JVC DVD VCR Combo HR XV48EK User Manual

DVD PLAYER &

VIDEO CASSETTE RECORDER

HR-XV48EK

INSTRUCTIONS

LPT0991-001A

Download from Www.Somanuals.com. All Manuals Search And Download.

When the equipment is installed in a cabinet or a shelf, make

sure that it has sufficient space on all sides to allow for ventilation

(10 cm or more on both sides, on top and at the rear.)

Some Do’s And Don’ts On

The Safe Use Of Equipment

When discarding batteries, environmental problems must be

considered and the local rules or laws governing the disposal of

these batteries must be followed strictly.

This equipment has been designed and manufactured to

meet international safety standards but, like any

electrical equipment, care must be taken if you are to

obtain the best results and safety is to be assured.

Failure to heed the following precautions may result in

damage to the unit, remote control or video cassette.

1. DO NOT place the unit —

DO read the operating instructions before you attempt to

use the equipment.

— in an environment prone to extreme temperatures or

humidity.

DO ensure that all electrical connections (including the

mains plug, extension leads and interconnections

between pieces of equipment) are properly made

and in accordance with the manufacturer’s

instructions. Switch off and withdraw the mains plug

when making or changing connections.

— in direct sunlight.

— in a dusty environment.

— in an environment where strong magnetic fields are

generated.

— on a surface that is unstable or subject to vibration.

2. DO NOT block the unit’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a

newspaper or cloth, etc., the heat may not be able to get out.)

3. DO NOT place heavy objects on the unit or remote control.

4. DO NOT place anything which might spill on top of the unit

or remote control.

DO consult your dealer if you are ever in doubt about

the installation, operation or safety of your

equipment.

DO be careful with glass panels or doors on equipment.

(If water or liquid is allowed to enter this equipment, fire or

electric shock may be caused.)

5. DO NOT expose the apparatus to dripping or splashing.

6. DO NOT use this equipment in a bathroom or places with

water. Also DO NOT place any containers filled with water or

liquids (such as cosmetics or medicines, flower vases, potted

plants, cups, etc.) on top of this unit.

7. DO NOT place any naked flame sources, such as lighted

candles, on the apparatus.

8. AVOID violent shocks to the unit during transport.

DON’T continue to operate the equipment if you are in

any doubt about it working normally, or if it is

damaged in any way — switch off, withdraw the

mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose

dangerous voltages.

DON’T leave equipment switched on when it is

unattended unless it is specifically stated that it

is designed for unattended operation or has a

standby mode. Switch off using the switch on

the equipment and make sure that your family

knows how to do this. Special arrangements may

need to be made for infirm or handicapped

people.

DON’T use equipment such as personal stereos or radios

so that you are distracted from the requirements

of road safety. It is illegal to watch television

whilst driving.

DON’T listen to headphones at high volume, as such use

can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for

example with curtains or soft furnishings.

Overheating will cause damage and shorten the

life of the equipment.

DON’T use makeshift stands and NEVER fix legs with

wood screws — to ensure complete safety

always fit the manufacturer’s approved stand or

legs with the fixings provided according to the

instructions.

MOISTURE CONDENSATION

Moisture in the air will condense on the unit when you move it

from a cold place to a warm place, or under extremely humid

conditions—just as water droplets form on the surface of a glass

filled with cold liquid. Moisture condensation on the head drum

will cause damage to the tape. In conditions where condensation

may occur, keep the unit turned on for a few hours to let the

moisture dry.

ATTENTION

To mobile phone users:

Using a mobile phone in the vicinity of the unit may cause

picture vibration on the TV screen or change the screen to a

blue back display.

On placing the unit:

Some TVs or other appliances generate strong magnetic fields.

Do not place such appliances on top of the unit as it may cause

picture disturbance.

DON’T allow electrical equipment to be exposed to rain

or moisture.

ABOVE ALL...

— NEVER let anyone especially children push

anything into holes, slots or any other opening in

the case — this could result in a fatal electrical

shock;

— NEVER guess or take chances with electrical

equipment of any kind — it is better to be safe

than sorry!

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

SAFETY FIRST

EDITING (VHS DECK)

Safety Precautions ............................................... 2

Some Do’s And Don’ts On The Safe Use Of

Equipment ........................................................ 3

Editing from a Camcorder ..................................44

Editing to or from Another Video Recorder ........45

Dubbing (from DVD to VHS) .............................46

DISC INFORMATION

EDITING (DVD DECK)

About Discs ......................................................... 5

Digital Audio Dubbing ......................................47

INDEX

REMOTE CONTROL

Remote Control Functions .................................48

INSTALLING YOUR NEW UNIT

SYSTEM CONNECTIONS

Check Contents ................................................. 10

Basic Connections ............................................. 11

Connecting to a Satellite Receiver .....................50

Connecting to a Dolby Digital Decoder or an Ampli-

fier with a Built-In DTS (DVD deck only) ........51

INITIAL SETTINGS

Auto Set Up ....................................................... 12

Preset Download ............................................... 13

Initial Set Up for DVD Deck .............................. 15

Language ........................................................... 16

SUBSIDIARY SETTINGS

Mode Set (VHS deck) .........................................52

Mode Set (DVD deck) ........................................55

Tuner Set ...........................................................59

Video Channel Set .............................................64

Clock Set ...........................................................65

Child Lock .........................................................66

OPERATIONS ON VHS DECK

Basic Playback .................................................. 18

Playback Features .............................................. 19

Basic Recording ................................................ 21

Recording Features ............................................ 22

B.E.S.T. Picture System ...................................... 23

VIDEO Plus+^®Timer Programming ................... 24

Express Timer Programming .............................. 26

Automatic Satellite Programme Recording ......... 28

TROUBLESHOOTING

SPECIFICATIONS

LIST OF TERMS

OPERATIONS ON DVD DECK

Basic Playback .................................................. 30

Playback Features .............................................. 31

Using the On-Screen Bar ................................... 38

Audio/Video Files Playback ............................... 40

Download from Www.Somanuals.com. All Manuals Search And Download.

DISC INFORMATION

Region Number

About Discs

The world is divided into 6 regions for DVD VIDEO discs. DVD

VIDEO discs are assigned a region number to indicate which

region they may be played back in. A disc cannot be played

back on this unit unless the region number of the disc matches

that of the unit. The region number for this unit is “2.” Only discs

whose region number includes “2” can be played back such as

shown below.

Playable Discs

You can use discs with the following logos for playback only.

DVD VIDEO

Video CD/Super Video CD

Examples of DVD VIDEO labels which can be played back using

this unit.

Audio CD

2 3

4 5

1 2 3

4 5 6

ALL

2 5

CD-DA files

DVD VIDEO Marks

● The following discs also can be played back.

• DVD-R/-RW discs recorded in DVD VIDEO format and

finalized.

• CD-R/RW discs recorded in Video CD, SVCD (Super Video

CD), or Audio CD format and finalized.

• The DivX file on the DVD-R and DVD-RW discs written in

the UDF format.

• CD-R/RW discs written in MP3/JPEG/DivX in accordance

with the “ISO 9660” format. (See page 40 for details.)

● This unit can also play back audio signals recorded in MIX-

MODE CD, CD-G, CD-EXTRA, and CD TEXT.

● The image may be sometimes poor or noisy due to defects in

the disc itself.

Sometimes marks are printed on a DVD disc and/or on its

packaging to indicate information regarding the contents and

functions of a disc. Check marks indicating the contents and

functions of a disc. Note, however, that in some cases a disc may

not include a mark even for a function it supports.

Marks related to video

Number of subtitles

Number of angles

Recorded under the

standard 4:3 aspect

ratio

Screen includes black

bands at top and

bottom of image

which has a standard

4:3 aspect ratio (letter

box)

● With some discs, operations may not be possible.

Marks of discs in this instruction manual

Allows operation with a

DVD VIDEO disc.

Allows operation with a

Video CD disc.

Video playback is in Wide video mode (16:9) on

wide televisions, but in letter box on televisions

with standard 4:3 aspect ratio.

Allows operation with a

SVCD disc.

Allows operation with

an Audio CD disc.

Video playback is in Wide video mode (16:9) on

wide televisions, but pan and scan is used on

televisions with standard 4:3 aspect ratio (either

the left or right side of the image is cut-out).

Unplayable Discs

The following types of discs cannot be played using this unit.

● CD-ROM discs (including PHOTO-CD)

● DVD AUDIO discs

● Super Audio CDs (SACD)

● DVD-RW discs recorded in VR format

● DVD-RAM discs

● DVD-ROM discs

Marks related to audio

Number of audio tracks

In addition, this unit does not play:

● Unfinalized discs

Dolby Digital mark

● Discs of irregular shape or discs with tape, seals, or paste on

either the label side or playback side. Playing back these discs

may damage the unit.

Dolby Laboratories has developed a digital

surround system for the home. This mark

indicates that you may enjoy 5.1-channel

audio (front left and right, center, rear left and

right, and a channel for LFE (Low-Frequency

Effects)).

DTS (Digital Theater System)

You can enjoy DTS audio if you connect an

amplifier with a built-in DTS decoder to the

DIGITAL AUDIO OUT connector of the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

DISC INFORMATION (cont.)

File Structure of Discs

Care and Handling of Discs

DVD VIDEO

How to handle discs

Typically, DVD VIDEO discs are made up of larger units called

“titles.” Each title has a number (title number) that can be used to

select desired titles. Titles are further divided into units called

“chapters.” Each chapter has a number (chapter number) that

can also be used to select desired chapters. Note that some discs

are not divided into titles and chapters.

When handling a disc, do not

touch the surface of the disc.

Since discs are made of

plastic, they are easily

damaged. If a disc gets dirty,

dusty, scratched or warped,

the images and sound will not

be picked up correctly, and such a disc may cause the unit to

malfunction.

Title1

Title2

Chapter 2

Chapter 3

Chapter 1

Chapter 2

Label side

Do not damage the label side, stick paper to or use any adhesive

on its surface.

Storage

Audio CD/Video CD

Make sure that discs are kept in their cases. If discs are piled on

top of one another without their protective cases, they can be

damaged. Do not put discs in a location where they may be

exposed to direct sunlight, or in a place where the humidity or

temperature is high. Avoid leaving discs in your car!

Typically, Audio CD discs are divided into separate tracks each

containing one song. Each track is assigned a number. For

example, the third track is Track 3. The same is true for Video

CD discs.

Track 1

Track 2

Track 3

Track 4

Maintenance of discs

If there are fingerprints or other dirt

adhering to a disc, wipe with a soft dry

cloth, moving from the center outwards.

If a disc is difficult to clean, wipe with a

cloth moistened with water. Never use

record cleaners, petrol, alcohol or any

anti-static agents.

NOTE:

Video CD discs that support Playback Control (PBC)

The still image or motion image which follows a menu screen is

called a “scene.” Each scene has a scene number.

For more details, refer to “Locating a Desired Scene Using the

Menu of a Video CD/SVCD with Playback Control (PBC)

Function” (੬ pg. 31).

CAUTION

Sometimes during playback, noise or images may be garbled.

This is sometimes due to the disc. (It may not be up to

industry standards.)

Placing a Disc

1 Open the disc tray.

These symptoms are caused by the discs, not by the

malfunction of the unit.

Press x on the DVD deck to open the disc tray.

● The unit’s power comes on

automatically.

● Do not block the disc tray with

your hand while it is opening or

closing as this may result in

hardware failure.

● Do not place unplayable discs or

any object other than a disc in

the disc tray.

● Do not press down strongly on the disc tray or place any heavy

objects on it.

2 Place the disc.

Place the disc in the disc tray with

the label side facing up.

● Since disc size changes depending on

the disc to be played back, be sure to

correctly align the disc with the

grooves for its size. If the disc is not in

its groove, it may be scratched or

otherwise damaged.

● To insert an 8 cm disc, place it according to the inner groove.

3 Press x on the DVD deck to close the disc tray.

● Pressing 4 also closes the disc tray.

● Playback begins automatically if an auto-playback DVD disc is

loaded. Although the VHS deck is selected, the DVD deck is

selected automatically (except when the VHS deck is in the

timer mode or the Automatic Satellite Programme Recording

mode.)

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX

Front View

G H I

N O P Q R

A STANDBY/ON Button (1) ੬ pg. 12, 18, 40

B VCR Indicator ੬ pg. 18, 21

N Record Button (7) ੬ pg. 21, 22

O Rewind Button (3) ੬ pg. 18, 19, 32

P Fast Forward Button (5) ੬ pg. 18, 19, 32

Q Programme Button (PR +/–) ੬ pg. 21

R Automatic Satellite Programming Button (SAT#)

੬ pg. 28

C Cassette Loading Slot ੬ pg. 18

D VCR/DVD Button ੬ pg. 18, 21, 30, 40

E Disc Tray ੬ pg. 30

F DVD Indicator ੬ pg. 30

G Stop Button (8) ੬ pg. 18, 21, 30, 41, 48

H Play Button (4) ੬ pg. 18, 21, 30, 41, 48

I DVD Open/Close Button (x) ੬ pg. 30, 41

J Cassette Eject Button (x) ੬ pg. 18, 21

K Video/Audio Input Connectors (VIDEO/AUDIO)

੬ pg. 44

To access covered

connectors or buttons, pull

and open the cover.

L Infrared Beam Receiving Window

M Front Display Panel ੬ pg. 8

Rear View

DVD

A Region Number Label ੬ pg. 5

B Mains Power Cord ੬ pg. 11

F Digital Audio Output Connector

(DIGITAL AUDIO OUT) ੬ pg. 47, 51

G L-2 Input/Decoder Connector

(L-2 IN/DECODER) ੬ pg. 45, 50

C L-1 Input/Output Connector (L-1 IN/OUT) ੬ pg. 11,

45, 50

D Audio Output Connectors (AUDIO OUT (L/R))

H Remote Pause Connector (PAUSE) ੬ pg. 44

Antenna Output Connector (ANTENNA OUT)

pg. 11, 50

E Antenna Input Connector (ANTENNA IN) ੬ pg. 11,

੬

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX (cont.)

Front Display Panel

A VCR Mode Indicator ੬ pg. 21, 22

B Channel/Clock Display

C VCR Indicator ੬ pg. 22

D “Timer” Indicator ੬ pg. 25, 26, 29

Mode Display (L-1, L-2, F-1 or SAT*)

* When “L-2 SELECT” is set to “SAT” (੬ pg. 54), “SAT” appears

instead of “L-2”.

E Automatic Satellite Programme Recording Indicator

(N) ੬ pg. 29

Counter Display

Tape Speed (SP/LP) ੬ pg. 21

Multi-information window*

* The current group/title/track/chapter number(s), time and status

information.

On-Screen Display (VHS deck)

If you press – –:– – on the remote control when “O.S.D.”

is set to “ON” (੬ pg. 53), various operational indicators

appear on the TV screen.

G PDC* Indicator ੬ pg. 24, 26

* VPS (Video Programme System) recording is not currently available

in the U.K. and not possible with this unit.

H Tape Position Indicator

The tape position indicator

appears on the TV screen

when you press 3 or

5 from the Stop mode or

perform an Index Search.

(੬ pg. 19) The position of

“q” in relation to “0”

For the on-screen display for DVD deck, refer to “Using

the On-Screen Bar” (੬ pg. 38).

(beginning) or “+” (end)

shows you where you are

on the tape.

Beginning

End

NOTE:

Depending on the type of tape being used, the tape position

indicator may not appear correctly.

I Audio Mode Display ੬ pg. 20

J Tape Speed (SP/LP)

A “Cassette Loaded” Mark

K Tape Direction

B Operation Mode Indicators

L Index Mark Indicator (MARK) ੬ pg. 21

M Counter Display

N Tape Remaining Time Indicator ੬ pg. 22

C Channel Position Number and Station Name/Auxiliary

Input Indicator (L-1, L-2, F-1 or SAT*)

* When “L-2 SELECT” is set to “SAT” (੬ pg. 54), “SAT” appears

instead of “L-2.”

D Clock Display

E Current Day/Month/Year

F Type of Broadcast ੬ pg. 23

Download from Www.Somanuals.com. All Manuals Search And Download.

A TV Standby/On Button (TV 1) ੬ pg. 49

Remote Control

B TV/VCR/DVD switch ੬ pg. 13, 15, 18, 21, 30, 40, 49

C DVD Button ੬ pg. 15, 30, 40

D VCR Button ੬ pg. 15, 18, 21, 24, 26

E Number Keys

F Daily Button (DAILY) ੬ pg. 25, 27

G PDC* Button ੬ pg. 24, 26

* VPS (Video Programme System) recording is not currently available

in the U.K. and not possible with this unit.

H Reset Button (0000) ੬ pg. 22

Cancel Button (&) ੬ pg. 24, 27

I Auxiliary Button (AUX) ੬ pg. 44

J Start Time Button (START +/–) ੬ pg. 26

Repeat Button (REPEAT) ੬ pg. 33

Zooming Button (ZOOM) ੬ pg. 32

K Stop Time Button (STOP +/–) ੬ pg. 26

On Screen Button (ON SCREEN) ੬ pg. 38

L Programming Button (PROG) ੬ pg. 24, 26

M Tape Speed Button (p) ੬ pg. 21, 24, 26

Top Menu Button (TOP MENU) ੬ pg. 31

N Programme Check Button (") ੬ pg. 27

Return Button (RETURN) ੬ pg. 31

O w e Button

rt Button

ENTER Button

VCR Programme Button (VCR PR +/–)

P Set Up Menu Button (SET UP) ੬ pg. 13, 15, 52, 55

Q Play Button (4) ੬ pg. 18, 30

R Rewind Button (3) ੬ pg. 18, 19, 32

S Record Button (7) ੬ pg. 21, 22

T Forward Skip/Index Button (6) ੬ pg. 19, 31

U Reverse Skip/Index Button (2) ੬ pg. 19, 31

Review Button (

) ੬ pg. 20

V DVD Picture Button (DVD PICTURE) ੬ pg. 36

W Sound Effect Button (SOUND EFFECT) ੬ pg. 37

X Standby/On Button (1) ੬ pg. 12, 18, 40

Y TV Muting Button ( ) ੬ pg. 49

Audio Monitor Button (A.MONITOR) ੬ pg. 20, 23,

Z TV/VCR Button ੬ pg. 22

a TV Volume Button (TV % +/–) ੬ pg. 49

b Weekly Button (WEEKLY) ੬ pg. 25, 27

c TV Programme Button (TV PR +/–) ੬ pg. 49

d Programme Button (PR +/–) ੬ pg. 21, 26

e Date Button (DATE +/–) ੬ pg. 26

Subtitle Button (SUBTITLE) ੬ pg. 34

Angle Button (ANGLE) ੬ pg. 35

Buttons with a small dot on the left side of the name can also

be used to operate your JVC TV. (੬ pg. 49)

How To Use

The remote control can operate most of your unit’s functions,

as well as basic functions of TV sets of JVC. (੬ pg. 49)

● Point the remote control toward the receiving window.

● The maximum operating distance of the remote control is

about 8 m.

f Timer Button (#) ੬ pg. 25, 26, 27

g Menu Button (MENU) ੬ pg. 31

h Automatic Satellite Programming Button (REC LINK)

NOTES:

੬ pg. 28

● When inserting the batteries, be sure to insert in the correct

directions as indicated under the battery cover.

● If the remote control doesn’t work properly, remove its

batteries, wait a short time, replace the batteries and then try

again.

i Display Button (– –:– –) ੬ pg. 22

j Fast Forward Button (5) ੬ pg. 18, 19, 32

k Stop/Clear Button (8) ੬ pg. 18, 21, 30

l Pause Button (9) ੬ pg. 19, 21, 30

m One Touch Replay Button ( ) ੬ pg. 19, 32

n Skip Search Button ( ) ੬ pg. 19

o Tracking Button (TRACKING +/–) ੬ pg. 20

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING YOUR NEW UNIT

Check Contents

CHECK ALL THE CONTENTS SHOWN BELOW

DVD Player and Video Cassette Recorder

“AA” Batteries (x 2)

RF Cable

Infrared Remote Control Unit

4 You are now ready to install your unit. (੬ pg. 11)

Download from Www.Somanuals.com. All Manuals Search And Download.

It’s essential that your unit be properly connected.

Basic Connections

THESE STEPS MUST BE COMPLETED BEFORE ANY

VIDEO OPERATION CAN BE PERFORMED.

A ^{Situate the unit.}

Mains outlet

TV aerial cable

Place the unit on a stable, horizontal surface.

Mains power cord

B ^{Connect the unit to TV.}

The connection method you use depends on the type of

TV you have.

RF Connection

8To connect to a TV with NO AV input connectors —

A Disconnect the TV aerial cable from the TV.

B Connect the TV aerial cable to the ANTENNA IN

connector on the rear panel of the unit.

Back of unit

C Connect the provided RF cable between the

ANTENNA OUT connector on the rear panel of the

unit and the TV’s aerial connector.

21-pin SCART cable

(not provided)

AV Connection

8To connect to a TV with AV input connectors —

If your TV is equipped with a 21-pin SCART connector,

perform AV connection to improve picture quality during

tape playback.

A Connect the aerial, unit and TV as per “RF

Connection.”

B Connect an optional 21-pin SCART cable between the

L-1 IN/OUT connector on the rear panel of the unit

and the TV’s 21-pin SCART connector.

RF cable (provided)

C ^{Connect the unit to mains.}

Plug the end of the mains power cord into a mains outlet.

After the connection is completed, perform “Auto Set

Up” on page 12.

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SETTINGS

While Auto Set Up is in progress, do NOT press any

button on the unit or remote control until the front

display panel shows either the display as illustrated in

step C or “– –:– –” as illustrated on page 14.

Auto Set Up

Auto Channel Set/Auto Clock Set/

Auto Guide Program Number Set

● The AUTO SET screen will

appear on the TV screen. As

Auto Set Up progresses, the

“q” mark on the TV screen

moves from left to right.

After the 1 button on the unit or remote control is pressed

for the first time to power on the unit, the Auto Set Up

function sets the tuner channels, clock and Guide Program

numbers automatically.

Before starting, make sure of the following:

● The TV aerial cable should be connected to the unit.

● The unit’s mains power cord should be connected to a

mains outlet.

● The TV should be set to its AV mode (with AV connection

੬ pg. 11) or UHF channel 52 (with RF connection

੬ pg. 11).

Beginning

End

● When you have connected the unit to a TV offering T-V Link

via a fully-wired 21-pin SCART cable (੬ pg. 11) and the TV is

turned on, the unit automatically performs the Preset

Download (੬ pg. 13) even if you select “AUTO SET” for Auto

Set Up function.

● Slide the TV/VCR/DVD switch on the remote control to the

right.

Slide to the

right.

C ^{Confirm/Set video channel.}

With RF Connection

The video channel that is

blinking on the front display

panel is your video channel. Press ENTER.

● To view picture signals from the unit, set your TV to the video

channel.

With AV Connection

Press PR – until the front

display panel shows “– –.”

Now the video channel is set to off. Then press ENTER.

● To view picture signals from the unit, set your TV to its AV

mode.

ATTENTION

Once you have performed Auto Set Up, even if the unit’s

memory backup has expired, all the stored stations and their

Guide Program numbers remain in the unit’s memory and

the unit will not perform Auto Set Up again. The unit

performs only Auto Clock Set when the unit is turned on.

If you have moved to a different area, perform each setting as

required.

● Video channel setting (for RF connection users) ੬ pg. 64

● Tuner setting ੬ pg. 59

● Clock setting ੬ pg. 65

A ^{Turn on the unit.}

Press 1 on the unit or remote control.

B ^{Perform Auto Set Up.}

The AUTO SET/T-V LINK display appears on the TV

screen.

If a new station starts broadcasting in your area, perform

tuner setting (੬ pg. 59) and, if necessary, video channel

setting (੬ pg. 64).

Press rt to move the

highlight bar (pointer) to

“AUTO SET” and press

ENTER or e.

NOTES:

● In areas where no TV station transmits a PDC (Programme

Delivery Control) signal, the unit can perform neither Auto

Clock Set nor Auto Guide Program Number Set.

● If there is a power cut, or if you press 1 or SET UP while Auto

Set Up is in progress, Auto Set Up will be interrupted; be sure

to turn off the unit power once and try again from step A.

● Auto Clock Set may not function properly depending on the

reception condition.

● When selecting “AUTO SET,”

“Auto” also appears on the

front display panel.

After “Auto Set Up” is completed, perform “Initial Set

Up for DVD Deck” on page 15.

Download from Www.Somanuals.com. All Manuals Search And Download.

A ^{Turn on the unit.}

Preset Download

Press 1 on the unit or remote control.

Auto Channel Set by Downloading

from TV/Auto Clock Set/Auto Guide

Program Number Set

B ^{Perform Preset Download.}

The AUTO SET/T-V LINK display appears on the TV

screen.

If you have connected the unit to your TV via the AV connection

(੬ pg. 11), the unit will automatically perform Preset

Download instead of the Auto Set Up in step B on page 12.

After downloading, the unit sets the clock and Guide Program

numbers automatically.

Press rt to move the

highlight bar (pointer) to

“T-V LINK” and press ENTER

or e.

ATTENTION

You can use this function only with a TV offering T-V Link,

● When selecting “T-V LINK,”

“CH – –” also appears on the

front display panel.

etc.* Be sure to use a fully-wired 21-pin SCART cable.

* Compatible with TVs offering T-V Link, EasyLink, Megalogic,

SMARTLINK, Q-Link or DATA LOGIC via fully-wired 21-pin SCART

cable. The degree of compatibility and available functions may

differ by system.

Preset positions on the front display panel increase from “1”;

do NOT press any button on the unit or remote control until

the front display panel shows clock time, “1” or “– –:– –” as

illustrated on page 14.

Slide the TV/VCR/DVD switch on the remote control to the

right.

● The T-V LINK screen will

appear. Then the GUIDE

PROG SET screen will appear

during Guide Program

Slide to the

right.

Number Set. When Preset

Download is completed,

“COMPLETED” appears for

about 5 seconds, then the

normal screen appears.

● If you press any button on the

unit or remote control while

downloading is in progress, it

will be interrupted.

NOTES:

● For details, refer to the instruction manual of your TV.

● In areas where no TV station transmits a PDC (Programme

Delivery Control) signal, the unit can perform neither Auto

Clock Set nor Auto Guide Program Number Set.

● If there is a power cut, or if you press 1 or SET UP while

downloading or set up is in progress, it will be interrupted; be

sure to turn off the unit power once and try again from the

beginning.

C ^{Set the video channel.}

Set the video channel to off manually. (੬ pg. 64)

After “Preset Download” is completed, perform

“Initial Set Up for DVD Deck” on page 15.

● Auto Clock Set may not function properly depending on the

reception condition.

● On this unit, the characters available for station names (ID) are

A–Z, 0–9, –, f, + and I (space). Some names of downloaded

stations may differ from those of your TV. (੬ pg. 61)

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SETTINGS (cont.)

INFORMATION

Results of Auto Set Up/Preset

Download Appear on the Front Display

Panel

Language for the on-screen display (DVD deck)

About the on-screen language for the DVD deck, see page 15.

Just Clock

Your unit is equipped with the Just Clock function which

provides accurate time keeping through automatic adjustments

at regular intervals, by reading data from a PDC signal. If you

want to take advantage of this function, simply set it to “ON.”

(੬ pg. 65, “Just Clock”)

If both Auto Channel Set and Auto

Clock Set have been performed

successfully, the correct current time

is displayed.

Turn on the TV and select its video channel or AV mode, then

make sure that all necessary stations have been stored in the

unit’s memory by using the PR button(s).

● If station names (ID – ੬ pg. 62) have also been stored in the

unit’s memory, the station name will be displayed at the top

left corner of the TV screen for about 5 seconds when the unit

is tuned to a different station.

If you have any difficulty with the above

procedures call the JVC Customer Service Hot Line

on 0870 330 5000

● If you want to set the tuner manually such as to add or skip

channels, to change channel positions, or to set or change

station names, see pages 60 – 62.

T-V Link Functions

When you connect the unit to your TV via a fully-wired 21-pin

SCART cable (੬ pg. 11), the following functions are available.

You can use these functions only with a TV offering T-V Link,

etc.*

If Auto Channel Set has succeeded

but Auto Clock Set has not, “1”

(channel position) is displayed.

For details, refer to the instruction manual of your TV.

* Compatible with TVs offering T-V Link, EasyLink, Megalogic,

SMARTLINK, Q-Link or DATA LOGIC via fully-wired 21-pin SCART

cable. The degree of compatibility and available functions may differ by

system.

A Turn on the TV and select its video channel or AV mode, then

make sure that all necessary stations have been stored in the

unit’s memory by using the PR button(s).

● If station names (ID – ੬ pg. 62) have also been stored in the

unit’s memory, the station name will be displayed at the top

left corner of the TV screen for about 5 seconds when the unit

is tuned to a different station.

● If you want to set the tuner manually such as to add or skip

channels, to change channel positions, or to set or change

station names, see pages 60 – 62.

TV Auto Power On

The TV will turn on and be set to its AV mode automatically

whenever you play a tape.

For details, refer to the instruction manual of your TV.

Unit Auto Standby

You can use your TV’s remote control to turn off the unit.

For details, refer to the instruction manual of your TV.

B Perform “Clock Set” on page 65.

If both Auto Channel Set and Auto

Clock Set have failed, “– –:– –” is

displayed.

Direct Rec (VHS deck only)

You can easily start recording the programme that you are

watching on your TV. When you use this function, set “DIRECT

REC” to “ON.” (੬ pg. 53)

Make sure the cables are connected properly and turn off the

unit’s power once, then turn the unit’s power back on again.

Perform “Auto Set Up” on page 12 or “Preset Download” on

page 13 again.

IMPORTANT

● To check if the Guide Program numbers have been set

correctly, perform the VIDEO Plus+ Timer Programming.

(੬ pg. 24) (VHS deck only)

● In certain reception conditions, station names may not be

stored correctly, and auto Guide Program Number Set may not

work properly. If the Guide Program numbers are not set

properly when you timer-record a TV programme using the

VIDEO Plus+ system, the unit will record a TV programme of a

different station. When programming the timer using the

VIDEO Plus+ system, be sure to check the desired channel is

selected correctly. (੬ pg. 24, “VIDEO Plus+^®Timer

Programming”) (VHS deck only)

● Your unit memorizes all detected stations even if reception of

some of them is poor. You can delete those stations with an

unacceptable picture. (੬ pg. 60, “Deleting a Channel”)

Download from Www.Somanuals.com. All Manuals Search And Download.

Select the type of your monitor connected to

the unit.

Initial Set Up for DVD

Deck

Press rt to select the

desired setting, then press

ENTER.

DVD PLAYER SETUP

MONITOR TYPE

4:3LB

16:9

When you turn on the DVD deck of the unit for the first

time after you purchase, the menu screen for making the

initial settings appears on the TV screen.

AUTO

PICTURE SOURCE

SCREEN SAVER

BACKGROUND

4:3 LB

4:3 PS

STANDARD

Make the following settings.

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

● 16:9 (Wide television conversion):

Select this for a wide-screen (16:9) TV.

● 4:3 LB (Letter Box conversion):

Select this for a conventional (4:3)

TV. While viewing a wide screen

picture, the black bars appear on the

top and the bottom of the screen.

● 4:3 PS (Pan Scan conversion):

Select this for a conventional (4:3)

TV. While viewing a wide screen

picture, the black bars do not

Slide to the

right.

appear; however, the left and right

edges of the pictures will not be

shown on the screen.

Select the signal type of the digital audio

output.

Set this item correctly

according to the logo on your

amplifier or decoder.

Press rt to select the desired

setting, then press ENTER.

(If you do not connect the unit

to such a device, press ENTER

to finish the initial setting.)

DVD PLAYER SETUP

DIGITAL AUDIO OUTPUT 4:3LB

PCM ONLY

AUTO

ANALOG DOWNMIX

D.RANGE CONTROL

OUTPUT LEVEL

DOLBY DIGITAL/PCM

A ^{Turn on the unit.}

STREAM/PCM

STANDARD

Press 1.

B ^{Select the DVD deck.}

Press VCR/DVD repeatedly so that the DVD indicator

lights up.

On the unit

● PCM ONLY: Select this when connecting to an

amplifier/a decoder bearing neither Dolby Digital nor

DTS logo, or a digital recorder.

● DOLBY DIGITAL/PCM: Select this when connecting an

amplifier/a decoder bearing Dolby Digital (without

DTS) logo.

● STREAM/PCM: Select this when connecting an

amplifier/a decoder bearing both Dolby Digital and

DTS logos.

On the remote control

Press DVD so that the DVD indicator lights up.

The following message appears on the TV screen.

EXECUTE DVD PLAYER SETUP? - BASIC PICTURE/AUDIO

SETTING

YES - PRESS ENTER NO - PRESS STOP

To access the initial setting menu screen again

Press SET UP for a few seconds until the initial setting

menu screen appears.

Press ENTER to start the initial setting.

Select the on-screen language for the DVD

deck.

The DVD deck offers you the

DVD PLAYER SETUP

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ENGLISH

choice to view on-screen

messages in 3 different

languages.

ON SCREEN LANGUAGE ENGLISH

ENGLISH

FRENCH

GERMAN

Press rt to select the

desired language, then press

ENTER.

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SETTINGS (cont.)

Menu/Audio/Subtitle Language Set

(DVD deck only)

Language

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Some DVD discs contain the DVD menu display, audio,

subtitle in multiple languages. With these discs, you can

set the default language as you like.

● The procedure shows how to set “MENU LANGUAGE”

on the DVD menu screen as an example.

Slide to the

right.

A ^{Turn on the unit.}

Press 1.

B ^{Select the DVD deck.}

On the unit

Press VCR/DVD repeatedly so that the DVD indicator

lights up.

On the remote control

Press DVD so that the DVD indicator lights up.

C ^{Access the DVD Set Up menu screen.}

A Press SET UP.

LANGUAGE

B Press w e to select

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ENGLISH

“

LANGUAGE.”

ON SCREEN LANGUAGE ENGLISH

D ^{Select the mode.}

Press rt to move H to

“MENU LANGUAGE,” then

press ENTER.

LANGUAGE

MENU LANGUAGE

ENGLISH

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE ENGLISH

E ^{Select the mode setting.}

Press rt to select the desired setting, then press ENTER.

● See “Language Code List” (੬ pg. 17).

F ^{Return to the normal screen.}

Press SET UP.

NOTE:

When the selected language is not available on the disc, the

disc’s default menu language is played back.

Download from Www.Somanuals.com. All Manuals Search And Download.

Language Code List

Afar

Inupiak

Kirundi

Rumanian

Russian

Kinyarwanda

Sanskrit

Sindhi

Sangho

Serbo-Croatian

Singhalese

Slovak

Abkhazian

Afrikaans

Ameharic

Arabic

Assamese

Aymara

Azerbaijani

Bashkir

Byelorussian

Bulgarian

Bihari

Bislama

Bengali, Bangla

Tibetan

Indonesian

Icelandic

Hebrew

Yiddish

Javanese

Georgian

Kazakh

Greenlandic

Cambodian

Kannada

Korean (KOR)

Kashmiri

Kurdish

Kirghiz

Latin

Lingala

Laothian

Lithuanian

Latvian, Lettish

Malagasy

Maori

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Malay (MAY)

Maltese

Burmese

Nauru

Nepali

Dutch

Norwegian

Occitan

(Afan) Oromo

Oriya

Slovenian

Samoan

Shona

Somali

Albanian

Serbian

Siswati

Sesotho

Sundanese

Swedish

Swahili

Tamil

Breton

Catalan

Corsican

Czech

Welsh

Danish

Bhutani

Greek

Esperanto

Estonian

Basque

Persian

Finnish

Telugu

Tajik

Thai

Tigrinya

Turkmen

Tagalog

Setswana

Tonga

Turkish

Tsonga

Tatar

Fiji

Faroese

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Twi

Ukrainian

Urdu

Uzbek

Hindi

Panjabi

Polish

Pashto, Pushto

Portuguese

Quechua

Rhaeto-Romance

Vietnamese

Volapuk

Wolof

Xhosa

Yoruba

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Zulu

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK

A ^{Load a cassette.}

Basic Playback

● Turn on the TV and select the video channel (or AV

mode).

Make sure the window side is

up, the rear label side is

facing you and the arrow on

the front of the cassette is

● Slide the TV/VCR/DVD switch on the remote

control to the right.

pointed toward the unit.

● Do not apply too much

pressure when inserting.

● If the record safety tab has been removed, playback begins

automatically. Although the DVD deck is selected, the VHS

deck is selected automatically.

● The unit’s power comes on automatically and the counter is

reset to 0:00:00.

B ^{Select the VHS deck.}

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

Slide to the

right.

On the remote control

Press VCR so that the VCR indicator lights up.

C ^{Find the programme start point.}

If the tape is advanced past the start point, press 3. To

go forward, press 5.

D ^{Start playback.}

Press 4. “bESt” appears blinking on the front display

panel during automatic tracking. (੬ pg. 23)

E ^{Stop playback.}

Press 8. Then press x on the VHS deck to remove the

cassette.

Usable cassettes

● Compact VHS

camcorder

recordings can be

played on this unit.

Simply place the

recorded cassette

into a VHS Cassette

Adapter and it can be used just like any full-sized VHS

cassette.

● This video recorder is equipped with SQPB (S-VHS QUASI

PLAYBACK) that lets you watch tapes recorded in the

S-VHS format and the SP mode with regular VHS

resolution.

Clean the video heads using a dry cleaning

cassette — ECL-3F — when:

● Rough, poor picture appears while a tape is played back.

● The picture is unclear or no picture appears.

● “USE CLEANING CASSETTE” appears on the screen (only

with “O.S.D.” set to “ON”). (੬ pg. 53)

* SQPB does not deliver Super VHS resolution.

● This video recorder can record on regular VHS and Super

VHS cassettes. However, it will record regular VHS signals

only.

NOTE:

The heads get dirty in the following cases:

● in an environment prone to extreme temperature or

humidity

* S-VHS recording is not possible with this recorder.

● in a dusty environment

● flaw, dirt or mold on video tapes

● continuous usage for a long time

Download from Www.Somanuals.com. All Manuals Search And Download.

Skip Search

Playback Features

● Turn on the TV and select the video channel (or AV

mode).

During playback, press

unwanted sections.

1 to 6 times to skip over

Each press initiates a 30-second period of fast-motion

playback. Normal playback resumes automatically.

● Slide the TV/VCR/DVD switch on the remote

control to the right.

To resume normal playback during a Skip Search,

press 4.

ATTENTION

Index Search

In the search, still, slow-motion or frame-by-frame playback

mode,

Your unit automatically marks index codes at the beginning of

each recording. This function gives you quick access to any one

of 9 index codes in either direction.

● the picture will be distorted.

● the noise bars will appear.

● there may be a loss of colour.

● you cannot hear the sound.

NOTE:

Before starting, make sure the unit is in the Stop mode.

Activate Index Search.

Still Picture/Frame-By-Frame

Playback

Press 2 or 6. “2 1” or “6 1” is displayed on

the TV screen and search begins in the corresponding

direction.

● To access index codes 2

1 Pause during playback.

Current position

through 9, press 2 or

6 repeatedly until the

correct index number is

displayed.

Press 9.

● If there is vertical jitter, press PR +/– on the remote control to

correct the picture.

Example:

To locate the beginning of B

from the current position,

2 Activate frame-by-frame playback.

Press 9.

Index number

press 2 twice.

To locate the beginning of D from the current position, press

6 once.

● When the specified index code is located, playback begins

automatically.

Slow Motion

While playback is paused, press and hold 9 for 2

seconds, then release. Press 9 and release again to return

to still picture.

Next Function Memory

NOTE:

The Next Function Memory “tells” the unit what to do after

rewinding. Before continuing, make sure the unit is in the Stop

mode.

During slow motion playback, some noise may appear on the TV

screen. Press PR + or – on the remote control to eliminate the

noises.

a- For Automatic Start Of Playback

Press 3, then press 4 within 2 seconds.

b- For Automatic Power Off

Press 3, then press 1 within 2 seconds.

c- For Automatic Timer Standby

Press 3, then press # within 2 seconds.

d- For Automatic Cassette Ejection After Tape Rewind

Press 3, then press x within 2 seconds.

Variable Speed Search

During playback, press 5 for forward variable speed

search, or 3 for reverse variable speed search.

● The speed changes for each direction by pressing 3 and

5 repeatedly.

When pressing 5: +5x{+7x

When pressing 3: –1x]–5x{–7x

(Once 3 is pressed, reverse search starts in –1x normal

playback speed. After this process, each press of 3 changes

the search speed between –5x and –7x.)

One Touch Replay

Press

during playback.

NOTE:

Pressing

once moves the playback position back to about 7

The search speed changes in the same way for SP and LP mode.

seconds before the current position. You can press

times each One Touch Replay.

up to 4

To resume normal playback, press 4.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

1 Override automatic tracking.

During playback, press TRACKING + and – at the same

time.

Slide to the

right.

2 Adjust the tracking manually.

Press TRACKING +/–.

● Press TRACKING + and – at the same time again to return to

automatic tracking.

NOTE:

When a new tape is inserted, the unit enters the automatic

tracking mode automatically.

Soundtrack Selection

Your unit is capable of recording three soundtracks (HI-FI L,

HI-FI R and NORM) and will play back the one you select.

During Playback

Pressing A.MONITOR changes the soundtrack as follows:

Track

Use

On-screen display

HI FI

For Hi-Fi stereo tapes

L j h R

Instant ReView

HI FI

L j

For main audio of Bilingual tapes

Simply by pressing a single button, the unit power comes on,

rewinds, and begins playback of the last timer-recorded

programme. If you have several programmes recorded, you can

easily access any of them.

HI FI

For sub audio of Bilingual tapes

h R

NORM

For audio-dubbed tapes

HI FI

NORM

NOTE:

Before starting, make sure that the unit is off and that the Timer

mode is disengaged.

NOTES:

Activate Instant ReView.

● “HIFI L j h R” should normally be selected. In this mode,

Hi-Fi stereo tapes are played back in stereo, and the normal

audio track is played back automatically for tapes with only

normal audio.

Press

. The unit power comes on and the unit

searches for the index code indicating the start of the last

timer-recorded programme. Once it’s found, playback

begins automatically.

● For instructions on recording stereo and bilingual

programmes, refer to page 23.

● “O.S.D.” must be set to “ON” or the on-screen displays will

not appear. (੬ pg. 53)

● To watch the first of the 3 programmes, press

three

times. The unit searches and begins playback automatically.

You can access a programme as far as 9 index codes away

from the current tape position.

NTSC Playback

Repeat Playback

Your unit is equipped with NTSC circuitry that can play back

NTSC tapes.

Your unit can automatically play back the whole tape 100 times

repeatedly.

1 Load a cassette.

1 Start playback.

Insert a cassette recorded in NTSC.

Press 4.

2 Start playback.

2 Activate Repeat Playback.

Press 4.

Press 4 and hold for over 5 seconds, then release.

● The Play indicator ($) on the front display panel blinks slowly.

● After playing back a tape 100 times, the unit stops

automatically.

● “NTSC]PAL” appears on the screen for about 5 seconds.

NOTES:

● Some TVs shrink the picture vertically and place black bars at

the top and bottom of the screen. This is not a malfunction on

the part of either the unit or the TV.

3 Stop Repeat Playback.

Press 8 at any time.

● The picture may roll up and down. This can be corrected using

the V-HOLD control found on some TVs. (This cannot be

corrected if the TV does not have a V-HOLD control.)

Pressing 4, 3, 5 or 9 also stops Repeat Playback.

●

The counter and tape remaining time readings will be incorrect.

Manual Tracking

● During search, still, or frame-by-frame playback, the picture

will be distorted, and there may be a loss of colour.

● Depending on the type of TV, the top and bottom portions of

superimposed displays may be cut off during NTSC playback.

Your unit is equipped with automatic tracking

control. During playback, you can override this

and adjust the tracking manually by pressing the

TRACKING +/– buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

D ^{Set the tape speed.}

display panel or TV screen. Press p again to change

the setting while the tape speed is displayed on the TV

screen.

Basic Recording

● Turn on the TV and select the video channel (or AV

mode).

Press p. The current setting appears on the front

● Slide the TV/VCR/DVD switch on the remote

control to the right.

E ^{Start recording.}

Press and hold 7 and press 4 on the remote control, or

press 7 on the unit.

● If “O.S.D.” is set to “ON” (੬ pg. 53), “MARK” blinks on the

screen while an index code is being marked.

● When “DIRECT REC” is set to “ON” (੬ pg. 53), if you press

any button just after pressing 7 on the unit (or 7 and 4 on

the remote control), the unit may not function properly.

B.E.S.T. works at the beginning of both the first SP and the

first LP recording after inserting the cassette. (੬ pg. 23)

Slide to the

right.

If “DIRECT REC” is set to “ON,” the programme that appears

on the TV screen will be recorded. (੬ pg. 53)

F ^{Pause/Resume recording.}

Press 9. Press 4 to resume recording.

● You can select channel during the Record Pause mode.

G ^{Stop recording.}

Press 8. Then press x on the VHS deck to remove the

cassette.

Recording Resume Function

If there is a power outage during recording, Instant Timer

Recording, or timer recording (੬ pg. 22, 26), the recording

will resume automatically when power is restored to the unit

unless the unit’s memory backup has expired.

Accidental erasure

prevention

A ^{Load a cassette.}

To prevent accidental recording

on a recorded cassette, remove its

safety tab. To record on it later,

Insert a cassette with the record safety tab intact.

● The unit’s power comes on automatically and the counter is

reset to 0:00:00.

cover the hole with adhesive tape.

Record safety tab

B ^{Select the VHS deck.}

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

NOTE:

When the end of the tape is reached during recording, the unit

stops and “⅜” and “$” blink on the front display panel.

On the unit

On the remote control

Press VCR so that the VCR indicator lights up.

C ^{Choose a programme.}

Press PR +/– or the number keys to select the channel

you wish to record.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

2 Engage the ITR mode.

Press 7 again. “⅜” blinks and “0:30” appears on the

front display panel.

Recording Features

● Turn on the TV and select the video channel (or AV

mode).

3 Set the recording duration.

If you want to record for more than 30 minutes, press 7

to extend the time. Each press extends recording time by

30 minutes.

● Slide the TV/VCR/DVD switch on the remote

control to the right.

NOTES:

● You can only perform ITR using the 7 button on the unit’s

front panel.

● Still picture playback stops automatically after 5 minutes to

protect the heads.

Slide to the

right.

● When the end of the tape is reached during Instant Timer

Recording or timer recording, the unit is turned off and “⅜”

and “$” blink on the front display panel.

● During Instant Timer Recording, any other timer programmed

recording won’t start even if their start time has come. In such

a case, the timer programmed recording starts (if the end time

of the timer programmed recording is set after the end of

Instant Timer Recording) after the Instant Timer Recording

finishes.

Elapsed Recording Time Indication

1 Set the counter display.

Press – –:– – until a counter reading appears on the front

display panel.

2 Reset the counter.

Recording One Programme While

Watching Another

Press 0000 before starting recording or playback.

● The counter is reset to “0:00:00” and shows the exact elapsed

time as the tape runs. You can check the exact time of a

recording or playback.

If your unit is connected to the TV via the AV connection,

press TV/VCR. The unit’s VCR indicator and the TV

broadcast being recorded disappear. Once recording is in

progress, all you need to do is to set the channel controls

on the TV for the station you wish to view.

Tape Remaining Time

Press – –:– – until the time remaining on the tape

● The programme selected with the TV’s channel controls

appears on the TV screen, while the one selected with the

unit’s PR buttons is recorded on the tape.

appears.

● The front display panel shows the tape remaining time with “:”

blinking.

NOTE:

You can also use the DVD deck in the following cases. Before

use, be sure to turn on the unit and select the DVD deck.

● During recording

● During timer recording

● During timer standby mode

● By pressing the – –:– – button, you can change the display to

show the channel position, clock time, counter reading, and

tape remaining time.

* The channel position is not displayed during playback.

Instant Timer Recording (ITR)

NOTES:

This easy method lets you record for

from 30 minutes to 6 hours (selectable in

30-min. increments), and shuts the unit

off after recording is finished.

● When you press – –:– –, the on-screen display appears on the

TV screen for 5 seconds, then the displays other than the

counter disappears. To clear the counter display, press – –:– –.

● Depending on the type of tape being used, the tape remaining

time reading may not appear right away, or is not correct.

“– –:– –” may sometimes appear with “:” blinking, or the

display may blink on occasion.

1 Start recording.

Press 7 on the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Receiving Stereo and Bilingual

Programmes

B.E.S.T. Picture System

Your unit is equipped with a Digital stereo sound decoder

(NICAM) making reception of stereo and bilingual broadcasts

possible.

The B.E.S.T. (Biconditional Equalised Signal Tracking)

system checks the condition of the tape in use during

playback and recording, and compensates to provide the

highest-possible playback and recording pictures. You

can set “B.E.S.T.” to “ON” or “OFF” to your preference.

(੬ pg. 53)

When the channel is changed, the type of broadcast being

received will be displayed on the TV screen for a few seconds.

Type of broadcast being

On-screen display

received

Playback

Regular Monaural

NICAM Stereo

NICAM Bilingual

NICAM Monaural

(none)

The unit assesses the quality of the tape once you initiate

playback.

ST NICAM

BIL. NICAM

NICAM

● The unit adjusts the playback picture quality based on the

quality of the tape in use.

● B.E.S.T. is active during automatic tracking. “bESt” appears

blinking on the front display panel.

● To listen to a stereo programme, press A.MONITOR until

“HIFI L j h R” appears on the TV screen.

● “bESt” only appears at the beginning of automatic tracking.

Even though it doesn’t appear after that, the B.E.S.T. function is

operative.

● To listen to a bilingual programme, press A.MONITOR until

“HIFI L j” or “HIFI h R” appears on the TV screen.

● To listen to the standard (Regular Monaural) audio while

receiving a NICAM broadcast, press A.MONITOR until

“NORM” appears on the TV screen.

Recording

NOTE:

The unit assesses the quality of the tape once you initiate

recording.

“O.S.D.” must be set to “ON,” or the on-screen displays will not

appear. (੬ pg. 53)

● The unit spends approximately 7 seconds assessing the

condition of the tape, then begins recording.

To Record NICAM Stereo and Bilingual Programmes

The NICAM audio programme will be recorded on the Hi-Fi

audio track, and the standard audio programme will be recorded

on the normal audio track.

ATTENTION

Since the B.E.S.T. system works before recording actually

starts, there is a delay of approximately 7 seconds after 7

and 4 on the remote control are pressed, or 7 on the unit is

pressed. To make sure you record the desired scene or

programme in its entirety, first perform the following steps:

A Press and hold 9 and press 7 to engage the Record Pause

mode.

NOTES:

● If the quality of stereo sound being received is poor, the

broadcast will be received in monaural with better quality.

● Before playing back a programme recorded in stereo, or a

bilingual programme, refer to “Soundtrack Selection” on

page 20.

● The unit then automatically checks the condition of the

tape and, after approximately 7 seconds, re-enters Record

Pause mode.

B Press 4 to start recording.

If you want to bypass the B.E.S.T. system and begin recording

immediately, set “B.E.S.T.” to “OFF.” (੬ pg. 53)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

C ^{Enter the PlusCode number.}

VIDEO Plus+ Timer

Programming

Press the number keys to

enter the PlusCode number

of a programme you wish to

record.

With the VIDEO Plus+ system, timer programming is greatly

simplified because each TV programme has a corresponding

code number which your unit is able to recognize.

● If you make a mistake, press &

and input the correct number.

Before performing the VIDEO Plus+ Timer

Programming:

● Make sure that the unit’s built-in clock is set properly.

● Insert a cassette with the safety tab in place. The unit will

come on automatically.

● Turn on the TV and select the video channel (or AV mode).

● Slide the TV/VCR/DVD switch on the remote control to the

right.

D ^{Access the VIDEO Plus+ Program screen.}

VIDEO Plus+ Program screen

appears (if you’re just starting

out, “P1” appears).

Press ENTER, then the

Slide to the

right.

IMPORTANT

Make sure the channel position number you wish to record is

displayed; if not, or “TV PROG” shows “– –,” press PR +/– to

input the channel position number on which your unit

receives the station, then press ENTER or e.

● If the number you entered is invalid, “ERROR” appears on the

TV screen. Press & and input a valid PlusCode number.

E ^{Set the tape speed.}

Press p.

F ^{Set the PDC mode.}

Press PDC (number key “7”) to select “ON” or “OFF.”

● If “VPS/PDC ON” is displayed on the TV screen, “PDC” is set

to “ON.”

● If “VPS/PDC OFF” is displayed on the TV screen, “PDC” is set

to “OFF.”

੬ “PDC Recording” on page 25.

● VPS (Video Programme System) recording is not currently

available in the U.K. and not possible with this unit.

A ^{Select the VHS deck.}

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the unit

On the remote control

Press VCR so that the VCR indicator lights up.

B ^{Access the VIDEO Plus+ screen.}

Press PROG.

Download from Www.Somanuals.com. All Manuals Search And Download.

G ^{Return to the normal screen.}

PDC Recording

Press PROG or ENTER. “PROGRAM COMPLETED”

appears on the TV screen for about 5 seconds, then the

normal screen appears.

Now available from some TV stations, PDC (Programme

Delivery Control) is a service designed to assure safe,

accurate timer recording. With this system, special code

signals are transmitted together with the audio/video signals.

These code signals control your unit and have precedence

over the advertised times which you may have preset into the

timer. This means that your unit will start and stop recording

when the preset TV programmes actually start and end —

even if the broadcast time of a preset TV programme is

changed from what has been advertised. PDC is currently

available nationally on BBC1, BBC2, Ch.4 and Ch.5, except

from a few small relay transmitters. Ch.3 operates a PDC

service in some areas. All channels intend to offer this

service in due course. Check your TV programme listing

guide for latest information. If the channel you intend to

record does not offer a PDC service your unit will not start

recording if PDC has been selected. Be sure to set PDC to

“OFF” if PDC is not available on your selected channel.

(See step F on page 24 and step I on page 26.

● Repeat steps B – G for each additional programme.

H ^{Engage the unit’s timer mode.}

Press #. The unit turns off automatically and “#”

appears on the front display panel.

● To disengage the timer mode, press # again.

NOTES:

● To Change The Stop Time:

— press STOP +/– after pressing ENTER in step D. You can

compensate for anticipated programme schedule delays.

● To Timer-Record Weekly Or Daily Serials:

— after pressing ENTER in step D, press WEEKLY (number key

“9”) for weekly serials or DAILY (number key “8”) for daily

serials (Monday — Friday). Either “WEEKLY” or “DAILY”

appears on the TV screen. Pressing the button again makes the

corresponding indication disappear.

● You can programme this unit to timer-record as many as 8

programmes. If you try to programme the unit to record a

ninth, “PROGRAM FULL” appears on the TV screen and

“FULL” appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes. (੬ pg. 27)

● If there is a conflict in the timer schedule and one programme

overlaps with another, the programme starting earlier or

programme with the lower programme number will be

recorded.

NOTES:

● When you use Express Timer Programming, set the start

time (PDC time) exactly as advertised in the TV listing. A

different time than advertised will result in no recording.

● PDC recording is also possible when a satellite receiver or

a cable system is connected to L-2 IN/DECODER

connector on your unit.

● PDC recording is also possible via the L-1 IN/OUT

connector.

Satellite Receiver Users

To timer-record a satellite broadcast using the VIDEO Plus+

system:

A Set “L-2 SELECT” to “A/V.” (੬ pg. 54)

B Perform steps A – H.

C Set the satellite receiver to the appropriate channel before

the selected programme begins.

D Leave the satellite receiver’s power on.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

D ^{Enter the programme start time.}

Express Timer

Programming

Press START +/– to enter the

time you want recording to

start.

● Press and hold START +/– to

move in 30-minute

increments, or press and

release repeatedly to move 1

minute at a time.

If you do not know the PlusCode number for the programme you

wish to record, use the following procedure to set your unit to

timer-record the programme.

Before performing Express Timer Programming:

● Make sure that the unit’s built-in clock is set properly.

● Insert a cassette with the safety tab in place. The unit will

come on automatically.

● Turn on the TV and select the video channel (or AV mode).

● Slide the TV/VCR/DVD switch on the remote control to the

right.

E ^{Enter the programme stop time.}

Press STOP +/– to enter the time you want recording to

stop.

● Press and hold STOP +/– to move in 30-minute increments, or

press and release repeatedly to move 1 minute at a time.

Slide to the

right.

F ^{Enter the programme date.}

Press DATE +/–.

● The current date appears on the TV screen. The date you enter

appears in its place.

G ^{Enter the channel position.}

Press PR +/–.

Example: To timer-record the programme from 21:00 to

22:00 on 25th December, on channel 1.

H ^{Set the tape speed.}

Press p.

A ^{Select the VHS deck.}

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

I ^{Set the PDC mode.}

On the unit

Press PDC (number key “7”) to select “ON” or “OFF.”

● If “VPS/PDC ON” is displayed on the TV screen, “PDC” is set

to “ON.”

● If “VPS/PDC OFF” is displayed on the TV screen, “PDC” is set

to “OFF.”

੬ “PDC Recording” on page 25.

On the remote control

Press VCR so that the VCR indicator lights up.

● VPS (Video Programme System) recording is not currently

available in the U.K. and not possible with this unit.

B ^{Access the VIDEO Plus+ screen.}

Press PROG.

J ^{Return to the normal screen.}

Press PROG or ENTER. “PROGRAM COMPLETED”

appears on the TV screen for about 5 seconds, then the

normal screen appears.

C ^{Access the Programme screen.}

Press START +/–. (If you’re

just starting out, “P1”

appears.)

● Repeat steps B – J for each additional programme.

K ^{Engage the unit’s timer mode.}

Press #. The unit turns off automatically and “#”

appears on the front display panel.

● To disengage the timer mode, press # again.

Download from Www.Somanuals.com. All Manuals Search And Download.

To Timer-Record Weekly Or Daily Serials:

Check, Cancel and Change Programmes

— anytime during steps D through I, press WEEKLY (number

key “9”) for weekly serials or DAILY (number key “8”) for daily

serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears

on the TV screen. Pressing the button again makes the

corresponding indication disappear.

A ^{Disengage the timer mode.}

Press #, then press 1.

NOTES:

● You can programme this unit to timer-record as many as 8

programmes. If you try to programme the unit to record a

ninth, “PROGRAM FULL” appears on the TV screen and

“FULL” appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes. (੬ “To cancel or change a programme”)

● If there is a conflict in the timer schedule and one programme

overlaps with another, the programme starting earlier or

programme with the lower programme number will be

recorded.

B ^{Access the Programme Check screen.}

Press ".

Satellite Receiver Users

To timer-record a satellite broadcast using Express Timer

Programming:

A Set “L-2 SELECT” to “A/V.” (੬ pg. 54)

B Perform steps A – K. Enter “L-2” for the channel position

in step G.

C Set the satellite receiver to the appropriate channel before

the selected programme begins.

D Leave the satellite receiver’s power on.

C ^{Access the Programme screen.}

Press " again to check

more information. Each time

you press ", the next

programme’s information

appears.

To cancel or change a programme

D ^{Cancel or change a programme.}

Press & to cancel a programme. To change programme

settings, press the appropriate button: START +/–,

STOP +/–, DATE +/–, PR +/–, PDC (number key “7”),

DAILY (number key “8”), WEEKLY (number key “9”) and/

or p.

E ^{Return to the normal screen.}

Press " as many times as necessary. If there are still

some programmes remaining, go on to step F.

F ^{Return to the timer mode.}

Press #.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

C ^{Cancel or change programme setting.}

Slide to the

right.

To cancel a programme, press & when the Programme

screen you do not want is shown. “PROGRAM

COMPLETED” appears on the TV screen for about 5

seconds, then the normal screen appears.

To change a programme, press the appropriate button:

START +/–, STOP +/–, DATE +/–, PR +/–, PDC (number

key “7”), DAILY (number key “8”), WEEKLY (number key

“9”) and/or p when the Programme screen on which

you want to make changes is shown, then press ENTER.

“PROGRAM COMPLETED” appears on the TV screen for

about 5 seconds, then the normal screen appears.

NOTE:

If the overlap is not yet solved, or another overlap occurs with

the timer programme setting after making the last correction on a

programme, the conflicting programmes will be shown on the

Programme Check screen again. Repeat the above steps again

until the overlap is solved.

Automatic Satellite

When Programmes Overlap Each

Other

Programme Recording

If “PROGRAM OVERLAPPED” appears, you have another

programme overlapping the programme you have just made.

The Programme Check screen appears and conflicting

programmes will start blinking.

This function allows you to automatically record a

satellite programme which is timer-programmed on your

external satellite receiver. Connect a satellite receiver to

the unit’s L-2 IN/DECODER connector and programme

the timer on the satellite receiver. The unit starts or stops

recording by the signals input from the satellite receiver.

After recording, the unit’s power shuts off automatically.

ATTENTION

● Be sure not to turn on the satellite receiver before the

programme is executed; otherwise, the unit will start

recording when the satellite receiver’s power is turned on.

● If you have connected another appliance other than a

satellite receiver to the L-2 IN/DECODER connector, be

sure not to engage the Automatic Satellite Programme

Recording mode; otherwise, the unit will start recording

when the connected appliance’s power is turned on.

● Automatic Satellite Programme Recording and timer-

recording cannot be done at the same time.

Example: Programme 1 (you have just made) and

Programme 4 overlap each other.

A ^{Confirm the overlapping programmes.}

Overlapping programmes blink on the TV screen.

B ^{Select the programme to modify.}

Press rt, then press ENTER or e.

● You can only select one of the overlapping programmes.

NOTE:

If you do not mind this overlap, press PROG to finish the timer

programme setting. The programme with the lower programme

number will be recorded and the other one will not be recorded

correctly. If no changes are made for approximately 1 minute,

the unit will return to the normal screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES:

Before performing the following steps:

● Make sure the satellite receiver is connected to the unit’s

L-2 IN/DECODER connector. (੬ pg. 50)

● Programme the timer on the satellite receiver.

● Insert a cassette with the safety tab in place.

● Slide the TV/VCR/DVD switch on the remote control to the

right.

● Operations on the DVD deck are not possible when the

Automatic Satellite Programme Recording mode is engaged or

timer recording is in progress.

● To disengage the Automatic Satellite Programme Recording

mode, press REC LINK. The “N” indicator goes off.

● If the unit’s power is off, it is not possible to engage the

Automatic Satellite Programme Recording mode.

● In step D, if the “N” indicator does not light but instead blinks

quickly even though your satellite receiver’s power is off,

Automatic Satellite Programme Recording will not work

properly with that satellite receiver*. If this is the case, perform

“Express Timer Programming” (੬ pg. 26) to timer-record a

satellite programme.

* Some satellite receivers output signals even if the power is off.

Automatic Satellite Programme Recording is not possible with those

satellite receivers.

● The “N” indicator blinks while Automatic Satellite Programme

Recording is in progress.

A ^{Select the VHS deck.}

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

● For timer programming of the satellite receiver, refer to the

instruction manual of the satellite receiver.

● Automatic Satellite Programme Recording is not possible if

your satellite receiver does not have a timer.

B ^{Select the L-2 SELECT mode.}

Set “L-2 SELECT” to “A/V” or “SAT.” (੬ pg. 54)

● Pressing the unit’s 1 button while Automatic Satellite

Programme Recording is in progress turns off the unit’s power

and disengages the Automatic Satellite Programme Recording

mode.

● If there are more than one satellite programmes you wish to

record with Automatic Satellite Programme Recording, it is not

possible to set different tape speeds for each programme.

● Depending on the type of satellite receiver, the unit may not

record a slight portion of the beginning of the programme or

may record slightly longer than the actual length of the

programme.

● If you engage the Automatic Satellite Programme Recording

mode when the satellite receiver’s power is on, the unit will

not start Automatic Satellite Programme Recording even

though the “N” and “#” indicators blink. When the satellite

receiver shuts off once and is turned back on again, the unit

starts recording.

● When you select “SAT,” refer to “IMPORTANT” on page 50.

C ^{Set the tape speed.}

Press p.

Engage the Automatic Satellite Programme

Recording mode.

On the unit

Press and hold SAT# for

about 2 seconds.

On the remote control

Press and hold REC LINK

for about 2 seconds.

● The “N” and “#” indicators

light up and the unit turns

off automatically.

● You can also record a programme from your cable system in

the same way if the system has a timer.

● The B.E.S.T. system (੬ pg. 23) does not work while Automatic

Satellite Programme Recording is in progress.

● Just Clock (੬ pg. 65) does not work when the Automatic

Satellite Programme Recording mode is engaged.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK

A ^{Load the disc.}

Basic Playback

● For details, refer to “Placing a Disc” (੬ pg. 6).

B ^{Select the DVD deck.}

Press VCR/DVD repeatedly so that the DVD indicator

lights up.

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

On the unit

On the remote control

Press DVD so that the DVD indicator lights up.

C ^{Start playback.}

Press 4.

Example: DVD VIDEO

Title number

Chapter number

Slide to the

right.

Playback time

● You can switch the display on the front display panel between

the title/chapter/track number and the playback time by

pressing – –:– –.

● It may take a few seconds to start playback.

● When inserting a DVD or Video CD disc, a menu display may

appear on the TV screen. To play back from the menu, refer to

“Locating a Desired Scene Using the DVD Menu” (੬ pg. 31)

or “Locating a Desired Scene Using the Menu of a Video CD/

SVCD with Playback Control (PBC) Function” (੬ pg. 31).

D ^{Pause playback.}

Press 9.

● To resume normal playback, press 4.

E ^{Stop playback.}

Press 8.

● When “RESUME” (੬ pg. 57) is “ON” or “DISC RESUME,” the

unit memorizes the position on the disc where you have

interrupted playback.

ATTENTION

● You can not use the DVD deck when the VHS deck is in

the Automatic Satellite Programme standby and recording

mode.

-To resume playback, press 4.

-To stop playback completely, press 8 again.

● Press x on the DVD deck to open the disc tray, then remove

the disc.

● You can use the DVD deck when the VHS deck is in the

timer standby mode.

● If the unit does not accept an operation,

TV screen. (Operations are occasionally unacceptable

even if is not displayed.)

appears on the

Download from Www.Somanuals.com. All Manuals Search And Download.

2 Start playback.

Press the appropriate number keys.

Playback Features

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

● The unit starts playback of the selected item.

● When “NEXT” or “PREVIOUS” appears on the TV screen:

Pressing 6 advances to the next page.

Pressing 2 returns to the previous page.

● The method of the operation is different depending on the

disc.

To cancel PBC

Start playback by using the number keys instead of 4.

Locating a Desired Scene Using the

DVD Menu

To reactivate PBC

● Press TOP MENU or MENU.

● Press 8 to stop playback, then press 4

Locating the Start Point of the Item or

Skip the Item

DVD VIDEO discs generally have their own menus which show

the disc contents. These menus contain various items such as

titles of movies, names of songs, or artist information, and

display them on the TV screen. You can locate a desired scene

using the DVD menu.

Press 2 or 6 during playback.

1 Access the DVD menu.

Press TOP MENU or MENU.

Example:

Current position

To locate the beginning of

item B from the current

position, press 2 twice.

To locate the beginning of

item D from the current

position, press 6 once.

● When the specified item is

located, playback begins

automatically.

2 Start playback.

Press rt w e to select a

desired item, then press

ENTER.

● It may be possible to select the

desired item using the number

keys depending on the disc.

Example:

The number you press the button

Using the number keys

For DVD VIDEO

● While stopped: title is selected.

Locating a Desired Scene Using the

Menu of a Video CD/SVCD with

Playback Control (PBC) Function

● While playing back: chapter is selected.

For Video CD/SVCD/Audio CD

Track is selected.

Examples:

To select 5, press the number key “5.”

To select 25, press the number key “+10,” “+10,” then “5.”

To select 40, press number key “+10” three times, then “10.”

Some Video CD/SVCD discs support the PBC function. PBC is an

abbreviation of “PlayBack Control.” A Video CD/SVCD disc

recorded with PBC has its own menus, such as a list of the songs

on the disc. You can locate a specific scene by using the menu.

1 Access the PBC menu.

In stop mode

Press 4.

● Depending on a disc, PBC

menu may automatically appear

on the TV screen by simply

loading a disc on the unit. “Pbc”

appears on the front display

panel.

During playback

Press RETURN.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Still Picture/Frame-By-Frame

Playback

Slide to the

right.

1 Pause during playback.

Press 9.

2 Activate frame-by-frame playback.

REPEAT

ON SCREEN

Press 9 to advance a still picture.

● To resume normal playback, press 4.

ZOOM

Slow Motion

During playback, press 9, then press 3 for reverse

slow motion playback, or 5 for forward slow motion

playback.

● Each press of 5 changes the playback speed as follows:

1/32]1/16]1/4]1/2

● Each press of 3 changes the playback speed as follows

(only for DVD VIDEO discs):

–1/32]–1/16]–1/4]–1/2

● To resume normal playback, press 4.

Variable Speed Search

NOTES:

● Reverse slow motion playback is possible only with the DVD

VIDEO discs.

● This function may not works for some Video CD or SVCD.

During playback, press 5 for forward variable speed

search, or 3 for reverse variable speed search.

● The more times you press, the faster the playback picture

moves.

Zooming

● To resume normal playback, press 4.

During playback, press and hold 6 for forward

variable speed search, or press and hold 2 for reverse

variable speed search.

Press ZOOM during playback or while paused.

● Each press of ZOOM changes the magnification as follows:

1.5x]2x]4x

● While zoomed, the picture may look coarse or distorted.

● While you press and hold the button, the image is played back

at 5x speed.

● To resume normal playback, release 2 or 6.

NOTE:

During varirable speed search the sound will be muted except

when playing an Audio CD disc or when playing a DVD VIDEO

disc at 1.5x speed search mode.

Zoomed-in area

Current magnification

One Touch Replay

Press rt w e to move the

zoomed-in scene.

● To resume normal playback,

press ZOOM repeatedly to select

the normal size.

Press

while playing back a DVD VIDEO disc.

The playback position moves back about 10 seconds before the

current position (only within the same title).

Download from Www.Somanuals.com. All Manuals Search And Download.

Repeat Playback

A-B Repeat Playback

You can repeat playback as you like according to the type of

disc.

You can repeat the desired part.

DVD VIDEO/Audio CD:during playback

Video CD/SVCD:during playback with PBC disactivated

DVD VIDEO:

Audio CD:

during playback or in stop mode

Video CD/SVCD: in stop mode or during playback with PBC

disactivated

A ^{Access the on-screen bar.}

the TV screen.

Press ON SCREEN twice. The on-screen bar appears on

A ^{Access the repeat mode.}

Press REPEAT.

B ^{Select the menu item.}

● Repeat mode is displayed on the TV.

Press w e to move H to

, then press ENTER.

B ^{Select the repeat mode.}

● The following pop-up window appears under the selected

item.

Press REPEAT repeatedly to select the desired repeat

mode.

DVD VIDEO

CHAP]TITLE]OFF](Back to the beginning)

CHAPTER: The current chapter is played back repeatedly.

TITLE:

The current title is played back repeatedly.

Each title and chapter is played back once.

C ^{Select the repeat mode.}

OFF:

Press rt repeatedly to select “A-B.”

Video CD/SVCD/Audio CD

TRACK]ALL]OFF](Back to the beginning)

D ^{Select the start point.}

The current track is played back repeatedly.

TRACK:

ALL:

Press ENTER at the beginning of the part you want to

repeat (point A).

All tracks are played back repeatedly.

Each track is played back once.

OFF:

● The following display appears in the on-screen bar.

To cancel Repeat Playback,

Press REPEAT repeatedly until “OFF” appears on the TV

screen.

NOTES:

E ^{Select the end point.}

● Repeat Playback is not possible with a Video CD or SVCD

with PBC function.

Press ENTER at the end of the part you want to repeat (point

B).

● Repeat Playback may not work properly depending on the

type of disc being used.

● You cannot select A-B Repeat Playback by pressing REPEAT.

● A-B Repeat Playback starts. The selected part of the disc

(between point A and B) is played repeatedly.

To cancel A-B Repeat Playback

Repeat from step A, select “OFF” in step C, then press

ENTER.

To clear the on-screen bar

Press ON SCREEN.

NOTE:

The points A and B must be set in the same title or track.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Example:

To play back from a point 2 (hours): 34 (minutes): 08 (seconds)

elapsed

Slide to the

right.

TIME _ : _ _ : _ _

TIME _2 : _3 _ : _ _

TIME _2 : _3 _4 : _0 _

TIME _2 : _ _ : _ _

Press 3

Press 2

Press 4

Press 8

TIME _2 : _3 _4 : _ _

Press 0

TTIIMMEE _2 ::_3 _4 ::_0 _8

If you have specified a wrong selection,

Press w repeatedly until the wrong number is erased,

then press number keys to enter the correct numbers.

● The unit starts playback from the specified time.

To clear the on-screen bar

Press ON SCREEN.

NOTES:

● Some DVD VIDEO discs do not contain time information, and

it is not possible to use the Time Search function.

● Time Search cannot be used during Programme and Random

Playback.

Time Search

Subtitle Selection

You can play back a disc from the desired point by specifying the

elapsed time from the beginning of the current title (for DVD

VIDEO) or the disc (for Audio CD/Video CD) using the Time

Search.

You can select subtitle language.

● During playback

DVD VIDEO/Audio CD: during playback or in stop mode

Video CD/SVCD: during playback with PBC disactivated or in

stop mode

A ^{Access the menu.}

Press SUBTITLE.

● The following pop-up window appears on the TV screen.

A ^{Access the on-screen bar.}

the TV screen.

Example (DVD):“ENGLISH” is selected out of 3 subtitle

languages recorded.

Press ON SCREEN twice. The on-screen bar appears on

B ^{Select the menu item.}

Press w e to move H to

, then press ENTER.

● The following pop-up window appears under the selected

item.

B ^{Select the subtitle language.}

Press rt or SUBTITLE repeatedly to select the desired

subtitle language, then press ENTER.

● Each time you press the button, the subtitle language changes.

● The pop-up window disappears if no operation is done for

about several seconds.

C ^{Select the time.}

Press the number keys (0-9) to enter the time, then press

ENTER.

NOTES:

● For DVD VIDEO

Some subtitle languages are abbreviated in the pop-up

window. See “Language Code List” (੬ pg. 17).

● For SVCD

An SVCD can contain up to four subtitles. Pressing SUBTITLE

changes the subtitles regardless of whether the subtitles are

recorded or not.

Download from Www.Somanuals.com. All Manuals Search And Download.

Angle Selection

Audio Language and Sound Selection

You can enjoy a variety of scene angles if the DVD VIDEO disc

contains “multi-angle” parts, where multiple cameras were used

to shoot the same scene from different angles.

● During playback

The audio selection setting allows you to change the audio

language of a movie, or to listen to karaoke with or without the

vocal.

● During playback

A ^{Access the menu.}

Press ANGLE.

Press A.MONITOR.

● The following pop-up window appears on the TV screen.

Example:The first view angle is selected out of 3 view angles

recorded.

Example: “ENGLISH” is selected out of 3 audio languages

recorded during DVD VIDEO playback.

B ^{Select the audio language.}

B ^{Select the view angle.}

Press rt or A.MONITOR repeatedly to select the

desired audio language, then press ENTER.

● Each time you press the button, the audio language changes.

● The pop-up window disappears if no operation is done for

about several seconds.

Press rt or ANGLE repeatedly to select the desired

view angle, then press ENTER.

● Each time you press the button, the angle of the scene

changes.

● The pop-up window disappears if no operation is done for

about several seconds.

DVD VIDEO (example)

Example:

1/3 ENGLISH]2/3 FRENCH]3/3 SPANISH](Back to the

beginning)

1/3]2/3]3/3](Back to the beginning)

1/3

Video CD

ST]L]R](Back to the beginning)

1/3

To listen to normal stereo playback.

ST:

To listen to L (left) audio channel only.

To listen to R (right) audio channel only.

SVCD

ST 1]ST 2]L 1]R 1]L 2]R 2](Back to the beginning)

To listen to normal stereo playback of ST 1 or

ST 2 channel.

ST 1/ST 2:

To listen to the L (left) 1 or 2 audio channel.

To listen to the R (right) 1 or 2 audio channel.

L 1/L 2:

R 1/R 2:

NOTE:

For DVD VIDEO disc, some audio languages are abbreviated in

the pop-up window. See “Language Code List” (੬ pg. 17).

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Examples:

Slide to the

● To select track 5, press the number key “5.”

● To select 25, press the number key “+10,” “+10,” then

right.

“5.”

● To select 40, press number key “+10” three times, then

“10.”

If you have specified a wrong selection

Press rt to move H to the track to be corrected, then press 8.

The track is erased and the next programmed tracks move up.

D ^{Start playback.}

Press 4. Playback starts in the selected order.

● With an Audio CD disc, the programme table remains on the

TV.

● When all of the programmed tracks have been played back,

Programme Playback stops, but the programmed information

remains.

To check the programme contents

During playback, press 8. Playback stops and the

programme table appears on the TV screen.

● You can also check the programme contents through the on-

screen bar during playback.

To clear the programme

Press 8 while playback is stopped and the programme

table appears on the TV screen.

To exit from Programme Playback

After clearing the programme, press ON SCREEN.

Programme Playback

Random Playback

You can play back up to 99 tracks in the desired order.

A ^{Access the on-screen bar.}

You can play back all the tracks on the disc in random order.

Press ON SCREEN twice in stop mode.

A ^{Access the on-screen bar.}

B ^{Select the menu item.}

Press ON SCREEN twice in stop mode.

Press w e to move H to

, then press ENTER.

● The programme table appears under the on-screen bar.

B ^{Select the menu item.}

Press w e to move H to

, then press ENTER.

● Playback starts in random order.

C ^{Select the tracks in the desired order.}

Press the appropriate

number keys to select the

tracks.

Programme time

To clear the on-screen bar

Press ON SCREEN.

Download from Www.Somanuals.com. All Manuals Search And Download.

To adjust picture appearance manually

Sound Effect

C ^{Access the USER menu.}

Press w e repeatedly to select “USER 1” or “USER 2.”

Using the Sound Effect function, you can change the sound field.

● This function works only for analog audio output.

D ^{Select the parameter.}

A ^{Access the selection menu.}

Press rt repeatedly to select a parameter you want to

adjust, then press ENTER.

Press SOUND EFFECT during playback.

● The current setting appears on the TV screen.

● Adjust gradually and confirm picture appearance results are as

preferred.

GAMMA

(LOW/MID/

HIGH):

Adjust this if the neutral color is bright or dark.

The brightness of dark and bright portions is

maintained.

B ^{Select the Sound Effect mode.}

Press SOUND EFFECT repeatedly to select the desired

mode.

BRIGHTNESS Adjust this if the picture is bright or dark on

(–16 to +16):

the whole.

● Each time you press SOUND EFFECT, the Sound Effect mode

changes as follows:

SOUND EFFECT:1]SOUND EFFECT:2]

SOUND EFFECT:3]OFF](Back to the beginning)

● As the value becomes bigger, the Sound Effect works stronger.

● The selection menu disappears if no operation is done for

about several seconds.

CONTRAST

Adjust this if the objects in far and near

positions look unnatural.

(–12 to +12):

SATURATION Adjust this if the picture is whitish or blackish.

(–16 to +16):

TINT

(–16 to +16):

Adjust this if the appearance of flesh tone is

unnatural.

To deactivate Sound Effect

Press SOUND EFFECT repeatedly until “OFF” appears on

the TV screen.

SHARPNESS Adjust this if the picture is indistinct.

(LOW/ HIGH):

Y DELAY

Adjust this if the picture looks separately or

overlapped.

(–2 to +2):

VFP Function

— Adjusting the Picture Quality

● VFP menu disappears and the following pop-up window

appears on the TV screen.

The VFP (Video Fine Processor) function enables you to adjust

the picture character according to the type of programming,

picture tone or personal preference.

E ^{Adjust the parameter.}

A ^{Access the VFP setting menu.}

Press rt repeatedly to change the setting, then press

ENTER.

Press DVD PICTURE during

playback.

● The current VFP settings appear again.

Repeat steps D and E to adjust other parameters.

● The current setting appears on

the TV screen.

To return to the normal screen

Press DVD PICTURE.

NOTE:

B ^{Select the VFP mode.}

The VFP setting screen disappears if no operation is done for

more than about 10 seconds.

Press w e repeatedly.

● Each time you press w e, the VFP mode changes as follows:

NORMAL]CINEMA]USER 1]USER 2](Back to the

beginning)

NORMAL:

CINEMA:

For watching TV in a general room.

For watching a movie software in a room

with suppressed light.

USER 1/

USER 2:

You can adjust parameters that affect the

picture appearance and store the settings. Go

to step C.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Basic Operation on the Menu Bar

Using the On-Screen Bar

A ^{Access the menu bar.}

Press ON SCREEN twice. The menu bar appears on the

TV screen.

You can check disc information while the disc is loaded and you

can use some functions using the on-screen bar. The on-screen

bar allows you the various playback operations.

● The currently selected item is highlighted.

Slide to the

right.

B ^{Select the menu item.}

Press w e to move H to the item you want to work with,

then press ENTER.

After pressing ENTER

● When a pull-down menu appears, press rt to select the

setting you want, then press ENTER.

● When a number-entry box appears, use the number key to

enter the number you want, then press ENTER.

● When changing the indication of playback time, press ENTER

repeatedly to select the setting you want.

ON SCREEN

For details about each function, see page 39.

How to Access the On-Screen Bar

A ^{Access the status bar.}

Press ON SCREEN when a disc is loaded. The status bar

appears on the TV screen.

Example: During DVD VIDEO playback

Transfer

rate

Chapter

number

Playback

status

Title

number

Playback

time

B ^{Access the menu bar.}

Press ON SCREEN again. The menu bar appears under

the status bar.

To clear the on-screen bar

Press ON SCREEN.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Bar Functions for DVD VIDEO

Menu Bar Functions for SVCD/Video

CD/Audio CD

Time mode selection

During playback, selects the time mode shown in the status bar

and on the front display.

Time mode selection

● TOTAL: Current title elapsed time

Selects the time mode shown in the status bar and on the front

display.

● TIME: Current track elapsed time

● REM: Current track remaining time (while in stop mode,

current track total time)

● T.REM: Current title remaining time

● TIME: Current chapter elapsed time

● REM: Current chapter remaining time

Repeat mode (See also page 33)

● TOTAL: Disc elapsed time

● T.REM: Disc remaining time (while in stop mode, disc total

time)

Selects the repeat mode during playback.

● CHAPTER: Current chapter repeat

● TITLE: Current title repeat

● A-B: A-B repeat

● OFF: Repeat mode deactivated

Repeat mode (See also page 33)

Selects the repeat mode.

● TRACK: Current track repeat

● ALL: All track repeat

Time search (See also page 34)

● A-B: A-B repeat

● OFF: Repeat mode deactivated

Specifies a time from the beginning of the current title as the

point from which to begin playback.

CHAP.

Time search (See also page 34)

Chapter search

Specifies a time from the beginning of the disc as the point from

which to begin playback.

During playback, specifies a desired chapter to be played back

from.

PROG.

Program playback (See also page 36)

Audio selection (See also page 35)

While stopped, specifies the playback order of tracks.

During playback, selects the audio language or sound track.

RND.

Random playback (See also page 36)

Subtitle selection (See also page 34)

While stopped, activates random playback.

During playback, selects the subtitle language.

Audio selection (See also page 35)

Angle selection (See also page 35)

During Video CD/SVCD playback, selects the audio channel(s).

During playback, selects a desired scene angle in a multi-angle

part.

Subtitle selection (See also page 34)

During SVCD playback, selects the subtitle.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Basic Operations

Audio/Video Files

Playback

When you insert a disc with groups and files, the Control display

that shows the contents of the disc automatically appears on the

TV screen.

You can specify and play back the desired group/file from the

Control display using the following procedure.

● Turn on the TV and select the video channel (or AV

mode).

Outline

This unit can play back MP3 and JPEG files on a personally

recorded on CD-R/RW and commercially available CD disc.

This unit can also play back DivX files recorded on CD-R/RW

and DVD-R/-RW disc. Some DVD-R and DVD-RW discs

mastered as multi border (multi-session) may not be compatible

with the unit.

● Slide the TV/VCR/DVD switch on the remote

control to the right.

● This unit may be unable to play back the disc due to the

characteristics or recording conditions.

Precautions

About files and folders (groups) on the disc

● The unit recognizes up to the fifth layer of groups, 999 files per

group, and up to 250 groups per disc. Files other than MP3/

JPEG/DivX files count in the 999 total.

● Add the appropriate extension, such as “avi,” “divx,” “jpeg,”

and “mp3,” to the file name.

Slide to the

right.

For making your own disc:

● Use “UDF format” as the disc format for DVD-R/-RW.

● Use “ISO 9660” as the disc format for CD-R/RW.

● The unit does not support “packet writing” for CD-R/RW.

● The unit supports discs recorded with up to five multiple

sessions.

For MP3 files:

MP3i and MP3 Pro are not available.

For JPEG files:

The unit cannot play back a picture of more than 5120 x 3413

pixels (baseline JPEG) or 2048 x 1536 pixels (progressive JPEG).

ZOOM

For DivX files:

● The unit supports DivX 5.x, 4.x and 3.11.

● The unit supports the DivX files whose resolution is 720 x 480

pixels or less (30 fps), and 720 x 576 pixels or less (25 fps).

● Audio stream should conform to MPEG 1 Audio Layer-2 or

MPEG Audio Layer-3 (MP3).

● The unit does not support GMC (Global Motion Compression)

and Q-Pel (Quarter Pixel).

● The file encoded in the interlaced scanning mode may not be

played back correctly.

● The unit has its own Registration Code for DivX playback. If

necessary, you can confirm the Registration Code of your

player using the OTHERS menu screen. (੬ pg. 57)

A ^{Turn on the unit.}

Press 1.

B ^{Select the DVD deck.}

On the unit

Press VCR/DVD repeatedly so that the DVD indicator

lights up.

On the remote control

Press DVD so that the DVD indicator lights up.

Download from Www.Somanuals.com. All Manuals Search And Download.

Zooming

C ^{Load the disc.}

Press ZOOM during playback or while paused.

● For details, refer to “Placing a Disc” (੬ pg. 6).

● The Control display appears on the TV.

● Each time you press ZOOM, the magnification changes:

- 2 times for DivX files (available only during playback)

- 1.5 and 2 times for JPEG files (This function is not available

for some JPEG files depending on their resolution size and

JPEG format.)

Current playback mode

Select these sections to

show the upper layer.

DISC CONTROL

Rotating/Reflecting a Still Picture

NORMAL

GROUP

MP3

While a still picture is played back:

● Pressing w e rotates the picture by 90°.

● Pressing r reflects the picture vertically.

● Pressing t reflects the picture horizontally.

PICT01.jpg

PICT02.jpg

PICT03.jpg

MUSIC01.mp3

MUSIC02.mp3

SLIDESHOW

MIX

Repeat Playback

A ^{Change the playback mode.}

Control display.

File column

Current group

Press w e to select the current playback mode on the

Selected file

Group column

B ^{Select the repeat mode.}

mode.

D ^{Select a group.}

Press ENTER repeatedly to select the desired repeat

Press w e to select the desired group, then press ENTER.

REPEAT

The current file is played back repeatedly.

E ^{Start playback.}

REPEAT

GROUP:

The all files in the current group are played back

repeatedly.

Press rt to select the desired file, then press ENTER or

All files on the disc is played back repeatedly.

REPEAT

ALL:

● When press ENTER, the unit play the selected file.

● When press 4, the unit start continuous playback of the

group from the selected file.

C ^{Start Repeat Playback.}

F ^{Stop playback.}

Press w e to move the cursor bar to the file column, then

press 4.

Press 8. The Control display appears on the TV screen.

● Press x on the DVD deck to open the disc tray, then remove

the disc.

To cancel Repeat Playback,

Select “NORMAL” in step B above.

To pause playback

Press 9.

● To resume normal playback, press 4.

To reverse or advance DivX file playback rapidly

During playback of DivX file, press 3 or 5.

● Each time you press 3 or 5, the playback speed changes

with the following indication on the TV screen:

3 1/5 1]3 2/5 2]3 3/5 3]3 4/5 4

The higher the value is, the faster the playback speed is.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Random Playback

Slide to the

right.

A ^{Change the playback mode.}

Press w e to select the current playback mode on the

Control display.

B ^{Select the random playback mode.}

Press ENTER repeatedly to select “RANDOM.”

C ^{Start Random Playback.}

Press w e to move the cursor bar to the file column, then

press 4.

● All files in the selected group are played back in random order.

SET UP

To cancel Random Playback,

Select “NORMAL” in step B above.

Programme Playback

A ^{Change the playback mode.}

Press w e to select the current playback mode on the

Control display.

B ^{Select the programme playback mode.}

Press ENTER repeatedly to select “PROGRAM.”

C ^{Select files.}

Press rtw e to select the desired file, then press

ENTER.

● Repeat step 3 until all the desired files are programmed.

● To erase the last programmed file, press w e to move the

cursor bar to the programmed file column, then press 8.

D ^{Start Programme Playback.}

Press 4.

To cancel Programme Playback,

Select “NORMAL” in step B above.

Download from Www.Somanuals.com. All Manuals Search And Download.

Slide Show Playback (JPEG Files)

You can display JPEG files (still pictures) one after another

automatically.

Press 4 while a JPEG file is selected on the Control

display.

To keep showing the current picture

Press 9

Changing the Picture of the Opening

Display

You can change and set the opening display to your favorite

image.

A ^{Play back a JPEG file of your favorite image.}

B ^{Access the PICTURE menu screen.}

Press SET UP, then press w e to show the PICUTRE

menu screen.

C ^{Select “BACKGROUND.”}

Press rt to select “BACKGROUND,” then press ENTER.

D ^{Select “SAVE AS BACKGROUND.”}

Press rt to select “SAVE AS BACKGROUND,” then

press ENTER.

E ^{Register your image.}

Press rt to select “YES,” then press ENTER.

The player starts reading the JPEG file, and the opening

screen is changed after reading the file.

To return to the normal screen

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING (VHS DECK)

A ^{Make connections.}

Editing from a Camcorder

You can use a camcorder as the source player and your

unit as the recording deck.

Connect the camcorder’s AUDIO OUT and VIDEO OUT

connectors to the unit’s front panel AUDIO and VIDEO

input connectors.

Slide the TV/VCR/DVD switch on the remote control

to the right.

● When using a monaural camcorder, connect its AUDIO OUT

connector to the AUDIO L input connector on your unit.

● When a Master Edit Control-equipped JVC camcorder is used,

the camcorder is capable of controlling the unit. Refer to the

camcorder’s instruction manual for operating procedure.

Recorder

B ^{Select the VHS deck.}

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

To PAUSE

connector

AUDIO input

On the remote control

Press VCR so that the VCR indicator lights up.

Audio cable (not provided)

Video cable (not provided)

Mini-plug cable

(not provided)

(JVC camcorder

only)

C ^{Set the unit’s input mode.}

Press AUX (number key “0”) and/or PR to select “F-1.”

VIDEO input

VIDEO OUT

AUDIO OUT

D ^{Set the edit mode.}

See “PICTURE CONTROL” on page 53.

E ^{Engage the Record Pause mode.}

EDIT

Player

Use 4, 3, or 5 to locate the point where you start

recording, then press and hold 9 and press 7 to engage

the Record Pause mode.

F ^{Start the camcorder.}

Engage the Play mode of the camcorder.

G ^{Start the unit.}

Press 4 to engage the Record mode of the unit.

NOTES:

● All necessary cables can be obtained from your dealer.

● When you select “EDIT” to dub tapes in step D, be sure to

select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”)

after you finish dubbing the tapes.

Download from Www.Somanuals.com. All Manuals Search And Download.

B ^{Select the VHS deck.}

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

Editing to or from

On the unit

Another Video Recorder

You can use your unit as the source player or as the

recording deck.

On the remote control

Press VCR so that the VCR indicator lights up.

A When using your unit as the source player:

Player

Your unit

C ^{Set the input mode of recording deck.}

With this unit, press AUX (number key “0”) and/or PR to

select “L-1” for the L-1 IN/OUT connector, or “L-2” for

the L-2 IN/DECODER connector, depending on the

connector being used.

● When using another recorder as the recording deck, refer to its

instruction manual.

AV mode

21-pin SCART cable

(not provided)

● When using the L-2 IN/DECODER connector, set “L-2

SELECT” to “A/V.” (੬ pg. 54)

Another recorder

D ^{Set the edit mode.}

Recorder

See “PICTURE CONTROL” on page 53.

B When using your unit as the recording deck:

Recorder

Engage the Record Pause mode of the

recording deck.

Your unit

Locate the point where you start recording, then engage

the Record Pause mode.

AV mode

F ^{Start the source player.}

Engage the Play mode of the source player.

21-pin SCART cable

(not provided)

G ^{Start the recording deck.}

Another recorder

Engage the Record mode of the recording deck.

Player

NOTES:

● All necessary cables can be obtained from your dealer.

● When you select “EDIT” to dub tapes in step D, be sure to

select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”)

after you finish dubbing the tapes.

Slide the TV/VCR/DVD switch on the remote control

to the right.

● When you use this unit as the source player for editing, be sure

to set “O.S.D.” to “OFF” before starting. (੬ pg. 53)

A ^{Make connections.}

Connect the player’s 21-pin SCART connector to the

unit’s 21-pin SCART connector as illustrated.

A When using your unit as the source player:

— connect its L-1 IN/OUT connector to the recording

deck.

B When using your unit as the recording deck:

— connect its L-1 IN/OUT or L-2 IN/DECODER

connector to the source player.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING (VHS DECK) (cont.)

C ^{Prepare the DVD deck for dubbing.}

B Start playback and search for the point where you

want to start dubbing by pressing 4, 5 or 3.

Dubbing ^{(from DVD to VHS)}

However, it is not possible to dub copy-protected discs.

In such case, “ERROR” appears on the front display panel.

You can dub selected scenes from the DVD disc to a cassette,

starting and stopping wherever you wish.

A Press DVD.

D ^{Start dubbing.}

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

A little before the dubbing start point, press and hold 7,

then press 4 on the remote control.

● “dub” lights on the front display panel.

Slide to the

right.

E ^{End dubbing.}

Press 8.

● Be sure to press 8 while the VCR indicator lights up on the

unit.

● If you press 8 or x with the DVD deck selected, the dubbing

stopped, but the opening screen is also recorded.

● When you have finished dubbing, press DVD to select the

DVD deck and press 8 to stop playback.

NOTES:

● Set “ON SCREEN GUIDE” to “OFF” (੬ pg. 57) if you do not

want to record the on-screen display for DVD discs during

dubbing.

● There may be a discrepancy of several seconds between where

you intend editing to start, and where it actually starts.

● The superimposed indication during the operation or dubbing

is not recorded.

● Set “PICTURE CONTROL” to “EDIT.” (੬ pg. 53)

A ^{Load a cassette and place a disc.}

For the VHS deck

Insert a cassette with the record safety tab intact.

For the DVD deck

A Press x on the DVD deck to open the disc tray.

B Place the disc in the disc tray.

C Press x on the DVD deck to close the disc tray.

B ^{Prepare the VHS deck for dubbing.}

A Press VCR.

B Press p to select recording speed.

C Search for the point where you want to start dubbing

by pressing 4, 5 or 3 then press 8.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING (DVD DECK)

You can dub selected audio from the DVD or Audio CD disc to

an MD etc.

However, it is not possible to dub copy-protected discs.

Digital Audio Dubbing

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Example: Dubbing to an MD

A ^{Make connections.}

Connect the optical cable between the unit and the

digital audio device.

Recorder

B ^{Place a disc and load an MD.}

For the DVD deck

A Press x on the DVD deck to open the disc tray.

B Place the disc in the disc tray.

C Press x on the DVD deck to close the disc tray.

Digital audio device

(MD deck etc.)

For the digital audio device

Insert an MD.

Optical cable

(not provided)

C ^{Prepare the DVD deck for dubbing.}

A Press DVD and select the audio to be dubbed.

B Search for the point where you want to start dubbing

by pressing 4, 5 or 3 then press 8.

C Press 3 a little, then press 4 to start playback.

D Press 9 to pause playback a little before the start

point.

DIGITAL AUDIO OUT

Player

D ^{Prepare the audio device for dubbing.}

Select the input mode.

Note for connection:

Remove the connector cover from

the unit and remove the protection

cap from the cable.

E ^{Start dubbing.}

A Press 4 to start playback on the DVD deck.

B Start recording on the audio device.

F ^{End dubbing.}

Stop recording on the audio device. Then press 8 to stop

playback on the DVD deck.

NOTES:

● There may be a discrepancy of several seconds between where

you intend editing to start, and where it actually starts.

● You can also dub audio from a Video CD or SVCD. Set

“DIGITAL AUDIO OUTPUT” to “PCM ONLY.” (੬ pg. 15, 56)

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL

On the remote control

Keep pressing VCR down during steps A – B.

Remote Control Functions

Remote A/B/C/D Code Switching

A ^{Change the remote control code.}

Press the number key “1” for A, “2” for B, “3” for C, or

“4” for D.

The remote control is capable of controlling four JVC video units

independently. Each of the units can respond to one of four

codes (A, B, C or D). The remote control is preset to send A code

signals because your unit is initially set to respond to A code

signals. You can easily modify your unit to respond to B, C or D

code signals.

B ^{Set the remote control code.}

Press ENTER to set the code.

On the unit

Before performing the following steps:

Slide the TV/VCR/DVD switch on the remote control to the

right.

C ^{Turn off the unit.}

Press 1.

Slide to the

right.

D ^{Display the code.}

Press 4 on the unit for over 5 seconds while the unit is

turned off. The code currently set appears on the front

display panel.

● If the code displayed on the front display panel is different

from the code set on the remote control, go to step E.

E ^{Change the unit’s code.}

Press 8 on the remote control. The code currently set on

the remote control will be applied to the unit.

NOTE:

When “POWER SAVE” is set to “ON” (੬ pg. 54), it is

impossible to change the remote code.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating a JVC TV

Slide the TV/VCR/DVD switch on the

remote control to the left.

Your remote control can operate the basic functions of your JVC

TV set.

Slide to the

left.

B ^{Operate the TV.}

+/– (Volume), TV PR +/–,

● For some JVC TVs, you must press ENTER after having pressed

the number keys.

Press the corresponding button: TV 1, TV/VCR, TV %

(TV Muting), number keys.

Control Your JVC TV Using Additional Buttons

Use the number keys, and the p button or & button to

select the TV’s channel.

● The p button corresponds to the 1-digit/2-digit entry

switching button (often labelled – /– –) of your TV’s remote

control.

● With some JVC TVs, the & button corresponds to the 10 +

button of your TV’s remote control.

NOTE:

The way these buttons are used is determined by your TV.

Use these buttons as instructed for your TV’s remote control.

IMPORTANT

Although the provided remote control unit is compatible with

JVC televisions, it may not work with your JVC TV, or in some

instances, may have limited function capability.

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM CONNECTIONS

Connecting to a Satellite Receiver

NOTES:

Connect the satellite receiver to the L-2 IN/DECODER

connector, then connect the L-1 IN/OUT connector to

the TV’s connector.

● Set “L-2 SELECT” to “A/V.” (੬ pg. 54)

● You can use the Automatic Satellite Programme Recording

function (੬ pg. 28) with this connection. (VHS deck only)

● To record a programme via the satellite receiver, select L-2

mode by pressing AUX (number key “0”) and/or PR so that

“L-2” appears on the front display panel. (VHS deck only)

● For details, refer to the instruction manual of the satellite

receiver.

Outdoor unit

Satellite cable

Aerial

TV aerial cable

Satellite receiver

ANTENNA IN

ANTENNA OUT

ANTENNA IN

L-1 IN/OUT

L-2 IN/DECODER

ANTENNA OUT

IMPORTANT

When you set “L-2 SELECT” to “SAT” (੬ pg. 54), it is possible to view a satellite broadcast with the TV set to its AV mode even if

the unit is turned off. When the unit is in Stop mode or recording, press TV/VCR on the remote control to turn off the VCR indicator

on the front display panel.

● If you turn on the unit when the satellite receiver’s power is off, nothing appears on the TV screen. In this case, turn on the

satellite receiver, or set the TV to its TV mode, or press TV/VCR on the remote control to set the unit to the video mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting to a Dolby Digital Decoder or an Amplifier

with a Built-In DTS ^{(DVD deck only)}

These instructions enable you to connect your unit to a

Dolby Digital Decoder or an amplifier with built-in DTS.

NOTES:

● For Dolby Digital sound, set “DIGITAL AUDIO OUTPUT” to

“DOLBY DIGITAL/PCM.” (੬ pg. 15, 56)

● For DTS sound, set “DIGITAL AUDIO OUTPUT” to “STREAM/

PCM.” (੬ pg. 15, 56)

Make connections.

Connect the optical cable between the unit and the

Dolby Digital Decoder or amplifier with a built-in DTS.

CAUTIONS:

● This unit has a dynamic range of more than 80 dB with regards

to its Hi-Fi audio capability. It is recommended that you check

the maximum level if you are going to listen to the Hi-Fi audio

signals through a stereo amplifier. A sudden surge in the input

level to the speakers may damage them.

● Some speakers and televisions are specially shielded to

prevent television interference. If both are of the non-shielded

type, do not place the speakers adjacent to the TV set as this

can adversely affect the video playback picture.

Dolby Digital Decoder or

amplifier with built-in DTS

To DIGITAL AUDIO

input

Optical cable

(not provided)

DIGITAL

AUDIO OUT

Note for connection:

Remove the connector cover from

the unit and remove the protection

cap from the cable.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS

A ^{Turn on the unit.}

Mode Set (VHS deck)

Press 1.

You can change various mode settings on the Mode Set

screen by following the procedure described below.

● For each mode setting, see pages 53 to 54.

B ^{Select the VHS deck.}

On the unit

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

Slide to the

right.

C ^{Access the Main Menu screen.}

Press SET UP.

D ^{Access the Mode Set screen.}

Press rt to move the

highlight bar (pointer) to

“MODE SET,” then press

ENTER or e.

E ^{Select the mode.}

Press rt to move the highlight bar (pointer) to the item

you want to change.

F ^{Select the mode setting.}

Press ENTER or e.

G ^{Return to the normal screen.}

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

* The default setting is bold in the table below.

8 AUTO SP]LP TIMER — ON / OFF

8 B.E.S.T. — ON / OFF

When this function is set to “ON”, the unit automatically

You can set the B.E.S.T. (Biconditional Equalised Signal Tracking)

switches to LP mode to allow complete recording if there is not

enough tape to record the entire programme while timer-

recording in SP mode.

system to “ON” or “OFF.” (੬ pg. 23)

NOTES:

For Example:

● When watching a tape recorded with “B.E.S.T.” set to “ON,” it

is recommended that you leave B.E.S.T. on during playback as

well.

Recording a programme of 210 minutes in length onto a 180-

minute tape

Approximately 150 minutes

SP mode

Approximately 60 minutes

LP mode

Total 210 minutes

● When watching a rental tape or one recorded on another

video recorder, or when using this unit as the player for

editing, set B.E.S.T. to your preference.

● The B.E.S.T. system works for both SP and LP modes only after

a tape has been inserted and the Record mode is first initiated.

It does not work during recording.

Make sure you set this function to “ON,” before the timer-

recording starts.

● The B.E.S.T. system does not work while Automatic Satellite

Programme Recording is in progress. (੬ pg. 28)

● In the case of timer recordings, the B.E.S.T. system works

before recording is initiated.

● Once the cassette is ejected, the B.E.S.T. data is cancelled. The

next time the cassette is used for recording, B.E.S.T. is re-

performed.

NOTES:

● If you have programmed the unit to timer-record 2 or more

programmes, the second programme and those thereafter may

not fit on the tape if you set “AUTO SP]LP TIMER” to “ON.”

In this case, make sure the mode is not engaged, then set the

tape speed manually during timer programming.

● In order to ensure that the recording fits on the tape, this

feature may leave a slight non-recorded section at the end of

the tape.

● Pressing the unit’s 7 button while “BEST” is displayed does

not start Instant Timer Recording. (੬ pg. 22)

● There may be some noise and sound disturbance at the point

on the tape where the unit switches from SP to LP mode.

● The Auto SP]LP Timer feature is not available during ITR

(Instant Timer Recording), and the feature will not work

properly with any tapes longer than E-180, or with some tapes

of shorter lengths.

● If you perform timer recording with both PDC and the Auto

SP]LP Timer activated, and the programme goes beyond its

originally scheduled length, there may be times when the

programme cannot be recorded in its entirety.

8 PICTURE CONTROL— AUTO / EDIT / SOFT

This feature helps you to adjust the playback picture quality

according to your preference. Normally select “AUTO.”

AUTO: Provides the optimised picture benefits of the B.E.S.T.

Picture System.

EDIT: Minimizes picture degradation during editing (recording

and playback).

SOFT: Reduces image coarseness when viewing overplayed

tapes containing a lot of noise.

NOTES:

● When you select “EDIT” or “SOFT,” the selected mode will not

change until you select another mode.

● When you select “EDIT” to dub tapes, be sure to select

“AUTO” after you finish dubbing the tapes.

● When “B.E.S.T.” is “OFF”, “PICTURE CONTROL” switches

automatically from “AUTO” to “NORM.”

8 O.S.D. — ON / OFF

When this function is set to “ON,” various operational indicators

appear on the TV screen.

NOTES:

● When you use this unit as the source player for editing, be sure

to set “O.S.D.” to “OFF” before starting.

● During playback, the operation mode indicators may be

disturbed depending on the type of tape being used.

8 DIRECT REC — ON / OFF

When this function is set to “ON,” you can easily start recording

the programme that you are watching on your TV. Press and hold

7 and press 4 on the remote control, or press 7 on the unit.

NOTES:

● When you use the Direct Rec function, be sure to use a TV

offering T-V LINK, etc. and connect a fully-wired 21-pin

SCART cable between the unit and the TV. (੬ pg. 11)

● If “DIRECT REC” is set to “OFF,” the 7 button functions as

described in “Basic Recording” (੬ pg. 21).

● During Direct Rec, “– –” appears on the front display panel.

● When “DIRECT REC” is set to “ON,” if you press any button

just after pressing 7 on the unit (or 7 and 4 on the remote

control), the unit may not function properly.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

8 POWER SAVE — ON / OFF

When this function is set to “ON,” you can reduce the power

consumption while the unit is turned off.

NOTES:

● During Power Save mode:

— the front display panel will be turned off.

— the Just Clock function (੬ pg. 65) does not work.

— the picture may be distorted momentarily when you turn

on/off the unit.

● Power Save does not work when:

— the unit is in the timer mode.

— the unit’s power is turned off after timer-recording or Instant

Timer Recording.

— the Automatic Satellite Programme Recording mode is

engaged. (੬ pg. 28)

— “L-2 SELECT” is set to “DECODER” or “SAT.”

8 VIDEO STABILIZER — ON / OFF

When this function is set to “ON,” you can automatically correct

vertical vibration in the picture when playing back unstable

recordings made on another recorder.

NOTES:

● When you finish viewing a tape, be sure to set this function to

“OFF.”

● Regardless of the setting, this function has no effect during

recording and during special effects playback.

● The on-screen display may jitter vertically when this function

is set to “ON.”

● To watch recordings with close-caption, set this function to

“OFF.”

8 L-2 SELECT — A/V / DECODER / SAT

Set “L-2 SELECT” to the appropriate mode depending on the

type of appliance connected to the unit’s L-2 IN/DECODER

connector.

A/V: To use this unit as the recording deck with the player

connected to the L-2 IN/DECODER connector, or to use the

satellite receiver connected to the L-2 IN/DECODER

connector.

DECODER: To use a decoder connected to the L-2 IN/DECODER

connector.

SAT: To view a satellite programme with the TV set while the

unit is turned off. (੬ pg. 50)

NOTES:

● Decoder function is not available in the U.K.

● If you have a satellite receiver or a decoder connected to the

L-2 IN/DECODER connector, be sure to set “L-2 SELECT” back

to the appropriate mode after editing.

●

If you are not connecting a satellite receiver or a decoder to the

L-2 IN/DECODER connector, leave “L-2 SELECT” set to “A/V.”

● When “L-2 SELECT” is set to “SAT,” “SAT” appears on the TV

screen or front display panel instead of “L-2.”

8 AUTO POWER OFF — 3H / OFF

When this function is set to “3H,” the unit is turned off

automatically if no operation is done within 3 hours. “AUTO

POWER OFF IN 3 MIN” appears on the screen 3 minutes before

the unit is turned off.

Download from Www.Somanuals.com. All Manuals Search And Download.

● The procedure shows how to set “RESUME” to “ON”

on the DVD Set Up menu screen as an example.

Mode Set (DVD deck)

You can change various mode settings on the Mode Set

screen by following the procedure described below.

● For each mode setting, see corresponding pages.

A ^{Turn on the unit.}

Press 1.

MENU LANGUAGE (੬ pg. 16)

AUDIO LANGUAGE (੬ pg. 16)

B ^{Select the DVD deck.}

LANGUAGE

SUBTITLE (੬ pg. 16)

ON SCREEN LANGUAGE (੬ pg. 15)

On the unit

Press VCR/DVD repeatedly so that the DVD indicator

MONITOR TYPE (੬ pg. 15)

lights up.

PICTURE SOURCE (੬ pg. 56)

PICTURE

SCREEN SAVER (੬ pg. 56)

BACKGROUND (੬ pg. 56)

On the remote control

Press DVD so that the DVD indicator lights up.

DIGITAL AUDIO OUTPUT (੬ pg. 15)

ANALOG DOWNMIX (੬ pg. 56)

C ^{Access the DVD Set Up menu screen.}

AUDIO

D. RANGE CONTROL (੬ pg. 56)

OUTPUT LEVEL (੬ pg. 56)

A Press SET UP.

OTHERS

RESUME

B Press w e to select

ON SCREEN GUIDE

DivX REGISTRATION

PARENTAL LOCK

RESUME (੬ pg. 57)

“

OTHERS.”

ON SCREEN GUIDE (੬ pg. 57)

OTHERS

● Each time you press the

button, the setup menus

change as follows;

DivX REGISTRATION (੬ pg. 57)

PARENTAL LOCK (੬ pg. 57)

LANGUAGE] PICTURE] AUDIO ] OTHERS

](Back to the beginning)

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

D ^{Select the mode.}

Press rt to move H to “RESUME,” then press ENTER.

Slide to the

right.

E ^{Select the mode setting.}

Press rt to select “ON,” then press ENTER.

F ^{Return to the normal screen.}

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

* The default setting is bold in the table below.

ANALOG DOWNMIX — DOLBY SURROUND / STEREO

Set to the appropriate mode according to your audio system

when you play back a DVD VIDEO disc recorded with surround

multichannel audio. This setting affects only the analogue audio

output signal from the AUDIO OUT connectors when playing

back a DVD VIDEO disc recorded with surround multichannel

audio.

DOLBY SURROUND: Select this when you enjoy multichannel

surround audio by connecting the unit’s analogue AUDIO

OUTPUT connectors (DVD) to a surround decoder.

Picture Settings

8 MONITOR TYPE —

16:9 / 4:3 LB / 4:3 PS

You can select the monitor type depending on the TV used when

you play back DVD VIDEO discs recorded for wide-screen TVs.

For more details, refer to “Initial Set Up for DVD Deck”

(੬ pg. 15).

STEREO: Select this when you enjoy conventional 2-channel

stereo audio by connecting the unit’s analogue AUDIO

OUTPUT connectors (DVD) to a stereo amplifier/receiver or

TV, or when you dub audio of a DVD VIDEO disc recorded

with surround audio to your MD, cassette, etc.

8 PICTURE SOURCE —

AUTO / FILM / VIDEO (NORMAL) / VIDEO (ACTIVE)

You can obtain optimal picture quality by selecting whether the

content on the disc is processed by field (video source) or by

frame (film source).

Normally set to “AUTO.”

8 D. RANGE CONTROL —

AUTO: Used to play back a disc containing both video and film

source materials. This unit recognizes the picture type (film or

video source) of the current disc according to the disc

information.

WIDE RANGE / NORMAL / TV MODE

The dynamic range (the difference between the loudest sound

and the quietest one) can be compressed during playback of a

programme encoded in Dolby Digital format.

This function takes effect when a DVD VIDEO disc recorded in

Dolby Digital format is played back at low or middle volume.

FILM: Suitable for playing back a film or progressive source disc.

VIDEO (NORMAL): Suitable for playing back a video source disc

with relatively a few movements.

WIDE RANGE: Select this to inactivate this function when you

VIDEO (ACTIVE): Suitable for playing back a video source disc

enjoy wide dynamic range programme.

with relatively a lot of movements.

NORMAL: Normally select this setting to activate this function.

● If the playback picture is unclear or noisy, or the oblique lines

of the picture are rough, try to change to other modes.

TV MODE: Select this when you hear the sound through the TV's

speaker(s).

8 SCREEN SAVER — ON / OFF

8 OUTPUT LEVEL — STANDARD / LOW

The TV screen may be burned out if a static picture is displayed

for a long time. When this function is set to “ON,” the unit

automatically activates the screen saver function if a static

picture, such as an on-screen display or menu is displayed for

over 5 minutes.

You can lower the output level of analog audio to accommodate

the unit to the connected A/V equipment.

STANDARD: Normally select this.

LOW: Select this if the sound output from the speaker is

distorted. The output level of analog audio is lowered.

NOTE:

This function is not available for Audio files playback.

8 BACKGROUND —

STANDARD / USER / SAVE AS BACKGROUND

You can use your favorite image as the opening display.

STANDARD: Select this to display the JVC original image.

USER: Select this to display your favorite image when a JPEG

image is registered.

SAVE AS BACKGROUND: To register a new image, select this

while a JPEG image is displayed on the TV screen.

Audio Settings

8 DIGITAL AUDIO OUTPUT —

PCM ONLY / DOLBY DIGITAL/PCM / STREAM/PCM

Set to the appropriate mode according to the type of the device

connected to DIGITAL AUDIO OUT connector on the rear of

unit.

It is not necessary to set this mode when you connect no device

to the DIGITAL AUDIO OUT connector.

For more details, refer to “Initial Set Up for DVD Deck”

(੬ pg. 15).

Download from Www.Somanuals.com. All Manuals Search And Download.

Output

Playback discs

STREAM/PCM

DTS bitstream

DOLBY DIGITAL/PCM

PCM ONLY

DVD VIDEO with

48 kHz, 16/20/24 bit linear

PCM

48 kHz, 16 bit linear PCM

DVD VIDEO with DTS

48 kHz, 24 bit stereo linear PCM

DVD VIDEO with Dolby

Digital

48 kHz, 24 bit stereo linear

PCM

Dolby Digital bitstream

44.1 kHz, 16 bit stereo linear PCM

44.1 kHz, 24 bit stereo linear PCM

Video CD/SVCD/Audio CD

Audio CD with DTS

DTS bitstream

CD-R/RW recorded MP3

CD-R/RW or DVD-R/RW

recorded DivX

Linear PCM

Parental Lock

NOTES:

● The unit is not equipped with the DTS decoding function.

● When you play back a DVD VIDEO or Audio CD disc with

DTS, use a DTS decoder to get correct signals from your

speakers. Never use the unit’s analog output connectors,

which output incorrect signals that may damage your

speakers.

This function restricts playback of DVD VIDEO discs which

contains violent (and other) scenes according to the level set by

the user. Scenes which are limited by this function are not played

or replaced with other scenes.

8 COUNTRY CODE

● If you connect the analog outputs and digital outputs

simultaneously, be sure to select the source of the amplifier

correctly, or set the level control of the amplifier connected to

the analog outputs to minimum.

Select the code of your country/area. (੬ pg. 58)

8 SET LEVEL

Select the level of restriction. (“1” is the strictest.)

Others Settings

8 PASSWORD

Enter your password by pressing the number keys(0-9).

8 RESUME — ON / OFF / DISC RESUME

8 EXIT

You can select the resume playback mode.

Select this, then press ENTER to go back to the OTHERS menu

ON: The unit resumes playback from the position where

screen.

playback has been stopped if the disc is still in the disc tray.

OFF: This function is deactivated.

DISC RESUME: The unit resumes playback of the last 30 discs

played. The unit retains a memory of the stopped position of

each disc even if the disc is removed from the disc tray.

NOTES:

● Some DVD VIDEO discs cannot be played by this function. If

you try to play such a disc, the PARENTAL LOCK menu screen

appears on the TV screen and asks whether you want to

release the lock or not.

NOTE:

To release the lock and play, select “TEMPORARY RELEASE,”

press ENTER, then enter your password. Otherwise, eject the

disc.

This function is not available for Audio CD discs and Audio/

Video files playback.

● To change the setting of the limitation, you need to enter your

password.

● If you forget your pass word, enter “8888.”

8 ON SCREEN GUIDE — ON / OFF

When this function is set to “ON,” the unit can display “on-

screen guide” icons or characters which show the conditions of

the unit or disc.

8 DivX REGISTRATION

The unit has its own Registration Code for DivX playback. You

can confirm the code of your unit.

NOTE:

Once you played back a disc created by using the Registration

Code, the unit’s code is overwritten by a totally different new

one for copyright protection purpose.

8 PARENTAL LOCK

Select this, then press ENTER to show the PARENTAL LOCK

menu screen for limiting playback by children.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

Country/Area Code List for Parental Lock

AW Aruba

Andorra

Spain

Ethiopia

Finland

Fiji

Falkland Islands (Malvinas)

Micronesia (Federated States of)

Faroe Islands

France

France, Metropolitan

Gabon

United Kingdom

Grenada

Georgia

Saint Lucia

Liechtenstein

Sri Lanka

Liberia

Lesotho

Lithuania

Luxembourg

Latvia

Saudi Arabia

Solomon Islands

Seychelles

Sudan

Sweden

Singapore

Saint Helena

Slovenia

Svalbard and Jan Mayen

Slovakia

Sierra Leone

United Arab Emirates

Afghanistan

Antigua and Barbuda

Anguilla

Albania

Armenia

Netherlands Antilles

Angola

Antarctica

Argentina

American Samoa

Austria

Libyan Arab Jamahiriya

MA Morocco

MC Monaco

MD Moldova, Republic of

MG Madagascar

MH Marshall Islands

SM San Marino

Senegal

SO Somalia

Australia

French Guiana

Ghana

Gibraltar

Mali

Suriname

Sao Tome and Principe

El Salvador

Syrian Arab Republic

Swaziland

Turks and Caicos Islands

Azerbaijan

Bosnia and Herzegovina

Barbados

Bangladesh

Belgium

Burkina Faso

Bulgaria

Bahrain

Burundi

Benin

Bermuda

Brunei Darussalam

Bolivia

Brazil

Bahamas

Bhutan

MM Myanmar

MN Mongolia

MO Macau

Greenland

GM Gambia

Guinea

Northern Mariana Islands

Guadeloupe

Equatorial Guinea

Greece

South Georgia and the South

Sandwich Islands

Guatemala

MQ Martinique

MR Mauritania

MU Mauritius

MV Maldives

MW Malawi

MX Mexico

MY Malaysia

MZ Mozambique

NG Nigeria

NO Norway

NU Niue

TD Chad

TG Togo

TH Thailand

Montserrat

Malta

French Southern Territories

Tajikistan

Tokelau

Guam

GW Guinea-Bissau

HM Heard Island and McDonald

Islands

TM Turkmenistan

TN Tunisia

TO Tonga

TW Taiwan

UA Ukraine

UG Uganda

UM United States Minor Outlying

Islands

UY Uruguay

UZ Uzbekistan

Guyana

Hong Kong

Namibia

New Caledonia

Niger

East Timor

Turkey

Trinidad and Tobago

Tuvalu

Bouvet Island

Honduras

Croatia

Haiti

Hungary

Indonesia

Ireland

Israel

India

British Indian Ocean Territory

Iraq

Iran (Islamic Republic of)

Iceland

Italy

Jamaica

Jordan

Japan

Kenya

BW Botswana

Norfolk Island

Belarus

Belize

Canada

Nicaragua

Netherlands

Tanzania, United Republic of

Cocos (Keeling) Islands

Central African Republic

Congo

Switzerland

Côte d’Ivoire

Cook Islands

Chile

Cameroon

China

Colombia

Costa Rica

Cuba

Cape Verde

Christmas Island

Cyprus

Czech Republic

Germany

Djibouti

Nepal

Nauru

United States

New Zealand

OM Oman

Panama

Peru

French Polynesia

Papua New Guinea

Philippines

Pakistan

Poland

Saint Pierre and Miquelon

Pitcairn

Puerto Rico

Portugal

Vatican City State (Holy See)

Saint Vincent and the Grenadines

Venezuela

PW Palau

QA Qatar

VG Virgin Islands (British)

VI Virgin Islands (U.S.)

VN Viet Nam

VU Vanuatu

WF Wallis and Futuna Islands

WS Samoa

Kyrgyzstan

Cambodia

Kiribati

Comoros

Yemen

Mayotte

Saint Kitts and Nevis

Korea, Democratic People’s

Republic of

Korea, Republic of

Kuwait

Cayman Islands

Kazakhstan

Lao People’s Democratic

Republic

YU Yugoslavia

South Africa

ZM Zambia

Zaire

Denmark

Paraguay

DM Dominica

DO Dominican Republic

Réunion

Romania

Russian Federation

ZW Zimbabwe

Algeria

Ecuador

Estonia

Egypt

Western Sahara

Eritrea

RW Rwanda

Lebanon

Download from Www.Somanuals.com. All Manuals Search And Download.

D ^{Perform Auto Channel Set.}

Tuner Set

Press rt to move the

highlight bar (pointer) to

“AUTO CH SET,” then press

ENTER or e twice.

IMPORTANT

Perform the following steps only if —

— Auto Channel Set has not been set correctly by Auto Set

Up or by Preset Download. (੬ pg. 12, 13)

— you have moved to a different area or if a new station

starts broadcasting in your area.

Your unit needs to memorize all necessary stations in channel

positions in order to record TV programmes. Auto Channel Set

automatically assigns all receivable stations in your area to call

them up by using the PR buttons without going through any

vacant channels.

● When you have connected

the unit to a TV offering T-V

Link via a fully-wired 21-pin

SCART cable (੬ pg. 11), the

unit automatically performs

the Preset Download and the

T-V LINK screen will appear.

(੬ pg. 13)

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

● The Auto Set screen appears,

and remains on screen while

Beginning

End

the unit searches for

receivable stations.

Slide to the

right.

As Auto Channel Set progresses, the “q” mark on the TV screen

moves from left to right. Wait until the TV screen as shown in

step E appears.

E ^{View the Confirmation screen.}

After “SCAN COMPLETED” is

displayed on the TV screen for

about 5 seconds, the

Confirmation screen looking

like the one to the right

appears. The stations your unit

located appear on the

Confirmation screen —

channel positions (PR),

channels (CH) and station names (ID – ੬ pg. 62). The

blueback screen and the programme currently being

broadcast by the blinking station appear alternately for 8

seconds each. To view the next page, use the rt w e

button on the remote control.

● The Guide Program numbers will also be set automatically

during Auto Channel Set.

Auto Channel Set

F ^{Return to the normal screen.}

● Using the Confirmation screen, you can skip or add channel

positions, enter station names and perform other operations.

Refer to pages 60 – 61 for the procedures.

A ^{Turn on the unit.}

Press SET UP.

Press 1.

B ^{Select the VHS deck.}

●

Depending on reception conditions, the stations may not be

stored in order, and the station names may not be stored correctly.

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

IMPORTANT

lights up.

●

In certain reception conditions, station names may not be

stored correctly, and Auto Guide Program Number Set may

not work properly. If the Guide Program numbers are not set

properly when you timer-record a TV programme using the

VIDEO Plus+ system, the unit will record a TV programme

of a different station. When programming the timer using the

VIDEO Plus+ system, be sure to check the desired channel

On the remote control

Press VCR so that the VCR indicator lights up.

C ^{Access the Main Menu screen.}

is selected correctly. (

Programming”)

੬

pg. 24, “VIDEO Plus+^®Timer

Press SET UP.

●

Your unit memorizes all detected stations even if reception

of some of them is poor. You can delete those stations with

an unacceptable picture. (

੬

pg. 60, “Deleting a Channel”)

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

NOTES:

F ^{Enter new channel information.}

● Fine tuning is performed automatically during Auto Channel

Set. If you want to perform tuning manually, refer to page 61.

● If you perform Auto Channel Set when the aerial cable is not

connected properly, “SCAN COMPLETED –NO SIGNAL–”

appears on the TV screen in step E. When this happens, make

sure of the aerial connection and press ENTER; Auto Channel

Set will take place again.

Press ENTER and the Confirmation screen appears.

● Repeat steps C – F as necessary.

G ^{Close the Confirmation screen.}

● To change positions, see “Changing Station Channel Position”

(੬ pg. 61).

If you wish to set station names other than the ones registered

Press SET UP.

Manual Channel Set

●

Store channels that were not stored during Auto Set Up

(੬ pg. 12), Preset Download (੬ pg. 13) or Auto Channel Set

(੬ pg. 59).

in your unit, see “Setting Station Names Manually” (

੬

pg. 61).

ATTENTION

Guide Program numbers are not set when channels are

stored manually. (੬ pg. 24, “VIDEO Plus+^®Timer

Programming”)

A ^{Access the Main Menu screen.}

Press SET UP.

B ^{Access the Confirmation screen.}

Deleting a Channel

Press rt to move the highlight bar (pointer) to

“MANUAL CH SET”, then press ENTER or e. The

Confirmation screen appears.

Perform steps A and B of “Manual Channel Set” on page 60

to access the Confirmation screen before continuing.

C ^{Select the channel position.}

position in which you want to

store a channel begins

blinking, then press ENTER.

The Manual Channel Set

screen appears.

● The blueback screen and the

programme currently being

broadcast by the selected

channel appear alternately for 8

seconds each.

A ^{Select the item.}

blinking.

(Example) To store in position 6.

Press rt w e until an open

Press rt w e until the item you want to delete begins

B ^{Delete a channel.}

Press &.

● The item directly beneath the cancelled one moves up one

line.

● Repeat steps A and B if necessary.

C ^{Close the Confirmation screen.}

D ^{Select the band.}

Press SET UP.

Press rt to change the

band between CH (regular)

and CC (cable), then press e.

E ^{Input the channel.}

Press the number keys to input the channel number you

want to store.

● Input “0” before any single number entries.

● To input the registered station name (ID – ੬ pg. 62), press e

until “– – – –” (ID setting) begins blinking, then press rt.

● For fine tuning adjustment, press e until “+/–” begins blinking,

then press rt. While tuning, “+” or “–” appears.

● When “L-2 SELECT” is set to “A/V” or “SAT,” the “DECODER”

setting cannot be changed. (੬ pg. 54)

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing Station Channel Position

Perform steps A and B of “Manual Channel Set” on page 60

Setting Station Names Manually

You can set station names manually.

to access the Confirmation screen before continuing.

Perform steps A and B of “Manual Channel Set” on page 60

to access the Confirmation screen and then perform steps A

and B of “Setting Station Names by ID Code” above before

continuing.

A ^{Select the item.}

Press rt w e until the item you want to move begins

blinking. Then press ENTER and the station name (ID)

and its channel (CH) number begin blinking.

A ^{Select the character for station name.}

Press e until the first letter of

the station name begins

blinking.

B ^{Select the new position.}

Press rt w e to move the station to the new channel

position, then press ENTER.

Example: If you moved the station in position 4 to position 2, the

stations originally in positions 2 and 3 each move

down one space.

B ^{Enter the new character.}

Press rt to cycle through the characters (A–Z, 0–9, –,

f, +, I (space) ) and stop when the desired character is

indicated, then press e to enter. Enter the remaining

characters the same way (maximum of 4). After entering

all characters, press ENTER.

● Repeat steps A and B if necessary.

● The Confirmation screen appears.

● If you make a mistake, press w until the incorrect character

begins blinking. Then enter the correct character by pressing

rt.

C ^{Close the Confirmation screen.}

Press SET UP.

C ^{Close the Confirmation screen.}

Setting Station Names by ID Code

Set station names by ID codes (“ID” that are registered in your unit.

Press SET UP.

)

NOTE:

Perform steps A and B of “Manual Channel Set” on page 60

to access the Confirmation screen before continuing.

The characters available for the station name (ID) are A–Z, 0–9, –,

, +,

(space) (maximum of 4).

A ^{Select the item.}

Fine-Tuning a Stored Channel

Perform steps A and B of “Manual Channel Set” on page 60

Press rt w e until the item you want begins blinking.

to access the Confirmation screen before continuing.

B ^{Access the Manual Channel Set screen.}

Press ENTER twice.

A ^{Select the channel to fine-tune.}

Press rt w e until the channel you want to tune begins

blinking.

C ^{Select the new station.}

Press e until the station

name (ID) begins blinking,

then press rt until the new

station’s name (ID) you want

to store begins blinking.

Registered station names

(੬ pg. 62) appear as you

press rt.

B ^{Access the Manual Channel Set screen.}

Press ENTER twice. The Manual Channel Set screen

appears.

C ^{Perform tuning.}

Press e until “+/–” begins blinking, then press rt to

obtain the best picture quality. After finishing adjustment,

press ENTER.

D ^{Switch the stations.}

Press ENTER.

● The Confirmation screen appears.

● Repeat steps A – D if necessary.

● The Confirmation screen appears.

● Repeat steps A – C if necessary.

D ^{Close the Confirmation screen.}

E ^{Close the Confirmation screen.}

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

TV Station and ID List

* The “ID” abbreviation is what is shown on-screen in lieu of the station name. The “ID” abbreviation is listed in the Confirmation screen and is displayed

on the TV screen when the unit is tuned to a different station.

STATION NAME

ID*

STATION NAME

ID*

Anglia TV

ARD

ANGL

ARD

SAT

SAT 1

SAT1

SCOT

SC4

ARTE

BBC

Scottish TV

SC4

BBC Group

BBC1

BBC2

BBC1

BBC2

BLN1

BLN2

BORD

BR1

SDR

SDR1

SFB1

SFB3

SKY

Berlin 1

Berlin 2

Border TV

Bayern1

Bayern3

BRT1

SFB1

SFB3

SKY

Sky One

Sky Net

Sport

SKY1

SKYN

SPRT

SR1

BR3

BRT1

BRT2

CHLD

CH+

BRT2

SR 1

Children Ch

Canal +

CNN

Super RTL

STV Test

STV 1

STV 2

Suedwest3

SWF 1

Schweiz4

TYNE TEES

Text

SRTL

STVT

STV1

STV2

SWR

SWF1

SWZ4

TEES

TEXT

TF1

CNN

CHNL

CNTR

CH 4

CH 5

DRS

Channel TV

Central TV

Channel 4

Channel 5

DRS

DR TV

DSF

DRTV

DSF

TF1

Euronews

Eurosports

France1

France2

France3

Granada TV

Grampian TV

Hessen1

Hessen3

HRT

EURN

EURO

EURS

FR1

TNT int

TRT int

TSI

TNT

TRT

TSI

TSR

FR2

FR3

TSW

TVE

GRNA

GRMP

HR1

TV Polonia

TVP 1

TVP 2

TVS

TVPA

TVP1

TVP2

TVS

HR3

HRT

TV2

TV5

TV2

TV5

HTV

ITV Network

Kabelkanal

London

MDR

ITV

Tele Zurich

Ulster TV

Veronica

VIVA

TZUR

ULST

VERN

VIVA

VIV2

VOX

VTM

VT4

KABL

LNDN

MDR

MTV

VIVA2

VOX

Nord3

NDR1

NDR3

NED1

NED2

NED3

NET2

NRK

VTM

NDR3

VT4

NED1

West1

West3

YLE 1

WDR1

WDR3

YLE1

YLE2

YORK

ZDF

NED2

NED3

Network 2

NRK

YLE 2

Yorkshire TV

ZDF

N-TV

OKAN

ORF1

ORF2

ORF3

OWL3

PRMI

PR07

RAI1

RAI2

RAI3

RB1

Offener Kanal

ORF1

Zurich 1

3SAT

ZUR1

3SAT

ORF2

ORF3

OWL 3

Premiere

PR07

RAI1

RAI2

RAI3

RB1

RB3

Rikisutvarpid-S

RTBF 1

RTBF 2

RTE 1

RKPS

RTB1

RTB2

RTE1

RTL

RTL2

RTP

RTL

RTL 2

RTP

Download from Www.Somanuals.com. All Manuals Search And Download.

TV Station Channel Number Guide

Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV.

BBC1 BBC2 ITV CH4 CH5

London & South-East

North-West

Caldbeck..............................30

Winter Hill...........................55

Bluebell Hill.........................40

Crystal Palace.......................26

Dover...................................50

Heathfield ............................49

Oxford .................................57

—

North-East

Bilsdale West Moor..............33

Chatton................................39

Pontop Pike..........................58

—

South-West

Beacon Hill..........................57

Caradon Hill ........................22

Huntshaw Cross ...................55

Redruth ................................51

Stockland Hill ......................33

Channel Islands

—

Scotland

Angus...................................57

Black Hill.............................40

Sandale................................22

Caldbeck.............................. —

Creigkelly.............................31

Darvel..................................33

Durris...................................22

Eitshal ..................................33

Keelylang Hill ......................40

Knock More .........................33

Rosemarkie ..........................39

Rumster Forest......................31

Selkirk..................................55

—

Fremont Point.......................51

—

South

Hannington..........................39

Midhurst...............................61

Rowridge..............................31

—

West

Mendip ................................58

East

Wales

Sandy Heath.........................31

Sudbury................................51

Tacolneston..........................62

Blaenplwyf...........................31

Carmel.................................57

Llanddona............................57

Moel-y-Parc..........................52

Presely .................................46

Wenvoe ...............................44

—

Midlands

Ridge Hill.............................22

Sutton Coldfield ...................46

The Wrekin ..........................26

Waltham ..............................58

Northern Ireland

Brougher Mountain..............22

Divis ....................................31

Limavady..............................55

—

North

Belmont ...............................22

Emley Moor..........................44

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

NOTES:

● If you set the unit to a channel which is occupied by a local

station or has neighbouring channels that are occupied by

local stations, the picture reception quality will be affected

and some interference noise will appear on the TV screen. Be

sure to select a vacant channel which has no broadcast on

neighbouring channels.

Video Channel Set

Video channel (RF output channel) is the channel on which your

TV receives picture and sound signals from the unit through the

RF cable.

IMPORTANT

● If you cannot obtain the two vertical white bars clearly with

any channel between 22 and 69, consult your JVC dealer.

Perform the following steps only if —

— Video Channel Set has not been done correctly by the

Auto Set Up function (੬ pg. 12),

— interference appears in the TV picture after you have

moved to a different area or a new station has started

broadcasting in your area.

C ^{Exit the Video Channel Set mode.}

Press ENTER.

— you change the connection between your unit and TV

from RF connection to AV connection, or vice versa.

With AV Connection

To view picture signals from the unit, set your TV to its

AV mode.

If you have connected the unit to your TV via the AV

connection (੬ pg. 11), you have to set the video

channel to off.

If you have connected the unit to your TV via the RF

connection (੬ pg. 11), you have to set the correct

video channel.

With RF Connection

The channel you have set in step B is your video

channel.

To view picture signals from the unit, set your TV to

this video channel.

Before performing the following steps:

● Make sure there is no cassette inserted in the unit.

● Press VCR/DVD on the unit or VCR on the remote control

so that the VCR indicator lights up, then press 1 to turn

off the unit.

A ^{Access the Video Channel Set mode.}

Hold down 8 on the unit until the front display panel

shows the following.

B ^{Set the video channel.}

With AV Connection

Press PR – until the front display panel shows “– –.”

● Now the video channel is set to off.

With RF Connection

Press PR + or – to set the unit to a vacant channel

between 22 and 69 which is not occupied by any local

station in your area.

(Example) If channel 50 is available in your area

Then set your TV to UHF channel 50.

● If the two vertical white bars appear

clearly on the TV screen as shown to

the right, go to step C.

● If the two vertical white bars do not

appear clearly, re-set the unit to

another vacant channel and try again.

Download from Www.Somanuals.com. All Manuals Search And Download.

E ^{Set the date and time.}

Clock Set

Press rt to set the time, then press ENTER or e. The

“DATE” display begins blinking. Repeat the same

procedure to set the date and year.

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

● When you set the time/date, press and hold rt to change the

time by 30 minutes/15 days.

F ^{Set Just Clock.}

Slide to the

right.

The default setting is “ON.” Set as desired by pressing

rt, then press ENTER or e.

● For the Just Clock function, refer to “Just Clock” on page 65.

● If you set it “OFF,” press SET UP to finish the clock setting.

Just Clock

The Just Clock function provides accurate time keeping

through automatic adjustments at regular intervals, by

reading data from a PDC signal.

The Just Clock option can be set “ON” or “OFF” at the Clock

Set screen (the default setting is “ON”). Press ENTER until the

Just Clock setting begins blinking, then press rt to change

the setting.

IMPORTANT: If you turn off Just Clock, the accuracy of the

built-in clock may be reduced, which could adversely effect

timer recording. We recommend you to set Just Clock on. In

cases where the clock setting data from a PDC signal is

incorrect, however, you are advised to set it “OFF.”

IMPORTANT

If you performed Auto Set Up (੬ pg. 12) or Preset

Download (੬ pg. 13), without ever having set the clock

previously, the unit’s built-in clock is also set automatically.

Perform the following steps only if —

—Auto Clock Set has not been performed correctly by Auto

Set Up or Preset Download.

—you want to change the Just Clock setting. (੬ pg. 65, “Just

Clock”)

Set the source channel position for clock

data.

The unit is preset to receive clock setting and adjustment

data from channel position 1.

Press rt to set the channel position to the number

representing the station transmitting clock setting data,

then press ENTER or e.

A ^{Turn on the unit.}

Press 1.

B ^{Select the VHS deck.}

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

H ^{Start the clock operation.}

On the unit

Press SET UP.

NOTES:

On the remote control

Press VCR so that the VCR indicator lights up.

● Just Clock (when set to “ON”) adjusts the unit’s built-in clock

every hour, except for 23:00, 0:00, 1:00 and 2:00.

● Just Clock is not effective when:

— the unit’s power is on.

C ^{Access the Main Menu screen.}

— the unit is in the timer mode. (VHS deck only)

— a difference of more than 3 minutes exists between the

built-in clock’s time and the actual time.

— the unit is in the Automatic Satellite Programme Recording

mode. (੬ pg. 28) (VHS deck only)

— the unit is in the Power Save mode. (੬ pg. 54) (VHS deck

only)

— “L-2 SELECT” is set to “SAT.” (੬ pg. 54) (VHS deck only)

● If Just Clock is set to “ON,” the unit’s clock is automatically

adjusted at the start/end of Summer Time.

● Just Clock may not function properly depending on the

reception condition.

Press SET UP.

D ^{Access the Clock Set screen.}

Press rt to move the highlight bar (pointer) to “CLOCK

SET,” then press ENTER or e. The Clock Set screen

appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

A ^{Set the Child Lock.}

Child Lock

Press and hold 1 on the remote control for more than

10 seconds while the unit is turned on. The unit turns off,

and “CL“ appears on the front display panel.

You can disable the unit’s operation.

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

● To release the child lock, press and hold 1 on the remote

control until the unit turns on.

Slide to the

right.

NOTES:

● When the child lock function is in use, keep the remote

control out of the children’s reach.

● Timer recording programmes will be performed even if the

child lock function is activated.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Before requesting service for a problem, use this chart

and see if you can repair the trouble yourself. Small

problems are often easily corrected, and this can save

you the trouble of sending your unit off for repair.

Noise appears during normal playback.

● The automatic tracking mode is engaged.

]Try manual tracking. (੬ pg. 20)

The playback picture is blurred or interrupted while TV

broadcasts are clear or “USE CLEANING CASSETTE”

message appears on the screen.

Power

No power is supplied to the unit.

● The video heads may be dirty.

● The mains power cord is disconnected.

]Connect the mains power cord.

]Use a dry cleaning cassette ECL-3F, or consult your JVC

dealer.

The remote control won’t function.

Breaks are noticeable in Hi-Fi soundtrack.

● The batteries are discharged.

]Replace the dead batteries with new ones.

● The automatic tracking mode is engaged.

]Try manual tracking. (੬ pg. 20)

Tape Transport (VHS deck)

Playback (DVD deck)

During recording, the tape does not run. “ ” lights up on

the front display panel.

The button does not work.

● The operation is prohibited on the placed disc.

● The unit is in the Record Pause mode.

]Press 4 to resume recording.

The DVD deck can not be operated.

● The DVD deck is not selected.

On the unit

]Press VCR/DVD repeatedly so that the DVD indicator lights

up.

The tape will not rewind or fast-forward.

● The tape is already fully rewound or fast-forwarded.

]Check the cassette.

On the remote control

]Press DVD so that the DVD indicator lights up.

Playback (VHS deck)

“

” appears on the TV screen.

The VHS deck can not be operated.

● The operation is prohibited on the placed disc.

● The VHS deck is not selected.

On the unit

“REGION CODE ERROR!” appears on the TV screen.

]Press VCR/DVD repeatedly so that the VCR indicator lights

up.

● The disc’s region number does not match that of the unit.

]Use the discs whose region number includes “ALL” or “2.”

(੬ pg. 5)

On the remote control

]Press VCR so that the VCR indicator lights up.

The playback picture does not appear while the tape is

running.

The disc cannot be played back.

● The disc’s region number does not match that of the unit.

]Use the discs whose region number includes “ALL” or “2.”

(੬ pg. 5)

● This type of disc cannot be played back.

]See “Unplayable Discs” (੬ pg. 5).

● The disc is not placed properly.

]Remove the disc, then place the disc properly in the disc tray.

(੬ pg. 6, “Placing a Disc”)

● The Parental Lock is engaged, and the placed disc is rated

higher than the set level.

● If you are using the RF connection,

— the TV receiver’s channel selector is not set to the video

channel.

— the unit’s video channel has not been correctly set.

]If you are using the RF connection,

— set the TV receiver to the video channel.

— perform “Video Channel Set” (੬ pg. 64).

● If you are using the AV connection, the TV receiver is not set

to the AV mode.

]If you are using the AV connection, set the TV to its AV mode.

]Release the Parental Lock temporarily (੬ pg. 57), or change

the set level (੬ pg. 57).

Noise appears during visual search.

The language is not played back as you set.

● This is normal.

● The disc does not contain the language you set.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING (cont.)

Recording (VHS deck)

Changing audio/subtitle language is not possible.

● The disc does not contain audio/subtitles in multiple

languages.

]With some discs, the language should be set on the disc

menu. (੬ pg. 31)

Recording cannot be started.

● There is no cassette loaded, or the cassette loaded has had its

record safety tab removed.

]Insert a cassette, or using adhesive tape, cover the hole where

the tab was removed.

The subtitles do not appear on the TV screen.

● The disc does not contain subtitles.

● The subtitle display is set to off.

TV broadcasts cannot be recorded.

● “L-1,” “L-2” or “F-1” has been selected as the input mode.

]Set to the desired channel.

]Set the subtitles display to on. (੬ pg. 34)

● A-B Repeat Playback is in progress. (੬ pg. 33)

]The subtitles recorded around point A-B may not appear.

Tape-to-tape editing is not possible.

Angle cannot be changed.

● The source (another video recorder, camcorder) has not been

properly connected.

● The scene is not recorded from multiple angles.

]Confirm that the source is properly connected.

● All necessary power switches have not been turned on.

]Confirm that all units’ power switches are turned on.

● The input mode is not correct.

Audio/Video Files Playback (DVD deck)

No sound and/or no picture comes out.

]Set the input mode to “L-1,” “L-2” or “F-1.”

● MP3 disc is recorded with the “packet writing (UDF format).”

It cannot be played back.

● Check the files if they are playable or unplayable.

Camcorder recording is not possible.

● The camcorder has not been properly connected.

]Confirm that the camcorder is properly connected.

● The input mode is not correct.

Files (tracks) are not played in the recorded order.

● The unit plays the files in the alphabetic order. So, the

playback order can vary.

]Set the input mode to “L-1,” “L-2” or “F-1.”

“

” and “ ” on the front display panel won’t stop blinking.

DivX files are played back without sound.

● The end of the tape was reached during recording.

]The programme may not have been recorded in its entirety.

Next time make sure you have enough time on the tape to

record the entire programme.

● The unit can play back the MP3 sound for the audio part of

the DivX files. Select the proper audio CODEC when making

DivX files.

Download from Www.Somanuals.com. All Manuals Search And Download.

Timer Recording (VHS deck)