever (A, Figure
14): Located on the tailstock. Rotate
clockwise to lock the sleeve. Rotate
counterclockwise to unlock.
18. Tailstock Clamping Lever (B, Figure 14):
Lift up to lock. Push down to unlock. If the
tailstock has a heavy load, tighten the
hexagon head at right side of the tailstock
for auxiliary locking.
19. Tailstock Quill Traverse Handwheel (C,
Figure 14): Rotate clockwise to advance the
quill and counterclockwise to retract it.
Figure 13 (repeated)
20. Tailstock Off-Set Adjustment (D, Figure
14): Two hex socket cap screws located on
the tailstock base are used to off-set the
tailstock for cutting tapers. Loosening one
screw while tightening the other will off-set
the tailstock. Do not clamp the tailstock lock
handle when adjusting.
21. Foot Brake (A, Figure 15): The connecting
rod mechanism is in the bed stand. The
braking device is in the pulley of the
headstock. Press the pedal to stop all lathe
functions. (Caution: Lathe still has power.)
22. Micro Carriage Stop (B, Figure 15): can be
used during manual feed operation. The dial
can be turned for fine tuning the position of
the stop. The micro carriage stop can be
moved along the bed by loosening the two
socket head cap screws underneath the
stop.
Figure 14
23. Bed Cover (C, Figure 15): can be easily
removed to clean out the stand.
Figure 15
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Feed and Thread Selection
1. Reference the feed and thread chart on the
front of the headstock (A, Figure 16).
2. Move levers and knobs (B/C/D/E, Figure 16)
to the appropriate position according to the
feed and thread chart.
Thread Cutting
1. Set forward/reverse lever (F, Figure 16) to
desired direction.
2. Set selector levers (G/H, Figure 16) to
desired R.P.M.
3. Select desired thread using levers (B/C/D/E,
Figure 16).
4. Set selector lever (A, Figure 17) to correct
position (neutral).
Figure 16
5. Engage the half nut lever (B, Figure 17).
6. Make a test cut with scrap material and
check results before cutting regular material.
Gib Adjustments
After a period of time, some of the moving
components may need to be adjusted due to
wear.
Saddle
Turn gib screws on either side of the saddle at
the rear to adjust the drag on the saddle.
Cross Slide
Turn gib screws in the front and rear of the gib
to adjust the drag of the cross slide.
Compound Slide
Turn gib screws to adjust the drag of the
compound slide.
Figure 17
Tailstock Off-Set
Follow the procedure below to off-set the
tailstock to cut shallow tapers:
1. Loosen tailstock in position by lowering
locking handle (B, Figure 18) and loosening
hexagon head eccentric shaft at back of
tailstock.
2. Alternately loosen and tighten front and rear
screws (D, Figure 18). Note: Front screw is
shown.
Figure 18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing Gap Section
1. To remove the gap section, remove four hex
socket cap screws, and two hex cap bolts.
2. Tighten the hex nuts on the tapered
alignment pins to loosen the pins. Once
loosened, they can be removed.
3. Gap section can now be removed.
Installing Removable Gap Section
1. Clean the bottom and the ends of the gap
section thoroughly.
2. Set gap section in place and align the ends.
3. Loosen the nuts on the locating pins and
push down through the gap into the lathe
bed.
4. Replace four hex socket cap screws and
tighten alternately until all are snug.
Belt Replacement and Adjustment
1. Disconnect machine from power source.
Figure 19
2. Open end gear cover, remove lower rear
cover and lower side cover. This will expose
the motor and v-belts.
3. Loosen upper hex nut (A, Figure 19). Place
scrap piece of wood under motor to act as
lever. Lift motor up and block temporarily.
4. Remove belts. Install new belts onto pulleys.
5. Lift up on motor and remove temporary
blocking.
6. Tension belts by loosening lower nut (B,
Figure 19) and tightening upper nut (A,
Figure 19) until light finger pressure causes
approximately 3/4” deflection on each belt.
Figure 20
7. Install covers and connect lathe to the
power source.
Aligning Tailstock to Headstock
1. Fit a 12” ground steel bar between centers
of the headstock and tailstock (Figure 20).
2. Fit a dial indicator to the top slide and
traverse the center line of the bar.
3. If adjustment is needed, align the tailstock
using the off-set screws (D, Figure 21) until
the tailstock is aligned.
Figure 21
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|