Steam Enclosure
INSTALLATION INSTRUCTIONS
R
BATH
WHIRLPOOL
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important: Read complete instructions before beginning installation.
Remove the unit carefully from the carton. Retain the shipping carton until satisfactory inspection of the product has
been made. Lay out and identify all parts using the installation instructions as reference. Check the carton for small
hardware bags that tend to fall to the bottom of the carton.
Handle the glass panels carefully and protect the edges. Safety tempered glass is very resistant to breakage, but
it can be broken by banging the edges against a hard surface. Do not remove any protective devices until you are
ready to install the glass panels as the sharp corners of the panels can damage tile and floor surfaces.
Wear safety glasses whenever drilling or cutting. When drilling holes in ceramic tile or marble, use a center punch
and hammer to carefully break the surface glaze so the drill can start without skidding.
Tools required: Tape measure, Level, #2 Phillips screwdriver, flat bladed screwdriver, drill and 1/8", 7/32" drill bits
and a hacksaw.
Step 1
Measure the wall to wall opening along the center of
the bath rim. Use a hacksaw to cut the bath track 1/16"
short of this dimension. Note: On some installations it
may be necessary to file the ends of the track to match
the wall conditions.
MEASURE
Step 2
Press the four vinyl plugs into both ends of the bath
track
A
B
Step 3
Center the bath track on the bath rim and mark its
position. Note: Drain holes face the interior of the bath.
A
CENTER TRACK ON RIM
2
Download from Www.Somanuals.com. All Manuals Search And Download.
PLUMB EACH JAMB
Step 4
Position the wall jambs on each end of the bath track
withnotchesinthebottomofthejambspressedsecurely
overthebathtrack. Usealeveltoplumbeachwalljamb.
Makeapencilmarkonthewallthrougheachoftheholes
in the wall jamb. Remove all parts and drill the walls in
the locations marked using an 1/8" diameter drill. In tile
walls drill 7/32" diameter holes and insert plastic wall
plugs.
D
A
TO
Step 5
I
N
T
Apply a continuous bead of caulking on the bottom of
the bath track vinyl. Carefully replace the bath track in
the position marked in Step 3. Slide the two pieces of
jamb vinyl into the jamb filler. Replace the wall jamb
closest to the shower head. The jamb filler should be
installed with the opening closest to the interior of the
bath. (Thisinsuresmaximumwaterproofingbyposition-
ing the interior glass panel closest to the shower head.)
Attach the jamb and jamb filler to the wall with three #8
x 1-1/2" truss head screws.
E
RI
OR
OF
B
A
T
F
H
G
H
Step 6
Measure the wall to wall opening at the top of the
mounted wall jamb. Cut the header 1/16" short of this
measurement. Check the header for fit.
MEASURE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7
All units are equipped with safety tee-lock jambs.
Wheninstalledproperlytheheaderispermanentlylocked
to the jambs and cannot be accidently dislodged. Slide
the safety lock of the remaining wall jamb and jamb filler
intotheheader. Theroundedsurfaceoftheheadergoes
to the exterior and the jamb filler should be positioned
with the opening closet to the exterior of the wall jamb.
Holding the header at an angle engage the opposite
end onto the mounted wall jamb and press the wall jamb
into position on the bath track. Attach to the wall per
Step 4.
TEE-LOCK
I
D
I
D
A
J
Step 8
Obscure glass panels are installed with the rough
side of the glass to the exterior. Attach rollers to the
interior panel (rough glass surface closest to the top fin)
and the exterior (rough surface away from the top fin
using four 8-32 x 3/8" hex head screws. Press four vinyl
silencers into the slots in the fin on the bottom of both
panels.
K
J
ROUGH
SURFACE
EXTERIOR
PANEL
INTERIOR
PANEL
L
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 9
Peel protective backing from the four adhesive
bumpers and stick to top and bottom of the panel recess
in the wall jambs. Lift the interior panel into position with
the rollers engaging the roller slot in the header and the
bottom fin inserted into the interior slot of the bath track.
Repeat for the exterior panel. The vertical vinyl wiper
blade of the interior panel should seal against the
exterior panel when both panels are in a closed position.
Ifthepanelsarenotparalleltothewalljambs, remove
thedoorsandadjusttherollersupordowntocompensate.
Step 10
Press the trim ring over the base of the four acrylic
towel bar brackets and press the brackets into the ends
ofthetowelbars. Attachtheassembledtowelbarstothe
glass panels with four 10-24 x 7/8" truss head screws.
Q
N
O
P
N
Q
O
Step 11
Caulk the ends of the bath track and the interior
surface of the wall jambs
Step 12
Clean your Steam Enclosure with a soft cloth and
nonabrasive cleaner.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this
type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath
P.O. Box 702168, Dallas TX 75370-2168
Service Support: (800) 288-4002
©1996 Jacuzzi Whirlpool Bath J992000
8/13/04
Printed on Recycled Paper
Printed in the U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|