Installation/Operation Instructions
for
Shower Towers
EC30000 Ristorre™ Onda™
EC31000 Ristorre™ Ovale™
EC33000 Ristorre™ Metallo™
Ovale™
Onda™
Metallo™
Save These Instructions for Future Use.
Complete and mail-in the product registration card provided with your unit.
Write and save the model and serial number of your unit.
Installer: Leave this manual for homeowner.
Homeowner: Read this manual and keep for future reference.
Copyright © by Jacuzzi Whirlpool Bath
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Ristorre™ Ovale™ Shower Tower — Specifications
optional-Supplied
Temperature
Check Spout
DIMENSIONS
SHIPPINg WEIgHT
3"
( 76 mm) d (depth)
ꢀ7 lb
10-1/4" ( ꢀ60 mm) W
46-5/8" (1184 mm) H
(13.3 kg)
Product specifications are subject to change without
notice.
PRODUCT WEIgHT
ꢀꢀ lb
(10 kg)
minimum Working Water Pressure
ꢀ1.76 psi
(1.5 bar)
maximum Working Water Pressure
Recommended Working Water Pressure
maximum Working Water Temp.
minimum Working Water Temp.
Recommended Working Temp.
7ꢀ.5ꢀ psi
(5.0 bar)
43.51 psi
(3.0 bar)
140-158° F
41-68° F
(60 – 70° C)
(5-ꢀ0° C)
(38° C)
100° F
under water pressure at
ꢀ1.76 psi (1.5 bar)
Flow Rate of Hand Shower
1.61 uS gal/min
1.69 uS gal/min
1.66 uS gal/min
1.69 uS gal/min
(6.1 L/min)
(6.4 L/min)
(6.3 L/min)
(6.4 L/min)
Flow Rate of Wall mount
Flow Rate of Body Jet
Flow Rate of Temp Check Spout
Jacuzzi Whirlpool Bath: Shower Towers
Page 3
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Ristorre™ Onda™ Shower Tower — Specifications
optional-Supplied
Temperature
Check Spout
DIMENSIONS
SHIPPINg WEIgHT
3"
( 76 mm) d (depth)
ꢀ9 lb
13-1/ꢀ" ( 343 mm) W
51-1/4" (130ꢀ mm) L
(13.ꢀ kg)
Product specifications are subject to change without
notice.
PRODUCT WEIgHT
ꢀ5 lb
(11 kg)
minimum Working Water Pressure
ꢀ1.76 psi
(1.5 bar)
maximum Working Water Pressure
Recommended Working Water Pressure
maximum Working Water Temp.
minimum Working Water Temp.
Recommended Working Temp.
7ꢀ.5ꢀ psi
(5.0 bar)
43.51 psi
(3.0 bar)
140-158° F
41-68° F
(60 – 70° C)
(5-ꢀ0° C)
(38° C)
100° F
under water pressure at
ꢀ1.76 psi (1.5 bar)
Flow Rate of Hand Shower
1.51 uS gal/min
1.69 uS gal/min
1.71 uS gal/min
1.69 uS gal/min
(6.0 L/min)
(6.4 L/min)
(6.5 L/min)
(6.4 L/min)
Flow Rate of Wall mount
Flow Rate of Body Jet
Flow Rate of Temp Check Spout
Jacuzzi Whirlpool Bath: Shower Towers
Page 4
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Ristorre™ Metallo™ Shower Tower — Specifications
optional-Supplied
Temperature
Check Spout
DIMENSIONS
SHIPPINg WEIgHT
ꢀ-1/ꢀ" ( 63.5 mm) d (depth)
1ꢀ-3/4" ( 1905 mm) W
55-7/8" (1419 mm) L
ꢀ9 lb
(13.ꢀ kg)
Product specifications are subject to change without
notice.
PRODUCT WEIgHT
ꢀ6 lb
(1ꢀ kg)
minimum Working Water Pressure
maximum Working Water Pressure
Recommended Working Water Pressure
maximum Working Water Temp.
minimum Working Water Temp.
Recommended Working Temp.
ꢀ1.76 psi
(1.5 bar)
7ꢀ.5ꢀ psi
(5.0 bar)
43.51 psi
(3.0 bar)
140-158° F
41-68° F
(60 – 70° C)
(5-ꢀ0° C)
(38° C)
100° F
under water pressure at
ꢀ1.76 psi (1.5 bar)
Flow Rate of Hand Shower
1.58 uS gal/min
1.58 uS gal/min
1.98 uS gal/min
1.98 uS gal/min
(6.0 L/min)
(6.0 L/min)
(7.5 L/min)
(7.5 L/min)
Flow Rate of Wall mount
Flow Rate of Body Jet
Flow Rate of Temp Check Spout
Jacuzzi Whirlpool Bath: Shower Towers
Page 5
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Ristorre™ Ovale™ Shower Tower — Component Identification
8
9
4
10
7
18
11
1
5
15
17
18
ꢀ7
19
17
14
ꢀ6
ꢀ4
ꢀ5
ꢀ3
ꢀ
ꢀ0a
ꢀ0b
ꢀ0c
ꢀꢀ
13
1ꢀ
6
ꢀ1
16
13
ꢀ8
no.
name
Qty Remark
no.
name
Qty Remark
Included
1
Tempered glass Front Plate
1
6
16 S.S.Flexible Hose
1
ꢀ
3
4
5
6
7
8
9
Body Jet
17 Hand Shower Bracket
18 Plastic anchor
19 Screw(m3.5xꢀ5mm)
ꢀ0a diverter
1
5
1
1
1
1
5
1
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
1
Included
Included
Included
Wall mount Shower
Shower arm
1
1
1
1
3
3
3
3
3
1
1
1
1
Included
Included
Back Housing
gasket
Included
Included
Included
Included
Included
ꢀ0b Flow Control
ꢀ0c Thermo-Static Control
ꢀ1 Sealing Washer
ꢀꢀ Threaded Connector
ꢀ3 Brass nut
Wall mount Fixing Rod
Screw(m4.ꢀX35mm)
Rubber Washer
Included
Included
Included
Included
Included
Included
Included
Included
10 Screw Cap
11 Screw nut
ꢀ4 Spring Washer
ꢀ5 Washer Plate
ꢀ6 Silica gel Washer
ꢀ7 Ring
1ꢀ Square-shaped Temperature Check Spout
13 Tube-shaped Temperature Check Spout
14 glass Shelf With Pillar
Included
Included
Included
15 Hand Shower
ꢀ8 Washer
Parts List
The parts list table common to all Ristorre shower towers is located on Page 9. Please refer to this table for com-
ponent identification of parts list in all Ristorre shower towers.
Jacuzzi Whirlpool Bath: Shower Towers
Page 6
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Ristorre™ Onda™ Shower Tower — Component Identification
4
10
9
8
7
11
18
1
3
19 17 18
14
15
5
17
ꢀ
ꢀ0a
ꢀ0b
ꢀ0c
ꢀ3
ꢀ4
ꢀ7
ꢀ6
ꢀ5
1ꢀ
13
ꢀꢀ
ꢀ1
6
16
13
ꢀ8
no.
name
Qty Remark
no.
name
Qty Remark
Included
1
Tempered glass Front Plate
1
6
16 S.S.Flexible Hose
1
ꢀ
3
4
5
6
7
8
9
Body Jet
17 Hand Shower Bracket
18 Plastic anchor
19 Screw(m3.5xꢀ5mm)
ꢀ0a diverter
1
5
1
1
1
1
5
1
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
1
Included
Included
Included
Wall mount Shower
Shower arm
1
1
1
1
3
3
3
3
3
1
1
1
1
Included
Included
Back Housing
gasket
Included
Included
Included
Included
Included
ꢀ0b Flow Control
ꢀ0c Thermo-Static Control
ꢀ1 Sealing Washer
ꢀꢀ Threaded Connector
ꢀ3 Brass nut
Wall mount Fixing Rod
Screw(m4.ꢀX35mm)
Rubber Washer
Included
Included
Included
Included
Included
Included
Included
Included
10 Screw Cap
11 Screw nut
ꢀ4 Spring Washer
ꢀ5 Washer Plate
ꢀ6 Silica gel Washer
ꢀ7 Ring
1ꢀ Square-shaped Temperature Check Spout
13 Tube-shaped Temperature Check Spout
14 glass Shelf With Pillar
Included
Included
Included
15 Hand Shower
ꢀ8 Washer
Parts List
The parts list table common to all Ristorre shower towers is located on Page 9. Please refer to this table for com-
ponent identification of parts list in all Ristorre shower towers.
Jacuzzi Whirlpool Bath: Shower Towers
Page 7
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Ristorre™ Metallo™ Shower Tower — Component Identification
10
21 11
1
3
6
8
24
23
27 26
2
14
15
17
25
9
20a
20b
20c
19
18
12
13
7
Wall
22
21
16
13
28
no.
name
Qty Remark
1
1
Front Plate
ꢀ
3
6
7
8
Body Jet
Wall mount Shower
mirror
6
1
1
Hanger
ꢀ
Included
Screw
ꢀ
1
6
Included
Included
Included
10 Connection rod
19 Screw
Parts List
The parts list table common to all Ristorre shower towers is located on Page 9. Please refer to this table for com-
ponent identification of parts list in all Ristorre shower towers.
Jacuzzi Whirlpool Bath: Shower Towers
Page 8
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Parts List
Remark
Remark
Qty
1
Qty
name
name
ꢀ0c Thermo-Static Control
1
5
1ꢀ
Square Temp Check Spout
Tube Temp Check Spout
glass Shelf assembly
Hand Shower
ꢀ1
Sealing Washer
13
14
15
16
17
18
19
1
1
1
1
1
6
6
1
1
ꢀꢀ
ꢀ3
ꢀ4
Threaded Connector
Brass nut
1
ꢀ
ꢀ
Shower Flexible Hose
Hand Shower Bracket
Plastic anchors
Spring Washer
ꢀ5
ꢀ6
ꢀ7
ꢀ8
Washer Plate
Silica gel Washer
Ring
ꢀ
ꢀ
ꢀ
1
(m3.5Xꢀ5mm) Screws
ꢀ0a diverter
Washer
ꢀ0b Flow Control
Jacuzzi Whirlpool Bath: Shower Towers
Page 9
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements.
Each unit arrives ready for installation, completely equipped with plumbing and fittings. Remove the unit from the
carton. Retain the shipping carton until satisfactory inspection of the product has been made.
CAUTION: do not drop the shower tower. dropping the unit may damage its appearance and function.
Immediately upon receipt, inspect the unit before installing. Should inspection reveal any damage or defect in the
finish, do not install. Damage or defect to the finish claimed after the unit is installed is excluded from the warranty.
Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to
the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer
NOTE: Parts with item number listed are included.
Determine the installation height of the shower tower. The height of the top row of the body jets should be level
with the users’ shoulders. Place a mark on the wall at the top of the unit when the top jets are at the desired
position. Begin installation using the following instructions.
Figure 1
Ovale
- - - - - - - - - - - - - - - - -
Onda
Finish Wall Preparation
1. drill three holes 1/4" diameter by 1-3/8” deep in
the wall at the locations and dimensions shown
in Figure 1.
a
B
C
d
5-1/8
ꢀ-3/8
33-1/4
3-1/ꢀ
7-3/16
4-1/ꢀ
46-1/ꢀ
ꢀ-1/4
D
A
ꢀ. Insert plastic anchors (18) into each of the
holes, then mount the wall mount fixing rods (7)
to the wall using the m4.ꢀx35mm screws (8),
- - - - - - - - - - - - - - - - -
measurements in inches
see Figure ꢀ.
B
Figure 2
C
NOTE: Figure 3 is for metallo only.
3. The User can adjust the height. Drill four holes at 1/4" diameter by 1-3/8" deep.
The distance of the holes are 1-3/16" and 35-3/16" apart. Insert the anchor (18)
to the holes. Then use the screw (8) to fix the location of the hanger on the wall,
see Figure 3.
Figure 3
1-3/16"
18
8
35-3/16"
1-3/16"
7
35"
1-3/16"
Jacuzzi Whirlpool Bath: Shower Towers
Page 10
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble and Install the Shower Tower
1. attach the shower arm and prepare the glass shampoo
Figure 4
platform as follows.
a. attach the shower arm (4) to the front plate (1) with
screw nut (11), see Figure 4. Confirm the screen
washer at the water inlet fitting of the wall mount
shower head (3) is in place and screw the shower
head onto the shower arm by hand. Finally, place
a sealing washer (ꢀ1) into the end connector of the
flexible tubing as shown in the Figure, and fasten
the tubing connector to the shower arm.
4
11
ꢀ1
3
b. Prepare the glass shampoo platform (14) for as-
sembly to the front plate (1), see Figure 5. Insert
the rings (ꢀ7) and rubber washer (ꢀ4) into the
threaded end of the pillar of the glass shampoo
platform (14).
1
c. attach the glass shampoo platform (14) onto the front plate using the washer plates (ꢀ5), spring washers
(ꢀ4), and brass nuts (ꢀ3) to fasten the assembly.
d. Place a sealing washer (21) into the hexagon nut of the S.S. flexible hose (16), then, attach the hose onto
the threaded connector (ꢀꢀ) at the bottom of the back housing (5), see Figure 6.
NOTE: There are five sealing washers (21). One is for use in the hexagon nut of the S.S. flexible hose, another is
used for the hand shower. The remaining three sealing washers are spare parts to be stored for later use.
NOTE: Flush the water lines supply lines to eliminate any construction debris prior to connecting water lines. ensure
there is no particle contamination on the threaded ends of the water supply pipe. debris and particles in the water
supply will reduce shower performance.
Parts List
The parts list table common to all Ristorre shower towers is located on Page 9. Please refer to this table for com-
ponent identification of parts list in all Ristorre shower towers.
Figure 5
ꢀ6
Mirror Installation
ꢀ7
14
ꢀ5
ꢀ3
8
Cover
6
9
ꢀ4
Figure 6
ꢀ1
5
ꢀꢀ
16
ꢀꢀ
Jacuzzi Whirlpool Bath: Shower Towers
Page 11
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ. Connect 1/ꢀ" hoses from the front plate (1) marked in red and blue to
the hot and cold water supply’s, respectively, as shown in Figure 7.
COLD WATER
SUPPLY
NOTE: do not bend or kink the hoses
Figure 7
when installing. Tighten fittings with a
BLUE HOSE
RED HOSE
wrench and test for leaks.
3. align the three mounting holes of the back
housing (5) and front plate (1) with the three
mounting rods (7) on wall. Fasten the front
plate to the fixing rods and attach with the
washers (9) and cap screws (10) provided.
HOT WATER
SUPPLY
(1/ꢀ" nPT
Thread)
RED AND BLUE WATER SUPPLY LINES
NOTE: Figure 8 shows the hot and cold supply
locations.
5
7
10
5
7
9
9
10
7
Ovale
Onda
Metallo
Figure 8
Place supply
lines
within hatched
region
Place supply lines
within hatched region
Place supply lines
within hatched region
6.ꢀ5"
ꢀ.00"
6.ꢀ5"
ꢀ.00"
3.50"
6.ꢀ5"
11.00"
18.50"
Jacuzzi Whirlpool Bath: Shower Towers
Page 1ꢀ
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
4. using the dimensions indicated in Figure 9, drill two holes 1/4” diameter by 1-3/8” deep into the wall on the
right hand side of the shower tower. Insert the plastic anchors (18) into each of the holes, and mount the
bracket (17) onto the wall using the m3.5xꢀ5mm Screws (19).
Figure 9
9-7/8"
(250 mm)
17
19
18
2"
(23 mm)
2 HOLES
1/4" DIA. (6,4 mm) x
1-3/8 " (35 mm)
DEEP
63"
(1600 mm)
2 HOLES
1/4" DIA. (6,4 mm) x
1-3/8 " (35 mm)
DEEP
TO FLOOR
5. Confirm the sealing washer (21) is inside the end of the S.S. flexible hose (16). Attach the hand shower (15) onto
the hose by hand and place the hand shower into the bracket as shown in Figure 10.
6. After finishing the installation, the shower tower is ready for use.
7. There is an optional tube-shaped temperature check spout (13) as an alternative to the pre-installed square-
shaped temperature check spout (1ꢀ). To exchange these two components, use a hand wrench (not sup-
plied) to remove the supply hose connecting nut attached to the square-shaped temperature check spout.
Remove the mounting nut of the spout to release it. after that, install the tube-shaped temperature check
spout into the mounting hole and tighten it, and mount it with the supplying hose, see Figure 11.
NOTE: To avoid scratching the front surface, do not turn square spout. Hold and remove washer rather than remove
the square spout.
Figure 11
1ꢀ
15
Figure 10
13
21
16
Jacuzzi Whirlpool Bath: Shower Towers
Page 13
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
1. CONTROL VALVE. The Control valve consists of three parts, the diverter (ꢀ0a),
flow control (20b), and thermo-static control (20c).
a. Diverter
20a
20b
20c
The diverter (ꢀ0a) works as a function selection. Four icons on the diverter
indicate the function selected. The four icons represent the following four
functions: Hand shower spray
Bath spout
b. Flow Control
, Body jets
, Wall mount spray
, and
.
The Flow Control (4b) is located in the center of the Control valve and is used to
control the water flow volume. Increase the water flow by turning the handle to the
left and decrease by turning to the right.
38
c. Thermo-Static Control
The thermo-Static Control (ꢀ0c) is used for setting the water temperature. There are
the“H”and“C”letters,andredandbluecolorsrepresentingHotandCold,respectively.
Users can adjust the water temperature as they want by turning the control handle.
CAUTION: The “38° C” (100° F) mark on the control represents the safety temperature level. If a higher
water temperature is needed, turn the handle left while pressing the red button.
CAUTION: Remember to return the handle to the “38°C” after use at the higher water temperature.
ꢀ. BRACKET. use the wall mounted bracket (16) to hold the hand shower (15) on wall. Select "??" on the diverter
to activate the hand shower.
Troubleshooting
1. If the water flow rate is reduced or if there is no water flow while using a specific function, dismount the shower
tower and verify the main water supply hoses (blue and red supply lines) or tubing are not bent or kinked.
ꢀ. during operation, if only cold or hot water is supplied but no combination, please check to see if the thermo-static
control (ꢀ0c) is set at the middle level. also check for bending or kinking in the main cold or hot water supply
lines.
Cleaning
do not use sand paper, thinner or other corrosive cleaner. normal non-abrasive household cleaners can be used.
Rinse with water.
Proper installation of the shower tower and compliance with local codes is the responsibility of the installer. Jacuzzi Whirlpool Bath
does not warrant connections of water supply fittings and piping, or fill systems. Nor is it responsible for damage to the shower tower
which occurs during any installation procedure.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANgE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this
type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath
145ꢀ5 monte vista avenue
Chino, California 91710
Customer Service: Call: 1-800-ꢀ88-400ꢀ
Jacuzzi Whirlpool Bath: Shower Towers
Page 14
FZ71000B • 09/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Jacuzzi Whirlpool Bath Limited Warranty
Shower System Product
WARRANTY COVERAgE
Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath
Shower System product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its
option, the unit or its equipment in accordance with the following terms and conditions.
ONE YEAR LIMITED WARRANTY ON SHOWER SYSTEM
our warranty on Shower System products is for one (1) year. our warranty covers the unit and factory-installed components (e.g., pump, motor)
against defects in material or workmanship. Warranty coverage begins on the date the unit was originally purchased by the user.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
our warranty on options and accessories manufactured by the Company is for ninety (90) days for parts only. our warranty covers options and
accessories manufactured by the Company (e.g., fill spout kits, trim kits, skirts) against defects of material or workmanship. Warranty coverage
begins on the date the option or accessory was originally purchased by the user.
WARRANTY LIMITATIONS
our warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other person, or resulting from, without
limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.); modification of any type for any reason (including
modification to meet local codes); improper installation (including installation not in accordance with instructions and specifications provided with
the unit); connections supplied by the installer of the equipment; improper voltage supply or unauthorized electrical modification; misuse; incor-
rect operation, or lack of proper routine maintenance; operation of the unit without specified minimum amount of water or at inappropriate water
temperature; use of abrasive or improper cleaners; or acts of God, such as lightning, floods, earthquakes, etc.
In addition, THe ComPany WILL noT Be ReSPonSIBLe FoR InCIdenTaL oR ConSeQuenTIaL damageS or losses arising from any
cause (e.g., water damage to carpet, ceiling, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated
parts when chemicals are used in the unit; optional equipment not manufactured by the Company, supplied by Dealer, installer or the Company;
the unit's prior usage as an operational display; or defects that should have been discovered before installation. This limited warranty does not
include: labor, transportation, or other costs incurred in the removal and/or reinstallation of the original unit and/or installation of a replacement
unit; any costs relating to obtaining access for repair; or loss of use damage, including loss of sales, profit or business advantage of any kind
under any circumstances. units in commercial use are excluded from any warranty coverage whatsoever.
Warranty coverage is provided in the united States of america only.
IMPLIED WARRANTIES
All implied warranties of merchantability and fitness for a particular purpose are equal in duration with the express warranties set forth herein.
NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties
applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company
will not be responsible for any statements or representations made in any form that go beyond, are broader than or are inconsistent with any
authorized literature or specifications furnished by the Company.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages,
so the above limitations and exclusions may not apply to you.
RETURN OF WARRANTY CARD
The attached pre-addressed Warranty Registration Card MUST be filled out by the purchaser within thirty (30) days from purchase and mailed
to Jacuzzi Whirlpool Bath in order for this warranty to become effective.
Jacuzzi Whirlpool Bath
14525 Monte Vista Avenue
Chino, California 91710
Download from Www.Somanuals.com. All Manuals Search And Download.
RESPONSIBILITIES OF OTHERS
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible
for ensuring the unit is free of defect or damage. notices are placed on and in the unit and on the shipping carton advising the installer of this
responsibility. In the event of a problem, the unit must not be installed. The Company is not responsible for failures or damage that could have
been discovered, repaired, or avoided by proper inspection and testing prior to installation.
damage occurring in transit is the responsibility of the carrier. The user or installer muST open the crates and inspect the unit for damage when it
is delivered. If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure
of the carrier to respond should be reported to the seller and the carrier. Your freight claims should be filed promptly thereafter.
It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs
relating to obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.
damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter
is the responsibility of the user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (options and accessories manufactured by the Com-
pany are warranted for ninety (90) days from the original date of purchase for parts only.)
The distributor or dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these require-
ments at the time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county,
or state building codes.
WARRANTY SERVICE
For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such
firms are not agents or representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type
covered by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department Repre-
sentative of the nature of the problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the
foregoing by the user proving that the failure occurred or was discovered within the warranty period; an authorized independent service person
or Company representative has been permitted to inspect the unit during regular business hours within a reasonable time after the problem was
reported by the user.
In order to obtain warranty service, consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath authorized Service
agent. describe the problem and the authorized Service agent will inspect the unit and provide the required warranty service.
If you are unable to contact a Jacuzzi Whirlpool Bath authorized Service agent, call or write:
Jacuzzi Whirlpool Bath
Warranty Service department
145ꢀ5 monte vista avenue
Chino, California 91710
Call: 1-800-ꢀ88-400ꢀ
To obtain warranty replacement for factory-installed components or Company supplied options and accessories manufac-
tured and supplied by the Company, call or write the above. Provide a description of the problem and proof of purchase.
you will be instructed how to obtain replacements and where to return, at your expense, the failed component(s), option(s),
or accessory(ies).
all replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced. The
Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept
the tender terminates the Company's warranty obligation.
JACUZZI WHIRLPOOL BATH
Jacuzzi® is a Federally registered trademark owned by Jacuzzi Inc. ©Copyright 1991 Jacuzzi Whirlpool Bath, FZ71000B • 9-07
Download from Www.Somanuals.com. All Manuals Search And Download.
|