TRADITIONAL SERIES RACK CONVEYOR DISHMACHINE
TECHNICAL MANUAL
INSTALLATION MANUAL FOR EXPORT UNITS
SERVICE MANUAL FOR DOMESTIC UNITS
TS-44 SERIES
TSC-44 SERIES
TS-44
TS-44GP
TS-66
TSC-44
TSC-44GP
TSC-66
TS-66GP
TSC-66GP
Jackson MSC LLC.
P.O. Box 1060
Barbourville, KY. 40906
(606) 523-9795
Fax: (606) 523-9196
September 29, 2007
P/N 7610-002-98-29 (Revision C)
Download from Www.Somanuals.com. All Manuals Search And Download.
STOP!
PARE!
ARRET!
CALL 1-888-800-5672 TO REGISTER THIS PRODUCT!
FAILURE TO DO SO WILL VOID THE WARRANTY!
LLAME AL 1-888-800-5672 PARA REGISTRAR ESTE PRODUCTO!
AL NO HACERLO LA GARANTIA SERA ANULADA!
S.V.P. APPELER 1-888-800-5672 POUR ENREGISTRER CE PRODUIT,
LA GARANTIE SERA ANNULEE POUR TOUT PRODUIT NON- ENREGISTREE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
REVISION/ REVISION
MADE APPLICABLE
DETAILS
PAGE
DATE
BY
ECN
A
11-19-2004
MAW
7202
Initial release of manual.
7253, 7272 Added hose connections, curtain installation & detailed instruction
B
03-17-2005
MAW
6999
pages. Updated limit switch actuators. Added 600V models.
Added gas exhaust fan hookup schematic, updated electric
exhaust fan schematic. Added wash tank thermostat replacement
kit. Replaced rine drain weldment 5700-021-68-28 with 5700-002-
51-12. Added drain plumbing 5700-003-17-34. Added schematic
9905-003-16-50 for dual connection. Replaced vacuum breaker
4830-300-07-00 with 4820-003-06-13. Replaced plastic cap 4730-
003-12-00 with s/s cap 5700-011-67-11. Added the rinse fill motor
assembly. Added wash, rinse and psi decals. Changed the pre-
wash door weldments. Added service procedures. Corrected side
loader dimensions.
7600, 7571,
7558, 7679,
7660, 7383,
7361, 7463,
7367, 7462
C
02-15-2006
MAW
76
76
04-19-2007
09-29-2007
MAW
MAW
7898
N/A
Added 09905-003-32-20 fan load decal.
Removed alternate limit switches. Changed to centered layout.
Added warranty and repair centers listing pages. Removed ser-
vice procedures.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
NOMENCLATURE FOR THE MODELS COVERED IN THIS MANUAL
TS-44GP
TS = Traditional Series of rack conveyors
TSC = Traditional Series (water conserver) of rack conveyors
44 = 44” wide machine
66 = 66” wide machine
No suffix = Electrically heated, hot water sanitizing machine
GP = Gas heated, hot water sanitizing machine
Jackson MSC LLC. provides technical support for all
Model:
of the dishmachines detailed in this manual. We
strongly recommend that you refer to this manual
before making a call to our technical support staff.
Please have this manual with you when you call so
that our staff can refer you, if necessary, to the prop-
er page. Technical support is available from 8:00
a.m. to 5:00 p.m. (EST), Monday through Friday.
Technical support is not available on holidays.
Contact technical support toll free at 1-888-800-
5672. Please remember that technical support is
available for service personnel only.
Serial No.:
Installation Date:
Service Rep. Name:
Phone No.:
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SECTION
I.
DESCRIPTION
PAGE
SPECIFICATION INFORMATION
Operating Characteristics
2
Electrical Requirements TS-44/TSC-44
Electrical Requirements TS-66/TSC-66
TS-44/TSC-44 Dimensions
3
3
4
TS-66/TSC-66 Dimensions (Left to Right)
TS-66/TSC-66 Dimensions (Right to Left)
Dishtable Dimensions TS-44/TSC-44 & TS-66/TSC-66
Side Loader (Left to Right) Dimensions
Side Loader (Right to Left) Dimensions
Side Loader (Installed) Dimensions
Scrap Trough Dimensions
7
9
11
12
13
14
15
16
Typical Electric Booster Dimensions
II.
INSTALLATION & OPERATION INSTRUCTIONS
Installation Instructions
18
21
22
23
24
25
26
Deliming Operations
Curtain Installation Diagrams
Side Loader Installation & Operation Instructions
Dishmachine Operating Instructions
Detergent Control
Striker Plate Limit Switch Installation Instructions
III.
IV.
V.
PREVENTATIVE MAINTENANCE
TROUBLESHOOTING
28
30
PARTS SECTION
TS/TSC-44 Control Box Assembly
TS/TSC-66 Control Box Assembly
TS/TSC-44 Door & Hood Assembly
TS/TSC-66 Door & Hood Assembly
Heater Box Assembly
Gas Coil Assembly
Rinse Booster Tank Assembly
Recirculating Pump Assembly
Hose Connections
Prewash Incoming Plumbing Assembly
Incoming Rinse Plumbing Assembly
Incoming Rinse Plumbing Assembly (Gas Models)
1/2” Rinse Solenoid Valve & 1/2” Vacuum Breaker Repair Parts Kits
Frame Weldments/Dress Panels
TS/TSC-44 Drain Plumbing Assembly
TS/TSC-66 (Left to Right) Drain Plumbing Assembly
TS/TSC-66 (Right to Left) Drain Plumbing Assembly
TS/TSC-66 (Right to Left with Side Loader) Drain Plumbing Assembly
Drain Quench
Motor Assemblies
Pump Weldments
Prewash Arm/Manifold Assembly
Wash Arm/Manifold Assembly
Final Rinse Assembly
33
36
38
40
41
45
46
47
48
49
50
52
53
54
55
56
57
58
59
60
61
62
63
64
65
Pawl Bar Roller Bracket Kit
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Pawl Bar Assemblies
66
67
68
69
72
73
74
75
76
TS/TSC-44 Rack Rail Assembly
TS/TSC-66 Rack Rail Assemblies
Drive Assembly
Float Switch Components/Scrap Basket Assembly
Miscellaneous Parts & Weldments
Strainers
Curtains/Tub Magnets
Exhaust Fan Control Option/Table Limit Switches
Side Loader Section:
Loader Track Assemblies
Pawl Bar Assemblies
Pawl Bar Roller Bracket Assemby
Vent Cowl Option
77
78
79
80
81
Rinse Fill Option
VI.
ELECTRICAL SCHEMATICS
TS-44/TSC-44
208-230 Volts, 60 Hz, 1 Phase
208-230 Volts, 60 Hz, 3 Phase
460-600 Volts, 60 Hz, 3 Phase
460 Volts, 60 Hz, 3 Phase Dual Connection
TS-44GP/TSC-44
83
84
85
86
208-230 Volts, 60 Hz, 1 Phase
208-230 Volts, 60 Hz, 3 Phase
460 Volts, 60 Hz, 3 Phase
87
88
89
TS-66/TSC-66
208-230 Volts, 60 Hz, 1 Phase
208-230 Volts, 60 Hz, 3 Phase
460 Volts, 60 Hz, 3 Phase
90
91
92
TS-66GP/TSC-66GP
208-230 Volts, 60 Hz, 1 Phase
208-230 Volts, 60 Hz, 3 Phase
460-600 Volts, 60 Hz, 3 Phase
Conveyor Side Loader & Exhaust Fan Hook-Up Schematic
93
94
95
96
VII.
TROUBLESHOOTING
97
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1:
SPECIFICATION INFORMATION
1
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
OPERATING CHARACTERISTICS
RACKS PER HOUR:
WATER TEMPERATURES:
TS-44/TS-44GP
TSC-44/TS-44GP
TS-66/TS-66GP
TSC-66/TSC-66GP
252
119
252
119
TS-44/TS-44GP
WASH (MINIMUM)
RINSE (MINIMUM)
160°F
180°F
TSC-44/TSC-44GP
WASH (MINIMUM)
RINSE (MINIMUM)
DISHES OR GLASSES PER HOUR:
160°F
180°F
TS-44/TS-44GP
TSC-44/TS-44GP
TS-66/TS-66GP
TSC-66/TSC-66GP
6300
2975
6300
2975
TS-66/TS-66GP
PREWASH (RECOMMENDED)
WASH (MINIMUM)
110-140°F
160°F
RINSE (MINIMUM)
180°F
PREWASH TANK CAPACITY (GALLONS):
TSC-66/TSC-66GP
TS-66/TS-66GP
TSC-66/TSC-66GP
17.25
17.25
PREWASH ( RECOMMENDED)
WASH (MINIMUM)
110-140°F
160°F
RINSE (MINIMUM)
180°F
WASH TANK CAPACITY (GALLONS):
FLOW PRESSURE (PSI)
20±5
TS-44/TS-44GP
TSC-44/TS-44GP
TS-66/TS-66GP
TSC-66/TSC-66GP
20.4
20.4
20.4
20.4
FLOWRATE (GPM) TS SERIES
FLOWRATE (GPM) TSC SERIES
3.1
1.1
GAS SPECIFICATIONS:
WASH PUMP CAPACITY
Please refer to your gas booster manufacturer’s instructions.
GALLONS PER MINUTE (ALL MODELS):
VENTING REQUIREMENTS (CFM)(100% CAP.):
270
MOTOR ELECTRICAL CHARACTERISTICS:
DRIVE MOTOR HP
WASH MOTOR HP
POWER RINSE MOTOR HP
PREWASH MOTOR HP:
TS-66/TS-66GP
1/4
2
2
INPUT END
OUTPUT END
TOTAL
200
400
600
1
1
CONVEYOR SPEED (FPM):
TSC-66/TSC-66GP
TS-44/TS-44GP
TSC-44/TS-44GP
TS-66/TS-66GP
TSC-66/TSC-66GP
7.0
3.33
7.0
3.33
GALLONS PER RACK:
TS-44/TS-44GP
TSC-44/TS-44GP
TS-66/TS-66GP
TSC-66/TSC-66GP
0.74
0.55
0.74
0.55
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
ELECTRICAL REQUIREMENTS
NOTE: Typical Electrical Circuit is based upon (1) 125% of the full amperage load of the machine and (2) typical fixed-
trip circuit breaker sizes as listed in the NEC 2002 Edition. Local codes may require more stringent protection than
what is displayed here. Always verify with your electrical service contractor that your circuit protection is adequate
and meets all applicable national and local codes. These numbers are provided in this manual simply for reference
and may change without notice at any given time.
TS-44/TSC-44:
RINSE
TYPICAL
HEATER
RATING
TOTAL
AMPS
ELECTRICAL
CIRCUIT
VOLTS PH
HZ
208
230
208
230
460
600
1
1
3
3
3
3
60
60
60
60
60
60
N/A
N/A
N/A
N/A
N/A
N/A
83 Amps
76 Amps
49 Amps
45 Amps
23 Amps
19 Amps
110 Amp
100 Amp
70 Amp
60 Amp
30 Amp
25 Amp
TS-44GP/TSC-44GP:
RINSE
TYPICAL
HEATER
RATING
TOTAL
AMPS
ELECTRICAL
CIRCUIT
VOLTS PH
HZ
208
230
208
230
460
1
1
3
3
3
60
60
60
60
60
N/A
N/A
N/A
N/A
N/A
12 Amps
12 Amps
8 Amps
8 Amps
5 Amps
15 Amp
15 Amp
15 Amp
15 Amp
15 Amp
TS-66/TSC-66:
VOLTS PH
RINSE
HEATER
RATING
TYPICAL
ELECTRICAL
CIRCUIT
TOTAL
AMPS
HZ
208
230
208
230
460
600
1
1
3
3
3
3
60
60
60
60
60
60
N/A
N/A
N/A
N/A
N/A
N/A
89 Amps
82 Amps
52 Amps
48 Amps
24 Amps
22 Amps
125 Amp
110 Amp
70 Amp
60 Amp
30 Amp
30 Amp
TS-66GP/TSC-66GP:
RINSE
TYPICAL
HEATER
RATING
TOTAL
AMPS
ELECTRICAL
CIRCUIT
VOLTS PH
HZ
208
230
208
230
460
1
1
3
3
3
60
60
60
60
60
N/A
N/A
N/A
N/A
N/A
18 Amps
18 Amps
12 Amps
12 Amps
7 Amps
25 Amp
25 Amp
15 Amp
15 Amp
15 Amp
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
TS-44/TSC-44 DIMENSIONS
LEFT TO RIGHT MODEL SHOWN.
ON RIGHT TO LEFT MODELS, THE
INCOMING WATER CONNECTION
IS ON THE OPPOSITE END.
4-1/2"
6"
C
A
21"
25"
Add 3” to overall width
to take into account
the conduit on the
back of the machine.
44" TABLE TO TABLE
60"
D
B
8"
61-1/4”
E
5”
17"
62"
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
TS-44/TSC-44 DIMENSIONS (CONTINUED)
LEGEND FOR TS-44/TSC-44/TS-44GP/TSC-44GP DIMENSIONS:
A = 1/2” IPS incoming water connection, approximately 59-1/2” above the finished floor. Electric heat models only.
B = 1/2” IPS incoming water connection, approximately 59-1/2” above the finished floor. Gas heat models only.
C = Incoming electrical connection point, approximately 59-1/2” above the finished floor. Refer to machine data plate for elec-
trical requirements.
D = 1/2” IPS incoming water connection, approximately 59-1/2” above the finished floor. Gas heat models only, left to right con-
figuration.
E = 1-1/2” IPS drain point connection. If grease trap is required by code, size for 30 gallons per minute flowrate.
F = 1/2” IPS water outlet, approximately 6” above the finished floor. Gas heat models only.
11-1/2"
AUXILLARY
RINSE TANK
Typical dimension of the auxillary rinse tank found on the
gas-heated models.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
TS-44/TSC-44 DIMENSIONS (CONTINUED)
WALL
4”
HEIGHT WITH DOOR OPEN: 72"
NOTES CONCERNING THE TS-44/TSC-44 DIMENSIONS:
1. All dimensions are +/- 1/2” in the vertical due to adjustment of the bullet
feet.
2. A minimum of 4” spacing is required between the unit and the walls on all
sides.
3. The maximum recommended distance between the unit and any external
booster heater (electric or gas) is 20 feet.
4. Booster heaters have seperate electrical requirements from the machines.
5. Machine width as dimensioned does not include an approximate 3” for the
conduit that is attached to the back of the machine.
66"
1"
F
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
TS-66/TSC-66 (LEFT TO RIGHT) DIMENSIONS
A L W L
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
TS-66/TSC-66 (LEFT TO RIGHT) DIMENSIONS (CONTINUED)
LEGEND FOR TS-66/TSC-66 (LEFT TO RIGHT) DIMENSIONS:
A = Incoming electrical connection point, approximately 61-1/4” above the finished floor. Refer to machine data plate for elec-
trical requirements.
B = 1/2” IPS incoming water connection, approximately 61-1/4” above the finished floor. Electric heat models only.
C = 1/2” IPS prewash incoming water connection, approximately 61-1/4” above the finished floor. Electric heat models only.
D = 1-1/2” IPS drain point connection. If grease trap is required by code, size for 30 gallons per minute flowrate.
NOTES CONCERNING THE TS-66/TSC-66 DIMENSIONS:
1. All dimensions are +/- 1/2” in the vertical due to adjustment of the bullet feet.
2. A minimum of 4” spacing is required between the unit and the walls on all sides.
3. The maximum recommended distance between the unit and any external booster heater (electric, steam or gas) is 20 feet.
4. Booster heaters have seperate electrical requirements from the machines.
5. Machine width as dimensioned does not include an approximate 3” for the conduit that is attached to the back of the machine.
11-1/2"
AUXILLARY
RINSE TANK
Typical dimension of the auxillary rinse tank found on the
gas-heated models.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
TS-66/TSC-66 (RIGHT TO LEFT) DIMENSIONS
A L W L
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
TS-66/TSC-66 (RIGHT TO LEFT) DIMENSIONS
LEGEND FOR TS-66/TSC-66 (RIGHT TO LEFT) DIMENSIONS:
A = Incoming electrical connection point, approximately 61-1/4” above the finished floor. Refer to machine data plate for elec-
trical requirements.
B = 1/2” IPS incoming water connection, approximately 61-1/4” above the finished floor. Electric heat models only.
C = 1/2” IPS prewash incoming water connection, approximately 61-1/4” above the finished floor. Electric heat models only.
D = 1-1/2” IPS drain point connection. If grease trap is required by code, size for 30 gallons per minute flowrate.
NOTES CONCERNING THE TS-66/TSC-66 DIMENSIONS:
1. All dimensions are +/- 1/2” in the vertical due to adjustment of the bullet feet.
2. A minimum of 4” spacing is required between the unit and the walls on all sides.
3. The maximum recommended distance between the unit and any external booster heater (electric, steam or gas) is 20 feet.
4. Booster heaters have seperate electrical requirements from the machines.
5. Machine width as dimensioned does not include an approximate 3” for the conduit that is attached to the back of the machine.
11-1/2"
AUXILLARY
RINSE TANK
Typical dimension of the auxillary rinse tank found on the
gas-heated models.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
DISHTABLE DIMENSIONS
“C”
8”
TABLE TO TABLE
4” wide x 16” long vent
connection in splash shields.
Shipped with cover plate. If
required a vent collar & damper
is available at extra charge when
ordered. Typical both ends.
4”
“B”
“A”
PLAN VIEW
25”
2 1/8”
20 3/4”
Load & unload tables
to have identical
flange detail.
3/4”
TS/TSC-44 DIMENSIONS:
“A” = 60”
TS/TSC-66 DIMENSIONS:
“A” = 82”
“B” = 52”
“B” = 74”
“C” = 44”
“C” = 66”
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
SIDE LOADER (LEFT TO RIGHT) DIMENSIONS
1/2”
MINIMUM
DISHTABLE
NOTE: ALL DIMENSIONS ARE TYPICAL.
USE SILICONE
BETWEEN
TABLE AND LIP
OF SIDE
LOADER TO
PREVENT LEAK-
AGE.
WALL OF SIDE
LOADER
1/2”
25”
4 1/2”
MINIMUM
5”
DISHWASHER
SECTION “A-A”
12 1/2”
CENTER-LINE
DISHMACHINE
VENT CONNECTION
OPENING
CONVEYOR
DISHMACHINE
SPLASH SHIELD
A
A
1 1/2” DRAIN. CONNECTED
TO DISHMACHINE DRAIN
LINE
14 1/2”
29”
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
SIDE LOADER (RIGHT TO LEFT) DIMENSIONS
DISHTABLE
1/2”
MINIMUM
NOTE: ALL DIMENSIONS ARE TYPICAL.
USE SILICONE
WALL OF SIDE
LOADER
BETWEEN TABLE
AND LIP OF SIDE
LOADER TO PRE-
VENT LEAKAGE
1/2”
25”
4 1/2”
MINIMUM
5”
DISHWASHER
SECTION “A-A”
12 1/2”
CENTER LINE
DISHMACHINE
VENT CONNECTION
OPENING
CONVEYOR
DISHMACHINE
SPLASH
SHIELD
A
A
14 1/2”
1 1/2” DRAIN. CONNECTED TO
DISHMACHINE DRAIN LINE
29”
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
SIDE LOADER (INSTALLED) DIMENSIONS
23” SIDE LOADER DIMENSIONS
MODEL
TS/TSC 44”
TS/TSC 66”
DIMENSIONS
75”
97”
(Left to Right installation shown for reference.)
30” SIDE LOADER DIMENSIONS
MODEL
TS/TSC 44”
TS/TSC 66”
DIMENSIONS
82”
104”
NOTE: ALL DIMENSIONS ARE TYPICAL.
10”
4”
34”
23” or 30” depending on
the width of the side
loader.
Refer to chart above.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
SCRAP TROUGH DIMENSIONS
NOTE: DIMENSIONS ARE TYPICAL FOR BOTH ENDS.
SCRAP TROUGH
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SPECIFICATION INFORMATION
TYPICAL ELECTRIC AND GAS BOOSTER DIMENSIONS
Electric Booster Dimensions (Typical)
18”
30-1/2”
(
6”
24”
OUTLET
3/4" NPT
Coupling for
7-7/8”
1
3/4"
Temperature/Pressure
Relief Valve
18”
12”
(83 mm)
INLET
2”
Electical connection
from side or below
3/4" NPT Nipple
6”
SIDE VIEW
REAR VIEW
36”
20-3/4”
Alternate TPRV
Location
Electrical
Electrical
Water Outlet
Water Inlet
Gas Inlet
25-1/8”
Gas Water Water
Inlet Outlet Inlet
31-1/4”
6”
LEFT SIDE VIEW
Gas Booster Dimensions
(Typical)
Alternate
4" (102 mm)
Vent Adapter
TPRV
Flue
Location
Water Outlet
Water Inlet
Gas Inlet
Water Water Gas
Inlet Outlet Inlet
RIGHT SIDE VIEW
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2:
INSTALLATION & OPERATION
INSTRUCTIONS
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indi-
cator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away
the container. The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new, undam-
aged condition. However, rough handling by carriers or others may result in there being damage to the unit while in transit. If
such a situation occurs, do not return the unit to Jackson; instead, contact the carrier and ask them to send a representative to
the site to inspect the damage to the unit and to complete an inspection report. You must contact the carrier within 48 hours of
receiving the machine. Also, contact the dealer through which you purchased the unit.
UNPACKING THE DISHMACHINE: Once the machine has been removed from the container, ensure that there are no miss-
ing parts from the machine. This may not be obvious at first. If it is discovered that an item is missing, contact Jackson imme-
diately to have the missing item shipped to you.
LEVEL THE DISHMACHINE: The dishmachine is designed to operate while being level. This is
important to prevent any damage to the machine during operation and to ensure the best results
when washing ware. The unit comes with adjustable bullet feet, which can be turned using a pair of
channel locks or by hand if the unit can be raised safely. Ensure that the unit is level from side to side
and from front to back before making any connections.
Frame with Adjustable Foot
PLUMBING THE DISHMACHINE: All plumbing connections must comply with all applicable local, state, and national plumb-
ing codes. The plumber is responsible for ensuring that the incoming water line is thoroughly flushed prior to connecting it to
any component of the dishmachine. It is necessary to remove all foreign debris from the water line that may potentially get
trapped in the valves or cause an obstruction. Any valves that are fouled as a result of foreign matter left in the water line, and
any expenses resulting from this fouling, are not the responsibility of the manufacturer.
CONNECTING THE DRAIN LINE: The drain for the models covered in
this manual are gravity discharge drains. All piping from the machine to
Adjusting screw
the drain must be a minimum 1 1/2” NPT and shall not be reduced.
There must also be an air gap between the machine drain line and the
floor sink or drain. If a grease trap is required by code, it should have a
flow capacity of 30 gallons per minute.
Locking nut
WATER SUPPLY CONNECTION: Ensure that you have read the sec-
tion entitled “PLUMBING THE DISHMACHINE” above before proceed-
ing. Install the water supply line (1/2” pipe size minimum) to the dish-
machine line strainer using copper pipe. It is recommended that a water
shut-off valve be installed in the water line between the main supply and
the machine to allow access for service. The water supply line is to be
capable of 25 PSI “flow” pressure at the recommended temperature
indicated on the data plate.
Incoming Plumbing Connection
In areas where the water pressure fluctuates or is greater than the recommended pressure, it is suggested that a water pres-
sure regulator be installed. The models covered in this manual do come with water pressure regulators as standard equipment.
Please notify Jackson immediately if this component is not present on your machine.
Do not confuse static pressure with flow pressure. Static pressure is the line pressure in a “no flow” condition (all valves and
services are closed). Flow pressure is the pressure in the fill line when the fill valve is opened during the cycle.
It is also recommended that a shock absorber (not supplied) be installed in the incoming water line. This prevents line hammer
(hydraulic shock), induced by the solenoid valve as it operates, from causing damage to the equipment.
PLUMBING CHECK: Slowly turn on the water supply to the machine after the incoming fill line and the drain line have been
installed. Check for any leaks and repair as required. All leaks must be repaired prior to placing the machine in operation.
GAS CONNECTIONS: Some machines covered in this manual are designed to use gas as an outside source of heat for wash
tank water. The machines come with connections by which an outside source needs to be connected. Connect all incoming gas
lines in accordance with the gas booster manufacturer’s instructions. Ensure that all applicable codes and regulations are
adhered to.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS (CONTINUED)
ELECTRICAL POWER CONNECTION: Electrical and grounding connections must comply with the applicable portions of the
National Electrical Code ANSI/NFPA 70 (latest edition) and/or other electrical codes.
Disconnect electrical power supply and place a tag at the
disconnect switch to indicate that you are working on the
circuit.
The dishmachine data plate is located on the right side and to the
front of the machine. Refer to the data plate for machine operating
requirements, machine voltage, total amperage load and serial num-
ber.
To install the incoming power lines, open the control box. Install con-
duit into the pre-punched holes in the back of the control box. Route
power wires and connect to power block and grounding lug. Install
Incoming Power Connection
the service wires (L1, L2, and L3 (3 phase only)) to the appropriate
terminals as they are marked on the terminal block. Install the
grounding wire into the lug provided. Tighten the connections. It is
Terminal Block
recommended that “DE-OX” or another similar anti-oxidation agent
be used on all power connections.
Decal showing “L1”, “L2”, & “L3”
(3 phase models only).
VOLTAGE CHECK: Ensure that the power switch is in the OFF position and apply power to the dishmachine. Check the incom-
ing power at the terminal block and ensure it corresponds to the voltage listed on the data plate. If not, contact a qualified ser-
vice agency to examine the problem. Do not run the dishmachine if the voltage is too high or too low. Shut off the service break-
er and mark it as being for the dishmachine. Advise all proper personnel of any problems and of the location of the service
breaker. Replace the control box cover and tighten down the screws.
VENTILATION OF DISHMACHINE: The dishmachine should be located with provisions for venting into an adequate exhaust
hood or ventilation system. This is essential to permit efficient removal of the condensation exhaust. Ensure that the exhaust
system is acceptable in accordance with all applicable codes and standards.
NOTE: Any damage that is caused by steam or moisture due to improper ventilation is NOT covered under the
warranty.
This units covered in this manual have the following exhaust requirements:
Load End:
Unload End:
200 CFM
400 CFM
The exhaust system must be sized to handle this volume for the dishmachine to operate as it was designed to.
ELECTRIC HEAT: The thermostats for the machines covered in this manual are factory set. They should not be adjusted except
by an authorized service agent.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS (CONTINUED)
CHEMICAL FEEDER EQUIPMENT: Detergent may be introduced into the unit through the
removal of the bulkhead plug in the rear of the tub and replacing it with the third party detergent
injection fitting. Remove the bulkhead plug in the side of the tub to install the detergent concen-
tration probe.
For more information concerning detergent concerns, please refer to the page entitled “Detergent
Control”.
Detergent Connection Point
(Machine rear view)
Brass Plug
The 1/8” brass plugs on the incoming plumbing rinse injector may be removed to install
rinse aid injection fittings.
Brass Plug
Rear of Control Box
Rinse Injector
All wires for the chemical injectors should be routed through
one of the extra openings in the back of the control box.
Terminals in the control box marked “CVS” provide a
constant voltage signal whenever the drive motor is
operating.
Terminals in the control box marked “DET” provide a
voltage signal whenever the wash motor is operating.
Connection Points
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS
DELIMING OPERATIONS
DELIMING OPERATIONS: In order to maintain the dishmachine at its optimum performance level, it will be required to remove
lime and corrosion deposits on a frequent basis. A deliming solution should be available from your detergent supplier. Read and
follow all instructions on the label of the deliming solution.
To proceed with the deliming operation, fill the dishmachine and add the correct amount of deliming solution as recommended
by the deliming solution manufacturer. The water capacity of the various tanks of the dishmachine can be verified on the spec-
ification sheet(s) of this manual.
Perform the following operations to delime the dishmachine:
1. Turn the NORMAL/DELIME switch on the back of the control box to the DELIME position.
2. Disconnect or turn off all chemical feeder pumps.
3. Close all doors (after adding the deliming solution).
4. Run the machine for the recommended period of time.
Delime Switch
5. Turn the unit off and open the doors.
6. Wait five minutes, then inspect the inside of the machine. If the machine is not delimed, run another time cycle as per the
deliming solution’s instructions.
7. When clean, drain and re-fill the machine.
8. Run in MANUAL for 10 minutes to remove residual deliming solution.
9. Drain and re-fill the machine.
This equipment is not recommend for use with deionized water or other aggressive fluids. Use of deionized water or
other aggressive fluids will result in corrosion and failure of materials and components. Use of deionized water or
other aggressive fluids will void the manufacturer's warranty.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS
CURTAIN INSTALLATION DIAGRAMS
Please refer to the chart for
placement of the curtains.
TS SERIES MACHINES
44
L
19"
S
12"
L
21"
L
19"
S
12"
L
R
66
L
19"
S
12"
S
12"
L
19"
L
19"
S
12"
L
R
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS
SIDE LOADER INSTALLATION & OPERATION INSTRUCTIONS
This accessory assists in the delivery of a full dish rack from the break down (scrapping) table to the dishmachine. It will con-
vert the direction of travel 90°. Since the Side Loader is shipped mounted on the conveyor dishwasher there is no additional
installation required for this option. As it is operated mechanically by the dishwasher it does not require any plumbing or elec-
trical connections.
This Side Loader does not require or add any additional electrical or mechanical devices to the unit which could create opera-
tional or maintenance problems. As designed the drive mechanism is powered by the conveyor drive motor on the dishma-
chine. An extension on the pawl bar provides the drive to push the racks into the unit.
PREPARATION: Before proceeding with the start-up of the unit, verify that the Side Loader pan strainer is installed.
WARE PREPARATION: Proper preparation of ware will help ensure good results and less re-washes. If not done properly, ware
may not come out clean and the efficiency of the dishmachine will be reduced. It is important to remember that a dishmachine
is not a garbage disposal and that simply throwing unscraped dishes into the machine simply defeats the purpose altogether
of washing the ware. Scraps should be removed from ware prior to being loaded into a rack. Pre-rinsing and pre-soaking are
good ideas, especially for silverware and casserole dishes. Place cups and glasses upside down in racks so that they do not
hold water during the cycle. The dishmachine is meant not only to clean, but to sanitize as well, to destroy all of the bacteria
that could be harmful to human beings. In order to do this, ware must be properly prepared prior to being placed in the machine.
WASHING A RACK OF WARE: Once a rack is fully loaded it should be positioned against the front of the dish table. The rack
should then be moved into the Side Loader until it activates the actuator switch. Once the the machine is started, it should pull
the rack through the machine and push it out the unload end. Once a rack has started through, you may put another rack in.
OPERATIONAL INSPECTION: Based upon usage, the pan strainer may become clogged with soil and debris as the workday
progresses. Operators should regularly inspect the pan strainer to ensure it has not become clogged. If the strainer does
become clogged, it will reduce the washing capability of the machine. Instruct operators to clean out the pan strainer at regu-
lar intervals or as required by work load.
SHUTDOWN AND CLEANING: At the end of the workday, remove the pan strainer and clean as required. Wipe out the inside
of the Side Loader and then reinsert the strainer.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INSTALLATION & OPERATION INSTRUCTIONS
DISHMACHINE OPERATING INSTRUCTIONS
PREPARATION: Before proceeding with the start-up of the unit, verify the following:
1. Close door(s) on dishmachine.
2. Close the drain valve(s).
POWER UP: To energize the unit, turn on the power at the service breaker. The voltage should have been previously verified
as being correct. If not, the voltage will have to be verified.
FILLING THE WASH TUB: Ensure that the delime switch is in the NORMAL position, and place the power switch into the ON
position. The machine should fill automatically and shut off when the appropriate level is reached (just below the pan strainer).
The wash tub must be completely filled before operating the wash pump to prevent damage to the component. Once the wash
tub is filled, the unit is ready for operation.
Machines equipped with prewash sections should not be run without water in those sections. This can cause
damage to components.
WARE PREPARATION: Proper preparation of ware will help ensure good results and less re-washes. If not done properly, ware
may not come out clean and the efficiency of the dishmachine will be reduced. It is important to remember that a dishmachine
is not a garbage disposal and that simply throwing unscraped dishes into the machine simply defeats the purpose altogether
of washing the ware. Scraps should be removed from ware prior to being loaded into a rack. Pre-rinsing and pre-soaking are
good ideas, especially for silverware and casserole dishes. Place cups and glasses upside down in racks so that they do not
hold water during the cycle. The dishmachine is meant not only to clean, but to sanitize as well, to destroy all of the bacteria
hat could be harmful to human beings. In order to do this, ware must be properly prepared prior to being placed in the machine.
DAILY MACHINE PREPARATION: Refer to the section entitled “PREPARATION” at the top of this page and follow the instruc-
tions there. Afterwards, check that all of the chemical levels are correct and/or that there is plenty of detergent available for the
expected workload.
WASHING A RACK OF WARE: To wash a rack, simply slide a rack of soiled ware into the load end of the machine. Once the
the machine is started, it should pull the rack through the machine and push it out the unload end. Once a rack has started
through, you may put another rack in.
OPERATIONAL INSPECTION: Based upon usage, the pan strainers may become clogged with soil and debris as the work-
day progresses. Operators should regularly inspect the pan strainers to ensure they have not become clogged. If the strainers
do, they will reduce the washing capability of the machine. Instruct operators to clean out the pan strainers at regular intervals
or as required by work load.
NOTE: On units equipped with prewash sections operators should also take the time to inspect the prewash section
strainers and clean them as required by workload.
SHUTDOWN AND CLEANING: At the end of the workday, place the power switch in the OFF position and open the door(s).
Open the drain valves and allow the machine to drain completely. Remove the pawl bar assembly (clean as required). Remove
the pan strainers and, if equipped, the prewash strainers, run off sheets and scrap basket strainer. Remove the wash and, if
equipped, the prewash arms and verify that the nozzles and arms are free from obstructions. Flush the arms with fresh water.
Remove the pump suction strainers and clean out as required. Remove the rinse tray assembly and clean. Remove the cur-
tains and scrub with a mild detergent and warm water. Wipe out the inside of the unit and then reassemble with the compo-
nents previously removed.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INSTALLATION & OPERATION INSTRUCTIONS
DETERGENT CONTROL
Detergent usage and water hardness are two factors that contribute greatly to how efficiently your dishmachine will operate.
Using detergent in the proper amount can become, in time, a source of substantial savings. A qualified water treatment spe-
cialist can tell you what is needed for maximum efficiency from your detergent, but you should still know some basics so you’ll
understand what they are talking about.
First, you must understand that hard water greatly effects the performance of the dishmachine. Water hardness is the amount
of dissolved calcium and magnesium in the water supply. The more dissolved solids in the water, the greater the water hard-
ness. Hard water works against detergent, thereby causing the amount of detergent required for washing to increase. As you
use more detergent, your costs for operating the dishmachine will increase and the results will decrease. The solids in hard
water also may build-up as a scale on wash and rinse heaters, decreasing their ability to heat water. Water temperature is
important in removing soil and sanitizing dishes. If the water cannot get hot enough, your results may not be satisfactory. This
is why Jackson recommends that if you have installed the machine in an area with hard water, that you also install some type
of water treatment equipment to help remove the dissolved solids from the water before it gets to the dishmachine.
Second, hard water may have you adding drying agents to your operating cycle to prevent spotting, when the real problem is
deposited solids on your ware. As the water evaporates off of the ware, the solids will be left behind to form the spotting and
no amount of drying agent will prevent this. Again, using treated water will undoubtedly reduce the occurrences of this prob-
lem.
Third, treated water may not be suitable for use in other areas of your operation. For instance, coffee made with soft water may
have an acid or bitter flavor. It may only be feasible to install a small treatment unit for the water going into the dishmachine
itself. Discuss this option with your qualified water treatment specialist.
Even after the water hardness problems have been solved, there still must be proper training of dishmachine operators in how
much detergent is to be used per cycle. Talk with your water treatment specialist and detergent vendor and come up with a
complete training program for operators. Using too much detergent has as detrimental effects as using too little. The proper
amount of detergent must be used for job. It is important to remember that certain menu items may require extra detergent by
their nature and personnel need to be made aware of this. Experience in using the dishmachine under a variety of conditions,
along with good training in the operation of the machine, can go a long way in ensuring your dishmachine operates as effi-
ciently as possible.
Certain dishmachine models require that chemicals be provided for proper operation and sanitization. Some models even
require the installation of third-party chemical feeders to introduce those chemicals to the machine. Jackson does not recom-
mend or endorse any brand name of chemicals or chemical dispensing equipment. Contact your local chemical distributor for
questions concerning these subjects.
Some dishmachines come equipped with integral solid detergent dispensers. These dispensers are designed to accommodate
detergents in a certain sized container. If you have such a unit, remember to explain this to your chemical distributor upon first
contacting them.
As explained before, water temperature is an important factor in ensuring that your dishmachine functions properly. The data
plate located on each unit details what the minimum temperatures must be for either the incoming water supply, the wash tank
and the rinse tank, depending on what model of dishmachine you have installed. These temperatures may also be followed by
temperatures that Jackson recommends to ensure the highest performance from you dishmachine. However, if the minimum
requirements are not met, the chances are your dishes will not be clean or sanitized. Remember, a dish can look clean, but it
may not be sanitized. Instruct your dishmachine operators to observe the required temperatures and to report when they fall
below the minimum allowed. A loss of temperature can indicate a much larger problem such as a failed heater or it could also
indicate that the hot water heater for your operation is not up to capacity and a larger one may need to be installed.
There are several factors to consider when installing your dishmachine to ensure that you get the best possible results from it
and that it operates at peak efficiency for many years. Discuss your concerns with your local chemical distributor and water
treatment specialist before there is a problem.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INSTALLATION & OPERATION INSTRUCTIONS
STRIKER PLATE LIMIT SWITCH INSTALLTION INSTRUCTIONS
Installation Instructions:
1. Wiring: The switch is wired common and nor-
mally open because of the hinge design. By
interupting the line in series with the door
switches, the dishmachine ceases to operate.
Refer to the machine schematic for details on
how to wire the switch.
1/3 RACK WIDTH
INSTALL AT FAR END OF TABLE
2. Parts of the table switch are mounted in the
dishtable, at the end of the table and under the
table. See the drawing(s) for the relationship of
the switch to the table.
3. Move the limit switch as far down on the two
slots as possible and see that the limit switch is
straight on the base plate. This might require
adjustment of the nut on the connector for the
limit switch.
4. Then adjust the inside and the outside con-
nector nuts for the connector box so that it lines
up even with the limit switch and the base plate.
5. Tighten down the nuts for the seal so that
they are tight.
6. If you have any difficulty you might have to adjust the
connectors to the seal, screwing in or screwing out
until the installation is straight on the table and the limit
switch is actuated correctly by the rack.
TABLE LIMIT SWITCH THROUGH ROD HOLES
TABLE
SWITCH RODS
STRIKE PLATE
STRIKE PLATE BOLTS
3.00
2.00
MOUNTING BOLTS
TABLE BOTTOM
Ø0.75
1.875
Ø0.25
1.50
Unless noted, all dimensions are in
inches.
TABLE BOTTOM
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3:
PREVENTATIVE MAINTENANCE
27
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: PREVENTATIVE MAINTENANCE
PREVENTATIVE MAINTENANCE
The dishmachines covered in this manual are designed to operate with a minimum of interaction with the operator. However,
this does not mean that some items will not wear out in time. Jackson highly recommends that any maintenance and repairs
not specifically discussed in this manual should be performed by QUALIFIED SERVICE PERSONNEL ONLY. Performing main-
tenance on your dishmachine may void your warranty if it is still in effect, so if you have a question or concern, do not hesitate
to contact Jackson.
There are many things that operators can do to prevent catastrophic damage to the dishmachine. One of the major causes of
component failure has to do with prescrapping procedures. A dishmachine is not a garbage disposal; any large pieces of mate-
rial that are put into the machine shall remain in the machine until they are either broken up (after spreading out on your ware!)
or physically removed. Strainers are installed to help catch debris, but they do no good if they are clogged. Have operators reg-
ularly inspect the pan strainers to ensure (1) that they are free of soil and debris and (2) they are laying flat in the tub.
When cleaning out strainers, do NOT beat them on waste cans. The strainers are made of metal and can be forgiving; but once
severe damage is done, it is next to impossible for the strainer to work in the way it was designed to. Wipe out strainers with
a rag and rinse under a faucet if necessary. For stubborn debris, a toothpick should be able to dislodge any obstructions from
the perforations. Always ensure that strainers are placed back in the machine before operation and that they lay flat in the tub.
You may wish to also refer to the page entitled “Detergent Control” in order to learn more about how your water hardness will
effect the performance of your machine. Hard water makes dishmachines work harder and decreases efficiency.
Again, it is important to remind operators that trying to perform corrective maintenance on the dishmachine could lead to larg-
er problems or even cause harm to the operator. If a problem is discovered; secure the dishmachine using proper shut down
procedures as listed in this manual and contact Jackson.
Some problems, however, may having nothing to do with the machine itself and no amount of preventative maintanence is
going to help. A common problem has to do with temperatures being too low. Verify that the water temperatures coming to your
dishmachine match the requirements listed on the machine data plate. There can be a variety of reasons why your water tem-
perature could be too low and you should discuss it with Jackson to determine what can be done.
By following the operating and cleaning instructions in this manual, you should get the most efficient results from your machine.
As a reminder, here are some steps to take to ensure that you are using the dishmachine the way it was designed to work:
1. Ensure that the water temperatures match those listed on the machine data plate.
2. Ensure that all strainers are in place before operating the machine.
3. Ensure that all wash and/or rinse arms are secure in the machine before operating.
4. Ensure that drains are closed/sealed before operating.
5. Remove as much soil from dishes by hand as possible before loading into racks.
6. Do not overfill racks.
7. Ensure that glasses are placed upside down in the rack.
8. Ensure that all chemicals being injected to machine have been verified as being at the correct concentrations.
9. Clean out the machine at the end of every workday as per the instructions in the manual.
10. Always contact Jackson whenever a serious problem arises.
11. Follow all safety procedures, whether listed in this manual or put forth by local, state or national codes/regulations.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4:
TROUBLESHOOTING
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: TROUBLESHOOTING
COMMON PROBLEMS
WARNING: Inspection, testing and repair of electrical equipment should only be performed by a qualified ser-
vice technician. Many of the tests require that the unit have power to it and live electrical components be
exposed. USE EXTREME CAUTION WHEN TESTING THE MACHINE.
Problem: Nothing on dishmachine operates. The power switch is ON and the power indicator light is OFF.
1. Machine is not wired correctly to incoming power source. Have an electrician verify wiring.
2. Machine circuit breaker is tripped. Reset the circuit breaker. If it trips again, contact an electrician to verify the machine amp
draw.
3. Service breaker is tripped. Reset the service breaker. If it trips again, contact an electrician to verify the machine amp draw.
Problem: Machine will not fill. The power switch is ON and the power indicator light is ON.
1. No water supply to machine. Verify that water lines have been connected to the machine.
2. Dishmachine doors are not closed. Close doors completely.
3. Incoming water solenoid valve damaged/faulty. Verify that the valve is operating. If not, replace.
4. Tank floats faulty. Verify the wiring of the floats. Verify that no debris is jamming the floats. Replace if necessary.
Problem: Machine fills, but fill is weak.
1. Low incoming water pressure. Verify that incoming water pressure during fill is 20 ±5 PSI.
2. Incoming water solenoid is clogged. Verify that debris is not entrapped in valve. If so, remove debris.
Problem: Low wash tank temperature.
1. Low incoming water temperature. Verify that the incoming water temperature matches what is indicated on the machine data
plate.
2. Heater not energizing. Verify that the wash tank heater is operating. If not, replace.
3. Low incoming voltage. Have an electrician verify that the power coming to the machine is the same as indicated on the data
plate.
Problem: Low wash arm pressure, poor spray pattern.
1. Clogged wash arm nozzles. Verify that nozzles are not clogged with debris. If so, remove debris.
2. Clogged wash tank or wash pump strainers. Clean out strainers if necessary.
3. Worn wash pump impeller. Verify status of impeller, replace if necessary.
Problem: Low prewash arm pressure, poor spray pattern.
1. Clogged prewash arm nozzles. Verify that nozzles are not clogged with debris. If so, remove debris.
2. Clogged prewash tank or prewash pump strainers. Clean out strainers if necessary.
3. Worn prewash pump impeller. Verify status of impeller, replace if necessary.
Problem: Inadequate rinse.
1. Low incoming water pressure. Verify that incoming water pressure during fill is 20 ±5 PSI.
2. Incoming water solenoid is clogged. Verify that debris is not entrapped in valve. If so, remove debris.
Problem: Pawl bar does not move.
1. Failed or broken overload spring. Replace spring if necessary.
2. No power to the drive motor/failed drive motor. Verify power and wiring connections to the motor. If necessary, replace the
motor.
3. Pawl bar not properly installed. Verify that the pawl bar is installed correctly.
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: TROUBLESHOOTING
COMMON PROBLEMS
Problem: Racks go through the machine, but results are poor.
1. Verify that detergent is being dispensed into the machine at the appropriate quantities for the water volume. If not, get deter-
gent to appropriate level and review results of washing ware.
2. Clogged strainers/scrap basket. Clean out strainers and scrap basket and replace.
3. Ware not being properly prescrapped. Review paragraph entitled ‘Ware Preparation” in Operating Instructions.
4. Wash or rinse arms missing end plugs or caps. Verify and replace as required.
5. Low tank heat.
6. Inadequate rinse.
7. Incorrect voltage coming to the machine. Verify that the voltage matches that on the machine data plate.
8. Wash pump cavitation due to low water level. Verify that the drains are shut and that the water level is correct.
Problem: Spotting of silverware, glasses and dishes.
1. Incorrect final rinse temperature. Verify that the rinse water temperature matches that which is listed on the machine data
plate.
2. Clogged wash and/or rinse nozzles and arms. Remove the arms and verify that they and their nozzles are from debris.
3. Excessively hard water. Install a water softener to reduce hardness.
4. Loss of water pressure due to clogged/obstructed wash pump. Turn the power off to the machine at the source. Drain the
wash tank of water and verify that the pump intake is free from debris.
5. Improper scrapping procedures. Review the paragraph entitled “Ware Preparation” in Operating Instructions.
6. incorrect detergent/chemcial concentrations. Verify that the detergent/chemical concentrations are correct for the associat-
ed water volume.
TORQUE SETTINGS
When replacing components either in the control box or the heater box area, the manufacturer has suggestions on how much
to torque the screws and nuts used in securing items to the machine. Refer to the table below for the torque specifictions:
ITEMS
TORQUE SPEC
Relays
16 In/lbs
35 In/lbs
16 In/lbs
50 In/lbs
Heater Contactor
Heater Nuts
Terminal Block
TS Series Conveyors Technical Manual 7610-002-98-29
Issued: 02-15-2006 Revised: N/A
31
Download from Www.Somanuals.com. All Manuals Search And Download.
|