CD PORTABLE SYSTEM
RD-T70RBU
RD-T50RLB
SNOOZE
/DIMMER
SLEEP
STANDBY/ON
1
4
2
5
3
6
7
8
9
10
+10
REPEAT
TUNER
BAND
CD
FM MODE
BASS/TREBLE
AHB PRO
VOLUME
REMOTE CONTROL RM-SRDT7A
[RD-T70RBU Only]
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0931-005A
[B]
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been disigned and manufactured to meet international safety standards but, like any electrical equipment,
care must be taken if you are to obtain the best results and safety is to be assured.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of
equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug
when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch
off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended opera-
tion or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is
illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s
approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result
in a fatal electrical shock.;
— NEVER guess or take chances with electrical equipment of any kind
— it is better to be safe than sorry!
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for purchasing the JVC CD Portable System.
We hope it will be a valued addition to your home as well as to your outdoor life, giving you years of enjoyment.
Be sure to read this instruction manual carefully before operating your new stereo system.
In it you will find all the information you need to set up and use the system.
If you have a query that is not answered by the manual, please contact your dealer.
Features
Here are some of the things that make your System both powerful and simple to use.
I The controls and operations have been redesigned to make them very easy to use, freeing you to just enjoy the music.
•
With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio, or CD Player with
a single touch. (When power is supplied from AC)
I The System incorporates AHB (Active Hyper Bass) PRO circuitry to faithfully reproduce low frequency sounds.
[RD-T70RBU Only]
I A 45-station preset capability 30 FM and 15 AM (MW) in addition to auto-seek and manual tuning.
I A user-friendly timer lets you wake or fall asleep to music.
I The CD Player can play back a CD-R and CD-RW.
How This Manual Is Organized
•
Basic information that is the same for many different functions - e.g. setting the volume - is given in the section ‘Common Operations’,
and not repeated under each function.
•
•
•
The names of buttons/controls are written in all capital letters: e.g. TUNER BAND.
If the button names on the Unit and the Remote Control are the same, the description on which the button is used will be omitted.
System functions are written with an initial capital letter only: e.g. Normal Play.
Use the table of contents to look up specific information you require.
We’ve enjoyed making this manual for you, and hope it serves you in enjoying the many features built into your System.
IMPORTANT CAUTIONS
1. Where to place the Unit
I
•
•
•
Select a place which is level, dry and neither too hot nor too cold (between 5°C and 35°C).
Leave sufficient distance between the Unit and a TV.
Do not use the Unit in a place subject to vibrations.
2. Power cord
I
•
•
•
Do not handle the power cord with wet hands!
Some power is always consumed as long as the power cord is connected to the wall outlet.
When unplugging the Unit from the wall outlet, always pull the plug, not the power cord.
3. Malfunctions, etc.
I
•
There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.
•
Do not insert any metallic object into the System.
I Carefully read “CAUTION” on page G-1.
I Rating label is placed on the exterior of the bottom.
Table of Contents
II
Features ............................................................................... 1
How This Manual Is Organized .......................................... 1
IMPORTANT CAUTIONS ................................................ 1
Specifications.......................................... Back cover
Getting Started.......................................................... 2
Common Operations................................................ 3
Using the Tuner ........................................................ 5
Using the CD Player ................................................. 8
Using the Timers .................................................... 10
Care And Maintenance........................................... 12
Troubleshooting ......................................Back cover
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
II
Accessories
Check that you have all of the following items, which are supplied with the System.
Power Cord (1)
Remote Control (1) [RD-T70RBU Only]
Batteries for Remote Control (2) [RD-T70RBU Only]
If any of these items are missing, contact your dealer immediately.
How To Put Batteries
How To Put Batteries In the Unit
1. Open the battery cover on the back of the Unit by pulling it toward you while pressing the tabs as shown by the arrows.
2. Put 3 memory backup batteries R6P(SUM-3)/AA(15F) (not supplied) in the battery compartment in the order of “1” to “3”.
3. Put 6 batteries R20/D (13F) (not supplied) in the battery compartment in the order of “1” to “6” as shown.
4. Securely close the battery cover.
Note: When you operate your Unit on mains (AC) power, the power source switches automatically from batteries to AC. However, you should
remove the batteries when operating on AC power.
1
2
2
3
3
5
1
6
4
“R6P (SUM-3) / AA (15F)” size batteries
“R20/D (13F)” size batteries
How To Put Batteries In the Remote Control [RD-T70RBU Only]
Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.
R6P(SUM-3)/AA(15F)
CAUTION: Handle batteries properly.
To avoid battery leakage or explosion:
•
•
•
•
•
Remove batteries when the Unit or the Remote Control will not be used for a long time.
When you need to replace the batteries, replace batteries at the same time with new ones.
Do not use an old battery with new ones.
Do not use different types of batteries together.
Do not try to recharge non-rechargeable batteries.
Dispose of batteries in the proper manner, according to federal, state, and local regulations.
Using the Remote Control [RD-T70RBU Only]
The Remote Control makes it easy to use many of the functions of the Unit from a distance of up to 7m (23 feet) away.
You need to point the Remote Control at the remote sensor on the Unit’s front panel.
Note: If you point the Remote Control from the slant direction, the above distance will be shortened.
Remote sensor
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AC Power Cord
Firmly insert the AC power cord supplied with the System into the AC inlet on the back of the Unit.
CAUTIONS:
•
ONLY USE THE JVC POWER CORD PROVIDED WITH THIS SYSTEM IN
ORDER TO AVOID MALFUNCTION OR DAMAGE TO THE SYSTEM.
BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN
GOING OUT OR WHEN THE SYSTEM IS NOT IN USE FOR AN EXTEND-
ED PERIOD OF TIME.
AC IN
•
Plug the AC power cord into the wall outlet, and your System is at your
command!
Common Operations
II
Display
SNOOZE
/DIMMER
SLEEP
STANDBY/ON
SNOOZE
/DIMMER
1
4
2
5
3
6
STANDBY/ON
7
8
9
MULTIJOG
CLOCK/DISPLAY
STANDBY indicator
VOLUME
10
+10
REPEAT
VOLUME control
(Jog dial)
CD PORTABLE SYSTEM RD-T70R
STANDBY/ON
CLOCK/
DISPLAY
RANDOM/
REPEAT
BASS/
TREBLE
SLEEP
TUNER
BAND
CD
AHB PRO
STANDBY
BASS/TREBLE
AHB PRO
[RD-T70RBU Only]
FAVORITE
TIMER
TIMER1 TIMER2
STANDBY/ON
FM MODE
MULTI CONTROL
MANUAL/
PRESET TUNING
BASS/TREBLE
AHB PRO
SNOOZE
DIMMER
CD
TUNER BAND
AUTO PRESET
AHB PRO
VOLUME +, –
BASS/TREBLE
VOLUME
SNOOZE/DIMMER
[RD-T70RBU]
SNOOZE
[RD-T50RLB]
REMOTE CONTROL RM-SRDT7A
[RD-T70RBU Only]
PHONES
“GOOD BYE” is displayed and the display becomes blank, except
for the clock display. The STANDBY indicator lights up.
Turning the Power On and
Standby
I When in Standby mode, the Unit continues to a small amount of
power to run the display.
I To switch off the Unit completely, unplug the AC power cord
from the AC outlet.
Turning the Unit On ————————
Press the
button.
When power is supplied from the batteries:
STANDBY/ON
STANDBY/ON
When the Unit is turned off with the
button on the Unit (the
button on the Remote Control is ineffective), the display be-
comes blank and the STANDBY indicator lights up.
or
STANDBY
I
To switch off the Unit completely, remove the batteries from the Unit.
The STANDBY indicator goes out and the display come on, and
“WELCOME” is displayed.
The Unit comes on ready to continue in the mode it was in when the
power was last turned off.
I For example, if the last thing you were doing was listening to a
CD, you are now ready to listen to a CD again. If you wish, you
can change to another source.
I If you were listening to the Tuner last, the Tuner comes on play-
ing the station it was last set to.
Adjusting the Volume
You can adjust the volume level between MIN (0) and MAX (32)
when the Unit is turned on.
Turn the VOLUME control on the Unit to the right
or left to increase or decrease the volume level.
OR
Note: When power is supplied from the batteries, the
button
Press the VOLUME + or – button on the Re-
mote Control to increase or decrease the
volume level.
on the Remote Control does not work.
Turning the Unit Standby —————
Press the
button again.
When operating on AC power:
STANDBY/ON
STANDBY/ON
CAUTION: DO NOT turn on the Unit and/or start
playing any source without first setting the
VOLUME control to MIN (0) , as a sudden blast of
sound can damage your hearing.
or
STANDBY
3
Download from Www.Somanuals.com. All Manuals Search And Download.
For private listening
Adjusting the dimmer level:
Connect a pair of headphones to the PHONES jack. No sound
(On the Unit only)
comes out of the speakers.
Be sure to turn down the volume before connecting or putting on
headphones.
1. With the Unit turned on, press and hold the DIMMER button
on the Unit until “DIMMER:XX” appears on the display.
2. Turn the Jog dial and adjust the dimmer level between 1 and 16.
3. Press the DIMMER button.
Reinforcing the Bass Sound
(AHB PRO) [RD-T70RBU Only]
When operated on batteries ————
When the Unit is turned on, you can turn on the backlighting of the
display for a few seconds.
Each time you press the SNOOZE/DIMMER button, the backlight
turns on for a few seconds.
You can reinforce the bass sound to maintain rich, full bass at low
volume:
To get the effect, press the AHB (Active Hyper Bass) PRO button.
The “BASS” indicator lights up on the display.
To cancel the effect, press the button again.
The “BASS” indicator goes out.
Using Batteries
Power Batteries (6 pcs.):
You can operate the System on batteries. When the batteries are
exhausted, “NO BATT” will appear on the display. In this case, re-
place with the new batteries.
Tone Control (BASS/TREBLE)
You can control the tone by changing the bass and treble.
Memory Backup Batteries (3 pcs.):
Your settings such as the preset stations, clock and timer are backed
up with this batteries.
1. Press the BASS/TREBLE button until “BASS”
Ior “TREBLE” appears on the display.
Each time you press the button, the display changes as follows:
BASS =TREBLE =original display =(back to the beginning)
CAUTION:
If memory backup batteries are exhausted or not
installed, and the AC power cord is disconnected
or there is a power failure, the settings you have
made will be erased from memory in approx. half
a day.
2. Turn the Jog dial on the Unit or press the
IVOLUME +/– button on the Remote Control
to adjust the level.
The bass or treble level changes between –6 and +6. (0: Flat)
To exit the tone control mode, press the BASS/TREBLE but-
ton until the original display appears, or wait for 15 seconds.
To forcibly reset the bass and treble levels to 0 (FLAT),
press the BASS/TREBLE button for 2 seconds or more.
Showing the Time (CLOCK/
DISPLAY)
While listening to a CD or the radio, you can see the current time.
To display the clock, press the CLOCK/DISPLAY button on the
Unit.
To return to the original display, press the same button until
the original display appears.
Note: You need to set the clock first in order for it to work. (See
“Setting the Clock” on page 10.)
Adjusting the Brightness
(DIMMER) [RD-T70RBU Only]
When operated on AC power ———
You can switch the brightness of the display’s backlighting (full
light and dimmed light). In addition, the dimmed backlighting
brightness can be changed in 16 steps.
When the Unit is turned on:
Each time you press the SNOOZE/DIMMER button, the backlight
fully turns on or dims.
When the Unit is turned off (Standby):
Each time you press the SNOOZE/DIMMER button, the backlight
dims or turns off.
When the Sleep Timer is on:
You can also dim or turn off the backlight with the SNOOZE/DIM-
MER button.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
II
SNOOZE
/DIMMER
MULTIJOG
SLEEP
STANDBY/ON
VOLUME
1
4
2
5
3
6
CD PORTABLE SYSTEM RD-T70R
STANDBY/ON
CLOCK/
DISPLAY
RANDOM/
REPEAT
BASS/
TREBLE
SLEEP
AHB PRO
I
MANUAL/PRE-
STANDBY
FAVORITE
TIMER
TIMER1 TIMER2
SET TUNING
CLOCK/DISPLAY
Number keys
7
8
9
MULTI CONTROL
¢
4
MANUAL/
PRESET TUNING
10
+10
REPEAT
SNOOZE
DIMMER
CD
TUNER BAND
AUTO PRESET
TUNER
BAND
CD
TUNING BAND
AUTO PRESET
TUNER BAND
FM MODE
4
¢
BASS/TREBLE
AHB PRO
Band display, Frequency display, Preset channel
RDS indicator
VOLUME
REMOTE CONTROL RM-SRDT7A
[RD-T70RBU Only]
(Display when using the Tuner)
You can listen to FM and AM (MW) stations. Stations can be tuned
in manually, automatically, or from preset memory storage.
3. Select a station using one of the following
Imethods.
Note that the possible operation is limited by the Tuning mode
you have selected in step 2.
I Manual Tuning (In Manual Tuning mode)
Press the 4or ¢button repeatedly to move from frequency
to frequency until you find the station you want.
Setting the Antenna
For FM reception:
Extend the built-in wire antenna to obtain the best reception.
MULTI CONTROL
MANUAL/
PRESET TUNING
or
OR
I Auto Tuning (In Manual Tuning mode)
If you press and hold the 4or ¢button for one second or
more, the frequency changes down, or up, automatically until a
station is found.
For AM reception:
Turn the Unit to obtain the best reception.
OR
I Preset Tuning using the Unit (Possible only after pre-
setting stations) (In Preset Tuning mode)
Press the 4or ¢button to select the preset station.
After you have selected the preset number, the band and the fre-
quency are displayed.
One Touch Radio (AC power only)—
Just press the TUNER BAND button to turn on the Unit and start
playing the station you were last tuned to.
I You can also switch from the CD Player to the radio by pressing
the TUNER BAND button.
•
Example:Press the 4or ¢button until the preset num-
ber 12 “P- 12” appears.
Tuning In a Station
1. Press the TUNER BAND button.
I
OR
The Band and Frequency you were last tuned to appear on the
display.
Each time you press the button, the band changes as follows:
I Preset Tuning using the Remote Control (Possible
only after presetting stations)
Select the station by entering its preset number on the number
keys.
FM AUTO
FM MONO
AM
•
•
Example:For channel 5, press 5. For channel 15, press +10
then 5. For channel 25, press +10 twice, then 5.
For channel 30, press +10 twice, then 10.
2. Press the 7button on the Unit to select the
Ituning mode (Manual or Preset).
The band and the frequency are displayed.
Each time you press the button, the tuning mode changes as fol-
lows:
MANUAL (Manual Tuning mode) ÔPRESET (Preset Tuning
mode)
MULTI CONTROL
MAAL/
PRESEUNING
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Presetting (Using the Re-
Presetting Stations
mote Control) [RD-T70RBU Only] ——
You can preset up to 30 FM stations and up to 15 AM (MW) stations
into memory.
TUNER
BAND
Number key(s)
(hold for 2 seconds)
MAAL/
PRESEUNING
Auto Presetting (Using the Unit) —
In each band, you can automatically preset FM-30, AM (MW)-15 sta-
tions. Preset numbers will be allocated as stations are found, starting
from the station currently tuned to and moving up the frequency.
(On the Unit)
1. Select a band by pressing the TUNER
IBAND button.
(Band select)
(Auto preset)
(for 2 seconds)
TUNER BAND
AUTO ESET
TUNER BAND
AUTO SET
2.Press the 7button on the Unit until “MAN-
IUAL (Manual Tuning mode)” appears on the
display.
4
¢
3. Press the
or
button to tune in a station.
I
1. Select a band (AM or FM) by pressing the
ITUNER BAND button.
4. Set the preset number by pressing and hold-
Iing the number key on the Remote Control
2. Press the TUNER BAND button for more
Ithan 2 seconds.
until “STORED” appears on the display.
•
To preset numbers 1 to 10: Press the number key and hold
it down for 2 seconds.
“AUTO” appears, and then auto presetting starts.
•
To preset numbers 11 to 19: Press the +10 button, then
press the second number key (1 to 9) and hold it down for 2
seconds.
To preset numbers 21 to 29: Press the +10 button twice,
then press the second number key (1 to 9) and hold it down
for 2 seconds.
3. Repeat steps 1-2 for the other band.
I
I If you want to change any of the auto preset stations, follow the
procedure for Manual Presetting.
•
•
CAUTION: To prevent the preset stations from being
erased because of a power failure, etc., install mem-
ory backup batteries in the System.(See page 2.)
Otherwise, they will be erased in approx. half a day.
To preset number 30: Press the +10 button twice, then press
and hold 10 button.
Example: Preset number = 12
Manual Presetting (Using the Unit) —
(Station Select)
MULTI CONTROL
TUNER BAND
AUTO ESET
MANUAL/
MAAL/
PRESET TUNING
PRESEUNING
5. Repeat steps 2 - 4 for further presetting.
To change the preset stations, repeat the same steps as above.
I
(
Preset No. Select
)
(Press & hold )
(for 2 sec)
MULTI CONTROL
MAAL/
MAAL/
MANUAL/
PRESET TUNING
To Change the FM
Reception Mode
PRESENING
PRESEUNING
The “STEREO” indicator lights up and you can hear stereo effects,
when a program is broadcast in stereo.
1. Select a band by pressing the TUNER
IBAND button.
However if an FM stereo broadcast is hard to receive or noisy, you
can select Monaural mode. Reception improves, but you lose any
stereo effect.
2. Press the 7button until “MANUAL (Manual
ITuning mode)” appears on the display.
Press the TUNER BAND button to select FM
MONO mode.
3. Press the 4or ¢button to tune in a sta-
Ition.
The “MONO” indicator lights up on the display.
To restore the stereo effect, press the TUNER BAND button
to select FM Auto mode. The “MONO” indicator goes out.
4. Press the 7button for 2 seconds or more.
I
The preset number and band/frequency are alternately
displayed for 5 seconds.
5. Within 5 seconds, repeatedly press the 4or
I
¢button until the preset number you want
appears, then press and hold the 7button
until “STORED” appears on the display.
6. Repeat steps 2-5 for further presetting.
I
To change the preset stations, repeat the same procedure as
above.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PS (Program Service):
Receiving FM Stations with
RDS
While searching, “WAIT PS” and “PS” alternately appear on the
display. Then, the RDS indicator lights up and the station name ap-
pears. “NO PS” appears if no signal is sent.
You can use the RDS (Radio Data System) by using the CLOCK/
DISPLAY button on the Unit.
Clock:
Current time appears on the display.
Station Frequency:
Station frequency (non-RDS service)
RDS allows FM stations to send additional signals with their regular
program signals. For example, the stations send their station names,
and information about what type of program they broadcast, such as
sports or music, etc. However, this unit can only receive the follow-
ing type of RDS signal:
PS (Program Service):
shows commonly known station names.
Notes:
• If searching finishes at once, “WAIT PS” and “PS” will not ap-
pear on the display.
• RDS is not available for AM (MW) broadcasts.
To show the RDS signals on the
On characters displayed
When the display shows PS signals:
• The display shows upper case letters only.
• The display cannot show accented letters; For example, “A” may
represent accented “A’s” like “Á, Â, Ã, À, Ä and Å”.
display ———————————————
Press the CLOCK/DISPLAY button on the Unit while lis-
tening to an FM station.
Each time you press the button, the display changes to show infor-
mation in the following order:
CLOCK/
DISPLAY
PS
Clock
Frequency
[Example of characters displayed]
!
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
II
CD cover
(including the display)
SNOOZE
SLEEP
/DIMMER
STANDBY/ON
1
4
2
5
3
6
MULTIJOG
VOLUME
Number keys
REPEAT
7
8
9
CD PORTABLE SYSTEM RD-T70R
STANDBY/ON
CLOCK/
DISPLAY
Jog dial
RANDOM/
REPEAT
BASS/
TREBLE
SLEEP
AHB PRO
10
+10
REPEAT
STANDBY
FAVORITE
TIMER
TIMER1 TIMER2
7
TUNER
BAND
CD
MULTI CONTROL
¢
4
MANUAL/
CD 38
¢
PRESET TUNING
FM MODE
SNOOZE
DIMMER
CD
TUNER BAND
AUTO PRESET
BASS/TREBLE
AHB PRO
CD 38
7
4
VOLUME
0(CD OPEN/CLOSE)
Playing time, Preset number
Track number
REMOTE CONTROL RM-SRDT7A
[RD-T70RBU only]
Random/Repeat indicator
(Display when using the CD Player)
You can use Normal, Random, or Repeat Play. Repeat Play can be
set to repeat all or just one of the tracks on the CD.
4. Press the CD 38 button.
The first track of the CD begins playing.
I
The CD Player automatically stops when the last track of the CD has
finished playing.
One Touch CD Player
(AC power only) ——————————
•
During playback, the track number being played and the play-
back time elapsed are shown on the display.
Track number
I Just press the CD 38button.
•
The power is automatically turned on. If a CD is already
inserted, “CD” is displayed and the CD will start playing
from the first track.
•
If no CD is inserted, “NO DISC” is displayed on the dis-
play and the CD Player remains in Stop mode.
Playback time elapsed
To stop playing the CD, press the 7button.
The following information for the CD is displayed.
Total number of tracks
Normal Play
1. Press the 0button on the Unit.
I
The CD cover (including the display) opens.
2. Place a CD, with its label side up.
I
Total playback time
To pause, press the CD 38.
To cancel pause, press the CD 38 again. Play continues from
the point where it was paused.
Notes:
•
•
You can place an 8 cm (3'') CD without an adaptor.
If the CD cannot be read correctly (because it is scratched, for
example), “0 0:00” appears on the display.
Skip Play (4 or ¢) ————————
During playback, press the 4or ¢button to select the
track you want.
3. Press the 0button again to close the CD
Icover.
The selected track starts playing.
•
To close the CD cover and directly start playback, omit this
•
•
Press the ¢button to go forward one track at a time.
Press the 4button to go back to the beginning of the current
track. To go back to the previous track, quickly press the 4
button twice.
step and go to the next step.
CAUTION: Avoid getting your hand caught in the
CD cover.
I You can also skip the tracks in Stop mode.
Search Play —————————————
During playback, hold down the 4 or ¢ button.
This operation will fast forward/backwards the CD so you can
quickly find a particular passage in the track you are listening to (the
CD playback speed will increase in two steps).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Locating a Track directly with the
Remote Control ——————————
Using the number keys on the Remote Control, you can go directly
to the beginning of any track.
During playback, enter the number of the track you want
to listen to using the number keys.
The selected track starts playing.
2.Press the CD 38 button.
I
Repeat playback starts.
To stop Repeat Play, press the I button.
To cancel Repeat Play mode, in Stop mode, press the REPEAT
button until the Repeat indicator goes out, or press the I button.
Pressing the 0button to open the CD cover will also cancel Repeat
Play mode.
•
Example: For track 5, press 5. For track 15, press +10, then 5.
For track 20, press +10, then 10. For track 32, press +10 three
times, then 2.
RANDOM Play
The tracks will play in no special order when you use this mode.
(On the Unit)
1. In Stop mode, press the RANDOM/REPEAT
Ibutton until the “RANDOM” indicator alone
lights up on the display.
Each time you press the button, the Random/Repeat indicator
changes as follows.
P =P ALL =P RANDOM = RANDOM (Random
Play mode) =blank display =(back to the beginning)
2. Press the CD 38 button.
I
All the tracks are played back in random order once, then the
CD stops.
•
During playback, skip play and search play can be done in the
similar manner as for Normal Play mode, using the 4or ¢
button.
To stop Random Play, press the I button.
To cancel Random Play mode, in Stop mode, press the RAN-
DOM/REPEAT button until the “RANDOM” indicator goes out, or
press the I button. Pressing the 0button to open the CD cover will
also cancel Random Play mode.
Repeat Play
One track or all the tracks on a CD will play repeatedly when you
use this mode.
(On the Unit)
1. In Stop mode, press the RANDOM/REPEAT
Ibutton.
Each time you press the button, the Random/Repeat indicator
changes as follows.
P = P ALL = P RANDOM = RANDOM = blank
display =(back to the beginning)
P :
Will repeat one track.
P ALL:
P RANDOM:
Will repeat all the tracks.
Will repeat all the tracks in random order.
2. Press the CD 38 button.
I
Repeat playback starts.
To stop Repeat Play, press the I button.
To cancel Repeat Play mode, in Stop mode, press the RAN-
DOM/REPEAT button until the Random/Repeat indicator goes out,
or press the I button. Pressing the 0button to open the CD cover
will also cancel Repeat Play mode.
(On the Remote Control) [RD-T70RBU Only]
1. In Stop mode, press the REPEAT button.
I
Each time you press the button, the Repeat indicator changes as
follows.
P = P ALL =blank display =(back to the beginning)
P :
Will repeat one track.
P ALL: Will repeat all the tracks.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
II
SNOOZE
/DIMMER
SNOOZE
/DIMMER
SLEEP
STANDBY/ON
SLEEP
1
4
2
5
3
6
7
8
9
MULTIJOG
VOLUME
SLEEP
10
+10
REPEAT
CD PORTABLE SYSTEM RD-T70R
STANDBY/ON
CLOCK/
TUNER
BAND
CD
Jog dial
RANDOM/
REPEAT
BASS/
TREBLE
DISPLAY
SLEEP
AHB PRO
STANDBY
FAVORITE
TIMER
TIMER1 TIMER2
CLOCK/DISPLAY
TIMER 1
FM MODE
MULTI CONTROL
MANUAL/
PRESET TUNING
BASS/TREBLE
AHB PRO
TIMER 2
SNOOZE
DIMMER
CD
TUNER BAND
AUTO PRESET
VOLUME
SNOOZE/DIMMER
[RD-T70RBU]
SNOOZE
REMOTE CONTROL RM-SRDT7A
Timer 2 indicator
Timer 1 indicator
[RD-T50RLB]
SLEEP indicator
[RD-T70RBU Only]
(Display when using the Timer)
You can enjoy timer settings with the unique dual timer, consisting
of the Timer 1 and Timer 2. These Timers can independently select
a playback source from the CD player (Normal Play or Random
Play), Tuner, or 8 melodies. For example, you can make up to a mel-
ody every morning with the Timer 1, and without changing the Tim-
er 1 setting, you can listen to the favorite program by reserving it
with the Timer 2. Also, you can use the Sleep Timer to fall asleep
to music. Your System automatically turns off after a certain length
of time.
3. Press the CLOCK/DISPLAY button.
I
The minute digits blink.
4. Turn the Jog dial to set the minute.
I
5. Press the CLOCK/DISPLAY button.
I
“CLOCK OK” appears for 2 seconds. The selected time is set
and the seconds start counting from 0.
Setting the Timer
CAUTION: If memory backup batteries are ex-
hausted or not installed, and the AC power cord is
disconnected or there is a power failure, time set-
tings will be erased from memory in approx. half
a day. Then, the display blinks “0:00”. If this hap-
pens, set the current time (clock) and perform the
timer setting again.
The Timer 1 or Timer 2 is turned on at the set time and the System
turns on. The selected source is played and the volume fades in. The
System will automatically turn off in 1 hour.
The setting procedure for the Timer 1 and Timer 2 is identical.
Notes:
• Perform each setting step within 30 seconds. Otherwise, setting is
cleared and the procedure must be repeated from the beginning.
• Tuner timer uses the preset station. So, you need to preset the sta-
tions in Preset Tuning mode beforehand. See, “Presetting Sta-
tions” on page 6.
Setting the Clock
When the Unit is operated on AC power or batteries for the first
time, the time indication “0:00” will blink on the display and you
need to set the clock.
(On the Unit: While the Unit is turned on)
You can set the clock whether the Unit is turned on or off (Standby)
if the AC power is supplied to the Unit.
Notes:
• The clock must be correctly set for the timer to work.
• The clock may gain or lose 1 to 2 minutes per month.
• Perform each setting step within 30 seconds. Otherwise, setting is
cleared and the procedure must be repeated from the beginning.
1. Press the TIMER1 or TIMER2 (we write as
ITIMER1/2 hereafter) button.
The current hour digits blink. Also, the Timer 1/2 indicator
(
TIMER1/2) blinks.
Note:
•
If the clock is not set yet, “CLOCK SET” is displayed and the
Unit enters the clock setting mode. In this case, set the clock
referring to “Setting the Clock” on this page.
MULTIJOG
MULTIJOG
VOLUME
VOLUME
CLOCK/
CLOCK/
CLOCK/
DISPLAY
DISPLAY
DISPLAY
2. Turn the Jog dial to select the hour.
I
3. Press the TIMER1/2 button.
I
(for 3 sec)
The current minute digits blink.
(On the Unit)
4. Turn the Jog dial to select the minute.
I
1. Press the CLOCK/DISPLAY button for 3 sec-
Ionds or more.
5. Press the TIMER1/2 button.
I
The current source name blinks.
The hour digits blink.
2. Turn the Jog dial to set the hour.
I
10
Download from Www.Somanuals.com. All Manuals Search And Download.
To cancel the timer, press the TIMER1/2 button to turn off the
Timer 1/2 indicator ( TIMER1/2).
To reactivate the timer, repeatedly press the TIMER1/2 button
until the Timer 1/2 indicator ( TIMER1/2) remains lit again.
6. Turn the Jog dial to select the source.
I
The source name changes as follows:
CD
TUNER
MELODY
To confirm the timer settings, repeatedly press the TIMER1/2
button.
To change the timer settings, repeat the setting procedure
from the beginning.
7. Press the TIMER1/2 button and select a
Isource item you want.
When the source is CD:
Tip:
1. Turn the Jog dial to select either “TRACK NO” (for
The timer works even if the Unit is turned on. So, while listening to
a CD or radio, you can use the timer to know the set time. For ex-
ample, if you are listening to the radio, you can set the timer so that
the melody will be played at the set time, instead of the radio. In this
case, the playback sound slowly fades in.
Normal Play) or “RANDOM” (for Random Play).
2. Press the TIMER1/2 button.
When “TRACK NO” is selected, “TRACK- 1” blinks.
Go to steps 3 and 4.
When “RANDOM” is selected, the current volume lev-
5-Minute Snoozing (SNOOZE)
el blinks. Go to step
(When “TRACK- 1” blinks.)
.
8
When the Timer 1/2 turns on, if you wish, you can activate 5-minute
snoozing function to temporarily stop playing source.
While the timer is activating, press the
SNOOZE button.
3. Turn the Jog dial to select another track, if you want.
4. Press the TIMER1/2 button.
The current volume level blinks. Go to step
.
8
The Unit turns off for 5-minute for snoozing. (The Timer 1/2 blinks.)
Notes:
Pressing and holding the SNOOZE button for more than 2 seconds
cancels the timer.
The maximum number of times to repeat snoozing is limited to 10.
Snooze function does not work when the other timer is used.
When the source is TUNER:
1. Turn the Jog dial to select FM AUTO, FM MONO, or
•
AM.
2. Press the TIMER1/2 button.
•
•
The preset number blinks. (e.g. “P-1”)
3. Turn the Jog dial to select the preset number you want
to listen to.
Setting the SLEEP Timer
Use the Sleep Timer to turn the Unit off after a certain number of
minutes when it is playing. By setting the Sleep Timer, you can fall
asleep to music and know that your Unit will turn off by itself rather
than play all night.
4. Press the TIMER1/2 button.
The current volume level blinks. Go to step
.
8
When the source is MELODY:
The current melody number (1 - 8) blinks and the melody is
I You can only set the Sleep Timer when the Unit is on and a
source is playing.
played.
1. Turn the Jog dial to select one of melodies.
1. Play back a CD or tune in to a desired sta-
Ition.
2. Press the TIMER1/2 button.
The current volume level blinks. Go to step
.
8
2. Press the SLEEP button.
I
8.Turn the Jog dial to set the volume level.
I
The “SLEEP” indicator blinks.
The volume level changes between “MIN (0)” and “MAX
(32)”.
3. Set the length of time you want the source
Ito play before shutting off.
9. Press the TIMER1/2 button.
I
•
Each time you press the SLEEP button, it changes the num-
The TIMER1/2 is set and the Timer 1/2 indicator
ber of minutes shown on the display in this sequence:
10 =20 =30 =60 =90 =120 =Cancelled =(back to
the beginning)
(
TIMER1/2) remains lit.
10
. Prepare the music source according to the
Isource set in step 6.
The “SLEEP” indicator will stop blinking after 5 seconds and re-
mains on (The backlight dims.). Then, the display returns to the one
before you set the Sleep Timer.
The Unit is now set to turn off after the number of minutes you have
set.
CD: Load a CD.
TUNER/MELODY:No preparation is necessary.
•
If no CD is loaded with the CD source selected, the MEL-
ODY 1 will be activated instead of a CD.
To Confirm the Sleep Time
Press the SLEEP button once. The remaining sleep time is dis-
played, and after 5 seconds, the original display returns.
11. Turn off the Unit (Standby mode).
I
When the set time comes —————
To Cancel the SLEEP Timer Setting
Press the SLEEP button until the “SLEEP” indicator goes off on the
display. Turning off the Unit also cancels the SLEEP Timer.
When the set time comes, the Unit automatically turn on and plays
the source. During this time, the Timer 1/2 indicator (
Timer 1/2)
blinks. The timer will automatically turn off in 1 hour. In case that the
source is CD, the Unit automatically turns off when playing back all
the tracks is finished.
•
To temporarily cancel the timer, press the TIMER 1/2 but-
ton once or change the volume with the VOLUME control
on the Unit or the VOLUME +/- button on the Remote
Control. Then the Timer 1/2 indicator (
TIMER 1/2)
remains lit. (When the source is CD or TUNER, pressing
any button on the Unit cancels the timer.)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Care And Maintenance
II
Compact Discs
Handle your CDs carefully, and they will last a long time.
•
Only CDs bearing these marks can be played
with this Unit.
Recordable
ReWritable
•
Continued use of irregularly shaped CDs
(heart-shape, octagonal, etc.) can damage the
Unit.
•
•
Remove the CD from its case by holding it at
the edges while pressing the case's center hole
lightly.
Do not touch the shiny surface of the CD, or
bend the CD.
•
•
•
Put the CD back in its case after use to prevent
warping.
Be careful not to scratch the surface of the CD
when placing it back in the case.
Avoid exposure to direct sunlight, temperature
extremes, and moisture.
•
A dirty CD may not play correctly. If a CD is
dirty, wipe it with a soft cloth in a straight line
from center to edge.
CAUTION: Do not use any solvent (for example,
conventional record cleaner, spray thinner, ben-
zine, etc.) to clean a CD.
Moisture Condensation
Moisture may condense on the lens inside the Unit in the following
cases:
•
•
•
After turning on heating in the room.
In a damp room.
If the Unit is brought directly from a cold to a warm place.
Should this occur, the Unit may malfunction. If this happens, leave
it turned on for a few hours until the moisture evaporates, unplug the
AC power cord, and then plug it in again.
General Notes
To ensure top performance, keep your CDs and the mechanism clean.
•
Store CDs in their cases, and keep them in cabinets or on
shelves.
•
Keep the CD cover closed when not in use.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have a problem with your System, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as your
dealer, for service.
II
•
•
Symptom
Possible Cause
Action
Connect it firmly
No sound is heard.
•
•
The power cord is disconnected.
The batteries in the Unit have lost
their charge.
•
•
Replace the batteries.
•
Headphones are connected.
•
Disconnect the headphones.
Poor AM reception
Poor FM reception
The System is not properly positioned.
Turn the System to the best reception
position.
The FM antenna is not properly posi-
tioned.
Extend the FM antenna and turn it to the
best reception position.
The CD skips.
The CD is dirty or scratched.
Clean or replace the CD.
The CD does not play.
The CD is upside down.
Put the CD in with the label side up.
Preset tuning is not possible with the
4/¢key.
Manual Tuning mode is selected.
Press the I button on the Unit until
“PRESET” is displayed.
Manual tuning is not possible with the
4/¢key.
Preset Tuning mode is selected.
Press the I button on the Unit until
“MANUAL” is displayed.
Unable to operate the Remote Control.
•
•
The path between the Remote Control
and the sensor on the Unit is blocked.
The batteries have lost their charge.
•
Remove the obstruction.
•
Replace the batteries.
Operations are disabled.
The built-in microprocessor has malfunc-
tioned due to external electrical interference.
Unplug the Unit then plug it back in.
Specifications
Amplifier
Output Power
(Max.) 5 W (2.5 W + 2.5 W) at 4 ohms
(10% THD) 4 W (2 W + 2 W) at 4 ohms
Output Sensitivity/Impedance (1 kHz)
Phones 32 ohms - 1 kohm
0 mW - 20 mW/ch output into 32 ohms
II
Speakers
8 cm ✕ 2, 4 ohms
General
Dimensions 438 mm ✕ 175.5 mm ✕ 261.5 mm
(W/H/D)
Mass Approx. 2.5 kg (without batteries)
Accessories
CD Player
Power Cord (1)
Remote Control (RM-SRDT7) (1)
[RD-T70RBU Only]
Signal-To-Noise Ratio 90 dB
Wow And Flutter Unmeasurable
Batteries for Remote Control R6 (SUM-3)
/AA (15F) (2) [RD-T70RBU Only]
Tuner
FM Tuner
Tuning Range 87.5 MHz - 108.0 MHz
AM Tuner
Tuning Range (MW) 522 kHz - 1,629 kHz
Antenna Built-in wire antenna for FM
Built-in ferrite core antenna for AM
Power Specifications
Power Requirements AC 230 V ~ , 50 Hz
Power Consumption 10 watts (power on mode)
1.8 watts (in Standby mode)
Design and specifications are subject to change without notice.
VICTOR COMPANY OF JAPAN, LIMITED
EN
0402HMOCREHIT
Download from Www.Somanuals.com. All Manuals Search And Download.
|