JVC DVD VCR Combo 0105KTH MW BJ User Manual

DVD PLAYER &

VIDEO CASSETTE RECORDER

HR-XV38SAG

HR-XV38SAS

INSTRUCTIONS

LPT1016-001A

Download from Www.Somanuals.com. All Manuals Search And Download.

POWER SYSTEM:

This set operates on voltage of AC110 – 240 V~ (Rating), AC90

– 260 V ~ (Operating), 50Hz/60Hz with automatic switching.

Contents

SAFETY FIRST

The 1 button does not completely shut off mains power from

the unit, but switches operating current on and off. “`” shows

electrical power standby and “!” shows ON.

Safety Precautions ....................................................................2

DISC INFORMATION

About Discs .............................................................................4

The socket outlet shall be installed near the equipment and

easily accessible, or the mains plug or an appliance couplar

shall remain readily operable.

INDEX

INSTALLING YOUR NEW UNIT

Video tapes recorded with this unit in the LP (Long Play) or EP

(Extended Play) mode cannot be played back on a single-speed

video recorder. (VHS deck only)

Basic Connections ...................................................................9

Component Video Connection (DVD deck) ...........................10

Scan Mode Set (DVD deck) ....................................................11

S-VIDEO Connection (DVD deck) ..........................................12

When the equipment is installed in a cabinet or a shelf, make

sure that it has sufficient space on all sides to allow for ventilation

(10 cm or more on both sides, on top and at the rear.)

INITIAL SETTINGS

Video Channel Set .................................................................13

Auto Set Up ...........................................................................14

Monitor Set (DVD deck) .........................................................15

Language ...............................................................................16

Clock Set ...............................................................................19

When discarding batteries, environmental problems must be

considered and the local rules or laws governing the disposal of

these batteries must be followed strictly.

OPERATIONS ON VHS DECK

Failure to heed the following precautions may result in

damage to the unit, remote control or video cassette.

1. DO NOT place the unit —

Basic Playback .......................................................................20

Playback Features ..................................................................21

Basic Recording .....................................................................23

Recording Features ................................................................24

B.E.S.T. Picture System ...........................................................25

G-CODE^®/SHOWVIEW^TMSystem Setup ........................................26

G-CODE^®/SHOWVIEW^TMTimer Programming ..............................27

Express Timer Programming ...................................................29

Automatic Satellite Programme Recording .............................32

— in an environment prone to extreme temperatures or

humidity.

— in direct sunlight.

— in a dusty environment.

— in an environment where strong magnetic fields are

generated.

— on a surface that is unstable or subject to vibration.

2. DO NOT block the unit’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a

newspaper or cloth, etc., the heat may not be able to get out.)

3. DO NOT place heavy objects on the unit or remote control.

4. DO NOT place anything which might spill on top of the unit

or remote control.

(If water or liquid is allowed to enter this equipment, fire or

electric shock may be caused.)

5. DO NOT expose the apparatus to dripping or splashing.

6. DO NOT use this equipment in a bathroom or places with

water. Also DO NOT place any containers filled with water or

liquids (such as cosmetics or medicines, flower vases, potted

plants, cups, etc.) on top of this unit.

OPERATIONS ON DVD DECK

Basic Playback .......................................................................33

Playback Features ..................................................................34

Using the on-screen bar .........................................................40

MP3/JPEG files Playback ........................................................42

EDITING (VHS DECK)

Edit From A Camcorder ..........................................................45

Edit To Or From Another Video Recorder ..............................46

Dubbing (from DVD to VHS) .................................................47

EDITING (DVD DECK)

Digital Audio Dubbing ...........................................................48

REMOTE CONTROL

Remote Control Functions ......................................................49

7. DO NOT place any naked flame sources, such as lighted

candles, on the apparatus.

8. AVOID violent shocks to the unit during transport.

SYSTEM CONNECTIONS

Connecting To A Satellite Receiver ........................................51

Connecting To A Dolby Digital Decoder or An Amplifier With A

Built-in DTS (DVD deck) ........................................................52

MOISTURE CONDENSATION

Moisture in the air will condense on the unit when you move it

from a cold place to a warm place, or under extremely humid

conditions—just as water droplets form on the surface of a glass

filled with cold liquid. Moisture condensation on the head drum

will cause damage to the tape. In conditions where condensation

may occur, keep the unit turned on for a few hours to let the

moisture dry.

SUBSIDIARY SETTINGS

Function Set (VHS deck) ........................................................53

Mode Set (DVD deck) ............................................................56

Tuner Set ...............................................................................60

Information on Multi-System Compatibility (VHS deck) .........65

TROUBLESHOOTING

SPECIFICATIONS

LIST OF TERMS

ATTENTION

To mobile phone user:

Using a mobile phone in the vicinity of the unit may cause

picture vibration on the TV screen or change the screen to a

blue back display.

On placing the unit:

Some TVs or other appliances generate strong magnetic fields.

Do not place such appliances on top of the unit as it may cause

picture disturbance.

Download from Www.Somanuals.com. All Manuals Search And Download.

DISC INFORMATION

Region Number

About Discs

The world is divided into 6 regions for DVD VIDEO discs. DVD

VIDEO discs are assigned a region number to indicate which

region they may be played back in. A disc cannot be played

back on your unit unless the region number of the disc matches

the one on the rear of your unit. The region number for your unit

is as follows:

Playable Discs

You can use discs with the following logos for playback only.

DVD VIDEO

Video CD/Super Video CD

HR-XV38SAG: “3”

Examples of DVD VIDEO labels which can be played back with

HR-XV38SAG.

Audio CD

CD-DA files

HR-XV38SAS: “2”

Examples of DVD VIDEO labels which can be played back with

HR-XV38SAS.

● The following discs also can be played back.

• DVD-R/-RW discs recorded in DVD VIDEO format and

finalized.

• CD-R/RW discs recorded in Video CD, SVCD (Super Video

CD), or Audio CD format and finalized.

• CD-R/RW discs written in MP3 or JPEG in accordance with

the “ISO 9660” format. (See page 42 for details.)

● This unit can also play back audio signals recorded in MIX-

MODE CD, CD-G, CD-EXTRA, and CD TEXT.

● The image may be sometimes poor or noisy due to defects in

the disc itself.

DVD VIDEO Marks

Sometimes marks are printed on a DVD disc and/or on its

packaging to indicate information regarding the contents and

functions of a disc. Check marks indicating the contents and

functions of a disc. Note, however, that in some cases a disc may

not include a mark even for a function it supports.

● With some discs, operations may not be possible.

Marks of discs in this instruction manual

Marks related to video

Allows operation with a

DVD VIDEO disc.

Allows operation with a

Video CD disc.

Number of subtitles

Number of angles

Allows operation with a

SVCD disc.

Allows operation with

an Audio CD disc.

Recorded under the

standard 4:3 aspect

ratio

Screen includes black

bands at top and

bottom of image

which has a standard

4:3 aspect ratio (letter

box)

Unplayable Discs

The following types of discs cannot be played using this unit.

● CD-ROM discs (including PHOTO-CD)

● DVD AUDIO discs

Video playback is in Wide video mode (16:9) on

wide televisions, but in letter box on televisions

with standard 4:3 aspect ratio.

● Super Audio CDs (SACD)

● DVD-RW discs recorded in VR format

● DVD-RAM discs

● DVD-ROM discs

Video playback is in Wide video mode (16:9) on

wide televisions, but pan and scan is used on

televisions with standard 4:3 aspect ratio (either

the left or right side of the image is cut-out).

In addition, this unit does not play:

● Unfinalized discs

● Discs of irregular shape or discs with tape, seals, or paste on

either the label side or playback side. Playing back these discs

may damage the unit.

Marks related to audio

The Non-DVD side of a “DualDisc” does not comply with the

“Compact Disc Digital Audio” standard. Therefore, the use of

Non-DVD side of a DualDisc on this product may not be

recommended.

Number of audio tracks

Dolby Digital mark

Dolby Laboratories has developed a digital

surround system for the home. This mark

indicates that you may enjoy 5.1-channel

audio (front left and right, center, rear left and

right, and a channel for LFE (Low-Frequency

Effects)).

DTS (Digital Theater System)

You can enjoy DTS audio if you connect an

amplifier with a built-in DTS decoder to the

DIGITAL AUDIO OUT connector of the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

File Structure of Discs

Care and Handling of Discs

DVD VIDEO

How to handle discs

Typically, DVD VIDEO discs are made up of larger units called

“titles.” Each title has a number (title number) that can be used to

select desired titles. Titles are further divided into units called

“chapters.” Each chapter has a number (chapter number) that

can also be used to select desired chapters. Note that some discs

are not divided into titles and chapters.

When handling a disc, do not

touch the surface of the disc.

Since discs are made of

plastic, they are easily

damaged. If a disc gets dirty,

dusty, scratched or warped,

the images and sound will not

be picked up correctly, and such a disc may cause the unit to

malfunction.

Title1

Title2

Chapter 2

Chapter 3

Chapter 1

Chapter 2

Label side

Do not damage the label side, stick paper to or use any adhesive

on its surface.

Storage

Audio CD/Video CD

Make sure that discs are kept in their cases. If discs are piled on

top of one another without their protective cases, they can be

damaged. Do not put discs in a location where they may be

exposed to direct sunlight, or in a place where the humidity or

temperature is high. Avoid leaving discs in your car!

Typically, Audio CD discs are divided into separate tracks each

containing one song. Each track is assigned a number. For

example, the third track is Track 3. The same is true for Video

CD discs.

Track 1

Track 2

Track 3

Track 4

Maintenance of discs

If there are fingerprints or other dirt adhering

to a disc, wipe with a soft dry cloth, moving

from the center outwards.

If a disc is difficult to clean, wipe with a

cloth moistened with water. Never use

record cleaners, petrol, alcohol or any anti-

static agents.

NOTE:

Video CD discs that support Playback Control (PBC)

The still image or motion image which follows a menu screen is

called a “scene.” Each scene has a scene number.

For more details, refer to “Locating a Desired Scene Using the

Menu of the Video CD with Playback Control (PBC) Function”

(੬ pg. 34).

CAUTION

Sometimes during playback, noise or images may be garbled.

This is sometimes due to the disc. (It may not be up to

industry standards.)

Placing a Disc

1 Open the disc tray.

These symptoms are caused by the discs, not by the

malfunction of the unit.

Press x on the DVD deck to open the disc tray.

● The unit’s power comes on

automatically.

● Do not block the disc tray with

your hand while it is opening or

closing as this may result in

hardware failure.

● Do not place unplayable discs or

any object other than a disc in

the disc tray.

● Do not press down strongly on the disc tray or place any heavy

objects on it.

2 Place the disc.

Place the disc in the disc tray with

the label side facing up.

● Since disc size changes depending on

the disc to be played back, be sure to

correctly align the disc with the

grooves for its size. If the disc is not in

its groove, it may be scratched or

otherwise damaged.

● To insert an 8 cm disc, place it according to the inner groove.

3 Press x on the DVD deck to close the disc tray.

● Pressing 4 also closes the disc tray.

● Playback begins automatically if an auto-playback DVD disc is

loaded. Although the VHS deck is selected, the DVD deck is

selected automatically (except when the VHS deck is in the

timer mode or the Automatic Satellite Programme Recording

mode.)

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX

FRONT VIEW

SCAN MODE

A STANDBY/ON Button (1) ੬ pg. 11, 14, 21, 49

B VCR Indicator ੬ pg. 20, 23

M Front Display Panel ੬ pg. 7

N Record Button (7) ੬ pg. 23, 24

C Cassette Loading Slot

O Rewind Button (3) ੬ pg. 20, 21, 35

P Fast Forward Button (5) ੬ pg. 20, 21, 35

Q Programme Button (PR +/–) (੬ pg. 21, 23, 29

R SCAN MODE Button ੬ pg. 11

D VCR/DVD Button ੬ pg. 20, 23, 33, 43

E Disc Tray ੬ pg. 5

F DVD Indicator ੬ pg. 33

G Stop Button (8) ੬ pg. 20, 23, 33, 43

H Play Button (4) ੬ pg. 20, 23, 33, 43, 49

I DVD Open/Close Button (x) ੬ pg. 5, 33, 43

J Cassette Eject Button (x) ੬ pg. 20, 21, 23

K Video/Audio Input Connectors (F-1 VIDEO/AUDIO)

੬ pg. 45

To access covered

connectors or buttons, pull

and open the cover.

L Infrared Beam Receiving Window

REAR VIEW

INPUT

(L-1)

S VIDEO

VIDEO

AUDIO

VIDEO

AUDIO

DVD

AUDIO

OUTPUT

COMPONENT

VIDEO OUT

OUTPUT

DVD/VCR

DVD

A Region Number Label ੬ pg. 4

B Mains Power Cord ੬ pg. 9, 10, 12

C S-Video Output Connector

(S-VIDEO OUTPUT)* ੬ pg. 12, 51

D Audio/Video Output Connector

(AUDIO/VIDEO OUTPUT) ੬ pg. 9, 10, 12, 46, 51

E L-1 Input Connector (INPUT (L-1)) ੬ pg. 9, 46, 51

F Antenna Input Connector (ANTENNA IN) ੬ pg. 9,

10, 12, 51

G Digital Audio Output Connector

(DIGITAL AUDIO OUT)* ੬ pg. 48, 52

H Component Video Output Connectors

(COMPONENT VIDEO OUT)* ੬ pg. 10

I Audio Output Connectors (AUDIO OUT (L/R))*

J Remote Pause Connector (PAUSE) ੬ pg. 45

Antenna Output Connector (ANTENNA OUT)

pg. 9, 10, 12, 51

੬

* These connectors are only for DVD deck.

Download from Www.Somanuals.com. All Manuals Search And Download.

FRONT DISPLAY PANEL

C DE

C Progressive Mode Indicator ੬ pg. 11

D “Timer ” Indicator ੬ pg. 28, 29, 32

A Operation Mode Indicator

B Channel/Clock Display

Mode Display (L-1 or F-1)

Counter Display

E Satellite Auto Recording Indicator (N) ੬ pg. 32

Tape Speed (SP/LP or EP*) ੬ pg. 23

* EP is for NTSC only.

Multi-information window*

* The current group/title/track/chapter number(s), time and status

information.

ON-SCREEN DISPLAY (VHS deck)

If you press – –:– – on the remote control when “O.S.D.”

is set to “ON” (੬ pg. 54), various operational indicators

appear on the TV screen.

H Audio Mode Display ੬ pg. 22

I Tape Speed (SP/LP or EP*)

* EP is for NTSC only.

For On-screen display for DVD deck, refer to “Using the

on-screen bar” (੬ pg. 40).

J Colour System Indicator ੬ pg. 54

K Tape Direction

L Counter Display

M Tape Remaining Time Indicator ੬ pg. 24

A “Cassette Loaded” Mark

B Operation Mode Indicators

C Channel Position Number and Station Name/Auxiliary

Input Indicator (L-1 or F-1)

D Clock Display

E Current Day/Month/Year

F Type of Broadcast ੬ pg. 25

G Tape Position Indicator

The tape position indicator

appears on the TV screen

when you press 3 or

5 from the Stop mode or

perform an Index Search.

(੬ pg. 21) The position of

“q” in relation to “0”

(beginning) or “+” (end)

shows you where you are

on the tape.

Beginning

End

NOTE:

Depending on the type of tape being used, the tape position

indicator may not appear correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX (cont.)

A TV Standby/On Button (TV 1) ੬ pg. 50

B TV/VCR/DVD switch ੬ pg. 11, 13-16, 19, 20, 33, 43,

C DVD Button ੬ pg. 11, 15, 33, 43, 56

D VCR Button ੬ pg. 14, 16, 19, 20, 53

E Number Keys

F Daily Button (DAILY) ੬ pg. 28, 29, 31

G VPS/PDC Button

REMOTE CONTROL

*Does not function with this unit.

H Reset Button (0000) ੬ pg. 24

Cancel Button (&) ੬ pg. 27, 30, 31

I Auxiliary Button (AUX) ੬ pg. 45

J Start Time Button (START +/–) ੬ pg. 29

Repeat Button (REPEAT) ੬ pg. 36, 44

Zooming Button (ZOOM) ੬ pg. 35, 44

K Stop Time Button (STOP +/–) ੬ pg. 28, 29, 30, 31

On Screen Button (ON SCREEN) ੬ pg. 40

L Programming Button (PROG) ੬ pg. 27, 29, 31

M Tape Speed Button SP/LP or EP* (p) ੬ pg. 23, 27,

29, 30, 31

* EP is for NTSC only.

Top Menu Button (TOP MENU) ੬ pg. 34

N Programme Check Button (") ੬ pg. 30

Return Button (RETURN) ੬ pg. 34

O w e Button

rt Button

ENTER Button

VCR Programme Button (VCR PR +/–)

P Set Up Menu Button (SET UP) ੬ pg. 15, 19, 53, 56,

Q Play Button (4) ੬ pg. 20, 23, 33, 43

R Rewind Button (3) ੬ pg. 20, 21, 35

S Record Button (7) ੬ pg. 23, 24

T Forward Skip/Index Button (6) ੬ pg. 21, 34, 35

U Reverse Skip/Index Button (2) ੬ pg. 21, 34, 35

Review Button (

) ੬ pg. 22

V DVD Picture Button (DVD PICTURE) ੬ pg. 39

W Sound Effect Button (SOUND EFFECT) ੬ pg. 39

X Standby/On Button (1) ੬ pg. 11, 14, 21

Y TV Muting Button ( ) ੬ pg. 50

Audio Monitor Button (A.MONITOR) ੬ pg. 22, 38

Z TV/VCR Button ੬ pg. 24, 50

Buttons with a small dot on the left side of the name can also

be used to operate your JVC TV. (੬ pg. 50)

a TV Volume Button (TV %+/–) ੬ pg. 50

b Weekly Button (WEEKLY) ੬ pg. 28, 29, 31

c TV Programme Button (TV PR +/–) ੬ pg. 50

d Programme Button (PR +/–) ੬ pg. 21, 23, 29, 30, 31

e Date Button (DATE +/–) ੬ pg. 29, 30, 31

Subtitle Button (SUBTITLE) ੬ pg. 37

How To Use

The remote control can operate most of your unit’s functions,

as well as basic functions of TV sets of JVC. (੬ pg. 49)

● Point the remote control toward the receiving window.

● The maximum operating distance of the remote control is

about 8 m.

Angle Button (ANGLE) ੬ pg. 38

f Timer Button (#) ੬ pg. 28, 29, 30

g Menu Button (MENU) ੬ pg. 34

h Automatic Satellite Programming Button (REC LINK)

੬ pg. 32

NOTES:

● When inserting the batteries, be sure to insert in the correct

directions as indicated under the battery cover.

● If the remote control doesn’t work properly, remove its

batteries, wait a short time, replace the batteries and then try

again.

i Display Button (– –:– –) ੬ pg. 24, 33

j Fast Forward Button (5) ੬ pg. 20, 21, 35

k Stop/Clear Button (8) ੬ pg. 20, 23, 33, 43

l Pause Button (9) ੬ pg. 21, 23, 33, 35, 43

m One Touch Replay Button ( ) ੬ pg. 21, 35

n Skip Search Button ( ) ੬ pg. 21

o Tracking Button (TRACKING +/–) ੬ pg. 22

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING YOUR NEW UNIT

It’s essential that your unit be properly connected.

Basic Connections

THESE STEPS MUST BE COMPLETED BEFORE ANY

VIDEO OPERATION CAN BE PERFORMED.

A ^{Check the contents.}

TV aerial cable

Mains outlet

Make sure the package contains all of the accessories

listed in “SPECIFICATIONS” on page 70.

AUDIO/VIDEO OUTPUT

B ^{Situate the unit.}

Mains power cord

Place the unit on a stable, horizontal surface.

INPUT

(L-1)

VIDEO

C ^{Connect the unit to TV.}

VIDEO

AUDIO

VIDEO

AUDIO

DVD

AUDIO

The connection method you use depends on the type of

TV you have.

OUTPUT

COMPONENT

VIDEO OUT

DVD

OUTPUT

DVD/VCR

Back of unit

RF Connection

ANTENNA IN

8To connect to a TV with NO AV input connectors —

A Disconnect the TV aerial cable from the TV.

B Connect the TV aerial cable to the ANTENNA IN

connector on the rear panel of the unit.

C Connect the provided RF cable between the

ANTENNA OUT connector on the rear panel of the

unit and the TV’s aerial connector.

ANTENNA OUT

To AV input

connectors

AV Connection

8To connect to a TV with AV input connectors —

If your TV is equipped with a AV input connectors,

perform AV connection to improve picture quality during

tape playback.

To aerial terminal

(provided)

A Connect the aerial, unit and TV as per “RF

Connection.”

B Connect an optional AV cable between the AUDIO/

VIDEO OUT connectors on the rear panel of the unit

and the TV’s AV input connectors.

D ^{Connect the unit to mains.}

Plug the end of the mains power cord into a mains outlet.

After the connection is completed, perform “Video

Channel Set” on page 13.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING YOUR NEW UNIT (cont.)

Component Video Connection

(DVD deck)

ATTENTION

Be sure to connect the unit’s VIDEO OUT or S VIDEO OUT connector to the TV’s VIDEO IN or S-VIDEO IN connector.

AUDIO IN connectors

Back of TV

S Video cable

(not provided)

COMPONENT VIDEO IN connector

Audio cable

(not provided)

TV aerial

cable

Component Video cable

(not provided)

Aerial connector

Mains outlet

Mains

power cord

INPUT

(L-1)

S VIDEO

VIDEO

AUDIO

VIDEO

AUDIO

DVD

AUDIO

OUTPUT

COMPONENT

VIDEO OUT

OUTPUT

DVD/VCR

DVD

Back of unit

AUDIO OUT

COMPONENT

VIDEO OUT

RF cable (provided)

8To connect to a TV with COMPONENT VIDEO IN

connectors . . .

NOTES:

● You can obtain high-quality component video pictures.

● If your TV is not stereo-capable, use the unit’s AUDIO OUT

connectors to connect to an audio amplifier for Hi-Fi stereo

sound reproduction.

A ^{Connect the unit to TV.}

● For switching the TV’s mode, refer to the instruction manual of

your television.

● By using the component video connection, you can view the

images in the progressive mode. For switching to the

progressive mode, refer to “Scan Mode Set (DVD deck)”

(੬ pg. 11).

Connect the aerial, unit and TV as per “AV

Connection” or “S-VIDEO Connection”. (੬ pg. 12,13)

B Connect the unit’s COMPONENT VIDEO OUT

connectors to the TV’s COMPONENT VIDEO IN

connectors.

C Connect the unit’s AUDIO OUT connectors to the

TV’s AUDIO IN connectors.

After the connection is completed, perform “Video

Channel Set” on page 13.

B ^{Connect the unit to mains.}

Plug the end of the mains power cord into a mains outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

A ^{Turn on the unit.}

Scan Mode Set

Press 1.

(DVD deck)

This unit supports the progressive scan system (eg. 480p*)

as well as the conventional interlaced scan system (eg.

480i*).

B ^{Select the DVD deck.}

On the unit

If your TV equipped with component video connectors

supports the progressive video input, you can enjoy a

high quality picture by setting the progressive scan mode

to active.

● Refer also to the instruction manuals supplied with your TV.

● If your TV equipped with component video connectors does

not support the progressive video input, do not change the

scan mode to the “PROGRESSIVE.”

* 480p and 480i indicate the number of scanning lines and

scanning format of an image signal.

• 480p indicates 480 scanning lines with progressive format.

• 480i indicates 480 scanning lines with interlaced format.

Press VCR/DVD repeatedly so that the DVD indicator

lights up.

On the Remote

Press DVD so that the DVD indicator lights up.

C ^{Switch the mode.}

A Press and hold SCAN MODE on the unit for more than

3 seconds.

The current scan mode blinks on the front display

panel.

B While the current scan mode blinks, press w e to

select “ProGr” (for the progressive scan mode) or

“IntEr” (for the interlaced scan mode), then press

ENTER.

● Turn on the TV and select the VCR channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the Remote to the

right.

• If the current scan mode stops blinking before you make

the setting, start from step A again.

NOTE:

When the progressive scan mode is selected, the Progressive

mode indicator ( ) lights up on the front display panel.

SCAN MODE

Slide to the

right.

Slide to the

right.

DVD

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLING YOUR NEW UNIT (cont.)

S-VIDEO Connection

(DVD deck)

AUDIO IN connectors

Back of TV

S-Video cable

(not provided)

S-VIDEO IN

connector

Audio cable

(not provided)

Aerial connector

Mains outlet

TV aerial

cable

S VIDEO

OUT

Mains

power cord

INPUT

(L-1)

S VIDEO

VIDEO

AUDIO

VIDEO

AUDIO

DVD

AUDIO

OUTPUT

COMPONENT

VIDEO OUT

OUTPUT

DVD/VCR

DVD

Back of unit

AUDIO OUT

RF cable (provided)

8To connect to a TV with S-VIDEO/AUDIO IN

connectors . . .

NOTES:

● You can obtain high-quality S-VHS pictures.

● If your TV is not stereo-capable, use the unit’s AUDIO OUT

connectors to connect to an audio amplifier for Hi-Fi stereo

sound reproduction.

● For switching the TV’s mode, refer to the instruction manual of

your television.

A ^{Connect the unit to TV.}

A Connect the aerial, unit and TV as per “RF

Connection”. (੬ pg. 13)

B Connect the unit’s S VIDEO OUT connector to the

TV’s S-VIDEO IN connector.

C Connect the unit’s AUDIO OUT connectors to the

TV’s AUDIO IN connectors.

After the connection is completed, perform “Video

Channel Set” on page 13.

B ^{Connect the unit to mains.}

Plug the end of the mains power cord into a mains outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SETTINGS

C ^{Set the video channel.}

With AV Connection

Video Channel Set

Video channel (RF output channel) is the channel on which your

TV receives picture and sound signals from the unit through the

RF cable.

Press ENTER, then press PR – until the front display panel

shows “– –”.

Before performing the following steps:

● Make sure there is no cassette inserted in the unit and the

power is off.

● Slide the TV/VCR/DVD switch on the remote control to the

right.

● Now the video channel is set to off.

With RF Connection

Set your TV to UHF channel 36.

● If the two vertical white bars appear

clearly on the TV screen as shown on

the right, press ENTER and then go to

step D.

A ^{Access the Video Channel Set mode.}

shows the following.

Hold down 8 on the unit until the front display panel

● If the two vertical white bars do not

appear clearly, press ENTER and then

PR + or – to set the unit to a vacant channel between 28 and

60 which is not occupied by any local station in your area.

(Example) If channel 50 is available in your area

B ^{Set the TV system (RF Connection only)}

Press PR + or – on the remote control to set the

appropriate TV system that matches the system of TV

being used (refer to the table below).

Then set your TV to UHF channel 50 and check if the two

vertical white bars appear clearly on the TV screen ; if so, go to

step D. If not, re-set the unit to another vacant channel and try

again.

NOTES:

1:B/G 2:D/K 3:I 4:H

● If you set the unit to a channel which is occupied by a local

station or has neighbouring channels that are occupied by

local stations, the picture reception quality will be affected

and some interference noise will appear on the TV screen. Be

sure to select a vacant channel which has no broadcast on

neighbouring channels.

Major Countries/Areas

TV System

New Zealand, Kuwait, U.A.E.,

Indonesia, Singapore, Thailand,

Malaysia, Iran, Saudi Arabia, Egypt,

Morocco, Lebanon, Iraq

B/G

● If you cannot obtain the two vertical white bars clearly with

any channel between 28 and 60, consult your JVC dealer.

China, Mongolia, Russia

Hong Kong

D/K

Australia

D ^{Exit the Video Channel Set mode.}

Press ENTER on the remote control.

● If Auto Set Up (੬ pg. 14) or Tuner Set (੬ pg. 60) has not

previously been performed, the Clock Set screen appears and

Auto Set Up takes place automatically.

With AV Connection

To view picture signals from the unit, set your TV to its

AV mode.

With RF Connection

The channel you have set in step C above is your

video channel.

To view picture signals from the unit, set your TV to

the video channel.

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SETTINGS (cont.)

D ^{Select the TV system.}

system (refer to the table below).

Auto Set Up

Press rt to place the pointer next to the appropriate TV

The Auto Set Up simplifies installation by guiding you

through the procedures of setting the clock and tuner

channels – simply follow the on-screen menus that appear.

Major Countries/Areas

TV System

Australia, New Zealand, Kuwait,

U.A.E., Indonesia, Singapore,

Thailand, Malaysia, Iran, Saudi Arabia,

Egypt, Morocco, Lebanon, Iraq

B/G

Slide to the

right.

China, Mongolia, Russia

Hong Kong

D/K

E ^{Start Auto Channel Set.}

Press ENTER or e.

DO NOT press any button on the unit or remote

control while Auto Set Up is in progress.

Auto Channel Set is performed next. Auto Channel Set scans

all the channels that are receivable by your unit. During Auto

Channel Set, the channel numbers are displayed as they are

scanned and set.

● As Auto Set Up progresses, the

“q” mark on the TV screen

moves from left to right.

● When Auto Set Up is

completed, the lowest position

number will appear on the front

display panel. If “SCAN

COMPLETED -NO SIGNAL-” is

diplayed on the TV screen,

make sure that the aerial cable

AUTO CH SET

PLEASE WAIT

Before starting, make sure of the following:

● The TV aerial cable should be connected to the unit.

● The unit’s mains power cord should be connected to a

mains outlet.

START

FINISH

❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ – – – – – – –

● The “Video Channel Set“ (੬ pg. 13) should be performed

and the TV should be set to its AV mode (with AV

connection ੬ pg. 9) or UHF channel (with RF connection

੬ pg. 9).

● Slide the TV/VCR/DVD switch on the remote control to the

right.

is connected to the unit properly and press ENTER on the

remote control. The unit will try Auto Set Up again.

NOTES:

● If there is a power cut, or if you press 1 or SET UP while Auto

Set Up is in progress, Auto Set Up will be interrupted; be sure

to turn off the unit power once and try again from step A.

● If no sound accompanies the picture or the audio sounds

unnatural on some channels that have been stored by Auto Set

Up, the TV system setting for those channels may be incorrect.

Select the appropriate TV system for those channels.

“TV System Selection — When you see the picture but the

audio can’t be heard or sounds unnatural” ੬ pg. 63).

A ^{Turn on the unit.}

Press 1 on the unit or remote control. The Language

Select screen appears on the TV screen.

B ^{Select language}

ATTENTION

If you perform Auto Set Up successfully during installation,

there’s no need to separately perform the Clock Set or

Channel Set procedures, but if adjustments become

necessary, they can be performed as follows:

● Tuner setting ੬ pg. 60

Press rt to place the pointer next to your desired

language (English, Russian or Arabic), then press ENTER

or e.

● The Clock Set screen appears.

● Clock setting ੬ pg. 19

C ^{Set the date and time.}

Press rt to set the time,

then press ENTER or e. The

“DATE” display begins

blinking. Repeat the same

procedure to set the date and

year.

● When you set the time/date,

press and hold rt to change

the time by 30 minutes/15

days.

Download from Www.Somanuals.com. All Manuals Search And Download.

D ^{Select the mode.}

Monitor Set (DVD deck)

You can select the monitor type depending on the TV

used when you play back DVD VIDEO discs recorded for

wide-screen TVs.

Press rt to move H to “MONITOR TYPE,” then press

ENTER.

For the multi colour system TV

E ^{Select the mode setting.}

When you use a multi colour system TV, you can change

the colour system of this unit automatically by selecting

“MULTI” options as the monitor type. In this case, the

setting of this unit is changed to match the colour system

of the loaded disc regardless the TV system setting.

(੬ “ATTENTION” below)

Press rt to select the desired setting, then press ENTER.

F ^{Return to the normal screen.}

Press SET UP.

* The default setting is bold in the table below.

ATTENTION

How to change the TV system between PAL and NTSC

8 MONITOR TYPE

A Press and hold SCAN MODE on the unit for more

than 3 seconds while the unit is turned off.

The current TV system blinks on the front display

panel.

B While the current TV system blinks, press w e to

select “ntSc” (for NTSC) or “PAL” (for PAL), then

press ENTER.

16:9 NORMAL / 16:9 MULTI NORMAL

(Wide television conversion):

Select this when the aspect ratio of your TV is fixed to 16:9

(wide TV). The unit automatically adjusts the screen width of

the output signal correctly when playing back a picture

whose aspect ratio is 4:3.

16:9 AUTO / 16:9 MULTI AUTO

(Wide television conversion):

Select this when the aspect ratio of your TV is 16:9 (wide

TV).

• If the current TV system stops blinking before you

make the setting, start from step A again.

4:3 LB / 4:3 MULTI LB (Letter Box conversion):

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Select this when the aspect ratio of your TV is 4:3

(conventional TV). While viewing a wide screen picture, the

black bars appear on the top and the bottom of the screen.

4:3 PS / 4:3 MULTI PS (Pan&Scan):

Select this when the aspect ratio of your TV is 4:3

(conventional TV). While viewing a wide screen picture, the

black bars do not appear; however, the left and right edges

of the pictures will not be shown on the screen.

Slide to the

right.

Pan&Scan/Letter Box

In general, DVD VIDEO disc are produced for a wide-screen

TV with 16:9 aspect ratio.

Material with this ratio will not fit to a TV with 4:3 aspect

ratio. There are two styles to display the image, “Pan&Scan”

and “Letter Box.”

Pan&Scan

The right and left side of the image are

cut off. The image fills the screen.

A ^{Turn on the unit.}

Press 1.

Letter Box

Black bands appear at the top and

bottom of the image. The image itself

appears in 16:9 aspect ratio.

B ^{Select the DVD deck.}

Press VCR/DVD repeatedly so that the DVD indicator

lights up.

On the unit

NOTES:

On the remote control

● Even if ”4:3 PS” or ”4:3 MULTI PS” is selected, the screen size

may become ”4:3 LB” or ”4:3 MULTI LB” with some DVD

VIDEO. This depends on how they are recorded.

● When you select ”16:9 NORMAL”or ”16:9 MULTI NORMAL”

for a picture whose aspect ratio is 4:3, the picture slightly

changes due to the process for converting the picture width.

Press DVD so that the DVD indicator lights up.

C ^{Access the DVD Set Up menu screen.}

A Press SET UP.

PICTURE

MONITOR TYPE

PICTURE SOURCE

SCREEN SAVER

4:3LB

AUTO

B Press w e to select

“

PICTURE.”

MP3

MP3 / JPEG

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SETTINGS (cont.)

On-screen Language Set (VHS deck)

Language

A ^{Turn on the unit.}

● Turn on the TV and select the video channel (or AV

mode).

Press 1.

● Slide the TV/VCR/DVD switch on the remote

control to the right.

B ^{Select the VHS deck.}

Press VCR/DVD repeatedly so that the VCR indicator

On the unit

Slide to the

right.

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

C ^{Access the Main Menu screen.}

A Press SET UP.

B Press rt to move the

highlight bar (pointer) to

“INITIAL SET,” then press

ENTER or e.

D ^{Select your country.}

Press rt to move the highlight bar (pointer) to

“LANGUAGE,” then press ENTER or e.

E ^{Select the language.}

Press rt to move the

highlight bar (pointer) to the

language of your choice

(English, Russian or Arabic).

F ^{Return to the normal screen.}

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

On-screen Language Set (DVD deck)

Menu/Audio/Subtitle Language Set

This DVD deck offers you the choice to view on-screen

messages in 3 different languages. You can change the

language setting manually as required.

Some DVD discs contain the DVD menu display, audio,

subtitle in multiple languages. With these discs, you can

set the default language as you like.

● The procedure shows how to set “MENU LANGUAGE”

on the DVD menu screen as an example.

A ^{Turn on the unit.}

Press 1.

A ^{Turn on the unit.}

Press 1.

B ^{Select the DVD deck.}

On the unit

B ^{Select the DVD deck.}

Press VCR/DVD repeatedly so that the DVD indicator

lights up.

On the unit

Press VCR/DVD repeatedly so that the DVD indicator

On the remote control

Press DVD so that the DVD indicator lights up.

lights up.

On the remote control

Press DVD so that the DVD indicator lights up.

C ^{Access the DVD Set Up menu screen.}

A Press SET UP.

LANGUAGE

C ^{Access the DVD Set Up menu screen.}

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ENGLISH

B Press w e to select

“

LANGUAGE.”

A Press SET UP.

LANGUAGE

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ENGLISH

ON SCREEN LANGUAGE ENGLISH

B Press w e to select

“

LANGUAGE.”

ON SCREEN LANGUAGE ENGLISH

D ^{Select the mode.}

Press rt to move H to “ON

SCREEN LANGUAGE,” then

press ENTER.

LANGUAGE

MENU LANGUAGE

D ^{Select the mode.}

ENGLISH

AUDIO LANGUAGE

SUBTITLE

Press rt to move H to

“MENU LANGUAGE,” then

press ENTER.

LANGUAGE

MENU LANGUAGE

ENGLISH

ON SCREEN LANGUAGE ENGLISH

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE ENGLISH

E ^{Select the mode setting.}

Press rt to select the desired setting, then press ENTER.

E ^{Select the mode setting.}

Press rt to select the desired setting, then press ENTER.

● See “Language Code List” (੬ pg. 18).

F ^{Return to the normal screen.}

Press SET UP.

F ^{Return to the normal screen.}

Press SET UP.

NOTE:

When the selected language is not available on the disc, the

disc’s default menu language is played back.

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SETTINGS (cont.)

Language Code List

Afar

Inupiak

Kirundi

Rumanian

Russian

Kinyarwanda

Sanskrit

Sindhi

Sangho

Serbo-Croatian

Singhalese

Slovak

Abkhazian

Afrikaans

Ameharic

Arabic

Assamese

Aymara

Azerbaijani

Bashkir

Byelorussian

Bulgarian

Bihari

Bislama

Bengali, Bangla

Tibetan

Indonesian

Icelandic

Hebrew

Yiddish

Javanese

Georgian

Kazakh

Greenlandic

Cambodian

Kannada

Korean (KOR)

Kashmiri

Kurdish

Kirghiz

Latin

Lingala

Laothian

Lithuanian

Latvian, Lettish

Malagasy

Maori

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Malay (MAY)

Maltese

Burmese

Nauru

Nepali

Dutch

Norwegian

Occitan

(Afan) Oromo

Oriya

Slovenian

Samoan

Shona

Somali

Albanian

Serbian

Siswati

Sesotho

Sundanese

Swedish

Swahili

Tamil

Breton

Catalan

Corsican

Czech

Welsh

Danish

Bhutani

Greek

Esperanto

Estonian

Basque

Persian

Finnish

Telugu

Tajik

Thai

Tigrinya

Turkmen

Tagalog

Setswana

Tonga

Turkish

Tsonga

Tatar

Fiji

Faroese

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Twi

Ukrainian

Urdu

Uzbek

Hindi

Panjabi

Polish

Pashto, Pushto

Portuguese

Quechua

Rhaeto-Romance

Vietnamese

Volapuk

Wolof

Xhosa

Yoruba

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Zulu

Download from Www.Somanuals.com. All Manuals Search And Download.

D ^{Access the Clock Set screen.}

Clock Set

● Turn on the TV and select the video channel (or AV

mode).

Press rt to move the highlight bar (pointer) to “CLOCK

SET,” then press ENTER or e. The Clock Set screen

appears.

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Slide to the

right.

E ^{Set the date and time.}

Press rt to set the time, then press ENTER or e. The

“DATE” display begins blinking. Repeat the same

procedure to set the date and year.

● When you set the time/date, press and hold rt to change the

time by 30 minutes/15 days.

NOTE:

If the year digits are automatically cleared, it is possible that you

have input February 29th in a non-leap year. Input the correct

data.

F ^{Start the clock operation.}

Press SET UP.

To make corrections anytime during the process

Press ENTER or e repeatedly until the item you want to

change blinks, then press rt.

A ^{Turn on the unit.}

Press 1.

B ^{Select the VHS deck.}

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

Access the Main Menu screen, then Initial Set

screen.

Press SET UP. Press rt to place the pointer next to

“INITIAL SET,” then press ENTER or e.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK

A ^{Load a cassette.}

Basic Playback

● Turn on the TV and select the video channel (or AV

mode).

Make sure the window side is

up, the rear label side is

facing you and the arrow on

the front of the cassette is

● Slide the TV/VCR/DVD switch on the remote

control to the right.

pointed toward the unit.

● Do not apply too much

pressure when inserting.

● If the record safety tab has been removed, playback begins

automatically. Although the DVD deck is selected, the VHS

deck is selected automatically if the DVD deck is in stop

mode.

● Select the appropriate colour system with “PAL/MESECAM“

and “NTSC“ in Function Set. (੬ pg. 54)

● The unit’s power comes on automatically and the counter is

reset to 0:00:00.

B ^{Select the VHS deck.}

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the unit

Slide to the

right.

On the remote control

Press VCR so that the VCR indicator lights up.

C ^{Find the programme start point.}

If the tape is advanced past the start point, press 3. To

go forward, press 5.

D ^{Start playback.}

Press 4. “bESt” appears blinking on the front display

panel during automatic tracking. (੬ pg. 25)

E ^{Stop playback.}

Press 8. Then press x on the VHS deck to remove the

cassette.

Usable cassettes

● Compact VHS

camcorder

recordings can be

played on this unit.

Simply place the

recorded cassette

into a VHS Cassette

Adapter and it can be used just like any full-sized VHS

cassette.

● This video recorder is equipped with SQPB (S-VHS QUASI

PLAYBACK) that lets you watch tapes recorded in the

S-VHS format and the SP mode with regular VHS

resolution.

Clean the video heads using a dry cleaning

cassette — ECL-3F — when:

● Rough, poor picture appears while a tape is played back.

● The picture is unclear or no picture appears.

● “USE CLEANING CASSETTE” appears on the screen (only

with “O.S.D.” set to “ON”). (੬ pg. 54)

NOTE:

The heads get dirty in the following cases:

● in an environment prone to extreme temperature or

humidity

* SQPB does not deliver Super VHS resolution.

● This video recorder can record on regular VHS and Super

VHS cassettes. However, it will record regular VHS signals

only.

● in a dusty environment

● flaw, dirt or mold on video tapes

● continuous usage for a long time

* S-VHS recording is not possible with this recorder.

Download from Www.Somanuals.com. All Manuals Search And Download.

Skip Search

Playback Features

● Turn on the TV and select the video channel (or AV

mode).

During playback, press

unwanted sections.

1 to 6 times to skip over

Each press initiates a 30-second period of fast-motion

playback. Normal playback resumes automatically.

● Slide the TV/VCR/DVD switch on the remote

control to the right.

To resume normal playback during a Skip Search,

press 4.

ATTENTION

Index Search

In the search, still, slow-motion or frame-by-frame playback

mode,

Your unit automatically marks index codes at the beginning of

each recording. This function gives you quick access to any one

of 9 index codes in either direction.

● the picture will be distorted.

● the noise bars will appear.

● there may be a loss of colour.

● you cannot hear the sound.

NOTE:

Before starting, make sure the unit is in the Stop mode.

Activate Index Search.

Still Picture/Frame-By-Frame

Playback

Press 2 or 6. “2 1” or “6 1” is displayed on

the TV screen and search begins in the corresponding

direction.

● To access index codes 2

1 Pause during playback.

Current position

through 9, press 2 or

6 repeatedly until the

correct index number is

displayed.

Press 9.

● If there is vertical jitter, press PR +/– on the remote control to

correct the picture.

Example:

To locate the beginning of B

from the current position,

2 Activate frame-by-frame playback.

Press 9.

Index number

press 2 twice.

NOTE:

To locate the beginning of

Still picture playback stops automatically after 5 minutes to

protect the heads.

D from the current position, press 6 once.

● When the specified index code is located, playback begins

automatically.

Slow Motion

Next Function Memory

While playback is paused, press and hold 9 for 2

seconds, then release. Press 9 and release again to return

to still picture.

The Next Function Memory “tells” the unit what to do after

rewinding. Before continuing, make sure the unit is in the Stop

mode.

NOTE:

a- For Automatic Start Of Playback

Press 3, then press 4 within 2 seconds.

b- For Automatic Power Off

Press 3, then press 1 within 2 seconds.

c- For Automatic Timer Standby

Press 3, then press # within 2 seconds.

d- For Automatic Cassette Ejection After Tape Rewind

Press 3, then press x within 2 seconds.

During slow motion playback, some noise may appear on the TV

screen. Press PR + or – on the remote control to eliminate the

noises.

Variable Speed Search

During playback, press 5 for forward variable speed

search, or 3 for reverse variable speed search.

● The speed changes for each direction by pressing 3 or 5

repeatedly.

One Touch Replay

When pressing 5:+5x{+7x/

NTSC-EP +11x{+21x

Press

Pressing

during playback.

once moves the playback position back to about 7

When pressing 3:–1x]–5x{–7x/

NTSC-EP –1x]–11x{–21x

seconds before the current position. You can press

times each One Touch Replay.

up to 4

(Once

is pressed, reverse search starts in –1x normal

changes the

playback speed. After this process, each press of

search speed between –5x and –7x/NTSC-EP -11x and -21x.)

NOTE:

The search speed changes in the same way for SP, LP, and EP

modes.

To resume normal playback, press 4.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

Manual Tracking

Slide to the

right.

Your unit is equipped with automatic tracking

control. During playback, you can override this

and adjust the tracking manually by pressing the

TRACKING +/– buttons.

1 Override automatic tracking.

During playback, press TRACKING + and – at

the same time.

2 Adjust the tracking manually.

Press TRACKING +/–.

● Press TRACKING + and – at the same time again to return to

automatic tracking.

NOTE:

When a new tape is inserted, the unit enters the automatic

tracking mode automatically.

Soundtrack Selection

Your unit is capable of recording three soundtracks (HI-FI L,

HI-FI R and NORM) and will play back the one you select.

During Playback

Pressing A.MONITOR changes the soundtrack as follows:

Instant ReView

TRACK

Simply by pressing a single button, the unit power comes on,

rewinds, and begins playback of the last timer-recorded

programme. If you have several programmes recorded, you can

easily access any of them.

USE

On-Screen Display

HI FI

For Hi-Fi stereo tapes

L j h R

NOTE:

HI FI

L j

Before starting, make sure that the unit is off and that the Timer

mode is disengaged.

For main audio of Bilingual tapes

HI FI

For sub audio of Bilingual tapes

Activate Instant ReView.

h R

Press

. The unit power comes on and the unit

NORM

For audio-dubbed tapes

searches for the index code indicating the start of the last

timer-recorded programme. Once it’s found, playback

begins automatically.

HI FI

NORM

● To watch the first of the 3 programmes, press

three

NOTES:

times. The unit searches and begins playback automatically.

You can access a programme as far as 9 index codes away

from the current tape position.

● “HIFI L j h R” should normally be selected. In this mode,

Hi-Fi stereo tapes are played back in stereo, and the normal

audio track is played back automatically for tapes with only

normal audio.

● For instructions on recording stereo and bilingual

programmes, refer to page 25.

● “O.S.D.” must be set to “ON” or the on-screen displays will

not appear. (੬ pg. 54)

Repeat Playback

Your unit can automatically play back the whole tape 100 times

repeatedly.

1 Start playback.

Press 4.

2 Activate Repeat Playback.

Press 4 and hold for over 5 seconds, then release.

● The Play indicator ($) on the front display panel blinks slowly.

● After playing back a tape 100 times, the unit stops

automatically.

3 Stop Repeat Playback.

Press 8 at any time.

● Pressing 4, 3, 5 or 9 also stops Repeat Playback.

NOTE:

Repeat playback is not possible with a cassette recorded in EP

mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

D ^{Set the tape speed.}

display panel or TV screen. Press p again to change

the setting while the tape speed is displayed on the TV

screen.

● Each time you press p, the mode changes as follows.

SP{LP (or EP*)

Basic Recording

● Turn on the TV and select the video channel (or AV

mode).

Press p. The current setting appears on the front

● Slide the TV/VCR/DVD switch on the remote

control to the right.

* EP is for NTSC only.

E ^{Start recording.}

Press and hold 7 and press 4 on the remote control, or

press 7 on the unit.

B.E.S.T. works at the beginning of both the first SP and the

first LP recording after inserting the cassette. (੬ pg. 25)

Slide to the

right.

F ^{Pause/Resume recording.}

Press 9. Press 4 to resume recording.

● You can select channel during the Record Pause mode.

G ^{Stop recording.}

Press 8. Then press x on the VHS deck to remove the

cassette.

Recording Resume Function

If there is a power outage during recording, Instant Timer

Recording, or timer recording (੬ pg. 24, 29), the recording

will resume automatically when power is restored to the unit

unless the unit’s memory backup has expired.

Accidental erasure

prevention

To prevent accidental recording

on a recorded cassette, remove its

safety tab. To record on it later,

cover the hole with adhesive tape.

Record safety tab

A ^{Load a cassette.}

Insert a cassette with the record safety tab intact.

● The unit’s power comes on automatically and the counter is

reset to 0:00:00.

● Select the appropriate colour system with “PAL/MESECAM”

and “NTSC” (੬ pg. 54).

B ^{Select the VHS deck.}

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

C ^{Choose a programme.}

Press PR +/– or the number keys to select the channel

you wish to record.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

3 Set the recording duration.

If you want to record for more than 30 minutes, press 7

to extend the time. Each press extends recording time by

30 minutes.

Recording Features

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

NOTES:

● You can only perform ITR using the 7 button on the unit’s

front panel.

● When the end of the tape is reached during Instant Timer

Recording, the unit is turned off and “⅜” and “$” blink on

the front display panel.

● When the end of the tape is reached during timer recording,

the unit is turned off and “7”, “4” and “#” blink on the front

display panel.

Slide to the

right.

Elapsed Recording Time Indication

1 Set the counter display.

Press – –:– – until a counter reading appears on the front

display panel.

2 Reset the counter.

Press 0000 before starting recording or playback.

● The counter is reset to “0:00:00” and shows the exact elapsed

time as the tape runs. You can check the exact time of a

recording or playback.

Tape Remaining Time

Press – –:– – until the time remaining on the tape

appears.

Record One Programme While

Watching Another

● The front display panel shows the tape remaining time with “:”

displayed.

Once recording is in progress, all you need to do is to set

the channel controls on the TV for the station you wish to

view.

● The programme selected with the TV’s channel controls

appears on the TV screen, while the one selected with the

unit’s PR buttons is recorded on the tape.

● By pressing the – –:– – button, you can change the display to

show the channel position, clock time, counter reading, and

tape remaining time.

* The channel position is not displayed during playback.

NOTE:

You can also use the DVD deck in the following cases. Before

use, be sure to turn on the unit and select the DVD deck.

● During recording

NOTES:

● When you press – –:– –, the on-screen display appears on the

TV screen for 5 seconds.

● During timer recording

● During timer standby mode

● Depending on the type of tape being used, the tape remaining

time reading may not appear right away, or is not correct.

“– –:– –” may sometimes appear with “:” blinking, or the

display may blink on occasion.

Instant Timer Recording (ITR)

This easy method lets you record for

from 30 minutes to 6 hours (selectable in

30-min. increments), and shuts the unit

off after recording is finished.

1 Start recording.

Press 7 on the unit.

2 Engage the ITR mode.

Press 7 again. “⅜” blinks and “0:30” appears on the

front display panel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Receiving Stereo and Bilingual

Programmes

B.E.S.T. Picture System

Your unit is equipped with a Sound-Multiplex decoder (A2) and

a Digital stereo sound decoder (NICAM) making reception of

stereo and bilingual broadcasts possible.

The B.E.S.T. (Biconditional Equalised Signal Tracking)

system checks the condition of the tape in use during

playback and recording, and compensates to provide the

highest-possible playback and recording pictures. You

can set “B.E.S.T.” to “ON” or “OFF” to your preference.

(੬ pg. 54)

When the channel is changed, the type of broadcast being

received will be displayed on the TV screen for a few seconds.

Type of Broadcast Being

On-screen Display

Received

Playback

A2 Stereo

A2 Bilingual

Regular Monaural

NICAM Stereo

NICAM Bilingual

NICAM Monaural

BIL.

(none)

ST NICAM

BIL. NICAM

NICAM

The unit assesses the quality of the tape once you initiate

playback.

● The unit adjusts the playback picture quality based on the

quality of the tape in use.

● B.E.S.T. is active during automatic tracking. “bESt” appears

blinking on the front display panel.

● “bESt” only appears at the beginning of automatic tracking.

Even though it doesn’t appear after that, the B.E.S.T. function is

operative.

● To listen to a stereo programme, press A.MONITOR until

“HIFI L j h R” appears on the TV screen.

● To listen to a bilingual programme, press A.MONITOR until

“HIFI L j” or “HIFI h R” appears on the TV screen.

● To listen to the standard (Regular Monaural) audio while

receiving a NICAM broadcast, press A.MONITOR until

“NORM” appears on the TV screen.

Recording

The unit assesses the quality of the tape once you initiate

recording.

NOTE:

● The unit spends approximately 7 seconds assessing the

condition of the tape, then begins recording.

“O.S.D.” must be set to “ON,” or the on-screen displays will not

appear. (੬ pg. 54)

To Record Stereo and Bilingual Programmes (A2)

Stereo programmes are automatically recorded in stereo on the

Hi-Fi audio track (with the normal audio track recording mixed L

and R channel sound).

● Bilingual programmes are automatically recorded in bilingual

on the Hi-Fi audio track. The main soundtrack will be

recorded on the normal audio track.

ATTENTION

Since the B.E.S.T. system works before recording actually

starts, there is a delay of approximately 7 seconds after 7

and 4 on the remote control are pressed, or 7 on the unit is

pressed. To make sure you record the desired scene or

programme in its entirety, first perform the following steps:

A Press and hold 9 and press 7 to engage the Record Pause

mode.

To Record NICAM Stereo and Bilingual Programmes

The NICAM audio programme will be recorded on the Hi-Fi

audio track, and the standard audio programme will be recorded

on the normal audio track.

● The unit then automatically checks the condition of the

tape and, after approximately 7 seconds, re-enters Record

Pause mode.

B Press 4 to start recording.

If you want to bypass the B.E.S.T. system and begin recording

immediately, set “B.E.S.T.” to “OFF”. (੬ pg. 54)

NOTES:

● If the quality of stereo sound being received is poor, the

broadcast will be received in monaural with better quality.

● Before playing back a programme recorded in stereo, or a

bilingual programme, refer to “Soundtrack Selection” on

page 22.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

G-CODE^®/SHOWVIEW^TM

Guide Program Number Set

System Setup

A ^{Select the VHS deck.}

On the unit

The G-CODE timer programming system eliminates the need to

input channel, date, start and stop time data when setting the

timer record function.Simply key in the G-CODE number for the

TV programme you wish to record (found in most TV listings)

and the unit's timer is automatically programmed.

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

You have to set Guide Program numbers, which are assigned to

each station for purposes of ShowView timer programming, for

all the stations stored in your unit's memory to get proper results.

Before G-CODE setup you must have performed Auto Set Up.

(੬ pg. 14)

B ^{Access the Main Menu screen.}

Press SET UP.

IMPORTANT

C ^{Access the Initial Set screen.}

After setting the Guide Program Numbers, channel positions

may be incorrect if you stored or skipped channels. In this case,

re-perform Guide Program Number settings.

Press rt to move the highlight bar (pointer) to “INITIAL

SETUP,” then press ENTER or e.

INFORMATION

G-CODE and SHOWVIEW are different trademarks used to

represent the same easy recording feature, but only the term

G-CODE system will be used in the instructions. If you use the

SHOWVIEW system, follow the same instructions listed for

the G-CODE system.

D ^{Access the Guide Program Set screen.}

Press rt to move the highlight bar (pointer) to “G-CODE/

SHOWVIEW SETUP,” then press ENTER or e.

E ^{Enter the Guide Program number.}

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Press rt or number keys to

G-CODE/SHOWVIEW SETUP

enter the Guide Program

number for the desired

station as shown in the TV

listings. Then press ENTER or

GUIDE PROG

TV PROG

Slide to the

right.

[0-9] OR [

]

F ^{Enter the Receiving channel position number.}

G-CODE/SHOWVIEW SETUP

Then press rt or number

keys to input the number of

the unit’s channel position on

which the Guide Program

number’s broadcast is

GUIDE PROG

TV PROG

received by the unit. Then

press ENTER or e.

● If the satellite broadcast is

received on your unit's

[0-9] OR [

]

auxiliary channel “L-1,” select

“L-1” for the channel position.

● Repeat steps E and F as necessary.

G ^{Return to the normal screen.}

Press SET UP.

Guide Program Number

“Guide Program (GUIDE PROG) number” refers to the

assigned TV station numbers,according to broadcast

area, for G-CODE timer recording. The Guide Program

numbers can be found in most TV listings.

Download from Www.Somanuals.com. All Manuals Search And Download.

G-CODE^®/SHOWVIEW^TM

B ^{Access the G-CODE/SHOWVIEW screen.}

Press PROG.

Timer Programming

With the G-CODE^®/SHOWVIEW^TMsystem, timer programming is

greatly simplified because each TV programme has a

corresponding code number which your unit is able to

recognize.

G-CODE/SHOWVIEW SYSTEM

INFORMATION

G-CODE and SHOWVIEW are different trademarks used to

represent the same easy recording feature, but only the term

G-CODE system will be used in the instructions. If you use the

SHOWVIEW system, follow the same instructions listed for

the G-CODE system.

C ^{Enter the G-CODE number.}

Press the number keys to

enter the G-CODE number of

a programme you wish to

record.

Before performing the G-CODE^®/SHOWVIEW^TMTimer

Programming:

● If you make a mistake, press &

and input the correct number.

● Be sure to read “G-CODE^®/SHOWVIEW^TMSystem Setup” (pg.

26)

G-CODE/SHOWVIEW SYSTEM

● Make sure that the unit’s built-in clock is set properly.

● Insert a cassette with the safety tab in place. The unit will

come on automatically.

● Turn on the TV and select the video channel (or AV mode).

● Slide the TV/VCR/DVD switch on the remote control to the

right.

D ^{Access the G-CODE Program screen.}

Press ENTER, then the

G-CODE Program screen

appears (if you’re just starting

out, “P1” appears).

● Select the appropriate color system with “PAL/MESECAM”

and “NTSC.” (੬ pg. 54)

Slide to the

right.

IMPORTANT

Make sure the channel position number you wish to record is

displayed; if not, see “G-CODE^®/SHOWVIEW^TMSystem Setup” on

page 26 and set the Guide Program number correctly.

● If the number you entered is invalid, “ERROR” appears on the

TV screen. Press & and input a valid G-CODE number.

● If the “G-CODE/SHOWVIEW SETUP” screen appears, see

“ATTENTION” on page 28.

E ^{Set the tape speed.}

Press p (SP/LP or EP*).

* EP is for NTSC only.

A ^{Select the VHS deck.}

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

F ^{Return to the normal screen.}

ATTENTION

Guide Program Number Set

“G-CODE/SHOWVIEW SETUP”

appears afterperforming

step D if the Guide Program

number for the G-CODE

Press PROG or ENTER. “PROGRAM COMPLETED”

appears on the TV screen for about 5 seconds, then the

normal screen appears. If “PROGRAM OVERLAPPED”

appears on the TV screen, see page 28.

G-CODE/SHOWVIEW SETUP

GUIDE PROG

TV PROG

– –

● Repeat steps B – F for each additional programme.

number you entered has not

been set.

Press rt or the number keys

to input the channel position

number on which your unit

receives that station, then

press ENTER or e to set the Guide Program number. The

G-CODE Program screen appears.

[0-9] OR [

]

G ^{Engage the unit’s timer mode.}

[PROG] : EXIT

Press #. The unit turns off automatically and “#”

appears on the front display panel.

● To disengage the timer mode, press # again.

NOTES:

● To Change The Stop Time:

— press STOP +/– after pressing ENTER in step D. You can

compensate for anticipated programme schedule delays.

● To Timer-Record Weekly Or Daily Serials:

— after pressing ENTER in step D, press WEEKLY (number key

“9”) for weekly serials or DAILY (number key “8”) for daily

serials (Monday — Friday). Either “WEEKLY” or “DAILY”

appears on the TV screen. Pressing the button again makes the

corresponding indication disappear.

● You can programme this unit to timer-record as many as 8

programmes. If you try to programme the unit to record a

ninth, “PROGRAM FULL” appears on the TV screen and

“FULL” appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes. (੬ pg. 30)

Download from Www.Somanuals.com. All Manuals Search And Download.

D ^{Enter the programme start time.}

Express Timer

Programming

Press START +/– to enter the

time you want recording to

start.

If you do not know the G-CODE number for the programme you

wish to record, use the following procedure to set your unit to

timer-record the programme.

● Press and hold START +/– to

move in 30-minute

increments, or press and

release repeatedly to move 1

minute at a time.

Before performing Express Timer Programming:

● Make sure that the unit’s built-in clock is set properly.

● Insert a cassette with the safety tab in place. The unit will

come on automatically.

● Turn on the TV and select the video channel (or AV mode).

● Slide the TV/VCR/DVD switch on the remote control to the

right.

E ^{Enter the programme stop time.}

Press STOP +/– to enter the time you want recording to

stop.

● Select the appropriate colour system with “PAL/

MESECAM” and “NTSC” (੬ pg. 54).

● Press and hold STOP +/– to move in 30-minute increments, or

press and release repeatedly to move 1 minute at a time.

Slide to the

right.

F ^{Enter the programme date.}

Press DATE +/–.

● The current date appears on the TV screen. The date you enter

appears in its place.

G ^{Enter the channel position.}

Press PR +/–.

H ^{Set the tape speed.}

* EP is for NTSC only.

Example: To timer-record the programme from 21:00 to

22:00 on 25th December, on channel 1.

Press p (SP/LP or EP*).

A ^{Select the VHS deck.}

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

I ^{Return to the normal screen.}

On the unit

Press PROG or ENTER. “PROGRAM COMPLETED”

appears on the TV screen for about 5 seconds, then the

normal screen appears.

On the remote control

Press VCR so that the VCR indicator lights up.

● If “PROGRAM OVERLAPPED” appears on the screen, see

page 28.

● Repeat steps B – I for each additional programme.

B ^{Access the G-CODE/SHOWVIEW screen.}

J ^{Engage the unit’s timer mode.}

Press PROG.

Press #. The unit turns off automatically and “#”

appears on the front display panel.

C ^{Access the Programme screen.}

● To disengage the timer mode, press # again.

Press START +/–. (If you’re

just starting out, “P1”

appears.)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

To Timer-Record Weekly Or Daily Serials:

Check, cancel and change programmes

— anytime during steps D through H, press WEEKLY (number

key “9”) for weekly serials or DAILY (number key “8”) for daily

serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears

on the TV screen. Pressing the button again makes the

corresponding indication disappear.

A ^{Disengage the timer mode.}

Press #, then press 1.

NOTES:

● You can programme this unit to timer-record as many as 8

programmes. If you try to programme the unit to record a

ninth, “PROGRAM FULL” appears on the TV screen and

“FULL” appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes. (੬ “To cancel or change a programme”).

B ^{Access the Programme Check screen.}

Press ".

C ^{Access the Programme screen.}

Press " again to check

more information. Each time

you press ", the next

programme’s information

appears.

To cancel or change a programme

D ^{Cancel or change a programme.}

Press & to cancel a programme. To change programme

settings, press the appropriate button: START +/–,

STOP +/–, DATE +/–, PR +/–, DAILY (number key “8”),

WEEKLY (number key “9”) and/or p(SP/LP or EP*)

* EP is for NTSC only.

E ^{Return to the normal screen.}

Press " as many times as necessary. If there are still

some programmes remaining, go on to step F.

F ^{Return to the timer mode.}

Press #.

Download from Www.Somanuals.com. All Manuals Search And Download.

C ^{Cancel or change programme setting.}

Slide to the

right.

To cancel a programme, press & when the Programme

screen you do not want is shown. “PROGRAM

COMPLETED” appears on the TV screen for about 5

seconds, then the normal screen appears.

To change a programme, press the appropriate button:

START +/–, STOP +/–, DATE +/–, PR +/–, DAILY

(number key “8”), WEEKLY (number key “9”) and/or p

when the Programme screen on which you want to make

changes is shown, then press ENTER. “PROGRAM

COMPLETED” appears on the TV screen for about 5

seconds, then the normal screen appears.

NOTE:

If the overlap is not yet solved, or another overlap occurs with

the timer programme setting after making the last correction on a

programme, the conflicting programmes will be shown on the

Programme Check screen again. Repeat the above steps again

until the overlap is solved.

When programmes overlap each other

If “PROGRAM OVERLAPPED” appears, you have another

programme overlapping the programme you have just made.

The Programme Check screen appears and conflicting

programmes will start blinking.

Example: Programme 1 (you have just made) and

Programme 4 overlap each other.

A ^{Confirm the overlapping programmes.}

Overlapping programmes blink on the TV screen.

B ^{Select the programme to modify.}

Press rt, then press ENTER or e.

● You can only select one of the overlapping programmes.

NOTE:

If you do not mind this overlap, press PROG to finish the timer

programme setting. The programme with the lower programme

number will be recorded and the other one will not be recorded

correctly. If no changes are made for approximately 1 minute,

the unit will return to the normal screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON VHS DECK (cont.)

B ^{Set the tape speed.}

Automatic Satellite

Press p.

Programme Recording

Engage the Automatic Satellite Programme

This function allows you to automatically record a

satellite programme which is timer-programmed on your

external satellite receiver. Connect a satellite receiver to

the unit’s L-1 Input Connector (INPUT (L-1)) and

programme the timer on the satellite receiver. The unit

starts or stops recording by the signals input from the

satellite receiver. After recording, the unit’s power shuts

off automatically.

Recording mode.

Press and hold REC LINK for

about 2 seconds.

● The “N” and “#” indicators light

up and the unit turns off

automatically.

NOTES:

● Operation on the DVD deck is not possible when the

Automatic Satellite Program Recording mode is engaged, or

Timer Recording is in progress.

● To disengage the Automatic Satellite Programme Recording

mode, press REC LINK. The “N” indicator goes off.

● If the unit’s power is off, it is not possible to engage the

Automatic Satellite Programme Recording mode.

● In step C, if the “N” indicator does not light but instead blinks

quickly even though your satellite receiver’s power is off,

Automatic Satellite Programme Recording will not work

ATTENTION

● Be sure not to turn on the satellite receiver before the

programme is executed; otherwise, the unit will start

recording when the satellite receiver’s power is turned on.

● If you have connected another appliance other than a

satellite receiver to the L-1 Input Connector (INPUT

(L-1)), be sure not to engage the Automatic Satellite

Programme Recording mode; otherwise, the unit will start

recording when the connected appliance’s power is turned

on.

properly with that satellite receiver*.

* Some satellite receivers output signals even if the power is off.

Automatic Satellite Programme Recording is not possible with those

satellite receivers.

● Automatic Satellite Programme Recording and timer-

recording cannot be done at the same time.

● The “N” indicator blinks while Automatic Satellite Programme

Recording is in progress.

● For timer programming of the satellite receiver, refer to the

instruction manual of the satellite receiver.

● Automatic Satellite Programme Recording is not possible if

your satellite receiver does not have a timer.

● Pressing the unit’s 1 button while Automatic Satellite

Programme Recording is in progress turns off the unit’s power

and disengages the Automatic Satellite Programme Recording

mode.

Before performing the following steps:

● Make sure the satellite receiver is connected to the unit’s

L-1 Input Connector (INPUT (L-1)) connector.

● Programme the timer on the satellite receiver.

● Insert a cassette with the safety tab in place.

● Slide the TV/VCR/DVD switch on the remote control to the

right.

● If there are more than one satellite programmes you wish to

record with Automatic Satellite Programme Recording, it is not

possible to set different tape speeds for each programme.

● Depending on the type of satellite receiver, the unit may not

record a slight portion of the beginning of the programme or

may record slightly longer than the actual length of the

programme.

Slide to the

right.

● If you engage the Automatic Satellite Programme Recording

mode when the satellite receiver’s power is on, the unit will

not start Automatic Satellite Programme Recording even

though the “N” and “#” indicators blink. When the satellite

receiver shuts off once and is turned back on again, the unit

starts recording.

● You can also record a programme from your cable system in

the same way if the system has a timer.

● The B.E.S.T. system (੬ pg. 25) does not work while Automatic

Satellite Programme Recording is in progress.

A ^{Select the VHS deck.}

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK

A ^{Load the disc.}

Basic Playback

● For details, refer to “Placing a Disc” (੬ pg. 5).

B ^{Select the DVD deck.}

Press VCR/DVD repeatedly so that the DVD indicator

lights up.

On the unit

● Turn on the TV and select the VCR channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

On the remote control

Press DVD so that the DVD indicator lights up.

C ^{Start playback.}

Press 4.

Example: DVD VIDEO

Title number

Chapter number

Slide to the

right.

Playback time

● You can switch the display on the front display panel between

the title/chapter/track number and the playback time by

pressing – –:– –.

● It may take a few seconds to start playback.

● When inserting a DVD or Video CD disc, a menu display may

appear on the TV screen. To play back from the menu, refer to

“Locating a Desired Scene Using the Menu of the Video CD

with Playback Control (PBC) Function” (੬ pg. 34) or

“Locating a Desired Scene Using the DVD Menu” (੬ pg. 34).

D ^{Pause playback.}

Press 9.

● To resume normal playback, press 4.

E ^{Stop playback.}

Press 8.

● When “RESUME” (੬ pg. 58) is “ON,” the unit memorizes the

position on the disc where you have interrupted playback.

-To resume playback, press 4.

-To stop playback completely, press 8 again.

● Press x on the DVD deck to open the disc tray, then remove

the disc.

ATTENTION

● You can not use the DVD deck when the VCR deck is in

the Automatic Satellite Recording standby and recording

mode.

● You can use the DVD deck when the VCR deck is in the

timer standby mode.

● If the unit does not accept an operation,

TV screen. (Operations are occasionally unacceptable

even if is not displayed.)

appears on the

To play back a MP3/JPEG disc, see pages 42 – 44.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Locating a Desired Scene Using the

DVD Menu

Playback Features

● Turn on the TV and select the VCR channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

DVD VIDEO discs generally have their own menus which show

the disc contents. These menus contain various items such as

titles of movies, names of songs, or artist information, and

display them on the TV screen. You can locate a desired scene

using the DVD menu.

Slide to the

right.

1 Access the DVD menu.

Press TOP MENU or MENU.

2 Start playback.

Press rt w e to select a

desired item, then press

Example:

ENTER.

● It may be possible to select the

desired item using the number keys depending on the disc.

ZOOM

Locating a Desired Scene Using the

Menu of the Video CD with Playback

Control (PBC) Function

Some Video CD discs supports the PBC function. PBC is an

abbreviation of “PlayBack Control.” A Video CD disc recorded

with PBC has its own menus, such as a list of the songs of the

disc. You can locate a specific scene by using the menu.

1 Access the PBC menu.

In stop mode

Press 4.

● Depending on a disc, PBC

menu may automatically

appear on the TV screen by

simply loading a disc on the

unit. “Pbc” appears on the

front display panel.

Example:

During playback

Press RETURN.

2 Start playback.

Press the appropriate number keys.

● The unit starts playback of the selected item.

● When “NEXT” or “PREVIOUS” appears on the TV screen:

Pressing 6 advances to the next page.

Pressing 2 returns to the previous page.

● The method of the operation is different depending on the

disc.

To cancel PBC

Start playback by using the number keys instead of 4.

To reactivate PBC

● Press TOP MENU or MENU.

● Press 8 to stop playback, then press 4.

Download from Www.Somanuals.com. All Manuals Search And Download.

Locating the Start Point of the Item or Still Picture/Frame-By-Frame

Skip the Item

Playback

Press 2 or 6 during playback.

1 Pause during playback.

Press 9.

Example:

To locate the beginning of item B from the current position, press

2 twice.

To locate the beginning of item D from the current position,

press 6 once.

2 Activate frame-by-frame playback.

Press 9 to advance a still picture.

● To resume normal playback, press 4.

Current position

Slow Motion

The number you press the button

During playback, press 9, then press 5 for forward

slow motion playback, or 3 for reverse slow motion

playback.

● When the specified item is located, playback begins

automatically.

● Each press of 5 changes the playback speed as follows:

1/32]1/16]1/8]1/4]1/2

NOTE:

● Each press of 3 changes the playback speed as follows

(only for DVD VIDEO discs):

–1/32]–1/16]–1/8]–1/4]–1/2

When you press 2 or 6, the counter display may appear

instead of title number/chapter number depending on the discs.

● To resume normal playback, press 4.

Variable Speed Search

NOTES:

● Reverse slow motion playback is possible only with the DVD

VIDEO discs.

● This function may not works for some Video CD or SVCD.

During playback, press 5 for forward variable speed

search, or 3 for reverse variable speed search.

● The more times you press, the faster the playback picture

moves.

Zooming

● To resume normal playback, press 4.

During playback, press and hold 6 for forward search,

or press and hold 2 for reverse search.

● While you press and hold the button, the image is played back

at 5x speed.

Press ZOOM during playback or while paused.

● Each press of ZOOM changes the magnification in the

following steps:

ZOOM OFF ] ZOOM 1 ] ZOOM 2 ] ZOOM 3]

ZOOM 4 ] ZOOM 5 ] ZOOM 6 ] (Back to the beginning)

● While zoomed, the picture may look coarse or distorted.

● To resume normal playback, release 2 or 6.

NOTES:

● Actual speed may be different from that displayed on the TV

screen depending on the discs.

● Playback sound is not heard in any variable speed search

mode.

One Touch Replay

Zoomed-in area

Current magnification

Press rt w e to move the

zoomed-in scene.

Press

while playing back a DVD VIDEO disc.

The playback position moves back about 10 seconds before the

current position (only within the same title).

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

NOTES:

● Repeat Playback is not possible with a Video CD and SVCD

with PBC function.

Slide to the

right.

● Repeat Playback may not work properly depending on the

type of disc being used.

● You cannot select A-B Repeat Playback by pressing REPEAT.

A-B Repeat Playback

REPEAT

You can repeat the desired part.

1 Access the on-screen bar.

Press ON SCREEN twice. The on-screen bar appears on

the TV screen.

2 Select menu item.

Press w e to hightlight

, then press ENTER.

● The following pop-up window appears under the selected

item.

Repeat Playback

You can repeat playback as you like according to the type of

disc.

3 Select the repeat mode.

Press rt repeatedly to select “A-B.”

DVD VIDEO:

Audio CD:

during playback

during playback or in stop mode

4 Select the start point.

Video CD/SVCD: in stop mode or during playback with PBC

deactivated

Press ENTER at the beginning of the part you want to

repeat (point A).

1 Access the repeat mode.

● The following display appears in the on-screen bar.

Press REPEAT.

● Repeat mode is displayed on the TV.

2 Select the repeat mode.

Press REPEAT repeatedly to select the desired repeat

mode.

5 Select the end point

Press ENTER at the end of the part you want to repeat

(point B).

DVD VIDEO

CHAPTER]TITLE]OFF](Back to the beginning)

● A-B Repeat Playback starts. The selected part of the disc

(between point A and B) is played repeatedly.

CHAPTER:

TITLE:

The current chapter is played back

repeatedly.

To cancel A-B Repeat Playback

Repeat from step 1, select “OFF” in step 3, then press

ENTER.

The current title is played back

repeatedly.

To clear the on-screen bar

Press ON SCREEN.

Each title and chapter is played

back once.

OFF:

NOTE:

Video CD/SVCD/CD

TRACK]ALL]OFF](Back to the beginning)

The points A and B must be set in the same title or track.

The current track is played back

repeatedly.

TRACK:

ALL:

All tracks are played back

repeatedly.

Each track is played back once.

OFF:

● The pop-up window disappears if no operation is done for

about 5 seconds.

To cancel Repeat Playback

Press REPEAT repeatedly until “OFF” appears on the TV

screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Time Search

Subtitle Selection

You can play back a disc from the desired point by specifying the

elapsed time from the beginning of the current title (for DVD

VIDEO) or the disc (for Audio CD/Video CD) using the Time

Search.

You can select subtitle language.

● During playback

1 Access the menu.

Press SUBTITLE.

1 Access the on-screen bar.

Press ON SCREEN twice. The on-screen bar appears on

the TV screen.

● The following pop-up window appears on the TV screen.

Example (DVD):“ENGLISH” is selected out of 3 subtitle

languages recorded.

2 Select menu item.

Press w e to hightlight

, then press ENTER.

● The following pop-up window appears under the selected

item.

2 Select the subtitle language.

Press rt repeatedly to select the desired subtitle

language. To turn off the subtitle, press SUBTITLE

repeatedly until “OFF” is selected.

3 Select the time.

Press the number keys (0-9) to enter the time, then press

ENTER.

● Each time you press the button, the subtitle language changes.

● The pop-up window disappears if no operation is done for

about 5 seconds.

Example:

To play back from a point 2 (hours): 34 (minutes): 08 (seconds)

elapsed

NOTES:

TIME _ : _ _ : _ _

TIME _2 : _3 _ : _ _

TIME _2 : _3 _4 : _0 _

TIME _2 : _ _ : _ _

● For DVD VIDEO

Some subtitle languages are abbreviated in the pop-up

window. See “Language Code List” (੬ pg. 18).

● For SVCD

An SVCD can contain up to four subtitles. Pressing SUBTITLE

changes the subtitles regardless of whether the subtitles are

recorded or not.

Press 2

Press 3

TIME _2 : _3 _4 : _ _

Press 0

Press 4

Press 8

TTIIMMEE _2 ::_3 _4 ::_0 _8

If you have specified a wrong selection,

Press w repeatedly until the wrong number is erased,

then press number keys to enter the correct numbers.

● The unit starts playback from the specified time.

To clear the on-screen bar

Press ON SCREEN.

NOTE:

Some DVD VIDEO discs do not contain time information, and it

is no possible to use the Time Search function.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Audio Language and Sound Selection

Slide to the

right.

The audio selection setting allows you to change the audio

language of a movie, or to listen to karaoke with or without the

vocal.

● During playback

1 Access the menu.

Press A.MONITOR.

● The following pop-up window appears on the TV screen.

Example: “ENGLISH” is selected out of 3 audio languages

recorded during DVD VIDEO playback.

2 Select the audio setting.

Press rt or A.MONITOR repeatedly to select the

desired audio language.

● Each time you press the button, the audio selection changes.

● The pop-up window disappears if no operation is done for

about 5 seconds.

Angle Selection

DVD VIDEO (example)

1/3 ENGLISH]2/3 FRENCH]3/3 SPANISH](Back to the

beginning)

You can enjoy a variety of scene angles if the DVD VIDEO disc

contains “multi-angle” parts, where multiple cameras were used

to shoot the same scene from different angles.

● During playback

Video CD

ST]L]R](Back to the beginning)

1 Access the menu.

To listen to normal stereo playback.

To listen to L (left) audio channel only.

To listen to R (right) audio channel only.

ST:

Press ANGLE.

● The following pop-up window appears on the TV screen.

Example:The first view angle is selected out of 3 view angles

recorded.

SVCD

ST 1]ST 2]L 1]R 1]L 2]R 2](Back to the beginning)

To listen to normal stereo playback of ST 1 or

ST 2 channel.

ST 1/ST 2:

To listen to the L (left) 1 or 2 audio channel.

To listen to the R (right) 1 or 2 audio channel.

L 1/L 2:

R 1/R 2:

2 Select the view angle.

Press rt or ANGLE repeatedly to select the desired

view angle.

NOTE:

For DVD VIDEO discs, some audio languages are abbreviated in

the pop-up window. See “Language Code List” (੬ pg. 18).

● Each time you press the button, the angle of the scene

changes.

● The pop-up window disappears if no operation is done for

about 5 seconds.

Example:

1/3]2/3]3/3](Back to the beginning)

1/3

Download from Www.Somanuals.com. All Manuals Search And Download.

2 Select the VFP mode.

Sound Effect (3D PHONIC)

Press w e repeatedly.

● Each time you press w e, the VFP mode changes as follows:

NORMAL]CINEMA]USER 1]USER 2](Back to the

beginning)

Using the Sound Effect function (3D PHONIC), you can change

the sound field.

● This function works only for analog audio output.

NORMAL:

CINEMA:

Select this normally.

Suitable for movie.

1 Access the selection menu.

USER 1/

USER 2:

You can adjust parameters that affect picture

appearance and store settings. Go to step 3.

Press SOUND EFFECT during playback.

● The current setting appears on the TV screen.

To adjust picture appearance manually

2 Select the Sound Effect (3D PHONIC) mode.

3 Access USER menu.

Press SOUND EFFECT repeatedly to select the desired

mode.

Press w e repeatedly to select “USER 1” or “USER 2.”

● Each time you press SOUND EFFECT, the Sound Effect (3D

PHONIC) mode changes as follows:

OFF]ACTION]DRAMA]THEATER](Back to the

beginning)

4 Select the parameter.

Press rt repeatedly to select a parameter you want to

adjust, then press ENTER.

● Adjust gradually and confirm picture appearance results are as

preferred.

OFF:

ACTION:

No effect

Suitable for action movies and sports

programmes in which sounds dynamically

move.

GAMMA

Adjust this if the neutral color is bright or dark.

The brightness of dark and bright portions is

maintained.

(–3 to +3):

DRAMA:

Provides natural and warm sound. You can

enjoy movies in a relaxed mood.

You can enjoy sound effects like in a major

theater.

BRIGHTNESS Adjust this if the picture is bright or dark on

THEATER:

(–8 to +8):

the whole.

CONTRAST

Adjust this if the objects in far and near

positions look unnatural.

● The selection menu disappears if no operation is done for

about several seconds.

(–7 to +7):

SATURATION Adjust this if the picture is whitish or blackish.

NOTES:

(–7 to +7):

● The Sound Effect (3D PHONIC) function works correctly only

when playing back a DVD VIDEO disc recorded in the Dolby

Digital format. With other sources, you cannot get any effect if

you activate this function.

TINT

Adjust this if the appearance of flesh tone is

unnatural.

(–7 to +7):

SHARPNESS Adjust this if the picture is indistinct.

● When playing back a DVD VIDEO disc recorded with Dolby

Digital that does not contain the rear signal, you cannot get a

correct effect even if you activate the Sound Effect (3D

PHONIC) function.

(–8 to +8):

● VFP menu disappears and the following pop-up window

appears on the TV screen.

VFP function

— Adjusting the picture quality

GAMMA

5 Adjust the parameter.

The VFP (Video Fine Processor) function enables you to adjust

the picture character according to the type of programing,

picture tone or personal preference.

Press rt repeatedly to change the setting, then press

ENTER.

● The current VFP settings appear again.

Repeat steps 4 and 5 to adjust other parameters.

1 Access the VFP setting menu.

To return to the normal screen

Press DVD PICTURE.

NORMAL

Press DVD PICTURE during

GAMMA

playback.

● The current setting appears on

the TV screen.

BRIGHTNESS

CONTRAST

SATURATION

TINT

NOTE:

The VFP setting screen disappears if no operation is done for

more than about 10 seconds.

SHARPNESS

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Basic operation on the on-screen bar

During playback

Using the on-screen bar

A ^{Access the on-screen bar.}

You can check disc information while the disc is loaded and you

can use some functions using the on-screen bar. The on-screen

bar allows you the various playback operations.

Press ON SCREEN twice. The on-screen bar appears on

the TV screen.

● The currently selected item is highlighted.

Slide to the

right.

B ^{Select menu item.}

Press w e to hightlight the item you want to work wiht,

then press ENTER. The pop-up window appears under

the selected item.

ON SCREEN

After pressing ENTER

● When a pull-down menu appears, press rt to select the

setting you want, then press ENTER.

● When a number-entry box appears, use the number key to

enter the number you want, then press ENTER.

● When changing the indication of playback time, press ENTER

repeatedly to select the setting you want.

For details about each function, see page 41.

How to Access the On-Screen Bar

A ^{Access the status bar.}

Press ON SCREEN when a disc is loaded. The status bar

appears on the TV screen.

Example: During DVD VIDEO playback

Transfer

rate

Chapter

number

Playback

status

Title

number

Playback

time

B ^{Access the menu bar.}

Press ON SCREEN again. The menu bar appears under

the status bar.

To clear the on-screen bar

Press ON SCREEN.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Bar Functions for DVD VIDEO

Menu Bar Functions for SVCD/Video

CD/Audio CD

Time mode selection

During playback, selects the time mode shown in the status bar

and on the front display.

Time mode selection

● TOTAL: Current title elapsed time

Selects the time mode shown in the status bar and on the front

display.

● TIME: Current track elapsed time

● REM: Current track remaining time (while in stop mode,

current track total time)

● T.REM: Current title remaining time

● TIME: Current chapter elapsed time

● REM: Current chapter remaining time

Repeat mode (See also page 36)

● TOTAL: Disc elapsed time

● T.REM: Disc remaining time (while in stop mode, disc total

time)

Selects the repeat mode during playback.

● CHAPTER: Current chapter repeat

● TITLE: Current title repeat

● A-B: A-B repeat

● OFF: Repeat mode deactivated

Repeat mode (See also page 36)

Selects the repeat mode.

● TRACK: Current track repeat

● ALL: All track repeat

Time search (See also page 37)

● A-B: A-B repeat

● OFF: Repeat mode deactivated

Specifies a time from the beginning of the current title as the

point from which to begin playback.

CHAP.

Time search (See also page 37)

Chapter search

Specifies a time from the beginning of the disc as the point from

which to begin playback.

During playback, specifies a desired chapter to be played back

from.

Audio selection (See also page 38)

During Video CD/SVCD playback, selects the audio channel(s).

During playback, selects the audio language or sound track.

Subtitle selection (See also page 37)

Subtitle selection* (See also page 37)

During SVCD playback, selects the subtitle.

During playback, selects the subtitle language.

* It is impossible to select “OFF” when using the on-screen bar.

To select “OFF”, press ON SCREEN to clear the on-screen bar,

then press SUBTITLE repeatedly until “OFF” is selected.

Angle selection (See also page 38)

During playback, selects a desired scene angle in a multi-angle

part.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Control display

MP3/JPEG files Playback

The control display appears on the TV screen and playback starts

when an MP3 or a JPEG disc is loaded.

Outline

Example: When an MP3 disc is loaded

This unit can play back MP3 and JPEG files on a personally

recorded on CD-R/RW and commercially available CD disc.

● This unit may be unable to play back the disc due to the

characteristics or recording conditions.

Total group number on

disc

Current file

number

Total file number in

current group

FILE

Time – – : – –

Precautions

About files and folders (groups) on the disc

● This unit can recognize up to 99 groups and up to 150 files per

group.

If a disc includes more than the files above limit, the unit stops

detecting files when the number of detected files reaches the

limit and ignores the subsequent files. The unit also ignores

any non-MP3/JPEG file in the disc.

Group : 1 / 3

Blue

Red

Green

Track: 1 / 14 (Total 14)

Cloudy

Fair

Fog

Hail

Indian summer

Rain

Shower

Snow

Thunder

Typhoon

Wind

● Add the appropriate extension, such as “mp3” or “jpeg” to the

file name.

For making your own disc:

Winter sky

● Use “UDF format” as the disc format for CD-R/RW.

● Use “ISO 9660” as the disc format for CD-R/RW.

● The unit does not support “packet writing” for CD-R/RW.

● The unit supports discs recorded with up to five multiple

sessions.

Current group

number

Current file

Total file number on

disc

Current group

● Finalize the disc.

For MP3 files:

MP3i and MP3 Pro are not available.

* For MP3 only

Elapsed playing time of current track

Elapsed playing time is only shown during playback.

For JPEG files:

● This unit supports the JPEG files whose resolution is 32 to

8192 pixel in width and 32 to 7680 pixel in height.

● We recommend to record a file at 640 x 480 resolution. (If a

file has been recorded at a resolution of more than 640 x 480,

it will take a longer time to be displayed.)

NOTES:

● Because of the disc characteristics or recording condition,

some discs may not be played back or it takes time to start

playback.

● The unit does not support “packet writing” discs.

● If there are any files which are stored on a disc directly and do

not belong to any group, the unit recognized them as

belonging to an independent group.

● The unit plays back groups/files on a disc in the alphabetical

order. Therefore, playback order may be different from the

order recorded on a disc.

● Be sure to set “FILE TYPE” correctly when playing back a disc

which contains both MP3 and JPEG files. (੬ pg. 57)

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Playback

A ^{Load the disc.}

When you insert a disc with groups and files, the control display

that shows the contents of the disc automatically appears on the

TV screen. (੬ pg. 42)

● For details, refer to “Placing a Disc” (੬ pg. 5).

The control display appears on the TV screen. (੬ pg. 42)

You can specify and play back the desired group/file from the

control display using the following procedure.

B ^{Select the DVD deck.}

Press VCR/DVD repeatedly so that the DVD indicator

lights up.

● Turn on the TV and select the VCR channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

On the unit

On the remote control

Press DVD so that the DVD indicator lights up.

C ^{Select the group.}

Press rt to select the desired group, then press e.

D ^{Start playback.}

● You can skip a file across a group. Press 6 to skip to the first

file of the next group when the last file of the current group is

selected.

Press rt to select the desired file, then press ENTER or

Slide to the

right.

When playing back a JPEG disc, the slide-show playback

starts from the selected file.

● After selecting a file, press 4 to starts slide-show playback

from the selected file, or press ENTER to show the selected file.

● The playback interval time of slide-show depends on the file

size.

REPEAT

ZOOM

E ^{Pause playback.}

Press 9.

● To resume normal playback, press 4.

F ^{Stop playback.}

Press 8.

● Press x on the DVD deck to open the disc tray, then remove

the disc.

NOTES:

● 4, 8, 9, 2 and 6 buttons function the same as with

Audio CD discs, however, 5 and 3 buttons do not

function for MP3/JPEG files playback.

● Resume playback also does not function for MP3/JPEG files

playback.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS ON DVD DECK (cont.)

Repeat Playback

Slide to the

right.

You can repeat playback of the current group, file (only for MP3

files), or all groups.

● While the control display is on the TV screen:

1 Select the mode.

Press REPEAT to select the desired repeat mode.

● Each time you press REPEAT, the mode changes as follows:

For MP3 files playback

TRACK]GROUP]ALL]OFF (No indication)](Back to the

beginning)

The current file (track) is played

back repeatedly.

TRACK:

All files of the current group are

played back repeatedly.

GROUP:

All files are played back

repeatedly.

ALL:

Each file is played back once.

OFF (no indication):

For JPEG files playback

GROUP]ALL]OFF (No indication)](Back to the beginning)

All files of the current group are

played back repeatedly.

GROUP:

All files are played back

repeatedly.

ALL:

Each file is played back once.

OFF (No indication):

2 Start playback.

Group/File Selection

Press 4.

To start playback by specifying the group/file number

A Press the number keys (0-10, +10) to enter the group

number.

B Press the number keys (0-10, +10) to enter the file

number.

To cancel Repeat Playback

Press REPEAT repeatedly until the repeat mode display

disappears from the TV screen.

To return to the control display

Press 8.

Example:

To select 3:

To select 14:

To select 20:

Press 3.

Press +10, then 4.

Press +10, then 10.

Or press +10 twice, then 0.

Press +10, +10, then 4.

Zooming a still picture

Press ZOOM while playing back a JPEG file.

● When you want to zoom the picture during slide-show

playback, first press 9, then press ZOOM.

● Each press of ZOOM changes the magnification in the

following steps:

To select 24:

To select 110: Press +10 ten times, then 10.

To select 150: Press +10 fourteen times, then press 10 once.

For MP3 files playback

Playback starts from the file you have specified.

ZOOM OFF ] ZOOM 1 ] ZOOM 2 ] (Back to the

beginning)

● To resume normal playback, press ENTER.

For JPEG files playback

● The slide-show playback starts from the file you have

specified.

● To display only the selected file, then press ENTER. To start

slide-show playback from that file, press ENTER again.

NOTE:

You cannot select 150 even if you press +10 fifteen times, then

press 0 once.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING (VHS DECK)

A ^{Make connections.}

Edit From A Camcorder

You can use a camcorder as the source player and your

unit as the recording deck.

Connect the camcorder’s AUDIO OUT and VIDEO OUT

connectors to the unit’s front panel AUDIO and VIDEO

input connectors.

Slide the TV/VCR/DVD switch on the remote control

to the right.

● When using a monaural camcorder, connect its AUDIO OUT

connector to the AUDIO L input connector on your unit.

● When a Master Edit Control-equipped JVC camcorder is used,

the camcorder is capable of controlling the unit. Refer to the

camcorder’s instruction manual for operating procedure.

Recorder

B ^{Select the VHS deck.}

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

To PAUSE

connector

AUDIO input

On the remote control

Press VCR so that the VCR indicator lights up.

Audio cable (not provided)

Video cable (not provided)

Mini-plug cable

(not provided)

(JVC camcorder

only)

C ^{Set the unit’s input mode.}

Press AUX (number key “0”) and/or PR to select “F-1.”

VIDEO input

VIDEO OUT

AUDIO OUT

D ^{Set the edit mode.}

See “PICTURE CONTROL” on page 54.

E ^{Engage the Record Pause mode.}

EDIT

Player

Use 4, 3, or 5 to locate the point where you start

recording, then press and hold 9 and press 7 to engage

the Record Pause mode.

F ^{Start the camcorder.}

Engage the Play mode of the camcorder.

G ^{Start the unit.}

Press 4 to engage the Record mode of the unit.

NOTES:

● All necessary cables can be obtained from your dealer.

● When you select “EDIT” to dub tapes in step D, be sure to

select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”)

after you finish dubbing the tapes.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING (VHS DECK) (cont.)

Slide the TV/VCR/DVD switch on the remote control

Edit To Or From Another

Video Recorder

to the right.

A ^{Make connections.}

You can use your unit as the source player or as the

recording deck.

A When using your unit as the source player:

— connect its AUDIO/VIDEO OUTPUT connectors to

the recording deck.

A When using your unit as the source player:

Player

Your unit

TV receiver

B When using your unit as the recording deck:

— connect its L-1INPUT connector to the source

player.

AUDIO/VIDEO

OUTPUT

B ^{Select the VHS deck.}

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

Audio/video

cable

On the unit

Audio/video

cable

VCR channel

or AV mode

On the remote control

Press VCR so that the VCR indicator lights up.

Another recorder

Recorder

B When using your unit as the recording deck:

C ^{Set the input mode of recording deck.}

With this unit, press AUX (number key “0”) and/or PR to

select correct external input on the recording deck.

TV receiver

Recorder

Your unit

On this unit (when using this unit as the recording deck);

Select “L-1”— when connecting the other recorder to the

AV input connectors on the rear panel.

Select “F-1”— when connecting the other recorder to the

AV input connectors on the front panel.

F-1 VIDEO/AUDIO

Audio/video cable

● When using another recorder as the recording deck, refer to its

instruction manual.

Audio/video

cable

VCR channel

or AV mode

D ^{Set the edit mode.}

See “PICTURE CONTROL” on page 54.

Another recorder

Player

Recorder

Engage the Record Pause mode of the

recording deck.

TV receiver

Your unit

Locate the point where you start recording, then engage

the Record Pause mode.

F ^{Start the source player.}

INPUT (L-1)

Engage the Play mode of the source player.

Audio/video

cable

Audio/video

cable

G ^{Start the recording deck.}

VCR channel

or AV mode

Engage the Record mode of the recording deck.

Another recorder

NOTES:

● All necessary cables can be obtained from your dealer.

● When you select “EDIT” to dub tapes in step D, be sure to

select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”)

after you finish dubbing the tapes.

Player

● When you use this unit as the source player for editing, be sure

to set “O.S.D.” to “OFF” before starting. (੬ pg. 54)

Download from Www.Somanuals.com. All Manuals Search And Download.

C ^{Prepare the DVD deck for dubbing.}

B Start playback and search for the point where you

want to start dubbing by pressing 4, 5 or 3.

Dubbing

A Press DVD.

(from DVD to VHS)

You can dub selected scenes from the DVD disc to a cassette,

starting and stopping wherever you wish.

However, it is not possible to dub copy-protected discs.

In such case, “Err” appears on the front display panel.

D ^{Start dubbing.}

A little before the dubbing start point, press and hold 7,

then press 4 on the remote control.

● Turn on the TV and select the video channel (or AV

mode).

● “dub” lights on the front display panel.

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Slide to the

right.

E ^{End dubbing.}

Press 8.

● Be sure to press 8 while the VCR indicator lights up on the

unit.

● If you press 8 or x with the DVD deck selected, the dubbing

stopped, but the opening screen is also recorded.

● When you have finished dubbing, press DVD to select the

DVD deck and press 8 to stop playback.

NOTES:

● Set “ON SCREEN GUIDE” to “OFF” (੬ pg. 58) if you do not

want to record the on-screen display for DVD discs during

dubbing.

● There may be a discrepancy of several seconds between where

you intend editing to start, and where it actually starts.

● The superimposed indication during the operation or dubbing

is not recorded.

● Set “PICTURE CONTROL” to “EDIT”. (੬ pg. 54)

● When you select a setting as “MONITOR TYPE” other than

“MULTI” options (੬ pg. 15), it may not be possible to dub a

DVD disc in a cassette correctly.

A ^{Load a cassette and place a disc.}

For the VHS deck

Insert a cassette with the record safety tab intact.

For the DVD deck

For details, refer to “Placing a Disc” (੬ pg. 5).

B ^{Prepare the VHS deck for dubbing.}

A Press VCR.

B Press p to select recording speed.

C Search for the point where you want to start dubbing

by pressing 4, 5 or 3 then press 8.

Download from Www.Somanuals.com. All Manuals Search And Download.

EDITING (DVD DECK)

You can dub selected audio from the DVD or Audio CD disc to

an MD etc.

However, it is not possible to dub copy-protected discs.

Digital Audio Dubbing

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Example: Dubbing to an MD

A ^{Make connections.}

Connect the optical cable between the unit and the

digital audio device.

Recorder

B ^{Place a disc and load an MD.}

For the DVD deck

A Press x on the DVD deck to open the disc tray.

B Place the disc in the disc tray.

C Press x on the DVD deck to close the disc tray.

Digital audio device

(MD deck etc.)

For the digital audio device

Insert an MD.

Optical cable

(not provided)

C ^{Prepare the DVD deck for dubbing.}

A Press DVD and select the audio to be dubbed.

B Search for the point where you want to start dubbing

by pressing 4, 5 or 3 then press 8.

C Press 3 a little, then press 4 to start playback.

D Press 9 to pause playback a little before the start

point.

DIGITAL AUDIO OUT

Player

D ^{Prepare the audio device for dubbing.}

Select the input mode.

Note for connection:

Remove the connector cover from

the unit and remove the protection

cap from the cable.

E ^{Start dubbing.}

A Press 4 (or press 7 on the unit) to start playback on

the DVD deck.

B Start recording on the audio device.

F ^{End dubbing.}

Stop recording on the audio device. Then press 8 to stop

playback on the DVD deck.

NOTES:

● There may be a discrepancy of several seconds between where

you intend editing to start, and where it actually starts.

● You can also dub audio from a Video CD or SVCD. Set

“DIGITAL AUDIO OUTPUT” to “PCM ONLY”. (੬ pg. 57)

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL

On the remote control

Keep pressing VCR down during steps A – B.

Remote Control Functions

Remote A/B/C/D Code Switching

A ^{Change the remote control code.}

Press the number key “1” for A, “2” for B, “3” for C or

“4” for D.

The remote control is capable of controlling four JVC video units

independently. Each of the units can respond to one of four

codes (A, B, C or D). The remote control is preset to send A code

signals because your unit is initially set to respond to A code

signals. You can easily modify your unit to respond to B, C or D

code signals.

B ^{Set the remote control code.}

Press ENTER to set the code.

On the unit

Before performing the following steps:

Slide the TV/VCR/DVD switch on the remote control to the

right.

C ^{Turn off the unit.}

Press 1.

Slide to the

right.

D ^{Display the code.}

Press 4 on the unit for over 5 seconds while the unit is

turned off. The code currently set appears on the front

display panel.

● If the code displayed on the front display panel is different

from the code set on the remote control, go to step E.

E ^{Change the unit’s code.}

Press 8 on the remote control. The code currently set on

the remote control will be applied to the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL (cont.)

Operating a JVC TV

Slide the TV/VCR/DVD switch on the

remote control to the left.

Your remote control can operate the basic functions of your JVC

TV set.

B ^{Operate the TV.}

TV %+/– (Volume), TV PR +/–,

keys.

Slide to the

left.

Press the corresponding button: TV 1, TV/VCR,

(TV Muting), number

● For some JVC TVs, you must press ENTER after having pressed

the number keys.

Control Your JVC TV Using Additional Buttons

Use the number keys, and the p button or & button to

select the TV’s channel.

● The p button corresponds to the 1-digit/2-digit entry

switching button (often labelled – /– –) of your TV’s remote

control.

● With some JVC TVs, the & button corresponds to the 10 +

button of your TV’s remote control.

NOTE:

The way these buttons are used is determined by your TV.

Use these buttons as instructed for your TV’s remote control.

IMPORTANT

Although the provided remote control unit is compatible with

JVC televisions, it may not work with your JVC TV, or in some

instances, may have limited function capability.

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM CONNECTIONS

Connecting To A Satellite Receiver

Connect the satellite receiver to the AUDIO/VIDEO IN

NOTES:

connectors, then connect the AUDIO/VIDEO OUT or

● You cannot use Automatic Satellite Programme Recording

function if you connect the satellite receiver with S-video

cable. (੬ pg. 12)

S VIDEO OUT connectors to the TV’s connectors.

● To record a programme via the satellite receiver, select L-1 or

S-1 mode by pressing AUX (number key “0”) and/or PR so that

“L-1” or “S-1” appears on the front display panel.

● For details, refer to the instruction manual of the satellite

receiver.

Outdoor unit

Audio/video input connectors

Aerial

Back of TV

TV aerial cable

Satellite cable

ANT. IN

Satellite receiver

Aerial

connector

S-video input

connector

RF OUT

AUDIO/VIDEO

output connectors

INPUT

(L-1)

S VIDEO

VIDEO

AUDIO

VIDEO

AUDIO

DVD

AUDIO

OUTPUT

COMPONENT

VIDEO OUT

OUTPUT

DVD/VCR

DVD

Back of unit

Mains outlet

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM CONNECTIONS (cont.)

NOTES:

Connecting To A Dolby

Digital Decoder or An

Amplifier With A Built-in

DTS (DVD deck)

● For Dolby Digital sound, set “DIGITAL AUDIO OUTPUT” to

“DOLBY DIGITAL/PCM”. (੬ pg. 57)

● For DTS sound, set “DIGITAL AUDIO OUTPUT” to “STREAM/

PCM”. (੬ pg. 57)

CAUTIONS:

● This unit has a dynamic range of more than 80 dB with regards

to its Hi-Fi audio capability. It is recommended that you check

the maximum level if you are going to listen to the Hi-Fi audio

signals through a stereo amplifier. A sudden surge in the input

level to the speakers may damage them.

These instructions enable you to connect your unit to a

Dolby Digital Decoder or an amplifier with built-in DTS.

● Some speakers and televisions are specially shielded to

prevent television interference. If both are of the non-shielded

type, do not place the speakers adjacent to the TV set as this

can adversely affect the video playback picture.

Make connections.

Connect the optical cable between the unit and the

Dolby Digital Decoder or amplifier with a built-in DTS.

Dolby Digital Decoder or

amplifier with built-in DTS

To DIGITAL AUDIO

input

Optical cable

(not provided)

DIGITAL

AUDIO OUT

Note for connection:

Remove the connector cover from

the unit and remove the protection

cap from the cable.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS

A ^{Turn on the unit.}

Function Set (VHS deck)

Press 1.

You can change various mode settings on the Function

Set screen by following the procedure described below.

● For each mode setting, see pages 54 to 55.

B ^{Select the VHS deck.}

On the unit

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

Slide to the

right.

C ^{Access the Main Menu screen.}

Press SET UP.

D ^{Access the Mode Set screen.}

Press rt to move the

highlight bar (pointer) to

FUNCTION SET

“FUNCTION SET,” then press

TUNER SET

INITIAL SET

ENTER or e.

E ^{Select the mode.}

Press rt to move the highlight bar (pointer) to the item

you want to change.

FUNCTION SET

VIDEO STABILIZER

AUTO POWER OFF

B.E.S.T.

AUTO

OFF

PICTURE CONTROL

PAL/MESECAM

NTSC

AUTO

NTSC 3.58

O.S.D.

AUTO SP LP TIMER

OFF

F ^{Select the mode setting.}

Press ENTER or e.

G ^{Return to the normal screen.}

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

* The default setting is bold in the table below.

Ⅵ PAL/MESECAM — AUTO / PAL / MESECAM

8 B.E.S.T. — ON / OFF

Select the appropriate colour system for recording or playback.

AUTO: Usually set to this mode. The appropriate colour system

(PAL or MESECAM) will be selected depending on the

playback or recording signals.

You can set the B.E.S.T. (Biconditional Equalised Signal Tracking)

system to “ON” or “OFF.” (੬ pg. 25)

If the “AUTO” mode does not work properly, select either of

the following manual modes.

PAL: To record PAL signals, or playback a PAL tape.

MESECAM: To record SECAM signals, or playback a SECAM or

MESECAM tape.

NOTES:

● When watching a tape recorded with “B.E.S.T.” set to “ON,” it

is recommended that you leave B.E.S.T. on during playback as

well.

● When watching a rental tape or one recorded on another

video recorder, or when using this unit as the player for

editing, set B.E.S.T. to your preference.

● The B.E.S.T. system works for both SP and LP modes only after

a tape has been inserted and the Record mode is first initiated.

It does not work during recording.

● The B.E.S.T. system does not work while Automatic Satellite

Programme Recording is in progress. (੬ pg. 32)

● In the case of timer recordings, the B.E.S.T. system works

before recording is initiated.

● Once the cassette is ejected, the B.E.S.T. data is cancelled. The

next time the cassette is used for recording, B.E.S.T. is re-

performed.

NOTES:

● SECAM signals will always be recorded as MESECAM. Select

“AUTO” or “MESECAM” when recording SECAM signals.

● When playing back a SECAM tape, select “AUTO” or

“MESECAM.” The playback picture will always be

monochrome.

Ⅵ NTSC — NTSC3.58 / NTSC4.43 / NTSC]PAL

To record NTSC signals or playback a NTSC tape, it will be

necessary to select the appropriate mode.

NTSC3.58: To record NTSC signals or playback a NTSC tape.

NTSC4.43: To record NTSC4.43 signals or playback a NTSC4.43

tape.

● Pressing the unit’s 7 button while “bESt” is displayed does not

start Instant Timer Recording. (੬ pg. 24)

NTSC]PAL: To playback a NTSC tape on PAL TV.

NOTES:

8 PICTURE CONTROL— AUTO (NORM) / EDIT / SOFT

This feature helps you to adjust the playback picture quality

according to your preference. Normally select “AUTO.”

AUTO (NORM): Normally select this. Picture quality is adjusted

automatically. When “B.E.S.T.” is “OFF,” “NORM” will appear

instead of “AUTO.”

● The “NTSC]PAL” mode does not work during recording. In

this mode, NTSC signals will be recorded as NTSC3.58.

● The Menu screen is distorted during playing back a NTSC tape

on PAL TV. Stop playback and access the Menu screen again.

● In the “NTSC4.43” mode, with some TVs, on-screen displays

(Program screen, etc.) may roll up or down and there may be a

loss of colour. When this happens, select the “NTSC3.58”

mode.

EDIT: Minimizes picture degradation during editing (recording

and playback).

SOFT: Reduces image coarseness when viewing overplayed

8 O.S.D. — ON / OFF

tapes containing a lot of noise.

When this function is set to “ON,” various operational indicators

appear on the TV screen. Messages appear in the selected

language. (੬ pg. 14, 16)

NOTES:

● When you select “EDIT” or “SOFT,” the selected mode will not

change until you select another mode.

NOTES:

● When you select “EDIT” to dub tapes, be sure to select

“AUTO” after you finish dubbing the tapes.

● When “B.E.S.T.” is “OFF,” “PICTURE CONTROL” switches

automatically from “AUTO” to “NORM.”

● When you use this unit as the source player for editing, be sure

to set “O.S.D.” to “OFF” before starting.

● During playback, the operation mode indicators may be

disturbed depending on the type of tape being used.

Download from Www.Somanuals.com. All Manuals Search And Download.

8 AUTO SP]LP TIMER — ON / OFF

When this function is set to “ON,” the unit automatically

switches to LP mode to allow complete recording if there is not

enough tape to record the entire programme while timer-

recording in SP mode.

For Example:

Recording a programme of 210 minutes in length onto a 180-

minute tape

Approximately 150 minutes

SP mode

Approximately 60 minutes

LP mode

Total 210 minutes

Make sure you set this function to “ON,” before the timer-

recording starts.

NOTES:

● If you have programmed the unit to timer-record 2 or more

programmes, the second programme and those thereafter may

not fit on the tape if you set “AUTO SP]LP TIMER” to “ON.”

In this case, make sure the mode is not engaged, then set the

tape speed manually during timer programming.

● In order to ensure that the recording fits on the tape, this

feature may leave a slight non-recorded section at the end of

the tape.

● There may be some noise and sound disturbance at the point

on the tape where the unit switches from SP to LP mode.

● The Auto SP]LP Timer feature is not available during ITR

(Instant Timer Recording), and the feature will not work

properly with any tapes longer than E-180, or with some tapes

of shorter lengths.

8 VIDEO STABILIZER — ON / OFF

When this function is set to “ON,” you can automatically correct

vertical vibration in the picture when playing back unstable

recordings made on another recorder.

NOTES:

● When you finish viewing a tape, be sure to set this function to

“OFF.”

● Regardless of the setting, this function has no effect during

recording and during special effects playback.

● The on-screen display may jitter vertically when this function

is set to “ON.”

● To watch recordings with close-caption, set this function to

“OFF.”

8 AUTO POWER OFF — 3H / OFF

When this function is set to “3H,” the unit is turned off

automatically if no operation is done within 3 hours. “AUTO

POWER OFF IN 3 MIN” appears on the screen 3 minutes before

the unit is turned off.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

● The procedure shows how to set “RESUME” to “ON”

on the DVD Set Up menu screen as an example.

Mode Set (DVD deck)

You can change various mode settings on the Mode Set

screen by following the procedure described below.

● For each mode setting, see corresponding pages.

A ^{Turn on the unit.}

Press 1.

MENU LANGUAGE (੬ pg. 17)

AUDIO LANGUAGE (੬ pg. 17)

B ^{Select the DVD deck.}

LANGUAGE

SUBTITLE (੬ pg. 17)

ON SCREEN LANGUAGE (੬ pg. 17)

On the unit

Press VCR/DVD repeatedly so that the DVD indicator

MONITOR TYPE (੬ pg. 15)

lights up.

PICTURE SOURCE (੬ pg. 57)

PICTURE

SCREEN SAVER (੬ pg. 57)

FILE TYPE (੬ pg. 57)

On the remote control

Press DVD so that the DVD indicator lights up.

DIGITAL AUDIO OUTPUT (੬ pg. 57)

ANALOG DOWNMIX (੬ pg. 57)

C ^{Access the DVD Set Up menu screen.}

AUDIO

D. RANGE CONTROL (੬ pg. 57)

OUTPUT LEVEL (੬ pg. 57)

A Press SET UP.

OTHERS

RESUME

B Press w e to select

ON SCREEN GUIDE

PARENTAL LOCK

RESUME (੬ pg. 58)

ON SCREEN GUIDE (੬ pg. 58)

PARENTAL LOCK (੬ pg. 58)

“

OTHERS.”

OTHERS

● Each time you press the

button, the setup menus

change as follows;

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

LANGUAGE] PICTURE] AUDIO ] OTHERS

](Back to the beginning)

D ^{Select the mode.}

Press rt to move H to “RESUME,” then press ENTER.

Slide to the

right.

E ^{Select the mode setting.}

Press rt to select “ON,” then press ENTER.

F ^{Return to the normal screen.}

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

* The default setting is bold in the table below.

Audio Settings

Picture Settings

8 DIGITAL AUDIO OUTPUT —

PCM ONLY / DOLBY DIGITAL/PCM / STREAM/PCM

8 MONITOR TYPE —

Set to the appropriate mode according to the type of the device

connected to DIGITAL AUDIO OUT connector on the rear of

unit.

16:9 NORMAL/16:9 MULTI NORMAL /

16:9 AUTO/16:9 MULTI AUTO /

Set this item correctly according to the logo on the

4:3 LB/4:3 MULTI LB /

4:3 PS/4:3 MULTI PS

device.

It is not necessary to set this mode when you connect no device

to the DIGITAL AUDIO OUT connector.

You can select the monitor type depending on the TV used when

you play back DVD VIDEO discs recorded for wide-screen TVs.

For more details, refer to “Monitor Set (DVD deck)” (੬ pg. 15).

PCM ONLY: Select this when connecting to a device

bearing neither Dolby Digital nor DTS logo, or a digital

recorder.

8 PICTURE SOURCE —

VIDEO (NORMAL) / VIDEO (ACTIVE) / FILM / AUTO

You can obtain optimal picture quality by selecting whether the

content on the disc is processed by field (video source) or by

frame (film source).

DOLBY DIGITAL/PCM: Select this when connecting an

amplifier or a decoder bearing Dolby Digital (without

DTS) logo.

STREAM/PCM: Select this when connecting an amplifier

or a decoder bearing both Dolby Digital and DTS logos.

Normally set to “AUTO.”

VIDEO (NORMAL): Suitable for playing back a video source disc

with relatively a few movements.

8 ANALOG DOWNMIX — DOLBY SURROUND / STEREO

Set to the appropriate mode according to your audio system

when you play back a DVD VIDEO disc recorded with surround

multichannel audio. This setting affects only the analogue audio

output signal from the AUDIO OUT connectors when playing

back a DVD VIDEO disc recorded with surround multichannel

audio.

DOLBY SURROUND: Select this when you enjoy multichannel

surround audio by connecting the unit’s analogue AUDIO

OUTPUT connectors (DVD) to a surround decoder or an

internal amplifier.

VIDEO (ACTIVE): Suitable for playing back a video source disc

with relatively a lot of movements.

FILM: Suitable for playing back a film or progressive source disc.

AUTO: Used to play back a disc containing both video and film

source materials. This unit recognizes the picture type (film or

video source) of the current disc according to the disc

information.

● If the playback picture is unclear or noisy, or the oblique lines

of the picture are rough, try to change to other modes.

STEREO: Select this when you enjoy conventional 2-channel

stereo audio by connecting the unit’s analogue AUDIO

OUTPUT connectors (DVD) to a stereo amplifier/receiver or

TV, or when you dub audio of a DVD VIDEO disc recorded

with surround audio to your MD, cassette, etc.

8 SCREEN SAVER — ON / OFF

The TV screen may be burned out if a static picture is displayed

for a long time. When this function is set to “ON,” the unit

automatically activates the screen saver function if a static

picture, such as an on-screen display or menu is displayed for

over 5 minutes.

8 D. RANGE CONTROL —

WIDE RANGE / NORMAL / TV MODE

NOTE:

This function is not available for Audio CDs and MP3 discs.

The dynamic range (the difference between the loudest sound

and the quietest one) can be compressed during playback of a

programme encoded in Dolby Digital format.

8 FILE TYPE — AUDIO / STILL PICTURE

You can select files to play back, when both MP3 files and JPEG

files are recorded on a disc.

This function takes effect when a DVD VIDEO disc recorded in

Dolby Digital format is played back at low or middle volume.

WIDE RANGE: Select this to inactivate this function when you

AUDIO: Select this to play back MP3 files.

STILL PICTURE: Select this to play back JPEG files.

enjoy wide dynamic range programme.

NORMAL: Normally select this setting to activate this function.

NOTE:

TV MODE: Select this when you hear the sound through the TV's

You cannot access the DVD Set Up screen and “X” appears on

the TV screen if a disc is already placed.

speaker(s).

8 OUTPUT LEVEL — STANDARD / LOW

You can lower the output level of analog audio to accommodate

the unit to the connected A/V equipment.

STANDARD: Normally select this.

LOW: The output level of analog audio is lowered.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

Output

Playback discs

STREAM/PCM

DTS bitstream

DOLBY DIGITAL/PCM

PCM ONLY

DVD VIDEO with

48 kHz, 16/20/24 bit linear

PCM

48 kHz, 16 bit linear PCM

DVD VIDEO with DTS

44.1 kHz, 16 bit stereo linear PCM

DVD VIDEO with Dolby

Digital

48 kHz, 16 bit stereo linear

PCM

Dolby Digital bitstream

44.1 kHz, 16 bit stereo linear PCM

Linear PCM

Audio CD/Video CD

Audio CD with DTS

MP3 disc

DTS bitstream

Parental Lock

NOTES:

● The unit is not equipped with the DTS decoding function.

● When you play back a DVD VIDEO or Audio CD disc with

DTS, use a DTS decoder to get correct signals from your

speakers. Never use the unit’s analog output connectors,

which output incorrect signals that may damage your

speakers.

This function restricts playback of DVD VIDEO discs which

contains violent (and other) scenes according to the level set by

the user. Scenes which are limited by this function are not played

or replaced with other scenes.

8 COUNTRY CODE

● If you connect the analog outputs and digital outputs

simultaneously, be sure to select the source of the amplifier

correctly, or set the level control of the amplifier connected to

the analog outputs to minimum.

Select the code of your country/area. (੬ pg. 59)

8 SET LEVEL

Select the level of restriction. (“1” is the strictest.)

Others Settings

8 PASSWORD

Enter your password by pressing the number keys (0-9).

8 RESUME — ON / OFF

8 EXIT

When this function is set to “ON,” you can use the resume

function. (੬ pg. 33)

Select this, then press ENTER to go back to the OTHERS menu

screen.

ON: The unit resumes playback from the position where

playback has been stopped

NOTES:

OFF: You cannot use the resume function.

● Some DVD VIDEO discs cannot be played by this function. If

you try to play such a disc, the PARENTAL LOCK menu screen

appears on the TV screen and asks whether you want to

release the lock or not.

NOTE:

This function is not available for Audio CDs and MP3 discs.

To release the lock and play, select “TEMPORARY RELEASE,”

press ENTER, then enter your password. Otherwise, eject the

disc.

● To change the setting of the limitation, you need to enter your

password.

8 ON SCREEN GUIDE — ON / OFF

When this function is set to “ON,” the unit can display “on-

screen guide” icons or characters which show the conditions of

the unit or disc.

● If you forget your pass word, enter “8888.”

8 PARENTAL LOCK

Select this, then press ENTER to show the PARENTAL LOCK

menu screen for limiting playback by children.

Download from Www.Somanuals.com. All Manuals Search And Download.

Country/Area Code List for Parental Lock

AW Aruba

Andorra

Spain

Ethiopia

Finland

Fiji

Falkland Islands (Malvinas)

Micronesia (Federated States of)

Faroe Islands

France

France, Metropolitan

Gabon

United Kingdom

Grenada

Georgia

Saint Lucia

Liechtenstein

Sri Lanka

Liberia

Lesotho

Lithuania

Luxembourg

Latvia

Saudi Arabia

United Arab Emirates

Afghanistan

Antigua and Barbuda

Anguilla

Albania

Armenia

Netherlands Antilles

Angola

Antarctica

Argentina

American Samoa

Austria

Solomon Islands

Seychelles

Sudan

Sweden

Singapore

Saint Helena

Slovenia

Svalbard and Jan Mayen

Slovakia

Libyan Arab Jamahiriya

MA Morocco

MC Monaco

MD Moldova, Republic of

MG Madagascar

MH Marshall Islands

Sierra Leone

SM San Marino

Senegal

SO Somalia

Australia

French Guiana

Ghana

Gibraltar

Mali

Suriname

Sao Tome and Principe

El Salvador

Syrian Arab Republic

Swaziland

Turks and Caicos Islands

Azerbaijan

Bosnia and Herzegovina

Barbados

Bangladesh

Belgium

Burkina Faso

Bulgaria

Bahrain

Burundi

Benin

Bermuda

Brunei Darussalam

Bolivia

Brazil

Bahamas

Bhutan

Bouvet Island

Botswana

Belarus

Belize

Canada

Cocos (Keeling) Islands

Central African Republic

Congo

Switzerland

Côte d’Ivoire

Cook Islands

Chile

Cameroon

China

Colombia

Costa Rica

Cuba

Cape Verde

Christmas Island

Cyprus

Czech Republic

Germany

Djibouti

Denmark

MM Myanmar

MN Mongolia

MO Macau

Greenland

GM Gambia

Guinea

Northern Mariana Islands

Guadeloupe

Equatorial Guinea

Greece

South Georgia and the South

Sandwich Islands

Guatemala

MQ Martinique

MR Mauritania

MU Mauritius

MV Maldives

MW Malawi

MX Mexico

MY Malaysia

MZ Mozambique

NG Nigeria

NO Norway

NU Niue

TD Chad

TG Togo

TH Thailand

Montserrat

Malta

French Southern Territories

Tajikistan

Tokelau

Guam

GW Guinea-Bissau

HM Heard Island and McDonald

Islands

TM Turkmenistan

TN Tunisia

TO Tonga

TW Taiwan

UA Ukraine

UG Uganda

UM United States Minor Outlying

Islands

UY Uruguay

UZ Uzbekistan

Guyana

Hong Kong

Namibia

New Caledonia

Niger

East Timor

Turkey

Trinidad and Tobago

Tuvalu

Honduras

Croatia

Haiti

Hungary

Indonesia

Ireland

Israel

India

British Indian Ocean Territory

Iraq

Iran (Islamic Republic of)

Iceland

Italy

Jamaica

Jordan

Japan

Kenya

Norfolk Island

Nicaragua

Netherlands

Tanzania, United Republic of

Nepal

Nauru

United States

New Zealand

OM Oman

Panama

Peru

French Polynesia

Papua New Guinea

Philippines

Pakistan

Poland

Saint Pierre and Miquelon

Pitcairn

Puerto Rico

Portugal

Vatican City State (Holy See)

VC Saint Vincent and the Grenadines

Venezuela

VG Virgin Islands (British)

VI Virgin Islands (U.S.)

PW Palau

VN Viet Nam

VU Vanuatu

WF Wallis and Futuna Islands

WS Samoa

Kyrgyzstan

Cambodia

Kiribati

Comoros

Yemen

Mayotte

Saint Kitts and Nevis

Korea, Democratic People’s

Republic of

Korea, Republic of

Kuwait

Cayman Islands

Kazakhstan

Lao People’s Democratic

Republic

YU Yugoslavia

South Africa

ZM Zambia

Zaire

Paraguay

Qatar

Réunion

Romania

DM Dominica

Dominican Republic

Algeria

Ecuador

Estonia

Egypt

Western Sahara

Eritrea

ZW Zimbabwe

Russian Federation

RW Rwanda

Lebanon

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

D ^{Access the Auto Channel Set screen.}

Tuner Set

A Press rt to move the

TUNER SET

highlight bar (pointer) to

FUNCTION SET

IMPORTANT

“TUNER SET,” then press

TUNER SET

Perform the following steps only if —

— Auto Channel Set has not been set correctly by Auto Set

Up .(੬ pg. 14)

— you have moved to a different area or if a new station

starts broadcasting in your area.

ENTER or e.

INITIAL SET

B Press rt to move the

highlight bar (pointer) to

“AUTO CH SET,” then

press ENTER or e.

Your unit needs to memorize all necessary stations in channel

positions in order to record TV programmes. Auto Channel Set

automatically assigns all receivable stations in your area to call

them up by using the PR buttons without going through any

vacant channels.

E ^{Select the TV system.}

C Press rt to move the

highlight bar (pointer) to the

appropriate TV system (refer

to the table below), then

press ENTER or e.

TV SYSTEM SELECT

B/G

D/K

● Turn on the TV and select the video channel (or AV

mode).

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Slide to the

right.

Major Countries/Areas

TV System

Australia, New Zealand, Kuwait,

U.A.E., Indonesia, Singapore,

Thailand, Malaysia, Iran, Saudi Arabia,

Egypt, Morocco, Lebanon, Iraq

B/G

China, Mongolia, Russia

Hong Kong

D/K

● Auto Channel Set will start.

CH FRQ SYS CH FRQ SYS

01 150 BG

02 165 BG

03 195 BG

04 205 BG

05 213 BG

06 221 BG

07 229 BG

08 237 BG

09 355 BG

10 365 BG

11 374 BG

12 384 BG

AUTO CH SET

PLEASE WAIT

START

FINISH

[

]

[

] : DELETE

: EDIT

❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ – – – – – – –

[SET UP] : EXIT

F ^{Return to the normal screen.}

● Using the Confirmation screen, you can delete channels, swap

channel positions and fine-tune channels already stored. Refer

to page 62 for the procedures.

Auto Channel Set

Press SET UP.

A ^{Turn on the unit.}

Press 1.

IMPORTANT

● If no sound accompanies the picture or the audio

sounds unnatural on some channels that have been

stored by Auto Channel Set, the TV system setting

for those channels maybe incorrect. Select the

appropriate TV system for those channels. Refer to

“TV System Selection – When you see the picture

but the audio can’t be heard or sounds unnatural“

(੬ pg. 63).

B ^{Select the VCR deck.}

On the unit

Press VCR/DVD repeatedly so that the VCR indicator

lights up.

On the remote control

Press VCR so that the VCR indicator lights up.

● Since your recorder memorises all detected stations

even if the reception condition is poor, some of

those stored stations may produce a noisy picture.

To delete those stations, refer to “Delete A Channel“

(੬ pg. 62).

C ^{Access the Main Menu screen.}

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual Channel Set

F ^{Set the station.}

Store channels that were not stored during Auto Set Up

The screen to the right

appears when the station is

detected.

(੬ pg. 14) or Auto Channel Set (੬ pg. 60).

STORE

CONTINUE

A ^{Access the Main Menu screen.}

If you do not want to store

the detected station...

Press rt to move the

highlight bar (pointer) to

”CONTINUE” then press

ENTER or e. Channel

search will resume.

Press SET UP.

B ^{Access the Tuner Set screen.}

Press rt to move the highlight bar (pointer) to “TUNER

SET,” then press ENTER or e.

If you want to store the detected station...

Press rt to move the highlight bar (pointer) to ”STORE,”

then press ENTER or e. The Channel List appears again.

● The blueback screen and the TV picture currently being

broadcast appear alternately for 8 seconds each.

● If you want to store another channel, repeat steps D – F.

● When channel search completes for that band, the Band

Select screen appears again. To set channels for other bands,

select another band and start Manual Channel Set again (੬

steps E and F).

C ^{Access the channel list.}

Press rt to move the highlight bar (pointer) to ”CH

EDIT,” then press ENTER or e.

D ^{Select the channel position.}

Press rt to move the highlight bar (pointer) to an open

channel position, then press ENTER or e.

G ^{Return to the normal screen.}

Press SET UP.

E ^{Select the band.}

● To change positions, see “Swap Channel Position” (੬ pg. 62).

Press rt to move the highlight bar (pointer) to the

desired band, then press ENTER to initiate Manual

Channel Set.

BAND SELECT

MANUAL CH SET

PLEASE WAIT

VHF H

UHF

VHF L 300MHZ

[SET UP] : EXIT

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

Swap Channel Position

Slide to the

right.

Perform steps A to C of “Manual Channel Set” on page 61 to

access the Channel List screen before continuing.

A ^{Select the position (e.g. 03).}

Press rt until the section of CH “03” begins blinking,

then press ENTER or e.

● Only “03” will blink.

B ^{Select the position (e.g. 09).}

Press number keys to input “0” and “9.”

● The two selected channels will be swapped.

● To cancel the channel swapping, press w.

CH FRQ SYS CH FRQ SYS

01 150 BG

02 165 BG

03 195 BG

04 205 BG

05 213 BG

06 221 BG

07 229 BG

08 237 BG

09 355 BG

10 365 BG

11 374 BG

12 384 BG

01 150 BG

02 165 BG

03 355 BG

04 205 BG

05 213 BG

06 221 BG

07 229 BG

08 237 BG

09 195 BG

10 365 BG

11 374 BG

12 384 BG

[0 – 9] : INPUT CH

[ENTER] : FINE TUNING

[SET UP] : EXIT

[

] : CANCEL

[ENTER] : OK

[SET UP] : EXIT

● Repeat steps A and C as necessary.

C ^{Store the new position.}

Press ENTER or e.

Delete A Channel

D ^{Return to the normal screen.}

Press SET UP.

Perform steps A and C of “Manual Channel Set” on page 61

to access the channel list screen before continuing.

A ^{Select the channel.}

Press rt until the channel you want to delete begins

blinking.

B ^{Delete a channel.}

Press &.

● To re-store it, simply press w.

● The item directly beneath the cancelled one moves up one

line.

● Repeat steps A and B as necessary.

C ^{Return to the normal screen.}

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

Fine Tuning Channels Already Stored

TV System Selection — When you see

the picture but the audio can’t be

heard or sounds unnatural

Perform steps A to C of “Manual Channel Set” on page 61 to

access the channel list screen before continuing.

Perform steps A and C of “Manual Channel Set” on page 61

to access the Channel List screen before continuing.

A ^{Select the channel to fine-tune.}

Press rt until the channel you want to tune begins

blinking, then press ENTER twice.

A ^{Select the channel.}

you want to change its TV

system begins blinking,

then press ENTER three

times.

● The “SYS” display for that

channel starts blinking.

● The ”FRQ” number for the channel starts blinking.

Press rt until the channel

CH FRQ SYS CH FRQ SYS

01 150 BG

02 165 BG

03 195 BG

04 205 BG

05 213 BG

06 221 BG

07 229 BG

08 237 BG

09 355 BG

10 365 BG

11 374 BG

12 384 BG

B ^{Perform tuning.}

Press rt until the picture is its clearest. Then press

ENTER or e.

● Repeat steps A and B as necessary.

[

] : SELECT SYSTEM

[ENTER] : OK

C ^{Return to the normal screen.}

[SET UP] : EXIT

Press SET UP.

B ^{Select the TV system.}

Press rt to select the appropriate TV system

(B/G]D/K]I). Then press ENTER or e.

● Repeat steps A and B as necessary.

C ^{Return to the normal screen.}

Press SET UP.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

You can disable the unit’s operation.

Child Lock

A ^{Set the Child Lock.}

● Turn on the TV and select the video channel (or AV

mode).

Press and hold 1 on the remote control for more than

10 seconds while the unit is turned on. The unit turns off,

and “CL“ appears on the front display panel.

● Slide the TV/VCR/DVD switch on the remote

control to the right.

Slide to the

right.

● To release the child lock, press and hold 1 on the remote

control until the unit turns on.

NOTES:

● When the child lock function is in use, keep the remote

control out of the children’s reach.

● Timer recording programmes will be performed even if the

child lock function is activated.

Download from Www.Somanuals.com. All Manuals Search And Download.

Information on Multi-System Compatibility

(VHS deck)

Off-Air Recording

The built-in multi-system tuner is capable of receiving PAL B/G, I and D/K, and SECAM B/G and D/K broadcasts.

HR-XV38SAG/HR-XV38SAS

TV System

Recorded tape

Multi-system tuner

(B/G, I, D/K)

NOTE:

This model does not operate in BRAZIL (PAL-M) or ARGENTINA (PAL-N).

Playback

This unit can play all 3 types of recorded tape.

Recorded tape

HR-XV38SAG/HR-XV38SAS

Playback circuit

Multi-system

receiver

Built-in

RF converter

K, I, G, H

RF OUT

Multi-system

monitor

Manual switching

VIDEO OUT

AUDIO OUT

NOTES:

When viewing NTSC tapes on a PAL TV set:

● The picture may shrink vertically with black bars appearing at the top and bottom of the screen. This is not a malfunction on the part

of the nor the TV.

● The picture may roll up or down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if

the TV does not have a V-HOLD control.)

● During search, still, or frame-by-frame playback, the picture will be distorted, and there maybe a loss of colour.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUBSIDIARY SETTINGS (cont.)

ATTENTION

When this unit is connected to a multi-system TV, the audio signal may not be heard or maybe noisy if the colour system select

switch of the TV is adjusted to the AUTO position. In such a case, set the TV’s colour system select switch to the appropriate

position which corresponds to the TV system you have selected at the TV System Select screen.

Tape-To-Tape Editing

There are 3 different types of recorded tape, depending on the signal recorded.

Recorded tape

Playback equipment

HR-XV38SAG/HR-XV38SAS

Dubbed tape

Recording circuit

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Before requesting service for a problem, use this chart

and see if you can repair the trouble yourself. Small

problems are often easily corrected, and this can save

you the trouble of sending your unit off for repair.

Noise appears during normal playback.

● The automatic tracking mode is engaged.

]Try manual tracking. (੬ pg. 22)

The playback picture is blurred or interrupted while TV

broadcasts are clear or “USE CLEANING CASSETTE”

message appears on the screen.

Power

No power is supplied to the unit.

● The video heads may be dirty.

]Use a dry cleaning cassette ECL-3F, or consult your JVC

dealer.

● The mains power cord is disconnected.

]Connect the mains power cord.

The remote control won’t function.

Breaks are noticeable in Hi-Fi soundtrack.

● The batteries are discharged.

]Replace the dead batteries with new ones.

● The automatic tracking mode is engaged.

]Try manual tracking. (੬ pg. 22)

Tape Transport (VHS deck)

During recording, the tape does not run. “ ” lights up on

the front display panel.

Playback (DVD deck)

The button does not work.

● The operation is prohibited on the placed disc.

● The unit is in the Record Pause mode.

]Press 4 to resume recording.

The DVD deck cannot be operated.

The tape will not rewind or fast-forward.

● The DVD deck is not selected.

On the unit

● The tape is already fully rewound or fast-forwarded.

]Check the cassette.

]Press VCR/DVD repeatedly so that the DVD indicator lights

up.

On the remote control

]Press DVD so that the DVD indicator lights up.

Playback (VHS deck)

The VHS deck can not be operated.

“

” appears on the TV screen.

● The VHS deck is not selected.

On the unit

● The operation is prohibited on the placed disc.

]Press VCR/DVD repeatedly so that the VCR indicator lights

“REGION CODE ERROR!” appears on the TV screen.

up.

● The disc’s region number does not match that of the unit.

]Use the discs whose region number matches with your unit.

(੬ pg. 4)

On the remote control

]Press VCR so that the VCR indicator lights up.

The playback picture does not appear while the tape is

running.

The disc cannot be played back.

● The disc’s region number does not match that of the unit.

]Use the discs whose region number matches with your unit.

(੬ pg. 4)

● This type of disc cannot be played back.

]See “Unplayable Discs” (੬ pg. 4).

● The disc is not placed properly.

]Remove the disc, then place the disc properly in the disc tray.

(੬ pg. 5, “Placing a Disc”)

● The Parental Lock is engaged, and the placed disc is rated

higher than the set level.

● If you are using the RF connection,

— the TV receiver’s channel selector is not set to the video

channel.

— the unit’s video channel has not been correctly set.

]If you are using the RF connection,

— set the TV receiver to the video channel.

— perform “Video Channel Set” (੬ pg. 13).

● If you are using the AV connection, the TV receiver is not set

to the AV mode.

]If you are using the AV connection, set the TV to its AV mode.

]Release the Parental Lock temporarily, or change the set level.

(੬ pg. 58)

Noise appears during visual search.

● This is normal.

The language is not played back as you set.

● The disc does not contain the language you set.

The playback picture does not appear while the DVD disc is

played.

● Scan mode is set to PROGRESSIVE.

]Change the Scan mode to the Interlace. (੬ pg. 11)

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING (cont.)

Recording (VHS deck)

Changing audio/subtitle language is not possible.

● The disc does not contain audio/subtitles in multiple

languages.

]With some discs, the language should be set on the top menu.

(੬ pg. 34)

Recording cannot be started.

● There is no cassette loaded, or the cassette loaded has had its

record safety tab removed.

]Insert a cassette, or using adhesive tape, cover the hole where

the tab was removed.

The subtitles do not appear on the TV screen.

● The disc does not contain subtitles.

TV broadcasts cannot be recorded.

● The subtitle display is set to off.

● “L-1” or “F-1” has been selected as the input mode.

]Set to the desired channel.

]Set the subtitles display to on. (੬ pg. 37)

● A-B Repeat Playback is in progress. (੬ pg. 44)

]The subtitles recorded around point A-B may not appear.

Tape-to-tape editing is not possible.

● The source (another video recorder, camcorder) has not been

properly connected.

]Confirm that the source is properly connected.

● All necessary power switches have not been turned on.

]Confirm that all units’ power switches are turned on.

● The input mode is not correct.

Angle cannot be changed.

● The scene is not recorded from multiple angles.

MP3/JPEG Files Playback (DVD deck)

A disc cannot be played.

]Set the input mode to “L-1” or “F-1.”

● No MP3 files or JPEG files are recorded to the disc.

]Replace to the disc with MP3 files or JPEG files are recorded.

● Files do not have the correct file extension in their file names.

]Add correct file extension to their file names.

● Files are not recorded in a format compliant with ISO 9660

Level 1 or 2.

Camcorder recording is not possible.

● The camcorder has not been properly connected.

]Confirm that the camcorder is properly connected.

● The input mode is not correct.

]Set the input mode to “L-1” or “F-1.”

]Replace the disc. (Record files using a compliant application.)

● The types of files other than MP3 or JPEG are recorded to the

disc.

]The disc which contains the types of files other than MP3 or

JPEG may not be played because of its disc characteristics or

recording conditions.

“

” and “ ” on the front display panel won’t stop blinking.

● The end of the tape was reached during recording.

]The programme may not have been recorded in its entirety.

Next time make sure you have enough time on the tape to

record the entire programme.

When playing back a disc which contains both MP3 files

and JPEG files, either MP3 files or JPEG files are played.

The channel cannot be changed.

● Recording is in progress.

]Press 9 to pause the recording, change channels, then press

4 to resume recording.

● When playing back a disc which contains both MP3 files and

JPEG files, the selected files in the “FILE TYPE” setting are

played back .

]Set “FILE TYPE” to either “AUDIO” (for MP3 files) or “STILL

PICTURE” (for JPEG files) which you want to play back

beforehand. (੬ pg. 57)

The control display appears on the TV screen, but no

operation can be performed.

● No MP3 files or JPEG files are recorded to the disc, or the disc

is an unplayable disc (such as CD-ROM).

]Replace the disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER RECORDING (VHS deck)