DESIGNER/LUXURY BATH SERIES
INSTALLATION / OPERATION INSTRUCTIONS
Save These Instructions for Future Use.
Complete and mail-in the product registration card provided with your unit.
Write and save the model and serial number of your unit below.
Owner's Record
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Number _____________________________________________________________
Model ____________________________________________________________________
Installer: Leave this manual for homeowner.
Homeowner: Read this manual and keep for future reference.
©2005 Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
DANGER — RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND
FAULT CIRCUIT INTERRUPTER (GFCI).
CAUTION — TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE
PERIODICALLY IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS.
WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL. DO NOT
USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURERS.
WARNING—TOAVOIDINJURY,EXERCISECAUTIONWHENENTERINGOREXITINGTHEHYDROMASSAGEBATHTUB.
WARNING — KEEP BODY AND HAIR A MINIMUM OF 6" (15,2 cm) AWAY FROM SUCTION FITTING AT ALL
TIMES WHEN THE HYDROMASSAGE SYSTEM IS OPERATING. HAIR LONGER THAN SHOULDER
LENGTH SHOULD BE SECURED CLOSE TO THE HEAD.
WARNING — RISK OF ELECTRICAL SHOCK; DO NOT PERMIT ELECTRICAL APPLIANCES (SUCH AS HAIR
DRYER, LAMP, TELEPHONE, RADIOORTELEVISION)WITHIN60"(1,5M)OFTHISHYDROMASSAGEBATHTUB.
WARNING — RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE DRUGS OR ALCOHOL
BEFORE OR DURING THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID
UNCONSCIOUSNESS AND POSSIBLE DROWNING.
WARNING — RISK OF FETAL INJURY; PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD
CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.
WARNING — RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; DO NOT USE A HYDROMASSAGE
BATHTUB EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.
WARNING — RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; WATER TEMPERATURE IN
EXCESS OF 104°F (40°C) MAY BE INJURIOUS TO YOUR HEALTH. CHECK AND ADJUST WATER
TEMPERATURE BEFORE USE.
WARNING — RISK OF HYPERTHERMIA; PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB
EQUIPPED WITH A HEATER.
FOR BUILT-IN AND DROP-IN UNITS, INSTALL TO PERMIT ACCESS FOR SERVICING.
THIS UNIT SHOULD BE ELECTRICALLY GROUNDED AND INSTALLED BY A LICENSED CONTRAC-
TOR, ELECTRICIAN, AND PLUMBER.
BUILDING MATERIALS AND WIRING SHOULD BE ROUTED AWAY FROM THE MOTOR/PUMP OR
BLOWER OR OTHER HEAT PRODUCING COMPONENTS OF THIS UNIT.
A PRESSURE WIRE CONNECTOR IS PROVIDED ON THE EXTERIOR OF THE MOTOR/PUMP AND
HEATER TO PERMIT CONNECTION OF AN NO. 8 AWG (8.4 MM) SOLID COPPER BONDING CONDUCTOR
BETWEEN THIS UNIT AND ALL OTHER ELECTRIC EQUIPMENT AND EXPOSED METAL IN THE VICINITY,
AS NEEDED TO COMPLY WITH LOCAL REQUIREMENTS.
PRECAUTIONS
•
Do not operate the hydromassage system unless the bath is filled with water to at least 1" to 2" (2,5 - 5,08 cm) above the
highest jet.
•
•
•
•
Do not immerse the control panel by overfilling the bath.
Do not use oil-based bath additives in your hydromassage bath.
When cleaning your bath, do not use abrasive substances which will damage the bath's surface.
To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).
NOTE: This is a professional grade product. Aknowledge of construction techniques, plumbing and electri-
cal installation according to codes are required for proper installation and user satisfaction. We recommend
that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does
not cover improper installation related problems.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
The Company has obtained applicable code (standards) listings generally available on a national basis for products of this type.
It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. The
Company makes no representation or warranty regarding, and will not be responsible for any code compliance.
3
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Safety Instructions _____________________________________________________________________ 2-3
Contents _____________________________________________________________________________ 4
Specifications _________________________________________________________________________ 5-8
Roughing-in Reference _________________________________________________________________ 9-13
Installations Instructions _________________________________________________________________ 14-19
Framing and Support _________________________________________________________________ 14
Service Access ______________________________________________________________________ 15
ALLUSION Installation ________________________________________________________________ 16-17
Electrical Connections _________________________________________________________________ 18
Plumbing and Water Supply ____________________________________________________________ 19
Clean Up After Installation _______________________________________________________________ 19
Operating Instructions __________________________________________________________________ 20-22
Maintenance Instructions ________________________________________________________________ 23-24
General Troubleshooting Guide ___________________________________________________________ 25
Authorized Service _____________________________________________________________________ 26
Warranty _____________________________________________________________________________ 27-28
NOTE: If you need a referral for a service company near you, or need assistance with operation or maintenance
related questions, please call our Service Support Department at 1-800-288-4002. Visit our web site at http://
www.jacuzzi.com/ for products and services.
To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
4
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly, heater, plumb-
ing, and fittings necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the
bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been
made. Do not lift the bath by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the
finish, do not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the
warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good
order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations,
refer to the published warranty information packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. NOTE: Prior to
installation, the bath must be filled with water and operated to check for leaks that may have resulted from
shipping damage or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been
discovered, repaired, or avoided by following this inspection and testing procedure.
MAX 1"
A
L
W
(Heater)
(51 mm)
H
2"
4"
B
(102 mm)
DRAIN/OVERFLOW
(Motor)
SIDE VIEW
END VIEW
W
ALLUSION
MAX. 1/2"
MAX. 1/2"
L
L
W
2"
(Heater)
H
H
(Heater)
2"
(51 mm)
(51 mm)
(Motor)
(Motor)
SIDE VIEW
END VIEW
SIDE VIEW
END VIEW
CIPREA™, Right Hand
BELLAVISTA
MAX. 1/2"
H
MAX. 1/2"
H
L
W
L
W
1/2"
2"
(Heater)
(Heater)
(13 mm)
(51 mm)
(Motor)
(Motor)
SIDE VIEW
END VIEW
SIDE VIEW
END VIEW
ELARA
REÁL™, Right Hand
MAX. 1/2"
L
MAX. 1/2"
2" (51 mm)
W
L
W
(Heater)
H1
H2
H3
1"
2"
(Heater)
H
(25 mm)
(51 mm)
(Motor)
(Motor)
SIDE VIEW
END VIEW
END VIEW
SIDE VIEW
TORRETTA 36
SABELLA
5
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand
HEATER,
INTAKE/DISCHARGE
SKIRT &
MOUNTING
TOTAL WEIGHT/
CUTOUT FLOOR LOADING GALLONAGE
OPERATING
PRODUCT
WEIGHT
DRAIN/OVERFLOW
DIMENSIONS
MODEL
135 lb
(61 kg)
ALLUSION™
6636
66"
36"
26"
(1676 mm) L 17-3/8" (441 mm) A
( 914 mm) W 11-15/16" (210 mm) B
( 660 mm) H
Template
Provided
P/N
843 lb
(383 kg)/
51 lb/ft2
Min - 55 U.S. gal
(208 liters)
Max - 75 U.S. gal
(284 liters)
Not Available
Factory Installed
Intake
(S749000 Heater)
RH
BY20000
(248 kg/m2)
145 lb
(66 kg)
ALLUSION™
7236
72"
36"
26"
(1829 mm) L 17-3/8" (441 mm) A
( 914 mm) W 11-15/16" (210 mm) B
( 660 mm) H
Template
Provided
P/N
978 lb
(489 kg)/
54 lb/ft2
Min - 65 U.S. gal
(246 liters)
Max-85 U.S. gal
(322 liters)
Not Available
Not Available
Factory Installed
Intake
(S749000 Heater)
RH
BY20000
(263 kg/m2)
169 lb
(77 kg)
ALLUSION™
7242
72"
42"
26"
(1829 mm) L 17-3/8" (441 mm) A Template
(1067 mm) W 11-15/16" (210 mm) B
( 660 mm) H
1127 lb
(470 kg)/
54 lb/ft2
(263 kg/m2)
Min - 75 U.S. gal
(284 liters)
Max - 99 U.S. gal
(375 liters)
Factory Installed
Intake
(S749000 Heater)
Provided
P/N
BY20000
RH
110 lb
(50 kg)
BELLAVISTA™
5
60"
42"
26"
(1524 mm) L 20"
(1067 mm) W 11-3/4" (298 mm) B
( 660 mm) H
(508 mm) A
Template
Provided
P/N
1026 lb
(466 kg)/
59 lb/ft2
80 U.S. gal
(303 liters)
Not Available
Not Available
Factory Installed
Intake
(S749000 Heater)
RH
P187000
(288 kg/m2)
120 lb
(56 kg)
BELLAVISTA™
5.5
66"
42"
26"
(1676 mm) L 20"
(1067 mm) W 11-3/4" (298 mm) B
( 660 mm) H
(508 mm) A
Template
Provided
P/N
1078 lb
(490 kg)/
56 lb/ft2
(273 kg/m2)
85 U.S. gal
(322 liters)
Factory Installed
Intake
(S749000 Heater)
RH
P187000
130 lb
(59 kg)
BELLAVISTA™
6
72"
42"
26"
(1829 mm) L 20"
(1067 mm) W 11-3/4" (298 mm) B
( 660 mm) H
(508 mm) A
Template
Provided
P/N
1130 lb
(514 kg)/
54 lb/ft2
90 U.S. gal
(341 liters)
Not Available
Included
Factory Installed
Intake
(S749000 Heater)
RH
P187000
(263 kg/m2)
170 lb
(77 kg)
72"
48"
(1829 mm) L† 16-1/4" (413 mm) A
(1219 mm) W 13-1/2" (343 mm) B
NA
895 lb
(407 kg)/
37 lb/ft2
(180 kg/m2)
57 U.S. gal
(216 liters)
Factory Installed
Intake
(S749000 Heater)
CIPREA™
RH
20-1/2" ( 521 mm) H
58" x 40"
(1473 mm x
1016 mm)
Umt Template
Provided
200 lb
(91 kg)
ELARA™ 6042
LH & RH
60”
42”
(1524 mm) L 18.5” (470 mm) A
(1067 mm) W 10.6” (269 mm) B
1126 lb
(512 kg)/
Min - 83 U.S. gal
(314 liters)
Max - 92 U.S. gal
(348 liters)
Not Available
Factory Installed
Intake
(S749000 Heater)
23-1/2” (597 mm) H
65.4 lb/ft2
(319 kg/m2)
P/N DQ50000
64" x 34"
(1626 mm x
864 mm)
Umt Template
Provided
200 lb
(91 kg)
ELARA™ 6636
LH & RH
66”
36”
(1676 mm) L 18.5” (470 mm) A
( 914 mm) W 10.6” (269 mm) B
1039 lb
(472 kg)/
63 lb/ft2
Min - 75 U.S. gal
(284 liters)
Max - 83 U.S. gal
(314 liters)
Not Available
Not Available
Factory Installed
Intake
(S749000 Heater)
23-1/2” (597 mm) H
(307 kg/m2)
P/N DQ51000
70" x 40"
(1778 mm x
1016 mm)
Umt Template
Provided
215 lb
(98 kg)
ELARA™ 7242
LH & RH
72"
42"
(1829 mm) L 18.5” (470 mm) A
(1067 mm) W 10.6” (269 mm) B
1345 lb
(611 kg)/
64 lb/ft2
Min - 95 U.S. gal
(360 liters)
Max-105 U.S. gal
(398 liters)
Factory Installed
Intake
(S749000 Heater)
23-1/2" ( 597 mm) H
(312 kg/m2)
P/N BZ51000
130 lb
(59 kg)
REÁL™
RH
72"
42"
23"
(1829 mm) L† 20" (508 mm) A
70" x 40"
(1778 mm x
1016 mm)
1130 lb
(514 kg)/
54 lb/ft2
90 U.S. gal
(341 liters)
Not Available
Not Available
Not Available
Factory Installed
Intake
(S749000 Heater)
(1067 mm) W 14"
( 584 mm) H
(356 mm) B
(263 kg/m2)
133 lb
(60 kg)
SABELLA™
RH
72"
47"
(1829 mm) L 20" (508 mm) A
(1194 mm) W 14" (356 mm) B
Template
Provided
P/N
1199 lb
(545 kg)/
51 lb/ft2
98 U.S. gal
(371 liters)
Factory Installed
Intake
(S749000 Heater)
23-3/4" ( 584 mm) H
P187000
(249 kg/m2)
115 lb
(52 kg)
TORRETTA™ 36 72"
35-1/8" ( 892 mm) W 15"
22-7/8" ( 581 mm) H1
21" ( 533 mm) H2
23-1/2" ( 597 mm) H3
(1829 mm) L 18-3/16" (459 mm) A
Template
Provided
P/N
948 lb
(431 kg)/
54 lb/ft2
70 U.S. gal
(265 liters)
Factory Installed
Intake
(S749000 Heater)
(381 mm) B
P652000
(263 kg/m2)
† Add 1/4" to this dimension when roughing-in for 3-wall niche.
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
RapidHeatTM: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 120 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
6
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
OVAL & ROUND BATHS
A
MAX. 2-1/2"
H
L
W
1/2"
B
(Heater)
(13 mm)
DRAIN/OVERFLOW
(Motor)
SIDE VIEW
END VIEW
DUETTA™
(51 mm)
2"
L
(Heater)
MAX. 1/2"
H
L
W
W
(Heater)
(Motor)
(Motor)
SIDE VIEW
END VIEW
CORTINA™
VENICIA™
SPECIFICATIONS (Oval & Round) LH = Left Hand, RH = Right Hand
PRODUCT
WEIGHT
SKIRT &
MOUNTING
HEATER,
INTAKE/DISCHARGE
TOTAL WEIGHT/
CUTOUT FLOOR LOADING
DRAIN/OVERFLOW
DIMENSIONS
OPERATING
GALLONAGE
MODEL
DIMENSIONS
CORTINA™
72"
72"
(1829 mm) L
(1829 mm) W 19-1/4" (489 mm) B (1778 mm)
16-3/4" (426 mm) A
70" Dia.
1293 lb
(588 kg)/
36 lb/ft2
(176 kg/m2 )
100 U.S. gal
(379 liters)
210 lb
(95 kg)
Not Available
Factory Installed
Discharge
(U394000 HEATER)
RH
22-1/4" ( 565 mm) H
Hole
DUETTA™
6042
60” (1524 mm) L
42” (1067 mm) W
26” ( 660 mm) H
18.4" (467 mm) A Template
999 lb
Min - 77 U.S. gal
(291 liters)
Max - 83 U.S. gal
(314 liters)
110 lb
(50 kg)
Not Available
Factory Installed
Intake
(S749000 Heater)
11"
(279 mm) B
Provided
P/N
(454 kg)/
57.1 lb/ft2
RH
DA09000
(278 kg/m2
)
DUETTA™
6636
66” (1676 mm) L
36” (914 mm) W
26” ( 660 mm) H
18.4" (467 mm) A Template
1019 lb
(463 kg)/
61.8 lb/ft2
(301 kg/m2
Min - 75 U.S. gal
(284 liters)
Max - 80 U.S. gal
(303 liters)
180 lb
(82 kg)
Not Available
Not Available
Not Available
Not Available
Factory Installed
Intake
(S749000 Heater)
11"
(279 mm) B
Provided
P/N
RH
DA08000
)
)
DUETTA™
6642
66” (1676 mm) L
42” (1067 mm) W
18.4" (467 mm) A Template
1106 lb
(503 kg)/
57.5 lb/ft2
(280 kg/m2
Min - 90 U.S. gal
(341 liters)
Max - 95 U.S. gal
(360 liters)
117 lb
(53 kg)
Factory Installed
Intake
(S749000 Heater)
11"
(279 mm) B
Provided
P/N
26”
(660 mm) H
RH
DA07000
DUETTA™
7242
72" (1829 mm) L
42" (1067 mm) W
26" ( 660 mm) H
18.4" (467 mm) A Template
1277 lb
(581 kg)/
60.8 lb/ft2
(296 kg/m2 )
Min - 98 U.S. gal
(371 liters)
Max - 106 U.S. gal
(401 liters)
130 lb
(59 kg)
Factory Installed
Intake
(S749000 Heater)
11"
(279 mm) B
Provided
P/N
RH
DA06000
VENICIA™
72" (1829 mm) L
42" (1067 mm) W
23" ( 584 mm) H
20"
14"
(508 mm) A
(356 mm) B
Template
Provided
P/N
1130 lb
(514 kg)/
54 lb/ft2
(263 kg/m2 )
90 U.S. gal
(341 liters)
130 lb
(59 kg)
Factory Installed
Intake
(S749000 Heater)
RH
P187000
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4
mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
RapidHeatTM: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 120 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
7
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
CORNER BATHS
MAX. 1/2"
W
2"
A
(51 mm)
H
(Heater)
B
END VIEW
SIDE VIEW
DRAIN/OVERFLOW
BELLAVISTA™ CORNER, Right Hand
SPECIFICATIONS (Corner) LH = Left Hand, RH = Right Hand
TOTAL WEIGHT/ OPERATING PRODUCT
CUTOUT FLOOR LOADING GALLONAGE WEIGHT
SKIRT &
MOUNTING
DRAIN/OVERFLOW
DIMENSIONS
HEATER,
INTAKE/DISCHARGE
MODEL
DIMENSIONS
BELLAVISTATM 60"
(1524 mm) L 18-7/8" (479 mm) A Template
Not Available
Factory Installed
Intake
(S749000 Heater)
1046 lb
(475 kg)/
42 lb/ft2
130 lb
(59 kg)
80 U.S. gal
(303 liters)
CORNER
60"
(1524 mm) W 14"
(356 mm) B Provided
21-3/4" ( 553 mm) H
P/N
P654000
(205) kg/m2
RH
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
mm).
RapidHeatTM: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 120 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
8
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN REFERENCE
ROUGHING-IN REFERENCE (RECTANGULAR)
Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers.
66"
72"
Motor
Motor
5" x 5"
5" x 5"
8-1/2"
36"
8-1/2"
36"
42"
42"
Heater
Heater
11-15/16"
11-15/16"
Opt. Service
Access
Opt. Service
Access
33"
36"
ALLUSION™ 6636, Right Hand
ALLUSION™ 7236, Right Hand
72"
12" H x 18" L
Service Access
60"
Motor
5" x 5"
8-1/2"
Motor
4" x 4"
30-1/8"
42"
Heater
Heater
11-15/16"
11-3/4"
6"
Opt. Service
Access
36"
7"
32-1/2"
ALLUSION™ 7242, Right Hand
Opt. Service Access
BELLAVISTA™ 5, Right Hand
12" H x 18" L
Service Access
66"
12" H x 18" L
Service Access
72"
Motor
30-1/8"
4" x 4"
42"
30-1/8"
11-3/4"
Motor
Heater
4" x 4"
Heater
11-3/4"
6"
6"
10"
35-1/2"
Opt. Service Access
Opt. Service
Access
10-1/2"
BELLAVISTA™ 6, Right Hand
35-13/16"
BELLAVISTA™ 5.5, Right Hand
12" H x 18" L
Service Access
*72"
36"
48"
Motor
34-1/2"
7"
14" x 4"
Heater
4"
CIPREA™, Right Hand
* Add 1/4" to this dimension when roughing-in for 3-wall niche.
NOTE: 1. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
2. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
3. Service access dimensions given are minimum size.
4. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
9
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN REFERENCE
ROUGHING-IN REFERENCE (RECTANGULAR)
Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers.
60"
60"
21"
21"
12" x 4"
2"
12" x 4"
2"
Motor
Motor
Heater
42"
42"
Heater
4.2"
4.2"
Opt. Service
Access
Opt. Service
Access
12" H x 18" L
Service Access
12" H x 18" L
Service Access
10.6"
10.6"
ELARA™ 6042 Left Hand
ELARA™ 6042 Right Hand
66"
66"
18 "
18 "
4.2"
12" x 4"
Motor
12" x 4"
Motor
36"
36"
Heater
2"
Heater
2"
4.2"
Opt. Service
Access
12" H x 18" L
Service Access
Opt. Service
Access
12" H x 18" L
Service Access
10.6"
10.6"
ELARA™ 6636 Right Hand
ELARA™ 6636 Right Hand
Opt. Service
Access
10.6"
12" H x 18" L
Opt. Service
Access
10.6"
Service Access
4.2"
21"
Heater
Motor
12" x 4"
4.2"
21"
Heater
12" x 4"
42"
42"
2"
2"
Motor
12" H x 18" L
Service Access
72"
72"
ELARA™ 7242 Right Hand
ELARA™ 7242 Left Hand
* Add 1/4" to this dimension when roughing-in for 3-wall niche.
NOTE: 1. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
2. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
3. Service access dimensions given are minimum size.
4. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
10
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN REFERENCE
ROUGHING-IN REFERENCE (RECTANGULAR)
Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers.
1"
1"
72"
72"
Motor
3"
42"
Motor
Heater
18" x 4"
18" x 4"*
47"
3"
3"
3"
7"
Opt. Service
Access
10-1/2"
5-1/4"
36"
Heater
10-1/4"
36"
Opt. Service
Access
REÁL™, Right Hand
SABELLA™ Right Hand
72"
Motor
15" X 4"
18"
36"
Heater
6-3/4"
Opt. Service Access
15-1/4"
TORRETTA™ 36, Left Hand
* Add 1/4" to this dimension when roughing-in for 3-wall niche.
NOTE: 1. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
2. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
3. Service access dimensions given are minimum size.
4. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
11
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN REFERENCE
ROUGHING-IN REFERENCE (OVAL)
Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers.
66"
60"
Motor
Motor
13" x 4"
13" x 4"
2"
36"
2"
42"
Heater
Heater
Opt. Service
Access
3.84"
33"
Opt. Service Access
3.84"
30"
11.04"
11.04"
DUETTA™ 6042, Right Hand
DUETTA™ 6636, Right Hand
66"
12" H x 18" L
Service Access
72"
Motor
42"
14" x 4"
Motor
13" x 4"
2"
Heater
42"
Heater
3-1/2"
11"
Opt. Service
Access
3.84"
33"
Opt. Service
Access
2"
11.04"
36"
DUETTA™ 7242, Right Hand
DUETTA™ 6642, Right Hand
12" H x 18" L
Service Access
72"
Motor
18" x 4"
29-7/8"
5-1/4"
42"
Heater
3"
Opt. Service Access
10-1/2"
VENICIA™, Right Hand
36"
NOTE: 1. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
2. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
3. Service access dimensions given are minimum size.
4. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
12
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUGHING-IN REFERENCE
ROUGHING-IN REFERENCE (ROUND, CORNER)
Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers.
60"
Service
Access
14"x5"*
60"
59-1/2"
Ref.
72"
5"
Heater
34-9/16"
16"
26"
Motor
12"x4"
3"
Heater
Opt.
Service
Access
16"
12" H x 18" L
Service Access
Motor
4"
7-1/2"
9"
77-3/4"
BELLAVISTA™ CORNER, Right Hand
72"
CORTINA™, Right Hand
NOTE: 1. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
2. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
3. Service access dimensions given are minimum size.
4. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
13
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Framing and Support
The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor.
The floor structure beneath the bath must be able to support a total weight of bath, water, and bather.
Refer to the table under total weight for your model. The unit must be supported from the bottom of the bath and
not from the bath rim or tile flange. If the subfloor is level and a continuous surface, no other preparation is neces-
sary. You can proceed to install the bath. If the subfloor is not level, you MUST level the entire surface prior to
installing the bath. The use of materials that provide a level installation are allowed provided the method used will
insure a level bath that is supported from the bottom. Materials that may be used are a floor leveling compound,
mortar, plaster or minimal expansion structural foam having a density of a minimum of 5 lbs./cubic feet; however the
bath must remain level in order for it to drain properly and all foam feet must make full contact with the leveling
material. Both sides of a joint or splice of subfloor should be level to each other. When attaching baths with
flanges to stud wall, use shims to fill any gaps between the bath flange and studs.
NOTE: Drop-in tubs are additionally equipped with metal anchor straps. With a level floor, when mortar or
similar anchoring material is NOT used, use construction adhesive under the foam feet and fasten the metal
anchor straps to the floor to prevent the unit from shifting while trim, deck finishes, or finish caulking cure.
The rim of the bath is not designed to support weight. If finish material is to overlap or contact the bath, the added
weight must be fully self-supporting.
The protective film liner inside the bath is used to prevent damage to the finish during installation. Before
installation, remove liner to inspect for any defects, reapply and do not remove until final cleanup.
Important: If a skirt is to be used, it must be installed at the time of unit installation – refer to skirt instal-
lation instructions. Install optional trim parts when all installation has been completed.
TYPICAL INSTALLATIONS
MORTAR OR ADHESIVE
SEALANT
TILE
FINISHING
MATERIAL
MORTAR OR ADHESIVE
TILE
MORTAR
PLASTER
FILLER
SEALANT
CEMENT
BOARD
BATH RIM
FLASHING
FLANGE
NAIL
SUB-FLOOR
FLASHING
OR
SILICONE
SEALANT
SCREW
STUD
WALL
1" X 4" (NOT FOR
SUPPORT)
1" X 4" (NOT FOR SUPPORT)
1" X 4" (NOT FOR SUPPORT)
FLUSH TO WALL
OPTIONAL TILE FLANGE KIT
SEMI-SUNKEN
TYPICAL FLANGE MOUNTING DETAIL
TILE
TILE
STUD
STUD
CAULKING
CEMENT
BOARD
CEMENT
BOARD
CAULKING
TILE
ADHESIVE
TILE
ADHESIVE
FLANGE
FLANGE
ATTACH WITH
SCREWS
PROVIDED
ATTACH WITH
SCREWS
PROVIDED
SHIM IF
SHIM IF
NECESSARY
TO FILL GAPS
NECESSARY
STUD
STUD
TO FILL GAPS
BETWEEN
STUD
BETWEEN
STUD
AND FLANGE
1/8" GAP
1/8" GAP
FLANGE
AND FLANGE
1"X 4"
(NOT FOR
SUPPORT)
FLANGE
14
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
The Duetta Whirlpool baths should access as shown
below.
DUETTA SERVICE ACCESS (WITHOUT SKIRT)
Service Access
For partially or fully sunken installations, allow for ac-
cess to service connections. It is the installer's respon-
sibility to provide sufficient service access. The recom-
mended minimum dimensions allowable for service to
the bath are shown in the "Service Access" illustration.
Provide adequate area around unit for air circulation
for cooling the motor and to supply sufficient air to the
jets. Do not insulate this area or around motor.
HEATER
12"
SERVICE ACCESS (WITHOUT SKIRT)
FRONT
18"
12"
PREFERRED
ACCESS
ALTERNATE
ACCESS
MOTOR
18"
12"
18"
TheAllusion Whirlpool baths should access as shown
below.
ALLUSION SERVICE ACCESS
12"
ALTERNATE
ACCESS
PUMP/MOTOR
PREFERRED
ACCESS
MOTOR
18"
HEATER
12"
FRONT
18"
12"
PREFERRED
ACCESS
18"
ALTERNATE
ACCESS
Service Access (Corner Tubs)
In some cases, access may not have been provided
because of the design of the bath environment and hav-
ing full understanding that in this case, it may be neces-
sary to remove the unit for service.
If this is the case, diagnosing a problem may not be
possible without complete access to the plumbing sys-
tem. This would necessitate the removal of the unit.
Although this practice is not commonly implemented, it
is an acceptable method.
For partially or fully sunken installations, allow for ac-
cess to service connections. It is the installer's respon-
sibility to provide sufficient service access. The recom-
mended minimum dimensions allowable for service to
the bath are shown in the "Service Access" illustration.
Provide adequate area around unit for air circulation
for cooling the motor and to supply sufficient air to the
jets. Do not insulate this area or around motor.
SERVICE ACCESS
SERVICE ACCESS (CORNER BATHS)
AREA
A
20"
AREA
B
A
18"
MOTOR
C
B
In some cases access may have been provided in
Area A but service is required in Area B which requires
the unit to be pulled for service and reinstalled.
If service access has not been provided, it is the
home owners responsibility to remove the bath and
providetherequiredaccess,shouldarepairbecome
necessary.
36"
24"
RIGHT HAND UNIT SHOWN
A- Preferred access
B - Acceptable alternative if access A is not possible
C - Additional access for equipment (Optional)
15
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
INSTALLATION CLEARANCE RECOMMENDATIONS
The installation clearance recommendations below are to ensure that installers have enough space to maneuver and
insert tub. The Designer/Luxury line whirlpool tubs have electrical, plumbing and lighting systems installed. Do not
lift the bath by the plumbing or wiring at any time; handle by the shell only.
TWO WALL INSTALLATION
TUB
CUTOUT
TUB
CUTOUT
10"
32"
THREE WALL INSTALLATION
MINIMUM VERTICAL CLEARANCE
FOR INSTALLER TO POSITION TUB
TUB
CUTOUT
TUB
CUTOUT
32"
32"
3"
10"
16
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Installation
See END/SIDE VIEW in
Specification pages for
this dimension.
Note that the motor/pump protrudes beyond the bath rim a maxi-
mum distance of 1" (25,4 mm). Care should be used when lowering
the tub into cutout to prevent injury to installer(s), finished surfaces,
or tub and components.
(Heater)
(Motor)
Clearance must be provided for installers. See page 16 for
recommended clearances surrounding tub. Damage to shell,
plumbing, wiring, lighting, and other components because of
failure to observe minimum clearances are not the responsibility
of Jacuzzi Whirlpool Bath.
All deck finish work must be completed before installation. Use the Cutout Template provided. Flooring surface inside
the cutout to deck height must not exceed height specification for tub.
Cover all finished surfaces to protect from damage during tub installation.
Turn OFF power supply to dedicated GFCI protected circuits.
Begin Installation
Optionally, use a washable marker to scribe a reference line 1" (25,4 mm) out-
side the cutout edge on the deck surface. This may assist in final alignment of the
tub.
TUB
CUTOUT
Install any trim kits, faucets, or other tub components before installing.
REFERENCE
LINE
1/2"
To install unit insert the motor/pump end first when lowering the tub into the
cutout opening as shown in the bottom illustration. Do not use plumbing fixtures or
plumbing lines to lower unit. The clearance under the substrate is required for air
flow circulation requirements.
Place a piece of scrap lumber under each corner as a temporary support for the tub rim. Inspect all fittings, plumbing, and
control lines after inserting to insure components are not damaged, disconnected, or contacting the finish surface substrate or
support members.
FINISHED SURFACE
Connect flex water supply lines to faucet.
SCRAP LUMBER
2 " MAX
THICKNESS
Plug power cords into GFCI outlet.
Remove fingers, hands, and all other items from under the rim edge before lowering the tub.
Slightly lift one tub end and remove the scrap lumber. Gently lower the tub rim until it contacts the
APPROX. 2-1/2"
deck surface. Slightly lift the remaining tub end and remove the scrap lumber. Gently lower the
SUBSTRATE
tub rim until it contacts the deck surface.
If you created the optional reference lines, align the tub over the cutout.
Connect drain line.
SUBFLOOR
SUPPORT
Turn ON the power supply to the dedicated GFCI protected circuits.
Check for leaks and check system operation.
** MIN CLEARANCE - DUETTA 3"-3½"
TILE OR FINISHED
SURFACE
SUBSTRATE
TILE OR
FINISHED
SURFACE
TYP MIN. 1-1/2"
CLEARANCE**
SUBSTRATE
SUPPORT
MEMBER
SUBFLOOR
SUPPORT
MEMBER
17
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Electrical Connections
Separate circuits, each must be protected by a Ground Fault Circuit Interrupter (GFCI), are required for the pump/
motor and the RapidHeatTM Heater. Refer to the electrical specification for each model on pages 6-8. Install duplex
outlets to the studwall underneath the bathtub, at least 4 inches (10,2 cm) above the floor or in accordance with local
building or electrical codes. Duplex outlets are not provided. Because these units are manufactured with an elec-
tronic control panel no remote switch or timer is necessary.
Tubs with electronic control panels combine the electrical requirements of the pump/motor and electronic controls
into a control box. For these units the power supply cord from the pump/motor runs to the control box. The power
supply cord from the control box should be connected to the 20 AMP GFCI circuit.
Before installing electrical connections, inspect the pump/motor and heater nameplates and confirm you have 120
VAC, 20 AMP and 15 AMP service requirements. The GFCI circuits must match these requirements. Care must be
taken to connect the 20 AMP pump/motor or control box power cord ONLY to the 20 AMP GFCI circuit and to connect
the 15 AMP heater power cord ONLY to the 15 AMP GFCI circuit. Do NOT switch power cords and GFCI circuits.
With a #8 solid copper wire, bond the heater to the house electrical panel or approved local bond. Abonding lug is
provided on the heater. With another #8 solid copper wire, bond the pump/motor to the house electrical panel or
approved local bond. A bonding lug is provided on the pump/motor.
At initial start-up and before each use thereafter with power ON, push the GFCI test button on each circuit. The
reset button should pop out. Push this button in to reset. If the interrupter fails to operate in this manner, there is a
ground current flowing or a device malfunction, indicating the possibility of electrical shock. Turn off power and do
not use the bath until the source of the problem has been identified and corrected.
DANGER: RISK OF ELECTRIC SHOCK. Connect only to a circuit protected by a Ground Fault Circuit Inter-
rupter (GFCI).
CAUTION: Operating the motor/pump without enough water in the bath can cause leaking and permanent
damage to the pump. Before power is applied to the installation, make sure the switch is in the OFF position
to avoid pump damage.
ELECTRICAL CONNECTION
15 AMP, 3 PRONG PLUG
(Heater)
20 AMP, 3 PRONG PLUG
(Pump/Motor)
DUPLEX
RECEPT.*
4" MIN.
OR IN
ACCORDANCE
WITH LOCAL
BUILDING OR
ELECTRICAL
CODES
M
T
* INSTALL SEPERATE
GFCI PROTECTED CIRCUITS,
DUPLEX RECEPTS NOT PROVIDED
HEATER
18
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Plumbing and Water Supply
Drain Information
Water Supply
A drain/overflow assembly (sold separately) must be in-
stalled on the bath, water tested, and connected to the sani-
tary system of the house. After opening the carton, inspect
for damage and verify that the kit is of the proper finish. In the
Jacuzzi Whirlpool Bath drain/overflow kit, note that the waste
flange, strainer, overflow cover and cover screws are pack-
aged in a separate package within the kit to protect the trim
finish. Follow the installation instructions provided with the
drain/overflow kit. After the drain is fully installed, test for
proper drainage. If the unit does not drain properly, rectify
this condition before proceeding with the installation. Jacuzzi
Whirlpool Bath is not responsible for removal and or reinstal-
lation costs.
Consult local authorities for plumbing code requirements
in your area.
IMPORTANT: Proper installation of the fill spout plumb-
ing and compliance with local codes are the responsibil-
ity of the installer. Jacuzzi Whirlpool Bath does not war-
rant connections of water supply fittings and piping, fill
systems, or drain/overflow systems. Nor is it responsible
for damage to the bath which occurs during installation.
CAUTION: A nonflammable protective barrier must be
placed between soldering work and bath unit to prevent
damage to the bath.
Shower Information
NOTE: Watertight installation of the drain is the installer's
responsibility. Drain leakage is excluded from the Jacuzzi
Whirlpool Bath warranty of this product.
Because of some baths' unique contour design, a rigid
shower door cannot readily be installed. If a shower is de-
sired, we recommend a hand-held shower be installed in con-
junction with a shower curtain, as this will allow the user to
control the direction of the spray.
Plumbing
NOTE: Proper installation of a shower is the responsibil-
ity of the installer. Jacuzzi Whirlpool Bath is not respon-
sible for damage to the unit or for water damage which
might occur due to its installation.
Pump, jets, and suction fittings for the whirlpool system
are factory plumbed in schedule 40 PVC piping.
All Jacuzzi Whirlpool Bath products are factory tested for
proper operation and watertight connections prior to shipping.
If leaks are detected, notify your Jacuzzi Whirlpool Bath dealer.
Do not install the unit.
Anti-Siphon Valve
Optional Anti-Siphon valve installation. Anti-Siphon valve
is not supplied with the tub. Consult your local plumbing code
requirements for the minimum height above the tub rim.
RECOMMENDED WATER SUPPLY CONNECTIONS (NOT ALL REQUIRE OR HAVE ALL FEATURES SHOWN)
ANTI-SIPHON VALVE
THESE ITEMS SHOWN
WATER RAINBOW® FILLSPOUT
DIVERTER HANDLE
6"
BATH RIM
FOR EXAMPLE ONLY
Consult local authorities
for plumbing code
HOT WATER SUPPLY
3/8" FPT x 1/2"
NOM. COUPLING
requirements in your area.
COLD
WATER
SUPPLY
3/4" FPT x 5/8" O.D.
COMPRESSION
3/8"x1/2"
NOM. ELL (2)
1/2" NOM.
ELL (TYP)
1/2" NOM. TEE
1/2" NOM. COPPER (TYP.)
1/2" FPT x 3/8" NOM.
ADAPTER
SHOWER HOSE 1/2" FPT
1/2" MPT x 1/2" MPT x 18" FLEXIBLE
Clean-Up After Installation
To avoid dulling and scratching the surface of the bath, never use abrasive cleaners. A mild liquid detergent and warm water
will clean soiled surfaces.
Remove spilled plaster with a wood or plastic edge. Metal tools will scratch the surface. Spots left by plaster or grout can be
removed if lightly rubbed with detergent on a damp cloth or sponge.
Paint, tar, or other difficult surface stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol).
NOTE: Use these chemicals only on SURFACE stains.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper.
You can restore the glossy finish to the acrylic surface of the bath with a special compound, Meguiar's #10 Mirror Glaze. If that
is not available, use automotive rubbing compound followed by an application of automotive paste wax.
Major scratches and gouges which penetrate the acrylic surface will require refinishing. Ask your Jacuzzi Whirlpool Bath
dealer for special instructions or visit our web site at http://www.jacuzzi.com/. To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
19
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATION
NOTE: These instructions pertain to all bath products manufactured by Jacuzzi Whirlpool Bath. Not all features dis-
cussed in this instruction pamphlet apply to all baths.
All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained
after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold
water continuously like pools or spas. If you want a unit designed to continuously hold water, see your Jacuzzi Whirlpool Bath
dealer for the complete line of whirlpool spas available.
Once the bath is installed, remove any residue or foreign materials left over from construction. Paint, tar, or other difficult surface
stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol). NOTE: Use these chemicals only on
SURFACE stains. Other dirt can be cleaned off with a mild liquid detergent on a damp cloth. Scrape off plaster with a wooden or
plastic edge; do not use metal scrapers, wire brushes or other metal tools, as they will damage the bath's surface.
Water Level
Close the drain and fill the bath until water is at least 1" to
2" (2,5 - 5,08 cm) above the highest jet (see water line indi-
cated in the illustration). Do not turn on the whirlpool sys-
tem at any time if the jets are not completely immersed in
water. Do not immerse the control panel by overfilling
the bath. Running the whirlpool system when there is insuf-
ficient water in the bath could result in water spraying outside
the bath area. Running the whirlpool system without water
will damage the recirculating pump.
FILL TO AT LEAST
1" - 2" ABOVE HIGHEST JET
1" - 2"
IMPORTANT: When exiting the bath, the water level will drop
below the jets which could result in water being sprayed out
of the unit. To prevent this, you must turn unit off before
exiting bath.
TYPICAL BATH FITTINGS
Controlling Whirlpool Action
ELECTRONIC CONTROL PANEL
The whirlpool action in your bath, controlled manually and
electronically, is influenced by three factors – direction of flow,
force of water, and force of air. Every bath manufactured by
Jacuzzi Whirlpool Bath that is equipped with fully adjustable
PowerPro® jets, are manually adjustable for direction and water
force. Some baths have additional jets which can be adjusted
for direction only. Baths equipped with 2 speed motors and
electronic controls can also influence water force and force
of air.
FULLY ADJUSTABLE JETS
SUCTION
COVER
Direction: To change the direction of the water flow, swivel
the jet nozzle to the desired angle. The jets can be directed
individually toward any location on your body to provide a
hydromassage. The jets can also be adjusted so that they all
point in the same direction (clockwise or counterclockwise)
to circulate the water in a circular motion around the bath,
causing a total whirlpool effect.
WATER RAINBOW
FILL SPOUT (OPTIONAL)
DRAIN/OVERFLOW
(OPTIONAL)
Water Force: The high volume, fully adjustable PowerPro®
jets can be manually adjusted to control the force of the water
coming into the bath. For robust action, increase the force of
the flow by rotating the jet handles to the left (counterclock-
wise). For a more gentle effect, rotate the handles to the right
(clockwise). Customize water force by lowering water volume
of one (1) jet(s) to increase water force in another jet(s). In
units with 2 speed motors the water force can be increased or
decreased using the electronic control. Never run the whirl-
pool system with all the jets closed.
JETS
FULLY
ADJUSTABLE
DIRECTIONALLY
ADJUSTABLE
Force of Air: Force of air is controlled electronically. Re-
fer to the Control panel instructions for details in adjusting
force of air.
20
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS (cont'd)
Electronic Control Panel Operation (with optional Chromotherapy/IllumatherapyTM lighting)
All tubs in this product line come with electronic controls and standard Chromotherapy or IllumatherapyTM. Read and follow the
operation instructions for the control system of your unit.
General Functions
This Jacuzzi tub is equipped with a seven button electronic control panel. The seven button panel controls a two speed pump/
motor, Chromotherapy or IllumatherapyTM lighting, air controls, and wave control. LED lights (in the control panel) indicate function
levels. When switching between functions, the LED for the inactive functions will dim and the active function will brighten.
The bath is equipped with a water level sensor(s). When the water level is below the sensor, the pump/motor can not be
activated. If the ON/OFF pump/motor button is pressed at this time, the pump/motor will not operate. When the water goes
above the water level sensor, the pump/motor can be activated. If the water level drops below the level sensor, the pump/motor
will shut OFF. To restart the pump/motor after the water level goes above the level sensor, the ON/OFF pump/motor button must
be pressed. The pump/motor will automatically shut off 30 minutes after the pump/motor was turned on.
NOTE: Ensure the water level sensor located inside the bath is free of any soap or dirt buildup.
Bath Light
Normal Operation (with the bath filled to the proper level)
Left Air Valve
Right Air Valve
Left Air Valve
Status LED
Pump/Motor Switch (ON/OFF )
Right Air Valve
Status LED
Pressing the
button will turn ON the two speed pump/
motor at HIGH speed. Pressing a second time will turn OFF
the pump/motor. To change speeds use the Toggle buttons.
Pump/Motor
Status LED
Pump/Motor Status LED
Toggle Buttons
ON/OFF
Pump/Motor
Wave Function
When the pump/motor is ON at HIGH speed all four LED
indicator lights will be lit. When the pump/motor is ON at
LOW speed the bottom LED indicator light will be lit.
Left Air Valve Switch
Wave Function Switch (ON/OFF )
Pressing this button activates wave action by opening
and closing both right and left air valves. Pressing a second
time will turn OFF the wave action.
Pressing this
button will acitvate the left air valves use
the Toggle buttons to increase/decrease air flow to the left set
of jets. The air flow can be adjusted from no air to maximum
air.
Left Air Valve Status LED
Toggle Buttons
The Left Air Valve Status LED will show four LED lights at
maximum air and only one LED light when the air is turned
OFF. Each additional LED indicates more air flow.
The Toggle buttons, up
other buttons to increase, decrease, or modify functionality.
Use the up arrow to increase and the down arrow to decrease.
and down
, act on each of the
Right Air Valve Switch
•
Pressing a toggle button after pressing the Pump/Motor
button will increase or decrease speeds on the Pump/Mo-
tor. If the pump/motor is on HIGH speed press the down
arrow to select LOW speed. If the pump/motor is on LOW
speed press the up arrow to select HIGH speed.
Pressing this
button will acitvate the right air valves. Use
the Toggle buttons to increase/decrease air flow to the right
set of jets. The air flow can be adjusted from no air to maxi-
mum air.
•
Pressing an up or down toggle button after pressing the
Right Air Valve Status LED
Bath Light button once will increase or decrease the white
light brightness. Pressing an up or down toggle button
after pressing the Bath Light button twice will begin cycling
the light colors. Leave the colors cycling or press the same
toggle button again to stop the color cycling. With the lights
stopped on a color pressing the Bath Light button a third
time will turn OFF the light. (A favorite color will be saved
ONLY when the cycling has been stopped on that color
The Right Air Valve Status LED will show four LED lights at
maximum air and only one LED light when the air is turned
OFF. Each additional LED indicates more air flow.
Bath Light Switch (ON/OFF )
Pressing this
button will turn ON the white bath light(s).
Pressing the Toggle buttons at this time will increase or de-
crease light intensity. Pressing the button a second time will
access the saved favorite color. To cycle lighting colors use
the Toggle button. Pressing the Toggle button again will stop
the light cycling. The color displayed when the cycle has been
stopped will be saved as your favorite color. Pressing the
button a third time to turn OFF the light.
and then turned OFF.)
NOTE: When switching between functions, the LED for
the inactive functions will dim and the active function will
brighten.
21
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS (cont'd)
RapidHeatTM
HIGH LIMIT RESET
HEATER ON
TheseunitshaveaRapidHeatTM heaterinstalledontheintakeordischargelines. The
HEATER ON
heater will help maintain the temperature of the water in the bath.
OVER HEAT
PROTECTION
Operation
With the heater installed and the whirlpool pump is operating, the heating func-
PUSH TO RESET
tion is totally automatic. No user control required.
Vacuum/Pressure Switch
The heater is equipped with a preset vacuum/pressure switch which will not al-
low the heater to turn ON if the pump is not running with water flowing through the whirlpool system.
High-Limit Switch
The heater includes an exclusive High-Limit switch. This safety circuit will not false trip from hot tap water. It will only turn off
the heater if the thermostat fails. To reset, press the button. If the high-limit trips frequently, contact your Authorized Electrical/
To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
22
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE INSTRUCTIONS
Cleaning the Bath
Purging the Whirlpool System
To clean your bath, simply use a mild, nonabrasive liquid
detergent solution. You can protect and restore the gloss to a
dulled acrylic surface by applying Meguiar's #10 Mirror Glaze,
a product specifically designed for use on acrylic finishes. If
Meguiar's is not available, an acrylic polish of equal quality or
automotive paste wax is acceptable.
NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED
AT LEAST TWICE A MONTH
To remove accumulations of bath residue from the whirl-
pool system, it is recommended that a whirlpool bath be
purged at least twice a month. For best results, however, we
recommend that you purge your whirlpool bath after each use
using, Systems Clean™, our exclusive two-part plumbing
system cleaner made specifically for whirlpool baths.
Never use abrasive household cleaners on any Jacuzzi
Whirlpool Bath product.
SystemsClean™isavailablethroughanauthorizedJacuzzi
Whirlpool Bath distributor or by calling us direct at 1-800-288-
4002.
Repairs to the Surface
Minor scratches which do not penetrate the color finish
can be removed by lightly sanding with 600-grit wet/dry sand-
paper. Restore the gloss using Meguiar's Mirror Glaze or au-
tomotive paste wax.
Systems Clean™ Instructions for use:
Refer to the instructions on the Systems Clean™ packet.
CAUTION: DO NOT USE WHILE BATHING! USE EXTREME
CAUTION WHEN HANDLING THIS PRODUCT!
Major scratches and gouges which penetrate the acrylic
surface will require refinishing. Ask your Jacuzzi Whirlpool
Bath dealer for special instructions.
Immediately after bathing and exiting the whirlpool bath,
leave the bath water in the tub and add more hot water. The
water level in the tub must be at least 2” (5,08 cm)above the
highest jet. NOTE: Inducted air from the hydromassage
system will cause the Systems Clean™ contents to foam
increasing odor. Turn OFF the whirlpool air control or turn it to
the lowest setting and pour in the entire contents of PACKET
#1 ONLY directly into the bath water. For bestresults, pour the
System Clean into the tub near the intake for the circulation
pump and be sure to avoid contact with your skin. Allow the
whirlpool to run for 30 seconds and then add PACKET #2
ONLY. It is important to use PACKET #1 before PACKET
#2 to avoid a strong odor. Allow the bath to run for 5 to 10
minutes then drain the tub completely. Refill the tub with cold
water and run for 2 to 3 minutes. Drain completely and rinse
off any residue. Remember to reset the air valves to your
bathing comfort level.
Bath Additives
NOTE:DONOTUSEOILOROILBASEDBATHADDITIVES.
If you want to use any kind of bath additive, use only a small
amount of low-foaming powder or crystal substance; the
whirlpool action intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath addi-
tives may increase the level of accumulations of bath residue
in the whirlpool system. If excess accumulations persist, you
should discontinue use of these products.
DANGER:Harmfulifswallowed. Eyeirritant. Protectyour
eyes, skin and mucus membranes from contact with this
product or its concentrated solution. A strong alkaline
product can cause severe burns to the eyes and skin.
If you have followed the standard purging instructions
above and still have an excess accumulation of bath residue
and desire an alternative cleaning mechanism, we recom-
mend SUPER SYSTEMS CLEAN™ PLUS manufactured by
Stearns Packaging to rectify this condition. This may be
obtained by contacting us at 1-800-288-4002. It is recom-
mended that you follow the instructions provided by the
manufacturer with the product. Repeated use may be neces-
sary. SUPER SYSTEMS CLEAN™ PLUS does not replace
the necessity to regularly purge your whirlpool system with
Systems Clean™ as recommended.
Spinning Jets Maintenance
(Models equipped with spinning jets)
If hair or other kind of debris gets caught in the bearings of
these jets, it could cause them to stop spinning. This may
require disassembly and cleaning. To do this, simply grab the
nozzle and pull straight out of the jet housing. The bearing
casing will be attached to the nozzle. These can be separated
by holding the casing and pushing the nozzle out from the rear
of the casing. After cleaning, reassemble in reverse.
PUSH FROM REAR
TO REMOVE
NOZZLE
NOZZLE
BEARING CASING
23
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE INSTRUCTIONS
SUCTION COVER/STRAINER ASSEMBLY
Suction/IntakeCover/StrainerMaintenance
Clean the suction/intake cover/strainer of hair and debris
when necessary. To do this, remove the center screw and
detach the square cover. Clean the cover by backflushing
debris from the holes. Replace the suction/intake cover im-
mediately after cleaning. When reinstalling, orient the cover/
strainer with the small notch at the bottom. The gasket must
be inserted into the groove of the cover/strainer before rein-
stalling onto the suction fitting.
COVER STRAINER
SUCTION
FITTING
SCREW
CAUTION: Keep hair a minimum of 6 inches (15,2 cm)
away from the suction/intake fitting at all times when the
whirlpool system is operating. Hair longer than shoulder
length should be secured close to the head, or a bathing
cap should be worn. Do not operate the whirlpool sys-
tem with the suction/intake cover removed! It is a safety
device and must always be in place on the suction fitting
to minimize the potential hazard of hair and/or body en-
trapment.
GASKET
NOTCH
LED LIGHT ASSEMBLY
Lighting (Chromotherapy lighting)
Your unit has Chromotherapy (LED) lighting. If the lights
fail to function contact your Jacuzzi Whirlpool Bath dealer.
There are no customer serviceable components on the Chro-
motherapy lighting.
LOCKING NUT
Replacement fixtures are available from your Jacuzzi
Whirlpool Bath dealer.
LIGHT BEZEL
SHELL
Lighting (optional IllumatherapyTM lighting)
If your unit has Illumatherapy (fiberoptic) lighting and the
lights fail to function contact your Jacuzzi Whirlpool Bath
dealer. There are no customer serviceable components on
the Illumatherapy lighting.
JET WITH FIBEROPTIC LIGHTS
DIN BOX (MOUNTED
ONTO FIBERGLASS SHELL)
LOCKING NUT
Replacement fixtures are available from your Jacuzzi
Whirlpool Bath dealer.
LIGHT BEZEL
FIBEROPTIC CABLE
(ROUTED TO WHIRLPOOL
CONTROL BOX)
SHELL
FIBEROPTIC CABLES
ROUTED FROM JET TO DIN BOX
24
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
General Whirlpool Bath Troubleshooting Guide
PROBLEM
PROBABLE CAUSES
REMEDY
Pump/Motor does not start.
No power to pump/motor.
Reset GFCI.
Pump/motor not plugged in.
Pump/motor faulty.
Insert plug fully into outlet.
Replace pump/motor assembly.
Open jets by rotating counterclockwise.
Jets are closed.
Control panel cable disconnected.
Reconnect control panel cable at control
or junction box.
Pump/Motor operates but no fully
adjustable jets are functioning.
Suction cover may be clogged.
Air valves closed.
With motor turned off, remove safety
cover and remove any debris. Clean
thoroughly before replacing. Replace
suction cover before operating.
Pump/Motor operates but air is not
injected into water.
Use electronic controls to open air
valves. Reset air valves to allow air flow.
Overtightened, O-ring may be
pinched or improperly seated, under
tightened.
Untighten unions check and reseat O-
ring. If O-ring has been pinched out of
shape, replace (refer to number below).
When tightening union nuts, hand
tighten only.
Water leakage from pump unions.
Motor thermal protection has deacti-
vated pump/motor due to overheat-
ing. (Supply voltage low.)
Let motor cool; thermal protection will
reset. Check for proper ventilation.
(Check supply voltage.)
Pump/motor shuts off by itself before
set time elapses.
GFCI tripped.
Reset GFCI. If it continues to trip do not
use this unit. Disconnect the unit and
have the problem corrected by a
licensed electrician before using.
Inadequate supply wiring.
No power to control panel.
Consult a licensed electrician to correct
wiring to unit.
Control panel not responding.
Power down the system by either unplug-
ging the unit or shutting off the power at
the house breaker panel. Wait 15 sec-
onds then power back up. Retry the sys-
tem by activating the feature that was not
responding.
Lighting does not work
Cable disconnected or broken.
Reconnect loose cable. Repair broken
cable wires.
NOTE: If unit is within the warranty period, contact Jacuzzi Whirlpool Bath Service Support at 1 - (800) 288-4002 with bath's serial
number before work is started. The Serial Number is located on the Specification/Serial Number Plate. See page 26.
25
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDENDUM
8-Button Electronic Control Panel for
the 240 V Control System
ELECTRICAL REQUIREMENTS
The Addendum for the 8-button Electrical Control Panel is attached to the Luxury® Salon™ Installation and Operation
Instructions, EL21000B. It provides the electrical requrements for the 240 V Control Systems.
8-Button Control Panel
SPECIFICATIONS FOR ALL UNITS
Electrical Service Requirements: Requires a separate dedicated GFCI-protected circuit
Blower: 120 VAC, 15 Amp, 60 Hz separate dedicated GFCI-protected circuit
Motor-Pump: 240 VAC, 15 Amp, 60 Hz separate dedicated GFCI-protected circuit
RapidHeat™: 120 VAC, 15 Amp, 60 Hz separate dedicated GFCI-protected circuit
DETAILS ON ThE 4-WIRE, hARD WIRINg
115 V
115 V
Neutral
Ground
4-Wire, hard Wiring
Copyright © 2008 by Jacuzzi Whirlpool Bath Products
Page ꢀ of 2
Publication GR86000A • 08-08
Download from Www.Somanuals.com. All Manuals Search And Download.
The following details will replace information found in the Combination Air Bath and Whirlpool Installation and Operation
Instructions, BR28000B (4/05) manual.
CAUTION: Install all electrical services on the right side of the bath. The blower has been moved from the left
side to the right side, next to the pump motor.
NOTE: The following art replaces the similar art found on
Page 1 of the Combination Air Bath and Whirlpool manual.
L
W
4"
H
2"
Heater
Blower Motor
SIDE VIEW
END VIEW
Allusion
NOTE: The following art replaces both pieces of similar art at the bottom of Page 3 of the manual. The art
"Blower Service Access" shows the blower on the left end of the bath, but it has been moved to the right end,
alongside the pump motor.
Blower
12"
Heater
Motor
FRONT
18"
MOTOR
SERVICE
AREA
18"
HEATER SERVICE AREA
Pump Motor, Blower Service Access (Required)
Jacuzzi™ Addendum, Control Panel Electrical Requirements
Page 2 of 2
Publication GR86000A • 08-08
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTHORIZED SERVICE
If you need a referral for a service company near you, or need assistance with operation or maintenance related
questions, please call our Service Support Department at 1-800-288-4002. Visit our web site at http://www.jacuzzi.com/
for products and services.
To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
When requesting service or technical assistance please have available both the model and serial number of your
unit. This information can be obtained from the product registration card provided with your unit. If the card has
been misplaced, this information can be obtained from the specification/serial number label on the unit itself (for
location of specification/serial number label see below).
BATH PRODUCTS
Whirlpool baths: The label is located on the wall of the bath near the pump/motor.
Non-jetted baths: The label is located next to the overflow.
SPECIFICATION/SERIAL NUMBER PLATE
CORE NUMBER - SERIAL NUMBER
XXXX - XXXXXX
Applicable Electrical Specifications for your unit.
MODEL # XXXXXXX
NAME XXXXX
COLOR XXXXX
MFG # XXXXX
SER # XXXXXX
ELECTRICAL SPECIFICATIONS
PRINTED IN THIS AREA
YOU WILL FIND YOUR
SERIAL NUMBER HERE.
THIS PRODUCT MEETS OR EXCEED
MADE IN
THE FOLLOWING STANDARDS
USA
BATH & SPA xxxx xxxx.x
SHOWER BASES xxxx xxxx.x
Appropriate Safety Compliance Logos for your unit.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of
this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.
Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath
P.O. Box 702168, Dallas, TX 75370-2168
Service Support: (800) 288-4002
©2005 Jacuzzi Whirlpool Bath K339000X 3/06
Printed in the U.S.A.
Printed on Recycled Paper
26
Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Jacuzzi Whirlpool Bath Limited Warranty
Designer/Luxury Collection Bath Product
WARRANTY COVERAGE
Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool
Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair
or replace, at its sole option, the unit or its equipment in accordance with the following terms and conditions.
TWO YEAR LIMITED WARRANTY ON BATHS
Our limited warranty on Designer Collection Bath products is for two (2) years. Our warranty covers the unit and factory-installed
components (e.g., pump, motor) against defects in material or workmanship. Warranty coverage begins on the date the unit was originally
purchased by the user.
FIVE YEAR (PARTS ONLY) LIMITED WARRANTY ON PUMP AND MOTOR
Our limited warranty on the pump and motor is for five (5) years for parts only. Warranty coverage begins on the date the unit was originally
purchased by the user.
NINETY DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
Our limited warranty on options and accessories manufactured by the Company is for ninety (90) days for parts only. Our warranty covers
options and accessories manufactured by the Company (e.g., fill spout kits, trim kits, skirts) against defects in materials or workmanship. Warranty
coverage begins on the date the option or accessory was originally purchased by the user.
WARRANTY LIMITATIONS
Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other person, or resulting
from, without limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.); modification of any type for any reason
(including modification to meet local codes); improper installation (including installation not in accordance with instructions and specifications
provided with the unit); connections supplied by the installer of the equipment; improper voltage supply or unauthorized electrical modification;
misuse; incorrect operation, or lack of proper routine maintenance; operation of the unit without specified minimum amount of water or at
inappropriate water temperature; use of abrasive or improper cleaners; or acts of God, such as lightning, floods, earthquakes, etc.
In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any
cause (e.g., water damage to carpet, ceiling, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts
when pool and/or spa chemicals are used in the unit; optional bath equipment not manufactured by the Company but supplied by Dealer, installer
or the Company; the unit's prior usage as an operational display; or defects that should have been discovered before installation. This limited
warranty does not include: labor, transportation, or other costs incurred in the removal and/or reinstallation of the original unit and/or installation
of a replacement unit; any costs relating to obtaining access for repair; or loss of use damage, including loss of sales, profit or business advantage
of any kind under any circumstances. Bath units are excluded from any warranty coverage if any addition, deletion, or modification of any kind
whatsoever has been made to the unit (or to any component).
Warranty coverage is provided in the United States of America and Canada.
EXCLUSION OF IMPLIED WARRANTIES
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR
TO THE FULLEST EXTENT ALLOWED BY LAW.
NOTICE: Thiswarrantygivesyouspecificlegalrights, andyoumayalsohaveotherrightswhichvaryfromstatetostate. Therearenowarranties
applicable to Jacuzzi Whirlpool Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company
will not be responsible for any statements or representations made in any form that go beyond, are broader than or are inconsistent with any
authorized literature or specifications furnished by the Company.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages,
so the above limitations and exclusions may not apply to you.
RETURN OF WARRANTY CARD
The attached Warranty Registration Card MUST be filled out by the purchaser within thirty (30) days from purchase and mailed to Jacuzzi
Whirlpool Bath in order for this warranty to become effective.
Jacuzzi Whirlpool Bath
P.O. Box 702168
Dallas, TX 75370-2168
Download from Www.Somanuals.com. All Manuals Search And Download.
RESPONSIBILITIES OF OTHERS
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are
responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer
of this responsibility. In the event of a problem, the unit must not be installed. The Company is not responsible for failures or damage that could
have been discovered, repaired, or avoided by proper inspection and testing prior to installation.
Damage occurring in transit is the responsibility of the carrier. The user or installer MUST open the crate and inspect the unit for damage when
it is delivered. If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure
of the carrier to respond should be reported to the seller and the carrier. Your freight claims should be filed promptly thereafter.
It is the responsibility of the installer, building contractor, or user to provide access for service. The Company is not responsible for any costs
relating to obtaining access for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.
Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter
is the responsibility of the user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (Options and accessories manufactured by the
Company are warranted for ninety (90) days from the original date of purchase for parts only.)
The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these
requirements at the time of purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city,
county, or state building codes in U.S.A. or municipal or provincial codes in Canada.
WARRANTY SERVICE
For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such
firms are not agents or representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or
type covered by the warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Service Agent or Warranty Service Department
Representative of the nature of the problem during the warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided
totheforegoingbytheuserprovingthatthefailureoccurredorwasdiscoveredwithinthewarrantyperiod;anauthorizedindependentserviceperson
or Company representative has been permitted to inspect the unit during regular business hours within a reasonable time after the problem was
reported by the user.
In order to obtain warranty service, consult your local telephone book for the location of the nearest Jacuzzi Whirlpool Bath Authorized Service
Agent. Describe the problem and the Authorized Service Agent will inspect the unit and provide the required warranty service.
If you are unable to contact a Jacuzzi Whirlpool Bath Authorized Service Agent, call or write:
Jacuzzi Whirlpool Bath
Warranty Service Department
14801 Quorum Dr., Suite 400
Dallas, TX 75254
Call: (800) 288-4002
To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied
by the Company, call or write the above. Provide a description of the problem and proof of purchase. You will be instructed how to obtain
replacements and where to return, at your expense, the failed component(s), option(s), or accessory(ies).
All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender
terminates the Company's warranty obligation.
©2005 Jacuzzi Whirlpool Bath K339000X 3/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|