ENGLISH
DIGITAL HD PLAYER
GETTING STARTED
VIDEO PLAYBACK
11
18
22
28
CU-VH1
Please visit our Homepage on the World Wide
Web for Digital Video Camera:
For Accessories:
DIGITAL STILL CAMERA
(D.S.C.) PLAYBACK
ADVANCED FEATURES
REFERENCES
TERMS
44
61
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No. which is
located on the bottom of the player. Retain this
information for future reference.
Model No.
Serial No.
EN
LYT1221-001B
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
3
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides
to allow for ventilation (10 cm (3-15/16”) or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus.
When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or splashing.
Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
This product has a fluorescent lamp that contains a small amount of mercury. Disposal of these materials
may be regulated in your community due to environmental considerations.
For disposal or recycling information please contact your local authorities, or the Electronics Industries
Alliance:
<http://www.eiae.org>
Download from Www.Somanuals.com. All Manuals Search And Download.
4
EN
5. Ventilation
IMPORTANT PRODUCT SAFETY
INSTRUCTIONS
Electrical energy can perform many useful functions.
But improper use can result in potential electrical
shock or fire hazards. This product has been
engineered and manufactured to assure your
personal safety. In order not to defeat the built-in
safeguards, observe the following basic rules for its
installation, use and servicing.
Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation of the
product and to protect it from overheating, these
openings must not be blocked or covered.
● Do not block the openings by placing the product
on a bed, sofa, rug or other similar surface.
● Do not place the product in a built-in installation
such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s
instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
ATTENTION:
Follow and obey all warnings and instructions
marked on your product and its operating
instructions. For your safety, please read all the
safety and operating instructions before you operate
this product and keep this manual for future
reference.
ANTENNA INSTALLATION INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the product, be sure the antenna or cable system
is grounded so as to provide some protection against
voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode.
INSTALLATION
1. Grounding or Polarization
(A)Your product may be equipped with a polarized
alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature.
If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
2. Lightning
For added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due
to lightning and power-line surges.
(B)Your product may be equipped with a 3-wire
grounding-type plug, a plug having a third
(grounding) pin. This plug will only fit into a
grounding-type power outlet. This is a safety
feature.
3. Power Lines
If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding-type plug.
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to
keep from touching such power lines or circuits as
contact with them might be fatal.
2. Power Sources
Operate your product only from the type of power
source indicated on the marking label. If you are not
sure of the type of power supply to your home,
consult your product dealer or local power
company. If your product is intended to operate from
battery power, or other sources, refer to the
operating instructions.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
3. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in
a risk of fire or electric shock.
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION
4. Power Cord Protection
ELECTRIC SERVICE
EQUIPMENT
810-20)
Power supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles,
and the point where they exit from the product.
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
5
USE
SERVICING
1. Accessories
1. Servicing
To avoid personal injury:
If your product is not operating correctly or exhibits
a marked change in performance and you are
unable to restore normal operation by following the
detailed procedure in its operating instructions, do
not attempt to service it yourself as opening or
removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to
qualified service personnel.
● Do not place this product on an unstable cart,
stand, tripod, bracket or table. It may fall, causing
serious injury to a child or adult, and serious
damage to the product.
● Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer or sold
with the product.
● Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s
instructions for any mounting of the product.
● Do not try to roll a cart with small casters across
thresholds or deep-pile carpets.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or damaged in
any way.
2. Product and Cart Combination
A product and cart
PORTABLE CART WARNING
(Symbol provided by RETAC)
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may cause
the product and cart
combination to overturn.
3. Water and Moisture
Do not use this product near
water-for example, near a
bath tub, wash bowl, kitchen sink or laundry tub, in
a wet basement, or near a swimming pool and the
like.
f. When the product exhibits a distinct change in
performance-this indicates a need for service.
3. Replacement Parts
4. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any kind
on the product.
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or
other hazards.
5. Attachments
Do not use attachments not recommended by the
manufacturer of this product as they may cause
hazards.
4. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in safe
operating condition.
6. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
7. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
EN
SAFETY PRECAUTIONS
CAUTION!
The following notes concern possible physical damage to the player and to the user.
When carrying, be sure to always securely attach and use the provided strap. Carrying or holding the player
by the LCD monitor can result in dropping the unit, or in a malfunction.
Take care not to get your finger caught in the cassette holder cover. Do not let children operate the player, as
they are particularly susceptible to this type of injury.
CAUTION!
Connecting cables (S, audio/video, USB, etc.) to the player and leaving it on top of the TV is not
recommended, as tripping on the cables will cause the player to fall, resulting in damage.
Ⅲ This player is designed exclusively for the digital video cassette, SD Memory Card and MultiMediaCard.
Only cassettes marked “
with this unit.
” and memory cards marked “
” or “
” can be used
Before using the player…
… make sure you only use cassettes with the Mini DV mark
… make sure you only use memory cards with the mark
.
or
.
… remember that this player is not compatible with other digital video formats.
… remember that this player is intended for private consumer use only. Any commercial use without proper
permission is prohibited. (Even if you record an event such as a show, performance or exhibition for
personal enjoyment, it is strongly recommended that you obtain permission beforehand.)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
7
Provided Accessories
AC Power Adapter/
Charger AA-V40U
DC Cord
Battery Pack
BN-V416U
Audio/Video Cable
(RCA plug to RCA plug)
S-Video Cable
Component Video Cable
USB Cable
Audio Cable x 2
(for connection of
optional headphones
and external microphone
੬ pg. 9)
Shoulder Strap
(੬ pg. 9 for attachment)
RCA-BNC Adapter x 3
Remote Control Unit
RM-V718U
Lithium Battery CR2025*
(for remote control unit)
* A lithium battery is pre-
installed in the Remote
Control Unit at time of
shipment (with
insulation sheet). To use
the Remote Control
Unit, remove the
insulation sheet.
Core Filter
(੬ pg. 8 for attachment)
Connector Cover
•Large (A) x 2
•Large (B) x 1
•Medium x 2
•Small x 3
NOTES:
● In order to maintain optimum performance of the player, provided cables may be equipped with one or
more core filter. If a cable has only one core filter, the end that is closest to the filter should be connected to
the player.
● Make sure to use the provided cables for connections. Do not use any other cables.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
EN
3 Close the core filter until it clicks shut.
How To Attach The Core Filter
Attach the core filters to the cables. The core filter
reduces interference.
Types of core filters
Times to
Size
Cable
wind
Once
Audio/video cable
S-video cable
i.LINK cable*
USB cable**
Large (A)
NOTES:
● Take care not to damage the cable.
● When connecting a cable, attach the end with the
core filter to the player.
Large (B)
Medium
Twice
Once
DC cord
Audio cable
Small
Once
*
Optional
(If you have an optional JVC i.LINK cable
VC-VDV206U or VC-VDV204U with core
filters, it is not necessary to attach the provided
core filter. If you are going to use any other
i.LINK cable, attach the provided core filter.)
** Attach two core filters to both ends of the cable.
The procedure below is an example of winding
cable once.
1 Release the stoppers on both ends of the core
filter.
Stopper
2 Run the cable through the core filter, leaving
approx. 3 cm of cable between the cable plug
and the core filter. Wind the cable once around
the outside of the core filter as shown in the
illustration.
● Wind the cable so that it is not slack.
3 cm
Wind once.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
9
How To Attach The Strap
How To Use The Audio Cable
When using optional headphones or external
1 Thread the strap through the eyelet a.
microphone, connect to the provided audio cable
2 Fold it back and thread it through the strap guide
(with a core filter attached), then connect the audio
cable to the player. The core filter reduces
interference.
and the buckle.
● To adjust the length of the strap, loosen and
then tighten the strap in the buckle.
3 Repeat the procedure to attach the other end of
the strap to the other eyelet b.
Microphone
4 Confirm the strap is not twisted.
Eyelet b
Headphones
Audio cable
(provided)
Core filter
Strap guide
Eyelet a
Buckle
To
(headphones)
To MIC
How To Attach The Connector
Cover
Open the connector cover.
To protect the connectors, attach the provided
connector cover to the rear panel of the player when
the player is not in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
GETTING STARTED
EN
CONTENTS
Power .......................................................................11
Brightness Adjustment Of The Display ......................14
Date/Time Settings ....................................................15
Loading A Cassette
/Unloading A Cassette ..........................................16
Loading A Memory Card
/Unloading A Memory Card .................................17
DETAILS .................................................................... 44
TROUBLESHOOTING ................................................... 45
CAUTIONS ................................................................. 52
USER MAINTENANCE .................................................. 55
SPECIFICATIONS ........................................................ 56
INDEX ....................................................................... 58
TERMS
61
VIDEO PLAYBACK
18
Normal Playback ......................................................18
Still Playback ............................................................18
Frame-By-Frame Playback ........................................18
Shuttle Search ...........................................................19
Blank Search ............................................................19
DIGITAL STILL CAMERA (D.S.C.) PLAYBACK
Auto Playback Of Images .........................................22
Removing On-Screen Display ...................................23
Protecting Files .........................................................24
Resetting The File Name ...........................................26
Initializing A Memory Card ......................................27
ADVANCED FEATURES
MENUS FOR DETAILED ADJUSTMENT ...........................28
Changing The Menu Settings ....................................28
PLAYBACK MENUS .....................................................29
NAVIGATION............................................................. 32
NAVIGATION Function ...........................................32
DUBBING ..................................................................34
Dubbing To Or From A VCR ....................................34
Dubbing To Or From A Video Unit Equipped With
An i.LINK Connector (Digital Dubbing) ................35
Recording From The Middle Of A Tape ....................36
Dubbing Still Images Recorded On A Tape To
A Memory Card ....................................................38
USING THE REMOTE CONTROL UNIT ...........................39
Audio Dubbing (DV mode only) ...............................42
SYSTEM CONNECTIONS ..............................................43
Connection To A Personal Computer ........................43
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
11
● If the battery operation time remains extremely
short even after having been fully charged, the
battery is worn out and needs to be replaced.
Please purchase a new one.
Power
This player’s 2-way power supply system lets you
choose the most appropriate source of power. Do
not use provided power supply units with other
equipment.
● For other notes, ੬ pg. 44.
Using The Battery Pack
BATT.RELEASE
Switch
Charging The Battery Pack
Battery pack
BN-V416U or
BN-V428U
To AC outlet
POWER indicator
Arrow
AC Power Adapter/
Charger
1 With the arrow on the battery pack pointing to
the left, push the battery pack slightly against the
battery pack mount a.
CHARGE indicator
DC OUT connector
2 Slide the battery pack to the left until it locks in
1 Make sure you unplug the player’s DC cord from
place b.
the AC Power Adapter/Charger.
To detach the battery pack...
Slide the battery pack to the right slightly while
sliding BATT. RELEASE to detach it.
2 Plug the AC Power Adapter/Charger’s power cord
into an AC outlet. The POWER indicator lights.
3 Attach the battery pack with the YZ mark
aligned with the corresponding marks on the AC
Power Adapter/Charger. The CHARGE indicator
begins blinking to indicate charging has started.
NOTES:
● Available time is reduced significantly under the
following conditions:
• The LCD monitor is used repeatedly.
• The playback mode is engaged repeatedly.
● Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned recording time.
4 When the CHARGE indicator stops blinking but
stays lit, charging is finished. Remove the battery
pack.
5 Unplug the AC Power Adapter/Charger’s power
cord from the AC outlet.
ATTENTION:
Battery pack
Charging time
Before detaching the power source, make sure
that the player’s power is turned off. Failure to do
so can result in a player malfunction.
BN-V416U*
Approx. 2 hr.
BN-V428U
Provided
Approx. 3 hr. 20 min.
*
NOTES:
● If the protective cap is attached to the battery
pack, remove it first.
● If you connect the player’s DC cord to the AC
Power Adapter/Charger during battery charging,
power is supplied to the player and charging stops.
● Charging is not possible if the wrong type of
battery is used.
● When charging the battery pack for the first time
or after a long storage period, the CHARGE
indicator may not light. In this case, remove the
battery pack from the AC Power Adapter/Charger,
CONTINUED ON NEXT PAGE
then try charging again.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
EN
Using AC Power
About Batteries
Open the cover.
Mark
Lithium-ion is vulnerable in colder temperatures.
To DC connector
To AC outlet
Power cord
AC Power Adapter/
Charger
DANGER! Do not attempt to take the batteries apart,
or expose them to flame or excessive heat, as it may
cause a fire or explosion.
WARNING! Do not allow the battery or its terminals
a short circuit and possibly start a fire.
To DC OUT
connector
DC cord
1 Make sure you unplug the player’s DC cord from
the AC Power Adapter/Charger.
The Benefits Of Lithium-Ion Batteries
2 Connect the AC Power Adapter/Charger to the
Lithium-ion battery packs are small but have a large
power capacity. However, when one is exposed to
cold temperatures (below 10°C/50°F), its usage time
becomes shorter and it may cease to function. If this
happens, place the battery pack in your pocket or
other warm, protected place for a short time, then
re-attach it to the player. As long as the battery pack
itself is not cold, it should not affect performance.
(If you’re using a heating pad, make sure the battery
pack does not come in direct contact with it.)
player as shown in the illustration above.
NOTES:
● The provided AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
● For other notes, ੬ pg. 44.
For other notes, ੬ pg. 44.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
13
Playback Mode Switch Position
Operation Mode
To turn on the player, set the Power Switch to “ON”
while pressing down the Lock Button located on the
switch.
VIDEO:
Allows you to play back a tape.
MEMORY:
Allows you to play back images stored in a
memory card or access data stored in a memory
card.
Video Output Mode
Switch
Video Output Mode Switch Position
COMPONENT VIDEO OUT:
Allows you to output signals from the Component
Video connector. When you view images on the
connected TV, set the switch to this mode.
(੬ pg. 20)
Power Switch
LCD MONITOR:
When you view images on the player’s LCD
monitor or TV connected via video or S-video
cable, set the switch to this mode.
Playback Mode Switch
Lock Button
Choose the appropriate operation mode according
to your preference using Playback Mode Switch for
playback and Video Output Mode Switch for signal
output.
Power Switch Position
ON:
Allows you to switch on the player.
OFF:
Allows you to switch off the player.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
EN
LCD Monitor
Press the Monitor Opening Button and open the
LCD monitor fully.
To view images on the LCD monitor, set the Video
Output Mode Switch to “LCD MONITOR”.
(੬ pg. 13)
Brightness Adjustment Of The
Display
1 Set the Power Switch to “ON” while pressing
2 dOopwenn tthhee LLoCcDk mBuotntoitnorlofuclaltye.d on the switch.
3 Rotate the BRIGHT Wheel until the appropriate
brightness is reached.
BR I GHT
Monitor Opening Button
NOTES:
● The image on the LCD monitor and the image on
the TV screen may look differently in terms of the
brightness and color. Confirm the final image on
the TV screen.
● Colored bright spots may appear all over the LCD
monitor. However, this is not a malfunction.
(੬ pg. 47)
BRIGHT Wheel
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
15
1 Set the Power Switch to “ON” while pressing
Date/Time Settings
The date/time display can be turned on or off during
playback. (੬ pg. 28, 31)
down the Lock Button located on the switch.
2 Open the LCD monitor fully.
V I DEO
3 Press MENU. The Menu
SOUND MODE –STEREO
DV NARR .
REC MODE
–
–
OFF
Screen appears.
COPY– ON
R T Button
NAV I . DEL .
S / AV I NPUT
–
OFF
MENU Button
RETURN
DI SPLAY
4 Press R or T to select
“n” (DISPLAY), and press
MENU. The DISPLAY
Menu appears.
ON SCREEN
DATE / T I ME
T I ME CODE
CLOCK
–
–
–
LCD
OFF
OFF
DEC 2 5'0 3
5 : 3 0 PM
ADJ .
5 Press R or T to select
“CLOCK ADJ.”, and press
MENU. The parameter for
“Month” is highlighted.
RETURN
D I SPLAY
6 Press R or T to input the
month, and press MENU.
Repeat to input the day,
year, hour and minute.
Power Switch
CLOCK
ADJ .
DEC 2 5'0 3
5 : 3 0 PM
7 Press R or T to select
“BRETURN”, and press
MENU twice. The Menu
Screen closes.
RETURN
Download from Www.Somanuals.com. All Manuals Search And Download.
16
EN
Approximate recording time
Recording mode
SP LP
30 min. 45 min.
Loading A Cassette
/Unloading A Cassette
The player needs to be powered up to load or eject a
cassette
Tape
30 min.
60 min.
80 min.
60 min.
80 min.
90 min.
Cassette holder
120 min.
cover
PUSH HERE
To switch the recording mode, refer to pages 28 and
29.
OPEN/EJECT
Switch
NOTES:
● It takes a few seconds for the cassette holder to
open. Do not apply force.
● If you wait a few seconds and the cassette holder
does not open, close the cassette holder cover and
try again. If the cassette holder still does not open,
turn the player off then on again.
Cassette
holder
● If the tape does not load properly, open the
cassette holder cover fully and remove the
cassette. A few minutes later, insert it again.
● When the player is suddenly moved from a cold
place to a warm environment, wait a short time
cassette holder recedes may cause damage to the
player.
● Even when the player is switched off, a cassette
can be loaded or unloaded. After the cassette
holder is closed with the player switched off,
however, it may not recede. It is recommended to
turn the power on before loading or unloading.
● When resuming recording, once you open the
cassette holder cover a blank portion will be
recorded on the tape or a previously recorded
scene will be erased (recorded over) regardless of
whether the cassette holder came out or not. See
“Recording From The Middle Of A Tape”
(੬ pg. 36).
Make sure the
window side is
facing up.
Erase protection tab
1 Slide and hold OPEN/EJECT in the direction of
arrow, then pull the cassette holder cover open
until it locks. The cassette holder opens
automatically.
● Do not touch internal components.
2 Insert or remove a tape and press “PUSH HERE”
to close the cassette holder.
● Be sure to press only the section labeled
“PUSH HERE” to close the cassette holder;
touching other parts may cause your finger to
get caught in the cassette holder, resulting in
injury or product damage.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
● When the battery pack’s charge is low, you may
not be able to close the cassette holder cover.
Do not apply force. Replace the battery pack
with a fully charged one or use AC power
before continuing.
3 Close the cassette holder cover firmly until it
locks into place.
To protect valuable recordings…
Slide the erase protection tab on the back of the tape
in the direction of “SAVE”. This prevents the tape
from being recorded over. To record on this tape,
slide the tab back to “REC” before loading it.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
17
To protect valuable files (available only for SD
Memory Card)…
Loading A Memory Card
/Unloading A Memory Card
Write/erase protection tab
Card Cover
(MEMORY CARD)
Slide the write/erase protection tab on the side of the
memory card in the direction of “LOCK”. This
prevents the memory card from being recorded over.
To record on this memory card, slide the tab back to
the position opposite to “LOCK” before loading it.
Memory card
NOTES:
● Be sure to use only SD Memory Cards marked
“
“
” or MultiMediaCards marked
”.
Clipped edge
Label
● Some brands of memory cards are not compatible
with this player. Before purchasing a memory
card, consult its manufacturer or dealer.
● Before using a new memory card, it is necessary to
FORMAT the card. (੬ pg. 27)
1 Make sure the player’s power is off.
2 Slide to open the card cover (MEMORY CARD).
3 To load a memory card, firmly insert it with its
clipped edge first.
ATTENTION:
To unload a memory card, push it once. After the
memory card comes out of the player, pull it out.
● Do not touch the terminal on the reverse side
of the label.
Do not insert or remove the memory card while the
player is turned on, as this may cause the memory
card to be corrupted or cause the player to become
unable to recognize whether or not the card is
installed.
4 Close the card cover.
Information On SD Memory Card
SD Memory Cards up to 64 MB have been verified
for use with this player. (As of October 2003)
Download from Www.Somanuals.com. All Manuals Search And Download.
18
EN
VIDEO PLAYBACK
NOTES:
Normal Playback
● Clean the video heads using an optional dry
cleaning cassette when:
• No picture during playback.
• Blocks of noise appear during playback.
For details, ੬ pg. 53.
● If Stop mode continues for 5 minutes when power
is supplied from a battery, the player shuts off
automatically. To turn on again, set the Power
Switch to “OFF”, then “ON”.
BLANK SEARCH
Button
Fast-Forward Button (5)
Play/Pause Button (4/9)
VOLUME Wheel
Rewind Button (3)
Stop Button (8)
● The playback picture can be viewed in the LCD
monitor or on a connected TV. (੬ pg. 20)
● LCD monitor indications:
• When power is supplied from a battery: the
“
” battery indicator is displayed. (੬ pg. 49)
• When power is supplied from an AC outlet: the
” battery indicator does not appear.
“
● When a cable is connected to the S2, AUDIO (L/
R), VIDEO or headphone connector, sound cannot
be heard from the speaker.
Speaker
Playback Mode
Switch
To control the speaker volume…
Rotate the VOLUME Wheel towards “+” to turn up
the volume, or towards “–” to turn down the
volume.
Power Switch
1 Open the LCD monitor fully.
● Set the Video Output Mode Switch to “LCD
MONITOR”. (੬ pg. 13)
Still Playback
2 Load a cassette. (੬ pg. 16)
Pauses during video playback.
1) Press 4/9 during playback.
3 Set the Playback Mode Switch to “VIDEO”.
2) To resume normal playback, press 4/9 again.
● If still playback continues for more than about
3 minutes, the player’s Stop mode is
automatically engaged.
4 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
5 To start playback, press 4/9.
● When 4/9 is pressed, the image may not
pause immediately while the player stabilizes
the still image.
6 To stop playback, press 8.
● During Stop mode, press 3 to rewind, or
5 to fast-forward the tape.
Maximum continuous playback time
Frame-By-Frame Playback
Allows frame-by-frame search during video
playback. This feature is available only with a tape
recorded in DV recording mode.
1) Press 4/9 during playback.
2) Press R for forward and T for reverse.
Battery pack
BN-V416U*
BN-V428U
DV mode
1 hr. 40 min.
3 hr.
HD/SD mode
1 hr. 30 min.
2 hr. 50 min.
* Provided
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
19
NOTES:
Shuttle Search
● Before starting Blank Search, if the current position
is at a blank portion, the player searches in the
reverse direction. If the current position is at a
recorded portion, the player searches in the
forward direction.
● Blank Search does not work if “USE CLEANING
CASSETTE” has appeared with the tape.
● If the beginning or end of the tape is reached
during Blank Search, the player stops
automatically.
● A blank portion which is shorter than 5 seconds of
tape may not be detected.
● The detected blank portion may be located
between recorded scenes. Before you start
recording, make sure there is no recorded scene
after the blank portion.
Allows high-speed search in either direction during
video playback.
1) During playback, press 5 for forward search,
or 3 for reverse search.
2) To resume normal playback, press 4/9.
● During playback, press and hold 5 or 3.
The search continues as long as you hold the
button. Once you release the button, normal
playback resumes.
● A slight mosaic effect appears on the display
during Shuttle Search. This is not a
malfunction.
ATTENTION:
(DV mode only)
During Shuttle Search, parts of
the picture may not be clearly
visible, particularly on the left
side of the screen.
Slow-Motion Playback
Playback Zoom
Available only with the remote control (provided).
(੬ pg. 40, 41)
Blank Search
Helps you find where you should start recording in
the middle of a tape to avoid time code interruption.
(੬ pg. 36)
1 Load a cassette. (੬ pg. 16)
2 Set the Playback Mode Switch to “VIDEO”.
3 During Stop mode,
press BLANK
BLANK SEARCH
SEARCH.
PUSH "STOP" BUTTON
● The “BLANK
SEARCH”
TO CANCEL
indication appears
and the player
automatically starts
reverse or forward search, then stops at the
spot which is about 3 seconds of tape before
the beginning of the detected blank portion.
● To cancel Blank Search midway, press 8.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
EN
VIDEO PLAYBACK (cont.)
To Connect To A TV or VCR Equipped With The
Component Video Connectors
Connections To A TV Or VCR
These are some basic types of connections. When
making the connections, refer also to your VCR and
TV instruction manuals.
To Connect A Conventional TV or VCR
To Y/Pb/Pr
RCA-BNC
Adapter
COMPONENT
Y
Pb
Pr
VIDEO
OUT
COMPONENT
Y
Pb
Pr
VIDEO
OUT
S2
VIDEO
L
AUDIO
R
S2
VIDEO
L
AUDIO
R
To S2
To AUDIO/
VIDEO
To AUDIO
A
Audio/Video
cable
Audio/Video cable
(provided)
S-Video cable
(provided)
(provided)
Component video cable
(provided)
A
B
C
D
A
B C
VCR
D
Wide-screen TV or
high definition TV
A To S-VIDEO IN*
B Yellow to VIDEO IN**
C White to AUDIO L IN***
D Red to AUDIO R IN***
VCR
TV
A Not required for connection.
B White to AUDIO L IN*
C Red to AUDIO R IN*
D To component video connectors
*
Connect when your TV/VCR has S-VIDEO IN
and A/V input connectors. In this case, it is not
necessary to connect the yellow video cable.
** Connect when your TV/VCR has only A/V input
connectors.
*** Not required for watching still images only.
*
Not required for watching still images only.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
21
1 Make sure all units are turned off.
NOTES:
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the
battery pack. (੬ pg. 12)
2 Connect the player to a TV or VCR as shown in
the illustration.
If using a VCR, go to step 3.
If not, go to step 4.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the player is turned on.
● If you have a TV or speakers that are not specially
shielded, do not place the speakers adjacent to the
TV as interference will occur in the player
playback picture.
● During playback in HD mode, the images may not
appear on the player’s LCD monitor if the
component video cable is connected.
● When a cable is connected to the S2, AUDIO (L/
R), VIDEO or headphone connector, sound cannot
be heard from the speaker.
3 Connect the VCR output to the TV input,
referring to your VCR’s instruction manual.
4 For S-video or video connection
Set “S/VIDEO” to “16:9 TV” or “4:3 TV”
depending on the aspect ratio of the TV you are
connecting. (੬ pg. 28, 30)
● Set the Video Output Mode Switch to “LCD
MONITOR”.
For component video connection
● Set “Y/Pb/Pr” to any picture size depending on
the TV to which you are connecting.
(੬ pg. 28, 30)
● Set the Video Output Mode Switch to
“COMPONENT VIDEO OUT”.
● According to the type of the connected TV and the
recording mode, the playback picture may be
squeezed vertically or horizontally. For details,
refer to the Instructions of the TV.
6 Set the VCR to its AUX input mode, and set the
TV to appropriate input mode.
To choose whether or not the following displays
appear on the connected TV…
● Date/Time
Set “DATE/TIME” to “AUTO”, “ON” or “OFF”.
(੬ pg. 28, 31)
Or, press DISPLAY on the remote control to turn
on/off the date indication.
● Time Code
Set “TIME CODE” to “ON” or “OFF”.
(੬ pg. 28, 31)
● Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/TV”.
(੬ pg. 28, 31)
Download from Www.Somanuals.com. All Manuals Search And Download.
22
EN
D.S.C. PLAYBACK
NOTES:
Normal Playback Of Images
You can view the stored images in the memory card,
one at a time, much like flipping through a photo
album.
● Images shot in a file size other than “640 x 480”,
“848 x 480”, “1280 x 720” and “1280 x 960”
with another devices will be displayed thumbnail
images. These thumbnail images cannot be
transferred to a PC.
● Images shot with devices (such as JVC GR-
DVM70) that are not compatible with DCF cannot
FILE!” will be displayed.
Fast-Forward Button (5)
MENU Button/
R T Button
Play/Pause Button (4/9)
Rewind Button (3)
Playback Zoom
Stop Button (8)
Available only with the remote control (provided).
(੬ pg. 41)
You can run through all the images stored in
memory card automatically.
INDEX Button
1 Perform steps 1 – 4 in “Normal Playback Of
Playback Mode
Switch
INFO Button
Images”.
2 Press 4/9 to start Auto Playback. Files are
Power Switch
displayed in descending order.
● If you press 3 during Auto Playback, files
are displayed in ascending order.
1 Open the LCD monitor fully.
● Set the Video Output Mode Switch to “LCD
MONITOR”. (੬ pg. 13)
3 To end Auto Playback, press 8.
[For Normal Playback]
To display the next image
[For Auto Playback]
2 Load a memory card. (੬ pg. 17)
3 Set the Playback Mode Switch to “MEMORY”.
Image playback screen
4 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
● The still image which has been played back at
the last time is displayed.
100-0013
5 Press 3 to display the previous file. Press 5
100-0014
to display the next file.
● Pressing INFO gives you details on the
displayed file. (੬ pg. 23)
● You can also look for the desired file using
Index Screen. (੬ pg. 23)
100-0015
● You can turn off the on-screen playback
display. (੬ pg. 23)
100-0016
To display the previous image
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
23
Information Screen
Index Playback Of Files
You can view several different files stored in the
memory card at a time. This browsing capability
makes it easy to locate a particular file you want.
FOLDER
F I LE
: 1 0 0 JVCGR
: DVC0 0 0 1 0
03
DATE
:OCT 03
S I ZE
QUAL I TY : F I NE
PROTECT : OFF
: 1 2 8 0X7 2 0
1 Perform steps 1 – 4 in “Normal Playback Of
Images” (੬ pg. 22).
● Press the INFO Button again to close the
2 Press INDEX. The Index Screen of the image files
Information Screen.
appears.
NOTE:
Selected file
With images shot with other devices or processed on
a PC, “QUALITY: – – –” will be displayed.
Index number
Index Screen
1
4
7
2
5
8
3
Removing On-Screen Display
6
9
1 Perform steps 1 – 4 in “Normal Playback Of
Images” (੬ pg. 22).
2 Press MENU. The Menu Screen appears.
3 Press R or T to move the frame to the desired
file.
3 Press R or T to select “DISPLAY”, and press
MENU. The Sub Menu appears.
5 to display the next page.
The operation mode indicator, folder/file number
4 Press MENU. The selected file is displayed.
● Pressing INFO gives you details on the
displayed file. (See below.)
and battery indicator (
) disappear.
● To display the indicators again, select “ON”.
Operation mode indicator
Folder/file number
Viewing File Information
You can get the relevant file information by pressing
the INFO Button during normal playback or Index
Playback.
100-0013
MENU
D I SPLAY OFF
ON
FOLDER
FILE
DATE
SIZE
QUALITY
PROTECT
:
:
:
:
:
:
Folder name (੬ pg. 26)
File name (੬ pg. 26)
Date the file was made
Image size
Battery indicator
Picture quality
When set to “ON”, the file is
protected from accidental erasure.
(੬ pg. 24)
Download from Www.Somanuals.com. All Manuals Search And Download.
24
EN
D.S.C. PLAYBACK (cont.)
To protect the currently displayed file
Protecting Files
The Protect mode helps prevent the accidental
erasure of files.
7 Press R or T to select
MENU
“CURRENT”, and press
PROTECT
CURRENT
PROT . ALL
CANC . ALL
MENU. The PROTECT
screen appears.
RETURN
RT Button
Playback Mode
Switch
8 Press 3 or 5 to
select the desired file.
MENU Button
Rewind Button (3)
9 Press R or T to select
“EXECUTE”, and press
MENU.
PROTECT
PROTECTED
RETURN
● To cancel protection,
select “RETURN”.
all files you want to
protect.
To protect all files stored in the memory
card
7 Press R or T to select “PROT.ALL”, and press
MENU. The PROTECT screen appears.
Power Switch
Fast-Forward Button (5)
8 Press R or T to select “EXECUTE”, and press
MENU.
● To cancel protection, select “RETURN”.
1 Open the LCD monitor fully.
● Set the Video Output Mode Switch to “LCD
MONITOR”. (੬ pg. 13)
NOTES:
● If the “
” mark appears, the currently displayed
file is protected.
2 Load a memory card. (੬ pg. 17)
● When the memory card is initialized or corrupted,
even protected files are deleted. If you do not want
to lose important files, transfer them to a PC and
save them.
3 Set the Playback Mode Switch to “MEMORY”.
4 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
● The still image which has been played back at
the last time is displayed.
To Remove Protection
Before doing the following, perform steps 1 – 6 in
“Protecting Files” in the left column.
5 Press MENU. The Menu Screen appears.
6 Press R or T to select
MENU
“PROTECT”, and press
PROTECT
DELETE
MENU. The Sub Menu
DPOF
To remove protection from the currently
displayed file
NO . RESET
appears.
FORMAT
D I SPLAY
END
7 Press R or T to select “CURRENT”, and press
MENU. The PROTECT screen appears.
8 Press 3 or 5 to select the desired file.
9 Press R or T to select “EXECUTE”, and press
MENU.
● To cancel selection, select “RETURN”.
● Repeat steps 8 and 9 for all files you want to
remove protection.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
25
To remove protection from all files stored
in the memory card
To delete the currently displayed file
7 Press R or T to select
MENU
“CURRENT”, and press
7 Press R or T to select “CANC.ALL”, and press
DELETE
CURRENT
ALL
MENU. The DELETE
screen appears.
MENU. The PROTECT screen appears.
RETURN
8 Press R or T to select “EXECUTE”, and press
MENU.
8 Press 3 or 5 to
select the desired file.
● To cancel selection, select “RETURN”.
9 Press R or T to select
“EXECUTE”, and press
MENU.
DELETE
Deleting Files
Previously stored files can be deleted either one at a
time or all at once.
DELETE?
● To cancel deletion,
select “RETURN”.
● Repeat steps 8 and 9 for
all files you want to
delete.
EXECUTE
RETURN
RT Button
Playback Mode
Switch
NOTE:
MENU Button
Rewind Button (3)
If the “
” mark appears, the selected file is
protected and cannot be deleted.
To delete all files stored in the memory
card
7 Press R or T to select “ALL”, and press MENU.
The DELETE screen appears.
8 Press R or T to select “EXECUTE”, and press
MENU.
● To cancel deletion, select “RETURN”.
NOTES:
● Protected files (੬ pg. 24) cannot be deleted. To
delete them, remove protection first.
● Once files are deleted, they cannot be restored.
Check files before deleting.
Power Switch
Fast-Forward Button (5)
1 Open the LCD monitor fully.
● Set the Video Output Mode Switch to “LCD
MONITOR”. (੬ pg. 13)
CAUTION:
Do not remove the memory card or perform any
other operation (such as turning off the player)
during deletion. Also, be sure to use the provided
AC Power Adapter/Charger, as the memory card
may be corrupted if the battery becomes
exhausted during deletion. If the memory card
becomes corrupted, initialize it. (੬ pg. 27)
2 Load a memory card. (੬ pg. 17)
3 Set the Playback Mode Switch to “MEMORY”.
4 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
● The still image which has been played back at
the last time is displayed.
5 Press MENU. The Menu Screen appears.
6 Press R or T to select “DELETE”, and press
MENU. The Sub Menu appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
EN
Resetting The File Name
By resetting the file name, a new folder will be
made. The new files you are going to make will be
stored in the new folder. It is convenient to separate
the new files from previously made files.
Setting Print Information (DPOF
Setting)
This player is compatible with the DPOF (Digital
Print Order Format) standard in order to support
future systems such as automatic printing. You can
select one of the 2 print information settings for
images stored in the memory card: “To Print All Still
Images (One Print For Each)” or “To Print By
Selecting Still Images And Number Of Prints”.
1 Open the LCD monitor fully.
● Set the Video Output Mode Switch to “LCD
MONITOR”. (੬ pg. 13)
2 Load a memory card. (੬ pg. 17)
3 Set the Playback Mode Switch to “MEMORY”.
NOTES:
4 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
● The still image which has been played back at
the last time is displayed.
● If you load a memory card already set as shown
below in a printer compatible with DPOF, it will
make prints of the selected still images
automatically.
● To print images recorded on a tape, first dub them
to a memory card. (੬ pg. 38)
5 Press MENU. The Menu Screen appears.
6 Press R or T to select “NO. RESET”, and press
MENU. The NO. RESET screen appears.
To Print All Still Images (One Print For Each)
7 Press R or T to select “EXECUTE”, and press
MENU. The new folder (such as “101JVCGR”)
will be made and the file made of the next shot
starts from DVC00001.
1 Open the LCD monitor fully.
● Set the Video Output Mode Switch to “LCD
MONITOR”. (੬ pg. 13)
Folder and File names
2 Load a memory card. (੬ pg. 17)
Each time you dub still images recorded on a tape to
a memory card, a file name is made using a number
which is larger by one than the largest number of the
file names which are in use. Even if you delete an
image file with a number in the middle of range, the
number will not be used for a new shot; a gap will
remain in the numerical sequence. If the file name
reaches DVC09999, a new folder (such as
“101JVCGR”) will be made and the file name will
start again from DVC00001.
3 Set the Playback Mode Switch to “MEMORY”.
4 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
● The still image which has been played back at
the last time is displayed.
5 Press MENU. The Menu Screen appears.
6 Press R or T to select
MENU
“DPOF”, and press
DPOF
CURRENT
ALL
RESET
RETURN
MENU. The Sub Menu
1
appears.
7 Press R or T to select
“ALL 1”, and press MENU.
The DPOF screen appears.
8 Press R or T to select
“EXECUTE”, and press
MENU. The normal
DPOF
ALL1?
playback screen appears.
● To cancel selection,
select “RETURN”.
EXECUTE
RETURN
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
27
To Print By Selecting Still Images And Number
Of Prints
Initializing A Memory Card
You can initialize a memory card any time.
After initializing, all files and data stored in the
memory card, including those which have been
protected, are cleared.
1 Perform steps 1 – 6 in “To Print All Still Images
(One Print For Each)” (੬ pg. 26).
2 Press R or T to select
DPOF
“CURRENT”, and press
1 Open the LCD monitor fully.
● Set the Video Output Mode Switch to “LCD
MONITOR”. (੬ pg. 13)
MENU. The DPOF screen
appears.
SHEETS
0 0
RETURN
3 Press 3 or 5 to
2 Set the Playback Mode Switch to “MEMORY”.
select the desired file.
3 Set the Power Switch to “ON” while pressing
4 Press R or T to select the number indication
down the Lock Button located on the switch.
(00), and press MENU.
4 Press MENU. The Menu
MENU
5 Select the number of prints
DPOF
PROTECT
DELETE
DPOF
Screen appears.
by pressing R to increase
NO . RESET
FORMAT
D I SPLAY
number, or “T” to
SHEETS
decrease the number, and
0 5
END
press MENU.
● Repeat steps 3 through 5
for the desired number
of prints.
FORMAT
5 Press R or T to select
“FORMAT”, and press
ERASE ALL
EX I ST I NG DATA?
MENU. The FORMAT
screen appears.
● The number of prints can be set up to 15.
● To correct the number of prints, select the
image again and change the number.
EXECUTE
RETURN
6 Press R or T to select
“EXECUTE”, and press
6 Press R or T to select
DPOF
“RETURN”, and press
MENU. The “SAVE?”
appears.
● When initialization is finished, “NO IMAGES
STORED” appears.
● To cancel initialization, select “RETURN”.
SAVE?
EXECUTE
CANCEL
● If you did not change
any settings in step 3
through 5, the Menu
CAUTION:
Screen reappears.
Do not perform any other operation (such as
turning off the player) during initialization. Also,
be sure to use the provided AC Power Adapter/
Charger, as the memory card may be corrupted if
the battery becomes exhausted during
initialization.
7 Press R or T to select “EXECUTE” to save the
setting you have just made, and press MENU.
● To cancel selection, select “CANCEL”.
To Reset The Number Of Prints
1 Perform steps 1 – 6 in “To Print All Still Images
(One Print For Each)” (੬ pg. 26).
2 Press R or T to select “RESET”, and press
MENU. The DPOF screen appears.
3 Press R or T to select “EXECUTE”, and press
MENU. The normal playback screen appears.
● To cancel selection, select “RETURN”.
● The number of prints is reset to 0 for all still
images.
CAUTION:
While performing the above, never disconnect
power, as this may cause the memory card to be
corrupted.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
EN
MENUS FOR DETAILED ADJUSTMENT
Example: t VIDEO Menu
Changing The Menu Settings
Selected function
This player is equipped with an easy-to-use, on-
screen menu system that simplifies many of the
more detailed player settings. (੬ pg. 29 – 31)
V I DEO
Selected menu icon blinks.
SOUND MODE –STEREO
DV NARR .
REC MODE
–
–
OFF
COPY– ON
NAV I . DEL .
S / AV I NPUT
–
OFF
RT Button
RETURN
MENU Button
6 Press R or T to select the
Sub Menu
desired parameter.
V I DEO
SOUND MODE –STEREO
SOUNDL
SOUNDR
RETURN
V I DEO
7 Press MENU. Selection is
complete.
SOUND MODE –STEREO
DV NARR .
REC MODE
–
–
OFF
COPY– ON
you wish to set other
function menus.
NAV I . DEL .
S / AV I NPUT
–
OFF
Playback Mode
Switch
Power Switch
RETURN
8 Press MENU. The Menu
Screen returns.
1 Open the LCD monitor fully.
● Repeat the procedure if you wish to set other
● Set the Video Output Mode Switch to “LCD
MONITOR”. (੬ pg. 13)
function menus.
9 Press MENU again. The Menu Screen closes.
2 For Video Playback Menus:
1) Set the Playback Mode Switch to “VIDEO”.
2) Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
NOTES:
● The “n” (DISPLAY) settings are effective only for
video playback.
● The date indication can also be turned on/off by
pressing the DISPLAY Button on the remote
control (provided). (੬ pg. 21, 34)
For D.S.C. Playback Menus:
For details, refer to “D.S.C. PLAYBACK”
(੬ pg. 22).
V I DEO
3 Press MENU. The Menu
SOUND MODE –STEREO
DV NARR .
REC MODE
–
–
OFF
Screen appears.
COPY– ON
4 Press R or T to select the
desired function, and press
MENU. The selected
NAV I . DEL .
S / AV I NPUT
–
OFF
RETURN
function menu appears.
5 Press R or T to select the desired function, and
press MENU. The Sub Menu appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
29
PLAYBACK MENUS
Video Menu
VIDEO
Recording mode
Allows you to set the video recording mode (SP or
LP) depending on your preference. It is
recommended you use “REC MODE” in VIDEO
Menu when using this player as a recorder during
dubbing. (੬ pg. 34, 36)
Playback sound
REC MODE
SP / LP
(Factory-preset: SP)
During tape playback, the player detects the sound
mode in which the recording was made, and plays
the sound back. Select the type of sound to
Dubbing from tape to memory card
accompany your playback picture. According to the
menu access explanation on page 28, select
“SOUND MODE” or “DV NARR.” from the Menu
Screen and set it to the desired parameter.
COPY
(Factory-preset: ON)
OFF: When the SNAP SHOT button is pressed
during tape playback, the playback image pauses
and normal playback will resume after
approximately 6 seconds. (The still image is not
recorded.)
SOUND MODE
(Factory-preset: STEREO
: Sound is output from both “L” and
)
STEREO
“R” channels in stereo.
ON: Enables dubbing of images recorded on a
tape to a memory card. (੬ pg. 38)
SOUND L : Sound from the “L” channel is
output.
SOUND R : Sound from the “R” channel is
output.
Deleting thumbnail images
DV NARR.
(Factory-preset: OFF)
For details, refer to “To delete thumbnail images”
(੬ pg. 33).
OFF: Original sound is output from both “L” and
“R” channels in stereo.
NAVI.DEL.
ON: Dubbed sound is output from both “L” and
“R” channels in stereo.
IMAGE SEL. / TAPE SEL. / ALL / RETURN
MIX: Original and dubbed sounds are combined
and output in stereo on both “L” and “R”
channels.
S-Video/AV input
S/AV INPUT
(Factory-preset: OFF)
OFF: Enables audio and video signal output to a
TV, VCR, etc. via the AUDIO (L/R) and VIDEO or
AUDIO (L/R) and S2 connectors. (੬ pg. 20, 36)
ON: Enables audio and video signal input from
the AUDIO (L/R) and VIDEO connectors, or audio
and S-video signal input from the AUDIO (L/R)
and S2 connectors. (੬ pg. 34)
NOTES:
● The “SOUND MODE” setting is available for both
12-bit and 16-bit sound. (In previous models’
functions, “12-bit” is called “32 kHz” and “16-bit”
is called “48 kHz”.)
● The player cannot detect the sound mode in which
the recording was made during fast-forward or
rewind. During playback the sound mode is
displayed in the upper left corner.
NOTE:
When VIDEO and S2 connectors are simultaneously
connected, S-video signal is input from the S2
connector.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
EN
PLAYBACK MENUS (cont.)
S-Video output setting
System Menu
When connecting the player to a 4:3 TV or wide-
screen TV using the S-video cable (੬ pg. 20), select
the aspect ratio of the connected TV.
SYSTEM
(Factory-preset: 4:3 TV)
16:9 TV: For a TV which has an aspect ratio of
16:9.
Beep and melody sound
BEEP
(Factory-preset: OFF)
4:3 TV: For a TV which has an aspect ratio of 4:3.
OFF: The beep does not sound even when the
operation is performed.
BEEP: The beep sounds when the operation is
performed.
MELODY: Instead of a beep, a melody sounds
when any operation is performed.
i.LINK output setting
During digital tape dubbing, select whether the
video signal outputs according to the Switch setting.
i.LINK OUT
(Factory-preset: SW)
SW: Normally, set to this position. Outputs the DV
or MPEG2 format signal selected with the i.LINK
OUT Switch.
AUTO: For future use. If the connected video unit
automatically detects the input signal via an
i.LINK connector, set to “AUTO”.
Remote control setting
For details, refer to “USING THE REMOTE
CONTROL UNIT” (੬ pg. 39).
REMOTE
(Factory-preset: ON)
OFF: Disables the remote control operations.
ON: Enables the remote control operations.
Picture quality
The Picture Quality mode can be selected to best
match your needs. Two Picture Quality modes are
available: FINE (
of quality).
Component video output setting
) and STANDARD (
) (in order
When connecting the player to a TV or video unit
equipped with component video inputs (੬ pg. 20),
select the output picture size depending on the
connected TV or video unit.
QUALITY
(Factory-preset: FINE)
FINE / STANDARD
Y/Pb/Pr
(Factory-preset: NO CONV.)
NOTE:
NO CONV.: Outputs with the original size.
Signals are output in 480p during recording.
720 to 1080: Converts to 1080i. Signals are
output in 480p during recording.
ALL to 480p: Converts to 480p.
ALL to 480i: Converts to 480i.
ALL to 1080: Converts to 1080i. Select this setting
if your TV is compatible to 1080i input only.
Signals are not output during recording (in any
mode) or playback in DV mode.
The number of storable images depends on the
selected picture quality as well as the composition
of the subjects in the images and the type of memory
card being used.
Resetting menu settings
RESET
EXECUTE: Resets all settings to the factory-preset.
RETURN: Does not reset all settings to the factory-
preset.
NOTE:
Signals are output in 480i during recording or
playback in DV mode regardless of the output
setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
31
NOTE:
Display Menu
The date indication can also be turned on/off by
pressing the DISPLAY Button on the remote control
(provided). (੬ pg. 21, 34)
DISPLAY
Display
ON SCREEN Setting:
4
DV 12b i
L
t
/ NARR .
Display setting
ON SCREEN
OFF: The player’s display disappears.
For playback mode,
playback sound, tape
speed and tape running
during video playback.
(Factory-preset: LCD)
LCD: Keeps the player’s display (except the date,
time and time code) from appearing on the
connected TV screen.
LCD/TV: Makes the player’s display appear on
screen when the player is connected to a TV.
DATE/TIME Setting:
For date/time.
Date and time display setting
DATE/TIME
OFF: The date/time do not appear.
(Factory-preset: OFF)
DE
C
25 ' 03
5:30 PM
AUTO: The date/time are displayed in the
following cases:
•When playback starts. The player displays the
date/time when scenes are recorded.
•When the date is changed during playback.
TIME CODE Setting:
For time code.
Minutes
Seconds
Frames*
ON: The date/time are always displayed.
12 : 34 : 24
Time code setting
* 30 frames = 1 second
TIME CODE
(Factory-preset: OFF)
OFF: Time code is not displayed.
ON: Time code is displayed on the player and on
the connected TV. Frame numbers are not
displayed during recording.
Clock adjustment
CLOCK ADJ.
•Allows you to set the current date and time.
(੬ pg. 15)
Download from Www.Somanuals.com. All Manuals Search And Download.
32
EN
NAVIGATION
To add thumbnail images during video
NAVIGATION Function
The Navigation Function helps you check tape
contents by making thumbnail images on a memory
card.
playback
1 Perform steps 1 to 4 in “To find scenes on tape
using thumbnail images (NAVIGATION Search)”.
2 Press 4/9 to start video playback.
3 Press NAVI STORE at the desired point.
● The “ ” indicator appears briefly and the
image of the point where NAVI STORE is
pressed is stored in the memory card as a
thumbnail image.
RT Button
Fast-Forward
MENU Button
Button (5)
Play/Pause Button (4/9)
● If you use the tape recorded in SD or HD
mode, it will enter the playback pause mode.
To play, press 4/9.
Rewind Button (3)
Stop Button (8)
NAVI Button
NAVI STORE Button
Playback Mode
Switch
Power Switch
To find scenes on tape using thumbnail images
(NAVIGATION Search)
1 Load a cassette. (੬ pg. 16)
2 Load a memory card. (੬ pg. 17)
3 Set the Playback Mode switch to “VIDEO”.
4 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
5 Press NAVI during video playback or stop mode.
● The loaded cassette’s
NAVIGATION thumbnail
image screen appears.
NAV I GAT I ON
DATE :MAY 2 4 ’ 0 3
33 ::2 9 AM
TC
:
1 3 : 2 3 : 1 5
2
1
3
● Press 3 to display the
previous page. Press 5
to display the next page.
4
5
006
6 Press R or T to select the desired image, and
press MENU.
● The “NAVIGATION SEARCH” indication
appears blinking and the player starts searching
the tape for the relevant point of the selected
thumbnail image.
To cancel NAVIGATION search midway...
Press 8 or 4/9.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
33
IMPORTANT:
To delete thumbnail images
● Be sure to always use the same tape and memory
card together as they were during recording;
otherwise, the player cannot recognize Tape and
Memory Card IDs to perform NAVIGATION
function properly.
● Check if an appropriate tape and memory card are
loaded when the following messages appear:
“UNABLE TO USE NAVIGATION”, “THIS
MEMORY CARD IS NOT COMPATIBLE”.
● NAVIGATION Search does not work if the current
position is at a blank portion on the tape. Also, do
not leave a blank portion partway through the tape
when recording; otherwise, NAVIGATION
function does not work properly.
● Before recording newly over a recorded tape, be
sure to delete all thumbnail images of the previous
recording from the relevant memory card.
● If you copy thumbnail images from one memory
card to another via a PC, NAVIGATION Search
does not work with the copied memory card.
1 Load a memory card. (੬ pg. 17)
2 Set the Playback Mode switch to “VIDEO”.
3 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
4 Press MENU. The Menu Screen appears.
5 Press R or T to select “t” (VIDEO), and press
MENU. The VIDEO Menu appears.
V I DEO
6 Press R or T to select
SOUND MODE– STEREO
DV NARR .
REC MODE
–
–
OFF
“NAVI.DEL.”, and press
MENU. The Sub Menu
appears.
COPY– ON
NAV I . DEL .
S / AV I NPUT
–
OFF
7 By pressing R or T...
RETURN
Select “IMAGE SEL.” to
delete the currently displayed thumbnail image.
Select “TAPE SEL.” to delete all thumbnail images
for the tape which contains the currently
displayed image.
Select “ALL” to delete all thumbnail images
stored in the memory card at once.
NAV I GAT I ON
8 Press MENU. The
DELETE CURRENT?
NAVIGATION screen
appears.
9 Press R or T to select
“EXECUTE”, and press
MENU.
DEC 2 6 ’ 0 3
EXECUTE
RETURN
3 : 0 0PM
● Press 3 to display the previous page. Press
5 to display the next page.
● To cancel deletion, select “RETURN”.
● Thumbnail images cannot be deleted during
video playback.
CAUTION:
Do not remove the memory card or perform any
other operation (such as turning off the player)
during deletion. Also, be sure to use the provided
AC Power Adapter/Charger, as the memory card may
be corrupted if the battery becomes exhausted
during deletion. If the memory card becomes
corrupted, initialize it.
NOTE:
Once images are deleted, they cannot be restored.
Check images before deleting.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
EN
DUBBING
8 Press 4/9 on the player to start playback of the
Dubbing To Or From A VCR
source tape.
9 At the point you want to start dubbing, engage
the VCR’s Record mode.
10 To pause dubbing, engage the VCR’s Record-
Pause mode and press 4/9 on the player.
11 Repeat steps 8 – 10 for additional editing. Stop
the VCR and player.
NOTES:
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the
battery pack. (੬ pg. 12)
● As the player starts to play your footage, it will
appear on your TV. This will confirm the
connections and the AUX channel for dubbing
purposes.
COMPONENT
Y
Pb
Pr
VIDEO
OUT
S2
VIDEO
L
AUDIO
R
● Before you start dubbing, make sure that the
they do, they are being recorded onto the new
tape.
To S2
To AV
To choose whether or not the following displays
appear on the connected TV...
• Date/time
S-video cable
(provided)
Audio/video cable
(provided)
Set “DATE/TIME” to “AUTO”, “ON” or “OFF”.
(੬ pg. 28, 31) Or, press DISPLAY on the remote
control to turn on/off the date indication.
• Time code
Set “TIME CODE” to “OFF” or “ON”.
(੬ pg. 28, 31)
• Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/
1
2
3
4
TV
VCR
● Playback images recorded in HD or SD mode with
this player will be converted to DV format (480i)
image.
A To S-VIDEO* IN or OUT
B Yellow to VIDEO IN or OUT
C White to AUDIO L IN or OUT
D Red to AUDIO R IN or OUT
To use this player as a recorder
1) Perform steps 1 to 3 in the left column.
2) Set “S/AV INPUT” to “ON”. (੬ pg. 28, 29)
3) Set “REC MODE” to “SP” or “LP”. (੬ pg. 28, 29)
4) Insert the recording cassette in this player.
5) Press and hold REC (7), then press 4/9 to
*
Connect when your TV/VCR has an S-VIDEO
IN/OUT connector. In this case, it is not
necessary to connect the yellow video cable.
engage the Record-Pause mode. The “
indication appears on the screen.
6) Press 4/9 to start recording. The
rotates.
7) Press 8 to stop recording. The
stops rotating.
”
A/V in
indication
indication
To use this player as a player
1 Following the illustrations, connect the player
and the VCR. Also refer to page 20.
2 Set the player’s Playback Mode Switch to
“VIDEO”.
3 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
4 Turn on the VCR’s power.
5 Insert the source cassette in the player.
6 Insert the recording cassette in the VCR.
7 Engage the VCR’s AUX and Record-Pause modes.
● Refer to the instruction manual for the VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
35
NOTES:
NOTES:
● After dubbing, set “S/AV INPUT” back to “OFF”.
● Analog signals can be converted to digital signals
with this procedure.
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the
battery pack. (੬ pg. 12)
● It is also possible to dub from another player.
● Depending on the tape source input, images may
appear with horizontal jitter on the player’s LCD
monitor during dubbing. This does not affect the
actual recording.
● When using an i.LINK cable, be sure to use the
optional JVC VC-VDV204U i.LINK cable.
● If the remote control is used when both the player
and recorder are JVC video units, both units will
perform the same operation. To prevent this from
happening, press the buttons on both units.
● It is possible to dub in MPEG2 format from a
D-VHS VCR, if the source tape (D-VHS) has been
originally dubbed from this digital HD player or
digital HD video camera (ex. GR-HD1 or
JY-HD10) in MPEG2 format.
Dubbing To Or From A Video Unit
Equipped With An i.LINK
Connector (Digital Dubbing)
Using an i.LINK cable (optional), it is possible to dub
recorded scenes in DV format from the player onto
another video unit equipped with i.LINK connector.
Since a digital signal is sent, there is little if any
image or sound deterioration.
Images recorded in SD or HD mode can be dubbed
only to a D-VHS VCR with HS mode or digital HD
video camera (ex. GR-HD1 or JY-HD10).
To use this player as a player
1 Make sure all units are turned off.
2 Connect this player to a video unit equipped with
an i.LINK input connector using an i.LINK cable
as shown in the illustration.
3 Set this player’s Playback Mode Switch to
“VIDEO”.
4 Set “i.LINK OUT” to “SW”. (੬ pg. 28, 30)
● If, in future, the connected video unit
automatically detects the DV and MPEG2
formats, set “i.LINK OUT” to “AUTO”. In this
case, proceed to step 6.
DV MPEG2
i.LINK Output
Select Switch
I.LINK OUT
5 Set the i.LINK Output Select Switch on this player
to “DV” to output scenes recorded in DV mode,
or “MPEG2” to output scenes recorded in HD or
SD mode.
6 Turn on the video unit’s power.
7 Insert the source cassette in this player.
8 Insert the recording cassette in the video unit.
9 Press 4/9 on this player to start playback of the
To i.LINK Connector
source cassette.
10 At the point you want to start dubbing, engage
the video unit’s Record mode.
i.LINK cable
(optional)
11 To pause dubbing, engage the video unit’s
Record-Pause mode and press 4/9 on this
player.
12 Repeat steps 10 – 11 for additional editing.
Stop the video unit and player.
To i.LINK IN/OUT
NOTES:
● If a blank portion or disturbed image is played
back on the player during dubbing, unusual
images may be dubbed or the dubbing may stop.
● If a scene which has been paused during
recording is dubbed to other devices, playback
may stop at the point.
Video unit equipped
with i.LINK connector
● Do not connect the player through a hub.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
36
EN
DUBBING (cont.)
4) Set the i.LINK Output Select Switch on this player
to “DV” to output scenes recorded in DV mode,
or “MPEG2” to output scenes recorded in HD or
SD mode.
5) Connect the i.LINK cable again.
6) Start playback on this player, and then start
recording on the D-VHS VCR.
To use this player as a recorder
Dubbing from other devices in MPEG2 format is
possible if the connected device is another same
model of this unit. It is also possible to dub in
MPEG2 format from a D-VHS VCR, if the source
tape (D-VHS) has been originally dubbed from this
digital HD player in MPEG2 format.
● However, if signals on the D-VHS tape are
originally from an ATSC tuner etc., dubbing from a
D-VHS VCR in MPEG2 format is not possible.
Recording From The Middle Of A Tape
1) Play back a tape or use Blank Search (੬ pg. 19)
to find the spot at which you want to start
recording, then engage the Still Playback mode.
(੬ pg. 18)
1 Perform step 1 to 4 of “To use this player as a
player” (੬ pg. 35).
2 Set “REC MODE” to “SP” or “LP”. (੬ pg. 28, 29)
3 Turn on the video unit’s power.
NOTES:
4 Insert the source cassette in the video unit.
5 Insert the recording cassette in this player.
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time
code indication does not move smoothly.
● The time code is displayed only when “TIME
CODE” is set to “ON”. (੬ pg. 31)
6 Press and hold REC (7), then press 4/9 to
engage the Record Pause mode.
● The “
” indication appears on the
i.LINK in
screen.
When a blank portion is recorded on a tape
7 Press 4/9 again to start recording.
● The indication rotates.
Time code
00:00:00
Time code Time code
05:43:21 00:00:00
8 Press 4/9 again to engage the Record-Pause
mode.
● The
indication stops rotating.
Already
recorded scene
Newlyrecorded
scene
Blank
Tape
9 Repeat steps 7 – 8 for additional editing. Stop the
video unit and player.
Recording start Recording stop Recording start
NOTES:
DV to DV dubbing
point
point
point
● If a blank portion or disturbed image is played
back on the player during dubbing, unusual
images may be dubbed or the dubbing may stop.
Proper recording
MPEG2 to MPEG2 dubbing
Time code
00:00:00
Time code Time code
05:43:21 05:44:00
● It is not possible to dub signals in MPEG2 format
from devices other than D-VHS VCRs or another
same model of this player.
● MPEG2 signals that are copy-guarded may not be
recorded with this player.
Already
recorded scene
New
scene
Tape
Latest scene
● When dubbing MPEG2 video to the player, image
recording is performed properly.
Recording start Recording start
point point
Recording
start point
Notes on dubbing to a D-VHS VCR
Dubbing cannot be conducted properly when
dubbing a tape which is recorded in both DV and
HD (or SD) mode. In this case, perform the
following procedure.
1) Disconnect the i.LINK cable.
2) Reset the i.LINK device number on the D-VHS
VCR.
● For the operation, refer to the instruction
manual of the D-VHS VCR.
3) Set “i.LINK OUT” to “SW” on this player.
(੬ pg. 28, 30)
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording modes and features
Recording Mode
DV (480i):
The player records signals in the interlace scan
mode (half of 525 scanning lines at 1/60th of a
second).
The image will be recorded in an aspect ratio of 4:3.
The DV mode is suitable for playback on a
conventional 4:3-screen TV.
There are some features which are not available
depending on the recording mode.
Yes: Available
No: Not Available
Features
DV SD HD
Yes No No
Frame-By-Frame Playback
(੬ pg. 18)
SD (480p):
Slow-Motion Playback (੬ pg. 40) Yes No No
The player records signals in the progressive scan
mode (525 scanning lines at 1/60th a second at one
time).
Playback Zoom (੬ pg. 41)
Audio Dubbing (੬ pg. 42)
Yes No No
Yes No No
The SD mode reduces flickering more effectively
than a recording in DV mode.
The image will be recorded in an aspect ratio of
16:9. The SD mode is suitable for playback on a
wide-screen TV or high definition TV.
HD (720p):
The player records signals in the progressive scan
mode (750 scanning lines at 1/30th of a second for
recording and 1/60th of a second for playback at
one time).
The HD mode enables digital high definition
recording that offers higher picture quality than a
recording in SD or DV mode.
The image will be recorded in an aspect ratio of
16:9. The HD mode is suitable for playback on a
wide-screen TV or high definition TV.
Supported formats
Frames per sec.
Horizontal lines Vertical lines
Aspect ratio
Scan mode
Recording mode
(PB.)
1280
720
720
480
480
16:9
16:9
4:3
30
Progressive
Progressive
Interlaced
HD
SD
60
720
60
DV
Download from Www.Somanuals.com. All Manuals Search And Download.
38
EN
DUBBING (cont.)
Approximate Number of Storable Images
Dubbing Still Images Recorded On
A Tape To A Memory Card
Still images can be dubbed from a tape to a memory
card.
Image Size/Picture
Quality
SD Memory Card
8 MB 16 MB 32 MB 64 MB
640 x 480/FINE
30
80
25
66
10
26
68
178
55
144
376
117
313
48
297
772
241
643
99
640 x 480/
STANDARD
SNAP SHOT Button
RT Button
848 x 480/FINE
848 x 480/
STANDARD
148
22
MENU Button
1280 x 720/FINE
Play/Pause Button (4/9)
1280 x 720/
STANDARD
59
125
257
MultiMediaCard
Image Size/Picture Quality
8 MB 16 MB 32 MB
640 x 480/FINE
36
95
29
79
12
31
74
192
60
149
388
121
323
49
640 x 480/STANDARD
848 x 480/FINE
Playback Mode
848 x 480/STANDARD
1280 x 720/FINE
160
24
Switch
Power Switch
1280 x 720/STANDARD
64
129
1 Load a cassette. (੬ pg. 16)
2 Load a memory card. (੬ pg. 17)
3 Set the Playback Mode Switch to “VIDEO”.
4 Set the Power Switch to “ON” while pressing
down the Lock Button located on the switch.
5 Set “
COPY” to “ON”. (੬ pg. 28, 29)
6 Press 4/9 to start playback.
7 At the point you want to dub, press 4/9 again to
engage Still Playback.
8 To dub the image, press SNAP SHOT.
● The “
dubbing.
” indication appears during
● The selected image is stored in the memory
card.
NOTES:
● If SNAP SHOT is pressed in step 8 when a
memory card is not loaded, the message
“COPYING FAILED” is displayed.
● To use Playback Special effects with a video image
you wish to dub, perform up to step 8 using the
remote control (provided). (੬ pg. 41)
● Images are dubbed in the following image sizes:
Scenes recorded in HD mode: 1280 x 720 pixels
Scenes recorded in SD mode: 848 x 480 pixels
Scenes recorded in DV mode: 640 x 480 pixels
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
39
USING THE REMOTE CONTROL UNIT
The Full-Function Remote Control Unit can operate
this player from a distance. It also makes additional
playback functions possible. (੬ pg. 40, 41)
Buttons And Functions
Installing The Battery
The remote control uses one lithium battery
(CR2025).
1 Pull out the battery holder by inserting a pointed
instrument into the slot.
2 Insert the battery in the holder, and be sure to
have the “+” mark visible.
A Infrared beam transmitting window
B S.SHOT (Snapshot) Button*
3 Slide the holder back in until you hear a click.
C AUDIO Button ........................... (੬ pg. 28, 29)
D PAUSE Button* .................................. (੬ pg. 40)
Up Button* ....................................... (੬ pg. 41)
E SLOW Rewind Button ....................... (੬ pg. 40)
F REW Button*............................... (੬ pg. 19, 22)
Left Button ....................................... (੬ pg. 41)
G INSERT Button**
2
3
Slot
1
H STOP Button*.............................. (੬ pg. 18, 22)
I SHIFT Button .................................... (੬ pg. 41)
J START/STOP Button*
K EFFECT ON/OFF Button.................... (੬ pg. 41)
L EFFECT Button................................... (੬ pg. 41)
M SLOW Forward Button ...................... (੬ pg. 40)
N FF Button*................................... (੬ pg. 19, 22)
Right Button ..................................... (੬ pg. 41)
O PLAY Button*............................... (੬ pg. 18, 22)
P A. DUB Button.................................. (੬ pg. 42)
Q DISPLAY Button ......................... (੬ pg. 21, 34)
R Zoom (T/W) Buttons ........................ (੬ pg. 41)
1
Beam Effective Area (indoor use)
When using the remote
control, be sure to point it at
the remote sensor. The
transmitted beam’s
approximate effective
distance for indoor use is
Remote sensor
5 m (16 ft).
NOTE:
The transmitted beam may not be effective or may
cause incorrect operation when the remote sensor is
directly exposed to sunlight or powerful lighting.
*
Functions the same as each corresponding
button on the player. (੬ pg. 59)
** Unavailable with this player
Download from Www.Somanuals.com. All Manuals Search And Download.
40
EN
USING THE REMOTE CONTROL UNIT (cont.)
.
Frame-By-Frame Playback (DV mode only)
Allows frame-by-frame search during video
playback.
Up Button or
PAUSE
SLOW Forward
Button
SLOW Rewind
Button
During normal or still playback, press SLOW (IU)
repeatedly for forward or SLOW (YI) repeatedly for
reverse. Each time SLOW (YI or IU) is pressed, the
frame is played back.
Right Button
PLAY
Left Button
Down Button or
STOP
Zoom Buttons
SHIFT
Slow-Motion Playback (DV mode only)
Allows slow-speed search in either direction during
video playback.
During normal video playback, press SLOW (YI or
IU) more than approx. 2 seconds.
● After approx. 5 minutes (approx. 20 seconds with
an 80-minute cassette) in Slow Rewind or approx.
5 minutes in Slow Forward, normal playback
resumes.
● To pause Slow-Motion playback, press PAUSE (9).
● To stop Slow-Motion playback, press PLAY (U).
NOTES:
● You can also engage Slow-Motion Playback from
Still Playback by pressing SLOW (YI or IU) more
than approx. 2 seconds.
● During Slow-Motion Playback, due to digital
image processing, the picture may take on a
mosaic effect.
● After SLOW (YI or IU) is pressed and held, the still
image may be displayed for a few seconds,
followed by a blue screen for a few seconds. This
is not a malfunction.
● There may be a small margin between the slow-
motion playback start point you chose and the
actual start point for Slow-Motion Playback.
● During Slow-Motion Playback, there will be
disturbances in video and the picture may seem
unstable, especially with steady images. This is not
a malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
41
Playback Zoom (DV mode only)
Playback Special Effects (DV mode only)
Magnifies the recorded image up to 10X at any time
during video playback and D.S.C. playback.
1) Press PLAY (U) to start video
Allows you to add creative effects to the video
playback image that was recorded in DV mode.
The effects that can be used during playback are
CLASSIC FILM, MONOTONE, SEPIA and STROBE.
CLASSIC FILM: Gives recorded scenes a
strobe effect.
playback. Or perform normal
playback of images.
MONOTONE: Like classic black and white
2) At the point you want to zoom
in, press the Zoom Button (T).
● To zoom out, press the Zoom
Button (W).
films, your footage is shot in B/W.
SEPIA: Recorded scenes have a brownish tint
like old photos.
STROBE: Your recording looks like a series of
consecutive snapshots.
1) To start playback, press PLAY (U).
2) Press EFFECT. The PLAYBACK EFFECT Select
Menu appears.
3) Press EFFECT repeatedly to move the highlight
bar to the desired effect.
● The selected function is activated and after
2 seconds the menu disappears.
● To deactivate the selected effect, press EFFECT
ON/OFF. To reactivate the selected effect press
EFFECT ON/OFF again.
● To change the selected effect, repeat from
step 2 above.
3) You can move the image on the
screen around to find a particular
portion of the picture. While
holding down SHIFT, press L
(Left),
(Down).
(Right), U (Up) and E
● To end zoom, press and hold W until
magnification returns to normal. Or, press
STOP (8) and then press PLAY (U) during video
playback.
NOTES:
● Zoom can also be used during slow-motion and
still playback.
● Due to digital image processing, the quality of the
image may suffer.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
EN
USING THE REMOTE CONTROL UNIT (cont.)
NOTES:
Audio Dubbing (DV mode only)
The audio track of a tape recorded in DV format can
be customized only when recorded in the 12-bit and
SP modes. (੬ pg. 29)
● When editing onto a tape that was recorded at
12-bit, the old and new soundtracks are recorded
separately.
● If you dub onto a blank space on the tape, the
sound may be disrupted. Make sure you only edit
recorded areas.
Microphone
● If feedback or howling occurs during TV playback,
move the microphone away from the TV, or turn
down the TV’s volume.
● If you change from 12-bit to 16-bit in mid-
recording and then use the tape for Audio
Dubbing, it is not effective from the point where
16-bit recording began.
● During Audio Dubbing, when the tape moves to
scenes recorded in the LP mode, scenes recorded
in 16-bit audio or a blank portion, Audio Dubbing
stops.
● To perform Audio Dubbing while watching on the
television, make connections. (੬ pg. 20)
● To perform Audio Dubbing with a video unit
connected to the player’s S2, AUDIO(L/R), VIDEO
connector, first set “S/AV INPUT” to “ON” in
VIDEO Menu. (੬ pg. 28, 29)
The “AUX” indication appears instead of “MIC”.
However, you cannot hear the sound from the
connected device through the headphones.
Speaker
Audio
cable
(provided)
Open the cover.
1 Play back the tape to locate the point where
editing will start, then press PAUSE (9).
2 While holding A. DUB (D) on the remote
control, press PAUSE (9). The “9D” and “MIC”
indicators appear.
3 Press PLAY (U), then begin “narrating”. Speak
into the microphone.
● To pause dubbing, press PAUSE (9).
4 To end Audio Dubbing, press PAUSE (9), then
STOP (8).
To hear the dubbed sound during playback…
Set “DV NARR.” to “ON” or “MIX”. (੬ pg. 28, 29)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
43
SYSTEM CONNECTIONS
Connection To A Personal Computer
[A] Using USB cable
To USB connector
USB cable (provided)
PC
To USB
OR
[B] Using i.LINK cable
To i.LINK
connector
i.LINK cable
(optional)
PC with i.LINK
connector
To i.LINK
NOTES:
[A] Using USB cable
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the
battery pack. (੬ pg. 12)
It is possible to do the following things:
● Transfer still images stored on a memory card to a
PC.
● Never connect the USB cable and the i.LINK
cable simultaneously to the player. Connect only
the cable you wish to use to the player.
● Do not connect the player through a hub.
● When using an i.LINK cable, be sure to use the
optional JVC VC-VDV206U or VC-VDV204U
i.LINK cable depending on the type of i.LINK
connector (4 or 6 pins) on the PC.
● If the PC connected to the player via the USB
cable is not powered, the player does not enter the
USB mode.
● The date/time information cannot be captured into
the PC.
● Refer to the instruction manuals of the PC and
Software.
● The still images can also be transferred to a PC
with an i.LINK connector-equipped capture board.
● The system may not work properly depending on
the PC or capture board you are using.
System Requirements
● Windows®
OS: Windows® Me/2000/XP (pre-installed)
Connector: USB connector (standard equipment of
the computer)
PCs. Use the optional USB reader/writer CU-
VUSD70, the PC card adapter CU-VPSD60 or the
floppy disk adapter CU-VFSD50.
● Macintosh
OS: Mac OS 9.0.4 to 9.2.2
Mac OS X 10.1.5/10.2.1 to 10.2.8/ 10.3.1 to 10.3.2
Connector: USB connector (standard equipment of
the computer)
[B] Using i.LINK cable
It is also possible to transfer still/moving images to a
PC with an i.LINK connector by using the software
equipped with the PC or commercially available
software.
“USB MODE” and/or “ACCESSING FILES”
appears on the LCD monitor while the PC is
accessing data in the player or the player is
transferring a file to the PC.
NEVER disconnect the USB cable while
“ACCESSING FILES” is displayed on the LCD
monitor since this can result in product damage.
● Set “i.LINK OUT” to “SW”. (੬ pg. 30)
●
Set the i.Link Output Select Switch on this player to
the appropriate mode (
੬
pg. 35);
“DV”: when using the DV editing software
“MPEG2”: when using the MPEG2 editing software
● Set the i.Link Output Select Switch to the appro-
priate mode before connecting the i.Link cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
44
EN
DETAILS
ITEMS
NOTES
V Power (੬ pg. 11)
● Perform charging where the temperature is between 10°C and 35°C (50°F and
95°F). 20°C to 25°C (68°F to 77°F) is the ideal temperature range for charging. If
the environment is too cold, charging may be incomplete.
● Charging times are for a fully discharged battery pack.
● Charging time varies according to the ambient temperature and the status of the
battery pack.
● To avoid interference with reception, do not use the AC Power Adapter/Charger
near a radio.
● Since the AC Power Adapter/Charger processes electricity internally, it becomes
warm during use. Be sure to use it only in well-ventilated areas.
V VIDEO PLAYBACK ● When you use the LCD monitor outdoors in direct sunlight, the LCD monitor may
(੬ pg. 18)
be difficult to see.
● The cassette holder cannot be opened unless a power supply is attached.
● There may be a delay after you open the cassette holder cover until the cassette
holder opens. Do not use force.
● Once the cassette holder is closed, it recedes automatically. Wait until it recedes
completely before closing the cassette holder cover.
● “TAPE END” appears when the tape reaches its end, and the power goes off
automatically if left in this condition for 5 minutes. “TAPE END” also appears
when a cassette at its end is loaded.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
45
TROUBLESHOOTING
If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer.
The player is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.)
might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack,
AC Power Adapter/Charger, etc.) and wait a few minutes; and then re-connect it and proceed as usual from
the beginning.
Power
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
1. No power is supplied.
1. •The power is not connected 1. •Connect the AC Power
properly.
Adapter/Charger securely.
(੬ pg. 12)
•The battery is dead.
•Replace the dead battery
with a fully charged one.
(੬ pg. 11, 12)
Video and D.S.C. Playback
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
2. Play, Rewind and Fast-Forward 2. •The Playback Mode Switch is 2. •Set the Playback Mode
functions do not work.
set to “MEMORY”.
Switch to “VIDEO”.
3. The tape is moving, but there is 3. •Your TV has AV input
3. •Set the TV to the mode or
channel appropriate for
video playback. (੬ pg. 20)
•Close the cassette holder
cover. (੬ pg. 16)
no picture.
terminals, but is not set to its
VIDEO mode.
•The cassette holder cover is
open.
4. Blocks of noise appear during 4.
playback, or there is no
•
—
4. •Clean the video heads with
an optional cleaning
cassette.
•The tape is recorded in LP
mode.
playback picture and the
screen becomes blue.
•This is not a malfunction.
5. A memory card cannot be
5. •The Playback Mode Switch is 5. •Set the Playback Mode
set to “VIDEO”. Switch to “MEMORY”.
played back.
6. The image on the 4:3 TV is
6. •This occurs during recording 6. •This is not a malfunction.
elongated vertically (squeeze).
in HD or SD mode when a
tape (its erase protection tab
is set to “REC”) is loaded.
•The component video cable
and S-video or audio/video
cable are connected
•Disconnect either of two
cables.
simultaneously.
7. The screen of the LCD monitor 7. •The S-Video or audio/video 7. •This is not a malfunction.
is blackened or blocks of noise
appear on its right side but 4/
9 is not pressed.
cable is connected and “S/AV
INPUT” (੬ pg. 29) is set to
“ON”.
After dubbing, set “S/AV
INPUT” back to “OFF”.
8. When the screen is under
direct sunlight, the screen
becomes red or black for an
instant.
8. •This is not a malfunction.
8.
—
Download from Www.Somanuals.com. All Manuals Search And Download.
46
EN
TROUBLESHOOTING (cont.)
Advanced features
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
9. During recording, the date/
9. •“DATE/TIME” is set to “OFF”. 9. •Set “DATE/TIME” to “ON”.
(੬ pg. 28, 31)
time does not appear.
10. During recording, sound
10. •The optional headphones are 10. •Connect the optional
cannot be heard.
not connected to the
headphones to the
headphone connector.
(੬ pg. 59)
headphones connector.
11. Cannot record signals from a 11. •The connected device is not 11. •Dubbing from other devices
device which is connected to
the i.LINK connector.
compatible with this player.
in MPEG2 format is possible
if the connected device is
another same model of this
unit. It is also possible to dub
in MPEG2 format from a D-
VHS VCR, if the source tape
(D-VHS) has been originally
dubbed from this digital HD
player in MPEG2 format.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
47
Other problems
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
12. The CHARGE indicator on the 12. •The temperature of the
12. •To protect the battery, it is
recommended to charge it in
places with a temperature of
10°C to 35°C (50°F to 95°F).
(੬ pg. 52)
AC Power Adapter/Charger
does not light.
battery is extremely high/low.
•Charging is difficult in places
subject to extremely high/
low temperatures.
13. “SET DATE/TIME!” appears.
14. There is no picture.
13. •The built-in clock’s battery
has run out.
13. •Consult your nearest JVC
dealer for replacement.
•The previously set date/time
is erased.
14. •The player is not getting
power, or some other
malfunction exists.
14. •Turn the player’s power off
and on again. (੬ pg. 13)
15. Files stored in the memory
15. •Files stored in the memory
15. •Remove protection from the
card and delete them.
card cannot be deleted.
card are protected.
(੬ pg. 24 – 25)
16. When the player is connected 16. •The i.LINK cable was
16. •Turn the player’s power off
via the i.LINK connector, the
player does not operate.
plugged/unplugged with
power turned on.
and on again, then operate it.
17. The rear of the LCD monitor is 17. •The light used to illuminate 17. •Close the LCD monitor to
hot.
the LCD monitor causes it to
become hot.
turn it off or set the Power
Switch to “OFF”, and let the
unit cool down.
18. Images on the LCD monitor
18. •In places subject to low
temperature, images become
dark due to the
18. •Adjust the brightness and
angle of the LCD monitor.
(੬ pg. 14)
appear dark or whitish.
characteristics of the LCD
monitor. When this happens,
the displayed colors differ
from those that are actually
recorded. This is not a defect
of the player.
•When the LCD monitor’s
fluorescent light reaches the
end of its service life, images
on the LCD monitor become
dark. Consult your nearest
JVC dealer.
19. Colored bright spots appear all 19. •The LCD monitor is made
19.
over the LCD monitor.
with high-precision
technology. However, black
spots or bright spots of light
(red, green or blue) may
appear constantly on the
LCD monitor.
—
These spots are not recorded
on the tape. This is not due to
any defect of the unit.
(Effective dots: more than
99.99 %)
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
48
EN
TROUBLESHOOTING (cont.)
20. The indicators and the image 20. •This may occur when the
20.
color on the LCD monitor are
not clear.
surface or the edge of the
LCD monitor is pressed.
—
21. The cassette will not load
21. •The battery’s charge is low.
21. •Install a fully charged battery.
(੬ pg. 11, 12)
properly.
22. The memory card cannot be
22.
few more times. (੬ pg. 17)
—
removed from the player.
23. Picture does not appear on the 23. •The LCD monitor’s brightness 23. •Adjust the brightness of the
LCD monitor.
setting is too dark.
LCD monitor. (੬ pg. 14)
24. Images on the LCD monitor
24. •The speaker volume is too
24. •Turn the speaker volume
down. (੬ pg. 18)
are jittery.
great.
25. The LCD monitor has become 25.
25. •Wipe them gently with soft
cloth. Wiping strongly can
cause damage. (੬ pg. 55)
dirty (ex. fingerprints).
—
26. Time code does not appear.
26. •“TIME CODE” is set to
26. •Set “TIME CODE” to “ON”.
(੬ pg. 28, 31)
“OFF”.
27. An error indication (E01, E02 27. •A malfunction of some kind 27. •੬ pg. 51.
or E06) appears.
has occurred. In this case the
player’s functions become
unusable.
28. An error indication (E03 or
28. •A malfunction of some kind 28. •੬ pg. 51.
has occurred. In this case the
player’s functions become
E04) appears.
unusable.
29. The remote control does not
29. •“REMOTE” is set to “OFF”.
•The remote control does not
point at the remote sensor.
•The remote control batteries
are exhausted.
29. •Set “REMOTE” to “ON”.
work.
(੬ pg. 28, 30)
•Point at the remote sensor.
(੬ pg. 39)
•Replace the batteries with
fresh ones. (੬ pg. 39)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
49
Warning Indications
Indications
Meaning
Displays the battery remaining power.
Remaining power level: high
Remaining power level: exhausted
As the battery power comes close to nil, the battery indicator blinks.
When the battery power is exhausted, power turns off automatically.
Appears when no tape is loaded.
(੬ pg. 16)
CHECK TAPE’S ERASE Appears if the erase protection tab is set to “SAVE” when the REC (7) Button is
PROTECTION TAB
pressed when dubbing.
Appears if dirt is detected on the heads during recording. Use an optional
cleaning cassette.
USE CLEANING
CASSETTE
Appears if condensation occurs. When this indication is displayed, wait more
than 1 hour until condensation disappears.
CONDENSATION
OPERATION PAUSED
PLEASE WAIT
Appears if a tape is not loaded when the REC (7) Button is pressed when
dubbing.
TAPE!
TAPE END
Appears when the tape ends during recording or playback.
(੬ pg. 44)
CAN NOT PLAY BACK Appears when you attempt to play back a tape that is not compatible with this
THIS TAPE
player.
CAN NOT DISPLAY
ON LCD MONITOR
IN THIS MODE
Appears when dubbing a scene recorded in HD mode through the component
video connectors.
(੬ pg. 35)
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
50
EN
TROUBLESHOOTING (cont.)
Warning Indications
Indications
Meaning
i.LINK CONNECTION Appears when an i.LINK cable is connected but not detected. Disconnect the
ERROR! CHECK
CABLE CONNECTION
cable once and connect it again, or disconnect other connected cables.
(੬ pg. 35)
TO CHANGE i.LINK
OUTPUT SETTING,
DISCONNECT i.LINK
CABLE, FIRST
Appears when you attempt to change the i.LINK output mode while an i.LINK
cable is connected. (੬ pg. 35)
INVALID DATA!
CAN NOT INPUT
Appears when you attempt to dub signals which are copygurded or not
compatible with this player through an i.LINK cable.
COPYPROTECTED
CAN NOT INPUT
CAN NOT DECODE
VIDEO OR AUDIO
A. DUB ERROR!
Appears if Audio Dubbing is attempted on a blank portion of a tape. (੬ pg. 42)
A. DUB ERROR!
● Appears if Audio Dubbing is attempted on a tape recorded in SD or HD mode.
(੬ pg. 42)
<MPEG2 RECORDED>
<CANNOT DUB ON A ● Appears if Audio Dubbing is attempted on a tape recorded in the LP mode.
LP RECORDED TAPE>
(੬ pg. 42)
<CANNOT DUB ON A ● Appears if Audio Dubbing is attempted on a tape recorded in 16-bit audio.
16bit RECORDING>
<CHECK TAPE’S
ERASE PROTECTION
TAB>
(੬ pg. 42)
● Appears if A. DUB (D) on the remote control is pressed when the erase
protection tab is set to “SAVE”. (੬ pg. 42)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
51
Warning Indications
Indications
Meaning
● Appears if dubbing of copyguarded signals is attempted while this player is
being used as a recorder.
● Appears in the following cases when dubbing still images from a tape to a
memory card:
– when no memory card is loaded.
COPYING FAILED
– when the memory card’s memory is full.
– when the memory card is not formatted.
– when a write-protected SD Memory Card is loaded.
(੬ pg. 38)
Appears if there is no memory card loaded when you attempt to access data on a
memory card.
MEMORY CARD!
PLEASE FORMAT
NO IMAGES STORED
Appears when there is a problem with a memory card and its memory is corrupt,
or it has not been initialized. Initialize the memory card.
(੬ pg. 27)
Appears if there are no image files stored in the memory card when you attempt
memory card playback.
Appears when the player does not recognize the loaded memory card. Remove
the memory card once and insert it again. Repeat these procedures until no
indication appears. If the indication still appears, the memory card is corrupted.
CARD ERROR!
Appears when playing back a file that is not compatible with DCF or a file with a
size that is not compatible with this player.
UNSUPPORTED FILE!
● Appears when you attempt to dub digital still images when the write protection
CHECK CARD’S WRITE
tab on the SD Memory Card is set to the “LOCK” position.
PROTECTION SWITCH ● Appears when you attempt MEMORY SELECT menu operation with a write-
protected SD Memory Card loaded.
The error indications (E01, E02 or E06) show what type of malfunction has
E01, E02 or E06
occurred. When an error indication appears, the player turns off automatically.
UNIT IN SAFEGUARD
Remove the power supply (battery, etc.) and wait a few minutes for the indication
MODE REMOVE AND
to clear. When it does, you can resume using the player. If the indication remains,
REATTACH BATTERY
consult your nearest JVC dealer.
The error indications (E03 or E04) show what type of malfunction has occurred.
E03 or E04
When an error indication appears, the player turns off automatically. Eject the
UNIT IN SAFEGUARD
cassette once and re-insert it, then check if the indication clears. When it does,
MODE EJECT AND
REINSERT TAPE
you can resume using the player. If the indication remains, consult your nearest
JVC dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
EN
CAUTIONS
When using the AC Power Adapter/Charger in areas
other than the USA
chemical reaction, while warmer
temperatures can prevent complete charging.
... store in a cool, dry place. Extended exposure
to high temperatures will increase natural
discharge and shorten service life.
Ⅲ The provided AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to an AC
wall outlet other than American National Standard
C73 series type use an AC plug adapter, called a
“Siemens Plug”, as shown.
For this AC plug adapter, consult your nearest JVC
dealer.
... fully charge and then fully discharge the
battery every 6 months when storing the
battery pack over a long period time.
... remove from charger or powered unit when
not in use, as some machines use current even
when switched off.
NOTES:
Plug adapter
● It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
Charging........10°C to 35°C (50°F to 95°F)
Operation......0°C to 40°C (32°F to 104°F)
Storage ..........–20°C to 50°C (–4°F to 122°F)
● Recharging time is based on room temperature of
20°C (68°F).
Caution on Replaceable lithium battery
● The lower the temperature, the longer recharging
takes.
The battery used in this device may present a fire or
chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C
(212°F) or incinerate.
Replace battery with Panasonic (Matsushita Electric),
Sanyo, Sony or Maxell CR2025.
Danger of explosion or Risk of fire if the battery is
incorrectly replaced.
•Dispose of used battery promptly.
•Keep away from children.
•Do not disassemble and do not dispose of in fire.
Cassettes
To properly use and store your cassettes, be sure to
read the following cautions:
1. During use…
... make sure the cassette bears the Mini DV
mark.
... be aware that recording onto prerecorded
tapes automatically erases the previously
recorded video and audio signals.
... make sure the cassette is positioned properly
when inserting.
... do not load and unload the cassette
repeatedly without allowing the tape to run at
all. This slackens the tape and can result in
damage.
Battery Packs
The supplied battery pack
is a lithium-ion battery.
Before using the supplied
battery pack or an
optional battery pack, be
sure to read the following
... do not open the front tape cover. This exposes
the tape to fingerprints and dust.
2. Store cassettes…
Terminals
cautions:
1. To avoid hazards…
... away from heaters or other heat sources.
... out of direct sunlight.
... where they won’t be subject to unnecessary
shock or vibration.
... where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
... vertically, in their original cases.
... do not burn.
... do not short-circuit the terminals. When
transporting, make sure the provided battery
cap is attached to the battery. If the battery cap
is misplaced, carry the battery in a plastic bag.
... do not modify or disassemble.
... do not expose the battery to temperatures
exceeding 60°C (140°F), as this may cause the
battery to overheat, explode or catch fire.
... use only specified chargers.
2. To prevent damage and prolong service life…
... do not subject to unnecessary shock.
... charge in an environment where temperatures
are within the tolerances shown in the chart
below. This is a chemical reaction type
battery — cooler temperatures impede
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
53
... in places subject to soot or steam such as near
a cooking stove.
... in places subject to excessive shock or
vibration.
... near a television set.
... near appliances generating strong magnetic or
electric fields (speakers, broadcasting
antennas, etc.).
... in places subject to extremely high (over 40°C
or 104°F) or extremely low (under 0°C or
32°F) temperatures.
Memory Cards
To properly use and store your memory cards, be
sure to read the following cautions:
1. During use…
... make sure the memory card bears the SD or
MultiMediaCard mark.
... make sure the memory card is positioned
properly when inserting.
2. While the memory card is being accessed
(during recording, playback, deletion,
initialization, etc.)…
... never unload the memory card and never turn
off the player.
3. Store memory cards…
3. DO NOT leave the unit…
... in places of over 50°C (122°F).
... in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
... in direct sunlight.
... in a closed car in summer.
... near a heater.
... away from heaters or other heat sources.
... out of direct sunlight.
... where they won’t be subject to unnecessary
shock or vibration.
... where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
4. To protect the unit, DO NOT…
... allow it to become wet.
... drop the unit or strike it against hard objects.
... subject it to shock or excessive vibration
during transportation.
... carry it by holding the LCD monitor.
... swing it excessively when using the shoulder
strap.
LCD Monitor
1. To prevent damage to the LCD monitor,
DO NOT…
5. Dirty heads can cause the following problems:
... push it strongly or apply any shocks.
... place the player with the LCD monitor on the
bottom.
2. To prolong service life…
... avoid rubbing it with coarse cloth.
3. Be aware of the following phenomena for LCD
monitor use.
•No picture during playback.
•Blocks of noise appear during playback.
•During playback, the Head Clog Warning indicator
These are not malfunctions:
•While using the player, the surface around the
LCD monitor and/or the back of the LCD
monitor may heat up.
•If you leave power on for a long time, the
surface around the LCD monitor becomes hot.
“
” appears.
In such cases, use an optional cleaning cassette.
Insert it and play back. If the cassette is used more
than once consecutively, damage to the video heads
may result. After the player plays back for about 20
seconds, it stops automatically. Also refer to the
cleaning cassette’s instructions.
Main Unit
1. For safety, DO NOT…
If, after using the cleaning cassette, the problems still
exist, consult your nearest JVC dealer.
... open the player’s chassis.
... disassemble or modify the unit.
... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not
in use.
Mechanical moving parts used to move the video
heads and video tape tend to become dirty and
worn out over time. In order to maintain a clear
picture at all times, periodic check-ups are
recommended after using the unit for about 1,000
hours. For periodic check-ups please consult your
nearest JVC dealer.
... allow inflammables, water or metallic objects
to enter the unit.
... remove the battery pack or disconnect the
power supply while the power is on.
... leave the battery pack attached when the
player is not in use.
2. Avoid using the unit…
... in places subject to excessive humidity or
dust.
CONTINUED ON NEXT PAGE
Download from Www.Somanuals.com. All Manuals Search And Download.
54
EN
CAUTIONS (cont.)
About moisture condensation...
Declaration of Conformity
● You have observed that pouring a cold liquid
into a glass will cause drops of water to form on
the glass’ outer surface. This same phenomenon
occurs on the head drum of a player when it is
moved from a cool place to a warm place, after
heating a cold room, under extremely humid
conditions or in a place directly subjected to the
cool air from an air conditioner.
Model Number
Trade Name
: CU-VH1U
: JVC
Responsible party : JVC AMERICAS CORP.
Address
: 1700 Valley Road Wayne,
N J 07470
Telephone Number : 973-317–5000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the player itself.
Serious malfunctioning
Changes or modifications not approved by JVC
could void the user’s authority to operate the
equipment. This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference
in a residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
The player is a microcomputer-controlled device.
External noise and interference (from a TV, a
radio, etc.) might prevent it from functioning
properly. In such cases, first disconnect its power
supply unit (battery pack, AC Power Adapter/
Charger, etc.) and wait a few minutes and then re-
connect it and proceed as usual from the
beginning.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV
technician for help.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
55
USER MAINTENANCE
After Use
Cleaning The Player
1 Turn off the player.
1 To clean the exterior, wipe gently with a soft
cloth.
2 Slide and hold OPEN/EJECT in the direction of
the arrow, then pull the cassette holder cover
open until it locks. The cassette holder opens
automatically. Remove the cassette.
Put the cloth in diluted mild soap and wring it
well to wipe off heavy dirt. Then wipe again with
a dry cloth.
2 Press the Monitor Opening Button and open the
LCD monitor. Wipe gently with a soft cloth. Be
careful not to damage the monitor. Close the
LCD monitor.
3 Press “PUSH HERE” to close the cassette holder.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
NOTES:
4 Slide BATT.RELEASE 1 and remove the battery
● Avoid using strong cleaning agents such as
benzine or alcohol.
pack 2 3.
● Cleaning should be done only after the battery
pack has been removed or other power units have
been disconnected.
● When using a cleaner or chemically treated cloth
refer to the cautions of each product.
OPEN/EJECT Switch
Cassette holder
cover
Cassette
holder
Remove.
PUSH HERE
BATT.RELEASE Switch
Download from Www.Somanuals.com. All Manuals Search And Download.
56
EN
SPECIFICATIONS
Player
For General
Power supply
:
DC 6.3 V (Using AC Power Adapter/Charger)
DC 7.2 V (Using battery pack)
Power consumption
Dimensions (W x H x D)
:
:
Approx. 6.3 W (DV)/6.9 W (HD, SD)
211 mm x 52 mm x 154 mm (8-5/16" x 2-1/16" x 6-1/8")
(with the LCD monitor closed)
Weight
:
Approx. 1005 g (2.3 lbs)
(without cassette, memory card and battery)
Approx. 1145 g (2.6 lbs)
(incl. cassette, memory card and battery)
Operating temperature
Operating humidity
Storage temperature
LCD monitor
:
:
:
:
:
0°C to 40°C (32°F to 104°F)
35% to 80%
–20°C to 50°C (–4°F to 122°F)
3.5" diagonally measured, LCD panel/TFT active matrix system
Monaural
Speaker
For Video Playback
Signal format
Cassette
:
:
:
NTSC standard
Mini DV cassette
SP: 18.8 mm/s
LP: 12.5 mm/s
Tape speed
Maximum recording time
(using 80 min. cassette)
:
SP: 80 min.
LP: 120 min.
For D.S.C. Playback
Storage media
Compression system
File size
:
:
:
SD Memory Card/MultiMediaCard
JPEG (compatible)
3 modes
(DV: 640 x 480 pixels/SD: 848 x 480 pixels/HD:1280 x 720 pixels)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
57
For Connectors
S2
S-Video input
:
:
Y: 0.8 V to 1.2 V (p-p), 75 Ω, analog
C: 0.2 V to 0.4 V (p-p), 75 Ω, analog
Y: 1.0 V (p-p), 75 Ω, analog
C: 0.29 V (p-p), 75 Ω, analog
S-Video output
VIDEO
Video input
Video output
AUDIO
:
:
Y: 0.8 V to 1.2 V (p-p), 75 Ω, analog
Y: 1.0 V (p-p), 75 Ω, analog
Audio input
Audio output
Headphone output
Microphone input
i.LINK
:
:
:
:
300 mV (rms), 50 kΩ, analog, stereo
300 mV (rms), 1 kΩ, analog, stereo
Stereo
Stereo
Input/output
USB
Y/Pb/Pr output
:
:
:
4-pin, IEEE 1394 compliant
5-pin
Y: 1.0 V (p-p), 75 Ω, analog
Pb: 0.7 V (p-p), 75 Ω, analog
Pr: 0.7 V (p-p), 75 Ω, analog
AC Power Adapter/Charger
For General
Power requirement
U.S.A. and Canada
Other countries
Power consumption
Output
:
:
:
AC 120 Vd, 60 Hz
AC 110 V to 240 Vd, 50 Hz/60 Hz
23 W
Charge
VTR
:
:
DC 7.2 V G, 1.2 A
DC 6.3 V G, 1.8 A
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject
to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
58
EN
INDEX Controls, Connectors And Indicators
O
N
COMPONENT
VIDEO OUT
SNAP SHOT
LCD MONITOR
MENU
M
A
B
C
D
L
K
BLANK SEARCH
k
PLAY MODE
VIDEO
INDEX
INFO
NAVI NAVI STORE REC
J
MEMORY
E F G H I
g
h
i j
DV MPEG2
I.LINK OUT
Q
R
f S T U
W
P
X Y
m
l V e j
COMPONENT
VIDEO
Y
Pb
Pr
OUT
S2
VIDEO
L
AUDIO
R
Z
a
b
c
d
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
59
Controls
Indicators
a Menu Button [MENU]
(੬ pg. 28)
(੬ pg. 18)
(੬ pg. 18)
(੬ pg. 18)
(੬ pg. 23)
(੬ pg. 23)
(੬ pg. 32)
b Rewind Button [3
c Stop Button [8]
d Play/Pause Button [4/9]
e Index Button [INDEX]
f Information Button [INFO]
g Navigation Button [NAVI]
]
h Cassette Holder Cover
j Remote Sensor
(੬ pg. 16)
(੬ pg. 17)
(੬ pg. 39)
(੬ pg. 9)
(੬ pg. 14)
(੬ pg. 11)
(੬ pg. 18)
h Thumbnail Storing Button [NAVI STORE]
(੬ pg. 32)
i Recording Start/Stop Button [REC (7)]
(੬ pg. 34)
j Playback Mode Switch [VIDEO/MEMORY]
(੬ pg. 13)
k Blank Search Button [BLANK SEARCH]
(੬ pg. 19)
l LCD Monitor
l Fast-Forward Button [5
]
(੬ pg. 18)
(੬ pg. 15, 18)
(੬ pg. 38)
m RT Button
n Snapshot Button [SNAP SHOT]
o Video Output Mode Switch [COMPONENT
VIDEO OUT/LCD MONITOR] (੬ pg. 13, 34)
p i.LINK Output Select Switch [DV/MPEG2]
(੬ pg. 35)
q Cassette Open/Eject Switch
[OPEN/EJECT]
(੬ pg. 16)
(੬ pg. 14)
(੬ pg. 13)
r Monitor Opening Button
s Power Switch [ON, OFF]
t Speaker/Headphone Volume Control
[VOLUME +, –]
u LCD Monitor Brightness Control
[BRIGHT +, –]
(੬ pg. 18)
(੬ pg. 14)
v Battery Release Switch [BATT.RELEASE]
(੬ pg. 11)
Connectors
The connectors are located beneath the covers.
W USB (Universal Serial Bus) Connector
(੬ pg. 43)
X Headphone Connector [
]
(੬ pg. 9, 42)
No sound is output from the speaker when
headphones are connected to this connector.
Y Microphone connector [MIC]
Open the connector cover, and attach the
optional microphone.
(੬ pg. 9)
Z Component Video Connectors [Y/Pb/Pr]
(੬ pg. 20)
(੬ pg. 20, 34)
(੬ pg. 20, 34)
a S-Video connector [S2]
b Video Connector [VIDEO]
c Audio Connectors [AUDIO (L/R)]
(੬ pg. 20, 34, 42)
d Digital Video Connector [i] (i.Link*)
(੬ pg. 35, 36, 43)
* “i” refers to the IEEE1394-1995 industry
specification and extensions thereof. The logo
is used for products compliant with the i.Link
standard.
e DC Input Connector [DC]
(੬ pg. 11, 12)
Download from Www.Somanuals.com. All Manuals Search And Download.
60
EN
INDEX Indications
During D.S.C. Playback
LCD Monitor Indications
1
2
During Video Playback
100-0013
1
2
3 4 5 6
7
i.LINK in
BLANK SEARCH
PUSH "STOP" BUTTON
TO CANCEL
BR I GHT
8
g
4
3
:
a Operation Mode Indicator
b Folder/File Number
c Battery Indicator
(੬ pg. 23)
(੬ pg. 23)
(੬ pg. 49)
(੬ pg. 14)
g
q
9
0
a Video Playback Mode Indicator
b Sound Mode Indicator
(੬ pg. 37)
(੬ pg. 29)
(੬ pg. 19)
(੬ pg. 32)
d Brightness Control Indicator
(The level indicator g moves.)
c Blank Search Indicator
d Thumbnail Storing Indicator
(Appears while the captured image is being
stored as a thumbnail image in the memory
card.)
e Tape Speed
(੬ pg. 29)
f •U : Playback
•
•
5
: Fast-Forward/Shuttle Search
: Rewind/Shuttle Search
3
•9 : Pause
•9 U : Forward Frame-By-Frame Playback/
Slow-Motion
•Y 9 : Reverse Frame-By-Frame Playback/Slow-
Motion
•D : Audio Dubbing
•9D : Audio Dubbing Pause
(Appear while a tape is running.)
g Input Mode Indicator
h Battery Indicator
i Date/Time
(੬ pg. 34, 36)
(੬ pg. 49)
(੬ pg. 31)
j •VOLUME : Volume Level Indicator (Speaker or
headphone)
(The level indicator g moves.)
(੬ pg. 18)
•BRIGHT +, – : Brightness Control Indicator
(੬ pg. 14)
(The level indicator g moves.)
k Time Code*
(੬ pg. 31)
* This code is to confirm the location of the
recorded scene on the tape during playback.
Display
Minutes
Seconds
Frames
(30 frames = 1 second)
12 : 34 : 24
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
61
TERMS
A
Auto Playback Of Images ....................................22
VIDEO ..........................................................29
B
Battery Pack ............................................11, 12, 52
Beep (BEEP) .........................................................30
Blank search ........................................................19
Brightness Adjustment Of The Display ................14
N
C
Changing The Menu Settings ...............................28
Charging The Battery Pack ..................................11
Cleaning The Player ............................................55
Connections
Playback sound (SOUND MODE,
Playback Zoom ................................................... 41
Charging .......................................................11
To A TV Or VCR ...........................................20
R
D
Recording Time
Date/Time
Display (DATE/TIME) ....................................31
Settings .........................................................15
Deleting Files (DELETE) .......................................25
Display ................................................................31
Dubbing ......................................................34 – 38
Dubbing from tape to memory card
Record-Standby .................................................. 34
Remote Control ................................................... 39
Rewind The Tape ................................................ 18
S
(
COPY) .........................................29, 38
SD Memory Card ..........................................17, 53
Shuttle Search ..................................................... 19
Sound Mode (SOUND MODE) ........................... 29
Speaker Volume .................................................. 18
Special Effects (EFFECT)
E
Erase Protection .............................................16, 17
F
Fast-Forward The Tape ........................................18
Frame-By-Frame Playback ...................................40
Monotone (MONOTONE) ............................ 41
Sepia (SEPIA) ................................................ 41
Strobe (STROBE) ...........................................41
Specifications ................................................56, 57
Still Playback ......................................................18
S-Video output setting (S/VIDEO) ........................ 30
S-Video/AV input (S/AV INPUT) ....................29, 34
I
i.LINK output setting (i.LINK OUT) ......................30
Index Playback Of Files .......................................23
Indications on the LCD Monitor ..........................60
Initializing A Memory Card (FORMAT) ................27
L
Loading A Cassette ..............................................16
Loading A Memory Card .....................................17
T
Time Code (TIME CODE) ....................................31
U
Unloading A Cassette ..........................................16
Unloading A Memory Card .................................17
Download from Www.Somanuals.com. All Manuals Search And Download.
62
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
63
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Printed in Japan
0704FOH-ID-VP
“JVC” is the trademark or registered trademark of Victor Company of Japan, Limited.
© 2004 Victor Company of Japan, Limited.
US
Download from Www.Somanuals.com. All Manuals Search And Download.
|