DVD PLAYER
VIDEO CASETTE
RECORDER
USER'S GUIDE
For model:
HR-XVC1UJ
Hi-Fi
POWER
TV
VCR
DVD
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
POWER
INPUT
TV VOL
TIMER
TV/VCR
0
PLAY
STOP
C
SKIP
SKIP
/INDEX
/INDEX
SET
ENTER/
SELECT
SET
SET UP
MENU
CANCEL
VCR/DVD/TV
For Customer Use:
Enter below the Model No. and Serial No. which are located on the rear of cabinet.
Retain this information for future reference.
Model No.
Serial No.
LPT0708-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
MOISTURE CONDENSATION
When the equipment is installed in a cabinet or a shelf, make
sure that it has sufficient space on all sides to allow for
ventilation (10 cm or more on both sides, on top and at the
rear).
Moisture in the air will condense on the DVD/VCR when you
move it from a cold place to a warm place, or under
extremely humid conditions—just as water droplets form on
the surface of a glass filled with cold liquid. Moisture
condensation on the head drum will cause damage to the
tape. In conditions where condensation may occur, keep the
DVD/VCR’s power turned on for a few hours to let the
moisture dry.
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the
disposal of these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the DVD/VCR, Remote or video cassette.
1. DO NOT place the DVD/VCR ...
... in an environment prone to extreme temperatures or humidity.
... in direct sunlight.
How to use the Remote
Before use, insert two AAA size batteries into the Remote
with the polarity ( and ) matched correctly as indicated
on the battery compartment or on the lid.
Point the Remote toward the remote sensor on the target
component.
The maximum operating distance of the remote control is
about 5 m.
... in a dusty environment.
... in an environment where strong magnetic fields are generated.
... on a surface that is unstable or subject to vibration.
2. DO NOT block the DVD/VCR’s ventilation openings or
holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the DVD/VCR or Remote.
4. DO NOT place anything which might spill on top of the
DVD/VCR or Remote.
NOTE:
If the Remote does not work properly, remove its batteries,
wait for a few seconds, replace the batteries and then try
again.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
Video heads cleaning
The heads get dirty in the following cases:
in an environment prone to extreme temperature or humidity.
in a dusty environment
flaw, dirt or mold on video tapes
continuous usage for a long time
Use a dry cleaning cassette — TCL-2 — when:
Rough, poor picture appears while a tape is played back.
The picture is unclear or no picture appears.
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with
water. Also DO NOT place any containers filled with water
or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups, etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
8. AVOID violent shocks to the DVD/VCR during transport.
Important Warning
CAUTION:
A DVD/VCR IS A CLASS 1 LASER PRODUCT. HOWEVER THIS DVD/VCR USES A VISIBLE LASER
BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO
OPERATE THE PLAYER CORRECTLY AS INSTRUCTED.
THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE DVD/VCR.
CLASS 1
LASER PRODUCT
WHEN THIS DVD/VCR IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO
THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS
DVD/VCR.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION:
THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND
RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT A JVC
AUTHORIZED SERVICE CENTER.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE
LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO
BEAM.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
*This product incorporates copyright protection technology that is protected by
method claims of certain U.S.patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision Corporation or other
rights owners and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation or other rights owners.Reverse
engineering or disassembly is prohibited.
*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories. Confidential unpublished works. ©
1992-1997 Dolby Laboratories, Inc. All rights reserved.
*“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
*Certain audio features of this product manufactured under license from Desper
Products,Inc.Spatializer and the circle - in - square device are trademarks owned
by Desper Products,Inc.
*Unauthorized recording of copyrighted television programs, films, video cassettes
and other materials may infringe the rights of copyright owners and be contrary
to copyright laws.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
DVD/CD Player/Video Cassette Recorder
• DVD/CD player withVideo Cassette Recorder - Unique space saving design combines a DVD/CD player and a Hi-Fi Video
cassette recorder.The DVD disc has much more capacity, but is the same size as the audio CD disc.Picture quality is higher
than Super VHS. Audio quality is higher than audio CD. The DVD PLAYER can play back video CDs and audio CDs.
• High Quality Picture - More than 500 lines(VCR mode: 230 lines) of Horizontal Resolution. It exceeds Super VHS (400
lines) or Laser Disc (430 lines) in resolution.
VCR Section
• Stereo/SAP Reception - This VCR is designed to receive stereo and separate audio program (SAP) broadcasts where
available.
• SQPB - Tapes recorded in the S-VHS system can be played back simply on this VCR.
• 4 Video Heads - Provides optimal picture quality for special effects playback.
• 19µm HEAD - For superior picture quality even in EP mode, 19micron width technology helps to avoid crosstalk and
boost EP picture quality to near SP levels. With precision technology, ghosts and color beats are virtually eliminated.
• Hi-Fi Stereo Sound - With a frequency response of 20 to 20,000 Hz and a dynamic range of better than 90dB, this
VCR provides a level of excellence that rivals compact discs.
• Instant Timer Recording (ITR) - Simply by pressing the REC and PLAY buttons, the VCR can be programmed for up
to 5 hours of recording with an immediate start.
• Skip Search - When the SKIP SEARCH button is pressed during playback, the VCR will automatically search forward
in 30 seconds increments to a maximum of 3 minutes with each press of the SKIP SEARCH button, and then return to
normal playback.
DVD Section
• Compatible with a wide range of DVD audio outputs
Digital Audio Jack (Optical or Coaxial):
• When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the effect of
being in a movie theater or a concert hall.
• Surround standard different from Dolby Digital. This format is already in use in many theaters. By connecting this unit
to a DTS decoder or an AV amplifier with a built-in DTS decoder, the DTS audio of DVD discs recorded in this format
can be enjoyed. However, audio will not be output from the analog audio output jacks.
• The MPEG audio of DVD discs recorded in this format can be enjoyed.
• The Linear PCM sound of a 48 kHz/16 bit through 96 kHz/20 bit exceeds audio CD sound.
• Surround audio - This DVD equipped with a “SPATIALIZER 3-D STEREO”. It can produce the effect of being in a cinema
or a concert hall.
• Multi-Language - Since this DVD matches with 124 language-subtitles/-soundtracks, you can enjoy selecting a favorite
one. (You can not select the language that is not recorded on the disc.)
• Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc, you
can change the angles during playback. (If a Multi-Angle is not recorded on the disc, you can not change the angle.)
• Repeat Playback - You can repeat chapter, track, title, sides or material between two selected points.
• Program/Random Playback (CD) - You can play back tracks in programmed or random-selected sequences.
• Zoom - You can zoom in on the selected subject on the screen during playback.
• Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor/television on a suitable disc.
• Parental Control - You can limit the playback of scenes or sounds of adult DVD discs which have a parental level rating.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Before using your unit
Disc Playback operation
Important safeguards .......................................3
Power Source...................................................5
Features ...........................................................6
Contents...........................................................7
Parts and functions ..........................................8
Display .............................................................9
Remote control ...............................................10
Basic connections ..........................................12
CATV (CABLE TV) connections.....................14
Playback Connection .....................................16
Disc ................................................................ 35
Setting setup language .................................. 36
Playback procedure ....................................... 37
Special playback ............................................ 38
Zooming ......................................................... 39
Locating Desired Scene ................................. 39
Repeat playback ............................................ 40
Program playback (CD).................................. 41
Random playback (CD) .................................. 41
MP3 Playback ................................................ 42
Marking Desired Scenes ................................ 43
Changing soundtrack language ..................... 44
Subtitles ......................................................... 44
Changing angles ............................................ 45
Title selection ................................................. 45
DVD menu...................................................... 45
Setting up the VCR section
Setting the Video Channel ............................. 18
Setting the language ...................................... 18
Tuner Setting.................................................. 19
To ADD/DELETE channels............................. 20
Noise elimination ............................................ 20
Auto clock setting ........................................... 21
Manual clock setting....................................... 23
Loading and Unloading a Cassette Tape ....... 24
Advanced Function of DVD section
Parental control .............................................. 46
Temporary disabling of rating level by DVD
disc ................................................................. 47
Setting menu language .................................. 48
Setting subtitle language ................................ 49
Setting audio soundtrack language ................ 50
Setting surround sound .................................. 50
Setting the aspect ratio of TV screen ............. 51
Setting on Screen display .............................. 52
Status display of Disc ..................................... 52
Language Code List ....................................... 53
Tape Playback operation
Cassette tape Playback ................................. 25
Special playback ............................................ 26
ZERO RETURN function................................ 27
Video Index Search system ........................... 27
Recording
Recording a TV program ................................ 28
Instant Timer Recording (ITR)........................ 30
Timer Recording............................................. 31
Additional information
Problems and troubleshooting ....................... 54
Video head cleaning....................................... 55
Specifications .................................... back cover
Advanced Function of VCR section
Stereo Recording and Playback..................... 33
Separate Audio Program (SAP) ..................... 33
Duplicating a video tape................................. 34
Duplicating a disc material onto a video tape .... 34
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and functions
Front
VCR/DVD mode selector button
Cassette Loading Slot
PLAY button
STOP button
OPEN/CLOSE button
Disc tray
EJECT button
PLAY STOP
POWER
EJECT
OPEN/CLOSE
CH
REW FF
REC
DVD
VCR
VIDEO (M) L - AUDIO - R
VCR/DVD
Remote sensor
POWER
button
DVD indicator
CHANNEL +/– buttons
REW (Rewind) button
REC button
AUDIO (L/R)/
VIDEO IN jacks
VCR indicator
FF (Fast Forward) button
Rear
AC power cord
DVD OUTPUT
DIGITAL AUDIO
AUDIO
S-VIDEO
COMPONENT
OPTICAL
COAXIAL
IN
Y
VIDEO
L
(
)
ANT.
RF IN jack
R
PB/CB
L
AUDIO
OUT
(
)
TV
P
R/CR
R
DVD OPTICAL
DIGITAL AUDIO
OUT jack
RF OUT jack
CH.
3
4
3/4 Channel Selector Switch
DVD COAXIAL DIGITAL
AUDIO OUT jack
DVD/VCR common AUDIO (L/R)/VIDEO OUT
jacks
DVD AUDIO (L/R) OUT jacks
DVD S-VIDEO OUT jack
DVD COMPONENT OUT jacks
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
Display window
1
2
3
4
11
5
6
10
9
8
7
No. Display
Description
1
2
3
4
5
6
VCR
VCR mode
Playback (lights) / Auto resume (flashes)
Still picture
DVD disc is inserted.
DVD
CD
CD is inserted.
PM
Display for afternoon (lights out in the morning)
Clock display (colon[ : ] flashes)
10 : 00
01 : 00
2
Counter display by hour/minute at VCR/DVD / by minute/second at CD
Track number display for CD
7
TV channel display for VCR
C002
C036
L
CATV channel display
External input display
8
9
Timer recording display
Video tape is in the unit
Track display for CD
10
TRK
Normal recording display (flashes during Instant Timer Recording - ITR)
11 REC
Explanation for On-Screen-Symbol:
Playback
Skip chapter to reverse
direction
Zoom
Stop
Parental level locked
Parental level unlocked
Screen size: Normal TV
Screen size: PAN SCAN
Screen size: WIDE
Shows Prohibited act
Output sound for Video-CD
Still picture
Open or Close the tray
Auto resume
Frame advanced playback
Forward slowmotion
Direction button’s mark
A-B repeat
A B
Fast Forward playback
Review playback
Skip chapter to forward
direction
Subtitle language
Soundtrack language
Angle
Note:
Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Page
18,36
18
TV/VCR/DVD switch Switch to operate TV or VCR or DVD
POWER
TV
VCR
DVD
POWER
Power on/off
DVD MENU
MARKER
RETURN
OPEN/CLOSE
DISPLAY
A.TRK
Display menu of DVD software
Index for DVD
45
43
Remove DVD set up menu
Open or Close the tray
47
37
Change the front Display mode
Digital AUTO TRACKING
Set Subtitle of a DVD disc
Reset the counter to 00:00
Change playback angle of a DVD disc
27
26
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SUB TITLE
C. RESET
ANGLE
44
SEARCH
MODE
SUB TITLE
27
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
45
MODE
ZERO RETURN
SEARCH MODE
SP/EP
Stop the tape when the counter reaches 00:00 27
TV
POWER
Locating desired scene
39
28,30
40,41
39
Sets the tape speed for recording
Select playback mode
INPUT
PLAY MODE
ZOOM
Zoom (for DVD playback)
Select title of a DVD disc
TV VOL
TIMER
TV/VCR
TITLE
45
0
REPEAT A-B
0-9
Repeat playback between A and B (DVD/CD) 40
PLAY
Direct channel selection of TV
Input setting
20,28
39,41
46,47
31,32
18,29
10
STOP
C
Enter a password
SKIP
SKIP
TIMER
TV/VCR
TV POWER
INPUT
TV VOL +/–
REW
Set the unit to start recording at a preset time
.
/INDEX
/INDEX
Switches between TV and VCR
ENTER/
SELECT
SET
SET
Turn the connected TV on or off
Switch the connected TV to external mode
Adjust the connected TV’s volume
10
SET UP
MENU
CANCEL
10
C
Rewind/Review playback
Playback
25,26,38
25,37
PLAY
FF
Fast Forward/Forward search playback 25,26,38
REC
Recording
Stop
28,30,34
25,37
VCR/DVD/TV
STOP
PAUSE
Still picture/Recording pause on/off 26,29,34,38
SKIP
/
Skip chapter to forward or reverse direction
Search for the INDEX mark of a tape
38
27
INDEX
/
JVC TV Remote Control
TV/VCR CH +/–
Select channel of the connected TV or VCR
This Remote can control some functions
(TV POWER, NUMBER(0-9), INPUT, TV
VOL +/–, TV CH +/– and ENTER) of a
remote controllable JVC TV by slide TV/
VCR/DVD switch to TV.
10,28,30,34
/
Cursor buttons
Setting buttons
SET –/+
31,32
Manual tracking buttons in playback mode
26
/
Cursor buttons - To move Up in the VCR menu
you press the . To move Down in the VCR
NOTE:
•
It’s not possible to operate a unit not
equipped with a remote sensor.
menu you press the
.
ENTER
Enter information in the menu
Select option in the menu
Display menu of setup
•
•
This Remote can control a JVC TV only.
When you operate the VCR or DVD, the
TV/VCR/DVD switch must be slided to
VCR/DVD again. Otherwise the DVD/
VCR may not operate properly.
Since this unit is combined type of DVD
and VCR, the remote code of DVD is
individual. So please note that the DVD-
keys on the RCU of the other JVC
RECEIVER/TV isnoteffectiveforthisunit.
SELECT
SET UP MENU
CANCEL
18,19,36,48-52
32
Delete Timer program
Cancel input data in the setting mode 23,31,39,41
OSD
Display VCR or DVD operation status
Switches sound between mono, stereo and SAP
Change sound track language of DVD
Slowmotion playback
29,52
33
•
A.MONITOR
44
SLOW
26,38
26
SKIP SEARCH
Skip the unwanted short material of a tape
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Inserting Batteries
Open the battery compart-
ment cover in the direction of
the arrow.
Install two "AA" batteries (supplied),
paying attention to the polarity
diagram in the battery compartment.
Replace the compartment
cover.
2
3
1
Battery precautions
The precautions below should be followed when using batteries in this device:
1.Use only the size and type of batteries specified.
2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.
3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery
manufacturer’s directions.)
Remote control basics
• Press POWER to turn the DVD/VCR on or off.
• Make sure TV/VCR/DVD switch is set to VCR/DVD.
• Tap VCR CH + or VCR CH – to move through the channels one channel at a time.
• The VCR CH +/– and SET +/– are also used to navigate on-screen menu system.
• You can directly access specific channels using Number keys pad.
• Each press of VCR or DVD, switches the screen between the VCR screen (VCR mode) and the DVD screen
(DVD mode).
Operation
• Aim the remote control at the remote sensor and press control buttons
to operate.
• Operate the remote control within 30° angle on either side of the remote
sensor, up to a distance of Approx. 5 meters.
Approx. 5 meters
Change the custom code for remote control
If you operate this DVD/VCR with another JVC’s VCR simultaneously arranging them side by side, the both
recorders will react to this remote control. In this case, you can change the remote control and DVD/VCR to other
frequency (“ ”). Then you can operate only this DVD/VCR with this changed remote control.
When you purchased, the DVD/VCR and remote control have been set to the frequency-“ ”.
Example: Change frequency to
DVD/VCR:
Remote control:
WhileholdingVCR,
press 2(code: b) of
Number keys. (in
case of code: A,
press 1)
SEARCH
MODE
SUB TITLE
ZOOM
ANGLE
TITLE
In the POWER off mode,
press and hold PLAY for
more than 5 seconds. “b”
will appear on the display
and then disappear after
approx. 4 seconds.
SP/EP
PLAY
REPEAT
A-B
POWER
TV
MODE
VCR
DVD
TV
POWER
INPUT
PLAY STOP
OPEN/CLOSE
REW FF
REC
DVD
TV VOL
TIMER
TV/VCR
0
OPEN/
CLOSE
DVD MENU
MARKER
RETURN
NOTE:
• If the remote control has been set to b, the DVD/VCR also must be set to b. Otherwise, the DVD/VCR can not be
operated with this remote control.
• To reset to “A”, repeat above procedure. However press 1 instead of 2.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic connections
If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber,skip
ahead to page 14 for the proper connections.
ANTENNA TO DVD/VCR CONNECTION
The DVD/VCR must be connected "between" the antenna and the TV. First, disconnect the antenna from the TV
and connect it to the DVD/VCR.Then connect the DVD/VCR to theTV.Below are 3 common methods of connecting
an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection
diagram.
Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
DVD/VCR
1
IN
(ANT.)
75 ohm Coaxial Cable
OUT
(TV)
Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
2
3
DVD/VCR
Matching Transformer
300 ohm Input
IN
(ANT.)
75 ohm output
(not supplied)
OUT
(TV)
300 ohm Twin Lead (Flat) Wire
DVD/VCR
Separate VHF and UHF Antennas
Combiner
75/300 ohm Inputs
75 ohm output
(not supplied)
UHF
VHF
IN
(ANT.)
300 ohm Twin Lead (Flat) Wire
OUT
(TV)
75 ohm Coaxial Cable
NOTE: If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300
ohm inputs and one 75 ohm output.
NOTES: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the
antenna to the DVD/VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended.The use of
an outdoor type antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic connections
DVD/VCR TO TV CONNECTION
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow
the connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
TV
NOTE: If a VHF or UHF antenna is
used, set the TV/CATV
menu option to the "TV"
mode.
VHF/UHF IN
75 ohm Coaxial Cable (supplied)
TV with single 75 ohm VHF/UHF
antenna input
TV
NOTE: If a VHF or UHF antenna is
Splitter
75 ohm Input
75/300 ohm outputs
(not supplied)
used, set the TV/CATV
menu option to the "TV"
mode.
UHF
VHF
75 ohm Coaxial Cable
(supplied)
TV with 300 ohm UHFand 75 ohm VHF
antenna inputs
TV
NOTE: If a VHF or UHF antenna is
used, set the TV/CATV
menu option to the "TV"
mode.
UHF
Splitter
75 ohm Input
300 ohm outputs
(not supplied)
75 ohm Coaxial Cable
(supplied)
VHF
TV with 300 ohm UHF and 300 ohm VHF
antenna inputs
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CATV (CABLE TV) connections
Many cable companies offer services permitting reception of extra channels including pay or subscription channels.
This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable
company supplied converter box, except for those channels which are intentionally scrambled. If you subscribe to
a special channel which is scrambled, you must have a descrambler box for proper reception.
DVD/VCR
1
TV
IN
(ANT.)
VHF/UHF
Incoming Cable
IN (ANT)
OUT
(TV)
ALLOWS: Recording of nonscrambled channels.
*
*
*
Use of the programmable timer.
Recording of one channel while watching another.
DVD/VCR
2
Converter/
Descrambler
TV
IN
(ANT.)
VHF/UHF
IN (ANT)
Incoming
Cable
OUT
(TV)
ALLOWS: Recording of channels through the converter box
*
(scrambled and unscrambled).
NOTE:
Using the programmable timer to record only the
channel selected at the converter box.
*
To record from converter/descrambler,
DVD/VCR tuner must be tuned to the
converter output channel, usually
channel 3 or 4.
PREVENTS: Recording one channel while watching another.
*
*
Using the DVD/VCR tuner to select channels.
DVD/VCR
3
TV
IN
(ANT.)
VHF/UHF
IN (ANT)
Converter/Descrambler
Incoming Cable
OUT
(TV)
NOTE:
ALLOWS: Recording of nonscrambled channels.
*
If you are playing a tape or using the
tuner built into the DVD/VCR, the
converter must be set to the video
channel output of the DVD/VCR (either
3 or 4).
Use of the programmable timer.
Recording an unscrambled channel while watching
any channel selected at the converter box.
*
*
PREVENTS: Recording scrambled channels.
NOTE: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR
to the output of the Converter/Descrambler box, usually channel 3 or 4.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CATV (CABLE TV) connections
IMPORTANT: Make sure the TV/CATV menu option is set to the "CATV" mode.
This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled
programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult
your local cable company for more information concerning connection to their descrambler equipment. There are many
ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.
DVD/VCR
TV
Splitter
4
A/B Switch
VHF/UHF
IN (ANT)
IN
(ANT.)
Incoming
A
Cable
OUT
(TV)
B
Converter/Descrambler
ALLOWS: Recording of one channel while watching another.
*
*
*
Using the programmable timer to record only the channel selected at the converter box.
Recording of all channels through the converter box.
PREVENTS: Watching scrambled channels while recording another channel.
*
*
Using the DVD/VCR tuner to select channels.
DVD/VCR
5
TV
Splitter
IN
(ANT.)
VHF/UHF
IN (ANT)
Converter/
Descrambler
A/B Switch
Incoming
Cable
OUT
(TV)
A
B
ALLOWS: Recording of nonscrambled channels.
*
Recording of one channel while watching another.
Watching premium channels through the converter while recording nonscrambled channels.
Using the programmable timer.
*
*
*
PREVENTS: Recording scrambled channels.
DVD/VCR
Converter/
Descrambler
6
TV
Splitter
IN
(ANT.)
VHF/UHF
IN (ANT)
Incoming
Cable
OUT
(TV)
Converter/
Descrambler
A/B Switch
A
B
ALLOWS: Recording of all channels through the converter box.
*
*
Recording a scrambled or unscrambled channel while watching another (scrambled or
unscrambled) channel.
Using the programmable timer to record only the channel selected at the converter box.
PREVENTS: Using the DVD/VCR tuner to select channels.
*
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback Connection
The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent
on the model and features of each component. Check the Owner's Manual provided with each component for the
location of video and audio inputs and outputs.
Connect to a TV with Audio/Video Output
Use the supplied AUDIO/VIDEO Cord.
TV
Audio (L) Output Video Output
DVD/VCR
DVD OUTPUT
DIGITAL AUDIO
AUDIO
S-VIDEO
COMPONENT
OPTICAL
COAXIAL
IN
Y
L
VIDEO
(
)
ANT.
R
PB/CB
L
AO
OUT
(
)
T
V
PR/CR
R
CH.
3
4
To Video
Input
To Audio (R) Input
To Audio (L) Input
Audio (R) Output
AUDIO/VIDEO Cord (supplied)
Connect to a TV with S-Video Output
TV
S-Video Cord (not supplied)
DVD/VCR
DVD OUTPUT
DIGITAL AUDIO
AUDIO
S-VIDEO
COMPONENT
OPTICAL
COAXIAL
IN
Y
L
VIDEO
(
)
ANT.
R
PB/CB
L
AUDIO
OUT
(
)
T
V
P
R/CR
R
CH.
3
4
To S-Video Input
To Audio (R) Input
To Audio (L) Input
S-Video Output
Audio (L) Output
Audio (R) Output
AUDIO Cord (not supplied)
Connect to a BS TUNER
VHF/UHF
Antenna
TV
Satellite
Antenna
75 ohm Coaxial Cable (not supplied)
To ANT. Input
DVD/VCR
ANT. Input
BS Tuner
DVD OUTPUT
DIGITAL AUDIO
AUDIO
S-VIDEO
COMPONENT
OPTICAL
COAXIAL
IN
Y
L
VIDEO
(
)
ANT.
R
P
B/CB
L
AUIO
OUT
(
)
T
V
P
R/CR
R
CH.
ANT.
3
4
Output
Video Output
ANT. output
75 ohm Coaxial
Cable (supplied)
Audio (L) Output
To ANT.
Input
Audio (R) Output
AUDIO/VIDEO Cord (supplied)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback Connection
Connect to a Stereo Amplifier with Audio Output
If your TV has a COMPONENT VIDEO IN jack, you can connect the DVD/VCR to the TV with a COMPONENT
cable (not supplied) as shown below. COMPONENT VIDEO output jack can send higher-quality video signal to a
TV than S-Video output.
COMPONENT VIDEO Cord (not supplied)
To Component
To
Video Output
Component
Video Input
AUDIO/VIDEO Cord (supplied)
To Audio/Video Input
To Audio/Video Output
DVD/VCR
Stereo Amplifier
DVD OUTPUT
DIGITAL AUDIO
AUDIO
S-VIDEO
COMPONENT
OPTICAL
COAXIAL
IN
Y
L
VIDEO
(
)
ANT.
R
PB/CB
L
AUDIO
OUT
(
)
T
V
PR/CR
R
CH.
3
4
TV
Audio (L) Output
Audio (R) Output
To Audio (L) Input
To Audio (R) Input
AUDIO Cord (not supplied)
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems
such as Dolby Digital and DTS by using the Optical or Coaxial Digital Output.
Use this connection to connect an:
• AV amplifier with built-in *Dolby Digital decoder
• AV amplifier with built-in *DTS decoder
Video cord (not supplied)
To Video
DVD/VCR
Input
Video Output
DVD OUTPUT
TV
DIGITAL AUDIO
AUDIO
S-VIDEO
COMPONENT
OPTICAL
COAXIAL
IN
Y
L
VIDEO
(
)
ANT.
R
P
B/CB
L
AUDIO
OUT
(
)
T
V
PR/CR
R
CH.
3
4
NOTE:
AV Amplifier with
built-in various
decoder as above
You may connect to a TV with a
Component video cable(not supplied) or
S-Video cable(not supplied) instead of
a video cable(not supplied).
Coaxial digital
Audio Output
Coaxial digital cable
(not supplied)
Connecting the optical digital cable
You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital
cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
NOTE:
•
The OPTICAL, COAXIAL, AUDIO L/R, S-VIDEO and COMPONENT jacks are useful only for DVD section. The
VHS signal is output only from the composite jack(DVD/VCR VIDEO OUTPUT) and UHF/VHF OUT.
When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV
Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the
speakers to be damaged.
•
•
•
Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital input
connector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs may
cause such a high level of noise that it may be harmful to your ears and damage your speakers.
DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder is
necessary.
•
•
When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.
Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Video Channel / Setting the language
When a TV is connected with the 75 ohm coaxial cable only.
Setting the Video Channel
To view playback of a recorded tape,
Press POWER to turn on the DVD/VCR.
or to watch a program selected by
the VCR's channel selector, the TV
must be set to channel 3 or 4 (video
channel).
1
Slide TV/VCR/DVD switch to VCR/DVD. Then press VCR to
2 select the VCR mode. The VCR indicator on the front panel
will light.
Set the 3/4 Channel selector switch on the rear panel to CH
3 or 4.
3
POWER
TV
VCR
DVD
Turn ON the TV and set to CH 3 or 4 to correspond with the
channel selected in step 3.
4
Press TV/VCR to select the VCR position.
5 The VCR indicator will appear in the display.
Select any channel to receive a TV station in your area.
The channel number will appear on the screen for about
4 seconds.
6
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
For a push-button TV tuner
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
If CH 3 or 4 corresponding to the video channel cannot be tuned
on your TV, proceed as follows: set the VCR 3/4 channel selector
and the TV to CH 3 or 4, play back a prerecorded tape and tune
the TV to receive a sharp color picture from the video cassette
recorder. Refer to your TV owner's manual for details.
TV
POWER
INPUT
TV VOL
TIMER
TV/VCR
0
Setting the language
PLAY
You can choose from three different languages (English,
French and Spanish) for the on-screen displays.
STOP
C
Press SETUP MENU,
1
2
3
4
MENU
SKIP
SKIP
If you use the unit for the first time
and press SETUP MENU, instead
of the main menu screen on the
right the SYSTEM SET UP menu
screen in step 2 may appear.
TIMER REC SET
AUTO REPEAT
SAP
SURROUND
CH SET UP
SYSTEM SET UP
/INDEX
/INDEX
ON OFF
ON OFF
ON OFF
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
〈+/-/ENTER/MENU〉
C
Press
or
to select the
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
AUTO CLOCK
STANDARD TIME
“LANGUAGE” option, then press
ENTER.
NOTE:
•
ON OFF
If the unit does not operate properly,
or No key operation (by the unit
and/or the remote control): Static
electricity, etc., may affect the player's
operation. Disconnect the AC power
cord once, then connect it again.
If no buttons are pressed for more
than 60 seconds,the MENU screen
will return to normal TV operation
automatically.
DAYLIGHT SAVING TIME
〈+/-/ENTER/MENU〉
Press
or
toselectthedesired
language: English (ENGLISH),
Spanish (ESPAÑOL) or French
(FRANCAIS), then press ENTER.
•
•
Both the VCR and the DVD have their
own menu options (See page 36).
Press SETUP MENU until the MENU screen is cleared.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner Setting
This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to
the next channel set into memory, skipping over unwanted channels. Before selecting channels, they
must be programmed into the DVD/VCR’s memory. In addition to normalVHF and UHF channels, this DVD/
VCR can receive up to 113 Cable TV channels. To use this DVD/VCR with an antenna, set the TV/CATV
menu option to the TV mode. When shipped from the factory, this menu option is in the CATV mode.
Preparation:
POWER
TV
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
will light)
VCR
DVD
TV/CATV Selection
Press SETUP MENU. The VCR menu screen will appear.
1
Press
or
to select CH SET UP, then press ENTER.
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
Press
CATV” option.
or
to select the “TV/
CH SET UP
2
3
4
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV CATV
AUTO CH MEMORY
ADD/DELETE
TV
POWER
〈+/-/ENTER/MENU〉
INPUT
TV VOL
Then press ENTER to select the
TV or CATV mode. The arrow
indicates the selected mode.
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
TIMER
TV/VCR
0
PLAY
STOP
C
TV
- VHF/UHF channels
〈+/-/ENTER/MENU〉
CATV - CABLE TV channels
SKIP
SKIP
/INDEX
/INDEX
Press SETUP MENU until the menu screen is cleared.
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
C
Setting channels automatically
The VCR can receive a maximum of 181 channels by
presetting the channels into memory.
Repeat above step 1 and press
CH SET UP
1
VCR/DVD/TV
or
to select AUTO CH
TV CATV
AUTO CH MEMORY
ADD/DELETE
MEMORY.
〈+/-/ENTER/MENU〉
NOTE:
You can not select "CH SET UP" if you
set the channel to "L".
Then press ENTER.
2
CH 002
The auto tuning will start. The
channel display will count up and
when finished, the screen returns
to normal.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
To ADD/DELETE channels / Noise elimination
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
To ADD/DELETE channels
You can add the channels you want
or delete the channels you do not
want manually.
will light)
POWER
TV
Repeat the step 1 on page 19.
VCR
DVD
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
1
2
Then press
or
to select the
“ADD/DELETE” option and press
ENTER.
〈+/-/ENTER/MENU〉
OPEN/
CLOSE
To Add or Delete desired channels
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
1
Press Number keys or
/
SEARCH
MODE
SUB TITLE
ADD
CH 003
to select a channel number
you want to add or delete.
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
2
To add channels
POWER
Press ENTER until “ADD”
appears on the screen to set
to add the unmemorized
channel.
〈+/-/0-9/ENTER/MENU〉
INPUT
TV VOL
TIMER
TV/VCR
0
To delete channels
Press ENTER until “DELETE” appears on the screen to
set to delete the channel from memory. The channel
number will blink.
PLAY
STOP
C
3
Repeat 1 to 2 to add or delete other channel.
SKIP
SKIP
/INDEX
/INDEX
Press SETUP MENU until the menu screen is cleared.
3
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
C
Noise elimination
When you don't want to receive a weak signal broadcast, the
Blue back screen can be obtained by selecting the NO NOISE
BACKGROUND "ON". When the unit is shipped from the
factory, the NO NOISE BACKGROUND is set to the "ON".
VCR/DVD/TV
Repeat the steps 1~2 on page 18 and press
NO NOISE BACKGROUND.
or
to select
1
Press ENTER to select the ON
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
2 position.
AUTO CLOCK
ON OFF
STANDARD TIME
DAYLIGHT SAVING TIME
〈+/-/ENTER/MENU〉
Press SETUP MENU until the menu screen is cleared.
3
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto clock setting
The Auto Clock feature enables the automatic clock setting and updating, and also to set the Time Zone
and Daylight Saving Time by receiving XDS (Extended Data Service) information carried on the channel
signal.
Preparation:
•
You must set the antenna connection before the AC cord plug is
inserted into the AC outlet.
Make sure the AUTO CH MEMORY(on P.19) is done.
•
Auto clock setting
POWER
TV
VCR
DVD
WAIT 30 MINUTES! when the power switch is off, after the
connections of the antenna and the power plug. Because the Auto
Clock setting feature is activate.
After the clock is set automatically, you may have to set the Time
Zone and Daylight Saving Time.
Press POWER to turn on the DVD/VCR after the Auto Clock operation
completed.
•
•
•
When shipped from factory, the AUTO CLOCK option is set to ON position.
If you turn the DVD/VCR on during Auto Clock setting, the clock is not set.
With cable box connection, if the Auto Clock Setting is unsuccessful,
please select the PBS channel carrying the XDS information, then
turn the DVD/VCR off. After 30 minutes, turn the DVD/VCR on, and
if the clock is not set automatically, set the clock manually. (See page 23)
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
POWER
Time Zone setting (STANDARD TIME)
INPUT
In the rare event that you live within broadcast range of two
stations in two different time zones, the DVD/VCR may recognize
the wrong station for the AUTO CLOCK set.
TV VOL
To correct the situation:
TIMER
TV/VCR
0
Preparation:
• Turn ON the TV.
PLAY
• When a TV is connected with an audio/video cable, select the video
input mode on the TV.
• When a TV is connected only with an antenna cable, set to the
video channel 3 or 4. Then select VCR position with TV/VCR.
• Make sure the VCR mode has been selected. (Is the VCR indicator
being light?) (see steps 1~2 on page 18)
STOP
C
SKIP
SKIP
/INDEX
/INDEX
ENTER/
SELECT
SET
SET
Press SETUP MENU. The VCR menu screen will appear.
1
Press
or
to select the SYSTEM SET UP menu, then
SET UP
MENU
CANCEL
press ENTER.
C
Press or
“STANDARD TIME” option, then
press ENTER.
to select the
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
2
AUTO CLOCK
ON OFF
STANDARD TIME
DAYLIGHT SAVING TIME
VCR/DVD/TV
〈+/-/ENTER/MENU〉
Press
or
to select your Time
STANDARD TIME
3
4
Zone, then press the ENTER.
ATLANTIC
CENTRAL
PACIFIC
HAWAII
EASTERN
MOUNTAIN
ALASKA
NOTE:
• After Auto Clock setting, in some case
the clock may display the other time
zone’s. You can correct the clock by
selecting your Time Zone setting
above.
• When the clock is not set or you set
the clock manually, Time Zone setting
is not available.
AUTO
〈+/-/ENTER/MENU〉
Press SETUP MENU until the MENU screen is cleared.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto clock setting
Daylight saving time setting
You can set the Daylight saving
time automatically or manually.
Preparation:
Turn ON the TV.
•
•
When a TV is connected with an audio/video cable, select the
video input mode on the TV.
When a TV is connected only with an antenna cable, set to the
video channel 3 or 4. Then select VCR position with TV/VCR.
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
will light)
•
•
POWER
TV
VCR
DVD
Repeat the step 1 on page 21 and
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
1
2
press
or
to select DAYLIGHT
SAVINGTIME,thenpress ENTER.
ON OFF
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
〈+/-/ENTER/MENU〉
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
Press
or
to select one of
DAYLIGHT SAVING TIME
POWER
the options, then press ENTER.
ON
INPUT
OFF
AUTO
for manual setting
(forward one hour)
for manual setting
(back one hour)
for automatic setting
(read XDS in the signal)
ON:
〈+/-/ENTER/MENU〉
TV VOL
OFF:
AUTO:
TIMER
TV/VCR
0
PLAY
STOP
C
When you want to set the Daylight Saving Time manually, on
the first Sunday in April you set to “ON”, and on the last
Sunday in October you set to “OFF”.
SKIP
SKIP
/INDEX
/INDEX
ENTER/
SELECT
SET
SET
NOTES:
SET UP
MENU
CANCEL
When shipped from factory, the DAYLIGHT SAVING TIME
option is set to AUTO position.
•
C
• When the clock is not set, Daylight Saving Time setting is not
available.
•
When there is no Daylight Saving Time in your area, always
select OFF position in step 2.
VCR/DVD/TV
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual clock setting
You must set the date and time
manually for timer recordings and
Daylight Saving Time if the Auto
Clock process did not set them
correctly.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
will light)
EXAMPLE: Setting the clock to "8:30 AM" October, 23 (WED),
POWER
TV
VCR
DVD
2002.
Press SETUP MENU. The VCR menu screen will appear.
1
Press
or
to select the
2
3
4
MENU
TIMER REC SET
AUTO REPEAT
SAP
SURROUND
CH SET UP
SYSTEM SET UP
SYSTEM SET UP menu, then
press ENTER.
ON OFF
ON OFF
ON OFF
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
〈+/-/ENTER/MENU〉
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
Press
or
to select the
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
AUTO CLOCK
STANDARD TIME
POWER
“CLOCK SET” option, then press
ENTER.
INPUT
ON OFF
DAYLIGHT SAVING TIME
TV VOL
〈+/-/ENTER/MENU〉
TIMER
TV/VCR
0
PLAY
Press
or
to set the month,
STOP
C
then press ENTER button.
SKIP
SKIP
/INDEX
/INDEX
ENTER/
SELECT
SET
SET
SET UP
MENU
To make corrections any time during the process
CANCEL
Press CANCEL repeatedly until the item you want to change
C
blinks, then press
or
.
Set the day, year and time as in
step 4.
5
6
VCR/DVD/TV
NOTE:
After a power failure or disconnection
of the power, the timer settings will be
lost. In this case, reset the present time.
After setting the clock, date and
time starts functioning
automatically.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and Unloading a Cassette Tape
Use only video cassette tapes marked
and
.
•
•
•
Cassettes marked “VHS” (or “S-VHS”) can be used with this video cassette recorder. However, S-VHS recording
is not possible with this model.
This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS
recordings with regular VHS resolution.
HQ VHS is compatible with existing VHS equipment.
Loading
Insert the cassette tape with its labeled side facing up
and the erase prevention tab positioned at your left. An
inverted cassette tape cannot be inserted.
Push the center of the tape until it is automatically
inserted.
VCR
Erase prevention tab
Automatic power ON
When you insert a cassette tape the VCR power will turn ON automatically.
Automatic playback
When loading a cassette tape without an erase prevention tab, playback will start automatically.
Unloading
Press EJECT on the unit.
Remove the cassette tape.
1
2
Automatic tape eject
This VCR will automatically rewind the tape when the tape has ended. And when the tape is rewinded to its
beginning, the cassette tape will be ejected automatically.
To prevent accidental erasure
To record again
Removetheerasepreventiontabwithascrewdriver.
Cover the hole with a piece of adhesive tape.
Screwdriver
Erase prevention tab
Adhesive tape
Tape speed and maximum recording time
Video cassette tape
Tape Speed
T-160
2-2/3 hours
8 hours
T-120
2 hours
6 hours
T-90
T-60
T-30
SP (Standard Play)
EP (Extended Play)
1-1/2 hours
4-1/2 hours
1 hour
3 hours
30 minutes
1-1/2 hours
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Cassette tape Playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
will light)
Load a prerecorded tape
1
POWER
TV
VCR
DVD
(When loading a cassette tape
without the erase prevention
tab, playback will start auto-
matically).
To start playback
2
Press PLAY.
Playback will start.
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
"
" will appear on the screen
SEARCH
MODE
SUB TITLE
for about 4 seconds.
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
POWER
To stop playback
INPUT
Press STOP once.
The tape will stop but remain
fully loaded and ready to play.
TV VOL
TIMER
TV/VCR
0
"
" will appear on the screen
for about 4 seconds.
PLAY
STOP
C
To rewind the tape or forward it rapidly
SKIP
SKIP
/INDEX
/INDEX
Stop the playback or recording with STOP.
To rewind the tape:
To forward the tape:
Press FF.
ENTER/
SELECT
SET
SET
Press REW.
SET UP
MENU
CANCEL
C
VCR/DVD/TV
To stop the tape-winding, press STOP. To switch to playback
directly (without STOP), press PLAY.
Forward/Reverse picture search mode
NOTE:
When the tape is being winded, you can switch to picture search
mode (see next page). To do this, press REW or FF and hold it
down.Theunitwillresumethetapewindingassoonasthebutton
is released.
•
This VCR selects the playback tape
speed SP or EP automatically.
•
The Cassette tape and DVD disc can
be played back simultaneously. If you
press VCR or DVD, the tape playback
and DVD playback alternate with each
other on the screen.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Special playback
Picture Search
Repeat playback
The entire video tape will be played until its end.The
tape will then automatically rewind to the beginning and
the playback will be repeated.
Reverse picture search function
Press REW x 1 or x 2 during the playback.
Forward picture search function
Press SETUP MENU. Press
AUTO REPEAT.
or
to select
Press FF x 1 or x 2 during the playback.
1
2
To return to playback: Press PLAY.
Then press ENTER to
MENU
TIMER REC SET
AUTO REPEAT
SAP
SURROUND
CH SET UP
select [ON] or [OFF].
If [ON] is selected, the
playback will be
repeated endlessly.
ON OFF
ON OFF
ON OFF
Still Picture
Press PAUSE during playback. To resume normal
playback: Press PLAY.
SYSTEM SET UP
〈+/-/ENTER/MENU〉
Slow Motion
Press SETUP MENU until the menu screen is
cleared.
if you press OSD, " " will appear on the screen.
3
4
During playback press SLOW.
To return to playback: Press PLAY or SLOW.
Slow tracking and vertical lock adjustment
If noise bars appear in the picture during slow motion,
press the SET + or – to reduce the noise bars.
If the still picture jitters excessively, press SET + or –
to stabilize the still picture.
To start the playback, press PLAY.
The playback will be repeated endlessly.
To cancel repeat mode:
Follow the above step 1, then press ENTER to select
the OFF position. Press SETUP MENU to return to
the TV.
Frame by Frame picture
Press PAUSE during playback.
Press SLOW one by one: The picture advances frame
by frame.
To return to playback: Press PLAY or PAUSE.
Skip Search
Adjusting tracking condition
Each time you press SKIP SEARCH while a tape is
playing, the unit will fast-forward ahead 30 seconds
on the tape.You may press the button up to six times
in a row to move 180 seconds (three minutes) ahead.
Automatic tracking adjustment
Whenever you insert a tape and start playback,
automatic tracking starts working and continuously
analyzes the signal to enable optimum picture quality
during playback.
1 press: 30 seconds of tape
2 presses: 60 seconds of tape
3 presses: 90 seconds of tape
For example:
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, press SET +/– to eliminate the noises.
“MANUAL TR.” will appear. Press it briefly for a fine
adjustment, or press and hold for a coarse adjustment.
•
Press A.TRK to reactivate automatic tracking again.
“AUTO TR.” will appear.
Note:
The audio output is muted during SPEED SEARCH,
STILL, FRAME ADVANCE and SLOW MOTION.
•
• During picture search mode there will be noise bars
which are caused by the system.
• The Special Playback will automatically change to
playback after approx. 5 minutes to protect the video
tape against excessive wear.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
ZERO RETURN function / Video Index Search system
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
ZERO RETURN function
This function makes tape-rewinding
stop at the counter 00:00:00 position
automatically.
will light)
OPEN/
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
CLOSE
Press OSD.
The counter display shows the tape
running time during playback or
1
2
3
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
recording.
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
VCR
TV
POWER
Press C. RESET at the desired tape po-
sition. The counter display will be reset
to the "00:00:00" position (e.g. the
INPUT
begining of recording).
TV VOL
VCR
TIMER
TV/VCR
0
PLAY
Press STOP when playback or recording is finished.
Press ZERO RETURN.
The tape will be rewinded or fast forwarded and automatically
stop at the ”00:00:00” position.
STOP
C
SKIP
SKIP
/INDEX
/INDEX
The DISPLAY-button
Press DISPLAY. The clock and tape counter
ENTER/
SELECT
SET
SET
VCR
SET UP
MENU
alternate with each other in the display.
CANCEL
C
VCR
NOTE for Counter Display:
Video Index Search system
This function enables you to locate the beginning of any
recording made on the VCR.
•
Ifyourewindthetapebeyond“00:00:00”,
a minus sign (“–”) will be displayed in
front of the time counter.
•
•
When you load a tape, the counter will
reset to “00:00:00”.
The counter does not function on
nonrecorded (blank) sections of the
tape.Whenyourewind,fastforwardor
play tapes through blank sections, the
counter stops.
Recording an INDEX MARK
The Index Search function automatically
records an INDEX mark on the tape
whenever a recording is initiated.
CH 001
INDEX
NOTE for Video Index Search system:
Index Search
Press INDEX
mode.
For Succeeding programs: Press INDEX
For Preceding programs: Press INDEX
(Additional press increases the INDEX NO.
up to 9.)
•
When you record an INDEX mark at
the very beginning of the tape, the
mark may not be found.
During INDEX search, the tape may
stop and begin to play at a slightly
different location.
or
during stop or play
+3
•
.
.
•
•
INDEX may not function properly with
old or worn out video tapes.
INDEX marks may not be found if it is
extremely close to the point where the
search began.
In recording, if you stop recording
temporarily, the INDEX mark is not
recorded on the tape.
When the INDEX
or
is pressed, the
or
is displayed
unit starts searching the INDEX NO.
selected and finds the portion, then
playback starts automatically.
INDEX NO. (up to 9)
•
To stop the Index Search, press STOP.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a TV program
Recording and viewing the
same TV program
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
will light)
Load a cassette tape with the erase
prevention tab intact.
The VCR will automatically turn on.
POWER
TV
VCR
DVD
1
Press SP/EP to select the desired tape
2 speed SP or EP.
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
The tape counter and SP or EP will
appear on the screen for about 4
ZERO RETURN
SEARCH
MODE
SUB TITLE
00 : 00 : 00 SP
SP/EP
seconds.
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
POWER
Set the TV/CATV option to the appropriate position (See page
19).
3
INPUT
TV
- VHF/UHF channels
CATV - CABLE TV channels
TV VOL
TIMER
TV/VCR
0
Press Number keys or VCR CH +/– to select the channel to
4 be recorded.
PLAY
1-9
Press 0 twice and then 1-9 as required. Example: To
select 2, Press “002”.
Press 0 first and then the remaining 2 digits in order
from left to right.
STOP
C
10-12
SKIP
SKIP
/INDEX
/INDEX
Example: Press 012 for “12”.
Press 2 digits in order.
CH 110
13-99
ENTER/
SELECT
Example: Press 22 for “22”.
SET
SET
100-125 Press the 3 digits in order.
SET UP
MENU
CANCEL
Example: Press 110 for “110”.
C
VHF/UHF/CATV CHANNELS
TV
CATV
VHF
2-13
VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36 (A) (W)
VCR/DVD/TV
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
01 (5A)
NOTE:
• Iftheerasepreventiontabisremoved,
the tape will eject when both the REC
and PLAY are pressed for recording.
• If you wish to watch the DVD playback
during the normal recording on VCR,
press DVD to change to DVD mode
and perform the DVD playback(see
P.37).
On the VCR, press REC.
5 Or on the Remote, while holding REC,
CH 110
press PLAY.
" will appear on the screen for
"
INDEX
about 4 seconds and “REC” will
appear on the display.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a TV program
To stop recording
Press STOP to stop recording.
" will appear on screen for about 4
"
seconds.
To stop recording temporarily
POWER
TV
VCR
DVD
Press PAUSE to avoid recording unwanted
material. Press again to continue the
recording.
"
" will appear on screen for about 4
seconds.
NOTE:
OPEN/
CLOSE
•
The pause function will be released after 5 minutes to prevent damage
to the tape or the VCR. The VCR will change to the STOP mode.
You can select a recording channel in the recording pause mode.
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
•
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
Recording one program while watching another
POWER
While the VCR is recording, press TV/VCR to select the TV position.
The “VCR” will go off and recording will continue.
INPUT
Select the TV channel you want to watch by using the TV channel
selector. If the connected TV is JVC’s, use TV CH +/– after slide TV/
VCR/DVD switch to TV.
TV VOL
TIMER
TV/VCR
0
NOTE:
PLAY
Some CATV hookups do not permit viewing one channel while
recording another. See pages 14,15.
STOP
C
SKIP
SKIP
To Display VCR operation Status
/INDEX
/INDEX
Press OSD. The clock, day of the week and more information will be
indicated.
ENTER/
SELECT
SET
SET
While watching TV
DAY OF THE WEEK
SET UP
MENU
CANCEL
C
CLOCK
8 : 47AM MON
STEREO SAP
CH 125
CHANNEL
STEREO AND
SEPARATE AUDIO
PROGRAM (SAP)
00 : 00 : 00 SP
TAPE SPEED
VCR/DVD/TV
REAL TIME COUNTER
While operating a tape
Auto Rewind feature
This VCR will automatically rewind the
tape when the tape has ended (except
during ITR and TIMER REC). It will also
eject the tape.
OPERATING
MODE
8 : 30AM MON
HI-FI
CH 125
HI-FI STEREO
AUTO REPEAT
TAPE IN
00 : 00 : 00 SP
To cancel the display: Press OSD until all indicators disappear.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Timer Recording (ITR)
The Instant Timer Recording
feature provides a simple and
convenient way to make a timed
recording.
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode. (The VCR indicator
will light)
Example: Instant Timer Recording for 30 minutes.
POWER
TV
VCR
DVD
Load a cassette tape with the erase
prevention tab intact.
The VCR will automatically turn on.
1
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
Press SP/EP to select the desired tape
ZERO RETURN
2 speed SP or EP.
SEARCH
MODE
SUB TITLE
The tape counter and SP or EP will
appear on the screen for about 4
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
00 : 00 : 00 SP
seconds.
TV
POWER
INPUT
Set the TV/CATV option to the appropriate position (See page
19).
3
TV
- VHF/UHF channels
TV VOL
CATV - CABLE TV channels
TIMER
TV/VCR
0
PLAY
Press Number keys or VCR CH +/– to
4 select the channel to be recorded.
CH 110
STOP
C
SKIP
SKIP
/INDEX
/INDEX
ENTER/
SELECT
SET
SET
Press REC on the VCR or while holding REC, press PLAY on
the Remote to begin recording. Press REC on the VCR again to
stop recording after 30 minutes. Each additional press of REC
will increase recording time as shown in the chart below, up to a
maximum of 5 hours.The ITR and recording time will appear on
the screen for about 4 seconds. And, REC will keep blinking in
the display.
5
SET UP
MENU
CANCEL
C
Press Recording time Press
Recording time
ITR 0 : 30
CH 125
VCR/DVD/TV
NORMAL REC 6 times
3:00
once
4:00
twice
0:30
1:00
1:30
2:00
7 times
8 times
9 times
5:00
3 times
4 times
5 times
INDEX
NORMAL REC
NOTE:
If you wish to watch the DVD playback
during the ITR, press DVD to change to
DVD mode and perform the DVD
playback(see P.37).
To cancel ITR
Press STOP or turn off the power.
" will appear on screen for about 4
seconds.
"
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer Recording
Timer recording can be programmed
on-screen with the remote control.
The built-in timer allows automatic
unattended recording of up to 8
programs within 1 month.
Preparation:
Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press VCR to select the VCR mode.
•
• Load a cassette tape with the erase prevention tab intact.
• Press OSD to verify that the time and date are correct.(see page
29).
OPEN/
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
CLOSE
Example: Program a timer recording for the 26th day, channel 125
(CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: EP).
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
Press SETUP MENU. Select the
TIMER REC SET option, then press
ENTER.
MENU
TIMER REC SET
AUTO REPEAT
SAP
SURROUND
CH SET UP
SYSTEM SET UP
ZOOM
TITLE
MODE
1
ON OFF
ON OFF
ON OFF
TV
POWER
INPUT
〈+/-/ENTER/MENU〉
Press SET + or – to select one of the
DATE
START END
CH
TV VOL
2 program line, then press ENTER.
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
—
—
—
—
—
—
—
—
—
—
TIMER
TV/VCR
0
—
—
—
PLAY
—
—
—
〈+/-/ENTER/CANCEL/MENU〉
STOP
C
Press SET + or – to select the date,
then press ENTER.
DATE
START END
CH
3
26(SU)
— : — — — : — — — —
—
—
—
—
—
—
—
—
—
SKIP
SKIP
— — — — — —— : — — — : — — — —
—
/INDEX
/INDEX
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
—
—
—
—
ENTER/
SELECT
SET
SET
—
—
〈+/-/ENTER/CANCEL/MENU〉
SET UP
MENU
CANCEL
Set the start time, end time, channel
C
DATE
START END
CH
4 and tape speed as in step 3.
2—6—(S—U—) —1——1:0: —0P—M 1—1:3: —0P—M125 EP
— —
—
—
—
—
—
—
—
—
— — — — — —— : — — — : — — — —
—
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
—
—
NOTE:
—
NOTE:
—
• PressCANCELtomovecursorbackward
for correction.
• To record from external source set the
channel to "L". "L" will appear next to CH
125 (or 69).
—
• Iftheclocksymbol( )blinkswhenthe
timerrecordingended,theTVprogram
has not been completely recorded
becauseofaninsufficienttapesupply.
In this case, press TIMER to cancel
the timer program or press EJECT to
remove the cassette tape.
• During timer recording standby mode,
the VCR mode cannot be selected. To
use the VCR, press TIMER at first,
then press VCR to change to VCR
mode. After you use the VCR, press
TIMER again to put the VCR into timer
recording standby mode.
• If you press TIMER during timer
recording, the recording operation will
be interrupted. If you press TIMER
againwithintheprogrammedtime,the
recording operation will start again.
• After a power failure or disconnection
of the power plug, all programmed
recording settings and time display
will be lost upon resumption of power.
Inthiscase,resettheclock(seepages
21-23) and reprogram any timer
recordings.
〈+/-/ENTER/CANCEL/MENU〉
To enter other programs, repeat step
2 through 4.
DATE
START END
CH
5
2—6—(S—U—) —1——1:0: —0P—M 1—1:3: —0P—M125 EP
— —
—
—
—
—
—
—
—
—
— — — — — —— : — — — : — — — —
—
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
—
—
• To return to the normal screen,
press SETUP MENU twice.
—
—
—
〈+/-/ENTER/CANCEL/MENU〉
Press TIMER. The clock symbol( ) will appear on the display
and the VCR stands by for recording. At the same time, VCR
mode will change to DVD mode automatically. You can use
DVD even if the VCR is in the Timer recording mode.
If you do not use the DVD, turn the power off.
6
The timer recording will start at 5 seconds before the time you
predetermined.
NOTE:
•
If the clock symbol( ) does not appear on the display in spite
of the pressing of TIMER, the cassette may not have been
loaded yet.(see page 24)
•
If the cassette is ejected in spite of the pressing of TIMER , the
erase prevention tab of the cassette may have been
removed.(see page 24)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer-Recording
Timer Recording Special case
Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g.
MO-SA: Monday to Saturday) Timer recording
Confirmation / Cancellation of the Timer
Recording
If the Timer has been activated, press TIMER to
Follow the procedure of timer recording on the previous
page. At picture 3 press SET + or – repeatedly until the
desired setting appears. Then press ENTER.
1
deactivate the Timer. The clock symbol( ) will
disappear. Then press VCR to change to VCR
mode.
When you press SET – repeatedly, the indicator at
DATE will change as follows, in this case the today is
Friday.
To confirm Timer program:
2
At picture 1 on the
DATE
START END
CH
2—6—(S—U—) —1——1:0: —0P—M 1—1:3: —0P—M125 EP
previous page select the
TIMER REC SET option
and press ENTER.
— —
—
—
—
—
—
—
—
—
— — — — — —— : — — — : — — — —
—
The current day (Friday)
SU-SA (Sunday to Saturday)
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
—
—
—
—
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-TH (Weekly Thursday)
Then the timer program
list as right will appear on
the screen.
—
One month later
minus one day
〈+/-/ENTER/CANCEL/MENU〉
WKL-WE
(Weekly Wednesday)
To cancel Timer program:
3
4
Press SET + or – to
select the unnecessary
program, then press
CANCEL to cancel the
program.
DATE
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
START END
CH
—
—
—
—
—
—
—
—
—
DATE
START END
— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
CH
—
WKL-WE
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
〈+/-/ENTER/CANCEL/MENU〉
—
〈+/-/ENTER/CANCEL/MENU〉
PressSETUPMENUrepeatedlyuntiltheTV-picture
appears.
In case Timer programs-overlap
•
Do not overlap timer programs as portions of the
conflicting programs will be lost. The first recording
timehaspriorityoverthenextrecordingtimeasshown
in the diagram below.
NOTE:
•
If there are other timer record programs remaining,
TIMER must be pressed to reactivate the timer,
otherwise the remaining timer record programs will
be ignored.
•
•
You cannot confirm the Timer program during timer
recording operation.
You can also correct the programmed setting in
program confirm mode.
8 : 00
9 : 00
10 : 00
11 : 00
Program 1
Program 2
Deleted Parts
Program 3
At step 2 above, press ENTER to enter the program
input mode. Then press ENTER repeatedly until the
item you wish to correct
Non Recorded Portion Parts
Recording
Control Settings
Prog.1
Prog.2
Prog.3
DATE
START END
CH
2—6—(S—U—) —1——1:0: —0P—M 1—1:3: —0P—M125 EP
blinks. Thencorrectthedata
with SET + or –.
Then press SETUP MENU
repeatedly until the TV-
picture appears.
— —
—
—
—
—
—
—
—
—
— — — — — —— : — — — : — — — —
—
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
— — — — — —— : — — — : — — — —
—
—
—
—
—
〈+/-/ENTER/CANCEL/MENU〉
NOTE:
•
The daily/weekly recording can be made continu-
ously until the recording is canceled or the tape
reaches the end.
•
During timer recording the automatic rewinding
mechanism does not function.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo Recording and Playback / Separate Audio Program (SAP)
Stereo Recording and
When a MTS STEREO broadcast is
received, the word STEREO will appear
on the screen and the program can be
viewed or recorded in stereo.
The Hi-Fi STEREO recording procedure
is the same as for normal recordings.
Playback
The VHS Hi-Fi audio system permits high
fidelity recording of MTS STEREO TV
broadcasts.
STEREO
POWER
NOTE:
TV
VCR
DVD
WhenusingaCATVsystem, stereoTVprogramsmaybetransmitted
over a mono cable channel. In this case the word "STEREO" will not
appear and the sound will be in mono.
Output selection
When viewing an MTS STEREO TV program, or playing a prerecorded
VHS Hi-Fi STEREO videotape, press A. MONITOR to select how the
audio will be heard through the speakers. Normally set to the Hi-Fi
STEREO position, this button can be set to the MONO position if the
stereo broadcast or videotape audio is of poor quality. The "R" and "L"
positions allow the audio from the Right or Left Hi-Fi channel to be heard
over both TV speakers.This button has no effect when viewing a MONO
videotape orTV program.Each time when you press the button, OUTPUT
SELECTION display appears on the screen for several seconds. Refer
to the chart below.
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
POWER
OUTPUT
SOUND HEARD ON BOTH
INPUT
SELECTION SPEAKERS
STEREO
L ch
R ch
STEREO
TV VOL
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
TIMER
TV/VCR
0
MONO
PLAY
STOP
C
Separate Audio Program (SAP)
SKIP
SKIP
/INDEX
/INDEX
Your VCR is fitted with a SAP broadcast system which enables
you to switch to a separate audio program when viewing a
selected channel.
ENTER/
SELECT
SET
SET
This function applies only when the program is broadcast in
multi-languages through the SAP broadcast system.
SET UP
MENU
CANCEL
C
Press SETUP MENU. Then press
Then press ENTER to select [ON].
or
to select SAP.
1
2
MENU
TIMER REC SET
AUTO REPEAT
SAP
SURROUND
CH SET UP
ON OFF
ON OFF
ON OFF
Then press SETUP MENU until
the menu screen is cleared.
VCR/DVD/TV
SYSTEM SET UP
〈+/-/ENTER/MENU〉
NOTE:
Listening to SAP
• When playing back a tape that is not
recorded in Hi-Fi stereo mode, the
audio will automatically be monaural.
• When listening to a VHS Hi-Fi video
tape or MTS broadcast through the
VHF/UHF jack (Audio/Video cord not
connected), the sound will be
monaural.
When the VCR is turned on or a channel selection is made, make
certain the letters "SAP" appears on the screen.This means that the
"Separate Audio Program" broadcasting is available.
STEREO SAP
SAP
OR
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Duplicating a video tape/Duplicating a disc material onto a video tape
Duplicating a video tape
If you connect the VCR to another VCR or camcorder, you can duplicate a previously recorded tape.
Make all connections before turning on the power.
Load a blank cassette tape with the erase preven-
tion tab intact into the recording VCR.
Load a previously recorded tape into the playback
VCR or CAMCORDER.
Press REC on the recording VCR.
Or on the Remote, while holding REC, press PLAY.
Then press PAUSE.
1
2
3
4
Press PLAY button on the playback VCR or
CAMCORDER, then press PAUSE button.
5
6
Press SP/EP to select the desired tape speed SP
or EP.
It is recommended that you set the speed to the
SP mode on the recording VCR for best results.
Press PAUSE on both the VCRs simultaneously to
begin the duplicating process.
Press VCR CH + or – to select AUDIO/VIDEO input
position. "L" will appear in the
display.
Connection with Video camera
Connection with second Video recorder
Playback VCR
Playback Camcorder
To AV Jack
To VIDEO OUT
To AUDIO (R) OUT
To AUDIO (L) OUT
Recording VCR
AUDIO/VIDEO Cord (supplied)
Recording VCR
To AUDIO (R) IN
To AUDIO (L) IN
AUDIO/VIDEO Cord (not supplied)
To VIDEO IN
To AUDIO (R) IN
To AUDIO (L) IN
To VIDEO IN
For duplicating a previously recorded tape from a
camcorder, follow the camcorder manufacturer’s
instructions. A typical camcorder dubbing hookup
is shown above.
Duplicating a disc material onto a video tape
You can record disc material in DVD, Video CD, Audio CD, etc. onto a video tape with this DVD/VCR only.
If the DVD disc has a Copy-guard feature, the duplicating is not possible. A symbol mark “ ” will
appear on the screen for approx. 4 seconds. See page 37 for more information about the DVD playback.
Preparation:
• Load a cassette tape with the erase prevention tab
intact.
During disc playback, press REC on the VCR or
while holding REC, press PLAY on the Remote.
The duplicating will start.
3
•
•
Select the tape speed in the VCR mode. (see P.28)
Load a disc you wish to duplicate.
Note:
Press DVD to select the DVD mode. (The DVD
indicator will light)
1
You can set the duplicating time using the ITR-function.
At step 3 above press REC repeatedly until the desired
duplicating time appears on the screen.(P.30)
Press PLAY to start the disc playback.
2
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc
This unit applies to DVD discs from Region 1 only.
The loaded Disc (DVD, Video-CD, Audio-CD and MP3-CD) will be recognized automatically.
The suitable Disc-formats are: DVD, CD-R and CD-RW.
Do not play DVD-ROM, DVD-Audio, CDV, CD-G or Photo CD to prevent accidental erasure of prerecorded material.
Some DVDs are played back with a Copy guard system. In case of a dubbing on video tape, strong disturbance may
occur. This is not a defect of this DVD/VCR.
Title
When two or more movies are recorded on a disc,
DVD DISC
the disc is divided into two or more sections. Each
section is called a “TITLE”.
TITLE1
CHAPTER 1
TITLE2
CHAPTER 2
CHAPTER 1
CHAPTER 2
CHAPTER 3
Chapter
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Video-CD/Audio-CD
Video-CD/Audio-CD-Track
An Video CD or Audio CD can contain several items.
These are assigned to the tracks.
TRACK
1
TRACK
2
TRACK
3
TRACK
4
TRACK
5
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from center to edge.
• Do not wipe the disc round.
• Do not use liquid or aerosol cleaners.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting setup language
The setup language can be selected.
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
• When using an amplifier, switch on the amplifier.
POWER
TV
VCR
DVD
Press DVD to select the DVD
1
2
3
4
No Disc
mode. (The DVD indicator will
light)
“No Disc” will appear on the
screen.(IfaDVDdischasalready
loaded, the playback will start
automatically.)
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
Press SETUP MENU in the stop
mode. The SETUP MENU of
DVD will appear on the screen.
Language Picture
Parental
Other
Other
Other
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
Then press
or
to select
Other.
TV
POWER
/Enter/Setup/Return
INPUT
Language Picture
Parental
Press ENTER to select OSD
Language.
TV VOL
TIMER
TV/VCR
OSD Language English
0
PLAY
STOP
C
/Enter/Setup/Return
SKIP
SKIP
/INDEX
/INDEX
Language Picture
Parental
Press
and then press
or
to select desired language
(e.g. English), then press
ENTER.
ENTER/
SELECT
SET
SET
OSD Language English
English
Francais
Espanol
SET UP
MENU
CANCEL
C
/Enter/Setup/Return
VCR/DVD/TV
NOTE: To make the SETUP screen disappear, press SETUP
MENU (or RETURN).
If the DVD/VCR does not operate
properly: Static electricity, etc., may
affect the player's operation.Disconnect
the AC power cord once, then connect
it again.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback procedure
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
POWER
TV
VCR
DVD
Press OPEN/CLOSE.
1
The disc tray will open.
Place a disc onto the tray.
2
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
Hold the disc, position it with the
ZERO RETURN
printed label side up, align it with
the guides, and place it in its
proper position.
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
Press PLAY or OPEN/CLOSE.
3
POWER
The disc tray closes automati-
cally.
INPUT
On the screen,
changes to
“Reading” and then playback will
commence.
TV VOL
TIMER
TV/VCR
0
• A menu screen may appear on
the TV screen, if the disc has
a menu feature. In this case,
PLAY
Reading
STOP
C
press
,
,
,
or
ENTER to operate a menu
feature.
SKIP
SKIP
/INDEX
/INDEX
Press STOP to end playback.
• The DVD/VCR memorizes the stopped point, depending on
the disc. “ ” appears on the screen for approx. 4 seconds.
ENTER/
SELECT
4
5
SET
SET
SET UP
MENU
CANCEL
“
” keep blinking in the display until the playback is stopped
C
completely. Press PLAY to resume playback (from the scene
point).
• If you press STOP again(“ ” appears on the screen) or unload
the disc, the DVD/VCR will clear the stopped point.
Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and DVD/VCR turns off.
VCR/DVD/TV
Note:
•
If a non-compatible disc is loaded, "Incorrect Disc", "Region Code Error" or "Parental Error" will appear on the TV
screen according to the type of loaded disc. In this case, check your disc again (See pages 35 and 46).
Some discs may take a minute or so to start playback.
A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you
tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate
a problem with the DVD/VCR.
•
•
•
•
When you set a single-faced disc label downwards (ie. the wrong way up) and press PLAY or OPEN/CLOSE,
"Reading" will appear and remain on the screen for approx. 40 seconds and then it will change to "No Disc".
Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays
DVDs according to the disc contents the software producers designed, some playback features may not be
available. Also refer to the instructions supplied with the DVDs.
•
When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoid
possible damage to the audio system, the consumer should take proper precautions when the analog stereo
outputs of the DVD/VCR are connected to an amplification system.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Special playback
Note: There may be a slight delay be-
tween pressing the button and the
function activation.
Fast Forward Playback
Press FF during normal playback.
EachpressofFF willincreasethespeedofthesearchx2, x4, x8, x20.
(in case of Audio-CD: x6 and x16 are available)
• To resume normal playback, press PLAY.
POWER
TV
VCR
DVD
Review Playback
Press REW during normal playback.
Each press of REW will increase the speed of the search x2, x4, x8,
x20. (in case of Audio-CD: x6 and x16 are available)
• To resume normal playback, press PLAY.
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
Still Playback
SEARCH
MODE
SUB TITLE
SP/EP
Press PAUSE during normal
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
playback.
TV
POWER
To resume normal playback, press
PLAY.
INPUT
TV VOL
TIMER
TV/VCR
0
PLAY
Frame Advance
Press PAUSE during still playback.
One frame is advanced each time
you press PAUSE.
STOP
C
SKIP
SKIP
/INDEX
/INDEX
To resume normal playback, press
PLAY.
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
C
Slow-motion Playback
Press SLOW during normal playback or still playback.
Each press of SLOW will change the speed of the slow x1/2, x1/4,
x1/6, x1/7.
VCR/DVD/TV
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE.
Note:
The unit is capable of holding a still video
image or On screen display image on your
television screen indefinitely. If you leave
the still video image or On screen display
image displayed on your TV for an ex-
tended period of time, you risk permanent
damage to your television screen.
Projection televisions are very susceptible.
Locating a chapter or track
Press SKIP (
) Forward or SKIP (
) Reverse during play-
back to locate a chapter that you want to watch.
Each time you press the button, a chapter or track is skipped.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Zooming / Locating Desired Scene
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Zooming
POWER
TV
VCR
DVD
This unit will allow you to zoom in on the frame image. You can
then make selections by switching the position of the frame.
Press ZOOM during playback.
The center part of the image will
be zoomed in.
1
1
EachpressofZOOMwillchange
the ZOOM
(x 1.3),
2.0).
1
OPEN/
CLOSE
2 (x 1.5) and
3 (x
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
Press
/
or
/
to view a different part of the frame.
2
3
TV
You may move the frame from the center position to UP, DOWN,
LEFT or RIGHT direction.
POWER
INPUT
In the zoom mode press ZOOM repeatedly to return to a 1:1
view (
Off).
TV VOL
TIMER
TV/VCR
0
PLAY
Locating Desired Scene
Use the title, chapter and time recorded on the disc to
locate the desired point to play back.
STOP
C
SKIP
SKIP
/INDEX
/INDEX
To check the title, chapter and time, press OSD. (see page 52)
ENTER/
SELECT
SET
SET
Press SEARCH MODE during
playback or stop mode.
1
Jump
Time
Title
Chapter
SET UP
MENU
CANCEL
/Enter/0 9/Cancel/Jump
C
VCR/DVD/TV
Press
or
to select the “Time”, “Title” or “Chapter”.
2
3
Press Number keys to change the number.
• If you input a wrong number, press CANCEL.
• Refer to the package supplied with the disc to check the
numbers.
Note:
•
You can use the Pause, Slow, Search
or Skip feature in the zoom mode.
However, you cannot zoom in during
the Search playback.
In case of theVideo-CD playback with
PBC, the SEARCH MODE does not
work.
Press ENTER.
Playback starts.
4
•
• When you change the title, playback starts from Chapter 1 of
the selected title.
• Some discs may not work in the above operation.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat playback
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Title, Chapter, Track Playback
POWER
TV
VCR
DVD
Press PLAY MODE during playback or stop mode.
1
DVD
CD
Repeat
:
Off
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
/Enter/Play Mode
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
Press ENTER once or twice to select “Chapter” or “Title”.
SP/EP
2
3
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
In case of CD, at first press
to select “Repeat” and then press
TV
ENTER once or twice to select “Track” or “All”.
POWER
DVD
CD
INPUT
Repeat
:
Chapter
Play Mode
Repeat
:
:
Off
All
/Enter/Play Mode
TV VOL
/Enter/Play Mode
TIMER
TV/VCR
0
PLAY
Press PLAY MODE again to make the screen disappear.
STOP
C
• Press PLAY to start Repeat playback.
• To resume normal playback, select Repeat Off.
SKIP
SKIP
/INDEX
/INDEX
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
A-B Repeat Playback
C
A-B repeat playback allows you to repeat material between two
selected points.
Press REPEAT A-B during
playback.
The start point is selected.
1
A
VCR/DVD/TV
Note:
•
•
•
•
Some discs may not work with the
repeat operation.
In A-B repeat mode, subtitles near
point A or B may not appear.
During the A-B Repeat Playback the
ANGLE feature will not operate.
You may not be able to set A-B Re-
peat, depending on the scenes of the
DVD.
Press REPEAT A-B again.
The end point is selected.
Playback starts at the point that
you selected. Playback stops at
the end point, returns to Point A
automatically, then starts again.
2
A B
•
A-B repeat does not work with an in-
teractive DVD, MP3-CD andVideo-CD
with PBC.
To resume normal playback press REPEAT A-B again.
“
” appears on the screen.
Off
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Program playback/Random playback (CD)
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Program playback
You can arrange the order of tracks on the disc.
POWER
TV
VCR
DVD
Press PLAY MODE in the stop
mode.
1
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
Press ENTER repeatedly until
the Program table as right
appears.
Play Mode
Repeat
:
:
Program
Off
7
8
9
2
3
ZERO RETURN
SEARCH
MODE
SUB TITLE
1
2
3
4
5
6
10
11
12
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
Quit
Program Playback
/Enter/0 9/Cancel/Play Mode
TV
POWER
INPUT
Example: In case you wish to
program in order of 7, 3, 11:
Play Mode
Repeat
:
:
Program
Off
7
8
9
TV VOL
Enter as 7 , 3
, 11.
1 7
2 3
3 11
Quit
4
5
6
10
11
12
TIMER
TV/VCR
0
If you input a wrong number,
press CANCEL.
PLAY
Program Playback
/Enter/0 9/Cancel/Play Mode
STOP
C
Press
/
or
/
to select
4 “Program Playback” and press
SKIP
SKIP
Program Playback
/INDEX
/INDEX
ENTER. “Program Playback” will
appear on the screen. The
program you selected will begin
to playback in the order set.
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
Toreturntonormalplayback,select
“Play Mode: Off” at step 2 above.
C
Random playback
VCR/DVD/TV
Press PLAY MODE in the stop
mode.
1
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Note:
•
•
•
To cancel program play, select “Quit”
at step 4 and press ENTER.
The program is cancelled when you
openthedisctrayorturnthepoweroff.
Random playback can not be
combined with Repeat playback.
Press
/
toselect“Random”.
2
3
Play Mode
Repeat
:
:
Random
Off
/Enter/Play Mode
Press PLAY.
“Random Play” will appear on the screen and Random Playback
will start.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
MP3 Playback
This player can play back the MP3-data
which has been recorded on CD-R or CD-
RW. To produce the MP3-data, you need a
Windows-PCwithCD-ROMdriveandaMP3-
encoding Software (not supplied).
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/
DVD. Then press DVD to select the DVD mode. (The DVD
indicator will light)
The Apple-HFS-System can not be played.
Press OPEN/CLOSE.
1
The disc tray will open.
Place a disc onto the tray.
MP3 CD Information
Limitations on MP3 CD playback
• MP3 CD is the disc that is standardized by
ISO9660, its file name must include 3-digits
extension letters, “mp3”.
Press PLAY or OPEN/CLOSE.
The disc tray closes automatically.
On the TV-screen, “Reading” and
then reading file number will
appear.Reading will take as much
time as the number of file.
Reading
MP3 15
2
• The directory and file names of the MP3
CD must be correspond to the ISO
standardized files.
• This unit can read 200 files per disc. If
one directory has more than 200 files, it
reads up to 200 files, the remaining files will
be omitted.
A MP3 menu screen will appear
on the TV screen.
Jazz
• As for multi-session disc, only the first
session can be played.
3
Track 1/12
01:28
Japan
1
Pops
1
2
3
4
Japan
Bay Bridge
6
7
8
9
BLUE EYES
Blurry Eyes
Press
folder.
/
or ENTER to select
• If the CD has both audio tracks and MP3
files, only audio tracks are played.
• It may take more than one minute for this
unit to read MP3 files depending on its
structure.
CLOSE MY EYES
DIVE TO BLUE
flower
Lies and Truth-
5
Honey
10 winter fall
/0-9/Enter/Play Mode
• Music recorded by “Joliet Recording
Specification” can be played back, the file
name is displayed (within 17 letters) on the
screen Long file names will be condensed.
• The music files recorded by “Hierarchical
File System” (HFS) cannot be played.
Press
/
or
/
or Number keys to select the desired
4
track, then press ENTER. Track is selected and play
commences.
• In case the folder includes more than 11 tracks, press
or
to display next track list.
Jazz
Jazz
Track 1/12
01:28
Japan
Track 1/12 01:28
Pops
Japan
1
Pops
1
Limitations on display
1
2
3
4
Japan
Bay Bridge
6
7
8
9
BLUE EYES
Blurry Eyes
11 Mother
12 Hold Your Last
• The maximum number for display is 17
letters. Available letters for display are the
following: capital or small alphabets of A
through Z, numbers of 0 through 9, and _
(under score).
CLOSE MY EYES
DIVE TO BLUE
flower
Lies and Truth
5
Honey
10 winter fall
/0-9/Enter/Play Mode
/0-9/Enter/Play Mode
• Other letters than those above are replaced
in hyphen.
Press STOP to end playback.
5
6
• The unit records the stopped point. “ ” appears on the
screen. Press PLAY to resume playback (from the scene
point).
• If you press STOP again or unload the disc, the unit will
clear the stopped point.
Notes on MP3 files
To play back MP3 CD in the recorded order,
1. Use MP3 software that records data
alphabetically or numerically.
2. Name each file including two-digit or three-
digit number (e.g. "01" "02" or "001" "002").
3. Refrain from making too many sub-folders.
Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and DVD/VCR turns off.
CAUTION:
• Some MP3 CDs can not be played back
depending on the recording conditions.
• The CD-R/RW that has no music data or
non-MP3 files can not be played back.
Note:
•
During MP3-Playback, you can not use SEARCH, A-B
Repeat functions.
•
You can use Repeat(Track or All) and Random functions for
MP3 CD Playback.(See page 40 and 41)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Marking Desired Scenes
The unit stores the points that you
want to watch again up to 3 points.
You can resume playback from
each scene.
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Marking the Scenes
POWER
TV
VCR
DVD
Press MARKER during
playback.
1
Marker
Marker
Marker
1
2
3
/Enter/Cancel/Marker
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
Select the blank Marker using
ZERO RETURN
2
3
Marker
Marker
Marker
1
2
3
00 27 54
/
.
SEARCH
MODE
SUB TITLE
ThenpressENTERatthedesired
scene.
SP/EP
PLAY
/Enter/Cancel/Marker
REPEAT
A-B
ZOOM
TITLE
MODE
TV
• Repeat this procedure to set
the other 2 scenes.
POWER
INPUT
Press MARKER to remove this display.
TV VOL
TIMER
TV/VCR
0
PLAY
Returning to the Scenes
PressMARKERduringplayback
or stop mode.
1
Marker
Marker
Marker
1
2
3
00 27 54
01
02
STOP
C
16 25
08 31
/Enter/Cancel/Marker
SKIP
SKIP
/INDEX
/INDEX
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
Press
1-3.
/
to select the Marker
2
3
Marker
Marker
Marker
1
2
3
00 27 54
01
02
C
16 25
08 31
/Enter/Cancel/Marker
VCR/DVD/TV
Press ENTER.
Playback starts from the marked scene.
Note:
•
•
•
•
Some discs may not work with the
marking operation.
The marking is canceled when you
open the disc tray or turn the power off.
Some subtitles recorded around the
marker may fail to appear.
WhiletheMARKERscreenisdisplayed,
ifyoudoaspecialplaybackastheFast
Forward/Review Playback
or SKIP, the MARKER screen will
disappear. Press MARKER again as
soon as you find the desired scene.
To Cancel the Mark
Press MARKER.
1
2
3
Press
/
to select the Marker 1-3.
Press CANCEL.
To remove this display, press MARKER.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing soundtrack language / Subtitles
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
OPEN/
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
CLOSE
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
Changing soundtrack language
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
You can select the language when you play a multilingual disc.
TV
POWER
Press A.MONITOR during
playback.
Thecurrentsoundtracklanguage
will appear.
1
2/8 Fra DolbyDigital
INPUT
TV VOL
TIMER
TV/VCR
0
PLAY
Press A.MONITOR repeatedly
until the desired language is
selected.
The on-screen display will
disappear after a few seconds.
2
1/8 Eng DolbyDigital
STOP
C
SKIP
SKIP
/INDEX
/INDEX
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
In case of VIDEO CD playback
C
AudiotypechangesasfollowseachtimeyoupressA.MONITOR.
LR
L
R
VCR/DVD/TV
Turning the Subtitles On and Off
When playing back a disc recorded with subtitles, you can turn
the subtitles on or off.
Note:
Press SUB TITLE during playback
until “OFF” appears.
•
If the desired language is not heard
after pressing the button several times,
the language is not recorded on the disc.
Changing soundtrack or subtitle
language is cancelled when you open
the disc tray or turn the power off. The
initial default language or available
language will be heard and seen if the
disc is played back again.
Off
•
Changing the subtitle language
•
•
Depending on the DVD you may be
unable to turn on, turn off, or change the
subtitles, even if they are recorded on
the disc. While playing the DVD, the
subtitle may change while opening or
closing the disc tray, or while changing
the title.
In some cases, the subtitle language is
not changed to the selected one
immediately.
You can select the language when playing back a disc
recorded with multi-lingual subtitles.
Press SUB TITLE repeatedly during
playbackuntilyourdesiredlanguage
appears.
The on-screen display will disappear
after a few seconds.
1/32 Eng
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing angles / Title selection / DVD menu
Preparation:
• Turn ON the TV and set it to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Changing Angles
POWER
TV
VCR
DVD
When playing back a disc recorded with multi-angle facility, you
can change the angle that you are viewing the scene from.
Press ANGLE during playback.
The current angle will appear.
1
1/9
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
Press ANGLE repeatedly until the desired angle is selected.
2
TV
POWER
INPUT
Title Selection
Two or more titles are recorded on some discs. If the title menu
TV VOL
TIMER
TV/VCR
0
is recorded on the disc, you can select the desired title.
PLAY
Press TITLE during playback.
1
Title menu appears on the screen.
STOP
C
• Press TITLE again to resume playback at the scene when you
pressed TITLE.
SKIP
SKIP
/INDEX
/INDEX
Press
/
or
/
to select the desired title.
2
3
ENTER/
SELECT
SET
SET
Press ENTER or PLAY.
The playback of the selected title will start.
SET UP
MENU
CANCEL
C
DVD Menu
Some DVDs allow you to select the disc contents using the
menu.
VCR/DVD/TV
When you play back these DVDs, you can select the subtitle
language and sound-track language,etc. using the DVD menu.
Press DVD MENU during playback.
1
Note:
The DVD menu appears on the screen.
Depending on the DVD, you may not
be able to change the angles even if
multi-angles are recorded on the disc,
or you may be unable to select the title,
and a "title menu" may simply be called
a "menu" or "title" in the instructions
supplied with the disc.
• Press DVD MENU again to resume playback at
the scene when you pressed DVD MENU.
Press
/
or
/
to select the desired item.
2
3
Press ENTER.
The menu continues to another screen. Repeat steps 2 and 3 to
set the item completely.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental control
Somediscsarespecifiednotsuitable
for children. Such discs can be
prevented from play back with the
unit.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Parental control setting
POWER
TV
VCR
Language Picture
Password
Parental
Other
DVD
Press SETUP MENU in the stop mode.
Press or to select “Parental”.
Then press ENTER.
1
2
3
Parental
8
0
9/Cancel
/Enter/Setup/Return
Press
or
to select “Parental 8”,
Language Picture
Password
Parental
Other
OPEN/
CLOSE
then press ENTER until the level you
desire appears (e.g.: 1).
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
Parental
1
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
/Enter/Setup/Return
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
POWER
Press
once to select “Password
”.
Language Picture
Parental
Other
Then press Number keys to input a 4-
digit password (e.g.: 1234).
INPUT
Password
Parental
1234
1
• If you input a wrong number, press
CANCEL.
• Be sure to remember this number!
TV VOL
0
9/Cancel
/Enter/Setup/Return
TIMER
TV/VCR
0
PLAY
Level 1: DVD software for adults cannot be played back.
Level 8: All DVD software can be played back.
STOP
C
Select from level 1 to level 8.
On a scale of 1-8, "1" is the most restrictive.
SKIP
SKIP
/INDEX
/INDEX
Language Picture
Parental
Other
Press ENTER.
4
5
1234
change to
.
Password
ENTER/
SELECT
SET
SET
Parental
1
SET UP
MENU
CANCEL
0
9/Cancel
/Enter/Setup/Return
C
To make SETUP screen disappear, press SETUP MENU.
Note:
To unlock the Parental Control Setting
• If each setup (page 46~52) has been
completed, the unit can always be
worked under the same conditions
(especially with DVD discs).
Each setup will be retained in the
memory if you turn the power off.
• Depending on the discs, the unit can-
not limit playback.
• Some discs may not be encoded with
specific rating level information though
its disc jacket says "adult". For those
discs, the age restriction will not work.
• Do not forget the password. If you forget
the password, contact customer service.
Cancel the password so as to set the Parental level freely again,
Language Picture
Parental
Other
Select “Password
and press Number keys to input your
4-digit password.
” (step 1)
1
2
Password
Parental
1234
1
Then press ENTER.
0
9/Cancel
/Enter/Setup/Return
If the input password was right,
will appear.
You can move to “Parental 1”(e.g.) to
input the desired level or to cancel
parental control.
Language Picture
Password
Parental
Other
Parental
1
0
9/Cancel
/Enter/Setup/Return
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Temporary disabling of rating level by DVD disc
Depending on the DVD disc, the
Preparation:
disc may try to temporarily cancel
the rating level that you have set.
It is up to you to decide whether to
cancel the rating level or not.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
LoadaDVDdiscandpressPLAY
1
or OPEN/CLOSE (see page 37).
POWER
TV
VCR
DVD
If the DVD disc has been designed to temporarily cancel the
2
Rating level, the screen which follows the “Reading” screen will
change, depending on which disc is played. If you select “YES”
with ENTER key, “Your disc exceeds the parental control level
1.”(e.g.) screen will then appear.
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
Reading
Your disc exceeds
the parental control level 1.
TV
POWER
Parental Control Level
Cancel Picture
INPUT
/Enter/Return
TV VOL
TIMER
TV/VCR
0
If you wish to cancel the set rating level temporarily, select
PLAY
3
“Parental Control Level” with
or
, then press ENTER. If
the 4-digits password at step 3 on page 46 has been set, the
password entering screen will appear as shown in step 4 below.
Alternatively, if the password has not been set, playback will
commence. If you don’t know (or have forgotten) the password,
select “Cancel Picture”.
STOP
C
SKIP
SKIP
/INDEX
/INDEX
The setting screen will disappear. Press OPEN/CLOSE to
remove the disc.
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
Enter the password with
Number buttons (0-9).
Then press ENTER.
C
4
5
Please enter the
digit password
4
Enter/0 9/Cancel/Return
If you interrupt the entering,
press RETURN.
VCR/DVD/TV
Playback will commence if the entered password was correct.
Note:
This temporary cancellation of rating
level will be kept until the disc is ejected.
When the disc is ejected, the original
rating level will be set again
automatically.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menu language
You can select the language of the
Preparation:
disc menu messages of DVDs.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Press SETUP MENU in the stop
mode.
Language Picture
Parental
Other
1
2
3
POWER
TV
VCR
DVD
Press
or
to select
“Language”.
/Enter/Setup/Return
Press ENTER.
Then press
“Menu”.
Language Picture
Parental
Other
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
or
to select
ZERO RETURN
Menu
Subtitle
Audio
English
English
English
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
/Enter/Setup/Return
POWER
INPUT
Press ENTER.
Language Picture
Parental
Other
Press
or
to select your
Menu
English
English
Francais
Espanol
Other
TV VOL
Subtitle
Audio
English
English
desired language, then press
ENTER.
TIMER
TV/VCR
0
PLAY
0
9/Cancel
/Enter/Setup/Return
STOP
C
English, Francais, Espanol
The selected language is the first-priority Menu language.
SKIP
SKIP
/INDEX
/INDEX
OTHER: Other language can be selected (See the Language
ENTER/
SELECT
SET
SET
Code List on page 53).
SET UP
MENU
CANCEL
To make SETUP screen disappear, press SETUP MENU.
C
4
VCR/DVD/TV
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting subtitle language
The same subtitle language can
always be selected even if you replace
the disc or turn the power off.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Press SETUP MENU in the stop
mode.
Language Picture
Parental
Other
Other
Other
1
2
3
POWER
TV
VCR
DVD
Press
or
to select
“Language”
/Enter/Setup/Return
OPEN/
CLOSE
Press ENTER.
Language Picture
Parental
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
Then press
“Subtitle”.
or
to select
Menu
Subtitle
Audio
English
English
English
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
POWER
/Enter/Setup/Return
INPUT
Press ENTER.
Language Picture
Parental
Press
or
to select your
TV VOL
Menu
Subtitle
Audio
English
English
English
English
Francais
Espanol
Other
TIMER
desired language, then press
ENTER.
TV/VCR
0
PLAY
0
9/Cancel
Automatic
Off
/Enter/Setup/Return
STOP
C
English, Francais, Espanol
SKIP
SKIP
/INDEX
/INDEX
The subtitle is displayed with the selected language if it is
recorded on the disc.
ENTER/
SELECT
SET
SET
OTHER:
SET UP
MENU
CANCEL
If you want to select another language, enter the language code
(see the language code list on page 53).
C
AUTOMATIC:
• The unit will automatically select the same language in the
AUDIO setting.
• When the unit selects the same language as the AUDIO, the
subtitles will not appear during playback.
VCR/DVD/TV
• When you do not use the same language as the AUDIO, the
subtitles will appear during playback.
Off:
Note:
Subtitles do not appear.
If the selected language is not recorded
on the disc, the first-priority language is
selected.
To make SETUP screen disappear, press SETUP MENU.
4
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting audio soundtrack language / Setting surround sound
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Setting audio soundtrack
language
Thesameaudiosoundtracklanguage
can always be selected by your unit
even if you replace the disc or turn
Press SETUP MENU in the stop
mode.
Press or toselect“Language”
Language Picture
Parental
Other
Other
Other
the power off.
1
2
3
/Enter/Setup/Return
Press ENTER.
Then press
“Audio”.
Language Picture
Parental
or
to select
OPEN/
CLOSE
Menu
Subtitle
Audio
English
English
English
DVD MENU
DISPLAY
MARKER
RETURN
C.RESET
ANGLE
A.TRK
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
/Enter/Setup/Return
TV
Press ENTER.
Press
desired Audio Language, then
POWER
Language Picture
Parental
or
to select your
Menu
Subtitle
Audio
English
English
English
English
Francais
Espanol
Other
INPUT
press ENTER.
0
9/Cancel
Original
TV VOL
/Enter/Setup/Return
TIMER
TV/VCR
0
PLAY
• English, Francais, Espanol:
The language you have selected will play if it is recorded on
the disc.
STOP
C
• OTHER: If you want to select another language,
enter the language code (See the Language Code List on page
53).
SKIP
SKIP
/INDEX
/INDEX
• ORIGINAL: The unit will select the first priority language of
each disc.
ENTER/
SELECT
SET
SET
SET UP
MENU
To make SETUP screen disappear, press SETUP MENU.
CANCEL
4
C
Setting surround sound
This DVD/VCR equipped with a “SPATIALIZER 3-D STEREO”
as the SURROUND option in the VCR menu. It can produce the
effect of being in a cinema or a concert hall.
VCR/DVD/TV
Since the SURROUND option exists in the VCR menu, the setting
is possible only during a disc-playback or in the VCR mode.
Note:
During disc-playback press SETUP MENU.
•
If the selected language is not
recorded on the disc, the original
language will be heard.
1
2
Press
or
to select
MENU
TIMER REC SET
AUTO REPEAT
SAP
SURROUND
CH SET UP
SYSTEM SET UP
SURROUND.
Then press ENTER to select [ON]
or [OFF].
•
The “SPATIALIZER 3-D STEREO” is
effective only for the sound of disc.
ON OFF
ON OFF
ON OFF
To cancel Surround mode:
〈+/-/ENTER/MENU〉
Follow the right steps 1~2, then press
ENTER to select the OFF position.
Press SETUP MENU to return to theTV.
Press SETUP MENU until the menu screen is cleared.
3
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the aspect ratio of TV screen
You can select the aspect ratio for
Preparation:
your TV.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Press SETUP MENU in the stop
mode.
Language Picture
Parental
Other
Other
Other
1
2
3
POWER
TV
VCR
DVD
Press or
toselect“Picture”.
/Enter/Setup/Return
OPEN/
CLOSE
Press ENTER, then press
or
Language Picture
Parental
DVD MENU
MARKER
A.TRK
RETURN
C.RESET
ANGLE
to select “Tv Screen”.
DISPLAY
ZERO RETURN
Tv Screen
Display
4:3
On
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
TV
POWER
/Enter/Setup/Return
INPUT
Press ENTER.
Language Picture
Parental
Press
or
to select your
TV VOL
Tv Screen
Display
4:3
On
4:3
4:3
16:9
desired screen type, then press
ENTER.
TIMER
TV/VCR
0
PLAY
/Enter/Setup/Return
STOP
C
You have the following screen sizes to choose from:
SKIP
SKIP
/INDEX
/INDEX
4:3
Select this mode when connecting to a conventional TV. When
playing back a wide screen-DVD disc, it displays the wide picture
with black bands at the top and bottom of screen.
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
C
4:3
PAN SCAN
It displays the wide picture on the whole screen with left and
right edges automatically cut off.
16:9
WIDE SCREEN
VCR/DVD/TV
Select this mode when connecting to a wide-screen TV.
A wide screen picture is displayed full size.
To make SETUP screen disappear, press SETUP MENU.
Note:
4
If the DVD disc is not formatted in the pan
& scan style, it displays 4:3 style.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting on Screen display / Status display of Disc
On screen display can be switched on
Preparation:
or off when you press the buttons.
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Then press DVD to select the DVD mode. (The DVD indicator will light)
Press SETUP MENU in the stop
mode.
Language Picture
Parental
Other
Other
Other
1
POWER
TV
VCR
DVD
Press
or
to select “Picture”
/Enter/Setup/Return
Press ENTER, then press
or
Language Picture
Parental
2 to select “Display”.
Tv Screen
Display
4:3
On
OPEN/
CLOSE
DVD MENU
DISPLAY
MARKER
A.TRK
RETURN
C.RESET
ANGLE
ZERO RETURN
SEARCH
MODE
SUB TITLE
SP/EP
PLAY
REPEAT
A-B
ZOOM
TITLE
MODE
/Enter/Setup/Return
TV
POWER
Language Picture
Parental
Press ENTER to select “On” or
“Off”.
3
Tv Screen
Display
4:3
Off
INPUT
TV VOL
TIMER
TV/VCR
0
/Enter/Setup/Return
PLAY
On: On screen displays appears when you press the any
buttons (factory setting).
STOP
C
Off: On screen displays do not appear when you press any
buttons except SETUP MENU, SEARCH MODE, PLAY
MODE, MARKER and OSD.
SKIP
SKIP
/INDEX
/INDEX
To make SETUP screen disappear, press SETUP MENU.
4
ENTER/
SELECT
SET
SET
SET UP
MENU
CANCEL
C
Status display of Disc
Each Press of OSD, the status display of the disc will appear on the
screen and change as follows.
DVD
00:34:56 01:12:33
00:34:56 01:12:33
Title
1/99 Chapter 1/999
1/9
VCR/DVD/TV
1/8 Eng DolbyDigital
1/32 Eng
VIDEO
CD
00:09
34:56
04:35
71:33
PBC
00:12
34:56
04:32
Track —/—
Track 11/99
AUDIO
CD
71:33
To make status display disappear, press OSD again.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
Enter the appropriate code number for the initial settings "Audio", "Subtitle" and/or "Menu" (see pages 48-
50).
Language Name Code Language Name Code Language Name Code Language Name Code
Abkhazian
Afar
1112 Fiji
1620 Lingala
1619 Lithuanian
1628 Macedonian
1635 Malagasy
1722 Malay
2224 Singhalese 2919
1111 Finnish
1116 French
2927 Frisian
1123 Galician
1128 Georgian
1835 German
1129 Greek
1135 Greenlandic
1136 Guarani
1211 Gujarati
1531 Hausa
2230 Slovak
2321 Slovenian
2317 Somali
2329 Spanish
2921
2922
2925
1529
Afrikaans
Albanian
Amharic
Arabic
2111 Malayalam
1415 Maltese
1522 Maori
2322 Sundanese 2931
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
2330 Swahili
2319 Swedish
2328 Tagalog
2325 Tajik
2933
2932
3022
3017
3011
3030
3015
3018
1225
3019
3025
3028
3021
3033
3121
3128
3136
2122 Marathi
1724 Moldavian
1731 Mongolian
1811 Nauru
2324 Tamil
Basque
2411 Tatar
Bengali; Bangla 1224 Hebrew
1933 Nepali
2415 Telugu
2425 Thai
Bhutani
Bihari
1436 Hindi
1819 Norwegian
1831 Oriya
1218 Hungarian
1228 Icelandic
1217 Indonesian
2335 Interlingua
1215 Irish
2528 Tibetan
2611 Tigrinya
2629 Tonga
1611 Turkish
2622 Turkmen
2630 Twi
Breton
1929 Panjabi
1924 Pashto, Pushto
1911 Persian
1711 Polish
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
2123 Italian
1930 Portuguese
2011 Quechua
1311 Japanese
3618 Javanese
1325 Kannada
1828 Kashmiri
1329 Kazakh
1411 Kirghiz
2422 Korean
1524 Kurdish
1525 Laothian
1530 Latin
2731 Ukrainian
2033 Rhaeto-Romance 2823 Urdu
2124 Romanian
2129 Russian
2121 Samoan
2135 Sanskrit
2125 Scots Gaelic
2131 Serbian
2825 Uzbek
2831 Vietnamese 3219
2923 Volapük
2911 Welsh
1714 Wolof
2928 Xhosa
2918 Yiddish
2924 Yoruba
2914 Zulu
3225
1335
3325
3418
2019
3525
3631
Danish
Dutch
English
Esperanto
Estonian
Faroese
2225 Serbo-Croatian
2211 Shona
1625 Latvian, Lettish 2232 Sindhi
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and troubleshooting
Use the following check list for troubleshooting when you have problems with your unit. Consult your local
dealer or service outlet if problems persist.
Be sure all connections are properly made when using with other units.
SYMPTOMS
DVD/VCR
POSSIBLE SOLUTIONS
PAGE
•Make sure the power cord is plugged in.
•Try another AC outlet.
5
–
•Power is off, check fuse or circuit breaker.
•Unplug unit, then plug it back in.
–
5
DVD/VCR does not operate.
•Select the DVD or VCR mode before operating.
•Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
18,36
18,36
•
Antenna connection is not correct or antenna cable is disconnected.
12~15
18
• The video channel is not in the correct position or the TV is not
set to the video channel 3 or 4.
• Check the unit is connected correctly.
• The video input selector of the TV is not set to VIDEO. Set to
VIDEO (or equivalent).
12~17
–
No picture.
No sound.
• Channel is set to the external mode.
–
• Check the unit is connected correctly.
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
12~17
–
26,38
• Aim at the remote control at the remote sensor.
• Operate within Approx. 5 Meters or reduce the light in the room.
• Clear the path of the beam.
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
• Check the frequency code is set correctly.
The remote control does not
function.
11
The DVD-keys on the RCU of the
other JVC RECEIVER/TV is not
effective.
•This is not a defect. Since this unit is combined type of DVD
and VCR, the remote code of DVD is individual.
10
14,15
23
•Check all CATV connections.
•Station or CATV system problems, try another station.
No CATV reception
•During the Auto Clock operation, a video signal can be put out.
Please set the clock with Manual clock setting or wait until the
Auto Clock operation completed.
No POWER but a picture appears
on the TV screen.
VCR
•The erase prevention tab of the video cassette is broken off.
•The unit is in the external input mode.
TV recording does not work.
24,28
• The time is not set correctly.
• The recording start/end time is not set correctly.
• The TIMER has not been pressed ( is not lit).
21,23
31
31
Timer recording does not work.
• Tracking adjustment beyond range of automatic tracking circuit.
Try Manual tracking adjustment.
• Video heads are dirty.
26
Noise bars on screen.
55
–
• The tape is worn or damaged.
DVD
Display is not shown in your
language.
•Select proper language in the menu options.
36
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play DVD-ROMs, etc.
37
35
35
Playback doesn’t start.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and troubleshooting / Video head cleaning
SYMPTOMS
POSSIBLE SOLUTIONS
PAGE
Stopping playback, search, slow-
motion play, repeat play, or program
play, etc. cannot be performed.
–
• Some discs may not do some of the functions.
No 4:3 (16:9) picture
No on-screen display
No surround sound
• The setup does not match your TV.
• Select Display On.
51
52
17
• The setup does not match your stereo system.
The unit or remote operation key
is not functioning.
• Turn off the unit and unplug the AC power cord for several
minutes, then replug it.
–
Playback does not start when the
title is selected.
• Check the Parental setup.
46
Audio soundtrack and/or subtitle
language is not changed when you
play back a DVD.
49,50
• Multilingual language is not recorded on the DVD disc.
• Some discs have no subtitles.
• Subtitles are cleared. Press SUB TITLE.
49
No subtitle
Angle cannot be changed.
appears on the screen.
• Multi-angles are not recorded on the DVD disc.
• The function is prohibited with the unit or the disc.
45
–
Video head cleaning
Video head clogging
The video heads are the means by which the DVD/VCR reads
the picture from the tape during playback. In the unlikely event
that the heads become dirty enough to be clogged, no picture
will be played back. This can easily be determined if, during
playback of a known good tape, there is good sound, but no
picture (picture is extremely snowy). If this is the case, have
the DVD/VCR checked by qualified service personnel.
Good Picture
Snowy Picture
NOTES: DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE
•
REAR COVER.
Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
•
•
Notes
Auto Clock Setting
Notes for customers regarding the clock feature of the your DVD/VCR.
The XDS signals are carried only by certain broadcast television stations (for example, the signal is carried by
most Public Broadcasting Service stations).You must be able to receive a station carrying the XDS signal to
use the Auto Clock Setting to set your DVD/VCR’s internal clock. If you live in an area that does not broadcast
XDS signals, you must set the clock manually. Please see page 23 for instructions on how to manually set your
DVD/VCR’s clock.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
GENERAL
Power supply:
Power consumption:
Weight:
AC 110-220V, 50/60Hz
Operation: 22W at 220V 60Hz, Stand by: 4W at 220V 60Hz
9.9lbs (4.5 kg)
Dimensions:
Width : 16-15/16 inches (430 mm)
Height: 3-7/8 inches (99 mm)
Depth : 12-1/4 inches (311 mm)
Inputs/Outputs:
Video:
In: 1Vp-p/75 ohm, Out: 1Vp-p/75 ohm
In: -8 dBm/50K ohm, Out: -8 dBm/1K ohm
UHF/VHF IN/OUT: 75 ohm coaxial
Audio:
Antenna:
Hi-Fi Frequency Response: 20Hz to 20,000Hz
Hi-Fi Dynamic Range:
VCR section
Video Head:
Audio Track:
Tuner:
More than 90dB
4 Rotary Heads
Hi-Fi Sound - 2 Tracks / MONO Sound - 1 Track
181 Channel Freq. Synthesized
VHF
UHF
2-13
14-69
CATV 14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
RF Channel Output:
F.FWD/REW Time:
DVD section
Channel 3 or 4, Switchable
Approx. 1minute and 48 seconds (with T-120 Cassette Tape) (at +25°C)
Signal system:
NTSC
Applicable disc:
Audio characteristics:
Frequency response:
S/N Ratio:
DVD (12cm, 8cm), CD (12cm, 8cm)
DVD: 4Hz - 22KHz
CD: 4Hz - 20KHz
90dB
Harmonic distortion:
Wow and flutter:
Dynamic range:
Output:
0.01%
Below Measurable Level
90dB
Video : (RCA) 1 Vp-p/75ohm
Audio : (RCA) -8 dBm/1Kohm
Digital Audio : 0.5Vp-p 75 ohm
CD : Wavelength: 775 - 805 nm, Maximum output power: 0.5 mW
DVD : Wavelength: 640 - 660 nm, Maximum output power: 1.0 mW
Remote control x 1
Pickup:
ACCESSORIES:
Batteries (2 x AA)
75 ohm Coaxial Cable x 1
AUDIO/VIDEO Cable x 1
Conversion plug x 1
VICTOR COMPANY OF JAPAN, LIMITED
2A30901A U
02/03
Printed in Thailand
Download from Www.Somanuals.com. All Manuals Search And Download.
|