Jet Tools Cordless Drill JMD 15 User Manual
OWNER'S MANUAL  
JMD-15/18/18PFN Mill/Drill Machine  
(JMD-18 shown with optional CS-18 stand)  
JET  
P.O. BOX 1349  
Auburn, WA 98071-1349  
e-mail [email protected]  
Phone: 253-351-6000  
Fax: 1-800-274-6840  
M-350020 05/02  
WMH Tool Group  
www.wmhtoolgroup.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13. Keep children and visitors away. All  
visitors should be kept a safe distance from  
the work area.  
WARNING  
Read and understand the entire contents of  
this manual before attempting set-up or  
operation of this mill/drill.  
14. Make the workshop child proof. Use  
padlocks, master switches, and remove  
starter keys.  
1. This machine is designed and intended  
for use by properly trained and  
experienced personnel only. If you are  
not familiar with the proper safe use of  
mill/drills, do not use this machine until  
proper training and knowledge has been  
obtained.  
15. Wear proper apparel.  
Loose clothing,  
gloves, neckties, rings, bracelets, or other  
jewelry may get caught in moving parts.  
Non-slip footwear is recommended. Wear  
protective hair covering to contain long hair.  
Do not wear any type of glove.  
2. Keep guards in place. Safety guards must  
16. Always use safety glasses. Every day  
glasses only have impact resistant lenses;  
they are not safety glasses.  
be kept in place and in working order.  
3. Remove adjusting keys and wrenches.  
Before turning on machine, check to see  
that any adjusting wrenches are removed  
from the tool.  
17. Do not overreach. Keep proper footing  
and balance at all times.  
18. Do not place hands near the cutterhead  
4. Reduce the risk of unintentional starting.  
Make sure switch is in the OFF position  
before plugging in the tool.  
while the machine is operating.  
19. Do not perform any set-up work while  
machine is operating.  
5. Do not force tools. Always use a tool at  
the rate for which it was designed.  
20. Read and understand all warnings  
posted on the machine.  
6. Use the right tool. Do not force a tool or  
attachment to do a job for which it was not  
designed.  
21. This manual is intended to familiarize  
you with the technical aspects of this  
mill/drill. It is not, nor was it intended to  
be, a training manual.  
7. Maintain tools with care. Keep tools  
sharp and clean for best and safest  
performance.  
Follow instructions for  
lubrication and changing accessories.  
22. Failure to comply with all of these  
warnings may result in serious injury.  
8. Always disconnect the tool from the  
power source before adjusting or  
servicing.  
23. Some dust created by power sanding,  
sawing, grinding, drilling and other  
construction activities contains chemicals  
known to cause cancer, birth defects or  
other reproductive harm. Some examples  
of these chemicals are:  
9. Check for damaged parts. Check for  
alignment of moving parts, breakage of  
parts, mounting, and any other condition  
that may affect the tools operation. A guard  
or any part that is damaged should be  
repaired or replaced.  
•
•
Lead from lead based paint  
crystalline silica from bricks and cement and  
other masonry products, and  
•
arsenic and chromium from chemically-  
treated lumber.  
10. Turn power off.  
Never leave a tool  
unattended. Do not leave a tool until it  
comes to a complete stop.  
11. Keep work area clean. Cluttered areas  
and benches invite accidents.  
24. Your risk from those exposures varies,  
depending on how often you do this type of  
work. To reduce your exposure to these  
chemicals: work in a well ventilated area,  
and work with approved safety equipment,  
such as those dust masks that are  
specifically designed to filter out  
12. Do not use in a dangerous environment.  
Do not use power tools in damp or wet  
locations, or expose them to rain. Keep  
work area well lighted.  
microscopic particles  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications:  
JMD-15/18/18PFN  
Stock Number:  
JMD-15 ................................................................................................................................... 350017  
JMD-18 ................................................................................................................................... 350018  
JMD-18PFN ............................................................................................................................ 350020  
Drilling Capacity:  
JMD-15 ............................................................................................................................................1”  
JMD-18/18PFN...........................................................................................................................1-1/4”  
Face Mill Capacity:  
JMD-15 ......................................................................................................................................2-1/2”  
JMD-18/18PFN.................................................................................................................................3”  
End Mill Capacity:  
JMD-15 .........................................................................................................................................1/2”  
JMD-18/18PFN..............................................................................................................................3/4”  
Swing:  
All Models ................................................................................................................................15-7/8”  
Maximum Distance Spindle to Table:  
JMD-15 ..........................................................................................................................................15”  
JMD-18 ..........................................................................................................................................18”  
JMD-18PFN ...................................................................................................................................26”  
Spindle Taper:  
All Models ..................................................................................................................................... R-8  
Spindle Travel:  
JMD-15 ......................................................................................................................................3-1/2”  
JMD-18/18PFN.................................................................................................................................5”  
Quill Diameter:  
JMD-15 ......................................................................................................................................2-1/2”  
JMD-18/18PFN.................................................................................................................................3”  
Head Swivel:  
All Models ....................................................................................................................................360°  
Column Diameter:  
JMD-15 ......................................................................................................................................3-5/8”  
JMD-18/18PFN...........................................................................................................................4-1/2”  
Number of Power Downfeeds (JMD-18PFN only) ....................................................................................3  
Range Of Power Downfeeds (JMD-18PFN only)..................................................... .0.004”, 0.007”, 0.001”  
Number of Spindle Speeds:  
All Models .......................................................................................................................................12  
Range of Spindle Speeds:  
JMD-15 ....................................................................................................................110 – 2,580 RPM  
JMD-18/18PFN.........................................................................................................150 – 3,000 RPM  
Maximum Table Travel:  
JMD-15 ..........................................................................................................................................14”  
JMD-18/18PFN.........................................................................................................................20-1/2”  
Cross Travel:  
JMD-15 ............................................................................................................................................6”  
JMD-18/18PFN.................................................................................................................................7”  
Working Surface of Table:  
JMD-15 .............................................................................................................................7-1/2” x 23”  
JMD-18/18PFN............................................................................................................9-1/2” x 31-3/4”  
Number of T-Slots:  
All Models .........................................................................................................................................4  
T-Slot Size:  
JMD-15 .......................................................................................................................................9/16”  
JMD-18/18PFN..............................................................................................................................5/8”  
T-Slot Centers:  
All Models ..............................................................................................................................1-13/16”  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Overall Dimensions:  
JMD-15 .............................................................................................. 36-1/2”L x 37-1/2”W x 35-1/2”H  
JMD-18 .............................................................................................. 42-1/2”L x 39-3/4”W x 43-1/2”H  
JMD-18PFN ....................................................................................... 42-1/2”L x 39-3/4”W x 51-1/2”H  
Base Dimensions:  
JMD-15 .....................................................................................................................12-1/2” x 19-3/4”  
JMD-18/18PFN..........................................................................................................15-3/4” x 23-3/4”  
Motor (UL Listed):  
JMD-15 ...................................................................................1 HP, 1Ph, 115V/230V Prewired 115V  
JMD-18/18PFN..................................................................................................2 HP, 1Ph, 230V only  
Net Weight (approx.):  
JMD-15 ..................................................................................................................................440 Lbs.  
JMD-18 ..................................................................................................................................660 Lbs.  
JMD-18PFN ...........................................................................................................................700 Lbs.  
Shipping Weight (approx.):  
JMD-15 ..................................................................................................................................540 Lbs.  
JMD-18 ..................................................................................................................................760 Lbs.  
JMD-18PFN ...........................................................................................................................800 Lbs.  
The specifications in this manual are given as general information and are not binding. WMH Tool  
Group reserves the right to effect, at any time and without prior notice, changes or alterations to parts,  
fittings, and accessory equipment deemed necessary for any reason whatsoever.  
Table of Contents  
Warranty .................................................................................................................................................2  
Warning...................................................................................................................................................3  
Specifications.......................................................................................................................................4-5  
Table of Contents ....................................................................................................................................5  
Contents of the Shipping Container .........................................................................................................6  
Unpacking and Clean-up..........................................................................................................................6  
Tools Needed for Assembly.....................................................................................................................6  
Assembly.................................................................................................................................................7  
Installation...............................................................................................................................................7  
Lubrication...............................................................................................................................................8  
Electrical Connections .............................................................................................................................8  
Controls..............................................................................................................................................9-10  
Changing Spindle Speeds.................................................................................................................10-11  
Arbor Replacement................................................................................................................................11  
Gib Adjustment......................................................................................................................................12  
Power Feed Operation...........................................................................................................................12  
Adjusting the Spindle Return Spring ......................................................................................................12  
JMD-15 Parts Lists and Breakdowns.................................................................................................13-18  
JMD-18 Parts Lists and Breakdowns.................................................................................................19-28  
JMD-15 Wiring Diagram ........................................................................................................................29  
JMD-18 Wiring Diagram ........................................................................................................................30  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents of the Shipping Container  
1. Mill/Drill Machine  
Accessory Package:  
1. 1/2” Drill Chuck w/ Chuck Key  
1. Adjustable Carbide Facemill  
1. Facemill Arbor  
2. Bolts, Nuts, and Washers to  
Attach Vise to Table  
1. 2-1/2” Angle Vise (JMD-15)  
1. 3-1/2” Angle Vise (JMD-18/18PFN)  
3. Handle Rods  
3. Rubber Knobs  
1. 3/8”x1” Hex Socket Cap Screw  
1. 3/8” Washer  
1. Crank Body  
1. Crank Handle  
1. 3mm Hex Wrench  
1. 5mm Hex Wrench  
1. 23mm Hex Socket Wrench (JMD-  
18/18PFN)  
3. Hand Wheels w/ Handles  
1. Can Touch-Up Paint  
1. Owner’s Manual  
1. Warranty Card  
1. Lifting Hook  
Unpacking and Clean-up  
1. Finish removing the crate from the mill/drill.  
Unbolt the machine from the crate bottom.  
Report shipping damage, if any, to your  
distributor.  
(JMD-18 shown with optional CS-18 stand)  
2. Clean all rust protected surfaces using a  
mild commercial solvent, kerosene or diesel  
fuel. Do not use paint thinner, gasoline, or  
lacquer thinner. These will damage painted  
surfaces. Cover all cleaned surfaces with a  
light film of Mobil DTE Oil Heavy Medium.  
Tools Needed for Assembly  
8” Adjustable Wrench or 1/4” to 1-1/4”  
Combination Wrench Set  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
bolts. Check for level again. Adjust as  
necessary until the mill/drill is level after the  
fastening hardware has been tightened.  
1. Screw rubber handles (A, Fig. 1) onto  
handle shaft (B, Fig. 1). Screw handle shaft  
into downfeed hub (C, Fig. 1) and tighten.  
Flat spot on shaft accommodates  
a
combination or adjustable wrench. Note:  
Handle shafts are already installed into hub  
on JMD-18PFN.  
2. Repeat for other two shaft assemblies.  
3. Slide crank (D, Fig. 2) onto shaft and tighten  
set screw (E, Fig. 2). Be sure set screw  
seats on flat part of shaft.  
4. Thread handle (F, Fig. 2) into crank and  
tighten.  
5. Slide handwheel (G, Fig. 3) onto table  
handwheel shaft and tighten set screw.  
Insert handle (H, Fig. 3) into handwheel and  
tighten.  
6. Repeat for two remaining table hand  
wheels.  
Installation  
WARNING  
Machine is heavy! Use an appropriate  
lifting device and use extreme caution when  
moving the machine to its final location.  
Failure to comply may cause serious injury!  
1. The location for the mill/drill should be well  
lit, dry, and have room enough to allow the  
head to rotate 360°.  
2. Open the belt cover and thread the lifting  
hook into the head. There is a threaded  
hole found between the column and the  
spindle pulley.  
3. Carefully lift the mill/drill with properly rated  
equipment to a sturdy stand or work bench.  
For best performance, through bolt the  
mill/drill to a bench or stand.  
4. Remove the lifting hook.  
5. Before bolting the mill/drill to a bench or  
stand, the unit must be level in both  
directions. Place a level on the table in both  
directions.  
6. If the table is not level, shim under the low  
corner(s) until level. Tighten the fastening  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Lubrication  
4. Change the plug to one that is rated 230V or  
hard wire the power cord.  
Lubricate ball oilers (A, Fig. 4) found by the X/Y-  
axis hand wheels, the oiler found by the  
raising/lowering crank handle, and the oiler on  
the front of the bed once daily with Mobil DTE  
Oil Heavy Medium.  
The JMD-18/18PFN is rated at 230V only.  
Again, be sure the power source is compatible  
with the mill/drill before connecting to the power  
source. Make sure the mill/drill is properly  
grounded.  
Lubricate the ways (B, Fig. 4) once daily with  
Mobil DTE Oil Heavy Medium.  
If the head does not raise, or lower smoothly  
apply Mobilith AW2 to the rack, and Mobil  
DTE Oil Heavy Medium to the column.  
If the feed handles do not turn smoothly apply  
Mobilith AW2 to the cross, and longitudinal lead  
screws (C, Fig. 4). Access the cross lead screw  
by moving the table forward and removing the  
way cover.  
The spindle bearings are permanently sealed  
and require no lubrication.  
Electrical Connections  
WARNING  
A qualified electrician must make all  
electrical connections!  
Failure to comply may cause serious injury!  
Before making any electrical connections, make  
sure the power source available is compatible  
with the machine. Also, press the “Off” button  
on the front of the machine before connecting to  
the power source.  
The JMD-15 is rated at 115/230V and comes  
from the factory prewired at 115V.  
This  
mill/drill comes with a plug designed for use on  
a circuit with an outlet that looks like (A, Fig. 5).  
The JMD-15 has  
a
grounding prong as  
illustrated in (A, Fig. 5).  
To switch the JMD-15 to 230V operation:  
1. Disconnect the machine from the power  
source.  
2. Remove the junction box cover on the  
motor.  
3. Change the wires according to the diagram  
on the inside of the junction box cover, and  
replace the junction box cover.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls  
Longitudinal Hand Wheels: (X-axis) (A, Fig. 6)  
Located on either side of the table. Moves table  
side to side.  
Cross Feed Hand Wheel: (Y-axis) (B, Fig. 6)  
Located on the front of the base. Moves table  
toward, or away from the column.  
Adjustable Table Stops: (C, Fig. 6)  
Located on table front. Adjust to stop table at  
any setting along the longitudinal axis.  
Table Locks: (D & E, Fig. 6)  
Longitudinal table locks are located on front of  
the table. Cross-feed table locks are located on  
the right side under the table. Turn clockwise to  
lock.  
Depth Stop:  
JMD-15: (K, Fig. 8) located on the left side. Set  
nuts for desired depth stop.  
JMD-18: (F, Fig. 7) located in the front. Push in  
the button on the front of the quick adjust stop  
and move to desired position.  
JMD-18PFN: Set the depth stop on the power  
down feed assembly to desired depth for  
repetitive drilling to the same depth, see “Power  
Feed Operation” on page 12.  
Downfeed Handles: (G, Fig. 7)  
Located on the right side of the head casting.  
Counter-clockwise movement advances the quill  
toward the table. Return spring retracts the  
handles. Note: the knob (I, Fig. 7) must be  
loose for the downfeed handles to work.  
Fine Feed Hand Wheel: (H, Fig. 7)  
Located on the front of the head casting. To  
activate, tighten the knob (I Fig. 7) and turn the  
power feed speed range dial (J, Fig. 7) to zero.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Motor Mount Lock Lever: (A, Fig. 9)  
Located on the right side of the head casting.  
Locks and unlocks the motor mounting plate  
enabling the user to tension v-belts.  
Head Pivot Lock: (B, Fig. 9)  
Located on the right rear of the head casting.  
Loosen two hex nuts to rotate the head 360°.  
Tighten two hex nuts to lock the head in  
position.  
On-Off Switch: (C, Fig. 10)  
Located on the front of the head casting. Turns  
power on and off to the mill/drill.  
Quill Lock Handle: (D, Fig. 10)  
Located on the front left of the head casting.  
Turn clockwise to lock the quill in the desired  
position. Turn counter-clockwise to release.  
Head Elevating Crank Handle: (E, Fig. 10)  
Located at left rear of head casting. Loosen  
head pivot lock nuts (B, Fig. 9) and turn handle  
clockwise to raise head on the column and  
counter-clockwise to lower head.  
WARNING  
This machine is designed and intended for  
use by properly trained and experienced  
personnel only! If you are not familiar with  
the proper and safe use of mill/drills, do not  
use this machine until proper training and  
knowledge have been obtained!  
Failure to comply may cause serious injury!  
Changing Spindle Speeds  
1. Disconnect the machine from the power  
source, unplug.  
2. Loosen the motor mount lock lever (F, Fig,  
11) and pull the motor toward the head  
casting to release tension on the v-belts.  
3. Release two latches (G, Fig. 11) on belt  
cover and slide pulley guard open (I, Fig.  
11).  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Arrange the v-belts (A, Fig. 12) on the  
pulleys (B, Fig. 12) for the desired speed  
according to the speed chart (H, Fig. 11) on  
the belt cover.  
Note: For best results, all milling operations  
should be done with the quill/spindle as close to  
the head assembly as possible. Lock spindle  
and table in place before starting milling  
operations.  
5. Tension the v-belts by pushing the motor  
away from the head casting and locking the  
motor mount lock lever (F, Fig. 11). Note:  
Proper tension is achieved when the slack  
in the belt is taken up and the belt does not  
slip during operation of the mill/drill.  
Arbor Replacement  
1. Disconnect machine from the power  
source, unplug.  
2. Release two latches (G, Fig. 11) on the belt  
cover and slide the pulley guard open (I,  
Fig. 11).  
3. Hold the spindle pulley (B, Fig. 12) to keep  
the pulley from moving while loosening the  
drawbar (C, Fig. 12) with a wrench.  
4. Loosen the drawbar approximately three to  
four full turns.  
5. Tap the drawbar head with a rubber mallet  
to dislodge the arbor.  
CAUTION  
Do not loosen the drawbar more than three  
or four turns before hitting with a rubber  
mallet. Damage to the drawbar threads may  
occur.  
6. Grasp the arbor with one hand while  
loosening the draw bar with the other.  
Continue to loosen the drawbar until the  
arbor can be withdrawn from the spindle.  
Wipe out the spindle with a clean dry rag.  
7. Wipe down the new arbor with a clean dry  
rag and place the arbor into the spindle.  
Thread the drawbar into the arbor. Tighten  
the drawbar with a wrench while holding on  
to the spindle pulley.  
WARNING  
Use caution when tightening drawbar! Do  
not allow hand to get pinched between  
pulley and belt!  
Failure to comply may cause serious injury!  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Loosen knob (I, Fig. 15) just enough to  
rotate spring cap past the notch (J, Fig. 15).  
Gib Adjustment  
After a period of time, movement of the table  
over the ways will cause normal wear. To  
adjust the gibs for this wear:  
3. Rotate the spring cap clockwise to decrease  
spring tension.  
Rotate the spring cap  
counter-clockwise to increase spring  
tension.  
1. The horizontal gib adjustment screw (A, Fig.  
13) is found to the right on the table face.  
The traverse gib adjustment screw (B, Fig.  
13) is found on the right side of the saddle  
under the table.  
2. Turn each screw slightly clockwise to  
tighten. Turn the table hand wheels and  
check the tension.  
3. Re-adjust as required.  
Power Feed Operation (JMD-18PFN only)  
Caution  
Make all power feed settings with power to  
the machine turned off!  
Failure to comply may cause damage to the  
machine!  
1. Set the power feed speed range dial (C, Fig.  
14) to the desired rate.  
2. Set the depth stop to the desired setting by  
lowering the quill to the desired depth and  
holding in place. Turn the collar (D, Fig. 14)  
counter-clockwise until zero is indicated and  
then tighten the lock handle (E, Fig. 14)  
3. Start the mill/drill and pull one of two  
handles (F, Fig. 14) away from the column  
to start the power downfeed.  
4. Once the downfeed has reached the depth  
stop, the trip will release and the spindle will  
retract.  
5. To stop the feed before the cycle has ended  
or to disengage the fine feed (G, Fig. 14),  
press one of two handles toward the  
column.  
Adjusting the Spindle Return Spring  
The spindle return comes pre-set from the  
factory and should not need any adjustment.  
1. You do not want to remove the spring cap  
(H, Fig. 15).  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
JMD-15 Head Assembly  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts List for the JMD-15 Mill/Drill  
Head Assembly  
Index Part  
No. No.  
Description  
Size  
Qty.  
1..........JMD15-001 .................. Drawbar............................................................. ...................................1  
2..........JMD15-002A ................ Spindle Lock Nut ............................................... ...................................1  
3..........JMD15-003 .................. Spindle Pulley.................................................... ...................................1  
5..........JMD15-005 .................. Outer Bearing Plate........................................... ...................................1  
6..........JMD15-006A ................ Spindle Taper Sleeve ........................................ ...................................1  
7..........BB-6007ZZ .................. Ball Bearing....................................................... 6007ZZ.......................2  
8..........JMD15-008 .................. Bearing Spacer.................................................. ...................................1  
9..........JMD15-009 .................. C-Ring............................................................... ...................................1  
10........JMD18-010 .................. C-Ring............................................................... ...................................1  
11........JMD15-011 .................. Head.................................................................. ...................................1  
12........JMD15-012 .................. Rubber Flange................................................... ...................................1  
13........JMD15-013 .................. Feed Base......................................................... ...................................1  
14........JMD15-014 .................. Lock Nut............................................................ ...................................2  
15........BB-30205..................... Taper Roller Bearing.......................................... 30205 .........................1  
16........JMD15-016 .................. Rack Sleeve...................................................... ...................................1  
17........JMD15-017 .................. Spindle Shaft..................................................... ...................................1  
18........BB-30206..................... Taper Roller Bearing.......................................... 30206 .........................1  
19........JMD15-019 .................. Bearing Cap ...................................................... ...................................1  
20........JMD15-020 .................. Cutting Arbor ..................................................... ...................................1  
21........JMD15-021 .................. Chuck Arbor ...................................................... R8 x JT6.....................1  
22........JMD18-022 .................. Handle............................................................... ...................................1  
23........JMD15-023 .................. Retainer Ring .................................................... ...................................1  
24........JMD15-024 .................. Lock Handle ...................................................... ...................................1  
25........JMD15-025 .................. Fixed Collar....................................................... ...................................1  
26........JMD15-026 .................. Fixed Collar Thread........................................... ...................................1  
27........JMD15-027 .................. Screw Key ......................................................... 3/8..............................1  
35........JMD18-035 .................. Bearing Spacer.................................................. ...................................1  
38........JMD18-038 .................. Lock Bolt w/ Knob.............................................. ...................................1  
39........JMD18-039 .................. Handle Rod ....................................................... ...................................3  
40........JMD18-040 .................. Knob.................................................................. ...................................3  
42........JMD18-042 .................. Feed Handle Wheel........................................... ...................................1  
44........JMD18-044 .................. Micro Adjusting Indicator ................................... ...................................1  
45........JMD18-045 .................. Worm Cover...................................................... ...................................1  
46........BB-6202Z..................... Ball Bearing....................................................... 6202Z.........................2  
47........JMD18-047 .................. Worm Shaft....................................................... ...................................1  
51........JMD18-051 .................. Leaf Screw ........................................................ ...................................1  
52........JMD15-052 .................. Head Lock Bolt .................................................. 1/2"x7”........................2  
54........JMD15-054 .................. Graduated Rod and Dial Assembly .................... ...................................1  
55........JMD15-054 .................. Depth Scale....................................................... ...................................1  
56........JMD15-056A ................ Switch................................................................ ...................................1  
57........JMD15-057 .................. Name Plate ....................................................... ...................................1  
58........JMD15-058 .................. Head Handle...................................................... ...................................1  
59........JMD15-059 .................. Worm Shaft....................................................... ...................................1  
60........JMD15-060 .................. Worm Gear ....................................................... ...................................1  
61........JMD15-061 .................. Shaft.................................................................. ...................................1  
62........JMD18-062 .................. Compression Spring .......................................... ...................................1  
63........JMD15-063 .................. Pin..................................................................... ...................................1  
66........JMD15-066 .................. Motor Mount ...................................................... ...................................1  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index Part  
No. No.  
Description  
Size  
Qty.  
67........JMD15-067 .................. Motor................................................................. 1HP, 1Ph....................1  
............JMD15-067A ................ Capacitor (not shown)........................................ 125uF, 250VAC..........1  
69........JMD15-069P ................ Belt Cover ......................................................... ...................................1  
69-1.....JMD15-069P1 .............. Upper Belt Cover Cap........................................ ...................................1  
69-2.....JMD15-069P2 .............. Upper Belt Cover Plate...................................... ...................................1  
70........JMD15-070 .................. Motor Pulley ...................................................... ...................................1  
71........VB-A31 ........................ V-Belt ................................................................ A31.............................1  
72........BB-6204Z..................... Ball Bearing....................................................... 6204Z.........................2  
73........JMD15-073 .................. Inter Pulley ........................................................ ...................................1  
74........VB-A38 ........................ V-Belt ................................................................ A38.............................1  
75........JMD15-075P ................ Inter Pulley Shaft............................................... ...................................1  
76........JMD15-076P ................ Speed Change Inter Pulley Base ....................... ...................................1  
79........JMD18-079 .................. Rubber Collar .................................................... ...................................1  
85........JMD18-085 .................. Screw w/ Plumb Knob........................................ ...................................1  
86........JMD15-086 .................. Cutter ................................................................ ...................................1  
............JMD15-086A ................ Cutter Insert (not shown).................................... ...................................4  
87........JMD15-087 .................. Drill Chuck......................................................... ...................................1  
87A......JMD15-087A ................ Chuck Key......................................................... ...................................1  
90........JMD15-090 .................. Self Tapping Screw ........................................... ...................................2  
103......JMD18-103 .................. Spring Cover ..................................................... ...................................1  
104......JMD18-104 .................. Spring................................................................ ...................................1  
105......JMD18-105 .................. Spring Base....................................................... ...................................1  
106......JMD15-106 .................. Pinion Shaft....................................................... ...................................1  
107......JMD18-107 .................. Worm Gear ....................................................... ...................................1  
108......JMD18-108 .................. Gear Housing .................................................... ...................................1  
110......JMD18-110 .................. Hub ................................................................... ...................................1  
115......JMD18-115 .................. Spring................................................................ ...................................1  
122......JMD18-077 .................. Clip Plate........................................................... ...................................1  
131......TS-0813032 ................. Pan Head Screw................................................ 1/4"x1/2”.....................5  
132......TS-0680021 ................. Washer.............................................................. 1/4".............................5  
133......JMD18-133 .................. Round Head Screw............................................ 1/4"x3/8”.....................3  
134......TS-0050091 ................. Hex Head Bolt ................................................... 1/4"x2”........................1  
135......TS-0561011 ................. Hex Nut ............................................................. 1/4".............................1  
136......TS-0561051 ................. Hex Nut ............................................................. 1/2".............................2  
137......JMD15-137 .................. Lock Washer ..................................................... ...................................1  
138......JMD15-138 .................. Rivet.................................................................. ...................................2  
139......JMD18-139 .................. Round Head Screw............................................ 3/16”x3/4”...................3  
140......JMD18-140 .................. Spring Pin.......................................................... 3x12"..........................2  
141......TS-0561031 ................. Hex Nut ............................................................. 3/8..............................3  
142......JMD18-142 .................. Key.................................................................... 7x7x20 .......................1  
143......TS-0208041 ................. Hex Socket Cap Screw...................................... 5/16”x3/4”...................2  
144......TS-0680021 ................. Washer.............................................................. 1/4".............................1  
145......TS-0270021 ................. Set Screw.......................................................... 5/16”x5/16” .................3  
146......TS-0267031 ................. Set Screw.......................................................... 1/4"x5/16”...................1  
147......JMD18-147 .................. Round Head Screw............................................ 3/16”x1/2”...................2  
148......JMD18-148 .................. C-Retainer Ring................................................. ...................................1  
150......TS-0561051 ................. Hex Nut ............................................................. 1/2".............................2  
151......TS-0680061 ................. Washer.............................................................. 1/2".............................2  
152......JMD15-152 .................. Round Head Screw............................................ 1/4"x3/8”.....................6  
153......TS-0271061 ................. Set Screw.......................................................... 3/8”x5/8”.....................1  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index Part  
No. No.  
Description  
Size  
Qty.  
154......TS-0561071 ................. Hex Nut ............................................................. 5/8”.............................2  
155......TS-0680031 ................. Washer.............................................................. 5/16”...........................8  
156......TS-0051051 ................. Hex Head Bolt ................................................... 5/16”x1”......................4  
157......TS-0060051 ................. Hex Head Bolt ................................................... 3/8”x1/2”.....................2  
158......TS-0561021 ................. Hex Nut ............................................................. 5/16”...........................4  
159......JMD18-159 .................. Key.................................................................... 7x7x40 .......................1  
160......TS-0051071 ................. Hex Head Bolt ................................................... 5/16”x1-1/2”................2  
161......TS-0680031 ................. Washer.............................................................. 5/16”...........................2  
187......TS-0680021 ................. Washer.............................................................. 1/4".............................2  
188......JMD18-188 .................. Pan Head Screw................................................ 3/16”x3/8”...................1  
208......TS-0561031 ................. Hex Nut ............................................................. 3/8”.............................1  
............JMD15-SC ................... Speed Chart Label (not shown).......................... ...................................1  
............JMD15-JL .................... Jet Label (not shown)......................................... ...................................1  
............JMD15-ID..................... I.D. Label (not shown)........................................ .....................................  
............JMD15-AP ................... Accessory Package (not shown) *...................... ...................................1  
............JMD18-302 .................. Magnetic Contactor - (not shown) ...................... ...................................1  
............JMD15-303 .................. Thermal Relay (not shown)................................ RH10E/15...................1  
* Contents of the Accessory Package (JMD15-AP):  
............JMD15-020 .................. Cutter Arbor....................................................... ...................................1  
............JMD15-039 .................. Handle............................................................... ...................................3  
............JMD15-040 .................. Knob.................................................................. ...................................3  
............JMD15-087 .................. Drill Chuck......................................................... ...................................1  
............JMD15-086 .................. Cutter ................................................................ ...................................1  
............365534......................... Angle Vise ......................................................... ...................................1  
............JMD15-022 .................. Handle............................................................... ...................................4  
............JMD15-201 .................. Wheel................................................................ ...................................3  
............JMD15-058 .................. Handle Crank..................................................... ...................................1  
............MP-007 ........................ Paint.................................................................. ...................................1  
............TS-152704 ................... Hex Wrench ...................................................... 3mm...........................1  
............TS-152705 ................... Hex Wrench ...................................................... 4mm...........................1  
............TS-152706 ................... Hex Wrench ...................................................... 5mm...........................1  
............JMD15-381 .................. Washer.............................................................. ...................................1  
............JMD15-380 .................. Hex Bolt ............................................................ ...................................1  
............JMD15-377 .................. Hex Bolt ............................................................ ...................................2  
............JMD15-378 .................. Hex Nut ............................................................. ...................................2  
............JMD15-379 .................. Washer.............................................................. ...................................2  
............MP-007 ........................ Touch Up Paint.................................................. ...................................1  
............TS-0071011 ................. Hex Cap Bolt ..................................................... 5/8”x1-1/2”..................3  
............TS-0680081 ................. Flat Washer....................................................... 5/8”.............................3  
............TS-0561071 ................. Hex Nut ............................................................. 5/8”.............................3  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
JMD-15 Table, Base, and Column Assembly  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts List for JMD-15  
Table, Base, and Column Assembly  
Index Part  
No. No.  
Description  
Size  
Qty.  
1..........JMD18-201 .................. Table Hand Wheel............................................. ...................................3  
1-1.......JMD18-201-1 ............... Bolt.................................................................... ...................................3  
1-2.......JMD18-201-2 ............... Handle............................................................... ...................................3  
1-3.......JMD18-201-3 ............... Nut .................................................................... ...................................3  
2..........JMD18-202 .................. Dial Clutch......................................................... ...................................2  
2-1.......JMD18-202-1 ............... Graduated Dial .................................................. ...................................2  
3..........BB-51103..................... Thrust Bearing................................................... 51103 .........................4  
4..........JMD15-204 .................. Square Flange................................................... ...................................1  
4-2.......JMD18-204-2 ............... Rivet.................................................................. ...................................4  
5..........JMD15-205 .................. Table Screw ...................................................... ...................................1  
6..........JMD15-206 .................. Base.................................................................. ...................................1  
7..........JMD15-207 .................. Gib Strip............................................................ ...................................1  
8..........JMD15-208 .................. Column Base..................................................... ...................................1  
9..........JMD15-209 .................. Column Flange Ring.......................................... ...................................1  
10........JMD15-210 .................. Rack.................................................................. ...................................1  
11........JMD15-211 .................. Column Cap ...................................................... ...................................1  
12........JMD15-212 .................. Adjustment Screw.............................................. ...................................2  
13........JMD18-213 .................. Leaf Screw ........................................................ ...................................2  
13-1.....JMD18-213 .................. Locking Handle.................................................. ...................................2  
14........JMD18-214 .................. Block ................................................................. ...................................1  
15........JMD18-215 .................. Table Base Nut.................................................. ...................................1  
16........JMD15-216 .................. Center Base....................................................... ...................................1  
17........JMD15-217 .................. Way Cover ........................................................ ...................................1  
19........JMD18-219 .................. Bracket Plate..................................................... ...................................1  
20........JMD18-220 .................. Table Clutch ...................................................... ...................................1  
22........JMD15-222 .................. Left Flange ........................................................ ...................................1  
23........JMD18-223 .................. Table Nut........................................................... ...................................1  
24........JMD15-224 .................. Table Screw ...................................................... ...................................1  
26........JMD15-226 .................. Right Flange...................................................... ...................................1  
27........JMD15-227 .................. Gib Strip............................................................ ...................................1  
28........JMD15-228 .................. Table................................................................. ...................................1  
29........JMD18-229 .................. Block ................................................................. ...................................2  
30........JMD18-230 .................. Ring................................................................... ...................................2  
121......JMD15-121 .................. Indicator Plate ................................................... ...................................2  
143......TS-0207021 ................. Hex Socket Cap Screw...................................... 1/4"x1/2”.....................2  
145......TS-0270021 ................. Set Screw.......................................................... 5/16”x5/16” .................1  
166......JMD18-366 .................. Spring Pin.......................................................... ...................................3  
167......JMD18-367 .................. Zero Indicator w/ Screw ..................................... 1/4"x3/8”.....................2  
168......JMD18-368 .................. Oil Ball .............................................................. ...................................5  
169......TS-0209031 ................. Hex Socket Cap Screw...................................... 3/8”x3/4”.....................8  
175......TS-0061071 ................. Hex Head Bolt ................................................... 7/16”x2”......................4  
178......TS-0208111 ................. Hex Cap Bolt ..................................................... 5/16”x2-1/4”................1  
179......TS-0051011 ................. Hex Cap Bolt ..................................................... 5/16”x1/2”...................6  
180......TS-1502041 ................. Hex Socket Cap Screw...................................... M5x16 ........................2  
189......TS-0267041 ................. Set Screw.......................................................... 1/4"x3/8”.....................3  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
JMD-18/18PFN Head Assembly  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts List for the JMD-18 Mill/Drill  
Head Assembly  
Index Part  
No. No.  
Description  
Size  
Qty.  
1..........JMD18N-001................ Head Body......................................................... ...................................1  
2..........JMD18-001 .................. Draw Bar ........................................................... R8 ..............................1  
3..........JMD18-002A ................ Spindle Lock Nut ............................................... ...................................1  
4..........JMD18-003A ................ Spindle Pulley.................................................... ...................................1  
5..........JMD18-005 .................. Outer Bearing Plate........................................... 105x66 .......................1  
6..........JMD18-133 .................. Round Head Screw............................................ 1/4”x3/8”.....................3  
7A........JMD18-006A ................ Spindle Taper Sleeve Assembly ........................ ...................................1  
7-1.......JMD18-006 .................. Spindle Taper Sleeve ........................................ ...................................1  
7-2.......BB-6009ZZ .................. Ball Bearing....................................................... 6009ZZ.......................2  
7-3.......JMD18-008 .................. Spacer............................................................... 74x68 .........................1  
7-4.......JMD18-023 .................. Fixed Ring......................................................... 2x4 .............................1  
8..........JMD18-009 .................. C-Retaining Ring ............................................... 3x80 ...........................1  
9..........JMD18-012 .................. Rubber Flange................................................... ...................................1  
10........JMD18N-010................ Feed Base......................................................... ...................................1  
11A......JMD18-014A ................ Rack Sleeve Set................................................ ...................................1  
11-1.....JMD18-014 .................. Lock Nut............................................................ ...................................2  
11-2.....JMD18-137 .................. Lock Washer ..................................................... 30206 .........................1  
11-3.....BB-30206..................... Taper Roller Bearing.......................................... ...................................1  
11-4.....JMD18-016 .................. Rack Sleeve...................................................... R8 ..............................1  
11-5.....BB-30207..................... Taper Roller Bearing.......................................... 30207 .........................1  
11-6.....JMD18-017 .................. Spindle Shaft..................................................... R8 ..............................1  
11-7.....JMD18-019 .................. Bearing Cap ...................................................... R8 ..............................1  
13........JMD18-021 .................. Chuck Arbor ...................................................... R8 7/16” .....................1  
14........JMD18-020 .................. Cutter Arbor....................................................... 25.4 7/16” ...................1  
15A......JMD18N-015A.............. Graduated Rod Assembly.................................. ...................................1  
15-1.....JMD18N-15-1............... Depth Scale Stud............................................... ...................................1  
15-2.....JMD18N-15-2............... Adjustable Stop ................................................. ...................................1  
15-3.....JMD18N-15-3............... Spring................................................................ ...................................1  
15-4.....JMD18N-15-4............... Push Button....................................................... ...................................1  
15-5.....JMD18N-15-5............... Hex Socket Cap Screw...................................... M5x10 ........................1  
15-6.....JMD18N-15-6............... Washer.............................................................. 3/8”.............................1  
15-7.....JMD18N-15-7............... Hex Nut ............................................................. 3/8”.............................1  
17........TS-0050091 ................. Hex Head Screw................................................ 1/4”x2”........................1  
18........TS-0561011 ................. Hex Nut ............................................................. 1/4”.............................1  
20........JMD18-106 .................. Pinion Shaft....................................................... ...................................1  
21........JMD18-188 .................. Flat Cross Head Screw...................................... 3/16”x3/8”...................1  
22........JMD18-142 .................. Key.................................................................... 7x7x20mm .................1  
23A......JMD18N-023A.............. Gear Housing Assembly .................................... ...................................1  
23-1.....JMD18N-023................ Gear Housing .................................................... ...................................1  
23-2.....JMD18-047 .................. Worm Shaft....................................................... ...................................1  
23-3.....BB-6202Z..................... Ball Bearing....................................................... 6202ZZ.......................2  
23-4.....JMD18-148 .................. C-ring ................................................................ 15...............................1  
23-5.....JMD18-035 .................. Bearing Spacer.................................................. 34x27.5 ......................1  
24........TS-0208021 ................. Hex Socket Cap Screw...................................... 5/16”x1/2”...................2  
25........JMD18-107 .................. Worm Gear ....................................................... ...................................1  
26........JMD18-115 .................. Spring................................................................ ...................................1  
27........JMD18-110 .................. Hub ................................................................... ...................................1  
28........JMD18-038 .................. Knob.................................................................. ...................................1  
29........JMD18-039 .................. Shaft.................................................................. ...................................3  
30........JMD18N-030................ Knob.................................................................. ...................................3  
31........JMD18-045 .................. Flange ............................................................... ...................................1  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index Part  
No. No.  
Description  
Size  
Qty.  
32........JMD18-047 .................. Round Head Screw............................................ 3/16”x3/8”...................2  
33........JMD18N-033................ Micro Adjusting Indicator ................................... ...................................1  
33-1.....TS-0267021 ................. Set Screw.......................................................... 1/4”x1/4”.....................1  
35........JMD18N-035A.............. Feed Handle Wheel Assembly........................... ...................................1  
35-1.....JMD18N-035-1............. Set Screw.......................................................... M8x10 ........................1  
37........JMD18-105 .................. Spring Base....................................................... ...................................1  
37-1.....JMD18-140 .................. Spring Pin.......................................................... ...................................1  
39........JMD18-139 .................. Round Head Screw............................................ 3/16”x3/4”...................3  
40A......JMD18-103A ................ Spring Cover Assembly ..................................... ...................................1  
40-1.....JMD18-103 .................. Spring Cover ..................................................... ...................................1  
40-2.....JMD18-104 .................. Spring................................................................ ...................................1  
41........JMD18-187 .................. Washer ............................................................. 1/4”x1”........................1  
42........TS-0680021 ................. Washer.............................................................. 1/4”.............................1  
43........JMD18-187 .................. Lock Washer ..................................................... 1/4”x1”........................1  
44........JMD18-085 .................. Knob.................................................................. ...................................1  
45........JMD18-059 .................. Worm Shaft....................................................... ...................................1  
46........JMD18-114 .................. Bushing ............................................................. ...................................1  
47A......JMD18-101A ................ Head Raise Bracket Assembly........................... ...................................1  
47-1.....JMD18-101 .................. Head Raise Bracket........................................... ...................................1  
47-2.....JMD18-060 .................. Worm Gear ....................................................... ...................................1  
47-3.....JMD18-061 .................. Shaft.................................................................. 9/16”...........................1  
47-4.....JMD18-154 .................. C-ring ................................................................ S14.............................2  
48........TS-0207061 ................. Hex Socket Cap Screw...................................... 1/4”x1”........................4  
49........JMD18-058 .................. Head Handle ..................................................... ...................................1  
49-1.....TS-0271061 ................. Set Screw.......................................................... 3/8”x5/8”.....................1  
51........JMD18-022 .................. Handle............................................................... ...................................1  
51-1.....TS-0561031 ................. Hex Nut ............................................................. 3/8”.............................1  
52........JMD18-026 .................. Fixed Collar (Thread)......................................... ...................................1  
53........JMD18-025 .................. Fixed Collar....................................................... ...................................1  
54........JMD18N-054................ Washer.............................................................. 1/2”x7/8”.....................1  
55........JMD18-024 .................. Handle Rod ....................................................... ...................................1  
56........JMD18-027 .................. Screw Key ......................................................... 3/8”.............................1  
57........TS-0561031 ................. Hex Nut ............................................................. 3/8”.............................1  
58........JMD18-062 .................. Spring................................................................ ...................................1  
59........JMD18-063 .................. Pin..................................................................... ...................................1  
60........JMD18-079 .................. Rubber Collar .................................................... ...................................1  
61........JMD18-052 .................. Bolt.................................................................... 5/8”x6”........................2  
62........TS-0680081 ................. Washer.............................................................. 5/8”.............................2  
63........TS-0561071 ................. Hex Nut ............................................................. 5/8”.............................2  
64........JMD18-050 .................. Lock Handle ...................................................... ...................................1  
65........JMD18N-065................ Knob.................................................................. ...................................1  
66A......JMD18N-066A.............. Front Cover Plate Assembly .............................. ...................................1  
66-1.....JMD18N-066-1............. Front Cover Plate .............................................. ...................................1  
66-2.....JMD18-056A ................ Push Button Switch............................................ ...................................1  
66-3.....JMD18N-066-3............. Screw ................................................................ M5x20 ........................2  
67........JMD18N-067................ Round Head Screw............................................ M6x12 ........................4  
71........JMD18-069 .................. Poly Belt Cover ................................................. ...................................1  
72........JMD18-069A ................ Pulley Cover...................................................... ...................................1  
74........JMD18-069-1 ............... Spindle Cover.................................................... ...................................1  
75........JMD18-069-3 ............... Screw ................................................................ 3mm...........................2  
76........TS-0680032 ................. Flat Washer....................................................... 5/16”...........................4  
77........TS-0051011 ................. Hex Head Bolt ................................................... 5/16”x1/2”...................4  
79........JMD18-SC ................... Spindle Speed Chart.......................................... ...................................1  
80........JMD18N-080................ Pulley Base ....................................................... ...................................1  
81........TS-0561071 ................. Hex Nut ............................................................. 5/8”.............................1  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index Part  
No. No.  
Description  
Size  
Qty.  
82........TS-0680031 ................. Washer.............................................................. 5/16”...........................2  
83........TS-0051071 ................. Hex Head Bolt ................................................... 5/16”x1-1/2”................2  
84A......JMD18-075A ................ Inter Pulley Assembly ........................................ ...................................1  
84-1.....JMD18-075 .................. Inter Pulley Shaft............................................... ...................................1  
84-2.....JMD18-073 .................. Inter Pulley ........................................................ ...................................1  
84-3.....BB-6204Z..................... Ball Bearing....................................................... 6204ZZ.......................2  
84-4.....JMD18-010 .................. C-ring ................................................................ 2x52 ...........................1  
85........TS-0561071 ................. Hex Nut ............................................................. 5/8”.............................1  
86........JMD18-070 .................. Motor Pulley ...................................................... ...................................1  
86-1.....TS-0270021 ................. Set Screw.......................................................... 5/16”x5/16” .................2  
88........VB-B33 ........................ V-Belt ................................................................ B33.............................1  
89........VB-B42 ........................ V-Belt ................................................................ B42.............................1  
90........JMD18-077 .................. Wire Relief Retainer .......................................... ...................................1  
91........TS-0051011 ................. Hex Head Screw................................................ 5/16”x1/2”...................1  
92........JMD18-066 .................. Motor Mount Plate ............................................. ...................................1  
93........JMD18-067 .................. Motor................................................................. 2HP, 1Ph 230V Only...1  
94........TS-0680031 ................. Flat Washer....................................................... 5/16”...........................8  
95........TS-0051051 ................. Hex Head Bolt ................................................... 5/16”x1”......................4  
96........TS-0561021 ................. Hex Nut ............................................................. 5/16”...........................4  
97........TS-0061011 ................. Hex Head Bolt ................................................... 7/16”x3/4”...................2  
98........JMD18-159 .................. Key.................................................................... 7x7x37mm .................1  
113......JMD18-087 .................. Drill Chuck......................................................... 1/2” JT6......................1  
114......JMD18-086 .................. Milling Cutter ..................................................... 25.4mm ......................1  
115......JMD18N-115................ Power Cable...................................................... 230V...........................1  
116......JMD18N-116................ Lamp Assembly................................................. 115V...........................1  
117......JMD18N-117................ Motor Cable....................................................... ...................................1  
............JMD15-JL .................... Jet Label (not shown)......................................... ...................................1  
............JMD18-ID..................... I.D. Label (not shown)........................................ .....................................  
............JMD18-AP ................... Accessory Package (not shown) *...................... ...................................1  
............JMD18-302 .................. Magnetic Contactor (not shown)......................... ...................................1  
............JMD18-303 .................. Thermal Relay (not shown)................................ RH10E/15...................1  
............JMD18-320-01 ............. Special Arbor Washer (not shown)..................... ...................................1  
............JMD18-320-02 ............. Special Arbor Bolt (not shown)........................... ...................................1  
............JMD18-36701............... Capacitor (not shown)........................................ 30MF 300V.................1  
............BD1325R-X02.............. Centrifugal Switch (not shown)........................... ...................................1  
............JMD18-AP ................... Accessory Package (not shown) * ..................... ...................................1  
* Contents of the Accessory Package:  
............JMD18-020 ...................... Cutter Arbor................................................... .................................1  
............JMD18-022 ...................... Handle........................................................... .................................4  
............JMD18-039 ...................... Handle Rod ................................................... .................................3  
............JMD18-040 ...................... Knob.............................................................. .................................3  
............JMD18-050 ...................... Lock Handle .................................................. .................................1  
............561704............................. Drill Chuck..................................................... .................................1  
............JMD18-086 ...................... Cutter ............................................................ .................................1  
............JMD18-021 ...................... Chuck Arbor .................................................. .................................1  
............365534............................. Angle Vise..................................................... .................................1  
............JMD18-058 ...................... Handle Crank ................................................ .................................1  
............JMD18-201 ...................... Wheel............................................................ .................................3  
............TS-152704 ....................... Hex Wrench .................................................. 3mm.........................1  
............TS-152705 ....................... Hex Wrench .................................................. 4mm.........................1  
............TS-152706 ....................... Hex Wrench .................................................. 5mm.........................1  
............TS-0209051 ..................... Hex Socket Cap Screw.................................. 3/8x1 ........................1  
............TS-0680041 ..................... Flat Washer................................................... 3/8............................1  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
JMD-18 Table, Base, and Column Assembly  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts List for the JMD-18 Mill/Drill  
Table, Base, and Column Assembly  
Index  
No.  
Part  
No.  
Description  
Size  
Qty.  
601.........JMD18-228 ............... Table................................................................. 31L.............................1  
602.........JMD18-229 ............... Fixed Block........................................................ ...................................2  
603.........JMD18-230 ............... Movable Ring .................................................... ...................................2  
604.........TS-0207021.............. Hex Socket Head Screw.................................... 1/4”x1/2”.....................2  
605.........JMD18-368 ............... Oil Ball .............................................................. 1/4”.............................5  
606.........JMD18-201 ............... Table Handle Wheel.......................................... ...................................3  
606-1......TS-0267041.............. Set Screw.......................................................... 1/4”x3/8”.....................3  
607A.......JMD18-201A............. Handle Assembly............................................... ...................................3  
607-1......JMD18-201-1 ............ Hex Socket Head Screw.................................... 3/8”x16UNC................3  
607-2......JMD18-201-2 ............ Knob.................................................................. ...................................3  
607-3......JMD18-201-3 ............ Hex Nut ............................................................. 3/8”.............................3  
609.........JMD18-220 ............... Table Clutch ...................................................... ...................................1  
610.........JMD18-366 ............... Pin..................................................................... 5x38 ...........................1  
611.........JMD18-222 ............... Left Flange ........................................................ ...................................1  
612.........TS-0208062.............. Hex Socket Head Screw.................................... 5/16”x1”......................6  
613A.......JMD18-223A............. Table Nut Set .................................................... ...................................1  
613-1......JMD18-223 ............... Table Nut........................................................... TM23.7-10..................1  
613-2......TS-1502041.............. Cheese Head Mach Screw................................. M5x16 ........................1  
613-3......TS-1550031.............. Flat Washer....................................................... M5..............................1  
616A.......JMD18-224A............. Table Screw Assembly ...................................... ...................................1  
616-1......JMD18-224 ............... Table Lead Screw.............................................. ...................................1  
616-2......BB-51103.................. Thrust Bearing................................................... 51103 .........................2  
616-3......JMD18-226 ............... Right Flange...................................................... ...................................1  
616-4......JMD18-202-1 ............ Graduated Dial .................................................. ...................................1  
616-5......JMD18-202 ............... Dial Clutch......................................................... ...................................1  
616-6......JMD18-366 ............... Pin..................................................................... 5x38L .........................1  
617.........JMD18N-617............. Link Screw......................................................... ...................................2  
618.........JMD18-121 ............... Link Plate .......................................................... ...................................2  
619.........JMD18-204-2 ............ Rivet.................................................................. 2mm...........................4  
620.........JMD18-216 ............... Center Base....................................................... 31L.............................1  
621.........JMD18-219 ............... Antidust Plate .................................................... ...................................1  
622.........JMD18-217 ............... Antidust Plate Assembly .................................... ...................................1  
623.........JMD18-227 ............... Gib Strip............................................................ 31L.............................1  
625.........JMD18-214 ............... Fixed Block........................................................ ...................................1  
626.........TS-0051011.............. Hex Head Screw................................................ 51/6”X1/2”...................4  
627.........JMD18-212 ............... Gib Strip Bolt..................................................... ...................................2  
628.........JMD18N-628............. Bushing ............................................................. ...................................4  
629.........JMD18-213-1 ............ Locking Handle.................................................. ...................................2  
630.........JMD18-213 ............... Leaf Screw ........................................................ ...................................2  
631.........TS-0208061.............. Hex Socket Head Screw.................................... 5/16”X1”......................2  
632.........TS-0051101.............. Hex Socket Head Screw.................................... 5/16”x2-1/4”................1  
633A.......JMD18-215A............. ACME Nut Assembly ......................................... ...................................1  
633-1......JMD18-215 ............... ACME Nut ......................................................... TM23..........................1  
633-2......TS-1550031.............. Flat Washer....................................................... M5..............................1  
633-3......TS-1502041.............. Hex Socket Head Screw.................................... M5x16 ........................1  
634.........JMD18N-634............. Base.................................................................. ...................................1  
635A.......JMD18-205A............. ACME Nut Assembly ......................................... ...................................1  
635-1......JMD18-205 ............... Cross Lead Screw ............................................. TM23..........................1  
635-2......BB-51103.................. Thrust Bearing................................................... 51103 .........................2  
635-3......JMD18-204 ............... Square Flange................................................... ...................................1  
635-4......JMD18-202-1 ............ Graduated Dial .................................................. ...................................1  
635-5......JMD18-202 ............... Dial Clutch......................................................... ...................................1  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
No.  
Part  
No.  
Description  
Size  
Qty.  
635-6......JMD18-366 ............... Pin..................................................................... 5x38 ...........................1  
636.........JMD18N-636............. Column Base..................................................... ...................................1  
637.........JMD18N-637............. Rack.................................................................. 600.5L ........................1  
638.........JMD18-211 ............... Column Cap ...................................................... ...................................1  
638-1......TS-0270021.............. Set Screw.......................................................... 5/16”x5/16” .................1  
640.........JMD18-209 ............... Column Flange Ring.......................................... ...................................1  
641.........TS-0071051.............. Hex Cap Bolt ..................................................... 5/8”x2-1/2”..................4  
642.........TS-0720131.............. Lock Washer ..................................................... 5/8”.............................4  
643.........TS-0208022.............. Hex Socket Head Screw.................................... 5/16”x1/2”...................2  
644.........JMD18N-644............. Lock Washer ..................................................... 5/16”...........................3  
645.........JMD18N-645............. Plug................................................................... PT1/4”x3/8” ................1  
646.........365534...................... Vise................................................................... ...................................1  
647.........365534-01................. Hardware Package ............................................ ...................................2  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
JMD-18PFN Power Feed Assembly  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts List for the JMD-18PFN  
Power Feed Assembly  
Index  
No.  
Part  
No.  
Description  
Size  
Qty.  
248.........290111...................... Main Pulley........................................................ ...................................1  
249.........JMD18PFN-249 ........ Set Screw.......................................................... 1/4”x3/8”.....................2  
...............291022AS................. Complete Gear Box Assembly........................... ...................................1  
401-1......291022A ................... Gear Box .......................................................... ...................................1  
401-2......BB-6003ZZ ............... Bearing.............................................................. 6003ZZ.......................4  
401-3......2450082A ................. Change Gear Lever ........................................... ...................................1  
401-4......2450084B ................. Tension Spring .................................................. ...................................1  
401-5......JMD18PFN-360 ........ Pin..................................................................... ...................................2  
401-6......2450083A ................. Stop................................................................... ...................................1  
401-7......2450089A ................. Collar................................................................. ...................................1  
401-8......TS-1523011.............. Set Screw.......................................................... M6x6 ..........................2  
401-9......2450074A ................. Spacer............................................................... ...................................4  
401-10....2450072A ................. Gear.................................................................. ...................................1  
401-11....2450071A ................. Gear.................................................................. ...................................1  
401-12....2450070A ................. Gear.................................................................. ...................................1  
401-13....291026A ................... Shaft.................................................................. ...................................1  
401-14....JMD18PFN-269 ........ Key.................................................................... 5x5x25 .......................1  
401-15....291047...................... Worm Gear ....................................................... ...................................1  
401-16....TS-1523011.............. Set Screw.......................................................... M6x6 ..........................2  
401-17....JMD18PFN-282 ........ C-Ring .............................................................. R35 ............................2  
401-18....2450014.................... Cover ................................................................ ...................................2  
401-19....2450079.................... Speed Knob....................................................... ...................................1  
401-20....JMD18PFN-303 ........ Round Head Screw............................................ M4x25 ........................1  
401-21....290089...................... Spring................................................................ ...................................1  
401-22....SB-5/16..................... Steel Ball........................................................... 5/16”...........................1  
401-23....2450051.................... Pin..................................................................... ...................................1  
401-24....2450020.................... Release Block.................................................... ...................................1  
401-25....JMD18PFN-373 ........ C-Ring............................................................... S19.............................1  
401-26....2450077A ................. Gear.................................................................. ...................................1  
401-27....2450076A ................. Gear.................................................................. ...................................1  
401-28....2450075A ................. Gear.................................................................. ...................................1  
401-29....291028A ................... Transmission Worm........................................... ...................................1  
401-30....JMD18PFN-358 ........ Key.................................................................... 5x5x32 .......................1  
401-31....291027A ................... Pinion................................................................ ...................................1  
401-32....JMD18PFN-369 ........ C-ring ................................................................ S15.............................1  
401-33....2450057.................... Bushing ............................................................. ...................................1  
401-34....2450054.................... Spring................................................................ ...................................1  
401-35....291046...................... Worm Shaft....................................................... ...................................1  
401-36....TS-1523011.............. Set Screw.......................................................... M6x6 ..........................2  
401-37....291050...................... Clutch Block ...................................................... ...................................1  
401-38....BB-6003ZZ ............... Ball Bearing....................................................... ...................................2  
401-39....JMD18PFN-262 ........ Key ................................................................... 5x5x10 .......................1  
401-40....291023A ................... Transmission Shaft............................................ ...................................1  
401-41....JMD18PFN-389 ........ Key ................................................................... 5x5x45 .......................1  
401-42....291024A ................... Bearing Housing ................................................ ...................................1  
401-43....TS-0720071.............. Lock Washer ..................................................... 1/4”.............................3  
401-44....TS-0207041.............. Hex Socket Cap Screw...................................... 1/4”x3/4”.....................3  
401-45....JMD18PFN-255 ........ C-Ring............................................................... S17.............................1  
402.........291032A ................... Base.................................................................. ...................................1  
...............291029AS................. Complete Worm Gear Assembly ....................... ...................................1  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
No.  
Part  
No.  
Description  
Size  
Qty.  
403-1......2450048.................... Worm Gear Cover............................................. ...................................1  
403-2......JMD18PFN-346 ........ Flat Cross Head Screw...................................... M4x4 ..........................3  
403-3......JMD18PFN-320 ........ C-Ring............................................................... S25.............................1  
403-4......2450024.................... Clutch Gear Case .............................................. ...................................1  
403-5......2450026.................... Clutch Key......................................................... ...................................2  
403-6......2450025.................... Clutch Key Pin................................................... ...................................2  
403-7......2450028.................... Spring................................................................ ...................................2  
403-8......2450027.................... Spring Pin.......................................................... ...................................2  
403-9......2450023.................... Worm Gear ....................................................... ...................................1  
403-10....2450022.................... Key.................................................................... ...................................2  
403-11....291029A ................... Pinion Shaft....................................................... ...................................1  
404.........JMD18PFN-250 ........ Flat Head Screw................................................ 3/16”x3/8”...................1  
405.........TS-0208061.............. Hex Socket Cap Screw...................................... 5/16”x1-1/4”................3  
406.........291049...................... Bearing Spacer.................................................. ...................................1  
...............291030AS................. Complete Clutch Bushing Assembly .................. ...................................1  
407-1......291030A ................... Clutch Bushing .................................................. ...................................1  
407-2......2450030.................... Bushing Pin ....................................................... ...................................1  
407-3......2450031.................... Bushing Stop ..................................................... ...................................1  
407-4......2450032A ................. Scale Base ........................................................ ...................................1  
407-5......JMD18PFN-326 ........ Pin..................................................................... ...................................1  
407-6......2450037.................... Hub ................................................................... ...................................1  
407-7......2450039.................... Pin..................................................................... ...................................2  
407-8......2450033.................... Scale Base Set Screw ....................................... ...................................1  
407-9......2450038.................... Handle............................................................... ...................................2  
407-10....2450063.................... Graduated Base Handle..................................... ...................................1  
407-11....H02050..................... Hex Nut ............................................................. 5/16”...........................1  
407-12....2450098.................... T-Screw............................................................. 5/16”x3/4”...................1  
408.........JMD18PFN-350 ........ Hex Socket Cap Screw...................................... 5/16”x3-1/2”................3  
409.........2450060.................... Pointer............................................................... ...................................2  
410.........JMD18PFN-309 ........ Rivet.................................................................. ...................................4  
411.........JMD18PFN-354 ........ Speed Scale...................................................... ...................................1  
412.........6145 ......................... Worm Cover...................................................... ...................................1  
413.........JMD18PFN-376 ........ Hex Socket Cap Screw...................................... 3/16”x3/8”...................2  
414-1......291051A ................... Micro Adjusting Indicator ................................... ...................................1  
414-2......TS-0267031.............. Set Screw.......................................................... 1/4”x5/16”...................1  
...............6142-2S .................... Complete Wheel Assembly................................ ...................................1  
416-1......6142-2 ...................... Hand Wheel ...................................................... ...................................1  
416-2......6580 ......................... Handle............................................................... ...................................1  
416-3......6581 ......................... Handle Screw .................................................... ...................................1  
416-4......TS-0270021.............. Set Screw.......................................................... 5/16”x5/16” .................1  
418-1......290110...................... Sub-Pulley......................................................... ...................................1  
418-2......TS-0267031.............. Set Screw.......................................................... 1/4”x5/16”...................1  
420.........JMD18PF-114........... Belt.................................................................... ...................................1  
421.........290086...................... Knob.................................................................. ...................................2  
422.........2450040.................... Washer.............................................................. M8..............................1  
423.........TS-1504031.............. Hex Socket Cap Screw...................................... M8x16 ........................1  
...............291001-CPN ............. Gear Box Assembly Complete .......................... ...................................1  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wiring Diagram JMD-15  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wiring Diagram JMD-18 230V Only  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Infinite Peripherals Scanner IP BC BT User Manual
Insignia Computer Keyboard NS PNK5011 User Manual
John Deere Compact Loader 160G LC User Manual
JVC Portable CD Player RC BZ6BU User Manual
Kenwood Juicer AT265 User Manual
Kenwood Marine Radio TM 261A User Manual
Kenwood Motorcycle Accessories R 1000 User Manual
Kenwood Work Light NXR 710 User Manual
Keurig Coffeemaker B44 User Manual
Kicker Speaker CVT12 User Manual