DVD VIDEO RECORDER
DR-M100S
CH+
RAM/RW
STANDBY/ON
PUSH-OPEN
CH
-
i
For Customer Use:
Enter below the Model No. and
Serial No. which are located on the
rear of cabinet. Retain this
information for future reference.
INSTRUCTIONS
Model No.
Serial No.
EN
LPT1013-001B
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
EN
3
ANTENNA INSTALLATION INSTRUCTIONS
IMPORTANT PRODUCT SAFETY
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded so as
to provide some protection against voltage surges and built-up
static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, size of grounding
connectors, location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
Electrical energy can perform many useful functions. But improper
use can result in potential electrical shock or fire hazards. This
product has been engineered and manufactured to assure your
personal safety. In order not to defeat the built-in safeguards,
observe the following basic rules for its installation, use and
servicing.
ATTENTION:
2. Lightning
Follow and obey all warnings and instructions marked on your
product and its operating instructions. For your safety, please read
all the safety and operating instructions before you operate this
product and keep this booklet for future reference.
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the product due to
lightning and power-line surges.
INSTALLATION
1. Grounding or Polarization
(A)Your product may be equipped with a polarized alternating-
current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a
safety feature.
3. Power Lines
An outside antenna system should not be located in the vicinity
of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be
taken to keep from touching such power lines or circuits as
contact with them might be fatal.
If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
(B)Your product may be equipped with a 3-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.
2. Power Sources
Operate your product only from the type of power source
indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your product dealer or local
power company. If your product is intended to operate from
battery power, or other sources, refer to the operating
instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
5. Ventilation
Slots and openings in the cabinet are provided for ventilation.
To ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered.
● Do not block the openings by placing the product on a bed,
sofa, rug or other similar surface.
● Do not place the product in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
4
EN
USE
SERVICING
1. Servicing
1. Accessories
To avoid personal injury:
If your product is not operating correctly or exhibits a marked
change in performance and you are unable to restore normal
operation by following the detailed procedure in its operating
instructions, do not attempt to service it yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
● Do not place this product on an unstable cart, stand, tripod,
bracket, or table. It may fall, causing serious injury to a child or
adult, and serious damage to the product.
● Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the product.
● Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s instructions for
any mounting of the product.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.
● Do not try to roll a cart with small casters across thresholds or
deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
3. Water and Moisture
Do not use this product near
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in
performance^this indicates a need for service.
water^for example, near a bath tub,
wash bowl, kitchen sink or laundry tub,
in a wet basement, or near a swimming pool and the like.
3. Replacement Parts
4. Object and Liquid Entry
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or which have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short-
out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
5. Attachments
4. Safety Check
Do not use attachments not recommended by the manufacturer
of this product as they may cause hazards.
the service technician to perform safety checks to determine
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
HOW TO USE THIS INSTRUCTION MANUAL
Contents on page 6. Use this when searching for information on
a specific procedure or feature.
● The Index on pages 12 - 14 illustrates the controls and
connections on the front and rear panel, the front display panel
and the remote control.
7. Heat
The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
● The list of terms on page 70 lists frequently-used terms, and the
number of the page on which they are used or explained in the
manual.
● The A mark signals a reference to another page for instructions
or related information.
of each major section.
BEFORE YOU INSTALL YOUR NEW UNIT . . .
. . . please read the sections/literature listed below.
● “SAFETY FIRST” (A pg. 2)
● AIMPORTANT PRODUCT SAFETY INSTRUCTIONSB (A pg. 3
- 5)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
EN
5
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
Declaration of Conformity
Model Number:DR-M100SU
Trade Name:JVC
Responsible Party:JVC Americas Corp.
Address:1700 Valley Road Wayne, N.J. 07470
Telephone Number:973-317-5000
Failure to heed the following precautions may result in
damage to the unit, remote control or disc.
1. DO NOT place the unit ^
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
^ in an environment prone to extreme temperatures or
humidity.
^ in direct sunlight.
^ in a dusty environment.
^ in an environment where strong magnetic fields are
generated.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
^ on a surface that is unstable or subject to vibration.
2. DO NOT block the unit’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the unit or remote control.
4. DO NOT place anything which might spill on top of the unit
or remote control.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with
water. Also DO NOT place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases, potted
plants, cups, etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
8. AVOID violent shocks to the unit during transport.
MOISTURE CONDENSATION
i
Moisture in the air will condense on the unit when you move it from
a cold place to a warm place, or under extremely humid
conditions^just as water droplets form on the surface of a glass
filled with cold liquid. In conditions where condensation may occur,
disconnect the unit’s power plug from the wall and keep it
disconnected for a few hours to let the moisture dry, then turn on
the unit.
● Manufactured under licence from Dolby Laboratories. ADolbyB
and double-D symbol are trademarks of Dolby Laboratories.
● ADTSB and ADTS DIGITAL OUTB are trademarks of Digital
Theater Systems, Inc.
● VCR Plus+ and PlusCode are registered trademarks of Gemstar
Development Corporation.
The VCR Plus+ system is manufactured under license from
Gemstar Development Corporation.
DISCLAIMER OF LIABILITY:
TM
JVC shall not be liable for any loss relating to the unit’s failure to
properly record, store or playback any content (video, audio or
otherwise) for any reason whatsoever. Any applicable warranties
shall only cover replacement or repair of the effected unit, and
shall not apply to recovery or replacement of lost content.
● DSS is an official trademark of DIRECTV, Inc., a unit of GM
TM
Hughes Electronics. DISH Network is a trademark of Echostar
Communications Corporation.
● This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing users only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
ATTENTION:
8
Using a mobile phone in the vicinity of the unit may cause
picture vibration on the TV screen or change the screen to a
blue back display.
Some TVs or other appliances generate strong magnetic
fields. Do not place such appliances on top of the unit as it
may cause picture disturbance.
If there is a power outage when using the unit, the recorded
data may be erased.
Recorded programmes and data cannot be restored once
the disc is damaged.
8
8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6
EN
SAFETY FIRST
2
EDITING
Digital Audio Dubbing.................................................................. 56
About Discs....................................................................................7
INDEX
INITIAL SETTINGS
BASIC OPERATIONS ON DVD DECK
Basic Playback.............................................................................22
APPENDIX
70
71
72
TIMER RECORDING
LIST OF TERMS
WARRANTY (Only in U.S.A.)
FOR SERVICING (Only in U.S.A.)
Basic Operation Of Original Information ......................................44
Edit Original Information...............................................................46
Basic Operation Of Play List Information .....................................47
Edit Play List Information .............................................................48
Edit Library Information................................................................51
Playback With MP3/JPEG Navigation..........................................52
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
7
DVD-R/RW Discs
It is only possible to use DVD-R discs which conform with DVD-R
standard Version 2.0 or 2.1.
About Discs
It is only possible to use discs which conform with DVD-RW
standard Version 1.1 or 1.2. Available in VR mode and Video
mode.
When a DVD-R/RW disc (Video mode) is finalized (A pg. 64), it
can be played back on a standard DVD player as a DVD VIDEO
disc.
Recordable/Playable Discs
You can use discs with the following logos for recording and
playback.
When a DVD-RW disc (VR mode) is finalized (A pg. 64), it can be
played back on DVD player compatible with the VR mode of
DVD-RW discs.
Before finalizing ^
^ it is possible to record on unrecorded areas of the disc, edit the
disc title and program titles, and delete programs.
● It is impossible to record or edit DVD-R/RW discs recorded on
other devices even if they have not been finalized.
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
program is deleted from a DVD-R disc.
DVD-RAM
DVD-RW
12 cm: 4.7 GB/9.4 GB
8 cm: 1.4 GB/2.8 GB
Ver. 2.0/2x speed
Ver. 2.1/1x – 3x speed
Ver. 2.2/5x speed
12 cm: 4.7 GB
8 cm: 1.4 GB
Ver. 1.1/1x – 2x speed
(Video mode/VR mode)
Ver. 1.2/4x/6x speed
(Video mode/VR mode)
After finalizing ^
After a DVD-R/RW disc (Video mode) has been finalized, it is
possible to play back the recorded programs (video and/or audio)
on a standard DVD video player as a DVD VIDEO disc.
● Edited titles are displayed
CONTENTS MENU
as the “DVD menu” in
video mode.
PREV
DVD-R
81 Sister Princess ED2 14/11 0:55 PR12<HDD MN26
82 GALAXY ANGLE A#04 OP 06/10 9:30 PR12<HDD
83 GALAXY ANGLE A#04 ED 06/10 9:30 PR12<HDD
84 FISHING WORLD OP 22/12 20:00 PR3
85 FISHING WORLD ED 22/12 20:00 PR3
86 RALLY CAR OP 10/04 0:30 PR3
16.11.2002
07.10.2002
07.10.2002
22.12.2002
22.12.2002
04.10.2002
04.10.2002
02.05.2002
02.05.2002
26.09.2002
12 cm: 4.7 GB
8 cm: 1.4 GB
● It is impossible to record,
edit or delete the data
either in video mode or in
VR mode.
● Either in video mode or in
VR mode, although the
disc can be played back
on DVD players from other
Ver. 2.0/1x - 4x/8x speed
(Video mode)
Ver. 2.1/16x speed
(Video mode)
87 RALLY CAR ED 10/04 0:30 PR3
88 Chobits #04 OP 02/05 PR10
89 Chobits #04 ED 02/05 PR10
90 Chobits #25 ED 26/09 PR10 MN32 LPCM
NEXT
● The above table is based on the information as of January 2005.
● Recording and playback may not be performed depending on the
characteristics and condition of the disc used, leading to
unsatisfactory results. Using discs manufactured by JVC is
recommended since they have been tested to be compatible with
this unit.
manufacturers, sometimes it may not be possible to play back
depending on the disc and recording conditions.
● It is impossible to record on CD-R/RW or DVD-R discs used for
authoring.
● When recording copy-once programs of digital broadcasts,
record in VR mode using CPRM compatible DVD-RW discs.
DVD-RAM Discs
It is only possible to use discs which conform with DVD-RAM
standard Version 2.0, 2.1 or 2.2.
● If you use a disc formatted under a different standard version,
format it on this unit before use.
NOTE:
The following may result if you play back a DVD-R disc recorded
on another unit.
● The disc does not play.
● It may not be possible to record, play back, edit or dub a
DVD-RAM disc even if it conforms to the standard if it was
recorded or edited on the devices from other manufacturers or on
a PC, or if it has far too many titles, or if there is very little
available capacity remaining on the disc.
● A mosaic pattern (block noise) appears on the screen.
● Video or audio may be dropped out.
● The unit stops during playback.
● DVD-RAM discs recorded on this unit cannot be played back on
an incompatible DVD player.
● It is possible to record copy-once programs of digital broadcasts
only onto 4.7/9.4 GB DVD-RAM discs. (2.8 GB DVD-RAM discs
are not compatible)
● This unit does not support discs contained in cartridges. Use the
disc after removing it from the cartridge. For details on discs in
TYPE2 and TYPE4 (disc removable) cartridge, refer to its
instruction manual.
● While recording, it is possible not only to start playback of a
program currently being recorded, but also to watch another
program previously recorded.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
8
EN
Discs For Playback Only
Unplayable Discs
You can use discs with the following logos for playback only.
The unit may not be able to play back or it may take some time to
read a disc depending on the recording status or condition of the
disc, or if the disc is scratched, dirty or warped.
In addition, do not attempt to play back discs in unusual shapes
(heart-shaped, octagonal, or other forms). If such discs are
accidentally played back, it may cause noise that can lead to
speaker damage.
DVD VIDEO
Video CD/Super Video CD
(example of region code
indications)
● CD-ROM discs (including PHOTO-CD and CD-G)
● Discs recorded in Packet Write (UDF) format
● 1.3 GB double density CDs (DDCD)
● High density CDs (HDCD)
The following discs also cannot be played back.
● Discs of a region number other than A1B
● DVD-RAM (2.6 GB/5.2 GB)
Audio CD
CD-DA files
CD-R
CD-DA/JPEG/
MP3 files
● DVD-RAM (TYPE1)
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the
“Compact Disc Digital Audio” standard. Therefore, the use of Non-
DVD side of a DualDisc on this product may not be recommended.
CD-ROM
JPEG/MP3 files
CD-RW
CD-DA/JPEG/
MP3 files
Region Number
The world is divided into 6 regions for DVD VIDEO discs.
DVD VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played back
on this unit unless the region number of the disc matches that of
the unit. The region number for this unit is A1B. Only discs whose
region number includes A1B or AALLB can be played back such as
shown below.
● Playback may not be performed depending on the characteristics
and condition of the disc used.
● DTS Audio CDs can also be played back. (An optional DTS
decoder is required)
● MP3 and JPEG discs can be played back on this unit only when
they have been recorded in the ISO9660 or Joliet format and
finalized.
● JPEG files that can be played back on this unit must conform to
JFIF/Baseline process, and the maximum resolution of a JPEG
file is 2,812 pixels in width and 2,112 pixels in height.
● CD-R/RW discs recorded in music CD format need to be finalized
to play back on this unit.
Examples of DVD VIDEO labels which can be played back
using this unit.
● Operation and audio quality of this unit are not guaranteed for
discs that do not conform to the Compact Disc specification
(CD-DA).
Marks of discs in this instruction manual
Before you play back a CD, check for the CD logo and read the
notes on the package to confirm that it conforms to the Compact
Disc specification.
Allows operation with a
DVD-RAM disc.
Allows operation with a
Video CD/Super Video
CD (SVCD) disc.
● Depending on the intentions of the author of the software,
recording conditions of DVD discs and Video CD/SVCD discs
may be restricted. Since this unit plays back discs according to
the intentions of the author of the software as indicated on the
disc, some functions may not operate as commanded.
● When switching from the first layer to the second layer of double-
layered DVD VIDEO discs, the image and sound may be
momentarily distorted. This is not a malfunction.
● DVD-AUDIO discs compatible with DVD video players can be
played.
Allows operation with a
DVD-R disc.
Allows operation with
an Audio CD disc.
Allows operation with a
DVD-RW disc.
Allows operation with a
disc including MP3
files.
Allows operation with a
DVD VIDEO disc.
Allows operation with a
disc including JPEG
files.
● Super Audio CDs (SACD) compatible with conventional CD
players can be played.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
9
Audio CD/Video CD/SVCD
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video CD/
SVCD discs.
However, some discs are not divided into tracks.
Recording Medium And Format
DVD-RAM
● Recording and erasing can be performed as many times as
possible on a disc.
● Editing can be performed after recording, such as deleting
unwanted parts.
● While recording, it is possible not only to start playback of a
program currently being recorded, but also to watch another
program previously recorded.
Audio CD/Video CD/SVCD
Track 1
Track 2
Track 3
Track 4
DVD-RW (VR mode)
● Recording and erasing can be performed as many times as
possible on a disc.
● Editing can be performed after recording, such as deleting
unwanted parts.
JPEG/MP3 Disc (CD-R/RW/ROM)
MP3/JPEG files put in directories nested in several levels on a disc
will be organized as if they were put in single level directories
(groups) by the MP3/JPEG Navigation of this unit. (A pg. 52)
File structure of a disc before starting the MP3/JPEG
Navigation
DVD-RW (Video mode)
● Can be played back on other DVD players after finalizing.
● New recording can be performed by erasing all the data on a disc
once played back.
DVD-R
● Can be played back on other DVD players after finalizing.
● Suitable when keeping a recorded disc for a long time.
File Structure Of Discs
Directory
MP3 file
JPEG file
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
“titles”. Each title has a number (title number) that can be used to
select desired titles. Titles are further divided into units called
“chapters”. Each chapter has a number (chapter number) that can
also be used to select desired chapters. Note that some discs are
not divided into titles and chapters.
File structure of the disc after starting the MP3/JPEG
Navigation
Files are automatically grouped as follows and displayed on the
MP3/JPEG Navigation screen. Data is displayed in the
alphabetical order of file name. Files are grouped based on roots.
disc
A single recording session results in a single title. In addition,
chapter marks are automatically inserted when recording is
paused, or audio changes from monaural to stereo due to
commercial breaks, etc. It is also possible to insert chapter marks
at desired locations during playback. (A pg. 25)
When you record a program on a DVD-R/RW (Video mode)
disc
A single recording session results in a single title. Marks are
assigned automatically approximately every 5 minutes during
recording. In addition, chapter marks are automatically inserted
when recording is paused, or audio changes from monaural to
stereo due to commercial breaks, etc. It is possible to insert
chapter marks at desired locations during playback. Once the disc
has been finalized, these chapter marks are deleted and new
chapter marks are assigned automatically approximately every
5 minutes.
● This unit can recognize up to 9 hierarchies including directories
and files.
DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc
Also, it can recognize up to 250 files in each group, and up to
99 groups on a disc.
Title 1
Title 2
Chapter 1
NOTES:
Chapter 2
Chapter 3
Chapter 1
Chapter 2
Chapter 3
● Video CD/SVCD discs that support Playback Control (PBC)
The contents of a disc are recorded into several hierarchies, and
played back according to the instructions on the screen while
navigating through the hierarchies. It is also possible to playback
recorded tracks consecutively without activating the PBC function
even when playing a PBC-compatible disc. (A pg. 26)
● Regarding the contents recorded on discs
Some files may not be played back depending on the file types
and other factors.
● In Video mode, even before finalizing, it is impossible to perform
editing operations other than changing the disc name and/or title
names and deleting programs and/or titles.
● After finalizing, it is impossible to perform editing operations.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
10
DVD VIDEO Marks
Placing A Disc
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of the disc. Check the marks indicating the contents and
functions of the disc. Note, however, that in some cases a disc
may not include a mark even for a function it supports.
Opening the disc tray
Press M to open the disc tray.
Marks related to video
Number of subtitles
Number of angles
CH+
DV
DV IN
F-1
Recorded under the
standard 4:3 aspect
ratio
Screen includes
black bands at the
top and the bottom
of image which has
a standard 4:3
aspect ratio (letter
box)
S
-
VIDEO
VIDEO
L(MONO)
AUDIO
R
● Pressing the button again closes the disc tray.
● Use the button to open and close the disc tray.
● Do not block the disc tray with your hand while it is opening or
closing as this may result in hardware failure.
● Do not place unplayable discs or any object other than a disc on
the disc tray.
Video playback is in Wide video mode (16:9)
on wide televisions, but in letter box on
televisions with standard 4:3 aspect ratio.
● Do not press down strongly on the disc tray or place any heavy
objects on it.
Video playback is in Wide video mode (16:9)
on wide televisions, but pan and scan is used
on televisions with standard 4:3 aspect ratio
(either the left or right side of the image is cut-
out).
Discs without cartridges
Marks related to audio
+
-
CH
-
H
O
P
EN
S
U
P
CH
Number of audio tracks
R
E
I
V
S
S
E
R
G
O
R
P
T
C
E
I
R
D
L
A
T
I
I
G
D
Dolby Digital mark
It has been developed by Dolby Laboratories as
a digital surround system.
Label side facing up
Disc tray
Place the disc on the disc tray with the label side facing up. Since
disc size changes depending on the disc to be played back, be
sure to correctly align the disc with the grooves for its size. If the
disc is not in its groove, it may be scratched or otherwise
damaged. To insert an 8 cm disc, place it according to the inner
groove.
DTS (Digital Theater Systems)
You can enjoy DTS audio if you connect an
amplifier with a built-in DTS decoder to the
DIGITAL OUT connector of the unit.
DVD-RAM discs contained in cartridges
Double-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the side
you wish to play back or record facing down. If you insert the disc
with “Side A” facing down, programs are recorded on side A.
Single-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the label
side facing up.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
EN
11
Care And Handling Of Discs
How to handle discs
When handling a disc, do not
touch the surface of the disc.
Since discs are made of
plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped, the
images and sound will not be
picked up correctly, and such a
disc may cause the unit to malfunction.
Label side
Do not damage the label side, stick paper to or use any adhesives
on its surface.
Recording side
Make sure that discs are not scratched and dirty on the recording
side before use. Scratches and dirt on the recording side of a disc
may hinder proper playback and recording. Also be careful that a
DVD-RAM disc may get scratched or dirty when removed from
cartridge then put back in after use.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt adhering
to a disc, wipe with a soft dry cloth, moving
from the centre outwards.
If a disc is difficult to clean, wipe with a cloth
moistened with water. Never use record
cleaners, petrol, alcohol or any anti-static
agents.
CAUTION:
Sometimes during playback, noise may appear or images may
be garbled. This is sometimes due to the disc. (It may not be up
to industry standards.)
These symptoms are caused by the discs, not by the
malfunction of the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
12
Front View
A B
C
D
E
F
G
+
CH
RAM/RW
STANDBY/ON
DV
DV IN
F-1
S-VIDEO
VIDEO
L(MONO)
AUDIO
R
H
I
J
K L
H Front Display Panel
I S-video Input Connector [S-VIDEO]
A Standby/On Button (STANDBY/ON A)
B Infrared Beam Receiving Window
C Disc tray
J Video/Audio Input Connectors [VIDEO/AUDIO (L(MONO)/
R)]
D Eject Button (M)
K DV Input connector [DV IN (A*)]
E Record Button (R)
F Stop Button (o)
G Play Button (I)
*
i (i.Link) refers to the IEEE1394-1995 industry specification and
extensions thereof. The i logo is used for products compliant with the
i.Link standard.
L Channel Buttons (CH +/–)
To access covered connectors,
press PUSH-OPEN to open the
cover.
CH+
PUSH-OPEN
CH
-
Rear View
A
B
C
D
E
F
G
H
I J
COMPONENT
Y
L-1
IN
VIDEO
VIDEO
AUDIO
LEFT
AUDIO
LEFT
PB
S-VIDEO
S-VIDEO
PCM/STREAM
OUT
PR
RIGHT
RIGHT
L-1
COAXIAL
ANTENNA
OUTPUT
INPUT
DIGITAL OUT
K
L
M
A Antenna Input Connector [ANTENNA IN]
B Component Video Output Connectors [COMPONENT
VIDEO OUT (Y/PB/PR)]
C Video Output Connector [VIDEO OUTPUT]
D S-video Output Connector [S-VIDEO OUTPUT]
E Video Input Connector [VIDEO INPUT L-1]
F S-video Input Connector [S-VIDEO INPUT L-1]
I Region Number
J AC Power Cord
K Antenna Output Connector [ANTENNA OUT]
L Audio Output Connector [AUDIO OUTPUT]
M Audio Input Connector [AUDIO INPUT L-1]
G Digital Audio Output Connector [DIGITAL OUT (COAXIAL)]
H Cooling Fan
● This prevents the temperature from rising inside the unit. Do not
remove it.
● The unit may become hot when it is turned off, as the cooling
fan on the rear of the unit is not activated. However, the cooling
fan may be activated in the following cases;
^ In the Automatic Satellite Program Recording standby mode
(A pg. 42).
^ When AAUTO CLOCKB is set to AONB (A pg. 19).
(Set AAUTO CLOCKB to AOFFB if you mind the noise of the
fan.)
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
13
Front Display Panel
G
H
A
B
C
D
E
F
I
LPCM
FR
DISC
XP SP LP EP
RW VCD
-RAM
VR
-
DVD
N
J
K
O
P
L
M
A Disc Type Indicator
G Random/Program Playback Mode Indicator (RND/PRGM)
A pg. 33
ARNDB: Lights when Random Playback mode is set.
APROGB: Lights when Program Playback mode is set.
H Repeat Mode Indicator (x/1/A-B) A pg. 30, 31
When a disc is loaded, the type of the disc is indicated.
Disc Status Indicator
When a disc is running, the disc marks rotate.
During High-Speed Search:
Rotate faster than normal playback.
During Slow Motion:
Rotate slower than normal playback.
While recording:
AxB:
Ax1B:
Whole disc is played back repeatedly.
A single title/chapter/track is played back
repeatedly.
Inner red ring lights in the same way as normal playback.
During Instant Timer Recording (ITR), inner red ring slowly
blinks.
AxA-BB: The selected part (A-B) is played back repeatedly.
No display: Repeat Playback mode is off.
I DISC Timer Indicator A pg. 39
While paused:
Disc marks blink when either recording or playing back.
While stopped:
While resume stopped:
No disc on the disc tray: Disc marks all light out.
VR Mode Indicator (VR) A pg. 63
:
Lights when a disc set up for On-Disc Timer
Programming is loaded.
Lights when timer recording other than On-Disc
Timer Programming is on stand-by or being
executed.
Lights when On-Disc Timer Programming is on
stand-by or being executed.
Disc marks all light.
Disc marks all blink.
:
:
Lights when a DVD-RW disc is formatted in VR mode.
B Linear PCM Indicator (LPCM)
:
Blinks quickly if you press TIMERj in the
following cases;
Lights when AXP MODE REC AUDIOB is set to ALINEAR PCMB
(A pg. 59) for recording with DVD-RAM, DVD-R and DVD-RW
discs, and when Linear PCM audio is played.
C Recording Mode Indicator (XP/SP/LP/EP/FR) A pg. 34
Blinks when recording mode is being set.
● Disc is not loaded.
● Clock has not been set.
● There is no program setting.
J Video Output Indicator (q) A pg. 60
No display: Indicates that interlace mode is engaged.
While AFRB is blinking, the left 3 digits of the Multi Display (L
M) indicate setting values ranging from A60B to A480B. After the
value has been set, only AFRB lights.
q:
Indicates that progressive mode is engaged.
(Example) q lights when video output mode is in progressive
mode.
D Group/Title Indicator (GRP/TITLE)
K Automatic Satellite Program Recording Indicator A pg. 42
Lights when the unit is in the Auto Satellite Program Recording
standby mode.
L Group/Title Number Display
M Track/Chapter Number Display
N Remaining Time/Elapsed Time Display A pg. 25, 35
Lights when remaining time of DVD-RAM, DVD-R and
DVD-RW discs is displayed, and lights out when elapsed time
is displayed.
The right 6 digits of the Multi Display (O) indicate elapsed or
remaining time of each track.
No display: Indicates elapsed time of the disc.
Displayed: Indicates remaining time of the disc.
O Remaining Time/Elapsed Time Display A pg. 25, 35
P Multi Display
AGRPB or ATITLEB lights depending on a disc loaded while the
left 2 digits of the Multi Display (L) indicate the numbers
explained below.
AGRPB: Total number of groups or group number being played
back are displayed on the Multi Display.
ATITLEB: Total number of titles or title number being played
back are displayed on the Multi Display.
E Channel Indicator
Indicates the channel received.
F Track/Chapter Indicator (TRK/CHAP)
ATRKB or ACHAPB lights depending on a disc loaded while the
3rd and 4th digits from the left of the Multi Display (M) indicate
the numbers explained below.
ATRKB: Total number of tracks or track number being played
back are displayed on the Multi Display.
ACHAPB: Chapter number being played back are displayed on
the Multi Display.
Displays clock, received channel, elapsed time, and remaining
time.
Also displays status of the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
14
Q Audio Button (AUDIO) A pg. 26
Remote Control
U TV Volume Buttons (TV VOL)
A
B
For adjusting the volume of a JVC TV.
V Channel Buttons (CH +/–) A pg. 34
W Memo Button (MEMO) A pg. 44
S
T
Mark Button (MARK) A pg. 25
X Timer Button (TIMERj) A pg. 37, 38
a Enter Button (ENTER)
U
C
Forward Slow Button (SLOW +) A pg. 24
e Play Button (I) A pg. 22, 23, 28
f Pause Button (W) A pg. 22, 29
V
W
D
E
g Stop Button (o) A pg. 22
Clear Button (CLEAR) A pg. 32
F
G
X
Y
i One Touch Replay Button (w) A pg. 24, 29
j Angle Button (ANGLE) A pg. 25
Live Check Button (LIVE CHECK) A pg. 27, 29
k Set Up Button (SET UP) A pg. 18, 58
l Progressive Scan Button (PROGRESSIVE SCAN) A pg. 32,
60
Z
H
I
a
b
c
J
K
L
How To Use
Before use, insert two AA size batteries into the remote control
with the polarity (F and G) matched correctly as indicated on
the battery compartment or on the lid.
d
e
f
g
h
i
● Point the remote control toward the receiving window.
● The maximum operating distance of the remote control is
about 8 m.
M
N
O
NOTE:
If the remote control doesn’t work properly, remove its batteries,
wait a short time, replace the batteries and then try again.
P
Q
R
j
k
l
A TV/INPUT Button
B Open/Close Button (M)
C Number Keys A pg. 23, 32, 33
Character Keys A pg. 46
E Auxiliary Button (AUX)
F VCR Plus+ Button A pg. 37
G Program Buttons (PROG) A pg. 38
I Selection Keys (FGD E)
J Menu Button (MENU) A pg. 23
K Reverse Skip Button (S) A pg. 23, 26, 29, 33
Reverse Slow Button (SLOW –) A pg. 23
M Record Button (R) A pg. 34, 35
N On-Screen Button (ON SCREEN) A pg. 15, 30
O Display Button (DISPLAY) A pg. 25, 35
P Recording Mode Button (REC MODE) A pg. 34, 42
Remain Button (REMAIN) A pg. 25, 35
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
EN
15
When using Live Memory playback
On-Screen Display
When ON SCREEN on the remote control is pressed, various
operational indicators appear on the TV screen. To clear the
operational indicators, press ON SCREEN twice.
A
B
TITLE2
0:12:27
TITLE2
CHAPTER1
DVD-RAM
6:36PM
LP
EACH 0:13:34
STEREO
CH 10
When playing back a recorded title
C
D
E
F
G
A Disc type
B Current time
C Bar meter for recording/playback
D Recording mode
A
B
C
D
E
TITLE1
CHAPTER1
DVD-VIDEO
LPCM 2ch
EACH 0:01:08
E Current playback time/Elapsed recording time
F Audio mode
G Recording channel number
F
G
A Disc type
B Audio mode
C Current status (playback)
D Playback title number
E Playback chapter number
F Current playback point
G Elapsed playing time
DV Dubbing
When capturing images from the external DV
equipment
A
B
TITLE12
CHAPTER--
DVD-RW/VR
--:--
SP
When recording
EACH 0:00:00
L
R
DV
A
B
C
C
D
E
F
G
A Disc type
B Current time
TITLE14
CHAPTER1
DVD-RW/VR
6:04PM
SP
EACH 0:01:23
STEREO
CH 95
C Current recording point
D
E
F
G
H
D Current status (recording)
E Elapsed recording time
F Sound mode
A Disc type
B Recording mode
C Current time
D Recording point
E Current status (recording)
F Elapsed recording time
G Audio mode
G Recording channel (DV input)
DV DUBBING
AUDIO 1
1
2
DV
DV
A
B
C
H Recording channel number
A Displays when remote control is set to DV control mode.
B Auto capture button
C Sound monitor switch
When pressing REC MODE:
(Appears for eight seconds.)
REC QUALITY
RECORDABLE TIME
1:00
2:00
4:01
6:03
XP:
SP:
LP :
EP:
FR:
2:31 (FR150)
A
B
A Recording mode
B Remaining disc time for each recording speed
During Instant Timer Recording (ITR)
TITLE13
CHAPTER1
SP
A
0:13
ITR
A Record remaining time
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING YOUR NEW UNIT
EN
16
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
Basic Connection
1 Make sure the package contains all of the accessories listed in
“SPECIFICATIONS” (A pg. 69).
Antenna or Cable
2 Place the unit on a stable, horizontal surface.
3 Connect the unit to a TV depending on the TV and cables you
use.
Coaxial cable
8 Simple Connections
To connect to TV’s VIDEO input and AUDIO input connectors
^
Flat feeder
A Disconnect the TV aerial cable from the TV.
B Connect the TV antenna cable to the [ANTENNA IN] connector
on the rear panel of the unit.
C Connect the [ANTENNA OUT] connector on the rear panel of
the unit and the TV’s antenna connector with the supplied RF
cable.
D Connect the supplied video/audio cable between the [VIDEO/
the TV’s VIDEO/AUDIO input connectors.
Matching transformer (not
supplied)
AC Outlet
To
[ANTENNA IN]
AC Power Cord
● Set your TV to VIDEO mode (or an input mode such as EXT1).
8 S-Video Connection
To connect to TV’s S-VIDEO input and AUDIO input
connectors ^
A Perform steps A – C of “Simple Connections”.
B Connect the unit’s [S-VIDEO OUTPUT] connector to the TV’s
S-VIDEO input connector.
Back of unit
To
[ANTENNA
OUT]
To [S-VIDEO
OUTPUT]
To [VIDEO/
AUDIO
OUTPUT]
To
[COMPONENT
VIDEO OUT (Y/
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
PB/PR)]
● If your TV is not stereo-capable, use the unit’s [AUDIO
OUTPUT] connectors to connect to an audio amplifier for Hi-Fi
stereo sound reproduction.
Video/Audio
cable (supplied)
Component
video cable
(not supplied)
S-Video Cable
(not supplied)
8 Component Video Connection
To connect to TV’s component video input connectors ^
A Perform steps A – C of “Simple Connections”.
B Connect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)]
connectors to the TV’s component video input connectors.
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
RF cable
(supplied)
● If your TV is not stereo-capable, use the unit’s [AUDIO
OUTPUT] connectors to connect to an audio amplifier for Hi-Fi
stereo sound reproduction.
TV
To 75 ohm
terminal
● By using the component video connection, you can view the
images in the progressive mode. For switching to the
progressive mode, refer to “Scan Mode Set” (A pg. 60).
It’s essential that your unit be properly connected.
4 Plug the end of the AC power cord into an AC outlet. This unit
performs Plug & Play Set automatically.
● ALOADINGB blinks on the front display panel when the AC plug
of the power cord is connected into an AC outlet. And it takes
approximately 30 seconds for the unit to be turned on. This is
not a malfunction.
ATTENTION:
Connect the AC plug only after all connections to the TV has
been completed.
NOTE:
It is necessary to connect any of above audio/video connections in
addition to antenna connection with RF cable in order to view DVD
playback on the TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
17
1 Connect the antenna cable to the unit. (A pg. 16) Then connect
the AC power cord to an AC outlet. Do not turn on the unit. The
clock and tuner channels will be set automatically.
● ALOADINGB blinks on the front display panel when the AC plug
of the power cord is connected into an AC outlet and it takes
approximately 30 seconds for the unit to be turned on. This is
not a malfunction.
Plug & Play Set
Auto Clock Set/Auto Tuner Set
This unit sets the clock and tuner channels automatically when AC
power cord is first connected to an AC outlet. The antenna cable
must be connected for the Plug & Play setting.
The time and date are set automatically by the clock setting data
transmitted from one of the regular TV broadcast channels. We call
this TV channel the “host channel” and it is a PBS channel in your
area.
NOTES:
● Auto Clock Set is performed first. AAUTOB blinks on the front
display panel during Auto Clock Set.
● Auto Channel Set is performed next. Auto Channel Set scans all
Channel Set, the channel numbers are displayed as they are
● When Plug & Play setting has been completed successfully, the
correct clock time is displayed. If you perform Plug & Play setting
successfully, there is no need to perform ACLOCK SETB
(A pg. 19) and ATUNER SETB (A pg. 20). If, however, you want
to add or delete channels, refer to AMANUAL CH SETB
(A pg. 20).
ATTENTION:
Depending on areas or reception conditions, the unit may not
receive the Auto clock setting data from the PBS channel. If this
function is taking a considerable amount of time, it may be
necessary to perform the Semiauto or Manual Clock Set
procedure.
During Auto Clock Set
AAUTOB blinks.
CH+
RAM/RW
STANDBY/ON
PUSH-OPEN
CH
-
During Auto Channel Set
The channel numbers are displayed and AAUTOB blinks as
they are scanned and set.
INFORMATION
● If AAUTO CLOCKB is set to AONB (A pg. 19) the clock will be
adjusted automatically by the host channel using the incoming
PBS channel clock setting data. (This automatic clock
adjustment can only be performed when the unit is turned off.)
● If the memory backup fails, because a power outage occurs or
because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the unit.
Plug & Play Completed
The current time is displayed.
● If an incorrect clock time or A- - : - -B appears on the front
display panel, see “What to do if Plug & Play setting
failed” on the left column.
What to do if Plug & Play setting failed
● If an incorrect time is displayed on the front display panel, you
may be receiving the clock setting data of a PBS channel from
an adjacent time zone, or an incorrect PBS channel from a
cable TV system. In this case, perform “Semiauto Clock Set”
(A pg. 19) or “Manual Clock Set” (A pg. 19).
Host PBS signal available in your area. Ensure that the
antenna cable is connected correctly. Then turn on and off the
unit; the Plug & Play setting will be automatically reactivated. If
Plug & Play setting is not performed though the antenna cable
is connected correctly, perform “Manual Clock Set” (A pg. 19)
and “Auto Channel Set” (A pg. 20) or “Manual Channel Set”
(A pg. 20).
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
18
On-screen Language Set
This unit offers you the choice to view on-screen messages in 3
different languages.
Language
● Turn on the unit.
1 Press SET UP to access
● Turn on the TV and select an input mode such as EXT1.
DVD SET UP
FUNCTION SET UP INITIAL SET UP
OTHERS
the Main Menu screen.
VIDEO IN/OUT RECORDING SET DISPLAY SET
2 Press selection keys to
select AFUNCTION SET
UPB, then press ENTER.
SUPERIMPOSE
GRAY BACK
AUTO
ON
BRIGHT
OFF
DIMMER
POWER SAVE
ON SCREEN LANGUAGE
3 Press selection keys to
select ADISPLAY SETB,
then press ENTER.
ENGLISH
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
4 Press selection keys to
select AON SCREEN
LANGUAGEB, then press ENTER.
5 Press selection keys to select your desired language, then
press ENTER.
Selection Keys (FGD E)
ENTER
6 Press SET UP to complete the setting.
Menu/Audio/Subtitle Language Set
Some DVD discs contain the DVD menu display, audio and
subtitles in multiple languages. With these discs, you can set the
default language as you like.
● The procedure shows how to set AMENU LANGUAGEB as an
example.
SET UP
1 Press SET UP to access the Main Menu screen.
2 Press selection keys to select ADVD SET UPB, then press
ENTER.
3 Press selection keys to
DVD SET UP
FUNCTION SET UP INITIAL SET UP
AUDIO OUTPUT UTILITY
select ALANGUAGE
SETB, then press
ENTER.
LANGUAGE SET
MENU LANGUAGE
ENGLISH
ENGLISH
ENGLISH
AUDIO LANGUAGE
SUBTITLE
SET UP
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
EXIT
4 Press selection keys to
select AMENU
DVD SET UP
FUNCTION SET UP INITIAL SET UP
AUDIO OUTPUT UTILITY
LANGUAGE SET
LANGUAGEB, then press
ENTER.
MENU LANGUAGE
ENGLISH
GERMAN
E
AUDIO LANGUAGE
SUBTITLE
5 Press selection keys to
select your desired
language, then press
ENTER.
● See “Language Code
List”. (A pg. 68)
OFF
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
6 Press SET UP to complete the setting.
NOTE:
When the selected language is not available on the disc, the disc’s
default menu language is played back.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
19
OFF:
Select when Daylight Saving Time does not apply to
you.
Clock Set
7 Press selection keys to
select ATIME ZONEB,
then press ENTER.
DVD SET UP
TUNER SET
FUNCTION SET UP INITIAL SET UP
CLOCK SET
Perform clock setting only if the clock has not been set correctly by
the Plug & Play setting.
AUTO CLOCK
HOST CH [CATV]
ON
Press selection keys to
select AAUTOB or the
desired time zone, then
press ENTER.
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
AUTO
AUTO
AUTO
D.S.T.
TIME ZONE
HAWAII
Each time you press
selection keys, the time
zone changes as follows:
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
YAUTOYATLANTICYEASTERNYCENTRALYMOUNTAIN
YPACIFICYALASKAYHAWAIIY(back to the beginning)
NOTE:
If an incorrect time is displayed by the Plug & Play function, you
may be receiving the clock setting data of a PBS channel from an
adjacent time zone or from an incorrect PBS channel from a cable
TV system. If you selected AAUTOB for the host channel in step 5,
be sure to select the correct time zone manually.
Selection Keys (FGD E)
ENTER
8 Press SET UP to end.
IMPORTANT:
Turn off the unit after performing Semiauto Clock. AAUTOB will
appear on the front display panel while the clock is being set. The
current clock time will appear automatically when the clock setting
is completed.
SET UP
AUTO DAYLIGHT SAVING TIME
This function enables automatic adjustment of the unit’s clock at
the start and end of Daylight Saving Time.
Semiauto Clock Set
You can change the host channel/D.S.T. (Daylight Saving Time)/
time zone setting manually.
With DST set to AONB^
^
^
on the first Sunday of April at 2:00 AM, the clock is adjusted to 3:00 AM.
on the last Sunday of October at 2:00 AM, the clock is adjusted to 1:00 AM.
NOTE:
The time set previously will be erased when AAUTO CLOCKB,
AHOST CH [CATV]B, AD.S.T.B or ATIME ZONEB setting is changed.
NOTE:
Timer recording may not function correctly at the time Daylight
Saving Time is adjusted.
1 Press SET UP to access the Main Menu screen.
2 Press selection keys to
DVD SET UP
TUNER SET
FUNCTION SET UP INITIAL SET UP
CLOCK SET
Manual Clock Set
select AINITIAL SET UPB,
then press ENTER.
AUTO CLOCK
HOST CH [CATV]
ON
1 Press SET UP to access the Main Menu screen.
3 Press selection keys to
select ACLOCK SETB,
then press ENTER.
AUTO
AUTO
AUTO
2 Press selection keys to select AINITIAL SET UPB, then press
D.S.T.
ENTER.
TIME ZONE
3
4
Press selection keys to select ACLOCK SETB, then press ENTER
Press selection keys to select AUTO CLOCKB, then press ENTER
Press selection keys to select AOFFB, then press ENTER
.
A
.
SET UP
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
.
SELECT
EXIT
5 Press selection keys to select ATIMEB, then press ENTER.
Press selection keys until the desired time appears, then
press ENTER.
4 Press selection keys to
select AAUTO CLOCKB,
then press ENTER.
Press selection keys to
select AONB, then press
ENTER.
DVD SET UP
TUNER SET
FUNCTION SET UP INITIAL SET UP
CLOCK SET
AUTO CLOCK
HOST CH [CATV]
ON
● The confirmation screen appears.
AUTO
AUTO
6 Press selection keys to select AOKB, then press ENTER for
10
D.S.T.
confirmation.
TIME ZONE
7 Set ADATEB and AYEARB
5 Press selection keys to
select AHOST CH
[CATV]B, then press
ENTER.
DVD SET UP
TUNER SET
FUNCTION SET UP INITIAL SET UP
CLOCK SET
in the same way as in
step 5.
SET UP
EXIT
OK
SELECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
AUTO CLOCK
OFF
- - : - -
1/1 (SAT)
2005
● Holding F G changes
the time in 30-minutes
interval, or changes the
date in 15-days interval.
TIME
DATE
YEAR
D.S.T.
Press selection keys to select AAUTOB or the desired PBS
channel number, then press ENTER.
NOTE:
2006
8 Press selection keys to
Some PBS channels do not transmit clock setting data.
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
select AD.S.T.B, then
SELECT
Press selection keys to select the desired setting, then press
ENTER.
press ENTER. Press
selection keys to select the desired setting, then press
ENTER.
ON:
OFF:
Adjustment will be made by the built-in clock itself.
Select when Daylight Saving Time does not apply to
you.
AUTO: Select if you want to adjust your unit’s clock
automatically by the incoming signal from the host
channel. Be sure to select the correct time zone
manually in step 7.
9 Press SET UP to complete the setting.
ON:
Adjustment will be made by the built-in clock itself.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
20
Manual Channel Set
You can add the channels you want or delete the channels you do
not want manually.
Tuner Set
● Turn on the unit.
1 Press SET UP to access the Main Menu screen.
2 Press selection keys to
● Turn on the TV and select an input mode such as EXT1.
DVD SET UP
TUNER SET
FUNCTION SET UP INITIAL SET UP
CLOCK SET
select AINITIAL SET UPB,
then press ENTER.
BAND
CATV
3 Press selection keys to
select ATUNER SETB,
then press ENTER.
AUTO CH SET
MANUAL CH SET
GUIDE CHANNEL SET
4 Press selection keys to
select AMANUAL CH
SETB, then press
ENTER.
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
5 Add or skip the desired channels.
Selection Keys (FGD E)
ENTER
To add channels
DVD SET UP
FUNCTION SET UP INITIAL SET UP
1
A Press selection keys to
INITIAL SET UP / MANUAL CH SET
RETURN
select ACH [CATV]B, then
press ENTER.
B Press selection keys to
select a channel number
you want to add, then
press ENTER.
C Press selection keys to
select AADD/SKIPB, then
press ENTER.
CH [CATV]
ADD/SKIP
RETURN
SKIP
ADD
SKIP
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SET UP
SELECT
D Press selection keys to select AADDB, then press ENTER.
E Repeat A ^ D to add other channels.
To skip channels
A Press selection keys to select ACH [CATV]B, then press
ENTER.
B Press selection keys to select a channel number you want to
skip, then press ENTER.
C Press selection keys to select AADD/SKIPB, then press
ENTER.
NOTE:
The unit selects the correct band (TV or CATV) automatically
during Auto Channel Set. The selected band will be displayed on
the right side of ABANDB on the Tuner Set screen.
D Press selection keys to select ASKIPB, then press ENTER.
E Repeat A ^ D to skip other channels.
Auto Channel Set
Perform Auto Channel Set only if channels have not been set
correctly by the Plug & Play setting.
6 Press SET UP or RETURN twice to complete the setting.
1 Press SET UP to access the Main Menu screen.
2 Press selection keys to
DVD SET UP
TUNER SET
FUNCTION SET UP INITIAL SET UP
CLOCK SET
select AINITIAL SET UPB,
then press ENTER.
BAND
CATV
3 Press selection keys to
select ATUNER SETB,
then press ENTER.
AUTO CH SET
MANUAL CH SET
GUIDE CHANNEL SET
4 Press selection keys to
select AAUTO CH SETB,
then press ENTER.
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
● You can automatically
set the receivable channels in your area in the order of their
frequencies.
● When Auto Channel Set is completed, ASCAN COMPLETEDB
appears on screen.
● If the scan was unsuccessful, ASCAN COMPLETED-NO
SIGNAL-B appears on screen. Check the connections and start
again.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
EN
21
1 Press SET UP to access the Main Menu screen.
Monitor Set
2 Press selection keys to
select AFUNCTION SET
UPB, then press ENTER.
DVD SET UP
FUNCTION SET UP INITIAL SET UP
VIDEO IN/OUT RECORDING SET DISPLAY SET
OTHERS
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
MONITOR TYPE
FRONT AUX F-1
REAR AUX L-1
4:3LB
3 Press selection keys to
select AVIDEO IN/OUTB,
then press ENTER.
VIDEO
VIDEO
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
SET UP
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
EXIT
4 Press selection keys to
select AMONITOR
TYPEB, then press
ENTER.
DVD SET UP
FUNCTION SET UP INITIAL SET UP
OTHERS
VIDEO IN/OUT RECORDING SET DISPLAY SET
MONITOR TYPE
FRONT AUX F-1
REAR AUX L-1
4:3LB
4:3LB
4:3PS
16:9AUTO
5 Press selection keys to
select the desired
setting, then press
ENTER.
16:9FIX
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
Selection Keys (FGD E)
ENTER
6 Press SET UP to
SELECT
complete the setting.
* The boldface settings in the table below indicate the settings at your
purchase.
8 MONITOR TYPE ^ 4:3LB / 4:3PS / 16:9AUTO / 16:9FIX
4:3LB (Letter Box conversion):
SET UP
Select this when the aspect ratio of your TV is 4:3 (conventional
TV). While viewing a wide screen picture, the black bars appear
on the top and the bottom of the screen.
4:3PS (Pan&Scan):
Select this when the aspect ratio of your TV is 4:3 (conventional
TV). While viewing a wide screen picture, the black bars do not
appear; however, the left and right edges of the pictures will not
be shown on the screen.
16:9AUTO (Wide television conversion):
Select this when the aspect ratio of your TV is 16:9 (wide TV).
16:9FIX (Wide television conversion):
Select this when the aspect ratio of your TV is fixed to 16:9
(wide TV). The unit automatically adjusts the screen width of
the output signal correctly when playing back a picture whose
aspect ratio is 4:3.
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen TV
with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect ratio.There
are two styles to display the image, “Pan&Scan” (PS) and “Letter
Box” (LB).
Pan&Scan
The right and left side of the image are cut off.
The image fills the screen.
● The picture will be shown in the A4:3LBB
mode depending on the disc even if the
A4:3PSB is selected.
Letter Box
Black bands appear at the top and bottom of
the image. The image itself appears in 16:9
aspect ratio.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
22
To play back an MP3/JPEG disc, see “Playback With MP3/JPEG
Navigation” (A pg. 52).
Basic Playback
1 Load a disc.
● For details, refer to “Placing A Disc” (A pg. 10).
● Pressing M also closes the disc tray.
● Playback begins automatically if an auto-playback DVD disc is
loaded.
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
2 Press I to start playback.
● With Video CD/SVCD discs with PBC control or some DVD
discs, the menu display may appear on the TV screen after
starting playback. In this case, select an item which you want to
play back from the menu. For details, refer to “Playback Control
(PBC) Function” (A pg. 26) or “Locating A Desired Scene
Using The DVD Menu” (A pg. 23).
I
M
RAM/RW
o
● The Library Database Navigation also enables you to search
and scan the beginning of the desired titles. (A pg. 44)
M
3 Press W to pause playback.
● To resume normal playback, press I.
4 Press o to stop playback.
● When a recordable disc is played, playback stops and a
program received with the unit’s tuner resumes on the TV
screen.
● When a playback-only disc is played, playback stops and the
TV screen becomes all blue when you press o. Pressing o
again resumes a program received with the unit’s tuner.
● If M is pressed during playback, playback stops, then the disc
tray opens.
ENTER
I
NOTE:
When the Library Database Navigation screen appears, choose a
thumbnail image of the desired title on the TV screen, then press
ENTER. (A pg. 44)
W
o
ATTENTION:
● It takes approximately 30 seconds to read a disc depending on
the type and condition of the disc since this unit is multi-disc
compatible (DVD-RAM, DVD-RW, DVD-R). It may even take
several minutes when a disc is dirty, scratched or warped.
● It may take a few seconds to start playback. This is not a
malfunction.
● Forward/reverse high-speed search and other operations
cannot be performed while playback is stopped.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
23
Locating The Start Point Of The Item Or Skip The Item
Playback Features
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
Press S or T during playback.
● Pressing T locates the start point of the title (or track) or skips
to the marked point in the forward direction, then resumes
playback.
● Pressing S locates the start point of the title (or track) or skips
to the marked point in the reverse direction, then resumes
playback.
Current playback point
0-9
TOP MENU
Selection Keys (FGD E)
Previous
program
or
Scene 2
(Chapter 2)
or
Next
program
(Chapter 4)
or
Drama
or
Scene 3
(Chapter 3)
or
Movie
or
Scene 5
(Chapter 5)
or
ENTER
I
MENU
S
T
N/SLOW +
O/SLOW –
Track 3
Track 5
Track 2
Track 4
Forward
Reverse
● : marked points (A pg. 25)
Variable Speed Search
Locating A Desired Scene Using The DVD Menu
During playback, press N for forward variable speed search, or
O for reverse variable speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press I.
DVD VIDEO discs may have top menu and disc menu.
OR
Top menu
During playback, press and hold T for 2 or more seconds for
forward variable speed search, or press and hold S for 2 or more
seconds for reverse variable speed search.
● Releasing the button resumes normal playback.
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Still Picture/Frame-By-Frame Playback
Disc menu
Disc menus include playback data (angle menu, subtitle menu,
etc.) specific to each title.
Press MENU to access the disc menu.
1 Press W to pause during playback.
1 Press TOP MENU or
Example:
MENU to access the
2 Press W to activate frame-by-frame playback.
● Each press of the button advances the still picture frame by
frame.
DVD menu.
2 Press selection keys
to select the desired
title, then press
OR
Press D or E to activate frame-by-frame playback.
● Each press of D or E advances/reverses the still picture frame by
frame.
ENTER. The playback
starts.
● It may be possible to
select the desired item
using the number keys
depending on the menu
display.
● Frame-by-frame playback for reverse direction cannot be
performed with Video CD/SVCD discs.
● To resume normal playback, press I.
NOTE:
When A7B appears on the TV screen in step 1, the disc does not
have a top menu or disc menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
24
Resume Function
M
DVD A
It is possible to memorize the position where you stop playback
and resume playback from that position.
● Be sure to set ARESUMEB
DVD SET UP
FUNCTION SET UP INITIAL SET UP
to AONB or ADISC
VIDEO IN/OUT RECORDING SET DISPLAY SET
OTHERS
RESUMEB. (A pg. 60)
MARK
AUTO TIMER
RESUME
OFF
ON
TOP MENU
Selection Keys (FGD E)
ENTER
I
MENU
S
T
N/SLOW +
W
v
w
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
O/SLOW –
o
ATTENTION:
REMAIN
SUBTITLE
When a playback-only disc is played, pressing o once results in
a blue screen. To perform Resume Function with these discs,
follow the procedures as described below under the blue screen
condition.
ANGLE
1 Press o during playback to memorize a resume point.
position where you have stopped playback as a resume point.
(The inside of the disc status indicator on the front display panel
blinks while memorizing.)
Slow Motion
● The unit retains a memory of the resume points of the last
30 discs played back, even though they have been ejected if
ARESUMEB is set to ADISC RESUMEB. (A pg. 60)
● To clear the resume points:
(The inside of the disc status indicator stops blinking and
lights.)
When ARESUMEB is set to AONB:
• Press DVD A to turn off the unit.
• Press M to take out the disc.
1 Press W to pause during playback.
2 Press SLOW – (O), then press SLOW + (N).
● Each press of SLOW – (O) or SLOW + (N) increases the
slow motion speed for each direction.
● Slow motion for reverse direction cannot be performed with
Video CD/SVCD discs.
• Press o in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by
selecting an item, etc.
When ARESUMEB is set to ADISC RESUMEB:
• ARESUMEB must be set to AOFFB. (A pg. 60)
• Press o in stop mode.
OR
Press and hold S or T for 2 or more seconds.
● Releasing the button resumes normal playback.
Skip Search
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
Press v during playback.
• Press MENU to display the disc menu, then start playback by
selecting an item, etc.
● Each press initiates an approximately 30 second period of fast-
motion playback. Normal playback resumes automatically.
● This function is not possible when playing back a Video CD using
the PBC function.
playback from the resume point.
NOTES:
One Touch Replay
● ADISC RESUMEB setting works on DVD VIDEO, VCD, SVCD and
finalized DVD-R/DVD-RW (Video mode) discs. For other types of
discs, the function under AONB setting will be applied even if
ARESUMEB is set to ADISC RESUMEB. (A pg. 60)
● If you stop the playback of a disc for which a resume point has
already been memorized, the memory will be updated with the
new resume point.
● After the unit has memorized the resume points for 30 discs,
remembering a new resume point will cause the unit to delete the
oldest memorized point. Stopping playback of a disc for which a
resume point is already stored may change the order in which the
points are stored. This may potentially change the order in which
points are deleted.
You can move back the playback position slightly.
Press w.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds
and resumes pause.
● This function is not possible when playing back a Video CD using
the PBC function.
● When the unit memorizes a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
● This function may not work for some Video CD/SVCDs.
● When ARESUMEB is changed to AONB or AOFFB (A pg. 60),
resume points of the discs memorized with ARESUMEB set to
ADISC RESUMEB will be cleared.
● Resume points are memorized for each side of a double-sided
disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
25
Marking Positions To Play Back Again Later
Angle Selection
It is possible to mark positions (up to 999 points) where you want
to play back once again later, and start playback from a marked
position.
You can enjoy a variety of scene angles if a DVD VIDEO disc
contains “multi-angle” parts, where the same scene was shot from
different angles.
If the disc contains “multi-angle” parts, AyB appears on the TV
screen at the beginning of the “multi-angle” part.
To mark positions:
During playback, press MARK at
positions you want to mark.
● AMARKB is displayed on the TV
screen. You can easily locate the
marked positions using S or T
when you play back the disc.
1 Press ANGLE during
playback. The angle selection
display appears on the TV
When 3 scene angles are
screen.
contained.
2 Press ANGLE or selection
To delete the marked positions:
While paused, press S or T to
locate a marked position you want to
delete, then press MARK.
keys to select your desired
angle.
● Each time you press ANGLE or the selection keys, the angle
changes.
● Crossed AMARKB appears on the TV
screen, and the marked position is
deleted.
● When A7B appears on the TV screen, the current scene is not
recorded from multiple angles. In addition, some discs prohibit
angle selection.
● To clear the angle selection display, press ENTER. In addition,
the angle selection display disappears automatically if no
operation is done for 5 seconds.
NOTES:
● When a monaural program changes to a stereo program while
recording, a mark signal is automatically recorded.
● When a DVD-R/RW (Video mode) disc is finalized, marked points
that are marked at the desired locations during playback are
deleted and new marks are assigned automatically
approximately every 5 minutes. (A pg. 64)
Subtitle Selection
● If MARK is pressed when playing back a disc that does not allow
marks to be inserted, A7B appears on the TV screen.
Some DVD VIDEO discs contain more than one subtitle language,
from among which you can choose the desired subtitle language.
AhB appears on the TV screen at the beginning of the part where
more than one subtitle language are recorded.
Checking The Time Information
1 Press SUBTITLE during
ENGLISH
playback. The subtitle
You can check time information of a disc on the front display panel
and the TV screen.
Each press of DISPLAY changes the display as follows:
selection display appears on
the TV screen.
● Each time you press
SUBTITLE, the subtitle display
is switched on and off.
When 3 subtitle languages are
contained.
8 DVD-RAM/DVD-R/DVD-RW
During recording/playback or in stop mode
Clock time N Current title elapsed time N Disc remaining time N
(back to the beginning)
2 Press selection keys to select your desired language.
● To clear the subtitle selection display, press ENTER.
● The clock time is displayed on the front display panel only.
● The clock time and disc remaining time will not be displayed
when playing back finalized DVD-R/RW discs.
NOTES:
● For disc that does not contain subtitle language, the number of
selectable languages will not be displayed. A-/-B appears on the
TV screen.
In stop mode or during playback
● It is possible to check disc remaining time according to recording
modes also by pressing REMAIN.
● In FR mode, it is possible to set recording time in detail. While the
recording mode and the disc remaining time are displayed by
pressing REMAIN, press selection keys to select AFRB, then
select the desired recording time. (A pg. 36)
● When the subtitle language won’t be changed with the procedure
above, change the subtitle on a disc menu displayed by pressing
MENU.
● It is not possible to switch the recording mode during playback or
while recording.
8 Video CD/SVCD/Audio CD
During Playback or in stop mode
Current track elapsed time N Current track remaining time N Total
elapsed time N Total remaining time N (back to the beginning)
NOTE:
When a PBC-compatible Video CD/SVCD disc is loaded,
deactivate the PBC function. (A pg. 26)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
26
Audio Language/Sound Selection
Some DVD VIDEO discs contain the multiple audio language or
sound. You can select the desired audio language or sound. For
some Video CD/SVCD discs, you can switch the audio channel to
choose Karaoke either with or without the vocal.
0-9
1 Press AUDIO during playback.
For Example: DVD VIDEO
The Audio Language/Sound
TOP MENU
ENGLISH
selection display appears on
the TV screen.
Selection Keys (FGD E)
ENTER
RETURN
T
When 3 audio languages are
contained.
MENU
S
2 Press AUDIO or selection
keys to select your desired
audio language/sound.
I
● Each time you press AUDIO or the selection keys, the audio
language/sound changes.
o
● To clear the Audio Language/Sound selection display, press
ENTER.
AUDIO
SET UP
NOTES:
● When A7B appears on the TV screen, no audio language is
recorded.
● When the audio language won’t be changed with the procedure
above, change the audio on a disc menu displayed by pressing
MENU.
● Pressing AUDIO to select the audio language/sound is only
possible during playback. It is not possible to select by pressing
AUDIO in stop mode. However, you can select the desired audio
language/sound from the setup menu while in stop mode.
Audio Channel Selection
When watching bilingual programs or playing discs on which you
recorded bilingual or stereo programs, you can choose the desired
audio channel.
Playback Control (PBC) Function
● When ASUPERIMPOSEB is set to AAUTOB, you can confirm on
the TV screen the audio channel you have chosen. (A pg. 59)
● Each time you press AUDIO, the audio
channel changes.
Some Video CD/SVCD discs support the PBC function. PBC is an
abbreviation of “Play Back Control”. A Video CD/SVCD disc
recorded with PBC has its own menus, such as a list of the songs
on the disc. You can locate a specific scene by using the menu.
TRACK
USE
On-Screen Display
1 Press I in stop mode. The PBC menu appears.
For stereo discs
2 Press the number keys to enter the number of the desired
scene, then press ENTER. The unit starts playback of the
selected item.
For audio of left channel
For audio of right channel
● APBCB is displayed on the front display panel.
● When ANEXTB or APREVIOUSB appears on the TV screen:
Pressing T advances to the next page.
Pressing S returns to the previous page.
● You can return to the menu by pressing RETURN.
program
When the unit is connected with a digital audio device using an
optional coaxial cable and ADIGITAL AUDIO OUTB is set to
ADOLBY DIGITAL/PCMB, it is not possible to switch the audio
channel of a bilingual program recorded on a DVD-RAM or
DVD-RW (VR mode) disc. (A pg. 58). In this case, perform the
following steps using the remote control to switch ADIGITAL
AUDIO OUTB from ADOLBY DIGITAL/PCMB to APCM ONLYB.
A Press SET UP to access the Main Menu screen.
B Press selection keys to select ADVD SET UPB, then press
ENTER.
● The method of the operation is different depending on the disc.
NOTES:
● If you want to play back a PBC-compatible Video CD/SVCD disc
without activating the PBC function, start playback in stop mode
by using the number keys, instead of the I button, to choose the
track, then press ENTER.
● To activate the PBC function when a PBC-compatible Video CD/
SVCD disc is being played back without the PBC function, press
o then press I.
C Press selection keys to select AAUDIO OUTPUTB, then press
ENTER.
D Press selection keys to select ADIGITAL AUDIO OUTB, then
press ENTER.
E Press selection keys to select APCM ONLYB, then press
ENTER.
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
27
Live Memory Playback
You can watch a recorded portion of a program even before recording ends (Live Memory Playback), or watch other programs
(Simultaneous Recording and Playback) while continuing to record onto the DVD-RAM disc.
(Recording screen)
(Live Memory Playback screen)
To start Live Memory Playback,
press I to play back from the
beginning OR press w
reverse skip a little.
To stop Live Memory Playback,
press o.
Checking the
picture currently
being recorded
To clear, press LIVE
CHECK.
To display, press
LIVE CHECK.
To stop recording,
press o.
(Playback and Live Check screen)
To stop Live Memory Playback,
Recording
stops
press o.
Live Memory Playback
picture
Recording
picture
NOTES:
Current playback point
(Live Memory Playback)
● Live Memory Playback could be performed approximately
30 seconds after recording has started.
● Although high-speed search up to approximately 30 seconds
before the current recording point is possible during Live Memory
Playback, once the current recording point is reached, the unit
resumes normal playback and maintains a delay of
approximately 30 seconds so that recording and playback can
continue.
Current recording position
(Recording point)
Recording start point
Playback
continues
Recording
continues
1 hour
0
30 min
● When using Live Memory Playback during timer recording, the
unit remains turned on and playback continues even after the
end of the recording.
Currently elapsed recording time
● When using Live Memory Playback during timer recording,
playback is automatically stopped just before recording starts,
and then recording starts when the time arrives for the next timer-
program.
● It is impossible to perform ITR even if you press R during Live
Memory Playback. Press o to display the program being
recorded, then perform ITR settings.
● Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
● When LIVE CHECK is pressed to display the picture currently
being recorded, the picture size may not be correct.
● Live Memory Playback cannot be performed while recording the
source from DV input.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
28
Live Memory Playback
You can playback the previous part of the channel you are
recording.
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
To watch from the recording start point
1 Press I during recording.
To watch from the point after reverse skipping a little during
recording
1 Press w during recording.
● Live Memory Playback could be performed approximately 30
seconds after recording has started.
● Pressing once skips back for approximately 7 seconds and
resumes playback.
NAVIGATION
Selection Keys (FGD E)
ENTER
Simultaneous Recording and Playback
You can playback other programs available in the Library
Database Navigation on the disc.
I
To watch other previously recorded programs during
recording
1 Press NAVIGATION to display the Library Database Navigation
w
ON SCREEN
screen.
2 Press selection keys to select AORIGINALB, then press
Live Memory Playback status can be checked by
pressing ON SCREEN to display the bar meter on the
superimpose display. The current status is
superimposed on the TV screen.
ENTER.
3 Press selection keys to select a desired program, then press
ENTER.
Bar meter display
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
29
G N
Buttons To Be Used During Live Memory Playback
● Each press of the button during playback advances the
playback speed in 4 steps in the forward direction.
● Pressing during pause mode advances playback at a slower
speed.
H o
● Pressing once stops Live Memory Playback and returns to the
screen on air.
● Pressing again stops the recording and returns to the screen on
air.
I W
● Pressing once pauses playback (still picture playback).
● Pressing repeatedly advances the still picture frame by frame.
J v
A NAVIGATION
It is useful when skipping over unwanted sections.
● Pressing once skips forward for approximately 30 seconds and
resumes playback.
B D
C E
● Pressing repeatedly skips forward continuously as many times
as pressed.
E T
D S
F O
G N
K w
I W
It is useful when watching sports programs, etc.
● Pressing once skips back for approximately 7 seconds and
resumes playback.
H o
J v
L LIVE CHECK
K w
● Pressing repeatedly skips back continuously as many times as
pressed.
L LIVE CHECK
You can check, for example, if the program you are recording
has already finished.
● Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
● Pressing successively clears the Live Check window and
displays only the picture currently being played back.
A NAVIGATION
Displays Library Database Navigation menu. You can choose a
title to play back.
B D
Pressing during pause mode reverses the still picture frame by
frame.
C E
Pressing during pause mode advances the still picture frame by
frame.
D S
● Pressing once skips back to the beginning of the program or
chapter being played back.
● Pressing down for 2 or more seconds during playback reverses
playback at a faster speed. Releasing the button resumes
normal playback.
Available only when paused
● Pressing down for 2 or more seconds reverses playback at a
slower speed.
E T
● Pressing once skips forward to the next program or chapter
being played back.
● Pressing down for 2 or more seconds during playback
advances playback at a faster speed. Releasing the button
resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds advances playback at a
slower speed.
F O
● Each press of the button during playback advances the
playback speed in 5 steps in the reverse direction.
● Pressing during pause mode reverses playback at a slower
speed.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
30
A Disc type.
B Select this for Repeat Playback. (A pg. 30)
D Select this for search function. (A pg. 31)
E Select this for time search function. (A pg. 32)
G Select this to switch picture source type. (A pg. 32)
H Current status area for the selected item.
I Select this for Program Playback. (A pg. 33)
J Select this for Random Playback. (A pg. 33)
K Select this to control the switching interval of the slide show.
(A pg. 33)
Using The On-screen Bar
The on-screen bar allows you to control various playback
functions. Some of the functions operated on Navigation Menu can
be controlled on the On-screen bar.
Be sure to clear Library Database Navigation screen by pressing
NAVIGATION.
NOTE:
Although examples of the on-screen bar are provided here only for
3 types of discs, the on-screen bar will be displayed for whichever
disc indicated in the left column.
Basic Operation On The On-screen Bar
Example: When selecting Picture Control function of DVD
0-9
During playback or while stopped
CANCEL
1 Press ON SCREEN twice to access the on-screen bar. The
item currently selected is highlighted and pointed by :.
NAVIGATION
SHARP
AUTO 1
DVD-VIDEO
Selection Keys (FGD E)
ENTER
2 Press selection keys to select “
”, then press ENTER. The
pop-up window appears under the selected item.
CLEAR(o)
SHARP
AUTO 1
DVD-VIDEO
ON SCREEN
3 Press selection keys to select the desired option, then press
ENTER.
DVD-VIDEO
CINEMA
AUTO 1
NORMAL
CINEMA
SHARP
SOFT
How To Access The On-screen Bar
1 Press ON SCREEN twice whenever a disc is loaded.
To clear the on-screen bar
Contents of the on-screen bar during playback
DVD VIDEO
Press ON SCREEN.
NOTE:
A
See the corresponding pages for details on each menu item.
DVD-VIDEO
SHARP
AUTO 1
Repeat Playback
B
C
D
E
F
G
Video CD/Super Video CD
A
You can repeat playback as you like according to the type of disc.
H
1 Press ON SCREEN twice to access the on-screen bar.
VIDEO-CD
CINEMA
2 Press selection keys to select AxB, then press ENTER. The
pop-up window appears under the selected item.
B
C
D
E
I
J
F
DVD-VIDEO
CINEMA
AUTO 1
OFF
JPEG disc
TITLE REPEAT
CHAPTER REPEAT
A
3 Press selection keys repeatedly to select the desired Repeat
mode, then press ENTER.
JPEG
10 sec
B
D
K
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
31
DVD-RAM/RW/R
● The point B must be set at least 3 seconds after the point A.
● When playing back a DVD, A-B Repeat Playback is possible only
within the same title.
● AA-B xB cannot be selected during Program and Random
Playback.
● AA-B xB cannot be selected while stopped.
OFF:
Repeat playback is not performed.
ALL REPEAT:
The whole disc is played back repeatedly.
TITLE REPEAT:
The current title is played back repeatedly.
Locating The Beginning Of A Desired Selection
DVD VIDEO
OFF:
Repeat playback is not performed.
You can locate the beginning of a title, chapter, group or track.
During playback or while stopped
TITLE REPEAT:
The current title is played back repeatedly.
1 Press ON SCREEN twice to access the on-screen bar.
CHAPTER REPEAT:
The current chapter is played back repeatedly.
2 Press selection keys to select A9B, then press ENTER.
Audio CD/Video CD/SVCD/JPEG/MP3
CINEMA
AUTO 1
DVD-VIDEO
OFF:
Repeat playback is not performed.
TITLE SEARCH
CHAPTER SEARCH
ALL REPEAT:
The whole disc is played back repeatedly.
3 Press selection keys to select the desired option, then press
ENTER.
TRACK REPEAT*:
The current track is played back repeatedly.
* ATRACK REPEATB cannot be selected for JPEG discs.
● Skip this step for Video CD/SVCD and Audio CD.
NOTE:
Settings that are selectable during playback and stop mode differ
depending on the type of disc and search used.
To clear the on-screen bar
Press ON SCREEN.
4 Press the number keys to enter the desired title or chapter
To cancel Repeat Playback
Repeat the above procedure from step 1, select AOFFB in step 3,
then press ENTER.
number, then press ENTER.
● Playback starts from the selected section.
NOTES:
DVD-VIDEO
CINEMA
AUTO 1
● Repeat Playback is not possible for a Video CD/SVCD with PBC
function.
TITLE
1 2
ENTER
● Repeat Playback may not work properly depending on the type of
the disc being used.
Examples:
A To select track 5, press the number key A5B.
B To select track 15, press the number keys A1B and A5B.
C To select track 25, press the number keys A2B and A5B.
A-B Repeat Playback
If you have specified a wrong number
Press CLEAR(o) or CANCEL on the remote control and re-enter
again.
You can repeat the desired part.
To clear the on-screen bar
Press ON SCREEN.
During Playback
1 Press ON SCREEN twice to access the on-screen bar.
2 Press selection keys to select AA-B xB.
NOTES:
● When A7B is displayed on the TV screen in step 4, the chapter
you have selected is not contained in the disc, or chapter search
does not work on the disc.
3 Press ENTER at the beginning of the desired part you want to
repeat (point A). The elapsed playing time of the point A
appears.
● Before you press ENTER, playback may start automatically when
you enter the section’s number depending on the disc.
● This function is not possible for a Video CD/SVCD with PBC
function.
DVD-VIDEO
CINEMA
AUTO 1
A
0:16:58
B
4 Press ENTER at the end of the desired part you want to repeat
(point B). The elapsed playing time of the point B appears.
● The selected part of the disc (between point A and B) is played
repeatedly.
DVD-VIDEO
CINEMA
AUTO 1
A
0:16:58
B
0:17:45
To clear the on-screen bar
Press ON SCREEN.
To cancel A-B Repeat Playback
Press selection keys to select AA-B xB, then press ENTER.
NOTES:
● A-B Repeat Playback may not work properly depending on the
type of disc being used.
● The subtitles recorded around the A-B point may not appear.
● When the end of the item is reached before the end point is set,
the on-screen bar disappears from the TV screen. In such a
case, repeat the procedure from step 1.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
32
Adjusting The Picture Quality
You can obtain optimal picture quality by selecting an appropriate
picture mode.
0-9
1 Press ON SCREEN twice to access the on-screen bar.
2 Press selection keys to select “
”, then press ENTER. The
CANCEL
pop-up window appears under the selected item.
DVD-VIDEO
CINEMA
AUTO 1
ENTER
Selection Keys (FGD E)
I
NORMAL
CINEMA
SHARP
SOFT
S
T
3 Press selection keys to select the desired option, then press
CLEAR(o)
ENTER.
ON SCREEN
NORMAL:
Normally select this.
CINEMA:
Suitable for a movie disc, etc.
SHARP:
Clearer, sharper-edged picture when viewing images with lots
of flat, same-colored surfaces such as cartoons.
Time Search
SOFT:
Select this option when too much noise appears.
To clear the on-screen bar
Press ON SCREEN.
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a program (DVD-RAM,
DVD-R, DVD-RW and DVD VIDEO) or a disc (Video CD/SVCD
and Audio CD).
Setting The Progressive Mode
1 Press ON SCREEN twice to access the on-screen bar.
2 Press selection keys to select Aj9B, then press ENTER. The
You can obtain optimal picture quality by selecting whether the
content on the disc is processed by field (video source) or by frame
(film source).
pop-up window appears under the selected item.
DVD-VIDEO
CINEMA
AUTO 1
1 Set the unit to the progressive scan mode. (A pg. 60)
2 Press ON SCREEN twice to access the on-screen bar.
TIME
:
:
ENTER
3 Press the number keys to enter the desired title or chapter
3 Press selection keys to select “
”, then press ENTER. The
number, then press ENTER. Playback starts from the specified
pop-up window appears under the selected item.
time.
Example:
DVD-VIDEO
SHARP
AUTO 2
To play back from a point 12 (minutes): 50 (seconds) elapsed.
AUTO 1
AUTO 2
FILM
TIME
TIME
Press 2
Press 0
Press 1
Press 5
VIDEO
TIME
TIME
TIME
4 Press selection keys to select the desired option, then press
ENTER.
AUTO 1:
If you have specified a wrong number
This mode automatically detects film and video content for
progressive playback. When film content is found, flag
detection is used to invoke playback of film data in full screen.
When video content is found, pictures from multiple fields are
used to detect sections with movement, and then this
movement undergoes advanced image processing for output of
sharp, detailed progressive images without any reduction in
image quality where movement occurs. Normally, operation in
this mode is recommended.
Press CLEAR(o) or CANCEL on the remote control and re-enter
again.
To clear the on-screen bar
Press ON SCREEN.
NOTES:
● When A7B is displayed on the TV screen in step 3, you have
selected a point that exceeds the recording time of the disc.
● Some DVD VIDEO discs do not contain time information, and it is
not possible to use the Time Search function. In such cases, A7B
is displayed on the TV screen as well.
AUTO 2:
Only the processing of sections with movement differs from
AAUTO 1B.
● This function is not possible for a Video CD/SVCD with PBC
function.
For video contents, the sections with movement are detected
and the pictures are corrected by the filtering process for
motion pictures.
FILM:
Suitable for playing back a progressive scanned film source disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
33
VIDEO:
Random Playback
Suitable for playing back a video source disc. The outlines on
the played back pictures will be soft.
To clear the on-screen bar
Press ON SCREEN.
You can play back all the tracks on the disc in random order.
While stopped
Program Playback
1 Press ON SCREEN twice to access the on-screen bar.
2 Press selection keys to select ARNDB, then press ENTER.
Playback starts in random order.
VIDEO-CD
RANDOM
You can program up to 30 tracks (Video CD/SVCD or Audio CD) to
play back in the desired order.
While stopped
To clear the on-screen bar
1 Press ON SCREEN twice to access the on-screen bar.
Press ON SCREEN.
2 Press selection keys to select APRGMB, then press ENTER.
To cancel Random Playback
Perform steps 1 and 2.
The program table appears under on-screen bar.
3 Press the number keys to enter the track numbers in the
NOTE:
desired order.
The same track will not be played back more than once during
Random Playback.
VIDEO-CD
PROGRAM
Select The Switching Interval Of The Slide Show
USE [0-9] KEYS TO SELECT TRACK
You can control the switching interval of the slide show.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press selection keys to select “
”, then press ENTER. The
pop-up window appears under the selected item.
Program Total Time
JPEG
10 sec
Examples:
5 sec
A To select track 5, press the number key A5B and ENTER.
B To select track 15, press the number keys A1B and A5B.
C To select track 25, press the number keys A2B and A5B.
10 sec
15 sec
20 sec
25 sec
30 sec
If you have specified a wrong selection
Press CANCEL. The last selection is erased.
Or press CLEAR(o). The whole selection is erased.
3 Press selection keys to select the desired option, then press
4 Press I. Playback starts in the programmed order.
● When all of the programmed tracks have been played back,
Program Playback stops, but the programmed information
remains.
● To add tracks to the end of the program, perform steps 1 to 3.
● During Program Playback, pressing T skips to the next track
of the program. Pressing S returns to the beginning of the
current track.
ENTER.
● Each time you press selection keys, the interval changes as
follows:
5 sec Y 10 sec Y 15 sec Y 20 sec Y 25 sec Y 30 sec Y
(Back to the beginning)
To clear the on-screen bar
Press ON SCREEN.
NOTE:
To clear the on-screen bar and the contents of the program
Press ON SCREEN.
JPEG files are played back as a slide show. It may take more time
to display an image with larger file size.
To cancel Program Playback
Press selection keys to select APRGMB, then press ENTER.
NOTE:
Program Playback is not possible depending on the type of disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
34
NOTES:
● It is recommended to format a DVD-RAM disc before use if you
use the disc on this unit for the first time. (A pg. 63)
● When using a brand-new DVD-RW disc, format the disc either in
Basic Recording
back on other DVD players. Perform “Finalize A Disc” (A pg. 64).
● You can record up to 99 programs and 99 play lists on each disc.
● Some programs can only be recorded one time.
● When recording is started, an index of the first part of recording is
automatically recorded. (A pg. 43) To delete the index, refer to
page 48.
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
ATTENTION:
It is not possible to record programs on a DVD-R/RW disc which
has already been finalized.
● Recording sometimes may stop or cannot be performed even if
there is enough available capacity remaining on the disc.
CH +/–
Recording Mode
MPEG 2 format is used as recording format. As a guide for picture
quality, the “bps” unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
RAM/RW
R o
The recording modes for a 4.7 GB disc are set as follows:
Recording mode
Recording amount
(approx.)
Maximum recording
time (approx.)
0-9
CH +/–
XP
SP
LP
EP
10 Mbps
5 Mbps
1 hour
2 hours
2.5 Mbps
1.6 Mbps
4 hours
ENTER
E
6 hours
D
R
60-360
(A pg. 36)
1 - 6 hours
I
The amount varies
depending on the
selected time.
FR
420
480
7 hours
8 hours
W
o
REC MODE
●
For details on FR mode, refer to “Free Rate Function” (
A
pg. 36).
1 Load a recordable disc.
● For details, refer to “Placing A Disc” (A pg. 10).
2 Press CH +/– or the number keys to select the channel you
wish to record.
3 Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes
as follows:
XP N SP N LP NEP N FR (60-360*, 420, 480) N (Back to the
beginning)
* The value is selectable from 1 to 6 hours in 5 minutes interval by
pressing D E repeatedly after selecting AFR60-FR360B. To change the
value in 30 minutes interval, press and hold D E.
● For details on the recording mode, see the right column.
4 Press R on the unit to start recording. Or while holding R, press
I on the remote control.
5 Press W to pause recording.
● To resume recording, press I.
6 Press o to stop recording.
● It takes about 10 seconds to end the writing session when you
stop recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
35
Instant Timer Recording (ITR)
It is possible to set the recording time during recording. Upon
completing recording, the unit stops and shut off automatically.
Recording Features
● Turn on the unit.
1 Press R on the unit to start RetroActive Recording.
● Turn on the TV and select an input mode such as EXT1.
2 Press R again to engage the ITR mode.
● A0:30B is displayed on the front display panel.
R
3 If you want to record for more than 30 minutes, press R to
extend the time. Each press extends recording time by
30 minutes.
RAM/RW
Normal recording N 0:30 N 1:00 ... N Maximum disc
remaining time N(Back to the beginning)
NOTES:
● Perform ITR using the R button on the unit.
● The maximum recording time changes depending on the disc
remaining time.
Watch Another Program While Recording On The Unit
While recording is going on, you can watch another program on
the TV. It does not interfere with recording.
1 Turn on the TV.
2 Select the desired channel to watch on TV using your TV’s
remote control.
Elapsed Recording Time And Disc Remaining Time
Indication
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time N Disc remaining time N Clock N (Back
to the beginning)
DISPLAY
REMAIN
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of
disc remaining times for all recording modes appears on the TV
screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS ON DVD DECK
EN
36
Free Rate Function
Second Audio Recording
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set A2ND
AUDIO RECORDB to AONB. (A pg. 59)
To record the entire program, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the program to be recorded and either the remaining
480 minutes when using 4.7 GB blank media disc).
NOTE:
When the channel is changed on the unit;
● The AMONOB indicator appears on the screen for about 5
seconds if the program is a monaural broadcast.
● The ASTEREOB indicator appears on the screen for about 5
seconds if the program is a stereo broadcast.
● Both ASTEREOB and ASAPB indicators appear when a stereo
program is accompanied by SAP sound.
8 To record the entire program within the actual remaining
disc space
● Note that this function is available only for timer programming
recording (A pg. 37, 38).
recording time
Select AFR60-FR360B, AFR420B or AFR480B in a recording mode
selection procedure. (A pg. 34)
● Both AMONOB and ASAPB indicators appear when the main audio
on the monaural broadcast is accompanied by SAP sound.
8 To record a 25 min. long daily program five times just on
the same DVD disc for example
Perform “VCR Plus+ Timer Programming” (A pg. 37) procedure.
Be sure to set the recording mode to AFR125B and set Weekly/
Daily Rec Function to AMON-FRIB in step 6 to fit the total recording
time to the whole disc space.
A: 1st
B: 2nd
Blank
C: 3rd
D: 4th
E: 5th
When the same program is recorded in SP mode instead of in
AFR125B, the 5th program cannot be recorded.
A: 1st
B: 2nd
C: 3rd
Blank
D: 4th
E: Blank (20 min.)
NOTES:
● You can program this unit to timer record, regardless of the disc
remaining time. If the disc remaining time is not enough, it is not
possible to record until the end of the timer program. To avoid
this, confirm the disc remaining time before setting timer
programming.
(Example) If you programmed to timer record for 60 minutes in
SP mode on a 120 minutes disc, the disc remaining time would
be 30 minutes in XP mode, 60 minutes in SP mode, 120 minutes
in LP mode, 180 minutes in EP mode, and 240 minutes in FR480
mode. Timer recording will not complete beyond these remaining
times.
● The maximum recording time of FR (JUST) mode is the same as
the recording time of FR480 mode. When timer programming a
long program in FR (JUST) mode on a disc whose remaining
time is short, it is recommended to check the disc remaining time
in FR480 mode to see if the remaining time is enough for the
program.
● Even if more than one program are timer programmed in FR
(JUST) mode, only the first one is recorded.
● In order to ensure that the recording fits on the disc, this feature
may leave a slight non-recorded section at the end of the disc.
● There may be some noise and sound disturbance at the point on
the disc where the unit switches the mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING
EN
37
5 Press selection keys to
VCR Plus+ PRGM
PLUSCODE NO.
VCR Plus+ Timer Programming
1
2
3
4
5
6
7
8
START
STOP
CH
ENTER.
● “Daily/Weekly Recording
Function” (A pg. 37)
● “Recording Mode”
DAILY/WEEKLY
REC MODE
NAME
You can program this unit to timer record as many as 8 programs.
With the VCR Plus+ system, timer programming is greatly
simplified because each TV program has a corresponding code
number which your unit is able to recognize.
XP
EXIT
OK
SET TIMER PROGRAMING WITH [CURSORS]
SELECT
PROG
You can use the remote control to enter the PlusCode number.
● “Modify Title Name” (A pg. 46)
● Turn on the unit.
7 Press ENTER to access the Program Confirmation screen.
● Turn on the TV and select an input mode such as EXT1.
● Make sure that the unit’s built-in clock is set properly.
8 Press ENTER to complete the timer programming.
● To program another timer, repeat steps 2 - 8.
● If APROGRAM OVERLAPPEDB appears on the TV screen, see
“When Programs Overlap Each Other” (A pg. 41).
9 Press TIMERj to engage the unit's timer mode.
● The unit turns off automatically and j appears on the front
display panel.
0-9
IMPORTANT:
CANCEL
If you have moved to a different area or if a broadcasting
station’s channel number has been changed, the wrong channel
number will be displayed on the VCR Plus+ program screen in
step 4. When this happens, set the correct Guide Channel
number for that station.
VCR Plus+
TIMERj
Selection Keys (FGD E)
ENTER
RETURN
● There may be cases that the “VCR Plus+ Timer Programming”
function prolongs the stop time of the programming.
● When two successive programs are recorded with the “VCR
Plus+ Timer Programming” function, the ending of the first
program or the beginning of the second program may not be
recorded.
CLEAR(o)
● If the copy limited program is received during timer recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Daily/Weekly Recording Function
You can record programs with one of the following weekly/daily
timer settings.
1 Load a recordable disc.
● For details, refer to “Placing A Disc” (A pg. 10).
2 Press VCR Plus+ to
VCR Plus+ PRGM
WEEKLY
MON-FRI
Select to record a weekly program.
Select to record a daily program from Monday
through Friday.
Select to record a daily program from Monday
through Saturday.
Select to record a daily program from Sunday
through Saturday.
display the AVCR Plus+
PLUSCODE NO. 1 2 3 4
PRGMB screen.
DATE
START
STOP
CH
3 Press the number keys
MON-SAT
SUN-SAT
to enter the
APLUSCODE NO.B of a
program you wish to
record, then press
ENTER.
DAILY/WEEKLY
REC MODE
NAME
SP
1
4
7
2
5
8
0
3
6
9
OK
ENTER VCR PLUS+ CODE WITH [0 - 9] KEYS
THEN PRESS [ENTER]
● If you have made a
mistake, press CANCEL and input the correct number before
you press ENTER.
● To clear all entered numbers at a time, press CLEAR(o).
● If the number you entered is invalid, APLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRYB appears on the TV
screen. Input a valid APLUSCODE NO.B.
● If AGUIDE PROGRAM IS NOT SET SELECT CHANNEL YOU
WANT TO RECORDB appears on the TV screen, set Guide
Channel numbers manually.
● When APROGRAM FULL DELETE UNWANTED TIMER
PROGRAMB appears on the TV screen, you need to cancel
some of the reserved programs.
4 The APLUSCODE NO.B you entered and the matching timer
recording information are displayed on the TV screen. Check
the program data.
● To cancel this setting, press RETURN.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed. If not, see “Changing VCR Plus+ Setting” (A pg. 62)
and set the Guide Channel number correctly.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING
EN
38
6 Press selection keys to set the desired stop time (ASTOPB),
then press E.
● Each press of F G increases/decreases the stop time in
1 minute interval.
Manual Timer Programming
● To increase/decrease the stop time in 30 minutes interval,
press and hold F G.
You can program this unit to timer record as many as 8 programs
up to 30 days in advance. If you do not know the PlusCode number
for the program you wish to record, use the following procedure to
set your unit to timer record the program.
7 Press selection keys to set the desired channel (ACHB), then
press E.
8 Set the other recording options as required.
● Refer to step 6 in “VCR Plus+ Timer Programming” (A pg. 37).
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
● Make sure that the unit’s built-in clock is set properly.
9 Press ENTER to access the Program Confirmation screen.
10Press ENTER to complete the timer programming.
● To program another timer, repeat steps 2 - 10.
11Press TIMERj to engage the unit’s timer mode.
● The unit turns off automatically and j appears on the front
display panel.
● To disengage the timer mode, press TIMERj again.
NOTES:
● When two successive programs are recorded with the “Manual
Timer Programming” function, the ending of the first program or
the beginning of the second program may not be recorded.
● If the copy limited program is received during timer recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
TIMERj
PROG
Selection Keys (FGD E)
ENTER
Cable Box or DBS Receiver Users
To record a satellite broadcast using Manual Timer
Programming:
A Perform Manual Timer Programming.
● Set the channel to the external input (AL-1B or AF-1B)
connected to the cable box or DBS receiver.
B Set the cable box or DBS receiver to the appropriate channel
for recording.
● Leave the cable box or DBS receiver’s power on.
1 Load a recordable disc.
● For details, refer to “Placing A Disc” (A pg. 10).
2 Press PROG to display
PROGRAM CHECK
the APROGRAM
DATE
START
STOP
CH
44
DAILY/WEEKLY REC MODE
CHECKB screen.
05/07 SAT 7:00PM - 8:00PM
WEEKLY
SP
XP
LP
LP
10/07 THU 10:00PM - 10:30PM 10
11/07 FRI 08:00AM - 09:00AM 26
11/07 FRI 08:30AM - 09:30AM 33
● When APROGRAM FULL
DELETE UNWANTED
TIMER PROGRAMB
appears on the TV
++++++++++++++++++ NEW TIMER PROGRAM ++++++++++++++++++
screen, you need to
cancel some of the
reserved programs.
DISC TIMER PRGM
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
3 Press selection keys
repeatedly to select
ANEW TIMER
TIMER PROGRAM
DATE
10/07/03 THU
START
- - : - -
STOP
- - : - -
CH
- -
PROGRAMB, then press
ENTER.
DAILY/WEEKLY
REC MODE
SP
4 Press selection keys to
NAME
set the desired date
(ADATEB), then press E.
EXIT
CONFIRM
SELECT
SET TIMERPROGRAMING WITH [CURSORS]
THEN PRESS [ENTER]
5 Press selection keys to
set the desired start time
(ASTARTB), then press E.
PROG
● Each press of F G increases/decreases the start time in
1 minute interval.
● To increase/decrease the start time in 30 minutes interval,
press and hold F G.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING
EN
39
To Make The Disc For On-Disc Timer Programming
On-Disc Timer Programming
1 Press PROG to access
PROGRAM CHECK
the Program Check
DATE
START
STOP
CH
DAILY/WEEKLY REC MODE
screen.
++++++++++++++++++ NEW TIMER PROGRAM ++++++++++++++++++
2 Press selection keys to
select ADISC TIMER
PRGMB, then press
ENTER.
● When some programs
are recorded on the disc,
a caution message
appears. To backup the recorded programs, press ENTER, and
perform dubbing to other devices.
● When On-Disc Timer Programming has already been made on
the disc, press selection keys to select ANEW TIMER
PROGRAMB, then press ENTER.
On-Disc Timer Programming is a function used with discs that are
especially intended for a specific program. The disc is then
programmed for a program you always watch every day or every
week. Since older programs are automatically overwritten, a single
disc can be used without worrying about how much recording
capacity remains. You can program each disc to timer record as
many as 8 programs up to 30 days in advance.
DISC TIMER PRGM
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
● Make sure that the unit’s built-in clock is set properly.
● Turn on the TV and select an input mode such as EXT1.
● Load a DVD-RAM or DVD-RW (VR mode) disc for
programming.
3 Press selection keys to
DISC TIMER PRGM
set the desired date
(ADATEB), then press E.
ATTENTION:
DATE
START
STOP
CH
- -
● On-Disc Timer Programming is possible only with the disc for
On-Disc Timer Programming.
4 Press selection keys to
set the desired start time
(ASTARTB), then press E.
● Each press of F G
increases/decreases the
start time in 1-minute
interval.
10/07/03 THU - - : - - - -
- - : - - - -
DAILY/WEEKLY
WEEKLY
REC MODE
SP
● If data is recorded on a disc for On-Disc Timer Programming
using a unit from another manufacturer, On-Disc Timer
Programming may not function properly.
NAME
EXIT
CONFIRM
SELECT
SET TIMERPROGRAMING WITH [CURSORS]
THEN PRESS [ENTER]
PROG
● To increase/decrease the start time in 30-minutes interval,
press and hold F G.
5 Press selection keys to set the desired stop time (ASTOPB),
DVD A
then press E.
● Each press of F G increases/decreases the stop time in 1-
minute interval.
press and hold F G.
6 Press selection keys to set the desired channel (ACHB), then
press E.
PROG
Selection Keys (FGD E)
ENTER
8 Set the other recording
DISC TIMER PRGM
options as required.
● “Recording Mode”
(A pg. 34)
● “Modify Title Name”
(A pg. 46)
DATE
START
STOP
- - : - - - -
CH
- -
10/07/03 THU - - : - - - -
DAILY/WEEKLY
WEEKLY
REC MODE
SP
NAME
9 Press ENTER to access
the Program
EXIT
CONFIRM
SELECT
SET TIMERPROGRAMING WITH [CURSORS]
THEN PRESS [ENTER]
Confirmation screen.
PROG
10Press ENTER to
complete the timer programming.
● To program another timer using “To Make The Disc For On-
Disc Timer Programming”, repeat steps 1 - 10.
11Press DVD A to turn off the power.
●
is displayed on the front display panel.
● To disengage the timer mode, press DVD A again.
Cable Box or DBS Receiver Users
To timer record a satellite broadcast using On-Disc Timer
Programming:
A Perform On-Disc Timer Programming.
● Set the channel to the external input (AL-1B or AF-1B)
connected to the cable box or DBS receiver.
B Set the cable box or DBS receiver to the appropriate channel
for recording.
● Leave the cable box or DBS receiver’s power on.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING
EN
40
To Timer Record The Program With The Programmed
Disc
How Discs Are Overwritten
(Example 1)
To record a 1 hour serial drama every Friday in SP mode
1 Load a programmed disc.
2 Press DVD A to turn off the power.
●
appears on the front display panel, and the unit enters
into timer standby mode.
● To disengage the timer mode, press DVD A again.
1st
2nd
1st
Blank
NOTES:
● On-Disc Timer Programming is not possible on a DVD-R or
DVD-RW (Video mode) disc.
● The information of a program recorded with On-Disc Timer
Programming is not stored in the library.
● The play list is not created for the programs recorded with On-
Disc Timer Programming.
● Programs recorded with On-Disc Timer Programming cannot be
edited or protected.
2nd
3rd
4th
3rd
● On-Disc Timer Programmed discs cannot be used for other
recordings other than On-Disc Timer Programming.
● On-Disc Timer Programmed discs cannot be used on units from
other manufacturers.
● The beginning of a program may not be recorded. In addition, if
the 1st program’s recording stop time and the 2nd program’s
recording start time is the same, the ending of the 1st program
may not be recorded.
● If there is a power outage while recording, the recordings when
the power outage occurs are not guaranteed.
The first program is
overwritten by the third.
The second program is
overwritten by the
fourth.
(Example 2)
To record a 15 minutes serial drama every morning in XP
mode
4th
12/6
1st
12/3
8th
12/10
5th
12/7
3rd
12/5
2nd
12/4
7th
12/9
6th
12/8
(Example 3)
To record a 90 minutes serial drama every Sunday in SP
mode
2nd
Blank
Blank
1st
3rd
Areas treated as blank
cannot be played back
even if they contain
recorded material.
Blank
NOTE:
On-Disc Timer Programming may not always work as these
examples.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING
EN
41
When Programs Overlap Each Other
If APROGRAM OVERLAPPEDB appears, you have another
program overlapping the program you have just made. Press
Check, Cancel And Change Programs
PROG. Program Check screen appears and conflicting programs
will be highlighted in pink.
Example: Program 3 (you
have just made) and
PROGRAM CHECK
DVD A
DATE
START
STOP
CH
44
DAILY/WEEKLY REC MODE
Program 4 overlap each
other.
05/07 SAT 7:00PM - 8:00PM
WEEKLY
SP
XP
LP
LP
10/07 THU 10:00PM - 10:30PM 10
11/07 FRI 08:00AM - 09:00AM 26
11/07 FRI 08:30AM - 09:30AM 33
++++++++++++++++++ NEW TIMER PROGRAM ++++++++++++++++++
1 Confirm the overlapping
programs.
CANCEL
TIMERj
REC LINK
NOTES:
DISC TIMER PRGM
PROG
EXIT
OK
● If you do not mind this
overlap, press PROG to
finish the timer program
setting.
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
Selection Keys (FGD E)
ENTER
● Recording is performed according to the order as displayed on
the Program Check screen. The timer program that follows will
not be performed correctly.
● If no changes are made for approximately 1 minute, the unit will
automatically return to the normal screen.
CLEAR(o)
To cancel the program
Press selection keys to select a program to be canceled, then
press CLEAR(o).
● ATHE TIMER PROGRAMING SETTING WAS CANCELLEDB
appears on the TV screen for about 5 seconds, then the normal
screen resumes.
To change the program
1 Disengage the timer mode.
Press selection keys to select a program to be changed, then
press ENTER.
● When
A.
lights up on the front display panel, press DVD
● Change each setting as required.
● When j lights up on the front display panel, press TIMERj,
and press DVD A after j lights off.
● When AR-LKB lights up on the front display panel, press
REC LINK.
2 Press ENTER to exit the Program screen.
3 Press TIMERj to enter into timer standby mode.
2 Press PROG to access the Program Check screen.
● To return to the previous screen after you check the program,
press PROG again.
NOTE:
When any overlaps remain after deletion and modification of
programs, Program Overlap list remains showing the conflicting
programs. In such a case, repeat the procedure above until the
conflict is solved.
To cancel the program
3 Press selection keys to select a program to be changed, then
press ENTER.
4 Change the settings of the desired recording options as
required.
● Refer to steps 4 - 10 in “Manual Timer Programming”
(A pg. 38).
5 Press PROG to exit the program screen.
6 Set the unit to timer standby mode.
For VCR Plus+ or Manual Timer Programming
● Press TIMERj so that j lights up on the front display panel.
For On-Disc Timer Programming
● Press DVD A so that
panel.
lights up on the front display
For Automatic Satellite Program Recording
● Press REC LINK for 2 or more seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING
EN
42
● Make sure the DBS receiver is connected to the unit’s
[S-VIDEO/VIDEO/AUDIO INPUT L-1] connectors.
● Program the timer on the DBS receiver.
Automatic Satellite Program Recording
This function allows you to automatically record a satellite program
which is timer programmed on your external DBS receiver.
Connect a DBS receiver to the unit’s [S-VIDEO/VIDEO/AUDIO
INPUT L-1] connectors and program the timer on the DBS
receiver. The unit starts or stops recording by the signals input
from the DBS receiver. After recording, the unit’s power shuts off
automatically.
1 Press REC MODE repeatedly to set the recording mode.
2 Press and hold REC LINK for about 2 seconds to engage the
Automatic Satellite Program Recording mode. AVB and AR-LKB
NOTES:
● To disengage the Automatic Satellite Program Recording mode,
press REC LINK.
ATTENTION:
● Be sure not to turn on the DBS receiver before the program is
executed. Otherwise, the unit will start recording when the DBS
receiver’s power is turned on.
Satellite Program Recording mode.
● In step 2, if AVB blinks quickly on the front display panel even
though your DBS receiver’s power is off, Automatic Satellite
Program Recording will not work properly with that DBS
receiver*. If this is the case, perform “Manual Timer
Programming” (A pg. 38) to timer record a satellite program.
* Some DBS receivers output signals even if the power is off. Automatic
Satellite Program Recording is not possible with those DBS receivers.
● AVB blinks on the front display panel while Automatic Satellite
Program Recording is in progress.
● If you have connected another appliance other than a DBS
receiver to the [S-VIDEO/VIDEO/AUDIO INPUT L-1]
connectors, be sure not to engage the Automatic Satellite
Program Recording mode. Otherwise, the unit will start
recording when the connected appliance’s power is turned on.
● Automatic Satellite Program Recording and timer recording
cannot be done at the same time.
● For timer programming of the DBS receiver, refer to the
instruction manual of the DBS receiver.
● Automatic Satellite Program Recording is not possible if your
DBS receiver does not have a timer.
● Pressing the unit’s A button while Automatic Satellite Program
Recording is in progress turns off the unit’s power and
disengages the Automatic Satellite Program Recording mode.
● If there are more than one satellite programs you wish to record
with Automatic Satellite Program Recording, it is not possible to
set different recording modes for each program.
● Depending on the type of DBS receiver, the unit may not record a
slight portion of the beginning of the program or may record
slightly longer than the actual length of the program.
● If you engage the Automatic Satellite Program Recording mode
when the DBS receiver’s power is on, the unit will not start
Automatic Satellite Program Recording even though AVB blinks on
the front display panel. When the DBS receiver shuts off once
and is turned back on again, the unit starts recording.
● You can also record a program from your cable system in the
same way if the system has a timer.
REC LINK
● When the Automatic Satellite Program Recording mode is
engaged, or the unit’s power is turned off after Automatic Satellite
Program Recording is finished, the unit will not enter the timer
mode even though AAUTO TIMERB is set to AONB (A pg. 60).
REC MODE
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
43
Using Library Database Navigation system, you can easily modify
registered information, edit the title or play list, as well as search
for the beginning of each title.
Library Database Navigation
About registration of information
The following information is automatically registered for each title
when ordinary recording or timer recording is performed, then
stored in an area specified on the unit.
● index* (reduced pictures to show program titles)
● program title*
● category*
● date and time
● channel
● recording mode
The Library Database Navigation enables you to search and select
the desired titles recorded very easily.
You can record up to 99 titles on a disc.
Each time a title is recorded, the information of the title is
registered for the Library Database Navigation automatically.
So, you can confirm the information of the titles recorded with the
Library Database Navigation screen. And, you can also select one
of the titles recorded using the Library Database Navigation.
The following screen appears as the Library Database Navigation
screen when you press NAVIGATION. You can move the arrow to
select the desired position on the screen by pressing the selection
keys on the remote control.
● length of recording time
The items marked with an asterisk (*) can be easily modified and
registered again after recording by using Library Database
Navigation system.
The limitations of registration
A
B
CD E
You can register information up to 99 programs in a single DVD.
When the amount of information is at the limits of registration, you
cannot record new titles any more. In this case, you need to delete
old titles to register new ones. (A pg. 44)
ORIGINAL
PLAY LIST
LIBRARY
0001
REMAIN TIME 87min(SP) 1/6
1
2
3
4
NOTES:
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. As only display
for library appears, press TOP MENU to display the following
screen to select the desired title.
DANCE
DANCE CURNIV
[OTHERS]
28/07/03 MON 10:00 - 11:00
CH7 SP
60min
MODIFY
OK
SELECT
DELETE
NAVIGATION
EDITING
PROTECT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
CONTENTS MENU
PREV
81 Sister Princess ED2 14/11 0:55 PR12<HDD MN26
82 GALAXY ANGLE A#04 OP 06/10 9:30 PR12<HDD
83 GALAXY ANGLE A#04 ED 06/10 9:30 PR12<HDD
84 FISHING WORLD OP 22/12 20:00 PR3
85 FISHING WORLD ED 22/12 20:00 PR3
86 RALLY CAR OP 10/04 0:30 PR3
16.11.2002
07.10.2002
07.10.2002
22.12.2002
22.12.2002
04.10.2002
04.10.2002
02.05.2002
02.05.2002
26.09.2002
F
G
H
A INDEX
(Thumbnail of each program)
B Menu index
ORIGINAL (A pg. 44)
PLAY LIST (A pg. 47)
LIBRARY (A pg. 51)
C Remaining time
87 RALLY CAR ED 10/04 0:30 PR3
88 Chobits #04 OP 02/05 PR10
89 Chobits #04 ED 02/05 PR10
90 Chobits #25 ED 26/09 PR10 MN32 LPCM
NEXT
(Based on the recording speed currently selected)
D Current/Total number of program(s)
E Icons
F Recording information for the program indicated by the arrow
G Guidance for operations
● Sound of received channel may be interrupted while the Library
Database Navigation screen is displayed.
● You cannot perform timer recording during editing of thumbnail
images or play lists by pressing NAVIGATION. Press
NAVIGATION to clear the editing screen before performing timer
recording.
H Operational commands
The Icons and their meanings
This program is write-protected.
This program has stereo sounds.
This program was recorded with timer
recording.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
44
Protect Title (DVD-RAM & DVD-RW (VR mode) only)
You can protect titles to prevent accidental erasure of the
important titles.
Basic Operation Of Original Information
You can scan the beginning of the title easily and play back with
the Library Database Navigation.
1 Press NAVIGATION to display the Library Database Navigation
screen.
● Turn on the TV and select an input mode such as EXT1.
● Load a DVD disc to play back.
2 Press selection keys to select AORIGINALB, then press
ENTER.
3 Press selection keys to select a title you want to protect, then
press G.
4 Press selection keys to select “PROTECT”, then press
ENTER.
● “
” appears on the TV screen.
● To cancel the protection, select “PROTECT” again, then press
ENTER.
5 Press NAVIGATION to return to the normal screen.
NOTE:
MEMO
All the titles on a disc will be deleted once the disc is formatted
even if they are protected titles. (A pg. 63)
NAVIGATION
Selection Keys (FGD E)
ENTER
Delete Title
You cannot record any more with Library Database Navigation
once the registered titles on the disc reach 99 titles. Deleting
unnecessary titles after dubbing or other operations can increase
remaining time and available recording capacity. (For DVD-R
discs, although it is possible to delete recorded titles, available
recording capacity does not increase.) The deleted title cannot be
retrieved. Play lists and title information in the unit’s library are also
deleted.
I
CLEAR/o
1 Press NAVIGATION to display the Library Database Navigation
screen.
2 Press selection keys to select AORIGINALB, then press
ENTER.
Play Back Title
3 Press selection keys to select a title you want to delete, then
press G.
1 Press NAVIGATION to display the Library Database Navigation
4 Press selection keys to select ADELETEB, then press ENTER.
screen.
● The confirmation screen appears.
2 Press selection keys to select AORIGINALB, then press
5 Press selection keys to select AYESB, then press ENTER.
● To cancel the deletion, select ANOB, then press ENTER.
ENTER.
3 Press selection keys to
ORIGINAL
PLAY LIST
REMAIN TIME
LIBRARY
87min(SP)
6 Press NAVIGATION to return to the normal screen.
select the index (small
pictures) of the desired
title, then press ENTER
or I.
0001
1
2
3
4
DANCE
● With the arrow on
AORIGINALB, all titles will
be played back
according to the index
● All subsequent titles after
DANCE CURNIV
[OTHERS]
60min
PROTECT
28/07/03 MON 10:00 - 11:00
CH7 SP
MODIFY
OK
DELETE
NAVIGATION
EXIT
EDITING
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
the selected index will be played back in order.
● The unit stops when playback ends, and resumes to a
broadcast receiving screen.
● Press o to stop playback. If ARESUMEB is set to AONB or ADISC
RESUMEB (A pg. 60), playback starts from the point where
playback was previously stopped when I is pressed.
● When you want multiple titles to be played back in a determined
order, press selection keys to select the desired title, then
press MEMO. The numbers of the playback order appear on
the index. (Up to 30 titles.)
● When you want to correct the order, move the arrow to the
desired index and press MEMO. The number disappears and
the unit re-numbers the other titles automatically.
● When you want to cancel the order, press CLEAR(o).
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
45
Delete Unwanted Part Of The Title
(DVD-RAM & DVD-RW (VR mode) only)
You can delete unwanted part of a title.
1 Press NAVIGATION to
ORIGINAL
PLAY LIST
REMAIN TIME
LIBRARY
87min(SP)
display the Library
Database Navigation
screen.
0001
1
2
3
4
2 Press selection keys to
select AORIGINALB, then
press ENTER.
DANCE
DANCE CURNIV
[OTHERS]
60min
28/07/03 MON 10:00 - 11:00
CH7 SP
EDITING
MODIFY
OK
SELECT
DELETE
NAVIGATION
EXIT
PROTECT
3 Press selection keys to
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
select a title whose
unwanted part you want
to delete, then press G.
4 Press selection keys to select AEDITINGB, then press ENTER.
5 Press I to start
DELETE SCENE
IN
OUT
playback.
● Press O or N to find
the point where you want
the deletion to begin,
then press W.
A
0:00:29:24
-:--:--:--
IN
OUT
A
:
:
:
TOTAL TIME
TITLE 05 CHAPTER 01
TIME 0000:00:53 **
6 Confirm the arrow is on
AINB, then press ENTER.
● The edit-in time is
RETURN
OK
SELECT
PREVIEW
EXECUTE
CLEAR
NAVIGATION
EXIT
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
displayed on the left of
the AINB window.
7 Press I to resume playback.
● Press W to pause at the point where you want the deletion to
end.
8 Confirm the arrow is on AOUTB, then press ENTER.
9 Press selection keys to select APREVIEWB, then press ENTER
to preview the edited title.
To modify the points
A Press selection keys to select ACLEARB, then press ENTER.
● Press selection keys to select ARETURNB, then press ENTER
to return to the screen in step 4.
B Press selection keys to select AINB.
C Perform steps 5 - 9.
10Press selection keys to select AEXECUTEB, then press
ENTER.
● The confirmation screen appears.
11Press selection keys to select AYESB, then press ENTER.
● When you cancel the deletion, select ANOB, then press
ENTER.
12Press NAVIGATION to return to the normal screen.
NOTES:
● There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
● Available recording capacity may not match the deleted part after
deletion.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
46
Modify Title Name
Edit Original Information
1 Perform steps 1 - 4 of “Modify Index” (A pg. 46) before
continuing.
2
Press selection keys to
select AMODIFY NAMEB,
MODIFY INDEX MODIFY NAME
MODIFY CATEGORY
DANCE CURNIV
then press ENTER
.
DELETE
DELETE ALL
● Turn on the TV and select an input mode such as EXT1.
● Load a DVD disc to modify.
A
J
B
K
T
C
L
D
M
V
E
N
F
O
X
G
P
Y
H
Q
Z
I
1
4
7
2
5
8
3
6
9
!
"
'
#
(
$
)
%
3 Input a new title name.
● Press selection keys to
select the desired letter
or symbol, then press
ENTER.
● To erase the letter, press
selection keys to select
R
&
0
∗
S
U
W
+
-
DANCE CURNIV
28/07/03 MON 10:00 - 11:00
[OTHERS]
60min
ATTENTION:
CH7 SP
● It is not possible to modify discs recorded on DVD units from
other manufacturers.
RETURN
OK
SELECT
SAVE
NAVIGATION
EXIT
ENTER NAME WITH [0 - 9] KEYS
THEN SELECT “SAVE”
● You cannot perform timer recording during editing of index by
pressing NAVIGATION. Press NAVIGATION to clear the
editing screen before performing timer recording.
ADELETEB or ADELETE ALLB, then press ENTER.
● You can enter up to 64 letters.
● You can also use the number keys on the remote control to
input the letters. For example, pressing number key “2”
repeatedly changes the letter in the order of “A”, “B”, “C”, “a”,
“b”, “c” and “2”. The following buttons can also be used.
Number keys: To input alphabet, numbers and space.
D E buttons: To move the input position and insertion point.
o button: To correct the letters.
S/T buttons: To switch the character table.
0-9/A-Z
4 Press selection keys to select ASAVEB, then press ENTER.
● The new title name is registered.
5 Press selection keys to select ARETURNB, then press ENTER.
the modified name.
NAVIGATION
Selection Keys (FGD E)
ENTER
6 Press NAVIGATION to return to the normal screen.
I
N
W
O
Modify Category
1 Perform steps 1 - 4 of “Modify Index” (A pg. 46) before
o
continuing.
2 Press selection keys to
MODIFY INDEX
MODIFY NAME MODIFY CATEGORY
select AMODIFY
CATEGORYB, then
press ENTER.
MOVIES
SPORTS
EDUCATION
SHOPPING
MUSIC
DOCUMENTARY
HOBBY
DRAMA
NEWS
ANIMATION
WEATHER
ART
ENTERTAINMENT
OTHERS
3 Press selection keys to
select the desired
category, then press
ENTER.
DANCE CURNIV
[OTHERS]
60min
28/07/03 MON 10:00 - 11:00
RETURN
CH7 SP
Modify Index
OK
NAVIGATION
EXIT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
1 Press NAVIGATION to display the Library Database Navigation
4 Press selection keys to
select ARETURNB, then
press ENTER.
SELECT
screen.
2 Press selection keys to select AORIGINALB, then press
ENTER.
● Return to the Library Database Navigation screen to confirm
the modified category.
3 Press selection keys to select a title you want to modify, then
press G.
5 Press NAVIGATION to return to the normal screen.
4 Press selection keys to select AMODIFYB, then press ENTER.
5 Press selection keys to select AMODIFY INDEXB, then press
ENTER.
6 Press I to start
MODIFY INDEX MODIFY NAME MODIFYCATEGORY
playback. Press O or
N to search for the
REPLACE
picture from the title,
then press W.
00:05:00
00:00:21
7 Confirm the arrow is on
AREPLACEB, then press
ENTER.
● The new index appears
on the right window.
[OTHERS]
60min
28/07/03 MON 10:00 - 11:00
RETURN
CH7 SP
OK
NAVIGATION
EXIT
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
SELECT
8 Confirm the arrow is on ARETURNB, then press ENTER.
● You can confirm the new index.
9 Press NAVIGATION to return to the normal screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
47
5 Confirm the arrow is on
AINB, then press ENTER.
● The edit-in time is
CREATE
IN
OUT
Basic Operation Of Play List
Information
A
displayed on the left of
the AINB window.
0:00:29:24
-:--:--:--
IN
OUT
A
:
:
:
TOTAL TIME
6 Press I to resume
TITLE 05 CHAPTER 01
TIME 0000:00:53 **
playback.
RETURN
OK
PREVIEW
EXECUTE
CLEAR
● Press W to pause at the
point where you want the
created play list to end.
NAVIGATION
EXIT
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
SELECT
Play List
It is a collection of the scenes. A play list can be freely edited and
played back without ever changing any original recording data.
Using the random access of a disc (which allows video data to be
instantly read no matter where it is on the disc), a play list includes
information such as the timer counter for the playback start point
and end point, indexes for checking the contents of recorded data,
category information, and more. Playback according to a play list
you have created allows you to enjoy various combinations of
video images from a single title.
7 Confirm the arrow is on AOUTB, then press ENTER.
● The edit-out time is displayed on the left of the AOUTB window.
● The edit-out point must come after the edit-in point.
8 Press selection keys to select APREVIEWB, then press ENTER
to preview the play list.
● To cancel play list creation, press selection keys to select
ARETURNB, then press ENTER.
To modify the points
A Press selection keys to select ACLEARB, then press ENTER.
B Press selection keys to select AINB.
C Repeat steps 3 - 8.
● Turn on the TV and select an input mode such as EXT1.
● Load a DVD disc to modify.
9 Press selection keys to select AEXECUTEB, then press
ENTER. The play list is created.
ATTENTION:
It is not possible to modify discs recorded on DVD units from
other manufacturers.
10Press NAVIGATION to return to the normal screen.
NOTES:
● There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
● The title, index and category of the play list can be modified in the
same way as AORIGINALB. (A pg. 46)
● You can modify the play list that has just been created here by
adding, moving, or deleting unwanted parts to create a digest
edition, etc.
Play Back Play List
1 Press NAVIGATION to display the Library Database Navigation
NAVIGATION
screen.
Selection Keys (FGD E)
2 Press selection keys to select APLAY LISTB, then press
ENTER
ENTER.
I
3 Press selection keys to select a play list to be played back,
then press ENTER.
● The unit stops when playback ends, and resumes to a
broadcast receiving screen.
S
O
T
N
W
● When you want the multiple play lists to be played back
continuously, press MEMO after selecting the desired play lists.
The numbers of the playback order appear on the index. (Up to
30 titles)
Delete Play List
1 Press NAVIGATION to display the Library Database Navigation
Create Play List
1 Press NAVIGATION to
display the Library
Database Navigation
screen.
screen.
2 Press selection keys to select APLAY LISTB, then press
ENTER.
ORIGINAL
PLAY LIST
LIBRARY
0001
3 Press selection keys to
ORIGINAL
PLAY LIST
LIBRARY
1
2
3
4
select a play list you
want to delete, then
press G.
0001
1
2
3
4
2 Press selection keys to
select APLAY LISTB, then
press ENTER.
[OTHERS]
CREATE
4 Press selection keys to
select ADELETEB, then
press ENTER.
● The confirmation screen
appears.
28/07/03 MON
MODIFY
OK
DELETE
EDITING
[OTHERS]
CREATE
3 Press selection keys to
select ACREATEB, then
press ENTER.
28/07/03 MON
MODIFY
OK
NAVIGATION
EXIT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
DELETE
EDITING
SELECT
NAVIGATION
EXIT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
4 Press I to start playback.
5 Press selection keys to
● To move to other titles, press S or T.
select AYESB, then press ENTER.
● Press O or N to find the point where you want the created
play list to begin, then press W.
● To cancel the deletion, select ANOB, then press ENTER.
6 Press NAVIGATION to return to the normal screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
48
Modify Play List Name
Edit Play List Information
continuing.
2 Press selection keys to select AMODIFY NAMEB, then press
ENTER.
● Turn on the TV and select an input mode such as EXT1.
● Load a DVD disc to modify.
3 Input a new title name.
MODIFY INDEX MODIFY NAME MODIFY CATEGORY
See “Modify Title Name”
DANCE CURNIV
(A pg. 46).
DELETE
DELETE ALL
A
J
B
K
T
C
L
D
M
V
E
N
F
O
X
G
P
Y
H
Q
Z
I
1
4
7
2
5
8
3
6
9
!
"
'
#
(
$
)
%
4 Press selection keys to
select ASAVEB, then
press ENTER.
R
&
0
∗
ATTENTION:
S
U
W
+
-
It is not possible to modify discs recorded on DVD units from
other manufacturers.
DANCE CURNIV
28/07/03 MON 10:00 - 11:00
[OTHERS]
60min
CH7 SP
5 Press selection keys to
select ARETURNB, then
press ENTER.
RETURN
OK
SELECT
SAVE
NAVIGATION
EXIT
ENTER NAME WITH [0 - 9] KEYS
THEN SELECT “SAVE”
● Return to the Library
Database Navigation screen to confirm the modified name.
6 Press NAVIGATION to return to the normal screen.
Modify Category
1 Perform steps 1 - 4 of “Modify Index” (A pg. 48) before
continuing.
2 Press selection keys to select AMODIFY CATEGORYB, then
press ENTER.
NAVIGATION
Selection Keys (FGD E)
ENTER
3 Press selection keys to
MODIFY INDEX MODIFY NAME MODIFY CATEGORY
select the desired
MOVIES
SPORTS
EDUCATION
SHOPPING
MUSIC
DOCUMENTARY
HOBBY
DRAMA
NEWS
ENTERTAINMENT
ANIMATION
WEATHER
ART
category, then press
ENTER.
I
S
T
O
N
W
OTHERS
4 Press selection keys to
select ARETURNB, then
press ENTER.
● Return to the Library
Database Navigation
screen to confirm the
modified category.
DANCE CURNIV
[OTHERS]
60min
28/07/03 MON 10:00 - 11:00
RETURN
CH7 SP
OK
NAVIGATION
EXIT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
5 Press NAVIGATION to return to the normal screen.
Modify Index
1 Press NAVIGATION to display the Library Database Navigation
screen.
2 Press selection keys to select APLAY LISTB, then press
ENTER.
3 Press selection keys to select a play list you want to modify,
then press G.
4 Press selection keys to
ORIGINAL
PLAY LIST
REMAIN TIME
LIBRARY
87min(SP)
select AMODIFYB, then
press ENTER.
0001
1
2
3
4
5 Press selection keys to
select AMODIFY INDEXB,
then press ENTER.
DANCE
DANCE CURNIV
[OTHERS]
60min
28/07/03 MON 10:00 - 11:00
CH7 SP
EDITING
6 Press I to start
playback. Press O or
N to search for the
picture from the title,
then press W.
MODIFY
OK
SELECT
DELETE
NAVIGATION
EXIT
CREATE
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
7 Confirm the arrow is on
AREPLACEB, then press
ENTER.
● The new index appears
on the right window.
MODIFY INDEX MODIFY NAME MODIFY CATEGORY
REPLACE
00:05:00
00:00:21
8 Confirm the arrow is on
ARETURNB, then press
ENTER.
● You can confirm the new
index.
[OTHERS]
60min
28/07/03 MON 10:00 - 11:00
RETURN
CH7 SP
OK
NAVIGATION
EXIT
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
SELECT
9 Press NAVIGATION to return to the normal screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
49
Delete Scenes
Move Scenes
1 Press NAVIGATION to
display the Library
Database Navigation
screen.
1 Press NAVIGATION to
display the Library
Database Navigation
screen.
ORIGINAL
PLAY LIST
REMAIN TIME
LIBRARY
87min(SP)
ORIGINAL
PLAY LIST
LIBRARY
0001
0001
REMAIN TIME
87min(SP)
1
2
3
4
1
2
3
4
2 Press selection keys to
select APLAY LISTB, then
press ENTER.
2 Press selection keys to
select APLAY LISTB, then
press ENTER.
DANCE
DANCE
DANCE CURNIV
DANCE CURNIV
[OTHERS]
60min
[OTHERS]
28/07/03 MON 10:00 - 11:00
CH7 SP
EDITING
28/07/03 MON 10:00 - 11:00
CH7 SP
60min
MODIFY
OK
SELECT
DELETE
NAVIGATION
EXIT
CREATE
MODIFY
OK
SELECT
DELETE
NAVIGATION
EXIT
EDITING
CREATE
3 Press selection keys to
select a play list from
which you wish to to
3 Press selection keys to
select a play list which
you wish to move a
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
delete unwanted scenes, then press G.
scene, then press G.
4 Press selection keys to select AEDITINGB, then press ENTER.
5 Press selection keys to
4 Press selection keys to select AEDITINGB, then press ENTER.
5 Press selection keys to
DELETE SCENE
MOVE SCENE
ADD SCENE
DELETE SCENE
MOVE SCENE
ADD SCENE
IN
OUT
IN
OUT
select ADELETE
SCENEB, then press
ENTER.
select AMOVE SCENEB,
then press ENTER.
IN
-:--:--:--
-:--:--:--
IN
-:--:--:--
-:--:--:--
6 Press I to start
OUT
OUT
6 Press I to start
playback.
TOTAL TIME
MOVE TO
:
:
:
TOTAL TIME
:
:
:
-:--:--:--
playback.
● Press O or N to find
the point where you want
the moved scene to
begin, then press W.
TITLE 05 CHAPTER 01
TIME -- --:--:--:--
TITLE 05 CHAPTER 01
TIME -- --:--:--:--
● Press O or N to find
the point where you want
the deletion to begin,
then press W.
RETURN
OK
PREVIEW
NAVIGATION
EXIT
EXECUTE
CLEAR
RETURN
OK
PREVIEW
EXECUTE
CLEAR
NAVIGATION
EXIT
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
SELECT
SELECT
7 Confirm the arrow is on
7 Confirm the arrow is on AINB, then press ENTER.
AINB, then press ENTER.
● The edit-in time is displayed on the left of the AINB window.
● The edit-in time is displayed on the left of the AINB window.
8 Press I to resume playback.
8 Press I to resume playback.
● Press W to pause at the point where you want the moved
scene to end.
● Press W to pause at the point where you want the deletion to
end.
9 Confirm the arrow is on AOUTB, then press ENTER.
9 Confirm the arrow is on AOUTB, then press ENTER.
● The edit-out time is displayed on the left of the AOUTB window.
● The edit-out time is displayed on the left of the AOUTB window.
10Press selection keys
10Press I to start playback.
DELETE SCENE
MOVE SCENE
ADD SCENE
IN
OUT
to select APREVIEWB,
then press ENTER. A
preview of the scene
approximately
● Find the point where you want the moved scene to be moved,
then press W.
-:--:--:--
-:--:--:--
IN
11Confirm the arrow is on AMOVE TOB, then press ENTER.
OUT
:
:
:
TOTAL TIME
12Press selection keys to select APREVIEWB, then press
ENTER. A preview of approximately 5 seconds before and
after the point to which the scene has been moved is played
back.
5 seconds before and
after the deleted part is
played back.
● To cancel the deletion,
press selection keys
to select ARETURNB,
then press ENTER.
TITLE 05 CHAPTER 01
TIME -- --:--:--:--
RETURN
OK
PREVIEW
NAVIGATION
EXIT
EXECUTE
CLEAR
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
● To cancel the moving, press selection keys to select
ARETURNB, then press ENTER.
SELECT
To modify the points
A Press selection keys to select ACLEARB, then press ENTER.
B Press selection keys to select AINB.
C Perform steps 6 - 12.
To modify the points
A Press selection keys to select ACLEARB, then press ENTER.
B Press selection keys to select AINB.
C Perform steps 6 - 10.
13Press selection keys to select AEXECUTEB, then press
ENTER.
11Press selection keys to select AEXECUTEB, then press
ENTER.
14Press NAVIGATION to return to the normal screen.
12Press NAVIGATION to return to the normal screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
50
Add scenes
1 Press NAVIGATION to display the Library Database Navigation
screen.
2 Press selection keys to
ORIGINAL
PLAY LIST
REMAIN TIME
LIBRARY
87min(SP)
select APLAY LISTB, then
press ENTER.
0001
1
2
3
4
3 Press selection keys to
select a play list to which
you wish to add a scene,
then press G.
DANCE
MODIFY
OK
DELETE
EDITING
CREATE
4 Press selection keys to
select AEDITINGB, then
press ENTER.
NAVIGATION
EXIT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
5 Press selection keys to
select AADD SCENEB,
then press ENTER.
DELETE SCENE MOVE SCENE
ADD SCENE
IN
OUT
-:--:--:--
-:--:--:--
IN
6 Press I to start
OUT
TOTAL TIME
playback.
:
:
:
● To move to other titles,
press S or T.
● Press O or N to find
the point where you want
the created play list to
begin, then press W.
TITLE 05 CHAPTER 01
TIME 0000:00:53 **
RETURN
OK
SELECT
PREVIEW
NAVIGATION
EXIT
EXECUTE
CLEAR
SELECT SCENE WITH [PLAY/PAUSE etc.]
THEN PRESS [ENTER]
7 Perform steps 5 - 10 of “Create Play List” (A pg. 47).
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
51
Scan For Title From Library
Edit Library Information
1 Press NAVIGATION to display the Library Database Navigation
screen.
2 Press selection keys to
ORIGINAL
DISC No.
PLAY LIST
CATEGORY
LIBRARY
DATE
select ALIBRARYB, then
press ENTER.
NAME
Each disc recorded on this unit is automatically numbered. If this
number is retained, it is possible to find out the titles recorded in a
disc quickly.
Title information can be registered in the unit’s memory for up to
1300 titles.
3 Select the appropriate
sort button to sort the
information, then press
ENTER.
DELETE
OK
REGISTER
NAVIGATION
EXIT
NOTE:
ADISC No.B:
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
If you do not want the information to be registered in the library
automatically, set ASAVE AS LIBRARYB to AOFFB. (A pg. 59)
Sort by disc number.
ACATEGORYB:
Sort by category.
ADATEB:
SELECT
● Turn on the TV and select an input mode such as EXT1.
Sort by date.
ANAMEB:
Sort by name.
● Each time when the sort button is selected and ENTER is
pressed, the sorting order switches between ascending order
and descending order.
4 Press selection keys to select the desired title, then press
ENTER.
● If the disc loaded on this unit contains the selected title, the
selected title and all subsequent titles will be played back.
When the disc that contains the selected title is not loaded
A prompt screen appears. Load the disc after pressing ENTER to
close the prompt screen.
NAVIGATION
Selection Keys (FGD E)
ENTER
Then perform steps 1 - 4.
NOTE:
If a disc registered in the library is recorded or modified on DVD
units from other manufacturers, it may become impossible to
operate properly.
Register Disc
When a disc that is not recorded on this unit or not registered in the
library is loaded, a message appears confirming if the disc should
be registered. If registering, perform the following procedure.
1 Press NAVIGATION to display the Library Database Navigation
screen.
2 Press selection keys to select ALIBRARYB.
● The registration confirmation screen appears.
ENTER.
● To quit registration, select ACANCELB, then press ENTER.
4 Press NAVIGATION to return to the normal screen.
NOTES:
● It is not possible to register discs used for On-Disc Timer
Programming. (A pg. 39)
● It is not possible to register discs formatted on devices other than
JVC’s DVD recorders.
● It is not possible to register discs recorded on devices other than
JVC’s DVD recorders.
Delete Information
1 Perform steps 1 - 3 of “Scan For Title From Library” (A pg. 51)
before continuing.
2 Press selection keys to select a title whose information you
want to delete, then press G.
3 Press selection keys to select ADELETEB, then press ENTER.
● The confirmation screen appears.
4 Press selection keys to select ADELETEB, then press ENTER.
● To cancel the information deletion, select ACANCELB, then
press ENTER.
5 Press NAVIGATION to return to the normal screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
EN
52
Locating The Desired Group And Tracks
Playback With MP3/JPEG Navigation
1 Load a disc.
2 Press NAVIGATION.
3 Press selection keys to select AMP3B or AJPEGB, then press
This unit can play back discs that MP3 sound files and JPEG
image files taken with digital still cameras or other devices are
recorded.
The MP3/JPEG Navigation enables you to search and select the
desired files recorded on CD-R/RW or CD-ROM discs very easily.
ENTER.
4 Press selection keys to select the desired group, then press
ENTER.
● A list of files in the selected group appears.
● Turn on the TV and select an input mode such as EXT1.
then press ENTER. The unit starts playback from the selected
file.
played back.
A
B
C
NOTES:
MY BEST
MP3
● If you press I instead of ENTER in step 4, the unit starts
playback from the first file of the group.
1/1
JPEG
● JPEG files are played back as a slide show at the set intervals.
(A pg. 33)
● If a file name includes any 2 byte character, the unit may not
show the file name correctly.
ROOT
Europe
Pops
Rock
20/11/03 THU 20/11/03 THU 20/11/03 THU 20/11/03 THU
MUSIC/FRANCE/POPS
20/11/03 THU
● The order of the groups and items shown in steps 4 and 5 may
RETURN
differ from the order shown on your PC.
OK
NAVIGATION
EXIT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
● When you want the multiple files to be played back continuously,
specified order when I is pressed. (Up to 30 titles)
● If you have specified a wrong selection, press CANCEL.
Or press CLEAR(o), all the title numbers are erased.
SELECT
D
E
F
G
H
I
SONG SONG
another. mp3
After all the files are played back
A Perform steps 1 - 4.
1/48
01SONG
02SONG
03SONG
04SONG
05SONG
06SONG
07SONG
SONG
SONG
SONG
SONG
SONG
SONG
B Press CLEAR(o).
08SONG
09SONG
10SONG
11SONG
12SONG
● The title numbers are reset and erased.
C Press NAVIGATION to return to the normal screen.
1
2
RETURN
OK
NAVIGATION
EXIT
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
J
A Name of the inserted disc
B Sort buttons (AMP3B / AJPEGB)
C Selected group number/total number of groups on the disc
D Group name
E Return button
F Group name/Created date
G File type indicator
c
: MP3
d : JPEG
H Selected file
I Selected file number/total number of files in the group that
contains the selected file
J Program number/file name
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
53
1 Connect a camcorder or DV equipment to the [DV IN]
connector on the unit’s front panel.
DV Dubbing
2 Press CH +/– to set the channel to ADVB.
You can dub programs from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
● The on-screen display for DV dubbing appears.
3 Press REC MODE repeatedly to set the recording mode.
4 Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: I, N, O, o, W.
NOTES:
● To play back in slow speed (1/10 of the normal speed), press W
to pause playback, then press O or N.
● To play back frame-by-frame, press W to pause playback, then
press W repeatedly. Each press of W advances a frame.
● To change the playback direction, press O or N.
● Use the DV cable VC-VDV 204U for connection.
● When you connect a PC to the [DV IN] connector, we do not
assure the normal operation of this unit.
5 Press selection keys to select
, then press ENTER
repeatedly until the desired sound track appears on the TV
screen.
Your unit
RAM/RW
AUDIO 1:
Select this to record the original stereo sound played back on
the connected DV equipment.
AUDIO 2:
To [DV IN]
Select this to record the dubbed stereo sound played back on
the connected DV equipment.
MIX:
Select this to record the sound of both AAUDIO 1B and AAUDIO
2B.
● Note that this selection is not available when the source
program is recorded in 16BIT (48 kHz) mode.
Camcorder
DV cable
(VC-VDV 204U)
(not supplied)
6 Press selection keys to select
, then press ENTER.
The dubbing starts.
● Playback on the external DV equipment and recording on the
unit should start simultaneously.
● To pause dubbing, press selection keys to select
then press ENTER. Both the unit and the external DV
equipment pause dubbing.
,
DV connector
● To resume dubbing, press selection keys to select
then press ENTER to start dubbing.
,
DV equipment
7 Press o to stop dubbing.
● Both the unit and the external DV equipment stop dubbing.
NOTES:
● Dubbing copyright guarded programs is not possible.
● Original DV information such as the recording date and time are
not recorded.
● The superimposed indication during the operation or dubbing is
not recorded.
● If the dubbing is paused while the channel is set to ADVB, you
cannot switch channels.
The following on-screen display for DV dubbing appears when
ON SCREEN is pressed while the channel has been set to ADVB.
DV DUBBING
AUDIO 1
1
2
DV
DV
● Only DV format video can be dubbed. It is not possible to dub
MPEG2 format video.
A
B
C
A DV dubbing controller
When you dub from DV equipment other than a
camcorder
If this mark is not displayed, check whether the DV equipment
has been connected to the unit.
A Perform steps 1 - 3.
B Locate the point from where you want to start dubbing,
then stop on the DV equipment.
● If you pause the DV equipment in this step, a few
the recorded program.
Select to start or pause the dubbing. If ENTER is pressed when
the DV device is in the pause condition, preroll editing* where it
is possible to dub with a start time that is highly accurate will be
activated. When the DV device cannot be operated from the
unit (such as in camera mode), proceed with normal recording
(A pg. 34).
* Preroll editing refers to the playback after the DV tape is slightly
rewind. (For DV devices that do not support the –1x speed, the
rewinding time may be longer.)
C
Set the input mode to ADV INPUTB on the DV equipment.
● If input mode is set to other than ADV INPUTB, unwanted
pictures may be recorded at the beginning of the
recorded program.
D Perform steps 6 and 7.
C Sound monitor switch
For selecting the desired sound format for dubbing.
To skip unwanted part of the source picture
Press ENTER to stop both equipment, press I, N or O to
locate the point where you want to resume dubbing, then press o.
Press selection keys to select
start dubbing.
, then press ENTER to
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
54
1 Make connections.
A If the camcorder has no S-VIDEO output connector:
^ connect the camcorder’s AUDIO/VIDEO OUT connectors to
the unit’s [VIDEO/AUDIO (L(MONO)/R)] input connectors on
the front panel.
Edit From A Camcorder
You can use a camcorder as the source player and your unit as the
recording deck.
● When using a monaural camcorder, connect its AUDIO OUT
connector to the [AUDIO(L(MONO))] input connector on your
unit.
A If the camcorder has no S-VIDEO output connector:
B If the camcorder has an S-VIDEO output connector:
connectors to the unit’s [AUDIO] and [S-VIDEO] input
connectors on the front panel.
RAM/RW
Recorder
2 Press CH +/– to select AF-1B.
To [VIDEO/AUDIO
(L(MONO)/R)] input
● Set AFRONT AUX F-1B to AVIDEOB for the [VIDEO] input
connector, or AS-VIDEOB for the [S-VIDEO] input connector,
depending on the connector being used. (A pg. 59)
3 Press REC MODE repeatedly to set the recording mode.
4 Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
Audio/video cable
(not supplied)
5 Press R on the unit to start recording. Or while holding R, press
I on the remote control. The dubbing starts.
6 Upon completing dubbing, stop the unit and the camcorder.
● Stop recording on the recording deck (your unit), then stop
playback on the source player (camcorder).
Player
NOTES:
● All necessary cables can be obtained from your dealer.
● Refer to the camcorder’s instruction manual for operating
procedure.
AUDIO/VIDEO OUT
● The quality of dubbed picture are poorer than that of the original.
B If the camcorder has an S-VIDEO output connector:
RAM/RW
Recorder
To [S-VIDEO]
input
To [AUDIO]
input
S-video cable
(not supplied)
Audio cable
(not
supplied)
S-VIDEO OUT
Player
AUDIO OUT
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
55
1 Make connections.
A When using your unit as the source player
Edit To Or From Another Recorder
^ connect it’s [S-VIDEO/VIDEO/AUDIO OUTPUT] connectors
to the input connectors on another recorder.
B When using your unit as the recording deck
You can use your unit as the source player or as the recording
deck.
^ connect it’s [L-1/F-1] connectors on the front or rear panel to
the output connectors on another recorder.
● When connecting to another recorder with S-Video connector,
set AREAR AUX L-1B or AFRONT AUX F-1B to AS-VIDEOB.
NOTE:
When using another recorder as the recording deck, refer to its
instruction manual.
2 Press CH +/– to select the external input.
A When using your unit as the source player
● Select AF-1B when the source player is connected to the unit’s
[VIDEO/AUDIO] or [S-VIDEO/AUDIO] input connectors on the
front panel, and select AL-1B when it is connected to the unit’s
[VIDEO/AUDIO] or [S-VIDEO/AUDIO] input connectors on the
rear panel.
TV receiver
Your unit
Player
3 Press REC MODE repeatedly to set the recording mode.
4 Engage play mode on the source player.
5 Engage record mode on the recording deck.
6 Stop recording on the recording deck, then stop playback on
the source player.
S-Video cable
Audio/video
cable
Audio/video
cable
NOTES:
● All necessary cables can be obtained from your dealer.
● When you use this unit as the source player for editing, be sure to
set ASUPERIMPOSEB or AOFFB before starting. (A pg. 59)
Another recorder
Recorder
B When using your unit as the recording deck
TV receiver
Recorder
Your unit
Audio/video
cable
Audio/video
cable
S-Video cable
Another recorder
Player
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
56
1 Connect the unit and a digital audio device using an optional
coaxial cable.
Digital Audio Dubbing
2 Place a disc on the unit and load an MD on the connected
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
digital audio device.
3 Select the audio to be dubbed.
However, it is not possible to dub copy-protected discs.
4 Start playback slightly before the actual point from where you
● Turn on the TV and select an input mode such as EXT1.
wish to start dubbing.
5 Press W to pause playback.
Example: Dubbing to an MD
6 Select the input mode on the connected digital audio device.
7 Press I to start playback on the unit.
Recorder
8 Start recording on the digital audio device.
9 Stop recording on the digital audio device. Then press o to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
Digital audio device (MD
deck, etc.)
Coaxial cable
(not supplied)
To [DIGITAL OUT
(COAXIAL)]
Player
Rear of unit
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL/SYSTEM CONNECTIONS
EN
57
Remote Control Functions
Remote Control 1/2/3/4 Code Switching
The remote control is capable of controlling four JVC video units
independently. Each of the units can respond to one of the four
codes (1, 2, 3 or 4). The remote control is preset to send code 3
signals because your unit is initially set to respond to code 3
signals. You can easily modify your unit to respond to code 1, 2 or
4 signals.
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
RAM/RW
Dolby Digital Decoder or
amplifier with built-in DTS
A
I
To DIGITAL AUDIO
input
Coaxial cable
(not supplied)
1-4
To [DIGITAL OUT
(COAXIAL)]
ENTER
Rear of unit
1 Connect the unit and a Dolby Digital Decoder or an amplifier
with built-in DTS using an optional coaxial cable.
NOTE:
o
For details on [DIGITAL OUT] connector setting, refer to “DIGITAL
AUDIO OUT”. (A pg. 58)
SET UP
● Keep pressing SET UP down during step 1.
1 Press the number key “1” for 1, “2” for 2, “3” for 3 or “4” for 4 to
change the remote control code, then press ENTER.
2 Press A on the unit to turn off the unit.
3 Press I on the unit for over 5 seconds while the unit is turned
off. The code currently set appears on the front display panel.
4 Press o on the remote control to change the unit’s code. The
code currently set on the remote control blinks on the front
display panel for approximately 5 seconds, and is applied to the
unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
58
* The boldface settings below indicate the settings at your purchase.
Mode Set
AUDIO OUTPUT
8 DIGITAL AUDIO OUT ^ DOLBY DIGITAL/PCM / STREAM/
PCM / PCM ONLY
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
Set to the appropriate mode according to the type of the device
connected to [DIGITAL OUT] connector.
DOLBY DIGITAL/PCM:
Select this when you connect the digital input connector of a
Dolby Digital Decoder or an amplifier with a built-in Dolby Digital
Decoder.
STREAM/PCM:
Select this when you connect the digital input connector of an
amplifier with a built-in DTS, Dolby Digital, or MPEG
multichannel decoder.
PCM ONLY:
Select this when you connect the linear PCM digital input of
other audio equipment (amplifier, MD or DAT deck, etc.).
Selection Keys (FGD E)
ENTER
NOTE:
If you watch or play back a program recorded on a DVD-RAM or
DVD-RW (VR mode only) disc which contains multiple audio
languages, select “PCM ONLY” in advance and choose main or
sub audio with AUDIO.
8 ANALOG AUDIO OUT ^ STEREO / DOLBY SURROUND
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
SET UP
AUDIO
STEREO:
Select this when listening to conventional two-channel stereo
audio with the unit’s [AUDIO OUTPUT] connectors connected
to a stereo amplifier/receiver or TV set, or in case you want to
record the audio from a DVD VIDEO disc to a Mini Disc, etc.
Various modes of this unit are categorized into menus nested in
these modes, find the desired mode in the menu, then follow the
procedure below. (For details on each menu, see pages 58
through 59)
DOLBY SURROUND:
Select this when listening to audio with the unit’s [AUDIO
OUTPUT] connectors connected to an amplifier/receiver with a
built-in surround decoder or a surround decoder.
DVD SET UP
UTILITY (A pg. 62, 63)
8 D. RANGE CONTROL ^ NORMAL / WIDE RANGE / TV MODE
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a program
encoded in Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
FUNCTION SET UP
RECORDING SET (A pg. 59)
DISPLAY SET (A pg. 59)
OTHERS (A pg. 60)
NORMAL:
INITIAL SET UP
TUNER SET (A pg. 20)
CLOCK SET (A pg. 19)
Normally select this setting to activate this function.
WIDE RANGE:
Select this to deactivate this function when you enjoy wide
dynamic range program.
● The procedure below shows how to set the desired option of the
“2ND AUDIO RECORD” mode as an example.
TV MODE:
1 Press SET UP to access the Main Menu screen.
Select this when connecting to a TV. Even soft sound can be
well heard.
2 Press selection keys to select “FUNCTION SET UP”, then
press ENTER.
NOTES:
● This function has no effect on programs other than those
recorded in Dolby Digital format.
3 Press selection keys to
DVD SET UP
FUNCTION SET UP INITIAL SET UP
OTHERS
select “RECORDING
SET”, then press
ENTER.
VIDEO IN/OUT RECORDING SET DISPLAY SET
● The effect of “NORMAL” and “WIDE RANGE” may not be
different depending on discs.
SAVE AS LIBRARY
XP MODE REC AUDIO
2ND AUDIO RECORD
ON
DOLBY DIGITAL
4 Press selection keys to
select “2ND AUDIO
RECORD”, then press
ENTER.
OFF
OFF
8 OUTPUT LEVEL ^ STANDARD / LOW
ON
You can lower the output level of analogue audio to accommodate
the unit to the connected A/V equipment.
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
STANDARD:
5 Press selection keys to
SELECT
Normally select this setting.
select the desired
LOW:
setting, then press ENTER.
The output level of analogue audio is lowered.
6 Press SET UP to complete the setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
59
VIDEO IN/OUT
DISPLAY SET
8 MONITOR TYPE ^ 4:3LB / 4:3PS / 16:9AUTO / 16:9FIX
For details, refer to “Monitor Set” (A pg. 21).
8 SUPERIMPOSE ^ OFF / AUTO
When this function is set to “AUTO”, various operational indicators
appear on the TV screen.
8 FRONT AUX F-1 ^ VIDEO / S-VIDEO
OFF:
Select the appropriate mode depending on the F-1 connector
([VIDEO] or [S-VIDEO]) being used on the front panel.
To turn off superimposed indications.
AUTO:
VIDEO:
To superimpose operational indications for approximately five
seconds just after the corresponding operation.
To use the [VIDEO] input connector.
S-VIDEO:
NOTES:
To use the [S-VIDEO] input connector.
● Even when “SUPERIMPOSE” is set to “OFF”, you can display
the various operational indicators by pressing ON SCREEN on
the remote control. To clear the operational indicators, press
ON SCREEN again.
● When you use this unit as the source player for editing, be sure to
set “SUPERIMPOSE” to “OFF” before starting. (A pg. 55)
● When you select “AUTO”, during playback, the operation mode
indicators may be disturbed depending on the type of disc being
used.
8 REAR AUX L-1 ^ VIDEO / S-VIDEO
Select the appropriate mode depending on the L-1 connector
([VIDEO INPUT] or [S-VIDEO INPUT]) being used on the rear
panel.
VIDEO:
To use the [VIDEO INPUT] connector.
S-VIDEO:
To use the [S-VIDEO INPUT] input connector.
OFF:
RECORDING SET
Select this when you want to receive an unstable channel with
poor signals.
8 SAVE AS LIBRARY ^ OFF / ON
ON:
When this function is set to “ON”, the recording information is
automatically stored in the library. For details, refer to “Edit Library
Information” (A pg. 51).
When this function is set to “ON”, the TV screen becomes all
gray when receiving a channel not in use.
8 DIMMER ^ BRIGHT / DIMMED1 / DIMMED2 / OFF
8 XP MODE REC AUDIO ^ DOLBY DIGITAL / LINEAR PCM
You can select the audio format when you record a title in XP
mode. When this function is set to “LINEAR PCM”, you can obtain
a high-quality audio sound.
You can change the brightness of the front display panel.
BRIGHT:
Normally select this. To turn on the display and blue lamp of the
front display panel.
DOLBY DIGITAL:
To record in Dolby Digital format.
DIMMED1/DIMMED2:
To change the brightness level, and turn off the blue lamp of the
front display panel.
LINEAR PCM:
To record in Linear PCM format.
OFF:
To turn off the display and blue lamp of the front display panel.
8 2ND AUDIO RECORD ^ OFF / ON
When this function is set to “ON”, if a SAP program is received, the
SAP audio is recorded on L/R tracks. The main audio is not
recorded. If a non-SAP program is received, the main audio is
recorded on L/R tracks.
8 POWER SAVE ^ OFF / ON
When this function is set to “ON”, you can reduce the power
consumption while the unit is turned off.
When this function is set to “OFF”, the SAP audio cannot be
recorded.
NOTES:
● During Power Save mode ^
NOTE:
^ the front display panel will be turned off.
^ the Automatic Satellite Program Recording mode is engaged.
When the channel is changed on the unit;
● The “MONO” indicator appears on the screen for about 5
seconds if the program is a monaural broadcast.
● The “STEREO” indicator appears on the screen for about 5
seconds if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo
program is accompanied by SAP sound.
8 ON SCREEN LANGUAGE^ ENGLISH / FRANCAIS / ESPAÑOL
This unit offers you the choice to view on-screen messages in
3 different languages.
● For details, refer to “On-screen Language Set” (A pg. 18).
● Both “MONO” and “SAP” indicators appear when the main
audio on the monaural broadcast is accompanied by SAP
sound.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
60
OTHERS
Scan Mode Set
8 AUTO TIMER ^ OFF / ON
If you connect the unit and TV with Component Video Connection
(A pg. 12), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV
system, and Progressive scan mode which enables reproduction
of higher-quality images.
This is the setting for engaging timer recording standby mode.
OFF:
Press j to engage timer recording standby mode.
ON:
Timer recording standby mode is automatically engaged when
the unit is turned off.
8 Interlaced scan
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of
the second half of the picture in-between lines of the first half of the
picture.
8 RESUME ^ OFF / ON / DISC RESUME
When this function is set to “ON” or “DISC RESUME”, you can use
the resume function. (A pg. 24)
8 Progressive scan
OFF:
Progressive scan displays all the horizontal lines of a picture at
one time, as a single frame. This system can convert the interlaced
video from DVD into progressive format for connection to a
progressive display. It dramatically increases the vertical
resolution.
You cannot use the resume function.
ON:
The resume function works on the disc loaded on the unit.
DISC RESUME:
The unit retains a memory of the resume points of the last
30 discs played back, even though they have been ejected.
ATTENTION:
● Your TV needs to be compatible with Progressive.
● Connect the unit and the TV using a component video cable.
NOTE:
“DISC RESUME” setting works on DVD-VIDEO, VCD, SVCD and
finalized DVD-R/DVD-RW (Video mode) discs. For other types of
discs, the function under “ON” setting will be applied even if
“RESUME” is set to “DISC RESUME”.
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
DVD A
PROGRESSIVE SCAN
1 Press PROGRESSIVE SCAN for 3 or more seconds.
● Video output indicator (q) lights on the front display panel if
Progressive scan mode has been established. (A pg. 13)
● Each press of PROGRESSIVE SCAN for 3 or more seconds
switches the scan mode.
NOTES:
● Progressive scan video signal is output from the [COMPONENT
VIDEO OUT (Y/PB/PR)] connectors. It will not be output from the
[VIDEO OUTPUT] and [S-VIDEO OUTPUT] connectors.
● Interlaced scan mode is the setting at your purchase.
● Interlaced scan mode might be suitable depending on video
material.
● Scan mode cannot be set while menu screen is displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
61
Tray Lock
Child Lock
You can lock the disc tray to prohibit the unwanted disc ejection by
children.
You can disable the operations of this unit using the Child Lock
function.
● Turn on the unit.
M
o
1 When the unit is turned on, press and hold DVD A on the
remote control for more than 10 seconds.
RAM/RW
● The unit turns off and enters into Child Lock mode.
● When in Child Lock mode, “CL” will appear on the front display
panel indicating that Child Lock mode is engaged when an
attempt was made to operate buttons on the unit or remote
control.
To lock tray
When the unit is turned off, while holding o, press M on the unit.
“LOCK” appears on the front display panel and the disc tray is
locked.
2 Press and hold DVD A on the remote control for more than
10 seconds.
● Child Lock is released and the unit turns on.
To unlock tray
When the unit is turned off, while holding o, press M on the unit.
“UNLOCK” lights up on the front display panel.
NOTE:
When in Child Lock mode, pressing TIMERj during timer
recording releases Child Lock and recording is continued.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
62
Guide Channel Number Set
Changing VCR Plus+ Setting
1 Press SET UP to access the Main Menu screen.
2 Press selection keys to
The VCR Plus+ programming system assigns a VCR Plus+ guide
channel number to the TV channels and the cable channels. These
guide channel numbers are also called the VCR Plus+ channel
codes.
DVD SET UP
TUNER SET
FUNCTION SET UP INITIAL SET UP
select “INITIAL SET UP”,
CLOCK SET
then press ENTER.
BAND
CATV
3 Press selection keys to
select “TUNER SET”,
then press ENTER.
Most TV listings have a section, usually a chart, indicating the
guide channel numbers assigned to each station. To ensure that
VCR Plus+ timer recording operates correctly, it is necessary to
set the VCR Plus+ Guide Channel for each station.
AUTO CH SET
MANUAL CH SET
GUIDE CHANNEL SET
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, perform the steps on the right
column to set the correct guide channel number.
SET UP
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
EXIT
4 Press selection keys to
select “GUIDE
DVD SET UP
FUNCTION SET UP INITIAL SET UP
NOTES:
INITIAL SET UP / GUIDE CHANNEL SET
● In many instances, the VCR Plus+ guide channel numbers for
cable and broadcast TV stations DO NOT match the channel
number on which it is received by your unit. Check your TV
listing, or contact your cable supplier for details.
● Many TV stations can be viewed on cable. Check your TV listing,
or contact your cable supplier for details.
CHANNEL SET”, then
press ENTER.
GUIDE CH
DVD CH
1
---
5 Press selection keys to
select “GUIDE CH”, then
press ENTER.
RETURN
6 Press selection keys to
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
select the Guide
SELECT
Channel number for the
● To change the Guide Channel number in 10 channel
increments, press and hold F G.
7 Press selection keys to select “DVD CH”, then press ENTER.
8 Press selection keys to select the channel number of the unit
on which desired broadcast is received, then press ENTER.
● Repeat steps 4 - 8 as necessary.
9 Press SET UP to complete the setting.
Guide Channel Number
“Guide Channel (GUIDE CH) Number” refers to the assigned TV
station numbers, according to broadcast area, for the VCR Plus+
timer recording. The Guide Channel Numbers can be found in
most TV listings.
Selection Keys (FGD E)
ENTER
SET UP
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
63
Format A DVD-RAM Disc
Format A Disc
1 Press SET UP to access the Main Menu screen.
2 Press selection keys to select “DVD SET UP”, then press
ENTER.
Some DVD-RAM/RW discs are unformatted.
Format the disc when you use an unformatted disc or you want to
delete all recordings and data on the disc.
3 Press selection keys to
DVD SET UP
FUNCTION SET UP INITIAL SET UP
AUDIO OUTPUT UTILITY
select “UTILITY”, then
LANGUAGE SET
press ENTER.
FORMAT
FINALIZE
4 Press selection keys to
select “FORMAT”, then
press ENTER.
● The confirmation screen
appears.
ATTENTION:
CANCEL DISC FINALIZATION
● When a disc is formatted, all recordings and data are erased. It
is impossible to restore them.
● Never turn off the unit or disconnect the AC power cord while
“NOW FORMATTING...” is displayed on the TV screen.
SET UP
EXIT
OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
5 Press selection keys to
select “YES”, then press
ENTER.
SELECT
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
● Load a DVD-RAM/RW disc to format.
● The confirmation screen appears.
6 Press selection keys to select “OK”, then press ENTER.
screen. Press ENTER to complete formatting.
8 Press SET UP to return to the normal screen.
Format A DVD-RW Disc
1 Perform steps 1 - 3 of “Format A DVD-RAM Disc” as above
before continuing.
2 Press selection keys to select “FORMAT”, then press ENTER.
Press selection keys to choose “VR MODE” or “VIDEO
MODE”, then press ENTER when “DISC WILL BE
FORMATTED” appears on the TV screen.
“VR MODE”:
Selection Keys (FGD E)
ENTER
To be chosen when you want to record, erase, or edit data on
the disc repeatedly.
“VIDEO MODE”:
To be chosen when you want to erase all the data on the disc
once played back to record new data, or play back the disc on
other DVD players.
3 Press selection keys to select “YES”, then press ENTER.
SET UP
4 Upon completing formatting, “COMPLETED” appears on the TV
screen. Press ENTER to complete formatting.
5 Press SET UP to return to the normal screen.
NOTES:
● It is impossible to format Version 1.0 DVD-RW discs in Video
mode.
● It is impossible to format DVD-R discs.
● All the titles on a disc will be deleted once the disc is formatted
even if they are protected titles.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUBSIDIARY SETTINGS
EN
64
Finalize A DVD-R/RW Disc
Finalize A Disc
1 Perform steps 1 - 3 of “Format A DVD-RAM Disc” (A pg. 63)
before continuing.
2 Press selection keys to select “FINALIZE”, then press ENTER.
3 The confirmation screen appears. Press selection keys to
Finalizing DVD-R/RW discs recorded on this unit makes it possible
for the discs to be played back on other DVD players. DVD-RW
discs are finalized in the mode that the discs were formatted,
enabling playback on compatible DVD players.
Title names input in the Library Database Navigation are
registered as title names in the DVD menu. (A pg. 51)
select “YES”, then press ENTER.
4 The confirmation screen appears again. Press selection keys
to select “OK”, then press ENTER.
● To cancel finalization, press “CANCEL”.
5 Upon completing finalization, “COMPLETED” appears on the
TV screen. Press ENTER to return to the previous screen.
ATTENTION:
6 Press SET UP to return to the normal screen.
● Menu screen is cleared.
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. As only the
display for library appears, press TOP MENU to select the
desired title.
● Never turn off the unit or disconnect the AC power cord while
finalization or cancellation of finalization is in progress.
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
● Load a DVD-R/RW disc to finalize.
played on DVD players compatible with VR mode.
Cancel The Finalization Of A DVD-RW Disc
1 Load a DVD-RW disc to cancel the disc finalization, and
perform steps 1 - 3 of “Format A DVD-RAM Disc” (A pg. 63)
before continuing.
2 Press selection keys to select “CANCEL DISC
FINALIZATION”, then press ENTER.
3 Press selection keys to select “OK”, then press ENTER.
4 Upon completing cancellation of finalization, “COMPLETED”
appears on the TV screen. Press ENTER to return to the
previous screen.
TOP MENU
Selection Keys (FGD E)
ENTER
5 Press SET UP to return to the normal screen.
● When the disc finalization is canceled, the mode in which the
disc was formatted is restored, making the disc recordable.
● It is not possible to cancel the finalization of a DVD-R disc.
SET UP
Before finalizing
● It is possible to record on a blank space.
● It is possible to enter title names. (A pg. 46)
● It is possible to delete titles. (A pg. 44)
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
program is deleted from a DVD-R disc.
● It is impossible to record or edit DVD-R/RW discs recorded on
other devices even if they have not been finalized.
After finalizing (For DVD-R/RW (Video mode) discs)
● Video and audio that are recorded in conformity to the DVD
Video standard before finalizing enables you to play back the
discs as DVD VIDEO discs.
● Although DVD-R/RW discs finalized on this unit become playable
on DVD players compatible with DVD-R/RW discs, some discs
still may not play, for which JVC cannot take responsibility.
● Marked points marked before finalizing will be deleted, and titles
will be divided automatically into “chapters” approximately every
5 minutes. (A pg. 9, 25)
● Depending on the DVD players and DVD-R/RW discs used, and
on the conditions of recording, it may not be possible to play back
the discs. In this case, play back the discs on this unit.
● Additional recordings become impossible.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
65
Before requesting service for a problem, use this chart and see if
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off
for repair.
Playback
Images do not appear on the TV screen.
●
The TV receiver’s channel selector is not set to an input mode
such as EXT1.
Initializing
] Set the TV to an input mode such as EXT1.
●
When interlace scanned program is played back, progressive
scan mode is selected.
Malfunction occurs on the unit.
] Press A to turn off the unit, press and hold A, then press o
] Press and hold PROGRESSIVE SCAN until q disappears
for 3 seconds or more.
from the front display panel. (A pg. 60)
Playback does not start or stop immediately after playback is
started by pressing I.
On the front display panel, “NO DISC” appears.
General
No power is supplied to the unit.
●
The AC power plug is disconnected from the AC outlet.
●
The disc is loaded upside down.
] Connect the AC power plug to the AC outlet securely.
] Place the disc on the disc tray with the playback surface facing
(A pg. 16)
down. (A pg. 10)
●
A disc not being compatible with the unit is loaded.
] Load a playable disc on the unit. (A pg. 8)
A dirty disc is loaded.
] Clean the disc. (A pg. 11)
Defective disc is loaded.
The remote control does not work properly.
] Remove the batteries, wait for 5 minutes or more, then load the
●
butteries again.
●
●
The setting of the remote control code is inappropriate.
] Replace the warped or scratched disc with a normal one.
] Set the same remote control code (1, 2, 3, or 4) on both the unit
and the remote control. (A pg. 57)
The batteries are discharged.
] Replace the dead batteries with new ones.
Images are blurred or distorted when you start High-Speed
Search.
●
] Images are blurred or distorted at the point where the playback
Dubbing from the external equipment is not possible.
speed changes and this is not a malfunction of the unit.
●
The source (another video recorder, camcorder) has not been
properly connected.
Playback does not start.
All necessary power switches have not been turned on.
] Confirm that all units’ power switches are turned on.
The setting of the input channel position is inappropriate.
] Select the input channel position (“F-1” or “L-1”) that
equipment. (A pg. 54)
] Playback does not start for approximately 30 seconds after
●
recording is stopped and this is not a malfunction of the unit.
●
The desired program cannot be recorded.
●
The channel position does not correspond to that in the
receiving area.
The on-screen display superimposed on the program played
back/received on this unit is recorded when you dub the
program to an external recording equipment.
] Set the correct channel position for the receiving broadcast.
(A pg. 20)
] Set “SUPERIMPOSE” to “OFF”. (A pg. 59)
Recording cannot be made.
The unit does not operate.
●
No disc or a disc not being compatible with the unit is loaded.
] Load a recordable disc on the unit. (A pg. 7)
The disc loaded is not formatted.
] Format the disc. (A pg. 63)
●
●
There are cases when the operation is prohibited on the disc.
Lightning or static electricity may cause malfunction of the unit.
●
●
again. Then turn on the unit.
] Recording cannot be made on finalized discs. Load a
recordable disc on the unit.
The disc is full or does not have enough space for the title to be
recorded.
The remote control of a JVC TV will not operate the unit.
●
●
The setting of the remote control code is inappropriate.
] To operate the unit using a JVC TV remote control, set the
] Clear unnecessary titles on the disc or load a blank disc.
remote control code of the unit to “1” (Default: “3”). (A pg. 57)
(A pg. 44)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
66
Timer Recording
Other Problems
Timer programming cannot be made.
The image of the TV broadcast appears distorted on the TV
screen.
●
Date and time is not correct.
] Set date and time correctly. (A pg. 17, 19)
Timer recording is in progress.
] Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (q) lights off on the front display panel.
●
] Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
Whistling or howling is heard from the TV during camcorder
recording.
Timer programming recording does not start.
●
The camcorder’s microphone is too close to the TV.
] Position the camcorder so its microphone is away from the TV.
The TV’s volume is too high.
●
Date and time is not correct.
] Set date and time correctly. (A pg. 17, 19)
●
] Turn the TV’s volume down.
●
Date and time is not correct.
When scanning channels, some of them are skipped over.
] Set date and time correctly. (A pg. 17, 19)
●
●
Those channels have been designated to be skipped.
The channel position does not correspond to that in the
receiving area.
] If you need the skipped channels, restore them using “Manual
Channel Set” (A pg. 20).
] Set the correct channel position for the receiving broadcast.
(A pg. 20)
Channel settings that were made manually seem to have
changed or disappeared.
The VCR Plus+ system does not timer record properly.
●
After the manual settings were made, Auto Channel Set was
performed.
●
The unit’s channel positions have been set incorrectly.
] Do no perform Auto Channel Set after making manual settings,
perform the procedure.
proceed to perform “Clock Set” (A pg. 19).
Automatic Satellite Programme Recording does not start.
Malfunction occurs and the unit cannot be power off.
●
The DBS receiver is not connected properly to this unit.
] Reset the unit by disconnecting the AC power plug from the AC
] Connect the DBS receiver correctly to the unit’s [L-1 INPUT]
outlet and connect again.
connectors. (A pg. 42)
On the front display panel, “- - : - -” appears.
●
Power failure occurred.
] Set date and time correctly. (A pg. 19)
The disc space does not increase when recorded titles are
cleared.
●
The PC’s data recorded on a DVD-RAM drive cannot be
cleared on this unit.
] Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (A pg. 11, 63)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
67
On-screen Message
RECOGNIZED
MAKE SURE THAT THE DEVICE IS CONNECTED PROPERLY
AND POWERED ON
DISC NOT REGISTERED IN THE LIBRARY
REGISTER DISC?
● An attempt has been made to start DV dubbing when a digital
video camera is not properly connected to the unit.
● Check the connection. (A pg. 53)
● A disc that is not registered in the library has been inserted.
Register the disc as necessary. (A pg. 51)
INSERT DISC #XXXX
MEMORY IS FULL
● Appears when a title that has been selected in the library is not
contained in the loaded disc.
NOTHING MORE CAN BE REGISTERED IN THE LIBRARY
IF YOU DELETE UNNECESSARY TITLE INFORMATION,YOU
CAN THEN REGISTER ADDITIONAL INFORMATION
CAN NOT RECORD OR MAKE PLAY LIST
DELETE UNWANTED TITLES
● The memory for registration for the Navigation system is full. The
recording cannot be started even though the capacity for the
recording is enough.
● The number of titles exceeds 99.
● The number of play lists exceeds 99.
AVAILABLE MEMORY IS LOW
SOON YOU WILL NO LONGER BE ABLE TO REGISTER
INFORMATION IN THE LIBRARY
IF YOU DELETE UNNECESSARY TITLE INFORMATION,YOU
CAN THEN REGISTER ADDITIONAL INFORMATION
SET CLOCK BEFORE TIMER PROGRAMMING
● To set the timer program, the clock must be set in advance.
(A pg. 19)
● The remaining capacity of the memory is not enough for
registration for the Navigation system. The recording cannot be
started even though the capacity for the recording is enough.
PROGRAM FULL
DELETE UNWANTED TIMER PROGRAMS
● You can program this unit to timer record as many as
program already set. (A pg. 41)
CAN NOT SET DISC TIMER PROGRAMING WITH THIS DISC
PREPARE A FORMATTED DISC AS DESCRIBED BELOW
DVD-RAM
DISC NOT RECORDABLE
INSERT RECORDABLE DISC
DVD-RW (VR MODE)
● On-Disc Timer Programming has been attempted when a disc
that is not compatible with the function is loaded.
● When a playback-only disc or a finalized disc is loaded, R has
been pressed. (A pg. 8)
NO DISC INSERTED
REGION CODE ERROR CHECK DISC
● On-Disc Timer Programming has been attempted when a disc is
not loaded, or loaded upside down.
number of the disc does not match that of the unit. (A pg. 8)
PLUSCODE NO. ERROR
UNREADABLE DISC
CHECK DISC
CONFIRM PLUSCODE NO. THEN RETRY
● An invalid PlusCode number has been input.
(A pg. 8)
GUIDE PROGRAM IS NOT SET
SELECT CHANNEL YOU WANT TO RECORD
COULD NOT FORMAT THE DISC
CHECK THE DISC
Channel Number must be set in advance.
● Formatting is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (A pg. 11, 63)
CAN NOT SET VCR PLUS+ TIMER PROGRAMING DURING
TIMER RECORDING OR INSTANT TIMER RECORDING
CANCEL TIMER RECORDING OR INSTANT TIMER
RECORDING, THEN ENTER THE PLUSCODE AGAIN
PRESS [STOP] AGAIN TO STOP RECORDING
● During Live Memory playback, o has been pressed. (A pg. 27)
● Appears when you tried to input a PlusCode number during timer
recording or instant timer recording.
TIMER RECORDING COMPLETED
● Timer recording has finished during Live Memory playback.
COULD NOT FINALIZE THE DISC
CHECK THE DISC
PLAYBACK WILL STOP THEN TIMER RECORDING WILL
START
● Finalizing is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry.
● Timer recording finished during Live Memory playback, then the
next timer recording is about to begin while playback continues.
COULD NOT CANCEL DISC FINALIZATION
CHECK THE DISC
COPY PROHIBITED
CAN NOT RECORD
● Canceling disc finalization is not complete since the disc may be
dirty or damaged. Take out the disc, clean it and retry.
● An attempt has been made to record copy-protected contents.
● An attempt has been made to record copy-once contents on a
disc that is not CPRM compatible.
COPY PROHIBITED
CAN NOT PLAY
● The unit has detected invalid contents at the start or in the middle
of playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
EN
68
Language Code List
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
Afar
IN
Indonesian
Icelandic
Hebrew
RU
RW
SA
SD
SG
SH
SI
Russian
Kinyarwanda
Sanskrit
Sindhi
Abkhazian
Afrikaans
Ameharic
Arabic
IS
IW
JI
Yiddish
JW
KA
KK
KL
Javanese
Georgian
Kazakh
Sangho
Serbo-Croatian
Singhalese
Slovak
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SW
TA
KM
KN
KO
KS
KU
KY
LA
Slovenian
Samoan
Shona
Somali
Bislama
Bengali, Bangla
Tibetan
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
BN
BO
BR
CA
CO
CS
CY
DZ
EL
EO
ET
EU
FA
Kirghiz
Latin
Breton
LN
LO
LT
Lingala
Catalan
Corsican
Czech
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
LV
Welsh
MG
MI
TE
TG
TH
TI
Telugu
Bhutani
Greek
Tajik
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
OC
OM
OR
PA
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Thai
Esperanto
Estonian
Basque
Persian
Fiji
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
TK
TL
TN
TO
TR
TS
TT
FJ
Malay (MAY)
Maltese
FO
FY
GA
GD
GL
GN
GU
HA
HI
Faroese
Frisian
Turkish
Tsonga
Tatar
Burmese
Nauru
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Nepali
TW
UK
UR
UZ
VI
Twi
Occitan
Ukrainian
Urdu
(Afan) Oromo
Oriya
Uzbek
Panjabi
Vietnamese
Volapuk
Wolof
Hindi
PL
Polish
VO
WO
XH
YO
ZH
ZU
HR
HU
HY
IA
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
PS
PT
QU
RM
RN
RO
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Xhosa
Yoruba
Chinese
Zulu
IE
IK
Rumanian
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
EN
69
GENERAL
Input/Output
Power requirement
S-video input
AC 120 V H, 60 Hz
Y
C
: 1.0 Vp-p, 75 K
: 0.286 Vp-p, 75 K
Power consumption
Power on: 30 W
Power off: 2.7 W
S-video output
Y
C
: 1.0 Vp-p, 75 K
: 0.3 Vp-p, 75 K
Temperature
Operating: 5°C to 35°C (41°F to 95°F)
Storage: -20°C to 60°C (-4°F to 140°F)
Video input : 1.0 Vp-p, 75 K (pin jack)
Video output : 1.0 Vp-p, 75 K (pin jack)
Audio input : 2 Vrms (pin jack)
Operating position
Horizontal only
Audio output : 2 Vrms (pin jack)
i.Link
: 4-pin for DV input
Component video output
Dimensions (WxHxD)
Y
Pb/Pr
: 1.0 Vp-p, 75 K
: 0.7 Vp-p, 75 K
435 mm x 70 mm x 300 mm (17-3/16" x 2-11/16" x 11-13/16")
Weight
3.4 kg (7.5 lbs)
Corresponding to copy protection
Digital audio output
: Coaxial
VIDEO/AUDIO
Corresponding to Dolby Digital and DTS Digital
Surround
Bit stream
Recordable disc: DVD-RAM 12 cm (4.7 GB/9.4 GB)
DVD-RAM 8 cm (1.4 GB/2.8 GB)
Selectable in digital audio output setting menu
DVD-R 12 cm (4.7 GB)
DVD-R 8 cm (1.4 GB)
TUNER/TIMER
DVD-RW 12 cm (4.7 GB)
DVD-RW 8 cm (1.4 GB)
Tuning system : Frequency synthesizer tuner
Channel coverage
Recording format
VHF
UHF
CATV
: Channels 2 - 13
: Channels 14 - 69
: 113 Channels
DVD-RAM : DVD Video Recording format
DVD-R
DVD-RW
: DVD Video format
: DVD Video format, DVD Video Recording format
Clock reference : Quartz
Recording time
Program capacity
Maximum 8 hours (with 4.7 GB disc)
: 30 days programmable timer/8 programs
(XP)
(SP)
(LP)
(EP)
(FR)
: Approx. 1 hour
Memory backup time
: Approx. 5 sec.
: Approx. 2 hours
: Approx. 4 hours
: Approx. 6 hours
: Approx. 1 hour - 8 hours
ACCESSORIES
Provided accessories
Audio recording system
: Dolby Digital (2 ch)
Linear PCM (XP mode only)
Video recording compression system
: MPEG2 (CBR/VBR)
: RF cable,
Audio/video cable,
Infrared remote control unit,
“AA” battery x 2
Specifications shown are for SP mode unless otherwise specified.
E. & O.E. Design and specifications subject to change without
notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIST OF TERMS
70
EN
A
O
A-B Repeat Playback ................................................ 31
Adjusting The Picture Quality ..................................... 32
Angle Selection ........................................................ 25
Audio Language/Sound Selection ............................... 26
Auto Channel Set ..................................................... 20
Auto Clock ............................................................... 17
Auto Tuner Set ......................................................... 17
Automatic Satellite Program Recording ....................... 42
On-Screen Display .................................................... 15
P
Pan&Scan ................................................................ 21
Play List ................................................................... 47
Programs overlap ..................................................... 41
Progressive scan ...................................................... 60
C
Check, Cancel And Change Programs ........................ 41
Child Lock ............................................................... 61
D
R
Disc menu ............................................................... 23
Disc Remaining Time ................................................ 35
Disc Resume ........................................................... 60
Discs For Playback Only ............................................. 8
DV Dubbing ............................................................. 53
DVD menu ............................................................... 23
Random Playback ..................................................... 33
Recordable/Playable Discs .......................................... 7
Recording Medium And Format .................................... 9
Recording mode ....................................................... 34
E
Elapsed Recording Time Indication ............................ 35
F
S
File Structure Of Discs ................................................ 9
Finalize ................................................................... 64
Format disc .............................................................. 63
Frame-By-Frame Playback ........................................ 23
Free Rate Function ................................................... 36
Second Audio Recording ........................................... 36
Semiauto Clock Set .................................................. 19
Setting the Progressive Mode .................................... 32
Slow Motion ............................................................. 24
Still Picture ............................................................... 23
G
Guide Channel Number Set ....................................... 62
I
Instant Timer Recording (ITR) .................................... 35
Interlaced scan ......................................................... 60
T
L
Time Search ............................................................ 32
Language Code List .................................................. 68
Letter Box ................................................................ 21
Library Database Navigation ...................................... 43
Live Memory Playback .............................................. 27
U
M
V
Manual Channel Set ................................................. 20
Manual Clock Set ..................................................... 19
Manual Timer Programming ....................................... 38
Marking Positions To Play Back Again Later ................ 25
Menu/Audio/Subtitle Language Set ............................. 18
Monitor Set .............................................................. 21
VCR Plus+ Setting .................................................... 62
VCR Plus+ Timer Programming ................................. 37
Download from Www.Somanuals.com. All Manuals Search And Download.
|
