JVC Portable CD Player LVT2190 006A User Manual

CD PORTABLE SYSTEM  
CHAINE PORTABLE A CD  
NX-PB10  
For Customer Use:  
INSTRUCTIONS  
Enter below the Model No. and  
Serial No. which are located  
either on the rear, bottom or  
side of the cabinet. Retain this  
information for future reference.  
Model No.  
MANUEL D’INSTRUCTIONS  
Serial No.  
LVT2190-006A  
[J]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes on using iPod  
Contents  
• Be sure to reduce the volume on the System to the  
minimum level before connecting iPod. Adjust the  
volume after starting playback.  
• You cannot send any data to the iPod from the System.  
• Do not carry the System with iPod connected. It might  
cause damage to the dock or you might drop the iPod.  
• Do not touch or hit the iPod terminal pins or connector  
pins in the iPod dock directly. Doing so might cause  
damage to the connector pins.  
• iPod is charged through the dock when the System is  
turned on.  
• Information shown on the display differs depending on  
the type of the iPod.  
Introduction....................................................... 2  
Precautions.................................................................................... 2  
Playable disc/file types.............................................................. 2  
Notes on using USB mass storage class device................ 2  
Notes on using iPod ................................................................... 3  
Notes on using SD card............................................................. 3  
Getting started .................................................. 4  
Preparing FM antenna............................................................... 4  
Connecting power cord............................................................ 4  
Preparing remote control......................................................... 4  
Basic operation .................................................. 5  
Using headphones...................................................................... 5  
• If iPod does not play correctly, update iPod software to  
the latest version. For details about updating iPod, check  
on the Apple web site <http://www.apple.com>.  
Common operations.......................................... 6  
Setting the clock.......................................................................... 6  
Locking disc/iPod door ............................................................. 6  
Sleep Timer.................................................................................... 6  
Daily Timer..................................................................................... 7  
Sound adjustment ...................................................................... 7  
Changing display information................................................ 7  
Compatible iPod models  
• iPod nano (2nd, 3rd, 4th, 5th and 6th generation)  
• iPod nano  
• iPod touch (2nd, 3rd and 4th generation)  
• iPod touch  
• iPod (4th generation)  
• iPod classic  
• iPod photo (4th generation)  
• iPod video (5th generation)  
• iPod mini (2nd generation)  
• iPod mini  
Playback operations.......................................... 8  
iPod................................................................................................... 8  
Disc/USB/SD.................................................................................. 8  
FM radio........................................................................................10  
External device...........................................................................11  
References........................................................12  
Troubleshooting ........................................................................12  
Maintenance ...............................................................................13  
Specifications..............................................................................13  
Notes on using SD card  
• DO NOT insert any object other than an SD card into the  
insertion slot.  
• DO NOT use a cracked or deformed SD card.  
• Make sure that SD card playback has stopped before  
removing the SD card. Otherwise, the data may be  
damaged.  
• Never insert an SD card upside down. Otherwise, it will  
not be able to be removed.  
• When you play a miniSD™/microSD™ card, be sure to  
attach the miniSD™/microSD™ adaptor to the card  
before insertion.  
CAUTION: Proper Ventilation  
To avoid risk of electric shock and fire, and to prevent  
damage, locate the apparatus as follows:  
1. Front: No obstructions and open spacing.  
2. Sides/Top/Back: No obstructions should be placed  
in the areas indicated by the dimensions in the  
illustration.  
• You can use an SD card of up to 32 GB.  
3. Bottom: Place on the level surface. Maintain an  
adequate air path for ventilation by placing on a  
stand with a height of 10 cm or more.  
Front view  
Side view  
15 cm  
15 cm  
(5-15/16˝)  
(5-15/16˝)  
15 cm  
15 cm  
(5-15/16˝)  
(5-15/16˝)  
15 cm  
(5-15/16˝)  
10 cm  
10 cm  
(3-15/16˝) (3-15/16˝)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting started  
Preparing FM antenna  
Preparing remote control  
Extend the FM antenna so that you can obtain the best  
When you use the remote control for the first time, pull out  
reception.  
the insulation sheet.  
FM antenna  
To replace the battery in the remote control  
• Make sure the antenna conductor does not touch any  
other terminals, connecting cords or the power cord.  
Also, keep the antenna away from metallic parts of  
the System, connecting cords, and the AC power cord.  
Otherwise, it could cause poor reception.  
Caution  
Danger of explosion if battery is incorrectly replaced.  
Replace only with the same or equivalent type.  
Connecting power cord  
Be sure to connect the power cord to wall outlet after all  
• Store the battery in a place where children cannot reach.  
If a child accidentally swallows the battery, consult a  
doctor immediately.  
other connections have been made.  
• To prevent the battery from overheating, cracking, or  
starting a fire:  
– Do not recharge, short, disassemble or heat the  
battery or dispose of it in a fire.  
– Do not leave the battery with other metallic materials.  
– Wrap the battery with tape and insulate when  
throwing away or saving it.  
To wall outlet  
– Do not poke the battery with tweezers or similar tools.  
• Dispose of battery in the proper manner, according to  
federal, state, and local regulations.  
Set the clock before using this System (see page 6).  
• The battery (battery pack or battery installed) shall not  
be exposed to excessive heat source such as sunshine,  
fire or the like.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operation  
STANDBY lamp  
Remote sensor  
Turn on the power.  
Select a source.  
1
2
3
Adjust the volume.  
• To turn off the power, press  
.
1 2 3  
DO NOT turn off the System with the  
volume set to an extremely high level;  
otherwise, the sudden blast of sound  
may damage your hearing, speakers,  
and headphones when you turn on the  
System or start playback.  
1
2
• When the System is turned off with  
the volume set to over “17,the volume  
level is automatically set to “16next  
time you turn on the System.  
3
Using headphones  
Connect headphones (not supplied) to the  
jack using a  
stereo mini plug cord (not supplied).  
Be sure to turn down the volume before connecting or  
putting on the headphones.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common operations  
Setting the clock  
Sleep Timer  
You can set the clock only when the System is turned off  
You can set Sleep Timer only when the System is turned  
(on standby).  
on.  
Show the clock setting display.  
Show the Sleep Timer setting display.  
1
1
(Hold)  
(Hold)  
Adjust the hour and minute.  
Specify the shut-off time.  
2
2
(Canceled)  
• The clock may gain or lose 1 to 2 minutes per  
month. You may need to readjust the clock  
periodically.  
• To check the remaining time until the System shuts off,  
press and hold CLOCK/SLEEP.  
• To check the current time while the System is turned on,  
press CLOCK/SLEEP.  
• If there is a power failure, the clock loses its settings. You  
need to set the clock again.  
Locking disc/iPod door  
You can lock the disc/iPod door to prevent it from opening  
by accident.  
While the disc/iPod door is closed...  
On the main unit:  
(Hold at the same time)  
(Scrolled on the display)  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Daily Timer  
Sound adjustment  
By using Daily Timer, you can wake up with your favorite  
music.  
• Prepare the playback source beforehand.  
Fade Muting  
You can drop the volume in a moment.  
Show the Daily Timer setting display.  
1
• To restore the volume, press again or adjust the volume.  
(Hold)  
Timer setting item is displayed.  
Hyper Bass Sound (HBS)  
You can reinforce the bass sound.  
Set the timer contents.  
You can set the following items:  
2
Canceled  
(No indication)  
ON TIME Hour and minute for the on-time  
OFFTIME Hour and minute for the off-time  
SOURCE  
Playback source  
• “A-INis not available.  
Sound mode  
1 Select the setting item.  
You can select the sound mode suitable for your favorite  
music.  
2 Start setting the selected item.  
3 Set the item.  
Canceled (No indication)  
• To set hour and minute: Press ¢ or 4, then  
TIMER.  
• To set the source: Press CD 6, iPod 6, USB  
6, SD 6, or FM/AUDIO IN, then TIMER.  
– When you select “TUNER,press ¢ or 4 to  
select preset number.  
Changing display information  
You can display ID3/WMA tag information during playback  
of MP3/WMA.  
• To correct a misentry, wait for a while until the  
setting procedure is canceled, then repeat the  
procedure from step to change the setting.  
1
• When no operation is done for a while during  
setting Daily Timer, the setting procedure is  
canceled.  
• When “ID3 ONis selected, ID3/WMA tag information is  
displayed.  
Activate Daily Timer.  
3
4
The timer indicator ( ) lights up.  
Turn off the System.  
• To cancel a Daily Timer, press TIMER while the System is  
turned on. The timer indicator ( ) disappears.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback operations  
iPod  
Disc/USB/SD  
Connecting an iPod device  
Placing a disc  
Press 0 to open the disc/iPod door, then connect an iPod.  
Press 0 to open the disc/iPod door, then put a disc into  
the holder.  
• Take the iPod protect case off before connecting.  
• Connect the iPod firmly.  
• To close the disc/iPod door, press 0.  
– Do not close the disc/iPod door with the iPod dock  
leaning toward you.  
• When placing a disc, be sure to place a disc with the  
label side facing forward.  
• See page 3 for more about connecting an iPod.  
• To close the disc/iPod door, press 0.  
• When placing or removing a disc, take enough care not  
to fall the System down.  
Playback operations  
Connecting a USB mass storage class  
device  
• To play back/pause an iPod: Press iPod 6.  
• To select a track: Press ¢ or 4.  
• To fast-forward a track: Press and hold ¢.  
• To fast-reverse a track: Press and hold 4.  
• To put iPod in sleep mode: Press and hold iPod 6.  
• Sound distortion may occur when playing back audio  
sources with high recording levels. If distortion occurs,  
it is recommended to turn off the equalizer of iPod. For  
information on operating the iPod, see the instruction  
manual for iPod.  
• See page 2 for more about connecting a USB mass  
storage class device.  
Inserting an SD card  
Menu operations  
To display the menu/to go back to the previous menu  
To select an item on the menu  
• When removing the SD card, push it in and then pull it  
out.  
• See page 3 for more about inserting an SD card.  
• Depending on the type of the iPod, you can operate the  
menu only on the screen of the iPod.  
• Operate iPod touch itself in the following cases:  
– When operating the home button.  
– When selecting application icons on the home screen.  
– When dragging the slider.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback operations  
Program Play  
To play a disc  
Select a source and stop playback.  
1
To play a USB mass storage  
class device  
Show the program setting display.  
2
To play an SD card  
• To play back/pause a disc: Press CD 6.  
• To play back/pause a USB mass storage class device:  
Press USB 6.  
• To play back/pause an SD card: Press SD 6.  
• To select a track: Press ¢ or 4.  
• To fast-forward a track: Press and hold ¢.  
• To fast-reverse a track: Press and hold 4.  
• To select a group (MP3/WMA only): Press or .  
• To stop playback: Press 7.  
Select a track number.  
For audio CD:  
3
For MP3/WMA: Select a group (1), then select a track  
(2).  
1
Repeat Play  
2
• You can select up to 32 tracks.  
Canceled  
(No indication)  
(MP3/WMA only)  
Start program play.  
4
Repeats the current track.  
Repeats all tracks.  
REPEAT1  
REPEAT  
Repeats all tracks in the current group  
(MP3/WMA only).  
REPEAT  
FOLDER  
• To erase the entire program, press 7 while playback is  
stopped.  
Random Play  
Canceled (No indication)  
Playback starts in a random order.  
• Random Play ends when all tracks have been played.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playback operations  
FM radio  
Searching for stations  
Improving the reception  
If an FM stereo broadcast is hard to listen to, you can  
improve the reception by switching to monaural mode.  
Press FM/AUDIO IN repeatedly to select  
“FMas the source.  
1
• When the monaural mode (FM MONO) is activated, the  
reception is improved. However, the stereo effect is lost.  
• To restore stereo reception, press FM/AUDIO IN  
repeatedly to select “FM.”  
– The ST indicator lights up when receiving stereo  
broadcast.  
Start searching.  
2
(Hold)  
The station search stops when a station of sufficient  
signal strength is found.  
• To manually stop the search, press or .  
• When you press or repeatedly, the frequency  
changes step by step.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
External device  
Connecting an external device  
Presetting stations  
Connect an external device using a stereo mini plug cord  
(not supplied).  
You can preset up to 20 FM stations.  
Show the preset number while listening  
to a target station.  
1
Playing an external device  
The preset number flashes.  
Press FM/AUDIO IN repeatedly to select “A–INas the  
source, then start playback of the connected external  
device.  
Select a preset number.  
2
Store the preset station.  
3
Tuning in to a preset station  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
References  
Troubleshooting  
If you are having a problem with your System, check this list for a possible solution before calling for service.  
Symptoms  
Causes/Remedies  
Power does not come on.  
• Power plug is not inserted securely. Plug it in securely.  
• There is a time limit. Start the procedure again.  
Adjustments or settings are suddenly  
canceled before you finish.  
Unable to operate the System from the  
remote control.  
• The path between the remote control and the remote sensor on  
the System is blocked.  
• The battery is exhausted.  
No sound is heard.  
• Headphones are connected.  
Hard to listen to broadcasts because of  
noise.  
• The FM antenna is not properly extended and positioned.  
• Electrostatic discharge from your body may cause noise. If this  
happens, turn the System off then on again.  
The iPod does not play, but “IPODappears • The iPod battery is low or exhausted. Charge the iPod battery.  
on the display.  
The disc/USB mass storage class device/SD • The disc is placed incorrectly. Place the disc with the label side  
card does not play.  
facing forward.  
• The disc is recorded using “packet writing (UDF file system).It  
cannot be played.  
• The USB mass storage class device is not connected properly or  
the SD card is not inserted properly.  
• The CD-R/CD-RW is not be finalized correctly. Use finalized discs.  
• The CD pickup lens is dirty (see page 13).  
“ NO DISCor “NO SONGappears on the  
display.  
• MP3/WMA files are not recorded on the disc, USB mass storage  
class device, or SD card.  
ID3 Tag on an MP3 file cannot be shown.  
• There are two types of ID3 Tag—Version 1 and Version 2. This  
System can only show ID3 Tag Version 1.  
Groups and tracks are not played back as  
you expect.  
• Playing order is determined when the groups and tracks are  
recorded. It depends on the writing application.  
The disc/USB mass storage class device/SD • The disc is scratched or dirty.  
card sound is discontinuous.  
• MP3/WMA files have not been properly recorded onto the USB  
mass storage class device or SD card.  
Sound from the USB mass storage class  
device/SD card is interrupted.  
• Noise and static electricity may stop the sound. In this case,  
disconnect and connect the USB mass storage class device or  
remove and insert the SD card again after turning off the System.  
The disc/iPod door does not open or close. • The AC power cord is not plugged in.  
• The disc/iPod door is locked. Unlock it (see page 6).  
Daily Timer does not work.  
• The System was turned on when the on-time came. The timer  
stars working only when the System is turned off.  
• If the System does not work correctly, disconnect the AC power cord from the wall outlet, wait for a while, then  
connect the cord again.  
• JVC bears no responsibility for any loss of data in USB mass storage class device, SD card, or iPod while using this  
System.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Specifications  
To get the best performance of the System, keep your  
discs and the mechanism clean.  
Amplifier section  
Output Power:  
Audio Input:  
4 W (2 W + 2 W) at 16 Ω (10% THD)  
AUDIO IN: Stereo mini (ø 3.5 mm)  
250 mV/47 kΩ  
Handling discs  
• Remove the disc from its case by holding it at the edge  
while pressing the center hole lightly.  
• Do not touch the shiny surface of the disc, or bend the  
disc.  
Digital input:  
USB terminal  
Tuner  
FM tuning range:  
87.5 MHz – 108.0 MHz  
• Put the disc back in its case after use.  
• Be careful not to scratch the surface of the disc when  
placing it back in its case.  
Disc player  
Dynamic range:  
80 dB  
• Avoid exposure to direct sunlight, temperature  
extremes, and moisture.  
Wow and flutter:  
Immeasurable  
USB  
To clean the disc  
• Wipe the disc with a soft cloth in a straight line from  
center to edge.  
USB specification:  
Compatible device:  
Compatible system:  
Output power:  
Compatible with USB 2.0 Full Speed  
Mass storage class  
FAT16, FAT32  
DC 5 V 500 mA  
Cleaning the System  
• Stains should be wiped off with a soft cloth. If the  
System is heavily stained, wipe it with a cloth soaked in  
water-diluted neutral detergent and wrung well, then  
wipe clean with a dry cloth.  
SD  
Compatible device:  
Compatible system:  
SD, SDHC  
FAT16, FAT32  
• Since the System may deteriorate in quality, become  
iPod  
damaged or get its paint peeled off, be careful about the Output power:  
DC 5 V 500 mA  
following:  
– DO NOT wipe it hard.  
General  
– DO NOT wipe it with thinner or benzine.  
– DO NOT apply any volatile substances such as  
insecticides to it.  
– DO NOT allow any rubber or plastic to remain in  
contact for a long time.  
Speaker type:  
Speaker unit:  
Speaker impedance:  
Power requirements:  
Power consumption:  
Bass-Reflex type  
8 cm (3-3/16˝) x 2  
16 Ω  
AC 120 V  
/ 60 Hz  
25 W (at operation)  
1.00 W or less (on standby)  
400 mm × 215 mm × 91 mm  
(15-3/4˝ × 8-1/2˝ × 3-5/8˝)  
(W × H × D)  
Cleaning the CD pickup lens  
Keep the CD pickup lens clean, or  
the sound may be degraded. Use  
a blower (available at a camera  
store, etc.) to blow dust off the  
lens.  
Dimensions (approx.):  
Mass (approx.):  
2.3 kg (5.1 lbs)  
Supplied accessories  
Check to make sure that you have all the following items.  
• Remote control (× 1)  
• Lithium coin battery CR2025 (× 1)  
The battery has been installed in the remote control  
when shipped from the factory.  
• Microsoft and Windows Media are either registered  
trademarks or trademarks of Microsoft Corporation  
in the United States and/or other countries.  
• “Made for iPodmeans that an electronic accessory  
has been designed to connect specifically to  
iPod, and has been certified by the developer to  
meet Apple performance standards. Apple is not  
responsible for the operation of this device or its  
compliance with safety and regulatory standards.  
• iPod, iPod classic, iPod nano, and iPod touch are  
trademarks of Apple Inc., registered in the U.S. and  
other countries.  
Design and specifications are subject to change without  
notice.  
• SDHC Logo is a trademark.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Types de disques/fichiers reproductibles  
Dans ce manuel...  
• Sauf mention contraire, les touches de la  
télécommande sont utilisées pour expliquer les  
opérations. Cependant, si le système possède des  
noms de touches identiques ou similaires, ces  
touches peuvent être utilisées pour les opérations.  
• Les mots “fichier” et “plage”, “groupe” et “dossier”  
sont utilisés de façon interchangeable.  
• Ce système peut reproduire...  
– CD Audio et CD-R/CD-RW au format CD Audio  
– Fichiers MP3/WMA sur un CD-R/CD-RW (format ISO  
9660), un périphérique USB à mémoire de grande  
capacité ou une carte SD/SDHC (vitesse de transfert  
maximum des données: 2 Mbps)  
• Ce système ne peut pas reproduire les disques à  
“écriture par paquets”.  
• Pour la lecture MP3/WMA...  
Précautions  
– Certains fichiers MP3/WMA ne peuvent pas  
être reproduits à cause de leurs conditions  
d’enregistrement.  
– Ce système peut uniquement reproduire les disques  
au format ISO 9660 Niveau 1 ou Niveau 2.  
– Ce système peut reconnaître un maximum de  
999 plages et de 99 groupes.  
– Ce système peut afficher les données des balises  
(version 1).  
• Pour la lecture USB/SD...  
– Vous ne pouvez pas reproduire des fichiers dont la  
taille fait plus de 2 Go.  
– Il se peut que ce système ne puisse pas reproduire  
certains périphériques USB à mémoire de grande  
capacité/cartes SD et elle ne prend pas en charge la  
gestion des droits numériques DRM (Digital Rights  
Management).  
Remarques sur le cordon d’alimentation  
• Quand vous vous absentez pendant une période  
prolongée, retirer la fiche de la prise murale.  
• Pour débrancher le système de la prise murale,  
tirez toujours sur la fiche et non pas sur le cordon  
d’alimentation secteur.  
• Ne manipulez pas le cordon d’alimentation avec les  
mains mouillées.  
• Débranchez le cordon d’alimentation avant de nettoyer  
ou de déplacer le système.  
• Ne modifiez pas, ne tordez ni ne tirez sur le cordon  
d’alimentation, et ne mettez aucun objet lourd  
dessus, car cela pourrait entraîner un incendie, une  
électrocution ou d’autres accidents.  
Évitez l’humidité, l’eau, la poussière et les hautes  
températures  
• Ne placez pas le système dans un endroit humide ou  
poussiéreux.  
Remarques sur l’utilisation de périphériques  
USB à mémoire de grande capacité  
• Connectez un périphérique USB à mémoire de grande  
capacité quand le système est hors tension pour éviter  
tout mauvais fonctionnement.  
• N’utilisez pas de nœud de raccordement USB.  
• Il est recommandé d’utiliser un périphérique USB à  
mémoire de grande capacité d’une capacité de moins  
de 4 Gigaoctets.  
• Mettez hors service la fonction de sécurité du  
périphérique USB à mémoire de grande capacité avant  
de la connecter.  
Si de l’eau pénétrait à l’intérieur du système, mettez-le  
hors tension et débranchez la fiche de la prise murale,  
puis consultez votre revendeur. Utiliser le système dans  
cet état peut entraîner un incendie ou une électrocution.  
• N’exposez pas le système directement aux rayons du  
soleil ni ne la placez près d’un dispositif de chauffage.  
Remarques sur l’installation  
• Choisissez un endroit plat, sec, et ni trop chaud, ni trop  
froid—entre 5˚C et 35˚C (41˚F et 95˚F).  
• N’installez pas le système dans un endroit sujet aux  
vibrations.  
• Ne placez pas d’objet lourd sur le système.  
• Lors de l’utilisation d’un câble USB pour la connexion du  
périphérique, utilisez un câble USB 2.0 d’une longueur  
de moins d’un mètre.  
Pour éviter tout mauvais fonctionnement ou  
dommage au système  
• N’insérez aucun objet métallique, tel qu’un câble, une  
épingle à cheveux, une pièce de monnaie, etc. dans le  
système.  
• Le périphériques USB à mémoire de grande capacité est  
chargé par la prise  
quand “USB” est choisi comme  
source. (Certains périphériques USB à mémoire de  
grande capacité peuvent ne pas être chargés par la prise  
quand “USB” est choisi comme source.)  
• Vous ne pouvez pas connecter un ordinateur à la prise  
de ce système.  
• N’obstruez pas les évents d’aération.  
Remarques sur l’utilisation du système  
• Ne transportez pas le système la porte du disque/iPod  
ouverte.  
• Un choc électrostatique à la connexion d’un  
périphérique USB à mémoire de grande capacité peut  
causer une lecture anormale du périphérique. Dans  
ce cas, déconnectez le périphérique USB à mémoire  
de grande capacité puis réinitialiser cet appareil et le  
périphérique USB à mémoire de grande capacité.  
• Pendant la lecture d’un fichier d’un périphérique USB  
à mémoire de grande capacité, ne déconnectez pas  
le périphérique. Cela pourrait entraîner un mauvais  
fonctionnement du système et du périphérique.  
• Avant de déplacer le système assurez-vous de retirer le  
disque, l’iPod, le périphérique USB à mémoire de grande  
capacité et la carte SD, puis de débrancher le cordon  
d’alimentation.  
• Assurez-vous de fermer la porte du disque/iPod avant  
de mettre le système hors tension.  
Le lecteur ne contient pas d’éléments réparables par  
l’utilisateur. En cas d’anomalie, débranchez le cordon  
d’alimentation et consultez votre revendeur.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remarques sur l’utilisation d’un iPod  
Table des matières  
• Assurez-vous de réduire le volume sur le système au  
niveau minimum avant de connecter un iPod. Ajustez le  
volume après avoir démarré la lecture.  
• Vous ne pouvez envoyer aucunes données sur l’iPod à  
partir de ce système.  
• Ne transportez pas le système avec iPod connecté. Cela  
pourrait endommager le dock ou causer la chute de  
l’iPod.  
Introduction....................................................... 2  
Précautions.................................................................................... 2  
Types de disques/fichiers reproductibles .......................... 2  
Remarques sur l’utilisation de périphériques USB à  
mémoire de grande capacité.................................................. 2  
Remarques sur l’utilisation d’un iPod .................................. 3  
Remarques sur l’utilisation d’une carte SD ........................ 3  
• Ne touchez pas et ne heurtez pas les broches de la prise  
de l’iPod, ni celles du connecteur dans le dock de iPod.  
Cela pourrait endommager les broches du connecteur.  
• L’iPod est chargé par le dock quand le système est sous  
tension.  
Pour commencer ............................................... 4  
Préparation de l’antenne FM .................................................. 4  
Connexion du cordon d’alimentation ................................. 4  
Préparation de la télécommande.......................................... 4  
Opérations de base ........................................... 5  
Utilisation du casque ................................................................. 5  
• Les informations apparaissant sur l’affichage diffèrent  
en fonction du type d’iPod.  
• Si la lecture sur iPod ne se fait pas correctement, mettez  
à jour le logiciel de iPod à la dernière version. Pour en  
savoir plus sur la mise à jour de iPod, consultez le site  
Web de Apple <http://www.apple.com>.  
Fonctionnement commun ................................ 6  
Réglage de l’horloge.................................................................. 6  
Pour fermer la porte du disque/iPod ................................... 6  
Minuterie d’arrêt.......................................................................... 6  
Minuterie quotidienne .............................................................. 7  
Ajustements du son ................................................................... 7  
Changement des informations sur l’affichage ................. 7  
Modèles d’iPod compatibles  
• iPod nano (2ème, 3ème, 4ème, 5ème et 6ème  
génération)  
• iPod nano  
• iPod touch (2ème, 3ème et 4ème génération)  
• iPod touch  
• iPod (4ème génération)  
• iPod classic  
Opérations de lecture ....................................... 8  
iPod .................................................................................................. 8  
Disque/USB/SD ............................................................................ 8  
Radio FM.......................................................................................10  
Appareil extérieur .....................................................................11  
• iPod photo (4ème génération)  
• iPod video (5ème génération)  
• iPod mini (2ème génération)  
• iPod mini  
Références........................................................12  
Guide de dépannage ...............................................................12  
Entretien.......................................................................................13  
Spécifications..............................................................................13  
Remarques sur l’utilisation d’une carte SD  
• N’insérez AUCUN objet autre qu’une carte SD dans la  
ATTENTION: Aération correcte  
Pour prévenir tout risque de décharge électrique  
ou d’incendie et éviter toute détérioration, installez  
l’appareil de la manière suivante:  
fente d’insertion.  
• N’utilisez PAS une carte SD endommagée ou déformée.  
• Assurez-vous que la lecture de la carte SD est arrêtée  
avant de retirer la carte SD. Sinon, les données risquent  
d’être endommagées.  
• N’insérez jamais la carte SD à l’envers. Sinon, vous ne  
pourrez plus la retirer.  
• Lors de la lecture d’une carte miniSD™/microSD™,  
assurez-vous de fixer l’adaptateur miniSD™/microSD™  
avant d’insérer la carte.  
1. Avant: Bien dégagé de tout objet.  
2. Flancs/Dessus/Arrière: Aucun obstacle ne doit être  
placé dans les zones indiquées par les dimensions  
dans l’illustration.  
3. Dessous: Posez l’appareil sur une surface plane et  
horizontale. Veillez à ce que sa ventilation correcte  
puisse se faire en le plaçant sur un support d’au  
moins dix centimètres de hauteur.  
• Vous pouvez utiliser une carte SD d’une capacité  
maximale de 32 Go.  
Face  
Côté  
15 cm  
15 cm  
(5-15/16˝)  
(5-15/16˝)  
15 cm  
15 cm  
(5-15/16˝)  
(5-15/16˝)  
15 cm  
(5-15/16˝)  
10 cm  
10 cm  
(3-15/16˝) (3-15/16˝)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pour commencer  
Préparation de l’antenne FM  
Préparation de la télécommande  
Étendez l’antenne FM de façon à obtenir la meilleure  
Quand vous utilisez la télécommande pour la première  
réception possible.  
fois, retirez la feuille isolante.  
Antenne FM  
Pour remplacer la pile dans de la télécommande  
• Assurez-vous que le conducteur d’antenne ne touche  
aucunes autres prises, cordons de connexion ou cordon  
d’alimentation. De plus, gardez l’antenne à l’écart  
des parties métalliques du système, des cordons de  
connexion et du cordon d’alimentation secteur. Sinon,  
la réception pourrait en être affectée.  
Attention  
Danger d’explosion si la pile est remplacée de façon  
incorrecte. Remplacez-la uniquement avec le même type  
de pile ou un type équivalent.  
Connexion du cordon d’alimentation  
Assurez-vous de brancher le cordon d’alimentation à  
une prise murale uniquement après que toutes les autres  
connexions ont été faites.  
• Rangez la pile dans un endroit hors d’atteinte des  
enfants. Si un enfant avale accidentellement la pile,  
consultez immédiatement un médecin.  
• Pour éviter que la pile ne chauffe, ne se fissure ou cause  
un incendie:  
– Ne rechargez pas, ne court-circuitez pas, ne chauffer  
pas la pile ni ne la jeter dans un feu.  
– Ne laissez pas la pile avec d’autres objets métalliques.  
– Enveloppez la pile de ruban isolant avant de la mettre  
au rebut ou de la ranger.  
À une prise murale  
– Ne piquez pas la pile avec des ciseaux ou d’autres  
objets similaires.  
• Mettez de la pile au rebut correctement en respectant la  
régulation fédérale, régionale ou locale.  
• Les piles (blocs-piles ou pile installée) ne doivent pas  
être exposées à une source de chaleur excessive telle  
que la lumière du soleil, un feu ou quelque chose de  
similaire.  
Réglez l’horloge avant d’utiliser ce système (voir  
page 6).  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Opérations de base  
Témoin STANDBY  
Capteur de télécommande  
Mettez le système sous  
tension.  
1
Choisissez une source.  
Ajustez le volume.  
2
3
• Pour mettre l’appareil hors tension,  
appuyez sur  
.
1 2 3  
NE METTEZ PAS le système hors  
tension quand son niveau de volume  
est réglé extrêmement haut; sinon  
la déflagration soudaine du son  
pourrait endommager votre ouïe, les  
enceintes et le casque d’écoute lors de  
la mise sous tension du système ou le  
démarrage de la lecture.  
1
2
• Quand le système est mise hors  
tension avec le volume réglé sur plus  
de “17”, le niveau de volume est réglé  
automatiquement sur “16” la prochaine  
fois que vous mettez le système sous  
tension.  
3
Utilisation du casque  
Connectez un casque d’écoute (non fourni) à la prise  
en  
utilisant un cordon à fiche stéréo mini (non fourni).  
Assurez-vous de réduire le volume avant de connecter  
un casque ou de vous le mettre sur les oreilles.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fonctionnement commun  
Réglage de l’horloge  
Minuterie d’arrêt  
Vous pouvez régler l’horloge uniquement quand le  
Vous pouvez régler la minuterie d’arrêt uniquement  
système est hors tension (en attente).  
quand le système est sous tension.  
Affichez le réglage de l’horloge.  
Affichez le réglage de la minuterie  
d’arrêt.  
1
1
(Maintenez  
pressée)  
(Maintenez  
pressée)  
Ajustez les heures et minutes.  
2
Spécifiez l’heure de mise hors tension.  
2
(Annulé)  
• L’horloge peut avancer ou retarder d’une ou deux  
minutes par mois. Vous aurez peut-être besoin de  
réajuster l’horloge périodiquement.  
• Pour vérifier la durée restante jusqu’à la mise hors  
tension, maintenez pressée CLOCK/SLEEP.  
• Pour vérifier l’heure actuelle pendant que le système est  
sous tension, appuyez sur CLOCK/SLEEP.  
• En cas de panne de courant, les réglages de l’horloge  
sont perdus. Vous devez régler l’horloge à nouveau.  
Pour fermer la porte du disque/iPod  
Vous pouvez verrouiller la porte du disque/iPod pour  
éviter qu’elle s’ouvre accidentellement.  
Quand la porte du disque/iPod est fermée...  
Sur l’appareil:  
(Tenez en même temps)  
(Défile sur l’affichage)  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Minuterie quotidienne  
Ajustements du son  
En utilisant la minuterie quotidienne, vous pouvez vous  
réveiller au son de votre musique préférée.  
• Préparez en avance la source de lecture.  
Sourdine  
Vous pouvez baisser le volume instantanément.  
Affichez le réglage de la minuterie quotidienne.  
1
• Pour rétablir le volume, appuyez de nouveau sur la  
touche ou ajuster le volume.  
(Maintenez  
pressée)  
Les options de réglage de la minuterie sont affichées.  
Hyper Bass Sound (HBS)  
Vous pouvez renforcer les sons graves.  
Réglez le contenu de la minuterie.  
Vous pouvez régler les éléments suivants:  
2
ON TIME Heures et minutes pour l’heure de  
début de la minuterie  
Annulé  
(Pas d’indication)  
OFFTIME Heures et minutes pour l’heure de fin  
de la minuterie  
SOURCE  
Source de lecture  
• “A-IN” n’est pas disponible.  
Mode sonore  
Vous pouvez choisir le mode sonore qui convient à votre  
musique préférée.  
1 Choisissez une option de réglage.  
2 Réglez l’option choisie.  
Annulé (Pas d’indication)  
3 Validez le réglage.  
• Pour régler les heures/minutes: Appuyez sur  
¢ ou 4, puis sur TIMER.  
Pour régler la source: Appuyez sur CD 6, iPod 6,  
USB 6, SD 6 ou FM/AUDIO IN puis sur TIMER.  
Changement des informations sur l’affichage  
Vous pouvez afficher les informations des balises ID3/WMA