Digital Camera
GC-A70
INSTRUCTIONS
Thank you for purchasing this JVC product. Before beginning to operate this
unit, please read the instruction manual carefully in order to make sure that the
best possible performance is obtained. If you have any question, consult your
JVC dealer.
To HomePage of JVC
LNT0011-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, it may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
z
z
z
z
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not approved by JVC could void user’s authority to operate the equipment.
Contact
Address: JVC AMERICAS CORP.,
1700 Valley Road, Wayne, New Jersey 07470
Telephone: (973) 317-5000
INFORMATION (for CANADA)
This Class B digital apparatus complies with Canadian ICES-003.
RENSEIGNEMENT (Pour le CANADA)
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTIONS
About moisture condensation . . .
You may have observed that pouring a cold liquid into a glass will cause drops of water to form on the glass’ outer
surface. This same phenomenon occurs on the lens of the camera when it is moved from a cool place to a warm place,
after heating a cold room, under extremely humid conditions or in a place directly subjected to the cool air from an air
conditioner.
Serious malfunctioning
If malfunctioning occurs, immediately stop using the unit and remove the battery, then consult your local JVC dealer.
MAIN UNIT
1. For safe use, please do NOT . . .
...open the camera’s chassis due to high voltage inside.
...disassemble or modify the unit.
...allow inflammables, water or metallic objects to enter the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
...remove the batteries while the power is on.
...look through the viewfinder directly at the sun or extremely bright light.
...point the lens directly into the sun. This can lead to malfunctioning of the internal circuitry. There is also a risk of fire
or electric shock.
...subject it to shock or excessive vibration.
...connect any USB cable to this unit except the one provided.
2. Avoid using the unit in the following places:
z
z
z
Where the camera will be subject to dust, soot, steam, or excessive heat.
Where the camera will be subject to excessive shock or vibration.
Where the camera will be subject to extremely low (under 0°C or 32°F) or extremely high (over 40°C or 104°F)
temperatures.
z
z
z
z
z
In direct sunlight.
In a closed car in summer.
Near a heater.
Near a television set.
Near appliances generating strong magnetic or electric fields (speakers, broadcasting antennas, etc.).
3. To protect the unit, DO NOT . . .
...allow it to become wet.
...drop the unit or strike it against hard objects.
...subject it to shock or excessive vibration during transportation.
...keep the lens directed at extremely bright objects for long periods.
...swing it excessively when using the hand strap or neck strap.
MEMORY CARDS
1. To properly use and store your memory cards, be sure to read the following cautions:
z
z
z
Make sure the memory card bears the SD or Multimedia Card mark.
Make sure the memory card is positioned properly when inserting.
While the memory card is being accessed (during recording, playback, deletion, formatting etc.), never unload the
memory card or turn off the digital camera.
z
Store memory cards...
...away from heaters or other heat sources.
...out of direct sunlight.
...where they will not be subject to unnecessary shock or vibration.
...where they will not be exposed to strong magnetic fields (such as those generated by motors, transformers or
magnets).
LCD MONITOR
z
To prevent damage to the LCD monitor, do NOT subject it to undue force or shocks.
z
To prolong its service life, avoid rubbing it with a coarse cloth.
ALKALINE BATTERIES
1. For safe use, do NOT . . .
...attempt to charge the alkaline batteries.
...reverse the polarities of the batteries.
...carry or store a battery together with objects such as metal pens, necklaces, coins or hairpins. This could short-
circuit the positive and negative poles of the battery.
...heat or attempt to disassemble a battery.
...expose the battery to water or fire.
...subject a battery to strong impacts, such as hitting it with a hammer, stepping on it or dropping it.
...forget to remove the batteries from the unit if the camera is not to be used for an extended period of time, so as to
prevent leakage.
Any of these may cause the battery to split or leak, causing fire or injury.
2. Use only the specified batteries with this camera. The use of other power sources may cause a fire.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. When discarding batteries, environmental problems must be considered and the local rules or laws governing
the disposal of these batteries must be followed strictly.
HOW TO HANDLE A CD-ROM
z
Take care not to soil or scratch the mirror surface (opposite to the printed surface). Do not write anything or put a
sticker on either the front or back surface. If the CD-ROM gets dirty, gently wipe it with a soft cloth outward from the
center hole using a circular motion.
z
z
z
Do not use conventional disc cleaners or cleaning spray.
Do not bend the CD-ROM or touch its mirror surface.
Do not store your CD-ROM in a dusty, hot or humid environment. Keep it away from direct sunlight.
FLASH
z
Do not fire the flash at a person, particularly an infant, at short range for this may cause impairment of eyesight.
z
Do not touch light-emitting portion after flash. This may cause burn.
BEFORE USING THE CAMERA
z
We recommend that you take some test shots before you actually start, to accustom yourself to the camera.
z
We cannot bear any responsibility for an inability to shoot, record, or play back material normally in the event of a
problem with this camera.
z
z
z
z
We shall not be liable for any incidental, consequential or exemplary damage, loss of profits or any demand made by
any third party due to your use of this product or the provided software.
Store backups of important images/video clips on a personal computer, etc. We cannot bear any responsibility for
pictures stored in memory that are lost or altered.
It is prohibited to use still images/video clips taken with this camera for commercial purposes without the consent of
the copyright owner.
Please be aware that the shooting subject may appear whitish or halation may occur in following conditions:
{
When a very bright subject is taken in a short distance.
{
When a subject which has a very bright part is taken in strong sunlight.
Notes:
z
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States
and/or other countries.
z
Other trademarks are the properties of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
FUN THINGS YOU CAN DO
This camera is an all-in-one compact size digital and USB PC-camera. With it, you can:
z
z
z
Take digital pictures/video clips in an instant.
Easily capture digital images and download them to your computer.
Videoconference on the Internet.
Keep in touch with distant family and friends. See and talk with people on the Internet face-to-face.
Send captured images with your e-mail messages.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
WHAT'S INCLUDED?
Please check to see that the following items are included in the package. If any item is missing, please enquire at your
nearest JVC-authorized dealer.
Notes:
z
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States
and/or other countries.
z
Other trademarks are the properties of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
SYSTEM REQUIREMENTS (PC)
z
z
z
z
z
z
z
Microsoft® Windows® 98/98SE/Me/2000/XP (Pre-installed Model)
Intel® Pentium® Processor 166 MHz or higher
Free USB Port
Minimum RAM: 32 MB (Windows XP: 128 MB)
250 MB of available hard disk space
Color display: 800x600 or better
CD-ROM drive
Notes:
z
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States
and/or other countries.
z
Other trademarks are the properties of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
FEATURES
LCD Monitor
A 1.5-inch color TFT LCD monitor with high image quality of 2 megapixels that enables monitoring
of images while shooting, and immediately after recording.
Design
Features a compact, posh metallic design.
Digital Zoom
Digital zooming of x2, x3 and x4 and macro mode (switching by lens) with a 45 cm close-up
capability for wide variety of shooting scenes.
Multipurpose
A Digital Still Camera, usable as a movie camera (Video Clip: AVI w/o Sound) or Webcam as well
as a Multi Digital Camera.
Built-in Digital
Memory
Equipped with built-in 8 MB flash memory (that retain images even in the absence of a power
supply) and SD/MMC compatible memory slot, the number of images can be increase simply by
adding memory card.
Power Supply
Supplied by easily purchased AA-size alkaline batteries (x2, option).
In addition, it operates with USB power source when connected to a PC through a USB port (i.e.
when transferring images from the built-in memory to the PC or using as a Webcam).
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
GETTING TO KNOW THE CAMERA
Controls, Connectors and Indicators
Built-in Flash
Viewfinder window
Self-Timer lamp
Lens
Normal
/ Macro switch dial
USB port
Strap holder
USB Port Cover
Shutter button
[RESOLUTION] &
Quality / Left button
Status indicator
Viewfinder
[DISPLAY] /Up
button
[OK/ ZOOM] button
Flash mode /Right button
[POWER] button
[MODE] button
Self-Timer
/Down
button
[MENU] button
LCD monitor
Battery/Memory Card
compartment door
Tripod socket
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
GETTING STARTED
Be sure to insert the (AA-size Alkaline) batteries before trying to capture images with your camera.
Inserting the Batteries
1. Slide the Battery/Memory card compartment door (located on the right
side of the camera) in the direction indicated by the arrow to open it.
2. Insert the AA-size batteries as indicated on the inner side of the door.
3. Close back the door and turn on the camera.
Checking Batteries(
: Full battery power)
The Battery Indicator will be displayed on the status LCD monitor while the
camera is on. Depending on the durability and usage of the batteries, the
number of pictures that can be recorded varies. Note that power is
consumed by the following operations even when not recording, reducing
the number of images that can be recorded.
z
z
Extensive use of the LCD monitor in the Play/Erase mode.
Performing settings.
Notes:
z
z
z
z
Please ensure that the batteries are inserted in the correct way. Do not reverse the and polarities.
The recommended battery type is AA size ALKALINE.
Never use manganese batteries.
Low temperatures (under 0°C or 32°F) will reduce the output efficiency of the batteries, thereby shortening the
operation time of the camera.
z
z
z
z
z
The use of Flash is not recommended when the battery level is low.
Never mix old and new batteries.
Remove the batteries if the camera is not to be used for an extended period of time, to prevent leaks or corrosion.
Before discarding batteries, cover the positive and negative terminals with adhesive tape.
The Battery Indicator reflects the level of remaining battery power. When the indicator appears as shown above, the
batteries are weak and need to be replaced.
Attaching the Hand Strap or Neck Strap
Always use the provided hand strap or neck strap when carrying the camera. Please note that the company cannot be
held responsible for any accidental drop of the camera due to improper use of the hand strap or neck strap.
To attach the strap to your camera:
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Thread the thinner looped end of the strap through the strap holder.
2. Insert the other end of the strap through the thin loop and pull it all the way out. Ensure that the strap is securely
tightened unto the camera.
Note:
z
Be careful not to bump the camera or entangle the strap.
Inserting and Removing the SD / Multimedia Card
This camera can be used with either an SD card or a Multimedia card (MMC).
When traveling and capturing a lot of images, it is convenient to make use of an SD or a Multimedia card. When a card is
inserted into the camera, still images/video clips captured will be stored in the card’s memory.
When the card is removed, the camera’s internal memory will be used as the storage media.
Inserting the Memory Card
1. Turn off the camera's power by pressing the [POWER] button.
2. Open the Battery/Memory card compartment door.
3. Firmly insert the memory card into the memory card slot as far as it can go,
with the memory card electrodes (metal contacts) end facing the camera.
(Refer to the right figure.)
4. Close back the door firmly.
Removing the Memory Card
1. Turn off the camera's power by pressing the [POWER] button.
2. Open the Battery/Memory card compartment door.
3. Push the memory card in as far as it can go and release. The card will
spring back and protrude slightly. Pull it out with your fingers.
4. Close back the door firmly.
Notes:
z
z
z
z
SD and Multimedia cards are purchased separately.
Pay attention to the card direction when inserting. Wrong direction and forced insert can break it.
When the memory card is inserted, access to the camera's internal memory is not possible.
Cards available in the market, and those already formatted for PC and other devices may not be identified by this
camera. Therefore, before using them, it is necessary to format them first with this camera.
z
z
z
While the power of the camera is on, do not open the battery cover to replace the memory card or batteries as this
may cause irrecoverable corruption of card data.
The memory card is a sensitive device so it should not be subject to any shock. Do not touch the metal part of the
card with your hand.
When the memory card is write-protected, it cannot be used (A message “WRITE PROTECT” will appear on the LCD
monitor). You have to disable the write-protection first.
Switching the Power ON / OFF
Press the [POWER] button to toggle ON / OFF.
The Status Indicator will lit up immediately upon power on. The light will
go off after a while (the length of time varies with the capacity of the
memory card that is inserted in the camera) and the camera will then
be ready for use.
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the LCD Monitor ON / OFF
The LCD monitor is automatically activated when the power is switched
on. However, since the LCD monitor consumes battery power fast, we
recommend that you turn off the LCD monitor and use the optical
viewfinder as far as possible when capturing still images. To switch the
LCD monitor ON or OFF, toggle the [DISPLAY]/Up
button. When the
LCD Monitor is OFF, the status indicator lights up to indicate Power ON
status.
Notes:
z
The “DATE/TIME” setting screen will appear on the LCD monitor upon its activation in the case of a newly purchased
camera or if the camera has not been used for a long time.
z
When the camera is in the Play/Erase mode, the LCD monitor cannot be turned off. The still image/ video clip taken
most recently will be shown on the LCD monitor. Further, in the case that no image/video clip exists in the memory,
the message “NO IMAGE” will be shown on the LCD monitor. When the camera is in the Video Clip Mode, the LCD
monitor cannot be turned off either.
z
When no operation is performed within a certain time interval (user set value: “1min”, “3min”, “5min”, “10min”,
“Cancel”; Default value: “3min”), the camera will automatically turn off.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
OPERATIONS
CAMERA MODE
PLAY /ERASE MODE
Play Basics
VIDEO CLIP MODE
Shooting Basics
Shooting Basics
Customized Shooting
z
z
z
z
Zooming
Using Flash
Using Self-Timer
Setting the Image Resolution &
Quality
Customized Shooting is not applicable to the Video Clip and Play/Erase Mode.
Menu Settings
z
z
z
“SETUP MENU”
“QUICK VIEW”
z
z
“SETUP MENU”
“EV&WHITE BALANCE”
z
z
z
z
z
“SETUP MENU”
“SLIDE SHOW”
“ERASE”
“COPY TO CARD”
“DPOF”
“EV&WHITE BALANCE”
Setting the various mode:
1. Press the [POWER] button.
2. Press the [MODE] button until the desired mode is displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
CAMERA MODE
This mode is used for capturing still images. The images captured will be stored in the camera’s internal memory or the memory-
card in JPEG file format.
LCD monitor status display
Memory Card Indicator
Camera mode Indicator
Resolution & Quality Indicator
Number indicator
Built-in Flash Indicator Indicator
Self-Timer indicator
Zoom Indicator
EV Level Indicator
White Balance Indicator
Battery Indicator
Macro Indicator
1. Resolution & Quality Indicator
Full resolution (1600x1200 Pixels) & Fine quality
Full resolution (1600x1200 Pixels) & Normal quality
Middle resolution (1280x960 Pixels)
Low resolution (640x480 Pixels)
2. Memory Card Indicator
Appears when SD Card is inserted.
Appears when MMC card is inserted.
Will not be displayed when no memory card is being inserted.
(Uses internal memory.)
No Indicate
3. Number Indicator
Number of images that can be stored.
4. Built-in Flash Indicator
The flash fires automatically according to the photography conditions, is suitable for general photography.
Use this mode to avoid the red-eye effect when photographing people in low-light conditions.
Use this mode in the environment where the use of flash is prohibited or under the situation where the distance to
the subject is too far away for the flash to have any effect.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Self-Timer Indicator
2 sec Self-Timer mode. Shooting begins 2 seconds after pressing the shutter button.
10 sec Self-Timer mode.Shooting begins 10 seconds after pressing the shutter button.
No Indicate Will not be displayed when Self-Timer is not being set.
6. Zoom Indicator
Appears when Digital Zoom is set to 2 times.
Appears when Digital Zoom is set to 3 times.
Appears when Digital Zoom is set to 4 times.
No Indicate Will not be displayed when Digital Zoom is not being set. [1x]
7. EV Level Indicator
Adjust the EV Level by EV & White Balance setting, and the adjusted value will be displayed.
[-2.0 - +2.0]
It is not displayed at default value [0].
8. White Balance Indicator
Adjust the White Balance by EV & White Balance setting, and the adjusted value will be displayed.
[
]
It is not displayed at default value “AUTO”.
9. Battery Indicator
Battery Life > 40%
20% < Battery Life < 40%
10% < Battery Life < 20%
Battery Life < 10%. Status Led flash 5 sec and then power off.
10. Macro Indicator
It is displayed when the Normal / Macro switch dial is set to Macro
.
When set to Macro, it is possible to focus the camera on the subject in the proximity of about 45 cm.
Shooting Basics
When the card is inserted into the camera, your captured still images/video clips will be stored in the card’s memory. When the car
is removed, the internal memory of the camera will be used as the storage media.
Procedures:
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Get the camera ready. (Refer to “Getting Started”)
2. Toggle the [MODE] button to select the Camera mode [ ].
3. Turn the Normal / Macro switch dial to Normal
.
4. Frame your subject. You may use either the viewfinder or the 1.5" full color TFT LCD monitor (Toggle the [DISPLAY]/ Up
button to activate or deactivate it)
* We recommend, however, that the viewfinder be used as far as possible to extend battery time since the LCD is highly
power consumptive.
5. Press the shutter button fully down.
If the “QUICK VIEW” function has been set to ON, the image captured will appear on the LCD monitor for a few seconds.
6. To continue capturing, repeat the above steps 4 & 5.
Notes:
z
z
z
To adjust the Image Quality and Resolution, please refer to “Setting the Image Resolution and Quality”.
When the storage memory is full, you may either erase the images that are no more required, or insert a new memory card.
The number of remaining shots shown on the LCD monitor is an approximate value based on the currently set resolution,
picture quality and memory size.
z
The actual number of remaining shots also differ depending on the shooting conditions. Hence, a single shot may reduce the
value by two or not change the value at all. This is not a malfunction of the LCD monitor. Also, upon the camera being turned
on, memory adjustments are made and the indicated remaining value may actually be higher than when the camera was last
turned off.
z
z
z
z
z
z
z
When you take pictures in bright locations or in clear fine weather, lines may appear on the monitor. This is not a malfunction.
Press the shutter button down steadily.
When the Status Indicator is lit, shooting/replay is not possible. Wait until the light goes off.
Never open the Battery/Memory card compartment door when the Status Indicator is lit for this may cause malfunction.
Please format new Memory cards with this camera before using them.
We recommend that you take some test shots to get accustomed to the camera before you actually start.
We cannot bear any responsibility for an inability to record or replay material normally, in the event of a problem with this
camera.
z
z
Store backups of important images in eg. your personal computer. We cannot bear any responsibility for any loss or alteration
to the images stored in the camera’s internal or external memory.
It is prohibited to use images taken with this camera for commercial purposes without the consent of the copyright owner.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
Customized Shooting (CAMERA MODE)
(1) Zooming
This mode allows you to zoom up on your subject, making it appear larger (2x, 3x, 4x) and closer.
Procedures:
1. Ensure that the camera is turned on.
2. Select the Camera mode with the [MODE] button.
3. Press the [OK/ZOOM] button to activate the digital zoom function. The image on the LCD monitor will be enlarged.
With each press, the image will change in the sequence of 2x, 3x, 4x and zoom off.
4. Frame your subject. Then, press the shutter button fully down. (For details, see “Shooting Basics”)
(2) Using Flash
The flash is designed to fire automatically when required. (Default setting: Auto ). To suit the different conditions,
however, you can change the flash mode. Press the Flash mode button until the desired flash mode (Auto , Red-Eye
Reduction
, Off
) is indicated.
Procedures:
1. Ensure that the camera is turned on.
2. Select the Camera mode with the [MODE] button.
3. Press the Flash mode /Right button until the desired flash mode (Auto , Red-Eye Reduction
indicated.
, Off
) is
4. Frame your subject. Then press the shutter button fully down. (For details, see “Shooting Basics”)
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Flash
Red-Eye
The flash fires automatically according to the photography conditions. It is suitable for general
photography.
Use this mode to avoid the red-eye effect when photographing people or animals in low light
Reduction (RER) conditions.
Used where the use of flash is prohibited or when utilizing the night view/indoor lighting for shooting.
The flash mode can also be turned off when the distance to the subject is too far away for the flash to
have any effect.
Flash Off
Notes:
z
z
z
When shooting using flash, although the flash fires twice but the actual shoot is at the second flash. The first fire is to
determine whether flash is required. The second flash will not be fired if it is not required.
The red-eye reduction function may have little effect if the subject is not directly facing the pre flash or main flash, or
when the distance between the camera and the subject is too far.
Flash cannot be used during Macro function. It automatically becomes Flash Off.
(3) Using Self-Timer
This unit includes 2 seconds and 10 seconds Self-Timer function.
With the 10 seconds Self-Timer function, the photographer too, can
get into the frame when taking group pictures.
Moreover, when you take pictures in dark locations, the shutter
speed may become slow, setting the 2 seconds Self-Timer will
prevent the picture from blurring due to shaking of the camera while
pressing the shutter button.
Procedures:
1. Ensure that the camera is turned on.
2. Select the Camera mode with the [MODE] button.
3. To activate the Self-Timer, press the Self-Timer /Down
The 10 seconds Self-Timer indicator will appear on the LCD monitor
as shown on the right. Pressing it again will change to 2 seconds
Self-Timer.
button.
4. Frame your subject and press the shutter button. The Self-Timer
lamp will start blinking for 10 seconds (slowly in the first 7 seconds
and rapidly in the remaining 3) or 2 seconds (rapidly blinking only).
At the end of the 10 seconds or 2 seconds, the shutter will be
released.
Note:
z
When capturing images using the Self-Timer, do stabilize your camera with eg. a camera stand.
(4) Setting the Image Resolution and Quality
Users can choose from four image resolution & quality setting, namely:
To set the Image quality and resolution, press the [RESOLUTION] & Quality/Left button until the desired setting is
indicated.
Download from Www.Somanuals.com. All Manuals Search And Download.
The number of images that can be stored
The number of images (approximate) that can be stored in the memory card at the current image quality and
resolution is reflected on the LCD monitor. Varying the image quality and resolution settings will affect the number of
storable images. The following shows the approximate number of storable images based on 8 MB of available
memory (when the camera is first turned on), as the image quality and resolution is varied.
Indication on LCD
Resolution
Quality
Fine
Initial Estimated Storage with 8 MB Memory
monitor
1600F
1600N
1280
1600x1200
1600x1200
1280x960
640x480
10
20
40
80
Normal
-
-
640
Notes:
z
The number of recordable images also varies with the subject and the capacity of the memory card.
z
The number of remaining images that can be recorded, shown on the LCD monitor, will decrease by 1 every time
you take a new shot. If, however, the file size is too minimal, the number will remain the same after the shot is
taken. By the same token, the number will decrease by more than 1 if the file size is too large.
(5) Using Macro
By using the Macro function, it is possible to shoot at a close range (about 45 cm).
Procedures:
1. Ensure that the camera is turned on.
2. Select the Camera mode with the [MODE] button.
3. Turn the Normal /Macro switch dial to Macro
.
4. Frame your subject. Then press the shutter button fully down. (For details, see “Shooting Basics”)
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal
Setting
This is usually used when shooting. It is in focus with the
subject that is about 1.9 m away.
Macro Setting For shooting the subject at a close-up range. It focuses in the
proximity of about 45 cm.
Notes:
z
If you use the viewfinder to take a picture in Macro mode, the field visible through the viewfinder does not match the
field actually photographed because the viewfinder and lens are in different positions. Accordingly, you should use the
LCD monitor to take pictures in Macro mode.
z
z
z
Flash cannot be used during Macro function. It automatically becomes Flash Off.
Do not turn the Normal /Macro switch dial unnecessarily. It may become malfunction.
Please take note not to touch the lens when turning the dial.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
VIDEO CLIP MODE
This mode is used for shooting video clips. The video clips will be stored in the camera’s internal memory or the memory
card in AVI File Format.
Total available recording time
The total available recording time (approximate) is reflected on the LCD monitor. For video clips, the Resolution is fixed at
320x240 and the Image Quality cannot be changed. The following shows the approx. length of recording time based on 8
MB of available internal memory (when the camera is first turned on):
The actual recording time changes in accordance with the images of the Video Clip taken.
Indication on LCD
monitor
Initial Estimated available
recording time
Resolution
Quality
320x240
-
320
46 sec
LCD monitor status display
Video Clip mode Indicator
Memory Card Indicator
Resolution & Quality Indicator
Remain Time Indicator
[Rec] icon
EV Level Indicator
White Balance Indicator
Battery Indicator
Macro Indicator
1. Resolution & Quality Indicator
Video Clip Mode has only one resolution of 320x240.
2. Memory Card Indicator
Appears when SD Card is inserted.
Appears when MMC card is inserted.
Will not be displayed when no memory card is being inserted.
(Uses internal memory.)
No Indicate
3. Remain Time Indicator
Remain movie time which is display by Count down.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. [Rec] icon
Appears when recording Video Clip to indicate that recording is in progress.
5. EV Level Indicator
Adjust the EV Level by EV & White Balance setting, and the adjusted value will be displayed.
[-2.0 - +2.0]
It is not displayed at default value [0].
6. White Balance Indicator
Adjust the White Balance by EV & White Balance setting, and the adjusted value will be displayed.
[
]
It is not displayed at default value “AUTO”.
7. Battery Indicator
Battery Life > 40%
20% < Battery Life < 40%
10% < Battery Life < 20%
Battery Life < 10%. Status Led flash 5 sec and then power off.
8. Macro Indicator
It is displayed when the Normal /Macro switch dial is set to Macro
.
When set to Macro, it is possible to focus the camera on the subject in the proximity of about 45 cm.
Shooting Basics
Procedures:
1. Get the camera ready. (Refer to “Getting Started”)
2. Toggle on the [MODE] button to select the Video Clip Mode [ ].
3. Adjust the Normal /Macro switch dial to either Normal
4. Press the shutter button to start recording.
or Macro to suit the distance of the subject.
5. Press the shutter button again to stop recording.
6. To continue shooting, repeat the above steps 4 to 5.
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
z
z
z
When the storage memory is full, you may either erase the video clips that are no more required, or insert a new
memory card.
The remaining shooting time shown on the LCD monitor is an approximate value based on the currently accessed
memory size.
The actual number of seconds available for shooting also depends on the shooting conditions. The value does not
necessarily decrease by the second. Also, upon turning on the camera, memory adjustment is made and the
available time may actually be more than when the camera was last turned off.
z
When you take pictures in bright locations or in clear fine weather, lines may appear on the monitor. This is not a
malfunction.
z
z
Press the shutter button down steadily.
When the status indicator is lit, shooting/replay is not possible. Wait until the light goes off. (After shooting a video
clip, you would have to wait a little while for the pictures to be stored into memory. A few seconds is also required to
load the images from the memory to the LCD monitor for replay).
z
z
z
Never open the Battery/Memory Card compartment door when the status indicator is lit for this may cause damage.
Please format new Memory cards with this camera before using them.
In the Video Clip mode, the following functions are not possible.
* Voice/sound recording.
* Use of flash.
* Self-Timer.
* Zoom.
* Image Quality setting. (The Video Clip mode resolution is fixed at 320x240.)
* Display ON/OFF.
z
z
We recommend that you take some test shots to get accustomed to the camera before you actually start.
We cannot bear any responsibility for an inability to record or replay material normally, in the event of a problem wit
this camera.
z
z
Store backups of important video clips in eg. your personal computer. We cannot bear any responsibility for any los
or alteration to the images stored in the camera’s internal or external memory.
It is prohibited to use video clips taken with this camera for commercial purposes without the consent of the copyrig
owner.
z
z
Do not turn the Normal /Macro switch dial unnecessarily. It may become malfunction.
Please take note not to touch the lens when turning the dial.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
PLAY / ERASE MODE
This mode allows you to replay/erase images/video clips stored in the camera’s internal or card memory on the LCD
monitor.
Play Basics:
1. Turn on the camera.
2. Select the Play/Erase mode with the [MODE] button.
3. The latest captured image (or the starting scene of the latest captured video clip) will be displayed on the LCD
monitor. As you press the [DISPLAY]/ Up
button, the LCD screen changes as follows:
Still Image:
Image Info. OFF
Thumbnail
display
Image Info. ON
[DISPLAY]/Up
[DISPLAY]/Up
button pressed
button pressed
Video Clip:
Thumbnail display
[DISPLAY]/ Up button pressed
Image Info. ON
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press the
/
buttons to go to the next or previous image/video clip.
5. For video clips only: press the shutter button to play. Press the same button to pause/resume. And press the
[OK/ZOOM] button to stop playing.
Thumbnail display function.
During the Play/Erase mode, the captured still images/video clips will be displayed on the LCD monitor. Toggle the
[DISPLAY]/Up
buttons. Upon pressing the [OK/ZOOM] button, the chosen image/video clip will be displayed on the LCD screen
in full size.
button until the thumbnail screen appears. The user can select a thumbnail image using the
/
/
/
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
MENU SETTINGS
Pressing the [MENU] button in the various mode will display the respective MENU on the LCD monitor:
Using the menus, you can perform various settings for your camera.
Procedures:
1. Use the
/
buttons to highlight the desired item.
2. The setting of the item with options displayed at the bottom of the screen can be change by pressing
for setting of the other items, press [OK/ZOOM] button to proceed.
/
button. As
3. Press [MENU] button to return to the previous screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
“SETUP MENU” (
,
,
)
“LCD BRIGHTNESS”
Adjusts the brightness of the LCD monitor.
Setting value: [-5] to [+5] (Interval = 1)
Default = [0]
“DATE/TIME”
Sets the Date and Time information. When a shot is taken, the date and time of the shot will be recorded on the image
file.
To set the date and time:
1. Go into the “SETUP” menu, select the “DATE/TIME” item and press [OK/ZOOM] button.
2. The screen shown below will appear on the LCD monitor.
3. Use the
/
button to select the desired segment and then use the
/
buttons to correct the setting.
The time setting can be change in steps of 1 minute by the
/
button, by pressing and holding the
/
button for
more than 5 seconds it can be change in steps of 30 minutes. This is convenient when there is a significant change in
value for time setting.
4. When all settings are complete, return to the MENU screen by pressing the [OK/ZOOM] button.
Note:
z
Please be sure to correct the date and time setting after battery replacement. To accurately display the date and time
information on the LCD monitor, you may need to correct the setting each time you turn on the camera.
“LANGUAGE”
Sets the display OSD language on the LCD monitor.
The following languages can be selected.
: English
: Dutch
Download from Www.Somanuals.com. All Manuals Search And Download.
: Swedish
: French
: German
: Spanish
: Portuguese
: Italian
“SOUND”
Enables or disables the sound function.
: Sounds each time the camera is operated.
“ON”
“OFF” : Does not sound when the camera is operated.
“FORMAT MEDIA”
This function prepares the memory (internal/external) for use by the camera. When a memory card is inserted, the card
will be formatted; In the absence of the memory card, the internal memory will be formatted.
Caution: Formatting will erase all images currently recorded in the memory card.
“FORMAT” : Formats the memory card, erasing all images in the process.
“CANCEL” : Cancels the format action.
“FILE NO. MEMORY”
With this setting set to “ON”, the file NO. does not reset even if the file in the memory has been deleted, the number of the
next recorded file will run in sequence with the deleted file number. The number runs until DSC_9999, after which it will be
set to DSC_0001.
With this setting “ON”, the recorded file will not overwrite the previously copied file in the same directory when copying
into the PC, thus preventing any accidental deletion.
“ON”
: Record the lost file number.
“OFF”
: Reset file number to DSC_0001.
“AUTO POWER OFF”
This will automatically turn off the camera after the lapse of a certain time interval (set by the user) during which no
operation is performed.
“1 min”
“3 min”
“5 min”
: Power will be turned off after 1 minute.
: Power will be turned off after 3 minutes. (Default)
: Power will be turned off after 5 minutes.
“10 min” : Power will be turned off after 10 minutes
“OFF”
: Disables the “AUTO POWER OFF” function.
“LIGHT FREQUENCY”
Through this setting, you are able to avoid image flicker due to the fluorescent light.
“50Hz” : Use this if the light frequency of the fluorescent lamp you are using is 50 Hz.
“60Hz” : Use this if the light frequency of the fluorescent lamp you are using is 60 Hz.
“FACTORY SETUP”
Performing this setting restores all settings except “DATE/TIME” to Default. Moreover, recorded files etc. cannot be
deleted.
“SETUP”
“CANCEL”
: Restore all parameters to the default setting.
: Cancel the operation.
Note:
z
The settings for “DATE/TIME”, “AUTO POWER OFF”, “LANGUAGE”, “SOUND”, “LIGHT FREQUENCY” and “FILE
NO. MEMORY” are retained even after the camera is turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
“QUICK VIEW” (
)
This feature allows you to view your images on the LCD monitor as soon as they have been taken. After the preview, this
camera will return to the Camera mode.
“ON”
: Enables “QUICK VIEW”
: Disables “QUICK VIEW”
“OFF”
The “QUICK VIEW” setting will be retained even after the camera is turned off.
Note:
z
With “QUICK VIEW” set to “ON”, the time interval before the next possible shooting will be prolong after the current
shooting.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
“EV & WHITE BALANCE” (
,
)
This screen can be alter by both EV compensation and White Balance.
The altered result reflects the taken images in real time, thereby enabling changing of the setting while confirming the
images.
EV Compensation
When the object is too dark or too bright, the camera adjusts the brightness to make the object look brighter or darker.
This is called EV compensation. The range of the exposure compensation that the user can set is from -2.0 EV to +2.0 EV
at 0.5 EV steps.
White Balance
As the intensity of the light changes, our eyes adapt such that white objects will remain white. Digital cameras can also
see the white objects as being white by averaging out the light around the object.
You may select from the following settings:
“AUTO”
: Automatically adjusts the WHITE BALANCE
: Tungsten lighting
“TUNGSTEN”
“FLUORESCENT”
“SHADE”
: Fluorescent lighting
: Overcast, shaded, twilight or evening skies
: Outdoors on a bright day
“DAYLIGHT”
After completing the setting, press [OK/ZOOM] button to end the setting.
The changed setting value, except the default value (EV: 0, White Balance: “AUTO”), will be displayed on the LCD
monitor as in the following figure.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
“SLIDE SHOW” (
)
After selecting “SLIDE SHOW” and set the delay time (with the
/
buttons) and pressing the [OK/ZOOM] button will
start the slide show. Images hitherto captured will be displayed in sequence, at intervals of the user-set delay time [1, 3, 5,
7, 9 “sec”]. To interrupt the slide show, press the [OK/ZOOM] button.
The delay time setting will be retained even after the camera is turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
“ERASE” (
)
There are two ways to erase still images/video clips:
1. “ERASE ONE”
This will allow you to erase one image/video clip at a time. Use the
clip to be erased.
/
buttons to choose the desired still image/video
A confirmation message “ERASE CURRENT?” will appear on the LCD monitor. Pressing the [OK/ZOOM] button will
cause the selected still image/video clip to be erased from memory. To abort this action, press the [MENU] button.
2. “ERASE ALL”
This will allow you to erase ALL recorded still images/video clips in the memory at once. Use the
the “YES” or “NO” option and then press the [OK/ZOOM] button to confirm.
/
buttons to choose
Note:
If no still image/video clip is stored in the memory, a message “NO IMAGE” appears on the LCD monitor.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
“COPY TO CARD” (
)
This function allows you to copy all captured still images/video clips from the internal memory to the external memory
card.
“COPY” : Copies all captured still images/video clips from the internal memory to the external memory card.
If a card has not been inserted in the camera, the message “NO CARD” will be displayed on the LCD
monitor.
“CANCEL”: Cancel the operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
“DPOF” (Digital Print Order Format) (
)
“DPOF” enables you to print the images directly from “DPOF” compatible printers by simply inserting the memory card
into the printer after performing the necessary settings.
“ONE BY ONE”
:Perform setting to each image one at a time. The following screen will appear, when “ONE BY
ONE” is selected and confirmed by pressing the [OK/ZOOM] button.
Select the images by
/
button, and set the print quantity [0 - 9] by
/
button. Printing cannot
be performed if the setting is [0]. The default value is [0]. After completing all image setting, press
[OK/ZOOM] button to confirm and return to the Menu screen.
“ALL 1 PCS”
:Sets the print quantity of all the images in the memory to 1 PCS, convenient for printing all the
captured images one at a time.
Select “ALL 1 PCS” and execute by pressing the [OK/ZOOM] button.
“DELETE ALL”
:Deletes all the “DPOF” setting being set.
Select “DELETE ALL” and delete by pressing the [OK/ZOOM] button.
Note:
z
“DPOF” setting is not possible in Video Clip.
The “DPOF” settings are retained even after the camera is turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
TRANSFERRING IMAGE DATA TO THE COMPUTER
Before image data transfer, you need to connect the camera to your computer with the supplied USB cable and Windows
98/98SE users need to install the camera drivers included in the supplied CD-ROM.
Once the camera is connected to the PC, power will be supplied to the camera through the USB cable.
System Requirements
Before installing the Camera Driver and Application software, make sure your system meets the following system
requirements:
z
z
z
z
z
z
z
Microsoft® Windows® 98/98SE/Me/2000/XP (Pre-installed Model)
Intel® Pentium® Processor 166 MHz or higher
Free USB Port
Minimum RAM: 32 MB (Windows XP: 128 MB)
250 MB of available hard disk space
Color display: 800x600 or better
CD-ROM drive
Note:
z
Please connect the camera directly to the PC. Camera performance is not guaranteed in the case that the camera is
connected to the PC via a USB Hub.
Connecting the Camera to Your Computer
For Windows 98/98SE users, it is necessary to install the Mass Storage Driver contained in the supplied CD-ROM before
connecting the camera to the PC for image data download. For Windows Me/2000/XP users however, this is not
necessary. (Proceed to connect the camera to the PC)
Installation Procedures:
1. Place the supplied CD-ROM into the CD-ROM drive.
2. A Setup Menu screen will appear on the PC monitor as shown below. Click on “USB Mass Storage Driver install for
Windows 98/98SE”.
3. Follow the on-screen instructions to complete the installation.
4. Reboot your computer.
Once you have installed the appropriate Camera Driver(Windows 98/98SE), you are now ready to connect the
camera to the PC for download. Follow the procedures below:
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedures:
1. Turn off the camera.
2. Open the USB port cover. Plug the smaller connector of the USB cable into your camera’s USB port.
3. Plug the other end of the USB cable to your computer's USB port.
4. The camera powers ON automatically, and the “USB MODE” screen appears on the LCD monitor as follows:
Select “DISK DRIVE” and press the [OK/ZOOM] button.
5. Your computer will recognize the camera as a newfound hardware. Setup for this new hardware will proceed
automatically. This Setup process is performed only once and will not be necessary for subsequent connections.
When complete, your camera will be indicated as a “Removable Disk” in your computer’s “My Computer” folder.
Download from Www.Somanuals.com. All Manuals Search And Download.
(This screen is from Windows XP)
Note:
For Windows XP, the computer will display a message screen as below.
In this case, please click on “Open folder to view files” and proceed by clicking the “OK” button.
(This screen is from Windows XP)
Downloading Pictures
1. Click on the “My Computer” icon on your PC screen. You will then see a drive icon labeled “Removable Disk”.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Double click on “Removable Disk”. A new window with a “DCIM” folder icon opens.
(This screen is from Windows XP)
* If this icon is not displayed, your camera has not been properly connected to the computer. In this case, go to
“Connecting the Camera to Your Computer” and repeat the procedures.
3. Double click on the “DCIM” folder icon. A new window with a “***JVCGC” folder icon opens (***represents a number in
the range of 100~999). Your recorded images will be in this folder.
Download from Www.Somanuals.com. All Manuals Search And Download.
(This screen is from Windows XP)
4. You can then copy the whole folder or specific files in the folder (double click on the icon to reveal the files) into your
computer’s hard drive, or any other storage media available in your PC system. Just select the folder or files and use
the usual “cut” and “paste” functions available in the “Edit” menu.
(This screen is from Windows XP)
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
z
While the camera is connected to your computer, the camera will not allow you to capture images. You will also not be
able to view the images on the camera’s LCD monitor.
z
Please refer to your computer’s instruction manual to ascertain the procedures for copying and shifting of files.
Using the Camera as a USB PC Camera
This camera can also act as a video camera for your PC, allowing you to hold videoconferences over the internet or
corporate intranet.
Before you start, you will have to install the WebCam Driver into your computer, regardless of your PC’s OS version
(Windows 98/98SE/Me/2000/XP).
To install the WebCam Driver:
1. Place the supplied CD-ROM into the CD-ROM drive.
2. A Setup Menu screen will appear on the PC monitor as shown below. Click on “Webcam Driver Install”.
3. Follow the on-screen instructions to complete the installation.
4. Reboot your computer.
Using your camera as a USB PC camera with Microsoft Netmeeting or Windows Messenger:
1. Make sure you have installed the WebCam Driver.
2. Make sure that your camera is turned off. Then, connect the USB cable to the camera and your computer’s USB port.
The camera powers ON automatically.
3. The “USB MODE” screen appears on the LCD monitor as follows:
Select “PC CAMERA” and press the [OK/ZOOM] button.
4. Your computer will recognize the camera as a newfound hardware and Setup will proceed automatically. This Setup
process is performed only once and will not be necessary for subsequent connections.
Note:
For Windows XP, the computer will display the warning screen as below several times when recognizing the camera.
In this case, please click the “Continue Anyway” button.
Download from Www.Somanuals.com. All Manuals Search And Download.
(This screen is from Windows XP)
The setup menu and message used for the explanation are in English. Please be aware that different message will
appear if other language is selected during software installation.
5. Launch the PC Camera Application software (Microsoft Netmeeting/Windows Messenger) and follow the instructions
displayed on the computer monitor.
6. Start video conferencing.
7. After the video conference, be sure to switch off the computer first before disconnecting the camera from it.
Notes:
z
The PC camera Application software is not included in the CD-ROM. Use a commercially available videoconferencing
software such as the above mentioned Microsoft Netmeeting or Windows Messenger. For more information about
video conferencing software, please refer to the respective software’s help functions.
z
z
To videoconference over the Internet or LAN, you would also need networking devices such as modems, speakers
and microphones.
The other party you wish to videoconference with must also have Microsoft Netmeeting/Windows Messenger running
in order to start the videoconference.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back] [Next]
TROUBLESHOOTING
When the camera does not work:
Possible cause
Rectifications
Power unintentionally cut off.
Press the [POWER] button to turn the camera on.
Power cut off due to camera's Automatic Power Press the [POWER] button to turn the camera on.
Off feature.
Battery direction is wrong.
The batteries are weak.
Rearrange the batteries in the correct position.
Replace batteries.
Battery performance deterioration due to low
temperature.
Warm up the batteries to some extent by, for example, rubbing them
against a soft surface before use.
Camera is connected to PC. (When connected Detach the camera from the PC after image-data download.
to PC, the camera will not be able to shoot).
Condensation inside camera.
Dry the camera before turning on the power.
When the flash does not work:
Possible cause
Rectifications
Camera is set at the Video Clip or Play mode. Set camera to Camera mode.
Flash is set to off.
Set to Auto/Red-eye.
Shooting in bright light situation.
The flash does not fire in bright light situation.
When the LCD Monitor does not show well:
Possible Cause
Rectifications
The camera is held under bright sunlight.
Use your hand to cover the monitor from sunlight. Alternatively, use the
viewfinder.
The LCD monitor is not activated.
Press the [DISPLAY]/Up
button to activate the monitor.
When you are unable to shoot:
Possible Cause
Rectifications
Power is low or off.
Check battery level. Replace if necessary.
Flash re-charge after shooting is not yet
complete.
Release the shutter button, wait till the Status Indicator is unlit, then
shoot again.
Internal or card memory full.
Erase the images no longer required, transfer them to your PC or insert
a new memory card.
The card is write protected.
Use a new card or disable the write protection.
(only for SD card)
When you are unable to replay the images:
Possible Cause
Rectifications
Check battery level. Replace if necessary.
Set camera to Play mode.
Power is low or off.
Camera is set to the wrong mode.
The pictures have not been saved in memory. Follow the instructions in this manual, shoot again and replay.
When you are unable to Format or Erase:
Possible Cause
The card is write protected.
Rectifications
Disable the write protection. (only for SD card)
When photographs turn out too bright:
Download from Www.Somanuals.com. All Manuals Search And Download.
Possible Cause
The subject was too bright.
Rectifications
Adjust the exposure or change the angle of shot.
When photographs turn out too dark:
Possible Cause
Rectifications
The flash was obstructed by fingers or other
objects.
Adjust the angle of shot and remove obstructive objects.
The subject was too far from the camera for the Move closer to the subject. Alternatively, turn off the flash and use a
flash to be effective.
tripod stand.
Flash is set to off.
Set to Auto/Red-eye.
When the color of the Images appear odd:
Possible Cause
Rectifications
No white area on the subject.
Introduce a white item or set the White Balance according to the lighting
condition.
White Balance setting incorrect.
Set the White Balance according to the lighting condition.
When parts of the images are missing:
Possible Cause
Rectifications
The lens is partially covered by fingers or the
strap.
Remove obstructing fingers or strap from lens.
Shooting distance too close.
Use the LCD monitor and the zoom function.
When the image is out of focus:
Possible Cause
Rectifications
Camera movement during still image capture. Press the shutter button down steadily.
The lens is dirty.
Use a lens blower (sold in the market) to rid the lens of dust. Then wipe
with lens cleaning paper.
Photographer was standing in front of the
Do not stand in front of the camera. Press the shutter button while
camera when pressing the shutter button (Self- looking through the viewfinder.
Timer shots).
Flash is off even when the lighting condition is Either use a tripod stand, or use the flash.
poor. As exposure time is prolonged, camera
movement will cause the image to be off focus.
The subject is too near.
Shoot at a distance of more than 1.9 m.
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back]
CAMERA SPECIFICATIONS
Image Sensor
2.0 Megapixels CMOS
10-bit Color (RGB)
Color
Image Resolution & Quality
Camera mode:
1600x1200 pixels Fine quality
1600x1200 pixels Normal quality
1280x960 pixels
640x480 pixels
Video Clip mode:
320x240 pixels
Memory
Internal: 8 MB
External: SD or Multimedia Card
File Format
JPEG (EXIF 2.1), DPOF, AVI (Motion-JPEG)
Camera mode:
Number of storage (Initial
Estimated Storage with 8MB
internal memory)
1600x1200 pixels Fine quality
1600x1200 pixels Normal quality
1280x960 pixels
(Approx. 10 pcs)
(Approx. 20 pcs)
(Approx. 40 pcs)
(Approx. 80 pcs)
640x480 pixels
Video Clip mode:
320x240 pixels
(Approx. 46 sec)
z
z
The number of recordable images also varies with the subject and the capacity
of the memory card.
The number of remaining images that can be recorded, shown on the LCD
monitor, will decrease by 1 every time you take a new shot. If, however, the file
size is too minimal, the number will remain the same after the shot is taken. By
the same token, the number will decrease by more than 1 if the file size is too
large.
USB Frame Rate (WebCam)
Recording Media
Lens
320x240 (USB1.1)
SD or Multimedia card
Fixed focus (2x, 3x, 4x digital zoom), F 2.8
f = 9.96 mm (equivalent to 51.3 mm on a 35-mm still camera)
Focus Range
Normal: 1.9 m ~ infinity, Macro: 40 cm ~ 50 cm
1/15 ~ 1/1000 seconds
Shutter Speed
Exposure Control
Auto
Manual: 0.5 EV step, -2.0 ~ +2.0
White Balance
Flash
Auto / Sun / Shade / Fluorescent / Tungsten
Built-In: Auto, Flash Off, Red-eye reduction
10 seconds delay, 2 seconds delay
Self-Timer
Software
MGI Photo Suite IV SE and Photo Vista 2.02
Language
English, French, Spanish, Traditional Chinese, German, Dutch, Swedish,
Portuguese, Italian
LCD monitor
Connectors
Weight
1.5" color TFT LCD
USB port (Mini B type)
About 110 g (without battery and SD card)
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimension
Approx. 82 mm x 60 mm x 30.5 mm
[3.2 inches (W) x 2.4 inches (H) x 1.2 inches (D)]
* Design and Specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|