JVC Stereo System CA MXGT91R User Manual

COMPACT COMPONENT SYSTEM

CA-MXGT91R

CA-MXG71R

CA-MXGT91R

CA-MXG71R

STANDBY/ON

PLAY

EXCHANGE

PLAY

EXCHANGE

STANDBY

CD-R

RW PLAYBACK

CD-R/RW PLAYBACK

MX-GT91R

MX-G71R

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial

No. which are located either on the rear,

bottom or side of the cabinet. Retain this

information for future reference.

Model No.

Serial No.

GVT0052-008A

[B]

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY INSTRUCTIONS

“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment,

care must be taken if you are to obtain the best results and safety is to be assured.

✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮

Do read the operating instructions before you attempt to use the equipment.

Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment)

are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or

changing connections.

Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

Do be careful with glass panels or doors on equipment.

✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way — switch

off, withdraw the mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation

or has a standby mode.

Switch off using the switch on the equipment and make sure that your family know how to do this.

Special arrangements may need to be made for infirm or handicapped people.

DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is

illegal to watch television whilst driving.

DON’T listen to headphones at high volume as such use can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.

Overheating will cause damage and shorten the life of the equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s

approved stand or legs with the fixings provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case — this could result

in a fatal electrical shock.

— NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!

– G-2 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

We would like to thank you for purchasing one of our JVC products.

Before operating this unit, read this manual carefully and thoroughly to

obtain the best possible performance from your unit, and retain this manual

for future reference.

Power sources

• When unplugging from the wall outlet, always pull the

plug, not the AC power cord.

About This Manual

This manual is organized as follows:

• The manual mainly explains operations using the

buttons and controls on the unit. You can also use the

buttons on the remote control if they have the same or

similar names (or marks) as those on the unit.

If operation using the remote control is different from

that using the unit, it is then explained.

• Basic and common information that is the same for many

functions is grouped in one place, and is not repeated in

each procedure. For instance, we do not repeat the

information about turning on/off the unit, setting the

volume, changing the sound effects, and others, which are

explained in the section “Common Operations” on pages 9

to 11.

DO NOT handle the AC power cord with wet

hands.

Moisture condensation

Moisture may condense on the lens inside the unit in the

following cases:

• After starting heating in the room

• In a damp room

• If the unit is brought directly from a cold to a warm place

Should this occur, the unit may malfunction. In this case,

leave the unit turned on for a few hours until the moisture

evaporates, unplug the AC power cord, and then plug it in

again.

• The following marks are used in this manual:

Gives you warnings and cautions to prevent

from damage or risk of fire/electric shock.

Also gives you information which is not good

for obtaining the best possible performance

from the unit.

Others

• Should any metallic object or liquid fall into the unit,

unplug the unit and consult your dealer before operating

any further.

• If you are not going to operate the unit for an extended

period of time, unplug the AC power cord from the wall

outlet.

Gives you information and hints you had better

know.

DO NOT disassemble the unit since there are no

user serviceable parts inside.

Precautions

If anything goes wrong, unplug the AC power cord and

consult your dealer.

Installation

• Install in a place which is level, dry and neither too hot nor

too cold — between 5˚C (41˚F) and 35˚C (95˚F).

• Install the unit in a location with adequate ventilation to

prevent internal heat buildup in the unit.

• Leave sufficient distance between the unit and the TV.

• Keep the speakers away from the TV to avoid interference

with TV.

DO NOT install the unit in a location near heat

sources, or in a place subject to direct sunlight,

excessive dust or vibration.

– 1 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Location of the Buttons and Controls ....................... 3 Playing Back CDs (CD/CD-R/CD-RW) .................. 15

Front Panel ................................................................. 3

Remote Control .......................................................... 5

Loading CDs ............................................................ 15

Playing Back the Entire Discs

— Continuous Play............................................. 16

Basic CD Operations ................................................ 16

Programming the Playing Order of the Tracks

— Program Play ................................................. 17

Playing at Random — Random Play ....................... 18

Repeating Tracks or CDs — Repeat Play ................ 18

Prohibiting Disc Ejection — Tray Lock................... 18

Getting Started............................................................ 6

Supplied Accessories.................................................. 6

Putting the Batteries into the Remote Control ........... 6

Connecting Antennas ................................................. 6

Connecting Speakers .................................................. 7

Connecting Other Equipment..................................... 8

Canceling the Display Demonstration ....................... 8

Playing Back Tapes ................................................... 19

Common Operations .................................................. 9

Playing Back a Tape ................................................. 19

Locating the Beginning of a Song — Music Scan ... 19

Turning On or Off the Power ....................................... 9

Saving the Power Consumption While on Standby

— Ecology Mode ................................................. 9

Setting the Clock ........................................................ 9

Selecting the Sources................................................. 10

Adjusting the Volume ............................................... 10

Reinforcing the Bass Sound ..................................... 10

Selecting the Sound Modes ...................................... 10

Creating Your Own Sound Mode

Recording .................................................................. 20

Recording a Tape on Deck B.................................... 20

Dubbing Tapes.......................................................... 21

CD Direct Recording ................................................. 21

Auto Edit Recording.................................................. 22

Using the Timers ....................................................... 23

Using Daily Timer .................................................... 23

Using Recording Timer ............................................ 25

Using Sleep Timer .................................................... 26

Timer Priority ........................................................... 26

— Manual Mode................................................. 11

Listening to FM and AM (MW/LW) Broadcasts ... 12

Tuning in a Station ................................................... 12

Presetting Stations .................................................... 12

Tuning in a Preset Station ........................................ 12

Additional Information ............................................ 27

Troubleshooting ........................................................ 28

Maintenance .............................................................. 29

Specifications............................................................. 30

Receiving FM Stations with RDS ............................ 13

Changing the RDS Information ............................... 13

Searching for Programs by PTY Codes

(PTY Search) ...................................................... 13

Switching to a Program Type

of Your Choice Temporarily .............................. 14

– 2 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Location of the Buttons and Controls

Become familiar with the buttons and controls on your unit.

Front Panel

STANDBY/ON

PLAY

EXCHANGE

STANDBY

;

CD-R/RW PLAYBACK

– 3 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Continued

Display Window

See pages in the parentheses for details.

a 0 (Disc tray open/close) (CD1, CD2, and CD3) buttons

(15, 16, 18)

Pressing one of these buttons also turns on the unit.

s CANCEL/DEMO button (8, 9, 17, 19, 22 – 26)

d SOUND MODE control (10)

f SUBWOOFER LEVEL + / – control (10)

g TUNING + / – buttons (12)

Front Panel

1 Disc trays

2 STANDBY/ON

(9, 24, 25)

3 Remote sensor

4 ECO button (9)

button and STANDBY lamp

1 / ¡ (fast left/fast right) buttons (11, 16, 19)

h VOLUME + / – control (10)

5 PRESET + / – control (12)

j 7 (stop) button (16 – 22, 25)

k Tape operation buttons

4 / ¢ (reverse search/forward search) control

(9, 11, 16 – 18, 22 – 25)

• TAPE A/B button (19)

6 Display window

• REVERSE MODE button (19, 21, 22)

• REC START/STOP button (20 – 22, 25)

l DUBBING button (21)

/ Deck B cassette holder (19 – 22, 25)

z EJECT 0 button for deck B (19, 20)

7 TAPE 2 3 button and lamp (9, 19 – 21)

Pressing this button also turns on the unit.

8 CD 3¥8 (play/pause) button and lamp (9, 16 – 18, 22)

Pressing this button also turns on the unit.

9 FM/AM button and lamp (9, 12)

Pressing this button also turns on the unit.

p AUX button and lamp (9)

Display Window

1 Timer indicators

Pressing this button also turns on the unit.

q CD play mode buttons

•

(Timer), DAILY (Daily Timer), REC (Recording

Timer), and SLEEP (Sleep Timer) indicators

• REPEAT button (18)

• PROGRAM button (17)

2 Tape operation indicators

• RANDOM button (18)

w CLOCK/TIMER button (9, 23 – 26)

e PHONES jack (10)

• A/B (operating deck),

(recording), 2 3 (tape

direction), and

(reverse mode) indicators

3 CD track number (1 – 16) indicators

4 Tuner operation indicators

• MONO and ST (stereo) indicators

5 Disc indicators

r RDS operation buttons

• DISPLAY MODE button (13)

• PTY/EON button (13, 14)

• SELECT + / – buttons (13, 14)

t CD REC START button (21, 22)

y EDIT button (22)

6 SOUND MODE indicator

7 CD play mode indicators

• REPEAT (ALL/1/DISC), PRGM (program), and

RANDOM indicators

u Deck A cassette holder (19)

i 0 EJECT button for deck A (19)

o Disc number buttons and lamps (CD1, CD2, and CD3)

(16, 17, 21, 22)

Pressing one of these buttons also turns on the unit.

; SET/DISPLAY button (9, 11, 12, 17, 22 – 26)

8 RDS operation indicators

• RDS, EON, and TA/NEWS/INFO indicators

9 SUBWOOFER LEVEL indicator

p Main display

• Shows the source name, frequency, etc.

q Audio level indicator

– 4 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Control

1 Disc number buttons (CD1, CD2, and CD3) (16, 17)

Pressing one of these buttons also turns on the unit.

2 Number buttons (12, 16, 17)

3 4 (reverse search) button (12, 16, 17, 19)

4 7 (stop) button (16 – 22, 25)

5 RDS operation buttons

• DISPLAY MODE button (13)

• PTY/EON button (13, 14)

• SELECT + / – buttons (13, 14)

6 REC START/STOP button (20 – 22, 25)

7 SOUND MODE button (10)

8 FADE MUTING button (10)

9 STANDBY/ON

p SLEEP button (26)

q AUX button (9)

button (9)

Pressing this button also turns on the unit.

w FM/AM button (9, 12)

Pressing this button also turns on the unit.

e FM MODE button (12)

r CD 3¥8 button (9, 16 – 18)

Pressing this button also turns on the unit.

t ¢ (forward search) button (12, 16 – 19)

y TAPE 2 3 button (9, 19, 20)

Pressing this button also turns on the unit.

u TAPE A/B button (19)

i SUBWOOFER LEVEL + / – buttons (10)

o VOLUME + / – buttons (10)

STANDBY/ON

PLAY

EXCHANGE

STANDBY

CD-R/RW PLAYBACK

When using the remote control, point it at

the remote sensor on the front panel.

– 5 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Started

Continued

Supplied Accessories

Connecting Antennas

Make sure that you have all the following items.

The number in the parentheses indicates the quantity of the

pieces supplied.

FM antenna

ANTENNA

• AM (MW/LW) loop antenna (1)

• FM antenna (1)

• Remote control (1)

• Batteries (2)

FM antenna (supplied)

AM EXT

LOOP

FM 75

COAXIAL

If anything is missing, consult your dealer immediately.

Putting the Batteries into the Remote Control

Insert the batteries — R6(SUM-3)/AA(15F) — into the

remote control, by matching the polarity (+ and –) on the

batteries with the + and – markings on the battery

compartment.

When the remote control can no longer operate the unit,

replace both batteries at the same time.

1 Attach the FM antenna to the FM 75 Ω

COAXIAL terminal.

2 Extend the FM antenna.

3 Fasten it up in the position which gives you

the best reception, then fix it on the wall, etc.

About the supplied FM antenna

The FM antenna supplied with this unit can be used as temporary

measure. If reception is poor, you can connect an outdoor FM

antenna.

R6(SUM-3)/AA(15F)

To connect an outdoor FM antenna

Before connecting it, disconnect the supplied FM antenna.

Outdoor FM antenna

(not supplied)

ANTENNA

AM EXT

LOOP

FM 75

COAXIAL

• DO NOT use an old battery together with a

new one.

• DO NOT use different types of batteries

together.

• DO NOT expose batteries to heat or flame.

• DO NOT leave the batteries in the battery

compartment when you are not going to use

the remote control for an extended period of

time. Otherwise, it will be damaged from

battery leakage.

A 75 Ω antenna with coaxial type connector (DIN 45325)

should be used.

– 6 –

Download from Www.Somanuals.com. All Manuals Search And Download.

AM (MW/LW) antenna

Connecting Speakers

ANTENNA

Vinyl-covered wire

(not supplied)

Red

AM EXT

AM LOOP

Speaker cords

(red/black)

Speaker cords

SUBWOOFERS

LEFT

(red/black)

RIGHT

FM 75

COAXIAL

Black

RIGHT

LEFT

SPEAKERS

MAIN

CAUTION: SPEAKER

IMPEDANCE

Blue

AM (MW/LW) loop

antenna (supplied)

Speaker cords

(blue/black)

1 Connect the AM (MW/LW) loop antenna to

the AM LOOP terminals as illustrated.

• If the AM (MW/LW) loop antenna wire

is covered with vinyl, remove the vinyl

by twisting it as shown in the diagram.

2 Turn the AM (MW/LW) loop antenna until

Right speaker

Left speaker

you have the best reception.

To connect an outdoor AM (MW/LW) antenna

When reception is poor, connect a single vinyl-covered wire

to the AM EXT terminal and extend it horizontally. The AM

(MW/LW) loop antenna must remain connected.

1 Open the speaker terminals on the rear of the

unit.

2 Insert the end of the speaker cord into the

terminal.

Match the polarity (colors) of the speaker terminals: Red

(+) to red (+) and black (–) to black (–); Blue (+) to blue

(+) and black (–) to black (–).

For better reception of both FM and AM (MW/LW)

• Make sure the antenna conductors do not touch any other

terminals and connecting cords.

• Keep the antennas away from metallic parts of the unit,

connecting cords, and the AC power cord.

3 Close the speaker terminals.

IMPORTANT: Use only speakers with the same speaker

impedance as indicated by the speaker terminals on the

rear of the unit.

– 7 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Other Equipment

Now, you can plug the AC power cord.

You can connect both analog and digital equipment.

When connecting the AC power cord into a wall outlet, the

unit automatically starts display demonstration.

• DO NOT connect any equipment while the power

is on.

• DO NOT plug in any equipment until all

connections are complete.

IMPORTANT: Be sure to check all connections to be done

before plugging the AC power cord into a wall outlet.

To connect an analog component

Canceling the Display Demonstration

Be sure that the plugs of the audio cords are colored: White

plugs and jacks are for left audio signals, and red ones for

right audio signals.

On the unit ONLY:

To cancel the display demonstration, press

CANCEL/DEMO until “DEMO OFF” appears

on the display.

When you press other buttons

The display demonstration stops temporarily. It will start

automatically again (if no operation is done for 2 minutes) unless

you cancel it by pressing CANCEL/DEMO.

Audio equipment

To audio output

To start the display demonstration manually

Press and hold CANCEL/DEMO again for more than 1

second (while Ecology Mode is deactivated).

For playing the other equipment through this unit,

connect between the audio output jacks on the other

equipment and AUX jacks by using audio cords (not

supplied).

To connect audio equipment with an optical digital

input terminal

You can record CD sound onto the connected digital

equipment.

CD OPTICAL

Protective

DIGITAL OUTPUT

plug

Before connecting the

other equipment,

remove the protective

plug from the terminal.

Audio equipment with

an optical digital input

To optical digital input

Connect an optical digital cord (not supplied) between the

optical digital input terminal on the other equipment and the

CD OPTICAL DIGITAL OUTPUT terminal.

– 8 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Common Operations

Turning On or Off the Power

Setting the Clock

STANDBY/ON

To turn on the unit, press

Before operating the unit any further, first set the clock built

in this unit. You can set the clock whether the system is on or

off.

STANDBY/ON

so that the

STANDBY

STANDBY lamp goes off.

On the unit ONLY:

1 Press CLOCK/TIMER.

STANDBY/ON

To turn off the unit (on standby), press

The hour digits start flashing on the display.

STANDBY/ON

again so that the

STANDBY

STANDBY lamp lights up.

• The clock appears on the display (if

Ecology Mode is not activated).

2 Turn 4 / ¢ to adjust the

hour, then press SET/DISPLAY.

The minute digits start flashing on

the display.

• A little power is always consumed even while the unit is on

standby.

To switch off the power supply completely, unplug the AC

power cord from the AC outlet.

When you unplug the AC power cord or if a power

failure occurs

The clock is reset to “0:00” right away, while the tuner preset

stations (see page 12) will be erased in a few days.

• If you want to correct the

hour after pressing

SET/DISPLAY, press

CANCEL/DEMO.

The hour digits start flashing again.

Saving the Power Consumption While on

Standby — Ecology Mode

3 Turn 4 / ¢ to adjust the

minute, then press SET/DISPLAY.

You can save the power consumption only while the unit is

turned off (on standby).

To activate the Ecology Mode, press ECO.

“ECO” appears and the display illumination

(including the display demonstration) disappears

from the display.

• Each time you press the button, “ECO” and

“NORMAL” appear alternately on the display.

To check the clock time

Press and hold SET/DISPLAY while playing any source.

• Each time you press and hold the button, the source

indication and the clock time alternate on the display.

To adjust the clock again

To deactivate the Ecology Mode, press ECO again.

“NORMAL” appears and the display illumination appears on

the display.

If you have adjusted the clock before, you need to press

CLOCK/TIMER repeatedly until the clock setting mode is

selected.

• Each time you press the button, the clock/timer setting

modes change as follows:

About Ecology Mode

• You can also activate and deactivate Ecology Mode while the unit

is on, but it takes effect only when the unit is on standby.

• While Ecology Mode is activated, the display demonstration is

canceled temporarily.

ON TIME

REC

DAILY

Clock

Canceled

ON TIME

setting

(The hour digits start flashing.)

When you unplug the AC power cord or if a power

failure occurs

The clock loses the setting and is reset to “0:00.” You need to set the

clock again.

– 9 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Continued

Selecting the Sources

Reinforcing the Bass Sound

To listen to the FM/AM (MW/LW) broadcasts, press

FM/AM. (See page 12.)

To play back CDs, press CD 3¥8. (See pages 15 – 18.)

To play back tapes, press TAPE 2 3. (See page 19.)

To select the external equipment as the source, press AUX.

You can select one of the 4 subwoofer levels. This function

only affects the playback sound, but does not affect your

recording. The subwoofer level can be adjusted in 4 steps —

LEVEL 1, LEVEL 2, LEVEL 3, and LEVEL 4 (MAX

LEVEL).

Turn SUBWOOFER LEVEL + / –

clockwise (+) to increase the subwoofer

sound or counterclockwise (–) to

decrease it.

When using the remote control, press

SUBWOOFER LEVEL + to increase the subwoofer volume

or press SUBWOOFER LEVEL – to decrease it.

When you press the play button for a particular source

(FM/AM, CD 3/8, TAPE 2 3, and AUX), the unit turns on

(and the unit starts playing the source if it is ready —

COMPU PLAY CONTROL).

SUBWOOFER indicator always lights up

when the unit is on.

About the audio level indicator

All the audio level indicators light up when no signals come in.

Adjusting the Volume

You can adjust the volume level only while the unit is turned

on. The volume level can be adjusted in 32 steps (VOL MIN,

VOL 01 — VOL 30, and VOL MAX).

Selecting the Sound Modes

You can select one of the 6 preset sound modes (3 surround

modes and 3 SEA — Sound Effect Amplifier — modes). This

function only affects the playback sound, but does not affect

your recording.

Turn VOLUME + / – clockwise (+) to

increase the volume or

counterclockwise (–) to decrease it.

To select the sound modes, turn

SOUND MODE (or press

SOUND MODE on the remote control)

until the sound mode you want appears on

When using the remote control, press

VOLUME + to increase the volume or

press VOLUME – to decrease it.

the display.

The SOUND MODE indicator

also lights up on the display.

For private listening

Connect a pair of headphones to the PHONES jack. No sound

comes out of the speakers. Be sure to turn down the volume before

connecting or putting on headphones.

DO NOT turn off (on standby) the unit with the

volume set to an extremely high level; otherwise, a

sudden blast of sound can damage your hearing,

speakers and/or headphones when you turn on the

unit or start playing any source next time.

REMEMBER you cannot adjust the volume level

while the unit is on standby.

• The sound modes change as follows:

D.CLUB

(Dance CLUB)

HALL

STADIUM

ROCK

POP

OFF

(Canceled)

CLASSIC

MANUAL 1

MANUAL 3

MANUAL 2

To turn down the volume level temporarily

Press FADE MUTING on the remote control.

The volume level gradually decreases to

“VOL MIN.”

*When using the remote control, the sound mode changes in

only one way.

To restore the sound, press the button again.

– 10 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Surround modes**:

D.CLUB: Increases resonance and bass.

3 Adjust the SEA pattern.

HALL:

Adds depth and brilliance to the sound.

1) Turn 4 / ¢ to select the

frequency range to adjust

(LOW, MID, HIGH).

STADIUM: Adds clarity and spreads the sound, like in an

outdoor stadium.

SEA (Sound Effect Amplifier) modes:

2) Press 1 or ¡ to adjust

the level (–3 to +3) of the

selected frequency range.

ROCK:

Boosts low and high frequency. Good for

acoustic music.

POP:

Good for vocal music.

CLASSIC: Good for classical music.

3) Repeat steps 1) and 2) to

adjust the level of the other

frequency ranges.

Manual modes:

MANUAL 1/2/3:

Your individual mode stored in memory. See

“Creating Your Own Sound Mode — Manual

Mode.”

4 Press SET/DISPLAY again.

OFF:

The sound mode is canceled. The SOUND

MODE indicator goes off.

** Surround elements are added to the SEA elements to create a

being-there feeling in your room.

When one of these modes is selected, the SOUND MODE

indicator lights up as —

5 Turn 4 / ¢ to select one of the

MANUAL 1, MANUAL 2, and MANUAL 3

modes into which you want to store the SEA

pattern.

While one of the SEA modes including manual modes (SEA

elements without surround elements) is selected, the SOUND

MODE indicator lights up as —

6 Press SET/DISPLAY again.

Creating Your Own Sound Mode

— Manual Mode

You can change SEA pattern to suit your preference. These

changed settings can be stored in the MANUAL 1,

MANUAL 2, and MANUAL 3 modes.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1 again.

The SEA pattern you have created are stored into the

MANUAL mode selected in the above step.

To use your own sound mode

On the unit ONLY:

Select MANUAL 1, MANUAL 2, or MANUAL 3 mode

when using the sound modes. See “Selecting the Sound

Modes” on page 10.

1 Select one of the preset sound modes.

• If you want to add the surround elements in your SEA

pattern, select one of the surround modes (D.CLUB,

HALL, or STADIUM) before starting the procedurem

below. (See “Selecting the Sound Modes” on page 10.)

When you unplug the AC power cord or if a power

failure occurs

The setting will be erased in a few days. If this happens, set the

manual sound modes again.

2 Press and hold SET/DISPLAY until “SEA

CONT” appears on the display.

Current level appears.

– 11 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to FM and AM (MW/LW) Broadcasts

Tuning in a Station

On the unit ONLY:

1 Tune in the station you want to preset.

1 Press FM/AM.

• See “Tuning in a Station.”

The unit automatically turns on and

tunes in the previously tuned station

(either FM or AM — MW/LW).

• Each time you press the button, the

band alternates between FM and AM

(MW/LW).

2 Press SET/DISPLAY.

2 Start searching for stations.

On the unit:

3 Turn PRESET + / – to select a

preset number.

Press and hold TUNING +

or TUNING – for more than

1 second.

On the remote control:

Press and hold ¢ or 4

for more than 1 second.

The unit starts searching for stations

and stops when a station of sufficient

signal strength is tuned in.

4 Press SET/DISPLAY again.

• If a program is broadcast in stereo, the ST (stereo)

indicator lights up.

The tuned station in step 1 is stored in the

preset number selected in step 3.

• Storing a new station on a used number erases the

previously stored one.

To stop searching, press TUNING + or TUNING – (or ¢ /

4 on the remote control).

When you unplug the AC power cord or if a power

failure occurs

The preset stations will be erased in a few days. If this happens,

preset the stations again.

When you press TUNING + or TUNING – (or ¢ /

4 on the remote control) briefly and repeatedly

The frequency changes step by step.

To change the FM reception mode

When an FM stereo broadcast is hard to receive

or noisy, press FM MODE on the remote

control so that the MONO indicator lights up

on the display. Reception improves.

Tuning in a Preset Station

1 Press FM/AM.

The unit automatically turns on and

tunes in the previously tuned station

(either FM or AM — MW/LW).

• Each time you press the button, the

band alternates between FM and AM

(MW/LW).

To restore the stereo effect, press FM MODE again so that

the MONO indicator goes off. In this stereo mode, you can

hear stereo sounds when a program is broadcasted.

Presetting Stations

2 Select a preset number.

On the unit:

You can preset 30 FM and 15 AM (MW/LW) stations.

In some cases, test frequencies have been already memorized

for the tuner since the factory examined the tuner preset

function before shipment. This is not a malfunction. You can

preset the stations you want into memory by following the

presetting method.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1

again.

Turn PRESET + / –.

On the remote control:

Press the number buttons.

Ex.: For preset number 5, press 5.

For preset number 15, press

+10, then 5.

For preset number 20, press

+10, then 10.

For preset number 25, press

+10, +10, then 5.

For preset number 30, press

+10, +10, then 10.

– 12 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Receiving FM Stations with RDS

RDS (Radio Data System) allows FM stations to send an

Searching for Programs by PTY Codes (PTY

additional signal along with their regular program signals.

For example, the stations send their station names, as well as

information about what type of program they broadcast, such

as sports or music, etc.

Search)

One of the advantages of RDS is that you can locate a

particular kind of program by specifying the PTY codes.

• For details on the PTY codes, see “Additional Information”

on page 27.

When tuned to an FM station which provides the RDS

service, the RDS indicator lights up on the display.

To search for a program using the PTY codes

REMEMBER you must preset FM RDS stations to use the

PTY codes. If not yet done, see page 12.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1

again.

With the unit, you can receive the following types of RDS

signals.

PS (Program Service):

Shows commonly known station names.

PTY (Program Type):

Shows types of broadcast programs.

1 Press PTY/EON until “PTY” and

“SELECT” alternately appear on

the display.

RT (Radio Text):

Shows text messages the station sends.

EON (Enhanced Other Networks):

Provides the information about the types of the

programs sent by other RDS stations.

• Each time you press the button, RDS operation mode

changes as follows:

PTY SELECT

EON SELECT

(See page 14.)

Canceled

More about RDS

• Some FM stations do not provide RDS signals.

• RDS services vary among FM RDS stations. For details on RDS

services in your area, check with local radio stations.

• RDS may not work correctly if the received station is not

transmitting the signals properly or if the signal strength is weak.

2 Press SELECT + or SELECT –

until the PTY code you want

appears on the display.

Changing the RDS Information

• Each time you press the button, the PTY codes change

as follows:

You can see RDS information on the display while listening

to an FM station.

NEWS “ AFFAIRS “ INFO “ SPORT “

EDUCATE “ DRAMA “ CULTURE “

SCIENCE “ VARIED “ POP M “ ROCK M “

M.O.R. M “ LIGHT M “ CLASSICS “

OTHER M “ WEATHER “ FINANCE “

CHILDREN “ SOCIAL A “ RELIGION “

PHONE IN “ TRAVEL “ LEISURE “ JAZZ

“ COUNTRY “ NATIONAL “ OLDIES “

FOLK M “ DOCUMENT “

Press DISPLAY MODE.

• Each time you press the button, the display

changes to show the following information:

PTY

(Radio Text)

(Program Service) (Program Type)

Station frequency

(or preset channel no.)

(back to the beginning)

• If no PS, PTY, or RT signals are sent by a station

“NO PS,” “NO PTY,” or “NO RT” appears in the main display.

• If the unit takes time to show the RDS information received

from a station

“WAIT PS,” “WAIT PTY,” or “WAIT RT” may appear on the

display.

3 Press PTY/EON once again.

While searching, “SEARCH” and the

selected PTY code alternate on the display.

The unit searches 30 preset FM stations,

stops when it finds the one you have selected (“FOUND”

appears), and tunes in that station.

• If no program is found, “NOT” and “FOUND” appear

on the display and the unit returns to the last received

station.

To stop searching any time during the process

Press PTY/EON while searching.

– 13 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Switching to a Program Type of Your Choice

Temporarily

How the EON function actually works:

CASE 1

By receiving EON (Enhanced Other Networks) data sent by

FM RDS stations, the EON function allows the unit to switch

temporarily to a broadcast program of your choice (TA,

NEWS, or INFO) from a different station.

• The EON function only works when you are listening to a

preset FM RDS stations providing EON data.

• The EON indicator lights while receiving a station with the

EON data.

If there is no station broadcasting the program you

have selected

The unit continues tuning in the current station.

When a station starts broadcasting the program you have

selected, the unit automatically switches to the station. The

indicator of received PTY code starts flashing.

When the program is over, “EON END” appears on the

display, and the unit goes back to the previously tuned

station, but the EON function still remains activated.

To activate the EON function

REMEMBER you must preset FM RDS stations to use the

EON function. If not yet done, see page 12.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1

again.

CASE 2

If there is a station broadcasting the program you have

selected

The unit tunes in the program. The indicator of received

PTY code starts flashing.

1 Press PTY/EON until “EON” and

“SELECT” alternately appear on

the display.

When the program is over, “EON END” appears on the

display, and the unit goes back to the previously tuned

station, but the EON function still remains activated.

• Each time you press the button, RDS operation mode

changes as follows:

PTY SELECT

(See page 13.)

EON SELECT

CASE 3

Canceled

If the FM station you are listening to is broadcasting

the program you have selected

The unit continues to receive the station but the indicator

of received PTY code starts flashing.

When the program is over, “EON END” appears on the

display, and the indicator of received PTY code stops

flashing and remains lit, but the EON function still

remains activated.

2 Press SELECT + or SELECT –

until the EON data type you want

appears on the display.

The selected EON data type indicator also flashes.

More about the EON function

• Each time you press the button, the EON data types

change as follows:

• The EON data sent from some stations may not be compatible

with this unit. In this case, the EON function may not work

correctly.

NEWS

INFO

OFF

(Canceled)

• While listening to a program tuned in by the EON function, the

station does not change even if another network station starts

broadcasting a program of the same EON data.

• The EON function is canceled when you change the source to CD,

TAPE, or AUX, while it is temporarily canceled when you change

the source to AM.

TA:

NEWS: News

Traffic announcement

INFO: Program the purpose of which is to impart advice

in the widest sense.

OFF: The EON function is canceled. The EON data

type indicator (TA, NEWS, INFO) goes off.

3 Press PTY/EON once again.

The EON data type indicator stops flashing

and remains lit.

Now, the EON function is activated. See

“How the EON function actually works.”

– 14 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing Back CDs (CD/CD-R/CD-RW)

This unit has been designed to playback the following CDs:

• CD (Audio CD)

Loading CDs

• CD-R (CD-Recordable)

• CD-RW (CD-ReWritable)

On the unit ONLY:

1 Press 0 for the disc tray

(CD1, CD2, and CD3) you

want to load a CD onto.

The unit automatically turns on and

the disc tray comes out.

Continued use of irregular shape CDs

(heart-shape, octagonal, etc.) can damage

the System.

2 Place a disc correctly on the circle of the disc

General Notes

tray, with its label side up.

In general, you will have the best performance by keeping

your CDs and the mechanism clean.

• Store CDs in their cases, and keep them in cabinets or on

shelves.

• Keep the system’s disc trays closed when not in use.

CORRECT

INCORRECT

• When using a CD single (8 cm), place it on the inner

circle of the disc tray.

When playing a CD-R or CD-RW

User-edited CD-Rs (CD-Recordable) and CD-RWs

(CD-ReWritable) can be played back only if they are already

“finalized.”

3 Press the same 0 you have

pressed in step 1.

• You can play back your original CD-Rs or CD-RWs

recorded in music CD format. (However, they may not be

played back depending on their characteristics or recording

conditions.)

• Before playing back CD-Rs or CD-RWs, read their

instructions or cautions carefully.

The disc tray closes, and the

corresponding disc number lamp and

disc indicator light up on the display

(CD1, CD2, and CD3).

• Some CD-Rs or CD-RWs may not be played back on this

unit because of their disc characteristics, damage or stain

on them, or the player’s lens is dirty.

4 Repeat steps 1 to 3 to place other CDs.

• CD-RWs may require a longer readout time. This is caused

by the fact that the reflectance of CD-RWs is lower than for

regular CDs.

When loading more than one CD continuously

When you press 0 for the next tray you want to place another CD

onto, the first disc tray automatically closes and then the next tray

comes out.

About the disc indicators

Each disc indicator corresponds to the disc tray of the same number.

Disc number

Disc indicator

Disc marker

• The disc marker lights up for the disc number you have selected.

• The disc indicator flashes while the corresponding CD is being

played.

• The disc indicators goes off when the unit has detected that there

is no CD on the corresponding disc tray.

– 15 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Continued

Playing Back the Entire Discs

— Continuous Play

Basic CD Operations

While playing a CD, you can do the following operations.

1 Load CDs.

To exchange CDs during playback of another

Press 0 corresponding to a CD, not playing or selected

currently, to eject and exchange the CD.

If you exchange CDs during play, the current play will not

stop until all CDs you have exchanged are played.

2 Press one of the disc number

buttons (CD1, CD2, and

CD3) for the disc you want to

play.

CD play starts from the first track of

the selected disc and the disc number lamp starts flashing.

To stop play for a moment

Press CD 3¥8.

While pausing, the elapsed playing time

flashes on the display.

Tracks of the currently playing disc

(Track numbers exceeding 16 are not displayed.)

To resume playing, press CD 3¥8.

To go to another track

Turn 4 / ¢ before or during

playback (or press 4 / ¢ on the

remote control).

• 4:Goes back to the beginning of

the current or previous tracks.

• ¢:Skips to the beginning of the

next or succeeding tracks.

Track number Elapsed playing time

• Pressing CD 3/8 instead of the disc number buttons

starts playing back if a CD is on the trays.

• If no CD is placed on the selected disc tray, “NO DISC”

appears on the display.

If you turn 4 / ¢ (or press 4 / ¢ on the remote

control) before playing

You can change the tracks continuously.

To stop playing, press 7.

To locate a particular point in a track

During play, press and hold 1 or ¡

(or 4 / ¢ on the remote control).

• 1 (or 4): Fast reverses the disc.

• ¡ (or ¢): Fast forwards the disc.

To remove the disc, press 0 for the corresponding disc tray.

CD playback sequence

When 3 CDs* are loaded on the disc trays, they are played in one of

the following sequences.

To go to another track directly using the number

• When CD1 is pressed: CD1 ] CD2 ] CD3 (then stops)

• When CD2 is pressed: CD2 ] CD3 ] CD1 (then stops)

• When CD3 is pressed: CD3 ] CD1 ] CD2 (then stops)

* When only 2 CDs are loaded, they are played in the same order,

but the disc tray without a CD is skipped.

buttons

Pressing the number button(s) on the remote control before or

during play allows you to start playing the track number you

want.

Ex.: For track number 5, press 5.

For track number 15, press +10,

then 5.

For track number 20, press +10,

then 10.

For track number 32, press +10,

+10, +10, then 2.

– 16 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming the Playing Order of the Tracks

— Program Play

5 Program other tracks you want.

• To program tracks from the same disc, repeat step 4.

• To program tracks from a different disc, repeat steps 3

and 4.

You can arrange the order in which tracks play before you

start playing. You can program up to 32 tracks.

• To use Repeat play (see page 18) for Program play, press

REPEAT after starting Program play.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 2

again.

6 Press CD 3¥8.

The tracks are played in the order you

have programed.

To stop playing, press 7.

To exit from Program play mode, press PROGRAM again

before or after play. The PRGM (program) indicator goes off.

The program you have made is stored in memory.

1 Load CDs.

• If the current playing source is not the CD player, press

CD 3¥8, then 7 before going to the next step.

2 Press PROGRAM so that

“PROGRAM” appears on the

display.

• If you try to program a 33rd track

“FULL” will appear on the display.

• If your entry is ignored

The PRGM (program) indicator also lights up on the

display.

You have tried to program a track from an empty tray, or a track

number that does not exist on the CD (for example, selecting track

14 on a CD that only has 12 tracks). Such entries are ignored.

• If the total playing time is 100 minutes or more

“– – : – –” will appear on the display.

• If a program has been stored in memory, the program is

called up.

To check the program contents

Before playing, you can check the

program contents by pressing ¢ or 4

on the remote control.

3 Press one of the disc number

buttons (CD1, CD2, and

CD3) to select the disc

• ¢ : Shows the programed tracks in

number you want to play.

the programed order.

Track number

• 4 : Shows them in the reverse order.

To modify the program

Before or after playing, you can erase the last

programed tracks by pressing

CANCEL/DEMO.

• Each time you press the button, the programed

track shown on the display is erased from the

program.

• Ejecting a CD will also erase the track numbers

programmed from the ejected CD.

Disc number

Program step number

4 Select a track from the CD

selected in the above step.

On the unit:

Turn 4 / ¢ to select the

track number and press

SET/DISPLAY.

On the remote control:

Press the number buttons.

• For how to use the number buttons,

see “To go to another track directly

using the number buttons” on page 16.

To add tracks in the program before playing, simply select

the track numbers you want to add by following step 4 of the

programming procedure.

To erase the entire program before or after playing, press

7. “PROGRAM” appears on the display.

The program you have made will be also erased,

• when you eject all the CDs.

• when you unplug the AC power cord.

• when a power failure occurs.

– 17 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing at Random — Random Play

Repeating Tracks or CDs — Repeat Play

The tracks of all loaded CDs will play at random.

• To use Repeat play for Random play, press REPEAT after

starting Random play.

You can have all the CDs, the program or the individual track

currently playing repeat as many times as you like.

On the unit ONLY:

1 Load CDs.

To repeat playing, press REPEAT during or

before play. To use Repeat play for Program

play and Random play, press the button after

starting playback.

• If the current playing source is not the CD player, press

CD 3¥8, then 7 before going to the next step.

2 Press RANDOM so that

“RANDOM” appears on the display.

The RANDOM indicator also lights up on the

display.

• Each time you press the button, Repeat play mode changes

as follows, and the following indicator lights up on the

display:

REPEAT ALL

Canceled

REPEAT 1 DISC

REPEAT 1

REPEAT ALL:

Repeats all the tracks on all the CDs

(continuously or at random), or all the

tracks in the program.

3 Press CD 3¥8.

REPEAT 1 DISC: Repeats all the tracks on one CD.

• REPEAT 1 DISC is not used for

The tracks are played at random.

Random play ends when all the tracks

are played once.

Program play and Random play.

REPEAT 1:

Repeats one track on one CD.

To skip the currently playing track, turn 4 / ¢ to the

right (or press ¢ on the remote control).

To cancel Repeat play, press REPEAT repeatedly until the

REPEAT indicators go off from the display.

• Repeat play is also canceled when you select Program play

or Random play.

Even if you turn 4 / ¢ to the left (or press 4 on

the remote control)

You cannot go back to the previous tracks during Random play.

Prohibiting Disc Ejection — Tray Lock

To stop playing, press 7.

• Random play also stops when one of the disc trays is

opened.

You can prohibit CD ejection from the unit and lock CDs.

• This operation is possible only when the source is the CD

player.

To exit from Random play mode, press RANDOM again

before or after play.

On the unit ONLY:

To prohibit disc ejection, press 0 for

any disc tray while holding down 7. (If

there is any disc tray opened, close it

first.)

“LOCKED” appears for a while, and the

loaded CDs are locked.

To cancel the prohibition and unlock

the CDs, press 0 for any disc tray while

holding down 7.

“UNLOCKED” appears for a while, and

the loaded CDs are unlocked.

If you try to eject CDs

“LOCKED” appears to inform you that the Tray Lock is in use.

– 18 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing Back Tapes

You can play back type I, type II, and type IV tapes without

changing any settings.

To play both sides repeatedly — Reverse Mode

Reverse Mode works for both decks at the same time.

When it is in use, the tape automatically reverses at the end of

a side and the unit starts playing for the other side of the tape,

and repeats the same process.

Playing Back a Tape

To use Reverse Mode, press

REVERSE MODE so that the Reverse Mode

indicator on the display lights up like —

1 Press EJECT (0) for the deck you want to

use.

To cancel Reverse Mode, press the button

again so that the Reverse Mode indicator on the

display lights up like —

For Deck B

When Reverse Mode is on with cassettes in both decks

A and B

For Deck A

2 Put a cassette in with the exposed part of the

tape down.

After the reverse (2) side of the tape finishes playing, the tape in the

other deck starts playing.

Locating the Beginning of a Song

— Music Scan

You can use Music Scan to locate the beginning of a song.

Music Scan searches for blank portions that usually separate

recorded songs, then plays the next song.

3 Close the cassette holder gently.

If you put cassettes in both decks A and B, the last deck

you have put a cassette into is selected.

To find the beginning of the current song

During play, press 1 or ¡ (4 or

¢ on the remote control) in the opposite

direction to the tape play.

To select the other deck, press TAPE A/B.

The tape direction indicator of the opposite

direction to the tape play starts flashing

slowly.

4 Press TAPE 2 3.

The tape play starts and the tape

direction indicator (3 or 2) starts

flashing slowly to indicate the tape

running direction.

Searching stops automatically at the beginning of the current

song, and the current song starts automatically.

• Each time you press the button, the

tape direction changes.

3 : plays the front side.

2 : plays the reverse side.

• If no cassette is inserted, “NO TAPE” appears on the

display.

When the tape plays to the end, the deck automatically

stops if the Reverse Mode is off. (See “To play both sides

repeatedly — Reverse Mode.”)

To find the beginning of the next song

During play, press 1 or ¡ (4 or

¢ on the remote control) in the same

direction as the tape play.

The tape direction indicator of the same

direction as the tape play starts flashing

slowly and quickly alternately.

Searching stops automatically at the beginning of the next

song, and the next song starts automatically.

Music Scan works by detecting a 4-second long blank

between each song, so it will not work well in the

following cases

To stop playing, press 7.

To operate the other deck, press TAPE A/B,

then TAPE 2 3.

• No blank at the beginning of a song.

• Noise (often caused by much use or poor quality dubbing) which

fills the blank.

To fast-wind to the left or to the right, press 1 or ¡

(4 or ¢ on the remote control) while the tape is not

running.

• Long, very soft passages or pauses in a song.

The use of the C-120 or thinner tape is not

recommended, since characteristic deterioration

may occur and this tape easily jams in the pinch-

rollers and the capstans.

The tape direction indicator (3 or 2) starts flashing quickly

on the display.

To remove the cassette, press 0 EJECT for deck A or

EJECT 0 for deck B.

– 19 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording

Continued

IMPORTANT:

Recording a Tape on Deck B

• It should be noted that it may be unlawful to re-record

pre-recorded tapes, records, or discs without the

consent of the owner of copyright in the sound or video

recording, broadcast or cable programme and in any

literary, dramatic, musical, or artistic embodied

therein.

1 Press EJECT 0 for the deck B.

• The recording level is automatically set correctly, so it is

not affected by the VOLUME, the SUBWOOFER LEVEL,

and the SOUND MODE controls. Thus, during recording

you can adjust the sound you are actually listening to

without affecting the recording level.

• If recordings you have made have excessive noise or static,

the unit may be too close to a TV. Increase the distance

between the TV and the unit.

2 Put a recordable cassette into deck B.

3 Close the cassette holder gently.

• You can use type I tape for recording.

4 Check the tape direction of deck B.

• If the tape direction is not correct, press TAPE 2 3

twice then 7 to change the tape direction.

To protect your recording

Cassettes have two small

tabs on the back to protect

from unexpected erasure or

re-recording.

To protect your recording,

remove these tabs.

To re-record on a protected tape, cover the holes with

adhesive tape.

5 Start playing the source — FM, AM (MW/

LW), CD player, deck A, or auxiliary

equipment connected to AUX jacks.

• When the source is CD, you can also use CD Direct

Recording (see page 21) and Auto Edit Recording (see

page 22).

• When the source is deck A, you can also use the

dubbing method. (See “Dubbing Tapes” on page 21.)

To keep the best recording and playback sound quality

If the heads, capstans, and pinch rollers of the cassette decks

become dirty, the following will occur:

• Impaired sound quality

• Discontinuous sound

• Fading

6 Start recording.

On the unit:

Press REC START/STOP.

On the remote control:

Press and hold REC START/STOP

for more than 1 second.

• Incomplete erasure

• Difficulty in recording

The

(recording) indicator lights up on

the display and recording starts.

To clean the heads, capstans, and pinch rollers

Use a cotton swab moistened with alcohol.

• If no cassette is inserted, “NO TAPE” appears on the

display. If a protected tape is inserted, “NO REC”

appears on the display.

Pinch rollers

Capstans

To stop recording immediately, press 7.

To remove the cassette, press EJECT 0 for deck B.

Heads

To demagnetize the heads

Turn off the unit, and use a head demagnetizer (available at

electronics and audio shops).

– 20 –

Download from Www.Somanuals.com. All Manuals Search And Download.

To record on both sides — Reverse Mode

Press REVERSE MODE so that the Reverse

CD Direct Recording

Everything on the CD goes onto the tape in the order it is on

the CD, or according to the order you have made for Program

play.

Mode indicator lights up like —

• When using the Reverse Mode for recording,

start recording in the forward (3) direction

first. Otherwise, recording will stop when recording is done

only on one side (reverse) of the tape.

On the unit ONLY:

1 Put a recordable cassette into deck B.

To cancel Reverse Mode, press the button again so that the

Reverse Mode indicator lights up like —

2 Load CDs.

3 Press one of the disc

Dubbing Tapes

number buttons (CD1,

You can record from one tape to another.

CD2, and CD3) to select

the disc, then 7.

On the unit ONLY:

• If you want to make a program, perform steps 2 to 5 on

page 17. After making a program, go to the next step.

1 Press TAPE 2 3, then 7.

4 Press CD REC START.

“CD REC” appears, and the

(recording) indicator lights up on the

display.

Deck B starts recording and the CD player starts playing.

When the recording is done, “CD REC FINISHED”

appears on the display, and the CD player and deck B

stop.

2 Put the source cassette in deck A, and a

recordable cassette into deck B.

• Put the cassettes in both decks so that the tapes will run

in the forward (3) direction.

To stop recording, press REC START/STOP

or 7. So that a 4-second blank portion is

created on the recording tape. (Remember a 4-

second blank is important when using Music

Scan — see page 19.)

3 Press DUBBING.

The

(recording) indicator lights up on

the display and dubbing starts.

To stop dubbing, press 7 so that both decks (A and B) stop.

To record on both sides — Reverse Mode

Press REVERSE MODE so that the Reverse

Mode indicator lights up like —

To record on both sides — Reverse Mode

• When using the Reverse Mode for CD Direct

Recording, start recording in the forward (3)

Press REVERSE MODE so that the Reverse

Mode indicator lights up like —

direction first. When the tape reaches its end while

recording a song in the forward direction (3), the last song

will be re-recorded at the beginning of the reverse side (2).

If you start recording on the reverse side (2), recording

will stop when recording is done only on one side (reverse)

of the tape.

To cancel Reverse Mode, press the button

again so that the Reverse Mode indicator

lights up like —

To cancel Reverse Mode, press the button again so that the

Reverse Mode indicator lights up like —

– 21 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Edit Recording

4 Press SET/DISPLAY.

• Each time you press the button, the tracks to

be recorded on the front side (“SIDE-A”)

and on the reverse side (“SIDE-B”) alternate.

By using Auto Edit Recording, you can record the CD tracks

to fit the tape. Auto Edit Recording makes a program by

selecting the CD tracks in numerical order. However, to

prevent the end of the last track on the front side from being

cut off, the last track is selected so as to fit on the remaining

tape length.

Tracks to be recorded on the

reverse side (SIDE-B) appear.

On the unit ONLY:

1 Load CDs.

• If the current playing source is not the CD player, press

CD 3¥8, then 7 before going to the next step.

5 Put a recordable cassette of appropriate

length into deck B.

2 Press EDIT.

6 Press REVERSE MODE so that

the Reverse Mode indicator lights

up like

• Without turning on the Reverse Mode

), recording will stop when the front

(

side of the tape is recorded.

3 Press the disc number

button (CD1, CD2, and

CD3) for the disc you want

to record from.

7 Press CD REC START.

“TAPE SIDE-A STAND-BY” appears,

and the

(recording) indicator lights

up on the display.

Deck B starts recording then, about 10 seconds later, the

CD player starts playing.

When the recording is done, “CD REC FINISHED”

appears on the display, and the CD player and deck B

stop.

• If a tape has not been rewound, deck B will rewind the

tape before it starts recording.

• A 10-second blank portion is automatically created at

the beginning of each side of the tape.

To stop during Auto Edit Recording

Press REC START/STOP or 7. So that a 4-second blank

portion is created on the recording tape. (Remember a 4-

second blank is important when using Music Scan — see

page 19.)

The optimum tape length for the disc appears.

To change the tape length manually

If the tape length selected is not satisfactory, you can

change the tape length by turning 4 / ¢ on the unit.

You can select the tape length among the following

— 40, 46, 50, 54, 60, 64, 70, 74, 80, 84, and 90.

To cancel Auto Edit Recording

Press CANCEL/DEMO or 7 before or after play.

– 22 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Timers

There are three timers available — Daily Timer, Recording

Timer, and Sleep Timer.

On the unit ONLY:

1 Press CLOCK/TIMER repeatedly

until “DAILY” appears on the

display.

Before using the timers, you need to set the clock built in the

unit. (See page 9.)

indicator lights up and DAILY (Daily

Timer) indicator also starts flashing on the

display.

Using Daily Timer

With Daily Timer, you can wake to your favorite music or

radio program. You can set the timer whether the unit is on or

off.

How Daily Timer actually works

The unit automatically turns on, set the volume level to the

preset level, and starts playing the specified source when the

• Each time you press the button, the timer setting modes

change as follows:

on-time comes (the

indicator flashes just before the on-

time, and continues flashing while the timer is operating).

Then, when the off-time comes (“OFF” flashes just before the

off-time), the unit automatically turns off (on standby).

The Daily timer works everyday automatically. If you do not

want to use the Daily timer, turn off the Daily timer. (See “To

turn on or off Daily Timer after its setting is done” on page

24.) The timer setting remains in memory until you change it.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1

again.

ON TIME

REC

DAILY

Clock

setting

Canceled

ON TIME

(See page 9.)

2 Press CLOCK/TIMER again.

“ON TIME” appears for 2 seconds, then the

unit enters on-time setting mode.

• To correct a mis-entry while setting the timer, press

CANCEL/DEMO.

Before you start...

• When using a CD as the source to play —

– Make sure there is a CD on the selected disc number

tray.

• When using a tape as the source to play —

– Make sure that a tape is in the deck whose deck

indicator (A or B) is lit on the display.

– Make sure that the tape direction is correct.

• When using the external component as the source to

play —

3 Set the on-time you want the

unit to turn on at.

1) Turn 4 / ¢ to set the hour,

then press SET/DISPLAY.

2) Turn 4 / ¢ to set the minute,

then press SET/DISPLAY.

“OFF TIME” appears for 2

seconds on the display, then the

unit enters off-time setting mode.

– Set the timer equipped on the external component at

the same time.

4 Set the off-time you want the

unit to turn off (on standby) at.

1) Turn 4 / ¢ to set the hour, then press

SET/DISPLAY.

2) Turn 4 / ¢ to set the minute, then press

SET/DISPLAY.

The unit enters source selecting mode.

– 23 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Continued

STANDBY/ON

5 Turn 4 / ¢ to select the source to play,

then press SET/DISPLAY.

9 Press STANDBY/ON

STANDBY

turn off the unit (on standby)

if you have set the Daily Timer

with the unit turned on.

• The source changes as follows:

TUNER FM

AUX TAPE

TUNER AM

– CD – –

TUNER FM: tunes into a specified preset FM station.

= Go to step 6.

• If the unit is turned on when the on-time comes

Daily Timer does not work.

TUNER AM: tunes into a specified preset

AM (MW/LW) station. = Go to step 6.

– CD – –: plays a disc from a specified track of a

specified disc. = Go to step 6.

• Even if you unplug the AC power cord or if a power failure

occurs

Once you set the timer, the timer setting may remain stored in

memory in a few days. In this case, check whether the timer

setting still remains or not.

TAPE:

plays a tape in deck A or B.

= Go to step 7.

AUX:

plays an external source. = Go to step 7.

To turn on or off Daily Timer after its setting is done

6 When selecting “TUNER FM” or “TUNER

AM”

Press CLOCK/TIMER repeatedly until

“DAILY” appears on the display.

Turn 4 / ¢ to select the preset station number, then

To turn off the Daily Timer, press

CANCEL/DEMO.

indicator and the DAILY (Daily Timer)

indicator go off from the display (“OFF”

appears for a while).

The Daily Timer is canceled, but the

setting for the Daily Timer remains in

memory.

press SET/DISPLAY.

The unit enters volume setting mode.

When selecting “– CD – –”

1) Turn 4 / ¢ to select the disc number, then press

SET/DISPLAY.

2) Turn 4 / ¢ to set the track number, then press

SET/DISPLAY.

The unit enters volume setting mode.

To turn on the Daily Timer, press

SET/DISPLAY.

7 Turn 4 / ¢ to set the

volume level.

indicator and the DAILY (Daily Timer)

indicator light up on the display. The

settings you have done are shown on the

display in sequence for your confirmation.

• The volume level changes as follows:

VOL – –

VOL 15

VOL 05

VOL 10

• If you select “ VOL – –,” the volume is set to the last

level when the unit has been turned off.

8 Press SET/DISPLAY to complete

the Daily Timer setting.

The DAILY (Daily Timer) indicator stops

flashing and remains lit. The settings you

have done are shown on the display in

sequence.

– 24 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Recording Timer

4 Set the on-time you want the

unit to turn on at.

With Recording Timer, you can make a tape of a radio

broadcast automatically. You can set the timer whether the

system is on or off.

1) Turn 4 / ¢ to set the hour,

then press SET/DISPLAY.

2) Turn 4 / ¢ to set the minute,

then press SET/DISPLAY.

How Recording Timer actually works

The unit automatically turns on, tunes into the specified

station, sets the volume level to “VOL MIN,” and starts

“OFF TIME” appears for 2

seconds, then the unit enters off-

time setting mode.

recording when the on-time comes (the

indicator flashes

just before the on-time, and continues flashing while the

timer is operating). Then, when the off-time comes (“OFF”

appears just before the off-time), the unit automatically turns

off (on standby).

The timer setting remains in memory until you change it.

• There is a time limit in doing the following steps. If the

setting is canceled before you finish, start from step 1

again.

5 Set the off-time you want the

unit to turn off (on standby) at.

1) Turn 4 / ¢ to set the hour, then press

SET/DISPLAY.

2) Turn 4 / ¢ to set the minute, then press

SET/DISPLAY.

The unit enters preset station selecting mode.

• To correct a mis-entry while setting the timer, press

CANCEL/DEMO.

6 Select the preset station.

1) Turn 4 / ¢ to select the band (“TUNER FM” or

“TUNER AM”), then press SET/DISPLAY.

2) Turn 4 / ¢ to select a preset channel number,

then press SET/DISPLAY.

On the unit ONLY:

1 Put a recordable cassette into deck B.

2 Press CLOCK/TIMER repeatedly

until “REC” appears on the

display.

The REC (Recording Timer) indicator stops flashing

and remains lit. The settings you have done are shown

on the display in sequence.

STANDBY/ON

7 Press STANDBY/ON

The REC (Recording Timer) indicator also

starts flashing on the display.

STANDBY

turn off the unit (on standby)

if necessary.

• If you want to listen to another source while recording

Press REC START/STOP or 7 to stop recording. Without

stopping it, you cannot change the source.

• Even if you unplug the AC power cord or if a power failure

occurs

• Each time you press the button, the timer setting modes

change as follows:

Once you set the timer, the timer setting may remain stored in

memory in a few days. In this case, check whether the timer

setting still remains or not.

ON TIME

REC

DAILY

Clock

setting

Canceled

ON TIME

(See page 9.)

3 Press CLOCK/TIMER again.

“ON TIME” appears for 2 seconds, then the

unit enters on-time setting mode.

– 25 –

Download from Www.Somanuals.com. All Manuals Search And Download.

To turn on or off Recording Timer after its setting is

done

Timer Priority

Since each timer can be set separately, you may wonder what

happens if the setting for these timers overlaps.

Here are examples.

Press CLOCK/TIMER repeatedly until

“REC” appears on the display.

To turn off the Recording Timer, press

CANCEL/DEMO.

Recording Timer has priority over Daily Timer and Sleep

Timer.

• If Daily Timer is set to come on while Recording Timer is

operating, Daily Timer will not come on at all.

The REC (Recording Timer) indicator goes

off from the display.

The Recording Timer is canceled, but the

setting for the Recording Timer remains in

memory.

6:00

6:30

7:00

7:30

Recording Timer

Daily Timer

To turn on the Recording Timer, press

SET/DISPLAY.

does not work.

The REC (Recording Timer) indicator lights

up on the display. The settings you have done

are shown on the display in sequence for your

confirmation.

• If Recording Timer is set to come on while Sleep Timer is

operating, Sleep Timer will not work (the SLEEP indicator

does not go off).

21:00

21:30

22:00

22:30

Recording Timer

Sleep Timer

Using Sleep Timer

With Sleep Timer, you can fall asleep to music. You can set

Sleep Timer only while the unit is turned on.

does not work.

How Sleep Timer actually works

The unit automatically turns off after the specified time

length passes.

On the remote control ONLY:

1 Press SLEEP.

The time length until the shut-off time

appears and the SLEEP indicator starts

flashing on the display.

• Each time you press the button, the time length changes

as follows:

SLEEP10 SLEEP20 SLEEP30 SLEEP60

Canceled

SLEEP120

SLEEP90

2 Wait for about 5 seconds after specifying the

time length.

The SLEEP indicator stops flashing and remains lit.

To check the remaining time until the shut-off time, press

SLEEP once so that the remaining time until the shut-off time

appears for about 5 seconds.

To change the shut-off time, press SLEEP repeatedly until

the desired time length appears on the display.

To cancel the setting, press SLEEP repeatedly so that the

SLEEP indicator goes off.

• Sleep Timer is also canceled when you turn off the unit.

– 26 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional Information

Description of the PTY codes:

FINANCE: Stock Market reports, commerce, trading etc.

CHILDREN: Programs targeted at a young audience.

NEWS:

News.

SOCIAL A: Programs about sociology, history, geography,

psychology and society.

AFFAIRS:

Topical program expanding or enlarging upon the

news — debate, or analysis.

RELIGION: Religious programs.

INFO:

Program the purpose of which is to impart advice in

the widest sense.

PHONE IN: Involving members of the public expressing their

views either by phone or at a public forum.

SPORT:

Program concerned with any aspect of sports.

TRAVEL:

LEISURE:

JAZZ:

Travel information.

EDUCATE: Educational programs.

DRAMA: All radio plays and serials.

Programs about recreational activities.

Jazz music.

CULTURE: Programs concerning any aspect of national or

COUNTRY: Songs which originate from, or continue the musical

regional culture, including language, theatre, etc.

tradition of the American Southern States.

SCIENCE:

VARIED:

Programs about natural sciences and technology.

NATIONAL: Current popular music of the nation or region in that

country’s language.

Used for mainly speech-based programs like

quizzes, panel games and personality interviews.

OLDIES:

FOLK M:

Music from the so-called “golden age” of popular

music.

POP M:

Commercial music of current popular appeal.

Rock music.

Music which has its roots in the musical culture of a

particular nation.

ROCK M:

M.O.R. M:

Current contemporary music considered to be “easy-

listening.”

DOCUMENT:Program concerning factual matters, presented in an

investigative style.

LIGHT M:

Instrumental music, and vocal or choral works.

CLASSICS: Performances of major orchestral works,

symphonies, chamber music, etc.

OTHER M: Music not fitting into any of the other categories.

WEATHER: Weather reports and forecasts.

Classification of the PTY codes for some FM stations

may be different from the above list.

– 27 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If you are having a problem with your unit, check this list for a possible solution before calling for service.

If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person,

such as your dealer, for service.

Symptom

Cause

Action

Unable to cancel the display demonstration.

Other buttons will pressed to cancel the

display demonstration.

Press CANCEL/DEMO on the unit. (See

page 8.)

No sound is heard.

Connections are incorrect or loose.

Check all connections and make

corrections. (See pages 6 to 8.)

Hard to listen to broadcasts because of

noise.

• Antennas are disconnected.

• Reconnect the antennas correctly and

securely.

• Change the position and direction of the

AM (MW/LW) loop antenna.

• Extend the FM antenna at the best

position.

• The AM (MW/LW) loop antenna is too

close to the unit.

• The FM antenna is not properly extended

and positioned.

The disc sound is discontinuous.

The disc is scratched or dirty.

Clean or replace the disc. (See page 29.)

The disc tray does not open or close.

• The AC power cord is not plugged in.

• Trays are locked.

• Plug the AC power cord.

• Unlock the trays. (See page 18.)

The disc does not play.

The disc is placed upside down.

Place the disc with the label side up.

Turn on the unit.

The cassette holders cannot be opened.

Power supply from the AC power cord has

been cut off while the tape was running.

Impossible to record.

Small tabs on the back of the cassette are

removed.

Cover the holes with adhesive tape.

Operations are disabled.

The built-in microprocessor may

malfunction due to external electrical

interference.

Unplug the AC power cord and then plug it

back in.

Unable to operate the unit from the remote

control.

• The path between the remote control and

the remote sensor on the unit is blocked.

• The batteries are exhausted.

• Remove the obstruction.

• Replace the batteries.

– 28 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

To get the best performance of the unit, keep your discs, tapes, and mechanism clean.

Handling discs

Handling cassette tapes

• Remove the disc from its case by

holding it at the edge while pressing the

center hole lightly.

• Do not touch the shiny surface of the

disc, or bend the disc.

• If the tape is loose in its cassette, take

up the slack by inserting a pencil in

one of the reels and rotating.

• If the tape is loose, it may get

stretched, cut, or caught in the

cassette.

• Put the disc back in its case after use to

prevent warping.

• Be careful not to touch the tape

surface.

• Be careful not to scratch the surface of

the disc when placing it back in its

case.

• Avoid exposure to direct sunlight,

temperature extremes, and moisture.

• Avoid the following places to store the

tape:

— In dusty places

— In direct sunlight or heat

— In moist areas

To clean the disc

Wipe the disc with a soft cloth in a

straight line from center to edge.

— Near a magnet

Cleaning the unit

DO NOT use any solvent — such as conventional

record cleaner, spray, thinner, or benzine — to

clean the disc.

• Stains on the unit

Should be wiped off with a soft cloth. If the unit is

heavily stained, wipe it with a cloth soaked in water

diluted neutral detergent and wrung well, then wipe clean

with a dry cloth.

• Since the unit may deteriorate in quality, become

damaged or get its paint peeled off, be careful about

the followings.

— DO NOT wipe it with a hard cloth.

— DO NOT wipe it strong.

— DO NOT wipe it with thinner or benzine.

— DO NOT apply any volatile substance such as

insecticides to it.

— DO NOT allow any rubber or plastic to remain in

contact with it for a long time.

– 29 –

Download from Www.Somanuals.com. All Manuals Search And Download.

Design and specifications are

subject to change without notice.

Specifications

CA-MXGT91R

CA-MXG71R

Amplifier section

Output Power (IEC 268-3/DIN)

Amplifier section

Output Power (IEC 268-3/DIN)

SUBWOOFERS:

86 W per channel, min. RMS, both channels

SUBWOOFERS:

80 W per channel, min. RMS, both channels

driven into 6 Ω at 63 Hz with no more than

0.9% total harmonic distortion.

driven into 6 Ω at 63 Hz with no more than

0.9% total harmonic distortion.

MAIN SPEAKERS: 21 W per channel, min. RMS, both channels

driven into 6 Ω at 1 kHz with no more than

0.9% total harmonic distortion.

MAIN SPEAKERS: 21 W per channel, min. RMS, both channels

driven into 6 Ω at 1 kHz with no more than

0.9% total harmonic distortion.

Audio input sensitivity/Impedance

(Measured at 1 kHz, with tape recording signal 300 mV)

AUX:

390 mV/50 kΩ

AUX:

390 mV/50 kΩ

Digital output: CD OPTICAL DIGITAL OUTPUT

Signal wave length:

Output level:

660 nm

–15 dBm to –12 dBm

Signal wave length:

Output level:

660 nm

–15 dBm to –12 dBm

Speakers/Impedance:

SUBWOOFERS:

Speakers/Impedance:

SUBWOOFERS:

6 Ω – 16 Ω

MAIN SPEAKERS:

Tuner

FM tuning range:

Tuner

FM tuning range:

87.50 MHz – 108.00 MHz

AM tuning range:

MW: 522 kHz – 1 629 kHz

LW: 144 kHz – 288 kHz

AM tuning range:

MW: 522 kHz – 1 629 kHz

LW: 144 kHz – 288 kHz

CD player

CD capacity:

Dynamic range:

CD player

CD capacity:

Dynamic range:

3 CDs

85 dB

3 CDs

85 dB

Signal-to-noise ratio: 90 dB

Wow and flutter:

Immeasurable

Wow and flutter:

Immeasurable

Cassette deck

Frequency response

Cassette deck

Frequency response

Normal (type I): 50 Hz – 14 000 Hz

Wow and flutter

0.15% (WRMS)

Normal (type I): 50 Hz – 14 000 Hz

Wow and flutter

0.15% (WRMS)

General

Power requirement:

Power consumption:

General

Power requirement:

Power consumption:

AC 230 V

, 50 Hz

AC 230 V

, 50 Hz

160 W (at operation)

140 W (at operation)

20 W (on standby; with power saving off — Normal Mode)

1.1 W (on standby; with power saving on — Ecology Mode)

Dimensions (approx.): 265 mm x 335 mm x 401 mm (W/H/D)

(10⁷/16 in. x 13¹/4 in. x 15¹³/16 in.)

20 W (on standby; with power saving off — Normal Mode)

1.1 W (on standby; with power saving on — Ecology Mode)

Dimensions (approx.): 265 mm x 335 mm x 401 mm (W/H/D)

(10⁷/16 in. x 13¹/4 in. x 15¹³/16 in.)

Mass (approx.):

10.0 kg (22.1 lbs)

Mass (approx.):

10.0 kg (22.1 lbs)

Supplied accessories

See page 6.

Supplied accessories

See page 6.

– 30 –

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTICE/ BEMERKUNG/ AVIS/ OPMERKING/

NOTIS/ HUOMIO/ BEMÆRKE/ AVISO/ AVVISO

English

Svenska

Note on Recording an RDS FM Station

Anmärking angående inspelning av RDS FM-

stationer

If you start recording an FM station while its RDS

information is shown on the display, the RDS information

will be changed and its station frequency, “NO PS,” “NO

PTY” or “NO RT” will appear on the display.

When you finish recording, RDS information will appear

again.

Om en FM-station börjar spelas in när RDS-information

visas på displayen, kommer RDS-informationen att

ändras och dess stationsfrekvens, “NO PS”, “NO PTY”

eller “NO RT” visas på displayen.

När inspelningen avslutats, visas RDS-informationen

igen.

Deutsch

Suomi

Hinweis zur Aufnahme von einem RDS-FM-Sender

Registrering af en FM station med RDS

Wenn Sie die Aufnahme des Programms eines FM-

Senders starten, während die RDS-Information im

Display angezeigt wird, ändert sich die Display-Anzeige,

und es erscheint die Senderfrequenz, “NO PS”, “NO

PTY” der “NO RT”.

Nach Abschluß der Aufnahme erscheint wieder die RDS-

Information.

Hvis man starter registrering af en FM-station mens RDS-

informationen vises på display’et, ændres RDS-

informationen og frekvensen, “NO PS”, “NO PTY” eller

“NO RT” vises på display’et.

Når registreringen afsluttes, vises RDS-informationen

igen.

Français

Dansk

Remarques pour l’enregistrement d’une station FM RDS

Huomautus nauhoittaessasi RDS-FM-aseman

lähetystä

Si vous commencez l’enregistrement d’une station FM

pendant l’affichage des informations RDS, ces

informations disparaissent et sont remplacées par la

fréquence de la station ou les mentions “NO PS”, “NO

PTY” ou “NO RT”.

Jos ryhdyt nauhoittamaan FM-radioaseman lähetystä,

kun RDS-tiedotuksia on näytössä, RDS-tietojen näyttö

peruuntuu ja sen taajuus, “NO PS”, “NO PTY” tai “NO

RT” ilmestyy näyttöön.

Kun nauhoitus päättyy, RDS-tiedotukset palaavat

näyttöön uudelleen.

A la fin de l’enregistrement, les informations RDS

s’affichent à nouveau.

Nederlands

Español

Opmerking bij Opnemen van een RDS FM Station

Nota: cuando grabe de una emisora FM con RDS

Wanneer u een FM station begint op te nemen terwijl de

RDS informatie ervan op het display wordt getoond, zal

de RDS informatie worden veranderd en zal de

frequentie van het bijbehorende station, “NO PS”, “NO

PTY” of “NO RT” op het display verschijnen.

Wanneer u klaar bent met opnemen verschijnt RDS

informatie weer op het display.

Si inicia la grabación de una emisora FM mientras

aparece en pantalla la información RDS, ésta cambiará y

se mostrará la frecuencia, “NO PS”, “NO PTY” o “NO

RT”.

La información RDS volverá a aparecer en pantalla

cuando finalice la grabación.

Italiano

Nota relativa alla registrazione di una stazione FM RDS

Se si comincia a registrare una stazione FM mentre

l’informazione RDS è visualizzata sul display, tale

informazione cambierà. Il display visualizzerà allora la

frequenza della stazione, “NO PS”, “NO PTY” o “NO RT”.

Una volta terminata la registrazione, l’informazione RDS

sarà di nuovo visualizzata sul display.

GV40234-001A

Download from Www.Somanuals.com. All Manuals Search And Download.

VICTOR COMPANY OF JAPAN, LIMITED

0201MWMMDWJEM

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTRUCTIONS

SPEAKER SYSTEM

SP-MXGT91R

BEDIENUNGSANLEITUNG: LAUTSPRECHERSYSTEM

MANUEL D’INSTRUCTIONS: SYSTEME DES ENCEINTES

GEBRUIKSAANWIJZING: LUIDSPREKERSYSTEEM

MANUAL DE INSTRUCCIONES: SISTEMA DE ALTAVOCES

ISTRUZIONI: SISTEMA DI ALTOPARLANTI

BRUKSANVISNING: HÖGTALARSYSTEM

VEJLEDNING: HØJTTALERSYSTEM

KÄYTTÖOHJE: KAIUTINJÄRJESTELMÄ

Thank you for purchasing JVC speakers.

Grazie per aver acquistato questi altoparlanti della JVC.

Before you begin using them, please read the instructions carefully to

be sure you get the best possible performance. If you have any ques-

tions, consult your JVC dealer.

Prima di cominciare l’uso degli altoparlanti, leggete attentamente le

istruzioni per assicurare le migliori prestazioni. Qualora sorgessero

dei dubbi, rivolgetevi al vostro rivenditore JVC.

Vielen Dank für den Kauf dieser JVC-Lautsprecher.

Tack för ditt val av dessa JVC-högtalare.

Lesen Sie bitte diese Bedienungsanleitung vor Ingebrauchnahme

sorgfältig durch, um stets optimale Ergebnisse zu erzielen. Wenden

Sie sich bei etwaigen Fragen bitte an Ihren JVC Händler.

Innan du kopplar in högtalarna i din ljudanläggning bör du för att få

maximala prestanda från högtalarna läsa igenom bruksanvisningen

noggrant. Kontakta din JVC-återförsäljare om du har frågor eller känner

dig osäker.

Nous vous remercions pour l’achat de ces enceintes JVC.

Tak for købet af JVC-højttalerne.

Avant de les utiliser, lire ces instructions avec attention pour en obtenir

les meilleures performances possibles. En cas de questions, con-

sulter votre revendeur JVC.

Gennemlæs venligst vejledningen omhyggeligt før de tages i brug,

så De kan opnå den bedst mulige ydelse. Forhør hos Deres JVC

forhandler hvis De har nogen spørgsmål.

Dank u voor de aanschaf van deze luidsprekers.

Kiitos siitä ettë päädyit valinnassasi JVC-kaiuttimiin.

Lees alvorens over te gaan tot aansluiten, deze gebruiksaanwijzing

door zodat u de best mogelijke prestaties zult verkrijgen. Neem kontakt

op met de JVC dealer indien u vragen heeft.

Ennen kuin alat käyttää niitä, lue käyttöohje huolellisesti, jotta ne

toimisivat parhaalla mahdollisella tavalla. Jos Sinulla on kysyttävää

ota yhteys JVC-edustajaan.

Le estamos muy agradecidos por haber adquirido estos altavoces de

JVC.

Antes de utilizarlos, sirvase leer las instrucciones detenidamente a

fin de obtener el mejor rendimiento posible. Si tienenaluna pregunta,

acuda a su agente de JVC.

— SAFETY INSTRUCTIONS —

“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

This equipment has been designed and manufactured to meet

Switch off using the switch on the equipment and make sure that

international safety standards but, like any electrical equipment, care

must be taken if you are to obtain the best results and safety is to be

assured.

your family know how to do this.

Special arrangements may need to be made for infirm of handi-

capped people.

DON’T use equipment such as personal stereos or radios so that

you are distracted from the requirements of traffic safety. It is illegal

to watch television whilst driving.

Do read the operating instructions before you attempt to use the

equipment.

Do ensure that all electrical connections (including the mains plug,

extension leads and interconnections between pieces of equipment)

are properly made and in accordance with the manufacturer’s

instructions. Switch off and withdraw the mains plug when making or

changing connections.

DON’T listen to headphones at high volume as such use can

permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with

curtains or soft furnishing.

Overheating will cause damage and shorten the life of the equip-

ment.

Do consult your dealer if you are ever in doubt about the installation,

operation or safety of your equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws

— to ensure complete safety always fit the manufacturer’s approved

stand or legs with the fixings provided according to the instructions.

Do be careful with glass panels or doors on equipment.

DON’T continue to operate the equipment if you are in any doubt

about it working normally, or if it is damaged in any way — switch

off, withdraw the mains plug and consult your dealer.

DON’T allow electrical equipment to be exposed to rain or

moisture.

ABOVE ALL

DON’T remove any fixed cover as this may expose dangerous

voltages.

– NEVER let anyone, especially children, push anything into holes,

slots or any other opening in the case.

DON’T leave equipment switched on when it is unattended unless it

is specifically stated that it is designed for unattended operation or

has a standby mode.

– this could result in a fatal electrical shock;

– NEVER guess or take chances with electrical equipment of any

kind

– it is better to be safe than sorry!

GVT0059-003A

[E]

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection

Anschluß

Raccordement

Aansluiting

Conexión

CONNECTION

• DON’T use other amplifier to operate this speaker system

except for CA-MXGT91R.

Collegamento

Ansluiting

Tilslutning

Liitäntä

• Turn off power to the whole system before connecting the

speakers to the amplifier.

• The maximum power handling capacity of the SP-MXGT91R

main speaker is 55 W/Subwoofer is 130 W. Excessive input

will result in abnormal noise and possible damage. In cases

where the signals described below are applied to the speak-

ers, even if the signals are below the maximum allowable in-

put, they may cause an overload and burn the wiring of the

speakers. Be sure to lower the amplifier volume beforehand.

Left speaker

Linker Lautsprecher

Enceinte de gauche

Linker spreker

Altavoz izquierdo

Altoparlante sinistro

Vänster högtalare

Venstre højttaler

Vasen kaiutin

Right speaker

Rechter Lautsprecher

Enceinte de droite

Rechter spreker

Altavoz derecho

Altoparlante destro

Höger högtalare

Højre højttaler

1) Noise during FM tuning.

RED

ROT

Oikea kaiutin

2) High level signals containing high frequency components

produced by a tape deck in the fast forward mode.

3) Click noise produced when turning power of other compo-

nents on and off.

4) Click noise produced when connecting or disconnecting

cords with the power on.

ROUGE

ROOD

ROJO

ROSSO

RÖD

RØD

PUNAINEN

BLACK

SCHWARZ

NOIR

BLACK

SCHWARZ

NOIR

5) Click noise produced when the cartridge is replaced with

the power on.

ZWART

NEGRO

NERO

SVART

SORT

ZWART

NEGRO

NERO

SVART

SORT

6) Click noise produced when operating amplifier switches.

7) Continuous high frequency oscillation or high pitch electroni-

cally produced musical instrument sound.

8) Howling when using a microphones.

MUSTA

BLUE

BLAU

BLEU

BLAUW

AZUL

BLU

BLUE

BLAU

BLEU

BLAUW

AZUL

BLU

BLA

Amplifier output terminals

BLA

Ausgang des Verstärkers

SININEN

Bornes de sortie de l’amplificaterur

Uitgangsaansluitengen van de versterker

Terminales de salida de amplificador

Terminali de uscita dell’amplifcator

Utgångar på förstärkaren

SPECIFICATIONS

Forstærkerudgangsbøsninger

Vahvistimen ulostuloliittimet

Type

: 3-way 3-speaker Bass-Reflex

Type

Dual Giga-Tube Band-Pass

Subwoofers

Speakers

Subwoofer

: 16.0 cm (6-5/16 in.) cone × 1

Main woofer

Tweeter

: 10.0 cm (3-15/16 in.) cone × 1

: 5 cm (2 in.) cone × 1

Power Handling Capacity

Subwoofer

Main Speaker

: 130 W

: 55 W

Impedance

Subwoofer

Main Speaker

: 6 Ω

Frequency Range

Subwoofer

: 30 Hz ~ 120 Hz

Main Speaker

: 75 Hz ~ 29 000 Hz

Sound Pressure Level

Subwoofer

: 78 dB/W·m

(Average of 50 Hz ~ 100 Hz)

Main Speaker

Dimensions (W × H × D)

Mass

: 85 dB/W·m

(Average of 400 Hz ~ 800 Hz)

: 230 mm × 439 mm × 340 mm

(9-1/16 in. × 17-5/16 in. × 13-7/16 in.)

: 7.2 kg (15.9 lbs) each

Design and specifications subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

ANSCHLUSS

RACCORDEMENT

• Verwenden Sie zum Betrieb dieses Lautsprechersystems keinen

anderen Verstärker, ausgenommen CA-MXGT91R.

• NE PAS utiliser d’autre amplificateur que le CA-MXGT91R pour

faire fonctionner les enceintes.

•

Schalten Sie vor dem Anschluß der Lautsprecher an den Verstärker

die Spannungsversorgung des gesamten Systems aus.

• Mettre hors circuit tout le système avant de raccorder les

enceintes à l’amplificateur.

•

Die

maximale

Belastbarkeit des SP-MXGT91R-

• La puissance maximale admissible par le haut-parleur principal

du SP-MXGT91R est de 55 W, celle admissible par le haut-

parleur d’extrêmes graves est de 130 W.

Hauptlautsprechers ist 55 W und die des Subwoofers ist 130 W.

Eine Überlastung führt zu Verzerrungen und möglicherweise zu

Beschädigungen.

Signale der unten beschriebenen Art

En dépassant la puissance admissible, cela provoquera des

bruits anormaux et détériorera les enceintes.

können, auch wenn sie unter dem maximal zulässigen Eingang

liegen, eine Überlastung verursachen und die

Lautsprecherwicklungen durchbrennen. Verringern Sie vorher

die Lautstärke des Verstärkers.

Au cas où les signaux décrits ci-dessous sont envoyés aux

enceintes, et même si ces signaux sont inférieurs à la puis-

sance d’entrée maximum admissible, ils risquent de provoquer

une surcharge ou même un incendie. S’assurer de bien diminuer

le volume sonore de l’amplificateur.

1) Geräusche beim Einstellen von UKW-Sendern.

2) Hochpegelige Signale mit Hochfrequenz-Anteilen, die von

Tonbanddecks beim Schnellvorspulen erzeugt werden.

3) Klickgeräusche, wenn die Spannungsversorgung anderer

Komponenten ein-und ausgeschaltet wird.

4) Klickgeräusche, wenn Kabel angeschlossen oder abgetrennt

werden, während die Spannungsversorgung eingeschaltet ist.

1) Parasites durant une syntonisation FM.

2) Signaux de niveau élevé contenant des composants à haute

fréquence, comme ceux générés par une platine

d’enregistrement en mode avance rapide.

3) Cliquetis se produisant lorsque d’autres appareils sont mis

en ou hors circuit.

4) Cliquetis se produisant lorsque des appareils sont branchés

ou dé-branchés alors que leur alimentation est en circuit.

5) Klickgeräusche, wenn der Tonabnehmer des Plattenspielers

ausgewechselt wird, während die Spannungsversorgung

eingeschaltet ist.

6) Klickgeräusche, die beim Betätigen von Schaltern des

Verstärkers erzeugt werden.

5) Cliquetis se produisant lorsque la cellule d’une platine tourne-

disque est changée alors que l’alimentation est en circuit.

7) Ständige Hochfrequenzschwingungen oder elektronisch

erzeugte Töne von Musikinstrumenten mit hohen Tonhöhen.

6) Cliquetis se produisant lorsque les commandes de

l’amplificateur sont manipulées.

8) Rückkopplungen von Mikrofonen.

7) Oscillations continuelles à haute fréquence ou sons très aigus

provenant d’instruments de musique électroniques.

8) Hurlements dus à l’utilisation de micros.

CARACTÉRISTIQUES

TECHNISCHE DATEN

Type

: Enceinte 3 voices, 3 haut-

parleurs type à réflexion des

basses

Dual Giga-Tube Band-Pass

Subwoofers

Typ

: 3-Weg, 3-Lautsprecher-

Baßreflexbox

Dual Giga-Tube Band-Pass

Subwoofers

Lautsprecher

Subwoofer

Hauptwoofer

Hochtöner

Belastbarkeit:

Subwoofer

Hauptlautsprecher

Impedanz:

Subwoofer

Hauptlautsprecher

Frequenzbereich:

Subwoofer

Hauptlautsprecher

Schalldruckpegel:

Subwoofer

Haut-parleurs

Extrêmes graves

Principal

Aigus

Puissance maximale admissible

Haut-parleur d’extrêmes graves : 130 W

Haut-parleur principal

Impédance

Haut-parleur d’extrêmes graves : 6 Ω

Haut-parleur principal

Bande passante

Haut-parleur d’extrêmes graves : 30 Hz–120 Hz

Haut-parleur principal

Pression sonore

Haut-parleur d’extrêmes graves : 78 dB/W·m (Moyenne de

50 Hz à 100 Hz)

Haut-parleur principal

: 16.0 cm Konus × 1

: 10.0 cm Konus × 1

: 5 cm konus × 1

: conique de 16.0 cm × 1

: conique de 10.0 cm × 1

: conique de 5 cm × 1

: 130 W

: 55 W

: 6 Ω

: 30 Hz bis 120 Hz

: 75 Hz bis 29 000 Hz

: 75 Hz–29 000 Hz

: 78 dB/W·m (Durchschnitt von

50 Hz bis 100 Hz)

: 85 dB/W·m (Durchschnitt von

400 Hz bis 800 Hz)

Hauptlautsprecher

: 85 dB/W·m (Moyenne de

400 Hz à 800 Hz)

: 230 mm × 439 mm × 340mm

: 7,2 kg chaque

Abmessungen (B × H × T) : 230 mm × 439 mm × 340mm

Gewicht : Je 7,2 kg

Dimensions (L × H × P)

Masse

Présentation et caractéristiques modifiables sans préavis.

Technische Änderungen vorbehalten.

Download from Www.Somanuals.com. All Manuals Search And Download.

AANSLUITINGEN

CONEXIÓN

• Gebruik GEEN andere versterker dan de CA-MXGT91R om dit

• NO utilice ningún otro amplificador para operar este sistema de

luidsprekersysteem aan te sturen.

altavoces excepto CA-MXGT91R.

• Schakel de spanning van alle aangesloten komponenten uit

• Desactive la alimentación de todo el sistema antes de conectar

alvorens de luidsprekers met de versterker te verbinden.

los altavoces al amplificador.

• Het maximale vermogen van de SP-MXGT91R hoofdluidspreker

is 55 W en van de subwoofer 130 W. Te hoge ingang kan in

abnormale geluidsreproduktie en in beschadigingen resulteren.

• La capacidad máxima de potencia del altavoz principal del

SP-MXGT91R es de 55 W y la del altavoz de subgraves es de

130 W.

Overbelasting en verbranding van de bedrading kan worden

veroorzaakt, wanneer de hieronder beschreven signalen naar

de luidspekers worden gevoed, zelfs wanneer de signalen onder

het maximaal toegestane ingangsvermogen zijn. Verminder

eerst het volume van de versterker.

Uná entrada excesiva resultará en ruido anormal y posibles

daños.

En casos donde las señales descritas más abajo se apliquen a

los altavoces, aunque las mismas resulten menores que la

entrada máxima permisible, pueden causar una sobrecarga y

quemar el cableado de los altavoces. Asegúrese de disminuir

el volumen del amplificador con anterioridad.

1) Ruis, zoals dit optreedtijdens afstemming op een FM-zender.

2) Hoogfrekwentie signalen van een hoog niveau, zoals die

tijdens het vooruitspoelen van een tapedeck worden

geproduceerd.

3) Klikkende geluiden, die worden veroorzaakt door het in - en

uitschakelen van de netspanning van andere komponenten.

4) Klikkende geluiden, zoals die worden geproduceerd bij het

tot stand brengen of verbreken van aansluitingen terwijl de

netspanning is ingeschakeld.

1) Ruido durante la sintonia en FM.

2) Señales de alto nivel que contengan componentes de alta

frecuencia producidos por un magnetófono en el modo de

avance rápido.

3) Ruidos de conmutación provocados al encender y apagar

otros componentes.

4) Ruido de conmutación al conectar o desconectar cables con

los componentes encendidos.

5) Ruido de conmutación cuando se reemplaza la cápsula con

los componentes encendidos.

5) Klikkende geluiden, zoals die optreden bij het vervangen van

het element van een draaitafel terwijl de netspanning is

ingeschakeld.

6) Klikkende geluiden, zoals die worden geproduceerd door

bediening van de schakelaars van de versterker.

6) Ruido de conmutación provocados por la operación de los

selectores del amplificador.

7) Voortdurende hoogfrekwentie-oscillatie, of hoogtonige,

7) Continua oscilación de alta frecuencia o de sonidos de tonos

altos provocados por instrumentos electrónicos.

8) Aullidos a utilizar micrófonos.

elektronisch

geproduceerde

geluiden

van

muziekinstrumenten.

8) Rondzingend geluid bij gebruik van mikrofoons.

ESPECIFICACIONES

TECHNISCHE GEGEVENS

Tipo

: Reflex bajo con 3-altavoces y 3 vias

Dual Giga-Tube Band-Pass

Subwoofers

Type

: 3-weg 3-luidsprekers 4 bass reflex

Dual Giga-Tube Band-Pass

Subwoofers

Altavoces

De subgraves

Principal

De agudos

Capacidad de potencia

De subgraves

Principal

Luidsprekers

Subwoofer

Hoofdwoofer

Tweeter

Maximale vermogen

Subwoofer

Hoofdluidspreker

: Tipo cónico de 16.0 cm × 1

: Tipo cónico de 10.0 cm × 1

: Tipo cónico de 5 cm × 1

: 16.0 cm kegeltype × 1

: 10.0 cm kegeltype × 1

: 5 cm kegeltype × 1

: 130 W

: 55 W

: 130 W

: 55 W

Impedancia

De subgraves

Principal

Impedantie

Subwoofer

Hoofdluidspreker

: 6 Ω

Gama de frecuencias

De subgraves

Principal

Frekwentiebereik

Subwoofer

Hoofdluidspreker

: 30 Hz–120 Hz

: 75 Hz–29 000 Hz

: 30 Hz–120 Hz

: 75 Hz–29 000 Hz

Nivel de presión acústica

De subgraves

Geluidsdrukniveau

Subwoofer

: 78 dB/W·m

(Gemiddeld 50 Hz–100 Hz)

: 85 dB/W·m

(Promedio de 50Hz–100Hz)

: 85 dB/W·m

Principal

Hoofdluidspreker

(Promedio de 400Hz–800Hz)

Dimensiones (An × Al × Prf) : 230 mm × 439 mm × 340mm

Peso : 7,2 kg cada uno

(Gemiddeld 400 Hz–800 Hz)

: 230 mm × 439 mm × 340mm

: Elk 7,2 kg

Afmetingen (B × H × D)

Gewicht

Veranderingen in technische gegevens et ontwerp onder

voorbehpoud.

El diseño y las especificaciones están sujetos a cambio sin aviso.

Download from Www.Somanuals.com. All Manuals Search And Download.

COLLEGAMENTO

ANSLUTNING

• NON usare un amplificatore diverso dal modello CA-MXGT91R

per utilizzare questo sistema di altoparlanti.

• Använd INTE någon annan förstärkare än CA-MXGT91R till att

driva detta högtalarsystem med.

• Spegnete la corrente dell’intero sistema prima di collegare gli

altoparlanti all’amplificatore.

• Slå av strömmen i alla apparater i ljudanläggningen innan

högtalarna ansluts till förstärkaren.

• La capacità di potenza massima dell’altoparlante principale del

modello SP-MXGT91R è di 55 W e quella del subwoofer è di

130 W. Un ingresso eccessivo causerà un suono anormale è

possibili danni.

Nel caso in cui i segnali descriti qui sotto vengono applicati agli

altoparlanti, possono causare un sovraccarico e bruciare il

cablaggio degli altoparlanti, anche se i segnali siano al di sotto

dell’ingresso massimo ammesso.

• Maximal effekthanteringskapacitet för SP-MXGT91R är 55 W

för huvudhögtalare/130 W för lågbashîgtalare. Brus uppstår i

ljudet och högtalarna kan skadas om de matas med för hög

effekt. I situationerna som beskrivs nedan kan högtalarna också

överbelastas och kabeltråden inne i hägtalarna brännas sönder,

fastän högtalarnas effekt inte har överskridits.

Sänk därför ljudstyrkan på förhand.

1) Brus under inställning av FM-radiostationer.

2) Starka, högfrekventa signaler från ett kassettdäck under

snabbspolning framåt.

Assicuratevi di diminuire il livello del volume dell’altoparlante

prima di procedere.

1) Generazione di rumore durante la sintonizzazione FM.

3) Ljudbangar som uppstår när andra apparater i anläggningen

slås till och från.

4) Skrapljud som uppstår när anslutningskablar ansluts eller

kopplas från medan strömmen är på.

2) Segnali di alto livello che contengono dei componenti ad alta

frequenza riprodotti da una piastra a cassette nel modo di

avanzamento rapido.

3) Si senitrà uno scatto quando accendete o spegnete la corrente

degli altri compoenti.

5) Skrapljud som uppstår när pickupelementet på en skivspelare

byts medan strömmen är på.

4) Si sentirà uno scatto quando collegate o scollegate i cavi con

la corrente accesa.

6) Ljudbangar som uppstår när du använder förstärkarens

omkopplare.

5) Si sentirà uno scatto quando viene sostituita la cartuccia con

la corrente accesa.

7) Kontinuerliga, högfrekvenssvängningar eller högfrekvent ljud

från elektroniska musikinstrument.

6) Si sentirà uno scatto quando vengono usati gli interruttori

dell’amplificatore.

8) Akustisk återkoppling (tjutande ljud) vid bruk av mikrofoner.

7) Oscillazione continua ad alta frequenza o suoni acuti da

strumenti musicali elettronici.

8) Ululato quando usate i microfoni.

SPECIFICAZIONI

TEKNISKA DATA

Tipo

: Reflex basso con 3-altoparlanti e 3

vie

Typ

: 3-vägs, 3-elements

basreflexhögtalare

Dual Giga-Tube Band-Pass

Subwoofers

Dual Giga-Tube Band-Pass

Subwoofers

Altoparlanti

Subwoofer

Högtalarelement

Lågbaselement

: Cono da 16.0 cm × 1

: 16.0 cm kon × 1

Woofer principale

Tweeter

Capacità di potenza

Subwoofer

: Cono da 10.0 cm × 1

Huvudbaselement

Diskantelement

Effekthanteringskapacitet

Lågbashögtalare

Huvudhögtalare

: 10.0 cm kon × 1

: Cono da 5 cm × 1

: 5 cm kon × 1

: 130 W

: 55 W

Altoparlante principale : 55 W

Impedenza

Impedans

Subwoofer

Altoparlante principale : 6 Ω

: 6 Ω

Lågbashögtalare

Huvudhögtalare

: 6 Ω

Gamma di frequenza

Subwoofer

Altoparlante principale : 75 Hz–29 000 Hz

Frekvensomfång

Lågbashögtalare

Huvudhögtalare

: 30 Hz–120 Hz

: 75 Hz–29 000 Hz

Livello di pressione sonora

Ljudtrycksnivå

Subwoofer

: 78 dB/W·m

Lågbashögtalare

: 78 dB/W·m

(Gamma di frequenza: 50–100 Hz)

(50–100 Hz i genomsnitt)

Altoparlante principale : 85 dB/W·m (Gamma di frequenza:

400–800 Hz)

Huvudhögtalare

: 85 dB/W·m

(400–800 Hz i genomsnitt)

: 230 mm × 439 mm × 340mm

: 7,2kg perst.

Dimensioni (L × A × P)

: 230 mm × 439 mm × 340mm

: 7,2 kg ciascuno

Yttermått (B × H × D)

Vikt

Massa

Il disegno e le specificazioni sono soggetti a cambiamenti senza

preavviso.

Rätt till ändringar av utförande och specifikationer förbehålles utan

föregående meddelande.

Download from Www.Somanuals.com. All Manuals Search And Download.

TILSLUTNING

LIITÄNTÄ

• Anvend IKKE anden forstærker end CA-MXGT91R til drift af

dette højttalersystem.

• ÄLÄ käytä muuta vahvistinta tämän kaiutinjärjestelmän käyttöön

paitsi mallille CA-MXGT91R.

• Sluk for strømmen til hele systemet før højttalerne forbindes til

forstærkeren.

• Katkaise koko järjestelmän virta ennen kuin suoritat liitännät

kaiuttimista vahvistimeen.

• Den maksimale belastningskapacitet for SP-MXGT91R

hovedhøjttaleren er 55 W/for subwooferen 130 W.

For kraftigt indgangssignal vil resultere i unormal stoj og muligvis

beskadigelse.

I tilfælde hvor højttalerne udsættes for signalerne beskrevet

nedenfor, kan der forekomme overbelastning og overbrænding

af ledningerne i höjttalerne selv om signalstyrken er under den

maksimale tilladte værdi. Husk derfor at at sænke

højttalerlydstyrken i forvejen.

• Mallin SP-MXGT91R pääkaiuttimen enimmäisteho on 55 W,

apubassokaiuttimen 130 W. Liiallinen antoteho aiheuttaa

epänormaalia kohinaa ja jopa vahinkoa.

Tapauksissa, missä kaiuttimet joutuvat alla kuvattujen signaalien

kohteeksi, vaikka signaalit olisivat alle sallitun maksimi

antotehon, ne saattavat aiheuttaa ylikuormitusta ja polttaa

kaiuttimien johdot.

Vähennä siis vahvistimen äänenvoimakkuutta jo ennalta.

1) Kohinaa FM-virityksen aikana.

1) Støj under FM-afstemning.

2) Kasettidekistä eteenpäinkelauksen aikana muodostuneet

vahvat, korkeataajuuksisia komponentteja sisältävät signaalit.

3) Klik-ääni, joka syntyy silloin kun toisten osien virta kytketään

ja katkaistaan.

2) Signaler med høje niveauer der indeholder höjfrekvente

komponenter dannet af en båndoptager der er indstillet til

hurtig fremspoling.

3) Klikstøj dannet når der tændes eller slukkes for strommen til

4) Klik-ääni, joka syntyy silloin kun kytketään tai irrotetaan johtoja

virran ollessa päällä.

andre domponenter.

4) Klikstøj der dannes når ledninger tilsluttes eller tages ud af

forbindelse mens der er tændt for strømmen.

5) Klik-ääni, joka syntyy silloin kun vaihdetaan hylsy virran ollessa

päällä.

5) Klikstøj der dannes når pickuppen udskiftes mens der er tændt

for strømmen.

6) Klik-ääni, joka syntyy silloin kun käytetään vahvistimen

kytkimiä.

6) Klikstøj der dannes når forstærkerens omskiftere betjenes.

7) Fortsat høj frekvenssvingning, eller en højlyd dannet af et

elektronisk instrument.

7) Jatkuva korkea värähtely tai elektronisesti tuotettu korkea

soittimen ääni.

8) Ulinaa mikrofonia käytettäessä.

8) Hyletoner når der anvendes en mikrofon.

SPECIFIKATIONER

TEKNISET TIEDOT

Type

: 3-vejs basrefleks-højttaler

med 3-elementer

Dual Giga-Tube Band-Pass

Subwoofers

Tyyppi

: 3-tie, 3 kaiuttimen bassorefleksi

Dual Giga-Tube Band-Pass

Subwoofers

Kaiuttimet

Apubasso

: 16,0 cm karitomuotoinen × 1

Højttalere

Subwoofer

Hoved-bashøjttaler

Diskantenhed

Belastningskapacitet

Subwoofwer

Hovedhøjttaler

Impedans

Subwoofwer

Hovedhøjttaler

Frekvensområde

Subwoofwer

Hovedhøjttaler

: 16.0 cm membran × 1

: 10.0 cm membran × 1

: 5 cm membran × 1

Pääbasso

Diskantti

Enimmäisteho

Apubasso

Pääkaiutin

Impedanssi

Apubasso

Pääkaiutin

Taajuusala

Apubasso

Pääkaiutin

: 10,0 cm karitomuotoinen × 1

: 5,0 cm karitomuotoinen × 1

: 130 W

: 55 W

: 130 W

: 55 W

: 6 Ω

: 30 Hz–120 Hz

: 75 Hz–29 000 Hz

: 30 Hz–120 Hz

: 75 Hz–29 000 Hz

Äänenpainetaso

Apubasso

: 78 dB/W·m

(Keskimäärin 50 Hz–100 Hz)

: 85 dB/W·m

Lydtryksniveau

Subwoofwer

: 78 dB/W·m (Gennemsnit på

50 Hz–100 Hz)

Pääkaiutin

(Keskimäärin 400 Hz–800 Hz)

: 230 mm × 439 mm × 340 mm

: 7,2 kg perst.

Hovedhøjttaler

: 85 dB/W·m (Gennemsnit på

400 Hz–800 Hz)

: 230 mm × 439 mm × 340mm

: 7,2 kg hver

Mitat (L × K × S)

Paino

Mål (B × H × D)

Vægt

Oikeudet muutoksiin pidätetään.

Design og specifikationer kan blive ændret uden varsel.

EN. GE. FR. NL. SP. IT. SW. DA. FI.

XXXXX

0101JYMPRIJEM

VICTOR COMPANY OF JAPAN, LIMITED

Download from Www.Somanuals.com. All Manuals Search And Download.

IOGear Switch GCS1732 User Manual
JBL Speaker TLX PS10 User Manual
John Lewis Clothes Dryer JLDV 02 User Manual
JVC Stereo Receiver LVT0178 001A User Manual
Jwin MP3 Player JX CD530 User Manual
Kawasaki Automobile Accessories 70Z IV 2 User Manual
Kenwood Computer Monitor KVT 815DVD User Manual
Kettler Bicycle Accessories DVP721VR 00 User Manual
Keys Fitness Fitness Equipment KPS SPC User Manual
Kompernass Waffle Iron KH 1162 User Manual