JVC Home Theater System SP THS11BC SP THS11BS User Manual

DVD DIGITAL THEATER SYSTEM

TH-S11B

Consists of XV-THS11B, SP-THS11BW,

SP-THS11BF, SP-THS11BC and SP-THS11BS

For Customer Use:

INSTRUCTIONS

Enter below the Model No. and Serial

No. which are located either on the rear,

bottom or side of the cabinet. Retain this

information for future reference.

Model No.

Serial No.

GVT0155-018A

[J]

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover or cabinet. There are

no user serviceable parts inside the unit; leave all servicing

to qualified service personnel.

3. CAUTION:

Visible and/or invisible class II laser radiation when open.

Do not stare into beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL,

PLACED INSIDE THE UNIT.

[European Union only]

IMPORTANT POUR LES PRODUITS LASER

1. PRODUIT LASER CLASSE 1

[Union européenne seulement]

2. ATTENTION: N’ouvrez pas le couvercle supérieur ni le

coffret de l’appareil. Il n’y a aucune pièce réparable par

l’utilisateur à l’intérieur de l’appareil; confiez toute

réparation à un personnel qualifié.

CAUTION

Excessive sound pressure from earphones or headphones can

cause hearing loss.

3. ATTENTION:

Radiation laser de classe II visibles et/ou invisible si

l’appareil est ouvert. Ne regardez pas le rayon.

4. REPRODUCTION DE L’ÉTIQUETTE: ÉT QUETTE DE

PRÉCAUTION PLACÉE L’INTERIEUR DE

L’APPAREIL.

ATTENTION

Une pression acoustique excessive des écouteurs ou du casque

d’écoute peut entraîner une perte auditive.

For U.S.A.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of

the following measures:

Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for

help.

G-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of contents

Introduction .....................................2

Notes on handling .................................................................2

Supplied accessories ............................................................2

Playback ........................................13

Basic playback ....................................................................13

One touch replay .................................................................15

Fast-forward/fast-reverse search ........................................15

Skip to the beginning of a desired selection .......................15

Locating a desired title/group using number buttons .........16

Selecting the desired title/playlist from the control display ..... 16

About discs .....................................3

Playable disc types ...............................................................3

Index of parts and controls ............4

Advanced operations ....................17

Using the surround mode ...................................................17

Using the on-screen bar .....................................................18

Playing from a specified position on a disc .........................20

Using the file control display ..............................................21

Resume playback ................................................................22

Selecting a view angle .........................................................22

Selecting the subtitle ..........................................................23

Selecting the audio .............................................................23

Special picture playback .....................................................24

Program playback ...............................................................25

Random playback ...............................................................25

Repeat playback ..................................................................26

Tray lock .............................................................................27

Balance setting ...................................................................27

Connections ....................................6

Connecting the FM and AM antennas ....................................6

Connecting the satellite (front, center, surround) speakers and

the subwoofer ......................................................................... 7

Speaker layout ......................................................................8

Connecting a TV ....................................................................8

Connecting an external component .......................................8

Connecting the power cord ...................................................8

Operating the TV .............................9

Basic operations ...........................10

Turning the system on/off ...................................................10

Selecting the source to play ................................................11

Adjusting the volume [VOLUME] ........................................11

Listening with headphones (not supplied) ..........................11

Turning off the sound temporarily [MUTING] .....................11

Adjusting the brightness of the indications [DIMMER] .......11

Sleep Timer [SLEEP] ...........................................................12

Adjusting the output level of the front/center/surround

Setting DVD preferences ..............28

Using the setup menus .......................................................28

Menu description ................................................................28

Tuner operations ...........................31

Manual tuning .....................................................................31

Preset tuning ......................................................................32

Selecting the FM reception mode ........................................32

speakers and subwoofer .....................................................12

Adjusting the sound ............................................................12

Changing the scan mode ....................................................12

References ....................................33

Maintenance .......................................................................33

Troubleshooting ..................................................................33

Specifications .....................................................................34

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

7 Safety precautions

Avoid moisture, water and dust

Notes on handling

7 Important cautions

Installation of the system

• Select a place which is level, dry and neither too hot nor too cold;

between 5°C (41°F) and 35°C (95°F).

Do not place the system in moist or dusty places.

Avoid high temperatures

Do not expose the system to direct sunlight and do not place it near

a heating device.

When you are away

When away on travel or for other reasons for an extended period of

time, disconnect the power cord plug from the wall outlet.

• Leave sufficient distance between the system and the TV.

• Do not use the system in a place subject to vibration.

Power cord

Do not block the vents

Blocking the vents may damage the system.

• Do not handle the power cord with wet hands!

• A small amount of power is always consumed while the power

cord is connected to the wall outlet.

• When unplugging the power cord from the wall outlet, always

pull on the plug, not the power cord.

Care of the cabinet

When cleaning the system, use a soft cloth and follow the relevant

instructions on the use of chemically-coated cloths. Do not use

benzene, thinner or other organic solvents including disinfectants.

These may cause deformation or discoloring.

To prevent malfunctions of the system

• There are no user-serviceable parts inside. If anything goes

wrong, unplug the power cord and consult your dealer.

• Do not insert any metallic object into the system.

• Do not use any non-standard shape disc (like a heart, flower or

credit card, etc.) available on the market, because it may damage

the system.

If water gets inside the system

Turn the system off and disconnect the power cord plug from the

wall outlet, then call the store where you made your purchase.

Using the system in this condition may cause fire or electrical

shock.

• Do not use a disc with tape, stickers, or paste on it, because it

may damage the system.

Label sticker

Supplied accessories

Check to be sure you have all of the supplied accessories.

The number in parentheses is the quantity of the pieces supplied.

If anything is missing, contact your dealer immediately.

Sticker

Paste

• Remote control (1)

• Batteries (2)

• FM antenna (1)

Note about copyright laws

• AM loop antenna (1)

• Composite Video cord (1)

Check the copyright laws in your country before recording from the

discs. Recording of copyrighted material may infringe copyright

laws.

Note about copyguard system

The discs are protected by copyguard system. When you connect

the system to your VCR directly, the copyguard system activates

and the picture may not be played back correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

About discs

Notes on DVD-R, DVD-RW and DVD-RAM

• This system can also play finalized DVD-Rs or DVD-RWs

recorded in DVD VIDEO format and DVD-RWs or DVD-RAMs

recorded in DVD VR format.

• This system can also play DVD-Rs or DVD-RWs if MP3 and

JPEG files are recorded on them with UDF Bridge format.

This system does not support “multi-border” disc.

Playable disc types

This system has been designed to play back the following discs:

DVD VIDEO, Video CD (VCD), Super Video CD (SVCD), Audio

CD (CD), CD-R and CD-RW.

• This system accommodates the NTSC system, and also can play

discs recorded with PAL system.

• This system can also play finalized DVD-R/-RWs recorded in

DVD VIDEO format. However, some discs may not be played

because of their disc characteristics or recording conditions.

Notes on CD-R and CD-RW

• This system can also play CD-Rs or CD-RWs if MP3 and JPEG

files are recorded on them with ISO 9660 format.

• This system supports “multi-session” discs (up to 20 sessions).

• This system cannot play “packet write” discs.

Discs you can play:

DVD VIDEO

Audio CD

SVCD

Some discs may not be played back because of their disc

characteristics, recording conditions, or damage or stain on them.

For all playable files

• The system can only recognize and play files with one of the

following extensions, which can be in any combination of upper

and lower case;

VCD

MP3:

“.MP3”, “.mp3”

JPEG:

“.JPG”, “.JPEG”, “.jpg”, “.jpeg”

• The system recognizes up to 150 tracks (files) per group, 99

groups per disc, and the total number of the tracks (files) that the

system can play is 4 000.

• Some files may not be played back normally because of their disc

characteristics or recording conditions.

• The following discs cannot be played back:

CD-I (CD-I Ready), Photo CD, SACD, etc.

Playing back these discs will generate noise and damage the

speakers.

• The Non-DVD side of a “DualDisc” does not comply with the

“Compact Disc Digital Audio” standard. Therefore, the use of

Non-DVD side of a DualDisc on this product may not be

recommended.

• On some DVD VIDEOs, VCDs or SVCDs, their actual

operation may be different from what is explained in this

manual. This is due to the disc programming and disc

structure, not a malfunction of this system.

• MP3/JPEG discs require a longer readout time. (It differs due to

the complexity of the directory/file configuration.)

• If different kinds of the file are mixed on a disc, set the FILE

TYPE setting in the PICTURE menu to the appropriate setting

for the data to be read (“AUDIO” or “STILL PICTURE”). (See

page 29.)

Notes on MP3 files

• Tag information (album name, artist name, and track name) can

be shown on the TV. (See page 21.)

• The system can play back the MP3 files recorded at 32 kbps to

320 kbps as a bit rate, and at 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,

44.1 kHz and 48 kHz as a sampling frequency.

DVD Logo is a trademark of DVD Format/Logo Licensing

Corporation.

• We recommend to record each piece of material (song) at a

sample rate of 44.1 kHz and at a data transfer rate of 128 kbps.

Region code of DVD VIDEO

DVD VIDEO players and DVD VIDEO discs have their own

Region Code numbers. This system can play back DVD VIDEO

discs whose Region Code numbers include “1.”

• Example of playable DVD:

Notes on JPEG files

• We recommend to record a file at 640 x 480 resolution. (If a file

has been recorded at a resolution of more than 640 x 480, it will

take a longer time to be displayed.)

1 2

3 4

ALL

• This system can only play baseline JPEG files.

1 2

If a DVD with an improper Region Code number is loaded,

“REGION CODE ERROR!” appears on the TV screen and

playback cannot start.

This product incorporates copyright protection technology that is

protected by U.S. patents and other intellectual property rights. Use

of this copyright protection technology must be authorized by

Macrovision, and is intended for home and other limited viewing

uses only unless otherwise authorized by Macrovision. Reverse

engineering or disassembly is prohibited.

Download from Www.Somanuals.com. All Manuals Search And Download.

Index of parts and controls

The numbers in the figures indicate the pages where the details of the parts are described.

Front panel (center unit)

Display window

FM AM

P LPCM SURR

WMAMP3 AAC RESUME

MHz

kHz

PROGRESSIVE B.S.P. CHAP. TRK PG PL BONUS ST MONO RDS TA NEWS INFO PRG RND

VOLUME

STANDBY

TUNING

SOURCE

PHONES

Disc tray (inside): 13

Remote sensor: 5

Rear panel (center unit)

Download from Www.Somanuals.com. All Manuals Search And Download.

Index of parts and controls

Remote control

Putting batteries in the remote control

STANDBY/ON

REPEAT

A-B RPT

SLEEP

Number

R6 (SUM-3)/AA (15F) type dry-cell batteries (supplied)

TV/VIDEO

buttons:15

If the range or effectiveness of the remote control decreases,

replace both batteries.

DIMMER

SURROUND

MENU/PL

CAUTION

TOP MENU/PG

16, 20,

12, 16,

SET UP

SETTING

16, 20, 28

• Battery shall not be exposed to excessive heat such as sunshine and

fire.

ENTER

ON SCREEN

FL DISPLAY

DVD/CD

Operating the system from the remote

control

Aim the remote control directly to the front panel of the center unit.

• If you operate it from a diagonal position, the operating range

(approx. 5 m (16 ft)) may be shorter.

MEMORY FM MODE RETURN

15, 20

13, 32

15, 24

23, 24

22, 23

11, 13

13, 32

15, 31

11, 31

TUNING

SLOW

ANGLE

ZOOM

FM/AM

TITLE/

AUX

AUDIO SUBTITLE

• Do not block the remote sensor.

GROUP PLAY MODE CANCEL MUTING

BASS/

SCAN MODE TREBLE

TV CHANNEL

12, 24

VFP

9, 11

9, 12

SHIFT SPK-LEVEL

9, 11, 12,

22, 24, 26,

27, 28

LEVEL AUDIO VOL

TV VOL

DVD THEATER SYSTEM

REMOTE CONTROL RM-STHS33J

Download from Www.Somanuals.com. All Manuals Search And Download.

Do not connect the power cord until all other connections have been made.

Connections

If reception is poor

Connecting the FM and

AM antennas

Center unit

AM loop antenna

7 AM loop antenna

Setting up supplied AM loop antenna

Outdoor single vinyl-covered wire

antenna (not supplied)

If the antenna cord is covered with the insulation

coat, twist and pull the insulation coat off and

remove.

7 FM antenna

FM antenna (supplied)

Center unit

Connecting AM loop antenna

Extend the supplied FM antenna

horizontally.

If reception is poor

Center unit

Outdoor FM antenna

(not supplied)

Standard type (75 C

coaxial) connector

Outdoor FM antenna cord

(not supplied)

Antenna cord

NOTE

• We recommend that you use coaxial cable for the FM antenna as it is

well-shielded against interference.

• Turn the loop antenna until you have the best reception during

AM broadcast program reception.

NOTE

• Make sure the antenna conductors do not touch any other terminals,

connecting cords and power cords. This could cause poor reception.

Download from Www.Somanuals.com. All Manuals Search And Download.

Do not connect the power cord until all other connections have been made.

Connections

Connecting the satellite (front, center, surround)

speakers and the subwoofer

Front speakers

Center speaker

Speaker cord

• Connect the black cords to the black (-) terminals.

• Connect the white cords to the red (+) terminals.

Before connecting

the speaker cords;

Twist and pull the

insulation coat off

and remove.

Subwoofer

Surround speakers

• When installing the satellite speakers on the wall;

CAUTION

•

Be sure to have them installed on the wall by a qualified personnel.

DO NOT install the satellite speakers on the wall by yourself to

avoid unexpected damage from their falling off the wall due to

incorrect installation or weakness in wall structure.

• When you connect speakers other than the supplied ones, use

speakers of the same speaker impedance (SPEAKER IMPEDANCE)

indicated on the rear of the center unit.

• DO NOT connect more than one speaker to one speaker terminal.

•

Care must be taken in selecting a location for speaker installation

on a wall. Injury to personnel or damage to equipment may result

if the speakers installed interfere with daily activities.

Download from Www.Somanuals.com. All Manuals Search And Download.

Do not connect the power cord until all other connections have been made.

Connections

7 To connect a TV equipped with the S-VIDEO and/or

Speaker layout

the composite video input jacks

S-VIDEO cord

(not supplied)

Center unit

Center speaker

Front left

speaker

Front right

speaker

Subwoofer

Composite video cord

(supplied)

NOTE

• Select the appropriate scan mode according to your TV. (See page

12.)

Surround left

speaker

Surround right

speaker

Connecting an external

component

NOTE

You can enjoy the sound of an analog component.

• Place the satellite speakers on a flat and level surface.

• The front and center speakers are magnetically shielded to avoid color

distortions on TVs. However, if not installed properly, they may

cause color distortions. So, pay attention to the following when

installing the speakers.

Center unit

To audio output

– When placing the speakers near a TV set, turn off the TV’s main

power switch or unplug it before installing the speakers. Then wait

at least 30 minutes before turning on the TV’s main power switch

again.

Some TVs may still be affected even though you have followed the

above. If this happens, move the speakers away from the TV.

• The surround speakers and the subwoofer are not magnetically

shielded.

If it is located nearby the TV or monitor, it will probably cause

color distortion on the screen. To avoid this, do not place the

speaker nearby the TV or monitor.

• Be sure to place the subwoofer to the TV’s right side. If you place the

subwoofer to the TV’s left side, keep sufficient distance between

them to prevent the TV screen from appearing mottled.

RCA pin plug cord

(not supplied)

VCR

Cassette recorder

NOTE

• If you connect a sound-enhancing device such as a graphic equalizer

between the source components and this system, the sound output

through this system may be distorted.

• When playing a video component such as a VCR;

•

To listen to the sound, select “AUX” as the source to play. (See

page 11.)

To see the picture, connect the video output jack of the component

to the video input jack of the TV directly, and select the correct

input mode on the TV.

•

Connecting a TV

• Distortion of picture may occur when connecting the TV via a

VCR, or to a TV with a built-in VCR.

• You need to set “MONITOR TYPE” in the PICTURE menu

correctly according to the aspect ratio of your TV. (See page 29.)

Connecting the power

cord

Make sure that all other connections have been completed.

Center unit

7 To connect a TV equipped with the component video

input jacks

Center unit

Power cord

Plug into AC outlets.

CAUTION

To component

video input

• Disconnect the power cord before cleaning or moving the system.

• Do not pull on the power cord to unplug the cord. When unplugging

the cord, always grasp and pull the plug so as not to damage the cord.

Component video cord (not supplied)

NOTE

• If your TV supports progressive video input, you can enjoy a high

quality picture by setting the progressive scan mode to active. (See

page 12.)

• If the component video input jacks of your TV are of the BNC type,

use a plug adapter (not supplied) to convert the pin plugs to BNC

plugs.

• Preset settings, such as preset stations and surround mode adjustment,

may be erased in a few days in the following cases;

•

If you unplug the power cord of the center unit.

If a power failure occurs.

•

• The video signals can be output only when you select “DVD” as the

source to play. (See page 11.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating the TV

You can use the remote control to operate not only this unit but also JVC’s TV.

• Refer also to the manuals supplied for the TV.

• To operate the TV, aim the remote control directly at the remote sensor on the TV.

7 To operate a JVC’s TV

You can perform the following operations on the TV.

Turn on or off the TV.

Adjust the volume.

TV VOL +/– with SHIFT

pressed and held:

STANDBY/ON

REPEAT

A-B RPT

SLEEP

Set the input mode

(either TV or VIDEO).

TV/VIDEO:

TV/VIDEO

Change the channels.

CHANNEL +/– with SHIFT

pressed and held:

DIMMER

SURROUND

MENU/PL

TOP MENU/PG

SET UP

SETTING

ENTER

FL DISPLAY

DVD/CD

ON SCREEN

MEMORY FM MODE RETURN

TUNING

SLOW

ANGLE

ZOOM

FM/AM

TITLE/

AUX

AUDIO SUBTITLE

GROUP PLAY MODE CANCEL MUTING

BASS/

SCAN MODE TREBLE

TV CHANNEL

VFP

SHIFT SPK-LEVEL

LEVEL AUDIO VOL

TV VOL

DVD THEATER SYSTEM

REMOTE CONTROL RM-STHS33J

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations

The buttons on the remote control are used to explain most of the

operations in this manual. You can use the buttons on the center

unit same as on the remote control for operations unless

otherwise noted.

Turning the system on/off

On the remote control:

Press STANDBY/ON

The buttons described below are used on

pages 10 to 12.

On the center unit:

Press

When DVD is selected as the source (see page 11), the following

messages will appear on the TV screen.

STANDBY/ON

REPEAT

A-B RPT

SLEEP

TV/VIDEO

DIMMER

SURROUND

MENU/PL

TOP MENU/PG

SET UP

SETTING

• “OPEN”/“CLOSE”:

ENTER

Appears when opening or closing the disc tray.

• “NOW READING”:

Appears when the system is reading the disc information.

• “REGION CODE ERROR!”:

FL DISPLAY

DVD/CD

ON SCREEN

MEMORY FM MODE RETURN

Appears when the Region Code of the DVD VIDEO does not

match the code the system supports. The disc cannot be

played back.

• “NO DISC”:

Appears when no disc is loaded.

TUNING

SLOW

ANGLE

ZOOM

FM/AM

TITLE/

AUX

AUDIO SUBTITLE

GROUP PLAY MODE CANCEL MUTING

• “CANNOT PLAY THIS DISC”:

Appears when unplayable disc is loaded.

BASS/

TV CHANNEL

SCAN MODE TREBLE

VFP

SHIFT SPK-LEVEL

LEVEL AUDIO VOL

TV VOL

DVD THEATER SYSTEM

REMOTE CONTROL RM-STHS33J

NOTE

• The STANDBY lamp goes off when the power is turned on, and the

lamp lights when the power is turned off.

• A small amount of the power is consumed even when the power is

turned off. This is called standby mode and the STANDBY lamp

lights in this mode. Unplug the power cord from the AC outlet to turn

the power off completely.

• You can also turn on the system by pressing the following buttons;

•

0 on the center unit

One of the source selecting buttons on the remote control

3 on the center unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 10 for button locations.

Basic operations

Selecting the source to

play

Listening with headphones

(not supplied)

On the remote control:

CAUTION

Be sure to turn down the volume;

Press one of the source selecting buttons

• Before connecting or putting on headphones as high volume may

damage both the headphones and your hearing.

• Before disconnecting headphones as high volume may be suddenly

output from the speakers.

(DVD/CD3, FM/AM or AUX).

DVD/CD3: To play back a disc (DVD VIDEO, VCD etc.). (See

page 13.)

FM/AM:

AUX:

To tune in an FM or AM station. (See page 31.)

Each time you press the button, the band alternates

between FM and AM.

To select the external component connected to the

center unit. (See page 8.)

While connecting a pair of headphones to the PHONES jack on the

center unit, the system automatically cancels the surround mode

(see page 17) currently selected, deactivates the speakers, and

activates the headphone mode. “H.PHONE” appears on the display

window.

On the center unit:

Headphone mode

When using the headphones, the following signals are output

regardless of your speaker setting;

• For 2 channel sources, the front left and right channel signals are

output from the headphones.

Press SOURCE repeatedly until the source

name you want appears on the display

window.

• Multi-channel signals are down-mixed and output from the

headphones.

NOTE

• When a source except DVD is selected, this system does not output

video signals.

• It may take time to change the source.

Turning off the sound

temporarily [MUTING]

Adjusting the volume

[VOLUME]

Press MUTING.

To restore the sound

Perform one on the following:

• Press MUTING again.

• Press AUDIO VOL +/– (or turn VOLUME on the center unit).

CAUTION

• Always set the volume to minimum level before starting any source.

If the volume is set at its high level, the sudden blast of sound could

permanently damage your hearing and/or blow out the speakers.

On the remote control:

Adjusting the brightness

of the indications

[DIMMER]

Press DIMMER, with SHIFT pressed.

Each time you repeat the procedure, the brightness level changes.

Press AUDIO VOL +/–.

On the center unit:

Turn VOLUME.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 10 for button locations.

Basic operations

Sleep Timer [SLEEP]

Adjusting the sound

The system turns off automatically when the specified period of

time has passed.

1 Press BASS/TREBLE to show “BASS”

or “TREBLE” on the display window.

Press SLEEP, with SHIFT pressed.

Each time you repeat the procedure, the shut-off time changes.

Each time you press the button, the indication alternates

2 ^bP^er^twe^es^ens^“L^BAE^SV^SE^{” a}L^nd+^“/^T–^Rt^Eo^BLa^Ed^”.just the level from

Example:

minutes

–8 to 8.

S L E E P

6 0

NOTE

• The adjustments take effect for all sources.

To check the remaining time

Press SLEEP, with SHIFT pressed once.

Changing the scan mode

The system can be accommodated to your TV’s scan mode.

• To use the system in progressive mode, it is required that the

center unit is connected to the TV using a component video cord

(not supplied) in advance. (See page 8.)

To change the remaining time

Press SLEEP repeatedly, with SHIFT pressed.

To cancel

Press SLEEP repeatedly, with SHIFT pressed until “SLEEP - -”

appears.

• Turning off the power also cancels the Sleep Timer.

7 While DVD is selected as the source and before playback

1 Press and hold SCAN MODE for

2 seconds, with SHIFT pressed.

Adjusting the output level

of the front/center/

surround speakers and

subwoofer

2 P^Thr^ee^cs^urs^renC^tu^ser^ttsⁱⁿo^gr^ap3^pea/^r2^{s on}t^to^hes^die^spl^le^ayc^wt ⁱtⁿh^doe^wd^.esired

mode.

• INTER,:

Select when your TV supports the

interlaced video input only.

• PROGRESS:

Select when your TV equipped with

component jacks supports the progressive

video input.

1 Press SPK-LEVEL to show the target

speaker indication on the display

window.

You can get better picture quality in the order —

3 P^Cor^me^ps^os^siteE^vN^ideT^oE^sR^Sw^-vh^ideil^oe^sth^Ce^oms^pe^onle^enc^tt^ve^idd^eomode

Each time you press the button, the indication of the speakers

changes as follows:

is displayed.

FRONTL Z FRONTR Z CENTER Z

SURR(surround) L Z SURR(surround) R Z

SUBWFR Z (back to the beginning)

When “PROGRESS” is selected, the PROGRESSIVE

indicator lights on the display window.

NOTE

• Although the picture may be distorted when you press ENTER, this

is not a malfunction of the system.

2 Press LEVEL +/– to adjust the output

level from –6 to 6.

NOTE

• There are some progressive TVs and High-Definition TVs that are

not fully compatible with this system, resulting in an unnatural

picture when playing back a DVD VIDEO in the progressive scan

mode. In such a case, change the scan mode to “INTER,”.

To check the compatibility of your TV, contact your local JVC

customer service center.

• You can also make adjustments by using the setup menu shown on the

TV screen. (See page 30.)

• The adjustments take effect for all sources.

• All JVC progressive TVs and High-Definition TVs are fully

compatible with this system.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playback

• The mark

for.

shows the types of discs the operation is available

Basic playback

1 Press 0 on the

The buttons described below are used on pages 13 to 16.

center unit.

• The system turns on and the

disc tray comes out.

2 Place a disc.

STANDBY/ON

REPEAT

A-B RPT

SLEEP

When placing an 8 cm

(3 inches) disc

Label side up

Number

buttons

TV/VIDEO

DIMMER

SURROUND

MENU/PL

TOP MENU/PG

SET UP

SETTING

ENTER

FL DISPLAY

DVD/CD

ON SCREEN

3 Press DVD/CD3 (play button).

For MP3

MEMORY FM MODE RETURN

The file control display (see page 21) appears on the TV screen.

TUNING

SLOW

For JPEG

ANGLE

ZOOM

FM/AM

TITLE/

AUX

AUDIO SUBTITLE

Each file (still pictures) is shown on the TV screen for about 3

seconds (slide-show). When stopping playback, the file control

display (see page 21) appears on the TV screen.

GROUP PLAY MODE CANCEL MUTING

BASS/

SCAN MODE TREBLE

TV CHANNEL

For DVD VR disc

VFP

Pressing TOP MENU/PG or MENU/PL shows the control display

on the TV screen (see page 16).

SHIFT SPK-LEVEL

LEVEL AUDIO VOL

TV VOL

7 To pause

DVD THEATER SYSTEM

REMOTE CONTROL RM-STHS33J

Press 8.

To return to playback, press 3 (play button).

7 To stop

Press 7.

7 On-screen guide icons

During DVD VIDEO playback, the following guide icons may

appear for a while on the TV screen;

•

: appears at the beginning of a scene containing multi-

subtitle languages.

: appears at the beginning of a scene containing multi-audio

languages.

: appears at the beginning of a scene containing multi-angle

views.

(Play),

(Pause),

(Fast forward/

fast-reverse),

(Slow-motion forward/

reverse): appears when you perform each operation.

•

: the disc cannot accept an operation you have tried to do.

NOTE

• (For JPEG) The system cannot accept operations even though you

press any buttons before the entire picture appears on the TV screen.

• If you do not want the on-screen guide icons to appear, see page 30.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 13 for button locations.

Playback

VCD/SVCD/CD

Example:

When a CD is played back

7 Playback information on the display window

DVD VIDEO

Example:

Signal and speaker

indicators

When a DVD VIDEO encoded with Dolby Digital 5.1ch is played

Track number

Elapsed playing time

(hour:minute:second)

Chapter number

LPCM

1 2

3: 3 1

SURR

1: 2 3: 3 1

2 4

Elapsed playing time (minute:second)

Signal and speaker indicators (See page 18.)

NOTE

Surround mode and digital signal format (See page 18.)

• When a VCD or SVCD with PBC function is played, the elapsed

playing time does not appear, but “PBC” appears.

Pressing FL DISPLAY

MP3 file

Signal and speaker

Title number

Chapter number

indicators

Track number

C 2 4

1 5

SURR

1 2 3

1 2 3 4

MP3

MP3 indicator

Elapsed playing time (minute:second)

(during playback only)

DVD VR disc

Example:

Pressing FL DISPLAY

Group number

During playback on the Original program*

Elapsed playing time

(hour:minute:second)

Title number

G 1 2

T 1

MP3

Track number

PG (Original program) indicator

JPEG file

Pressing FL DISPLAY

Title number

File number

Chapter number

1 2 3

J P E

Example:

During playback on the Playlist*

Pressing FL DISPLAY

Elapsed playing time

(hour:minute:second)

File number

Group number

Title number

G 1 2

F 1 2 3

3 0

0: 5 0: 3 0

NOTE

PL (Playlist) indicator

Pressing FL DISPLAY

• You can change the time information mode (except for MP3/JPEG).

(See page 19.)

• You can also check the playback information on the TV screen. (See

page 18.)

Playlist number

Chapter number

P L

1 C

* Pressing TOP MENU/PG or MENU/PL, you can change the

play mode. (See page 16.)

Continued on next page

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 13 for button locations.

Playback

7 Screen saver

Fast-forward/fast-reverse

7 During playback

On the remote control:

A TV screen may burn out if a static picture is displayed for a long

time. To prevent this, the system automatically dims the screen if a

static picture is displayed for over 5 minutes (the screen saver

function).

• Pressing any button will cancel the screen saver function.

• If you do not want to use the screen saver function, see page 29.

Press y or 1.

Each time you press the button, the

search speed changes (x2, x5, x10,

x20, x60).

One touch replay

You can move back the playback position by

10 seconds from the current position.

To return to normal speed playback

^{Press DVD/CD}3 (play button).

7 During playback

On the center unit:

On the remote control:

Press and hold x or 4.

Press

Continuously pressing x or 4 increases the fast-forward/

reverse search speed (x5=x20).

NOTE

• This function works in the same title.

• This feature may not work for some discs.

NOTE

• When a DVD VIDEO, DVD VR, VCD or SVCD is played back, no

sound comes out during fast-forward/reverse search.

• When a CD is played back, sound is intermittent and low during fast-

forward/reverse search.

• This feature may not work for some discs.

• For MP3, the search speed is not shown.

Skip to the beginning of a

desired selection

7 Using x / 4 buttons

7 For DVD VIDEO/DVD VR

(chapter): During playback

For VCD/SVCD (track):

During playback without PBC function

For CD/MP3/JPEG (track/file): During playback or while

stopped

Press x or 4 repeatedly.

NOTE

• When playing back an MP3/JPEG, you can make operations using the

file control display. (See page 21.)

• This feature may not work for some discs.

7 Using number buttons on the remote control

7 For DVD VIDEO/DVD VR (title, chapter):

While stopped, the title number is selected.

During playback, the chapter number is selected.

For VCD/SVCD (track):

During playback without PBC function

For CD/MP3/JPEG (track/file):

During playback or while stopped

Press number buttons (0-10, +10) to select

the desired number.

• For details on using the number buttons, see “How to use the

number buttons” below.

How to use the number buttons

To select 3:

To select 14:

To select 24:

To select 40:

Press 3.

Press +10, then 4.

Press +10 twice, then 4.

Press +10 three times, then 10.

Or press +10 four times, then 0.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 13 for button locations.

Playback

Locating a desired title/

group using number

buttons

Selecting the desired

title/playlist from the

control display

7 During playback or while stopped.

1 Press TOP MENU/PG or MENU/PL.

The control display is shown on the TV screen, and the system

starts playback of the first title/playlist.

1 Press TITLE/GROUP.

“_ _” or “_” is shown in the title/group

display area in the display window.

• The PLAY LIST is shown only when the playlist is on the

DVD VR disc.

Example:

During DVD VIDEO playback

TOP MENU/PG: shows the ORIGINAL PROGRAM.

Example:

_ _

1 2 3 4 5

2 While the display window shows “_ _”

or “_”, use number buttons (0-10, +10)

to enter the desired title or group

number.

The system starts playback from the first chapter/track/file of

the selected title/group.

• For details on using the number buttons, see “How to use the

number buttons”. (See page 15.)

*1: Title number

*2: Recording date

*3: Recording source (TV station, the input terminal of the

recording equipment etc.)

*4: Start time of recording

NOTE

• This feature may not work for some discs.

*5: Title of the original program/playlist (The title may not be

displayed depending on the recording equipment.)

*6: Current title

MENU/PL: shows the PLAY LIST.

Example:

*7: Playlist number

*8: Creating date of playlists

*9: Number of chapters

*10:Total playing time

*11:Current playlist

2 Press Y/5 to select the desired title/

playlist.

The system starts playback of the selected title/playlist.

To clear the control display

• Press ENTER.

About the play mode on a DVD VR disc

• Original program (ORIGINAL PROGRAM):

The system can play back the original picture in the recorded

order.

• Playlist (PLAY LIST):

The system can play back the playlist edited by the recording

equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced operations

• The mark

for.

shows the types of discs the operation is available

Using the surround mode

7 Auto Surround (AUTO SURR)

The buttons described below are used on pages 17 to 27.

This function automatically selects the appropriate surround mode

according to the input signals. For example, a multichannel source

is automatically reproduced in multichannel audio.

7 Dolby Surround

Dolby Pro Logic II*

STANDBY/ON

REPEAT

A-B RPT

SLEEP

Dolby Pro Logic II has a developed multichannel playback format

to decode all 2 channel sources — stereo source and Dolby

Surround encoded source — into a 5.1 channel.

Dolby Pro Logic II has two modes — Movie mode and Music

mode:

Number

buttons

TV/VIDEO

DIMMER

SURROUND

MENU/PL

• Pro Logic II Movie (MOVIE)

TOP MENU/PG

SET UP

SETTING

Suitable for reproduction of Dolby Surround encoded sources

ENTER

bearing the mark

Cursor

(3/2/Y/5)/

ENTER

• Pro Logic II Music (MUSIC)

Suitable for reproduction of any 2 channel stereo music sources.

FL DISPLAY

DVD/CD

ON SCREEN

Dolby Digital*

MEMORY FM MODE RETURN

Used to reproduce multichannel soundtracks of the software

TUNING

SLOW

encoded with Dolby Digital (

ANGLE

ZOOM

FM/AM

TITLE/

AUX

AUDIO SUBTITLE

7 DTS Digital Surround*

Used to reproduce multichannel soundtracks of the software

GROUP PLAY MODE CANCEL MUTING

encoded with DTS Digital Surround (

DTS Digital Surround (DTS) is another discrete multichannel

digital audio format available on CD and DVD software.

BASS/

TV CHANNEL

SCAN MODE TREBLE

VFP

SHIFT SPK-LEVEL

LEVEL AUDIO VOL

TV VOL

DVD THEATER SYSTEM

REMOTE CONTROL RM-STHS33J

Available Surround modes for each input signal

The B marks show available surround modes.

Surround

off

Auto

DTS Digital

Surround

Manufactured under license from

Dolby Laboratories. “Dolby”,

“Pro Logic”, and the double-D

symbol are trademarks of Dolby

Laboratories.

“DTS” and “DTS Digital

Surround” are registered

trademarks of DTS, Inc.

You can select these modes by

pressing SURROUND. (See

page 18.)

Mode

Dolby Surround

DSP

ALL ST*³

—

Surround

SURR

OFF

AUTO

SURR

Dolby

Digital

Signal

MOVIE*³MUSIC*³

DTS

—

Dolby Digital

(Multichannel)

—

Dolby Digital

(2 channel)

—

DTS Digital

Surround

(Multichannel)

—

DTS Digital

Surround

(2 channel)

—

Analog or Linear

PCM

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

7 All Channel Stereo

7 When playing back 2 channel source

All Channel Stereo (ALL ST) mode can reproduce a larger stereo

sound field using all the connected (and activated) speakers.

All Channel Stereo can be used while reproducing 2 channel stereo

source.

You can select either mode of Dolby Pro Logic II (MOVIE/

MUSIC) or the DSP (ALL ST) mode.

Press SURROUND repeatedly to select the

desired mode.

The surround mode is turned on and the current surround mode

appears on the display window.

Normal stereo sound

All Channel Stereo

Each time you press the button, the surround mode changes.

For details on each mode, see page 17.

To turn off the surround mode

Press SURROUND repeatedly until “SURR

OFF” appears on the display window.

7 Indicators on the display window

Storing adjustments — auto memory

Digital signal format indicators

When you turn the power off, the system memorizes the current

surround mode. The memorized mode is automatically recalled

when you turn the power on.

LPCM, SURR:

GD, SURR:

C, SURR:

Lights when Linear PCM signal comes in.

Lights when Dolby Digital signals come in.

Lights when DTS Digital (Surround) signals

come in.

No indication:

No digital signal indicator lights when analog

signals come in.

Using the on-screen bar

You can check disc information and you can use some functions

Dolby Surround mode indicators

GPLII: Lights when Dolby Pro Logic II mode is activated.

using the on-screen bar.

Source signal indicators, etc.

Light to indicate the incoming signals.

Showing the on-screen bar

7 Whenever a disc is loaded

a: Lights when the front left channel signal

comes in.

b: Lights when the center channel signal comes in.

c: Lights when the front right channel signal comes in.

d: Lights when the LFE channel signal comes in.

g: Lights when the surround left channel signal comes in.

i: Lights when the surround right channel signal comes in.

h: Lights when the monaural surround channel signal or 2

channel Dolby Surround signal comes in.

SW : Always lights.

Press ON SCREEN.

Each time you press the button, the on-

screen bar changes as follows on the TV

screen.

Example:

During DVD VIDEO playback

The channel with “ ” shows that the corresponding speakers are

reproducing the channels’ sound.

If the channels’ sound decoded into 5.1 channel is reproduced, only

“

” lights.

Selecting the surround mode

The system is set up to automatically select the optimal surround

mode for input signal from digital multichannel software.

When playing back 2 channel source, you can select the desired

surround mode manually.

OFF

(The on-screen bar disappears)

(back to the beginning)

• The currently selected item shows green.

NOTE

• This function also takes effect for the sources other than DVD.

• For FM/AM and AUX, you can select All Channel Stereo (ALL ST)

or SURR OFF.

7 When playing back digital multichannel software

(except during SURR OFF mode)

The appropriate multichannel surround mode (Dolby Digital, DTS

Digital Surround or Linear PCM) is automatically selected.

Continued on next page

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

F Shows playback status.

appears during playback.

: appears during fast forward/reverse.

7 Contents of the on-screen bar during playback

DVD VIDEO

: appears during playback in forward slow-motion/

reverse slow-motion.

appears when paused.

appears when stopped.

DVD VR

G Select this to change time information (E). See “Changing the

time information”.

H Select this for Repeat Playback. (See page 26.)

I Select this for time search function. (See page 21.)

J Select this for chapter search function. (See page 20.)

K Select this to change audio language, channel, or stream. (See

page 23.)

L Select this to change subtitle language. (See page 23.)

M Select this to change view angle. (See page 22.)

N Shows Playback Mode status.

VCD

SVCD

PROGRAM: appears during Program Playback. (See page 25.)

RANDOM: appears during Random Playback. (See page 25.)

Changing the time information

You can change the time information in the

on-screen bar on the TV screen and the

display window of the center unit.

7 During playback

1 Press ON SCREEN twice.

2 P^Thr^ee^os^n-s^scrC^eeuⁿr^bs^aro^ar^pp3^ears/2^{on th}t^eo^Th^Vi^sg^crh^eelⁿig^.ht

3 Press ENTER repeatedly to select the

desired information.

A Shows disc type.

B Shows audio information.

Example:

C Shows current title number.

When elapsed playing time of disc is selected.

D Shows current chapter number (for DVD VIDEO and DVD VR)

or track number (for other type of discs).

E Shows time information. See “Changing the time information”.

7 VCD/SVCD/CD

• TIME: Elapsed playing time of current track

• REM:

Remaining time of current track

• TOTAL: Elapsed time of disc

• T. REM: Remaining time of disc

7 DVD VIDEO/DVD VR

• TIME: Elapsed playing time of current chapter

• REM:

Remaining time of current chapter

• TOTAL: Elapsed time of Title/Program

• T. REM: Remaining time of Title/Program

4 Press ON SCREEN.

The on-screen bar disappears.

NOTE

• When playing back DVD VR, “TIME” and “REM” cannot be shown.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

2 Press number buttons (1-10, +10) to

• For details on using the number buttons, see “How to use the

number buttons”. (See page 15.)

Playing from a specified

position on a disc

select the number of the desired item.

You can start playing a title, chapter or track you specify. You can

also play a disc from specified time.

To return to the menu

Press RETURN repeatedly until the menu screen appears.

When “NEXT” or “PREVIOUS” is shown on the TV

screen:

Locating a desired scene from the DVD

• To go to the next page, press x.

• To return to the previous page, press 4.

DVD VIDEOs generally have their own menus which show

disc contents and you can display them on the TV screen.

You can locate a desired scene by using these menus.

NOTE

• If you want to play a PBC-compatible VCD/SVCD without using the

PBC function, perform any of the following:

7 Whenever a DVD VIDEO is loaded

•

Start playback by pressing number buttons while stopped.

Press x repeatedly until the desired track number is displayed,

then start playback by pressing 3 (play button).

The track number appears on the display window instead of

“PBC”.

1 Press TOP MENU/PG or MENU/PL.

•

The menu appears on the TV screen.

Example:

• To activate the PBC function when playing a PBC-compatible VCD/

SVCD without using the PBC function, perform any of the following:

•

Press TOP MENU/PG or MENU/PL.

•

Press 7 twice to stop playback, then press 3 (play button).

Locating a desired chapter using the on-

screen bar

Normally, a DVD VIDEO which contains more than one title

will have a “top” menu which lists the titles. Press

TOP MENU/PG to show the title menu.

Some DVD VIDEO may also have a different menu which is

shown by pressing MENU/PL.

7 During playback

See the instructions for each DVD VIDEO regarding its

2 ^pU^ars^tie^culC^aru^mr^es^nuo^.r 3/2/Y/5 to select a

1 Press ON SCREEN twice.

2 P^Thr^ee^os^n-s^scrC^eeuⁿr^bs^aro^ar^pp3^ears/2^{on th}t^eo^Th^Vi^sg^crh^eelⁿig^.ht

3 Press ENTER.

desired item.

3 Press ENTER.

• With some discs, you can also select items by entering the

corresponding number using number buttons.

Example:

During DVD VIDEO playback

Locating a desired scene using a VCD/

SVCD menu with PBC

A VCD or SVCD recorded with PBC has its own

menus such as a list of contained songs. You can

locate a specific scene by using these menus.

4 Press number buttons (0-9) to enter the

desired chapter number.

Example:

7 During playback with PBC function

To select 8:

To select 10:

To select 20:

To select 37:

Press 8.

1 Press RETURN repeatedly, with SHIFT

pressed until the menu appears on the

TV screen.

Press 1, then 0.

Press 2, then 0.

Press 3, then 7.

Example:

To correct a misentry

5 ^RP^er^pe^eas^ts^steE^{p 4}N^.TER.

6 Press ON SCREEN.

The on-screen bar disappears.

NOTE

• You can select up to the 99th chapter.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

Locating a desired position by specifying

the time

Using the file control

display

You can locate a desired position by specifying the time from the

beginning the disc (while stopped) or the current title/track (during

playback).

You can search and play desired groups and

tracks/files using the file control display on

the TV screen.

7 For DVD VIDEO/DVD VR:

During playback

Current group / total group Playback mode (PROGRAM,

number

For VCD/SVCD:

While stopped or during playback

RANDOM, REPEAT)

without PBC function

Track information

(for MP3 only)

Elapsed playing time of current

track (for MP3 only)

For CD:

During playback or while stopped

7 When specifying the elapsed playing time from the

beginning of the disc

Perform the following procedure while stopped.

7 When specifying the elapsed playing time from the

beginning of current title/track

Perform the following procedure during playback.

1 Press ON SCREEN twice.

2 P^Thr^ee^os^n-s^scrC^eeuⁿr^bs^aro^ar^pp3^ears/2^{on th}t^eo^Th^Vi^sg^crh^eelⁿig^.ht

3 Press ENTER.

Current group

Current track (file)

Current track (file) / total track

(file) number on current group

Total track (file)

number on disc

4 Use number buttons (0-9) to enter the

Playback status

time.

The file control display appears automatically during playback (for

MP3) or while stopped.

You can specify the elapsed playing time from the beginning

of the disc (while stopped) or from the beginning of the current

title/track (during playback).

Example:

To play back from a point 2 (hours): 34 (minutes): 08 (seconds)

elapsed

Press 2

Press 4

Press 3

Press 0

Press 8

To cancel a misentry

5 ^PP^rer^se^ss^Cs^ursE^orN²T^rE^epR^ea.^tedly.

6 Press ON SCREEN.

The on-screen bar disappears.

NOTE

• You can specify time in hours/minutes/seconds for DVD VIDEO/

DVD VR and in minutes/seconds for VCD/SVCD/CD.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

7 For MP3:

During playback or while stopped

For JPEG:

Selecting a view angle

1^WP^hir^lee^ss^tos^ppC^edursor 3/2/Y/5 to select the

7 During playback of a disc containing multi-view angles

When using the ANGLE button:

desired group/track/file.

1 Press ANGLE, with SHIFT pressed.

• For MP3, playback starts from the selected track.

Example:

2 ^•Pr^Fe^ors^Js^PED^G,V^prD^oc/^eC^edD^to3^pero^for^rmE^tN^heT^foE^lloR^w.^{ing operation.}

The first view angle is selected out of 3 view angles recorded.

• Track playback/slide-show starts from the selected track/

file.

• When you press ENTER for JPEG, only the selected file is

played back.

2 Press ANGLE repeatedly, with SHIFT

pressed or Cursor Y/5 to select the

desired view angle.

To skip the file during playback

Press x/4 or Cursor 5/Y.

NOTE

• You can also check playback information on the display window.

(See page 14.)

When using the on-screen bar:

• Some group, track and file names may not be displayed correctly

depending on recording conditions.

• The order of groups, tracks and files may be displayed differently

from the order displayed on your personal computer.

1 Press ON SCREEN twice.

2 P^Thr^ee^os^n-s^scrC^eeuⁿr^bs^aro^ar^pp3^ears/2^{on th}t^eo^Th^Vi^sg^crh^eelⁿig^.ht

3 Press ENTER.

Resume playback

When Resume Playback is set to “ON” (see

page 30) and you stop playback by the

following operations, the position where

playback has been stopped is stored.

(“RESUME” appears on the display

window.)

4 Press Cursor Y/5 to select the desired

view angle.

• Turning off the power (see page 10)

• Pressing 7 once

5 Press ENTER.

• Changing the source (see page 11)

6 Press ON SCREEN.

The on-screen bar disappears.

To start playback from the stored position

(“RESUME” disappears.)

• Press 3 (play button) on the remote control or the center unit.

• Select DVD as the source again if you changed the source.

To clear the stored position

Press 7 again or open the disc tray.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

Selecting the subtitle

7 During playback of a disc

containing subtitles in several

languages

Selecting the audio

7 During playback of a disc containing

audio in several languages

When using the AUDIO button:

When using the SUBTITLE button:

1 Press AUDIO.

1 Press SUBTITLE.

Example (DVD VIDEO):

“ENGLISH” is selected out of 3 audio languages recorded.

“ENGLISH” is selected out of 3 subtitle languages recorded.

2 Press AUDIO repeatedly or Cursor Y/5

2 Press Cursor Y/5 to select the desired

to select the desired audio.

subtitle.

When using the on-screen bar:

For DVD VR

• Pressing SUBTITLE activates the subtitles (subpictures)

regardless of whether the subtitles are recorded or not.

(Subpictures will not change if no subpicture is recorded.)

1 Press ON SCREEN twice.

2 P^Thr^ee^os^n-s^scrC^eeuⁿr^bs^aro^ar^pp3^ears/2^{on th}t^eo^Th^Vi^sg^crh^eelⁿig^.ht

3 Press ENTER.

For SVCD

• An SVCD can contain up to four subtitles. Pressing

SUBTITLE changes the subtitles regardless of whether the

subtitles are recorded or not. (Subtitles will not change if no

subtitle is recorded.)

NOTE

• Each time you press SUBTITLE, the subtitle appears and

disappears alternately.

4 Press Cursor Y/5 to select the desired

audio.

When using the on-screen bar:

5 Press ENTER.

1 Press ON SCREEN twice.

2 P^Thr^ee^os^n-s^scrC^eeuⁿr^bs^aro^ar^pp3^ears/2^{on th}t^eo^Th^Vi^sg^crh^eelⁿig^.ht

3 Press ENTER.

6 Press ON SCREEN.

The on-screen bar disappears.

NOTE

• Some subtitle or audio languages are abbreviated in the pop-up

window. See “The language codes list”. (See page 28.)

• “ST”, “L” and “R” is displayed when playing a DVD VR, VCD or

SVCD respectively representing “stereo”, “left sound” and “right

sound”.

4 Press Cursor Y/5 repeatedly to select

the desired subtitle.

5 Press ENTER.

6 Press ON SCREEN.

The on-screen bar disappears.

NOTE

• Some subtitle or audio languages are abbreviated in the pop-up

window. See “The language codes list”. (See page 28.)

• Each time you press SUBTITLE, the subtitle appears and disappears

alternately.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

Changing the VFP setting

The VFP (Video Fine Processor) function

enables you to adjust the picture character

according to the type of programming,

picture tone or personal preference.

Special picture playback

Frame-by-frame playback

7 During playback

Press 8 repeatedly.

Each time you press the button, the still

picture advances by one frame.

1 Press VFP.

The current VFP settings appear on the TV screen.

Example:

To return to normal playback

Press DVD/CD3.

Playing back in slow-motion

7 During playback

1 Press 8 at the point

2 Press Cursor 3/2 repeatedly to select

where you want to start

playback in slow-motion form.

the VFP mode.

• NORMAL:Normally select this.

• CINEMA: Suitable for movies.

When you select “NORMAL” or “CINEMA”, press VFP to

complete the setting.

• USER 1 and USER 2:

2 P^Thr^ee^ss^yss^temS^pL^aO^useW^{s playback.}

• Playback in forward slow-motion starts.

You can adjust parameters that affect picture appearance.

For DVD VIDEO only:

• To play back in reverse slow-motion, press SLOW

Only when selecting “USER 1” or “USER 2” in step

2, proceed to perform the following operation;

Each time you press the button, the playback speed become

faster.

3 Press Cursor Y/5 repeatedly to select

To return to normal playback

Press DVD/CD3.

a parameter you want to adjust.

Adjust gradually and confirm picture appearance results are as

preferred.

NOTE

• GAMMA:

• Sound cannot be heard during slow-motion playback.

Controls brightness of neutral tints while maintaining

brightness of dark and bright portions.

• BRIGHTNESS:

Controls screen brightness.

• CONTRAST:

Zooming in

7 During playback or while paused

Controls screen contrast.

• SATURATION:

Controls screen color depth.

• TINT:

Controls screen tint.

• SHARPNESS:

1 Press ZOOM, with SHIFT

pressed.

Each time you repeat the procedure,

2 ^tW^heh^sci^elⁿe^ez^mo^agoⁿⁱm^fice^atd^ionin^ch,^ap^ngr^ee^s.ss Cursor 3/2/Y/

Controls screen sharpness.

5 to move zoom-in area.

To return to normal playback

Press ZOOM repeatedly, with SHIFT pressed to select OFF.

NOTE

• The number of the magnification steps varies depending on the disc

type.

• During slide-show playback of JPEG, zooming in is not available. In

such a case, press 8 to pause slide-show playback, then zoom in.

• During JPEG playback, there may be a case where Cursor (3/2/Y/

5) does not work in step 2.

Continued on next page

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

To clear the programs one by one from the last

entered number

Press CANCEL repeatedly.

4 Press ENTER.

Example:

To clear all programs

Press 7.

You can also clear the program by turning off the system.

5 Press Cursor Y/5 to change the

3 Press DVD/CD3 to start Program

setting.

Playback.

6 Press ENTER.

If all of the programmed tracks/files have been played back,

playback stops and the program window appears again. Note

that program setting remains.

7 ^TR^he^ep^cue^rra^ent^ts^Vt^Fe^Pp^ses^ttin3^gsto^app6^eat^ro^agaaⁱⁿd^.just other

To check the program contents

During playback, press 7. Playback stops and the program window

appears.

parameters.

8 Press VFP.

To quit the Program mode

While stopped, press PLAY MODE repeatedly until both program

window and “RANDOM” disappears from the TV screen.

NOTE

• Although the setting display disappears in the middle of the

procedure, the setting at that time will be stored.

NOTE

• The Resume function cannot be used with Program Playback.

• Program Playback may not work for some discs.

Program playback

7 While stopped

Random playback

You can play titles or tracks

on a disc in random order.

1 Press PLAY MODE repeatedly until

program window appears on the TV

screen.

7 While stopped

1 Press PLAY MODE repeatedly until

“RANDOM” appears on the TV screen.

2 Press 3 (play button).

After playing all titles/tracks on the disc, the system stops

playback and quits the Random mode.

To quit the Random mode

USE NUMERIC KEYS TO PROGRAM TRACKS.

USE CANCEL TO DELETE THE PROGRAM.

While stopped, press PLAY MODE repeatedly until both program

window and “RANDOM” disappear from the TV screen.

You can also clear the Random mode by turning off the system.

2 Follow the instructions that appear on

the TV screen to program the desired

chapters/tracks.

NOTE

• The same title/track will not be played back more than once during

Random Playback.

• For details on using the number buttons, see “How to use the

number buttons”. (See page 15.)

• The content’s numbers that you have to specify for

programming varies depending on the disc type:

•

DVD VIDEO:

VCD, SVCD, CD:

MP3:

Titles and chapters

Tracks

Groups and tracks

• You can specify the chapters/tracks whose number is up to

99.

• (For CD, SVCD or VCD) When the total playback time

exceeds 99 minutes 59 seconds, “–:–” will appear on the

display window. But, it is possible to continue

programming.

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

When using the on-screen bar (except for MP3/

JPEG):

Repeat playback

1 Press ON SCREEN twice.

Repeating the current selection

2 P^Thr^ee^os^n-s^scrC^eeuⁿr^bs^aro^ar^pp3^ears/2^{on th}t^eo^Th^Vi^sg^crh^eelⁿig^.ht

3 Press ENTER.

7 For DVD VIDEO/DVD VR:

During playback

For VCD/SVCD:

During playback without PBC

function or stopped

For CD/MP3/JPEG:

During playback or stopped

When using the REPEAT button:

4 Press Cursor Y/5 repeatedly to select

Press REPEAT, with SHIFT pressed.

the Repeat mode.

5 Press ENTER.

: 3

1 2_.

6 Press ON SCREEN.

The on-screen bar disappears.

Repeat mode indicator

To cancel Repeat Playback

Each time you press REPEAT, the Repeat mode changes.

Select “OFF” in step 4.

Display

window

TV screen

Meanings

Repeating a desired part [A-B Repeat]

You can repeat playback of a desired part by

specifying the beginning (point A) and

ending (point B).

Repeats the current group for

MP3/JPEG.

REPEAT GROUP

Repeats the current title for

DVD VIDEO.

7 During playback

Repeats the current title for

Original program for DVD VR.

When using the A-B RPT button:

Repeats the current playlist for

Playlist for DVD VR.

1 Press A-B RPT, with SHIFT pressed at

the beginning of the part you want to

repeat (point A).

Repeats all title/tracks/files for

DVD VR/VCD/SVCD/CD/

MP3/JPEG.

ALL

REPEAT ALL

The repeat mode indicator “

” appears on the display

2 ^wPⁱrⁿe^dos^ws^.A-B RPT again, with SHIFT

Repeats the current track for

VCD/SVCD/CD/MP3.

REPEAT TRACK,

REPEAT STEP

pressed at the end of the part you want

Repeats the current chapter for

DVD VIDEO/DVD VR.

to repeat (point B).

The repeat mode indicator on the display window changes to

REPEAT STEP

“

” and A-B Repeat Playback starts. The selected

Repeat mode is off.

The system plays back the disc

normally.

indication

part of the disc (between point A and B) is played repeatedly.

NOTE

• For DVD VIDEO, REPEAT ALL may not be available depending on

the disc.

To cancel

Press A-B RPT, with SHIFT pressed during A-B Repeat Playback.

Continued on next page

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 17 for button locations.

Advanced operations

When using the on-screen bar:

Balance setting

You can adjust the balance between the front left and front right

speakers.

1 Press ON SCREEN twice.

2 P^Thr^ee^os^n-s^scrC^eeuⁿr^bs^aro^ar^pp3^ears/2^{on th}t^eo^Th^Vi^sg^crh^eelⁿig^.ht

3 Press ENTER.

NOTE

• This function also takes effect for the sources other than DVD.

• Before you start operation;

There is a time limit when doing the following steps. If the setting is

cancelled before you finish, start from step 1 again.

1 Press SETTING, with SHIFT pressed.

4 Press Cursor Y/5 repeatedly to select

Example:

“A-B”.

B A L C T R

5 Press ENTER at the beginning of the

part you want to repeat (point A).

2 Press Cursor 3/2 to make an

adjustment or selection.

Example:

6 Press ENTER at the end of the part you

B A L

want to repeat (point B).

7 ^AP^-r^Be^Rs^es^peO^{at P}N^layS^bC^ackR^sE^tarE^tsN^..

The adjustment display automatically disappears a few

seconds later with the current setting.

The on-screen bar disappears.

To cancel

Select “OFF” in step 4, then press ENTER.

NOTE

• When playing back a DVD VIDEO, A-B Repeat Playback is possible

only within the same title.

• “A-B” cannot be selected during Program and Random Playback.

• “A-B” cannot be selected during playback with PBC function.

Tray lock

You can lock the tray and prohibit the unwanted disc ejection.

On the center unit ONLY:

While the system is on standby mode, press 0 , with 7 pressed

and held.

Press and hold

• The system turns on and “LOCKED” appears on the display

window.

• If you try to eject the disc, “LOCKED” appears to indicate that

the tray is locked.

To cancel

Carry out the same operation again.

• The system turns on and “UNLOCKED” appears on the display

window.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting DVD preferences

NOTE

Using the setup menus

• You can change the language used in the setup menus. See

• See the following “The language codes list” for the code of each

language, such as “AA”, etc.

“Menu description”.

The language codes list

Basic operation on the setup menus

AA Afar

IK Inupiak

IN Indonesian

IS Icelandic

IW Hebrew

RN Kirundi

RO Rumanian

RU Russian

RW Kinyarwanda

SA Sanskrit

SD Sindhi

TOP MENU/PG

SET UP

MENU/PL

SETTING

AB Abkhazian

AF Afrikaans

AM Ameharic

AR Arabic

ENTER

Cursor

(3/2/Y/5)/

FL DISPLAY

DVD/CD

ON SCREEN

ENTER

Yiddish

AS Assamese

AY Aymara

AZ Azerbaijani

BA Bashkir

BE Byelorussian

BG Bulgarian

BH Bihari

JW Javanese

MEMORY FM MODE RETURN

KA Georgian

KK Kazakh

SG Sangho

TUNING

SLOW

SH Serbo-Croatian

SI Singhalese

SK Slovak

ANGLE

ZOOM

KL Greenlandic

KM Cambodian

KN Kannada

KO Korean (KOR)

KS Kashmiri

FM/AM

TITLE/

AUX

AUDIO SUBTITLE

GROUP PLAY MODE CANCEL MUTING

SL Slovenian

SM Samoan

SN Shona

BASS/

SCAN MODE TREBLE

TV CHANNEL

VFP

BI Bislama

SHIFT SPK-LEVEL

BN Bengali, Bangla KU Kurdish

SO Somali

LEVEL AUDIO VOL

BO Tibetan

BR Breton

CA Catalan

CO Corsican

CS Czech

KY Kirghiz

LA Latin

SQ Albanian

SR Serbian

SS Siswati

7 While stopped

LN Lingala

LO Laothian

LT Lithuanian

1 Press SET UP, with SHIFT pressed.

ST Sesotho

SU Sundanese

CY Welsh

LV Latvian, Lettish SV Swedish

DA Danish

DZ Bhutani

EL Greek

MG Malagasy

MI Maori

SW Swahili

TA Tamil

MK Macedonian

ML Malayalam

MN Mongolian

MO Moldavian

MR Marathi

TE Telugu

TG Tajik

EO Esperanto

ET Estonian

EU Basque

FA Persian

FI Finnish

FJ Fiji

TH Thai

TI Tigrinya

TK Turkmen

TL Tagalog

TN Setswana

TO Tonga

TR Turkish

TS Tsonga

TT Tatar

2 Follow the instructions that appear on

MS Malay (MAY)

MT Maltese

the TV screen.

FO Faroese

FY Frisian

GA Irish

MY Burmese

NA Nauru

NE Nepali

Menu description

GD Scots Gaelic

GL Galician

GN Guarani

GU Gujarati

HA Hausa

NL Dutch

NO Norwegian

OC Occitan

TW Twi

UK Ukrainian

UR Urdu

:Language menu (LANGUAGE)

OM (Afan) Oromo

OR Oriya

UZ Uzbek

VI Vietnamese

VO Volapuk

WO Wolof

XH Xhosa

YO Yoruba

7 MENU LANGUAGE

HI Hindi

PA Panjabi

Some DVDs have their own menus in multiple languages.

• Select the initial menu language*.

HR Croatian

HU Hungarian

HY Armenian

IA Interlingua

IE Interlingue

PL Polish

PS Pashto, Pushto

PT Portuguese

QU Quechua

7 AUDIO LANGUAGE

Some DVDs have multiple audio languages.

• Select the initial audio language*.

RM Rhaeto-Romance ZU Zulu

7 SUBTITLE

Some DVDs have multiple subtitle languages.

• Select the initial subtitle language*.

7 ON SCREEN LANGUAGE

• Select the language shown on the TV screen when operating this

system.

* When the language you have selected is not recorded to a disc,

the original language is automatically used as the initial

language.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting DVD preferences

:Audio menu (AUDIO)

:Picture menu (PICTURE)

7 D. RANGE COMPRESSION

7 MONITOR TYPE

(Dynamic range compression)

You can select the monitor type to match your TV when you play

DVDs recorded in the picture’s height/width ratio of 16:9.

• 16:9 (Wide television conversion)

You can enjoy low level recorded sound clearly at night even at a

low volume when listening to the sound with Dolby Digital.

• AUTO

Select this when the aspect ratio of your TV is 16:9 (wide

TV).

• 4:3 LB (Letter Box conversion)

Select this when you want to enjoy surround sound with its

full dynamic range (no effect applied).

• ON

Select this when you want to fully apply the compression

effect (useful at midnight).

Select this when the aspect ratio of your TV is 4:3

(conventional TV). While viewing a wide screen picture, the

black bars appear on the top and the bottom of the screen.

• 4:3 PS (Pan Scan conversion)

Select this when the aspect ratio of your TV is 4:3

(conventional TV). While viewing a wide screen picture, the

black bars do not appear, however, the left and right edges of

the pictures will not be shown on the screen.

NOTE

• When you play a multichannel Dolby Digital source with the

surround mode is off, the setting of D. RANGE COMPRESSION is

set to ON automatically.

Ex.: 16:9

Ex.: 4:3 LB

Ex.: 4:3 PS

NOTE

• Even if “4:3 PS” is selected, the screen size may become “4:3 LB”

with some DVDs. This depends on how DVDs are recorded.

7 PICTURE SOURCE

You can obtain optimal picture quality by selecting whether the

content on the disc is processed by field (video source) or by frame

(film source).

Normally set to “AUTO”.

• AUTO

Used to play a disc containing both video and film source

materials.

This system recognizes the source type (video or film) of the

current disc according to the disc information.

• If the playback picture is unclear or noisy, or the oblique

lines of the picture are rough, try to change to other modes.

• FILM

Suitable for playing back a film source disc.

• VIDEO

Suitable for playing back a video source disc.

7 SCREEN SAVER (See page 15.)

You can activate or deactivate Screen Saver function.

7 FILE TYPE

When several types of files are recorded on a disc, you can select

which files to play.

• AUDIO

Select this to play MP3 files.

• STILL PICTURE

Select this to play JPEG files.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting DVD preferences

:Speaker setting menu

(SPK. SETTING)

:Other setting menu (OTHERS)

7 RESUME (See page 22.)

You can activate or deactivate Resume Playback function.

7 Level menu (LEVEL)

FRONT LEFT SPEAKER/FRONT RIGHT SPEAKER/

CENTER SPEAKER/SURROUND RIGHT SPEAKER/

SURROUND LEFT SPEAKER

7 ON SCREEN GUIDE

You can activate or deactivate the on-screen guide icons. (See page

13.)

While monitoring the test tone, adjust the output level of the

speakers.

You can adjust the output level in the -6 dB to +6 dB range.

TEST TONE*

Outputs the test tone.

* The test tone comes out of all of the activated speakers in the

following sequence:

s Front left speaker s Center speaker s Front right

speaker s Surround right speaker s Surround left

speaker s (back to the beginning)

7 Delay menu (DELAY)

Example:

Center

speaker

1 ms

Subwoofer

Front right

0 ms

Front left

0 ms

Surround left

2 ms

Surround right

2 ms

In this case, set the delay time of each speaker as follows;

• Delay time of front speakers: 0 ms

• Delay time of center speaker: 1 ms

• Delay time of surround speakers: 2 ms

FRONT LEFT SPEAKER/FRONT RIGHT SPEAKER/

CENTER SPEAKER/SURROUND RIGHT SPEAKER/

SURROUND LEFT SPEAKER

Adjust the distance from the listening position to the speakers.

Within the range from 0 ms to 15 ms. (by 1 ms)

7 Subwoofer menu (SUBWOOFER)

LEVEL

You can set the output level of the subwoofer in the -6 dB to +6 dB

range.

CROSS OVER

The signals below the preset frequency level will be sent to and be

reproduced by the subwoofer.

Select one of the cross over frequency levels according to the bass

sound quality from the front/center/surround speakers.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner operations

The buttons described below are used on pages 31 and

32.

Manual tuning

REPEAT

A-B RPT

SLEEP

1 ^{Press FM/AM repeatedly to select the}

band.

Number

buttons

TV/VIDEO

Example:

When the system is tuned in to 810 kHz.

DIMMER

SURROUND

MENU/PL

TOP MENU/PG

0 _kHz

SET UP

SETTING

ENTER

FL DISPLAY

DVD/CD

2 Press TUNING 9/( repeatedly until

ON SCREEN

you find the frequency you want.

MEMORY FM MODE RETURN

When you hold down the button until the system starts

searching for stations and then release it, the system stops

searching automatically when a station of sufficient signal

strength is tuned in to.

TUNING

SLOW

ANGLE

ZOOM

AUDIO SUBTITLE

FM/AM

TITLE/

AUX

NOTE

GROUP PLAY MODE CANCEL MUTING

• When an FM stereo program is received, the ST indicator lights on the

display window.

BASS/

TV CHANNEL

SCAN MODE TREBLE

VFP

SHIFT SPK-LEVEL

Download from Www.Somanuals.com. All Manuals Search And Download.

See page 31 for button locations.

Tuner operations

Preset tuning

Once a station is assigned to a channel number, the station can be

quickly tuned in. You can preset 30 FM and 15 AM stations.

Selecting the FM

reception mode

When the stereo FM program currently tuned in is noisy, you can

change the FM reception mode to improve the reception.

7 To preset the stations

7 While listening to an FM station

Press FM MODE.

The FM reception mode appears on the display window.

Each time you press the button, the FM reception mode changes.

• AUTO:

When a program is broadcast in stereo, you will hear stereo

sound. (The ST indicator lights on the display window.) When in

monaural, you will hear monaural sound. This mode is also

useful to suppress static noise between stations.

• MONO:

1 Tune in the station you want to preset.

• If you want to store the FM reception mode for an FM

station, select the reception mode you want. See “Selecting

the FM reception mode”.

Example:

When the system is tuned in to 103.5 MHz.

MHz

1 0 3 5

Reception will be improved although you will lose the stereo

effect. (The MONO indicator lights on the display window.) In

this mode, you will hear noise until you are tuned in to a station.

2 Press MEMORY.

MHz

_CH_ _

1 0 3

While “– –” are flashing:

3 Press number button(s) (1-10, +10) to

select a preset number you want.

• For details on using the number buttons, see “How to use the

number buttons”. (See page 15.)

Example:

When the preset channel 1 is selected.

MHz

3 5

If the setting is cancelled before you finish, start from step 2

again.

While the selected number is flashing:

4 Press MEMORY.

The selected number stops flashing.

The station is assigned to the selected preset number.

If the setting is cancelled before you finish, start from step 2

5 ^aR^gaeⁱⁿp^.eat steps 1 to 4.

• Storing a new station to a used number erases the previously

stored one.

7 To tune in to a preset station

1 Press FM/AM repeatedly to select FM or

AM.

2 Press number button(s) (1-10, +10) to

select a preset number.

• For details on using the number buttons, see “How to use the

number buttons”. (See page 15.)

Download from Www.Somanuals.com. All Manuals Search And Download.

References

To clean the disc

Wipe the disc with a soft cloth in a straight

line from center to edge.

Maintenance

• DO NOT use any solvent — such as

conventional record cleaner, spray,

thinner or benzine — to clean the

disc.

7 Handling Discs

• Remove the disc from its case by holding it

at the edge while pressing the center hole

lightly.

• Do not touch the shiny surface of the disc

or bend the disc.

• Put the disc back in its case after use to

prevent warping.

7 Cleaning the system

• Stains on the system should be wiped off with a soft cloth. If the

system is heavily stained, wipe it with a cloth soaked in water

diluted neutral detergent and wrung well, then wipe clean with a

dry cloth.

• Be careful not to scratch the surface of the

disc when placing it back in its case.

• Avoid exposure to direct sunlight,

temperature extremes and moisture.

• Since the system may deteriorate in quality, become damaged or

get its paint peeled off, be careful about the following.

•

DO NOT wipe it with a hard cloth.

DO NOT wipe it strong.

DO NOT wipe it with thinner or benzine.

DO NOT apply any volatile substance such as insecticides to it.

DO NOT allow any rubber or plastic to remain in contact with

it for a long time.

Troubleshooting

PROBLEM

POSSIBLE CAUSE

The power cord is not connected.

SOLUTION

Power does not come

on.

Connect the power cord correctly. (See page 8.)

The remote control does The batteries are exhausted.

not work.

Replace the batteries. (See page 5.)

Sunlight is falling directly on the remote sensor.

Hide the remote sensor from direct sunlight.

The remote control does The remote control mode is not for the desired source. Before operation, press one of the source selecting

not work as expected.

buttons for the desired source.

No sound.

The speaker cord is not connected.

Check the connection. (See page 7.)

Select the correct source. (See page 11.)

Connect the cable correctly. (See page 8.)

Use a playable disc. (See page 3.)

An incorrect source has been selected.

No picture is displayed The video cable is not connected correctly.

on the TV screen.

The disc is not playable.

No picture is displayed The scan mode is set to “PROGRESS” though the

Change the scan mode to “INTER,”. (See page 12.)

on the TV screen, the

center unit is connected to the TV which does not

picture is blurred, or the support the progressive video input.

picture is divided into

two parts.

Video and audio are

distorted.

The disc is scratched or dirty.

Replace or clean the disc.

A VCR is connected between the center unit and the

TV.

Connect the center unit and TV directly. (See page 8.)

The picture does not fit The monitor type is not set correctly.

the TV screen.

Set “MONITOR TYPE” properly. (See page 29.)

Hard to listen to

broadcast because of

noise.

Antennas are disconnected.

Reconnect the antennas correctly and securely. (See

page 6.)

The system suddenly

turns off.

The playback level of the current source is too high.

Play back the source with lower volume level.

Download from Www.Somanuals.com. All Manuals Search And Download.

References

7 Front speakers (SP-THS11BF)

Specifications

Type:

1-Way Bass-Reflex Type

(Magnetically-shielded Type)

Speaker:

Power Handling Capacity: 33 W

Impedance:

Frequency Range:

Sound Pressure Level:

Dimensions (W M H M D):

8.0 cm cone M 1

Center unit (XV-THS11B)

Audio section

6 C

Front/Center/Surround: 33 W per channel, RMS at 6 C at 1 kHz,

90 Hz to 20 000 Hz

84 dB/W·m

with 10% total harmonic distortion.

Subwoofer:

40 W, RMS at 4 C at 100 Hz, with 10%

total harmonic distortion.

92 mm M 101 mm M 95 mm

Video section

Video System:

Mass:

0.58 kg each

NTSC

Horizontal Resolution: 500 lines

7 Center speaker (SP-THS11BC)

Signal-to-Noise Ratio:

Video output level

Composite:

64 dB

Type:

1-Way Bass-Reflex Type

(Magnetically-shielded Type)

1.0 V(p-p)/75 C

0.286 V(p-p)/75 C

Speaker:

Power Handling Capacity: 33 W

8.0 cm cone M 1

S-video-Y:

S-video-C:

Impedance:

6 C

Component (Interlace/Progressive):

Frequency Range:

Sound Pressure Level:

Dimensions (W M H M D):

90 Hz to 20 000 Hz

85 dB/W·m

P^B/PR:

1.0 V(p-p)/75 C

0.7 V(p-p)/75 C

Tuner section

Tuning Range

FM:

92 mm M 101 mm M 95 mm

Mass:

0.65 kg

87.5 MHz to 108.0 MHz

530 kHz to 1 710 kHz

AM:

7 Surround speakers (SP-THS11BS)

Speaker impedance

Front/Center/Surround: 6 C to 16 C

Type:

Speaker:

Power Handling Capacity: 33 W

1-Way Bass-Reflex Type

8.0 cm cone M 1

Subwoofer:

4 C to 16 C

Impedance:

Frequency Range:

Sound Pressure Level:

Dimensions (W M H M D):

6 C

General

Power Requirements:

Power Consumption:

90 Hz to 20 000 Hz

82 dB/W·m

AC 120 V

135 W (at operation)

1.3 W (in standby mode)

, 60 Hz

92 mm M 101 mm M 95 mm

Dimensions (W M H M D):

360 mm M 65 mm M 370 mm

5.3 kg

Mass:

0.56 kg each

Mass:

7 Subwoofer (SP-THS11BW)

Type:

1-Way Bass-Reflex Type

15.0 cm cone M 1

Speaker:

Power Handling Capacity: 40 W

Impedance:

4 C

Frequency Range:

Sound Pressure Level:

Dimensions (W M H M D):

40 Hz to 1 800 Hz

84 dB/W·m

129 mm M 284 mm M 337 mm

Mass:

3.0 kg

Designs & specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

0507YAMMDWJMM

Download from Www.Somanuals.com. All Manuals Search And Download.

Insignia Portable DVD Player NS P8DVD User Manual
Invacare Mobility Aid TRHD22HR User Manual
ITT Heat Pump GT07 User Manual
Jensen Car Stereo System BT1613 User Manual
Johnson Controls Air Conditioner CSV060B 240B User Manual
JVC Camcorder 0206ASR NF VM User Manual
Kenwood Stereo System TK 2180 User Manual
Keurig Coffeemaker 108553 User Manual
KitchenAid Ventilation Hood KBRA20EMWH00 User Manual
Kramer Electronics TV Cables VA 4H User Manual