LCD Flat Television Users Guide
For Models:
LT-37X776
LT-32X776
LT-26X776
Illustration of LT-32X776 and RM-C14G
Important Note:
In the spaces below, enter the model and serial number of your television (located at the
rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this
guide. Keep this user’s guide in a convenient place for future reference. Keep the carton
and original packaging for future use.
Model Number:
LCT1881-001A-A
0405TNH-II-IM
Serial Number:
Download from Www.Somanuals.com. All Manuals Search And Download.
This product incorporates copyright protection technology that is protected by U.S. patents
and other intellectual property rights. Use of this copyright protection technology must
be authorized by Macrovision, and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is
prohibited.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
16) Avoid improper installation and never position the unit where good ventilation is impossible. When
installing this TV, distance recommendations must be maintained between the set and the wall,
as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance
guidelines shown for safe operation.
200 mm
200 mm
50 mm
150 mm
150 mm
17) Cautions for installation
— Do not tilt the TV towards the left or right, or towards the back.
— Install the TV in a corner on the floor so as to keep cords out of the way.
— The TV will generate a slight amount of heat during operation. Ensure that sufficient space is
available around the TV to allow satisfactory cooling.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Avoiding Ghost Images
Displaying fixed images for extended periods of time can leave a subtle but temporary ghost
image on your screen. To avoid this, mix your viewing pattern.
Examples include, but are not limited to the following:
For example...
• Stock-market report bars
• Shopping channel logos and pricing
displays
TV on
TV off
• Video game patterns or scoreboards
• Bright station logos
• Internet web sites or other computer-style
images.
• DVD discs, video tapes, laser discs
• Broadcast, cable, satellite channels or
digital television tuners/converters.
XYZ
XYZ
Caring for the Cabinet
Normally, light dusting with a soft, non-scratching duster will keep your TV clean.
If you wish to wipe down the television, first unplug it. Then wipe gently with a soft cloth, slightly
moistened with water. You can add a few drops of mild liquid detergent to the water to help
remove spots of oily dirt.
• DO NOT allow liquid to enter the TV through the ventilation slots.
• DO NOT use strong or abrasive cleaners on the TV.
• DO NOT spray liquids or cleaners directly on the TV’s surface.
• DO NOT rub or scrub the TV harshly. Wipe the set gently with a soft cloth.
Caring for the Screen
The screen is treated with an electrostatic-proof coating. When it gets dirty, wipe it gently with a
soft cloth. If the screen is very dirty, wipe it down with a cloth dipped in a diluted kitchen cleaner
and thoroughly wrung-out. Then wipe immediately after with a clean, dry cloth.
Do not apply alcohol, organic solvents (like acetone), acidic or alkaline cleansers to the screen.
These will remove the coating layer and cause discolorations.
Do not push or hit the screen. This could cause scratches on the screen surface and image
distortions.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings (Continued...)
How to move the cabinet
Your fingers may become trapped under
the TV, causing injuries. Hold the TV at the
bottom in the middle, and do not allow the TV
to tilt up or down.
The TV may fall causing injuries. Hold the
bottom of the stand with your hand and tilt
the TV up or down.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Safety Precautions . 2
Warnings . . . . . . . . . . . . 5
Quick Setup . . . . . . . . . . . 9
Unpacking your TV . . . . . . . . . . . . 9
TV Models . . . . . . . . . . . . . . . . 10
TV Remote Control . . . . . . . . . . . 11
Getting Started . . . . . . . . . . . . . 12
Using the Stand . . . . . . . . . . . . 12
The Remote Control . . . . . . . . . . 14
Sound Adjust . . . . . . . . . 56
Sound Settings . . . . . . . . . . . . . 56
Adjust Sound Settings . . . . . . . . . 56
Reset
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
56
Clock Timers . . . . . . . . . . 57
Set Clock . . . . . . . . . . . . . . . . 57
On/Off Timer . . . . . . . . . . . . . . . 58
Button Functions . . . . . . . 59
Multi Screen Function . . . . . . . . . . 59
Index . . . . . . . . . . . . . . . . . . 59
Twin . . . . . . . . . . . . . . . . . 59
Freeze . . . . . . . . . . . . . . . . . . 60
Swap . . . . . . . . . . . . . . . . . 60
Select . . . . . . . . . . . . . . . . . . 60
Power . . . . . . . . . . . . . . . . . . 61
Number Buttons . . . . . . . . . . . . . 61
Connecting Your Devices
.
.
.
.
.
.
.
15
Interactive Plug In Menu . . . . . . . . 25
Remote Programming . . . . . 28
Setting CATV, VCR and DVD Codes
.
.
.
28
CATV or Satellite Codes . . . . . . . . 28
VCR Codes . . . . . . . . . . . . . . 29
DVD Codes . . . . . . . . . . . . . . 30
Search Codes . . . . . . . . . . . . . 31
Tune
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
61
Input . . . . . . . . . . . . . . . . . . . 61
TheaterPro D6500K . . . . . . . . . . . 61
Return+/TV . . . . . . . . . . . . . . . 62
Sound . . . . . . . . . . . . . . . . . . 62
Muting . . . . . . . . . . . . . . . . . . 63
Video Status . . . . . . . . . . . . . . . 63
Natural Cinema . . . . . . . . . . . . . . . 63
Sleep Timer . . . . . . . . . . . . . . . 64
ML/MTS . . . . . . . . . . . . . . . . . 64
Display . . . . . . . . . . . . . . . . . 65
C.C. . . . . . . . . . . . . . . . . . . . 65
Onscreen Menus . . . . . . . . 32
Using the Guide . . . . . . . . . . . . . 32
Onscreen Menu System . . . . . . . . . 33
Initial Setup . . . . . . . . . . 35
Auto Tuner Setup . . . . . . . . . . . . 35
Channel Summary . . . . . . . . . . . . 36
V-Chip . . . . . . . . . . . . . . . . . . 38
Set Lock Code . . . . . . . . . . . . . 44
Auto Demo . . . . . . . . . . . . . . . 45
Channel +/-
Volume +/-
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
65
65
Illumination
.
.
.
.
.
.
.
.
.
.
.
.
.
45
.
.
.
Language . . . . . . . . . . . . . . . . 45
Closed Caption . . . . . . . . . . . . . 46
Auto Shut Off . . . . . . . . . . . . . . 48
XDS ID . . . . . . . . . . . . . . . . . 48
Noise Muting . . . . . . . . . . . . . . 49
Front Panel Lock . . . . . . . . . . . . 49
Favorite . . . . . . . . . . . . . . . . . 66
Aspect . . . . . . . . . . . . . . . . . 67
Aspect Ratios
.
.
.
.
.
.
.
.
.
.
.
.
.
68
Menu . . . . . . . . . . . . . . . . . . 68
OK . . . . . . . . . . . . . . . . . . . 68
Back . . . . . . . . . . . . . . . . . . . 68
TV/CATV Slide Switch . . . . . . . . . . 69
VCR/DVD Slide Switch . . . . . . . . . 69
VCR Buttons . . . . . . . . . . . . . . . 69
DVD Buttons . . . . . . . . . . . . . . . 69
Light . . . . . . . . . . . . . . . . . . . 69
V1 Smart Input
Video Input Label
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
50
50
Position Adjustment . . . . . . . . . . . 51
Power Indicator . . . . . . . . . . . . . 51
Video-1 Monitor Out
.
.
.
.
.
.
.
.
.
.
51
Digital-In . . . . . . . . . . . . . . . . . 52
Digital-In Audio . . . . . . . . . . . . . 52
Picture Adjust . . . . . . . . . 53
Picture Settings . . . . . . . . . . . . . 53
Adjust Picture Settings . . . . . . . . . 53
Color Temperature . . . . . . . . . . . . 53
Digital Noise Clear . . . . . . . . . . . . 54
Color Management
Dynamic Gamma
.
.
.
.
.
.
.
.
.
.
.
.
.
.
54
54
.
.
.
.
.
.
Smart Picture . . . . . . . . . . . . . . 55
Reset . . . . . . . . . . . . . . . . . . 55
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Digital Setup . . . . . . . . . 70
Digital Setup . . . . . . . . . . . . . 70
Antenna Level . . . . . . . . . . . . . 70
Digital Sound . . . . . . . . . . . . . 71
Aspect Ratio . . . . . . . . . . . . . 71
Cable Card Application . . . . . . . . . 72
i.LINK Auto Play . . . . . . . . . . . 72
Software Update . . . . . . . . . . . 72
Digital Button Functions . . . 73
Digital CH D/A (Digital/Analog) . . . . . 73
Sub Channel . . . . . . . . . . . . . 73
i.LINK Menu . . . . . . . . . . . . . . . 74
Controller . . . . . . . . . . . . . 74
Device . . . . . . . . . . . . . . 75
Timer . . . . . . . . . . . . . . . 76
Reservation . . . . . . . . . . . . . . 76
Timer Edit . . . . . . . . . . . . . . 77
Guide . . . . . . . . . . . . . . . 78
OSD Information . . . . . . 79
Weak Signal . . . . . . . . . . . . . 79
No Program . . . . . . . . . . . . . 79
Cable Card Information . . . . 80
Cable Card Connection . . . . . . . . 80
Appendices . . . . . . . . . . 81
Troubleshooting . . . . . . . . . . . . . 81
Warranty
.
.
.
.
.
.
.
.
.
.
.
.
.
.
83
Specifications . . . . . . . . . . . . . 85
Notes . . . . . . . . . . . . . . . . . 86
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Unpacking your TV
Thank you for your purchase of a JVC LCD Flat Television. Before you begin setting up your
new television, please check to make sure you have all of the following items. In addition to
this guide, your television box should include:
Two AA
Batteries
1 Remote Control
1 Television
POWER
TV CATV VCR DVD
ASPECT
MULTI SCREEN
TWIN
INDEX SELECT SLEEP
FREEZE
SWAP ML/MTS DISPLAY
+
INPUT
1
4
2
5
8
0
3
6
D/A
i.LINK MENU
7
9
RETURN+
TV
TIMER
TUNE
THEATER
PRO
VIDEO
STATUS
SUB
CHANNEL
FAVORITE
SUB
NATURAL
CINEMA
SOUND
LIGHT
C.C.
Note: Your television
and/or remote
MUTING
GUIDE
CH
VOL
VOL
OK
CH
control may differ
from the examples
illustrated here.
MENU
BACK
VCR CHANNEL
PREV NEXT
VCR DVD
POWER TV VCR
REW
PLAY
FF
REC
STOP
PAUSE
OPEN CLOSE
STILL PAUSE
RM-C14G
2-WAY SPLITTER
Two Way Splitter x 1
RF Cable × 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
TV Models
NOTE: Before you connect your television to another device, please refer to the proper
diagrams for your specific TV and remote. These will help assist you in understanding
how to connect your television to another device, as well as use the remote to set up
your television.
Rear Panel Diagram
75Ω
(VHF/UHF)
75Ω
(VHF/UHF)
S-VIDEO
VIDEO
R
-
AUDIO
-
L
S-VIDEO
VIDEO
R
-
AUDIO
-
L
NPUT1
I
ATSC
/
DIGITAL CABLE IN
VIDEO
R
-
AUDIO
-
L
Y
Pr
R
Pb
DIGITAL-IN
-
AUDIO
-
L
CABLE CARD
S-VIDEO
VIDEO
i
.
L
I
N
K
I
N
/
O
U
T
S400(TS)
R
-
AUDIO
-
L
NPUT2
I
OPTICAL OUT
Digital Audio
SC
AT
/
CABLE IN
AL
DIGIT
INPUT3
DIGITAL-IN
IU1CMPOENT
GTLNAUDIO
CABLE CARD
MNI/RECOUT
ADIOUT
Side Panel Diagram
POWER
PROGRAM/TIMER
Illumination Lamp
(Page 45)
POWER
PROGRAM/TIMER
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
TV Remote Control
POWER
TV CATV VCR DVD
ASPECT
MULTI SCREEN
TWIN
INDEX SELECT SLEEP
FREEZE
SWAP ML/MTS DISPLAY
+
INPUT
1
4
2
5
8
0
3
6
D/A
i.LINK MENU
7
9
RETURN+
TV
TIMER
TUNE
THEATER
PRO
VIDEO
STATUS
SUB
CHANNEL
FAVORITE
SUB
NATURAL
CINEMA
SOUND
LIGHT
C.C.
MUTING
GUIDE
CH
VOL
VOL
OK
CH
MENU
BACK
VCR CHANNEL
PREV NEXT
VCR DVD
POWER TV VCR
REW
PLAY
FF
REC
STOP
PAUSE
OPEN CLOSE
STILL PAUSE
RM-C14G
RM-C14G
Notes:
• For information on remote control buttons, see pages 59 - 69 and 73 - 78.
• i.LINK MENU, TIMER, SUB CHANNEL, FAVORITE and GUIDE buttons are for digital
channels. If your TV is connected to an ATSC antenna or Digital Cable, you can use these
buttons.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Getting Started
Getting Started
These quick setup pages will provide you, in four easy steps, with the basic information you
need to begin using your new television right away.
If you have questions, or for more detailed information on any of these steps, please consult
other sections of this manual.
Step 1 - Using the stand
This TV comes with a Table Top Stand already attached.
This stand can be used to adjust the direction of the TV screen 5° up, 10° down and 20° to the
left or right.
These illustrations are for LT-26X776 and LT-32X776. The stand for the LT-37X776 is
different. You can only adjust the direction of the TV screen 20º to the left or right.
Tilt the TV up or down
While holding the bottom of the stand with one hand,
use your other hand to hold the middle of the top of the
TV, and slowly tilt the TV up or down.
• As a safety measure, the stand is constructed so that
it requires a certain amount of force to tilt the TV.
Rotate the TV left or right
While holding the bottom of the stand with one hand,
use your other hand to hold the edge of the panel
and slowly adjust the direction of the TV stand.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Getting Started
Cable Holder
A cable holder which keeps your connection cables tidy is attached on the back of the stand.
Gently squeeze the left and right of the cable holder, and pull it to remove it from the stand.
After putting the cables in the cable holder, attach it to the back of the stand again.
Cable Holder
Illustration of LT-32X776 and LT-26X776
Illustration of LT-37X776
Remove the terminal cover
There are connection terminals behind the covers on the left and right in the back of the TV.
Remove these two covers before connecting an antenna or other devices. The covers can
be removed by removing the hooks. When replacing the covers, place the side of the covers
against the TV and insert the hooks.
Note:
• Leave the terminal covers off if they do not fit properly. Do not force to replace the covers.
Doing so may damage the connection cables and covers.
Illustration of LT-32X776 and LT-26X776
Illustration of LT-37X776
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Getting Started
Step 2 – The Remote Control
Before you can operate your remote control, you
first need to install the batteries (included).
Slide the cover on the back of the remote down
towards the bottom of the remote control. Insert
two batteries (included) carefully noting the “+”
and “–” markings, placing the “–” end in the unit
first. Slide the cover back into place.
When you change the batteries, try to
complete the task within three minutes. If you
take longer than three minutes, the remote
control codes for your VCR, DVD, and/or
cable box/satellite receiver may have to be
reset. See pages 28 - 31.
Key Feature Buttons
The four key feature buttons at the center of the remote can be
used for basic operation of the television. The top and bottom
buttons will scan forward and back through the available
channels. To move rapidly through the channels using
JVC’s Hyperscan feature, press and hold CH+ or CH–. The
channels will zip by at a rate of five channels per second. The
right and left buttons will turn the volume up or down. These
buttons are also marked with four arrows and are used with
JVC’s onscreen menu system. To use the onscreen menus,
press the MENU button.
MUTING
GUIDE
CH
OK
CH
VOL
VOL
MENU
BACK
POWER
Basic Operation
T
Turn the television on and off by pressing the POWER button at the top right corner
of the remote. If this is the first time you are turning on the TV, the interactive
plug-in menu appears.
TV CATV
VCR DVD
• Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if
you need to operate a cable box.
• Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to
DVD to control a DVD player. Please see pages 28 to 31 for instructions on
programming your remote control to operate a cable box, VCR or DVD player.
A
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Step 3 - Connecting your devices
To make these connections, you will use plugs like the ones illustrated below.
S-Video Cable
Component Cables
Composite Cables
Audio Cables
Used to make video
connections with S-Video
VCRs, Camcorders and DVD
players.
Used to connect audio/video
devices like VCRs, DVD players,
stereo amplifiers, game consoles,
etc.
Notes:
• These connections are examples.
• After you are finished connecting your devices, plug the power cord into the nearest power
outlet and turn on the TV.
• If you follow these diagrams and the television does not work properly, contact your local
cable operator.
• To connect a DVD player, see VCR Connection. A DVD player is optional
• If you have a satellite television system, refer to the satellite TV manual.
No VCR Connection
75Ω
(VHF/UHF)
Cable or Antenna
Coaxial Cable
Output
(Attachment)
Two-way Splitter
(Attachment)
C
S
AT
DIGIT
CABLE IN
AL
/
TV Rear Panel
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
VCR Connection
Notes:
• Green, blue and red are the most common colors for DVD cables. Some models may vary
colors. Please consult the user’s manual for your DVD player for more information.
• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete
one set of connections (DVD or audio output) before starting the other to avoid accidentally
switching the cables.
• You may also connect the DVD player to Input 1.
Diagram #1
VCR
Cable or Antenna
Output
IN
IN
OUT
L
R
OUT
Two-Way Splitter
(Attachment)
IN
OUT OUT
OR
Coaxial Cable
(Attachment)
S-VIDEO
Ω
75
VIDEO
(VHF/UHF)
INPUT1
R
-
AUDIO
-
L
S-VIDEO
VIDEO
INPUT2
R
-
AUDIO
-
L
VIDEO
C
S
AT
CABLE IN
AL
DIGIT
I
/
R
-
AUDIO
-
L
Y
TV Rear Panel
Pr
R
Pb
IU1CMPOENT
-
AUDIO
-
L
GTLNAUDIO
Green
Blue
Y
PB
DVD Player (OPTIONAL)
Red
PR
AUDIO OUT
ADIOUT
OUT
R
L
Note:
• If this connection setup does not work for you, try the connection setup on page 17.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Diagram #2
VCR
Cable or Antenna
Output
IN
IN
OUT
IN
Two-Way Splitter
OUT OUT
L
R
OUT
OR
IN
Two-Way Splitter
(Attachment)
OUT OUT
Coaxial Cable
(Attachment)
S-VIDEO
VIDEO
INPUT1
R
-
AUDIO
75Ω
-
L
(VHF/UHF)
S-VIDEO
VIDEO
INPUT2
R
-
AUDIO
-
L
VIDEO
INPUT3
R
-
AUDIO
-
L
C
S
AT
DIGIT
CABLE IN
AL
/
Y
Pr
R
Pb
IU1CMPOENT
TV Rear Panel
-
AUDIO
-
L
GTLNAUDIO
Green
Blue
Y
PB
DVD Player (OPTIONAL)
Red
P
R
AUDIO OUT
ADIOUT
OUT
R
L
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to a Camcorder
You can connect a camcorder to you televison by using the input jacks located on the back of
the television.
TV Rear Panel
S-VIDEO
VIDEO
CAMCORDER
NUPT1
I
OR
R
-
AUDIO
-
L
S-VIDEO
VIDEO
IPNUT2
R
-
AUDIO
-
L
IPNUT3
1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on
the back of the TV, OR connect an S-Video cable from the camcorder to the back of the TV.
2) Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on
the back of the TV.
3) Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on
the back of the TV.
Note:
• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the
LEFT AUDIO IN on the back of the TV.
Headphone Connection
You can connect a pair of headphones to the television
using the headphone jack located on the side of the
television.
1) Plug a headphone jack into the headphone jack on
the television’s side panel.
TV Side Panel
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to an External Amplifier
TV Rear Panel
Speaker
Speaker
S-VIDEO
VIDEO
OVER
Amplifier
R
-
AUDIO
-
L
MNI/RECOUT
ADIOUT
1) Connect a white cable from the LEFT AUDIO OUTPUT on the back of the TV to the
LEFT AUDIO INPUT on the amplifier.
2) Connect a red cable from the RIGHT AUDIO OUTPUT on the back of the TV to the
RIGHT AUDIO INPUT on the amplifier.
Notes:
• Refer to your amplifier’s manual for more information.
• You can use AUDIO OUTPUT for your home theater system.
• DVI analog sound can not be outputted.
Connecting to Monitor/Recording Output Terminal
OR
MNI/RECOUT
ADIOUT
VCR
IN
IN
OUT
OUT
TV Rear Panel
Notes:
• When you make this connection, set the Video-1 Monitor Out menu to ON. See page 51.
• If you are receiving ATSC/Digital Cable signal, it can be outputted to the S-Video output
terminal or Video (composite video) terminal.
• If you are receiving Analog TV signal, it can not be outputted to the S-Video output terminal.
• No signal will be outputted through the S-Video output terminal when you are not viewing
images coming from the composite video input terminal.
• No signal will be outputted through the Monitor/Recording output terminal when you are
viewing images from the component video input.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to an AV Receiver using your television's
V1 Smart Input
By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture
sources from many different devices, without having to change or use the other input
connections on your TV. This allows you to free up the other input connections so you can
connect more devices to your television.
TV Rear Panel
S-VIDEO
VIDEO
OVER
NPUT1
I
R
-
AUDIO
-
L
S-VIDEO
VIDEO
OVER
NPUT2
I
R
-
AUDIO
-
L
VIDEO
AV Receiver
INPUT3
R
-
AUDIO
-
L
MONITOR
OUT
Y
Y
Pr
R
Pb
IU1CMPOENT
-
AUDIO
-
L
GTLNAUDIO
MOOR OUT
S-VIDEO
VIDEO
OVER
R
-
AUDIO
-
L
MNI/RECOUT
ADIOUT
1) Connect an S-Video Cable from the AV Receiver's MONITOR OUT, to the S-Video INPUT-1
on the back of your television.
2) Connect a Yellow Composite Cable from the AV Receiver's MONITOR OUT, into the VIDEO
INPUT-1 on the back of your television.
3) Connect a Green Component Cable from the AV Receiver's Y MONITOR OUT, into the Y
VIDEO INPUT-1 on the back of your television.
4) Connect a Blue Component Cable from the AV Receiver's PB MONITOR OUT, into the Pb
VIDEO INPUT-1 on the back of your television.
5) Connect a Red Component Cable from the AV Receiver's PR MONITOR OUT, into the Pr
VIDEO INPUT-1 on the back of your television.
Notes:
• Please refer to your AV Receiver instruction manual for more information on connecting your
speakers and other devices like a DVD player.
• Use your AV Receiver's remote to switch to the different devices you have connected.
• Some AV Receivers may not respond when the V1 Smart Input function is turned on.
• If you have video connections for each input device connected to your AV Receiver, you
should not connect them using both S-Video and Composite connection at the same time
when you are using V1 Input as the V1 Smart Input. In this case we recommend using the
S-Video connection.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to a Digital TV Receiver
By connecting a Digital TV Receiver, high definition pictures can be displayed on your TV in
their digital form.
IPNUT2
TV Rear Panel
VIDEO
DTV Decoder
IPNUT3
R
-
AUD
IO
-
L
Y
Pr
R
DIGITAL OUT
AUDIO OUT
Pb
IU1CMPOENT
L
R
-
AUDIO
-
L
GLTNAUDIO
DIG
AIDOUT
ARD
C
CABLE
HDMI to DVI Cable
After the connections have been made,
tighten the screw to secure the cables.
TV Rear Panel
1) Connect the HDMI to DVI Cable from the DIGITAL OUT on the back of your DTV decoder, to
the DIGITAL-IN on the back of your television.
2) Connect a red cable from the DTV decoder RIGHT AUDIO OUT, to the RIGHT AUDIO
DIGITAL-IN on the back of your television.
3) Connect a white cable from the DTV decoder LEFT AUDIO OUT, to the LEFT AUDIO
DIGITAL-IN on the back of your television.
• The digital-in terminal is not compatible with the picture signal of a personal computer.
• Use a HDMI to DVI cable (commercially available) in order to digitally connect the television
with a DTV decoder.
Notes:
• If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance
may be slightly shifted. Access the “DIGITAL-IN” in the initial setup menu to adjust it. (Refer
to page 52.)
• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to
ANALOG. See "DIGITAL-IN AUDIO", page 52.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to a HDMI Compatible Device
By connecting a HDMI compatible device, high definition pictures can be displayed on your
TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI
compatible device.
HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all
digital audio/video interface. HDMI provides and interface between any audio/video source,
such as a set-top box, DVD player, A/V receiver or an audio and/or video monitor, such as a
digital television (DTV).
HDMI Compatible Device
DIGITAL OUT
AUDIO OUT
L
R
D
ARD
C
CABLE
HDMI Cable
TV Rear Panel
1) Connect the HDMI Cable from the DIGITAL OUT on the back of your DTV or HDMI device, to
the DIGITAL-IN on the back of your television.
Notes:
• When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to
DIGITAL. See "DIGITAL-IN AUDIO", page 52.
• Some decoders may not respond depending on the equipment that you have connected
when it is connected to the HDMI.
• If the HDMI output device signal is changed (for example, 480i/60Hz is changed to
480p/60Hz), the screen may turn green and there may be some distortion for a short time
until the signal becomes stable.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting to an amplifier using your optical output
You can connect an amplifier that has an optical digital input terminal by using an optical digital
cable from the optical output. The signal that is output can be PCM or Dolby Digital.
Television Rear Panel
Amplifier
1) Connect the optical cable from underneath the television to the back of the amplifier.
Notes:
• This terminal can only output digital audio.
• In order to use the optical output connection, select PCM or Dolby Digital on Digital Sound in
the Digital Setup Menu. See page 71.
• Refer to your owners manual on using your amplifier.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Connections
Connecting an i.LINK compatible device to the back of
your television
i.LINK is a digital serial interface that allows devices equipped with an i.LINK connector to
exchange digital video signals, digital audio signals and device control signals bi-directionally
over a single cable. (For example, a JVC D-VHS VCR).
i.LINK refers to the IEEE1394-1995 industry specification and extensions thereof. The
is used for products compliant with the i.LINK standard.
logo
This projection television uses a four-pin i.LINK connector to input and output MPEG2 video
signals, audio signals and control signals.
TV Rear Panel
i.LINK Compatible Device
1) Connect the i.LINK cable from underneath the TV to the back of the i.LINK compatible
device.
Notes:
• Use only the S400 i.LINK cable when connection your devices.
• See page 74 on how to select the i.LINK device.
• Refer to your owners manual on using your i.LINK device.
• When recording or playing back video with an i.LINK device, if you perform the Auto Tuner
Setup, the video signal you are recording or playing back may stop or you may not be able
to perform the Digital Auto Tuner Setup.
• Your television can connect with i.LINK D-VHS decks and HD-Camcorders (JVC brand only).
If you connect other brand devices, with i.LINK cable, they will not work.
• It can play only the recorded contents in Digital Mode.
• Use only tapes bearing the DVHS (SVHS) mark for recording.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Plug-In Menu
Step 4 – The Interactive Plug In Menu
When you turn your television on for the first time the interactive plug-in menu will appear. The
plug-in menu helps you to get your TV ready to use by letting you set your preferences for:
• The language in which you want the onscreen menus to appear.
• Setting the TV’s clock to the correct time so your timer functions will work properly. You can
choose “AUTO” or “MANUAL” for setting the clock.
• The auto tuner setup of which channels you wish to receive.
We recommend you complete the interactive plug-in items before you start using your
television.
Notes:
• The interactive plug-in menu setting does not appear if your TV has been turned on before.
In this case use the onscreen menus to perform these settings. See pages 45, 57, 35.
• If you press the Menu button while setting up the interactive plug-in menu, it will skip over it.
Language
After the “JVC INTERACTIVE PLUG IN MENU” has been displayed, the TV automatically
switches to the LANGUAGE settings. You can choose to view your onscreen menus in three
languages: English, French (Français) or Spanish (Español).
LANGUAGE/LANGUE/IDIOMA
è
To choose a language:
(English, Français or Español)
†
To NEXT (To set clock)
ENGLISH
NEXT
MENU
SELECT OPERATE
EXIT
(To be continued...)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Plug-In Menu
Auto Clock Set
Before you use any of your TV’s timer functions, you must first set the clock. You may
precisely set your clock using the XDS time signal broadcast by most public analog
broadcasting stations. If you do not have this in your area, you will have to set the clock
manually. See manual clock set below. To set the clock using the XDS signal:
è
†
To choose AUTO
To TIME ZONE
SET CLOCK
è
To select your time zone: (Atlantic, Eastern,
Central, Mountain, Pacific, Alaska or
Hawaii)
MODE
AUTO
--: ----
TIME
TIME ZONE
DATE/YEAR
D.S.T.
ATLANTIC
JAN/01/05
ON
†
è
†
To move to D.S.T. (Daylight Savings Time)
To turn D.S.T. ON or OFF
To NEXT (To Auto Tuner Setup)
NEXT
MENU
SELECT OPERATE
EXIT
Notes:
• D.S.T. can be used when it is set to ON in the SET CLOCK menu.
• Only when the MODE is set to AUTO, the Daylight Savings Time feature automatically
adjusts your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00
am on the first Sunday in April. The clock will move back one hour at 2:00 am on the last
Sunday in October.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
Manual Clock Set
To set your clock manually (without using the XDS signal), choose MANUAL. If you choose
AUTO, see auto clock set above.
è
†
To choose MANUAL
To TIME
SET CLOCK
è
†
To set the hour
To minute
MODE
MANUAL
è
†
To set the minute
To TIME ZONE
TIME
--: ----
TIME ZONE
DATE/YEAR
D.S.T.
ATLANTIC
JAN/01/05
ON
è
To select your time zone: (Atlantic, Eastern,
Central, Mountain, Pacific, Alaska or
Hawaii)
START CLOCK
SELECT OPERATE
†
è
†
To DATE/YEAR
To set the month
To day
MENU
EXIT
è
†
To set the day
To year
è
†
è
†
To set the year
To move to D.S.T. (Daylight Savings Time)
To turn D.S.T. ON or OFF
To START CLOCK
Note:
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
(To be continued...)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Setup
Plug-In Menu
Auto Tuner Setup
In auto tuner setup, the TV automatically scans through all available channels, memorizing the
active ones and skipping over blank ones or channels with weak signals. This means when you
scan (using the CHANNEL +/– buttons) you will receive only clear, active channels. There are
two tuner modes to choose from, ANALOG or DIGITAL.
è
To choose CABLE or AIR (or SKIP when
you skip Analog Auto Tuner Setup)
AUTO TUNER SETUP
IN ANALOG
TUNER MODE
IN DIGITAL
AIR
π†
To TUNER MODE (IN DIGITAL)
ATSC
TUNER MODE
è
To choose ATSC or Digital Cable (or SKIP
when you skip Digital Auto Tuner Setup)
†
To START
START
SELECT OPERATE
After Analog Auto Tuner Setup is finished, Digital Auto
Tuner Setup starts.
MENU
EXIT
NOW
PROGRAMMING !
Now Programming...
20
48
When the setup is finished, "THANK YOU ! SETUP IS NOW COMPLETE" is displayed. Your
quick setup is now complete. You can now begin watching your television, or you can continue
on in this guide for more information on programming your remote control, or using the
JVC onscreen menu system to customize your television viewing experience.
Notes:
• If you want to cancel the Auto Tuner Setup, press the MENU button.
• Noise muting will not work during Auto Tuner Setup.
• If you choose SKIP, it finished without doing the Auto Tuner Setup.
Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending
on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is
normal.
The Quick Setup is complete
STOP
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
Setting the CATV, VCR and DVD Codes
You can program your remote to operate your cable box, satellite receiver, VCR or DVD
player by using the instructions and codes listed below. If the equipment does not respond
to any of the codes listed below or to the code search function, use the remote control
supplied by the manufacturer.
Cable Box or Satellite Codes
The remote control is programmed with cable box and satellite codes for power on/off,
channel up/down, and 10 key operation.
1) Find the cable box or satellite brand from the list of codes shown below.
2) Slide the 2-way selector switch to “CATV”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the cable box/satellite receiver.
• If your cable or satellite box does not respond to the first code, try the others listed. If it does
not respond to any code, try the search codes function, on page 31.
Cable Box
Codes
024
Digital
Satellite
Systems
Codes
Cable Box
Codes
ABC
Puser
RCA
032
Archer
032, 025
051, 032
022, 051
058, 059
024, 032, 025
029
061, 070
032
Echostar
(Dish Network) 115
100, 113, 114,
Cableview
Citizen
Curtis
Realistic
Regal
058, 064, 040,
041, 042, 045,
068
Express VU
G.E.
100, 113
106
Diamond
Eagle
Regency
034
G.I.
108, 120, 121,
122
Rembrandt
037, 032, 051,
038
Eastern
GC Brand
Gemini
General
034
032, 051
022, 043
065, 024, 025,
Gradiente
Hitachi
112
Samsung
051
104, 111
Scientific Atlanta 057, 058, 059
SLMark
051, 047
051, 056
032, 051
HNS (Hughes)
104
Instrument/Jerrold 026, 027, 020,
021, 022, 057,
023, 072, 074
Sprucer
Stargate
Magnavox
102, 103
Panasonic
Philips
105
Hamlin
040, 041, 042,
045, 058, 064
049, 024
Telecaption
Teleview
Texscan
Tocom
067
102, 103, 116
Hitachi
Macom
047, 051
044
Primestar
108
049, 050, 051,
054
Proscan
RCA
106, 109, 110
106, 109, 110
035, 036, 066,
074
Magnavox
033
Sony
107
030
Memorex
Movietime
Toshiba
Unika
050, 048
032, 025
Star Choice
Toshiba
104, 108
032, 051
039, 037, 048
101, 104, 117,
118, 119
Oak
Universal
Videoway
Viewstar
Zenith
022, 032
052
Panasonic
055, 056, 060,
071, 073
Uniden
102, 103
Paragon
Philips
063
029, 030
063, 046
046
028, 029, 030,
052, 053, 031,
069
Zenith/Drake
Satellite
Pioneer
Pulsar
047, 062
051, 032
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
VCR Codes
The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward,
rewind, pause, record, channel up/down operation.
1) Find the VCR brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the VCR.
• If your VCR does not respond to the first code, try the others listed. If it does not respond to
any of the codes, try the search codes function on page 31.
• After you program your remote, some VCR buttons may not work properly. If so, use the
VCR’s remote.
• To record, hold down the REC button on the remote and press PLAY.
Codes
035
027, 032, 095
Codes
Codes
VCR
Admiral
VCR
VCR
Marantz
Marta
003, 004, 005
064
Samsung
037, 060, 062,
033, 089
Aiwa
Akai
Samtron
Sansui
089
029, 072, 073, Memorex
074
024, 067
003, 026, 020,
052
038, 040, 047,
048, 041, 042
MGA
Audio Dynamic 003, 005
Sanyo
Scott
063, 067, 091,
071
Bell & Howell
Broksonic
Canon
063, 071
020, 026, 094
023, 025
043
Minolta
058, 045, 093
Mitsubishi
038, 040, 047,
048, 041, 042,
078, 090
059, 060, 062,
067, 038, 040,
047, 048, 026,
020
CCE
Multitech
NEC
047, 027, 062
Citizen
064
003, 004, 005,
000
Sears
063, 064, 065,
066, 058
Craig
063, 029, 064
Curtis Mathes
045, 024, 027,
093
Olympic
024, 023
Sharp
035, 036, 080,
088
Optimus
028, 021, 035,
064
Daewoo
043, 059, 024,
092
Shintom
075
026, 020
Orion
DBX
003, 004, 005
Signature 2000 027, 035
Panasonic
023, 024, 021,
022
Dimensia
Emerson
045, 093
Singer
Sony
075
043, 026, 077,
061, 025, 042,
020, 076
Penney
024, 058, 045,
063, 003, 004,
005, 093
028, 029, 030,
053, 054, 055
SV 2000
Sylvania
027
Fisher
Funai
063, 066, 067,
065, 071, 091
Pentax
Philco
058, 005, 045,
093
031, 023, 024,
027
027, 026, 020,
000
031, 024, 027,
023, 026, 020,
043
Symphonic
Tashiro
Tatung
027, 081
064
033, 045, 024
G.E.
003, 004, 005
Philips
031, 023, 024,
086
Go Video
037, 051, 049,
050, 089
Teac
003, 004, 027,
005
Pioneer
Proscan
023
Goldstar
064
Technics
Teknika
021, 022, 023,
024
045, 058, 023,
024, 031, 046,
059, 060, 093,
033, 087
Gradiente
083, 084, 081,
000, 001
024, 027, 070
Hitachi
023, 045, 058,
093, 027, 081
Thomson
Toshiba
033, 096
Quasar
021, 022, 023,
024
Instant Replay 024, 023
059, 046, 079
Radio Shack
033, 024, 063,
036, 067, 040,
027
Jensen
JVC
003
Vector Research 005
003, 004, 005,
000, 001, 002,
006, 007
Wards
Yamaha
Zenith
035, 036, 067,
044, 064
033, 045, 058,
023, 024, 031,
046, 059, 060,
083, 084, 085,
087, 093, 096
RCA
063, 003, 004,
005
Kenwood
003, 004, 064,
005
044, 082, 064,
094
LG
064
Realistic
024, 063, 036,
067, 040, 027
LXI
027, 064, 058,
065, 066, 063,
067
Magnavox
031, 023, 024,
086
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
DVD Codes
The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward,
rewind, previous/next chapter, tray open/close, and still/pause operation.
1) Find the DVD player brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.
3) Press and hold down the DISPLAY button, then enter the first code number listed with the 10
key pad.
4) Release the DISPLAY button, and confirm the operation of the DVD player.
• If your DVD player does not respond to the first code, try the others listed. If it does not
respond to any of the codes, try the search codes function on page 31.
• After you program your remote, some DVD buttons may not work properly. If so, use the
DVD player’s remote.
DVD Player
Aiwa
Codes
DVD Player
Mintek
Codes
057
DVD Player
Sharp
Codes
028
043
Apex
040, 054,
055
Mitsubishi
025
Silvania
038
Bose
058
Next Base
Onkyo
056
SMC
Sony
048
024, 045,
046, 047
Denon
020, 037
041, 052
Funai
038
032
053
Oritron
044
Technics
Thomson
Toshiba
020
021
023
Go–Video
Panasonic
Philips
020
Harman
Kardon
023, 036
Hitachi
JVC
031
Pioneer
Polk Audio
Raite
022
036
033
Venturer
Vialta
051
050
000
Kenwood
035, 020
Wave
042
Yamaha
Zenith
020, 049
027, 032
KLH
051
039
050
RCA
021, 026
034
Konka
Koss
Sampo
Samsung
030
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Programming
Search Codes
Cable/Satellite Search Codes Function
1) Slide the first 2-Way Mode Selector switch to CATV.
2) Press the POWER and RETURN+/TV buttons. Hold for at least three seconds and release.
3) Press the POWER button on the remote, and see if the cable or satellite box responds.
4) If there was a response, press RETURN+/TV. The codes are now set. If there was no
response, repeat Step 3. If you repeat Step 3 a total of 80 times without a response, use
the remote control that came with your equipment.
5) Press RETURN+/TV to exit.
VCR/DVD Search Codes Function
1) Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR” or
“DVD”.
2) Press the VCR or DVD POWER and RETURN+/TV buttons. Hold for at least three seconds
and release.
3) Press the VCR or DVD POWER button, and see if the VCR or DVD responds.
4) If there was a response, press RETURN+/TV. The codes are now set. If there was no
response, repeat Step 3. If you repeat Step 3 a total of 80 times for the VCR (40 times for
the DVD player), and there is no response, use the remote control that came with your
equipment.
5) Press RETURN+/TV to exit.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Using the Guide
Certain symbols are used throughout this guide to help you learn about the features of your
new television. The ones you will see most frequently are:
π† Up and Down arrows mean press the CH+ or CH– buttons. Pressing the CH+ or CH–
buttons let you:
• Move vertically in a main menu screen
• Move through a submenu screen
• Move to the next letter, number, or other choice in a submenu
• Back up to correct an error
• Scan through TV channels (when not in a menu screen)
è Left and right arrows mean press the VOLUME+ or VOLUME- buttons to move left or right
to:
• Select a highlighted menu item
• Select an item in a submenu
• Select numbers in certain menu options
• Turn the volume up or down (when not in a menu screen)
The “press button” icon means you should press the button named on your remote
control. (Button names appear in SMALL CAPITAL LETTERS.)
The “helping arrow” icon points to the highlighted or selected item in a menu.
To bring up the onscreen menu, press the MENU button on the remote control. The item that
appears in green is the one currently selected. If you use the Menu button on the TV’s side
panel instead of the remote, an additional menu screen showing VIDEO STATUS and ASPECT
will appear between INITIAL SETUP and PICTURE ADJUST. The “interactive plug-in menu” will
appear the first time the TV is plugged in.
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
SET LOCK CODE
OFF
AUTO DEMO
NEXT PAGE
(4/5)
MENU
SELECT OPERATE
EXIT
Note:
• Menus shown in this book are illustrations, not exact replications of the television’s onscreen
displays.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
The Onscreen Menu System
Your television comes with JVC’s onscreen menu system. The onscreen menus let you make
adjustments to your television’s operation simply and quickly. Examples of the onscreen
menus are shown on the next page. Detailed explanations on using each menu follow later in
this guide. For information about the interactive plug-in Menu, see pages 25 - 27.
The Onscreen Menu System
To open the onscreen menu system, press the MENU button on the remote control. You
navigate within the onscreen menus by using the four directional arrow buttons on the remote
control. (These buttons are also the CH +/– and VOL +/– buttons. Channel and volume functions
will not operate when the onscreen menu is active).
The selected feature and option on a menu screen are highlighted in a different color.
Selected Option
(Green)
ENG. FRAN. ESP.
LANGUAGE
Selected Option
(Blue)
CLOSED CAPTION
To move to a different feature use the π† arrows to move up or down the list. When you
press the up arrow at the top of the list or the down arrow at the bottom, the next menu screen
will appear. Use the arrows √ ® to select an option from the highlighted feature. Pressing
MENU on the remote control will close the onscreen menu system and return you to normal
television viewing.
Each menu and its features will be discussed in the following pages of this guide.
Notes:
• If you do not press any buttons for a few seconds, the onscreen menu will automatically
shut off.
• Button names in this guide are shown in SMALL CAPITAL LETTERS.
• Menus may appear in different sizes onscreen depending on the aspect ratio selected.
• Some menu items may not appear in menu screens when certain aspect ratios or inputs
are selected.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Menus
Press the MENU button
TO INITIAL SETUP 03
INITIAL SETUP
/
INITIAL SETUP
CLOCK TIMERS
PREVIOUS
SET CLOCK
PREVIOUS
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
OFF
SIZE1
VIDEO-1 MONITOR OUT
DIGITAL-IN
/
ON OFF TIMER
DIGITAL
DIGITAL-IN AUDIO
SET LOCK CODE
AUTO DEMO
OFF
NEXT PAGE
(4/5)
NEXT PAGE
NEXT PAGE
(1/5)
MENU
MENU
MENU
SELECT OPERATE
EXIT
SELECT OPERATE
EXIT
SELECT OPERATE
EXIT
CLOCK/TIMERS
INITIAL SETUP 01
INITIAL SETUP 04
INITIAL SETUP
INITIAL SETUP
SOUND ADJUST
PREVIOUS
PREVIOUS
PREVIOUS
DIGITAL SETUP
NOISE MUTING
ON
OFF
ON
BASS
00
00
00
FRONT PANEL LOCK
V1 SMART INPUT
TREBLE
BALANCE
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
LOW
(2/5)
RESET
NEXT PAGE
(5/5)
NEXT PAGE
NEXT PAGE
MENU
SELECT OPERATE
EXIT
MENU
MENU
SELECT OPERATE
EXIT
SELECT OPERATE
EXIT
INITIAL SETUP 05
SOUND ADJUST
INITIAL SETUP 02
INITIAL SETUP
PICTURE ADJUST
PICTURE ADJUST
PREVIOUS
PREVIOUS
STANDARD
PREVIOUS
STANDARD
ILLUMINATION
LANGUAGE
LOW
COLOR TEMPERATURE
DIG. NOISE CLEAR
COLOR MANAGEMENT
DYNAMIC GAMMA
SMART PICTURE
RESET
HIGH
OFF
OFF
OFF
ON
TINT
00
00
00
00
00
ENG. FRAN. ESP.
COLOR
PICTURE
BRIGHT
DETAIL
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
OFF
ON
ENERGY SAVER MODE
NEXT PAGE
(1/2)
EXIT
NEXT PAGE
(2/2)
NEXT PAGE
(3/5)
MENU
MENU
SELECT OPERATE
SELECT OPERATE
EXIT
MENU
SELECT OPERATE
EXIT
PICTURE ADJUST 02
INITIAL SETUP 03
PICTURE ADJUST 01
TO INITIAL SETUP 04
Notes:
• The DIGITAL-IN menu can only be displayed when a 480p picture signal is input to the
digital-in terminal and the picture is being displayed on the screen.
• When the Menu button on the TV side panel is pressed, the FRONT PANEL CONTROL menu
between INITIAL SETUP 05 and PICTURE ADJUST 01 will appear.
• Regarding the digital setup menu, see page 70.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Auto Tuner Setup
The auto tuner setup function is described on page 27 as the interactive plug-in menu. If you
need to run the auto tuner setup again, follow the steps below.
Press the MENU button
AUTO TUNER SETUP
IN ANALOG
π†
è
π†
è
π†
è
To AUTO TUNER SETUP
TUNER MODE
IN DIGITAL
AIR
To operate
ATSC
TUNER MODE
To TUNER MODE (IN ANALOG)
To choose CABLE, AIR or SKIP
To TUNER MODE (IN DIGITAL)
To choose ATSC, DIGITAL CABLE or SKIP
PRESS OK TO START
SELECT OPERATE
MENU
EXIT
Press the OK button to start
Programming will take approximately 2 to 4 minutes. The auto tuner is finished when the
message PROGRAMMING OVER! appears onscreen.
Press the Menu button when finished
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Channel Summary
Channel summary allows you to customize the line-up of channels received by your TV.
Regarding analog channels, you can add or delete channels from the line-up or prevent any
unauthorized viewers from watching any or all 191 channels. Regarding digital channels, the
only channels that will appear are the ones that are broadcasting.
Press the MENU button
To CHANNEL SUMMARY
To operate
Analog Channels
CHANNEL SUMMARY
π†
CHNO. SCAN
ID
CHNO. SCAN
ID
è
01
06
HBO
The Channel summary screen will now be displayed with
the channels set to scan marked with an “√”. Regarding
analog channels, you can delete channels from the scan
by removing the “√”. If any channels were missed during
auto tuner setup and you wish to add them, you may by
placing an “√” next to the channel number.
02
03
04
05
MTV
07
08
09
10
L
A&E
E!
OK
MENU
SELECT
OPERATE
EXIT
Digital Channels
• Digital channels can not be added to the channel
summary if the auto tuner setup did not find them.
Channel Summary Digital
CH No.
D01
Scan
Station Name
FOX
π†√® To the SCAN column
Press the OK button to include or delete from
scan
D02
ABC
D02
CNN
D10-1
D10-2
D12345
NBC
BOX
Press the MENU button when finished
NHK
BACK
MENU
Operate
Back
Exit
Note:
Note:
• The number of a digital channel may change,
depending on the time of some broadcastings. If
this channel existed and now had disappeared, the
lock channel or scanned channel by the channel
summary for that channel will be cancelled.
• When the Cable Card is not
inserted into the Cable Card
Slot:
If you are watching analog
channels, the above screen
appears.
If you are watching digital
channels, the below screen
appears.
• When the Cable Card is
inserted into the Cable Card
Slot:
Below screen appears
Both analog and digital
channels are listed, but the
background video is not
displayed.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
How to set the channel label. (This is only for analog broadcasting.)
Press the MENU button
ID
π†
è
π†
To CHANNEL SUMMARY
To operate
To the ID column
CHANNEL 09
RESET
Press the OK button to enter
OK
PRESS TO FINISH
è
π†
To select the character you want
To move to the next space
MENU
SELECT OPERATE
EXIT
...continue to follow these directions for all four
spaces
Press the OK button to finish
Your characters are now set
Press the MENU button when finished
If you want to reset the characters you set:
Press the MENU button
π†
è
π†
To CHANNEL SUMMARY
To operate
To the ID column
Press the OK button to enter
To select RESET
π†
Press the OK button to finish
Your characters are now reset
Notes:
• You can use characters for: Alphabet, numbers, marks and spaces.
• It is possible to set the maximum of 40 channel labels.
• If you try to set more than the 40 maximum, the message "MEMORY OVERFLOW" will
appear.
You can block access to a channel by activating the channel lock.
Press the MENU button
π†
To CHANNEL SUMMARY
To operate
è
π†√® To the Lock Column (
)
Press the ZERO button to lock or unlock that channel
Press the MENU button when finished
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Channel Guard Message
When a viewer attempts to watch a guarded channel, the following message appears:
To watch a channel that you have locked, enter the
THIS CHANNEL IS LOCKED BY
CHANNEL GUARD.
Lock Code using the 10 key pad.
If the wrong code is entered, the message
“INVALID LOCK CODE!” will flash on the screen.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
The channel cannot be accessed until the correct code
is entered.
NO. - - - -
Notes:
• Once a channel has been unlocked, it will remain unlocked until the television is turned off.
• See also “Set Lock Code”, page 44.
V-Chip
Your TV is equipped with V-Chip technology which enables you to block channels or content
that you feel to be inappropriate for children, based on US and Canada rating guidelines.
V-Chip has no effect on video signals from a DVD discs, VCR tapes or Camcorder connection.
Note: Some programs, and movies are broadcast without a ratings signal. Even if you set
up V-CHIP ratings limits, these programs will not be blocked. See page 39 for information on
how to block unrated programs.
Note (for Canadian viewers): The V-Chip function is based on specifications designed for
the United States and therefore may not work properly in Canada.
You can customize the V-Chip settings of your television to match your personal tastes. The
V-Chip menu below is the starting point for your V-Chip settings
You can use US V-Chip settings (for programming broadcast from the United States), Canadian
V-Chip settings (for programming broadcast from Canada), and movie ratings. You may use
any or all of the settings (US V-Chip, Canada V-Chip, Movie ratings). Descriptions for setting
each of the three V-Chip formats appear in the next six pages along with descriptions of the
rating categories.
To access the rating categories:
Press the MENU button
V-CHIP
V-CHIP
OFF
π†
è
To V-CHIP
To operate (Lock icon
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
will appear)
Press ZERO to access the V-Chip menu
VIEW
è
To turn V-Chip ON or OFF (V-Chip must be
turned ON for rating settings to operate)
π†
To move to SET US TV RATINGS,
SET MOVIE RATINGS, or
MENU
SELECT OPERATE
EXIT
SET CANADIAN RATINGS (see following
pages for descriptions of each item)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Unrated Programs
Unrated programming refers to any programming which does not contain a rating signal.
Programming on television stations which do not broadcast rating signals will be placed in the
“Unrated Programming” category.
Examples of Unrated programs:
• Emergency Bulletins
• News
• Public Service Announcements
• Sports
• Locally Originated Programming
• Political Programs
• Religious Programs
• Weather
• Some Commercials
Note:
• TV programs or movies that do not have rating signals will be blocked if the unrated category
is set to BLOCK.
Directions to Block Unrated Programs
You can block programs that are not rated.
Press the MENU button
V-CHIP
OFF
V-CHIP
π†
To V-CHIP
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
è
To operate (The lock icon
appears)
Press ZERO to access V-Chip setup options
VIEW
π†
To UNRATED
è
To VIEW or BLOCK
MENU
SELECT OPERATE
EXIT
Press MENU when done
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
US V-Chip Ratings
U.S. PARENTAL RATING SYSTEMS
Programs with the following ratings are appropriate for children.
❒ TV Y is Appropriate for All Children
Programs are created for very young viewers and should be suitable for all ages, including
children ages 2 - 6.
❒ TV Y7 is for Older Children
Most parents would find such programs suitable for children 7 and above. These programs
may contain some mild fantasy violence or comedic violence, which children should be able
to discern from reality.
Programs with the following ratings are designed for the entire audience.
❒ TV G stands for General Audience
Most parents would find these programs suitable for all age groups. They contain little or no
violence, no strong language, and little or no sexual dialog or situations.
❒ TV PG Parental Guidance Suggested
May contain some, but not much, strong language, limited violence, and some suggestive
sexual dialog or situations. It is recommended that parents watch these programs first, or
with their children.
❒ TV 14 Parents Strongly Cautioned
Programs contain some material that may be unsuitable for children under the age of 14
including possible intense violence, sexual situations, strong coarse language, or intensely
suggestive dialog. Parents are cautioned against unattended viewing by children under 14.
❒ TV MA Mature Audiences Only
These programs are specifically for adults and may be unsuitable for anyone under 17
years of age. TV MA programs may have extensive V, S, L, or D.
Viewing Guidelines
In addition to the ratings categories explained above, information on specific kinds of content
are also supplied with the V-Chip rating. These types of content may also be blocked. The
content types are:
• V/FV is for VIOLENCE/FANTASY VIOLENCE
• S stands for SEXUAL CONTENT
• L stands for strong LANGUAGE
• D stands for suggestive DIALOG
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Setting US V-Chip Ratings
Press the MENU button
V-CHIP
V-CHIP
OFF
π†
è
To V-CHIP
To operate (lock icon
SET US TV RATINGS
SET MOVIE RATINGS
SET CANADIAN RATINGS ENG
SET CANADIAN RATINGS FRE
UNRATED
appears)
Press ZERO to access the V-Chip menu
VIEW
è
π†
è
To turn V-Chip ON or OFF
To move to SET US TV RATINGS
To operate
MENU
SELECT OPERATE
EXIT
Directions to set US V-Chip Ratings
Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and
press the π† or √® to move the cursor to the correct location. Press OK to turn the locking
feature on or off. An item is locked if the
icon appears instead of a “—”.
For example. To block viewing of all TV 14 shows, move the cursor to the top row of that
column and add a lock icon. Once you’ve put a lock on the top row, everything in that column
is automatically locked.
SET US TV RATINGS
π†√® To the TV 14 Column
TV TV
MA 14
TV
PG
TV
G
TV
Y7
TV
Y
Press the OK button to lock
Press the MENU button when finished
V/FV
S
L
Note:
D
• If you want to change the setup, move the cursor to
the top column and change the lock icon to “—” by
pressing OK again. You may then select individual
categories to block.
OK
MENU
EXIT
SELECT
OPERATE
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Movies Ratings
❒ NR – Not Rated
This is a film which has no rating. In many cases these films were imported from countries
which do not use the MPAA ratings system. Other NR films may be from amateur producers
who didn’t intend to have their film widely released.
NR (Not Rated) Programming may contain all types of programming including children’s
programming, foreign programs, or adult material.
❒ G – General Audience
In the opinion of the review board, these films contain nothing in the way of sexual content,
violence, or language that would be unsuitable for audiences of any age.
❒ PG – Parental Guidance
Parental Guidance means the movie may contain some contents such as mild violence,
some brief nudity, and strong language. The contents are not deemed intense.
❒ PG-13 – Parents Strongly Cautioned
Parents with children under 13 are cautioned that the content of movies with this rating may
include more explicit sexual, language, and violence content than movies rated PG.
❒ R – Restricted
These films contain material that is explicit in nature and is not recommended for
unsupervised children under the age of 17.
❒ NC-17 – No One Under 17
These movies contain content which most parents would feel is too adult for their children
to view. Content can consist of strong language, nudity, violence, and suggestive or explicit
subject matter.
❒ X – No One under 18
Inappropriate material for anyone under 18.
Directions to set Movie (MPAA) Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (Lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET MOVIE RATINGS
To enter movies menu
For example:
To block viewing of X and NC-17 rated from shows:
SET MOVIE RATINGS
π†√® To the X Column
Press the OK button to lock
π†√® To the NC-17 Column
Press the OK button to lock
Press the MENU button to finish
N
P
G13
X
C17
R
PG
G
NR
OK
MENU
EXIT
SELECT
OPERATE
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Canadian V-Chip Ratings
❒ E – Exempt
Exempt programming includes: news, sports, documentaries and other information
programming, talk shows, music videos, and variety programming.
❒ C – Programming Intended for Children
Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive
behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or
unrealistic in nature.
❒ C8+ – Programming Intended for Children 8 and Over
Violence Guidelines: Any realistic depictions of violence will be infrequent, discreet, of low
intensity and will show the consequences of the acts. There will be no offensive language,
nudity or sexual content.
❒ G – General Audience
Programming will contain little violence and will be sensitive to themes which could affect
younger children.
❒ PG – Parental Guidance
Programming intended for a general audience, but which may not be suitable for younger
children. Parents may consider some content not appropriate for children aged 8-13.
❒ 14+ – 14 Years and Older
Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and
early teens. Programming may contain mature themes and scenes of intense violence.
❒ 18+ – Adult
Material intended for mature audiences only.
Directions to set Canadian V-Chip Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET CANADIAN RATINGS ENG (for English)
To enter ratings menu
For example:
To block viewing of programming rated 14+ and 18+:
SET CANADIAN RATINGS ENG
è
To the 18+ Column
Press the OK button to lock
P
C
8
G
C
18+
14+
G
è
To the 14+ Column
Press the OK button to lock
Press the MENU button to finish
MENU
OK
EXIT
SELECT
OPERATE
Note:
• For instructions on “SET CANADIAN RATINGS FRE (in French)”, please see page 43 in the
French side of this user’s guide.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Set Lock Code
Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes
preset with a lock code of “0000”. You may change the code to any four-digit number you wish.
To change the lock code, follow the steps below.
Press the MENU button
SET LOCK CODE
π†
To SET LOCK CODE
To operate (lock icon
LOCK CODE
0000
è
appears)
Press ZERO to access the lock code
The first digit will be highlighted
OK
PRESS
TO FINISH
MENU
SELECT OPERATE
EXIT
è
π†
To select the number
To move to the next digit
Continue to follow these directions for all four numbers
Press the OK button to finish (your lock code is now set)
Press the Menu button when finished
When a viewer attempts to watch a blocked channel, this message appears:
THIS PROGRAMMING EXCEEDS
YOUR RATING LIMITS.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
NO. - - - -
The channel will remain blocked until the correct lock code is entered (see above for
information on setting your lock code).
Notes:
• After a power interruption you must reset the lock code.
• Write your lock code number down and keep it hidden from potential viewers.
• If you forget the lock code, a new code may be set using the steps listed above.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Auto Demo
This function lets you preview the Dynamic Gamma demo.
Press the MENU button
INITIAL SETUP
PREVIOUS
AUTO TUNER SETUP
CHANNEL SUMMARY
V-CHIP
π†
è
To AUTO DEMO
To turn AUTO DEMO ON or OFF
SET LOCK CODE
Notes:
OFF
AUTO DEMO
• Auto demo starts 2 seconds after it is set to ON.
• To stop auto demo, press the BACK button.
NEXT PAGE
(4/5)
MENU
SELECT OPERATE
EXIT
Illumination
The illumination feature allows you to adjust the brightness of the light on the front of the
television. When you turn the power on the televison, the front panel light remains on when
illumination is set to LOW or HIGH.
Press the Menu button
INITIAL SETUP
PREVIOUS
π†
To ILLUMINATION
ILLUMINATION
LANGUAGE
LOW
è
To choose HIGH, LOW or OFF
ENG. FRAN. ESP.
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
Press the MENU button when finished
OFF
ON
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
Language
The language function is described on page 25 as the interactive plug-in menu. If you need to
choose the language again, follow the steps below.
Press the Menu button
INITIAL SETUP
PREVIOUS
π†
To LANGUAGE
ILLUMINATION
LANGUAGE
LOW
è
To choose a language: ENG. (English), FRAN.
(French) or ESP. (Spanish)
ENG. FRAN. ESP.
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
OFF
ON
Press the MENU button when finished
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Closed Caption
Many broadcasts now include an onscreen display of dialog called closed captions. Some
broadcasts may also include displays of additional information in text form. Your television can
access and display this information using the closed caption feature. To activate the closed
caption feature, follow the steps below. There are three methods. When you are watching
analog channels, you can perform Analog Setting of closed caption. When you are watching
digital channels, you can perform Digital Auto Setting or Digital Manual Setting.
Analog Setting
Press the MENU button
CLOSED CAPTION
π†
è
π†
è
π†
è
To CLOSED CAPTION
To enter
To MODE
To select CAPTION or TEXT in MODE
To CAPTION or TEXT
To select a caption (CC1 to CC4) or text
channel (T1 to T4)
MODE
TEXT
CC1
T1
CAPTION
TEXT
OK
PRESS TO FINISH
MENU
SELECT OPERATE
EXIT
Press the OK button to save
Press the MENU button when finished
Digital Auto Setting
Press the MENU button
Digital Closed Caption
Preview
π†
è
π†
è
To CLOSED CAPTION
To enter
To Type
Closed Caption Sample
Type
AUTO
1
Service
Appearance
To select Auto, Advanced or Basic
Auto: Shows closed caption a priority for
digital channels over analog channels. It is
set automatically.
Cancel
Set
BACK
MENU
Select
Operate
Back
Exit
Advanced: Shows only the digital closed
caption.
Basic: Shows only the analog closed
caption.
Digital Closed Caption
Preview
>
Appearance
Closed Caption Sample
Appearance Mode
Auto
π†
è
π†
è
è
π†
To Service
Font
To select 1, 2, 3, 4, 5 or 6
To Appearance
To enter
To select Auto
To Set
Colors
Opacities
Cancel
Set
BACK
MENU
Select
Operate
Back
Exit
Press the OK button to save
The font/type and color are set automatically.
Press the MENU button when finished
Note:
• If you want to cancel the settings, select cancel.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Digital Manual Setting
Press the MENU button
Digital Closed Caption
Preview
>
Appearance
π†
To CLOSED CAPTION
Closed Caption Sample
è
π†
è
π†
è
π†
è
è
π†
è
π†
è
To enter
To Type
Appearance Mode
Manual
Font
Colors
Opacities
To select Auto, Advanced or Basic
To Service
To select 1, 2, 3, 4, 5 or 6
To Appearance
To enter
To select Manual
To Font
To enter
To select Font Size or Font Style
To select the setting you like
Cancel
Set
BACK
MENU
Select
Operate
Back
Exit
Digital Closed Caption
Preview
>
Appearance
Closed Caption Sample
Font Size
Standard
Auto
Appearance Mo
Font
Font Style
Colors
Font Size: Auto, Standard, Large or Small
Cancel
Set
Opacities
Cancel
Font Style: Auto, Serif Mono, Serif, Sanserif mono,
Sanserif, Casual, Cursive or Small Capital
π†
Set
BACK
MENU
Select
Operate
Back
Exit
To Set
Press the OK button to save
π†
è
π†
è
To Colors
To enter
To select Text, Edge or Background
To select the setting you like
Digital Closed Caption
Preview
>
Appearance
Closed Caption Sample
Text
Appearance Mo
White
White
Black
Edge
Auto, White, Black, Red, Green, Blue,
Yellow, Magenta or Cyan
Font
Background
Cancel
Colors
Opacities
Set
π†
To Set
Cancel
Set
BACK
MENU
Press the OK button to save
Select
Operate
Back
Exit
π†
è
π†
è
To Opacities
To enter
To select Text/Edge or Background
To select Auto, Transparent, Translucent,
Solid or Flashing
All fonts used for digital closed
caption and digital menus are
licensed from Monotype Imaging
Inc.
π†
To Set
Press the OK button to save
Press the MENU button when finished
Notes:
• Closed caption subtitles are usually found on closed caption channel CC1. Some programs
may include additional text information which is usually found on text channel T1. The other
channels are available for future use.
• Closed captioning may not work correctly if the signal being received is weak or if you are
playing a video tape.
• Most broadcasts containing closed captioning will display a notice at the start of the program.
• To select the mode, press the C.C. button. See page 65.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Auto Shut Off
This function automatically shuts off your TV when there is no signal from the channel the
TV is on.
INITIAL SETUP
Press the MENU button
PREVIOUS
ILLUMINATION
LANGUAGE
LOW
π†
è
To AUTO SHUT OFF
To turn ON or OFF
ENG. FRAN. ESP.
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
OFF
ON
Press the MENU button when finished
• If the channel that you have on does not receive a
signal for more than one minute, the blinking text
“NOT RECEIVING A SIGNAL” appears on the screen,
and starts the countdown. If no signal is being
received within 10 minutes, the TV shuts itself off.
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
• When i.LINK is displayed, Auto Shut Off will not work.
XDS ID
XDS ID Display provides a channel’s call letters, the network’s name, and even a program
name. The XDS ID information is provided by the broadcaster.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To XDS ID
To turn ON or OFF
ILLUMINATION
LANGUAGE
LOW
ENG. FRAN. ESP.
CLOSED CAPTION
AUTO SHUT OFF
XDS ID
Press the MENU button when finished
OFF
ON
NEXT PAGE
(3/5)
MENU
SELECT OPERATE
EXIT
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Noise Muting
This feature inserts a blank grey screen over channels which are not broadcasting or are too
weak to be received clearly.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To NOISE MUTING
To turn noise muting ON or OFF
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V1 SMART INPUT
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
Press the MENU button when finished
LOW
NEXT PAGE
(2/5)
Note:
MENU
SELECT OPERATE
EXIT
• Noise muting will not work during auto tuner setup or
when you operate channel summary.
• Noise muting will not work when the digital TV or i.LINK is displayed.
Front Panel Lock
This allows you to lock the keys on the side of the TV, so that a child may not accidentally
change your viewing preferences.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To FRONT PANEL LOCK
To turn ON or OFF
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V1 SMART INPUT
Press the MENU button when finished
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
You can turn off this feature in the following ways:
LOW
(2/5)
NEXT PAGE
• Unplug the power cord, and plug it back in. Do this if
your batteries die, or you lose your remote control.
MENU
SELECT OPERATE
EXIT
• Use the remote control.
• Press the MENU button on the side of the TV for more than 3 seconds. In this case, the OSD
for FRONT PANEL LOCK will appear.
Note:
• To turn ON/OFF the TV, press the power button for more than 3 seconds. This feature will
remain ON.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
V1 Smart Input
This feature is used if you have connected an AV Receiver to your television. By turning this
feature on, your television can automatically detect the signal source from your components
that are connected to your AV Receiver.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
To V1 SMART INPUT
To turn ON or OFF
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V1 SMART INPUT
Press the MENU button when finished
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
LOW
Notes:
NEXT PAGE
(2/5)
• If you do not have an AV Receiver connected to your
television, turn this feature OFF.
MENU
SELECT OPERATE
EXIT
• Some AV Receivers may not work with this function.
Video Input Label
This function is used to label video input connections for the onscreen displays.
Press the MENU button
INITIAL SETUP
PREVIOUS
π†
è
π†
è
To VIDEO INPUT LABEL
To operate
NOISE MUTING
ON
FRONT PANEL LOCK
V1 SMART INPUT
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
OFF
ON
To select the desired video input
LOW
To select the desired preset input label (see
chart below)
NEXT PAGE
(2/5)
MENU
SELECT OPERATE
EXIT
Press the OK button to save
VIDEO INPUT LABEL
Press the MENU button when finished
VCR
VIDEO-1
VIDEO-2
VIDEO-3
DIGITAL-IN
DVD
SAT
STB
Preset
Labels
Select when...
OK
PRESS TO FINISH
You have a VCR connected to the video input
VCR
MENU
SELECT OPERATE
EXIT
You have a DVD connected to the video input
DVD
You have a Digital VCR connected to the video input
You have a Set-top Box connected to the video input
You have a Satellite Receiver connected to the video input
You have an Amplifier connected to the video input
You have a Video Game connected to the video input
You have a Video Camera connected to the video input
You have a Video Disc player connected to the video input
DVHS
STB
SAT
AMP
GAME
CAM
DISC
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Position Adjustment
Position adjustment allows you to adjust the position of the picture on the screen vertically
when the aspect is set to panorama, cinema, or full.
Press the MENU button
π†
è
To POSITION ADJUSTMENT
To enter
π†√® To adjust the position
Press the MENU button to finish
Notes:
OK
MENU
RESET
EXIT
OPERATE
• To reset the adjustment to the center, press the
OK button.
• When the arrow disappears, while you are adjusting the position, the position is at it’s
maximum limit.
• If you select regular size and slim size with aspect or Multi Screen, position adjustment
option is not seen.
• When you change the screen size, perform the position adjustment again.
• Position adjustment allows you to adjust the screen position vertically and horizontally when
the aspect is set PANORAMA ZOOM or CINEMA ZOOM for 1080i and 720p signals.
Power Indicator
Power indicator allows you to adjust the brightness of
INITIAL SETUP
the power indicator
PREVIOUS
NOISE MUTING
ON
OFF
ON
FRONT PANEL LOCK
V1 SMART INPUT
Press the MENU button
VIDEO INPUT LABEL
POSITION ADJUSTMENT
POWER INDICATOR
π† To POWER INDICATOR
è
To adjust POWER INDICATOR LOW, HIGH
or OFF
LOW
NEXT PAGE
(2/5)
MENU
SELECT OPERATE
EXIT
Note:
• If you set a timer on the TV, the power indicator will light even if the TV is on stand by.
Video-1 Monitor Out
This function allows you to set whether the signal, which comes from VIDEO-1 input terminal,
should be output from MONITOR OUT terminal. If you select it from MONITOR OUT, set it to
"ON".
INITIAL SETUP
Press the MENU button
PREVIOUS
OFF
SIZE1
VIDEO-1 MONITOR OUT
DIGITAL-IN
π† To VIDEO-1 MONITOR OUT
è To select ON or OFF
DIGITAL
DIGITAL-IN AUDIO
Press the MENU button to finish
NEXT PAGE
(1/5)
MENU
SELECT OPERATE
EXIT
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup
Digital-In
The DIGITAL-IN option can only be displayed in the INITIAL SETUP menu when a 480p picture
signal is being input to the DIGITAL-IN terminal. This option adjusts the position when a 480p
picture signal is being displayed on the screen. There are two types of 480p picture signals:
640x480 and 720x480. If the displayed picture is slightly shifted, the position can be adjusted
by selecting either SIZE1 or SIZE2.
INITIAL SETUP
Press the MENU button
PREVIOUS
OFF
SIZE1
VIDEO-1MONITOR OUT
DIGITAL-IN
π† To DIGITAL-IN
DIGITAL
DIGITAL-IN AUDIO
è To enter
π† To select AUTO, SIZE1 or SIZE2
Press the MENU button to finish
NEXT PAGE
(1/5)
MENU
SELECT OPERATE
EXIT
Notes:
• The DIGITAL-IN menu can only be displayed when a 480p picture signal is input to the
Digital-In terminal and the picture is being displayed on the screen.
• You can select AUTO only when the signal is 480p for HDMI. When you select AUTO, the
televison will select "SIZE1" or "SIZE2" automatically.
Digital-In Audio
This feature is used if you have a DTV or HDMI
compatible component connected to your TV.
INITIAL SETUP
PREVIOUS
OFF
VIDEO-1MONITOR OUT
DIGITAL-IN
Press the MENU button
SIZE1
DIGITAL
DIGITAL-IN AUDIO
π†
To DIGITAL-IN AUDIO
è
To select “ANALOG”, “DIGITAL” or "AUTO"
Press the Menu button when finished
NEXT PAGE
(1/5)
MENU
SELECT OPERATE
EXIT
Notes:
• If your DTV or HDMI component is capable of digital audio and video, choose DIGITAL. If
your DTV or HDMI component is capable of analog audio and digital video, choose ANALOG.
• Refer to your DTV or HDMI component’s instruction manual for more information.
• When you select DIGITAL, select PCM on Digital Sound in the Digital Setup menu. See page
71.
• When you select AUTO, the television will select "ANALOG" or "DIGITAL" automatically,
depending on the audio input from the HDMI.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjust
Picture Settings
These settings allow you to change and adjust the way the picture appears on your television.
TINT
Tint allows you to adjust the levels of red and green in your TV picture.
COLOR
The color function lets you make all the colors in the TV picture appear either more vivid or
subtle.
PICTURE
Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker
or brighter picture overall.
BRIGHT
You can adjust the overall brightness of the TV picture with the Bright control.
DETAIL
The Detail feature adjusts the level of fine detail displayed in the picture.
ENERGY SAVER MODE
The energy saver mode adjusts the level of brightness on the TV screen.
Adjust the Picture Settings
Press the MENU button
PICTURE ADJUST
π†
To TINT, COLOR, PICTURE, BRIGHT, DETAIL
or ENERGY SAVER MODE
To enter
PREVIOUS
TINT
STANDARD
00
00
00
00
00
COLOR
PICTURE
BRIGHT
DETAIL
√ ®
+02
TINT
ENERGY SAVER MODE
NEXT PAGE
(1/2)
EXIT
√ ®
π†
To adjust the setting
To move to the next setting
MENU
SELECT OPERATE
Press the MENU button when finished
Color Temperature
You can decide how strong or dull the colors appear on the TV screen.
Press the MENU button
PICTURE ADJUST
PREVIOUS
STANDARD
π†
è
To COLOR TEMPERATURE
To enter
COLOR TEMPERATURE
DIG. NOISE CLEAR
COLOR MANAGEMENT
DYNAMIC GAMMA
SMART PICTURE
RESET
HIGH
OFF
OFF
OFF
ON
COLOR TEMPERATURE LOW HIGH
è
To set LOW or HIGH
Press the MENU button when finished
NEXT PAGE
(2/2)
MENU
SELECT OPERATE
EXIT
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjust
Digital Noise Clear
With digital noise clear, this helps take our static or noise from a channel that may not be
coming in clearly.
Press the MENU button
DIG. NOISE CLEAR
OFF
LOW
HIGH
π†
è
π†
To DIG. NOISE CLEAR
To enter
To select the mode “LOW”, “HIGH” or “OFF”
Press the MENU button when finished
Color Management
This TV supports the COLOR MANAGEMENT function to ensure dull colors are compensated
to produce natural hues.
Press the MENU button
COLOR MANAGEMENT
ON
π†
è
π†
To COLOR MANAGEMENT
To enter
To select the mode “ON" or "OFF"
OFF
Press the MENU button when finished
Dynamic Gamma
JVC's Dynamic Gamma Circuitry (DGC makes it easier to see dark areas when a picture has
many dark areas, and makes it easier to see the bright areas when a picture has many bright
areas. DGC is turned on, DGC analyzes and adjusts the total level of picture brightness
balance, especially in dark areas where the level of greyscale is often lost, turning completely
to black DGC automatically enhances the detail in these dark areas providing a more dynamic
image with finer detail, so the optimum picture settings are automatically set for each picture.
Normally use with DGC on.
Press the MENU button
DYNAMIC GAMMA
ON
π†
è
π†
To DYNAMIC GAMMA
To enter
To turn ON or OFF
OFF
Press the MENU button when finished
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjust
Smart Picture
Smart Picture detects the APL (Average Picture Level) and adjusts the contrast suitable for
what you are watching.
Press the MENU button
SMART PICTURE
ON
π†
è
π†
To SMART PICTURE
To enter
To select the mode "ON" or "OFF"
Press the MENU button when finished
OFF
Note:
• When you have "DYNAMIC" selected in the "VIDEO STATUS", Smart Picture is not selected.
Reset
Reset resets all picture adjustments (tint, color, picture, bright, detail, energy saver mode, color
temperature, dig. noise clear, color management and dynamic gamma and smart picture) at
once to the default settings.
Press the MENU button
PICTURE ADJUST
PREVIOUS
STANDARD
π†
è
To RESET
To enter
COLOR TEMPERATURE
DIG. NOISE CLEAR
COLOR MANAGEMENT
DYNAMIC GAMMA
SMART PICTURE
RESET
HIGH
OFF
OFF
OFF
ON
The onscreen menu disappears for a moment,
and then the settings are reset to the default
setting for all the picture adjustments.
NEXT PAGE
(2/2)
Press the MENU button when finished
MENU
SELECT OPERATE
EXIT
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Adjust
Sound Settings
These settings allow you to change and adjust the sound on your television.
BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with
the bass adjustment.
TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio.
BALANCE – Adjust the level of sound between the TV’s left and right speakers with the
balance setting.
Adjust the Sound Settings
Press the MENU button
SOUND ADJUST
PREVIOUS
π†
√ ®
π†
To BASS, TREBLE or BALANCE
To adjust the setting
To move to the next setting
BASS
00
00
00
TREBLE
BALANCE
Press the MENU button when finished
RESET
NEXT PAGE
MENU
SELECT OPERATE
EXIT
Note:
• You can reset the sound adjustments (BASS, TREBLE and BALANCE) you set at once as
the default setting when you select reset. See page 55.
• You can adjust BALANCE only when A.H.S. is off. See page 62.
Reset
Reset resets all Sound Adjustments (Bass, Treble and Balance) at once to the default settings.
See page 55 on how to use reset.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock/Timers
Set Clock
The set clock function is described on page 26 as the interactive plug-in menu. You can choose
to set the clock automatically or manually. If you need to set the clock again, follow the steps
below.
Press the MENU button
π†
è
To SET CLOCK
To enter
When you set the clock automatically, choose AUTO by pressing the
√
or
®
arrows.
π†
è
To TIME ZONE
To select your time zone
ATLANTIC
SET CLOCK
EASTERN
CENTRAL
MOUNTAIN
HAWAII
ALASKA
PACIFIC
MODE
AUTO
--: ----
π†
è
To D.S.T. (daylight savings time)
To turn D.S.T. ON or OFF
TIME
TIME ZONE
DATE/YEAR
D.S.T.
ATLANTIC
JAN/01/05
ON
Press OK to finish
OK
PRESS TO FINISH
SELECT OPERATE
Press the MENU button when finished
MENU
EXIT
When you set the clock manually, choose MANUAL by
pressing the or arrows.
√
®
π†
è
π†
è
π†
è
To move to the hours
To set the hours
To move to minutes
To set the minutes
To TIME ZONE
To select your time zone:
SET CLOCK
(Atlantic, Eastern, Central, Mountain, Pacific,
Alaska or Hawaii)
MODE
MANUAL
--: ----
π†
è
π†
è
π†
è
π†
è
To DATE/YEAR
To set the month
To day
To set the day
To year
TIME
TIME ZONE
DATE/YEAR
D.S.T.
ATLANTIC
JAN/01/05
ON
OK
PRESS TO START CLOCK
To set the year
MENU
SELECT OPERATE
EXIT
To D.S.T. (daylight savings time)
To turn D.S.T. ON or OFF
Press OK to start clock
THANK YOU !!
Press the MENU button when finished
Notes:
• D.S.T. can be used when it is set to ON in the SET CLOCK menu.
• Only when the MODE set to AUTO, the Daylight Savings Time feature automatically adjusts
your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00 am on
the first Sunday in April. The clock will move back one hour at 2:00 am on the last Sunday in
October.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock/Timers
On/Off Timer
The on/off timer lets you program your television to turn itself on or off. You can use it as an
alarm to wake up, to help you remember important programs, or as a decoy when you’re not
home.
Press the MENU button
ON/OFF TIMER
7:00 PM
10:00 PM
03
ON TIME
π†
è
è
To ON/OFF TIMER
OFF TIME
CHANNEL
ON VOLUME
MODE
To operate (begins with ON TIME)
CURRENT
EVERYDAY
NO
To set the hour (AM/PM) you want the TV to
turn on
ON/OFF TIMER
†
è
†
To move to minutes
To set the minutes
OK
PRESS TO FINISH
MENU
SELECT OPERATE
EXIT
To accept ON TIME and move to OFF TIME (the time the TV will turn off). Set the
OFF TIME the same way as ON TIME
†
è
†
To accept OFF TIME and move to CHANNEL
To select channel
To ON VOLUME
è
†
To set the volume level
To move to MODE
è
Choose ONCE or EVERYDAY
†
To ON/OFF TIMER
è
Choose YES to accept the timer setting, choose NO if you don’t wish to accept
Press the OK button to finish
Press the MENU button to exit the menu
Notes:
• The on/off time cannot be set to locked or guarded channels.
• In order for the on/off timer to work, the clock must be set.
• After a power interruption, the timer settings must be reset.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Multi Screen Function
Your television has two kinds of screen: TWIN (2 channels) and INDEX (12 channels).
Note: After you press any multiscreen button, if you press the menu button, only the picture
adjust screen will appear.
Index
This allows you to quickly look at up to 12 channels at a time so that you can decide which one
to watch.
1
5
9
2
3
4
6
7
8
10
11
12
Notes:
• Only RF input signal will be displayed.
• You can watch the channel added in channel summary. See page 36.
Twin
Activate the split-screen option by pressing Twin on
the remote control. The channel (or input) you were
watching before pressing Twin will appear on the left,
07
V-1
the new channel will appear on the right. The sound
will continue to come from the main screen channel
MAIN SCREEN
PICTURE
SPLIT SCREEN
PICTURE
(or input). To turn split-screen off and return to
normal television viewing, press TWIN again or press
the BACK button.
Notes:
• If the signal that you are watching is coming from the HDMI input, you cannot enter the
SWAP or INDEX mode.
• Main Screen and Split Screen will not display the same channel or input at the same time.
• You can enter the TWIN mode when the screen is in NORMAL or INDEX mode.
• Split-screen functions will not work with locked channels or channels blocked by V-Chip
ratings limits. A grey screen will display instead.
• With split screen, the picture from the component terminal and DIGITAL-IN terminal will
not be displayed.
• The aspect of MAIN CHANNEL PICTURE becomes 16:9 when you input the picture of
480p, 720p and 1080i from the component terminal and DIGITAL-IN terminal.
• After you press the Select button, and select SPLIT SCREEN when you press the
OK button, select normal screen. If you don’t operate, the MAIN CHANNEL SCREEN will
be automatically selected about 8 seconds later.
• Aspect does not work in Twin mode.
• When you press the Menu button in Twin mode, it appears only as Picture Adjust menu.
• When the cable card is inserted into the TV, the combination of analog broadcasting and
digital broadcasting will not appear in the TWIN mode.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Freeze
Pressing the FREEZE button causes the screen to change to the split-screen display with the still
picture displayed on the right. In order to return to the normal display, press the FREEZE button
once again.
Note: When the screen is in freeze mode, if you do not operate it within 15 minutes, this
function will cancel out.
Swap
You can exchange the channel (or input) displayed in the split screen window for the main
screen image by pressing the SWAP button.
Note:
• It will only work in TWIN mode.
Select
With SELECT, you can select the picture (channel) while viewing SPLIT screen. When you
press SELECT button, the channel number on the top will be highlighted. Each press of SELECT
will shift the channel.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Power
Turns the TV on or off.
Press the POWER button
Note:
• When you press the power button on the TV, and you are tuned to a digital channel or i.Link,
"NOW WARMING UP... PLEASE WAIT" appears on the screen. It takes a little while to warm
up.
Number Buttons - 10Key Pad
Use the number buttons on the remote control to move directly to a specific channel. For
example, to move to channel 12:
0 (Zero)
1 (One)
2 (Two)
Tune
Lets you decide the input channel and select it. After you press the number buttons on the
remote, press the TUNE button. For example, to move to channel 12:
1 (One)
2 (Two)
Press the TUNE button
Input
Selects the signal input source for the television: VIDEO-1, 2, 3, DIGITAL-IN or i.LINK for
video devices like VCRs, DVD players or camcorders.
Press the INPUT button
By every press of the INPUT button, you can change the input mode.
Notes:
• When you return to TV mode, press the RETURN +/TV button or direct 10 key pad or CHANNEL
+/– button.
• You can also access by pressing the INPUT button on the side of the TV instead of the remote
control.
• i.LINK can be selected only when you have an i.LINK device connected.
TheaterPro D6500K
The TheaterPro D6500K color temperature technology function makes sure that the video you
watch is set to the standard color temperature, so that what you see is as true to what the film
to video editors intended it to be.
Press the THEATERPRO button
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Return +/TV
The RETURN+/TV button has three functions:
Return - Returns to the channel viewed just before the channel currently onscreen.
Return+ - Lets you program a specific channel to return to while scanning through the
channels using the CH+ and CH– buttons.
TV - Returns to the TV mode.
Press the RETURN+/TV and hold for three seconds
RETURN CHANNEL
PROGRAMMED!
The channel currently active has been programmed as your return+ channel. Now scan
through the channels using the CHANNEL+/– buttons.
Press the RETURN+/TV
You will return to your programmed channel.
• To cancel your return+ channel, press and hold the RETURN+ button for three seconds. The
message “RETURN CHANNEL CANCELLED!” will appear.
• Return+ works only with the Channel+/– buttons. Pressing any number key will cancel
return+.
Sound
By pressing the SOUND button, you can change the A.H.S. (Advanced Hyper Surround) mode,
BBE, SMART SOUND and A.H.B (Active Hyper Bass) on or off.
A.H.S. - Adds a more spacious surround sound. Music gives basic effect and movie for more
effect.
BBE - BBE High Definition Sound restores clarity and presence for better speech intelligibility
and musical realism.
SMART SOUND - Decreases high sound levels, giving a regulated sound level.
A.H.B. - You can reinforce the bass sound to maintain rich, full bass at low volumes, and enjoy
a clear sound with boosted bass.
SOUND EFFECT
Press the SOUND button
A.H.S.
MOVIE MUSIC OFF
ON OFF
BBE
π†
To select A.H.S., BBE, SMART SOUND or
A.H.B.
SMART SOUND
A.H.B.
ON OFF
ON OFF
MENU
OPERATE
EXIT
SELECT
è
To choose the setting
Press the MENU when finished
Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under
USP4638258, 5510752 and 5736897. BBE and BBE symbol are registered trademarks of
BBE Sound, Inc.
Note: Smart Sound may become an unnatural effect, depending on the signal source.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Muting
The MUTING button instantly turns the volume down completely when you press it. Press
MUTING and the volume level will instantly go to zero. To restore the volume to its previous
level, press MUTING again.
Video Status
The VIDEO STATUS button gives you a choice of four TV picture display settings, including a
display of your own preferences.
Standard - Resets the picture display to the factory settings.
VIDEO STATUS
Dynamic - Gives a vivid picture with better contrast when viewing in
STANDARD
a brightly lit room.
DYNAMIC
Theater - Gives a rich, film-like look to video when viewing in a
THEATER
dimly lit room.
GAME
Game - Used for when you are playing video games connected to
your TV.
Press the VIDEO STATUS button
By every press of the VIDEO STATUS button, you change the mode.
Note:
• You can also change the mode by pressing the π† buttons.
• You can also access the FRONT CONTROL PANEL screen by using the MENU button on
the side of the TV instead of the remote control. It appears between INITIAL SETUP and
PICTURE ADJUST screen, and it has VIDEO STATUS and ASPECT menus. Choose VIDEO
STATUS by pressing MENU
+/- buttons ( OPERATE
†
®
on the side panel and choose a mode by using the CHANNEL
).
√
Natural Cinema
Natural cinema corrects the problem of blurred edges which may occur when viewing a program
originally shot on film (such as motion pictures) or animation. If you notice blurring at the edges
of these programs, press NATURAL CINEMA and set it to AUTO. Natural Cinema helps correct
conversion errors that occur when film, which is shot at 24 frames-per-second, is broadcast at the
television rate of 30 frames-per-second.
Press the NATURAL CINEMA button
NATURAL CINEMA
AUTO
Notes: The natural cinema mode is automatically set to “AUTO” in the
ON
following cases:
OFF
• Turning on or off
• Changing the channel or input mode
• Using multi-screen functions
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Sleep Timer
The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals
of 15 minutes, for a total time of up to 180 minutes.
Press the SLEEP button
0 15 30 45 60 75 90 105 120 135 150 165 180
Sleep Timer Message
20 seconds before the automatic shutoff, this message will appear:
GOOD NIGHT!!
PUSH SLEEP TIMER BUTTON
TO EXTEND
You then have 20 seconds to press the SLEEP button to
delay the shut off for another 15 minutes.
ML/MTS
MTS technology allows several audio signals to be broadcast in analog at once, giving you a
choice in what you wish to hear with a TV program. In addition to mono or stereo sound, an
MTS broadcast may also include a second audio program (SAP).
Press the ML/MTS button
MTS
By every press of the ML/MTS button, you change
the mode
ON AIR
STEREO
ON AIR
SAP
MONO
Notes:
• When you are receiving a digital broadcast, if there are other languages, you can change the
language by pressing the ML/MTS button.
• Keep the TV in stereo mode to get the best sound quality. The sound will work in stereo
mode even if a certain broadcast is in mono sound only.
• Choose the mono setting to reduce excessive noise on a certain channel or broadcast.
• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.
• MTS unavailable if your television’s Input source is in input 1, 2, 3 or 4 mode, as described
on page 61.
• ML/MTS will not work when you are using the Digital-In.
• You can also change the mode by pressing the π† buttons.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Display
The display screen shows the current status of timers, inputs and XDS ID.
Press the DISPLAY button
The screen to the right shows the following
information:
05 KLVX PBS
JAZZ FESTIVAL
• The current channel or AV input (Channel 05)
NOW
12:20 PM
OFF
• The current time (12:20 pm)
• Sleep timer status/minutes remaining (The Sleep
Timer is off)
SLEEP TIMER
ON/OFF TIMER
EVERYDAY
7:00 PM
ON TIME
• On/off timer status (Set to turn on everyday at 7:
OFF TIME
10:00 PM
00 PM, off at 10:00 PM)
• Each Press of the DISPLAY button changes the
display mode:
Display
Time
Channel
Off
Display - Full screen shown above
Time - Shows the current time only
Channel - Shows the current channel
Off - Turns display off
Notes:
• You may also turn off the display at any step by pressing MENU.
• If the clock, sleep timer or on/off timer are not set, the display screen will show:
“CLOCK NOT SET”, “SLEEP TIMER OFF”, and “ON/OFF TIMER OFF” respectively.
C.C. (Closed Caption)
Use the C.C. (Closed Caption) button to select the mode of closed caption.
Press the C.C. button
CLOSED CAPTION
Notes:
OFF
SMART CAPTION
ON
• SMART CAPTION will appear when you press the MUTING button,
only on channels where the broadcast contains closed captioning.
• When you select ON, it will be the mode selected in the Closed
Caption Menu.
• See page 46 when you set the caption/text mode.
• You can also change the mode by pressing the π† buttons.
Channel +/–
Use these buttons to move up or down all the available channels your TV is able to receive.
Volume +/–
Use these buttons to raise or lower the TV’s volume level.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Favorite
The Favorite button allows you to select your favorite channels easily. First, you must register
the channels that you like. See how to register below.
Press the FAVORITE button
FAVORITE
The favorite channel list will appear.
PREVIOUS
π†
To select the channel you want to watch
101
102
D103
<
CBS
FOX
PBS2
>
Press the OK button
It will change to the channel you have selected.
D107
8
HBO
ABC
Register the favorite channel
NEXT
Press the channel number you want to register
The channel program will change.
Press the FAVORITE button for three seconds
The channel will be registered in the favorite channel list.
Notes:
• Both analog and digital channels can be registered. The digital channels have a "D" in front
of the channel number.
• The maximum number of channels you can register is 24.
• If you have registered the maximum number of channels, and try to register more channels,
the oldest channel you registered will be deleted.
• Sub channels can not be registered.
• The newest channel you registered will appear at the top of the list.
• Regarding digital channels, see pages 73 - 78.
Delete the favorite channel
Press the FAVORITE button
The favorite channel list will appear.
π†
è
To select the channel you want to delete
To enter
Press the OK button
The channel was deleted.
Press the FAVORITE button when finished
Note:
• Before pressing the FAVORITE button when you are finished, press the √® button again, and
you can return to the deleted channel.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Aspect
This feature will help you adjust the picture you are watching to give you the best possible
picture quality.
Aspect Ratios
PANORAMA - With this ratio a normal
4:3 aspect picture is stretched to fit the
dimensions of the 16:9 aspect screen.
REGULAR - The regular ratio is used
when you want to watch a 4:3 broadcast
or recorded program without modifying the
original picture to fit the dimensions of your
16:9 screen. The 4:3 picture will fill the
screen from top to bottom, while black bars
will appear to fill up the remaining space
along the picture’s sides. The 4:3 picture
will be centered within the boundaries of the
16:9 screen.
CINEMA - This ratio “zooms in” on the
center part of a 4:3 aspect picture, blowing
it up to fill the 16:9 screen.
CINEMA ZOOM - This ratio stretches
the High-Definition 16:9 aspect image to
eliminate the black surrounding bars.
FULL - This is the ratio to use when
watching 16:9 High-Definition broadcasts.
SLIM - This aspect mode shrinks the
screen of 16:9 to 4:3. There are some
programming that is already stretched by
mistake at broadcasting companies, so
this mode corrects it. Black side bars will
appear.
PANORAMA ZOOM - This ratio stretches
the High-Definition 16:9 aspect image to
eliminate the black side bars.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Aspect Ratios (Continued)
Press the ASPECT button
• By pressing the ASPECT button, you can change the size.
When you change the aspect ratios, it is different from their broadcast or recorded program.
NTSC, 480i, 480p
HD (1080i, 720p)
ATSC (1080i, 720p)
ATSC (480i, 480p)
ASPECT
PANORAMA ZOOM
CINEMA ZOOM
FULL
ASPECT
PANORAMA
CINEMA
ASPECT
PANORAMA ZOOM
CINEMA ZOOM
FULL
FULL
REGULAR
SLIM
Notes:
• You can also choose the size by pressing the π† buttons.
• When you change the aspect ratio or signal, reset the picture position to center.
• You can also access the FRONT PANEL CONTROL screen by using the MENU button
on the side of the TV instead of the remote control. It appears between INITIAL SETUP
and PICTURE ADJUST screen, and it has VIDEO STATUS and ASPECT menus. Choose
ASPECT by pressing Menu
+/- buttons ( OPERATE
†
®
on the side panel and choose a mode by using the CHANNEL
).
√
• "SLIM" can only be dispalyed when the signal is ATSC (480i or 480p).
• If the televison receives a 16:9 signal from your HDMI device, the aspect mode will turn to
FULL automatically. If the television receives a 4:3 signal from your HDMI device when you
are in FULL aspect mode, it will return to REGULAR aspect mode. If you change the aspect
mode after the televison changed it to FULL automatically, the televison will change to the
aspect mode you choosed.
Menu
The MENU button allows you to access JVC’s onscreen menu system. Press MENU to activate
the onscreen menu system.
• See individual topics like “Sound Adjust” for specific information on using menus.
OK
This button confirms your selection when you are in one of the onscreen menus.
Back
This button allows you to go back in the menu to change a selection or correct a mistake.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
TV/CATV Slide Switch
Use either the television’s own tuner or a cable box to select channels. Set this switch to TV to
operate the television’s built-in tuner. Move the switch to CATV to operate a cable box.
Note:
• See page 28 for information on programming your remote for cable box operation.
VCR/DVD Slide Switch
You can control a VCR or DVD player with the buttons on the lower part of the remote control.
Move the slide switch to VCR or DVD to operate.
Notes:
• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other
manufacturer’s brand VCR, please see the code chart and instructions on page 29.
• The remote is preset with the code 000 to control JVC-brand DVD players. For any other
manufacturer’s brand DVD player, please see the code chart and instructions on page 30.
VCR Buttons
You can use this remote control to operate the basic functions of your VCR. These functions
include: play, record, rewind, fast-forward, stop, pause, channel scan, TV/VCR, power on and
power off.
Move the selector switch to VCR to operate.
• The remote is preset with the code 000 to control JVC-brand VCR’s. For any other
manufacturer’s brand VCR, please see the code chart and instructions on page 29.
DVD Buttons
You can also use this remote control to operate the basic functions of your DVD player. These
functions include: play, rewind, fast-forward, stop, still/pause, previous/next, tray open/close,
power on and power off.
Move the selector switch to DVD to operate.
• The remote is preset with the code 000 to control JVC-brand DVD players. For any other
manufacturer’s brand DVD player, please see the code chart and instructions on page 30.
Light
All remote control buttons are illuminated, except for the TV/CATV slide switch, VCR/DVD slide
switch and Light button. Press the LIGHT button to turn the illumination on for 4 seconds.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Setup
Digital Setup
Use this function when you are receiving a digital broadcast.
Press the MENU button
Digital Setup
Antenna Level
π†
To DIGITAL SETUP
To enter
Digital Sound
PCM
4:3
è
Aspect Ratio
The onscreen will appear
Cable Card Application
i.LINK Auto Play
Software Update
OFF
Notes:
• Software Update will only appear when the SD Card
is inserted.
BACK
MENU
Select
Operate
Back
Exit
• If you are watching an analog channel, you can still
access the digital setup menu at anytime, while you are doing this, the background screen
will turn blank. In this case, the tuner will switch to digital, since you are accessing the digital
setup menu.
Antenna Level
Confirms the present antenna level.
Antenna Level
Press the MENU button
75
π†
To DIGITAL SETUP
To enter
BACK
MENU
è
Back
Exit
π†
To Antenna Level
To enter
è
Note:
• If you are watching an analog channel or a signal from your i.Link device, antenna level will
not appear.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Setup
Digital Sound
You can select the optical digital sound output, either PCM or Dolby Digital when your TV is
connected to an amplifier that has Dolby Digital decoder. If you select Dolby Digital, you can
enjoy listening in 5.1ch sound when watching digital broadcasts.
Press the MENU button
π†
è
To DIGITAL SETUP
To enter
π†
To Digital Sound
è
To select PCM or DOLBY DIGITAL
Press the MENU button when finished
Notes:
• If your amplifier does not have Dolby Digital decoder, select PCM. If you don't select PCM, it
cannot output the sound from the speakers.
• For connecting an amplifier using the optical output, see page 23.
Manufactured under license from Dolby Laboratories. "Dolby", and the
double-D symbol are trademarks of Dolby Laboratories.
Aspect Ratio
You can select the aspect mode for ATSC from 4:3 or 16:9.
Press the MENU button
π†
è
π†
è
To DIGITAL SETUP
To enter
To Aspect Ratio
To select 4:3 or 16:9
Press the MENU button when finished
Notes:
• Set the mode to 4:3 or 16:9 before you record a program using the ATSC MONITOR OUT.
• Make sure the mode you choose is the same as the TV’s aspect ratio when the recorded
program is played back, so that you can obtain a good picture quality, free from any unatural
distortions.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Setup
Cable Card Application
Press the MENU button
π†
è
π†
è
To DIGITAL SETUP
To enter
To Cable Card Application
To enter
Press the OK button
The application will perform
i.LINK Auto Play
When playing a D-VHS tape, you can set it to the i.LINK input automatically, or manually.
Press the MENU button
π†
è
π†
To DIGITAL SETUP
To enter
To i.LINK Auto Play
è
To select ON or OFF
ON: Set to i.LINK input automatically
OFF: Select the input manually
Press the MENU button when finished
Software Update
At first, insert the SD(Multi-media) card into the memory card slot. This function will appear
only when you insert an SD Card.
Press the MENU button
π†
è
π†
è
π†
To DIGITAL SETUP
To enter
To Software Update
To enter
Checks the card if it needs an update or not
Press the MENU button when finished
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Digital CH D/A (Digital/Analog)
The D/A button changes the analog and digital channel. Each time you press the D/A button,
you can switch back and forth the analog and digital channels. Digital channels have a "D" in
front of the channel number.
Note:
• If the cable card is inserted into the TV, you cannot use the D/A button. You can select a
digital channel only.
Press the D/A button
To watch digital channels
For example, to move to channel D23:
Press 2 (Two)
Press 3 (Three)
Press the TUNE button
Sub Channel
The main channel sometimes has minor channels (Sub Channels). By using the SUB button,
you can select a sub channel easily.
For example, to move to sub channel 123-45:
Press 1 (One)
Press 2 (Two)
Press 3 (Three)
Press the SUB button
Press 4 (Four)
Press 5 (Five)
Press the TUNE button
Note:
• If there are more than 2 major channels, select the digital channel by using the π† buttons
and then press the OK button.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
i.LINK Menu
i.LINK has two menus - Controller and Device.
By connecting a D-VHS VCR with an i.LINK cable, you can set the timer easily.
Notes:
• The i.LINK/Timer function will only work when you are receiving digital programming only.
• As for the connection of a D-VHS VCR with the i.LINK cable, see page 24.
• When operating the i.LINK, don't insert or disconnect the i.LINK cable.
Controller
You can operate a D-VHS VCR connected with an i.LINK cable by using this controller.
Notes:
• If the i.LINK is not connected, the Controller OSD will not appear. The OSD of device on
page 75 will appear.
• Some controller operations may differ from your D-VHS VCR operations.
Press the i.LINK MENU button
i.LINK
Controller
D-VHS1
STOP
00:00:00
POWER
Device
√®π† To select the key you want to operate
Press the OK button
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Device
To operate, select a device.
i.LINK
Controller
Device
Renumber
Page 2/3
D-VHS1
JVC
HM-DH30000U
D-VHS2
JVC
HM-DH40000U
HD-MOVIE 1
GR-HD1
JVC
π†
To select your device connecting with i.LINK
Press the OK button
Notes:
• If you do not select the device, you cannot use the i.LINK timer functions.
• When one device is selected and you select controller, you will move to the Controller
onscreen.
• The devices listed on the device onscreen are only D-VHS and HD-MOVIE that have i.LINK,
which can be recognized on this television. However, you can not record programs to HD-
MOVIE.
• If you disconnect one device, it will be removed from the list. Then, select Renumber to
rearrange the list in the new order.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Timer
You can set the two timers: Record and view. The timer starts the recording or turns to the
channel you set for it automatically.
Reservation
Press the TIMER button
π†
To New Reservation
Press the OK button
New Reservation
Timer
Rec
Timer Mode
Channel
Date
35-1
V
New Reserva
Sep. 10 (wed)
5:00PM
Start Time
End Time
80-3 PBS1D
6:00PM
Sep. 11 (Wed
335-1 KDVR
Weekly/Daily
Weekly
ON
i.LINK
i.LINK
R
R
R
Sep. 11 (Wed
Rec to i.LINK
335-1 KDVR
Sep. 18 (Wed
Set Timer
35-1 PBPBP
Sep. 18 (Wed
Cancel
†
è
†
To Timer Mode
To select Rec or View
To Channel
è
†
To select the channel you want to set the timer for
To Date
è
†
To select the date
To Start Time
è
†
To set the start time
To End Time
è
†
To set end time
To Weekly/Daily
è
†
To select Once, Weekly, Daily(Sun.-Sat.), Daily(Mon.-Sat.) or Daily(Mon.-Fri.)
To Rec to i.LINK
è
To select ON or OFF
†
To Set Timer
Press the OK button
R
If you set the Rec on timer mode, set recording
title.
is added in front of the program
is added in front of the program
If you set the View on timer mode, set viewing
title.
V
Notes:
• In order for the timer setting to work, you must set the clock on your television. See page
57.
• When you want to edit the timer settings, see Timer Edit on page 77.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Timer Edit
When you want to confirm the timer you set or edited, or delete the timer setting, use this
function.
Timer Edition
Press the TIMER button
π†
To select the timer list you want to edit
Press the OK button
Timer Edit
Timer
Rec
Timer Mode
Channel
Date
35-1
V
New Reserva
Sep. 10 (wed)
5:00PM
Start Time
End Time
80-3 PBS1D
6:00PM
Sep. 11 (Wed
335-1 KDVR
Weekly/Daily
Weekly
ON
i.LINK
i.LINK
R
R
R
Sep. 11 (Wed
Rec to i.LINK
335-1 KDVR
Sep. 18 (Wed
Set Timer
35-1 PBPBP
Sep. 18 (Wed
Cancel
Delete
√®π† To change the setting you want to edit
†
To Set Timer
Press the OK button
Timer Deletion
Press the TIMER button
π†
π†
To select the timer list you want to delete
Press the OK button
To Delete
Press the OK button
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Button Functions
Cancel the timer recording
When you record a digital program now, you can cancel the recording.
Press the TIMER button
Timer
Sep. 10 (Wed) 4:55PM
Page 1/1
π†
To select the timer list you want to cancel
the recording
New Reservation
80-3
V
R
Do you want to terminate current program?
Press the OK button
Sept
335-
Sept
i.LINK
N
o
Y
e
s
The message "Do you want to
terminate current program ?" will
appear.
è
To select
YES: Cancel the recording
NO: Continue the recording
Press the OK button
Guide
You can view the program from the GUIDE.
Notes:
• The GUIDE function will only work when you are receiving digital programming only.
• The GUIDE will not show the correct time and date if you have not performed the set clock
function on your television. See page 57.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Information
Weak Signal
This OSD warning appears when the digital channel that you have selected is too weak to
receive or no signal is being detected for that channel.
Weak Signal
15
No Program
If the TV channel you selected, or were watching is not receiving a signal, "NO PROGRAM"
appears on the television screen. It appears when that channel is not receiving a signal and you
have the Noise Muting function OFF and you have a single screen. It moves automatically every
two seconds to prevent the screen from burn-in.
Note:
• Even if "NO PROGRAM" appears on the screen, your timer functions and auto shut off
functions that you set, are still active.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Card Information
Cable card offers information when a cable card is inserted into the CABLE CARD slot on the
back of the television.
Notes:
• Please contact your local cable company regarding detailed information.
• When the cable card is inserted into the cable card slot, if you turned the power off, the fan will
continue to rotate because the program information is being renewed. This is normal.
Cable Card Connection
C
S
AT
/ DIGIT
CABLE IN
AL
DIGITAL-IN
Cable Card
CARD
Note for inserting Cable Card:
• When you are watching a digital program, and if a weather or government emergency occurs,
the following may occur automatically regardless of what channel you were watching: the
channel may change, the screen will disappear or important text will appear on the screen.
The information is transmitted from EAS (Emergency Alert System), Firmware Upgrade of
Cable Card or compulsory HTML.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Refer to the table below to check the condition. If you think that there is a problem, contact the
JVC Service Center where you purchased the television.
PROBLEMS
CHECK
There is no power
• See if the power cord became unplugged.
• Check for a blown fuse or circuit breaker or a power outage.
There is no picture
or sound
• The antenna could be disconnected.
• The input mode could be set improperly. See page 61.
• The tuner (Auto Tuner Setup) could be set improperly. See page 35.
• The TV station may be having difficulties. Check to see if other stations are working.
Remote control is not • Check to see that the batteries are still working and properly installed.
operating properly or • Make sure the remote has a clear sight path to the TV.
at all
• Check that the TV/CATV switch is in the proper position.
• You may be too far from the TV. You must be within 23 feet (7 meters).
You cannot select a
certain channel
• Make sure the channels have been programmed. See "Channel Summary", page 36.
• Check to see if the channel is locked. See "Channel Summary - Lock" page 37.
The power turns off
by itself
• Make sure the set did not become unplugged.
• Perhaps the On/Off Timer is set. See page 58.
• Check to see if the Sleep Timer was set. See page 64.
It does not operate
correctly
• This television is operated by a microprocessor. It is possible that external noise or
interference is causing the problem. If the television does not function correctly, remove the
electrical plug from the wall outlet and wait a while before inserting it into the wall outlet
again and operating the television.
The clock is wrong
• The power was interrupted and the clock was not reset. See page 57.
The color quality
is poor
• Tint and Color may be improperly adjusted. See page 53.
• The Video Status mode may be turned to the wrong setting. See page 63.
There are lines
across the picture
• There could be interference from another electrical appliance, such as a computer,
another TV or VCR. Move any such appliances further away from the TV.
• There could be interference from a high-wattage appliance, like a hairdryer or vacuum,
operating nearby. Move the antenna away from the appliance or change to a coaxial
cable connection which is less prone to interference.
The picture is spotted
There are double
pictures (ghosts)
• A building or passing airplane can reflect the original signal and produce a second,
slightly delayed one. Adjust your antenna position.
Picture is snowy
(image noise)
• Your antenna may be damaged, disconnected or turned. Check the antenna
connection. If the antenna is damaged, replace it.
Screen is 80% black
• The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 46.
• Make sure the MTS settings are correct. See page 64.
Stereo or bilingual
programs can't be
heard
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
PROBLEMS
CHECK
Static electricity
• It is normal to feel static electricity if you brush or touch the screen.
You hear occasional
crackling sounds
• It is normal for the TV to make crackling sounds when first turned on or off. Unless
the sound or picture become abnormal, this is fine.
The AUTO DEMO
• The On Timer that you programmed has started.
finished automatically • The channel that the AUTO DEMO is using is a channel that is blocked by V-Chip.
• The Auto Shut Off that you programed has occured.
It does not operate
correctly
• Press the CHANNEL- and VOLUME- buttons on the front panel of the TV simultaneously
for a few seconds. The Digital Tuner will be reset. If this does not reset it correctly, unplug
the power cord and plug it back in.
The following are not malfunctions.
•
The television may make a creaking sound if the temperature of the room or the
temperature of the inside of the television changes. If there is no problem with the screen or
sound, then there is no need to worry.
•
Although the picture may be temporarily disturbed and noise may be seen on the screen if
the power is turned on immediately after it has been turned off, this is not a malfunction.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
LT-26X776
LT-32X776
LT-37X776
Type
LCD Flat Television
Reception Format NTSC, BTSC System (Multi-Channel Sound) ATSC Terrestrial, Digital Cable
VHF 2 to 13, UHF 14 to 69 CATV 135 Sub, Mid, Super, Hyper
and Ultra bands (191 channel frequency synthesizer system)
Reception Range
• Reception of channel A-5 ("95" of the TV set's on-screen cable channel
numbers) is not recommended for your TV set.
Power Source
AC 120V, 60 Hz
Power Consumption
139W
173W
202W
26 inch / 64.8 cm
measured diagonally,
16:9 ratio
32 inch / 80.2 cm
measured diagonally,
16:9 ratio
37 inch / 94.9 cm
measured diagonally,
16:9 ratio
Screen Size
Audio Output
Speakers
10W + 10W
6.6 cm round x 2
6.6 cm round x 4
Antenna Terminal
(VHF/UHF,
75 ohms (VHF/UHF)(F-type connector)
ATSC/DIGITAL
CABLE IN)
Video: 1 Vp-p, 75 ohms
Audio: 500 mVrms (-4dBs) high impedance
External Input Jacks
Component Input
Jack
Y: 1Vp-p positive, 75 ohms (negative sync provided)
Pb/Pr: 0.7 Vp-p 75 ohms
Y: 1Vp-p positive, 75 ohms (negative sync provided)
C: 0.286 Vp-p (burst signal), 75 ohms
S-Video Input Jacks
Monitor/Recording
Output
Video: 1Vp-p, 75ohms
Y: 1Vp-p positive, 75 ohms (negative sync provided)
C: 0.286 Vp-p (burst signal), 75 ohms
Audio: 250mVrms (-10dBs)
Fs-18dB Low Impedance
Optical Output
Digital Audio
Digital Out (optical) x 1
TS IN/OUT (4-pin, S400) x 2
IEEE1394 compliant DTCP digital copy protection compatible
i.LINK In/Out Jack
Digital–In
HDMI jack x 1
Note: The Digital–In terminal is not compatible with picture signals of a
personal computer
36 1/2 x 27 1/8 x 12 7/8
Dimensions (inch/cm)
W X H X D
27 3/4 x 21 7/8 x 12 1/4
(with stand)
31 7/8 x 24 3/4 x 12 1/4
(with stand)
(with stand)
92.6 x 68.7 x 32.5
(with stand)
70.3 x 55.3 x 30.9
(with stand)
80.8 x 62.8 x 30.9
(with stand)
27 3/4 x 19 1/8 x 4 5/8
(without stand)
31 7/8 x 22 x 4 5/8
(without stand)
36 1/2 x 24 7/8 x 4 3/8
(without stand)
70.3 x 48.3 x 11.5
(without stand)
80.8 x 55.9 x 11.6
(without stand)
92.6 x 63.2 x 10.9
(without stand)
43.2 / 19.6 (with stand)
44.9 / 20.4 (with stand)
61.6 / 27 (with stand)
Weight (lbs / kg)
35.9 / 16.3 (without stand)
37.6 / 17.1 (without stand)
47.7 / 21.7 (without stand)
Accessories
Refer to "unpacking your TV", page 9
Specifications subject to change without notice.
• The open source software is embedded in this product. For more information, please go to:
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
87
Download from Www.Somanuals.com. All Manuals Search And Download.
JVC COMPANY OF AMERICA
Division of JVC Americas Corp.
1700 Valley Road
JVC CANADA, INC.
21 Finchdene Square
Scarborough, Ontario
Canada, M1X 1A7
Wayne, New Jersey, 07470
Download from Www.Somanuals.com. All Manuals Search And Download.
|