ESPREE™ BATHTUB
SERIES
INSTALLATION AND OPERATION INSTRUCTIONS
Jacuzzi® Luxury Bath
14525 Monte Vista Avenue
Chino, CA 91710
1-800-288-4002
U961000
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Contents
Contents.......................................................................................................................................................................... 3
Product Information......................................................................................................................................................... 3
Safety instructions........................................................................................................................................................... 4
Operational Safety instructions........................................................................................................................................ 6
Introduction...................................................................................................................................................................... 8
Inspection and Testing................................................................................................................................................... 10
Framing and Support......................................................................................................................................................11
Electrical Connections................................................................................................................................................... 12
Drop-in Installation......................................................................................................................................................... 14
3-Wall Alcove Installation............................................................................................................................................... 16
Skirt Installation............................................................................................................................................................. 16
Cleanup......................................................................................................................................................................... 17
Operation....................................................................................................................................................................... 17
Whirlpool Control........................................................................................................................................................... 18
Purging the Whirlpool System....................................................................................................................................... 19
Bathtub Additives........................................................................................................................................................... 19
Maintenance.................................................................................................................................................................. 19
Troubleshooting Procedures. ........................................................................................................................................ 20
Technical Specifications. ............................................................................................................................................... 21
Authorized Service. ....................................................................................................................................................... 26
Warranty. ....................................................................................................................................................................... 27
Product Information
Save these instructions for future use. Use the form below to record your model and serial number for future
reference.
Date Purchased
Purchased From
Installed By
Serial Number
Model
Installer: Leave the manual for the homeowner.
Homeowner: Read this manual and keep for future reference.
Installation and Operation
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Safety Instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS.
This is a professional grade product. A knowledge of construction techniques,
plumbing and electrical installation according to codes are required for proper
installation and user satisfaction. We recommend that a licensed contractor perform
the installation of all Jacuzzi® Luxury Bath products. Our warranty does not cover
improper installation related problems.
CAUTION: When using this unit, basic precautions should always be performed,
including the following:
• READ AND FOLLOW ALL
INSTRUCTIONS. SAVE THESE
INSTRUCTIONS.
Use this unit only for its intended use as described in this manual.
•
Do not use attachments not recommended by the manufacturer.
Never drop or insert any object into any opening.
•
WARNING: RISk Of ACCIDENTAL INJURy OR DROWNING!
Do not permit children to use this unit unless they are closely
supervised at all times. Do not use hydromassage bathtubs unless
all suction guards are installed to prevent body and hair
entrapment. Never operate the hydromassage bath if the suction
cover is broken, damaged or missing
DANGER: RISk Of SEvERE INJURy fROm ELECTRIC SHOCk OR DEATH
fROm ELECTROCUTION!
This unit must be connected only to a supply circuit that is
protected by a 15 amp ground fault circuit interrupter (GFCI). Such a
GFCI should be provided by the installer and should be tested on a
routine basis. To test the GFCI, push the test button. The GFCI
should interrupt power. Push the reset button. Power should be
restored. If the GFCI fails to operate in this manner, the GFCI is
defective. If the GFCI interrupts power to the bathtub without the test
button being pushed, a ground current is flowing, indicating a
possibility of an electric shock. Do not use this hydromassage
bathtub. Disconnect the hydromassage bathtub and have the
problem corrected by a qualified service representative before using.
WARNING: RISk Of ELECTRIC SHOCk!
Do not permit electrical appliances (such as a hair dryer, lamp,
telephone, radio or television) within 60” (1524mm) of this
hydromassage bathtub. Connect only to a circuit protected by a
ground fault circuit interrupter (GFCI). (For permanently connected
units) A green colored terminal (or a wire connector) marked “G,”
“GR,” “GROUND,” or “GROUNDING”) is provided within the
terminal compartment. To reduce the risk of electric shock, connect
the terminal or connector to the grounding terminal of your electric
service or supply panel with a conductor equivalent in size to the
circuit conductors supplying the equipment.
Page 4
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Safety Instructions (Cont)
WARNING:
Do not operate this unit without the guard over the intake for
the circulation pump (suction cover/strainer).
CAUTION:
This equipment is intended for indoor use only. Install the
equipment in accordance with these instructions. Use supply
wires that are suitable for 167°F (75°C), including the
temperature rating of the supply conductors to be used. This
unit should be electrically grounded and installed by a licensed
contractor, electrician, and plumber. Building materials and
wiring should be routed away from the motor/pump or blower or
other heat producing components of this unit. A pressure
wire connector is provided on the exterior of the motor/pump
and heater to permit connection of an No. 8 AWG solid copper
bonding conductor between this unit and all other electric
equipment and exposed metal in the vicinity, as needed to
comply with local requirements.
When using this electrical equipment, basic safety precautions should
always be followed, including the following:
WARNING:RISK OF ACCIDENTAL INJURY OR DROWNING! CHILDREN
SHOULD NOT USE HYDROMASSAGE BATHTUB WITHOUT
ADULT SUPERVISION.
WARNING:RISK OF ACCIDENTAL INJURY OR DROWNING! DO NOT
USE HYDROMASSAGE BATHTUB UNLESS ALL SUCTION
GUARDS ARE INSTALLED TO PREVENT BODY AND HAIR
ENTRAPMENT.
WARNING:TO AVOID INJURY, ExERCISE CARE WHEN ENTERING OR
ExITING THE HYDROMASSAGE BATHTUB.
WARNING:RISK OF ACCIDENTAL INJURY OR DROWNING! DO NOT
USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE OF A
HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO
AVOID UNCONSCIOUSNESS AND POSSIBLE DROWNING.
WARNING:RISK OF FETAL INJURY! PREGNANT OR POSSIBLY
PREGNANT WOMEN SHOULD CONSULT A PHYSICIAN BEFORE
USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A
HEATER.
WARNING:RISK OF HYPERTHERMIA AND POSSIBLE DROWNING: DO
NOT USE A HYDROMASSAGE BATHTUB EQUIPPED WITH A
HEATER IMMEDIATELY FOLLOWING STRENUOUS ExERCISE.
SAVE THESE INSTRUCTIONS .
Installation and Operation
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Operational Safety Instructions
WARNING:
RISk Of HyPERTHERmIA AND POSSIBLE DROWNING!
Do not use a hydromassage bathtub equipped with a heater
immediately following strenuous exercise.
WARNING:
RISk Of ELECTRICAL SHOCk!
Do not operate hydromassage system unless the bath is
•
filled with water to at least 1-2˝ (25-51 mm) above the highest
jet.
Do not immerse the control panel by overfilling the bath.
•
When cleaning your bath, do not use abrasive substances
•
which will damage the bath’s surface.
To prevent discoloration of the acrylic finish, do not fill the
•
bath with water in excess of 140°F (60°C).
WARNING:
PROLONGED ImmERSION IN HOT WATER mAy INDUCE
HyPERTHERmIA!
Hyperthermia occurs when the internal temperature of the body
reaches a level several degrees above the normal body
temperature of 98.6°F (37°C). The symptoms of hyperthermia
include an increase in the internal temperature of the body,
dizziness, lethargy, drowsiness and fainting. The effects of
hyperthermia include:
A.
B.
C.
D.
E.
F.
Failure to perceive heat.
Failure to recognize the need to exit the bath.
Unawareness of impending hazard.
Fetal damage in pregnant women.
Physical inability to exit the bath.
Unconsciousness resulting in danger of drowning.
WARNING:
WARNING:
RISk Of fETAL INJURy!
Pregnant or possibly pregnant women should consult a
physician before using a hydromassage bathtub equipped with
a heater.
Keep body and hair a minimum of 6˝ (152mm) away from the
suction fitting at all times when the hydromassage system is in
operation. Hair longer than shoulder length should be secured
close to the head.
Page 6
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Operational Safety Instructions (cont)
WARNING:
The use of alcohol, drugs or medication can greatly increase
the risk of fatal hyperthermia. People using medications or
having an adverse medical history should consult a physician
before using a hydromassage bathtub equipped with a heater.
WARNING:
WARNING:
Do not tamper with user-operated controls or such devices.
Use this unit only for its intended use as described in this
manual. Do not use attachments not recommended by the
manufacturers.
WARNING:
WARNING:
To avoid injury, exercise caution when entering or exiting the
hydromassage bathtub.
Do not use hydromassage bathtub unless all suction guards
are installed to prevent body and hair entrapment. Never
operate the hydromassage bath if the suction cover is broken,
damaged or missing.
WARNING:
CAUTION:
Water temperature in excess of 104°F (40°C) may be injurious
to your health. Check and adjust water temperature before use.
Test the ground fault circuit interrupter protecting this appliance
periodically in accordance with manufacturer’s instructions.
ImPORTANT:
ImPORTANT:
Read the complete instructions provided in this manual before
beginning installation.
For optimal operation, the water level must remain at 1˝ to 2˝
(25mm to 50mm) above the highest jet; do not use oil-based
bathtub additives in your hydromassage bathtub.
The Company has obtained applicable code (standards) listings generally available
on a national basis for products of this type. It is the responsibility of the
installer/owner to determine specific local code compliance prior to installation of the
product. The Company makes no representation or warranty regarding, and will not
be responsible for any code compliance. Product specifications are subject to
change without notice.
Installation and Operation
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Introduction
fLUSH TO THE WALL
The drain/overflow of the bath extends below the bottom
of the bath. Please refer to the “Technical Specifications”
section for dimensions and rough-in information.
Tile
Mortar/
The floor structure beneath the bath must be able to
support a total weight of bath, water, and bather. Refer
to the table under total weight for your model.
Adhesive
Sealant
The unit must be supported from the bottom of the bath and
not from the bath rim or tile flange. If the subfloor is level
and a continuous surface, no other preparation is necessary.
You can proceed to install the bath. If the subfloor is not
level, you must level the entire surface prior to installing
the bath. The use of materials that shim or provide a level
installation are allowed provided the method used will insure
a level bath that is supported from the bottom. Materials that
may be used are a floor leveling compound, mortar, plaster
or minimal expansion structural foam having a density of a
minimum of 5 lbs./cubic ft.; however, the bath must remain
level in order for it to drain properly and all foam feet must
make full contact with the leveling material. Both sides of
a joint or splice of subfloor should be level to each other.
When attaching baths with flanges to stud wall, use shims to
fill any gaps between the bath flange and studs.
1˝ x 4˝ (not for
support)
Flashing
SEmI-SUNkEN
Mortar/
Adhesive
Tile
The rim of the bath is not designed to support weight. If
finish material is to overlap or contact the bath, the added
weight must be fully self-supporting.
Sealant
1˝ x 4˝ (not for
support)
Flashing
Subfloor
OPTIONAL TILE fLANGE kIT
Finishing Material
Mortar
Cement Board
Plastic Filler
Bath Rim
Silicone Selant
Flange
1˝ x 4˝ (not for
support)
Screw
Stud Wall
Page 8
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Typical flange mounting Detail
Tile
Tile
Tile Adhesive
Cement Board
Tile Adhesive
Cement Board
Wood Stud
Mounting
Screws
Mounting
Screws
Wood Stud
Flange
Flange
1˝ x 4˝ (not for
support)
Caulking
Flange
Caulking
Flange
Wood Stud
Shim
Wood Stud
Shim
The shims may be used to tighten and secure any remaining gaps between the flange and the stud.
Undermount Installation Options
The undermount allows for the opportunity to be flexible in the design and location of the bathtub. Examples are
shown for possible installations. Refer to the “Undermount Installation” section.
CORNER
NICHE
fREE STANDING
Installation and Operation
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Inspection and Testing
visual Inspection
Remove the bathtub from the shipping carton. Be careful not to scratch the surface of the bathtub on exposed
staples. Remove the staples or fold them into the carton. Retain the carton until satisfactory inspection of the
product has been made. Do not lift the bathtub by the plumbing at any time; handle by the shell only.
XX
Inspect the shell and bathtub components. Should inspection reveal any damage or defect in the finish or visible
damage to any components, do not install the bathtub. Damage or defect to the finish claimed after the bathtub
is installed is excluded from the warranty. Jacuzzi Luxury Bath’s responsibility for shipping damage ceases upon
delivery of the products in good order to the carrier.
YX
Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the
published warranty information packed with the product or in the back of this manual.
ZX
Bathtub Water and Operational Test
All bathtub units are factory tested for proper operation and watertight connections prior to shipping. However, the unit
must be retested by the installer prior to installation. Jacuzzi Luxury Bath is not responsible for any defect that could
have been discovered, repaired, or avoided by following this inspection and testing procedure:
Place the bathtub on a level surface, near appropriate electrical supply, water supply, and water drainage. A
driveway is a suitable choice.
XX
Seal the drain and overflow hole with tape or a stopper and fill the bathtub to the bottom of the overflow hole.
Allow bathtub to stand for 5 minutes.
Plug in motor/pump and turn unit on. Confirm that all features function as described in the Operation section of
this manual. Do not install the bathtub if bathtub fails to operate as described.
YX
ZX
[X
Visually inspect all joints for leaks. Do not install the bathtub if leaks are detected.
Return bathtub to box or otherwise protect from damage until time of installation.
\X
]X
Page 10
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
framing and Support
A Technical Specifications section has been included with in this manual. The Technical Specifications section will
contain pertinent information regarding your Jacuzzi Luxury Bath product.
Common Access Locations
Frame out the space where the bathtub is to be located. The
following should be taken into consideration when preparing
the area:
Dimensions provided on rough-in diagrams are
nominal. Measure your actual unit upon receipt and
build according to the actual dimensions.
•
The floor structure beneath the bathtub must be able
12˝
(304mm)
•
to support the total weight of the bathtub, water and
bather.
Primary
Access
18˝
(457mm)
The unit must be supported from the bottom of the
•
Secondary
Access
bathtub and not from the bathtub rim. For drop-in
installations, take into account the thickness of the
surround material and finishing material (marble, tile,
etc.).
Motor/Pump
18˝
(457mm)
Ensure the rim will rest on a level surface.
•
•
Per code, access must be provided to the motor/pump
for your specific model. Primary and secondary service
access locations are shown in the rough-in diagrams
contained in the Technical Specifications Manual.
It is the responsibility of the installer, building
contractor, or owner to provide access for service.
Jacuzzi is not responsible for any costs relating to
obtaining access for repair. The owner shall bear such
costs and, if appropriate, must seek recovery from the
installer.
20˝
(508mm)
C
Motor/Pump
B
A
36˝
Provide adequate ventilation for cooling and supply
sufficient air for the motor/pump. Do not insulate
around the equipment.
•
(914mm)
24˝
(609mm)
Your bathtub may have motor/pump parts that extend
•
= Primary access
A
beyond the rim of the bathtub. Refer to the rough-in
diagrams included in the warranty pack and
construction framing to correctly accommodate.
= Acceptable alternative if access A is not possible
= Secondary access for equipment (optional)
B
C
Left hand unit access is on the opposite side (mirror).
Subfloor
Prepare the subfloor for the drain and ensure that the area is level.
The drain/overflow of the bathtub extends below the bottom of the bathtub. Identify the drawing in the Technical
Specifications Manual that corresponds with your bathtub.
XX
Make appropriate cuts to the subfloor to accommodate the drain.
YX
ZX
Jacuzzi’s Tru-Level™ base is a standard feature on all bathtubs. If the subfloor is level and a continuous surface,
no other preparation is necessary. Proceed to the “Installation” section.
If the subfloor is not level, you must level the entire surface prior to installing the bathtub. The materials used
will insure that the bathtub is supported from the bottom. These materials include: leveling compound, mortar,
plaster or minimal expansion structural foam (having a density of a minimum 5lbs/cubic foot). The bathtub must
remain level in order for it to drain properly and must make contact with the leveling material. Both sides of a joint
or splice of subfloor should be level to each other.
[X
Installation and Operation
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Electrical Connections
Risk of electric shock. Connect only to a circuit
protected by a GFCI.
When using electrical products, basic precautions
should always be followed:
Always follow local building and electrical codes.
•
Grounding is required. The unit should be
•
Reset
Test
installed and grounded by a qualified electrician.
A heater comes standard on all Espree™ corner
bath models.
Two separate GFCI protected circuits are required.
A separate, 120VAC, 15 Amp GFCI circuit is required for
the pump/motor.
If installing the optional heater, a separate and dedicated
120VAC, 15AMP, GFCI protected circuit is required.
If you are installing the optional heater, please refer to the
provided installation and operation manual that comes
packaged with the heater.
Risk of component overheat. Do not use electric extension cord to power this unit.
Operating the motor/pump without enough water in the bathtub can cause leaking and permanent damage.
Pump/motor
For the pump/motor, install a 120 VAC, 15AMP,
GFCI duplex outlet to the stud wall underneath the
bathtub at 4˝ (101mm) above the floor. The duplex
outlet is not supplied.
XX
3-Prong Plug
Duplex Outlet
(Not Included)
The duplex outlet must be mounted 4˝ (101mm)
above the floor line, or in accordance with local
building and electrical codes.
On the corner bathtubs, or 6060 bathtubs, a duplex
junction box has been provided. To access, remove
skirt access panel. See top views in Rough-In
section for location.
Heater
M
T
A separate GFCI protected outlet (not provided) is
required for pump/motor and is to be installed in the
junction box. The junction box is to be hard wired.
The motor is grounded to the junction box at the
factory.
3-Prong Plug
Duplex Outlet
(Not Included)
Using a #8 solid copper wire, ground the pump
motor to the house electrical panel, or approved
local ground. A grounding lug is provided on the
pump motor
At initial start-up, and before each use thereafter
with power ON, push the GFCI test button. The
reset button should pop out.
YX
[X
Push this button in to reset. If the interrupter fails to operate in this manner, there is a ground current flowing or a
device malfunction, indicating the possibility of electrical shock.
Turn OFF power and do not use the bathtub until the source of the problem has been identified and corrected.
Page 12
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Electrical Connection 6060 w/Heater
6060 Corner Unit
On the 6060 with integral skirt, one junction box has
been provided for the pump/motor. The motor is bonded
to the junction box at the factory. To access, remove skirt
access panel.
Bonding
A separate 120 VAVAC, 15 AMP dedicated circuit
with GFCI protected outlet (commercially available) is
required for heater and is to be installed in a junction box.
The junction box is to be hard wired.
Follow the bonding instructions below:
With a #8 solid copper wire, bond the heater to the
house electrical panel or approved local bond. A
bonding lug is provided on the heater.
XX
For Heater
Initial Start-Up
For Pump/Motor
Push the GFCI test button. The reset button should
pop out.
XX
Push this button in to reset. If the interrupter fails
YX
to operate in this manner, there is a ground current
flowing or a device malfunction, indicating the
possibility of electrical shock.
GFCI
Bonding to
Pump/Motor
Turn off power and do not use the bath until the
source of the problem has been identified and
corrected.
ZX
J-Box
Power Cord
(Commercially Available)
GFCI
Bonding to
RapidHeat™
(Commercially Available)
Heater ON
Overheat
Protection
Press to Reset
J-Box
Power Cord
(Commercially Available)
Installation and Operation
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Drop-in Installation
Before you begin your installation, please read the following:
Observe all local and building codes.
•
Determine which tools will be used during the installation.
•
Additional bathtub drain parts and plumbing are commercially available at plumbing and hardware stores.
Drain/Overflow rough-in information is included with your bathtub in the installation instruction manual.
•
•
Complete the bathtub surround installation.
Install drain/overflow according to the
manufacturer’s instructions. Refer also to the
Technical Specifications section.
XX
Watertight installation of the drain is the installer’s
responsibility. Drain leakage is excluded from the
Jacuzzi Luxury Bath warranty of this product.
Tile
Subfloor
Install the faucet at this time. It is recommended
that the faucet be installed by a qualified plumber.
YX
Sealant
Proper installation of the spout plumbing and
compliance with local codes are the responsibility of
the installer. Jacuzzi Luxury Bath does not warrant
connections of water supply fittings and piping,
fill systems, or drain/overflow systems. Nor is it
responsible for damage to the bathtub which may
occur during installation.
Mortar or
Adhesive
Flashing
1˝ x 4˝
(25mm x 101mm)
Not For Support
A non-flammable protective barrier must be placed
between the soldering work and the bathtub unit to
prevent damage to the bathtub.
Exploded View
Prepare the cut-out hole for the bathtub using the
cutout dimensions listed in the specifications table
in the Technical Specifications section.
ZX
Complete all deck finish work and cover to protect
from damaging while placing the bathtub.
[X
Insulation may be placed within the bathtub
surround.
Tile or Finished
Surface
Provide adequate ventilation around the motor/
pump to ensure sufficient airflow and cooling.
Scrap Lumber
Scrap Lumber
Turn off power supply to dedicated GFCI protected
circuits.
\X
Substrate
Minimum 3˝
(76mm)
Clearance
Place a piece of scrap lumber on each of the ends
]X
of the cutout – this will be used as a temporary
support prior to lowering the bathtub fully into the
opening.
Support
Member
Level Subfloor
Page 14
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Drop-in Installation (con’t)
Install the unit, inserting the motor/pump end first,
lowering the bathtub into the opening as shown in
the illustration.
Tile or
Finished
Surface
^X
Scrap Lumber
Substrate
DO NOT use plumbing fixtures or lines to lower the
unit. Allow the bathtub to rest on the supports.
Level Subfloor
Member Support
Inspect all fittings, plumbing, and control lines
after inserting to insure the components are not
damaged, disconnected, or contacting the finish
surface substrate or support members.
Connect flex water supply lines to faucet and plug
power cords into GFCI outlets.
_X
Remove scrap lumber and lower the bathtub
fully into the opening and align the bathtub and
connect the drain.
`X
Level Subfloor
Turn on the power supply to the dedicated GFCI
protected circuits and check system operation.
aX
Caulk around the perimeter of bathtub to seal the
space between the rim and the finished deck.
Floating
Floor
Compound
Uneven
Subfloor
Installation and Operation
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
3-Wall Alcove Installation
Install the drain/overflow according to the
manufacturer’s instructions. Refer also to the
Technical Specifications section.
XX
Cement Board
Mortar
Finishing
Material
Watertight installation of the drain is the installer’s
responsibility. Drain leakage is excluded from the
Jacuzzi Luxury Bath warranty of this product.
Plastic Filler
Silicon/Sealant
Bath Rim
Install the faucet at this time. It is recommended that
the faucet be installed by a qualified plumber.
YX
Screw
Tile Flange
Install the flange (purchased separately) according
ZX
to the instructions that are included with the kit. If the
bathtub is equipped with an integrated flange, skip this
step.
Stud Wall
1˝ x 4˝ (not for
support)
Place the bathtub into the niche. Screw the flange to
[X
the wood stud. It may be necessary to shim the unit
to close up any gaps between the wood stud and the
flange.
Insulation may be placed within the bathtub surround.
Turn off the power supply to the GFCI protected
circuit.
\X
]X
Tile
Align the bathtub and connect the drain.
Connect flex water supply lines to faucet and plug
power cords into GFCI outlet.
^X
Stud Wall
_X
Cement Board
Tile Adhesive
Inspect all fittings, plumbing, and control lines after
`X
inserting the bathtub to insure the components are
not damaged, disconnected, or contacting the finish
surface substrate or support members.
Caulking
Mounting
Screw
Turn on the power supply to the dedicated GFCI
protected circuits and check system operation.
Complete all finish work around the perimeter of
bathtub to seal the space between the rim and the
finished deck.
aX
Tile Flange
Stud
1˝ x 4˝
(not for
support)
Skirt Installation
Bathtubs with an Integral Skirt
Screw skirt flanges into wall studs.
It may be necessary to shim the unit to close any
gaps between wall studs and the flanges.
XX
Finishing
Materials
Complete finish work over skirt flange.
Caulk around the perimeter of the skirt to seal the
space between the skirt and the finished deck.
Green Board
YX
ZX
Caulking Bead
Rim of Bathtub
Stud
Skirt Panel
Floor
Page 16
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Cleanup
To avoid dulling and scratching the surface of the bathtub, never use abrasive cleaners. For most soiled surfaces, a
mild liquid detergent and warm water is sufficient. The following is also recommended:
Remove spilled plaster with a wood or plastic edge. Spots left by plaster or grout can be removed if lightly rubbed
•
with detergent on a damp cloth or sponge. Do not use metal scrapers, wire brushes or other metal tools, as they
will damage the bathtub’s surface.
Paint, tar, or other difficult stains can be removed with Fantastik® or soapy water.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry
•
•
sandpaper. You can restore the glossy finish to the acrylic surface of the bathtub with a special compound,
Meguiar’s #10 Mirror Glaze. If that is not available, use automotive rubbing compound followed by an application
of automotive paste wax.
Major scratches and gouges which penetrate the acrylic surface will require refinishing. Call Jacuzzi Luxury Bath
to find a service agent in your area.
•
Operation
All bathtubs manufactured by Jacuzzi Luxury Bath are
designed for “fill and drain,” which means the bathtub
Fill to at least 1˝ to 2˝
above highest jet
should be drained after each use and filled with fresh
water by the next bather. This is a health precaution,
as these bathtubs are not designed to hold water
continuously like pools or spas.
Close the drain and fill the bathtub until water is at
least 1˝ to 2˝ (25mm to 51mm) above the highest jet
(see water line indicated in the illustration). Do not turn
on the whirlpool system at any time if the jets are not
Air Control
Knobs (2)
completely immersed in water. Running the whirlpool
system when there is insufficient water in the bathtub
could result in water spraying outside the bath area.
Running the whirlpool system without water will damage
the recirculating pump.
ON/OFF
Button
Overflow
Handle
Jets
When exiting the bathtub, the water level will drop
below the jets which could result in water being
sprayed out of the unit.
Suction Cover
Drain
ON/Off Button
The ON/OFF button, conveniently located on the bath,
allows you to turn the whirlpool system on and off while in
the bath. Simply push down on the switch button to turn on
the whirlpool system. To turn the system off, push down on
the button again.
ON/OFF
Button
Installation and Operation
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Rapdheat™ Operation
Once the heater is installed and the whirlpool pump is operating, the heating function is totally automatic. The heater
will help maintain the temperature of the water in the bath. The heater is designed to help maintain the temperature of
the bath water once the water is added at the desired temperature level. It does not replace the need to have adequate
hot water supply for the filling of the bath.
vacuum Switch
The heater is equipped with a preset vacuum switch which
will not allow the heater to turn ON if the pump is not running
with water flowing through the whirlpool system.
Heater ON
Overheat
Protection
High-Limit Switch
The heater includes an exclusive High-Limit switch. This
Press to Reset
safety circuit will not false trip from hot tap water. It will only
turn off the heater, if the thermostat fails. To reset, press the
button.
Heater On Indicator
The light will be illuminated any time the heater is operating.
Whirlpool Control
The whirlpool action in your bath is influenced by three
factors – direction of flow, force of water, and force of air. All
baths manufactured by Jacuzzi Whirlpool Bath are equipped
with fully adjustable PowerPro® jets, which are adjustable
for all three factors. Some baths have additional directionally
adjustable jets which can be adjusted for direction and flow
of air only.
Direction
To change the direction of the water flow, swivel the jet
nozzle to the desired angle. The jets can be directed
Air Induction Control Knobs
individually toward any location on your body to provide a
hydromassage. The jets can also be adjusted so that they all
point in the same direction (clockwise or counterclockwise)
to circulate the water in a circular motion around the bath,
causing a total whirlpool effect.
Water force
The high volume, fully adjustable jets can be adjusted to
control the force of the water coming into the bath. For
robust action, increase the force of the flow by rotating the
jet handles to the left (counterclockwise). For a more gentle
effect, rotate the handles to the right (clockwise).
Large Adjustable Jets
Never run the whirlpool system with all the jets
closed.
force of Air
Two knobs located on the bath serve as controls for the
air induction system. The intensity of the hydromassage
whirlpool action is determined by the amount of air inducted
into the water. As the amount of air is increased, the
hydromassage action increases. For maximum air induction,
rotate the control knobs fully counterclockwise to the largest
circles. For fewer air bubbles, decrease the amount of air
Small Multidirectional Jets
induction by rotating the control knob clockwise. When the
knobs are turned to the smallest circles, only water is being
circulated.
Page 18
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Purging the Whirlpool System
To remove accumulations of bathtub residue from the whirlpool system, it is recommended that a whirlpool bathtub be
cleaned regularly. For best results, however, we recommend that you clean your whirlpool bathtub after each use using,
Systems Clean™, our exclusive two-part plumbing system cleaner made specifically for whirlpool bathtubs. Systems
Clean™ is available through an authorized Jacuzzi Whirlpool Bath Distributor or by calling us direct at 1-800-288-4002.
Bathtub Additives
Do not use oil or oil-based bathtub additives.
If you want to use any kind of bathtub additive, use only a small amount of low-foaming powder or crystal substance;
the whirlpool action intensifies the foaming properties of soaps.
The use of certain bathtub oils, bubble baths, and bathtub additives may increase the level of accumulations of bathtub
residue in the whirlpool system and may cause false reading of the water level sensors. If excess accumulations
persist, you should discontinue use of these products.
maintenance
To clean your bathtub, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss
to a dulled acrylic surface by applying Meguiar’s #10 Mirror Glaze, a product specifically designed for use on acrylic
finishes. If Meguiar’s is not available, use a fine grade automotive rubbing compound followed by an application of
automotive paste wax.
Never use abrasive household cleaners on any Jacuzzi Luxury Bath product.
Surface Repair
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry
sandpaper. Restore the gloss using Meguiar’s Mirror Glaze or automotive paste wax. Major scratches and gouges
which penetrate the acrylic surface will require refinishing. Call Jacuzzi Luxury Bath to find a service agent in your area.
Suction Cover/Strainer maintenance
Clean the suction cover/strainer of hair and debris when
necessary.
Suction Fitting
Remove the center screw and detach the suction
cover.
1
Suction Cover
Clean the cover by backflushing debris from the holes.
Replace the suction cover immediately after cleaning.
2
3
Keep hair a minimum of 6 inches (152 mm) away
from the suction fitting at all times when the
whirlpool system is operating. Hair longer than
shoulder length should be secured close to the
head, or a bathing cap should be worn.
Do not operate the whirlpool system with the
suction cover/strainer broken, damamged or
removed!
Screw
It is a safety device and must always be in place on
the suction fitting to minimize the potential hazard
of hair and body entrapment.
Installation and Operation
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
REMEDY
Troubleshooting Procedures
PROBLEM
PROBABLE CAUSES
No power to pump/motor
Pump/motor not plugged in
Reset GFCI
Insert plug securely into outlet
Pump/motor does not start
Unsure that the tubing used to activate the pump/motor
is tightly secured to the bottom of the ON/OFF control
pad and to the AIR switch on back of the motor.
Pump/motor faulty
Jets are closed
Contact Jacuzzi Luxury Bath @ 800-288-4002
Open jets by rotating counter-clockwise
Pump/motor operates but not the multidirectional or
adjustable jets
Suction cover/strainer may be clogged
Air valves are closed
With the motor turned OFF, remove the suction cover/
strainer and remove any debris. Replace the suction
cover before operating
Pump/motor operates but air is not injected into the
water
Open air control valves
Water leakage from pump unions
Overtightened, O-ring may be pinched or improperly
seated, undertightened
Loosen unions , check and reseat O-ring. If O-ring has
been pinched out of shape, replace (refer to number
below). When tightening union nuts, handtighten only.
Pump/motor shuts off by itself before time elapses
Motor thermal protection has deactivated pump/motor
due to overheating (supply voltage low)
Let motor cool; thermal protection will reset. Check for
proper ventilation (check supply voltage)
GFCI tripped
Reset GFCI. If it continues to trip, do not use this unit.
Disconnect the unit and have the problem corrected by
a licensed electrician before using.
Inadequate supply wiring
Consult a licensed electrician to correct the wiring unit.
If the unit is within the warranty period, contact Jacuzzi Whirlpool Bath Service Support at 1-800-288-4002 with your bath’s serial number
before work is started. The serial number is located on the Specification/Serial Number Plate.
Page 20
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Technical Specifications
Specifications - Rectangular
(Right Hand and Left Hand)
L
W
L
(25.4 mm)
1"
W
2"
(Motor)
(Motor)
(51 mm)
H
H
SIDE VIEW
END VIEW
SIDE VIEW
END VIEW
BATHS WITHOUT INTEGRAL SKIRT, 6036, 6042, 7236, & 7242
BATHS WITH INTEGRAL SkIRT
L
W
2"
(Motor)
(Motor)
(51 mm)
H
A
SIDE VIEW
END VIEW
B
DRAIN/OVERFLOW
BATHS WITHOUT INTEGRAL SKIRT, 542BM & 6032
SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand
AVERAGE
OPERATING
FLOOR LOADING GALLONAGE
HEATER READY
FOR FIELD
INSTALLATION
DRAIN/OVERFLOW
DIMENSIONS
TOTAL WEIGHT/
PRODUCT
WEIGHT
SKIRT &
MOUNTING
MODEL
DIMENSIONS
(1524 mm) L
CUTOUT
60"
42"
20"
16-⅞"
(429 mm) A
(292 mm) B (1473 mm x 1016 mm)
58" x 40"
927 lb
(421 kg)/
54 lb/ft2
110 lb
(50 kg)
Available
60 Min U.S. gal
(227 liters)
68 Max U.S. gal
(257 liters)
ESPREE 542**
(1067 mm) W 11-½"
( 508 mm) H
BACK MASSAGE
DQ75000 HEATER KIT
DQ75000 HEATER KIT
(263 kg/m2)
LH
ESPREE 6032
60"
32"
22"
(1524 mm) L
( 813 mm) W 10-¼"
( 559 mm) H
18-116”
(459 mm) A
(273 mm) B
See
Page 23
785 lb
(357 kg)/
59 lb/ft2
50 Min U.S. gal
(189 liters)
58 Max U.S. gal
(220 liters)
102 lb
(46 kg)
Not
Available
LH
(288 kg/m2)
ESPREE 6032
WITH INTEGRAL
SKIRT
18-116"
10-¼"
(459 mm) A
(260 mm) B
NA
785 lb
(357 kg)/
59 lb/ft2
50 Min U.S. gal
(189 liters)
58 Max U.S. gal
(220 liters)
108 lb
(49 kg)
Integral
60"
32"
22"
(1524 mm) L*
DQ75000 HEATER KIT
( 813 mm) W
( 559 mm) H
(288 kg/m2)
LH & RH
ESPREE 6036
60"
36"
20"
(1524 mm) L
16-⅞"
(429 mm) A
(392 mm) B
58" x 34"
(1473 mm x 863 mm)
825 lb
(375 kg)/
55 lb/ft2
50 Min U.S. gal
(189 liters)
61 Max U.S. gal
(231 liters)
117 lb
(53 kg)
Not
Available
( 914 mm) W 15-7 16"
( 508 mm) H
DQ75000 HEATER KIT
DQ75000 HEATER KIT
LH
(268 kg/m2)
ESPREE 6042
LH
60"
42"
20"
(1524 mm) L
(1067 mm) W 11-¼"
( 508 mm) H
16-⅞"
(429 mm) A
(286 mm) B
58" x 40"
(1473 mm x 1016 mm)
927 lb
(421 kg)/
54 lb/ft2
60 Min U.S. gal
(227 liters)
68 Max U.S. gal
(257 liters)
110 lb
(50 kg)
Available
Integral
(263 kg/m2)
ESPREE 6042
WITH INTEGRAL
SKIRT
16-⅞"
(429 mm) A
(275 mm) B
NA
944 lb
(429 kg)/
55 lb/ft2
60 Min U.S. gal
(227 liters)
68 Max U.S. gal
(257 liters)
127 lb
(57 kg)
60"
42"
20"
(1524 mm) L*
10-13 16"
DQ75000 HEATER KIT
(1067 mm) W
( 508 mm) H
(268 kg/m2)
LH & RH
ESPREE 7236
72"
36"
20"
(1829 mm) L 16-⅞"
( 914 mm) W 15-⅝"
( 508 mm) H
(432 mm) A
(394 mm) B
70" X 34"
(1778 mm x 863 mm)
978 lb
(445 kg)/
54 lb/ft2
64 Min U.S. gal
(242 liters)
73 Max U.S. gal
(276 liters)
120 lb
(55 kg)
Not
Available
DQ75000 HEATER KIT
DQ75000 HEATER KIT
LH
(263 kg/m2)
ESPREE 7242
LH
72"
42"
20"
(1829 mm) L 16-⅞"
(1067 mm) W 15-⅝"
( 508 mm) H
(432 mm) A
(394 mm) B
70" X 40"
(1778 mm x 1016 mm)
1112 lb
(505 kg)/
53 lb/ft2
74 Min U.S. gal
(280 liters)
89 Max U.S. gal
(336 liters)
120 lb
(55 kg)
Not
Available
(258 kg/m2)
*Add ¼" (6 mm) to this dimension when roughing-in for 3-wall niche.
The overall dimensions are nominal with a tolerance of +0 and -¼” (6mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeatTM: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
**120 VAC, 20 AMP, 60 Hz. *120 VAC, 20 AMP, 60 Hz.
Installation and Operation
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Specifications - Corner
(Right Hand and Left Hand)
2"
H
(51 mm)
FRONT VIEW
SIDE VIEW
A
ESPREE 6060
B
1" (25.4 mm)
H
DRAIN/OVERFLOW
FRONT VIEW
SIDE VIEW
ESPREE 6060 WITH SKIRT
SPECIFICATIONS (Corner) LH = Left Hand, RH = Right Hand
HEATER READY
FOR FIELD INSTAL-
LATION
SKIRT &
MOUNTING
DRAIN/OVERFLOW
DIMENSIONS
TOTAL WEIGHT/ OPERATING
CUTOUT FLOOR LOADING GALLONAGE
PRODUCT
WEIGHT
DIMENSIONS
MODEL
ESPREE 6060
LH & RH
68 Min U.S. gal
Factory Installed
(S750000 HEATER KIT)
122 lb
(55 kg)
60"
60"
22"
(1524 mm) L
(1524 mm) L
( 559 mm) H
See
Page 23
971 lb
(441 kg)/
38.8 lb/ft2
(189 kg/m2)
18-½" (470 mm) A
12-¼" (311 mm) B
Not Available
(257 liters)
89 Max U.S. gal
(336 liters)
68 Min U.S. gal
(257 liters)
89 Max U.S.
gal
60"
(1524 mm) L
(1524 mm) L
( 559 mm) H
See
Page 23
122 lb
(55 kg)
ESPREE 6060
1264 lb
(575 kg)/
50 lb/ft2
18-½" (470 mm) A
12-¼" (311 mm) B
Integral
Factory Installed
(U395000 HEATER KIT)
WITH INTEGRAL 60"
SKIRT
22"
(244 kg/m2)
RH
(336 liters)
*Add ¼" (6 mm) to this dimension when roughing-in for 3-wall niche.
The overall dimensions are nominal with a tolerance of +0 and -¼” (6mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeatTM: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
**120 VAC, 20 AMP, 60 Hz. *120 VAC, 20 AMP, 60 Hz.
Page 22
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Roughing-In Reference
*60"
60"
21"
18"
18" x 4"
14'' x 4''
36"
42"
Motor
Motor
Opt. Service Access
2"
2"
15-7
"
Opt. Service Access
16
(Left hand only as shown)
(Left hand only)
ESPREE 6036
ESPREE 542 Bm
*60"
*60"
21"
14'' x 4''
16"
14- " x 4"
Motor
42"
Motor
32"
2"
Opt. Service Access
2"
Opt. Service Access
10-
"
(Left hand only)
(Left hand only as shown)
ESPREE 6032
ESPREE 6042
*60"
*60"
21"
14'' x 4''
16"
14" x 4"
Motor
42"
Motor
32"
2"
2"
10-13
"
16
ESPREE 6032 WITH SKIRT, LH
ESPREE 6042 WITH SKIRT, LH
*60"
*60"
21"
14'' x 4''
16"
Motor
Motor
42"
14" x 4"
32"
2"
ESPREE 6042 WITH SKIRT, RH
2"
10-13
"
16
ESPREE 6032 WITH SKIRT, RH
* The overall dimensions are nominal with a tolerance of +0 and -¼˝ (6mm).
fOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.
Installation and Operation
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Roughing-In Reference
*72"
72"
21"
18"
18" x 4"
18" x 4"
42"
36"
Motor
Motor
Opt. Service Access
Opt. Service Access
2"
2"
(Left hand only as shown)
(Left hand only as shown)
ESPREE 7236
ESPREE 7242
60"
Opt. Service
Access
Opt. Service
Access
60"
14" x 4"
8-15
15
Service
Access
Service
Access
"
16
16
Motor
Motor
3"
Opt. Service
Access
Opt. Service
Access
ESPREE 6060 WITHOUT SKIRT, LH
ESPREE 6060 WITHOUT SKIRT, RH
15
16
Motor
Junction Box
(Right hand only as shown)
ESPREE 6060 WITH INTEGRAL SKIRT
The overall dimensions are nominal with a tolerance of +0 and -¼˝ (6mm).
fOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
(Optional) RapidHeatTM: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.
Page 24
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Cut Outs
Drain
Drain
Motor
90ϒ
90ϒ
Overflow
Motor
90ϒ
90ϒ
Overflow
ESPREE 6060 WITHOUT SKIRT,
RIGHT HAND
ESPREE 6060 WITHOUT SKIRT,
LEFT HAND
58"
30"
4"
2"
DRAIN
ESPREE 6032 DROP-IN CUTOUT
Installation and Operation
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Espree™ Bathtub Series
Authorized Service
If you need a referral for a service company near you, or need assistance with operation or maintenance-related
for products, services, and an online copy of these Installation and Operation Instructions.
When requesting service or technical assistance please have available both the model and serial number of your
unit. This information can be obtained from the product registration card provided with your unit. If the card has been
misplaced, this information can be obtained from the specification/serial number label on the unit itself. The label is
located on the wall of the bathtub near the pump/motor.
SPECIfICATION/SERIAL NUmBER LABEL
Core Number,
Serial Number
xxxx-xxxxx
Applicable Electrical Specifications for your unit.
Electrical specifications printed in this area.
MODEL:
xxxxxxx
xxxxx
NAME:
COLOR:
MFG#:
SER#:
xxxxx
xxxxx
You will find your serial
number here
xxxxxx
Made in the USA
Appropriate Safety Compliance Logos for your unit.
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE TECHNICAL SPECIFICATIONS MANUAL SUPPLIED WITH PRODUCT.
Jacuzzi® Luxury Bath has obtained applicable code (standards) listings generally available on a national basis for products of this
type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product.
Jacuzzi® Luxury Bath makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi® Luxury Bath
14525 Monte Vista Avenue
Chino, California, 91710
1-800-288-4002
Page 26
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Lifetime Warranty on Jacuzzi Luxury Branded Baths for the Comfort, Comfort Plus,
Pure Air®, Luxury, Salon™ Spa, and Pure Air® II Collections
WARRANTy COvERAGE
Jacuzzi Luxury Bath (the “Company”) offers the following expressed limited lifetime warranty to the original purchaser of any Jacuzzi® Luxury Bath products provided
in the Company’s Comfort, Comfort Plus, Pure Air®, Pure Air® II, and Luxury™ collections ("Bath") who purchases the Bath for personal or single family residential use
(“User”): The Company will repair or replace, at its sole option, the Bath or its equipment in accordance with the following terms and conditions. This warranty does not
apply to non-branded Bath products manufactured by the Company.
LIfETImE WARRANTy ON BATHS
The Company extends to the User of the Bath a non-transferable limited lifetime warranty that the shell will maintain its structural integrity and configuration and be free
of water loss due to a defect in the bathtub shell. This warranty covers only the bathtub shell and the manufacturer installed pump, jets, controls, and blower against
defects in material or workmanship. This warranty does not apply to any display models or to any options or accessories which are covered under our limited ninety (90)
day warranty set forth below. Warranty coverage begins on the date the unit was originally purchased by the User and upon receipt by the Company of a completely
filled out Warranty Registration Card as described below.
2 yEAR LABOR WARRANTy fOR ALL fACTORy INSTALLED COmPONENTS
Our limited labor warranty is for a period of two (2) years from the date the unit was originally purchased by the User, but not more than Three (3) Years from date of
manufacture. All factory installed components (e.g., pump, motor, blower, and plumbing) are covered under our labor warranty against failure due to defects in materials
and workmanship.
NINETy DAy (PARTS ONLy) LImITED WARRANTy ON OPTIONS AND ACCESSORIES
Our limited warranty on options and accessories is for ninety (90) days for parts only. Our warranty covers options and accessories manufactured (e.g., drains fill
spout kits, trim kits, skirts, video monitors, plasma television screens, CD and MP3 players and other music and video devices and optional heaters) against defects
in material or workmanship. Warranty coverage begins on the date the option or accessory was originally purchased by the User. These items may be covered by a
manufacturer's warranty which may have a longer duration than this limited warranty. Please confirm with the manufacturer the duration of the appropriate warranty for
Options and Accessories.
WARRANTy LImITATIONS
Our limited warranty does not cover defects, damage, or failure caused by the common carrier, installer, user, or other persons, pets, or rodents, or resulting from,
without limitation, any of the following: careless handling (lifting unit by plumbing, abrading finish, etc.) including its own negligence; modification of any type for any
reason (including modification to meet local codes); improper installation (including installation not in accordance with instructions and specifications provided with
the unit); connections supplied by the installer of the equipment; improper voltage supply or unauthorized electrical modification; misuse; incorrect operation, or lack
of proper routine maintenance; operation of the unit without specified minimum amount of water or at inappropriate water temperature; use of abrasive or improper
cleaners; or acts of God, such as lightning, floods, earthquakes, etc.
In addition, THE COMPANY WILL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES or losses arising from any cause (e.g., water
damage to carpet, ceiling, tiles, marble, loss of use, etc.) including its own negligence; damages to, respecting, or resulting from: plated parts when pool and/or spa
chemicals are used in the unit or hard water conditions; optional bath equipment not manufactured by the Company but supplied by Dealer, installer or the Company;
the unit's prior usage as an operational display; or defects that should have been discovered before installation.
This limited warranty does not include: labor, transportation, or other costs incurred in the removal and/or reinstallation of the original unit and/or installation of a
replacement unit; any costs relating to obtaining access for repair; or loss of use damage, including loss of sales, profit or business advantage of any kind under any
circumstances. Bath units are excluded from any warranty coverage if any addition, deletion, or modification of any kind whatsoever has been made to the unit (or to
any component). Warranty coverage is provided in the United States of America and Canada only.
EXCLUSION Of ImPLIED WARRANTIES
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED ALTOGETHER OR TO THE FULLEST ExTENT
ALLOWED BY LAW.
NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable to Jacuzzi
Luxury Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not be responsible for any statements or
representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature or specifications furnished by the Company. Some
states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations and
exclusions may not apply to you.
®
Luxury Bath by Jacuzzi
U961000
®
Jacuzzi Luxury Bath
14525 Monte Vista Avenue
Chino, California 91710
Download from Www.Somanuals.com. All Manuals Search And Download.
RETURN Of WARRANTy REGISTRATION
To register your product, please go to our web-site Jacuzzi.com, click on Bath and Showers, then select ONLINE WARRANTY REGISTRATION from the top of the page.
You will then be prompted to enter your product Serial Number followed by your warranty registration information. Or you may also register by completing the registration
below and mailing it to Jacuzzi at the address provided below.
The attached Warranty Registration MUST be filled out by the purchaser within thirty (30) days from purchase and received by Jacuzzi Luxury Bath in order for this
warranty to become effective.
RESPONSIBILITIES Of OTHERS
Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the User. They are responsible for ensuring the unit
is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of a problem, the unit
must not be installed. The Company is not responsible for failures or damage that could have been discovered, repaired, or avoided by proper inspection and testing
(including proper water testing) prior to installation.
Damage occurring in transit is the responsibility of the carrier. The User or installer MUST open the crate and inspect the unit for damage when it is delivered. If damage is
discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure of the carrier to respond should be reported to the
seller and the carrier. Your freight claims should be filed promptly thereafter.
Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the responsibility of the
user.
Failure of any optional equipment is the sole responsibility of the equipment manufacturer except as provided above and shall not extend to or apply to any replacement
parts for the Options and Accessories. Any replacement parts shall be covered by the original equipment manufacturer.
The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or User of these requirements at the time of
purchase. The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state building codes in U.S.A. or municipal
or provincial codes in Canada.
WARRANTy SERvICE
For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs. Such firms are not agents or
representatives of the Company and cannot bind the Company by words or conduct.
The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered by the warranty;
the User has informed an Authorized Jacuzzi Luxury Bath Service Agent or Warranty Service Department Representative of the nature of the problem during the warranty
period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure occurred or was discovered within the
warranty period; an authorized independent service person or Company representative has been permitted to inspect the unit during regular business hours within a
reasonable time after the problem was reported by the User. In order to obtain warranty service, contact Jacuzzi Luxury Bath at:
jacuzzi.com
or
Warranty Service Department
14525 Monte Vista Avenue
Chino, California 91710
Call: 1-(800) 288-4002
To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied by the Company, call or write
the above. Provide a description of the problem and proof of purchase. You will be instructed how to obtain replacements and where to return, at your expense, the failed
component(s), option(s), or accessory(ies).
All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.
The Company's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the tender terminates the Company's
warranty obligation.
Download from Www.Somanuals.com. All Manuals Search And Download.
|