DVDB01
DVD/CD/MP3 Player
Installation and Operation Manual
DVD VCD
WMA MP3
CD
CLASSIC POP ROCK
DTS EQ
TRACK TITLE CHAPTER
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
PREPARATION
It’s a good idea to read all of the instructions before beginning the installation. We recommend
having your JENSEN DVDB01 installed by a reputable installation shop.
Tools and Supplies
You will need these tools and supplies to install your DVDB01:
•
•
•
•
•
•
•
•
•
Torx type, flat-head and Philips screwdrivers
Wire cutters and strippers
Tools to remove existing radio (screwdriver, socket wrench set or other tools)
Electrical tape
Crimping tool
Volt meter/test light
Crimp connections
18 gauge wire for power connections
16 – 18 gauge speaker wire
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable
prior to installation.
NOTE: If the DVDB01 is to be installed in a vehicle equipped with an on-board drive or
navigation computer, do not disconnect the battery cable. If the cable is disconnected, the
computer memory may be lost. Under these conditions, use extra caution during
installation to avoid causing a short circuit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
INSTALLATION
DIN Front-Mount Installation
1. Use the supplied release keys to remove the half-sleeve from the unit.
CAUTION! Be careful not to damage the vehicle’s wiring.
3. Place the unit in front of the dashboard opening so the wiring can be brought through the
mounting sleeve.
4. Complete wiring connections (see “Wiring” on page 7).
5. After completing the wiring connections, turn the unit on to confirm operation (ignition switch
must be on). If unit does not operate, recheck all wiring until problem is corrected. Once the
unit is properly operating, turn off the ignition switch and proceed with final mounting of the
chassis.
6. Carefully slide the DVD player into the half-sleeve making sure it is right-side-up until it is fully
seated and the spring clips lock it into place.
D
V
D
M
B
0
O
1
D
E
D
V
D
/C
D
/M
P
3
P
NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30°
of horizontal. Make sure the unit is mounted within this limitation.
L
A
Y
E
R
M
U
TE
V
ID
E
O
IN
2
L
A
U
7. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the
chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure
part of the dashboard either above or below the unit using the screw and hex nut provided.
Bend the strap to position it as necessary.
2. Install the half-sleeve.
a. Install adapter if necessary (optional).
CAUTION! The rear of the unit must be supported with the strap to prevent damage to the
dashboard from the weight of the unit or improper operation due to vibration.
b. Install half-sleeve into adapter or dashboard using the supplied screws. Do not force the
sleeve into the opening or cause it to bend or bow.
c. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.
With the sleeve fully inserted into the dashboard opening, bend as many of the tabs
outward as necessary to firmly secure the sleeve to the dashboard.
8. Replace any items you removed from the dashboard.
Install Half-Sleeve
2c
2a
2b
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
DIN Rear-Mount Installation
DIN Front-Mount Installation
7
8
DV
DB01
M
O
D
E
D
V
D
/C
D
/M
P
3
P
L
A
Y
E
R
M
U
T
E
V
ID
E
2
O
IN
2
L
A
U
D
IO
IN
2
R
1
4
DVD
B01
M
O
D
E
D
V
D
/C
D
/M
P
3
P
L
A
Y
E
R
M
U
T
E
V
ID
E
O
IN
2
L
A
U
D
IO
3
IN
2
R
3
Reconnecting the Battery
When wiring is complete, reconnect the battery negative terminal.
DIN Rear-Mount Installation
With some vehicles, you can use the screw holes located on both sides of the unit to fasten the
unit to the factory radio mounting brackets supplied with your vehicle. To install this unit using
factory mounting plates, perform the following steps:
Removing the Unit
1. Make sure the ignition is turned off, then disconnect the cable from the vehicle battery’s
1. Remove trim ring.
negative (-) terminal.
2. Remove the metal strap attached the back of the unit (if attached).
3. Lift the top of the outer trim ring then pull it out to remove it.
NOTE: The outer trim ring, sleeve and the metal strap are not used for DIN rear-mount
installation.
4. Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then
pull the unit out of the dashboard.
2. Align the screw holes on the bracket with the screw holes on the unit, then tighten the screws
(5x5mm) on each side.
3. Reinstall the dash panel.
Removing the Unit
D
V
D
B
0
1
M
O
DE
D
VD
/C
D
/M
P
3
P
LA
Y
ER
M
U
T
E
V
ID
EO
IN
2
L
AU
R
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
WIRING
Power/Accessory Connections
1
7
WIRED REMOTE
1. P.A. – Connect to PADIN5.
2. REMOTE CONTROL EXTENDER – Position extender where you are
likely to use the remote control. Point remote at eye to control the unit.
3. CONSTANT POWER WIRE (yellow) – Connect the 12V PLUS constant
power wire to a live 12 volt wire in the vehicle. Before making a
connection, check that the wire you intend to connect it to is always live,
even when the car’s ignition is turned off. If a live wire is not found, route
the wire to the car’s fuse block and connect it to a live circuit there.
4. ACC POWER WIRE (red) – Connect to a +12 volt circuit that is only live
when the ignition is on. The best connection point is at the car’s fuse block
at the “RADIO” or “ACCESSORY” identified terminals.
5. GROUND WIRE (black) – Securely fasten the Ground wire to a grounded
metal part of the car’s chassis. If you cannot find an existing bolt or screw
to fasten it to, drill a hole in the metal and secure it with a screw. To
ensure a good ground, remove any paint or grease from areas where the
wire will contact the surface.
6. DC12V OUT – Provides 12VDC at 300mA when DVD is on.
7. Connect optional wired remote control.
2
IR REMOTE CONTROL EXTENDER EYE
6
POWER WIRING HARNESS
+
3
3A FUSE
YELLOW
4
BLACK
1A FUSE
5
RED
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
Audio/Video Connections
NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging
the DVD player. The DVDB01 uses one 3 amp and one 1 amp ACC fuse, located in line with
the power wires.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
CONTROLS AND INDICATORS
The buttons located on the unit and the remote control that perform the same function are
assigned the same number for reference on the diagrams and in the text.
Remote Control Operation
Front Panel Operation
3
1
MENU
2
12
3
8
1
24
38
4
19
SHUFFLE
7
33
29
30
EQ
ENTER
34
DVD VCD
WMA MP3
CD
8
35
CLASSIC POP ROCK
TRACK TITLE CHAPTER
DTS EQ
VOL
21
VOL
6
5
9
T/F
31
10
16
11
7
5
9
4
6
13
14
15
18
32
20
PROG
LANG
RPT
TITLE
MODE
1. Power
11
26
23
37
2. Infrared Sensor
3. Eject
ZOOM
ANGLE
GOTO
4. Fast Forward/Advance Chapter
5. Stop
36
6. Pause/Play/Mute
7. Rewind/Previous Chapter
8. Volume Up
28
27
SEL
9. Volume Down
10. Select
10
17
25
22
11. Mode
12. Disc Slot
13. Video In
14. Left Audio In
15. Right Audio In
16. Reset
Using the Remote Control
Point the remote control towards the player front face remote sensor IR (2). The operation angle is
approximately 30 degrees in each direction of the front of the remote sensor.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
Remote Control Functions
Ref # Button
Function
33
34
35
36
37
38
EQ
Select the equalization mode, such as CLASSIC, POP, ROCK
Search in reverse rapidly
Ref # Button
Function
<</TRACK
>>/TRACK
0-9
1
Turn the unit ON or OFF
/POWER
Search forward rapidly
3
4
5
Eject the disc
/EJECT
Enter track/chapter number directly. Use GOTO to search.
Used with numeric buttons to search disc
Press to mute/resume audio.
>>|/TRACK
Skip to the next track/chapter
Stop disc playback
GOTO
6
>||
Play/pause the disc (for disc play mode)
Go to previous track/chapter
7
|<</TRACK
VOL /\
VOL \/
SEL
8
Increase the volume level
9
Decrease the volume level
10
11
Select the desired adjustment mode. Press VOL+/- to change settings.
MODE
Change between disc (DVD/VCD/CD/MP3) play mode and AV IN1 or AV
IN2 mode
17
18
Display statistical disc information during playback
PROG
Display programmed playback screen, allowing you to enter tracks to play
in programmed order.
19
20
21
SHUFFLE
RPT
Play tracks in random order (NOT for DVD)
Repeat current track/chapter
T/F
Press and hold to set clock. Use track down to adjust hours and track up to
adjust minutes.
22
Change the SUBTITLE language on multi-subtitle language DVD discs
Change the viewing angle on multi-angle DVD discs
23
24
ANGLE
MENU (PBC) Display the root menu stored on DVD discs/Switch between PBC ON and
PBC OFF on VCD discs
25
Display the SETUP menu
26
27
28
29
30
31
ZOOM
10+
Increase the picture size
Use to select a digit for the tens position when performing track/file search.
10/0
<, > /\, \/
ENTER
LANG
Select items left/right and ahead/back in menu mode
Confirm selection of track/chapter
Change the audio sound track on multi-audio sound track DVD discs.
Change the sound mode of VCD discs
32
TITLE
Display the TITLE menu stored on DVD disc
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
BASIC OPERATION
Turning the Unit On/Off
Equalization
Press the EQ button (33) on the remote control to activate the equalization function. Continue
pressing the EQ button to choose between the three equalizer modes (CLASSIC, POP and
ROCK) or to turn the equalizer function off (DSP OFF).
Press the POWER button (1) on the front panel or remote control to turn the unit on/off.
Inserting a Disc
Insert a disc, label side up, into the disc slot (12). The player will start playback automatically.
Reset
Ejecting a Disc
The RESET button (16) is located on the front of the unit. You should engage the RESET button
only in the following situations:
Press the EJECT button (3) to eject the disc from the slot. The unit does not have to be on to eject
a disc.
•
•
•
After initial installation when all wiring is complete
If all function buttons become inoperable
If an error symbol appears on the display
NOTE: Do not drive with an ejected disc in the slot.
To reset the unit, use a ballpoint pen or a thin metal object to depress the RESET button.
Audio Control
AV In Operation
You can connect another audio/video system to the unit through the AV IN terminals on the back
(AV1 INPUT) or front panel (AV2 INPUT) of the unit. Once the device is connected, press the
MODE button (11) on the front panel or remote control to select “AV IN1” or “AV IN2” mode.
Volume
Press the VOL /\ button (8) to increase the volume, or the VOL \/ button (9) to decrease the
volume.
Mute
Press the MUTE button (6) to silence the audio. Press MUTE again to resume audio.
Press the SEL button (10) on the front panel or remote control to select the desired audio
adjustment mode. The adjustment mode will change in the following order:
Bass
Press SEL until “BAS” appears in Press the volume buttons to adjust the Bass from +06 to -06.
the display.
Treble
Balance
Press SEL until “TRE” appears in Press the volume buttons to adjust the Treble from +06 to -06.
the display.
Press SEL until “BAL” appears in Press the volume buttons to adjust the Balance from 12L to
the display.
12R.
Clock Display
Press the T/F button (21) to alternate between playing time and clock time.
Setting the Clock
Press and hold the T/F button (21) on the remote until the clock display flashes, and then release.
Next, press < (29) or |<< (7) to adjust the hour and > (29) or >>| (4) to adjust the minutes. Continue
changing the hour to move between AM and PM.
Mode
Press the MODE button (11) on the front panel or remote control to switch between disc (DVD/
VCD/CD/MP3) mode, AV IN1, or AV IN2 mode.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
CD/DVD/VCD OPERATION
Repeating Playback
2
12
3
8
Press the RPT button (20) on the remote control to select the repeat mode as follows:
1
DVD: CHAPTER > TITLE > REP ALL > OFF
VCD/CD: REP 1 > REP ALL > OFF
•
•
•
•
Select CHAPTER to continuously repeat the current chapter.
Select TITLE to continuously repeat the current title.
Select REP 1 to continuously repeat the current track.
Select REP ALL to continuously repeat all chapters/tracks on the current disc. After playing
the last chapter/track, the unit will stop and display the elapsed time.
DVD VCD
WMA MP3
CD
CLASSIC POP ROCK
TRACK TITLE CHAPTER
DTS EQ
NOTE: The REPEAT feature does not support VCD 2.0 (with PBC ON).
PBC (Play Back Control) (VCD Only)
10
16
11
7
5
9
4
6
13
14
15
For VCDs with play back functionality, play back control (PBC) provides additional controls for
VCD playback.
Press the MENU button (24) on remote control to toggle the PBC function “On”/”Off”. Once PBC is
on, playback starts from track one of the play list.
Stopping Play
•
Press the stop
button (5) on the front panel or remote control to stop disc play. Press the
>|| button (6) to resume normal playback.
NOTE: During VCD playback you can press the LANG button (31) on the remote control
during playback to switch the sound between mono and stereo sound in the following
order: MONO LEFT > MONO RIGHT > STEREO.
•
Press the stop
button (5) on the front panel or remote control twice to stop the playback
and return to the initial chapter.
Moving Through Chapters/Tracks
Zooming
•
Press the >>| button (4) on the unit or remote control to advance to the next chapter/track.
The Zoom function allows you to increase the picture size. Press the ZOOM button (26) on the
remote control to toggle from 2X to 3X to 4X scale and then to 1/2, 1/3 and 1/4 scale. When the
scale is 1/4X, press ZOOM again to select OFF and cancel the Zoom function.
•
Press the |<< button (7) on the unit or remote control to move to the previous chapter/track.
Fast Forward/Fast Backward
Press the >> button (35) on the remote control to fast forward. Keep pressing and releasing the
button to increase the rate from “2X” to “4X”, “8X” and “20X”. Press the >|| button (6) to return to
regular playback. Press and hold to fast-forward to a specific location. Release to begin playback
from that point.
During Zoom mode, press the arrow (<, >, /\, \/) buttons (29) to move the picture up, down, left, or
right.
Random Play (CD/VCD Only)
Press the SHUFFLE button (19) on the remote control to select and play tracks in random order.
The display will show “RANDOM”. Press the >|| button to begin the shuffled playback. Press the
SHUFFLE button again to turn shuffle off.
Press the << button (34) on the remote control to fast backward. Keep pressing and releasing the
button to increase the rate from “2X” to “4X”, “8X”, and “20X”. Press the >|| button (6) to return to
regular playback. Press and hold to fast backward to a specific location. Release to begin
playback from that point.
Remote Control Direct Track Entry
Pausing Playback
Press the >|| button (6) on the unit or the >|| button on the remote control during playback to
temporarily stop playback. To return to normal playback, press the >|| button again.
To select a track directly, use the number pad on the remote control (36). For single digit entries,
press the corresponding number. For two digit entries, press the 10+ button (27) followed by the
last digit (i.e., for track 16, press 10+ and then 6).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
Goto Search
On-Screen Display Function
During DVD or VCD playback, perform the following steps to use the GOTO feature to access a
specific location on a disc:
Press the display (
screen.
) button (17) during playback to view playback information at the top of the
Title/Chapter Search
DVD Playback Information
To play a specific title/chapter:
The following information is displayed at the top of the screen during DVD playback:
1. Press the GOTO button (37) button. The On Screen Display information will appear with the
track/chapter number highlighted (TRK 00/00).
2. Use the arrow (<, >, /\, \/) buttons (29) to move the cursor to the time field.
3. Use the numeric buttons (36) on the remote control to enter the desired title/chapter number.
4. Press the ENTER button (30).
•
•
TT 5/8 – “5 / 8" indicates the fifth of 8 titles on the DVD is currently playing.
CH 2/16 – “2 / 16" indicates that the second of 16 chapters on the DVD is currently playing.
Time Search
To enter an exact playback starting point:
1. Press the GOTO button (37).
•
Press
repeatedly to view the following information: for elapsed/remaining playing time:
•
00:02:18 – total elapsed playing time for disc
2. When the On Screen Display information appears at the top of the screen, use the arrow (<,
>, /\, \/) buttons (29) to move the cursor to the time field (00:00:00).
•
•
•
C –00 :34 :37 – remaining playing time
T 00:02:18 – total elapsed playing time for current track
C –00 :34 :37 – remaining playing time for current track
3. Use the numeric buttons (36) on the remote control to enter the playback starting point.
4. Press the ENTER button (30).
•
•
•
•
1/5 ENG – English is the selected audio language out of 5 possible choices
5.1 CH – The current language is recorded in 5.1 surround sound
1/4 ENG – English is the selected subtitle language out of 4 possible choices
OFF – There are no alternate angles recorded for this scene
Playing in Programmed Order (CD/VCD)
1. Press the PROG button (18) to access the programmed playback screen:
PROGRAM
VCD Playback Information
The following information is displayed at the top of the screen during VCD playback:
•
•
TRK ##/## – “1/18” indicates the first of 18 tracks on the VCD is currently playing.
PBC: Indicates when PBC (Playback Control) is turned on.
•
– “X” indicates repeat play is OFF, “1” indicates repeat track, “D” indicates repeat
directory, and “A” indicates repeat disc.
2. Use the arrow (<, >, /\, \/) buttons (29) on the remote control to access the fields on the
“PROGRAM” screen.
3. Use the number buttons on the remote control to enter a track number in each field.
4. Press the >/|| button (6) on the remote control or highlight “PLAY” on screen and then press
the ENTER button (30) to begin playback in the numbered order indicated.
1. To delete the list, highlight “CLEAR” and then press ENTER. Press PROG to exit the
programmed playback screen.
•
Press
repeatedly to view the following information for elapsed/remaining playing time:
•
00:02:18 – total elapsed playing time for disc
•
•
•
C –00 :34 :37 – remaining playing time
T 00:02:18 – total elapsed playing time for current track
C –00 :34 :37 – remaining playing time for current track
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
CD Playback Information
The following information is displayed at the top of the screen during CD playback:
•
•
TRK ##/## – “1/18” indicates the first of 18 tracks on the CD is currently playing.
– “X” indicates repeat play is OFF, “1” indicates repeat track, and “A” indicates repeat
disc.
•
Press
repeatedly to view the following information for elapsed/remaining playing time:
•
00:02:18 – total elapsed playing time for disc
•
•
•
C –00 :34 :37 – remaining playing time
T 00:02:18 – total elapsed playing time for current track
C –00 :34 :37 – remaining playing time for current track
Multi-Language Discs (DVD Only)
Changing Audio Language
If you are watching a disc recorded in multiple languages, press the LANG button (31) on the
remote control to choose a language. If no other languages are recorded, “INVALID KEY” is
displayed in the top left corner of the screen.
Changing Subtitle Language
If you are watching a disc recorded in multiple languages with subtitles, press the
button (22)
on the remote control to choose the language in which you would like the subtitles to appear. If no
other languages are available, “INVALID KEY” is displayed in the top left corner of the screen.
Menu Function (DVD Only)
Press the MENU button (24) on the remote control while the disc is playing to display the disc root
menu. You can navigate with the remote control navigation keys and select a feature with the
ENTER button (30) on the remote control.
Title Menu Function (DVD Only)
If the DVD has multiple titles recorded on the disc, you can select a specific title from the title menu
from which to start playback.
1. Press the TITLE button (32) on the remote control during playback to display the title menu.
2. Select the preferred title using the remote control arrow keys (29) and confirm by pressing the
ENTER (30) button.
Viewing an Alternate Picture Angle (DVD Only)
Some DVDs contain scenes that have been shot simultaneously from different angles. For discs
recorded with multiple angles, press the ANGLE button (23) on the remote control to toggle
available angles of the on-screen image. If no other angles are recorded, “INVALID KEY” is
displayed in the top left corner of the screen.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
MP3 OPERATION
Select one of these icons to access the corresponding media on your disc or USB device. If the
media type is not present, the icon will not be selectable.
2
12
3
8
1
•
•
: Audio
: Photos
•
: Video
DVD VCD
WMA MP3
CD
Stopping Play
CLASSIC POP ROCK
•
•
Press the stop
Press the >|| button (6) to resume normal playback.
button (5) on the front panel or remote control to stop disc play.
TRACK TITLE CHAPTER
DTS EQ
•
Press the stop
button (5) on the front panel or remote control twice to stop the playback
and return to the initial chapter.
Moving Through Chapters/Tracks
10
16
11
7
5
9
4
6
13
14
15
•
Press the >>| button (4) on the unit or remote control to advance to the next chapter/track.
•
Press the |<< button (7) on the unit or remote control to move to the previous chapter/track.
Insert/Eject Disc
Insert a disc label-side up into the disc slot (12), and the disc will begin to play. Press the eject button (3)
to stop playback and eject the disc.
File/Folder Navigation
Press the arrow (<, >, /\, \/) buttons (29) to navigate the-onscreen display to choose folders/files
when playing and MP3 disc. Press the ENTER button (30) to select.
Fast Forward/Fast Backward
NOTE: MP4 streaming video format is not supported.
Press the >> button (35) on the remote control to fast forward. Keep pressing and releasing the
button to increase the rate from “2X” to “4X”, “8X” and “20X”. Press the >|| button (6) to return to
regular playback. Press and hold to fast-forward to a specific location. Release to begin playback
from that point.
MP3 Monitor Display
After loading an MP3 disc, the following screen will appear on your output monitor.
Press the << button (34) on the remote control to fast backward. Keep pressing and releasing the
button to increase the rate from “2X” to “4X”, “8X”, and “20X”. Press the >|| button (6) to return to
regular playback. Press and hold to fast backward to a specific location. Release to begin
playback from that point.
[ - ]PHISH
—
GUMBO.MP3
01. -
02. 80'S
01. CHERRY POP
02. CHRIS ISSA
03. CRAZY TOWN
Pausing Playback
Press the >|| button (6) on the unit or the >|| button on the remote control during playback to
temporarily stop playback. To return to normal playback, press the >|| button again.
03. ALLMAN BRO
04. DISCO-FUNK
05. OLDIES
04. PHISH
05. PHISH
06. PHISH
07. PHISH
—
—
—
—
BI
BO
FR
GI
Repeating Playback
Press the RPT button (20) on the remote control to select the repeat mode as follows:
08. PHISH...— GU
09. PHISH CH
—
REP 1 > REP DIR > REP ALL > OFF
•
•
•
Select REP 1 to continuously repeat the current file.
Select REP DIR to to continuously repeat the current directory/folder.
Select REP ALL to continuously repeat all files on the current disc. After playing the last file,
the unit will stop and display the elapsed time.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
Random Playback
MP3 Playback Information
Press the SHUFFLE button (19) on the remote control to select and play tracks in random order.
The display will show “RANDOM”. Press the >|| button to begin the shuffled playback. Press the
SHUFFLE button again to turn shuffle off.
The following information is displayed at the top of the screen during CD playback:
Playing in Programmed Order
1. Press the PROG button (18) to access the programmed playback screen:
•
•
TRK ##/## – “9/150” indicates the ninth of 150 tracks on the disc is currently playing.
– “X” indicates repeat play is OFF, “1” indicates repeat song, and “D” indicates repeat
directory (folder).
PROGRAM
•
Press
repeatedly to view the following information for elapsed/remaining playing time:
•
00:02:18 – total elapsed playing time for disc
•
C –00 :34 :37 – remaining playing time for disc
2. Use the arrow (<, >, /\, \/) buttons (29) on the remote control to access the fields on the
“PROGRAM” screen.
3. Use the number buttons on the remote control to enter a file number in each field.
4. Press the >/|| button (6) on the remote control or highlight “PLAY” on screen and then press
the ENTER button (30) to begin playback in the numbered order indicated.
5. To delete the list, highlight “CLEAR” and then press ENTER. Press PROG to exit the
programmed playback screen.
Remote Control Direct File Entry
To select a file directly, use the number pad on the remote control (36). For single digit entries,
press the corresponding number. For two digit entries, press the 10+ button (27) followed by the
last digit (i.e., for file 16, press 10+ and then 6).
GOTO Direct File Access
Use the GOTO function to access a file directly.
1. Press the GOTO button (37) on the remote control. The On Screen Display information will
appear with the file number highlighted.
2. Use the number keys on the remote control to enter the 3-digit file number directly (i.e. for file
10, enter “010”.
3. Press the ENTER button to confirm and begin playback.
On-Screen Display Function
Press the display (
screen.
) button (17) during playback to view playback information at the top of the
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
DVD SETUP MENU
RATING: Select the parental control level for all DVD play. The security password is required to
make changes to this feature.
Press the
(setup) button (29) on the remote control to access the SYSTEM SETUP menu and
adjust system settings for the following categories:
DEFAULT: Use this item to restore default settings at any time.
•
•
•
•
•
System Setup
Language Setup
Audio Setup
Video Setup
Digital Setup
Language Setup
The Language Setup menu controls the
following features:
Use the arrow (<, >) buttons (29) to choose between SYSTEM, LANGUAGE, or VIDEO setup
options.
LANGUAGE SETUP
ENGLISH
GERMAN
SPANISH
FRENCH
OSD LANGUAGE
AUDIO LANG
While in the setup menus, use the (<, >, /\, \/) buttons (29) to select and change settings. The “up”
and “down” arrows highlight the options, and the “right” and “left” arrows will change the setting for
the highlighted option.
SUBTITLE LANG
MENU LANG
System Setup
The System Setup menu controls the
following features:
SYSTEM SETUP
AUTO
NTSC
PAL
TV SYSTEM
SCREEN SAVER
TV TYPE
On-Screen Display (OSD) Language: Set the OSD language to one of the following: English,
German, Spanish or French.
PASSWORD
RATING
Audio Language: Set the audio language to one of the following: Chinese, English, Japan, French,
Spanish, Russian, Latin or German.
Subtitle Language: Set the subtitle language to one of the following: Chinese, English, Japan,
French, Spanish, Russian, German or OFF.
DEFAULT
Menu Language: Set the menu language to one of the following: Chinese, English, Japan, French,
Spanish, Russian, German or Latin.
TV SYSTEM: This item is used to select a TV signal system to match your TV set. Select one of
the following options: AUTO, NTSC or PAL.
SCREEN SAVER: Turn Screen Saver feature On/Off.
TV TYPE: Select one of the following picture formats: 4:3PS, 4:3LB or 16:9. 4:3 is a letterbox
selection, and 16:9 is wide screen.
•
•
•
4:3PS: Image is played back in the PAN SCAN style. (If connected to a wide-screen TV, the
left and right edges are cut off.)
4:3 LB: Image is played back in letter box style. (If connected to a wide-screen TV, black
bands appear at the top and bottom of the screen.)
16:9: Select this option when a wide-screen TV set is connected.
PASSWORD: This item allows the selection of a new four-digit code to use for security purposes.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
Audio Setup
The Audio Setup menu controls the
following features:
AUDIO SETUP
#
+4
+2
0
KEY
-2
-4
b
Key: This item changes the audio output key.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
DISC SYMBOLS AND PROPERTIES
Table 1: Disc Properties
Symbol
12cm Disc Properties
Max Play Time
(MPEG 2 Method)
133 minutes
242 minutes
266 minutes
484 minutes
Single side single layer (DVD-5)
Single side double layer (DVD-9)
Double side single layer (DVD-10)
Double side double layer (DVD-18)
(MPEG 1 Method)
74 minutes
Single side single layer (Video CD)
Single side single layer
74 minutes
74 minutes
Single side single layer
Table 2: DVD Disc Symbols
Meaning
Symbol
Number of voice languages recorded. The number inside the icon indicates the number lan-
guages on the disc (maximum of 8).
Number of subtitle languages available on the disc (maximum of 32).
Number of angles provided (maximum of 9).
Aspect ratios available. “LB” stands for Letter Box and “PS” stands for Pan/Scan. In the
example on the left, the 16:9 video can be converted to Letter Box video.
Indicates the region code where the disc can be played.
•
•
•
•
Region 1: USA, Canada, East Pacific Ocean Islands
Region 2: Japan, Western Europe, Northern Europe, Egypt, South Africa, Middle East
Region 3: Taiwan, Hong Kong, South Korea, Thailand, Indonesia, South-East Asia
Region 4: Australia, New Zealand, Middle and South America, South Pacific Ocean
Islands/Oceania
•
Region 5: Russia, Mongolia, India, Middle Asia, Eastern Europe, North Korea, North
Africa, North-West Asia
•
•
Region 6: Mainland China
ALL: All regions
NOTE: The following types of discs will not play in this unit: DVD-ROM, DVD-RAM, CDV,
CD-G. DVD-R discs WILL play in this unit.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
TROUBLESHOOTING
Problem
Cause
Corrective Action
Unit will not power on
Radio Fuse blown
Car battery fuse blown
Illegal operation
Install new fuse with correct rating
Install new fuse with correct rating
Press the RESET button located in the bottom right corner of the front panel
Replace battery with new one
Remote control does not function
Battery depleted
Battery installed incorrectly
Pirated disc is in use
Remove battery and install correctly
Use original copy
Poor sound quality or distortion
Unit resets itself when engine is off
Incorrect connection between ACC and positive battery
wire
Check wiring and correct
Cannot insert disc
Disc already inside unit
Disc is warped or scratched
Disc is dirty or wet
Eject current disc and insert new one
Use disc in good condition
Clean disc with soft cloth
Disc does not play back
Laser pickup is dirty
Clean laser pickup with cleaning disc
Use compatible disc
Incompatible disc is used
Disc region code is not compatible with unit
Disc is inserted upside down
Disc is illegally copied
Use disc with proper region code
Insert disc with label side up
Use original disc
Image blurred, distorted, or dark
PBC cannot be used during VCD playback
No repeat or searching while playing VCD
PBC is not available on the disc
PBC is on
Turn PBC off
•
•
When the vehicle warms up during cold weather or under damp conditions, condensation
may appear on the LCD panel. Should this occur, the screen will not operate properly until the
moisture has evaporated.
We suggest you use a cleaning disc in this unit more frequently than in the unit in your home
due to the environmental conditions of the vehicle.
Care and Maintenance
•
Use only a clean silicone cloth and neutral detergent to clean the front panel or monitor. A
rough cloth and non-neutral detergent (such as alcohol) may result in scratching or
discoloration.
•
•
Do not get water or cleaning fluids on the unit.
If the temperature inside the player gets too hot, a protective circuit automatically stops play
of the disc. If this occurs, allow the unit to cool before operating the player again.
Never insert anything other than a 5” (12 cm) compact disc into the player as the mechanism
can be damaged by foreign objects.
Do not attempt to use a 3” (8 cm) CD-Single disc in this unit, either with or without an adaptor,
as damage to the player and/or disc may occur. Such damage is not covered by the Warranty
on this product.
•
•
•
•
The ventilation should not be impeded by covering the ventilation openings with items such
as newspapers, table-cloths, curtains, etc.
The DVD player may not operate properly in extreme hot or cold. If such conditions occur,
allow the interior of the vehicle to reach a normal temperature before using player.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
SPECIFICATIONS
LIMITED WARRANTY
Supply Voltage: 12V DC (11V-15V), negative ground
90 Day / 12 Month Limited Warranty
Current Consumption: Less than 2A
AUDIOVOX SPECIALIZED APPLICATIONS, LLC (the Company) warrants to the original retail
purchaser of this product that should this product or any part thereof, under normal use and
conditions, be proven defective in material or workmanship within 90 days from the date of original
purchase, such defect(s) will be repaired or replaced (at the Company's option) without charge for
parts and repair labor. After the initial 90 day period and for a period of 12 months from the date of
the original purchase, the Company will supply at no charge a replacement for any defective
part(s).
Signal System: Composite video 1.0Vp-p 75ohms
Discs Played:
1. DVD-VIDEO disc
•
•
5” (12 cm) single-sided, single-layer
5” (12 cm) single-sided, double-layer
2. Compact disc (CD-DA/CD-R/CD-RW/MP3)
3. 5” (12 cm) VIDEO CD
To obtain repair or replacement within the terms of this warranty, the end user should contact the
O.E.M. The product is to be delivered to the OEM or original place of purchase, with proof of
warranty coverage (e.g. dated bill of sale, and serial number of the unit, and vin#), specification of
defect(s), transportation prepaid, to an approved warranty station. This warranty does not extend
to the elimination of externally generated static or noise, to the correction of antenna problems, to
costs incurred for removal or reinstallation of the product, or to damage to any tapes, cd's, dvd's,
speakers, accessories, or electrical systems. This warranty does not apply to any product or part
thereof which, in the opinion of the Company, has been damaged through alteration, improper
installation, mishandling, misuse, neglect, or accident. THE EXTENT OF THE COMPANY'S
LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE, AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY THE PURCHASER FOR THE PRODUCT.
Audio Output Level: 10kohms (2 ch 2.0 Vrms)
Audio Signal Output:
•
•
•
Frequency response: 20Hz~20kHz
S/N ratio: 80dB(JIS)
Wow and Flutter below measurable limits
Specifications subject to change without notice.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE
DURATION OF THIS WARRANTY. ANY ACTION FOR BREECH OF ANY WARRANTY
HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF 30 DAYS FROM THE DATE OF ORIGINAL PURCHASE. IN
NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREECH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED
WHATSOEVER. No person or representative is authorized to assume for the Company any
liability other that expressed herein in connection with the sale of this product.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the User’s
authority to operate the equipment.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages so the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DVDB01
ASA Electronics Corporation
© 2009 ASA Electronics Corporation
v.061709
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|